Kingbright AA3528LSESK-J4 3.5x2.8mm surface mount led lamp Datasheet

3.5x2.8mm SURFACE MOUNT LED LAMP
Part Number: AA3528LSESK/J4
Super Bright Orange
Features
Description
z Single color.
The Orange source color devices are made with AlGaInP
z Suitable for all SMT assembly and solder process.
Light Emitting Diode.
z Available on tape and reel.
z Ideal for backlighting.
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z Low current IF=2mA operating.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN8370
REV NO: V.2A
DATE: MAR/09/2015
PAGE: 1 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1201008905
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAN8370
REV NO: V.2A
DATE: MAR/09/2015
PAGE: 2 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1201008905
Selection Guide
Part No.
Dice
Super Bright Orange (AlGaInP)
AA3528LSESK/J4
Iv (mcd) [2]
@ 2mA
Lens Type
Water Clear
Min.
Typ.
120
220
*30
*60
Viewing
Angle [1]
2θ1/2
120°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
*Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Units
Test Conditions
λpeak
Peak Wavelength
Super Bright Orange
611
nm
IF=2mA
λD [1]
Dominant Wavelength
Super Bright Orange
605
nm
IF=2mA
Δλ1/2
Spectral Line Half-width
Super Bright Orange
17
nm
IF=2mA
C
Capacitance
Super Bright Orange
27
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Super Bright Orange
2.1
V
IF=2mA
IR
Reverse Current
Super Bright Orange
10
uA
VR=5V
Min.
1.5
Typ.
1.8
Max.
Notes:
1.Wavelength: +/-1nm.
2.Forward Voltage: +/-0.1V.
3.Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Orange
Units
Power dissipation
105
mW
DC Forward Current
50
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAN8370
REV NO: V.2A
DATE: MAR/09/2015
PAGE: 3 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1201008905
Super Bright Orange
AA3528LSESK/J4
SPEC NO: DSAN8370
REV NO: V.2A
DATE: MAR/09/2015
PAGE: 4 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1201008905
AA3528LSESK/J4
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAN8370
REV NO: V.2A
DATE: MAR/09/2015
PAGE: 5 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1201008905
PACKING & LABEL SPECIFICATIONS
AA3528LSESK/J4
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAN8370
REV NO: V.2A
DATE: MAR/09/2015
PAGE: 6 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1201008905
Similar pages