Dialog DA14580-01UNA Bluetooth low energy 4.2 soc Datasheet

DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
General Description
42 kB System SRAM
84 kB ROM
 8 kB Retention SRAM
Power management
 Integrated Buck/Boost DC-DC converter
 P0, P1, P2 and P3 ports with 3.3 V tolerance
 Easy decoupling of only 4 supply pins
 Supports coin (typ. 3.0 V) and alkaline (typ. 1.5 V)
battery cells
 10-bit ADC for battery voltage measurement
Digital controlled oscillators
 16 MHz crystal (±20 ppm max) and RC oscillator
 32 kHz crystal (±50 ppm, ±500 ppm max) and
RCX oscillator
General purpose, Capture and Sleep timers
Digital interfaces
 General purpose I/Os: 14 (WLCSP34 package),
24 (QFN40 package), 32 (QFN48 package)
 2 UARTs with hardware flow control up to 1 MBd
 SPI+™ interface
 I2C bus at 100 kHz, 400 kHz
 3-axes capable Quadrature Decoder
Analog interfaces
 4-channel 10-bit ADC
Radio transceiver
 Fully integrated 2.4 GHz CMOS transceiver
 Single wire antenna: no RF matching or RX/TX
switching required
 Supply current at VBAT3V:
TX: 3.4 mA, RX: 3.7 mA (with ideal DC-DC)
 0 dBm transmit output power
 -20 dBm output power in “Near Field Mode”
 -93 dBm receiver sensitivity
Packages:
 WLCSP 34 pins, 2.436 mm x 2.436 mm
 QFN 40 pins, 5 mm x 5 mm
 QFN 48 pins, 6 mm x 6 mm
 KGD (wafer, dice)

The DA14580 integrated circuit has a fully integrated
radio transceiver and baseband processor for Bluetooth® low energy. It can be used as a standalone
application processor or as a data pump in hosted systems.
The DA14580 supports a flexible memory architecture
for storing Bluetooth profiles and custom application
code, which can be updated over the air (OTA). The
qualified Bluetooth low energy protocol stack is stored
in a dedicated ROM. All software runs on the ARM®
Cortex®-M0 processor via a simple scheduler.
The Bluetooth low energy firmware includes the
L2CAP service layer protocols, Security Manager
(SM), Attribute Protocol (ATT), the Generic Attribute
Profile (GATT) and the Generic Access Profile (GAP).
All profiles published by the Bluetooth SIG as well as
custom profiles are supported.





The transceiver interfaces directly to the antenna and
is fully compliant with the Bluetooth 4.2 standard.
The DA14580 has dedicated hardware for the Link
Layer implementation of Bluetooth low energy and
interface controllers for enhanced connectivity capabilities.


Features
Complies with Bluetooth V4.2, ETSI EN 300 328 and
EN 300 440 Class 2 (Europe), FCC CFR47 Part 15
(US) and ARIB STD-T66 (Japan)
 Processing power
 16 MHz 32 bit ARM Cortex-M0 with SWD inter
face
 Dedicated Link Layer Processor
 AES-128 bit encryption Processor
 Memories
 32 kB One-Time-Programmable (OTP) memory
________________________________________________________________________________________________

System Diagram
Datasheet
CFR0011-120-01
Revision 3.4
1 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Contents
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
System Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 8
4 System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1 ARM CORTEXM0 CPU . . . . . . . . . . . . . . . . . . 9
4.2 BLUETOOTH SMART . . . . . . . . . . . . . . . . . . . . 9
4.2.1 BLE Core . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.2 Radio Transceiver . . . . . . . . . . . . . . . . . 10
4.2.3 SmartSnippets  
4.3 MEMORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.4 FUNCTIONAL MODES . . . . . . . . . . . . . . . . . . .11
4.5 POWER MODES. . . . . . . . . . . . . . . . . . . . . . . 12
4.6 INTERFACES . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6.1 UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6.2 SPI+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6.3 I2C Interface . . . . . . . . . . . . . . . . . . . . . 12
4.6.4 General Purpose ADC . . . . . . . . . . . . . . 13
4.6.5 Quadrature Decoder . . . . . . . . . . . . . . . 13
4.6.6 Keyboard Controller . . . . . . . . . . . . . . . . 13
4.6.7 Input/Output Ports . . . . . . . . . . . . . . . . . 13
4.7 TIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7.1 General Purpose Timers . . . . . . . . . . . . 13
4.7.2 Wake-Up timer . . . . . . . . . . . . . . . . . . . . 14
4.7.3 Watchdog Timer. . . . . . . . . . . . . . . . . . . 14
4.8 CLOCK/RESET . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8.1 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8.2 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.9 POWER MANAGEMENT . . . . . . . . . . . . . . . . 15
5 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
7 Package Information . . . . . . . . . . . . . . . . . . . . . . . 151
7.1 MOISTURE SENSITIVITY LEVEL (MSL) . . . 151
7.2 WLCSP HANDLING . . . . . . . . . . . . . . . . . . . 151
7.3 SOLDERING INFORMATION . . . . . . . . . . . . 151
7.4 PACKAGE OUTLINES . . . . . . . . . . . . . . . . . 152
Datasheet
CFR0011-120-00-FM
Revision 3.4
2 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
1
FINAL
Block Diagram
24 April 2012
ARM Cortex M0
XTAL
32.768 kHz
DCDC
(BUCK/BOOST)
XTAL
16 MHz
LDO
SYS
CORE
ROM
84 kB
Radio
Transceiver
QUAD
DECODER
GP ADC
I2C
FIFO
SPI
FIFO
UART
UART2
APB bridge
Timer 2
3x PWM
FIFO
OTPC
Timer 0
1x PWM
KEYBOARD
CTRL
DMA
SW TIMER
WAKE UP
TIMER
OTP
32 kB
POWER/CLOCK
Management (PMU)
Ret. RAM4
1 kB
Memory Controller
Ret. RAM3
2 kB
RCX
POReset
LINK LAYER
HARDWARE
AES-128
System/
Exchange
RAM
42 kB
Ret. RAM2
3 kB
LDO
LDO
LDO
SYS
SYS
RF
RC
32 kHz
BLE Core
SWD (JTAG)
Ret. RAM
2 kB
LDO
RET
RC
16 MHz
GPIO MULTIPLEXING
Figure 1: DA14580 Block Diagram
Datasheet
CFR0011-120-01
Revision 3.4
3 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
2
FINAL
Pinout
• Quad Flat Package No Leads (QFN) with 48 pins
The DA14580 comes in three packages:
• Quad Flat Package No Leads (QFN) with 40 pins
• Wafer Level Chip Scale Package (WLCSP) with 34
balls
The actual pin/ball assignment is depicted in the following figures:
VP
P
P0
_0
G
N
P0
_5
4
P0
_
V
P0
_6
XT
AL
32
Kp
XT
AL
32
Km
VB
AT
P0
_7
_R
F
G
N
D
G
N
D
P0
_
P0
_
2
3
P0
_1
R
G
N
D
R
6
D
FI
O
p
5
G
ND
VB
AT
3
VD
RS
T
0
P1
_
CD
C
H
C
G
N
D
P1
_
P1
_1
VB
AT
1
F
V
SW
D
E
4
FI
O
m
3
2
LK
D
SW
IT
C
SW
_C
B
IO
A
2
XT
XT
AL
AL
16
16
M
M
m
p
VD
C
P1
D
C_
_3
R
F
1
NC
RFIOm
P3_7
P2_6
P2_5
VDCDC_RF
41
40
39
38
37
P2_7
44
RFIOp
P2_8
45
42
VPP
46
43
P2_9
P0_1
47
1
P2_0
P0_0
48
Figure 2: WLCSP34 ball assignment
XTAL16Mp
P0_3
4
33
P1_3
P3_0
5
P0_4
6
P0_5
7
P2_1
8
29
P1_1
P0_6
9
28
VBAT1V
P3_1
10
27
P1_0
P0_7
11
26
SWITCH
P3_2
12
25
P3_5
18
19
20
21
22
23
24
VBAT3V
GND
RST
P2_3
VDCDC
P2_4
SWDIO
P3_4
30
17
SW_CLK
(Top View)
16
P1_2
31
P2_2
32
DA14580
VBAT_RF
Pin 0: GND plane
15
34
P3_3
3
14
XTAL16Mm
P0_2
XTAL32Kp
35
13
P3_6
2
XTAL32Km
36
Figure 3: QFN48 Pin Assignment
Datasheet
CFR0011-120-01
Revision 3.4
4 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
P2_7
RFIOm
P2_6
P2_5
VDCDC_RF
34
33
32
31
P2_8
RFIOp
VPP
37
35
P2_9
39
38
36
P2_0
40
FINAL
P0_0
1
30
P0_1
2
29
XTAL16Mp
P0_2
3
28
P1_3
P0_3
4
NC
5
P0_4
6
P0_5
7
XTAL16Mm
27
P1_2
DA14580
26
SW_CLK
(Top View)
25
SWDIO
24
P1_1
17
18
19
20
RST
VDCDC
P2_4
16
P2_3
15
GND
Pin 0: GND
plane
VBAT3V
SWITCH
14
21
VBAT_RF
10
13
P0_7
P2_2
P1_0
12
VBAT1V
22
11
23
9
XTAL32Kp
8
XTAL32Km
P2_1
P0_6
Figure 4: QFN40 Pin Assignment
Table 1: Pin Description
Pin Name
Type
Drive
(mA)
Reset
State
Description
General Purpose I/Os
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
DIO
DIO
DIO
DIO
DIO
DIO
DIO
DIO
4.8
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
INPUT/OUTPUT with selectable pull up/down resistor. Pull-down
enabled during and after reset. General purpose I/O port bit or
alternate function nodes. Contains state retention mechanism
during power down.
P1_0
P1_1
P1_2
P1_3
P1_4/SWCLK
P1_5/SW_DIO
DIO
DIO
DIO
DIO
DIO
DIO
4.8
I-PD
I-PD
I-PD
I-PD
I-PD
I-PU
INPUT/OUTPUT with selectable pull up/down resistor. Pull-down
enabled during and after reset. General purpose I/O port bit or
alternate function nodes. Contains state retention mechanism
during power down.
This signal is the JTAG clock by default
This signal is the JTAG data I/O by default
P2_0
P2_1
P2_2
P2_3
P2_4
P2_5
P2_6
P2_7
P2_8
P2_9
DIO
DIO
DIO
DIO
DIO
DIO
DIO
DIO
DIO
DIO
4.8
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
INPUT/OUTPUT with selectable pull up/down resistor. Pull-down
enabled during and after reset. General purpose I/O port bit or
alternate function nodes. Contains state retention mechanism
during power down.
NOTE: This port is only available on the QFN40/QFN48 packages.
Datasheet
CFR0011-120-01
Revision 3.4
5 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 1: Pin Description
Drive
(mA)
Reset
State
DIO
DIO
DIO
DIO
DIO
DIO
DIO
DIO
4.8
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
I-PD
INPUT/OUTPUT with selectable pull up/down resistor. Pull-down
enabled during and after reset. General purpose I/O port bit or
alternate function nodes. Contain state retention mechanism during power down.
NOTE: This port is only available on the QFN48 package.
SWDIO/P1_5
DIO
4.8
I-PU
INPUT/OUTPUT. JTAG Data input/output. Bidirectional data and
control communication. Can also be used as a GPIO
SW_CLK/
P1_4
DIO
4.8
I-PD
INPUT JTAG clock signal. Can also be used as a GPIO
Pin Name
Type
P3_0
P3_1
P3_2
P3_3
P3_4
P3_5
P3_6
P3_7
Description
Debug Interface
Clocks
XTAL16Mp
AI
INPUT. Crystal input for the 16 MHz XTAL
XTAL16Mm
AO
OUTPUT. Crystal output for the 16 MHz XTAL
XTAL32kp
AI
INPUT. Crystal input for the 32.768 kHz XTAL
XTAL32km
AO
OUTPUT. Crystal output for the 32.768 kHz XTAL
Quadrature Decoder
QD_CHA_X
DI
INPUT. Channel A for the X axis. Mapped on Px ports
QD_CHB_X
DI
INPUT. Channel B for the X axis. Mapped on Px ports
QD_CHA_Y
DI
INPUT. Channel A for the Y axis. Mapped on Px ports
QD_CHB_Y
DI
INPUT. Channel B for the Y axis. Mapped on Px ports
QD_CHA_Z
DI
INPUT. Channel A for the Z axis. Mapped on Px ports
QD_CHB_Z
DI
INPUT. Channel B for the Z axis. Mapped on Px ports
DO
INPUT/OUTPUT. SPI Clock. Mapped on Px ports
SPI_DI
DI
INPUT. SPI Data input. Mapped on Px ports
SPI_DO
DO
OUTPUT. SPI Data output. Mapped on Px ports
SPI_EN
DI
INPUT. SPI Clock enable (active LOW). Mapped on Px ports
SPI Bus Interface
SPI_CLK
I2C Bus Interface
SDA
DIO/DIOD
INPUT/OUTPUT. I2C bus Data with open drain port. Mapped on
Px ports
SCL
DIO/DIOD
INPUT/OUTPUT. I2C bus Clock with open drain port. In open
drain mode, SCL is monitored to support bit stretching by a
slave. Mapped on Px ports.
UART Interface
UTX
DO
OUTPUT. UART transmit data. Mapped on Px ports
URX
DI
INPUT. UART receive data. Mapped on Px ports
URTS
DO
OUTPUT. UART Request to Send. Mapped on Px ports
UCTS
DI
INPUT. UART Clear to Send. Mapped on Px ports
UTX2
DO
OUTPUT. UART 2 transmit data. Mapped on Px ports
URX2
DI
INPUT. UART 2 receive data. Mapped on Px ports
URTS2
DO
OUTPUT. UART 2 Request to Send. Mapped on Px ports
UCTS2
DI
INPUT. UART 2 Clear to Send. Mapped on Px ports
Datasheet
CFR0011-120-01
Revision 3.4
6 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 1: Pin Description
Pin Name
Type
Drive
(mA)
Reset
State
Description
Analog Interface
ADC[0]
AI
INPUT. Analog to Digital Converter input 0. Mapped on P0[0]
ADC[1]
AI
INPUT. Analog to Digital Converter input 1. Mapped on P0[1]
ADC[2]
AI
INPUT. Analog to Digital Converter input 2. Mapped on P0[2]
ADC[3]
AI
INPUT. Analog to Digital Converter input 3. Mapped on P0[3]
Radio Transceiver
RFIOp
AIO
RF input/output. Impedance 50 
RFIOm
AIO
RF ground
Miscellaneous
RST
DI
INPUT. Reset signal (active high). Must be connected to GND if
not used.
VBAT_RF
AIO
Connect to VBAT3V on the PCB
VDCDC_RF
AIO
Connect to VDCDC on the PCB
VPP
AI
INPUT. This pin is used while OTP programming and testing.
OTP programming: VPP = 6.7 V ± 0.1 V
OTP Normal operation: leave VPP floating
Power Supply
VBAT3V
AIO
INPUT/OUTPUT. Battery connection. Used for a single coin battery (3 V). If an alkaline or a NiMH battery (1.5 V) is attached to
pin VBAT1V, this is the second output of the DC-DC converter.
VBAT1V
AI
INPUT. Battery connection. Used for an alkaline or a NiMh battery (1.5 V). If a single coin battery (3 V) is attached to pin
VBAT3V,this pin must be connected to GND.
SWITCH
AIO
INPUT/OUTPUT. Connection for the external DC-DC converter
inductor.
VDCDC
AO
Output of the DC-DC converter
GND
AIO
Datasheet
CFR0011-120-01
-
-
Ground
Revision 3.4
7 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
3
FINAL
Ordering Information
Table 2: Ordering Information (Samples)
Part Number
Package
Size (mm)
Shipment Form
Pack Quantity
DA14580-01UNA
WLCSP34
2.436 x 2.436
Mini-reel
50/100/1000
DA14580-01A31
QFN48
6x6
Tray
50
DA14580-01AT1
QFN40
5x5
Tray
50
Table 3: Ordering Information (Production)
Part Number
Package
Size (mm)
Shipment Form
Pack Quantity
DA14580-01UNA
WLCSP34
2.436 x 2.436
Mini-reel
5000
DA14580-01A32
QFN48
6x6
Reel
4000
DA14580-01AT2
QFN40
5x5
Reel
5000
DA14580-01WO4
KGD
wafer
Contact Dialog Semiconductor sales office
DA14580-01WC4
KGD
dice
Contact Dialog Semiconductor sales office
Table 4: Ordering Information (Preprogrammed OTP)
Part Number
Package
Shipment Form Pack Quantity
Description
DA14580-01PxA31
QFN48
Tray
50
Preprogrammed OTP, version x
DA14580-01PxAT1
QFN40
Tray
50
Preprogrammed OTP, version x
DA14580-01PxUNA
WLCSP34
Mini-reel
5000
Preprogrammed OTP, version x
DA14580-01PxA32
QFN48
Reel
4000
Preprogrammed OTP, version x
DA14580-01PxAT2
QFN40
Reel
4000
Preprogrammed OTP, version x
Part Number Legend:
DA14580-nn[ABC]XYZ
nn: chip revision number
A, AB or ABC: special version (optional)
XY: package code
Z: packing method
Datasheet
CFR0011-120-01
Revision 3.4
8 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
4
FINAL
System Overview
the architecture, which the OS can use as a tick
timer or as a general timer in other applications without an OS.
The DA14580 contains the following internal blocks:
4.1 ARM CORTEXM0 CPU
The Cortex-M0 processor is a 32-bit Reduced Instruction Set Computing (RISC) processor with a von Neumann architecture (single bus interface). It uses an
instruction set called Thumb, which was first supported
in the ARM7TDMI processor; however, several newer
instructions from the ARMv6 architecture and a few
instructions from the Thumb-2 technology are also
included. Thumb-2 technology extended the previous
Thumb instruction set to allow all operations to be carried out in one CPU state. The instruction set in
Thumb-2 includes both 16-bit and 32-bit instructions;
most instructions generated by the C compiler use the
16-bit instructions, and the 32-bit instructions are used
when the 16-bit version cannot carry out the required
operations. This results in high code density and
avoids the overhead of switching between two instruction sets.
In total, the Cortex-M0 processor supports only 56
base instructions, although some instructions can have
more than one form. Although the instruction set is
small, the Cortex-M0 processor is highly capable
because the Thumb instruction set is highly optimized.
Academically, the Cortex-M0 processor is classified as
load-store architecture, as it has separate instructions
for reading and writing to memory, and instructions for
arithmetic or logical operations that use registers.
• SuperVisor Call (SVC) instruction with a dedicated
SVC exception and PendSV (Pendable SuperVisor
service) to support various operations in an embedded OS.
• Architecturally defined sleep modes and instructions
to enter sleep. The sleep features allow power consumption to be reduced dramatically. Defining sleep
modes as an architectural feature makes porting of
software easier because sleep is entered by a specific instruction rather than implementation defined
control registers.
• Fault handling exception to catch various sources of
errors in the system.
• Support for 24 interrupts.
• Little endian memory support.
• Wake up Interrupt Controller (WIC) to allow the processor to be powered down during sleep, while still
allowing interrupt sources to wake up the system.
• Halt mode debug. Allows the processor activity to
stop completely so that register values can be
accessed and modified. No overhead in code size
and stack memory size.
• CoreSight technology. Allows memories and peripherals to be accessed from the debugger without halting the processor.
• Thumb instruction set. Highly efficient, high code
density and able to execute all Thumb instructions
from the ARM7TDMI processor.
• Supports Serial Wire Debug (SWD) connections.
The serial wire debug protocol can handle the same
debug features as the JTAG, but it only requires two
wires and is already supported by a number of
debug solutions from various tools vendors.
• High performance. Up to 0.9 DMIPS/MHz (Dhrystone 2.1) with fast multiplier.
• Four (4) hardware breakpoints and two (2) watch
points.
• Built-in Nested Vectored Interrupt Controller (NVIC).
This makes interrupt configuration and coding of
exception handlers easy. When an interrupt request
is taken, the corresponding interrupt handler is executed automatically without the need to determine
the exception vector in software.
• Breakpoint instruction support for an unlimited number of software breakpoints.
Features
• Interrupts can have four different programmable priority levels. The NVIC automatically handles nested
interrupts.
• Programmer’s model similar to the ARM7TDMI processor. Most existing Thumb code for the
ARM7TDMI processor can be reused. This also
makes it easy for ARM7TDMI users, as there is no
need to learn a new instruction set.
• The design is configured to respond to exceptions
(e.g. interrupts) as soon as possible (minimum 16
clock cycles).
4.2 BLUETOOTH SMART
• Non maskable interrupt (NMI) input for safety critical
systems.
The BLE (Bluetooth low energy) core is a qualified
Bluetooth baseband controller compatible with the
Bluetooth low energy 4.2 specification and it is in
charge of packet encoding/decoding and frame scheduling.
• Easy to use and C friendly. There are only two
modes (Thread mode and Handler mode). The
whole application, including exception handlers, can
be written in C without any assembler.
• Built-in System Tick timer for OS support. A 24-bit
timer with a dedicated exception type is included in
Datasheet
CFR0011-120-00-FM
4.2.1 BLE Core
Features
• All device classes support (Broadcaster, Central,
Observer, Peripheral)
Revision 3.4
9 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
• All packet types (Advertising / Data / Control)
• Encryption (AES / CCM)
• Bit stream processing (CRC, Whitening)
• FDMA/TDMA/events formatting and synchronization
• Frequency hopping calculation
• Operating clock 16 MHz or 8 MHz
• Low power modes supporting 32.0 kHz or
32.768 kHz
• Supports power down of the baseband during the
protocol’s idle periods
• AHB Slave interface for register file access
• AHB Slave interface for Exchange Memory access
of CPU via BLE core
• AHB Master interface for direct access of BLE core
to Exchange Memory space
4.2.2 Radio Transceiver
The Radio Transceiver implements the RF part of the
Bluetooth low energy protocol. Together with the Bluetooth 4.2 PHY layer, this provides a 93 dB RF link
budget for reliable wireless communication.
All RF blocks are supplied by on-chip low-drop out-regulators (LDOs). The bias scheme is programmable per
block and optimized for minimum power consumption.
The Bluetooth LE radio comprises the Receiver, Transmitter, Synthesizer, Rx/Tx combiner block, and Biasing
LDOs.
Figure 5: SmartSnippets Stack
Apart from the protocol stack, the Software platform
supports a Hardware Abstraction Layer (HAL) which
enables easy access to peripheral’s features from a
programmer’s point of view, as presented in the following figure.
Features
• Single ended RFIO interface, 50  matched
• Alignment free operation
• -93 dBm receiver sensitivity
• 0 dBm transmit output power
• Ultra low power consumption
• Fast frequency tuning minimizes overhead
4.2.3 SmartSnippets
The DA14580 comes complete with Dialog’s SmartSnippets Bluetooth Software platform which includes
a qualified Bluetooth Smart single-mode stack on chip.
Numerous Bluetooth Smart profiles for consumer wellness, sport, fitness, security and proximity applications
are supplied as standard, while additional customer
profiles can be developed and added as needed.
The SmartSnippets software development environment is based on Keil’s uVision mature tools and
contains example application code for both embedded
and hosted modes.
Datasheet
CFR0011-120-00-FM
Revision 3.4
10 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Application
Accelerometer
Driver
SPI FLASH
Driver
Sample
Drivers
Battery
Driver
CORE
Drivers
EEPROM
I2C
Driver
GPIO
Driver
SPI
Driver
UART
Driver
ADC
Driver
Quadrature
Timers
Figure 6: Hardware Abstraction Layer
Core drivers are provided for each interface of the
DA14580 enabling optimized usage of the hardware’s
capabilities. These drivers provide an easy-to-use
interface towards the hardware engines without having
to interfere with the register programming directly.
On top of the core drivers, a number of sample drivers
is also provided enabling communication with basic
Bluetooth Smart application components: accelerometers, FLASH/EEPROM non-volatile memories, etc.
4.3 MEMORIES
The following memories are part of the DA14580’s
internal blocks:
ROM. This is a 84 kB ROM containing the Bluetooth
low energy protocol stack as well as the boot code
sequence.
OTP. This is a 32 kB One-Time Programmable memory
array, used to store the application code as well as
Bluetooth low energy profiles. It also contains the system configuration and calibration data.
System SRAM. This is a 42 kB system SRAM (SysRAM) which is primarily used for mirroring the program
code from the OTP when the system wakes/powers
up. It also serves as Data RAM for intermediate variables and various data that the protocol requires.
Optionally, it can be used as extra memory space for
the BLE TX and RX data structures.
Retention RAMs. These are 4 special low leakage
SRAM cells (2 kB + 2 kB + 3 kB + 1 kB) used to store
various data of the Bluetooth low energy protocol as
well as the system’s global variables and processor
stack when the system goes into Deep Sleep mode.
Storage of this data ensures secure and quick configuration of the BLE Core after the system wakes up.
Every cell can be powered on or off according to the
application needs for retention area when in Deep
Datasheet
CFR0011-120-00-FM
Sleep mode.
4.4 FUNCTIONAL MODES
The DA14580 is optimized for deeply embedded applications such as health monitoring, sports measuring,
human interaction devices etc. Customers are able to
develop and test their own applications. Upon completion of the development, the application code can be
programmed into the OTP. In general, the system has
three functional modes of operation:
A. Development Mode: During this phase application
code is developed using the ARM Cortex-M0 SW environment. The compiled code is then downloaded into
the System RAM or any Retention RAMs by means of
SWD (JTAG) or any serial interface (e.g. UART).
Address 0x00 is remapped to the physical memory that
contains the code and the CPU is configured to reset
and execute code from the remapped device. This
mode is enabling application development, debugging
and on-the-fly testing.
B. Normal Mode: After the application is ready and
verified, the code can be burned into the OTP. When
the system boots/wakes up, the DMA of the OTP controller will automatically copy the program code from
the OTP into the system RAM. Next, a SW reset or a
jump to the System RAM occurs and code execution is
started. Hence, in this mode, the system is autonomous, contains the required SW in OTP and is ready
for integration into the final product.
C. Calibration Mode: Between Development and Normal mode, there is an intermediate stage where the
chip needs to be calibrated with respect to two important features:
• Programming of the Bluetooth device address
• Programming of the trimming value for the external
16 MHz crystal.
Revision 3.4
11 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
This mode of operation applies to the final product and
is performed by the customer. During this phase, certain fields in the OTP should be programmed.
4.5 POWER MODES
There are four different power modes in the DA14580:
• Active mode: System is active and operates at full
speed.
• Sleep mode: No power gating has been programmed, the ARM CPU is idle, waiting for an interrupt. PD_SYS is on. PD_PER and PED_RAD
depending on the programmed enabled value.
• Extended Sleep mode: All power domains are off
except for the PD_AON, the programmed PD_RRx
and the PD_SR. Since the SysRAM retains its data,
no OTP mirroring is required upon waking up the
system.
• Deep Sleep mode: All power domains are off except
for the PD_AON and the programmed PD_RRx.
This mode dissipates the minimum leakage power.
However, since the SysRAM has not retained its
data, an OTP mirror action is required upon waking
up the system.
• Prioritized interrupt identification
• Programmable serial data baud rate as calculated
by the following: baud rate = (serial clock frequency)/
(divisor).
4.6.2 SPI+
This interface supports a subset of the Serial Peripheral Interface (SPITM). The serial interface can transmit
and receive 8, 16 or 32 bits in master/slave mode and
transmit 9 bits in master mode. The SPI+ interface has
enhanced functionality with bidirectional 2x16-bit word
FIFOs.
SPI is a trademark of Motorola, Inc.
Features
• Slave and Master mode
• 8 bit, 9 bit, 16 bit or 32 bit operation
• Clock speeds up to 16 MHz for the SPI controller.
Programmable output frequencies of SPI source
clock divided by 1, 2, 4, 8
• SPI clock line speed up to 8 MHz
• SPI mode 0, 1, 2, 3 support (clock edge and phase)
4.6 INTERFACES
• Programmable SPI_DO idle level
4.6.1 UARTs
• Maskable Interrupt generation
The UART is compliant to the industry-standard 16550
and is used for serial communication with a peripheral,
modem (data carrier equipment, DCE) or data set.
Data is written from a master (CPU) over the APB bus
to the UART and it is converted to serial form and
transmitted to the destination device. Serial data is also
received by the UART and stored for the master (CPU)
to read back.
• Bus load reduction by unidirectional writes-only and
reads-only modes.
Built-in RX/TX FIFOs for continuous SPI bursts.
4.6.3 I2C Interface
Features
The I2C interface is a programmable control bus that
provides support for the communications link between
Integrated Circuits in a system. It is a simple two-wire
bus with a software-defined protocol for system control,
which is used in temperature sensors and voltage level
translators to EEPROMs, general-purpose I/O, A/D
and D/A converters.
• 16 bytes Transmit and receive FIFOs
Features
• Hardware flow control support (CTS/RTS)
• Two-wire I2C serial interface consists of a serial data
line (SDA) and a serial clock (SCL)
There is no DMA support on the UART block since its
contains internal FIFOs. Both UARTs support hardware
flow control signals (RTS, CTS, DTR, DSR).
• Shadow registers to reduce software overhead and
also include a software programmable reset
• Two speeds are supported:
• Transmitter Holding Register Empty (THRE) interrupt mode
• Standard mode (0 to 100 kbit/s)
• IrDA 1.0 SIR mode supporting low power mode.
• Clock synchronization
• Functionality based on the 16550 industry standard:
• 32 deep transmit/receive FIFOs
• Programmable character properties, such as number of data bits per character (5-8), optional
• Master transmit, Master receive operation
• parity bit (with odd or even select) and number of
stop bits (1, 1.5 or 2)
• 7 or 10-bit combined format transfers
• Line break generation and detection
• Fast mode (<= 400 kbit/s)
• 7 or 10-bit addressing
• Bulk transmit mode
• Default slave address of 0x055
Datasheet
CFR0011-120-00-FM
Revision 3.4
12 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
• Interrupt or polled-mode operation
• Handles Bit and Byte waiting at both bus speeds
4.6.6 Keyboard Controller
• Programmable SDA hold time
The Keyboard controller can be used for debouncing
the incoming GPIO signals when implementing a keyboard scanning engine. It generates an interrupt to the
CPU (KEYBR_IRQ).
4.6.4 General Purpose ADC
The DA14580 is equipped with a high-speed ultra low
power 10-bit general purpose Analog-to-Digital Converter (GPADC). It can operate in unipolar (single
ended) mode as well as in bipolar (differential) mode.
The ADC has its own voltage regulator (LDO) of 1.2 V,
which represents the full scale reference voltage.
Features
In parallel, five extra interrupt lines can be triggered by
a state change on 32 selectable GPIOs (GPIOx_IRQ).
Features
• Monitors any of the 32 available GPIOs (12 in the
WLCSP package, 22 in the QFN40 and 32 in the
QFN48)
• Generates a keyboard interrupt on key press or key
release
• 10-bit dynamic ADC with 65 ns conversion time
• Maximum sampling rate 3.3 Msample/s
• Implements debouncing time from 0 up to 63 ms
• Ultra low power (5 A typical supply current at
100 ksample/s)
Supports five separate interrupt generation lines from
GPIO toggling
• Single-ended as well as differential input with two
input scales
4.6.7 Input/Output Ports
• Four single-ended or two differential external input
channels
The DA14580 has software-configurable I/O pin
assignment, organized into ports Port 0, Port1, Port2
and Port 3. Port 2 is only available at the QFN40 package while ports 2 and 3 are available at the QFN48
package.
• Battery monitoring function
• Chopper function
• Offset and zero scale adjust
Features
• Common-mode input level adjust
• Port 0: 8 pins, Port 1: 6 pins (including SW_CLK and
SWDIO), Port 2: 10 pins, Port 3: 8 pins
• Fully programmable pin assignment
4.6.5 Quadrature Decoder
This block decodes the pulse trains from a rotary
encoder to provide the step and the direction of the
movement of an external device. Three axes (X, Y, Z)
are supported.
The integrated quadrature decoder can automatically
decode the signals for the X, Y and Z axes of a HID
input device, reporting step count and direction: the
channels are expected to provide a pulse train with 90
degrees phase difference; depending on whether the
reference channel is leading or lagging, the direction
can be determined.
This block can be used for waking up the chip as soon
as there is any kind of movement from the external
device connected to it.
• Selectable 25 k pull-up, pull-down resistors per pin
• Pull-up voltage either VBAT3V (BUCK mode) or
VBAT1V (BOOST mode) configurable per pin
• Fixed assignment for analog pin ADC[3:0]
• Pins retain their last state when system enters the
Extended or Deep Sleep mode.
4.7 TIMERS
4.7.1 General Purpose Timers
The Timer block contains 2 timer modules that are software controlled, programmable and can be used for
various tasks.
Features
Timer 0
• Three 16-bit signed counters that provide the step
count and direction on each of the axes (X, Y and Z)
• 16-bit general purpose timer
• Programmable system clock sampling at maximum
16 MHz.
• APB interface for control and programming
• Programmable source from P0, P1 and P2 ports
• Ability to generate 2 Pulse Width Modulated signals
(PWM0 and PWM1, with common programming)
• Programmable output frequency:
16, 8, 4, 2 MHz or 32 kHz 
f = -----------------------------------------------------------------------M + 1 + N + 1
with N = 0 to (216-1), M = 0 to (216-1)
• Digital filter on the channel inputs to avoid spikes
Datasheet
CFR0011-120-00-FM
Revision 3.4
13 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
• Programmable duty cycle:
M+1
 = --------------------------------------------  100 %
M + 1 + N + 1
A minimum pulse duration of 2 sleep clock cycles must
be applied to the GPIO to ensure a successful system
wake-up.
