TI1 LM4F110E5QR Tiva tm4c123be6pm microcontroller Datasheet

TE X AS I NS TRUM E NTS - P RO DUCTION D ATA
Tiva™ TM4C123BE6PM Microcontroller
D ATA SHE E T
D S -T M 4C 123BE 6 P M - 1 5 8 4 2 . 2 7 4 1
S P M S 365E
C o p yri g h t © 2 0 07-2014
Te xa s In stru me n ts In co rporated
Copyright
Copyright © 2007-2014 Texas Instruments Incorporated. Tiva and TivaWare are trademarks of Texas Instruments Incorporated. ARM and Thumb are
registered trademarks and Cortex is a trademark of ARM Limited. All other trademarks are the property of others.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard
warranty. Production processing does not necessarily include testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor
products and disclaimers thereto appears at the end of this data sheet.
Texas Instruments Incorporated
108 Wild Basin, Suite 350
Austin, TX 78746
http://www.ti.com/tm4c
http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm
2
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table of Contents
Revision History ............................................................................................................................. 34
About This Document .................................................................................................................... 38
Audience ..............................................................................................................................................
About This Manual ................................................................................................................................
Related Documents ...............................................................................................................................
Documentation Conventions ..................................................................................................................
38
38
38
39
1
Architectural Overview .......................................................................................... 41
1.1
1.2
1.3
1.3.1
1.3.2
1.3.3
1.3.4
1.3.5
1.3.6
1.3.7
1.3.8
1.4
1.5
1.6
Tiva™ C Series Overview .............................................................................................. 41
TM4C123BE6PM Microcontroller Overview .................................................................... 42
TM4C123BE6PM Microcontroller Features ..................................................................... 45
ARM Cortex-M4F Processor Core .................................................................................. 45
On-Chip Memory ........................................................................................................... 47
Serial Communications Peripherals ................................................................................ 49
System Integration ........................................................................................................ 52
Advanced Motion Control ............................................................................................... 58
Analog .......................................................................................................................... 61
JTAG and ARM Serial Wire Debug ................................................................................ 62
Packaging and Temperature .......................................................................................... 63
TM4C123BE6PM Microcontroller Hardware Details ......................................................... 63
Kits .............................................................................................................................. 63
Support Information ....................................................................................................... 63
2
The Cortex-M4F Processor ................................................................................... 64
2.1
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.4.7
2.5
2.5.1
Block Diagram .............................................................................................................. 65
Overview ...................................................................................................................... 66
System-Level Interface .................................................................................................. 66
Integrated Configurable Debug ...................................................................................... 66
Trace Port Interface Unit (TPIU) ..................................................................................... 67
Cortex-M4F System Component Details ......................................................................... 67
Programming Model ...................................................................................................... 68
Processor Mode and Privilege Levels for Software Execution ........................................... 68
Stacks .......................................................................................................................... 69
Register Map ................................................................................................................ 69
Register Descriptions .................................................................................................... 71
Exceptions and Interrupts .............................................................................................. 87
Data Types ................................................................................................................... 87
Memory Model .............................................................................................................. 87
Memory Regions, Types and Attributes ........................................................................... 90
Memory System Ordering of Memory Accesses .............................................................. 90
Behavior of Memory Accesses ....................................................................................... 90
Software Ordering of Memory Accesses ......................................................................... 91
Bit-Banding ................................................................................................................... 92
Data Storage ................................................................................................................ 94
Synchronization Primitives ............................................................................................. 95
Exception Model ........................................................................................................... 96
Exception States ........................................................................................................... 97
June 12, 2014
3
Texas Instruments-Production Data
Table of Contents
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
2.5.7
2.6
2.6.1
2.6.2
2.6.3
2.6.4
2.7
2.7.1
2.7.2
2.8
Exception Types ............................................................................................................ 97
Exception Handlers ..................................................................................................... 101
Vector Table ................................................................................................................ 101
Exception Priorities ...................................................................................................... 102
Interrupt Priority Grouping ............................................................................................ 103
Exception Entry and Return ......................................................................................... 103
Fault Handling ............................................................................................................. 106
Fault Types ................................................................................................................. 107
Fault Escalation and Hard Faults .................................................................................. 107
Fault Status Registers and Fault Address Registers ...................................................... 108
Lockup ....................................................................................................................... 108
Power Management .................................................................................................... 109
Entering Sleep Modes ................................................................................................. 109
Wake Up from Sleep Mode .......................................................................................... 109
Instruction Set Summary .............................................................................................. 110
3
Cortex-M4 Peripherals ......................................................................................... 117
3.1
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.2
3.3
3.4
3.5
3.6
3.7
Functional Description ................................................................................................. 117
System Timer (SysTick) ............................................................................................... 118
Nested Vectored Interrupt Controller (NVIC) .................................................................. 119
System Control Block (SCB) ........................................................................................ 120
Memory Protection Unit (MPU) ..................................................................................... 120
Floating-Point Unit (FPU) ............................................................................................. 125
Register Map .............................................................................................................. 129
System Timer (SysTick) Register Descriptions .............................................................. 132
NVIC Register Descriptions .......................................................................................... 136
System Control Block (SCB) Register Descriptions ........................................................ 151
Memory Protection Unit (MPU) Register Descriptions .................................................... 180
Floating-Point Unit (FPU) Register Descriptions ............................................................ 189
4
JTAG Interface ...................................................................................................... 195
4.1
4.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.4
4.5
4.5.1
4.5.2
Block Diagram ............................................................................................................
Signal Description .......................................................................................................
Functional Description .................................................................................................
JTAG Interface Pins .....................................................................................................
JTAG TAP Controller ...................................................................................................
Shift Registers ............................................................................................................
Operational Considerations ..........................................................................................
Initialization and Configuration .....................................................................................
Register Descriptions ..................................................................................................
Instruction Register (IR) ...............................................................................................
Data Registers ............................................................................................................
196
196
197
197
199
199
200
202
203
203
205
5
System Control ..................................................................................................... 207
5.1
5.2
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
Signal Description .......................................................................................................
Functional Description .................................................................................................
Device Identification ....................................................................................................
Reset Control ..............................................................................................................
Non-Maskable Interrupt ...............................................................................................
Power Control .............................................................................................................
Clock Control ..............................................................................................................
4
207
207
207
208
213
213
214
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
5.2.6
5.3
5.4
5.5
5.6
System Control ...........................................................................................................
Initialization and Configuration .....................................................................................
Register Map ..............................................................................................................
System Control Register Descriptions ...........................................................................
System Control Legacy Register Descriptions ...............................................................
221
225
226
231
412
6
System Exception Module ................................................................................... 473
6.1
6.2
6.3
Functional Description ................................................................................................. 473
Register Map .............................................................................................................. 473
Register Descriptions .................................................................................................. 473
7
Hibernation Module .............................................................................................. 481
7.1
7.2
7.3
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
7.3.7
7.3.8
7.3.9
7.3.10
7.3.11
7.3.12
7.4
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
7.5
7.6
Block Diagram ............................................................................................................
Signal Description .......................................................................................................
Functional Description .................................................................................................
Register Access Timing ...............................................................................................
Hibernation Clock Source ............................................................................................
System Implementation ...............................................................................................
Battery Management ...................................................................................................
Real-Time Clock ..........................................................................................................
Battery-Backed Memory ..............................................................................................
Power Control Using HIB .............................................................................................
Power Control Using VDD3ON Mode ...........................................................................
Initiating Hibernate ......................................................................................................
Waking from Hibernate ................................................................................................
Arbitrary Power Removal .............................................................................................
Interrupts and Status ...................................................................................................
Initialization and Configuration .....................................................................................
Initialization .................................................................................................................
RTC Match Functionality (No Hibernation) ....................................................................
RTC Match/Wake-Up from Hibernation .........................................................................
External Wake-Up from Hibernation ..............................................................................
RTC or External Wake-Up from Hibernation ..................................................................
Register Map ..............................................................................................................
Register Descriptions ..................................................................................................
482
482
483
483
484
485
486
487
489
489
489
489
489
490
490
491
491
492
492
492
493
493
494
8
Internal Memory ................................................................................................... 512
8.1
8.2
8.2.1
8.2.2
8.2.3
8.2.4
8.3
8.4
8.5
8.6
Block Diagram ............................................................................................................ 512
Functional Description ................................................................................................. 513
SRAM ........................................................................................................................ 513
ROM .......................................................................................................................... 514
Flash Memory ............................................................................................................. 516
EEPROM .................................................................................................................... 522
Register Map .............................................................................................................. 527
Flash Memory Register Descriptions (Flash Control Offset) ............................................ 529
EEPROM Register Descriptions (EEPROM Offset) ........................................................ 547
Memory Register Descriptions (System Control Offset) .................................................. 564
9
Micro Direct Memory Access (μDMA) ................................................................ 572
9.1
9.2
Block Diagram ............................................................................................................ 573
Functional Description ................................................................................................. 573
June 12, 2014
5
Texas Instruments-Production Data
Table of Contents
9.2.1
9.2.2
9.2.3
9.2.4
9.2.5
9.2.6
9.2.7
9.2.8
9.2.9
9.2.10
9.3
9.3.1
9.3.2
9.3.3
9.3.4
9.3.5
9.4
9.5
9.6
Channel Assignments .................................................................................................. 574
Priority ........................................................................................................................ 575
Arbitration Size ............................................................................................................ 575
Request Types ............................................................................................................ 575
Channel Configuration ................................................................................................. 576
Transfer Modes ........................................................................................................... 578
Transfer Size and Increment ........................................................................................ 586
Peripheral Interface ..................................................................................................... 586
Software Request ........................................................................................................ 586
Interrupts and Errors .................................................................................................... 587
Initialization and Configuration ..................................................................................... 587
Module Initialization ..................................................................................................... 587
Configuring a Memory-to-Memory Transfer ................................................................... 588
Configuring a Peripheral for Simple Transmit ................................................................ 589
Configuring a Peripheral for Ping-Pong Receive ............................................................ 591
Configuring Channel Assignments ................................................................................ 593
Register Map .............................................................................................................. 593
μDMA Channel Control Structure ................................................................................. 595
μDMA Register Descriptions ........................................................................................ 602
10
General-Purpose Input/Outputs (GPIOs) ........................................................... 636
10.1
10.2
10.2.1
10.2.2
10.2.3
10.2.4
10.2.5
10.2.6
10.3
10.4
10.5
Signal Description ....................................................................................................... 636
Functional Description ................................................................................................. 639
Data Control ............................................................................................................... 640
Interrupt Control .......................................................................................................... 641
Mode Control .............................................................................................................. 642
Commit Control ........................................................................................................... 643
Pad Control ................................................................................................................. 643
Identification ............................................................................................................... 643
Initialization and Configuration ..................................................................................... 643
Register Map .............................................................................................................. 645
Register Descriptions .................................................................................................. 648
11
General-Purpose Timers ...................................................................................... 691
11.1
11.2
11.3
11.3.1
11.3.2
11.3.3
11.3.4
11.3.5
11.3.6
11.3.7
11.4
11.4.1
11.4.2
11.4.3
11.4.4
11.4.5
Block Diagram ............................................................................................................ 692
Signal Description ....................................................................................................... 693
Functional Description ................................................................................................. 694
GPTM Reset Conditions .............................................................................................. 695
Timer Modes ............................................................................................................... 696
Wait-for-Trigger Mode .................................................................................................. 705
Synchronizing GP Timer Blocks ................................................................................... 706
DMA Operation ........................................................................................................... 707
Accessing Concatenated 16/32-Bit GPTM Register Values ............................................ 707
Accessing Concatenated 32/64-Bit Wide GPTM Register Values .................................... 707
Initialization and Configuration ..................................................................................... 709
One-Shot/Periodic Timer Mode .................................................................................... 709
Real-Time Clock (RTC) Mode ...................................................................................... 710
Input Edge-Count Mode ............................................................................................... 710
Input Edge Time Mode ................................................................................................. 711
PWM Mode ................................................................................................................. 711
6
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
11.5
11.6
Register Map .............................................................................................................. 712
Register Descriptions .................................................................................................. 713
12
Watchdog Timers ................................................................................................. 761
12.1
12.2
12.2.1
12.3
12.4
12.5
Block Diagram ............................................................................................................
Functional Description .................................................................................................
Register Access Timing ...............................................................................................
Initialization and Configuration .....................................................................................
Register Map ..............................................................................................................
Register Descriptions ..................................................................................................
762
762
763
763
763
764
13
Analog-to-Digital Converter (ADC) ..................................................................... 786
13.1
13.2
13.3
13.3.1
13.3.2
13.3.3
13.3.4
13.3.5
13.3.6
13.3.7
13.4
13.4.1
13.4.2
13.5
13.6
Block Diagram ............................................................................................................ 787
Signal Description ....................................................................................................... 788
Functional Description ................................................................................................. 789
Sample Sequencers .................................................................................................... 789
Module Control ............................................................................................................ 790
Hardware Sample Averaging Circuit ............................................................................. 793
Analog-to-Digital Converter .......................................................................................... 794
Differential Sampling ................................................................................................... 797
Internal Temperature Sensor ........................................................................................ 799
Digital Comparator Unit ............................................................................................... 800
Initialization and Configuration ..................................................................................... 804
Module Initialization ..................................................................................................... 804
Sample Sequencer Configuration ................................................................................. 805
Register Map .............................................................................................................. 805
Register Descriptions .................................................................................................. 807
14
Universal Asynchronous Receivers/Transmitters (UARTs) ............................. 880
14.1
Block Diagram ............................................................................................................
14.2
Signal Description .......................................................................................................
14.3
Functional Description .................................................................................................
14.3.1 Transmit/Receive Logic ...............................................................................................
14.3.2 Baud-Rate Generation .................................................................................................
14.3.3 Data Transmission ......................................................................................................
14.3.4 Serial IR (SIR) .............................................................................................................
14.3.5 ISO 7816 Support .......................................................................................................
14.3.6 Modem Handshake Support .........................................................................................
14.3.7 9-Bit UART Mode ........................................................................................................
14.3.8 FIFO Operation ...........................................................................................................
14.3.9 Interrupts ....................................................................................................................
14.3.10 Loopback Operation ....................................................................................................
14.3.11 DMA Operation ...........................................................................................................
14.4
Initialization and Configuration .....................................................................................
14.5
Register Map ..............................................................................................................
14.6
Register Descriptions ..................................................................................................
881
881
882
882
883
884
884
885
886
887
887
887
888
889
889
890
892
15
Synchronous Serial Interface (SSI) .................................................................... 939
15.1
15.2
15.3
Block Diagram ............................................................................................................ 940
Signal Description ....................................................................................................... 940
Functional Description ................................................................................................. 941
June 12, 2014
7
Texas Instruments-Production Data
Table of Contents
15.3.1
15.3.2
15.3.3
15.3.4
15.3.5
15.4
15.5
15.6
Bit Rate Generation .....................................................................................................
FIFO Operation ...........................................................................................................
Interrupts ....................................................................................................................
Frame Formats ...........................................................................................................
DMA Operation ...........................................................................................................
Initialization and Configuration .....................................................................................
Register Map ..............................................................................................................
Register Descriptions ..................................................................................................
941
942
942
943
951
952
954
955
16
Inter-Integrated Circuit (I2C) Interface ................................................................ 984
16.1
16.2
16.3
16.3.1
16.3.2
16.3.3
16.3.4
16.3.5
16.4
16.4.1
16.4.2
16.5
16.6
16.7
16.8
Block Diagram ............................................................................................................ 985
Signal Description ....................................................................................................... 985
Functional Description ................................................................................................. 986
I2C Bus Functional Overview ........................................................................................ 986
Available Speed Modes ............................................................................................... 990
Interrupts .................................................................................................................... 992
Loopback Operation .................................................................................................... 993
Command Sequence Flow Charts ................................................................................ 994
Initialization and Configuration .................................................................................... 1002
Configure the I2C Module to Transmit a Single Byte as a Master .................................. 1002
Configure the I2C Master to High Speed Mode ............................................................ 1003
Register Map ............................................................................................................ 1004
Register Descriptions (I2C Master) .............................................................................. 1005
Register Descriptions (I2C Slave) ............................................................................... 1022
Register Descriptions (I2C Status and Control) ............................................................ 1032
17
Controller Area Network (CAN) Module ........................................................... 1035
17.1
Block Diagram ........................................................................................................... 1036
17.2
Signal Description ..................................................................................................... 1036
17.3
Functional Description ............................................................................................... 1037
17.3.1 Initialization ............................................................................................................... 1038
17.3.2 Operation .................................................................................................................. 1038
17.3.3 Transmitting Message Objects ................................................................................... 1039
17.3.4 Configuring a Transmit Message Object ...................................................................... 1040
17.3.5 Updating a Transmit Message Object ......................................................................... 1041
17.3.6 Accepting Received Message Objects ........................................................................ 1041
17.3.7 Receiving a Data Frame ............................................................................................ 1042
17.3.8 Receiving a Remote Frame ........................................................................................ 1042
17.3.9 Receive/Transmit Priority ........................................................................................... 1043
17.3.10 Configuring a Receive Message Object ...................................................................... 1043
17.3.11 Handling of Received Message Objects ...................................................................... 1044
17.3.12 Handling of Interrupts ................................................................................................ 1046
17.3.13 Test Mode ................................................................................................................. 1047
17.3.14 Bit Timing Configuration Error Considerations ............................................................. 1049
17.3.15 Bit Time and Bit Rate ................................................................................................. 1049
17.3.16 Calculating the Bit Timing Parameters ........................................................................ 1051
17.4
Register Map ............................................................................................................ 1054
17.5
CAN Register Descriptions ......................................................................................... 1055
8
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
18
Analog Comparators .......................................................................................... 1086
18.1
18.2
18.3
18.3.1
18.4
18.5
18.6
Block Diagram ...........................................................................................................
Signal Description .....................................................................................................
Functional Description ...............................................................................................
Internal Reference Programming ................................................................................
Initialization and Configuration ....................................................................................
Register Map ............................................................................................................
Register Descriptions .................................................................................................
1087
1087
1088
1089
1091
1091
1092
19
Pulse Width Modulator (PWM) .......................................................................... 1101
19.1
19.2
19.3
19.3.1
19.3.2
19.3.3
19.3.4
19.3.5
19.3.6
19.3.7
19.3.8
19.3.9
19.4
19.5
19.6
Block Diagram ........................................................................................................... 1102
Signal Description ..................................................................................................... 1104
Functional Description ............................................................................................... 1105
Clock Configuration ................................................................................................... 1105
PWM Timer ............................................................................................................... 1105
PWM Comparators .................................................................................................... 1105
PWM Signal Generator .............................................................................................. 1106
Dead-Band Generator ............................................................................................... 1107
Interrupt/ADC-Trigger Selector ................................................................................... 1107
Synchronization Methods .......................................................................................... 1108
Fault Conditions ........................................................................................................ 1109
Output Control Block .................................................................................................. 1110
Initialization and Configuration .................................................................................... 1110
Register Map ............................................................................................................ 1111
Register Descriptions ................................................................................................. 1114
20
Quadrature Encoder Interface (QEI) ................................................................. 1176
20.1
20.2
20.3
20.4
20.5
20.6
Block Diagram ...........................................................................................................
Signal Description .....................................................................................................
Functional Description ...............................................................................................
Initialization and Configuration ....................................................................................
Register Map ............................................................................................................
Register Descriptions .................................................................................................
21
Pin Diagram ........................................................................................................ 1199
1176
1178
1179
1181
1181
1182
22
Signal Tables ...................................................................................................... 1200
22.1
22.2
22.3
22.4
22.5
22.6
Signals by Pin Number ..............................................................................................
Signals by Signal Name .............................................................................................
Signals by Function, Except for GPIO .........................................................................
GPIO Pins and Alternate Functions ............................................................................
Possible Pin Assignments for Alternate Functions .......................................................
Connections for Unused Signals .................................................................................
1201
1207
1214
1220
1222
1225
23
Electrical Characteristics .................................................................................. 1226
23.1
23.2
23.3
23.4
23.5
23.6
23.6.1
Maximum Ratings ......................................................................................................
Operating Characteristics ...........................................................................................
Recommended Operating Conditions .........................................................................
Load Conditions ........................................................................................................
JTAG and Boundary Scan ..........................................................................................
Power and Brown-Out ...............................................................................................
VDDA Levels ............................................................................................................
