RoHS Compliant Compact Flash 4 Series Specification for Industrial CF November 17, 2009 Version 1.1 Apacer Technology Inc. 4th Fl., 75 Hsin Tai Wu Rd., Sec.1, Hsichih, Taipei Hsien 221, Taiwan Tel: +886-2-2698-2888 Fax: +886-2-2698-2889 www.apacer.com Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX Features: CompactFlash Association Specification Revision 4.1 Standard Interface – 512 bytes per sector – ATA command set compatible – ATA mode support for up to: PIO Mode-6 Multiword DMA Mode-4 Ultra DMA Mode-6 Capacities – 256, 512 MB 1, 2, 4, 8, 16 GB Sustained read performance – Up to 50 MB/sec Sustained write performance – Up to 21 MB/sec Flash management – Advanced wear-leveling algorithms to substantially increase longevity of flash media – Built-in ECC support for correcting up to 8/15 random single-bit errors per 512byte sector – Read Recovery Technology – Power Failure Recovery – S.M.A.R.T. Technology Temperature ranges Operation: 0°C to 70°C (Standard) -40°C to 85°C(ET*) – Storage: -40°C to 100°C – Support for voltage read and write operations – 3.3 V or 5 V – – Low power consumption (typical) Active mode: 95 mA/ 90 mA (3.3 V/ 5 V) Sleep mode: 0.2 mA/ 0.2 mA (3.3 V/ 5 V) – Connector Type 50 pins female – Physical Dimensions 36.4mm x 42.8mm x 3.3mm RoHS compliant NAND Flash Type: SLC *Extended Temperature 1 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX Table of Contents 1. GENERAL DESCRIPTION ......................................................................................... 3 1.1 PERFORMANCE-OPTIMIZED CONTROLLER ........................................................................................... 3 1.1.1 FIFO Buffer.............................................................................................................................. 3 1.1.2 Error Correction Code (ECC) ................................................................................................... 3 2. FUNCTIONAL BLOCK ............................................................................................... 4 3. PIN ASSIGNMENTS ................................................................................................... 5 4. CAPACITY SPECIFICATION ..................................................................................... 7 4.1 PERFORMANCE SPECIFICATION .......................................................................................................... 7 4.2 ENVIRONMENTAL SPECIFICATIONS ...................................................................................................... 7 5. FLASH MANAGEMENT ............................................................................................ 8 5.1 ADVANCED W EAR LEVELING .............................................................................................................. 8 5.2 READ RECOVERY TECHNOLOGY ......................................................................................................... 8 5.3 POWER FAILURE RECOVERY .............................................................................................................. 8 5.4 S.M.A.R.T. TECHNOLOGY ................................................................................................................. 8 6. SOFTWARE INTERFACE ......................................................................................... 9 6.1 CF-ATA COMMAND SET ................................................................................................................... 9 7. ELECTRICAL SPECIFICATION .............................................................................. 11 7.1 ABSOLUTE MAXIMUM RATINGS ......................................................................................................... 11 7.2 RECOMMENDED OPERATING CONDITIONS ......................................................................................... 11 7.3 DC CHARACTERISTICS .................................................................................................................... 12 7.4 CAPACITANCE ................................................................................................................................ 12 7.5 INTEGRATED SERIES TERMINATION RESISTOR ................................................................................... 12 7.6 POWER SUPPLY SEQUENCE ............................................................................................................ 13 7.7 SETUP TIME ................................................................................................................................... 13 8. PHYSICAL CHARACTERISTICS ............................................................................ 14 8.1 DIMENSION .................................................................................................................................... 14 9. PRODUCT ORDERING INFORMATION ................................................................. 15 9.1 PRODUCT CODE DESIGNATIONS ....................................................................................................... 15 9.2 VALID COMBINATIONS ..................................................................................................................... 16 9.2.1 Standard Temperature .......................................................................................................... 16 9.2.2 Extended Temperature ......................................................................................................... 18 2 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 1. General Description Apacer’s Compact Flash 4 offers the most reliable and high performance storage which is compatible with CF Type I and Type II devise. Unlike the others, Apacer Compact Flash 4 provides solid traceability to ensure all products HW/SW are the same as you qualified. Apacer’s Compact Flash 4 complies with the interfaces, such as the commands, timings, and protocols based on the Compact Flash Specification (CFA standard), and operates as the PC Card ATA interface providing complete PCMCIA - ATA functionality and compatibility. Apacer ‘s Compact Flash 4 is designed for use in Point of Sale (POS) terminals, telecom, IP-STB, medical instruments, surveillance systems, industrial PCs and handheld applications. 1.1 Performance-Optimized Controller Compact Flash 4 Controller translates standard CF signals into flash media data and control signals. 1.1.1 FIFO Buffer Compact Flash 4 Controller performs as an FIFO buffer to optimize the host’s data transfer to and from the flash media for reliable storage via performing data correction and moving data to another block in case of the correctable error. 1.1.2 Error Correction Code (ECC) Compact Flash 4 adopts Error Detection Code (EDC) and Error Correction Code (ECC) algorithms which correct up to 8/15 random single-bit errors for each 512-byte block of data. High performance is achieved through hardware-based error detection and correction. 3 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 2. Functional Block Compact Flash 4 Card includes a controller and flash media, as well as the standard Compact Flash interface. Figure 2-1 shows the functional block diagram. Flash Array Flash Media Compact Flash Interface Flash Media Compact Flash Controller Flash Media Flash Media Figure 2-1: Functional block diagram 4 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 3. Pin Assignments Table 3-1 lists the pin assignments with respective signal names for the 50-pin configuration. A “#” suffix indicates the active low signal. The pin type can be input, output or input/output. Table 3-1: Pin assignments (1 of 2) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Memory card mode Signal name GND D3 D4 D5 D6 D7 #CE1 A10 #OE A9 A8 A7 VCC A6 A5 A4 A3 A2 A1 A0 D0 D1 D2 WP #CD2 #CD1 D11 D12 D13 D14 D15 #CE2 #VS1 #IORD #IOWR #WE RDY/-BSY VCC #CSEL #VS2 RESET Pin I/O type I/O I/O I/O I/O I/O I I I I I I I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I I I O I O I I/O card mode Signal name GND D3 D4 D5 D6 D7 #CE1 A10 #OE A9 A8 A7 VCC A6 A5 A4 A3 A2 A1 A0 D0 D1 D2 #IOIS16 #CD2 #CD1 D11 D12 D13 D14 D15 #CE2 #VS1 #IORD #IOWR #WE #IREQ VCC #CSEL #VS2 RESET Pin I/O type I/O I/O I/O I/O I/O I I I I I I I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I I I O I O I True IDE mode Signal name GND D3 D4 D5 D6 D7 #CS0 1 A10 #ATA SEL 1 A9 1 A8 1 A7 VCC 1 A6 1 A5 1 A4 1 A3 A2 A1 A0 D0 D1 D2 #IOCS16 #CD2 #CD1 D11 D12 D13 D14 D15 #CS1 #VS1 #IORD #IOWR #WE INTRQ VCC #CSEL #VS2 #RESET Pin I/O type I/O I/O I/O I/O I/O I I I I I I I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I I I O I O I 5 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX Table 3-1: Pin assignments (2 of 2) Pin No. 42 43 44 45 46 47 48 49 50 Memory card mode Signal name #WAIT #INPACK #REG BVD2 BVD1 D8 D9 D10 GND Pin I/O type O O I O O I/O I/O I/O - I/O card mode Signal name #WAIT #INPACK #REG #SPKR #STSCHG D8 D9 D10 GND Pin I/O type O O I O O I/O I/O I/O - True IDE mode Signal name IORDY 2 DMARQ 2 DMACK #DASP #PDIAG D8 D9 D10 GND Pin I/O type O O I O O I/O I/O I/O - 1. The signal should be grounded by the host. 2. Connection required when UDMA is in use. 6 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 4. Capacity Specification Capacity specification of Compact Flash 4 series is available as shown in Table 4-1. It lists the specific capacity and the default numbers of heads, sectors and cylinders for each product line. Table 4-1: Capacity specifications 1,2 Capacity Total bytes Cylinders Heads Sectors Max LBA 256 MB 256,901,120 980 16 32 501,760 512 MB 512,483,328 993 16 63 1,000,944 1GB 1,024,966,656 1,986 16 63 2,001,888 2GB 2,048,901,120 3,970 16 63 4,001,760 4GB 4,110,188,544 7,964 16 63 8,027,712 8GB 8,195,604,480 15,880 16 63 16,007,040 16GB 16,391,208,960 16,3833 16 63 32,014,080 1. Total bytes includes reserved block. 2. Display of total bytes varies from operating systems. 3. Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies 4.1 Performance Specification Performances of Compact Flash 4 are listed below. Table 4-2: Performance specifications Capacity 256 MB 512 MB Performance 4 GB/ 8 GB 16 GB 1 GB/ 2 GB Sustained read (MB/s) 32 43 46 50 Sustained write (MB/s) 10 15~17 17 21 4.2 Environmental Specifications Environmental specification of Compact Flash 4 series follows the MIL-STD-810F standards as shown in Table 4-3. Table 4-3: Environmental specifications Environment Temperature Specification Operation 0°C to 70°C; -40°C to 85°C (Extended Temperature) Storage -40°C to 100°C Humidity Vibration (Non-Operation) Shock (Non-Operation) 5% to 95% RH (Non-condensing) Sine wave: 10~2000Hz, 15G (X, Y, Z axes) Half sine wave, Peak acceleration 50 G, 11 ms (X, Y, Z ; All 6 axes) 7 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 5. Flash Management 5.1 Advanced Wear Leveling The goal of advanced wear leveling algorithms is to evenly spread the program and erase cycles on the area of programmed and erased multiple times and the area of programmed one and read multiple times among the available blocks in the flash array. 5.2 Read Recovery Technology Read Recovery Technology enables reliable storage. When it is detected correctable error during read command operation, all data of related block is corrected and is moved to other block. Since it continues to read data after recovery operation, read data is the same as no error data for host system. However, since data transfer is stopped temporarily, the output time of BSY signal becomes long. In order to perform Read Command Recovery, it is necessary to set up the threshold for the number of detected error bit. Read Command Recovery is performed by following commands. READ DMA READ MULTIPLE READ SECTOR(S) READ VERIFY SECTOR(S) 5.3 Power Failure Recovery The controller enables to reduce data loss in case of sudden power fail. Once power was failure before cached data writing back into flash, data in the cache will lost. The next time the power is on, the controller will check these fragmented data segment, and, if necessary, replace them with old data kept in flash until programmed successfully. 5.4 S.M.A.R.T. Technology S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology and enables to expect the endurance of flash memory. The S.M.A.R.T. function protects the user from unexpected fault of product. The S.M.A.R.T function enables to predict the occurrence of near-term degradation or fault conditions by monitoring and storing critical parameters of flash memory (ex. Number of bad block, maximum number of erase, etc). The host system is warned of a negative reliability condition which is the impending risk of data loss by the S.M.A.R.T. function. Then the user can take appropriate action to minimize the risk. 8 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 6. Software Interface 6.1 CF-ATA Command Set Table 6-1 summarizes the CF-ATA command set with the paragraphs that follow describing the individual commands and the task file for each. Table 6-1: CFC-ATA command set (1/2) Command Code Command Protocol CFA Erase-Sector(s) C0H Non-data CFA Request Extended Error Code 03H Non-data CFA Translate-Sector 87H PIO data-in CFA Write-Multiple-Without-Erase CDH PIO data-out CFA Write-Sector(s)-Without-Erase 38H PIO data-out Check-Power-Mode E5H or 98H Non-data Download Microcode 92H PIO data-out Execute-Drive-Diagnostic 90H Device Diagnostic Flush-Cache E7H Non-data Format-Track 50H PIO data-out Identify-Drive ECH PIO data-in Idle E3H or 97H Non-data Idle-Immediate E1H or 95H Non-data Initialize-Drive-Parameters 91H Non-data NOP 00H Non-data Read-Buffer E4H PIO data-in Read DMA C8H or C9H DMA Read Long 22h or 23h PIO data-in Read-Multiple C4H PIO data-in Read-Sector(s) 20H or 21H PIO data-in Read-Verify-Sector(s) 40H or 41H Non-data Recalibrate 1XH Non-data Security Disable Password F6H PIO data-out Security Erase Prepare F3H Non-data Security Erase Unit F4H PIO data-out Security Freeze Lock F5H Non-data Security Set Password F1H PIO data-out Security Unlock F2H PIO data-out 9 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX Table 6-1: CFC-ATA command set (2/2) Command Code Command Protocol Seek 7XH Non-data Set-Features EFH Non-data Set-Multiple-mode C6H Non-data Sleep E6H or 99H Non-data SMART Disable Operations B0H Non-data SMART Enable/Disable Attribute Autosave B0H Non-data SMART Enable Operations B0H Non-data SMART Read Attribute Thresholds B0H PIO data-in SMART Read Data B0H PIO data-in SMART Read Log B0H PIO data-in SMART Return Status B0H Non-data Standby E2H or 96H Non-data Standby-Immediate E0H or 94H Non-data Write Buffer E8H PIO data-out Write DMA CAH or CBH DMA Write Long 32H or 33H PIO data-out Write Multiple C5H PIO data-out Write Sector(s) 30H or 31H PIO data Write Verify 3CH PIO data Write Level F5H Non-data 10 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 7. Electrical Specification 7.1 Absolute Maximum Ratings Caution: Absolute Maximum Ratings – Applied conditions greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Table 7-1: Absolute maximum ratings (Based on GND [0V]) Item Power supply voltage Input voltage Symbol VDDIO VIN(Standard) VIN(5V-Tolerant) Output current IOUT Storage temperature TSTG Rated Value -0.5~+4.6 -0.5~+4.6 -0.5~+6.6 (The power is supplied) ±11 ±21 ±29 ±45 -40~+100 Unit V V V mA mA mA mA Condition VIN < VDDIO+0.5V VIN < VDDIO+3V 3mA buffer 6mA buffer 9mA buffer 12mA buffer ℃ 7.2 Recommended Operating Conditions Table 7-2: Recommended Operating Conditions Item Input voltage Operating ambient temperature Symbol VIN(Standard) VIN(5V-Tolerant) TA Rated Value 2.7~3.6 4.5~5.5 -40~+85 Unit V V Condition ℃ 11 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 7.3 DC Characteristics Table 7-3: DC Characteristics (@ VDDIO=3.3V) Item Symbol VIH VIL V+ VVh VOH VOL IIH IIL IOZ RPU RPD Input voltage (TTL level) Schmidt trigger input (TTL level) Output voltage Input leak current Output leak current Pull-up resistance Pull-down resistance Current (VDDIO) consumption ICC33udma6 ICC33pio6 ICC33idl ICC33slp Standard Value Min Typ Max 2.0 — VDDIO 0 — 0.7 1.2 — 2.4 0.6 — 1.8 0.3 — 1.5 VDDIO-0.1 — — — — 0.1 -10 — +10 -10 — +10 -10 — +10 14.2 31.9 80.7 20.6 44.9 116.4 — 40 — — 20 — — 2 — — 0.1 — Unit V V V V V V V uA uA uA kΩ kΩ mA mA mA mA Measurement Condition VDDIO=2.7V IOH=0mA IOL=0mA VIN=VDDIO VIN=VSS Hi-Z state VIN=VSS VIN=VDDIO UDMA mode 6 (when 2ch interleave) PIO mode 6 (when 2ch interleave) IDLE SLEEP 7.4 Capacitance Table 7-4: Capacitance Item Input Pin Capacitance (5V-Tolerant) I/O Pin Capacitance (5V-Tolerant) Symbol Ci (5V-Tolerant) Cio (5V-Tolerant) Min 7 7 Typ — — Max 11 11 Unit pF pF Typ 33 Max 39 Unit Ω 7.5 Integrated Series Termination Resistor Table 7-5: Integrated Series Termination Resistor Item Terminator Resistance Symbol Rterm Min 27 INTRQ, #INPACK, IORDY, DMACK, #CS0, #CS1, #IORD, #IOWR, A[2:0] and D[15:0] (IDE mode) signals that have integrated series termination resistors. 12 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 7.6 Power Supply Sequence The controller is an IC that functions at 3.3V for the I/O power supply. There power supplies will deliver power to the chip externally, but a through current may occur inside the chip depending on the power-on and power-off sequence. For this reason, the power supply should be turned on and off simultaneously for reliability. Refer to figure 7-1. Turn on condition Time difference of VDDIO*0 to both VDDIO*0.9 is less than 100[ms]. Turn off condition Time difference of VDDIO*0.9 to both VDDIO*0.1 is less than 100[ms]. 5V tolerant buffer Before/after power supply is turned on/off, it must not apply 5V voltage. Figure 7-1 Power ON/OFF Sequence 7.7 Setup Time Hardware reset time (reset release to a ready state) is less than about 100 [ms] in PC Card/HOST Memory Bus mode. For IDE mode, it is less than about 450 [ms] when master connection, and is less than about 250 [ms] when slave connection. Setup time does not depend on the total capacity of connected flash memory. 13 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 8. Physical Characteristics 8.1 Dimension T ABLE 8-1: Type I CFC physical specification Length: Width: Thickness (Including Label Area): 36.40 +/- 0.15mm (1.433+/- 0.06 in.) 42.80 +/- 0.10mm (1.685+/- 0.04 in.) 3.3mm+/-0.10mm (0.130+/-0.04in.) Unit: mm FIGURE 8-1: Physical dimension 14 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 9. Product Ordering Information 9.1 Product Code Designations A P – CF x x x x A 5 X S – XXXXXX Specification RM: Removable NR: Non-Removable NDRM: Non-DMA + Removable NDNR: Non-DMA + Non-Removable ETRM: Ext. Temp. + Removable ETNR: Ext. Temp. + Non-Removable ETNDRM: Ext. Temp + Non-DMA + Removable ETNDNR: Ext. Temp + Non-DMA + Non-Removable Halogen Free Compliant Configuration F：Dual Channel G：Dual Channel + Interleave CTL Type CFC Type Capacities: 256M 512M 001G: 002G 004G: 008G 016G 256MB 512MB 1GB 2GB 4GB 8GB 16GB Model Name Apacer Product Code 15 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 9.2 Valid Combinations 9.2.1 Standard Temperature 9.2.1.1 Removable Capacity AP/N 256MB AP-CF256MA5FS-RM 