Micron MTFDDAT128MAM1J12AA C400 msata nand flash ssd Datasheet

C400 mSATA NAND Flash SSD
Features
C400 mSATA NAND Flash SSD
MTFDDAT128MAM, MTFDDAT256MAM
Features
•
•
•
•
•
•
•
•
•
•
•
• Reliability
– MTTF: 1.2 million device hours3
– Static and dynamic wear leveling
– Uncorrectable bit error rate (UBER): <1 sector
per 1015 bits read
• Low power consumption
– <200mW TYP 4
• Endurance: Total bytes written (TBW) – 72TB
• Capacity5 (unformatted): 128GB, 256GB
• Mechanical – 5mm height
– mSATA connector: 3.3V ±5%
– Caseless design: 50.80mm x 29.85mm x 3.75mm
– Weight: 10g (MAX)
• Field-updateable firmware
• Operating temperature
– Commercial (0°C to +70°C)6
Micron® 25nm MLC NAND Flash
RoHS-compliant package
SATA 6 Gb/s interface
ATA modes supported
– PIO mode 3, 4
– Multiword DMA mode 0, 1, 2
– Ultra DMA mode 0, 1, 2, 3, 4, 5
Industry-standard, 512-byte sector size support
Native command queuing support with 32-command slot support
ATA-8 ACS2 command set compliant
ATA security feature command set and password
login support
Secure erase (data page) command set: fast and secure erase
Self-monitoring, analysis, and reporting technology
(SMART) command set
Performance1, 2
– Sequential 128k READ: up to 500 MB/s
– Sequential 128k WRITE: up to 260 MB/s
– Random 4k READ: up to 45,000 IOPS
– Random 4k WRITE: up to 50,000 IOPS
– PCMark® Vantage (HDD test suite score): up to
75,000
– READ/WRITE latency: 55µs (TYP)
Notes:
1. Typical I/O performance numbers as measured using Iometer with a queue depth of
32 and write cache enabled.
2. 4K transfers used for READ/WRITE latency
values.
3. The product achieves a mean time to failure
(MTTF) based on population statistics not
relevant to individual units.
4. Active power measured during execution of
MobileMark® 2007 with DIPM (device-initiated power management) enabled.
5. 1GB = 1 billion bytes; formatted capacity is
less.
6. Drive case temperature.
Warranty: Contact your Micron sales representative
for further information regarding the product,
including product warranties.
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
1
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
C400 mSATA NAND Flash SSD
Features
Part Numbering Information
Micron’s RealSSD™ C400 SSD is available in different configurations and densities. Visit www.micron.com for a
list of valid part numbers.
Figure 1: Part Number Chart
MT FD
D
AT xxx M AM - 1
K
x
x
xx
ES
Production Status
Micron Technology
Blank = Production
Product Family
ES = Engineering sample
FD = Flash drive
Operating Temperature Range
Drive Interface
Blank = Commercial (0°C to +70°C)
D = SATA 6.0 Gb/s
Hardware Feature Set
Drive Form Factor
Blank = Null
AT = mSATA
AA = Contact factory
AB = Contact factory
Drive Density
AC = Contact factory
128 = 128GB
Firmware Feature Set
256 = 256GB
Blank = Null
NAND Flash Type
1 = Contact factory
M = MLC
2 = Contact factory
Product Family
BOM Revision
AM = C400
For example:
1 = 1st generation
Sector Size
NAND Flash Component
1 = 512-byte
J = 32Gb, MLC, x8, 3.3V (25nm)
K = 64Gb, MLC, x8, 3.3V (25nm)
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
General Description
General Description
Micron’s RealSSD solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in
an JEDEC-standard mSATA form factor, the SSD integrates easily in existing storage infrastructures.
The SSD is designed to use the SATA interface efficiently during both READs and
WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability.
Figure 2: Functional Block Diagram
NAND
SATA
SSD
controller
NAND
NAND
NAND
NAND
DRAM
buffer
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Logical Block Address Configuration
Logical Block Address Configuration
The drive is set to report the number of logical block addresses (LBA) that will ensure
sufficient storage space for the specified density. Standard LBA settings, based on the
IDEMA standard (LBA1-02), are shown below.
