MPD MA348D12RUI Ma300rui sery Datasheet

MA300RUI Series
Wide 4:1 Input, 3W,
High 3 kVDC Isolation
DC/DC Converters
Electrical Specifications
Key Features:
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
• 3W Output Power
Input
Parameter
• 4:1 Input Voltage Range
Input Start Voltage
• 3,000 VDC Isolation
• 16 Standard Models
Under Voltage Shutdown
Input Filter
• Single & Dual Outputs
Output
• Compact DIP Case
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Transient Recovery Time, See Note 2
Transient Response Deviation
Temperature Coefficient
Output Overload Protection
Output Short Circuit
• -40°C to +85°C Operation
• Industry Standard Pin-Out
1.5 kV Isolation
Models
Available
2:1 Input Range
Models
Available
Conditions
Min.
24 VDC Input
48 VDC Input
24 VDC Input
48 VDC Input
(Pi) Filter
Typ.
Conditions
Typ.
Min.
Dual Output, Balanced Loads
VIN = Min to Max
IOUT = 0% to 100%
See Note 1
±0.5
±0.3
±0.3
200
±3.0
±0.01
25% Load Step Change
Max.
9.0
18.0
8.5
17.5
Units
Max.
±2.0
±2.0
±1.0
±1.0
70
500
±5.0
±0.02
Units
%
%
%
%
mV P - P
µSec
%
%/°C
%
Max.
Units
VDC
M
pF
kHz
Foldback
120
Continuous (Autorecovery)
VDC
VDC
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI Characteristics
Parameter
Radiated Emissions
Conducted Emissions
ESD
RS
EFT
Surge
CS
Conditions
60 Seconds
500 VDC
100 kHz/1.0V
Min.
3,000
1,000
Typ.
500
90
Standard
See Note 3
See Note 3
EN 55022
EN 55022
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
Level
Class A
Class A
Criteria A; ±8 kV Air ±6 kV Contact
Criteria A; 10V/m
Criteria A; ±2 kV
Criteria A; ±1 kV
Criteria A; 10V/m
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Ambient
Case
Min.
-40
Typ.
+25
-50
Free Air Convection
RH, Non-condensing
Max.
+85
+100
+125
Units
°C
°C
°C
95
%
1.25 x 0.80 x 0.40 Inches (31.75 x 20.32 x 10.16 mm)
Non-Conductive Black Plastic (UL94-V0)
0.45 Oz (12.8g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
1.0
Typ.
Max.
Units
MHours
Conditions
24 VDC Input
48 VDC Input
1.5 mm From Case for 10 Sec
Min.
-0.7
-0.7
Typ.
Max.
50.0
100.0
260
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
°C
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
MA324S-05RUI
MA324S-05RUI
MA324S-12RUI
MA324S-15RUI
MA324S-24RUI
MA324D-05RUI
MA324D-12RUI
MA324D-15RUI
MA348S-03RUI
MA348S-05RUI
MA348S-12RUI
MA348S-15RUI
MA348S-24RUI
MA348D-05RUI
MA348D-12RUI
MA348D-15RUI
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load
24
9.0 - 36.0
134
30
24
9.0 - 36.0
158
30
24
9.0 - 36.0
152
30
24
9.0 - 36.0
151
30
24
9.0 - 36.0
154
30
24
9.0 - 36.0
130
30
24
9.0 - 36.0
152
30
24
9.0 - 36.0
152
30
48
18.0 - 75.0
67
20
48
18.0 - 75.0
78
20
48
18.0 - 75.0
75
20
48
18.0 - 75.0
74
20
48
18.0 - 75.0
76
20
48
18.0 - 75.0
65
20
48
18.0 - 75.0
76
20
48
18.0 - 75.0
76
20
Output
Voltage
Current
Current
(VDC)
(mA, Max)
(mA, Min)
3.3
5.0
12.0
15.0
24.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
24.0
±5.0
±12.0
±15.0
750.0
600.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
750.0
600.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
Notes:
1. When measuring output ripple, it is recommended that an external 3.3 µF ceramic capacitor be
placed from the +VOUT pin to the -VOUT pin for single output units and from each output to common
for dual output units.
2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.
3. Operation at no-load will not damage these units.
4. An external 220 µF/100V capacitor connected across the input pins is required to meet
EN61000-4-4 and EN61000-4-5.
5. Dual output units may be connected to provide a 10, 24 or 30 VDC output. To do this, connect the
load across the positive (+VOUT) and negative (-VOUT) outputs and float the output common.
6. The converter should be connected to a low ac-impedance source. An input source with a highly
inductive impedance may affect the stability of the converter. In applications where the converter
output loading is high and input power is supplied over long lines, it may be necessary to use
a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR
<1.0 at 100 kHz) capacitor be mounted close to the converter. For 24V input units a 4.7 µF is
recommended; and for 48V units a 2.2 µF.
7. It is recommended that a fuse be used on the input of a power supply for protection. See the table
above for the correct rating.
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
Fuse
Reflected Capacitive
Ripple
Rating
Load
Current
Slow-Blow
(µF, Max)
Efficiency
(%, Typ)
(mA Typ)
77
79
82
83
81
80
82
82
77
80
83
84
82
80
82
82
(mA)
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
680
470
330
220
100
±220
±150
±100
680
470
330
220
100
±220
±150
±100
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
Derating Curve
Mechanical Dimensions
For 1.5 kV Isolation, See MA300x-xxRU Series Datasheet
For 2:1 Inputs, See MA300x-xxRW Series Datasheet
Pin Connections
Pin
Single
Dual
2, 3
9
11
14
16
22, 23
-VIN
No Pin
NC
+VOUT
-VOUT
+VIN
-VIN
Common
-VOUT
+VOUT
Common
+VIN
NC: No Connection
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.x = ±0.02 (±0.50)
• Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages