TI1 D24051QM96G4Q1 High-speed cmos logic Datasheet

CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
D Qualified for Automotive Applications
D Wide Analog Input Voltage Range:
D
D
D
D
D
+5 V Max
Low ON Resistance
− 70 W Typical (VCC − VEE = 4.5 V)
− 40 W Typical (VCC − VEE = 9 V)
D Operation Control Voltage: 4.5 V to 5.5 V
D Switch Voltage: 0 V to 10 V
D Direct LSTTL Input Logic Compatibility:
D
Low Crosstalk Between Switches
Fast Switching and Propagation Speeds
Break-Before-Make Switching
Wide Operating Temperature Range: −405C
to 1255C
description/ordering information
This device is a digitally controlled analog switch that
utilizes silicon-gate CMOS technology to achieve
operating speeds similar to LSTTL, with the low
power consumption of standard CMOS integrated
circuits.
VIL = 0.8 V Max, VIH = 2 V Min
CMOS Input Compatibility: II v 1 mA at VOL,
VOH
M PACKAGE
(TOP VIEW)
A4
A6
COM OUT/IN A
A7
A5
E
VEE
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
A2
A1
A0
A3
S0
S1
S2
This analog multiplexer/demultiplexer controls analog voltages that may vary across the voltage supply range
(i.e., VCC to VEE ). It is a bidirectional switch that allows any analog input to be used as an output and vice-versa.
The switch has low ON resistance and low OFF leakages. In addition, this device has an enable control that,
when high, disables all switches to their OFF state.
ORDERING INFORMATION{
PACKAGE‡
TA
−40°C to 125°C
SOIC − M
Reel of 2500
ORDERABLE
PART NUMBER§
CD74HCT4051QM96Q1
TOP-SIDE
MARKING
HCT4051Q
†
For the most current package and ordering information, see the Package Option Addendum at the
end of this document, or see the TI web site at http://www.ti.com.
‡ Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging.
§ The suffix 96 denotes tape and reel.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2008, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
FUNCTION TABLE
INPUTS
ON CHANNELS
ENABLE
S2
S1
L
L
L
L
A0
L
L
L
H
A1
L
L
H
L
A2
L
L
H
H
A3
L
H
L
L
A4
L
H
L
H
A5
L
H
H
L
A6
L
H
H
H
A7
H
X
X
X
None
S0
X = Don’t care
logic diagram (positive logic)
Channel In/Out
VCC
A6
A7
16
4
2
A5
5
A4
1
A3 A2 A1 A0
12 15 14 13
TG
TG
S0
11
Address Select
TG
S1
10
Logic
Level
Conversion
S2
TG
Binary
to
1 of 8
Decoder
With
Enable
9
3
TG
TG
TG
E
8
TG
8
GND
2
7
VCC
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
COM
OUT/IN
A
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range: VCC − VEE (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 10.5 V
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to +7 V
VEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to −7 V
Input clamp current, IIK (VI < −0.5 V or VI > VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < VEE − 0.5 V or VO > VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Switch current (VI > VEE − 0.5 V or VI < VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
VEE current, IEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20 mA
Package thermal impedance, θJA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature (during soldering):
At distance 1/16 ± 1/32 inch (1,59 ± 0,79 mm) from case for 10 s max . . . . . . . . . . . . . . . . . . . . . . . 300°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages referenced to GND unless otherwise specified.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
VCC
Supply voltage
MIN
MAX
UNIT
4.5
5.5
V
Supply voltage, VCC − VEE (see Figure 1)
2
10
V
VEE
Supply voltage (see Note 4 and Figure 2)
0
−6
V
VIH
High-level input voltage
2
VIL
Low-level input voltage
VI
Input control voltage
VIS
Analog switch I/O voltage
tt
Input transition (rise and fall) time
TA
Operating free-air temperature
VCC = 4.5 V
V
0.8
V
0
VCC
V
VEE
VCC
V
0
500
ns
−40
125
°C
NOTES: 3. All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4. In certain applications, the external load resistor current may include both VCC and signal-line components. To avoid drawing VCC
current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed
0.6 V (calculated from ron values shown in electrical characteristics table). No VCC current flows through RL if the switch current flows
into the COM OUT/IN A terminal.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
recommended operating area as a function of supply voltages
8
(VCC – GND) – V
(VCC – GND) – V
8
6
HCT
HC
4
2
6
HCT
HC
4
2
0
0
0
2
4
6
8
10
0
12
−2
(VCC – VEE) – V
−4
−6
−8
(VEE – GND) – V
Figure 2
Figure 1
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VEE
MIN
ron
VIS = VCC or VEE
IO = 1 mA,
VI = VIH or VIL,
See Figure 9
VIS = VCC to VEE
∆ron
Between any two channels
IIZ
For switch OFF:
When VIS = VCC, VOS = VEE;
When VIS = VEE, VOS = VCC
For switch ON:
All applicable combinations of VIS and VOS
voltage levels,
VI = VIH or VIL
IIL
ICC
∆ICC
VI = VCC or GND
IO = 0,
VI = VCC or GND
TYP
MAX
4.5 V
70
160
240
4.5 V
40
120
180
0V
4.5 V
90
180
270
−4.5 V
4.5 V
45
130
195
0V
4.5 V
10
−4.5 V
4.5 V
5
0V
6V
Ω
Ω
±0.2
±2
A
µA
−5 V
5V
±0.4
±4
5.5 V
±0.1
±1
When VIS = VEE,
VOS = VCC
0V
5.5 V
8
160
When VIS = VCC,
VOS = VEE
−4.5 V
5.5 V
16
320
360
490
µA
A
µA
4.5 V
to
5.5 V
HCT input loading
TYPE
INPUT
UNIT LOADS†
4051
All
0.5
Unit load is ∆ICC limit specified in the electrical
characteristics table, e.g., 360 µA max at 25°C.