Table 1: Standard LBA Settings
Total LBA
Drive Size
Max LBA
User Available Bytes
Decimal
Hexadecimal
Decimal
Hexadecimal
(Unformatted)
128GB
250,069,680
EE7C2B0
250,069,679
EE7C2AF
128,035,676,160
256GB
500,118,192
1DCF32B0
500,118,191
1DCF32AF
256,186,209,271
Physical Configuration
Table 2: mSATA Dimensions and Weight
Value
Unit
Width
29.85
mm (NOM)
Length
50.80
mm (NOM)
10
g (MAX)
3.75
mm (MAX)
Unit weight
Height
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
4
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Interface Connectors
Interface Connectors
Figure 3: SSD Interface Connections
Primary side
P1
P17
P15
Secondary side
P51
P52
P18
P2
P16
Table 3: Signal Assignments
Primary Side
Secondary Side
Pin #
Signal Name
Pin #
Signal Name
1
Reserved
Description
No connect
2
3V3
Description
+3.3V
3
Reserved
No connect
4
GND
Ground
5
Reserved
No connect
6
1V5
No connect
7
Reserved
No connect
8
Reserved
No connect
9
GND
Ground
10
Reserved
No connect
11
Reserved
No connect
12
Reserved
No connect
13
Reserved
No connect
14
Reserved
No connect
No connect
15
GND
Ground
16
Reserved
17
Reserved
No connect
18
GND
19
Reserved
No connect
20
Reserved
No connect
21
GND
Ground
22
Reserved
No connect
Differential signal pair +B
and -B
24
3V3
+3.3V
26
GND
Ground
Ground
23
+B
25
-B
27
GND
Ground
28
1V5
No connect
29
GND
Ground
30
TWI
Two-wire interface
Differential signal pair +A
and -A
32
TWI
34
GND
31
-A
33
+A
35
GND
Ground
36
Reserved
No connect
37
GND
Ground
38
Reserved
No connect
39
3V3
+3.3V
40
GND
41
3V3
+3.3V
42
Reserved
No connect
43
NC
No connect
44
Reserved
No connect
45
Optional
No connect
46
Reserved
No connect
47
Optional
No connect
48
1V5
No connect
49
DA/DSS
Drive activity LED
50
GND
Ground
51
Presence
Presence detection
52
3V3
+3.3V
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
5
Ground
Ground
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Performance
Performance
Measured performance can vary for a number of reasons. The major factors affecting
drive performance are the density of the drive and the interface of the host. Additionally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the
drive being tested varies.
Performance numbers will vary depending on the host system configuration.
Table 4: Drive Performance
Notes:
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
Density
128GB
256GB
Interface Speed
6 Gb/s
6 Gb/s
Unit
Sequential read (128k transfer)
500
500
MB/s
Sequential write (128k transfer)
175
260
MB/s
Random read (4k transfer)
45,000
45,000
IOPS
Random write (4k transfer)
35,000
50,000
IOPS
Read latency
55
55
µs
Write latency
55
55
µs
PCMark vantage
65,000
75,000
HDD score
1. Typical I/O performance numbers as measured using IOMeter with a queue depth of 32
and write cache enabled.
2. IOMeter measurements are performed on an 8GB span.
3. 4k transfers used for READ/WRITE latency values.
4. System variations may affect measured results.
5. Performance numbers are indicative of C400 firmware version 0009 and newer.
6
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Reliability
Reliability
Micron’s SSDs incorporate advanced technology for defect and error management.
They use various combinations of hardware-based error correction algorithms and
firmware-based static and dynamic wear-leveling algorithms.
Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read
out of the SSD, the data differs from what was programmed.
Table 5: Uncorrectable Bit Error Rate
Uncorrectable Bit Error Rate
Operation
1015
READ
<1 sector per
bits read
Mean Time to Failure
Mean time to failure (MTTF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction
procedures for electronic equipment.
Table 6: MTTF
MTTF (Operating Hours)1
Density
Note:
128GB
1.2 million
256GB
1.2 million
1. The product achieves a mean time to failure (MTTF) of 1.2 million hours, based on population statistics not relevant to individual units.
Endurance
Endurance for the SSD can be predicted based on the usage conditions applied to the
device, the internal NAND component cycles, the write amplification factor, and the
wear-leveling efficiency of the drive. The table below shows the drive lifetime for each
SSD density based on predefined usage conditions.
Table 7: Drive Lifetime
Density
Notes:
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
Drive Lifetime (Total Bytes Written)
128GB
72TB
256GB
72TB
1. Total bytes written calculated with the drive 90% full.
2. Access patterns are 50% sequential and 50% random and consist of the following: 5%
are 4k; 5% are 8k; 10% are 16k; 10% are 32k; 35% are 64K; and 35% are 128k.
3. GB/day can be calculated by dividing the total bytes written value by (365 × number of
years). For example: 72 TB/5 years/365 days = 40 GB/day for 5 years.
7
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Electrical Characteristics
Electrical Characteristics
Stresses greater than those listed may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
Table 8: mSATA Power Consumption
Density
Sequential Write/Read Maximum
(128k transfer)
Idle Average
Active Average
128GB
<85
150
3500
2000
mW
256GB
<85
160
4000
2200
mW
Notes:
1.
2.
3.
4.
Unit
Data taken at 25°C using a 6 Gb/s SATA interface.
Active average power measured while running MobileMark® 2007 Productivity Suite.
DIPM (device-initiated power management) enabled.
Sequential power measured in IOMETER MAX with 128KB transfer size.
Table 9: Maximum Ratings
Parameter/Condition
Symbol
Min
Max
Unit
3V3
3.14
3.46
V
TC
0
70
°C
Non-operating temperature
–40
85
°C
Rate of temperature change
–
20
°C/hour
Relative humidity (non-condensing)
5
95
%
Voltage input
Operating temperature
Notes:
1. Temperature is best measured with a thermocouple attached to the center point of the
drive controller ASIC package. This is the larger package closest to the interface connector on the primary side. Refer to Package Dimensions for details.
2. Supply voltage slew rate during asynchronous power-down should follow a slope of no
steeper than 60 mV/ms.
3. Power-off sequence: When the Micron C400 SSD is shut down, the ATA STANDBY IMMEDIATE (STBI) command should be the last command sent by the host and acknowledged
by the SSD. Failure to follow this process could result in a longer than normal time-toready (TTR) during the subsequent power-on sequence. TTR is the time from power-on
to drive ready to accept SATA commands.
Table 10: Shock and Vibration
Parameter/Condition
Specification
Operating shock
1500 G/1.0ms
Operating vibration
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
2–500Hz at 3.1G
8
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Device ID
Table 11: Identity Device
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
0
Description
General configuration bit-significant information
15
F
0b
0 = ATA device
14–8
X
0000100b
7
F
0b
1 = removable media device
Obsolete
Retired
6
F
1b
5–3
X
000b
2
V
0b
Response incomplete
1
X
0b
Retired
0
F
1
Retired
0b
Reserved
3FFFh
Obsolete
2
F
C837h
Specific configuration
3
F
0010h
Obsolete
4
F
0000h 0000h
6
F
003Fh
7
(O)V
0000h 0000h
9
( )X
0000h
Retired
10
(M)F
varies
Serial number (20 ASCII characters)
20
( )X
0000h 0000h
0000h
23
(M)F
varies
Firmware revision (8 ASCII characters)
27
(M)F
varies
Model number (40 ASCII characters)
15–8
F
80h
80h
7–0
F
10h
00h = Reserved
01h-FFh = Maximum number of logical sectors that shall be
transferred per DRQ data block on READ/WRITE MULTIPLE
commands
47
48
Retired
Obsolete
Reserved for assignment by the CompactFlash™ Association
Retired/Obsolete
Trusted Computing feature set options
15
F
14
F
13–1
F
0
F
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
0b
Shall be cleared to zero
1b
Shall be set to one
0000000000000b Reserved for the Trusted Computing Group
0b
1=Trusted Computing feature set is support
9
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
49
Description
Capabilities
15–14
F
00b
Reserved for the IDENTIFY PACKET DEVICE command.
13
F
1b
1 = Standby timer values as specified in this standard are
supported
0 = Standby timer values shall be managed by the device
12
F
0b
Reserved for the IDENTIFY PACKET DEVICE command.
11
F
1b
1= IORDY supported
10
F
1b
1 = IORDY may be disabled
1b
1 = LBA supported
1 = DMA supported.
0 = IORDY may be supported
9
8
F
1b
7–0
F
00000000b
50
Capabilities
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13–2
F
000000000000b
Reserved
1
X
0b
Obsolete
0
F
1b
Shall be set to one to indicate a vendor specific standby timer value minimum.
( )X
0000h 0000h
51
53
Obsolete
15–3
F
2
F
1b
1 = the fields reported in word 88 are valid
0 = the fields reported in word 88 are not valid
1
F
1b
1 = the fields reported in words (70:64) are valid
0 = the fields reported in words (70:64) are not valid
0
X
1b
Obsolete
()X
3FFFh 0010h
003Fh FC10h
00FBh
Obsolete
15
F
0b
1 = The BLOCK ERASE EXT command is supported
14
F
0b
1 = The OVERWRITE EXT command is supported
13
F
0b
1 = The CRYPTO SCRAMBLE EXT command is supported
1 = The Sanitize feature set is supported
54
59
Retired
0000000000000b Reserved
12
F
0b
11–9
F
000b
8
V
1b
7–0
V
00000001b
60
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
M(F)
Reserved
1 = Multiple sector setting is valid
xxh = Current setting for number of logical sectors that shall
be transferred per DRQ data block on READ/WRITE MULTIPLE commands
Varies by capacity Total number of user addressable logical sectors
10
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
62
63
64
Default Value
Description
()X
0000h
Obsolete
15–11
F
00000b
Reserved
10
V
0b
1 = Multiword DMA mode 2 is selected
0 = Multiword DMA mode 2 is not selected
9
V
0b
1 = Multiword DMA mode 1 is selected
0 = Multiword DMA mode 1 is not selected
8
V
0b
1 = Multiword DMA mode 0 is selected
0 = Multiword DMA mode 0 is not selected
7–3
F
0000b
2
F
1b
1 = Multiword DMA mode 2 and below are supported
1
F
1b
1 = Multiword DMA mode 1 and below are supported
0
F
1b
1 = Multiword DMA mode 0 is supported
15–8
F
0
7–0
Reserved
Reserved
F
03h
65
F
0078h
PIO modes supported
Minimum Multiword DMA transfer cycle time per word
Cycle time in nanoseconds
66
F
0078h
Manufacturer's recommended Multiword DMA transfer cycle time
Cycle time in nanoseconds
67
F
0078h
Minimum PIO transfer cycle time without flow control
Cycle time in nanoseconds
68
F
0078h
Minimum PIO transfer cycle time with IORDY flow control
Cycle time in nanoseconds
69
F
Additional Supported
15
F
0b
1 = CFast Specification Support
14
F
1b
1 = Deterministic read after Trim is supported
13
F
0b
1 = Long Physical Sector Alignment Error Reporting Control
is supported
12
F
0b
1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE
CONFIGURATION SET DMA are supported
11
F
0b
1 = READ BUFFER DMA is supported
10
F
0b
1 = WRITE BUFFER DMA is supported
9
F
0b
1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA
are supported
8
F
0b
1 = DOWNLOAD MICROCODE DMA is supported
7
F
0b
Reserved for IEEE-1667
6
F
0b