• Separately programmable interrupt timer:
16, 8, 4, 2 MHz or 32 kHz 
T = ----------------------------------------------------------------------- ON + 1 
4.7.3 Watchdog Timer
Timer 2
• 14-bit general purpose timer
• Ability to generate 3 Pulse Width Modulated signals
(PWM2, PWM3 and PWM4)
The Watchdog timer is an 8-bit timer with sign bit that
can be used to detect an unexpected execution
sequence caused by a software run-away and can
generate a full system reset or a Non-Maskable Interrupt (NMI).
• Input clock frequency:
f IN = sys_clk
------------------- with N = 1, 2, 4 or 8
N
and sys_clk = 16 MHz or 32 kHz
Features
• Programmable output frequency:
• Optional automatic WDOG reset if NMI handler fails
to update the Watchdog register.
f OUT
• 8 bits down counter with sign bit, clocked with a
10.24 ms clock for a maximum 2.6 s time-out.
• Non-Maskable Interrupt (NMI) or WDOG reset.
f IN
 f IN 
-
=  ------ to  ---------------- 2
 2 14 – 1
• Non-maskable Watchdog freeze of the Cortex-M0
Debug module when the Cortex-M0 is halted in
Debug state.
• Three outputs with Programmable duty cycle from
0 % to 100 %
Maskable Watchdog freeze by user program. Note that
if the system is not remapped, i.e. SysRAM is at
address 0x20000000, then a watchdog fire will trigger
the BootROM code to be executed again.
• Used for white LED intensity (on/off) control
4.7.2 Wake-Up timer
The Wake-up timer can be programmed to wake up the
DA14580 from power down mode after a preprogrammed number of GPIO events.
4.8 CLOCK/RESET
Features
4.8.1 Clocks
• Monitors any GPIO state change
The Digital Controlled Xtal Oscillator (DXCO) is a
Pierce configured type of oscillator designed for low
power consumption and high stability. There are two
such crystal oscillators in the system, one at 16
MHz(XTAL16M) and a second at 32.768 kHz
(XTAL32K). The 32.768 kHz oscillator has no trimming
capabilities and is used as the clock of the Extended/
Deep Sleep modes. The 16 MHz oscillator can be
trimmed.
• Implements debouncing time from 0 up to 63 ms
• Accumulates external events and compares the
number to a programmed value
• Generates an interrupt to the CPU
The principle schematic of the two oscillators is shown
in Figure 7 below. No external components to the
DA14580 are required other than the crystal itself. If
the crystal has a case connection, it is advised to connect the case to ground.
Datasheet
CFR0011-120-00-FM
Revision 3.4
14 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
1. LDO RET: This is the LDO providing power to the
Retention domain (PD_AON). It powers the Retention
RAMs and the digital part which is always on.
XTAL32Km
32.768 kHz
XTAL32Kp
XTAL16Mp
16 MHz
XTAL16Mm
LDO groups in the system:
2. LDO OTP: This is the LDO powering the OTP macro
cell. This is the reason for using the step-up DC-DC
converter when running from an Alkaline battery.
3. LDO SYS: This is the LDO providing the system with
the actual VDD power required for the digital part to
operate. Note that the Power Block implements seamless switching from the LDO SYS to the LDO RET
when the system enters Deep Sleep mode. In the latter
case, a low voltage is applied to the PD_AON power
domain to further reduce leakage.
0-22.4 pF
clock16MHz
clock32kHz
4. LDO (various): This a group of LDOs used for the
elaborate control of the powering up/down of the
Radio, the GP ADC and the XTAL16M oscillator.
Figure 7: Crystal Oscillator Circuits
There are 3 RC oscillators in the DA14580: one providing 16 MHz (RC16M), one providing 32 kHz (RC32K)
and one providing a frequency in the range of 10.5 kHz
(RCX).
4.8.2 Reset
There are two ways of connecting external batteries to
the Power Block of the DA14580. They depend on the
specific battery cell used and its voltage range. Battery
cells are distinguished into Lithium coin cells (2.35 V to
3.3 V) and Alkaline cells (1.0 V to 1.8 V). The connection diagrams are presented in Figure 9 and Figure 8
respectively:
The DA14580 comprises an RST pad which is active
high. It contains an RC filter for spikes suppression
with 400 k and 2.8 pF for the resistor and the capacitor respectively. It also contains a 25 k pull-down
resistor. This pad should be connected to ground if not
needed by the application. The typical latency of the
RST pad is in the range of 2 s.
4.9 POWER MANAGEMENT
The DA14580 has a complete power management
function integrated with Buck or Boost DC-DC converter and separate LDOs for the different power
domains of the system.
Features
• On-chip LDOs, without external capacitors
• Synchronous DC-DC converter which can be configured as either:
• Boost (step-up) converter, starting from 0.9 V,
when running from an Alkaline/NiMH cell.
• Buck (step-down) converter for increased efficiency when running from a Lithium coin-cell or 2
Alkaline batteries down to 2.35 V.
• Battery voltage measurement ADC (multiplexed
input from general purpose ADC)
• Use of small external components (2.2 H inductor
and 1F capacitor)
The Power Block contains a DC-DC converter which
can be configured to operate as a Step-Up or a StepDown converter. The converter provides power to four
Datasheet
CFR0011-120-00-FM
Revision 3.4
15 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
analog/RF
VDCDC_RF
LDO
LDO
digital
retention
VBAT1V
VDCDC
SWITCH
2.35 V to 3.3 V
Lithium
coin-cell
VBAT3V
VBAT_RF
FINAL
LDO
analog/RF
Buck Converter
DA14580
Figure 8: Supply Overview, Coin-Cell Application
0.9 V to 2.0 V
VBAT1V
SWITCH
internal supply for boost conv. VBAT3V
< 0.9 V
Alkaline
or
NiMH
VDCDC
on
Boost Converter
VDCDC_RF
LDO
LDO
digital
LDO
VBAT_RF
analog/RF
retention
DA14580
Figure 9: Supply Overview, Alkaline-Cell Application
The usage of Boost or Buck mode with respect to the
provided voltage ranges is illustrated in the following
figure which also illustrates the efficiency of the engine
assuming a 10 mA constant load.
Datasheet
CFR0011-120-00-FM
Revision 3.4
16 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
DC‐DC Efficiency vs Voltage
95%
90%
85%
80%
75%
70%
65%
60%
55%
50%
0
0.5
0.9
1
1.5
Buck
Boost
1.8
2
2.35
2.5
3
3.5
Boost (Vout > 1.4 V)
Figure 10: DC-DC Efficiency in Buck/Boost Mode at
Various Voltage Levels
The X axis represents the supply voltage. BOOST
mode should be used when voltage ranges from 0.9 V
to 2.0 V to sustain a decent efficiency over 70 %. From
that point on, the power dissipation becomes quite
large.
BUCK mode can operate correctly with voltages in the
range of 2.35 V to 3.3 V.
There are two voltage areas in Figure 10 designated by
dashed lines. The first one (0 V to 0.9 V) indicates that
the DA14580 is not operational when the voltage is
below 0.9 V. This is the absolute threshold for the DCDC converter Boost mode.
The second area (1.8 V to 2.2 V) indicates that Deep
Sleep mode is not allowed when the DC-DC converter
is configured in BUCK mode and the voltage is within
this range, because the OTP will not be readable any
more. However, this part of the voltage range can be
covered by the BOOST mode. Furthermore, when
BUCK mode is mandatory, Extended Sleep mode can
be activated instead of Deep Sleep mode, thus not
using the OTP for the code mirroring but retain the
code in SysRAM.
Note: The system should never be cold booted when
the supply voltage is less than 2.5 V. A manual power
up with a power supply less than 2.5 V in buck mode
might create instability.
Datasheet
CFR0011-120-00-FM
Revision 3.4
17 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
5
FINAL
Registers
This section contains a detailed view of the DA14580 registers. It is organized as follows: An overview table is presented initially, which depicts all register names, addresses and descriptions. A detailed bit level description of each
register follows.
The register file of the ARM Cortex-M0 can be found in the following documents, available on the ARM website:
Devices Generic User Guide:
DUI0497A_cortex_m0_r0p0_generic_ug.pdf
Technical Reference Manual:
DDI0432C_cortex_m0_r0p0_trm.pdf
These documents contain the register descriptions for the Nested Vectored Interrupt Controller (NVIC), the System
Control Block (SCB) and the System Timer (SysTick).
Datasheet
CFR0011-120-01
Revision 3.4
18 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 5: Register Map
Address
0x40008000
Port
Description
OTPC_MODE_REG
Mode register
0x40008004
OTPC_PCTRL_REG
Bit-programming control register
0x40008008
OTPC_STAT_REG
Status register
0x4000800C
OTPC_AHBADR_REG
AHB master start address
0x40008010
OTPC_CELADR_REG
Macrocell start address
0x40008014
OTPC_NWORDS_REG
Number of words
0x40008018
OTPC_FFPRT_REG
Ports access to fifo logic
0x4000801C
OTPC_FFRD_REG
Latest read data from the OTPC_FFPRT_REG
0x50000000
CLK_AMBA_REG
HCLK, PCLK, divider and clock gates
0x50000002
CLK_FREQ_TRIM_REG
Xtal frequency trimming register
0x50000004
CLK_PER_REG
Peripheral divider register
0x50000008
CLK_RADIO_REG
Radio PLL control register
0x5000000A
CLK_CTRL_REG
Clock control register
0x50000010
PMU_CTRL_REG
Power Management Unit control register
0x50000012
SYS_CTRL_REG
System Control register
0x50000014
SYS_STAT_REG
System status register
0x50000016
TRIM_CTRL_REG
Control trimming of the XTAL16M
0x50000020
CLK_32K_REG
32 kHz oscillator register
0x50000022
CLK_16M_REG
16 MHz RC-oscillator register
0x50000024
CLK_RCX20K_REG
20 kHz RXC-oscillator control register
0x50000028
BANDGAP_REG
Bandgap trimming
0x5000002A
ANA_STATUS_REG
Status bit of analog (power management) circuits
0x50000100
WKUP_CTRL_REG
Control register for the wakeup counter
0x50000102
WKUP_COMPARE_REG
Number of events before wakeup interrupt
0x50000104
WKUP_RESET_IRQ_REG
Reset wakeup interrupt
0x50000106
WKUP_COUNTER_REG
Actual number of events of the wakeup counter
0x50000108
WKUP_RESET_CNTR_REG
Reset the event counter
0x5000010A
WKUP_SELECT_P0_REG
Select which inputs from P0 port can trigger wkup
counter
0x5000010C
WKUP_SELECT_P1_REG
Select which inputs from P1 port can trigger wkup
counter
0x5000010E
WKUP_SELECT_P2_REG
Select which inputs from P2 port can trigger wkup
counter
0x50000110
WKUP_SELECT_P3_REG
Select which inputs from P3 port can trigger wkup
counter
0x50000112
WKUP_POL_P0_REG
Select the sensitivity polarity for each P0 input
0x50000114
WKUP_POL_P1_REG
Select the sensitivity polarity for each P1 input
0x50000116
WKUP_POL_P2_REG
Select the sensitivity polarity for each P2 input
0x50000118
WKUP_POL_P3_REG
Select the sensitivity polarity for each P3 input
0x50000200
QDEC_CTRL_REG
Quad Decoder control register
0x50000202
QDEC_XCNT_REG
Counter value of the X Axis
0x50000204
QDEC_YCNT_REG
Counter value of the Y Axis
0x50000206
QDEC_CLOCKDIV_REG
Clock divider register
0x50000208
QDEC_CTRL2_REG
Quad Decoder control register
Datasheet
CFR0011-120-01
Revision 3.4
19 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 5: Register Map
Address
Port
Description
0x5000020A
QDEC_ZCNT_REG
Z_counter
0x50001000
UART_RBR_THR_DLL_REG
Receive Buffer Register
0x50001004
UART_IER_DLH_REG
Interrupt Enable Register
0x50001008
UART_IIR_FCR_REG
Interrupt Identification Register/FIFO Control Register
0x5000100C
UART_LCR_REG
Line Control Register
0x50001010
UART_MCR_REG
Modem Control Register
0x50001014
UART_LSR_REG
Line Status Register
0x50001018
UART_MSR_REG
Modem Status Register
0x5000101C
UART_SCR_REG
Scratchpad Register
0x50001020
UART_LPDLL_REG
Low Power Divisor Latch Low
0x50001024
UART_LPDLH_REG
Low Power Divisor Latch High
0x50001030
UART_SRBR_STHR0_REG
Shadow Receive/Transmit Buffer Register
0x50001034
UART_SRBR_STHR1_REG
Shadow Receive/Transmit Buffer Register
0x50001038
UART_SRBR_STHR2_REG
Shadow Receive/Transmit Buffer Register
0x5000103C
UART_SRBR_STHR3_REG
Shadow Receive/Transmit Buffer Register
0x50001040
UART_SRBR_STHR4_REG
Shadow Receive/Transmit Buffer Register
0x50001044
UART_SRBR_STHR5_REG
Shadow Receive/Transmit Buffer Register
0x50001048
UART_SRBR_STHR6_REG
Shadow Receive/Transmit Buffer Register
0x5000104C
UART_SRBR_STHR7_REG
Shadow Receive/Transmit Buffer Register
0x50001050
UART_SRBR_STHR8_REG
Shadow Receive/Transmit Buffer Register
0x50001054
UART_SRBR_STHR9_REG
Shadow Receive/Transmit Buffer Register
0x50001058
UART_SRBR_STHR10_REG
Shadow Receive/Transmit Buffer Register
0x5000105C
UART_SRBR_STHR11_REG
Shadow Receive/Transmit Buffer Register
0x50001060
UART_SRBR_STHR12_REG
Shadow Receive/Transmit Buffer Register
0x50001064
UART_SRBR_STHR13_REG
Shadow Receive/Transmit Buffer Register
0x50001068
UART_SRBR_STHR14_REG
Shadow Receive/Transmit Buffer Register
0x5000106C
UART_SRBR_STHR15_REG
Shadow Receive/Transmit Buffer Register
0x5000107C
UART_USR_REG
UART Status register.
0x50001080
UART_TFL_REG
Transmit FIFO Level
0x50001084
UART_RFL_REG
Receive FIFO Level.
0x50001088
UART_SRR_REG
Software Reset Register.
0x5000108C
UART_SRTS_REG
Shadow Request to Send
0x50001090
UART_SBCR_REG
Shadow Break Control Register
0x50001094
UART_SDMAM_REG
Shadow DMA Mode
0x50001098
UART_SFE_REG
Shadow FIFO Enable
0x5000109C
UART_SRT_REG
Shadow RCVR Trigger
0x500010A0
UART_STET_REG
Shadow TX Empty Trigger
0x500010A4
UART_HTX_REG
Halt TX
0x500010F4
UART_CPR_REG
Component Parameter Register
0x500010F8
UART_UCV_REG
Component Version
0x500010FC
UART_CTR_REG
Component Type Register
0x50001100
UART2_RBR_THR_DLL_REG
Receive Buffer Register
0x50001104
UART2_IER_DLH_REG
Interrupt Enable Register
0x50001108
UART2_IIR_FCR_REG
Interrupt Identification Register/FIFO Control Register
Datasheet
CFR0011-120-01
Revision 3.4
20 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 5: Register Map
Address
Port
Description
0x5000110C
UART2_LCR_REG
Line Control Register
0x50001110
UART2_MCR_REG
Modem Control Register
0x50001114
UART2_LSR_REG
Line Status Register
0x50001118
UART2_MSR_REG
Modem Status Register
0x5000111C
UART2_SCR_REG
Scratchpad Register
0x50001120
UART2_LPDLL_REG
Low Power Divisor Latch Low
0x50001124
UART2_LPDLH_REG
Low Power Divisor Latch High
0x50001130
UART2_SRBR_STHR0_REG
Shadow Receive/Transmit Buffer Register
0x50001134
UART2_SRBR_STHR1_REG
Shadow Receive/Transmit Buffer Register
0x50001138
UART2_SRBR_STHR2_REG
Shadow Receive/Transmit Buffer Register
0x5000113C
UART2_SRBR_STHR3_REG
Shadow Receive/Transmit Buffer Register
0x50001140
UART2_SRBR_STHR4_REG
Shadow Receive/Transmit Buffer Register
0x50001144
UART2_SRBR_STHR5_REG
Shadow Receive/Transmit Buffer Register
0x50001148
UART2_SRBR_STHR6_REG
Shadow Receive/Transmit Buffer Register
0x5000114C
UART2_SRBR_STHR7_REG
Shadow Receive/Transmit Buffer Register
0x50001150
UART2_SRBR_STHR8_REG
Shadow Receive/Transmit Buffer Register
0x50001154
UART2_SRBR_STHR9_REG
Shadow Receive/Transmit Buffer Register
0x50001158
UART2_SRBR_STHR10_REG
Shadow Receive/Transmit Buffer Register
0x5000115C
UART2_SRBR_STHR11_REG
Shadow Receive/Transmit Buffer Register
0x50001160
UART2_SRBR_STHR12_REG
Shadow Receive/Transmit Buffer Register
0x50001164
UART2_SRBR_STHR13_REG
Shadow Receive/Transmit Buffer Register
0x50001168
UART2_SRBR_STHR14_REG
Shadow Receive/Transmit Buffer Register
0x5000116C
UART2_SRBR_STHR15_REG
Shadow Receive/Transmit Buffer Register
0x5000117C
UART2_USR_REG
UART Status register.
0x50001180
UART2_TFL_REG
Transmit FIFO Level
0x50001184
UART2_RFL_REG
Receive FIFO Level.
0x50001188
UART2_SRR_REG
Software Reset Register.
0x5000118C
UART2_SRTS_REG
Shadow Request to Send
0x50001190
UART2_SBCR_REG
Shadow Break Control Register
0x50001194
UART2_SDMAM_REG
Shadow DMA Mode
0x50001198
UART2_SFE_REG
Shadow FIFO Enable
0x5000119C
UART2_SRT_REG
Shadow RCVR Trigger
0x500011A0
UART2_STET_REG
Shadow TX Empty Trigger
0x500011A4
UART2_HTX_REG
Halt TX
0x500011F4
UART2_CPR_REG
Component Parameter Register
0x500011F8
UART2_UCV_REG
Component Version
0x500011FC
UART2_CTR_REG
Component Type Register
0x50001200
SPI_CTRL_REG
SPI control register 0
0x50001202
SPI_RX_TX_REG0
SPI RX/TX register0
0x50001204
SPI_RX_TX_REG1
SPI RX/TX register1
0x50001206
SPI_CLEAR_INT_REG
SPI clear interrupt register
0x50001208
SPI_CTRL_REG1
SPI control register 1
0x50001300
I2C_CON_REG
I2C Control Register
0x50001304
I2C_TAR_REG
I2C Target Address Register
Datasheet
CFR0011-120-01
Revision 3.4
21 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 5: Register Map
Address
Port
Description
0x50001308
I2C_SAR_REG
I2C Slave Address Register
0x50001310
I2C_DATA_CMD_REG
I2C Rx/Tx Data Buffer and Command Register
0x50001314
I2C_SS_SCL_HCNT_REG
Standard Speed I2C Clock SCL High Count Register
0x50001318
I2C_SS_SCL_LCNT_REG
Standard Speed I2C Clock SCL Low Count Register
0x5000131C
I2C_FS_SCL_HCNT_REG
Fast Speed I2C Clock SCL High Count Register
0x50001320
I2C_FS_SCL_LCNT_REG
Fast Speed I2C Clock SCL Low Count Register
0x5000132C
I2C_INTR_STAT_REG
I2C Interrupt Status Register
0x50001330
I2C_INTR_MASK_REG
I2C Interrupt Mask Register
0x50001334
I2C_RAW_INTR_STAT_REG
I2C Raw Interrupt Status Register
0x50001338
I2C_RX_TL_REG
I2C Receive FIFO Threshold Register
0x5000133C
I2C_TX_TL_REG
I2C Transmit FIFO Threshold Register
0x50001340
I2C_CLR_INTR_REG
Clear Combined and Individual Interrupt Register
0x50001344
I2C_CLR_RX_UNDER_REG
Clear RX_UNDER Interrupt Register
0x50001348
I2C_CLR_RX_OVER_REG
Clear RX_OVER Interrupt Register
0x5000134C
I2C_CLR_TX_OVER_REG
Clear TX_OVER Interrupt Register
0x50001350
I2C_CLR_RD_REQ_REG
Clear RD_REQ Interrupt Register
0x50001354
I2C_CLR_TX_ABRT_REG
Clear TX_ABRT Interrupt Register
0x50001358
I2C_CLR_RX_DONE_REG
Clear RX_DONE Interrupt Register
0x5000135C
I2C_CLR_ACTIVITY_REG
Clear ACTIVITY Interrupt Register
0x50001360
I2C_CLR_STOP_DET_REG
Clear STOP_DET Interrupt Register
0x50001364
I2C_CLR_START_DET_REG
Clear START_DET Interrupt Register
0x50001368
I2C_CLR_GEN_CALL_REG
Clear GEN_CALL Interrupt Register
0x5000136C
I2C_ENABLE_REG
I2C Enable Register
0x50001370
I2C_STATUS_REG
I2C Status Register
0x50001374
I2C_TXFLR_REG
I2C Transmit FIFO Level Register
0x50001378
I2C_RXFLR_REG
I2C Receive FIFO Level Register
0x5000137C
I2C_SDA_HOLD_REG
I2C SDA Hold Time Length Register
0x50001380
I2C_TX_ABRT_SOURCE_REG
I2C Transmit Abort Source Register
0x50001394
I2C_SDA_SETUP_REG
I2C SDA Setup Register
0x50001398
I2C_ACK_GENERAL_CALL_REG
I2C ACK General Call Register
0x5000139C
I2C_ENABLE_STATUS_REG
I2C Enable Status Register
0x500013A0
I2C_IC_FS_SPKLEN_REG
I2C SS and FS spike suppression limit Size
0x50001400
GPIO_IRQ0_IN_SEL_REG
GPIO interrupt selection for GPIO_IRQ0
0x50001402
GPIO_IRQ1_IN_SEL_REG
GPIO interrupt selection for GPIO_IRQ1
0x50001404
GPIO_IRQ2_IN_SEL_REG
GPIO interrupt selection for GPIO_IRQ2
0x50001406
GPIO_IRQ3_IN_SEL_REG
GPIO interrupt selection for GPIO_IRQ3
0x50001408
GPIO_IRQ4_IN_SEL_REG
GPIO interrupt selection for GPIO_IRQ4
0x5000140C
GPIO_DEBOUNCE_REG
debounce counter value for GPIO inputs
0x5000140E
GPIO_RESET_IRQ_REG
GPIO interrupt reset register
0x50001410
GPIO_INT_LEVEL_CTRL_REG
high or low level select for GPIO interrupts
0x50001412
KBRD_IRQ_IN_SEL0_REG
GPIO interrupt selection for KBRD_IRQ for P0
0x50001414
KBRD_IRQ_IN_SEL1_REG
GPIO interrupt selection for KBRD_IRQ for P1 and P2
0x50001416
KBRD_IRQ_IN_SEL2_REG
GPIO interrupt selection for KBRD_IRQ for P3
0x50001500
GP_ADC_CTRL_REG
General Purpose ADC Control Register
Datasheet
CFR0011-120-01
Revision 3.4
22 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 5: Register Map
Address
Port
Description
0x50001502
GP_ADC_CTRL2_REG
General Purpose ADC Second Control Register
0x50001504
GP_ADC_OFFP_REG
General Purpose ADC Positive Offset Register
0x50001506
GP_ADC_OFFN_REG
General Purpose ADC Negative Offset Register
0x50001508
GP_ADC_CLEAR_INT_REG
General Purpose ADC Clear Interrupt Register
0x5000150A
GP_ADC_RESULT_REG
General Purpose ADC Result Register
0x5000150C
GP_ADC_DELAY_REG
General Purpose ADC Delay Register
0x5000150E
GP_ADC_DELAY2_REG
General Purpose ADC Second Delay Register
0x50001600
CLK_REF_SEL_REG
Select clock for oscillator calibration
0x50001602
CLK_REF_CNT_REG
Count value for oscillator calibration
0x50001604
CLK_REF_VAL_L_REG
XTAL16M reference cycles, lower 16 bits
0x50001606
CLK_REF_VAL_H_REG
XTAL16M reference cycles, upper 16 bits
0x50003000
P0_DATA_REG
P0 Data input / output register
0x50003002
P0_SET_DATA_REG
P0 Set port pins register
0x50003004
P0_RESET_DATA_REG
P0 Reset port pins register
0x50003006
P00_MODE_REG
P00 Mode Register
0x50003008
P01_MODE_REG
P01 Mode Register
0x5000300A
P02_MODE_REG
P02 Mode Register
0x5000300C
P03_MODE_REG
P03 Mode Register
0x5000300E
P04_MODE_REG
P04 Mode Register
0x50003010
P05_MODE_REG
P05 Mode Register
0x50003012
P06_MODE_REG
P06 Mode Register
0x50003014
P07_MODE_REG
P07 Mode Register
0x50003020
P1_DATA_REG
P1 Data input / output register
0x50003022
P1_SET_DATA_REG
P1 Set port pins register
0x50003024
P1_RESET_DATA_REG
P1 Reset port pins register
0x50003026
P10_MODE_REG
P10 Mode Register
0x50003028
P11_MODE_REG
P11 Mode Register
0x5000302A
P12_MODE_REG
P12 Mode Register
0x5000302C
P13_MODE_REG
P13 Mode Register
0x5000302E
P14_MODE_REG
P14 Mode Register
0x50003030
P15_MODE_REG
P15 Mode Register
0x50003040
P2_DATA_REG
P2 Data input / output register
0x50003042
P2_SET_DATA_REG
P2 Set port pins register
0x50003044
P2_RESET_DATA_REG
P2 Reset port pins register
0x50003046
P20_MODE_REG
P20 Mode Register
0x50003048
P21_MODE_REG
P21 Mode Register
0x5000304A
P22_MODE_REG
P22 Mode Register
0x5000304C
P23_MODE_REG
P23 Mode Register
0x5000304E
P24_MODE_REG
P24 Mode Register
0x50003050
P25_MODE_REG
P25 Mode Register
0x50003052
P26_MODE_REG
P26 Mode Register
0x50003054
P27_MODE_REG
P27 Mode Register
0x50003056
P28_MODE_REG
P28 Mode Register
0x50003058
P29_MODE_REG
P29 Mode Register
Datasheet
CFR0011-120-01
Revision 3.4
23 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 5: Register Map
Address
Port
Description
0x50003070
P01_PADPWR_CTRL_REG
Ports 0 and 1 Output Power Control Register
0x50003072
P2_PADPWR_CTRL_REG
Port 2 Output Power Control Register
0x50003074
P3_PADPWR_CTRL_REG
Port 3 Output Power Control Register
0x50003080
P3_DATA_REG
P3 Data input / output register
0x50003082
P3_SET_DATA_REG
P3 Set port pins register
0x50003084
P3_RESET_DATA_REG
P3 Reset port pins register
0x50003086
P30_MODE_REG
P30 Mode Register
0x50003088
P31_MODE_REG
P31 Mode Register
0x5000308A
P32_MODE_REG
P32 Mode Register
0x5000308C
P33_MODE_REG
P33 Mode Register
0x5000308E
P34_MODE_REG
P34 Mode Register
0x50003090
P35_MODE_REG
P35 Mode Register
0x50003092
P36_MODE_REG
P36 Mode Register
0x50003094
P37_MODE_REG
P37 Mode Register
0x50003100
WATCHDOG_REG
Watchdog timer register.
0x50003102
WATCHDOG_CTRL_REG
Watchdog control register.
0x50003200
CHIP_ID1_REG
Chip identification register 1.
0x50003201
CHIP_ID2_REG
Chip identification register 2.
0x50003202
CHIP_ID3_REG
Chip identification register 3.
0x50003203
CHIP_SWC_REG
Software compatibility register.
0x50003204
CHIP_REVISION_REG
Chip revision register.
0x50003300
SET_FREEZE_REG
Controls freezing of various timers/counters.
0x50003302
RESET_FREEZE_REG
Controls unfreezing of various timers/counters.
0x50003304
DEBUG_REG
Various debug information register.
0x50003306
GP_STATUS_REG
General purpose system status register.
0x50003308
GP_CONTROL_REG
General purpose system control register.
0x50003400
TIMER0_CTRL_REG
Timer0 control register
0x50003402
TIMER0_ON_REG
Timer0 on control register
0x50003404
TIMER0_RELOAD_M_REG
16 bits reload value for Timer0
0x50003406
TIMER0_RELOAD_N_REG
16 bits reload value for Timer0
0x50003408
PWM2_DUTY_CYCLE
Duty Cycle for PWM2
0x5000340A
PWM3_DUTY_CYCLE
Duty Cycle for PWM3
0x5000340C
PWM4_DUTY_CYCLE
Duty Cycle for PWM4
0x5000340E
TRIPLE_PWM_FREQUENCY
Frequency for PWM 2,3 and 4
0x50003410
TRIPLE_PWM_CTRL_REG
PWM 2 3 4 Control
Table 6: OTPC_MODE_REG (0x40008000)
Bit
Mode
Symbol
Description
Reset
31:30
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
24 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 6: OTPC_MODE_REG (0x40008000)
Bit
Mode
Symbol
Description
Reset
29:28
R/W
OTPC_MODE_PRG_
PORT_MUX
Selects the source that is connected to the prg_port port of
the controller.
00 - {16'd0, BANDGAP_REG[15:0]}
01 - {RF_RSSI_COMP_CTRL_REG[15:0], 8'd0,
RFIO_CTRL1_REG{7:0]}
10 - {3'd0, RF_LNA_CTRL3_REG[4:0],
RF_LNA_CTRL2_REG[11:0], RF_LNA_CTRL1_REG[11:0]}
11 - {28'd0, RF_VCO_CTRL_REG[3:0]}
0x0
See OTPC_MODE_PRG_PORT_SEL about the use of the
prg_port
27:9
-
-
Reserved
0x0
8
R/W
OPTC_MODE_PRG_
FAST
Defines the timing that will be used for all the programming
activities (APROG, MPROG and TWR)
0 - Selects the normal timing
1 - Selects the fast timing
0
7
R/W
OTPC_MODE_PRG_
PORT_SEL
Selects an alternative data source for the programming of
the OTP macrocells, when the controller is configured in
APROG mode.
0 - The fifo will be used as the data source. The fifo will be
filled with a way defined by the register
OTPC_MODE_USE_DMA. The number of words that will be
programmed is defined by OTPC_NWORDS.
1 - Only one word will programmed. The value of the word is
contained in the prg_port port of the controller. The values of
the registers OTPC_MODE_USE_DMA, OTPC_NWORDS
and the contents of the FIFO will not be used.
0x0
6
R/W
OTPC_MODE_TWO
_CC_ACC
Defines the duration of each read from the OTP macrocells.
0 - Reads 16 bits of data every one clock cycle.
1 - Reads 16 bits of data every two clock cycles.
0x0
5
R/W
OTPC_MODE_FIFO
_FLUSH
Writing 1, removes any content from the FIFO. This bit
returns automatically to 0.
0x0
4
R/W
OTPC_MODE_USE_
DMA
Selects the use of the dma, when the controller is configured
in one of the modes: AREAD or APROG.
0 - DMAis not used. The data should be transfered from/to
controller through OTPC_FFPRT_REG
1 - DMA is used. Data transfers from/to controller are performed automatically. The AHB base address should be configured in OTPC_AHBADR_REG before the selection of the
mode.
If programming of the OTPC_MODE_REG is performed
through the serial interface,the OTPC_MODE_USE_DMA
will be set to 0 automatically.
If the controller is in APROG mode and the
OTPC_MODE_PRG_PORT_SEL is enabled, the dma will
stay inactive.
0x0
3
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
25 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 6: OTPC_MODE_REG (0x40008000)
Bit
Mode
Symbol
Description
Reset
2:0
R/W
OTPC_MODE_MOD
E
Defines the mode of operation of the OTPC controller. The
encoding of the modes is as follows:
000 - STBY mode
001 - MREAD mode
010 - MPROG mode
011 - AREAD mode
100 - APROG mode
101 - Test mode. Reserved
110 - Test mode. Reserved
111 - Test mode. Reserved
To manually move between modes, always return to STBY
mode first.
0x0
Table 7: OTPC_PCTRL_REG (0x40008004)
Bit
Mode
Symbol
Description
Reset
31:28
-
-
Reserved
0x0
27
R/W
OTPC_PCTRL_ENU
Enables the programming in the upper bank of the OTP.
0 - Programming sequence is not applied in the upper bank.
1 - Programming sequence is applied in the upper bank.
0x0
26
R/W
OTPC_PCTRL_BITU
Defines the value of the selected bit in the upper bank, after
the programming sequence.
0x0
25
R/W
OTPC_PCTRL_ENL
Enables the programming in the lower bank.
0 - The programming sequence is not applied in the lower
bank.