POST OFFICE BOX 655303
UNIT
MAX
0V
100
NOTE 5: For dual-supply systems, theoretical worst case (VI = 2.4 V, VCC = 5.5 V) specification is 1.8 mA.
4
MIN
−4.5 V
Control input
Per input pin: 1 unit load,
See Note 5, VIN = VCC − 2.1 V
†
TA = −40°C
TO 125°C
TA = 25°C
VCC
• DALLAS, TEXAS 75265
µA
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figure 8)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
VEE
MIN
CL = 15 pF
tpd
IN
OUT
5V
S or E
OUT
CI
S or E
OUT
MAX
MIN
UNIT
MAX
4
0V
4.5 V
12
18
CL = 50 pF
−4.5 V
4.5 V
8
12
5V
0V
4.5 V
55
83
CL = 50 pF
−4.5 V
4.5 V
39
59
5V
ns
23
CL = 50 pF
CL = 15 pF
tdis
TYP
CL = 50 pF
CL = 15 pF
ten
TA = −40°C
TO 125°C
TA = 25°C
VCC
ns
19
CL = 50 pF
0V
4.5 V
45
68
CL = 50 pF
−4.5 V
4.5 V
32
48
10
10
Control
ns
pF
operating characteristics, VCC = 5 V, TA = 25°C, input tr, tf = 6 ns
PARAMETER
Cpd
TYP
Power dissipation capacitance (see Note 6)
52
UNIT
pF
NOTE 6: Cpd is used to determine the dynamic power consumption (PD), per package.
PD = (Cpd × VCC2 × fI) + Σ (CL + CS) VCC2 × fO
fO = output frequency
fI = input frequency
CL = output load capacitance
CS = switch capacitance
VCC = supply voltage
analog channel characteristics, TA = 25°C
PARAMETER
TEST CONDITIONS
CI
Switch input capacitance
CCOM
Common output capacitance
fmax
Minimum switch frequency
response at −3 dB
See Figure 3 and Figure 10 and
Notes 7 and 8
Sine wave distortion
Sine-wave
See Figure 5
E or address select (S0, S1, S2) to
switch feedthrough noise
See Figure 6 and Notes 8 and 9
Switch OFF signal feedthrough
See Figure 7 and Figure 11 and
Notes 8 and 9
VEE
VCC
TYP
UNIT
5
pF
25
pF
−2.25 V
2.25 V
145
−4.5 V
4.5 V
180
−2.25 V
2.25 V
0.035
−4.5 V
4.5 V
0.018
−2.25 V
2.25 V
TBE
−4.5 V
4.5 V
TBE
−2.25 V
2.25 V
−73
−4.5 V
4.5 V
−75
MHz
%
mV
dB
NOTES: 7. Adjust input voltage to obtain 0 dBm at VOS for fIN = 1 MHz.