1 = Optional ATA device 28-bit commands supported
5
F
0b
1 = Read zero after Trim is supported
4–0
F
00000b
Reserved
F
0000h
Reserved
70
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
11
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
71
F
Default Value
0000h 0000h
0000h 0000h
75
Description
Reserved for the IDENTIFY PACKET DEVICE command
Queue depth
15–5
F
00000000000b
4–0
F
11111b
76
Reserved
Maximum queue depth - 1
Serial ATA Capabilities
15–13
F
000b
Reserved
12
F
1b
Supports Native Command Queuing priority information
11
F
0b
Supports Unload while NCQ commands outstanding
10
F
1b
Supports Phy event counters
9
F
1b
Supports receipt of host initiated interface power management requests
NOTE: HIPM is disabled (bit 9 = 0) for firmware versions
000G and newer
Supports native Command Queueing
8
F
1b
7–4
F
0000b
3
F
1b
1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s)
2
F
1b
1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s)
1
F
1b
1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s)
0
F
0b
Reserved (set to 0)
77
Reserved for future Serial ATA signaling speed grades
Serial ATA Additional capabilities
15–6
F
0000000000b
5
F
0b
Supports NCQ Queue Management Command
4
F
0b
Supports NCQ Streaming
3–1
V
010b
0
F
0b
15–7
F
000000000b
6
F
1b
1 = supports software settings preservation
5
F
0b
Reserved
4
F
0b
1 = supports in-order data delivery
3
F
1b
1 = supports dev initiate interface power management
2
F
1b
1 = supports DMA Setup Auto-Activate optimization
1
F
0b
1 = supports non-zero buffer offsets in DMA Setup FIS
0
F
0b
Reserved (set to 0)
78
Reserved for future Serial ATA definition
Coded value indicating current negotiated Serial ATA signal
speed
Shall be cleared to zero
Serial ATA features Supported
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
Reserved
12
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
79
Description
Serial ATA features Enabled
15–7
V
000000000b
6
V
1b
1 = software settings preservation enabled
5
V
0b
1 = Asynchronous notification enabled
4
V
0b
1 = in-order data delivery enabled
3
V
0b
1 = device initiating interface power management enabled
2
V
0b
1 = DMA Setup Auto-Activate optimization enabled
1
V
0b
1 = non-zero buffer offsets in DMA Setup FIS enabled
0
V
0b
Reserved (set to 0)
80
Reserved
Major revision number
15–10
F
000000b
9
F
1b
1 = supports ATA8-ACS2
8
F
1b
1 = supports ATA8-ACS
7
F
1b
1 = supports ATA/ATAPI-7
6
F
1b
1 = supports ATA/ATAPI-6
5
F
1b
1 = supports ATA/ATAPI-5
4
F
1b
1 = supports ATA/ATAPI-4
3
F
1b
Obsolete
2
S
0b
Obsolete
1
S
0b
Obsolete
0
F
0b
Reserved
F
0028h
81
Reserved
Minor revision number
0028h = ATA8-ACS version 6
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
13
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
82
Description
Command set supported
15
X
0b
Obsolete
14
F
1b
1 = NOP command supported
13
F
1b
1 = READ BUFFER command supported
12
F
1b
1 = WRITE BUFFER command supported
11
X
0b
Obsolete
10
F
1b
1 = Host Protected Area feature set supported
9
F
0b
1 = DEVICE RESET command supported
8
F
0b
1 = SERVICE interrupt supported
7
F
0b
1 = release interrupt supported
6
F
1b
1 = read look-ahead supported
5
F
1b
1 = write cache supported
4
F
0b
Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3
F
1b
1 = mandatory Power Management feature set supported
2
F
0b
Obsolete
1
F
1b
1 = Security feature set supported
0
F
1b
1 = SMART feature set supported
83
Command set supported
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = FLUSH CACHE EXT command supported
12
F
1b
1 = mandatory FLUSH CACHE command supported
11
F
1b
1 = Device Configuration Overlay feature set supported
10
F
1b
1 = 48-bit Address feature set supported
9
F
0b
1 = Automatic Acoustic Management feature set supported
8
F
1b
1 = SET MAX security extension supported
7
F
0b
See Address Offset Reserved Area Boot INCITS TR27:2001
6
F
0b
1 = SET FEATURES subcommand required to spin-up after
power-up
5
F
0b
1 = Power-Up In Standby feature set supported
4
F
0b
Obsolete
3
F
1b
1 = Advanced Power Management feature set supported
2
F
0b
1 = CFA feature set supported
1
F
0b
1 = READ/WRITE DMA QUEUED supported
0
F
1b
1 = DOWNLOAD MICROCODE command supported
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
14
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
84
Description
Command set/feature supported extension
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12
F
0b
Reserved for technical report INCITS TR-37-2004 (TLC)
11
F
0b
Reserved for technical report INCITS TR-37-2004 (TLC)
10–9
F
00b
Obsolete
8
F
1b
1 = 64-bit Word wide name supported
7
F
0b
1 = WRITE DMA QUEUED FUA EXT command supported
6
F
1b
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5
F
1b
1 = General Purpose Logging feature set supported
4
F
0b
1 = Streaming feature set supported
3
F
0b
1 = Media Card Pass Through Command feature set supported
2
F
0b
1 = Media serial number supported
1
F
1b
1 = SMART self-test supported
0
F
1b
1 = SMART error logging supported
85
Command set/feature enabled.
15
X
0b
Obsolete
14
F
1b
1 = NOP command supported
13
F
1b
1 = READ BUFFER command supported
12
F
1b
1 = WRITE BUFFER command supported
11
X
0b
Obsolete
10
V
1b
1 = Host Protected Area feature set enabled
9
F
0b
1 = DEVICE RESET command supported
8
V
0b
1 = SERVICE interrupt enabled
7
V
0b
1 = release interrupt enabled
6
V
1b
1 = look-ahead enabled
5
V
1b
1 = write cache enabled
4
F
0b
Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3
F
1b
Power Management feature set is enabled
2
F
0b
Obsolete
1
V
0b
1 = Security Mode feature set enabled
0
V
1b
1 = SMART feature set enabled
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
15
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
86
Description
Command set/feature enabled.
15
1b
1 = Words 120-119 are valid
14
F
0b
1 = Reserved
13
F
1b
1 = FLUSH CACHE EXT command supported
12
F
1b
1 = FLUSH CACHE command supported
11
F
1b
1 = Device Configuration Overlay supported
10
F
1b
1 = 48-bit Address features set supported
9
V
0b
1 = Automatic Acoustic Management feature set enabled
8
F
0b
1 = SET MAX security enabled by SET MAX SET PASSWORD
7
F
0b
Reserved for address Offset Reserved Area Boot, INCITS
TR27:2001
6
F
0b
1 = SET FEATURES subcommand required to spin-up after
power-up
5
V
0b
1 = Power-Up In Standby feature set enabled
4
V
0b
Obsolete
3
V
1b
1 = Advanced Power Management feature set enabled
2
F
0b
1 = CFA feature set supported
1
F
0b
1 = READ/WRITE DMA QUEUED command supported
0
F
1b
1 = DOWNLOAD MICROCODE command supported
87
Command set/feature enabled/supported
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
1b
1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12
V
0b
Reserved for technical report- INCITS tr-37-2004 (TLC)
11
V
0b
Reserved for technical report- INCITS TR-37-2004 (TLC)
10–9
F
00b
Obsolete
8
F
1b
1 = 64-bit Word wide name supported
7
F
0b
1 = WRITE DMA QUEUED FUA EXT command supported
6
F
1b
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5
F
1b
1 = General Purpose Logging feature set supported
4
V
0b
Obsolete
3
V
0b
1 = Media Card Pass Through Command feature set supported
2
V
0b
1 = Media serial number is valid
1
F
1b
1 = SMART self-test supported
0
F
1b
1 = SMART error logging supported
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
16
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
88
Default Value
Description
0b
Ultra DMA modes
15
0b
Reserved
14
0b
1 = Ultra DMA mode 6 is selected
0 = Ultra DMA mode 6 is not selected
13
0b
1 = Ultra DMA mode 5 is selected
0 = Ultra DMA mode 5 is not selected
12
0b
1 = Ultra DMA mode 4 is selected
0 = Ultra DMA mode 4 is not selected
11
0b
1 = Ultra DMA mode 3 is selected
0 = Ultra DMA mode 3 is not selected
10
0b
1 = Ultra DMA mode 2 is selected
0 = Ultra DMA mode 2 is not selected
9
0b
1 = Ultra DMA mode 1 is selected
0 = Ultra DMA mode 1 is not selected
8
0b
1 = Ultra DMA mode 0 is selected
0 = Ultra DMA mode 0 is not selected
7
0b
Reserved
6
0b
1 = Ultra DMA mode 6 and below are supported
5
1b
1 = Ultra DMA mode 5 and below are supported
4
1b
1 = Ultra DMA mode 4 and below are supported
3
1b
1 = Ultra DMA mode 3 and below are supported
2
1b
1 = Ultra DMA mode 2 and below are supported
1
1b
1 = Ultra DMA mode 1 and below are supported
0
1b
1 = Ultra DMA mode 0 IS supported
89
(O)F
0001h
Time required for security erase unit completion
90
(O)F
0001h
Time required for Enhanced security erase completion
91
(O)V
00FEh
Current advanced power management value
92
(O)V
FFFEh
Master Password Revision Code
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
17
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
93
Description
Shall be 0000h for SATA devices
15
0b
Shall be cleared to zero
14
0b
Shall be set to one
13
0b
1 = device detected CBLID-above VIH
0 = device detected CBLID-below VIL
Device 1 hardware reset result
Device 0 shall clear these bits to zero
Device 1 shall set these bits as follows:
12
0b
Reserved
11
0b
0 = Device 1 did not assert PDIAG1 = Device 1 asserted PDIAG-
10–9
These bits indicate how Device 1 determined the device
number:
00 = Reserved
01 = a jumper was used
10 = the CSEL signal was used
11 = some other method was used or the method is unknown
8
0b
Shall be set to one
Device 0 hardware reset result. Device 1 shall clear these
bits to zero.
Device 0 shall set these bits as follows:
94
7
0b
Reserved
6
0b
0 = Device 0 does not respond when Device 1 is selected.
1 = Device 0 responds when Device 1 is selected.
5
0b
0 = Device 0 did not detect the assertion of DASP1 = Device 0 detected the assertion of DASP-
4
0b
0 = Device 0 did not detect the assertion of PDIAG1 = Device 0 detected the assertion of PDIAG-
3
0b
0 = Device 0 failed diagnostics.
1 = Device 0 passed diagnostics.
2–1
00b
These bits indicate how Device 0 determined the device
number:
00 = Reserved
01 = a jumper was used
10 = the CSEL signal was used
11 = some other method was used or the method is unknown
0
0b
Shall be set to one
00h
Vendor's recommended acoustic management value
V
00h
Current automatic acoustic management value
(O)V
0000h
15–8
7–0
95
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
F
Stream Minimum Request Size
18
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
Description
96
(O)V
0000h
Streaming Transfer Time - DMA
97
(O)V
0000h
Streaming Access Latency - DMA and PIO
98
(O)F
100
V
0000h 0000h
104
(O)V
0000h
Streaming Transfer Time - PIO
105
( )F
0008h
Maximum number of 512-byte blocks of LBA Range Entries
per DATA SET MANAGEMENT command
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13
F
0b
1 = Device has multiple logical sectors per physical sector
1 = Device Logical Sector Longer than 256 Words
106
Physical sector size / Logical Sector Size
12
F
0b
11–4
F
00000000b
3–0
F
0000b
2^x logical sectors per physical sector
(O)F
0000h
Inter-seek delay for ISO-7779 acoustic testing in microseconds
0101b
NAA (3-0)
107
108
15–12
F
11–0
109
Streaming Performance Granularity(98-99)
Varies by capacity Maximum user LBA for 48-bit Address feature set
15–4
F
3–0
Reserved
000000001010b
IEEE OUI (23-12)
000001110101b
IEEE OUI (11-0)
Varies
Unique ID (35-32)
110
(M)F
Varies
5-0 Unique ID (31-16)
111
(M)F
Varies
Unique ID (15-0)
112
(O)F
0000h 0000h
0000h 0000h
116
(O)V
0000h
117
(O)F
0000h 0000h
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
Reserved for 128 bit world wide name extension to 128 bits
Reserved for INCITS TR-37-2004
Words per Logical Sector
19
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
119
Description
Commands and feature sets supported (Continued from
words 84-82)
15
F
0b
Shall be cleared to zero
Shall be set to one
14
F
1b
13–6
F
00000001b
5
F
0b
1 = Free-fall Control feature set is supported
4
F
1b
1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3
F
1b
1 = READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported
2
F
1b
1 = The Write-Read-Verify feature set is supported
1
F
1b
1 = Feature set "Disable Data Transfer After Error Detection" is supported
0
F
0b
Reserved for DDT
120
Reserved
Commands and feature sets supported or enabled (Continued from words 87-85)
15
0b
Shall be cleared to zero
14
1b
Shall be set to one
13–6
00000000b
5
0b
1 = Free-fall Control feature set is enabled
4
1b
1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3
1b
1 = The READ LOG DMA EXT and WRITE LOG DMA EXT
commands are supported
2
1b
1 = The WRITE UNCORRECTABLE EXT command is supported
1
0b
1 = The Write-Read-Verify feature set is enabled
0
0b
1= Feature set "Disable Data Transfer After Error Detection"
is enabled
0 = Feature set "Disable Data Transfer After Error Detection" is disabled
121
F
0000h 0000h
0000h 0000h
0000h 0000h
127
(O)
0000h
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
Reserved
Reserved for expanded supported and enabled settings
Obsolete
20
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
128
Security status
15–9
F
0000000b
Reserved
8
V
0b
Security level 0 = High, 1 = Maximum
7–6
F
00b
Reserved
5
F
1b
1 = Enhanced security erase supported
4
V
0b
1 = Security count expired
3
V
0b
1 = Security frozen
2
V
0b
1 = Security locked
1
V
0b
1 = Security enabled
0
F
1b
1 = Security supported
( )X
Vendor specific
data
129
160
Vendor specific
CFA power mode 1
15
F
0b
Word 160 supported
14
F
0b
Reserved
13
F
0b
CFA power mode 1 is required for one or more commands
implemented by the device
12
V
0b
CFA power mode 1 disabled
11–0
F
000000000000b
X
0000h 0000h
0000h 0000h
0000h 0000h
0000h
15–4
F
000h
3-0
F
5h
161
168
Description
169
Maximum current in ma
Reserved for assignment by the CompactFlash Association
Reserved
Device Nominal Form Factor
DATA SET MANAGEMENT command support
15–1
F
0
F
1b
170
F
0000h 0000h
0000h 0000h
Additional Product Identifier
174
F
0000h 0000h
Reserved
176
(O)V
Varies
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
000000000000000 Reserved
b
1 = the Trim bit in the DATA SET MANAGEMENT command
is supported
Current media serial number (60 ASCII characters)
21
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
206
Description
SCT Command Transport
15–12
X
0000b
11–6
F
000000b
5
F
1b
SCT Command Transport Data Tables supported
4
F
1b
CT Command Transport Features Control supported
3
F
1b
SCT Command Transport Error Recovery Control supported
2
F
1b
SCT Command Transport Write Same supported
1
F
0b
SCT Command Transport Long Sector Access supported
0
F
1b
SCT Command Transport supported
( )F
0000h 0000h
207
209
(O)
Vendor Specific
Reserved
Reserved for CE-ATA
Alignment of logical blocks within a larger physical block
15
F
0b
Shall be cleared to zero
14
F
1b
Shall be set to one
13–0
F
00000000000000b 'Logical sector' offset within the first physical sector where
the first logical
sector is placed.