1 -The programming sequence is applied in the lower bank.
0x0
24
R/W
OTPC_PCTRL_BITL
Defines the value of the selected bit in the lower bank, after
the programming sequence.
0x0
23
R/W
OTPC_PCTRL_BSE
LU
Selects between the U1 and U0 byte for the programming
sequence in the upper bank.
0 - Program the U0 byte
1 - Program the U1 byte
0x0
22:20
R/W
OTPC_PCTRL_BAD
RU
Selects the bit inside the Ux (x=0,1) byte, which will be programmed in the upper bank.
0x0
19
R/W
OTPC_PCTRL_BSE
LL
Selects between the L1 and L0 byte for the programming
sequence in the lower bank.
0 - Program the L0 byte
1 - Program the L1 byte
0x0
18:16
R/W
OTPC_PCTRL_BAD
RL
Selects the bit inside the Lx (x=0,1) byte, which will be programmed in the lower bank.
0x0
15:13
-
-
Reserved
0x0
12:0
R/W
OTPC_PCTRL_WAD
DR
Defines the address of a 32 bits word {U1,L1,U0,L0} in the
macrocells, where one or two bits will be programmed.
There are two macrocell banks, with 8 bits each. Each bank
contribute with two memory positions for each 32 bits word.
The Ux, Lx represent the bytes of the upper and lower bank
respectively.
0x0
Table 8: OTPC_STAT_REG (0x40008008)
Bit
Mode
Symbol
Description
Reset
31:29
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
26 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 8: OTPC_STAT_REG (0x40008008)
Bit
Mode
Symbol
Description
Reset
28:16
R
OTPC_STAT_NWOR
DS
Contains the current value of the words to be processed.
0
15
R
OTPC_STAT_TERR_
U
Indicates the upper bank as the source of a test error. This
value is valid when OTPC_STAT_TERROR is valid.
0 - There is no test error in the upper bank
1 - A test error has occured in the upper bank
0x0
14
R
OTPC_STAT_TERR_
L
Indicates the lower bank as the source of a test error. The
value is valid when OTPC_STAT_TERROR is valid.
0 - There is no test error in the lower bank
1 - A test error has occured in the lower bank
0x0
13
R
OTPC_STAT_PERR_
U
Indicates the upper bank as the source of a programming
error. The value is valid when OTPC_STAT_PERROR is
valid.
0 - There is no programming error in the upper bank
1 - A programming error has occured in the upper bank
0x0
12
R
OTPC_STAT_PERR_
L
Indicates the lower bank as the source of a programming
error. The value is valid when OTPC_STAT_PERROR is
valid.
0 - There is no programming error in the lower bank
1 - A programming error has occured in the lower bank
0x0
11:8
R
OTPC_STAT_FWOR
DS
Indicates the number of words which contained in the fifo of
the controller.
0x0
7:5
-
-
Reserved
0x0
4
R
OTPC_STAT_ARDY
Monitors the progress of read or programming operations
while in the AREAD or APROG modes.
0 - The controller is busy while reading or programming
(AREAD or APROG modes).
1 - The controller is not busy in AREAD or APROG mode.
0x1
3
R
OTPC_STAT_TERR
OR
Indicates the result of a test sequence. Should be checked
after the end of a TBLANK, TDEC and TWR mode
(OTPC_STAT_TRDY= 1).
0 - The test sequence ends with no error.
1 - The test sequence has failed.
0x0
2
R
OTPC_STAT_TRDY
Indicates the state of a test mode. Should be used to monitor
the progress of the TBLANK, TDEC and TWR modes.
0 - The controller is busy. A test mode is in progress.
1 - There is no active test mode.
0x1
1
R
OTPC_STAT_PERR
OR
Indicates that an error has occurred during the bit-programming process.
0 - No error during the bit-programming process.
1 - The process of bit-programming failed.
When the controller is in MPROG mode, this bit should be
checked after the end of the programming process
(OTPC_STAT_PRDY= 1).
During APROG mode, the value of this field is normal to
change periodically. Upon finishing the operation in the
APROG mode (OTPC_STAT_ARDY= 1), this field indicates
if the programming has failed or ended succesfully.
0x0
0
R
OTPC_STAT_PRDY
Indicates the state of a bit-programming process.
0 - The controller is busy. A bit-programming is in progress
1 - The logic which performs bit-programming is idle.
When the controller is in MPROG mode, this bit should be
used to monitor the progress of a programming request.
During APROG mode, the value of this field it is normal to
changing periodically.
0x1
Datasheet
CFR0011-120-01
Revision 3.4
27 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 9: OTPC_AHBADR_REG (0x4000800C)
Bit
Mode
Symbol
Description
Reset
31:2
R/W
OTPC_AHBADR
Tthe AHB address used by the AHB master interface of the
controller (
bits [31:2]).
0x0
1:0
-
-
Reserved
0x0
Table 10: OTPC_CELADR_REG (0x40008010)
Bit
Mode
Symbol
Description
Reset
31:13
-
-
Reserved
0x0
12:0
R/W
OTPC_CELADR
Defines a word address inside the macrocell. Used in modes
AREAD and APROG and is automatically updated.
0x0
Table 11: OTPC_NWORDS_REG (0x40008014)
Bit
Mode
Symbol
Description
Reset
31:13
12:0
-
-
Reserved
0x0
R/W
OTPC_NWORDS
The number of words (minus one) for reading/programming
during the AREAD/APROG mode.
If in APROG mode, and the
OTPC_MODE_PRG_PORT_SEL is enabled (=1), this register will not be used and will stay unchanged.
During mirroring, this register reflects the current amount of
data that will be copied. It keeps its value until be written by
the software with a new value. The number of the words that
remaining to be processed by the controller is contained in
the field OTPC_STAT_NWORDS.
0x0
Table 12: OTPC_FFPRT_REG (0x40008018)
Bit
Mode
Symbol
Description
Reset
31:0
R/W
OTPC_FFPRT
Provides access to the fifo through an access port. Write this
register with the corresponding data, when the APROG
mode is selected and the DMA is disabled. Read from this
register the corresponding data, when the AREAD mode is
selected and the DMA is disabled.
Check OTPC_STAT_FWORDS register for data/space availability, before accessing the fifo.
0x0
Table 13: OTPC_FFRD_REG (0x4000801C)
Bit
Mode
Symbol
Description
Reset
31:0
R
OTPC_FFRD
Contains the value read from the fifo, after a read of the
OTPC_FFPRT_REG register.
0x0
Table 14: CLK_AMBA_REG (0x50000000)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R/W
OTP_ENABLE
Clock enable for OTP controller
0x0
6
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
28 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 14: CLK_AMBA_REG (0x50000000)
Bit
Mode
Symbol
Description
Reset
5:4
R/W
PCLK_DIV
APB interface clock (PCLK). Divider is cascaded with
HCLK_DIV. PCLK is HCLK divided by:
0x0: divide by 1
0x1: divide by 2
0x2: divide by 4
0x3: divide by 8
0x2
3:2
-
-
Reserved
0x0
1:0
R/W
HCLK_DIV
AHB interface and microprocessor clock (HCLK). HCLK is
source clock divided by:
0x0: divide by 1
0x1: divide by 2
0x2: divide by 4
0x3: divide by 8
0x2
Table 15: CLK_FREQ_TRIM_REG (0x50000002)
Bit
Mode
Symbol
Description
Reset
15:11
-
10:8
R/W
-
Reserved
0x0
COARSE_ADJ
Xtal frequency course trimming register.
0x0: lowest frequency
0x7: highest frequencyIncrement or decrement the binary
value with 1. Wait approximately 200 us to allow the adjustment to settle.
0x0
7:0
R/W
FINE_ADJ
Xtal frequency fine trimming register.
0x00: lowest frequency
0xFF: highest frequency
0x0
Table 16: CLK_PER_REG (0x50000004)
Bit
Mode
Symbol
Description
Reset
15
R/W
QUAD_ENABLE
Enable the Quadrature clock
0x0
14:12
-
-
Reserved
0x0
11
R/W
SPI_ENABLE
Enable SPI clock
0x0
10
-
-
Reserved
0x0
9:8
R/W
SPI_DIV
Division factor for SPI
0x0: divide by 1
0x1: divide by 2
0x2: divide by 4
0x3: divide by 8
0x0
7
R/W
UART1_ENABLE
Enable UART1 clock
0x0
6
R/W
UART2_ENABLE
Enable UART2 clock
0x0
5
R/W
I2C_ENABLE
Enable I2C clock
0x0
4
R/W
WAKEUPCT_ENABL
E
Enable Wakeup CaptureTimer clock
0x0
3
R/W
TMR_ENABLE
Enable TIMER0 and TIMER2 clock
0x0
2
-
-
Reserved
0x0
1:0
R/W
TMR_DIV
Division factor for TIMER0
0x0: divide by 1
0x1: divide by 2
0x2: divide by 4
0x3: divide by 8
0x0
Datasheet
CFR0011-120-01
Revision 3.4
29 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 17: CLK_RADIO_REG (0x50000008)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R/W
BLE_ENABLE
Enable the BLE core clocks
0x0
6
R/W
BLE_LP_RESET
Reset for the BLE LP timer
0x1
5:4
R/W
BLE_DIV
Division factor for BLE core blocks
0x0: divide by 1
0x1: divide by 2
0x2: divide by 4
0x3: divide by 8
The programmed frequency should not be lower than 8 MHz
and not faster than the programmed CPU clock frequency.
Refer also to BLE_CNTL2_REG[BLE_CLK_SEL].
0x0
3
R/W
RFCU_ENABLE
Enable the RF control Unit clock
0x0
2
-
-
Reserved
0x0
1:0
R/W
RFCU_DIV
Division factor for RF Control Unit
0x0: divide by 1
0x1: divide by 2
0x2: divide by 4
0x3: divide by 8
The programmed frequency must be exactly 8 MHz.
0x0
Table 18: CLK_CTRL_REG (0x5000000A)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R
RUNNING_AT_XTAL
16M
Indicates that the XTAL16M clock is used as clock, and may
not be switched off
0x1
6
R
RUNNING_AT_RC16
M
Indicates that the RC16M clock is used as clock
0x0
5
R
RUNNING_AT_32K
Indicates that either the RC32k or XTAL32k is being used as
clock
0x0
4
-
-
Reserved
0x0
3
R/W
XTAL16M_SPIKE_FL
T_DISABLE
Disable spikefilter in digital clock
0x0
2
R/W
XTAL16M_DISABLE
Setting this bit instantaneously disables the 16 MHz crystal
oscillator. Also, after sleep/wakeup cycle, the oscillator will
not be enabled. This bit may not be set to '1'when
"RUNNING_AT_XTAL16M is '1' to prevent deadlock. After
resetting this bit, wait for XTAL16_SETTLED or
XTAL16_TRIM_READY to become '1' before switching to
XTAL16 clock source.
0x0
1:0
R/W
SYS_CLK_SEL
Selects the clock source.
0x0: XTAL16M (check the XTAL16_SETTLED and
XTAL16_TRIM_READY bits!!)
0x1: RC16M
0x2/0x3: either RC32k or XTAL32k is used
0x0
Table 19: PMU_CTRL_REG (0x50000010)
Bit
Mode
Symbol
Description
Reset
15:12
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
30 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 19: PMU_CTRL_REG (0x50000010)
Bit
Mode
Symbol
Description
Reset
11:8
R/W
RETENTION_MODE
Select the retainability of the 4 retention RAM macros.
'1' is retainable, '0' is power gated.
(3) is RETRAM4
(2) is RETRAM3
(1) is RETRAM2
(0) is RETRAM1
0x0
7
R/W
FORCE_BOOST
Force the DCDC into boost mode at next wakeup.
Setting this bit reduces the deepsleep current.
FORCE_BOOST has highest priority.
When either FORCE_BOOST or FORCE_BUCK have been
written, these bits cannot be changed.
0x0
6
R/W
FORCE_BUCK
Force the DCDC into buck mode at next wakeup.
Setting this bit reduces the deepsleep current.
FORCE_BOOST has highest priority.
When either FORCE_BOOST or FORCE_BUCK have been
written, these bits cannot be changed.
0x0
5:4
R/W
OTP_COPY_DIV
Sets the HCLK division during OTP mirroring
0x0
2
R/W
RADIO_SLEEP
Put the digital part of the radio in powerdown
0x1
1
R/W
PERIPH_SLEEP
Put all peripherals (I2C, UART, SPI, ADC) in powerdown
0x1
0
R/W
RESET_ON_WAKEU
P
Perform a Hardware Reset after waking up. Booter will be
started.
0x0
Table 20: SYS_CTRL_REG (0x50000012)
Bit
Mode
Symbol
Description
Reset
15
W
SW_RESET
Writing a '1' to this bit will reset the device, except for:
SYS_CTRL_REG
CLK_FREQ_TRIM_REG
...
0x0
9
R/W
TIMEOUT_DISABLE
Disables timeout in Power statemachine. By default, the
statemachine continues if after 2 ms the blocks are not
started up. This can be read back from
ANA_STATUS_REG.
0x0
8
-
-
Reserved
0x0
7
R/W
DEBUGGER_ENABL
E
Enable the debugger. This bit is set by the booter according
to the OTP header. If not set, the SWDIO and SW_CLK can
be used as gpio ports.
0x0
6
R/W
OTPC_RESET_REQ
Reset request for the OTP controller.
0x0
5
R/W
PAD_LATCH_EN
Latches the control signals of the pads for state retention in
powerdown mode.
0: Control signals are retained
1: Latch is transparant, pad can be recontrolled
0x1
4
R/W
OTP_COPY
Enables OTP to SysRAM copy action after waking up
PD_SYS
0x0
3
R/W
CLK32_SOURCE
Sets the clock source of the 32 kHz clock
0 = RC-oscillator
1 = 32 kHz crystal oscillator
0x0
Datasheet
CFR0011-120-01
Revision 3.4
31 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 20: SYS_CTRL_REG (0x50000012)
Bit
Mode
Symbol
Description
Reset
2
R/W
RET_SYSRAM
Sets the development phase mode.
The PD_SYS is not actually power gated (SysRAM is
retained).
No copy action to SysRAM is done when the system wakes
up.
For emulating startup time, the OTP_COPY bit still needs to
be set.
0x0
1:0
R/W
REMAP_ADR0
Controls which memory is located at address 0x0000 for
execution.
0x0: ROM
0x1: OTP
0x2: SysRAM
0x3: RetRAM
0x0
Description
Reset
Table 21: SYS_STAT_REG (0x50000014)
Bit
Mode
Symbol
15:8
-
-
Reserved
0x0
7
R
XTAL16_SETTLED
Indicates that XTAL16 has had > 2 ms of settle time
0x0
6
R
XTAL16_TRIM_REA
DY
Indicates that XTAL trimming mechanism is ready, i.e. the
trimming equals CLK_FREQ_TRIM_REG.
0x1
5
R
DBG_IS_UP
Indicates that PD_DBG is functional
0x0
4
R
DBG_IS_DOWN
Indicates that PD_DBG is in power down
0x1
3
R
PER_IS_UP
Indicates that PD_PER is functional
0x0
2
R
PER_IS_DOWN
Indicates that PD_PER is in power down
0x1
1
R
RAD_IS_UP
Indicates that PD_RAD is functional
0x0
0
R
RAD_IS_DOWN
Indicates that PD_RAD is in power down
0x1
Table 22: TRIM_CTRL_REG (0x50000016)
Bit
Mode
Symbol
Description
Reset
7:4
R/W
TRIM_TIME
Defines the delay between XTAL16M enable and applying
the CLK_FREQ_TRIM_REG in steps of 250 us.
0x0: apply directly
0x1: wait between 0 and 250 us
0x2: wait between 250 us and 500 us
etc.
(Note 1)
0xA
3:0
R/W
SETTLE_TIME
Defines the delay between applying
CLK_FREQ_TRIM_REG and XTAL16_SETTLED in steps of
250 us.
0x0: XTAL16_SETTLED is set direcly
0x1: wait between 0 and 250 us
0x2: wait between 250 us and 500 us
etc.
0x2
Note 1:
The period duration of 250 us is derived by dividing the RC16M clock signal by 4000. Consequently, the period duration may vary over temperature.
Table 23: CLK_32K_REG (0x50000020)
Bit
Mode
Symbol
Description
Reset
15:13
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
32 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 23: CLK_32K_REG (0x50000020)
Bit
Mode
Symbol
Description
Reset
12
R/W
XTAL32K_DISABLE_
AMPREG
Setting this bit disables the amplitude regulation of the
XTAL32kHz oscillator.
Set this bit to '1' for an external clock applied at XTAL32Kp.
Keep this bit '0' with a crystal between XTAL32Kp and
XTAL32Km.
0x0
11:8
R/W
RC32K_TRIM
Controls the frequency of the RC32K oscillator.
0x0: lowest frequency
0x7: default
0xF: highest frequency
0x7
7
R/W
RC32K_ENABLE
Enables the 32 kHz RC oscillator
0x1
6:3
R/W
XTAL32K_CUR
Bias current for the 32kHz XTAL oscillator.
0x0: minimum
0x3: default
0xF: maximum
For each application there is an optimal setting for which the
startup behavior is optimal.
0x3
2:1
R/W
XTAL32K_RBIAS
Setting for the bias resistor of the 32 kHz XTAL oscillator.
0x0: maximum
0x3: minimum
Prefered setting will be provided by Dialog.
0x2
0
R/W
XTAL32K_ENABLE
Enables the 32 kHz XTAL oscillator
0x0
Table 24: CLK_16M_REG (0x50000022)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9
R/W
XTAL16_NOISE_FIL
T_ENABLE
Enables noise flter in 16 MHz crystal oscillator
0x0
8
R/W
XTAL16_BIAS_SH_E
NABLE
Enables Ibias sample/hold function in 16 MHz crystal oscillator. This bit should be set when the system wake up and
reset before entering deep or extended sleep mode.
0x0
7:5
R/W
XTAL16_CUR_SET
Bias current for the 16 MHz XTAL oscillator.
0x0: minimum
0x7: maximum
0x5
4:1
R/W
RC16M_TRIM
Controls the frequency of the RC16M oscillator.
0x0: lowest frequency
0xF: highest frequency
0x0
0
R/W
RC16M_ENABLE
Enables the 16 MHz RC oscillator
0x0
Table 25: CLK_RCX20K_REG (0x50000024)
Bit
Mode
Symbol
Description
Reset
12
R/W
RCX20K_SELECT
Selects RCX oscillator.
0 : RC32K oscillator
1: RCX oscillator
0
11
R/W
RCX20K_ENABLE
Enable the RCX oscillator
0
10
R/W
RCX20K_LOWF
Extra low frequency
0
9:8
R/W
RCX20K_BIAS
Bias control
1
7:4
R/W
RCX20K_NTC
Temperature control
7
Datasheet
CFR0011-120-01
Revision 3.4
33 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 25: CLK_RCX20K_REG (0x50000024)
Bit
Mode
Symbol
Description
Reset
3:0
R/W
RCX20K_TRIM
Controls the frequency of the RCX oscillator.
0x0: lowest frequency
0x7: default
0xF: highest frequency
8
Table 26: BANDGAP_REG (0x50000028)
Bit
Mode
Symbol
Description
Reset
15
-
-
Reserved
0x0
14
R/W
BGR_LOWPOWER
Test-mode, do not use.
It disables the bandgap core (voltages will continue for some
time, but will slowely drift away)
0x0
13:10
R/W
LDO_RET_TRIM
(Note 2)
0x0
9:5
R/W
BGR_ITRIM
Current trimming for bias
0x0
4:0
R/W
BGR_TRIM
Trim register for bandgap
0x0
Note 2:
0xF is the lowest voltage, but is too low for reliable startup at high temperature in combination with extended sleep. 0xA is 100 mV higher
and considered to be the lowest value which is safe to use. 0x0 or 0x1 is again 100 mV higher and 0x0 is the reset value. 0x4 is the maximum voltage.
Table 27: ANA_STATUS_REG (0x5000002A)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9
R
BOOST_SELECTED
Indicates that DCDC is in boost mode
0x0
8
-
-
Reserved
0x0
7
R
BANDGAP_OK
Indicates that BANDGAP is OK
0x1
6
R
BOOST_VBAT_OK
Indicates that VBAT is above threshold while in BOOST converter mode.
0x0
5
R
LDO_ANA_OK
Indicates that LDO_ANA is in regulation. This LDO is used
for the general-purpose ADC only
0x0
4
R
LDO_VDD_OK
Indicates that LDO_VDD is in regulation
0x1
3
R
LDO_OTP_OK
Indicates that LDO_OTP is in regulation
0x0
2
R
VDCDC_OK
Indicates that VDCDC is above threshold.
0x0
1
R
VBAT1V_OK
Indicates that VBAT1V is above threshold.
0x0
0
R
VBAT1V_AVAILABLE
Indicates that VBAT1V is available.
0x0
Table 28: WKUP_CTRL_REG (0x50000100)
Bit
Mode
Symbol
Description
Reset
15:14
7
-
-
Reserved
0x0
R/W
WKUP_ENABLE_IR
Q
0: no interrupt will be enabled
1: if the event counter reaches the value set by
WKUP_COMPARE_REG an IRQ will be generated
0x0
6
R/W
WKUP_SFT_KEYHIT
0: no effect
1: emulate key hit. The event counter will increment by 1
(after debouncing if enabled). First make this bit 0 before any
new key hit can be sensed.
0x0
5:0
R/W
WKUP_DEB_VALUE
Keyboard debounce time (N*1 ms with N = 1 to 63).
0x0: no debouncing
0x1 to 0x3F: 1 ms to 63 ms debounce time
0x0
Datasheet
CFR0011-120-01
Revision 3.4
34 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 29: WKUP_COMPARE_REG (0x50000102)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
COMPARE
The number of events that have to be counted before the
wakeup interrupt will be given
0x0
Table 30: WKUP_RESET_IRQ_REG (0x50000104)
Bit
Mode
Symbol
Description
Reset
15:0
W
WKUP_IRQ_RST
writing any value to this register will reset the interrupt. reading always returns 0.
0x0
Table 31: WKUP_COUNTER_REG (0x50000106)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R
EVENT_VALUE
This value represents the number of events that have been
counted so far. It will be reset by resetting the interrupt.
0x0
Table 32: WKUP_RESET_CNTR_REG (0x50000108)
Bit
Mode
Symbol
Description
Reset
15:0
W
WKUP_CNTR_RST
writing any value to this register will reset the event counter
0x0
Table 33: WKUP_SELECT_P0_REG (0x5000010A)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
WKUP_SELECT_P0
0: input P0x is not enabled for wakeup event counter
1: input P0x is enabled for wakeup event counter
0x0
Table 34: WKUP_SELECT_P1_REG (0x5000010C)
Bit
Mode
Symbol
Description
Reset
5:0
R/W
WKUP_SELECT_P1
0: input P1x is not enabled for wakeup event counter
1: input P1x is enabled for wakeup event counter
0x0
Table 35: WKUP_SELECT_P2_REG (0x5000010E)
Bit
Mode
Symbol
Description
Reset
9:0
R/W
WKUP_SELECT_P2
0: input P2x is not enabled for wakeup event counter
1: input P2x is enabled for wakeup event counter
0x0
Table 36: WKUP_SELECT_P3_REG (0x50000110)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
WKUP_SELECT_P3
0: input P3x is not enabled for wakeup event counter
1: input P3x is enabled for wakeup event counter
0x0
Datasheet
CFR0011-120-01
Revision 3.4
35 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 37: WKUP_POL_P0_REG (0x50000112)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
WKUP_POL_P0
0: enabled input P0x will increment the event counter if that
input goes high
1: enabled input P0x will increment the event counter if that
input goes low
0x0
Table 38: WKUP_POL_P1_REG (0x50000114)
Bit
Mode
Symbol
Description
Reset
5:0
R/W
WKUP_POL_P1
0: enabled input P1x will increment the event counter if that
input goes high
1: enabled input P1x will increment the event counter if that
input goes low
0x0
Table 39: WKUP_POL_P2_REG (0x50000116)
Bit
Mode
Symbol
Description
Reset
9:0
R/W
WKUP_POL_P2
0: enabled input P2x will increment the event counter if that
input goes high
1: enabled input P2x will increment the event counter if that
input goes low
0x0
Table 40: WKUP_POL_P3_REG (0x50000118)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
WKUP_POL_P3
0: enabled input P3x will increment the event counter if that
input goes high
1: enabled input P3x will increment the event counter if that
input goes low
0x0
Table 41: QDEC_CTRL_REG (0x50000200)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:3
R/W
QD_IRQ_THRES
The number of events on either counter (X or Y) that need to
be reached before an interrupt is generated. If 0 is written,
then threshold is considered to be 1.
0x2
2
R
QD_IRQ_STATUS
Interrupt Status. If 1 an interrupt has occured.
0x0
1
R/W
QD_IRQ_CLR
Writing 1 to this bit clears the interrupt. This bit is autocleared
0x0
0
R/W
QD_IRQ_MASK
0: interrupt is masked
1: interrupt is enabled
0x0
Table 42: QDEC_XCNT_REG (0x50000202)
Bit
Mode
Symbol
Description
Reset
15:0
R
X_COUNTER
Contains a signed value of the events. Zero when channel is
disabled
0x0
Datasheet
CFR0011-120-01
Revision 3.4
36 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 43: QDEC_YCNT_REG (0x50000204)
Bit
Mode
Symbol
Description
Reset
15:0
R
Y_COUNTER
Contains a signed value of the events. Zero when channel is
disabled
0x0
Table 44: QDEC_CLOCKDIV_REG (0x50000206)
Bit
Mode
Symbol
Description
Reset
9:0
R/W
CLOCK_DIVIDER
Contains the number of the input clock cycles minus one,
that are required to generate one logic clock cycle.
0x0
Table 45: QDEC_CTRL2_REG (0x50000208)
Bit
Mode
Symbol
Description
Reset
15:12
-
-
Reserved
0
11:8
R/W
CHZ_PORT_SEL
Defines which GPIOs are mapped on Channel Z
0: none
1: P0[0] -> CHZ_A, P0[1] -> CHZ_B
2: P0[2] -> CHZ_A, P0[3] -> CHZ_B
3: P0[4] -> CHZ_A, P0[5] -> CHZ_B
4: P0[6] -> CHZ_A, P0[7] -> CHZ_B
5: P1[0] -> CHZ_A, P1[1] -> CHZ_B
6: P1[2] -> CHZ_A, P1[3] -> CHZ_B
7: P2[3] -> CHZ_A, P2[4] -> CHZ_B
8: P2[5] -> CHZ_A, P2[6] -> CHZ_B
9: P2[7] -> CHZ_A, P2[8] -> CHZ_B
10: P2[9] -> CHZ_A, P2[0] -> CHZ_B
11..15: None
0
7:4
R/W
CHY_PORT_SEL
Defines which GPIOs are mapped on Channel Y
0: none
1: P0[0] -> CHY_A, P0[1] -> CHY_B
2: P0[2] -> CHY_A, P0[3] -> CHY_B
3: P0[4] -> CHY_A, P0[5] -> CHY_B
4: P0[6] -> CHY_A, P0[7] -> CHY_B
5: P1[0] -> CHY_A, P1[1] -> CHY_B
6: P1[2] -> CHY_A, P1[3] -> CHY_B
7: P2[3] -> CHY_A, P2[4] -> CHY_B
8: P2[5] -> CHY_A, P2[6] -> CHY_B
9: P2[7] -> CHY_A, P2[8] -> CHY_B
10: P2[9] -> CHY_A, P2[0] -> CHY_B
11..15: None
0
3:0
R/W
CHX_PORT_SEL
Defines which GPIOs are mapped on Channel X
0: none
1: P0[0] -> CHX_A, P0[1] -> CHX_B
2: P0[2] -> CHX_A, P0[3] -> CHX_B
3: P0[4] -> CHX_A, P0[5] -> CHX_B
4: P0[6] -> CHX_A, P0[7] -> CHX_B
5: P1[0] -> CHX_A, P1[1] -> CHX_B
6: P1[2] -> CHX_A, P1[3] -> CHX_B
7: P2[3] -> CHX_A, P2[4] -> CHX_B
8: P2[5] -> CHX_A, P2[6] -> CHX_B
9: P2[7] -> CHX_A, P2[8] -> CHX_B
10: P2[9] -> CHX_A, P2[0] -> CHX_B
11..15: None
0
Datasheet
CFR0011-120-01
Revision 3.4
37 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 46: QDEC_ZCNT_REG (0x5000020A)
Bit
Mode
Symbol
Description
Reset
15:0
R
Z_COUNTER
Contains a signed value of the events. Zero when channel is
disabled
0
Table 47: UART_RBR_THR_DLL_REG (0x50001000)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
RBR_THR_DLL
Receive Buffer Register: This register contains the data byte
received on the serial input port (sin) in UART mode or the
serial infrared input (sir_in) in infrared mode. The data in this
register is valid only if the Data Ready (DR) bit in the Line
status Register (LSR) is set. If FIFOs are disabled (FCR[0]
set to zero), the data in the RBR must be read before the
next data arrives, otherwise it will be overwritten, resulting in
an overrun error. If FIFOs are enabled (FCR[0] set to one),
this register accesses the head of the receive FIFO. If the
receive FIFO is full and this register is not read before the
next data character arrives, then the data already in the
FIFO will be preserved but any incoming data will be lost. An
overrun error will also occur. Transmit Holding Register: This
register contains data to be transmitted on the serial output
port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost. Divisor Latch (Low): This register makes up the lower 8bits of a 16-bit, read/write, Divisor Latch register that contains the baud rate divisor for the UART. This register may
only be accessed when the DLAB bit (LCR[7]) is set. The
output baud rate is equal to the serial clock (sclk) frequency
divided by sixteen times the value of the baud rate divisor, as
follows: baud rate = (serial clock freq) / (16 * divisor) Note
that with the Divisor Latch Registers (DLL and DLH) set to
zero, the baud clock is disabled and no serial communications will occur. Also, once the DLL is set, at least 8 clock
cycles of the slowest DW_apb_uart clock should be allowed
to pass before transmitting or receiving data.
0x0
Table 48: UART_IER_DLH_REG (0x50001004)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R/W
PTIME_DLH7
Interrupt Enable Register: PTIME, Programmable THRE
Interrupt Mode Enable. This is used to enable/disable the
generation of THRE Interrupt. 0 = disabled 1 = enabled Divisor Latch (High): Bit[7] of the 8 bit DLH register.
0x0
6:4
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
38 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 48: UART_IER_DLH_REG (0x50001004)
Bit
Mode
Symbol
Description
Reset
3
R/W
EDSSI_DLH3
Interrupt Enable Register: EDSSI, Enable Modem Status
Interrupt. This is used to enable/disable the generation of
Modem Status Interrupt. This is the fourth highest priority
interrupt. 0 = disabled 1 = enabled Divisor Latch (High):
Bit[3] of the 8 bit DLH register
0x0
2
R/W
ELSI_DHL2
Interrupt Enable Register: ELSI, Enable Receiver Line Status Interrupt. This is used to enable/disable the generation of
Receiver Line Status Interrupt. This is the highest priority
interrupt. 0 = disabled 1 = enabled Divisor Latch (High):
Bit[2] of the 8 bit DLH register.
0x0
1
R/W
ETBEI_DLH1
Interrupt Enable Register: ETBEI, Enable Transmit Holding
Register Empty Interrupt. This is used to enable/disable the
generation of Transmitter Holding Register Empty Interrupt.
This is the third highest priority interrupt. 0 = disabled 1 =
enabled Divisor Latch (High): Bit[1] of the 8 bit DLH register.
0x0
0
R/W
ERBFI_DLH0
Interrupt Enable Register: ERBFI, Enable Received Data
Available Interrupt. This is used to enable/disable the generation of Received Data Available Interrupt and the Character
Timeout Interrupt (if in FIFO mode and FIFO's enabled).
These are the second highest priority interrupts. 0 = disabled
1 = enabled Divisor Latch (High): Bit[0] of the 8 bit DLH register.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
39 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 49: UART_IIR_FCR_REG (0x50001008)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IIR_FCR
Interrupt Identification Register, reading this register; FIFO
Control Register, writing to this register. Interrupt Identification Register: Bits[7:6], FIFO's Enabled (or FIFOSE): This is
used to indicate whether the FIFO's are enabled or disabled.
00 = disabled. 11 = enabled. Bits[3:0], Interrupt ID (or IID):
This indicates the highest priority pending interrupt which
can be one of the following types: 0000 = modem status.
0001 = no interrupt pending. 0010 = THR empty. 0100 =
received data available. 0110 = receiver line status. 0111 =
busy detect. 1100 = character timeout. Bits[7:6], RCVR Trigger (or RT):. This is used to select the trigger level in the
receiver FIFO at which the Received Data Available Interrupt
will be generated. In auto flow control mode it is used to
determine when the rts_n signal will be de-asserted. It also
determines when the dma_rx_req_n signal will be asserted
when in certain modes of operation. The following trigger
levels are supported: 00 = 1 character in the FIFO 01 = FIFO
1/4 full 10 = FIFO 1/2 full 11 = FIFO 2 less than full Bits[5:4],
TX Empty Trigger (or TET): This is used to select the empty
threshold level at which the THRE Interrupts will be generated when the mode is active. It also determines when the
dma_tx_req_n signal will be asserted when in certain modes
of operation. The following trigger levels are supported: 00 =
FIFO empty 01 = 2 characters in the FIFO 10 = FIFO 1/4 full
11 = FIFO 1/2 full Bit[3], DMA Mode (or DMAM): This determines the DMA signalling mode used for the dma_tx_req_n
and dma_rx_req_n output signals. 0 = mode 0 1 = mode 1
Bit[2], XMIT FIFO Reset (or XFIFOR): This resets the control
portion of the transmit FIFO and treats the FIFO as empty.
Note that this bit is 'self-clearing' and it is not necessary to
clear this bit. Bit[1], RCVR FIFO Reset (or RFIFOR): This
resets the control portion of the receive FIFO and treats the
FIFO as empty. Note that this bit is 'self-clearing' and it is not
necessary to clear this bit. Bit[0], FIFO Enable (or FIFOE):
This enables/disables the transmit (XMIT) and receive
(RCVR) FIFO's. Whenever the value of this bit is changed
both the XMIT and RCVR controller portion of FIFO's will be
reset.
0x0
Table 50: UART_LCR_REG (0x5000100C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R/W
UART_DLAB
Divisor Latch Access Bit.
This bit is used to enable reading and writing of the Divisor
Latch register (DLL and DLH) to set the baud rate of the
UART.
This bit must be cleared after initial baud rate setup in order
to access other registers.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
40 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 50: UART_LCR_REG (0x5000100C)
Bit
Mode
Symbol
Description
Reset
6
R/W
UART_BC
Break Control Bit.
This is used to cause a break condition to be transmitted to
the receiving device. If set to one the serial output is forced
to the spacing (logic 0) state. When not in Loopback Mode,
as determined by MCR[4], the sout line is forced low until the
Break bit is cleared. If active (MCR[6] set to one) the
sir_out_n line is continuously pulsed. When in Loopback
Mode, the break condition is internally looped back to the
receiver and the sir_out_n line is forced low.
0x0
5
-
-
Reserved
0x0
4
R/W
UART_EPS
Even Parity Select.
This is used to select between even and odd parity, when
parity is enabled (PEN set to one). If set to one, an even
number of logic 1s is transmitted or checked. If set to zero,
an odd number of logic 1s is transmitted or checked.
0x0
3
R/W
UART_PEN
Parity Enable.
This bit is used to enable and disable parity generation and
detection in transmitted and received serial character
respectively.
0 = parity disabled
1 = parity enabled
0x0
2
R/W
UART_STOP
Number of stop bits.
This is used to select the number of stop bits per character
that the peripheral transmits and receives. If set to zero, one
stop bit is transmitted in the serial data.
If set to one and the data bits are set to 5 (LCR[1:0] set to
zero) one and a half stop bits is transmitted. Otherwise, two
stop bits are transmitted. Note that regardless of the number
of stop bits selected, the receiver checks only the first stop
bit.
0 = 1 stop bit
1 = 1.5 stop bits when DLS (LCR[1:0]) is zero, else 2 stop bit
0x0
1:0
R/W
UART_DLS
Data Length Select.
This is used to select the number of data bits per character
that the peripheral transmits and receives. The number of bit
that may be selected areas follows:
00 = 5 bits
01 = 6 bits
10 = 7 bits
11 = 8 bits
0x0
Table 51: UART_MCR_REG (0x50001010)
Bit
Mode
Symbol
Description
Reset
15:7
-
-
Reserved
0x0
6
R/W
UART_SIRE
SIR Mode Enable.
This is used to enable/disable the IrDA SIR Mode features
as described in "IrDA 1.0 SIR Protocol" on page 53.
0 = IrDA SIR Mode disabled
1 = IrDA SIR Mode enabled
0x0
5
R/W
UART_AFCE
Auto Flow Control Enable.
When FIFOs are enabled and the Auto Flow Control Enable
(AFCE) bit is set, hardware Auto Flow Control is enabled via
CTS and RTS.
0 = Auto Flow Control Mode disabled
1 = Auto Flow Control Mode enabled
0x0
Datasheet
CFR0011-120-01
Revision 3.4
41 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 51: UART_MCR_REG (0x50001010)
Bit
Mode
Symbol
Description
Reset
4
R/W
UART_LB
LoopBack Bit.
This is used to put the UART into a diagnostic mode for test
purposes.
If operating in UART mode (SIR_MODE not active, MCR[6]
set to zero), data on the sout line is held high, while serial
data output is looped back to the sin line, internally. In this
mode all the interrupts are fully functional. Also, in loopback
mode, the modem control inputs (dsr_n, cts_n, ri_n, dcd_n)
are disconnected and the modem control outputs (dtr_n,
rts_n, out1_n, out2_n) are looped back to the inputs, internally.
If operating in infrared mode (SIR_MODE active, MCR[6] set
to one), data on the sir_out_n line is held low, while serial
data output is inverted and looped back to the sir_in line.
0x0
3
R/W
UART_OUT2
OUT2.
This is used to directly control the user-designated Output2
(out2_n) output. The value written to this location is inverted
and driven out on out2_n, that is:
0 = out2_n de-asserted (logic 1)
1 = out2_n asserted (logic 0)
Note that in Loopback mode (MCR[4] set to one), the out2_n
output is held inactive high while the value of this location is
internally looped back to an input.
0x0
2
R/W
UART_OUT1
OUT1.
This is used to directly control the user-designated Output1
(out1_n) output. The value written to this location is inverted
and driven out on out1_n, that is:
0 = out1_n de-asserted (logic 1)
1 = out1_n asserted (logic 0)
Note that in Loopback mode (MCR[4] set to one), the out1_n
output is held inactive high while the value of this location is
internally looped back to an input.
0x0
1
R/W
UART_RTS
Request to Send.
This is used to directly control the Request to Send (rts_n)
output. The Request To Send (rts_n) output is used to inform
the modem or data set that the UART is ready to exchange
data.
When Auto Flow Control is disabled (MCR[5] set to zero),
the rts_n signal is set low by programming MCR[1] (RTS) to
a high. When Auto Flow Control is enabled (MCR[5] set to
one) and FIFOs are enabled (FCR[0] set to one), the rts_n
output is controlled in the same way, but is also gated with
the receiver FIFO threshold trigger (rts_n is inactive high
when above the threshold). The rts_n signal is de-asserted
when MCR[1] is set low.
Note that in Loopback mode (MCR[4] set to one), the rts_n
output is held inactive (high) while the value of this location is
internally looped back to an input.
0x0
0
-
-
Reserved
0x0
Table 52: UART_LSR_REG (0x50001014)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
42 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 52: UART_LSR_REG (0x50001014)
Bit
Mode
Symbol
Description
Reset
7
R
UART_RFE
Receiver FIFO Error bit.
This bit is only relevant when FIFOs are enabled (FCR[0] set
to one). This is used to indicate if there is at least one parity
error, framing error, or break indication in the FIFO.
0 = no error in RX FIFO
1 = error in RX FIFO
This bit is cleared when the LSR is read and the character
with the error is at the top of the receiver FIFO and there are
no subsequent errors in the FIFO.
0x0
6
R
UART_TEMT
Transmitter Empty bit.
If FIFOs enabled (FCR[0] set to one), this bit is set whenever
the Transmitter Shift Register and the FIFO are both empty.
If FIFOs are disabled, this bit is set whenever the Transmitter
Holding Register and the Transmitter Shift Register are both
empty.
0x1
5
R
UART_THRE
Transmit Holding Register Empty bit.
If THRE mode is disabled (IER[7] set to zero) and regardless
of FIFO's being implemented/enabled or not, this bit indicates that the THR or TX FIFO is empty.
This bit is set whenever data is transferred from the THR or
TX FIFO to the transmitter shift register and no new data has
been written to the THR or TX FIFO. This also causes a
THRE Interrupt to occur, if the THRE Interrupt is enabled. If
both modes are active (IER[7] set to one and FCR[0] set to
one respectively), the functionality is switched to indicate the
transmitter FIFO is full, and no longer controls THRE interrupts, which are then controlled by the FCR[5:4] threshold
setting.
0x1
4
R
UART_B1
Break Interrupt bit.
This is used to indicate the detection of a break sequence on
the serial input data.
If in UART mode (SIR_MODE == Disabled), it is set whenever the serial input, sin, is held in a logic '0' state for longer
than the sum of start time + data bits + parity + stop bits.
If in infrared mode (SIR_MODE == Enabled), it is set whenever the serial input, sir_in, is continuously pulsed to logic '0'
for longer than the sum of start time + data bits + parity +
stop bits. A break condition on serial input causes one and
only one character, consisting of all zeros, to be received by
the UART.
In the FIFO mode, the character associated with the break
condition is carried through the FIFO and is revealed when
the character is at the top of the FIFO.
Reading the LSR clears the BI bit. In the non-FIFO mode,
the BI indication occurs immediately and persists until the
LSR is read.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
43 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 52: UART_LSR_REG (0x50001014)
Bit
Mode
Symbol
Description
Reset
3
R
UART_FE
Framing Error bit.
This is used to indicate the occurrence of a framing error in
the receiver. A framing error occurs when the receiver does
not detect a valid STOP bit in the received data.
In the FIFO mode, since the framing error is associated with
a character received, it is revealed when the character with
the framing error is at the top of the FIFO.
When a framing error occurs, the UART tries to resynchronize. It does this by assuming that the error was due to the
start bit of the next character and then continues receiving
the other bit i.e. data, and/or parity and stop. It should be
noted that the Framing Error (FE) bit (LSR[3]) is set if a
break interrupt has occurred, as indicated by Break Interrupt
(BI) bit (LSR[4]).
0 = no framing error
1 = framing error
Reading the LSR clears the FE bit.
0x0
2
R
UART_PE
Parity Error bit.
This is used to indicate the occurrence of a parity error in the
receiver if the Parity Enable (PEN) bit (LCR[3]) is set.
In the FIFO mode, since the parity error is associated with a
character received, it is revealed when the character with the
parity error arrives at the top of the FIFO.
It should be noted that the Parity Error (PE) bit (LSR[2]) is
set if a break interrupt has occurred, as indicated by Break
Interrupt (BI) bit (LSR[4]).
0 = no parity error
1 = parity error
Reading the LSR clears the PE bit.
0x0
1
R
UART_OE
Overrun error bit.
This is used to indicate the occurrence of an overrun error.
This occurs if a new data character was received before the
previous data was read.
In the non-FIFO mode, the OE bit is set when a new character arrives in the receiver before the previous character was
read from the RBR. When this happens, the data in the RBR
is overwritten. In the FIFO mode, an overrun error occurs
when the FIFO is full and a new character arrives at the
receiver. The data in the FIFO is retained and the data in the
receive shift register is lost.
0 = no overrun error
1 = overrun error
Reading the LSR clears the OE bit.
0x0
0
R
UART_DR
Data Ready bit.
This is used to indicate that the receiver contains at least
one character in the RBR or the receiver FIFO.
0 = no data ready
1 = data ready
This bit is cleared when the RBR is read in non-FIFO mode,
or when the receiver FIFO is empty, in FIFO mode.
0x0
Table 53: UART_MSR_REG (0x50001018)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
44 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 53: UART_MSR_REG (0x50001018)
Bit
Mode
Symbol
Description
Reset
7
R
UART_DCD
Data Carrier Detect.
This is used to indicate the current state of the modem control line dcd_n. This bit is the complement of dcd_n. When
the Data Carrier Detect input (dcd_n) is asserted it is an indication that the carrier has been detected by the modem or
data set.
0 = dcd_n input is de-asserted (logic 1)
1 = dcd_n input is asserted (logic 0)
In Loopback Mode (MCR[4] set to one), DCD is the same as
MCR[3] (Out2).
0x0
6
R
UART_R1
Ring Indicator.
This is used to indicate the current state of the modem control line ri_n. This bit is the complement of ri_n. When the
Ring Indicator input (ri_n) is asserted it is an indication that a
telephone ringing signal has been received by the modem or
data set.
0 = ri_n input is de-asserted (logic 1)
1 = ri_n input is asserted (logic 0)
In Loopback Mode (MCR[4] set to one), RI is the same as
MCR[2] (Out1).
0x0
5
-
-
Reserved
0x0
4
R
UART_CTS
Clear to Send.
This is used to indicate the current state of the modem control line cts_n. This bit is the complement of cts_n. When the
Clear to Send input (cts_n) is asserted it is an indication that
the modem or data set is ready to exchange data with the
UART Ctrl.
0 = cts_n input is de-asserted (logic 1)
1 = cts_n input is asserted (logic 0)
In Loopback Mode (MCR[4] = 1), CTS is the same as
MCR[1] (RTS).
0x0
3
R
UART_DDCD
Delta Data Carrier Detect.
This is used to indicate that the modem control line dcd_n
has changed since the last time the MSR was read.
0 = no change on dcd_n since last read of MSR
1 = change on dcd_n since last read of MSR
Reading the MSR clears the DDCD bit. In Loopback Mode
(MCR[4] = 1), DDCD reflects changes on MCR[3] (Out2).
Note, if the DDCD bit is not set and the dcd_n signal is
asserted (low) and a reset occurs (software or otherwise),
then the DDCD bit is set when the reset is removed if the
dcd_n signal remains asserted.
0x0
2
R
UART_TERI
Trailing Edge of Ring Indicator.
This is used to indicate that a change on the input ri_n (from
an active-low to an inactive-high state) has occurred since
the last time the MSR was read.
0 = no change on ri_n since last read of MSR
1 = change on ri_n since last read of MSR
Reading the MSR clears the TERI bit. In Loopback Mode
(MCR[4] = 1), TERI reflects when MCR[2] (Out1) has
changed state from a high to a low.
0x0
1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
45 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 53: UART_MSR_REG (0x50001018)
Bit
Mode
Symbol
Description
Reset
0
R
UART_DCTS
Delta Clear to Send.
This is used to indicate that the modem control line cts_n
has changed since the last time the MSR was read.
0 = no change on cts_n since last read of MSR
1 = change on cts_n since last read of MSR
Reading the MSR clears the DCTS bit. In Loopback Mode
(MCR[4] = 1), DCTS reflects changes on MCR[1] (RTS).
Note, if the DCTS bit is not set and the cts_n signal is
asserted (low) and a reset occurs (software or otherwise),
then the DCTS bit is set when the reset is removed if the
cts_n signal remains asserted.
0x0
Table 54: UART_SCR_REG (0x5000101C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
UART_SCRATCH_P
AD
This register is for programmers to use as a temporary storage space. It has no defined purpose in the UART Ctrl.
0x0
Table 55: UART_LPDLL_REG (0x50001020)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
UART_LPDLL
This register makes up the lower 8-bits of a 16-bit, read/
write, Low Power Divisor Latch register that contains the
baud rate divisor for the UART, which must give a baud rate
of 115.2K. This is required for SIR Low Power (minimum
pulse width) detection at the receiver. This register may be
accessed only when the DLAB bit (LCR[7]) is set.
The output low-power baud rate is equal to the serial clock
(sclk) frequency divided by sixteen times the value of the
baud rate divisor, as follows:
Low power baud rate = (serial clock frequency)/(16* divisor)
Therefore, a divisor must be selected to give a baud rate of
115.2K.
NOTE: When the Low Power Divisor Latch registers (LPDLL
and LPDLH) are set to 0, the low-power baud clock is disabled and no low-power pulse detection (or any pulse detection) occurs at the receiver. Also, once the LPDLL is set, at
least eight clock cycles of the slowest UART Ctrl clock
should be allowed to pass before transmitting or receiving
data.
0x0
Table 56: UART_LPDLH_REG (0x50001024)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
46 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 56: UART_LPDLH_REG (0x50001024)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
UART_LPDLH
This register makes up the upper 8-bits of a 16-bit, read/
write, Low Power Divisor Latch register that contains the
baud rate divisor for the UART, which must give a baud rate
of 115.2K. This is required for SIR Low Power (minimum
pulse width) detection at the receiver. This register may be
accessed only when the DLAB bit (LCR[7]) is set.
The output low-power baud rate is equal to the serial clock
(sclk) frequency divided by sixteen times the value of the
baud rate divisor, as follows:
Low power baud rate = (serial clock frequency)/(16* divisor)
Therefore, a divisor must be selected to give a baud rate of
115.2K.
NOTE: When the Low Power Divisor Latch registers (LPDLL
and LPDLH) are set to 0, the low-power baud clock is disabled and no low-power pulse detection (or any pulse detection) occurs at the receiver. Also, once the LPDLH is set, at
least eight clock cycles of the slowest UART Ctrl clock
should be allowed to pass before transmitting or receiving
data.
0x0
Table 57: UART_SRBR_STHR0_REG (0x50001030)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
47 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 58: UART_SRBR_STHR1_REG (0x50001034)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 59: UART_SRBR_STHR2_REG (0x50001038)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
48 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 59: UART_SRBR_STHR2_REG (0x50001038)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 60: UART_SRBR_STHR3_REG (0x5000103C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
49 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 60: UART_SRBR_STHR3_REG (0x5000103C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 61: UART_SRBR_STHR4_REG (0x50001040)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
50 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 61: UART_SRBR_STHR4_REG (0x50001040)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 62: UART_SRBR_STHR5_REG (0x50001044)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
51 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 62: UART_SRBR_STHR5_REG (0x50001044)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 63: UART_SRBR_STHR6_REG (0x50001048)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
52 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 63: UART_SRBR_STHR6_REG (0x50001048)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 64: UART_SRBR_STHR7_REG (0x5000104C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
53 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 64: UART_SRBR_STHR7_REG (0x5000104C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 65: UART_SRBR_STHR8_REG (0x50001050)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
54 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 65: UART_SRBR_STHR8_REG (0x50001050)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 66: UART_SRBR_STHR9_REG (0x50001054)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
55 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 66: UART_SRBR_STHR9_REG (0x50001054)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 67: UART_SRBR_STHR10_REG (0x50001058)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
56 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 67: UART_SRBR_STHR10_REG (0x50001058)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 68: UART_SRBR_STHR11_REG (0x5000105C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
57 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 68: UART_SRBR_STHR11_REG (0x5000105C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 69: UART_SRBR_STHR12_REG (0x50001060)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
58 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 69: UART_SRBR_STHR12_REG (0x50001060)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 70: UART_SRBR_STHR13_REG (0x50001064)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
59 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 70: UART_SRBR_STHR13_REG (0x50001064)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 71: UART_SRBR_STHR14_REG (0x50001068)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
60 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 71: UART_SRBR_STHR14_REG (0x50001068)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 72: UART_SRBR_STHR15_REG (0x5000106C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
61 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 72: UART_SRBR_STHR15_REG (0x5000106C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 73: UART_USR_REG (0x5000107C)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
4
R
UART_RFF
Receive FIFO Full.
This is used to indicate that the receive FIFO is completely
full.
0 = Receive FIFO not full
1 = Receive FIFO Full
This bit is cleared when the RX FIFO is no longer full.
0x0
3
R
UART_RFNE
Receive FIFO Not Empty.
This is used to indicate that the receive FIFO contains one or
more entries.
0 = Receive FIFO is empty
1 = Receive FIFO is not empty
This bit is cleared when the RX FIFO is empty.
0x0
2
R
UART_TFE
Transmit FIFO Empty.
This is used to indicate that the transmit FIFO is completely
empty.
0 = Transmit FIFO is not empty
1 = Transmit FIFO is empty
This bit is cleared when the TX FIFO is no longer empty.
0x1
Datasheet
CFR0011-120-01
Revision 3.4
62 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 73: UART_USR_REG (0x5000107C)
Bit
Mode
Symbol
Description
Reset
1
R
UART_TFNF
Transmit FIFO Not Full.
This is used to indicate that the transmit FIFO in not full.
0 = Transmit FIFO is full
1 = Transmit FIFO is not full
This bit is cleared when the TX FIFO is full.
0x1
0
-
-
Reserved
0x0
Table 74: UART_TFL_REG (0x50001080)
Bit
Mode
Symbol
Description
Reset
15:0
R
UART_TRANSMIT_F
IFO_LEVEL
Transmit FIFO Level.
This is indicates the number of data entries in the transmit
FIFO.
0x0
Table 75: UART_RFL_REG (0x50001084)
Bit
Mode
Symbol
Description
Reset
15:0
R
UART_RECEIVE_FI
FO_LEVEL
Receive FIFO Level.
This is indicates the number of data entries in the receive
FIFO.
0x0
Table 76: UART_SRR_REG (0x50001088)
Bit
Mode
Symbol
Description
Reset
15:3
-
-
Reserved
0x0
2
W
UART_XFR
XMIT FIFO Reset.
This is a shadow register for the XMIT FIFO Reset bit
(FCR[2]). This can be used to remove the burden on software having to store previously written FCR values (which
are pretty static) just to reset the transmit FIFO. This resets
the control portion of the transmit FIFO and treats the FIFO
as empty. Note that this bit is 'self-clearing'. It is not necessary to clear this bit.
0x0
1
W
UART_RFR
RCVR FIFO Reset.
This is a shadow register for the RCVR FIFO Reset bit
(FCR[1]). This can be used to remove the burden on software having to store previously written FCR values (which
are pretty static) just to reset the receive FIFO This resets
the control portion of the receive FIFO and treats the FIFO
as empty.
Note that this bit is 'self-clearing'. It is not necessary to clear
this bit.
0x0
0
W
UART_UR
UART Reset. This asynchronously resets the UART Ctrl and
synchronously removes the reset assertion. For a two clock
implementation both pclk and sclk domains are reset.
0x0
Table 77: UART_SRTS_REG (0x5000108C)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
63 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 77: UART_SRTS_REG (0x5000108C)
Bit
Mode
Symbol
Description
Reset
0
R/W
UART_SHADOW_R
EQUEST_TO_SEND
Shadow Request to Send.
This is a shadow register for the RTS bit (MCR[1]), this can
be used to remove the burden of having to perform a readmodify-write on the MCR. This is used to directly control the
Request to Send (rts_n) output. The Request To Send
(rts_n) output is used to inform the modem or data set that
the UART Ctrl is ready to exchange data.
When Auto Flow Control is disabled (MCR[5] = 0), the rts_n
signal is set low by programming MCR[1] (RTS) to a high.
When Auto Flow Control is enabled (MCR[5] = 1) and FIFOs
are enabled (FCR[0] = 1), the rts_n output is controlled in the
same way, but is also gated with the receiver FIFO threshold
trigger (rts_n is inactive high when above the threshold).
Note that in Loopback mode (MCR[4] = 1), the rts_n output is
held inactive-high while the value of this location is internally
looped back to an input.
0x0
Table 78: UART_SBCR_REG (0x50001090)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
UART_SHADOW_B
REAK_CONTROL
Shadow Break Control Bit.
This is a shadow register for the Break bit (LCR[6]), this can
be used to remove the burden of having to performing a read
modify write on the LCR. This is used to cause a break condition to be transmitted to the receiving device.
If set to one the serial output is forced to the spacing (logic 0)
state. When not in Loopback Mode, as determined by
MCR[4], the sout line is forced low until the Break bit is
cleared.
If SIR_MODE active (MCR[6] = 1) the sir_out_n line is continuously pulsed. When in Loopback Mode, the break condition is internally looped back to the receiver.
0x0
Table 79: UART_SDMAM_REG (0x50001094)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
UART_SHADOW_D
MA_MODE
Shadow DMA Mode.
This is a shadow register for the DMA mode bit (FCR[3]).
This can be used to remove the burden of having to store the
previously written value to the FCR in memory and having to
mask this value so that only the DMA Mode bit gets updated.
This determines the DMA signalling mode used for the
dma_tx_req_n and dma_rx_req_n output signals.
0 = mode 0
1 = mode 1
0x0
Table 80: UART_SFE_REG (0x50001098)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
64 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 80: UART_SFE_REG (0x50001098)
Bit
Mode
Symbol
Description
Reset
0
R/W
UART_SHADOW_FI
FO_ENABLE
Shadow FIFO Enable.
This is a shadow register for the FIFO enable bit (FCR[0]).
This can be used to remove the burden of having to store the
previously written value to the FCR in memory and having to
mask this value so that only the FIFO enable bit gets
updated.This enables/disables the transmit (XMIT) and
receive (RCVR) FIFOs. If this bit is set to zero (disabled)
after being enabled then both the XMIT and RCVR controller
portion of FIFOs are reset.
0x0
Table 81: UART_SRT_REG (0x5000109C)
Bit
Mode
Symbol
Description
Reset
15:2
-
-
Reserved
0x0
1:0
R/W
UART_SHADOW_R
CVR_TRIGGER
Shadow RCVR Trigger.
This is a shadow register for the RCVR trigger bits
(FCR[7:6]). This can be used to remove the burden of having
to store the previously written value to the FCR in memory
and having to mask this value so that only the RCVR trigger
bit gets updated.
This is used to select the trigger level in the receiver FIFO at
which the Received Data Available Interrupt is generated. It
also determines when the dma_rx_req_n signal is asserted
when DMA Mode (FCR[3]) = 1. The following trigger levels
are supported:
00 = 1 character in the FIFO
01 = FIFO ¼ full
10 = FIFO ½ full
11 = FIFO 2 less than full
0x0
Table 82: UART_STET_REG (0x500010A0)
Bit
Mode
Symbol
Description
Reset
15:2
-
-
Reserved
0x0
1:0
R/W
UART_SHADOW_TX
_EMPTY_TRIGGER
Shadow TX Empty Trigger.
This is a shadow register for the TX empty trigger bits
(FCR[5:4]). This can be used to remove the burden of having
to store the previously written value to the FCR in memory
and having to mask this value so that only the TX empty trigger bit gets updated.
This is used to select the empty threshold level at which the
THRE Interrupts are generated when the mode is active.
The following trigger levels are supported:
00 = FIFO empty
01 = 2 characters in the FIFO
10 = FIFO ¼ full
11 = FIFO ½ full
0x0
Table 83: UART_HTX_REG (0x500010A4)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
65 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 83: UART_HTX_REG (0x500010A4)
Bit
Mode
Symbol
Description
Reset
0
R/W
UART_HALT_TX
This register is use to halt transmissions for testing, so that
the transmit FIFO can be filled by the master when FIFOs
are implemented and enabled.
0 = Halt TX disabled
1 = Halt TX enabled
Note, if FIFOs are implemented and not enabled, the setting
of the halt TX register has no effect on operation.
0x0
Table 84: UART_CPR_REG (0x500010F4)
Bit
Mode
Symbol
Description
Reset
15:0
R
CPR
Component Parameter Register
0x0
Table 85: UART_UCV_REG (0x500010F8)
Bit
Mode
Symbol
Description
Reset
15:0
R
UCV
Component Version
0x33303
82A
Table 86: UART_CTR_REG (0x500010FC)
Bit
Mode
Symbol
Description
Reset
15:0
R
CTR
Component Type Register
0x44570
110
Table 87: UART2_RBR_THR_DLL_REG (0x50001100)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
66 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 87: UART2_RBR_THR_DLL_REG (0x50001100)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
RBR_THR_DLL
Receive Buffer Register: This register contains the data byte
received on the serial input port (sin) in UART mode or the
serial infrared input (sir_in) in infrared mode. The data in this
register is valid only if the Data Ready (DR) bit in the Line
status Register (LSR) is set. If FIFOs are disabled (FCR[0]
set to zero), the data in the RBR must be read before the
next data arrives, otherwise it will be overwritten, resulting in
an overrun error. If FIFOs are enabled (FCR[0] set to one),
this register accesses the head of the receive FIFO. If the
receive FIFO is full and this register is not read before the
next data character arrives, then the data already in the
FIFO will be preserved but any incoming data will be lost. An
overrun error will also occur. Transmit Holding Register: This
register contains data to be transmitted on the serial output
port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost. Divisor Latch (Low): This register makes up the lower 8bits of a 16-bit, read/write, Divisor Latch register that contains the baud rate divisor for the UART. This register may
only be accessed when the DLAB bit (LCR[7]) is set. The
output baud rate is equal to the serial clock (sclk) frequency
divided by sixteen times the value of the baud rate divisor, as
follows: baud rate = (serial clock freq) / (16 * divisor) Note
that with the Divisor Latch Registers (DLL and DLH) set to
zero, the baud clock is disabled and no serial communications will occur. Also, once the DLL is set, at least 8 clock
cycles of the slowest DW_apb_uart clock should be allowed
to pass before transmitting or receiving data.
0x0
Table 88: UART2_IER_DLH_REG (0x50001104)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R/W
PTIME_DLH7
Interrupt Enable Register: PTIME, Programmable THRE
Interrupt Mode Enable. This is used to enable/disable the
generation of THRE Interrupt. 0 = disabled 1 = enabled Divisor Latch (High): Bit[7] of the 8 bit DLH register.
0x0
6:4
-
-
Reserved
0x0
3
R/W
EDSSI_DLH3
Interrupt Enable Register: EDSSI, Enable Modem Status
Interrupt. This is used to enable/disable the generation of
Modem Status Interrupt. This is the fourth highest priority
interrupt. 0 = disabled 1 = enabled Divisor Latch (High):
Bit[3] of the 8 bit DLH register
0x0
Datasheet
CFR0011-120-01
Revision 3.4
67 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 88: UART2_IER_DLH_REG (0x50001104)
Bit
Mode
Symbol
Description
Reset
2
R/W
ELSI_DHL2
Interrupt Enable Register: ELSI, Enable Receiver Line Status Interrupt. This is used to enable/disable the generation of
Receiver Line Status Interrupt. This is the highest priority
interrupt. 0 = disabled 1 = enabled Divisor Latch (High):
Bit[2] of the 8 bit DLH register.
0x0
1
R/W
ETBEI_DLH1
Interrupt Enable Register: ETBEI, Enable Transmit Holding
Register Empty Interrupt. This is used to enable/disable the
generation of Transmitter Holding Register Empty Interrupt.
This is the third highest priority interrupt. 0 = disabled 1 =
enabled Divisor Latch (High): Bit[1] of the 8 bit DLH register.
0x0
0
R/W
ERBFI_DLH0
Interrupt Enable Register: ERBFI, Enable Received Data
Available Interrupt. This is used to enable/disable the generation of Received Data Available Interrupt and the Character
Timeout Interrupt (if in FIFO mode and FIFO's enabled).
These are the second highest priority interrupts. 0 = disabled
1 = enabled Divisor Latch (High): Bit[0] of the 8 bit DLH register.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
68 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 89: UART2_IIR_FCR_REG (0x50001108)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IIR_FCR
Interrupt Identification Register, reading this register; FIFO
Control Register, writing to this register. Interrupt Identification Register: Bits[7:6], FIFO's Enabled (or FIFOSE): This is
used to indicate whether the FIFO's are enabled or disabled.
00 = disabled. 11 = enabled. Bits[3:0], Interrupt ID (or IID):
This indicates the highest priority pending interrupt which
can be one of the following types: 0000 = modem status.
0001 = no interrupt pending. 0010 = THR empty. 0100 =
received data available. 0110 = receiver line status. 0111 =
busy detect. 1100 = character timeout. Bits[7:6], RCVR Trigger (or RT):. This is used to select the trigger level in the
receiver FIFO at which the Received Data Available Interrupt
will be generated. In auto flow control mode it is used to
determine when the rts_n signal will be de-asserted. It also
determines when the dma_rx_req_n signal will be asserted
when in certain modes of operation. The following trigger
levels are supported: 00 = 1 character in the FIFO 01 = FIFO
1/4 full 10 = FIFO 1/2 full 11 = FIFO 2 less than full Bits[5:4],
TX Empty Trigger (or TET): This is used to select the empty
threshold level at which the THRE Interrupts will be generated when the mode is active. It also determines when the
dma_tx_req_n signal will be asserted when in certain modes
of operation. The following trigger levels are supported: 00 =
FIFO empty 01 = 2 characters in the FIFO 10 = FIFO 1/4 full
11 = FIFO 1/2 full Bit[3], DMA Mode (or DMAM): This determines the DMA signalling mode used for the dma_tx_req_n
and dma_rx_req_n output signals. 0 = mode 0 1 = mode 1
Bit[2], XMIT FIFO Reset (or XFIFOR): This resets the control
portion of the transmit FIFO and treats the FIFO as empty.
Note that this bit is 'self-clearing' and it is not necessary to
clear this bit. Bit[1], RCVR FIFO Reset (or RFIFOR): This
resets the control portion of the receive FIFO and treats the
FIFO as empty. Note that this bit is 'self-clearing' and it is not
necessary to clear this bit. Bit[0], FIFO Enable (or FIFOE):
This enables/disables the transmit (XMIT) and receive
(RCVR) FIFO's. Whenever the value of this bit is changed
both the XMIT and RCVR controller portion of FIFO's will be
reset.
0x0
Table 90: UART2_LCR_REG (0x5000110C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7
R/W
UART_DLAB
Divisor Latch Access Bit.
This bit is used to enable reading and writing of the Divisor
Latch register (DLL and DLH) to set the baud rate of the
UART.
This bit must be cleared after initial baud rate setup in order
to access other registers.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
69 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 90: UART2_LCR_REG (0x5000110C)
Bit
Mode
Symbol
Description
Reset
6
R/W
UART_BC
Break Control Bit.
This is used to cause a break condition to be transmitted to
the receiving device. If set to one the serial output is forced
to the spacing (logic 0) state. When not in Loopback Mode,
as determined by MCR[4], the sout line is forced low until the
Break bit is cleared. If active (MCR[6] set to one) the
sir_out_n line is continuously pulsed. When in Loopback
Mode, the break condition is internally looped back to the
receiver and the sir_out_n line is forced low.