512MB AP-CF512MA5GS-RM 1GB AP-CF001GA5GS-RM 2GB AP-CF002GA5GS-RM 4GB AP-CF004GA5GS-RM 8GB AP-CF008GA5GS-RM 16GB AP-CF016GA5GS-RM Capacity AP/N 256MB AP-CF256MA5FS-NR 512MB AP-CF512MA5GS-NR 1GB AP-CF001GA5GS-NR 2GB AP-CF002GA5GS-NR 4GB AP-CF004GA5GS-NR 8GB AP-CF008GA5GS-NR 16GB AP-CF016GA5GS-NR 9.2.1.2 Non-Removable 16 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 9.2.1.3 Non-DMA + Removable Capacity AP/N 256MB AP-CF256MA5FS-NDRM 512MB AP-CF512MA5GS-NDRM 1GB AP-CF001GA5GS-NDRM 2GB AP-CF002GA5GS-NDRM 4GB AP-CF004GA5GS-NDRM 8GB AP-CF008GA5GS-NDRM 16GB AP-CF016GA5GS-NDRM 9.2.1.4 Non-DMA + Non-Removable Capacity AP/N 256MB AP-CF256MA5FS-NDNR 512MB AP-CF512MA5GS-NDNR 1GB AP-CF001GA5GS-NDNR 2GB AP-CF002GA5GS-NDNR 4GB AP-CF004GA5GS-NDNR 8GB AP-CF008GA5GS-NDNR 16GB AP-CF016GA5GS-NDNR Note: Valid combinations are those products in mass production or will be in mass production. Consult your Apacer sales representative to confirm availability of valid combinations and to determine availability of new combinations. 17 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 9.2.2 Extended Temperature 9.2.2.1 Ext. Temp. + Removable Capacity AP/N 256MB AP-CF256MA5FS-ETRM 512MB AP-CF512MA5GS-ETRM 1GB AP-CF001GA5GS-ETRM 2GB AP-CF002GA5GS-ETRM 4GB AP-CF004GA5GS-ETRM 8GB AP-CF008GA5GS-ETRM 16GB AP-CF016GA5GS-ETRM 9.2.2.2 Ext. Temp. + Non-Removable Capacity AP/N 256MB AP-CF256MA5FS-ETNR 512MB AP-CF512MA5GS-ETNR 1GB AP-CF001GA5GS-ETNR 2GB AP-CF002GA5GS-ETNR 4GB AP-CF004GA5GS-ETNR 8GB AP-CF008GA5GS-ETNR 16GB AP-CF016GA5GS-ETNR 18 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX 9.2.2.3 Ext. Temp. + Non-DMA + Removable Capacity AP/N 256MB AP-CF256MA5FS-ETNDRM 512MB AP-CF512MA5GS-ETNDRM 1GB AP-CF001GA5GS-ETNDRM 2GB AP-CF002GA5GS-ETNDRM 4GB AP-CF004GA5GS-ETNDRM 8GB AP-CF008GA5GS-ETNDRM 16GB AP-CF016GA5GS-ETNDRM 9.2.2.4 Ext. Temp. + Non-DMA + Non-Removable Capacity AP/N 256MB AP-CF256MA5FS-ETNDNR 512MB AP-CF512MA5GS-ETNDNR 1GB AP-CF001GA5GS-ETNDNR 2GB AP-CF002GA5GS-ETNDNR 4GB AP-CF004GA5GS-ETNDNR 8GB AP-CF008GA5GS-ETNDNR 16GB AP-CF016GA5GS-ETNDNR Note: Valid combinations are those products in mass production or will be in mass production. Consult your Apacer sales representative to confirm availability of valid combinations and to determine availability of new combinations. 19 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX Revision History Revision Date Description Remark 0.1 07/31/2009 Preliminary 0.2 08/06/2009 Context revised 0.3 08/10/2009 Modified pin assignments 0.4 08/11/2009 Context revised 1.0 10/21/2009 Official release 1.1 11/17/2009 Command set revised 20 © 2009 Apacer Technology Inc. Rev. 1.1 Compact Flash 4 series AP-CFxxxxA5XS-XXXXXX Global Presence Taiwan (Headquarters) Apacer Technology Inc. th 4 Fl., 75 Hsin Tai Wu Rd., Sec.1 Hsichih, 221 Taipei Hsien Taiwan, R.O.C. Tel: +886-2-2698-2888 Fax: +886-2-2698-2889 [email protected] U.S.A. Apacer Memory America, Inc. 386 Fairview Way, Suite102, Milpitas, CA 95035 Tel: 1-408-518-8699 Fax: 1-408-935-9611 [email protected] Japan Apacer Technology Corp. 5F, Matsura Bldg., Shiba, Minato-Ku Tokyo, 105-0014, Japan Tel: 81-3-5419-2668 Fax: 81-3-5419-0018 [email protected] Europe Apacer Technology B.V. Europalaan 89 5232 BC 'S-Hertogenbosch The Netherlands Tel: 31-73-645-9620 Fax: 31-73-645-9629 [email protected] China Apacer Electronic (Shanghai) Co., Ltd 1301, No.251,Xiaomuqiao Road, Shanghai, 200032, China Tel: 86-21-5529-0222 Fax: 86-21-5206-6939 [email protected] India Apacer Technologies Pvt. Ltd. #143, 1st Floor, Raheja Arcade, 5th Block Kormangala Industrial Layout, Bangalore - 560095, India Tel: 91-80-4152-9061 [email protected] 21 © 2009 Apacer Technology Inc. Rev. 1.1 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Apacer: AP-CF004GA5GS-ETNDRM AP-CF004GA5GS-ETRM AP-CF004GA5GS-NDRM AP-CF004GA5GS-RM