210
(O)V
0000h 0000h
Write-Read-Verify Sector Count Mode 3 Only
212
(O)F
0000h 0001h
Verify Sector Count Mode 2 Only
214
(O)
NV Cache Capabilities
15–12
F
0000b
NV Cache feature set version
11–8
F
0000b
NV Cache Power Mode feature set version
7–5
F
000b
Reserved
4
V
0b
1 = NV Cache feature set enabled
3–2
F
00b
Reserved
1
V
0b
1 = NV Cache Power Mode feature set enabled
0
F
0b
1 = NV Cache Power Mode feature set supported
215
(O)V
0000h
NV Cache Size in Logical Blocks (LSW)
216
(O)V
0000h
NV Cache Size in Logical Blocks (MSW)
217
(M)F
0001h
Nominal media rotation rate (ATA8-ACS 1699-D Revision 6)
NV Cache Read Transfer Speed in MB/s (ATA8-ACS 1699-D
Revision 3f)
218
(O)V
0000h
15–8
F
00h
Reserved
7–0
F
00h
Device Estimated Time to Spin Up in Seconds
15–8
F
00h
Reserved
7–0
V
00h
Write-Read-Verify feature set current mode
219
220
NV Cache Write Transfer Speed in MB/s
NV Cache Options
221
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
0000h
Reserved
22
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Device ID
Table 11: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value
222
Description
Transport Major revision number. 0000h or FFFFh = device
does not report version
15–12
0001b
Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved
Parallel (Type = 0) Serial (Type = 1)
11–6
000000b
5
1b
Reserved SATA Rev 3.0
4
1b
Reserved SATA Rev 2.6
3
1b
Reserved SATA Rev 2.5
2
1b
Reserved SATA II: Extensions
1
1b
Reserved SATA 1.0a
0
1b
ATA8-APT ATA8-AST
Reserved Reserved
223
(M)F
0000h
224
( )F
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
234
(O)F
0001h
Minimum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3
235
00FFh
Maximum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3
236
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h
255
(M)F
Transport Minor revision number
Reserved for CE-ATA
Reserved
Integrity word
15–8
varies
Checksum
7–0
A5h
Signature
Note:
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
1. F = The content of the word is fixed and does not change.
V = The content of the word is variable and may change depending on the state of the
device or the commands executed by the device.
X = The content of the word may be fixed or variable.
R = The content of the word is reserved and will be zero.
