Technology NTDM-HS-24-208 N1 redundant hot swap power system Datasheet

APPLIED POWER CONVERSION
Division of
TECHNOLOGY DYNAMICS INC.
NTDM-HS SERIES
1500W-6000W
N+1 REDUNDANT HOT SWAP POWER SYSTEMS
5.25” x 19” x 17.75”
APPLICATIONS
The NTDM-4HS Series of Hot Swap Rack
Power Supply systems offer (N+1) redundant
or high power paralleled outputs of 2 modules
per enclosure. This series is especially suitable
for critical telecom and wireless systems or
where bulk power is required. Modules may
be removed while system is active for ease
of replacement resulting in no down time.
STANDARD FEATURES
• MTBF > 150.000 Hours
• LED Indicators (Each Module):
Output Power Good; Input Power Good
• Tightly Regulated
• Equipped with Isolation
Diodes for Redundancy/Parallel Operation
• Circuit Breaker Input
• OV/OL/OT Protection Main Output
• Floating Connectors for Hot Swap Insertion
• Remote Sensing Post Isolation Diodes
• Sturdy Fold Down Handle
AVAILABLE OPTIONS
• Power Factor Correction
• Militarized Version: MIL-STD-810
• Low Voltage Battery Disconnect
(LVBD) for Battery Back-Up Operation
• Terminal Block Input
• 3 Phase Input
• 400 Hz Operation
• Circular Connector Type MS-3102
• Militarized Version: MIL-STD-461
SPECIFICATIONS
A
ELECTRICAL:
Input:
(1500W) Module 85-132 - 175-265VAC, 47-63 Hz
(2000-3000W) Module 220VAC 1Phase or 115/208 3Phase
Regulation: Line ± .3%
Load ± 2%
Ripple: 1% Peak to Peak, Not to Exceed 200mV
Efficiency: 80% Typical
Hold Up Time: 20ms Min.
In Rush Current: 60A max ½ Cycle/Module
Protections: OV,OL & OT
MECHANICAL & ENVIRONMENTAL
Operational Temperature: 0˚C to + 50˚C Standard
-40˚C to + 60˚C Optional
Storage Temperature: 0˚C to + 85˚C
Cooling: Internal DC Fan
Weight: Modules (15 lbs) Each, Rack (24.5 lbs)
Size: 5.25”(H) x 19” Std. Rack (W) x 17.75” (L)
AS 9100
Design Excellence since 1976!
Certificate No: US008267-1
MODEL SELECTION
1500 WATT MODULES
2000 WATT MODULES
Max. Volts/Amps
Per Module
System Model
2 Modules
3000 WATT MODULES
2500 WATT MODULES
Max. Volts/Amps
Per Module
System Model
2 Modules
Max. Volts/Amps
Per Module
12V@125A
NTDM-HS-12-250
15V@100A
NTDM-HS-15-200
24V@62A
NTDM-HS-24-124
24V@83A
NTDM-HS-24-166
24V@104A
NTDM-HS-24-208
24V@125A
NTDM-HS-24-250
28V@54A
NTDM-HS-28-108
28V@71A
NTDM-HS-28-142
28V@89A
NTDM-HS-28-178
28V@107A
NTDM-HS-28-208
48V@31A
NTDM-HS-48-62
48V@41A
NTDM-HS-48-82
48V@52A
NTDM-HS-48-102
48V@62A
NTDM-HS-48-124
110@14A
NTDM-HS-110-28
110V@18A
NTDM-HS-110-36
110V@22A
NTDM-HS-110-44
110V@27A
NTDM-HS-110-54
Max. Volts/Amps
Per Module
CONSULT FACTORY
CONSULT FACTORY
3000W PARALLEL/1500 REDUNDANT
System Model
2 Modules
4000W PARALLEL/2000 REDUNDANT
System Model
2 Modules
CONSULT FACTORY
6000W PARALLEL/3000 REDUNDANT
5000W PARALLEL/2500 REDUNDANT
Note: Model information assumes a fully populated rack (2 modules).
SFX.
Options Designations
-TBC
Terminal Block Covers
-MIL
Ruggedized/Militarized
-LVBD
Battery Back-Up
-PFC
Power Factor Correction
-3PH
3 Phase Input
-4HZ
400 Hz Operation
-EMI
Additional EMI Filtering
-MTR
Meter (Volt/Amp) on Each Module
Low Voltage Battery Disconnect
The LVBD module adds a new dimension to
battery backup power supplies. The power
supply simultaneously charges the battery and
powers the load. If the AC power fails, the
battery continues to support the load. However,
when the battery voltage drops below a predetermined level, the LVBD module disconnects
the battery from the load, thereby protecting the
battery from the damaging effects of complete
discharge.
MECHANICAL OUTLINE
J1 INPUT CONNECTOR
ITT CONNECTOR
P/N MS3102R24-10P
LOGIC CONNECTOR
DAM-15S
427.74mm/16.84"
133.10mm
5.24"
E1
J2
LOGIC
E2
94.84mm
4.847"
OUTPUT
31.24mm
1.23"
J1 INPUT
37.69mm
1.926"
87.63mm
3.45"
41.91mm
1.65"
217.42mm/8.56"
331.22mm/13.04"
REAR VIEW
NAMEPLATE
POSITIVE OUTPUT
1/4-20 STUD X 1.75 LG
NEGATIVE OUTPUT
1/4/-20 STUD X 1.75 LG
TOP VIEW
CIRCUIT
BREAKERS
AIR
CIRCUIT
BREAKER
MODULE #1
TECHNOLOGY
DYNAMICS INC.
100 SCHOOL ST. BERGENFIELD, NJ 07621 USA
AIR
AIR INLET
MODULE #2
TECHNOLOGY
DYNAMICS INC.
100 SCHOOL ST. BERGENFIELD, NJ 07621 USA
AIR FLOW
133.10mm
5.24"
CHASSIS SLIDE CENTER LINE
INPUT
GOOD
44.07mm
2.252"
OUTPUT
GOOD
INPUT
GOOD
ADJUSTMENTS
O.L.
ADJ
VOLT
ADJ
OUTPUT
GOOD
ADJUSTMENTS
O.L.
ADJ
O.V.
ADJ
VOLT
ADJ
O.V.
ADJ
482.60mm/19.00"
450.85mm/17.75"
FRONT VIEW
SIDE VIEW
ADJUSTMENTS
CHASSIS SLIDE(BOTH SIDES)
Rev. A
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
TECHNOLOGY DYNAMICS INC.
100 School Street, Bergenfield, NJ 07621
Phone: (201) 385-0500, Fax: (201) 385-0702
www.technologydynamicsinc.com
Similar pages