0x0
5
-
-
Reserved
0x0
4
R/W
UART_EPS
Even Parity Select.
This is used to select between even and odd parity, when
parity is enabled (PEN set to one). If set to one, an even
number of logic 1s is transmitted or checked. If set to zero,
an odd number of logic 1s is transmitted or checked.
0x0
3
R/W
UART_PEN
Parity Enable.
This bit is used to enable and disable parity generation and
detection in transmitted and received serial character
respectively.
0 = parity disabled
1 = parity enabled
0x0
2
R/W
UART_STOP
Number of stop bits.
This is used to select the number of stop bits per character
that the peripheral transmits and receives. If set to zero, one
stop bit is transmitted in the serial data.
If set to one and the data bits are set to 5 (LCR[1:0] set to
zero) one and a half stop bits is transmitted. Otherwise, two
stop bits are transmitted. Note that regardless of the number
of stop bits selected, the receiver checks only the first stop
bit.
0 = 1 stop bit
1 = 1.5 stop bits when DLS (LCR[1:0]) is zero, else 2 stop bit
0x0
1:0
R/W
UART_DLS
Data Length Select.
This is used to select the number of data bits per character
that the peripheral transmits and receives. The number of bit
that may be selected areas follows:
00 = 5 bits
01 = 6 bits
10 = 7 bits
11 = 8 bits
0x0
Table 91: UART2_MCR_REG (0x50001110)
Bit
Mode
Symbol
Description
Reset
15:7
-
-
Reserved
0x0
6
R/W
UART_SIRE
SIR Mode Enable.
This is used to enable/disable the IrDA SIR Mode features
as described in "IrDA 1.0 SIR Protocol" on page 53.
0 = IrDA SIR Mode disabled
1 = IrDA SIR Mode enabled
0x0
5
R/W
UART_AFCE
Auto Flow Control Enable.
When FIFOs are enabled and the Auto Flow Control Enable
(AFCE) bit is set, hardware Auto Flow Control is enabled via
CTS and RTS.
0 = Auto Flow Control Mode disabled
1 = Auto Flow Control Mode enabled
0x0
Datasheet
CFR0011-120-01
Revision 3.4
70 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 91: UART2_MCR_REG (0x50001110)
Bit
Mode
Symbol
Description
Reset
4
R/W
UART_LB
LoopBack Bit.
This is used to put the UART into a diagnostic mode for test
purposes.
If operating in UART mode (SIR_MODE not active, MCR[6]
set to zero), data on the sout line is held high, while serial
data output is looped back to the sin line, internally. In this
mode all the interrupts are fully functional. Also, in loopback
mode, the modem control inputs (dsr_n, cts_n, ri_n, dcd_n)
are disconnected and the modem control outputs (dtr_n,
rts_n, out1_n, out2_n) are looped back to the inputs, internally.
If operating in infrared mode (SIR_MODE active, MCR[6] set
to one), data on the sir_out_n line is held low, while serial
data output is inverted and looped back to the sir_in line.
0x0
3
R/W
UART_OUT2
OUT2.
This is used to directly control the user-designated Output2
(out2_n) output. The value written to this location is inverted
and driven out on out2_n, that is:
0 = out2_n de-asserted (logic 1)
1 = out2_n asserted (logic 0)
Note that in Loopback mode (MCR[4] set to one), the out2_n
output is held inactive high while the value of this location is
internally looped back to an input.
0x0
2
R/W
UART_OUT1
OUT1.
This is used to directly control the user-designated Output1
(out1_n) output. The value written to this location is inverted
and driven out on out1_n, that is:
0 = out1_n de-asserted (logic 1)
1 = out1_n asserted (logic 0)
Note that in Loopback mode (MCR[4] set to one), the out1_n
output is held inactive high while the value of this location is
internally looped back to an input.
0x0
1
R/W
UART_RTS
Request to Send.
This is used to directly control the Request to Send (rts_n)
output. The Request To Send (rts_n) output is used to inform
the modem or data set that the UART is ready to exchange
data.
When Auto Flow Control is disabled (MCR[5] set to zero),
the rts_n signal is set low by programming MCR[1] (RTS) to
a high. When Auto Flow Control is enabled (MCR[5] set to
one) and FIFOs are enabled (FCR[0] set to one), the rts_n
output is controlled in the same way, but is also gated with
the receiver FIFO threshold trigger (rts_n is inactive high
when above the threshold). The rts_n signal is de-asserted
when MCR[1] is set low.
Note that in Loopback mode (MCR[4] set to one), the rts_n
output is held inactive (high) while the value of this location is
internally looped back to an input.
0x0
0
-
-
Reserved
0x0
Table 92: UART2_LSR_REG (0x50001114)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
71 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 92: UART2_LSR_REG (0x50001114)
Bit
Mode
Symbol
Description
Reset
7
R
UART_RFE
Receiver FIFO Error bit.
This bit is only relevant when FIFOs are enabled (FCR[0] set
to one). This is used to indicate if there is at least one parity
error, framing error, or break indication in the FIFO.
0 = no error in RX FIFO
1 = error in RX FIFO
This bit is cleared when the LSR is read and the character
with the error is at the top of the receiver FIFO and there are
no subsequent errors in the FIFO.
0x0
6
R
UART_TEMT
Transmitter Empty bit.
If FIFOs enabled (FCR[0] set to one), this bit is set whenever
the Transmitter Shift Register and the FIFO are both empty.
If FIFOs are disabled, this bit is set whenever the Transmitter
Holding Register and the Transmitter Shift Register are both
empty.
0x1
5
R
UART_THRE
Transmit Holding Register Empty bit.
If THRE mode is disabled (IER[7] set to zero) and regardless
of FIFO's being implemented/enabled or not, this bit indicates that the THR or TX FIFO is empty.
This bit is set whenever data is transferred from the THR or
TX FIFO to the transmitter shift register and no new data has
been written to the THR or TX FIFO. This also causes a
THRE Interrupt to occur, if the THRE Interrupt is enabled. If
both modes are active (IER[7] set to one and FCR[0] set to
one respectively), the functionality is switched to indicate the
transmitter FIFO is full, and no longer controls THRE interrupts, which are then controlled by the FCR[5:4] threshold
setting.
0x1
4
R
UART_B1
Break Interrupt bit.
This is used to indicate the detection of a break sequence on
the serial input data.
If in UART mode (SIR_MODE == Disabled), it is set whenever the serial input, sin, is held in a logic '0' state for longer
than the sum of start time + data bits + parity + stop bits.
If in infrared mode (SIR_MODE == Enabled), it is set whenever the serial input, sir_in, is continuously pulsed to logic '0'
for longer than the sum of start time + data bits + parity +
stop bits. A break condition on serial input causes one and
only one character, consisting of all zeros, to be received by
the UART.
In the FIFO mode, the character associated with the break
condition is carried through the FIFO and is revealed when
the character is at the top of the FIFO.
Reading the LSR clears the BI bit. In the non-FIFO mode,
the BI indication occurs immediately and persists until the
LSR is read.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
72 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 92: UART2_LSR_REG (0x50001114)
Bit
Mode
Symbol
Description
Reset
3
R
UART_FE
Framing Error bit.
This is used to indicate the occurrence of a framing error in
the receiver. A framing error occurs when the receiver does
not detect a valid STOP bit in the received data.
In the FIFO mode, since the framing error is associated with
a character received, it is revealed when the character with
the framing error is at the top of the FIFO.
When a framing error occurs, the UART tries to resynchronize. It does this by assuming that the error was due to the
start bit of the next character and then continues receiving
the other bit i.e. data, and/or parity and stop. It should be
noted that the Framing Error (FE) bit (LSR[3]) is set if a
break interrupt has occurred, as indicated by Break Interrupt
(BI) bit (LSR[4]).
0 = no framing error
1 = framing error
Reading the LSR clears the FE bit.
0x0
2
R
UART_PE
Parity Error bit.
This is used to indicate the occurrence of a parity error in the
receiver if the Parity Enable (PEN) bit (LCR[3]) is set.
In the FIFO mode, since the parity error is associated with a
character received, it is revealed when the character with the
parity error arrives at the top of the FIFO.
It should be noted that the Parity Error (PE) bit (LSR[2]) is
set if a break interrupt has occurred, as indicated by Break
Interrupt (BI) bit (LSR[4]).
0 = no parity error
1 = parity error
Reading the LSR clears the PE bit.
0x0
1
R
UART_OE
Overrun error bit.
This is used to indicate the occurrence of an overrun error.
This occurs if a new data character was received before the
previous data was read.
In the non-FIFO mode, the OE bit is set when a new character arrives in the receiver before the previous character was
read from the RBR. When this happens, the data in the RBR
is overwritten. In the FIFO mode, an overrun error occurs
when the FIFO is full and a new character arrives at the
receiver. The data in the FIFO is retained and the data in the
receive shift register is lost.
0 = no overrun error
1 = overrun error
Reading the LSR clears the OE bit.
0x0
0
R
UART_DR
Data Ready bit.
This is used to indicate that the receiver contains at least
one character in the RBR or the receiver FIFO.
0 = no data ready
1 = data ready
This bit is cleared when the RBR is read in non-FIFO mode,
or when the receiver FIFO is empty, in FIFO mode.
0x0
Table 93: UART2_MSR_REG (0x50001118)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
73 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 93: UART2_MSR_REG (0x50001118)
Bit
Mode
Symbol
Description
Reset
7
R
UART_DCD
Data Carrier Detect.
This is used to indicate the current state of the modem control line dcd_n. This bit is the complement of dcd_n. When
the Data Carrier Detect input (dcd_n) is asserted it is an indication that the carrier has been detected by the modem or
data set.
0 = dcd_n input is de-asserted (logic 1)
1 = dcd_n input is asserted (logic 0)
In Loopback Mode (MCR[4] set to one), DCD is the same as
MCR[3] (Out2).
0x0
6
R
UART_R1
Ring Indicator.
This is used to indicate the current state of the modem control line ri_n. This bit is the complement of ri_n. When the
Ring Indicator input (ri_n) is asserted it is an indication that a
telephone ringing signal has been received by the modem or
data set.
0 = ri_n input is de-asserted (logic 1)
1 = ri_n input is asserted (logic 0)
In Loopback Mode (MCR[4] set to one), RI is the same as
MCR[2] (Out1).
0x0
5
-
-
Reserved
0x0
4
R
UART_CTS
Clear to Send.
This is used to indicate the current state of the modem control line cts_n. This bit is the complement of cts_n. When the
Clear to Send input (cts_n) is asserted it is an indication that
the modem or data set is ready to exchange data with the
UART Ctrl.
0 = cts_n input is de-asserted (logic 1)
1 = cts_n input is asserted (logic 0)
In Loopback Mode (MCR[4] = 1), CTS is the same as
MCR[1] (RTS).
0x0
3
R
UART_DDCD
Delta Data Carrier Detect.
This is used to indicate that the modem control line dcd_n
has changed since the last time the MSR was read.
0 = no change on dcd_n since last read of MSR
1 = change on dcd_n since last read of MSR
Reading the MSR clears the DDCD bit. In Loopback Mode
(MCR[4] = 1), DDCD reflects changes on MCR[3] (Out2).
Note, if the DDCD bit is not set and the dcd_n signal is
asserted (low) and a reset occurs (software or otherwise),
then the DDCD bit is set when the reset is removed if the
dcd_n signal remains asserted.
0x0
2
R
UART_TERI
Trailing Edge of Ring Indicator.
This is used to indicate that a change on the input ri_n (from
an active-low to an inactive-high state) has occurred since
the last time the MSR was read.
0 = no change on ri_n since last read of MSR
1 = change on ri_n since last read of MSR
Reading the MSR clears the TERI bit. In Loopback Mode
(MCR[4] = 1), TERI reflects when MCR[2] (Out1) has
changed state from a high to a low.
0x0
1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
74 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 93: UART2_MSR_REG (0x50001118)
Bit
Mode
Symbol
Description
Reset
0
R
UART_DCTS
Delta Clear to Send.
This is used to indicate that the modem control line cts_n
has changed since the last time the MSR was read.
0 = no change on cts_n since last read of MSR
1 = change on cts_n since last read of MSR
Reading the MSR clears the DCTS bit. In Loopback Mode
(MCR[4] = 1), DCTS reflects changes on MCR[1] (RTS).
Note, if the DCTS bit is not set and the cts_n signal is
asserted (low) and a reset occurs (software or otherwise),
then the DCTS bit is set when the reset is removed if the
cts_n signal remains asserted.
0x0
Table 94: UART2_SCR_REG (0x5000111C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
UART_SCRATCH_P
AD
This register is for programmers to use as a temporary storage space. It has no defined purpose in the UART Ctrl.
0x0
Table 95: UART2_LPDLL_REG (0x50001120)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
UART_LPDLL
This register makes up the lower 8-bits of a 16-bit, read/
write, Low Power Divisor Latch register that contains the
baud rate divisor for the UART, which must give a baud rate
of 115.2K. This is required for SIR Low Power (minimum
pulse width) detection at the receiver. This register may be
accessed only when the DLAB bit (LCR[7]) is set.
The output low-power baud rate is equal to the serial clock
(sclk) frequency divided by sixteen times the value of the
baud rate divisor, as follows:
Low power baud rate = (serial clock frequency)/(16* divisor)
Therefore, a divisor must be selected to give a baud rate of
115.2K.
NOTE: When the Low Power Divisor Latch registers (LPDLL
and LPDLH) are set to 0, the low-power baud clock is disabled and no low-power pulse detection (or any pulse detection) occurs at the receiver. Also, once the LPDLL is set, at
least eight clock cycles of the slowest UART Ctrl clock
should be allowed to pass before transmitting or receiving
data.
0x0
Table 96: UART2_LPDLH_REG (0x50001124)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
75 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 96: UART2_LPDLH_REG (0x50001124)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
UART_LPDLH
This register makes up the upper 8-bits of a 16-bit, read/
write, Low Power Divisor Latch register that contains the
baud rate divisor for the UART, which must give a baud rate
of 115.2K. This is required for SIR Low Power (minimum
pulse width) detection at the receiver. This register may be
accessed only when the DLAB bit (LCR[7]) is set.
The output low-power baud rate is equal to the serial clock
(sclk) frequency divided by sixteen times the value of the
baud rate divisor, as follows:
Low power baud rate = (serial clock frequency)/(16* divisor)
Therefore, a divisor must be selected to give a baud rate of
115.2K.
NOTE: When the Low Power Divisor Latch registers (LPDLL
and LPDLH) are set to 0, the low-power baud clock is disabled and no low-power pulse detection (or any pulse detection) occurs at the receiver. Also, once the LPDLH is set, at
least eight clock cycles of the slowest UART Ctrl clock
should be allowed to pass before transmitting or receiving
data.
0x0
Table 97: UART2_SRBR_STHR0_REG (0x50001130)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
76 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 98: UART2_SRBR_STHR1_REG (0x50001134)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 99: UART2_SRBR_STHR2_REG (0x50001138)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
77 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 99: UART2_SRBR_STHR2_REG (0x50001138)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 100: UART2_SRBR_STHR3_REG (0x5000113C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
78 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 100: UART2_SRBR_STHR3_REG (0x5000113C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 101: UART2_SRBR_STHR4_REG (0x50001140)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
79 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 101: UART2_SRBR_STHR4_REG (0x50001140)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 102: UART2_SRBR_STHR5_REG (0x50001144)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
80 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 102: UART2_SRBR_STHR5_REG (0x50001144)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 103: UART2_SRBR_STHR6_REG (0x50001148)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
81 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 103: UART2_SRBR_STHR6_REG (0x50001148)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 104: UART2_SRBR_STHR7_REG (0x5000114C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
82 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 104: UART2_SRBR_STHR7_REG (0x5000114C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 105: UART2_SRBR_STHR8_REG (0x50001150)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
83 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 105: UART2_SRBR_STHR8_REG (0x50001150)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 106: UART2_SRBR_STHR9_REG (0x50001154)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
84 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 106: UART2_SRBR_STHR9_REG (0x50001154)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 107: UART2_SRBR_STHR10_REG (0x50001158)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
85 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 107: UART2_SRBR_STHR10_REG (0x50001158)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 108: UART2_SRBR_STHR11_REG (0x5000115C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
86 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 108: UART2_SRBR_STHR11_REG (0x5000115C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 109: UART2_SRBR_STHR12_REG (0x50001160)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
87 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 109: UART2_SRBR_STHR12_REG (0x50001160)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 110: UART2_SRBR_STHR13_REG (0x50001164)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
88 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 110: UART2_SRBR_STHR13_REG (0x50001164)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 111: UART2_SRBR_STHR14_REG (0x50001168)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
89 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 111: UART2_SRBR_STHR14_REG (0x50001168)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 112: UART2_SRBR_STHR15_REG (0x5000116C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
90 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 112: UART2_SRBR_STHR15_REG (0x5000116C)
Bit
Mode
Symbol
Description
Reset
7:0
R/W
SRBR_STHRX
Shadow Receive Buffer Register x: This is a shadow register
for the RBR and has been allocated sixteen 32-bit locations
so as to accommodate burst accesses from the master. This
register contains the data byte received on the serial input
port (sin) in UART mode or the serial infrared input (sir_in) in
infrared mode. The data in this register is valid only if the
Data Ready (DR) bit in the Line status Register (LSR) is set.
If FIFOs are disabled (FCR[0] set to zero), the data in the
RBR must be read before the next data arrives, otherwise it
will be overwritten, resulting in an overrun error. If FIFOs are
enabled (FCR[0] set to one), this register accesses the head
of the receive FIFO. If the receive FIFO is full and this register is not read before the next data character arrives, then
the data already in the FIFO will be preserved but any
incoming data will be lost. An overrun error will also occur.
Shadow Transmit Holding Register 0: This is a shadow register for the THR and has been allocated sixteen 32-bit locations so as to accommodate burst accesses from the master.
This register contains data to be transmitted on the serial
output port (sout) in UART mode or the serial infrared output
(sir_out_n) in infrared mode. Data should only be written to
the THR when the THR Empty (THRE) bit (LSR[5]) is set. If
FIFO's are disabled (FCR[0] set to zero) and THRE is set,
writing a single character to the THR clears the THRE. Any
additional writes to the THR before the THRE is set again
causes the THR data to be overwritten. If FIFO's are enabled
(FCR[0] set to one) and THRE is set, x number of characters
of data may be written to the THR before the FIFO is full.
The number x (default=16) is determined by the value of
FIFO Depth that you set during configuration. Any attempt to
write data when the FIFO is full results in the write data being
lost.
0x0
Table 113: UART2_USR_REG (0x5000117C)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
4
R
UART_RFF
Receive FIFO Full.
This is used to indicate that the receive FIFO is completely
full.
0 = Receive FIFO not full
1 = Receive FIFO Full
This bit is cleared when the RX FIFO is no longer full.
0x0
3
R
UART_RFNE
Receive FIFO Not Empty.
This is used to indicate that the receive FIFO contains one or
more entries.
0 = Receive FIFO is empty
1 = Receive FIFO is not empty
This bit is cleared when the RX FIFO is empty.
0x0
2
R
UART_TFE
Transmit FIFO Empty.
This is used to indicate that the transmit FIFO is completely
empty.
0 = Transmit FIFO is not empty
1 = Transmit FIFO is empty
This bit is cleared when the TX FIFO is no longer empty.
0x1
Datasheet
CFR0011-120-01
Revision 3.4
91 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 113: UART2_USR_REG (0x5000117C)
Bit
Mode
Symbol
Description
Reset
1
R
UART_TFNF
Transmit FIFO Not Full.
This is used to indicate that the transmit FIFO in not full.
0 = Transmit FIFO is full
1 = Transmit FIFO is not full
This bit is cleared when the TX FIFO is full.
0x1
0
-
-
Reserved
0x0
Table 114: UART2_TFL_REG (0x50001180)
Bit
Mode
Symbol
Description
Reset
15:0
R
UART_TRANSMIT_F
IFO_LEVEL
Transmit FIFO Level.
This is indicates the number of data entries in the transmit
FIFO.
0x0
Table 115: UART2_RFL_REG (0x50001184)
Bit
Mode
Symbol
Description
Reset
15:0
R
UART_RECEIVE_FI
FO_LEVEL
Receive FIFO Level.
This is indicates the number of data entries in the receive
FIFO.
0x0
Table 116: UART2_SRR_REG (0x50001188)
Bit
Mode
Symbol
Description
Reset
15:3
-
-
Reserved
0x0
2
W
UART_XFR
XMIT FIFO Reset.
This is a shadow register for the XMIT FIFO Reset bit
(FCR[2]). This can be used to remove the burden on software having to store previously written FCR values (which
are pretty static) just to reset the transmit FIFO. This resets
the control portion of the transmit FIFO and treats the FIFO
as empty. Note that this bit is 'self-clearing'. It is not necessary to clear this bit.
0x0
1
W
UART_RFR
RCVR FIFO Reset.
This is a shadow register for the RCVR FIFO Reset bit
(FCR[1]). This can be used to remove the burden on software having to store previously written FCR values (which
are pretty static) just to reset the receive FIFO This resets
the control portion of the receive FIFO and treats the FIFO
as empty.
Note that this bit is 'self-clearing'. It is not necessary to clear
this bit.
0x0
0
W
UART_UR
UART Reset. This asynchronously resets the UART Ctrl and
synchronously removes the reset assertion. For a two clock
implementation both pclk and sclk domains are reset.
0x0
Table 117: UART2_SRTS_REG (0x5000118C)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
92 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 117: UART2_SRTS_REG (0x5000118C)
Bit
Mode
Symbol
Description
Reset
0
R/W
UART_SHADOW_R
EQUEST_TO_SEND
Shadow Request to Send.
This is a shadow register for the RTS bit (MCR[1]), this can
be used to remove the burden of having to perform a readmodify-write on the MCR. This is used to directly control the
Request to Send (rts_n) output. The Request To Send
(rts_n) output is used to inform the modem or data set that
the UART Ctrl is ready to exchange data.
When Auto Flow Control is disabled (MCR[5] = 0), the rts_n
signal is set low by programming MCR[1] (RTS) to a high.
When Auto Flow Control is enabled (MCR[5] = 1) and FIFOs
are enabled (FCR[0] = 1), the rts_n output is controlled in the
same way, but is also gated with the receiver FIFO threshold
trigger (rts_n is inactive high when above the threshold).
Note that in Loopback mode (MCR[4] = 1), the rts_n output is
held inactive-high while the value of this location is internally
looped back to an input.
0x0
Table 118: UART2_SBCR_REG (0x50001190)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
UART_SHADOW_B
REAK_CONTROL
Shadow Break Control Bit.
This is a shadow register for the Break bit (LCR[6]), this can
be used to remove the burden of having to performing a read
modify write on the LCR. This is used to cause a break condition to be transmitted to the receiving device.
If set to one the serial output is forced to the spacing (logic 0)
state. When not in Loopback Mode, as determined by
MCR[4], the sout line is forced low until the Break bit is
cleared.
If SIR_MODE active (MCR[6] = 1) the sir_out_n line is continuously pulsed. When in Loopback Mode, the break condition is internally looped back to the receiver.
0x0
Table 119: UART2_SDMAM_REG (0x50001194)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
UART_SHADOW_D
MA_MODE
Shadow DMA Mode.
This is a shadow register for the DMA mode bit (FCR[3]).
This can be used to remove the burden of having to store the
previously written value to the FCR in memory and having to
mask this value so that only the DMA Mode bit gets updated.
This determines the DMA signalling mode used for the
dma_tx_req_n and dma_rx_req_n output signals.
0 = mode 0
1 = mode 1
0x0
Table 120: UART2_SFE_REG (0x50001198)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
93 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 120: UART2_SFE_REG (0x50001198)
Bit
Mode
Symbol
Description
Reset
0
R/W
UART_SHADOW_FI
FO_ENABLE
Shadow FIFO Enable.
This is a shadow register for the FIFO enable bit (FCR[0]).
This can be used to remove the burden of having to store the
previously written value to the FCR in memory and having to
mask this value so that only the FIFO enable bit gets
updated.This enables/disables the transmit (XMIT) and
receive (RCVR) FIFOs. If this bit is set to zero (disabled)
after being enabled then both the XMIT and RCVR controller
portion of FIFOs are reset.
0x0
Table 121: UART2_SRT_REG (0x5000119C)
Bit
Mode
Symbol
Description
Reset
15:2
-
-
Reserved
0x0
1:0
R/W
UART_SHADOW_R
CVR_TRIGGER
Shadow RCVR Trigger.
This is a shadow register for the RCVR trigger bits
(FCR[7:6]). This can be used to remove the burden of having
to store the previously written value to the FCR in memory
and having to mask this value so that only the RCVR trigger
bit gets updated.
This is used to select the trigger level in the receiver FIFO at
which the Received Data Available Interrupt is generated. It
also determines when the dma_rx_req_n signal is asserted
when DMA Mode (FCR[3]) = 1. The following trigger levels
are supported:
00 = 1 character in the FIFO
01 = FIFO ¼ full
10 = FIFO ½ full
11 = FIFO 2 less than full
0x0
Table 122: UART2_STET_REG (0x500011A0)
Bit
Mode
Symbol
Description
Reset
15:2
-
-
Reserved
0x0
1:0
R/W
UART_SHADOW_TX
_EMPTY_TRIGGER
Shadow TX Empty Trigger.
This is a shadow register for the TX empty trigger bits
(FCR[5:4]). This can be used to remove the burden of having
to store the previously written value to the FCR in memory
and having to mask this value so that only the TX empty trigger bit gets updated.
This is used to select the empty threshold level at which the
THRE Interrupts are generated when the mode is active.
The following trigger levels are supported:
00 = FIFO empty
01 = 2 characters in the FIFO
10 = FIFO ¼ full
11 = FIFO ½ full
0x0
Table 123: UART2_HTX_REG (0x500011A4)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
94 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 123: UART2_HTX_REG (0x500011A4)
Bit
Mode
Symbol
Description
Reset
0
R/W
UART_HALT_TX
This register is use to halt transmissions for testing, so that
the transmit FIFO can be filled by the master when FIFOs
are implemented and enabled.
0 = Halt TX disabled
1 = Halt TX enabled
Note, if FIFOs are implemented and not enabled, the setting
of the halt TX register has no effect on operation.
0x0
Table 124: UART2_CPR_REG (0x500011F4)
Bit
Mode
Symbol
Description
Reset
15:0
R
CPR
Component Parameter Register
0x0
Table 125: UART2_UCV_REG (0x500011F8)
Bit
Mode
Symbol
Description
Reset
15:0
R
UCV
Component Version
0x33303
82A
Table 126: UART2_CTR_REG (0x500011FC)
Bit
Mode
Symbol
Description
Reset
15:0
R
CTR
Component Type Register
0x44570
110
Table 127: SPI_CTRL_REG (0x50001200)
Bit
Mode
Symbol
Description
Reset
15
R/W
SPI_EN_CTRL
0 = SPI_EN pin disabled in slave mode. Pin SPI_EN is don't
care.
1 = SPI_EN pin enabled in slave mode.
0x0
14
R/W
SPI_MINT
0 = Disable SPI_INT_BIT to the Interrupt Controller
1 = Enable SPI_INT_BIT to the Interrupt Controller
0x0
13
R
SPI_INT_BIT
0 = RX Register or FIFO is empty.
1 = SPI interrupt. Data has been transmitted and receivedMust be reset by SW by writing to SPI_CLEAR_INT_REG.
0x0
12
R
SPI_DI
Returns the actual value of pin SPI_DIN (delayed with two
internal SPI clock cycles)
0x0
11
R
SPI_TXH
0 = TX-FIFO is not full, data can be written.
1 = TX-FIFO is full, data can not be written.
0x0
10
R/W
SPI_FORCE_DO
0 = normal operation
1 = Force SPIDO output level to value of SPI_DO.
0x0
9
R/W
SPI_RST
0 = normal operation
1 = Reset SPI. Same function as SPI_ON except that internal clock remain active.
0x0
8:7
R/W
SPI_WORD
00 = 8 bits mode, only SPI_RX_TX_REG0 used
01 = 16 bit mode, only SPI_RX_TX_REG0 used
10 = 32 bits mode, SPI_RX_TX_REG0 &
SPI_RX_TX_REG1 used
11 = 9 bits mode. Only valid in master mode.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
95 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 127: SPI_CTRL_REG (0x50001200)
Bit
Mode
Symbol
Description
Reset
6
R/W
SPI_SMN
Master/slave mode
0 = Master,
1 = Slave(SPI1 only)
0x0
5
R/W
SPI_DO
Pin SPI_DO output level when SPI is idle or when
SPI_FORCE_DO=1
0x0
4:3
R/W
SPI_CLK
Select SPI_CLK clock frequency in master mode:00 =
(XTAL) / (CLK_PER_REG *8)
01 = (XTAL) / (CLK_PER_REG *4)
10 = (XTAL) / (CLK_PER_REG *2)
11 = (XTAL) / (CLK_PER_REG *14)
0x0
2
R/W
SPI_POL
Select SPI_CLK polarity.
0 = SPI_CLK is initially low.
1 = SPI_CLK is initially high.
0x0
1
R/W
SPI_PHA
Select SPI_CLK phase. See functional timing diagrams in
SPI chapter
0x0
0
R/W
SPI_ON
0 = SPI Module switched off (power saving). Everything is
reset except SPI_CTRL_REG0 and SPI_CTRL_REG1.
When this bit is cleared the SPI will remain active in master
mode until the shift register and holding register are both
empty.
1 = SPI Module switched on. Should only be set after all control bits have their desired values. So two writes are needed!
0x0
Table 128: SPI_RX_TX_REG0 (0x50001202)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
SPI_DATA0
Write: SPI_TX_REG0 output register 0 (TX-FIFO)
Read: SPI_RX_REG0 input register 0 (RX-FIFO)
In 8 or 9 bits mode bits 15 to 8 are not used, they contain old
data.
0x0
Table 129: SPI_RX_TX_REG1 (0x50001204)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
SPI_DATA1
Write: SPI_TX_REG1 output register 1 (MSB's of TX-FIFO)
Read: SPI_RX_REG1 input register 1 (MSB's of RX-FIFO)
In 8 or 9 or 16 bits mode bits this register is not used.
0x0
Table 130: SPI_CLEAR_INT_REG (0x50001206)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
SPI_CLEAR_INT
Writing any value to this register will clear the
SPI_CTRL_REG[SPI_INT_BIT]
Reading returns 0.
0x0
Table 131: SPI_CTRL_REG1 (0x50001208)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
4
R/W
SPI_9BIT_VAL
Determines the value of the first bit in 9 bits SPI mode.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
96 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 131: SPI_CTRL_REG1 (0x50001208)
Bit
Mode
Symbol
Description
Reset
3
R
SPI_BUSY
0 = The SPI is not busy with a transfer. This means that
either no TX-data is available or that the transfers have been
suspended due to a full RX-FIFO. The
SPIx_CTRL_REG0[SPI_INT_BIT] can be used to distinguish
between these situations.
1 = The SPI is busy with a transfer.
0x0
2
R/W
SPI_PRIORITY
0 = The SPI has low priority, the DMA request signals are
reset after the corresponding acknowledge.
1 = The SPI has high priority, DMA request signals remain
active until the FIFOS are filled/emptied, so the DMA holds
the AHB bus.
0x0
1:0
R/W
SPI_FIFO_MODE
0: TX-FIFO and RX-FIFO used (Bidirectional mode).
1: RX-FIFO used (Read Only Mode) TX-FIFO single depth,
no flow control
2: TX-FIFO used (Write Only Mode), RX-FIFO single depth,
no flow control
3: No FIFOs used (backwards compatible mode)
0x3
Table 132: I2C_CON_REG (0x50001300)
Bit
Mode
Symbol
Description
Reset
15:7
-
-
Reserved
0x0
6
R/W
I2C_SLAVE_DISABL
E
Slave enabled or disabled after reset is applied, which
means software does not have to configure the slave.
0=slave is enabled
1=slave is disabled
Software should ensure that if this bit is written with '0', then
bit 0 should also be written with a '0'.
0x1
5
R/W
I2C_RESTART_EN
Determines whether RESTART conditions may be sent
when acting as a master
0= disable
1=enable
0x1
4
R/W
I2C_10BITADDR_MA
STER
Controls whether the controller starts its transfers in 7- or 10bit addressing mode when acting as a master.
0= 7-bit addressing
1= 10-bit addressing
0x1
3
R/W
I2C_10BITADDR_SL
AVE
When acting as a slave, this bit controls whether the controller responds to 7- or 10-bit addresses.
0= 7-bit addressing
1= 10-bit addressing
0x1
2:1
R/W
I2C_SPEED
These bits control at which speed the controller operates.
1= standard mode (100 kbit/s)
2= fast mode (400 kbit/s)
0x2
0
R/W
I2C_MASTER_MOD
E
This bit controls whether the controller master is enabled.
0= master disabled
1= master enabled
Software should ensure that if this bit is written with '1' then
bit 6 should also be written with a '1'.
0x1
Table 133: I2C_TAR_REG (0x50001304)
Bit
Mode
Symbol
Description
Reset
15:12
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
97 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 133: I2C_TAR_REG (0x50001304)
Bit
Mode
Symbol
Description
Reset
11
R/W
SPECIAL
This bit indicates whether software performs a General Call
or
START BYTE command.
0: ignore bit 10 GC_OR_START and use IC_TAR normally
1: perform special I2C command as specified in
GC_OR_START
bit
0x0
10
R/W
GC_OR_START
If bit 11 (SPECIAL) is set to 1, then this bit indicates whether
a General Call or START byte command is to be performed
by the controller.
0: General Call Address - after issuing a General Call, only
writes may be performed. Attempting to issue a read command results in setting bit 6 (TX_ABRT) of the
IC_RAW_INTR_STAT register. The controller remains in
General Call mode until the SPECIAL bit value (bit 11) is
cleared.
1: START BYTE
0x0
9:0
R/W
IC_TAR
This is the target address for any master transaction. When
transmitting a General Call, these bits are ignored. To generate a START BYTE, the CPU needs to write only once into
these bits.
Note: If the IC_TAR and IC_SAR are the same, loopback
exists but the FIFOs are shared between master and slave,
so full loopback is not feasible. Only one direction loopback
mode is supported (simplex), not duplex. A master cannot
transmit to itself; it can transmit to only a slave
0x55
Description
Reset
Table 134: I2C_SAR_REG (0x50001308)
Bit
Mode
Symbol
15:10
-
-
Reserved
0x0
9:0
R/W
IC_SAR
The IC_SAR holds the slave address when the I2C is operating as a slave. For 7-bit addressing, only IC_SAR[6:0] is
used. This register can be written only when the I2C interface is disabled, which corresponds to the IC_ENABLE register being set to 0. Writes at other times have no effect.
0x55
Table 135: I2C_DATA_CMD_REG (0x50001310)
Bit
Mode
Symbol
Description
Reset
15:9
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
98 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 135: I2C_DATA_CMD_REG (0x50001310)
Bit
Mode
Symbol
Description
Reset
8
R/W
CMD
This bit controls whether a read or a write is performed. This
bit does not control the direction when the I2C Ctrl acts as a
slave. It controls only the direction when it acts as a master.
1 = Read
0 = Write
When a command is entered in the TX FIFO, this bit distinguishes the write and read commands. In slave-receiver
mode, this bit is a "don't care" because writes to this register
are not required. In slave-transmitter mode, a "0" indicates
that CPU data is to be transmitted and as DAT or
IC_DATA_CMD[7:0]. When programming this bit, you should
remember the following: attempting to perform a read operation after a General Call command has been sent results in a
TX_ABRT interrupt (bit 6 of the
I2C_RAW_INTR_STAT_REG), unless bit 11 (SPECIAL) in
the I2C_TAR register has been cleared.
If a "1" is written to this bit after receiving a RD_REQ interrupt, then a TX_ABRT interrupt occurs.
NOTE: It is possible that while attempting a master I2C read
transfer on the controller, a RD_REQ interrupt may have
occurred simultaneously due to a remote I2C master
addressing the controller. In this type of scenario, it ignores
the I2C_DATA_CMD write, generates a TX_ABRT interrupt,
and waits to service the RD_REQ interrupt
0x0
7:0
R/W
DAT
This register contains the data to be transmitted or received
on the I2C bus. If you are writing to this register and want to
perform a read, bits 7:0 (DAT) are ignored by the controller.
However, when you read this register, these bits return the
value of data received on the controller's interface.
0x0
Table 136: I2C_SS_SCL_HCNT_REG (0x50001314)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IC_SS_SCL_HCNT
This register must be set before any I2C bus transaction can
take place to ensure proper I/O timing. This register sets the
SCL clock high-period count for standard speed. This register can be written only when the I2C interface is disabled
which corresponds to the IC_ENABLE register being set to
0. Writes at other
times have no effect.
The minimum valid value is 6; hardware prevents values less
than this being written, and if attempted results in 6 being
set.
NOTE: This register must not be programmed to a value
higher than 65525, because the controller uses a 16-bit
counter to flag an I2C bus idle condition when this counter
reaches a value of IC_SS_SCL_HCNT + 10.
0x48
Datasheet
CFR0011-120-01
Revision 3.4
99 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 137: I2C_SS_SCL_LCNT_REG (0x50001318)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IC_SS_SCL_LCNT
This register must be set before any I2C bus transaction can
take place to ensure proper I/O timing. This register sets the
SCL clock low period count for standard speed.
This register can be written only when the I2C interface is
disabled which corresponds to the I2C_ENABLE register
being set to 0. Writes at other times have no effect.
The minimum valid value is 8; hardware prevents values less
than this being written, and if attempted, results in 8 being
set.
0x4F
Table 138: I2C_FS_SCL_HCNT_REG (0x5000131C)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IC_FS_SCL_HCNT
This register must be set before any I2C bus transaction can
take place to ensure proper I/O timing. This register sets the
SCL clock high-period count for fast speed. It is used in highspeed mode to send the Master Code and START BYTE or
General CALL. This register can be written only when the
I2C interface is disabled, which corresponds to the
I2C_ENABLE register being set to 0. Writes at other times
have no effect.
The minimum valid value is 6; hardware prevents values less
than this being written, and if attempted results in 6 being
set.
0x8
Table 139: I2C_FS_SCL_LCNT_REG (0x50001320)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IC_FS_SCL_LCNT
This register must be set before any I2C bus transaction can
take place to ensure proper I/O timing. This register sets the
SCL clock low-period count for fast speed. It is used in highspeed mode to send the Master Code and START BYTE or
General CALL. This register can be written only when the
I2C interface is disabled, which corresponds to the
I2C_ENABLE register being set to 0. Writes at other times
have no effect.
The minimum valid value is 8; hardware prevents values less
than this being written, and if attempted results in 8 being
set. For designs with APB_DATA_WIDTH = 8 the order of
programming is important to ensure the correct operation of
the controller. The lower byte must be programmed first.
Then the upper byte is programmed.
0x17
Table 140: I2C_INTR_STAT_REG (0x5000132C)
Bit
Mode
Symbol
15:12
-
11
R
Datasheet
CFR0011-120-01
Description
Reset
-
Reserved
0x0
R_GEN_CALL
Set only when a General Call address is received and it is
acknowledged. It stays set until it is cleared either by disabling controller or when the CPU reads bit 0 of the
I2C_CLR_GEN_CALL register. The controller stores the
received data in the Rx buffer.
0x0
Revision 3.4
100 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 140: I2C_INTR_STAT_REG (0x5000132C)
Bit
Mode
Symbol
Description
Reset
10
R
R_START_DET
Indicates whether a START or RESTART condition has
occurred on the I2C interface regardless of whether controller is operating in slave or master mode.
0x0
9
R
R_STOP_DET
Indicates whether a STOP condition has occurred on the I2C
interface regardless of whether controller is operating in
slave or master mode.
0x0
8
R
R_ACTIVITY
This bit captures I2C Ctrl activity and stays set until it is
cleared. There are four ways to clear it:
=> Disabling the I2C Ctrl
=> Reading the IC_CLR_ACTIVITY register
=> Reading the IC_CLR_INTR register
=> System reset
Once this bit is set, it stays set unless one of the four methods is used to clear it. Even if the controller module is idle,
this bit remains set until cleared, indicating that there was
activity on the bus.
0x0
7
R
R_RX_DONE
When the controller is acting as a slave-transmitter, this bit is
set to 1 if the master does not acknowledge a transmitted
byte. This occurs on the last byte of the transmission, indicating that the transmission is done.
0x0
6
R
R_TX_ABRT
This bit indicates if the controller, as an I2C transmitter, is
unable to complete the intended actions on the contents of
the transmit FIFO. This situation can occur both as an I2C
master or an I2C slave, and is referred to as a "transmit
abort".
When this bit is set to 1, the I2C_TX_ABRT_SOURCE register indicates the reason why the transmit abort takes places.
NOTE: The controller flushes/resets/empties the TX FIFO
whenever this bit is set. The TX FIFO remains in this flushed
state until the register I2C_CLR_TX_ABRT is read. Once
this read is performed, the TX FIFO is then ready to accept
more data bytes from the APB interface.
0x0
5
R
R_RD_REQ
This bit is set to 1 when the controller is acting as a slave
and another I2C master is attempting to read data from the
controller. The controller holds the I2C bus in a wait state
(SCL=0) until this interrupt is serviced, which means that the
slave has been addressed by a remote master that is asking
for data to be transferred. The processor must respond to
this interrupt and then write the requested data to the
I2C_DATA_CMD register. This bit is set to 0 just after the
processor reads the I2C_CLR_RD_REQ register
0x0
4
R
R_TX_EMPTY
This bit is set to 1 when the transmit buffer is at or below the
threshold value set in the I2C_TX_TL register. It is automatically cleared by hardware when the buffer level goes above
the threshold. When the IC_ENABLE bit 0 is 0, the TX FIFO
is flushed and held in reset. There the TX FIFO looks like it
has no data within it, so this bit is set to 1, provided there is
activity in the master or slave state machines. When there is
no longer activity, then with ic_en=0, this bit is set to 0.
0x0
3
R
R_TX_OVER
Set during transmit if the transmit buffer is filled to 32 and the
processor attempts to issue another I2C command by writing
to the IC_DATA_CMD register. When the module is disabled,
this bit keeps its level until the master or slave state
machines go into idle, and when ic_en goes to 0, this interrupt is cleared
0x0
Datasheet
CFR0011-120-01
Revision 3.4
101 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 140: I2C_INTR_STAT_REG (0x5000132C)
Bit
Mode
Symbol
Description
Reset
2
R
R_RX_FULL
Set when the receive buffer reaches or goes above the
RX_TL threshold in the I2C_RX_TL register. It is automatically cleared by hardware when buffer level goes below the
threshold. If the module is disabled (I2C_ENABLE[0]=0), the
RX FIFO is flushed and held in reset; therefore the RX FIFO
is not full. So this bit is cleared once the I2C_ENABLE bit 0 is
programmed with a 0, regardless of the activity that continues.
0x0
1
R
R_RX_OVER
Set if the receive buffer is completely filled to 32 and an additional byte is received from an external I2C device. The controller acknowledges this, but any data bytes received after
the FIFO is full are lost. If the module is disabled
(I2C_ENABLE[0]=0), this bit keeps its level until the master
or slave state machines go into idle, and when ic_en goes to
0, this interrupt is cleared.
0x0
0
R
R_RX_UNDER
Set if the processor attempts to read the receive buffer when
it is empty by reading from the IC_DATA_CMD register. If the
module is disabled (I2C_ENABLE[0]=0), this bit keeps its
level until the master or slave state machines go into idle,
and when ic_en goes to 0, this interrupt is cleared.
0x0
Table 141: I2C_INTR_MASK_REG (0x50001330)
Bit
Mode
Symbol
Description
Reset
15:12
-
-
Reserved
0x0
11
R/W
M_GEN_CALL
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
10
R/W
M_START_DET
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x0
9
R/W
M_STOP_DET
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x0
8
R/W
M_ACTIVITY
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x0
7
R/W
M_RX_DONE
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
6
R/W
M_TX_ABRT
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
5
R/W
M_RD_REQ
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
4
R/W
M_TX_EMPTY
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
3
R/W
M_TX_OVER
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
2
R/W
M_RX_FULL
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
1
R/W
M_RX_OVER
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
0
R/W
M_RX_UNDER
These bits mask their corresponding interrupt status bits in
the I2C_INTR_STAT register.
0x1
Datasheet
CFR0011-120-01
Revision 3.4
102 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 142: I2C_RAW_INTR_STAT_REG (0x50001334)
Bit
Mode
Symbol
Description
Reset
15:12
-
11
R
-
Reserved
0x0
GEN_CALL
Set only when a General Call address is received and it is
acknowledged. It stays set until it is cleared either by disabling controller or when the CPU reads bit 0 of the
I2C_CLR_GEN_CALL register. I2C Ctrl stores the received
data in the Rx buffer.
0x0
10
R
START_DET
Indicates whether a START or RESTART condition has
occurred on the I2C interface regardless of whether controller is operating in slave or master mode.
0x0
9
R
STOP_DET
Indicates whether a STOP condition has occurred on the I2C
interface regardless of whether controller is operating in
slave or master mode.
0x0
8
R
ACTIVITY
This bit captures I2C Ctrl activity and stays set until it is
cleared. There are four ways to clear it:
=> Disabling the I2C Ctrl
=> Reading the IC_CLR_ACTIVITY register
=> Reading the IC_CLR_INTR register
=> System reset
Once this bit is set, it stays set unless one of the four methods is used to clear it. Even if the controller module is idle,
this bit remains set until cleared, indicating that there was
activity on the bus.
0x0
7
R
RX_DONE
When the controller is acting as a slave-transmitter, this bit is
set to 1 if the master does not acknowledge a transmitted
byte. This occurs on the last byte of the transmission, indicating that the transmission is done.
0x0
6
R
TX_ABRT
This bit indicates if the controller, as an I2C transmitter, is
unable to complete the intended actions on the contents of
the transmit FIFO. This situation can occur both as an I2C
master or an I2C slave, and is referred to as a "transmit
abort".
When this bit is set to 1, the I2C_TX_ABRT_SOURCE register indicates the reason why the transmit abort takes places.
NOTE: The controller flushes/resets/empties the TX FIFO
whenever this bit is set. The TX FIFO remains in this flushed
state until the register I2C_CLR_TX_ABRT is read. Once
this read is performed, the TX FIFO is then ready to accept
more data bytes from the APB interface.
0x0
5
R
RD_REQ
This bit is set to 1 when I2C Ctrl is acting as a slave and
another I2C master is attempting to read data from the controller. The controller holds the I2C bus in a wait state
(SCL=0) until this interrupt is serviced, which means that the
slave has been addressed by a remote master that is asking
for data to be transferred. The processor must respond to
this interrupt and then write the requested data to the
I2C_DATA_CMD register. This bit is set to 0 just after the
processor reads the I2C_CLR_RD_REQ register
0x0
4
R
TX_EMPTY
This bit is set to 1 when the transmit buffer is at or below the
threshold value set in the I2C_TX_TL register. It is automatically cleared by hardware when the buffer level goes above
the threshold. When the IC_ENABLE bit 0 is 0, the TX FIFO
is flushed and held in reset. There the TX FIFO looks like it
has no data within it, so this bit is set to 1, provided there is
activity in the master or slave state machines. When there is
no longer activity, then with ic_en=0, this bit is set to 0.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
103 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 142: I2C_RAW_INTR_STAT_REG (0x50001334)
Bit
Mode
Symbol
Description
Reset
3
R
TX_OVER
Set during transmit if the transmit buffer is filled to 32 and the
processor attempts to issue another I2C command by writing
to the IC_DATA_CMD register. When the module is disabled,
this bit keeps its level until the master or slave state
machines go into idle, and when ic_en goes to 0, this interrupt is cleared
0x0
2
R
RX_FULL
Set when the receive buffer reaches or goes above the
RX_TL threshold in the I2C_RX_TL register. It is automatically cleared by hardware when buffer level goes below the
threshold. If the module is disabled (I2C_ENABLE[0]=0), the
RX FIFO is flushed and held in reset; therefore the RX FIFO
is not full. So this bit is cleared once the I2C_ENABLE bit 0 is
programmed with a 0, regardless of the activity that continues.
0x0
1
R
RX_OVER
Set if the receive buffer is completely filled to 32 and an additional byte is received from an external I2C device. The controller acknowledges this, but any data bytes received after
the FIFO is full are lost. If the module is disabled
(I2C_ENABLE[0]=0), this bit keeps its level until the master
or slave state machines go into idle, and when ic_en goes to
0, this interrupt is cleared.
0x0
0
R
RX_UNDER
Set if the processor attempts to read the receive buffer when
it is empty by reading from the IC_DATA_CMD register. If the
module is disabled (I2C_ENABLE[0]=0), this bit keeps its
level until the master or slave state machines go into idle,
and when ic_en goes to 0, this interrupt is cleared.
0x0
Table 143: I2C_RX_TL_REG (0x50001338)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
4:0
R/W
RX_TL
Receive FIFO Threshold Level Controls the level of entries
(or above) that triggers the RX_FULL interrupt (bit 2 in
I2C_RAW_INTR_STAT register). The valid range is 0-31,
with the additional restriction that hardware does not allow
this value to be set to a value larger than the depth of the
buffer. If an attempt is made to do that, the actual value set
will be the maximum depth of the buffer. A value of 0 sets the
threshold for 1 entry, and a value of 31 sets the threshold for
32 entries.
0x0
Table 144: I2C_TX_TL_REG (0x5000133C)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
4:0
R/W
RX_TL
Transmit FIFO Threshold Level Controls the level of entries
(or below) that trigger the TX_EMPTY interrupt (bit 4 in
I2C_RAW_INTR_STAT register). The valid range is 0-31,
with the additional restriction that it may not be set to value
larger than the depth of the buffer. If an attempt is made to
do that, the actual value set will be the maximum depth of
the buffer. A value of 0 sets the threshold for 0 entries, and a
value of 31 sets the threshold for 32 entries..
0x0
Datasheet
CFR0011-120-01
Revision 3.4
104 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 145: I2C_CLR_INTR_REG (0x50001340)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_INTR
Read this register to clear the combined interrupt, all individual interrupts, and the I2C_TX_ABRT_SOURCE register.
This bit does not clear hardware clearable interrupts but software clearable interrupts. Refer to Bit 9 of the
I2C_TX_ABRT_SOURCE register for an exception to clearing I2C_TX_ABRT_SOURCE
0x0
Table 146: I2C_CLR_RX_UNDER_REG (0x50001344)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_RX_UNDER
Read this register to clear the RX_UNDER interrupt (bit 0) of
the
I2C_RAW_INTR_STAT register.
0x0
Table 147: I2C_CLR_RX_OVER_REG (0x50001348)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_RX_OVER
Read this register to clear the RX_OVER interrupt (bit 1) of
the
I2C_RAW_INTR_STAT register.
0x0
Table 148: I2C_CLR_TX_OVER_REG (0x5000134C)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_TX_OVER
Read this register to clear the TX_OVER interrupt (bit 3) of
the I2C_RAW_INTR_STAT register.
0x0
Table 149: I2C_CLR_RD_REQ_REG (0x50001350)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_RD_REQ
Read this register to clear the RD_REQ interrupt (bit 5) of
the I2C_RAW_INTR_STAT register.
0x0
Table 150: I2C_CLR_TX_ABRT_REG (0x50001354)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_TX_ABRT
Read this register to clear the TX_ABRT interrupt (bit 6) of
the
IC_RAW_INTR_STAT register, and the
I2C_TX_ABRT_SOURCE register. This also releases the TX
FIFO from the flushed/reset state, allowing more writes to
the TX FIFO. Refer to Bit 9 of the I2C_TX_ABRT_SOURCE
register for an exception to clearing
IC_TX_ABRT_SOURCE.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
105 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 151: I2C_CLR_RX_DONE_REG (0x50001358)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_RX_DONE
Read this register to clear the RX_DONE interrupt (bit 7) of
the
I2C_RAW_INTR_STAT register.
0x0
Table 152: I2C_CLR_ACTIVITY_REG (0x5000135C)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_ACTIVITY
Reading this register clears the ACTIVITY interrupt if the I2C
is not active anymore. If the I2C module is still active on the
bus, the ACTIVITY interrupt bit continues to be set. It is automatically cleared by hardware if the module is disabled and if
there is no further activity on the bus. The value read from
this register to get status of the ACTIVITY interrupt (bit 8) of
the IC_RAW_INTR_STAT register
0x0
Table 153: I2C_CLR_STOP_DET_REG (0x50001360)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_ACTIVITY
Reading this register clears the ACTIVITY interrupt if the I2C
is not active anymore. If the I2C module is still active on the
bus, the ACTIVITY interrupt bit continues to be set. It is automatically cleared by hardware if the module is disabled and if
there is no further activity on the bus. The value read from
this register to get status of the ACTIVITY interrupt (bit 8) of
the IC_RAW_INTR_STAT register.
0x0
Table 154: I2C_CLR_START_DET_REG (0x50001364)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_START_DET
Read this register to clear the START_DET interrupt (bit 10)
of the IC_RAW_INTR_STAT register.
0x0
Table 155: I2C_CLR_GEN_CALL_REG (0x50001368)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R
CLR_GEN_CALL
Read this register to clear the GEN_CALL interrupt (bit 11) of
I2C_RAW_INTR_STAT register.
0x0
Table 156: I2C_ENABLE_REG (0x5000136C)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
106 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 156: I2C_ENABLE_REG (0x5000136C)
Bit
Mode
Symbol
Description
Reset
0
R/W
CTRL_ENABLE
Controls whether the controller is enabled.
0: Disables the controller (TX and RX FIFOs are held in an
erased state)
1: Enables the controller
Software can disable the controller while it is active. However, it is important that care be taken to ensure that the controller is disabled properly. When the controller is disabled,
the following occurs:
* The TX FIFO and RX FIFO get flushed.
* Status bits in the IC_INTR_STAT register are still active
until the controller goes into IDLE state.
If the module is transmitting, it stops as well as deletes the
contents of the transmit buffer after the current transfer is
complete. If the module is receiving, the controller stops the
current transfer at the end of the current byte and does not
acknowledge the transfer.
There is a two ic_clk delay when enabling or disabling the
controller
0x0
Table 157: I2C_STATUS_REG (0x50001370)
Bit
Mode
Symbol
Description
Reset
15:7
-
-
Reserved
0x0
6
R
SLV_ACTIVITY
Slave FSM Activity Status. When the Slave Finite State
Machine (FSM) is not in the IDLE state, this bit is set.
0: Slave FSM is in IDLE state so the Slave part of the controller is not Active
1: Slave FSM is not in IDLE state so the Slave part of the
controller is Active
0x0
5
R
MST_ACTIVITY
Master FSM Activity Status. When the Master Finite State
Machine (FSM) is not in the IDLE state, this bit is set.
0: Master FSM is in IDLE state so the Master part of the controller is not Active
1: Master FSM is not in IDLE state so the Master part of the
controller is Active
0x0
4
R
RFF
Receive FIFO Completely Full. When the receive FIFO is
completely full, this bit is set. When the receive FIFO contains one or more empty location, this bit is cleared.
0: Receive FIFO is not full
1: Receive FIFO is full
0x0
3
R
RFNE
Receive FIFO Not Empty. This bit is set when the receive
FIFO contains one or more entries; it is cleared when the
receive FIFO is empty.
0: Receive FIFO is empty
1: Receive FIFO is not empty
0x0
2
R
TFE
Transmit FIFO Completely Empty. When the transmit FIFO is
completely empty, this bit is set. When it contains one or
more valid entries, this bit is cleared. This bit field does not
request an interrupt.
0: Transmit FIFO is not empty
1: Transmit FIFO is empty
0x1
1
R
TFNF
Transmit FIFO Not Full. Set when the transmit FIFO contains
one or more empty locations, and is cleared when the FIFO
is full.
0: Transmit FIFO is full
1: Transmit FIFO is not full
0x1
Datasheet
CFR0011-120-01
Revision 3.4
107 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 157: I2C_STATUS_REG (0x50001370)
Bit
Mode
Symbol
Description
Reset
0
R
I2C_ACTIVITY
I2C Activity Status.
0x0
Table 158: I2C_TXFLR_REG (0x50001374)
Bit
Mode
Symbol
Description
Reset
15:6
-
-
Reserved
0x0
5:0
R
TXFLR
Transmit FIFO Level. Contains the number of valid data
entries in the transmit FIFO. Size is constrained by the
TXFLR value
0x0
Table 159: I2C_RXFLR_REG (0x50001378)
Bit
Mode
Symbol
Description
Reset
15:6
-
-
Reserved
0x0
5:0
R
RXFLR
Receive FIFO Level. Contains the number of valid data
entries in the receive FIFO. Size is constrained by the
RXFLR value
0x0
Table 160: I2C_SDA_HOLD_REG (0x5000137C)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
IC_SDA_HOLD
SDA Hold time
0x1
Table 161: I2C_TX_ABRT_SOURCE_REG (0x50001380)
Bit
Mode
Symbol
Description
Reset
15
R
ABRT_SLVRD_INTX
1: When the processor side responds to a slave mode
request for data to be transmitted to a remote master and
user writes a 1 in CMD (bit 8) of 2IC_DATA_CMD register
0x0
14
R
ABRT_SLV_ARBLOS
T
1: Slave lost the bus while transmitting data to a remote
master.
I2C_TX_ABRT_SOURCE[12] is set at the same time. Note:
Even though the slave never "owns" the bus, something
could go wrong on the bus. This is a fail safe check. For
instance, during a data transmission at the low-to-high transition of SCL, if what is on the data bus is not what is supposed to be transmitted, then the controller no longer own
the bus.
0x0
13
R
ABRT_SLVFLUSH_T
XFIFO
1: Slave has received a read command and some data
exists in the TX FIFO so the slave issues a TX_ABRT interrupt to flush old data in TX FIFO.
0x0
12
R
ARB_LOST
1: Master has lost arbitration, or if
I2C_TX_ABRT_SOURCE[14] is also set, then the slave
transmitter has lost arbitration. Note: I2C can be both master
and slave at the same time.
0x0
11
R
ABRT_MASTER_DIS
1: User tries to initiate a Master operation with the Master
mode disabled.
0x0
10
R
ABRT_10B_RD_NO
RSTRT
1: The restart is disabled (IC_RESTART_EN bit
(I2C_CON[5]) = 0) and the master sends a read command in
10-bit addressing mode.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
108 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 161: I2C_TX_ABRT_SOURCE_REG (0x50001380)
Bit
Mode
Symbol
Description
Reset
9
R
ABRT_SBYTE_NOR
STRT
To clear Bit 9, the source of the ABRT_SBYTE_NORSTRT
must be fixed first; restart must be enabled (I2C_CON[5]=1),
the SPECIAL bit must be cleared (I2C_TAR[11]), or the
GC_OR_START bit must be cleared (I2C_TAR[10]). Once
the source of the ABRT_SBYTE_NORSTRT is fixed, then
this bit can be cleared in the same manner as other bits in
this register. If the source of the ABRT_SBYTE_NORSTRT
is not fixed before attempting to clear this bit, bit 9 clears for
one cycle and then gets re-asserted. 1: The restart is disabled (IC_RESTART_EN bit (I2C_CON[5]) = 0) and the user
is trying to send a START Byte.
0x0
8
R
ABRT_HS_NORSTR
T
1: The restart is disabled (IC_RESTART_EN bit
(I2C_CON[5]) = 0) and the user is trying to use the master to
transfer data in High Speed mode
0x0
7
R
ABRT_SBYTE_ACK
DET
1: Master has sent a START Byte and the START Byte was
acknowledged (wrong behavior).
0x0
6
R
ABRT_HS_ACKDET
1: Master is in High Speed mode and the High Speed Master
code was acknowledged (wrong behavior).
0x0
5
R
ABRT_GCALL_REA
D
1: the controller in master mode sent a General Call but the
user programmed the byte following the General Call to be a
read from the bus (IC_DATA_CMD[9] is set to 1).
0x0
4
R
ABRT_GCALL_NOA
CK
1: the controller in master mode sent a General Call and no
slave on the bus acknowledged the General Call.
0x0
3
R
ABRT_TXDATA_NO
ACK
1: This is a master-mode only bit. Master has received an
acknowledgement for the address, but when it sent data
byte(s) following the address, it did not receive an acknowledge from the remote slave(s).
0x0
2
R
ABRT_10ADDR2_N
OACK
1: Master is in 10-bit address mode and the second address
byte of the 10-bit address was not acknowledged by any
slave.
0x0
1
R
ABRT_10ADDR1_N
OACK
1: Master is in 10-bit address mode and the first 10-bit
address byte was not acknowledged by any slave.
0x0
0
R
ABRT_7B_ADDR_N
OACK
1: Master is in 7-bit addressing mode and the address sent
was not acknowledged by any slave.
0x0
Table 162: I2C_SDA_SETUP_REG (0x50001394)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
SDA_SETUP
SDA Setup.
This register controls the amount of time delay (number of
I2C clock periods) between the rising edge of SCL and SDA
changing by holding SCL low when I2C block services a
read request while operating as a slave-transmitter. The relevant I2C requirement is tSU:DAT (note 4) as detailed in the
I2C Bus Specification. This register must be programmed
with a value equal to or greater than 2.
It is recommended that if the required delay is 1000ns, then
for an I2C frequency of 10 MHz, IC_SDA_SETUP should be
programmed to a value of 11.Writes to this register succeed
only when IC_ENABLE[0] = 0.
0x64
Datasheet
CFR0011-120-01
Revision 3.4
109 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 163: I2C_ACK_GENERAL_CALL_REG (0x50001398)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
ACK_GEN_CALL
ACK General Call. When set to 1, I2C Ctrl responds with a
ACK (by asserting ic_data_oe) when it receives a General
Call. When set to 0, the controller does not generate General
Call interrupts.
0x0
Table 164: I2C_ENABLE_STATUS_REG (0x5000139C)
Bit
Mode
Symbol
Description
Reset
15:3
-
-
Reserved
0x0
2
R
SLV_RX_DATA_LOS
T
Slave Received Data Lost. This bit indicates if a SlaveReceiver
operation has been aborted with at least one data byte
received from an I2C transfer due to the setting of
IC_ENABLE from 1 to 0. When read as 1, the controller is
deemed to have been actively engaged in an aborted I2C
transfer (with matching address) and the data phase of the
I2C transfer has been entered, even though a data byte has
been responded with a NACK. NOTE: If the remote I2C master terminates the transfer with a STOP condition before the
controller has a chance to NACK a transfer, and IC_ENABLE
has been set to 0, then this bit is also set to 1.
When read as 0, the controller is deemed to have been disabled without being actively involved in the data phase of a
Slave-Receiver transfer.
NOTE: The CPU can safely read this bit when IC_EN (bit 0)
is read as 0.
0x0
1
R
SLV_DISABLED_WH
ILE_BUSY
Slave Disabled While Busy (Transmit, Receive). This bit indicates if a potential or active Slave operation has been
aborted due to the setting of the IC_ENABLE register from 1
to 0. This bit is set when the CPU writes a 0 to the
IC_ENABLE register while:
(a) I2C Ctrl is receiving the address byte of the Slave-Transmitter operation from a remote master; OR,
(b) address and data bytes of the Slave-Receiver operation
from a remote master. When read as 1, the controller is
deemed to have forced a NACK during any part of an I2C
transfer, irrespective of whether the I2C address matches
the slave address set in I2C Ctrl (IC_SAR register) OR if the
transfer is completed before IC_ENABLE is set to 0 but has
not taken effect.
NOTE: If the remote I2C master terminates the transfer with
a STOP condition before the the controller has a chance to
NACK a transfer, and IC_ENABLE has been set to 0, then
this bit will also be set to 1.
When read as 0, the controller is deemed to have been disabled when there is master activity, or when the I2C bus is
idle.
NOTE: The CPU can safely read this bit when IC_EN (bit 0)
is read as 0.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
110 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 164: I2C_ENABLE_STATUS_REG (0x5000139C)
Bit
Mode
Symbol
Description
Reset
0
R
IC_EN
ic_en Status. This bit always reflects the value driven on the
output port ic_en. When read as 1, the controller is deemed
to be in an enabled state.
When read as 0, the controller is deemed completely inactive.
NOTE: The CPU can safely read this bit anytime. When this
bit is read as 0, the CPU can safely read
SLV_RX_DATA_LOST (bit 2) and
SLV_DISABLED_WHILE_BUSY (bit 1).
0x0
Table 165: I2C_IC_FS_SPKLEN_REG (0x500013A0)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
IC_FS_SPKLEN
This register must be set before any I2C bus transaction can
take place to ensure stable operation. This register sets the
duration, measured in ic_clk cycles, of the longest spike in
the SCL or SDA lines that will be filtered out by the spike
suppression logic. This register can be written only when the
I2C interface is disabled which corresponds to the
IC_ENABLE register being set to 0. Writes at other times
have no effect. The minimum valid value is 2; hardware prevents values less than this being written, and if attempted
results in 2 being set.
0x1
Table 166: GPIO_IRQ0_IN_SEL_REG (0x50001400)
Bit
Mode
Symbol
Description
Reset
15:6
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
111 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 166: GPIO_IRQ0_IN_SEL_REG (0x50001400)
Bit
Mode
Symbol
Description
Reset
5:0
R/W
KBRD_IRQ0_SEL
input selection that can generate a GPIO interrupt
0: no input selected
1: P0[0] is selected
2: P0[1] is selected
3: P0[2] is selected
4: P0[3] is selected
5: P0[4] is selected
6: P0[5] is selected
7: P0[6] is selected
8: P0[7] is selected
9: P1[0] is selected
10: P1[1] is selected
11: P1[2] is selected
12: P1[3] is selected
13: P1[4] is selected
14: P1[5] is selected
15: P2[0] is selected
16: P2[1] is selected
17: P2[2] is selected
18: P2[3] is selected
19: P2[4] is selected
20: P2[5] is selected
21: P2[6] is selected
22: P2[7] is selected
23: P2[8] is selected
24: P2[9] is selected
25: P3[0] is selected
26: P3[1] is selected
27: P3[2] is selected
28: P3[3] is selected
29: P3[4] is selected
30: P3[5] is selected
31: P3[6] is selected
32: P3[7] is selected
all others: no input selected
0x0
Table 167: GPIO_IRQ1_IN_SEL_REG (0x50001402)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
5:0
R/W
KBRD_IRQ1_SEL
see KBRD_IRQ0_SEL
0x0
Table 168: GPIO_IRQ2_IN_SEL_REG (0x50001404)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
5:0
R/W
KBRD_IRQ2_SEL
see KBRD_IRQ0_SEL
0x0
Table 169: GPIO_IRQ3_IN_SEL_REG (0x50001406)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
5:0
R/W
KBRD_IRQ3_SEL
see KBRD_IRQ0_SEL
0x0
Datasheet
CFR0011-120-01
Revision 3.4
112 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 170: GPIO_IRQ4_IN_SEL_REG (0x50001408)
Bit
Mode
Symbol
Description
Reset
15:5
-
-
Reserved
0x0
5:0
R/W
KBRD_IRQ4_SEL
see KBRD_IRQ0_SEL
0x0
Table 171: GPIO_DEBOUNCE_REG (0x5000140C)
Bit
Mode
Symbol
Description
Reset
15:14
-
-
Reserved
0x0
13
R/W
DEB_ENABLE_KBR
D
enables the debounce counter for the KBRD interface
0x0
12
R/W
DEB_ENABLE4
enables the debounce counter for GPIO IRQ4
0x0
11
R/W
DEB_ENABLE3
enables the debounce counter for GPIO IRQ3
0x0
10
R/W
DEB_ENABLE2
enables the debounce counter for GPIO IRQ2
0x0
9
R/W
DEB_ENABLE1
enables the debounce counter for GPIO IRQ1
0x0
8
R/W
DEB_ENABLE0
enables the debounce counter for GPIO IRQ0
0x0
7:6
-
-
Reserved
0x0
5:0
R/W
DEB_VALUE
Keyboard debounce time if enabled. Generate KEYB_INT
after specified time.
Debounce time: N*1 ms. N =0..63
0x0
Table 172: GPIO_RESET_IRQ_REG (0x5000140E)
Bit
Mode
Symbol
Description
Reset
15:6
-
-
Reserved
0x0
5
R0/W
RESET_KBRD_IRQ
writing a 1 to this bit will reset the KBRD IRQ.
Reading returns 0.
0x0
4
R0/W
RESET_GPIO4_IRQ
writing a 1 to this bit will reset the GPIO4 IRQ.
Reading returns 0.
0x0
3
R0/W
RESET_GPIO3_IRQ
writing a 1 to this bit will reset the GPIO3 IRQ.
Reading returns 0.
0x0
2
R0/W
RESET_GPIO2_IRQ
writing a 1 to this bit will reset the GPIO2 IRQ.
Reading returns 0.
0x0
1
R0/W
RESET_GPIO1_IRQ
writing a 1 to this bit will reset the GPIO1 IRQ.
Reading returns 0.
0x0
0
R0/W
RESET_GPIO0_IRQ
writing a 1 to this bit will reset the GPIO0 IRQ.
Reading returns 0.
0x0
Table 173: GPIO_INT_LEVEL_CTRL_REG (0x50001410)
Bit
Mode
15:14
-
12
R/W
11
R/W
10
R/W
9
8
7:6
Description
Reset
-
Reserved
0x0
EDGE_LEVELN4
see EDGE_LEVELn0, but for GPIO IRQ4
0x0
EDGE_LEVELN3
see EDGE_LEVELn0, but for GPIO IRQ3
0x0
EDGE_LEVELN2
see EDGE_LEVELn0, but for GPIO IRQ2
0x0
R/W
EDGE_LEVELN1
see EDGE_LEVELn0, but for GPIO IRQ1
0x0
R/W
EDGE_LEVELN0
0: do not wait for key release after interrupt was reset for
GPIO IRQ0, so a new interrupt can be initiated immediately
1: wait for key release after interrupt was reset for IRQ0
0x0
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Symbol
Revision 3.4
113 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 173: GPIO_INT_LEVEL_CTRL_REG (0x50001410)
Bit
Mode
Symbol
Description
Reset
4
R/W
INPUT_LEVEL4
see INPUT_LEVEL0, but for GPIO IRQ4
0x0
3
R/W
INPUT_LEVEL3
see INPUT_LEVEL0, but for GPIO IRQ3
0x0
2
R/W
INPUT_LEVEL2
see INPUT_LEVEL0, but for GPIO IRQ2
0x0
1
R/W
INPUT_LEVEL1
see INPUT_LEVEL0, but for GPIO IRQ1
0x0
0
R/W
INPUT_LEVEL0
0 = selected input will generate GPIO IRQ0 if that input is
high.
1 = selected input will generate GPIO IRQ0 if that input is
low.
0x0
Table 174: KBRD_IRQ_IN_SEL0_REG (0x50001412)
Bit
Mode
Symbol
Description
Reset
15
R/W
KBRD_REL
0 = No interrupt on key release
1 = Interrupt also on key release (also debouncing if
enabled)
0x0
14
R/W
KBRD_LEVEL
0 = enabled input will generate KBRD IRQ if that input is
high.
1 = enabled input will generate KBRD IRQ if that input is low.
0x0
13:8
R/W
KEY_REPEAT
While key is pressed, automatically generate repeating
KEYB_INT after specified time unequal to 0.
Repeat time: N*1 ms. N =1..63, N=0 disables the timer.
0x0
7
R/W
KBRD_P07_EN
enable P0[7] for the keyboard interrupt
0x0
6
R/W
KBRD_P06_EN
enable P0[6] for the keyboard interrupt
0x0
5
R/W
KBRD_P05_EN
enable P0[5] for the keyboard interrupt
0x0
4
R/W
KBRD_P04_EN
enable P0[4] for the keyboard interrupt
0x0
3
R/W
KBRD_P03_EN
enable P0[3] for the keyboard interrupt
0x0
2
R/W
KBRD_P02_EN
enable P0[2] for the keyboard interrupt
0x0
1
R/W
KBRD_P01_EN
enable P0[1] for the keyboard interrupt
0x0
0
R/W
KBRD_P00_EN
enable P0[0] for the keyboard interrupt
0x0
Table 175: KBRD_IRQ_IN_SEL1_REG (0x50001414)
Bit
Mode
Symbol
Description
Reset
15
R/W
KBRD_P15_EN
enable P1[5] for the keyboard interrupt
0x0
14
R/W
KBRD_P14_EN
enable P1[4] for the keyboard interrupt
0x0
13
R/W
KBRD_P13_EN
enable P1[3] for the keyboard interrupt
0x0
12
R/W
KBRD_P12_EN
enable P1[2] for the keyboard interrupt
0x0
11
R/W
KBRD_P11_EN
enable P1[1] for the keyboard interrupt
0x0
10
R/W
KBRD_P10_EN
enable P1[0] for the keyboard interrupt
0x0
9
R/W
KBRD_P29_EN
enable P2[9] for the keyboard interrupt
0x0
8
R/W
KBRD_P28_EN
enable P2[8] for the keyboard interrupt
0x0
7
R/W
KBRD_P27_EN
enable P2[7] for the keyboard interrupt
0x0
6
R/W
KBRD_P26_EN
enable P2[6] for the keyboard interrupt
0x0
5
R/W
KBRD_P25_EN
enable P2[5] for the keyboard interrupt
0x0
4
R/W
KBRD_P24_EN
enable P2[4] for the keyboard interrupt
0x0
3
R/W
KBRD_P23_EN
enable P2[3] for the keyboard interrupt
0x0
2
R/W
KBRD_P22_EN
enable P2[2] for the keyboard interrupt
0x0
Datasheet
CFR0011-120-01
Revision 3.4
114 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 175: KBRD_IRQ_IN_SEL1_REG (0x50001414)
Bit
Mode
Symbol
Description
Reset
1
R/W
KBRD_P21_EN
enable P2[1] for the keyboard interrupt
0x0
0
R/W
KBRD_P20_EN
enable P2[0] for the keyboard interrupt
0x0
Table 176: KBRD_IRQ_IN_SEL2_REG (0x50001416)
Bit
Mode
Symbol
Description
Reset
7
R/W
KBRD_P37_EN
enable P3[7] for the keyboard interrupt
0x0
6
R/W
KBRD_P36_EN
enable P3[6] for the keyboard interrupt
0x0
5
R/W
KBRD_P35_EN
enable P3[5] for the keyboard interrupt
0x0
4
R/W
KBRD_P34_EN
enable P3[4] for the keyboard interrupt
0x0
3
R/W
KBRD_P33_EN
enable P3[3] for the keyboard interrupt
0x0
2
R/W
KBRD_P32_EN
enable P3[2] for the keyboard interrupt
0x0
1
R/W
KBRD_P31_EN
enable P3[1] for the keyboard interrupt
0x0
0
R/W
KBRD_P30_EN
enable P3[0] for the keyboard interrupt
0x0
Table 177: GP_ADC_CTRL_REG (0x50001500)
Bit
Mode
Symbol
Description
Reset
15
R/W
GP_ADC_LDO_ZER
O
Forces LDO-output to 0V.
0x0
14
R/W
GP_ADC_LDO_EN
Turns on LDO.
0x0
13
R/W
GP_ADC_CHOP
Takes two samples with opposite GP_ADC_SIGN to cancel
the internal offset voltage of the ADC; Highly recommended
for DC-measurements.
0x0
12
R/W
GP_ADC_MUTE
Takes sample at mid-scale (to dertermine the internal offset
and/or noise of the ADC with regards to VDD_REF which is
also sampled by the ADC).
0x0
11
R/W
GP_ADC_SE
0 = Differential mode
1 = Single ended mode
0x0
10
R/W
GP_ADC_SIGN
0 = Default
1 = Conversion with opposite sign at input and output to cancel out the internal offset of the ADC and low-frequency
0x0
9:6
R/W
GP_ADC_SEL
ADC input selection which must be set before the
GP_ADC_START bit is enabled.
If GP_ADC_SE = 1 (single ended mode):
0000 = P0[0]
0001 = P0[1]
0010 = P0[2]
0011 = P0[3]
0100 = AVS
0101 = VDD_REF
0110 = VDD_RTT
0111 = VBAT3V
1000 = VDCDC
1001 = VBAT1V
All other combinations are reserved.
If GP_ADC_SE = 0 (differential mode):
0000 = P0[0] vs P0[1]
All other combinations are P0[2] vs P0[3].
0x0
5
R/W
GP_ADC_MINT
0 = Disable (mask) GP_ADC_INT.
1 = Enable GP_ADC_INT to ICU.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
115 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 177: GP_ADC_CTRL_REG (0x50001500)
Bit
Mode
Symbol
Description
Reset
4
R
GP_ADC_INT
1 = AD conversion ready and has generated an interrupt.
Must be cleared by writing any value to
GP_ADC_CLEAR_INT_REG.
0x0
3
R/W
GP_ADC_CLK_SEL
0 = Internal high-speed ADC clock used.
1 = Digital clock used.
0x0
2
-
GP_ADC_TEST
Reserved, keep 0.
0x0
1
R/W
GP_ADC_START
0 = ADC conversion ready.
1 = If a 1 is written, the ADC starts a conversion. After the
conversion this bit will be set to 0 and the GP_ADC_INT bit
will be set.
0x0
0
R/W
GP_ADC_EN
0 = ADC is disabled and in reset.
1 = ADC is enabled and sampling of input is started.
0x0
Table 178: GP_ADC_CTRL2_REG (0x50001502)
Bit
Mode
Symbol
Description
Reset
15:4
-
-
Reserved
0x0
3
R/W
GP_ADC_I20U
Adds 20uA constant load current at the ADC LDO to minimize ripple on the reference voltage of the ADC.
0x0
2
R/W
GP_ADC_IDYN
Enables dynamic load current at the ADC LDO to minimize
ripple on the reference voltage of the ADC.
0x0
1
R/W
GP_ADC_ATTN3X
0 = Input voltages up to 1.2V allowed.
1 = Input voltages up to 3.6V allowed by enabling 3x attenuator.
0x0
0
R/W
GP_ADC_DELAY_E
N
Enables delay function for several signals. This is not autocleared. Toggle this bit before every sampling to enable succesive conversions.
0x0
Table 179: GP_ADC_OFFP_REG (0x50001504)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:0
R/W
GP_ADC_OFFP
Offset adjust of 'positive' array of ADC-network (effective if
"GP_ADC_SE=0", or "GP_ADC_SE=1 AND
GP_ADC_SIGN=0")
0x200
Table 180: GP_ADC_OFFN_REG (0x50001506)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:0
R/W
GP_ADC_OFFN
Offset adjust of 'negative' array of ADC-network (effective if
"GP_ADC_SE=0", or "GP_ADC_SE=1 AND
GP_ADC_SIGN=1")
0x200
Table 181: GP_ADC_CLEAR_INT_REG (0x50001508)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
GP_ADC_CLR_INT
Writing any value to this register will clear the ADC_INT
interrupt. Reading returns 0.
0x0
Datasheet
CFR0011-120-01
Revision 3.4
116 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 182: GP_ADC_RESULT_REG (0x5000150A)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:0
R
GP_ADC_VAL
Returns the 10 bits linear value of the last AD conversion.
0x0
Table 183: GP_ADC_DELAY_REG (0x5000150C)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
DEL_LDO_EN
Defines the delay before the LDO enable
(GP_ADC_LDO_EN). Reset value is 0 µs since the LDO
enable should be the first thing to be programmed in the
sequence of bringing the GP ADC up.
0x0
Table 184: GP_ADC_DELAY2_REG (0x5000150E)
Bit
Mode
Symbol
Description
Reset
15:8
R/W
DEL_ADC_START
Defines the delay for the GP_ADC_START bit. Reset value
is 17 µs which is the recommended value to wait before
starting the GP ADC. This is the third and last step of bringing up the GP ADC
0x88
7:0
R/W
DEL_ADC_EN
Defines the delay for the GP_ADC_EN bit. Reset value is 16
µs which is the recommended value to wait after enabling
the LDO. This is the second step in bringing up the GP ADC.
0x80
Table 185: CLK_REF_SEL_REG (0x50001600)
Bit
Mode
Symbol
Description
Reset
15:3
-
-
Reserved
0x0
2
R/W
REF_CAL_START
Writing a '1' starts a calibration. This bit is cleared when calibration is finished, and CLK_REF_VAL is ready.
0x0
1:0
R/W
REF_CLK_SEL
Select clock input for calibration:
0x0 : RC32KHz oscillator
0x0
0x1 : RC16MHz oscillator
0x2 : XTAL32KHz oscillator
0x3 : RCX32KHz oscillator
Table 186: CLK_REF_CNT_REG (0x50001602)
Bit
Mode
Symbol
Description
Reset
15:0
R/W
REF_CNT_VAL
Indicates the calibration time, with a decrement counter to 1.
0x0
Table 187: CLK_REF_VAL_L_REG (0x50001604)
Bit
Mode
Symbol
Description
Reset
15:0
R
XTAL_CNT_VAL
Returns the lower 16 bits of XTAL16 clock cycles during the
calibration time, defined with REF_CNT_VAL
0x0
Datasheet
CFR0011-120-01
Revision 3.4
117 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 188: CLK_REF_VAL_H_REG (0x50001606)
Bit
Mode
Symbol
Description
Reset
15:0
R
XTAL_CNT_VAL
Returns the upper 16 bits of XTAL16 clock cycles during the
calibration time, defined with REF_CNT_VAL
0x0
Table 189: P0_DATA_REG (0x50003000)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
P0_DATA
Set P0 output register when written; Returns the value of P0
port when read
0x0
Table 190: P0_SET_DATA_REG (0x50003002)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
P0_SET
Writing a 1 to P0[y] sets P0[y] to 1. Writing 0 is discarded;
Reading returns 0
0x0
Table 191: P0_RESET_DATA_REG (0x50003004)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
P0_RESET
Writing a 1 to P0[y] sets P0[y] to 0. Writing 0 is discarded;
Reading returns 0
0x0
Table 192: P00_MODE_REG (0x50003006)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
118 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 192: P00_MODE_REG (0x50003006)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 193: P01_MODE_REG (0x50003008)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
119 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 193: P01_MODE_REG (0x50003008)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 194: P02_MODE_REG (0x5000300A)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
120 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 194: P02_MODE_REG (0x5000300A)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 195: P03_MODE_REG (0x5000300C)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
121 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 195: P03_MODE_REG (0x5000300C)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 196: P04_MODE_REG (0x5000300E)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
122 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 196: P04_MODE_REG (0x5000300E)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 197: P05_MODE_REG (0x50003010)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
123 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 197: P05_MODE_REG (0x50003010)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 198: P06_MODE_REG (0x50003012)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
124 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 198: P06_MODE_REG (0x50003012)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Table 199: P07_MODE_REG (0x50003014)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
125 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 199: P07_MODE_REG (0x50003014)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
Function of port
0 = Port function, PUPD as set above
1 = UART1_RX
2 = UART1_TX
3 = UART2_RX
4 = UART2_TX
5 = SPI_DI
6 = SPI_DO
7 = SPI_CLK
8 = SPI_EN
9 = I2C_SCL
10 = I2C_SDA
11 = UART1_IRDA_RX
12 = UART1_IRDA_TX
13 = UART2_IRDA_RX
14 = UART2_IRDA_TX
15 = ADC (only for P0[3:0])
16 = PWM0
17 = PWM1
18 = BLE_DIAG (only for P0[7:0])
19 = UART1_CTSN
20 = UART1_RTSN
21 = UART2_CTSN
22 = UART2_RTSN
23 = PWM2
24 = PWM3
25 = PWM4
Note: when a certain input function (like SPI_DI) is selected
on more than 1 port pin, the port with the lowest index has
the highest priority and P0 has higher priority than P1.
0x0
Description
Reset
Table 200: P1_DATA_REG (0x50003020)
Bit
Mode
Symbol
15:8
-
-
Reserved
0x0
7:0
R/W
P1_DATA
Set P1 output register when written; Returns the value of P1
port when read
0x0
Table 201: P1_SET_DATA_REG (0x50003022)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
P1_SET
Writing a 1 to P1[y] sets P1[y] to 1. Writing 0 is discarded;
Reading returns 0
0x0
Table 202: P1_RESET_DATA_REG (0x50003024)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0x0
7:0
R/W
P1_RESET
Writing a 1 to P1[y] sets P1[y] to 0. Writing 0 is discarded;
Reading returns 0
0x0
Datasheet
CFR0011-120-01
Revision 3.4
126 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 203: P10_MODE_REG (0x50003026)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
P14_MODE_REG and P15_MODE_REG reset value is 1
(i.e. pulled up)
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 204: P11_MODE_REG (0x50003028)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
P14_MODE_REG and P15_MODE_REG reset value is 1
(i.e. pulled up)
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 205: P12_MODE_REG (0x5000302A)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
P14_MODE_REG and P15_MODE_REG reset value is 1
(i.e. pulled up)
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 206: P13_MODE_REG (0x5000302C)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
P14_MODE_REG and P15_MODE_REG reset value is 1
(i.e. pulled up)
0x2
7:5
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
127 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 206: P13_MODE_REG (0x5000302C)
Bit
Mode
Symbol
Description
Reset
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 207: P14_MODE_REG (0x5000302E)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
P14_MODE_REG and P15_MODE_REG reset value is 1
(i.e. pulled up)
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 208: P15_MODE_REG (0x50003030)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
P14_MODE_REG and P15_MODE_REG reset value is 1
(i.e. pulled up)
0x1
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Description
Reset
Table 209: P2_DATA_REG (0x50003040)
Bit
Mode
Symbol
15:10
-
-
Reserved
0x0
9:0
R/W
P2_DATA
Set P2 output register when written; Returns the value of P2
port when read
0x0
Table 210: P2_SET_DATA_REG (0x50003042)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:0
R/W
P2_SET
Writing a 1 to P2[y] sets P2[y] to 1. Writing 0 is discarded;
Reading returns 0
0x0
Table 211: P2_RESET_DATA_REG (0x50003044)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:0
R/W
P2_RESET
Writing a 1 to P2[y] sets P2[y] to 0. Writing 0 is discarded;
Reading returns 0
0x0
Datasheet
CFR0011-120-01
Revision 3.4
128 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 212: P20_MODE_REG (0x50003046)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 213: P21_MODE_REG (0x50003048)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 214: P22_MODE_REG (0x5000304A)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 215: P23_MODE_REG (0x5000304C)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 216: P24_MODE_REG (0x5000304E)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
129 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 216: P24_MODE_REG (0x5000304E)
Bit
Mode
Symbol
Description
Reset
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 217: P25_MODE_REG (0x50003050)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 218: P26_MODE_REG (0x50003052)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 219: P27_MODE_REG (0x50003054)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 220: P28_MODE_REG (0x50003056)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
130 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 220: P28_MODE_REG (0x50003056)
Bit
Mode
Symbol
Description
Reset
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 221: P29_MODE_REG (0x50003058)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In analog mode, these bits are don't care
0x2
7:5
-
-
Reserved
0x0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0x0
Table 222: P01_PADPWR_CTRL_REG (0x50003070)
Bit
Mode
15:12
13:8
7:0
Note 3:
Symbol
Description
Reset
-
-
Reserved
0x0
R/W
P1_OUT_CTRL
1 = P1_x port output is powered by the 1 V rail
0 = P1_x port output is powered by the 3 V rail
bit 8 controls the power of P1[0],
bit 13 controls the power of P1[5]
(Note 3)
0x0
R/W
P0_OUT_CTRL
1 = P0_x port output is powered by the 1 V rail
0 = P0_x port output is powered by the 3 V rail
bit 0 controls the power of P0[0],
bit 7 controls the power of P0[7]
(Note 4)
0x0
In Buck mode the output must be powered by the 3 V rail. In Boost mode the outputs can be powered by the 1 V rail or by the 3 V rail. In
Boost mode the 3 V rail can only supply a limited current, e.g. for switching a high-impedance input of an external device. See table 'Digital
input/output characteristics'.
Note 4:
In Buck mode the output must be powered by the 3 V rail. In Boost mode the outputs can be powered by the 1 V rail or by the 3 V rail. In
Boost mode the 3 V rail can only supply a limited current, e.g. for switching a high-impedance input of an external device. See table 'Digital
input/output characteristics'.
Table 223: P2_PADPWR_CTRL_REG (0x50003072)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0x0
9:0
R/W
P2_OUT_CTRL
1 = P2_x port output is powered by the 1 V rail
0 = P2_x port output is powered by the 3 V rail
bit 0 controls the power of P2[0],
bit 9 controls the power of P2[9],
(Note 5)
0x0
Note 5:
In Buck mode the output must be powered by the 3 V rail. In Boost mode the outputs can be powered by the 1 V rail or by the 3 V rail. In
Boost mode the 3 V rail can only supply a limited current, e.g. for switching a high-impedance input of an external device. See table 'Digital
Datasheet
CFR0011-120-01
Revision 3.4
131 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
input/output characteristics'.
Table 224: P3_PADPWR_CTRL_REG (0x50003074)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0
7:0
R/W
P3_OUT_CTRL
1 = P3_x port output is powered by the 1 V rail
0 = P3_x port output is powered by the 3 V rail
bit 0 controls the power of P3[0],
bit 7 controls the power of P3[7],
(Note 6)
0
Note 6:
In Buck mode the output must be powered by the 3 V rail. In Boost mode the outputs can be powered by the 1 V rail or by the 3 V rail. In
Boost mode the 3 V rail can only supply a limited current, e.g. for switching a high-impedance input of an external device. See table 'Digital
input/output characteristics'.
Table 225: P3_DATA_REG (0x50003080)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0
7:0
R/W
P3_DATA
Set P3 output register when written; Returns the value of P3
port when read
0
Table 226: P3_SET_DATA_REG (0x50003082)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0
7:0
R0/W
P3_SET
Writing a 1 to P3[y] sets P3[y] to 1. Writing 0 is discarded;
Reading returns 0
0
Table 227: P3_RESET_DATA_REG (0x50003084)
Bit
Mode
Symbol
Description
Reset
15:8
-
-
Reserved
0
7:0
R0/W
P3_RESET
Writing a 1 to P0[y] sets P0[y] to 0. Writing 0 is discarded;
Reading returns 0
0
Table 228: P30_MODE_REG (0x50003086)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 229: P31_MODE_REG (0x50003088)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
Datasheet
CFR0011-120-01
Revision 3.4
132 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 229: P31_MODE_REG (0x50003088)
Bit
Mode
Symbol
Description
Reset
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 230: P32_MODE_REG (0x5000308A)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 231: P33_MODE_REG (0x5000308C)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 232: P34_MODE_REG (0x5000308E)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 233: P35_MODE_REG (0x50003090)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
Datasheet
CFR0011-120-01
Revision 3.4
133 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 233: P35_MODE_REG (0x50003090)
Bit
Mode
Symbol
Description
Reset
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 234: P36_MODE_REG (0x50003092)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 235: P37_MODE_REG (0x50003094)
Bit
Mode
Symbol
Description
Reset
15:10
-
-
Reserved
0
9:8
R/W
PUPD
00 = Input, no resistors selected
01 = Input, pull-up selected
10 = Input, Pull-down selected
11 = Output, no resistors selected
In ADC mode, these bits are don't care
2
7:5
-
-
Reserved
0
4:0
R/W
PID
See P0x_MODE_REG[PID]
0
Table 236: WATCHDOG_REG (0x50003100)
Bit
Mode
Symbol
Description
Reset
15:9
R0/W
WDOG_WEN
0000.000 = Write enable for Watchdog timer
else Write disable. This filter prevents unintentional presetting the watchdog with a SW run-away.
0x0
8
R/W
WDOG_VAL_NEG
0 = Watchdog timer value is positive.
1 = Watchdog timer value is negative.
0x0
7:0
R/W
WDOG_VAL
Write: Watchdog timer reload value. Note that all bits 15-9
must be 0 to reload this register.
Read: Actual Watchdog timer value. Decremented by 1
every 10.24 msec. Bit 8 indicates a negative counter value.
2, 1, 0, 1FF16, 1FE16 etc. An NMI or WDOG (SYS) reset is
generated under the following conditions:
If WATCHDOG_CTRL_REG[NMI_RST] = 0 then
If WDOG_VAL = 0 -> NMI (Non Maskable Interrupt)
if WDOG_VAL = 1F016 -> WDOG reset -> reload FF16
If WATCHDOG_CTRL_REG[NMI_RST] = 1 then
if WDOG_VAL <= 0 -> WDOG reset -> reload FF16
0xFF
Datasheet
CFR0011-120-01
Revision 3.4
134 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 237: WATCHDOG_CTRL_REG (0x50003102)
Bit
Mode
Symbol
Description
Reset
15:2
-
-
Reserved
0x0
1
-
-
Reserved
0x0
0
R/W
NMI_RST
0 = Watchdog timer generates NMI at value 0, and WDOG
(SYS) reset at <=-16. Timer can be frozen /resumed using
SET_FREEZE_REG[FRZ_WDOG]/
RESET_FREEZE_REG[FRZ_WDOG].
0x0
1 = Watchdog timer generates a WDOG (SYS) reset at value
0 and can not be frozen by Software.
Note that this bit can only be set to 1 by SW and only be
reset with a WDOG (SYS) reset or SW reset.
The watchdog is always frozen when the Cortex-M0 is halted
in DEBUG State.
Table 238: CHIP_ID1_REG (0x50003200)
Bit
Mode
Symbol
Description
Reset
7:0
R
CHIP_ID1
First character of device type "580" in ASCII.
0x35
Table 239: CHIP_ID2_REG (0x50003201)
Bit
Mode
Symbol
Description
Reset
7:0
R
CHIP_ID2
Second character of device type "580" in ASCII.
0x38
Table 240: CHIP_ID3_REG (0x50003202)
Bit
Mode
Symbol
Description
Reset
7:0
R
CHIP_ID3
Third character of device type "580" in ASCII.
0x30
Table 241: CHIP_SWC_REG (0x50003203)
Bit
Mode
Symbol
Description
Reset
7:4
-
-
Reserved
0x0
3:0
R
CHIP_SWC
SoftWare Compatibility code.
Integer (default = 0) which is incremented if a silicon change
has impact on the CPU Firmware.
Can be used by software developers to write silicon revision
dependent code.
0x0
Table 242: CHIP_REVISION_REG (0x50003204)
Bit
Mode
Symbol
Description
Reset
7:0
R
REVISION_ID
Chip version, corresponds with type number in ASCII.
0x41 = 'A', 0x42 = 'B'
0x41
Table 243: SET_FREEZE_REG (0x50003300)
Bit
Mode
Symbol
Description
Reset
15:4
-
-
Reserved
0x0
Datasheet
CFR0011-120-01
Revision 3.4
135 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 243: SET_FREEZE_REG (0x50003300)
Bit
Mode
Symbol
Description
Reset
3
R/W
FRZ_WDOG
If '1', the watchdog timer is frozen, '0' is discarded.
WATCHDOG_CTRL_REG[NMI_RST] must be '0' to allow
the freeze function.
0x0
2
R/W
FRZ_BLETIM
If '1', the BLE master clock is frozen, '0' is discarded.
0x0
1
R/W
FRZ_SWTIM
If '1', the SW Timer (TIMER0) is frozen, '0' is discarded.
0x0
0
R/W
FRZ_WKUPTIM
If '1', the Wake Up Timer is frozen, '0' is discarded.
0x0
Table 244: RESET_FREEZE_REG (0x50003302)
Bit
Mode
Symbol
Description
Reset
15:4
-
-
Reserved
0x0
3
R/W
FRZ_WDOG
If '1', the watchdog timer continues, '0' is discarded.
0x0
2
R/W
FRZ_BLETIM
If '1', the the BLE master clock continues, '0' is discarded.
0x0
1
R/W
FRZ_SWTIM
If '1', the SW Timer (TIMER0) continues, '0' is discarded.
0x0
0
R/W
FRZ_WKUPTIM
If '1', the Wake Up Timer continues, '0' is discarded.
0x0
Table 245: DEBUG_REG (0x50003304)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
DEBUGS_FREEZE_
EN
Default '1', freezing of the on-chip timers is enabled when the
Cortex-M0 is halted in DEBUG State.
If '0', freezing of the on-chip timers is depending on
FREEZE_REG when the Cortex-M0 is halted in DEBUG
State except the watchdog timer. The watchdog timer is
always frozen when the Cortex-M0 is halted in DEBUG
State.
0x1
Table 246: GP_STATUS_REG (0x50003306)
Bit
Mode
Symbol
Description
Reset
15:1
-
-
Reserved
0x0
0
R/W
CAL_PHASE
If '1', it designates that the chip is in Calibration Phase i.e.
the OTP has been initially programmed but no Calibration
has occured.
0x0
Table 247: GP_CONTROL_REG (0x50003308)
Bit
Mode
Symbol
Description
Reset
15:6
-
-
Reserved
0
Datasheet
CFR0011-120-01
Revision 3.4
136 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 247: GP_CONTROL_REG (0x50003308)
Bit
Mode
Symbol
Description
Reset
5:1
R/W
EM_MAP
Select the mapping of the Exchange memory pages.
0: EM size 0 kB, SysRAM size 42 kB
1: EM size 2 kB, SysRAM size 48 kB
2: EM size 3 kB, SysRAM size 47 kB
3: EM size 4 kB, SysRAM size 46 kB
4: EM size 5 kB, SysRAM size 45 kB
5: EM size 6 kB, SysRAM size 44 kB
6: EM size 7 kB, SysRAM size 43 kB
7: EM size 8 kB, SysRAM size 42 kB
8: Reserved
9: EM size 4 kB, SysRAM size 40 kB
10: EM size 5 kB, SysRAM size 40 kB
11: EM size 6 kB, SysRAM size 40 kB
12: EM size 7 kB, SysRAM size 40 kB
13: EM size 8 kB, SysRAM size 40 kB
14: EM size 9 kB, SysRAM size 40 kB
15: EM size 10 kB, SysRAM size 40 kB
16: Reserved
17: EM size 6 kB, SysRAM size 38 kB
18: EM size 7 kB, SysRAM size 38 kB
19: EM size 8 kB, SysRAM size 38 kB
20: EM size 9 kB, SysRAM size 38 kB
21: EM size 10 kB, SysRAM size 38 kB
22: EM size 11 kB, SysRAM size 38 kB
23: EM size 12 kB, SysRAM size 38 kB
other: Reserved.
0x1
0
R/W
BLE_WAKEUP_REQ
If '1', the BLE wakes up. Must be kept high at least for 1 low
power clock period.
If the BLE is in deep sleep state, then by setting this bit it will
cause the wakeup LP IRQ to be asserted with a delay of 3 to
4 low power cycles.
0x0
Table 248: TIMER0_CTRL_REG (0x50003400)
Bit
Mode
Symbol
Description
Reset
15:4
-
-
Reserved
0x0
3
R/W
PWM_MODE
0 = PWM signals are '1' during high time.
1 = PWM signals send out the (fast) clock divided by 2 during high time. So it will be in the range of 1 to 8 MHz.
0x0
2
R/W
TIM0_CLK_DIV
1 = Timer0 uses selected clock frequency as is.
0 = Timer0 uses selected clock frequency divided by 10.
Note that this applies only to the ON-counter.
0x0
1
R/W
TIM0_CLK_SEL
1 = Timer0 uses 16, 8, 4 or 2 MHz (fast) clock frequency.
0 = Timer0 uses 32 kHz (slow) clock frequency.
0x0
0
R/W
TIM0_CTRL
0 = Timer0 is off and in reset state.
1 = Timer0 is running.
0x0
Table 249: TIMER0_ON_REG (0x50003402)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
TIM0_ON
Timer0 On reload value:
If read the actual counter value ON_CNTer is returned
0x0
Datasheet
CFR0011-120-01
Revision 3.4
137 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 250: TIMER0_RELOAD_M_REG (0x50003404)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
TIM0_M
Timer0 'high' reload valueIf read the actual counter value
T0_CNTer is returned
0x0
Table 251: TIMER0_RELOAD_N_REG (0x50003406)
Bit
Mode
Symbol
Description
Reset
15:0
R0/W
TIM0_N
Timer0 'low' reload value:
If read the actual counter value T0_CNTer is returned
0x0
Table 252: PWM2_DUTY_CYCLE (0x50003408)
Bit
Mode
Symbol
Description
Reset
13:0
R/W
DUTY_CYCLE
duty cycle for PWM
0x0
Table 253: PWM3_DUTY_CYCLE (0x5000340A)
Bit
Mode
Symbol
Description
Reset
13:0
R/W
DUTY_CYCLE
duty cycle for PWM
0x0
Table 254: PWM4_DUTY_CYCLE (0x5000340C)
Bit
Mode
Symbol
Description
Reset
13:0
R/W
DUTY_CYCLE
duty cycle for PWM
0x0
Table 255: TRIPLE_PWM_FREQUENCY (0x5000340E)
Bit
Mode
Symbol
Description
Reset
13:0
R/W
FREQ
Freq for PWM 2 3 4
0x0
Table 256: TRIPLE_PWM_CTRL_REG (0x50003410)
Bit
Mode
Symbol
Description
Reset
2
R/W
HW_PAUSE_EN
'1' = HW can pause PWM 2,3,4
0x1
1
R/W
SW_PAUSE_EN
'1' = PWM 2 3 4 is paused
0x0
0
R/W
TRIPLE_PWM_ENA
BLE
'1' = PWM 2 3 4 is enabled
0x0
Datasheet
CFR0011-120-01
Revision 3.4
138 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
6
FINAL
Specifications
All MIN/MAX specification limits are guaranteed by design, production testing and/or statistical characterization. Typical values are based on characterization results at default measurement conditions and are informative only.
Default measurement conditions (unless otherwise specified): VBAT(VBAT3V) = 3.0 V (buck mode), VBAT(VBAT1V)
= 1.2 V (boost mode), TA = 25 C. All radio measurements are performed with standard RF measurement equipment
providing a source/load impedance of 50 .
The specifications in the following tables are valid for the reference circuits shown in Figure 11 (Boost mode) and
Figure 12 (Buck mode).
9%$79
933
73
9%$7
9GFGF
6:&/. 73
%7
9$$$
/
X+
&
6:',2 73
&
&
'
'
(
(
(
'
&
%
(
(
9%$7B5)
9%$79
$
933
&
$
9'&'&B5)
3B
6:B&/.
'
%
6:',2
%
&
X)
&
X)
X)
9GFGF
3B
9'&'&
9%$79
&
X)
9%$7
$17
)
3B
&
X)
3B
3B
5),2S
3B
5),2P
8
3B
3B
$
$
'$
3B
;7$/0S
3B
;7$/0P
%
$
<
0+]
3B
3B
;7$/.S
)
<
N+]
*1'
)
%
*1'
*1'
&
*1'
$
'
)
*1'
;7$/.P
*1'
567
'
(
)
73
*1'
9%$7
)
73
6:,7&+
9%$7
Figure 11: Alkaline Battery Cell Powered System Diagram (Boost Mode)
Datasheet
CFR0011-120-01
Revision 3.4
139 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
9%$7
73
*1'
73
933
73
9%$7
FINAL
9GFGF
9%$7
9GFGF
/
6:&/. 73
'
'
(
(
(
'
&
%
9%$7B5)
)
6:,7&+
(
9%$79
$
933
&
$
9'&'&B5)
9'&'&
9%$79
)
)
3B
3B
3B
5),2S
3B
5),2P
8
3B
3B
%7
9&RLQ
&
X)
'$
3B
;7$/0S
3B
;7$/0P
$
$
%
<
0+]
$
3B
3B
;7$/.S
)
)
<
N +]
*1'
237,21$/
%
*1'
*1'
&
*1'
$
'
)
*1'
;7$/.P
*1'
567
'
(
$17
9%$7
&
3B
&
X)
&
3B
6:B&/.
'
%
6:',2
%
X+
&
X)
(
&
X)
6:',2 73
Figure 12: Lithium Coin Cell Powered System Diagram (Buck Mode)
Datasheet
CFR0011-120-01
Revision 3.4
140 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 257: Absolute Maximum Ratings
Parameter
Description
VPIN(LIM)(defaul limiting voltage on a pin
t)
TSTG
storage temperature
tR(SUP)
supply rise time
Conditions
Min
Voltage between pin and
GND
(Note 7)
Max
Unit
-0.1
min{3.6,
VBAT_RF
+0.2}
V
-50
150
°C
100
ms
Power supply rise time
Typ
VBAT(LIM)(VBAT limiting battery supply
voltage
1V)
Supply voltage on
VBAT1V in a boost converter application
(VBAT3V is second output of boost-converter in
this case)
(Note 7)
-0.1
3.6
V
VBAT(LIM)(VBAT limiting battery supply
voltage
3V)
Supply voltage on
VBAT3V and VBAT_RF
in a buck-converter
application, pin VBAT1V
is connected to ground
(Note 7)
-0.1
3.6
V
VPIN(LIM)(1V2)
limiting voltage on a pin
XTAL32Km, XTAL16Mp,
XTAL16Mm
(Note 7)
-0.2
min(1.2,V
BAT_RF+
0.2)
V
VPIN(LIM)(VDC
DC_RF)
limiting voltage on the
VDCDC_RF pin
Supply voltage on
VDCDC_RF
(Note 7)
-0.2
min(3.3,V
BAT_RF+
0.2)
V
VPIN(LIM)(XTAL
32Kp)
limiting voltage on a pin
XTAL32Kp
-0.2
min(1.5,V
BAT_RF+
0.2)
V
VESD(HBM)(WL
CSP34)
electrostatic discharge
voltage (Human Body
Model)
2000
V
VESD(HBM)(QF
N40)
electrostatic discharge
voltage (Human Body
Model)
4000
V
VESD(HBM)(QF
N48)
electrostatic discharge
voltage (Human Body
Model)
4000
V
VESD(MM)(WLC
SP34)
electrostatic discharge
voltage (Machine Model)
200
V
VESD(MM)(QFN
40)
electrostatic discharge
voltage (Machine Model)
200
V
VESD(MM)(QFN
48)
electrostatic discharge
voltage (Machine Model)
200
V
VESD(CDM)(WL
CSP34)
electrostatic discharge
voltage (Charged Device
Model)
500
V
VESD(CDM)(QF
N40)
electrostatic discharge
voltage (Charged Device
Model)
1000
V
VESD(CDM)(QF
N48)
electrostatic discharge
voltage (Charged Device
Model)
1000
V
Datasheet
CFR0011-120-01
Revision 3.4
141 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
Note 7:
FINAL
The device should not be exposed for prolonged periods of time to voltages between the Recommended Operating Conditions and the
Absolute Maximum Ratings range.
Table 258: Recommended Operating Conditions
Parameter
Description
Conditions
Min
Typ
Max
Unit
VPP
programming voltage
Supply voltage on pin
VPP during OTP programming; TJ  50 C
6.6
6.7
6.8
V
VBAT(VBAT1V)
battery supply voltage
Supply voltage on
VBAT1V in a boost converter application
(VBAT3V is second output of boost-converter in
this case)
0.9
3.3
V
VBAT(VBAT3V)
battery supply voltage
Supply voltage on
VBAT3V and VBAT_RF
in a buck-converter
application, pin VBAT1V
is connected to ground
3.3
V
VPIN(default)
voltage on a pin
Voltage between pin and
GND
0
min(3.3,V
BAT_RF+
0.2)
V
VPIN(1V2)
voltage on a pin
XTAL32Km, XTAL16Mp,
XTAL16Mm
0
1.2
V
VPIN(VDCDC_
RF)
voltage on a pin
Supply voltage on
VDCDC_RF
0
3.3
V
TA
ambient temperature
-40
85
°C
Note 8:
2.35
(Note 8)
Cold boot should not be performed if voltage is less than 2.5 V because of possible corruption during OTP data mirroring. Trim values programmed in the OTP as well as the application image, should be copied into RAM while VBAT3V >= 2.5 V.
Table 259: DC Characteristics
Parameter
Description
Conditions
IBAT(DP_SLP)_
BOOST_1kB
battery supply current
Boost configuration in
deep-sleep with 1 kB
retention RAM active,
running from RC32K
oscillator at lowest frequency
0.48
A
IBAT(DP_SLP)_
BOOST_2kB
battery supply current
Boost configuration in
deep-sleep with 2 kB
retention RAM active,
running from XTAL32K
oscillator
0.55
A
IBAT(DP_SLP)_
BOOST_8kB
battery supply current
Typical boost-application in deep-sleep with 8
kB retention RAM active,
running from XTAL32K
oscillator
0.7
IBAT(EXT_SLP)
_BOOST_43K
B
battery supply current
Typical boost-application in extended-sleep
mode with 42 kB (SysRAM) and 1 kB
(RetRAM) retained
1.37
Datasheet
CFR0011-120-01
Revision 3.4
142 of 155
Min
Typ
Max
2
Unit
A
A
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 259: DC Characteristics
Parameter
Description
Conditions
Min
Typ
Max
Unit
3
A
IBAT(EXT_SLP) battery supply current
_BOOST_50kB
Typical boost-application in extended-sleep
mode with 42 kB (SysRAM) and 8 kB
(RetRAM) retained
1.5
IBAT(DP_SLP)_
BUCK_1kB
battery supply current
Buck configuration in
deep-sleep with 1 kB
retention RAM active,
running from RC32K
oscillator at lowest frequency
0.4
A
IBAT(DP_SLP)_
BUCK_2kB
battery supply current
Buck configuration in
deep-sleep with 2 kB
retention RAM active,
running from XTAL32K
oscillator
0.45
A
IBAT(DP_SLP)_
BUCK_8kB
battery supply current
Typical buck-application
in deep-sleep with 8 kB
retention RAM active,
running from XTAL32K
oscillator
0.6
IBAT(EXT_SLP)
_BUCK_43KB
battery supply current
Typical buck-application
in extended-sleep mode
with 42 kB (SysRAM)
and 1 kB (RetRAM)
retained
1.2
IBAT(EXT_SLP)
_BUCK_50kB
battery supply current
Typical buck-application
in extended-sleep mode
with 42 kB (SysRAM)
and 8 kB (RetRAM)
retained
1.4
3
A
IBAT(ACT_RX)_ battery supply current
BOOST
Typical application with
boost converter and
receiver active
13.4
16
mA
IBAT(ACT_TX)_
BOOST
battery supply current
Typical application with
boost converter and
transmitter active
12.4
15
mA
IBAT(ACT_RX)_ battery supply current
BUCK
Typical application with
buck converter and
receiver active
5.1
6
mA
IBAT(ACT_TX)_
BUCK
Typical application with
buck converter and
transmitter active
4.8
6
mA
Typ
Max
Unit
battery supply current
A
2
A
Table 260: Timing Characteristics
Parameter
Description
Conditions
tSTA(BOOST)
startup time
Boost-mode; time from
deep-sleep to software
start.
Typical application, running from retention RAM
on 16 MHz RC oscillator
Datasheet
CFR0011-120-01
Revision 3.4
143 of 155
Min
1.2
(Note 9)
ms
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 260: Timing Characteristics
Parameter
Description
Conditions
tSTA(BUCK)
startup time
Buck-mode; time from
deep-sleep to software
start.
Typical application, running from retention RAM
on 16 MHz RC oscillator
Note 9:
Min
Typ
Max
1
(Note 9)
Unit
ms
Worst-case value under Normal Operating Conditions.
Table 261: 16 MHz Crystal Oscillator: Recommended Operating Conditions
Parameter
Description
fXTAL(16M)
crystal oscillator frequency
ESR(16M)
equivalent series resistance
CL(16M)
load capacitance
Conditions
Min
Typ
Max
16
Unit
MHz
100

pF
No external capacitors
are required
10
12
C0(16M)
shunt capacitance
5
pF
fXTAL(16M)
crystal frequency tolerance
After optional trimming;
including aging and temperature drift
(Note 10)
-20
20
ppm
fXTAL(16M)UNT
crystal frequency tolerance
Untrimmed; including
aging and temperature
drift
(Note 11)
-40
40
ppm
PDRV(MAX)(16M maximum drive power
)
(Note 12)
100
VCLK(EXT)(16M) external clock voltage
Only in case of an external reference clock on
XTAL16Mp (XTAL16Mm
floating or connected to
mid-level 0.6 V)
N(EXTERNAL)16M
fC = 50 kHz
in case of an external
reference clock
phase noise
1
W
1.2
V
-130
dBc/
Hz
Note 10: Using the internal varicaps a wide range of crystals can be trimmed to the required tolerance.
Note 11: Maximum allowed frequency tolerance for compensation by the internal varicap trimming mechanism.
Note 12: Select a crystal which can handle a drive-level equal or more than this specification
Table 262: 16 MHz Crystal Oscillator: Timing Characteristics
Parameter
Description
tSTA(XTAL)(16M)
crystal oscillator startup
time
Datasheet
CFR0011-120-01
Conditions
Revision 3.4
144 of 155
Min
Typ
Max
Unit
0.5
2
3
ms
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 263: 32 kHz Crystal Oscillator: Recommended Operating Conditions
Parameter
Description
Conditions
Min
Typ
Max
Unit
VCLK(EXT)(32K)
external clock voltage
peak-peak voltage of
external clock at
XTAL32Kp, pin
XTAL32Km floating.
note: XTAL32Kp is internally AC coupled
0.1
0.2
1.5
V
fXTAL(32k)
crystal oscillator frequency
frequency range for an
external clock
(for a crystal, use either
32.000 kHz or 32.768
kHz)
10
32.768
100
kHz
ESR(32k)
equivalent series resistance
100
k
CL(32k)
load capacitance
7
9
pF
C0(32k)
shunt capacitance
1
2
pF
fXTAL(32k)
crystal frequency tolerance (including aging)
Timing accuracy is dominated by crystal accuracy. A much smaller
value is preferred
250
ppm
PDRV(MAX)(32k)
maximum drive power
(Note 13)
no external capacitors
are required for a 6 pF or
7 pF crystal
6
-250
W
0.1
Note 13: Select a crystal that can handle a drive-level of at least this specification.
Table 264: 32 kHz Crystal Oscillator: Timing Characteristics
Parameter
Description
Conditions
tSTA(XTAL)(32k)
crystal oscillator startup
time
Typical application, time
until 1000 clocks are
detected
(Note 14)
Min
Typ
Max
0.4
Unit
s
Note 14: This parameter is very much dependent on crystal parameters
Table 265: DC-DC Converter: Recommended Operating Conditions
Parameter
Description
Conditions
Min
Typ
Max
Unit
L
effective inductance
1.5
2.2
3
H
COUT(VDCDC)
effective load capacitance
VDCDC and VDDCRF
combined
(Note 15)
0.5
1
10
F
COUT(VBAT3V)
effective load capacitance
VBATRF and VBAT3V
combined are the second output of the boostconverter
(Note 15)
0.5
1
10
F
Min
Typ
Max
Unit
Note 15: A low value will result in lowest power consumption, keep this value at 1 uF or 2 uF.
Table 266: DC-DC Converter: DC Characteristics
Parameter
Description
Conditions
VO(BUCK)
output voltage
default settings
Datasheet
CFR0011-120-01
Revision 3.4
145 of 155
1.41
V
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 266: DC-DC Converter: DC Characteristics
Parameter
Description
Conditions
default settings, VDCDC
Min
Typ
Max
Unit
VO(BOOST)
output voltage
1.41
V
CONV_MAX(BU
CK)
maximum conversion
efficiency
86
%
CONV_MAX(BO
OST)
maximum conversion
efficiency
80
%
VO/
VI(BUCK)
line regulation
2.35 V  VBAT3V  3.3 V
-2
0.7
2
%/V
VO/
VI(BOOST)
line regulation
0.9 V  VBAT1V  1.2 V
(Note 16)
-2
1
4
%/V
VO/IL(BUCK) load regulation
VBAT3V = 2.5 V
-0.2
-0.02
0.2
%/mA
VO/
IL(BOOST)
load regulation
VBAT1V = 1.2 V
-0.2
-0.07
0.2
%/mA
VRPL(BUCK)
ripple voltage
buck mode; RMS ripple
voltage
5
mV
VRPL(BOOST)
ripple voltage
VBAT1V  1.2 V, boost
mode; RMS ripple voltage
(Note 16)
8
mV
Note 16: When VBAT1V > VDCDC_nominal, VDCDC will follow VBAT1V.
Table 267: Digital Input/Output: DC Characteristics
Parameter
Description
Conditions
Min
Typ
Max
VIH
HIGH level input voltage
VIL
LOW level input voltage
VIH(RST)
HIGH level input voltage
RST pin
VIL(RST)
LOW level input voltage
RST pin
VOH(VBAT1V)
HIGH level output voltage
Iout = -250 A, VBAT3V
= 2.35 V, VBAT1V = 0.9
V
0.72
V
VOH(VBAT3V)
HIGH level output voltage
Iout = -4.8 mA, VBAT3V
= 2.35 V, VBAT1V = 0 V
(Note 17)
1.88
V
VOL(VBAT1V)
LOW level output voltage Iout = 250 A, VBAT3V =
2.35 V, VBAT1V = 0.9 V
0.18
V
VOL(VBAT3V)
LOW level output voltage Iout = 4.8 mA, VBAT3V =
2.35 V, VBAT1V = 0 V
(Note 18)
0.47
V
IIH
HIGH level input current
Vin = VBAT3V = 2.5 V
-1
1
A
IIL
LOW level input current
Vin = VSS = 0 V
-1
1
A
IIH(PD)
HIGH level input current
Vin = VBAT3V = 2.5 V
50
150
A
IIL(PU)
LOW level input current
Vin = VSS = 0 V
-150
-50
A
IIH(RST)
HIGH level input current
RST pin, V(RST) = 1.2 V
25
75
A
0.84
Unit
V
0.36
0.84
V
V
0.36
V
Note 17: In Boost mode the output source current is limited to Iout = -250 uA.
Note 18: In Boost mode the output sink current is limited to Iout = 250 uA.
Datasheet
CFR0011-120-01
Revision 3.4
146 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 268: General Purpose ADC: Recommended Operating Conditions
Parameter
Description
NBIT(ADC)
number of bits (resolution)
Conditions
Min
Typ
Max
10
Unit
bit
Table 269: General Purpose ADC: DC Characteristics
Parameter
Description
Conditions
Min
Typ
Max
Unit
VI(ZS)
zero-scale input voltage
single-ended, calibrated
at zero input
-2.5
0
2.5
mV
VI(FS)
full-scale input voltage
single-ended, calibrated
at zero input
1150
1180
1250
mV
VI(FSN)
negative full-scale input
voltage
differential, calibrated at
zero input
-1180
mV
VI(FSP)
positive full-scale input
voltage
differential, calibrated at
zero input
1180
mV
INL
integral non-linearity
-2
2
LSB
DNL
differential non-linearity
-2
2
LSB
Table 270: General Purpose ADC: Timing Characteristics
Parameter
Description
Conditions
tCONV(ADC)
conversion time
Excluding initial settling
time of the LDO and the
3x-attenuation (if used):
Min
Typ
Max
Unit
0.25
0.4
s
Typ
Max
Unit
LDO settling time is 20
s (max), 3x-attenuation
settling time = 1 s (max)
Using internal ADC-clock
(~200 MHz)
Table 271: Radio: DC Characteristics
Parameter
Description
Conditions
Min
IBAT(RF)RX
battery supply current
receive mode; radio
receiver and synthesizer
active; DCDC converter
assumed ideal; TA = 25
°C
(Note 19)
3.7
4.3
mA
IBAT(RF)TX
battery supply current
transmit mode; radio
transmitter and synthesizer active; DCDC converter assumed ideal; TA
= 25 °C
(Note 19)
3.4
4
mA
Note 19: The DCDC-converter efficiency is assumed to be 100 % to enable benchmarking of the radio currents at battery supply domain (VBAT3V =
3 V).
Datasheet
CFR0011-120-01
Revision 3.4
147 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 272: Radio: AC Characteristics
Parameter
Description
Conditions
PSENS(CLEAN)
sensitivity level
DC-DC converter
enabled; Dirty Transmitter disabled; TA = 25 °C;
PER = 30.8 %
(Note 20)
-93
dBm
PSENS
sensitivity level
Normal Operating Conditions; DC-DC converter
enabled; TA = 25 °C;
PER = 30.8 %
(Note 20)
-92.5
dBm
PI(max)
input power level
DC-DC converter disabled; TA = 25 C; PER 
30.8 %
(Note 20)
10
PINT(IMD)
intermodulation distortion interferer power
level
worst case interferer
level @ f1, f2 with 2f1-f2 =
f0, |f1-f2| = n MHz and n =
3,4,5; PWANTED = -64
dBm @ f0; PER = 30.8
%; TA = 25 °C
(Note 22)
-35
CIR(0)
carrier to interferer ratio
n = 0; interferer @ f1 = f0
+ n*1 MHz; TA = 25 °C
(Note 23)
7
21
dB
CIR(1)
carrier to interferer ratio
n = ±1; interferer @ f1 =
f0 + n*1 MHz; TA = 25 °C
(Note 23)
-3
15
dB
CIR(P2)
carrier to interferer ratio
n = +2 (image frequency); interferer @ f1
= f0 + n*1 MHz; TA = 25
C
(Note 23)
-20
-9
dB
CIR(M2)
carrier to interferer ratio
n = -2; interferer @ f1 =
f0 + n*1 MHz; TA = 25 C
(Note 23)
-30
-17
dB
CIR(P3)
carrier to interferer ratio
n = +3 (image frequency
+ 1 MHz); interferer @ f1
= f0 + n*1 MHz; TA = 25
C
(Note 23)
-30
-15
dB
CIR(M3)
carrier to interferer ratio
n = -3; interferer @ f1 =
f0 + n*1 MHz; TA = 25 C
(Note 23)
-35
-27
dB
CIR(4)
carrier to interferer ratio
|n| >= 4 (any other BLE
channel); interferer @ f1
= f0 + n*1 MHz; TA = 25
°C
(Note 23)
-37
-27
dB
Datasheet
CFR0011-120-01
Revision 3.4
148 of 155
Min
Typ
Max
Unit
dBm
-31
dBm
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 272: Radio: AC Characteristics
Parameter
Description
Conditions
PBL(I)
blocker power level
30 MHz  fBL  2000
MHz; PWANTED = -67
dBm; TA = 25 °C
(Note 24)
-5
dBm
PBL(II)
blocker power level
2003 MHz  fBL  2399
MHz; PWANTED = -67
dBm; TA = 25 °C
(Note 24)
-15
dBm
PBL(III)
blocker power level
2484 MHz  fBL  2997
MHz; PWANTED = -67
dBm; TA = 25 C
(Note 24)
-15
dBm
PBL(IV)
blocker power level
3000 MHz  fBL  12.75
GHz; PWANTED = -67
dBm; TA = 25 C
(Note 24)
-5
dBm
PRSSI(min)
RSSI power level
absolute power level for
RXRSSI[7:0] = 0; TA =
25 °C
(Note 25)
-115
-112
PRSSI(max)
RSSI power level
upper limit of monotonous range; TA = 25 °C
-26
-19
LACC(RSSI)BO
OST
level accuracy
tolerance of 5 % to 95 %
confidence interval of
PRF: when RXRSSI[7:0]
= X, 50 < X < 175; burst
mode 1500 packets; TA
= 25 °C; DC-DC converter in BOOST mode
0
3
dB
LACC(RSSI)BU
CK
level accuracy
tolerance of 5 % to 95 %
confidence interval of
PRF: when RXRSSI[7:0]
= X, 50 < X < 175; burst
mode 1500 packets; TA
= 25 °C; DC-DC converter in BUCK mode
0
2
dB
LRES(RSSI)
level resolution
gradient of monotonous
range for RXRSSI[7:0] =
X, 50 < X < 175; burst
mode 1500 packets; TA
= 25C
0.474
0.485
dB/
LSB
ACP(2M)
adjacent channel power
level
fOFFSET = 2 MHz; TA =
25C
(Note 26)
-53
-50
dBm
ACP(2M)(EOC) adjacent channel power
level
fOFFSET = 2 MHz; -40C
 TA  +85C
(Note 26)
-53
-47
dBm
ACP(3M)
fOFFSET  3 MHz; TA =
25C
(Note 26)
-57
-55
dBm
Datasheet
CFR0011-120-01
adjacent channel power
level
Revision 3.4
149 of 155
Min
0.46
Typ
Max
-109
Unit
dBm
dBm
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Table 272: Radio: AC Characteristics
Parameter
Description
ACP(3M)(EOC) adjacent channel power
level
Conditions
Min
fOFFSET  3 MHz; -40C
 TA  +85C
(Note 26)
-2
Typ
Max
Unit
-57
-47
dBm
-1
0
dBm
PO
output power level
VDD = 3 V; maximum
gain; TA = 25 °C
PO(HD2)
output power level (second harmonic)
VDD = 3 V; maximum
gain; TA = 25 C
-54
-40
dBm
PO(HD3)
output power level (third
harmonic)
VDD = 3 V; maximum
gain; TA = 25 C
-56
-40
dBm
PO(HD4)
output power level
(fourth harmonic)
VDD = 3 V; maximum
gain; TA = 25 C
-70
-40
dBm
PO(HD5)
output power level (fifth
harmonic)
VDD = 3 V; maximum
gain; TA = 25 C
-70
-40
dBm
PO(NFM)
output power level in
'Near Field Mode'
VDD = 3 V; maximum
gain; TA = 25 °C
(Note 27)
-20
-15
dBm
-25
Note 20: Measured according to Bluetooth® Low Energy Test Specification RF-PHY.TS/4.0.1, section 6.4.1.
Note 21: Measured according to Bluetooth® Low Energy Test Specification RF-PHY.TS/4.0.1, section 6.4.2.
Note 22: Measured according to Bluetooth® Core Technical Specification document, version 4.2, volume 6, section 4.4. Published value is for n =
IXIT = 4 . IXIT = 5 gives the same results, IXIT = 3 gives results that are 5 dB lower.
Note 23: Measured according to Bluetooth® Core Technical Specification document, version 4.2, volume 6, section 4.2.
Note 24: Measured according to Bluetooth® Core Technical Specification document, version 4.2, volume 6, section 4.3. Due to limitations of the
measurement equipment, levels of -5 dBm should be interpreted as > -5 dBm.
Note 25: PRF = PRSSI(min) + LRES(RSSI) x RXRSSI[7:0] ± LACC(RSSI). Thanks to constant gain biasing of RF part in the receiver, the RSSI can
be used to estimate absolute power levels, rather than mere level changes. Even across the full temperature range the variation is limited.
Note 26: Measured according to Bluetooth® Low Energy Test Specification RF-PHY.TS/4.0.1, section 6.2.3.
Note 27: To activate the "Near Field Mode", program address 0x50002418 with the value 0x0030.
Table 273: Stable Low Frequency RCX Oscillator: Timing Characteristics
Parameter
Description
Conditions
Min
Typ
Max
Unit
fRC(RCX)
RCX oscillator frequency
default setting, buck
mode only
5
10
40
kHz
fRC(RCX)
RCX oscillator frequency drift
buck mode only
(Note 28)
500
ppm
TA/
t(RCX)100ms
ambient temperature
gradient
buck mode only; connection interval 100 ms
0.66
°C/s
TA/t(RCX)4s
ambient temperature
gradient
buck mode only; connection interval 4 s
0.33
°C/s
-500
Note 28: Maximum recommended connection interval (including slave latency) for the RCX usage is 2 s.
Datasheet
CFR0011-120-01
Revision 3.4
150 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
7
FINAL
Package Information
7.1 MOISTURE SENSITIVITY LEVEL (MSL)
The MSL is an indicator for the maximum allowable
time period (floor life time) in which a moisture sensitive plastic device, once removed from the dry bag, can
be exposed to an environment with a maximum temperature of 30 °C and a maximum relative humidity of
60 % RH. before the solder reflow process.
WLCSP packages are qualified for MSL 1.
QFN packages are qualified for MSL 3.
MSL Level
Floor Life Time
MSL 4
72 hours
MSL 3
168 hours
MSL 2A
4 weeks
MSL 2
1 year
MSL 1
Unlimited at 30 °C / 85 % RH
7.2 WLCSP HANDLING
Manual handling of WLCSP packages should be
reduced to the absolute minimum. In cases where it is
still necessary, a vacuum pick-up tool should be used.
In extreme cases plastic tweezers could be used, but
metal tweezers are not acceptable, since contact may
easily damage the silicon chip.
Removal will cause damage to the solder balls and
therefore a removed sample cannot be reused.
WLCSP is sensitive to visible and infrared light. Precautions should be taken to properly shield the chip in
the final product.
7.3 SOLDERING INFORMATION
Refer to the JEDEC standard J-STD-020 for relevant
soldering information.
This document can be downloaded from http://
www.jedec.org
Datasheet
CFR0011-120-01
Revision 3.4
151 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
7.4 PACKAGE OUTLINES
Figure 13: QFN48 Package Outline Drawing
Datasheet
CFR0011-120-01
Revision 3.4
152 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Figure 14: QFN40 Package Outline Drawing
Datasheet
CFR0011-120-01
Revision 3.4
153 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Figure 15: WLCSP34 Package Outline Drawing
Datasheet
CFR0011-120-01
Revision 3.4
154 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
DA14580
Bluetooth Low Energy 4.2 SoC
FINAL
Status Definitions
Version
Datasheet Status
Product Status
Definition
1.<n>
Target
Development
This datasheet contains the design specifications for product
development. Specifications may change in any manner without
notice.
2.<n>
Preliminary
Qualification
This datasheet contains the specifications and preliminary characterization data for products in pre-production. Specifications
may be changed at any time without notice in order to improve
the design.
3.<n>
Final
Production
This datasheet contains the final specifications for products in
volume production. The specifications may be changed at any
time in order to improve the design, manufacturing and supply.
Major specification changes are communicated via Customer
Product Notifications. Datasheet changes are communicated
via www.dialog-semiconductor.com.
4.<n>
Obsolete
Archived
This datasheet contains the specifications for discontinued
products. The information is provided for reference only.
Disclaimer
Information in this document is believed to be accurate and reliable. However, Dialog Semiconductor does not give any
representations or warranties, expressed or implied, as to the accuracy or completeness of such information. Dialog Semiconductor furthermore takes no responsibility whatsoever for the content in this document if provided by any information
source outside of Dialog Semiconductor.
Dialog Semiconductor reserves the right to change without notice the information published in this document, including
without limitation the specification and design of the related semiconductor products, software and applications.
Applications, software, and semiconductor products described in this document are for illustrative purposes only. Dialog
Semiconductor makes no representation or warranty that such applications, software and semiconductor products will be
suitable for the specified use without further testing or modification. Unless otherwise agreed in writing, such testing or
modification is the sole responsibility of the customer and Dialog Semiconductor excludes all liability in this respect.
Customer notes that nothing in this document may be construed as a license for customer to use the Dialog Semi-conductor products, software and applications referred to in this document. Such license must be separately sought by customer
with Dialog Semiconductor.
All use of Dialog Semiconductor products, software and applications referred to in this document are subject to Dialog
Semiconductor's Standard Terms and Conditions of Sale, available on the company website (www.dialog-semiconductor.com) unless otherwise stated.
Dialog and the Dialog logo are trademarks of Dialog Semiconductor plc or its subsidiaries. All other product or service
names are the property of their respective owners.
© 2014 Dialog Semiconductor. All rights reserved.
RoHS Compliance
Dialog Semiconductor's suppliers certify that its products are in compliance with the requirements of Directive 2011/65/EU
of the European Parliament on the restriction of the use of certain hazardous substances in electrical and electronic equipment. RoHS certificates from our suppliers are available on request.
Contacting Dialog Semiconductor
United Kingdom (Headquarters)
Dialog Semiconductor (UK) LTD
Phone: +44 1793 757700
North America
Dialog Semiconductor Inc.
Phone: +1 408 845 8500
Singapore
Dialog Semiconductor Singapore
Phone: +65 64 8499 29
China (Shenzhen)
Dialog Semiconductor China
Phone: +86 755 2981 3669
Germany
Dialog Semiconductor GmbH
Phone: +49 7021 805-0
Japan
Dialog Semiconductor K. K.
Phone: +81 3 5425 4567
Hong Kong
Dialog Semiconductor Hong Kong
Phone: +852 3769 5200
China (Shanghai)
Dialog Semiconductor China
Phone: +86 21 5424 9058
The Netherlands
Dialog Semiconductor B.V.
Phone: +31 73 640 8822
Taiwan
Dialog Semiconductor Taiwan
Phone: +886 281 786 222
Korea
Dialog Semiconductor Korea
Phone: +82 2 3469 8200
155
Email:
[email protected]
Web site:
www.dialog-semiconductor.com
Datasheet
CFR0011-120-01
Revision 3.4
155 of 155
09-Nov-2016
© 2014 Dialog Semiconductor
Similar pages