23
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Commands
Commands
Table 12: Supported ATA Command Set
See ATA-8 standard for command details
Command Name
Command Code (hex)
CHECK POWER MODE
98h or E5h
DEVICE CONFIGURATION RESTORE
B1h/C1h
DEVICE CONFIGURATION FREEZE LOCK
B1h/C3h
DEVICE CONFIGURATION IDENTIFY
B1h/C1h
DEVICE CONFIGURATION SET
B1h/C3h
DOWNLOAD MICROCODE
92h
EXECUTE DEVICE DIAGNOSTIC
90h
FLUSH CACHE
E7h
FLUSH CACHE EXT
EAh
IDENTIFY DEVICE
ECh
IDLE
E3h or 97h
IDLE IMMEDIATE
E1h or 95h
INITIALIZE DEVICE PARAMETERS
91h
NOP
00h
READ BUFFER
E4h
READ DMA (with retry)
C8h
READ DMA (without retry)
C9h
READ DMA EXT
25h
READ FPDMA QUEUED
60h
READ LOG EXT
2Fh
READ MULTIPLE
C4h
READ MULTIPLE EXT
29h
READ NATIVE MAX ADDRESS
F8h
READ NATIVE MAX ADDRESS EXT
27h
READ SECTOR(S) EXT
24h
READ SECTOR(S) (with retry)
20h
READ SECTOR(S) (without retry)
21h
READ VERIFY SECTOR EXT
42h
READ VERIFY SECTOR(S) (with retry)
40h
SCT WRITE SAME
02h/0001h
02h/0002h
02h/0101h
02h/0102h
SCT RETURN ERROR RECOVERY CONTROL
030h/01h
SCT SET ERROR RECOVERY CONTROL
03h/01h
SCT SET FEATURE CONTROL
04h/01h
SCT RETURN FEATURE CONTROL
04h/02h
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
24
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Commands
Table 12: Supported ATA Command Set (Continued)
See ATA-8 standard for command details
Command Name
Command Code (hex)
SCT RETURN FEATURE OPTION FLAG
04h/03h
SCT RETURN SCT DATA TABLE
05h/01h
SECURITY DISABLE PASSWORD
F6h
SECURITY ERASE PREPARE
F3h
SECURITY ERASE UNIT
F4h
SECURITY FREEZE LOCK
F5h
SECURITY SET PASSWORD
F1h
SECURITY UNLOCK
F2h
SEEK
7xh
SET FEATURES
EFh
SET MAX ADDRESS
F9h
SET MAX – FREEZE LOCK
F9h/04h
SET MAX – LOCK
F9h/02h
SET MAX ADDRESS EXT
37h
SET MULTIPLE MODE
C6h
SET MAX – SET PASSWORD
F9h/01h
SET MAX – UNLOCK
F9h/03h
SLEEP
E6h or 99h
SMART DISABLE OPERATIONS
B0h/D9h
SMART ENABLE OPERATIONS
B0h/D8h
SMART ENABLE/DISABLE AUTOSAVE
B0h/D2h
SMART EXECUTE OFF-LINE IMMEDIATE
B0h/D4h
SMART READ DATA
B0h/D0h
SMART READ LOG SECTOR
B0h/D5h
SMART RETURN STATUS
B0h/DAh
SMART WRITE LOG
B0h/D6h
STANDBY
E2h or 96h
STANDBY IMMEDIATE
E0h or 94h
WRITE BUFFER
E8h
WRITE DMA (with retry)
CAh
WRITE DMA (without retry)
CBh
WRITE DMA EXT
35h
WRITE DMA FUA EXT
3Dh
WRITE FPDMA QUEUED
61h
WRITE LOG EXT
3Fh
WRITE MULTIPLE
C5h
WRITE MULTIPLE EXT
39h
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
25
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Commands
Table 12: Supported ATA Command Set (Continued)
See ATA-8 standard for command details
Command Name
Command Code (hex)
WRITE MULTIPLE FUA EXT
CEh
WRITE SECTOR(S) (with retry)
30h
WRITE SECTOR(S) EXT
34h
WRITE UNCORRECTABLE EXT
45h
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
26
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Compliance
Compliance
Micron SSDs comply with the following:
•
•
•
•
•
•
•
•
•
•
•
RoHS “green”
CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003
FCC: CFR Title 47, Part 15, ICES-003, all Class B
UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition
BSMI (Taiwan): approval to CNS 13438
C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22
KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B
W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations
may apply to customers who place these products in the markets where WEEE is enforced.
TUV (Germany): approval to IEC60950/EN60950
VCCI
IC (Canada):
- This Class B digital apparatus complies with Canadian ICES-003.
- Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Rules
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
27
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Package Dimensions
Package Dimensions
Figure 4: mSATA Package – 50.80mm
2.60mm
DIA THRU
0.102in
(2 PLCS)
3.11mm
0.122in
P1
0.75mm
RAD
0.030in
3.75mm
0.148in
1.00mm
RAD
0.039in
(2 PLCS)
5.69mm
0.224in
1.40mm
0.055in
1.00mm
0.039in
1.35mm
0.053in
4.34mm
0.171in
3.53mm
0.139in
(2 PLCS)
2.83mm
0.111in
2.08mm
0.082in
11.08mm
0.436in
29.85mm
1.175in
2.08mm
0.082in
2.83mm
0.111in
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
2.75mm
0.108in
5.27mm
0.207in
50.80mm
2.000in
28
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
References
References
• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available
at www.sata-io.org
• SATA 3.0 GOLD
• ATA-8 ACS2
• JEDEC MO-300B (mSATA SSD Assembly)
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
29
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
C400 mSATA NAND Flash SSD
Revision History
Revision History
Rev. D – 8/12
•
•
•
•
Changed MTBF to MTTF.
Added new power-off sequence note to Maximum Ratings table.
Updated note 3 (GB/day) under Drive Lifetime table.
Added new note to Word 76 in Device ID table.
Rev. C – 4/12
• In Features section, removed reference to hot-plug-capable and changed caseless design height from 3.80mm to 3.75mm.
• In Physical Configuration section, changed height from 3.80mm to 3.75mm.
• Updated package dimensions figure (mSATA Package – 50.80mm):
– 3.80mm to 3.75mm
– 0.150in to 0.148in
– 1.40mm to 1.35mm
– 0.055in to 0.053in
Rev. B – 3/12
• Production status.
Rev. A – 10/11
• Initial release.
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur.
PDF: 09005aef8484bfff
realssd_c400_msata.pdf - Rev. D 8/12 EN
30
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
Similar pages