BeRex BVA303 Digital variable gain amplifier Datasheet

BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Product Description
Figure 2. Package Type
The BVA303 is a digitally controlled variable gain amplifier (DVGA) is
featuring high linearity using the voltage 3V supply with a broadband
frequency range of 30 to 4000 MHz.
Both stages are internally matched to 50 Ohms and It is easy to use
with no external matching components required.
A serial output port enables cascading with other serial controlled
devices.
An integrated digital control interface supports both serial and parallel programming of the attenuation,
including the capability to program an initial attenuation state at
power-up.
Covering a 31.5 dB attenuation range in 0.5 dB steps.
The BVA303 is targeted for use in wireless infrastructure, point-topoint, or can be used for any general purpose wireless application.
Figure 1. Functional Block Diagram
3
C16
4
GND
5
AMPOUT
6
C2
C4
C8
RF2
P/S
VSS/GND
19
6-Bit
Digital Step
Attenuator
Gain Block
AMPLIFIER
7
BeRex
8
9
10
11
Device Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Small 24-Pin 4 x 4 mm QFN Package
Integrate DSA to Amp Functionality
Wide Power supply range of +2.7 to +5.5V(DSA)
Single Fixed +3V supply (Amp)
30-4000MHz Broadband Performance
20.3dB Gain at 2.14GHz
3.0dB Noise Figure at 2.14GHz with max gain setting
15.7dBm P1dB at 2.14GHz
28.5dBm OIP3 at 2.14GHz
No matching circuit needed
Attenuation: 0.5 dB steps to 31.5 dB
Safe attenuation state transitions
Monotonicity: 0.5 dB up to 4 GHz
High attenuation accuracy (DSA to Amp)
•
•
18
GND
17
GND
16
VDD
15
PUP2
14
PUP1
13
LE
12
CLOCK
C0.5
20
DATA
2
21
RF1
C1
22
GND
1
23
AMPIN
GND
24-lead 4x4 mm QFN
±(0.15 + 5% x Atten) @ 2.14GHz
24
GND
Preliminary Datasheet
The BVA303 integrates a high performance digital step attenuator
and a high linearity, broadband gain block.
using the small package(4x4mm QFN package) and operating VDD 3V
voltage.
and designed for use in 3G/4G wireless infrastructure and other high
performance RF applications.
●website: www.berex.com
1.8V control logic compatible
Programming modes
- Direct Parallel
- Latched Parallel
- Serial
Unique power-up state selection
•
Application
•
•
•
3G/4G Wireless infrastructure and other high performance RF application
Microwave and Satellite Radio
General purpose Wireless
●email: [email protected]
1
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Table 1. Electrical Specifications1
Parameter
Condition
Operational Frequency Range
Min
Typ
30
Gain2
Attenuation = 0dB, at 1900MHz
Attenuation Control range
0.5dB step
20.1
Attenuation Step
21.1
Preliminary Datasheet
Return loss
Unit
4000
MHz
22.1
dB
31.5
dB
0.5
dB
±(0.15 + 3% of atten setting)
30MHz — 1GHz
Attenuation
Accuracy
Max
±(0.15 + 5% of atten setting)
>1GHz — 2.2GHz
Any bit or bit combination
dB
>2.2GHz — 3GHz
±(0.15 + 8% of atten setting)
>3GHz — 4GHz
±(0.15 + 11% of atten setting)
1GHz — 2.2GHz
13
18
10
16
Attenuation = 0dB
(input or output
>2.2GHz — 4GHz
port)
Output Power for 1dB Compression
dB
Attenuation = 0dB , at 1900MHz
16
dBm
29
dBm
dB
Attenuation = 0dB, at 1900MHz
Output Third Order Intercept Point3
two tones at an output of 0 dBm per
tone separated by 1 MHz.
Noise Figure
Attenuation = 0dB, at 1900MHz
2.9
Switching time
50% CTRL to 90% or 10% RF
500
DSA
2.7
800
ns
5.5
V
Supply voltage
AMP
Supply Current
Control Interface
3
48
Serial / parallel mode
54
V
60
6
mA
Bit
Digital input high
1.17
3.6
V
Digital input low
-0.3
0.6
V
Control Voltage
Impedance
1
2
3
50
Ω
Device performance _ measured on a BeRex Evaluation board at 25°C, 50 Ω system, VDD=+3V, measure on Evaluation Board (DSA to AMP)
Gain data has PCB & Connectors insertion loss de-embedded
OIP3 _ measured with two tones at an output of 0 dBm per tone separated by 1 MHz.