8. VIS is centered at (VCC − VEE)/2.
9. Adjust input for 0 dBm.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
PARAMETER MEASUREMENT INFORMATION
VCC
VIS
R
SWITCH
ON
VOS1
0.1 mF
INPUT
R
fIS = 1-MHz Sine Wave
R = 50 W
C = 10 pF
VCC/2
VCC
VCC
R
VOS
SWITCH
ON
VIS
C
0.1 mF
50 Ω
dB
METER
10 pF
VOS2
SWITCH
OFF
VCC/2
dB
METER
C
R
VCC/2
VCC/2
Figure 4. Crosstalk Between Two Switches
Test Circuit
Figure 3. Frequency-Response Test Circuit
E
VCC
V P−P
VCC
V OS
Sine
Wave
VIS
SWITCH
ON
VOS
10 mF
10k Ω
50 pF
SWITCH
ALTERNATING
ON AND OFF
tr, tf ≤ 6 ns
fCONT = 1 MHz
50% DUTY
CYCLE
600 Ω
VIS
VI = VIH
VCC/2
DISTORTION
METER
V OS
600 Ω
50 pF
SCOPE
VCC/2
VCC/2
fIS = 1 kHz to 10 kHz
Figure 5. Sine-Wave Distortion Test Circuit
Figure 6. Control-to-Switch Feedthrough Noise
Test Circuit
fIS ≥ 1-MHz Sine Wave
R = 50 Ω
C = 10 pF
VCC
0.1 µF
SWITCH
V IS
VC = VIL
V OS
OFF
dB
R
R
VCC/2
VCC/2
C
METER
Figure 7. Switch OFF Signal Feedthrough Test Circuit
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
PARAMETER MEASUREMENT INFORMATION
VCC
Test
Point
From Output
Under Test
PARAMETER
S1
ten
RL = 1 kΩ
tdis
CL
(see Note A)
S2
S1
S2
tPZH
Open
Closed
tPZL
Closed
Open
tPHZ
Open
Closed
tPLZ
Closed
Open
Open
Open
tpd
VEE
LOAD CIRCUIT
VCC
Input
50% VCC
50% VCC
VEE
tPLH
In-Phase
Output
50%
10%
90%
tPHL
90%
1.3 V
1.3 V
0V
tPHL
90%
tr
Out-of-Phase
Output
3V
Output
Control
tPZL
VOH
50% VCC
10%
VOL
tf
50% VCC
10%
tf
50%
10%
90%
tr
VOLTAGE WAVEFORMS
PROPAGATION DELAY AND OUTPUT TRANSITION TIMES
50% VCC
tPZH
VOH
VOL
≈VCC
Output
Waveform 1
(see Note B)
tPLH
tPLZ
Output
Waveform 2
(see Note B)
10%
VOL
tPHZ
50% VCC
90%
VOH
≈0 V
VOLTAGE WAVEFORMS
OUTPUT ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and test-fixture capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following
characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns.
D. For clock inputs, fmax is measured with the input duty cycle at 50%.
E. The outputs are measured one at a time, with one input transition per measurement.
F. tPLZ and tPHZ are the same as tdis.
G. tPZL and tPZH are the same as ten.
H. tPLH and tPHL are the same as tpd.
Figure 8. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
CD74HCT4051-Q1
HIGH-SPEED CMOS LOGIC
ANALOG MULTIPLEXER/DEMULTIPLEXER
SCLS569B − JANUARY 2004 − REVISED APRIL 2008
TYPICAL CHARACTERISTICS
120
ON Resistance − Ω
100
80
VCC − VEE = 4.5 V
60
VCC − VEE = 6 V
40
VCC − VEE = 9 V
20
1
2
3
4
5
6
7
8
9
Input Signal Voltage − V
Figure 9. Typical ON Resistance vs Input Signal Voltage
0
0
VCC = 4.5 V
GND = −4.5 V
VEE = −4.5 V
RL = 50 Ω
Pin 12 to 3
−4
−20
−40
dB
VCC = 2.25 V
GND = −2.25 V
VEE = −2.25 V
RL = 50 Ω
Pin 12 to 3
−6
−60
VCC = 4.5 V
GND = −4.5 V
VEE = −4.5 V
RL = 50 Ω
Pin 12 to 3
−80
−8
−10
10K
VCC = 2.25 V
GND = −2.25 V
VEE = −2.25 V
RL = 50 Ω
Pin 12 to 3
dB
−2
100K
1M
10M
100M
−100
10K
100K
Frequency − Hz
10M
100M
Frequency − Hz
Figure 10. Channel ON Bandwidth
8
1M
POST OFFICE BOX 655303
Figure 11. Channel OFF Feedthrough
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
23-Mar-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
CD74HCT4051QM96Q1
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
D24051QM96G4Q1
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF CD74HCT4051-Q1 :
CD74HCT4051
• Catalog:
• Military: CD54HCT4051
NOTE: Qualified Version Definitions:
- TI's standard catalog product
• Catalog
• Military - QML certified for Military and Defense Applications
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages