Shoulder HDF915CS6 The product shall be packed properly not to be damaged during transportation and storage Datasheet

规格书编号
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF915C SMD-6
MARKING 印 字:
HDF6907
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2006-5-11
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 8
SAW FILTER
HDF915C
S6
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 8
SAW FILTER
HDF915C
S6
1. Package Dimension
2. Marking:HDF6907
HD: Brand
F : Filter
6:SMD-6
907 : No.
3.Performance
3.1Application
Low-Loss SAW Filter of cordless system.
Center Frequency:915 MHz
3.2Maximum Rating
Operation Temperature Range
www.shoulder.cn
-40℃ to +85℃
Storage Temperature Range
-40℃to +85℃
DC. Permissive Voltage
0 V DC. max.
Maximum Input Power
5dBm
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 3 of 8
SAW FILTER
3.3Electronic Characteristics
Item
Center Frequency(fo)
Insertion Loss
902~928 MHz
1.)580~790 MHz
2.)790~860 MHz
3.)970~1040 MHz
4.)1040~1250 MHz
5.)1500~2000 MHz
Ripple deviation (902.5-928MHz)(dB)
Input/output Impedance(Nominal)
HDF915C
S6
Specification
915MHz
5.0 dB max
45 dB min
30 dB min
20 dB min
40 dB min
20 dB min
2.0max
50Ω
3.4 Frequency Characteristics
3.5 Test Circuit
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 8
SAW FILTER
HDF915C
S6
4. ENVIRONMENTAL CHARACTERISTICS
4-1 Temperature cycling
Subject the device to a low temperature of -40℃ for 30 minutes. Following by a
high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30
Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the
measurement. It shall meet the specifications in 3.3.
4-2 Resistance to solder heat
Submerge the device terminals into the solder bath at 260℃±5℃ for 10±1 sec.
Then release the device into the room conditions for 4 hours. It shall meet the specifications
in 3.3.
4-3 Solderability
Submerge the device terminals into the solder bath at 245℃±5℃ for 5s, More than
95% area of the soldering pad must be covered with new solder. It shall meet the
specifications in 3.3.
4-4 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the
filter shall fulfill the specifications in 3.3.
4-5 Vibration
Subject the device to the vibration for 2 hour each in x,y and z axes with the
amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 3.3.
5. REMARK
5.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of
the component. Please avoid static voltage.
5.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please
avoid ultrasonic cleaning
5.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
6. Packing
6.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 5 of 8
SAW FILTER
HDF915C
S6
6.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
6.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
(2) Label
Device Name
User Product Name
Quantity
Lot No.
(3) Leader part and vacant position specifications.
7. TAPE SPECIFICATIONS
7.1 Tensile Strength of Carrier Tape: 4.4N/mm width
7.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 8
SAW FILTER
HDF915C
S6
(2) speed: 300mm/min.
(3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.0
±
0.3
5.5
±
0.05
1.75
±
0.1
4.0
±
0.1
4.0
±
0.1
2.0
±0.05
Ø1.5
±0.1
Ø1.0
±
0.25
0.3
±
0.05
1.25
±
0.1
3.3±
0.1
3.3
±
0.1
[Figure 2]
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 8
SAW FILTER
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
HDF915C
E-mail:[email protected]
S6
Page 8 of 8
Similar pages