BeRex
●website: www.berex.com
●email: [email protected]
2
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Table 2. Typical RF Performance1
Frequency
Parameter
70
Gain
3
S11
S22
Unit
900
1900
2140
2650
MHz
27.2
24.7
21.1
20.3
18.2
dB
-14.7
-13.7
-18.4
-18.2
-19.2
dB
-13.4
-10.7
-17
-16.4
-13.3
dB
4
31.5
31
29
28.5
27.2
dBm
P1dB
16.3
17
16
15.7
15
dBm
Noise Figure
2.4
2.8
2.9
3.0
3.2
dB
OIP3
Preliminary Datasheet
2
1
Device performance _ measured on a BeRex evaluation board at 25°C, VDD=+3V,50 Ω system. measure on Evaluation Board (DSA to AMP)
2
70MHz measured with application circuit refer to table 10
3
Gain data has PCB & Connectors insertion loss de-embedded
4
OIP3 _ measured with two tones at an output of 0 dBm per tone separated by 1 MHz.
Table 3. Absolute Maximum Ratings
Parameter
Condition
Supply Voltage(VDD)
Amp/DSA
Supply Current
Amp
Digital input voltage
Min
Typ
Amp/DSA
Operating Temperature
Amp/DSA
Storage Temperature
Unit
3.6/5.5
V
110
-0.3
Maximum input power
Max
mA
3.6
V
+12/+30
dBm
-40
85/105
℃
-55
150
℃
Junction Temperature
150
℃
Operation of this device above any of these parameters may result in permanent damage.
BeRex
●website: www.berex.com
●email: [email protected]
3
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
Parallel/Serial Selection
Either a parallel or serial interface can be used to control the BVA303.
The P/S bit provides this selection, with P/S = LOW selecting the parallel interface and P/S = HIGH selecting the serial interface.
Serial Interface
The serial interface is a 6-bit serial-in, parallel-out shift register buffered by a transparent latch. It is controlled by three CMOScompatible signals: Data, Clock, and Latch Enable (LE). The Data and
Clock inputs allow data to be serially entered into the shift register, a
process that is independent of the state of the LE input.
Parallel Mode Interface
The parallel interface consists of six CMOS compatible control lines
that select the desired attenuation state, as shown in Table 4.
The LE input controls the latch. When LE is HIGH, the latch is transparent and the contents of the serial shift register control the attenuator.
When LE is brought LOW, data in the shift register is latched.
The parallel interface timing requirements are defined by Figure 4
(Parallel Interface Timing Diagram), Table 7 (Parallel Interface AC
Characteristics), and switching speed (Table 1).
The shift register should be loaded while LE is held LOW to prevent
the attenuator value from changing as data is entered. The LE input
should then be toggled HIGH and brought LOW again, latching the
new data. The timing for this operation is defined by Figure 3 (Serial
Interface Timing Diagram) and Table 6 (Serial Interface AC Characteristics).
Programming Options
Preliminary Datasheet
30-4000 MHz
For latched parallel programming the Latch Enable (LE) should be held
LOW while changing attenuation state control values, then pulse LE
HIGH to LOW (per Figure 3) to latch the new attenuation state into
the device.
For direct parallel programming, the Latch Enable (LE) line should be
pulled HIGH. Changing attenuation state control values will change
device state to new attenuation. Direct Mode is ideal for manual
control of the device (using hardwire, switches, or jumpers).
Power-up Control Settings
The BVA303 always assumes a specifiable attenuation setting on
power-up. This feature exists for both the Serial and Parallel modes of
operation, and allows a known attenuation state to be established
before an initial serial or parallel control word is provided.
When the attenuator powers up in Serial mode (P/S = 1), the six control bits are set to whatever data is present on the six parallel data
inputs (C0.5 to C16). This allows any one of the 64 attenuation
settings to be specified as the power-up state.
When the attenuator powers up in Parallel mode (P/S = 0) with LE = 0,
the control bits are automatically set to one of four possible values.
These four values are selected by the two power-up control bits,
PUP1 and PUP2, as shown in Table 5
(Power-Up Truth Table, Parallel Mode).
Table 4. Truth Table
P/S
C16
C8
C4
C2
C1
C0.5 Attenuation state
0
0
0
0
0
0
0
Reference Loss
0
0
0
0
0
0
1
0.5 dB
0
0
0
0
0
1
0
1 dB
0
0
0
0
1
0
0
2 dB
0
0
0
1
0
0
0
4 dB
0
0
1
0
0
0
0
8 dB
0
1
0
0
0
0
0
16 dB
0
1
1
1
1
1
1
31.5 dB
Note: Not all 64 possible combinations of C0.5-C16 are shown in table
Table 5. Parallel PUP Truth Table
P/S
LE
PUP2
PUP1
Attenuation state
0
0
0
0
Reference Loss
0
0
1
0
8 dB
0
0
0
1
16 dB
0
0
1
1
31.5 dB
0
1
X
X
Defined by C0.5-C16
Note: Power up with LE = 1 provides normal parallel operation with C0.5-C16, and PUP1 and PUP2
are not active
BeRex
●website: www.berex.com
●email: [email protected]
4
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Figure 3. Serial Interface Timing Diagram
Table 8. 6-Bit Attenuator Serial Programming Register Map
B5
B4
B3
B3
B1
B0
C16
C8
C4
C2
C1
C0.5
MSB (first in)
LSB (Last in)
P/S
VSS/GND
20
19
C2
C4
C8
RF2
Figure 4. Parallel Interface Timing Diagram
24
23
22
21
GND
1
18
GND
C1
2
17
GND
C0.5
3
16
VDD
C16
4
15
PUP2
GND
5
14
PUP1
AMPOUT
6
13
LE
VDD = 3.3V with DSA only, -40°C < TA < 105°C, unless otherwise specified
Symbol
fClk
Parameter
Min Max
Serial data clock frequency
10
Unit
MHz
tClkH Serial clock HIGH time
30
ns
tClkL Serial clock LOW time
30
ns
LE set-up time after last
tLESUP
clock falling edge
10
ns
tLEPW LE minimum pulse width
30
ns
Serial data set-up time
tSDSUP
before clock rising edge
10
ns
10
ns
tSDHLD
Serial data hold time after
clock falling edge
Note: fClk is verified during the functional pattern test. Serial programming sections of the functional pattern
are clocked at 10 MHz to verify fclk specification
Table 7. Parallel Interface AC Characteristics
VDD = 3.3V with DSA only, -40°C < TA < 105°C, unless otherwise specified
Symbol
tLEPW
Parameter
Min Max
LE minimum pulse width
Data set-up time before
tPDSUP
rising edge of LE
Data hold time after falling
tPDHLD
edge of LE
BeRex
Unit
10
ns
10
ns
10
ns
●website: www.berex.com
11
12
Data
10
Clock
9
RF1
Table 6. Serial Interface AC Characteristics
8
GND
7
AMPIN
EXPOSED
Grounnd Pad
GND
Preliminary Datasheet
Figure 5. Pin Configuration(Top View)
Table 9. Pin Description
Pin
1,5,7,9,17,18
2
3
4
6
8
10
11
12
13
14
15
16
Pin name
GND
C1
C0.55
C163,5
AMPOUT
AMPIN
RF11
DATA3
Clock
LE4
PUP15
PUP2
VDD
19
VSS/GND2
20
21
22
23
24
P/S
RF21
C8
C4
C2
Description
Ground
Attenuation control bit, 1dB
Attenuation control bit, 0.5dB
Attenuation control bit, 16dB
RF Amp out Port
RF Amp in port
RF port(DSA output)
Serial interface data input
Serial interface clock input
Latch Enable input
Power-up selection bit 1
Power-up selection bit 2
Supply voltage (nominal 3V)
External VSS negative voltage control or
ground
Parallel/Serial mode select
RF port(DSA input)
Attenuation control bit, 8dB
Attenuation control bit, 4dB
Attenuation control bit, 2dB
Note: 1. RF pins 10 and 21 must be at 0V DC. The RF pins do not require DC blocking capacitors for proper
Operation if the 0V DC requirement is met
2. Use VssEXT (pin 19) to bypass and disable internal negative voltage generator.
Connect VssEXT (pin 19, VssEXT = GND) to enable internal negative voltage generator
3.Place a 10 kΩ resistor in series, as close to pin as possible to avoid frequency resonance
4. This pin has an internal 2 MΩ resistor to internal positive digital supply
5. This pin has an internal 200 kΩ resistor to GND
●email: [email protected]
5
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Typical Performance Plot - BVA303 EVK - PCB (Application Circuit : 500~4000MHz)
Typical Performance Data @ 25°C, Maximum gain state and VDD = 3.0V unless otherwise noted and Application Circuit refer to Table 10
Preliminary Datasheet
Figure 6. Gain1 vs Frequency
@ Temperature (Max Gain State)
Figure 7. Gain vs Frequency
@ Major Attenuation Steps
Note: 1. Gain data has PCB & Connectors insertion loss de-embedded
Figure 8. Input Return Loss vs Frequency
@ Temperature (Max Gain State)
Figure 9. Input Return Loss vs Frequency
@ Max Gain & Min Gain1 State
Note: 1. Min Gain was measured in the state is set with attenuation 31.5dB
Figure 10. output Return Loss vs. Frequency
@ Temperature (Max Gain State)
Figure 11. output Return Loss vs. Frequency
@ Max Gain & Min Gain1 State
Note: 1. Min Gain was measured in the state is set with attenuation 31.5dB
BeRex
●website: www.berex.com
●email: [email protected]
6
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Typical Performance Plot - BVA303 EVK - PCB (Application Circuit : 500~4000MHz)
Preliminary Datasheet
Typical Performance Data @ 25°C, Maximum gain state and VDD = 3.0V unless otherwise noted and Application Circuit refer to Table 10
Figure 12. OIP3 vs Frequency
@ Temperature (Max Gain State)
Figure 13. P1dB vs Frequency
@ Temperature (Max Gain State)
Figure 14. Noise Figure vs Frequency
@ Temperature (Max Gain State)
Figure 15. Attenuation Error vs Frequency
@ Major Attenuation Steps
Figure 16. Attenuation Error vs Attenuation Setting
@Major Frequency (Max Gain State)
Figure 17. 0.5dB Step Attenuation vs Attenuation Setting
@Major Frequency (Max Gain State)
BeRex
●website: www.berex.com
●email: [email protected]
7
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Typical Performance Plot - BVA303 EVK - PCB (Application Circuit : 500~4000MHz)
Preliminary Datasheet
Typical Performance Data @ 25°C, Maximum gain state and VDD = 3.0V unless otherwise noted and Application Circuit refer to Table 10
Figure 18. Attenuation Error @ 900MHz vs
Temperature
Figure 19. Attenuation Error @ 1.9GHz vs
Temperature
Figure 20. Attenuation Error @ 2.14GHz vs
Temperature
Figure 21. Attenuation Error @ 2.65GHz vs
Temperature
Figure 22. Attenuation Error @ 3.9GHz vs
Temperature
BeRex
●website: www.berex.com
●email: [email protected]
8
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Typical Performance Plot - BVA303 EVK - PCB (Application Circuit : 30~500MHz)
Typical Performance Data @ 25°C, Maximum gain state and VDD = 3.0V unless otherwise noted and Application Circuit refer to Table 10
Preliminary Datasheet
Figure 23. Gain1 vs Frequency
@ Temperature (Max Gain State)
Figure 24. Gain vs Frequency
@ Major Attenuation Steps
Note: 1. Gain data has PCB & Connectors insertion loss de-embedded
Figure 25. Input Return Loss vs Frequency
@ Temperature (Max Gain State)
Figure 26. Input Return Loss vs Frequency
@ Max Gain & Min Gain1 State
Note: 1. Min Gain was measured in the state is set with attenuation 31.5dB
Figure 27. output Return Loss vs. Frequency
@ Temperature (Max Gain State)
Figure 28. output Return Loss vs. Frequency
@ Max Gain & Min Gain1 State
Note: 1. Min Gain was measured in the state is set with attenuation 31.5dB
BeRex
●website: www.berex.com
●email: [email protected]
9
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Typical Performance Plot - BVA303 EVK - PCB (Application Circuit : 30~500MHz)
Preliminary Datasheet
Typical Performance Data @ 25°C, Maximum gain state and VDD = 3.0V unless otherwise noted and Application Circuit refer to Table 10
Figure 29. OIP3 vs Frequency
@ Temperature (Max Gain State)
Figure 30. P1dB vs Frequency
@ Temperature (Max Gain State)
Figure 31. Noise Figure vs Frequency
@ Temperature (Max Gain State)
Figure 32. Attenuation Error vs Frequency
@ Major Attenuation Steps
Figure 33. Attenuation Error vs Attenuation Setting
@Major Frequency (Max Gain State)
Figure 34. 0.5dB Step Attenuation vs Attenuation Setting
@Major Frequency (Max Gain State)
BeRex
●website: www.berex.com
●email: [email protected]
10
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Typical Performance Plot - BVA303 EVK - PCB (Application Circuit : 30~500MHz)
Preliminary Datasheet
Typical Performance Data @ 25°C, Maximum gain state and VDD = 3.0V unless otherwise noted and Application Circuit refer to Table 10
Figure 35. Attenuation Error @ 30MHz vs
Temperature
Figure 36. Attenuation Error @ 70MHz vs
Temperature
Figure 37. Attenuation Error @ 100MHz vs
Temperature
Figure 38. Attenuation Error @ 200MHz vs
Temperature
Figure 39. Attenuation Error @ 300MHz vs
Temperature
Figure 40. Attenuation Error @ 400MHz vs
Temperature
BeRex
●website: www.berex.com
●email: [email protected]
11
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Evaluation Board PCB Information
Figure 41. Evaluation Board PCB Layer Information
COPPER :1oz + 0.5oz (plating), Top Layer
EM825B ER: 4.6~4.8
P.P : (0.2+0.06+0.06) TOTAL = 0.32mm
COPPER :1oz (GND), Inner Layer
Preliminary Datasheet
MTC Er:4.6
CORE : 0.73mm
FINISH TICKNESS :1.55T
COPPER :1oz, Inner Layer
EM825B Er:4.6~4.8
P.P : (0.2+0.06+0.06) TOTAL = 0.32mm
COPPER :1oz + 0.5oz (plating), Bottom Layer
Figure 42. Evaluation Board PCB
BeRex
●website: www.berex.com
●email: [email protected]
12
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Preliminary Datasheet
Figure 43. Evaluation Board Schematic
Table 10. Application Circuit
Application Circuit Values Example
Freq.
C1/C3
L3(1005 Chip Ind)
IF Circuit
RF Circuit
50~500MHz 500MHz ~ 4GHz
2nF
100pF
820nH
12nH
Table 11. Bill of Material - Evaluation Board
No.
Ref Des
Part
Part Number
Qty
2 CAP 0402 100pF J 50V
1
C1,C3
2
C4,C15
2
3
C5
1
CAP 0402 1000pF J 50V
4
C6
1
TANTAL 3216 10UF 16V
5
C22
1
TANTAL 3216 0.1uF 35V
6
L3
1
IND 1608 12nH
7
R2,R3
2
RES 1005 J 10K
8
R1,R4,R6
3
9
CON1
1
10
U1
1
RES 1608 J 0ohm
15P-MALE-D-sub connector
QFN4X4_24L_BVA303
11
J1,J3
2
SMA_END_LAUNCH
REMARK
IF circuit refer to table 10
CAP 0402 100pF J 50V
IF circuit refer to table 10
Notice: Evaluation Board for Marketing Release was set to 500MHz to 4GHz application circuit
(Refer to Table 10)
BeRex
●website: www.berex.com
●email: [email protected]
13
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Preliminary Datasheet
Figure 44. Application Circuit schematic*
(Use only Serial mode)
* notice. The serial mode PUP state of this Figure 44. is setting in Reference Loss (Refer to Table 5.) and each combinations of C0.5-C16 are shown in the
Table 4. Truth Table.
BeRex
●website: www.berex.com
●email: [email protected]
14
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Preliminary Datasheet
Figure 45. Package Outline Dimension
Figure 46. Recommend Land Pattern
BeRex
●website: www.berex.com
●email: [email protected]
15
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5
BVA303
DIGITAL VARIABLE GAIN AMPLIFIER
30-4000 MHz
Preliminary Datasheet
Figure 47. Tape & Reel
Packaging information:
Figure 48. Package Marking
Marking information:
BVA303
YYWWXX
BVA303
Device Name
YY
Year
WW
Work Week
XX
LOT Number
Tape Width
Reel Size
Device Cavity Pitch
Devices Per Reel
12mm
7”
8mm
1K
Lead plating finish
100% Tin Matte finish
MSL / ESD Rating
ESD Rating:
Class 1C
Value:
Passes ≤ 2000V
Test:
Human Body Model(HBM)
Standard:
JEDEC Standard JESD22-A114B
MSL Rating:
Level 1 at +265°C convection reflow
Standard:
JEDEC Standard J-STD-020
C a u t i o n : ESD Sensitive
Appropriate precautions in handling, packaging
and testing devices must be observed.
Proper ESD procedures should be followed when handling this device.
NATO CAGE code:
2
BeRex
N
9
6
F
●website: www.berex.com
●email: [email protected]
16
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2018 BeRex
Rev. 0.5