June 12, 2014
1226
1227
1228
1230
1231
1233
1233
9
Texas Instruments-Production Data
Table of Contents
23.6.2 VDD Levels ............................................................................................................... 1234
23.6.3 VDDC Levels ............................................................................................................ 1235
23.6.4 VDD Glitches ............................................................................................................ 1236
23.6.5 VDD Droop Response ............................................................................................... 1236
23.7
Reset ........................................................................................................................ 1238
23.8
On-Chip Low Drop-Out (LDO) Regulator ..................................................................... 1241
23.9
Clocks ...................................................................................................................... 1242
23.9.1 PLL Specifications ..................................................................................................... 1242
23.9.2 PIOSC Specifications ................................................................................................ 1243
23.9.3 Low-Frequency Internal Oscillator (LFIOSC) Specifications .......................................... 1243
23.9.4 Hibernation Clock Source Specifications ..................................................................... 1243
23.9.5 Main Oscillator Specifications ..................................................................................... 1244
23.9.6 System Clock Specification with ADC Operation .......................................................... 1248
23.10 Sleep Modes ............................................................................................................. 1249
23.11 Hibernation Module ................................................................................................... 1251
23.12 Flash Memory and EEPROM ..................................................................................... 1252
23.13 Input/Output Pin Characteristics ................................................................................. 1253
23.13.1 GPIO Module Characteristics ..................................................................................... 1253
23.13.2 Types of I/O Pins and ESD Protection ......................................................................... 1253
23.14 Analog-to-Digital Converter (ADC) .............................................................................. 1257
23.15 Synchronous Serial Interface (SSI) ............................................................................. 1260
23.16 Inter-Integrated Circuit (I2C) Interface ......................................................................... 1263
23.17 Analog Comparator ................................................................................................... 1264
23.18 Pulse-Width Modulator (PWM) ................................................................................... 1265
23.19 Current Consumption ................................................................................................. 1266
A
Package Information .......................................................................................... 1269
A.1
A.2
A.3
A.4
Orderable Devices .....................................................................................................
Device Nomenclature ................................................................................................
Device Markings ........................................................................................................
Packaging Diagram ...................................................................................................
10
1269
1269
1270
1271
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
List of Figures
Figure 1-1.
Figure 2-1.
Figure 2-2.
Figure 2-3.
Figure 2-4.
Figure 2-5.
Figure 2-6.
Figure 2-7.
Figure 3-1.
Figure 3-2.
Figure 4-1.
Figure 4-2.
Figure 4-3.
Figure 4-4.
Figure 4-5.
Figure 5-1.
Figure 5-2.
Figure 5-3.
Figure 5-4.
Figure 5-5.
Figure 5-6.
Figure 7-1.
Figure 7-2.
Figure 7-3.
Figure 7-4.
Figure 7-5.
Figure 7-6.
Figure 8-1.
Figure 8-2.
Figure 9-1.
Figure 9-2.
Figure 9-3.
Figure 9-4.
Figure 9-5.
Figure 9-6.
Figure 10-1.
Figure 10-2.
Figure 10-3.
Figure 10-4.
Figure 11-1.
Figure 11-2.
Figure 11-3.
Figure 11-4.
Figure 11-5.
Figure 11-6.
Tiva™ TM4C123BE6PM Microcontroller High-Level Block Diagram ......................... 44
CPU Block Diagram ............................................................................................. 66
TPIU Block Diagram ............................................................................................ 67
Cortex-M4F Register Set ...................................................................................... 70
Bit-Band Mapping ................................................................................................ 94
Data Storage ....................................................................................................... 95
Vector Table ...................................................................................................... 102
Exception Stack Frame ...................................................................................... 105
SRD Use Example ............................................................................................. 123
FPU Register Bank ............................................................................................ 126
JTAG Module Block Diagram .............................................................................. 196
Test Access Port State Machine ......................................................................... 199
IDCODE Register Format ................................................................................... 205
BYPASS Register Format ................................................................................... 205
Boundary Scan Register Format ......................................................................... 206
Basic RST Configuration .................................................................................... 210
External Circuitry to Extend Power-On Reset ....................................................... 210
Reset Circuit Controlled by Switch ...................................................................... 211
Power Architecture ............................................................................................ 214
Main Clock Tree ................................................................................................ 217
Module Clock Selection ...................................................................................... 223
Hibernation Module Block Diagram ..................................................................... 482
Using a Crystal as the Hibernation Clock Source with a Single Battery Source ...... 484
Using a Dedicated Oscillator as the Hibernation Clock Source with VDD3ON
Mode ................................................................................................................ 485
Using a Regulator for Both VDD and VBAT ............................................................ 486
Counter Behavior with a TRIM Value of 0x8002 ................................................... 488
Counter Behavior with a TRIM Value of 0x7FFC .................................................. 488
Internal Memory Block Diagram .......................................................................... 512
EEPROM Block Diagram ................................................................................... 513
μDMA Block Diagram ......................................................................................... 573
Example of Ping-Pong μDMA Transaction ........................................................... 579
Memory Scatter-Gather, Setup and Configuration ................................................ 581
Memory Scatter-Gather, μDMA Copy Sequence .................................................. 582
Peripheral Scatter-Gather, Setup and Configuration ............................................. 584
Peripheral Scatter-Gather, μDMA Copy Sequence ............................................... 585
Digital I/O Pads ................................................................................................. 639
Analog/Digital I/O Pads ...................................................................................... 640
GPIODATA Write Example ................................................................................. 641
GPIODATA Read Example ................................................................................. 641
GPTM Module Block Diagram ............................................................................ 692
Reading the RTC Value ...................................................................................... 699
Input Edge-Count Mode Example, Counting Down ............................................... 701
16-Bit Input Edge-Time Mode Example ............................................................... 702
16-Bit PWM Mode Example ................................................................................ 704
CCP Output, GPTMTnMATCHR > GPTMTnILR ................................................... 704
June 12, 2014
11
Texas Instruments-Production Data
Table of Contents
Figure 11-7.
Figure 11-8.
Figure 11-9.
Figure 12-1.
Figure 13-1.
Figure 13-2.
Figure 13-3.
Figure 13-4.
Figure 13-5.
Figure 13-6.
Figure 13-7.
Figure 13-8.
Figure 13-9.
Figure 13-10.
Figure 13-11.
Figure 13-12.
Figure 13-13.
Figure 13-14.
Figure 14-1.
Figure 14-2.
Figure 14-3.
Figure 15-1.
Figure 15-2.
Figure 15-3.
Figure 15-4.
Figure 15-5.
Figure 15-6.
Figure 15-7.
Figure 15-8.
Figure 15-9.
Figure 15-10.
Figure 15-11.
Figure 15-12.
Figure 16-1.
Figure 16-2.
Figure 16-3.
Figure 16-4.
Figure 16-5.
Figure 16-6.
Figure 16-7.
Figure 16-8.
Figure 16-9.
Figure 16-10.
Figure 16-11.
Figure 16-12.
Figure 16-13.
Figure 16-14.
Figure 16-15.
CCP Output, GPTMTnMATCHR = GPTMTnILR ................................................... 705
CCP Output, GPTMTnILR > GPTMTnMATCHR ................................................... 705
Timer Daisy Chain ............................................................................................. 706
WDT Module Block Diagram .............................................................................. 762
Implementation of Two ADC Blocks .................................................................... 787
ADC Module Block Diagram ............................................................................... 788
ADC Sample Phases ......................................................................................... 791
Doubling the ADC Sample Rate .......................................................................... 792
Skewed Sampling .............................................................................................. 792
Sample Averaging Example ............................................................................... 794
ADC Input Equivalency ...................................................................................... 795
ADC Voltage Reference ..................................................................................... 796
ADC Conversion Result ..................................................................................... 797
Differential Voltage Representation ..................................................................... 799
Internal Temperature Sensor Characteristic ......................................................... 800
Low-Band Operation (CIC=0x0 and/or CTC=0x0) ................................................ 802
Mid-Band Operation (CIC=0x1 and/or CTC=0x1) ................................................. 803
High-Band Operation (CIC=0x3 and/or CTC=0x3) ................................................ 804
UART Module Block Diagram ............................................................................. 881
UART Character Frame ..................................................................................... 883
IrDA Data Modulation ......................................................................................... 885
SSI Module Block Diagram ................................................................................. 940
TI Synchronous Serial Frame Format (Single Transfer) ........................................ 944
TI Synchronous Serial Frame Format (Continuous Transfer) ................................ 945
Freescale SPI Format (Single Transfer) with SPO=0 and SPH=0 .......................... 946
Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0 .................. 946
Freescale SPI Frame Format with SPO=0 and SPH=1 ......................................... 947
Freescale SPI Frame Format (Single Transfer) with SPO=1 and SPH=0 ............... 948
Freescale SPI Frame Format (Continuous Transfer) with SPO=1 and SPH=0 ........ 948
Freescale SPI Frame Format with SPO=1 and SPH=1 ......................................... 949
MICROWIRE Frame Format (Single Frame) ........................................................ 950
MICROWIRE Frame Format (Continuous Transfer) ............................................. 951
MICROWIRE Frame Format, SSInFss Input Setup and Hold Requirements .......... 951
I2C Block Diagram ............................................................................................. 985
I2C Bus Configuration ........................................................................................ 986
START and STOP Conditions ............................................................................. 986
Complete Data Transfer with a 7-Bit Address ....................................................... 987
R/S Bit in First Byte ............................................................................................ 987
Data Validity During Bit Transfer on the I2C Bus ................................................... 988
High-Speed Data Format ................................................................................... 992
Master Single TRANSMIT .................................................................................. 995
Master Single RECEIVE ..................................................................................... 996
Master TRANSMIT of Multiple Data Bytes ........................................................... 997
Master RECEIVE of Multiple Data Bytes ............................................................. 998
Master RECEIVE with Repeated START after Master TRANSMIT ........................ 999
Master TRANSMIT with Repeated START after Master RECEIVE ....................... 1000
Standard High Speed Mode Master Transmit ..................................................... 1001
Slave Command Sequence .............................................................................. 1002
12
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Figure 17-1.
Figure 17-2.
Figure 17-3.
Figure 17-4.
Figure 18-1.
Figure 18-2.
Figure 18-3.
Figure 19-1.
Figure 19-2.
Figure 19-3.
Figure 19-4.
Figure 19-5.
Figure 19-6.
Figure 20-1.
Figure 20-2.
Figure 20-3.
Figure 21-1.
Figure 23-1.
Figure 23-2.
Figure 23-3.
Figure 23-4.
Figure 23-5.
Figure 23-6.
Figure 23-7.
Figure 23-8.
Figure 23-9.
Figure 23-10.
Figure 23-11.
Figure 23-12.
Figure 23-13.
Figure 23-14.
Figure 23-15.
Figure 23-16.
Figure 23-17.
Figure 23-18.
Figure 23-19.
Figure 23-20.
Figure 23-21.
Figure 23-22.
Figure 23-23.
Figure A-1.
Figure A-2.
CAN Controller Block Diagram .......................................................................... 1036
CAN Data/Remote Frame ................................................................................. 1037
Message Objects in a FIFO Buffer .................................................................... 1046
CAN Bit Time ................................................................................................... 1050
Analog Comparator Module Block Diagram ....................................................... 1087
Structure of Comparator Unit ............................................................................ 1088
Comparator Internal Reference Structure .......................................................... 1089
PWM Module Diagram ..................................................................................... 1103
PWM Generator Block Diagram ........................................................................ 1103
PWM Count-Down Mode .................................................................................. 1106
PWM Count-Up/Down Mode ............................................................................. 1106
PWM Generation Example In Count-Up/Down Mode .......................................... 1107
PWM Dead-Band Generator ............................................................................. 1107
QEI Block Diagram .......................................................................................... 1177
QEI Input Signal Logic ...................................................................................... 1178
Quadrature Encoder and Velocity Predivider Operation ...................................... 1180
64-Pin LQFP Package Pin Diagram .................................................................. 1199
Load Conditions ............................................................................................... 1230
JTAG Test Clock Input Timing ........................................................................... 1231
JTAG Test Access Port (TAP) Timing ................................................................ 1232
Power Assertions versus VDDA Levels ............................................................. 1234
Power and Brown-Out Assertions versus VDD Levels ........................................ 1235
POK assertion vs VDDC ................................................................................... 1236
POR-BOR0-BOR1 VDD Glitch Response .......................................................... 1236
POR-BOR0-BOR1 VDD Droop Response ......................................................... 1237
Digital Power-On Reset Timing ......................................................................... 1238
Brown-Out Reset Timing .................................................................................. 1239
External Reset Timing (RST) ............................................................................ 1239
Software Reset Timing ..................................................................................... 1239
Watchdog Reset Timing ................................................................................... 1239
MOSC Failure Reset Timing ............................................................................. 1240
Hibernation Module Timing ............................................................................... 1251
ESD Protection on Fail-Safe Pins ...................................................................... 1254
ESD Protection on Non-Fail-Safe Pins .............................................................. 1255
ADC Input Equivalency Diagram ....................................................................... 1259
SSI Timing for TI Frame Format (FRF=01), Single Transfer Timing
Measurement .................................................................................................. 1261
SSI Timing for MICROWIRE Frame Format (FRF=10), Single Transfer ............... 1261
Master Mode SSI Timing for SPI Frame Format (FRF=00), with SPH=1 .............. 1262
Slave Mode SSI Timing for SPI Frame Format (FRF=00), with SPH=1 ................ 1262
I2C Timing ....................................................................................................... 1263
Key to Part Numbers ........................................................................................ 1269
TM4C123BE6PM 64-Pin LQFP Package Diagram ............................................. 1271
June 12, 2014
13
Texas Instruments-Production Data
Table of Contents
List of Tables
Table 1.
Table 2.
Table 1-1.
Table 2-1.
Table 2-2.
Table 2-3.
Table 2-4.
Table 2-5.
Table 2-6.
Table 2-7.
Table 2-8.
Table 2-9.
Table 2-10.
Table 2-11.
Table 2-12.
Table 2-13.
Table 3-1.
Table 3-2.
Table 3-3.
Table 3-4.
Table 3-5.
Table 3-6.
Table 3-7.
Table 3-8.
Table 3-9.
Table 3-10.
Table 4-1.
Table 4-2.
Table 4-3.
Table 5-1.
Table 5-2.
Table 5-3.
Table 5-4.
Table 5-5.
Table 5-6.
Table 5-7.
Table 5-8.
Table 6-1.
Table 7-1.
Table 7-2.
Table 7-3.
Table 8-1.
Table 8-2.
Table 8-3.
Table 9-1.
Table 9-2.
Revision History .................................................................................................. 34
Documentation Conventions ................................................................................ 39
TM4C123BE6PM Microcontroller Features ............................................................ 42
Summary of Processor Mode, Privilege Level, and Stack Use ................................ 69
Processor Register Map ....................................................................................... 70
PSR Register Combinations ................................................................................. 76
Memory Map ....................................................................................................... 87
Memory Access Behavior ..................................................................................... 90
SRAM Memory Bit-Banding Regions .................................................................... 92
Peripheral Memory Bit-Banding Regions ............................................................... 93
Exception Types .................................................................................................. 98
Interrupts ............................................................................................................ 99
Exception Return Behavior ................................................................................. 106
Faults ............................................................................................................... 107
Fault Status and Fault Address Registers ............................................................ 108
Cortex-M4F Instruction Summary ....................................................................... 110
Core Peripheral Register Regions ....................................................................... 117
Memory Attributes Summary .............................................................................. 121
TEX, S, C, and B Bit Field Encoding ................................................................... 123
Cache Policy for Memory Attribute Encoding ....................................................... 124
AP Bit Field Encoding ........................................................................................ 124
Memory Region Attributes for Tiva™ C Series Microcontrollers ............................. 125
QNaN and SNaN Handling ................................................................................. 128
Peripherals Register Map ................................................................................... 129
Interrupt Priority Levels ...................................................................................... 159
Example SIZE Field Values ................................................................................ 187
JTAG_SWD_SWO Signals (64LQFP) ................................................................. 196
JTAG Port Pins State after Power-On Reset or RST assertion .............................. 197
JTAG Instruction Register Commands ................................................................. 203
System Control & Clocks Signals (64LQFP) ........................................................ 207
Reset Sources ................................................................................................... 208
Clock Source Options ........................................................................................ 215
Possible System Clock Frequencies Using the SYSDIV Field ............................... 218
Examples of Possible System Clock Frequencies Using the SYSDIV2 Field .......... 218
Examples of Possible System Clock Frequencies with DIV400=1 ......................... 219
System Control Register Map ............................................................................. 226
RCC2 Fields that Override RCC Fields ............................................................... 253
System Exception Register Map ......................................................................... 473
Hibernate Signals (64LQFP) ............................................................................... 482
Hibernation Module Clock Operation ................................................................... 491
Hibernation Module Register Map ....................................................................... 493
Flash Memory Protection Policy Combinations .................................................... 517
User-Programmable Flash Memory Resident Registers ....................................... 521
Flash Register Map ............................................................................................ 528
μDMA Channel Assignments .............................................................................. 574
Request Type Support ....................................................................................... 576
14
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 9-3.
Table 9-4.
Table 9-5.
Table 9-6.
Table 9-7.
Table 9-8.
Table 9-9.
Table 9-10.
Table 9-11.
Table 9-12.
Control Structure Memory Map ........................................................................... 577
Channel Control Structure .................................................................................. 577
μDMA Read Example: 8-Bit Peripheral ................................................................ 586
μDMA Interrupt Assignments .............................................................................. 587
Channel Control Structure Offsets for Channel 30 ................................................ 588
Channel Control Word Configuration for Memory Transfer Example ...................... 589
Channel Control Structure Offsets for Channel 7 .................................................. 590
Channel Control Word Configuration for Peripheral Transmit Example .................. 590
Primary and Alternate Channel Control Structure Offsets for Channel 8 ................. 591
Channel Control Word Configuration for Peripheral Ping-Pong Receive
Example ............................................................................................................ 592
Table 9-13.
μDMA Register Map .......................................................................................... 594
Table 10-1.
GPIO Pins With Special Considerations .............................................................. 637
Table 10-2.
GPIO Pins and Alternate Functions (64LQFP) ..................................................... 637
Table 10-3.
GPIO Pad Configuration Examples ..................................................................... 644
Table 10-4.
GPIO Interrupt Configuration Example ................................................................ 645
Table 10-5.
GPIO Pins With Special Considerations .............................................................. 646
Table 10-6.
GPIO Register Map ........................................................................................... 647
Table 10-7.
GPIO Pins With Special Considerations .............................................................. 658
Table 10-8.
GPIO Pins With Special Considerations .............................................................. 664
Table 10-9.
GPIO Pins With Special Considerations .............................................................. 666
Table 10-10. GPIO Pins With Special Considerations .............................................................. 669
Table 10-11. GPIO Pins With Special Considerations .............................................................. 675
Table 11-1.
Available CCP Pins ............................................................................................ 693
Table 11-2.
General-Purpose Timers Signals (64LQFP) ......................................................... 693
Table 11-3.
General-Purpose Timer Capabilities .................................................................... 695
Table 11-4.
Counter Values When the Timer is Enabled in Periodic or One-Shot Modes .......... 696
Table 11-5.
16-Bit Timer With Prescaler Configurations ......................................................... 697
Table 11-6.
32-Bit Timer (configured in 32/64-bit mode) With Prescaler Configurations ............ 698
Table 11-7.
Counter Values When the Timer is Enabled in RTC Mode .................................... 698
Table 11-8.
Counter Values When the Timer is Enabled in Input Edge-Count Mode ................. 700
Table 11-9.
Counter Values When the Timer is Enabled in Input Event-Count Mode ................ 701
Table 11-10. Counter Values When the Timer is Enabled in PWM Mode ................................... 703
Table 11-11. Timeout Actions for GPTM Modes ...................................................................... 706
Table 11-12. Timers Register Map .......................................................................................... 713
Table 12-1.
Watchdog Timers Register Map .......................................................................... 764
Table 13-1.
ADC Signals (64LQFP) ...................................................................................... 788
Table 13-2.
Samples and FIFO Depth of Sequencers ............................................................ 789
Table 13-3.
Differential Sampling Pairs ................................................................................. 797
Table 13-4.
ADC Register Map ............................................................................................. 805
Table 14-1.
UART Signals (64LQFP) .................................................................................... 882
Table 14-2.
Flow Control Mode ............................................................................................. 886
Table 14-3.
UART Register Map ........................................................................................... 891
Table 15-1.
SSI Signals (64LQFP) ........................................................................................ 941
Table 15-2.
SSI Register Map .............................................................................................. 954
Table 16-1.
I2C Signals (64LQFP) ........................................................................................ 985
Table 16-2.
Examples of I2C Master Timer Period Versus Speed Mode ................................... 991
Table 16-3.
Examples of I2C Master Timer Period in High-Speed Mode .................................. 992
June 12, 2014
15
Texas Instruments-Production Data
Table of Contents
Table 16-4.
Table 16-5.
Table 17-1.
Table 17-2.
Table 17-3.
Table 17-4.
Table 17-5.
Table 18-1.
Table 18-2.
Table 18-3.
Table 18-4.
Table 18-5.
Table 19-1.
Table 19-2.
Table 20-1.
Table 20-2.
Table 22-1.
Table 22-2.
Table 22-3.
Table 22-4.
Table 22-5.
Table 22-6.
Table 22-7.
Table 23-1.
Table 23-2.
Table 23-3.
Table 23-4.
Table 23-5.
Table 23-6.
Table 23-7.
Table 23-8.
Table 23-9.
Table 23-10.
Table 23-11.
Table 23-12.
Table 23-13.
Table 23-14.
Table 23-15.
Table 23-16.
Table 23-17.
Table 23-18.
Table 23-19.
Table 23-20.
Table 23-21.
Table 23-22.
Table 23-23.
Inter-Integrated Circuit (I2C) Interface Register Map ........................................... 1004
Write Field Decoding for I2CMCS[3:0] Field ....................................................... 1010
Controller Area Network Signals (64LQFP) ........................................................ 1037
Message Object Configurations ........................................................................ 1042
CAN Protocol Ranges ...................................................................................... 1050
CANBIT Register Values .................................................................................. 1050
CAN Register Map ........................................................................................... 1054
Analog Comparators Signals (64LQFP) ............................................................. 1087
Internal Reference Voltage and ACREFCTL Field Values ................................... 1089
Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 0 .......................................................................................................... 1090
Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 1 .......................................................................................................... 1090
Analog Comparators Register Map ................................................................... 1091
PWM Signals (64LQFP) ................................................................................... 1104
PWM Register Map .......................................................................................... 1111
QEI Signals (64LQFP) ...................................................................................... 1178
QEI Register Map ............................................................................................ 1182
GPIO Pins With Special Considerations ............................................................ 1200
Signals by Pin Number ..................................................................................... 1201
Signals by Signal Name ................................................................................... 1207
Signals by Function, Except for GPIO ............................................................... 1214
GPIO Pins and Alternate Functions ................................................................... 1220
Possible Pin Assignments for Alternate Functions .............................................. 1222
Connections for Unused Signals (64-Pin LQFP) ................................................. 1225
Absolute Maximum Ratings .............................................................................. 1226
ESD Absolute Maximum Ratings ...................................................................... 1226
Temperature Characteristics ............................................................................. 1227
Thermal Characteristics ................................................................................... 1227
Recommended DC Operating Conditions .......................................................... 1228
Recommended GPIO Pad Operating Conditions ................................................ 1228
GPIO Current Restrictions ................................................................................ 1228
GPIO Package Side Assignments ..................................................................... 1229
JTAG Characteristics ....................................................................................... 1231
Power-On and Brown-Out Levels ...................................................................... 1233
Reset Characteristics ....................................................................................... 1238
LDO Regulator Characteristics ......................................................................... 1241
Phase Locked Loop (PLL) Characteristics ......................................................... 1242
Actual PLL Frequency ...................................................................................... 1242
PIOSC Clock Characteristics ............................................................................ 1243
Low-Frequency internal Oscillator Characteristics .............................................. 1243
Hibernation Oscillator Input Characteristics ........................................................ 1243
Main Oscillator Input Characteristics ................................................................. 1244
Crystal Parameters .......................................................................................... 1246
Supported MOSC Crystal Frequencies .............................................................. 1247
System Clock Characteristics with ADC Operation ............................................. 1248
Sleep Modes AC Characteristics ....................................................................... 1249
Time to Wake with Respect to Low-Power Modes .............................................. 1249
16
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 23-24.
Table 23-25.
Table 23-26.
Table 23-27.
Table 23-28.
Table 23-29.
Table 23-30.
Table 23-31.
Table 23-32.
Table 23-33.
Table 23-34.
Table 23-35.
Table 23-36.
Table 23-37.
Hibernation Module Battery Characteristics ....................................................... 1251
Hibernation Module AC Characteristics ............................................................. 1251
Flash Memory Characteristics ........................................................................... 1252
EEPROM Characteristics ................................................................................. 1252
GPIO Module Characteristics ............................................................................ 1253
Pad Voltage/Current Characteristics for Fail-Safe Pins ....................................... 1254
Fail-Safe GPIOs that Require an External Pull-up .............................................. 1255
Non-Fail-Safe I/O Pad Voltage/Current Characteristics ....................................... 1255
ADC Electrical Characteristics .......................................................................... 1257
SSI Characteristics .......................................................................................... 1260
I2C Characteristics ........................................................................................... 1263
Analog Comparator Characteristics ................................................................... 1264
Analog Comparator Voltage Reference Characteristics ...................................... 1264
Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 0 .......................................................................................................... 1264
Table 23-38. Analog Comparator Voltage Reference Characteristics, VDDA = 3.3V, EN= 1, and
RNG = 1 .......................................................................................................... 1265
Table 23-39. PWM Timing Characteristics ............................................................................. 1265
Table 23-40. Current Consumption ....................................................................................... 1266
June 12, 2014
17
Texas Instruments-Production Data
Table of Contents
List of Registers
The Cortex-M4F Processor ........................................................................................................... 64
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Cortex General-Purpose Register 0 (R0) ........................................................................... 72
Cortex General-Purpose Register 1 (R1) ........................................................................... 72
Cortex General-Purpose Register 2 (R2) ........................................................................... 72
Cortex General-Purpose Register 3 (R3) ........................................................................... 72
Cortex General-Purpose Register 4 (R4) ........................................................................... 72
Cortex General-Purpose Register 5 (R5) ........................................................................... 72
Cortex General-Purpose Register 6 (R6) ........................................................................... 72
Cortex General-Purpose Register 7 (R7) ........................................................................... 72
Cortex General-Purpose Register 8 (R8) ........................................................................... 72
Cortex General-Purpose Register 9 (R9) ........................................................................... 72
Cortex General-Purpose Register 10 (R10) ....................................................................... 72
Cortex General-Purpose Register 11 (R11) ........................................................................ 72
Cortex General-Purpose Register 12 (R12) ....................................................................... 72
Stack Pointer (SP) ........................................................................................................... 73
Link Register (LR) ............................................................................................................ 74
Program Counter (PC) ..................................................................................................... 75
Program Status Register (PSR) ........................................................................................ 76
Priority Mask Register (PRIMASK) .................................................................................... 80
Fault Mask Register (FAULTMASK) .................................................................................. 81
Base Priority Mask Register (BASEPRI) ............................................................................ 82
Control Register (CONTROL) ........................................................................................... 83
Floating-Point Status Control (FPSC) ................................................................................ 85
Cortex-M4 Peripherals ................................................................................................................. 117
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
SysTick Control and Status Register (STCTRL), offset 0x010 ........................................... 133
SysTick Reload Value Register (STRELOAD), offset 0x014 .............................................. 135
SysTick Current Value Register (STCURRENT), offset 0x018 ........................................... 136
Interrupt 0-31 Set Enable (EN0), offset 0x100 .................................................................. 137
Interrupt 32-63 Set Enable (EN1), offset 0x104 ................................................................ 137
Interrupt 64-95 Set Enable (EN2), offset 0x108 ................................................................ 137
Interrupt 96-127 Set Enable (EN3), offset 0x10C ............................................................. 137
Interrupt 128-138 Set Enable (EN4), offset 0x110 ............................................................ 138
Interrupt 0-31 Clear Enable (DIS0), offset 0x180 .............................................................. 139
Interrupt 32-63 Clear Enable (DIS1), offset 0x184 ............................................................ 139
Interrupt 64-95 Clear Enable (DIS2), offset 0x188 ............................................................ 139
Interrupt 96-127 Clear Enable (DIS3), offset 0x18C .......................................................... 139
Interrupt 128-138 Clear Enable (DIS4), offset 0x190 ........................................................ 140
Interrupt 0-31 Set Pending (PEND0), offset 0x200 ........................................................... 141
Interrupt 32-63 Set Pending (PEND1), offset 0x204 ......................................................... 141
Interrupt 64-95 Set Pending (PEND2), offset 0x208 ......................................................... 141
Interrupt 96-127 Set Pending (PEND3), offset 0x20C ....................................................... 141
Interrupt 128-138 Set Pending (PEND4), offset 0x210 ...................................................... 142
Interrupt 0-31 Clear Pending (UNPEND0), offset 0x280 ................................................... 143
Interrupt 32-63 Clear Pending (UNPEND1), offset 0x284 .................................................. 143
Interrupt 64-95 Clear Pending (UNPEND2), offset 0x288 .................................................. 143
18
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
Register 59:
Register 60:
Register 61:
Register 62:
Register 63:
Register 64:
Register 65:
Register 66:
Register 67:
Register 68:
Register 69:
Interrupt 96-127 Clear Pending (UNPEND3), offset 0x28C ............................................... 143
Interrupt 128-138 Clear Pending (UNPEND4), offset 0x290 .............................................. 144
Interrupt 0-31 Active Bit (ACTIVE0), offset 0x300 ............................................................. 145
Interrupt 32-63 Active Bit (ACTIVE1), offset 0x304 ........................................................... 145
Interrupt 64-95 Active Bit (ACTIVE2), offset 0x308 ........................................................... 145
Interrupt 96-127 Active Bit (ACTIVE3), offset 0x30C ........................................................ 145
Interrupt 128-138 Active Bit (ACTIVE4), offset 0x310 ....................................................... 146
Interrupt 0-3 Priority (PRI0), offset 0x400 ......................................................................... 147
Interrupt 4-7 Priority (PRI1), offset 0x404 ......................................................................... 147
Interrupt 8-11 Priority (PRI2), offset 0x408 ....................................................................... 147
Interrupt 12-15 Priority (PRI3), offset 0x40C .................................................................... 147
Interrupt 16-19 Priority (PRI4), offset 0x410 ..................................................................... 147
Interrupt 20-23 Priority (PRI5), offset 0x414 ..................................................................... 147
Interrupt 24-27 Priority (PRI6), offset 0x418 ..................................................................... 147
Interrupt 28-31 Priority (PRI7), offset 0x41C .................................................................... 147
Interrupt 32-35 Priority (PRI8), offset 0x420 ..................................................................... 147
Interrupt 36-39 Priority (PRI9), offset 0x424 ..................................................................... 147
Interrupt 40-43 Priority (PRI10), offset 0x428 ................................................................... 147
Interrupt 44-47 Priority (PRI11), offset 0x42C ................................................................... 147
Interrupt 48-51 Priority (PRI12), offset 0x430 ................................................................... 147
Interrupt 52-55 Priority (PRI13), offset 0x434 ................................................................... 147
Interrupt 56-59 Priority (PRI14), offset 0x438 ................................................................... 147
Interrupt 60-63 Priority (PRI15), offset 0x43C .................................................................. 147
Interrupt 64-67 Priority (PRI16), offset 0x440 ................................................................... 149
Interrupt 68-71 Priority (PRI17), offset 0x444 ................................................................... 149
Interrupt 72-75 Priority (PRI18), offset 0x448 ................................................................... 149
Interrupt 76-79 Priority (PRI19), offset 0x44C .................................................................. 149
Interrupt 80-83 Priority (PRI20), offset 0x450 ................................................................... 149
Interrupt 84-87 Priority (PRI21), offset 0x454 ................................................................... 149
Interrupt 88-91 Priority (PRI22), offset 0x458 ................................................................... 149
Interrupt 92-95 Priority (PRI23), offset 0x45C .................................................................. 149
Interrupt 96-99 Priority (PRI24), offset 0x460 ................................................................... 149
Interrupt 100-103 Priority (PRI25), offset 0x464 ............................................................... 149
Interrupt 104-107 Priority (PRI26), offset 0x468 ............................................................... 149
Interrupt 108-111 Priority (PRI27), offset 0x46C ............................................................... 149
Interrupt 112-115 Priority (PRI28), offset 0x470 ................................................................ 149
Interrupt 116-119 Priority (PRI29), offset 0x474 ................................................................ 149
Interrupt 120-123 Priority (PRI30), offset 0x478 ............................................................... 149
Interrupt 124-127 Priority (PRI31), offset 0x47C ............................................................... 149
Interrupt 128-131 Priority (PRI32), offset 0x480 ............................................................... 149
Interrupt 132-135 Priority (PRI33), offset 0x484 ............................................................... 149
Interrupt 136-138 Priority (PRI34), offset 0x488 ............................................................... 149
Software Trigger Interrupt (SWTRIG), offset 0xF00 .......................................................... 151
Auxiliary Control (ACTLR), offset 0x008 .......................................................................... 152
CPU ID Base (CPUID), offset 0xD00 ............................................................................... 154
Interrupt Control and State (INTCTRL), offset 0xD04 ........................................................ 155
Vector Table Offset (VTABLE), offset 0xD08 .................................................................... 158
Application Interrupt and Reset Control (APINT), offset 0xD0C ......................................... 159
June 12, 2014
19
Texas Instruments-Production Data
Table of Contents
Register 70:
Register 71:
Register 72:
Register 73:
Register 74:
Register 75:
Register 76:
Register 77:
Register 78:
Register 79:
Register 80:
Register 81:
Register 82:
Register 83:
Register 84:
Register 85:
Register 86:
Register 87:
Register 88:
Register 89:
Register 90:
Register 91:
Register 92:
Register 93:
Register 94:
System Control (SYSCTRL), offset 0xD10 ....................................................................... 161
Configuration and Control (CFGCTRL), offset 0xD14 ....................................................... 163
System Handler Priority 1 (SYSPRI1), offset 0xD18 ......................................................... 165
System Handler Priority 2 (SYSPRI2), offset 0xD1C ........................................................ 166
System Handler Priority 3 (SYSPRI3), offset 0xD20 ......................................................... 167
System Handler Control and State (SYSHNDCTRL), offset 0xD24 .................................... 168
Configurable Fault Status (FAULTSTAT), offset 0xD28 ..................................................... 172
Hard Fault Status (HFAULTSTAT), offset 0xD2C .............................................................. 178
Memory Management Fault Address (MMADDR), offset 0xD34 ........................................ 179
Bus Fault Address (FAULTADDR), offset 0xD38 .............................................................. 180
MPU Type (MPUTYPE), offset 0xD90 ............................................................................. 181
MPU Control (MPUCTRL), offset 0xD94 .......................................................................... 182
MPU Region Number (MPUNUMBER), offset 0xD98 ....................................................... 184
MPU Region Base Address (MPUBASE), offset 0xD9C ................................................... 185
MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4 ....................................... 185
MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC ...................................... 185
MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4 ....................................... 185
MPU Region Attribute and Size (MPUATTR), offset 0xDA0 ............................................... 187
MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8 .................................. 187
MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0 .................................. 187
MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8 .................................. 187
Coprocessor Access Control (CPAC), offset 0xD88 .......................................................... 190
Floating-Point Context Control (FPCC), offset 0xF34 ........................................................ 191
Floating-Point Context Address (FPCA), offset 0xF38 ...................................................... 193
Floating-Point Default Status Control (FPDSC), offset 0xF3C ........................................... 194
System Control ............................................................................................................................ 207
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Device Identification 0 (DID0), offset 0x000 ..................................................................... 232
Device Identification 1 (DID1), offset 0x004 ..................................................................... 234
Brown-Out Reset Control (PBORCTL), offset 0x030 ........................................................ 237
Raw Interrupt Status (RIS), offset 0x050 .......................................................................... 238
Interrupt Mask Control (IMC), offset 0x054 ...................................................................... 240
Masked Interrupt Status and Clear (MISC), offset 0x058 .................................................. 242
Reset Cause (RESC), offset 0x05C ................................................................................ 245
Run-Mode Clock Configuration (RCC), offset 0x060 ......................................................... 247
GPIO High-Performance Bus Control (GPIOHBCTL), offset 0x06C ................................... 251
Run-Mode Clock Configuration 2 (RCC2), offset 0x070 .................................................... 253
Main Oscillator Control (MOSCCTL), offset 0x07C ........................................................... 256
Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144 ........................................ 257
System Properties (SYSPROP), offset 0x14C .................................................................. 259
Precision Internal Oscillator Calibration (PIOSCCAL), offset 0x150 ................................... 261
Precision Internal Oscillator Statistics (PIOSCSTAT), offset 0x154 .................................... 263
PLL Frequency 0 (PLLFREQ0), offset 0x160 ................................................................... 264
PLL Frequency 1 (PLLFREQ1), offset 0x164 ................................................................... 265
PLL Status (PLLSTAT), offset 0x168 ............................................................................... 266
Sleep Power Configuration (SLPPWRCFG), offset 0x188 ................................................. 267
Deep-Sleep Power Configuration (DSLPPWRCFG), offset 0x18C ..................................... 269
LDO Sleep Power Control (LDOSPCTL), offset 0x1B4 ..................................................... 271
LDO Sleep Power Calibration (LDOSPCAL), offset 0x1B8 ................................................ 273
20
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
Register 59:
Register 60:
Register 61:
Register 62:
Register 63:
Register 64:
Register 65:
LDO Deep-Sleep Power Control (LDODPCTL), offset 0x1BC ........................................... 274
LDO Deep-Sleep Power Calibration (LDODPCAL), offset 0x1C0 ...................................... 276
Sleep / Deep-Sleep Power Mode Status (SDPMST), offset 0x1CC .................................... 277
Watchdog Timer Peripheral Present (PPWD), offset 0x300 ............................................... 280
16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER), offset 0x304 ................. 281
General-Purpose Input/Output Peripheral Present (PPGPIO), offset 0x308 ........................ 283
Micro Direct Memory Access Peripheral Present (PPDMA), offset 0x30C .......................... 286
Hibernation Peripheral Present (PPHIB), offset 0x314 ...................................................... 287
Universal Asynchronous Receiver/Transmitter Peripheral Present (PPUART), offset
0x318 ........................................................................................................................... 288
Synchronous Serial Interface Peripheral Present (PPSSI), offset 0x31C ............................ 290
Inter-Integrated Circuit Peripheral Present (PPI2C), offset 0x320 ...................................... 292
Universal Serial Bus Peripheral Present (PPUSB), offset 0x328 ........................................ 294
Controller Area Network Peripheral Present (PPCAN), offset 0x334 .................................. 295
Analog-to-Digital Converter Peripheral Present (PPADC), offset 0x338 ............................. 296
Analog Comparator Peripheral Present (PPACMP), offset 0x33C ...................................... 297
Pulse Width Modulator Peripheral Present (PPPWM), offset 0x340 ................................... 298
Quadrature Encoder Interface Peripheral Present (PPQEI), offset 0x344 ........................... 299
EEPROM Peripheral Present (PPEEPROM), offset 0x358 ................................................ 300
32/64-Bit Wide General-Purpose Timer Peripheral Present (PPWTIMER), offset 0x35C ..... 301
Watchdog Timer Software Reset (SRWD), offset 0x500 ................................................... 303
16/32-Bit General-Purpose Timer Software Reset (SRTIMER), offset 0x504 ...................... 305
General-Purpose Input/Output Software Reset (SRGPIO), offset 0x508 ............................ 307
Micro Direct Memory Access Software Reset (SRDMA), offset 0x50C ............................... 309
Hibernation Software Reset (SRHIB), offset 0x514 ........................................................... 310
Universal Asynchronous Receiver/Transmitter Software Reset (SRUART), offset 0x518 .... 311
Synchronous Serial Interface Software Reset (SRSSI), offset 0x51C ................................ 313
Inter-Integrated Circuit Software Reset (SRI2C), offset 0x520 ........................................... 315
Controller Area Network Software Reset (SRCAN), offset 0x534 ....................................... 317
Analog-to-Digital Converter Software Reset (SRADC), offset 0x538 .................................. 319
Analog Comparator Software Reset (SRACMP), offset 0x53C .......................................... 321
Pulse Width Modulator Software Reset (SRPWM), offset 0x540 ....................................... 322
Quadrature Encoder Interface Software Reset (SRQEI), offset 0x544 ............................... 324
EEPROM Software Reset (SREEPROM), offset 0x558 .................................................... 326
32/64-Bit Wide General-Purpose Timer Software Reset (SRWTIMER), offset 0x55C .......... 327
Watchdog Timer Run Mode Clock Gating Control (RCGCWD), offset 0x600 ...................... 329
16/32-Bit General-Purpose Timer Run Mode Clock Gating Control (RCGCTIMER), offset
0x604 ........................................................................................................................... 330
General-Purpose Input/Output Run Mode Clock Gating Control (RCGCGPIO), offset
0x608 ........................................................................................................................... 332
Micro Direct Memory Access Run Mode Clock Gating Control (RCGCDMA), offset
0x60C ........................................................................................................................... 334
Hibernation Run Mode Clock Gating Control (RCGCHIB), offset 0x614 ............................. 335
Universal Asynchronous Receiver/Transmitter Run Mode Clock Gating Control (RCGCUART),
offset 0x618 .................................................................................................................. 336
Synchronous Serial Interface Run Mode Clock Gating Control (RCGCSSI), offset
0x61C ........................................................................................................................... 338
Inter-Integrated Circuit Run Mode Clock Gating Control (RCGCI2C), offset 0x620 ............. 340
Controller Area Network Run Mode Clock Gating Control (RCGCCAN), offset 0x634 ......... 342
June 12, 2014
21
Texas Instruments-Production Data
Table of Contents
Register 66:
Register 67:
Register 68:
Register 69:
Register 70:
Register 71:
Register 72:
Register 73:
Register 74:
Register 75:
Register 76:
Register 77:
Register 78:
Register 79:
Register 80:
Register 81:
Register 82:
Register 83:
Register 84:
Register 85:
Register 86:
Register 87:
Register 88:
Register 89:
Register 90:
Register 91:
Register 92:
Register 93:
Register 94:
Register 95:
Register 96:
Analog-to-Digital Converter Run Mode Clock Gating Control (RCGCADC), offset 0x638 .... 343
Analog Comparator Run Mode Clock Gating Control (RCGCACMP), offset 0x63C ............. 344
Pulse Width Modulator Run Mode Clock Gating Control (RCGCPWM), offset 0x640 .......... 345
Quadrature Encoder Interface Run Mode Clock Gating Control (RCGCQEI), offset
0x644 ........................................................................................................................... 346
EEPROM Run Mode Clock Gating Control (RCGCEEPROM), offset 0x658 ....................... 347
32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating Control (RCGCWTIMER),
offset 0x65C .................................................................................................................. 348
Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD), offset 0x700 .................... 350
16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control (SCGCTIMER), offset
0x704 ........................................................................................................................... 351
General-Purpose Input/Output Sleep Mode Clock Gating Control (SCGCGPIO), offset
0x708 ........................................................................................................................... 353
Micro Direct Memory Access Sleep Mode Clock Gating Control (SCGCDMA), offset
0x70C ........................................................................................................................... 355
Hibernation Sleep Mode Clock Gating Control (SCGCHIB), offset 0x714 ........................... 356
Universal Asynchronous Receiver/Transmitter Sleep Mode Clock Gating Control
(SCGCUART), offset 0x718 ............................................................................................ 357
Synchronous Serial Interface Sleep Mode Clock Gating Control (SCGCSSI), offset
0x71C ........................................................................................................................... 359
Inter-Integrated Circuit Sleep Mode Clock Gating Control (SCGCI2C), offset 0x720 ........... 361
Controller Area Network Sleep Mode Clock Gating Control (SCGCCAN), offset 0x734 ....... 363
Analog-to-Digital Converter Sleep Mode Clock Gating Control (SCGCADC), offset
0x738 ........................................................................................................................... 364
Analog Comparator Sleep Mode Clock Gating Control (SCGCACMP), offset 0x73C .......... 365
Pulse Width Modulator Sleep Mode Clock Gating Control (SCGCPWM), offset 0x740 ........ 366
Quadrature Encoder Interface Sleep Mode Clock Gating Control (SCGCQEI), offset
0x744 ........................................................................................................................... 367
EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM), offset 0x758 ..................... 368
32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating Control (SCGCWTIMER),
offset 0x75C .................................................................................................................. 369
Watchdog Timer Deep-Sleep Mode Clock Gating Control (DCGCWD), offset 0x800 .......... 371
16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCTIMER),
offset 0x804 .................................................................................................................. 372
General-Purpose Input/Output Deep-Sleep Mode Clock Gating Control (DCGCGPIO), offset
0x808 ........................................................................................................................... 374
Micro Direct Memory Access Deep-Sleep Mode Clock Gating Control (DCGCDMA), offset
0x80C ........................................................................................................................... 376
Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB), offset 0x814 .................. 377
Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode Clock Gating Control
(DCGCUART), offset 0x818 ............................................................................................ 378
Synchronous Serial Interface Deep-Sleep Mode Clock Gating Control (DCGCSSI), offset
0x81C ........................................................................................................................... 380
Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control (DCGCI2C), offset
0x820 ........................................................................................................................... 382
Controller Area Network Deep-Sleep Mode Clock Gating Control (DCGCCAN), offset
0x834 ........................................................................................................................... 384
Analog-to-Digital Converter Deep-Sleep Mode Clock Gating Control (DCGCADC), offset
0x838 ........................................................................................................................... 385
22
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 97:
Register 98:
Register 99:
Register 100:
Register 101:
Register 102:
Register 103:
Register 104:
Register 105:
Register 106:
Register 107:
Register 108:
Register 109:
Register 110:
Register 111:
Register 112:
Register 113:
Register 114:
Register 115:
Register 116:
Register 117:
Register 118:
Register 119:
Register 120:
Register 121:
Register 122:
Register 123:
Register 124:
Register 125:
Register 126:
Register 127:
Register 128:
Register 129:
Register 130:
Register 131:
Register 132:
Register 133:
Register 134:
Register 135:
Register 136:
Register 137:
Register 138:
Register 139:
Analog Comparator Deep-Sleep Mode Clock Gating Control (DCGCACMP), offset
0x83C ........................................................................................................................... 386
Pulse Width Modulator Deep-Sleep Mode Clock Gating Control (DCGCPWM), offset
0x840 ........................................................................................................................... 387
Quadrature Encoder Interface Deep-Sleep Mode Clock Gating Control (DCGCQEI), offset
0x844 ........................................................................................................................... 388
EEPROM Deep-Sleep Mode Clock Gating Control (DCGCEEPROM), offset 0x858 ........... 389
32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock Gating Control
(DCGCWTIMER), offset 0x85C ...................................................................................... 390
Watchdog Timer Peripheral Ready (PRWD), offset 0xA00 ................................................ 392
16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER), offset 0xA04 ................... 393
General-Purpose Input/Output Peripheral Ready (PRGPIO), offset 0xA08 ......................... 395
Micro Direct Memory Access Peripheral Ready (PRDMA), offset 0xA0C ........................... 397
Hibernation Peripheral Ready (PRHIB), offset 0xA14 ....................................................... 398
Universal Asynchronous Receiver/Transmitter Peripheral Ready (PRUART), offset
0xA18 ........................................................................................................................... 399
Synchronous Serial Interface Peripheral Ready (PRSSI), offset 0xA1C ............................. 401
Inter-Integrated Circuit Peripheral Ready (PRI2C), offset 0xA20 ....................................... 403
Controller Area Network Peripheral Ready (PRCAN), offset 0xA34 ................................... 405
Analog-to-Digital Converter Peripheral Ready (PRADC), offset 0xA38 ............................... 406
Analog Comparator Peripheral Ready (PRACMP), offset 0xA3C ....................................... 407
Pulse Width Modulator Peripheral Ready (PRPWM), offset 0xA40 .................................... 408
Quadrature Encoder Interface Peripheral Ready (PRQEI), offset 0xA44 ............................ 409
EEPROM Peripheral Ready (PREEPROM), offset 0xA58 ................................................. 410
32/64-Bit Wide General-Purpose Timer Peripheral Ready (PRWTIMER), offset 0xA5C ...... 411
Device Capabilities 0 (DC0), offset 0x008 ........................................................................ 413
Device Capabilities 1 (DC1), offset 0x010 ........................................................................ 415
Device Capabilities 2 (DC2), offset 0x014 ........................................................................ 418
Device Capabilities 3 (DC3), offset 0x018 ........................................................................ 421
Device Capabilities 4 (DC4), offset 0x01C ....................................................................... 425
Device Capabilities 5 (DC5), offset 0x020 ........................................................................ 428
Device Capabilities 6 (DC6), offset 0x024 ........................................................................ 430
Device Capabilities 7 (DC7), offset 0x028 ........................................................................ 431
Device Capabilities 8 (DC8), offset 0x02C ....................................................................... 434
Software Reset Control 0 (SRCR0), offset 0x040 ............................................................. 437
Software Reset Control 1 (SRCR1), offset 0x044 ............................................................. 439
Software Reset Control 2 (SRCR2), offset 0x048 ............................................................. 442
Run Mode Clock Gating Control Register 0 (RCGC0), offset 0x100 ................................... 444
Run Mode Clock Gating Control Register 1 (RCGC1), offset 0x104 ................................... 448
Run Mode Clock Gating Control Register 2 (RCGC2), offset 0x108 ................................... 452
Sleep Mode Clock Gating Control Register 0 (SCGC0), offset 0x110 ................................. 454
Sleep Mode Clock Gating Control Register 1 (SCGC1), offset 0x114 ................................. 457
Sleep Mode Clock Gating Control Register 2 (SCGC2), offset 0x118 ................................. 460
Deep Sleep Mode Clock Gating Control Register 0 (DCGC0), offset 0x120 ....................... 462
Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1), offset 0x124 ....................... 465
Deep Sleep Mode Clock Gating Control Register 2 (DCGC2), offset 0x128 ....................... 468
Device Capabilities 9 (DC9), offset 0x190 ........................................................................ 470
Non-Volatile Memory Information (NVMSTAT), offset 0x1A0 ............................................. 472
June 12, 2014
23
Texas Instruments-Production Data
Table of Contents
System Exception Module .......................................................................................................... 473
Register 1:
Register 2:
Register 3:
Register 4:
System Exception Raw Interrupt Status (SYSEXCRIS), offset 0x000 ................................
System Exception Interrupt Mask (SYSEXCIM), offset 0x004 ...........................................
System Exception Masked Interrupt Status (SYSEXCMIS), offset 0x008 ...........................
System Exception Interrupt Clear (SYSEXCIC), offset 0x00C ...........................................
474
476
478
480
Hibernation Module ..................................................................................................................... 481
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Hibernation RTC Counter (HIBRTCC), offset 0x000 .........................................................
Hibernation RTC Match 0 (HIBRTCM0), offset 0x004 .......................................................
Hibernation RTC Load (HIBRTCLD), offset 0x00C ...........................................................
Hibernation Control (HIBCTL), offset 0x010 .....................................................................
Hibernation Interrupt Mask (HIBIM), offset 0x014 .............................................................
Hibernation Raw Interrupt Status (HIBRIS), offset 0x018 ..................................................
Hibernation Masked Interrupt Status (HIBMIS), offset 0x01C ............................................
Hibernation Interrupt Clear (HIBIC), offset 0x020 .............................................................
Hibernation RTC Trim (HIBRTCT), offset 0x024 ...............................................................
Hibernation RTC Sub Seconds (HIBRTCSS), offset 0x028 ...............................................
Hibernation Data (HIBDATA), offset 0x030-0x06F ............................................................
495
496
497
498
502
504
506
508
509
510
511
Internal Memory ........................................................................................................................... 512
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Flash Memory Address (FMA), offset 0x000 .................................................................... 530
Flash Memory Data (FMD), offset 0x004 ......................................................................... 531
Flash Memory Control (FMC), offset 0x008 ..................................................................... 532
Flash Controller Raw Interrupt Status (FCRIS), offset 0x00C ............................................ 534
Flash Controller Interrupt Mask (FCIM), offset 0x010 ........................................................ 537
Flash Controller Masked Interrupt Status and Clear (FCMISC), offset 0x014 ..................... 539
Flash Memory Control 2 (FMC2), offset 0x020 ................................................................. 542
Flash Write Buffer Valid (FWBVAL), offset 0x030 ............................................................. 543
Flash Write Buffer n (FWBn), offset 0x100 - 0x17C .......................................................... 544
Flash Size (FSIZE), offset 0xFC0 .................................................................................... 545
SRAM Size (SSIZE), offset 0xFC4 .................................................................................. 546
ROM Software Map (ROMSWMAP), offset 0xFCC ........................................................... 547
EEPROM Size Information (EESIZE), offset 0x000 .......................................................... 548
EEPROM Current Block (EEBLOCK), offset 0x004 .......................................................... 549
EEPROM Current Offset (EEOFFSET), offset 0x008 ........................................................ 550
EEPROM Read-Write (EERDWR), offset 0x010 .............................................................. 551
EEPROM Read-Write with Increment (EERDWRINC), offset 0x014 .................................. 552
EEPROM Done Status (EEDONE), offset 0x018 .............................................................. 553
EEPROM Support Control and Status (EESUPP), offset 0x01C ........................................ 555
EEPROM Unlock (EEUNLOCK), offset 0x020 .................................................................. 557
EEPROM Protection (EEPROT), offset 0x030 ................................................................. 558
EEPROM Password (EEPASS0), offset 0x034 ................................................................. 560
EEPROM Password (EEPASS1), offset 0x038 ................................................................. 560
EEPROM Password (EEPASS2), offset 0x03C ................................................................ 560
EEPROM Interrupt (EEINT), offset 0x040 ........................................................................ 561
EEPROM Block Hide (EEHIDE), offset 0x050 .................................................................. 562
EEPROM Debug Mass Erase (EEDBGME), offset 0x080 ................................................. 563
EEPROM Peripheral Properties (EEPROMPP), offset 0xFC0 ........................................... 564
ROM Control (RMCTL), offset 0x0F0 .............................................................................. 565
Flash Memory Protection Read Enable 0 (FMPRE0), offset 0x130 and 0x200 ................... 566
24
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Flash Memory Protection Read Enable 1 (FMPRE1), offset 0x204 .................................... 566
Flash Memory Protection Program Enable 0 (FMPPE0), offset 0x134 and 0x400 ............... 567
Flash Memory Protection Program Enable 1 (FMPPE1), offset 0x404 ............................... 567
Boot Configuration (BOOTCFG), offset 0x1D0 ................................................................. 568
User Register 0 (USER_REG0), offset 0x1E0 .................................................................. 571
User Register 1 (USER_REG1), offset 0x1E4 .................................................................. 571
User Register 2 (USER_REG2), offset 0x1E8 .................................................................. 571
User Register 3 (USER_REG3), offset 0x1EC ................................................................. 571
Micro Direct Memory Access (μDMA) ........................................................................................ 572
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
DMA Channel Source Address End Pointer (DMASRCENDP), offset 0x000 ...................... 596
DMA Channel Destination Address End Pointer (DMADSTENDP), offset 0x004 ................ 597
DMA Channel Control Word (DMACHCTL), offset 0x008 .................................................. 598
DMA Status (DMASTAT), offset 0x000 ............................................................................ 603
DMA Configuration (DMACFG), offset 0x004 ................................................................... 605
DMA Channel Control Base Pointer (DMACTLBASE), offset 0x008 .................................. 606
DMA Alternate Channel Control Base Pointer (DMAALTBASE), offset 0x00C .................... 607
DMA Channel Wait-on-Request Status (DMAWAITSTAT), offset 0x010 ............................. 608
DMA Channel Software Request (DMASWREQ), offset 0x014 ......................................... 609
DMA Channel Useburst Set (DMAUSEBURSTSET), offset 0x018 .................................... 610
DMA Channel Useburst Clear (DMAUSEBURSTCLR), offset 0x01C ................................. 611
DMA Channel Request Mask Set (DMAREQMASKSET), offset 0x020 .............................. 612
DMA Channel Request Mask Clear (DMAREQMASKCLR), offset 0x024 ........................... 613
DMA Channel Enable Set (DMAENASET), offset 0x028 ................................................... 614
DMA Channel Enable Clear (DMAENACLR), offset 0x02C ............................................... 615
DMA Channel Primary Alternate Set (DMAALTSET), offset 0x030 .................................... 616
DMA Channel Primary Alternate Clear (DMAALTCLR), offset 0x034 ................................. 617
DMA Channel Priority Set (DMAPRIOSET), offset 0x038 ................................................. 618
DMA Channel Priority Clear (DMAPRIOCLR), offset 0x03C .............................................. 619
DMA Bus Error Clear (DMAERRCLR), offset 0x04C ........................................................ 620
DMA Channel Assignment (DMACHASGN), offset 0x500 ................................................. 621
DMA Channel Interrupt Status (DMACHIS), offset 0x504 .................................................. 622
DMA Channel Map Select 0 (DMACHMAP0), offset 0x510 ............................................... 623
DMA Channel Map Select 1 (DMACHMAP1), offset 0x514 ............................................... 624
DMA Channel Map Select 2 (DMACHMAP2), offset 0x518 ............................................... 625
DMA Channel Map Select 3 (DMACHMAP3), offset 0x51C .............................................. 626
DMA Peripheral Identification 0 (DMAPeriphID0), offset 0xFE0 ......................................... 627
DMA Peripheral Identification 1 (DMAPeriphID1), offset 0xFE4 ......................................... 628
DMA Peripheral Identification 2 (DMAPeriphID2), offset 0xFE8 ......................................... 629
DMA Peripheral Identification 3 (DMAPeriphID3), offset 0xFEC ........................................ 630
DMA Peripheral Identification 4 (DMAPeriphID4), offset 0xFD0 ......................................... 631
DMA PrimeCell Identification 0 (DMAPCellID0), offset 0xFF0 ........................................... 632
DMA PrimeCell Identification 1 (DMAPCellID1), offset 0xFF4 ........................................... 633
DMA PrimeCell Identification 2 (DMAPCellID2), offset 0xFF8 ........................................... 634
DMA PrimeCell Identification 3 (DMAPCellID3), offset 0xFFC ........................................... 635
General-Purpose Input/Outputs (GPIOs) ................................................................................... 636
Register 1:
Register 2:
Register 3:
GPIO Data (GPIODATA), offset 0x000 ............................................................................ 649
GPIO Direction (GPIODIR), offset 0x400 ......................................................................... 650
GPIO Interrupt Sense (GPIOIS), offset 0x404 .................................................................. 651
June 12, 2014
25
Texas Instruments-Production Data
Table of Contents
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
GPIO Interrupt Both Edges (GPIOIBE), offset 0x408 ........................................................ 652
GPIO Interrupt Event (GPIOIEV), offset 0x40C ................................................................ 653
GPIO Interrupt Mask (GPIOIM), offset 0x410 ................................................................... 654
GPIO Raw Interrupt Status (GPIORIS), offset 0x414 ........................................................ 655
GPIO Masked Interrupt Status (GPIOMIS), offset 0x418 ................................................... 656
GPIO Interrupt Clear (GPIOICR), offset 0x41C ................................................................ 657
GPIO Alternate Function Select (GPIOAFSEL), offset 0x420 ............................................ 658
GPIO 2-mA Drive Select (GPIODR2R), offset 0x500 ........................................................ 660
GPIO 4-mA Drive Select (GPIODR4R), offset 0x504 ........................................................ 661
GPIO 8-mA Drive Select (GPIODR8R), offset 0x508 ........................................................ 662
GPIO Open Drain Select (GPIOODR), offset 0x50C ......................................................... 663
GPIO Pull-Up Select (GPIOPUR), offset 0x510 ................................................................ 664
GPIO Pull-Down Select (GPIOPDR), offset 0x514 ........................................................... 666
GPIO Slew Rate Control Select (GPIOSLR), offset 0x518 ................................................ 668
GPIO Digital Enable (GPIODEN), offset 0x51C ................................................................ 669
GPIO Lock (GPIOLOCK), offset 0x520 ............................................................................ 671
GPIO Commit (GPIOCR), offset 0x524 ............................................................................ 672
GPIO Analog Mode Select (GPIOAMSEL), offset 0x528 ................................................... 674
GPIO Port Control (GPIOPCTL), offset 0x52C ................................................................. 675
GPIO ADC Control (GPIOADCCTL), offset 0x530 ............................................................ 677
GPIO DMA Control (GPIODMACTL), offset 0x534 ........................................................... 678
GPIO Peripheral Identification 4 (GPIOPeriphID4), offset 0xFD0 ....................................... 679
GPIO Peripheral Identification 5 (GPIOPeriphID5), offset 0xFD4 ....................................... 680
GPIO Peripheral Identification 6 (GPIOPeriphID6), offset 0xFD8 ....................................... 681
GPIO Peripheral Identification 7 (GPIOPeriphID7), offset 0xFDC ...................................... 682
GPIO Peripheral Identification 0 (GPIOPeriphID0), offset 0xFE0 ....................................... 683
GPIO Peripheral Identification 1 (GPIOPeriphID1), offset 0xFE4 ....................................... 684
GPIO Peripheral Identification 2 (GPIOPeriphID2), offset 0xFE8 ....................................... 685
GPIO Peripheral Identification 3 (GPIOPeriphID3), offset 0xFEC ...................................... 686
GPIO PrimeCell Identification 0 (GPIOPCellID0), offset 0xFF0 .......................................... 687
GPIO PrimeCell Identification 1 (GPIOPCellID1), offset 0xFF4 .......................................... 688
GPIO PrimeCell Identification 2 (GPIOPCellID2), offset 0xFF8 .......................................... 689
GPIO PrimeCell Identification 3 (GPIOPCellID3), offset 0xFFC ......................................... 690
General-Purpose Timers ............................................................................................................. 691
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
GPTM Configuration (GPTMCFG), offset 0x000 .............................................................. 714
GPTM Timer A Mode (GPTMTAMR), offset 0x004 ........................................................... 716
GPTM Timer B Mode (GPTMTBMR), offset 0x008 ........................................................... 720
GPTM Control (GPTMCTL), offset 0x00C ........................................................................ 724
GPTM Synchronize (GPTMSYNC), offset 0x010 .............................................................. 728
GPTM Interrupt Mask (GPTMIMR), offset 0x018 .............................................................. 732
GPTM Raw Interrupt Status (GPTMRIS), offset 0x01C ..................................................... 735
GPTM Masked Interrupt Status (GPTMMIS), offset 0x020 ................................................ 738
GPTM Interrupt Clear (GPTMICR), offset 0x024 .............................................................. 741
GPTM Timer A Interval Load (GPTMTAILR), offset 0x028 ................................................ 743
GPTM Timer B Interval Load (GPTMTBILR), offset 0x02C ................................................ 744
GPTM Timer A Match (GPTMTAMATCHR), offset 0x030 .................................................. 745
GPTM Timer B Match (GPTMTBMATCHR), offset 0x034 ................................................. 746
GPTM Timer A Prescale (GPTMTAPR), offset 0x038 ....................................................... 747
26
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
GPTM Timer B Prescale (GPTMTBPR), offset 0x03C ...................................................... 748
GPTM TimerA Prescale Match (GPTMTAPMR), offset 0x040 ........................................... 749
GPTM TimerB Prescale Match (GPTMTBPMR), offset 0x044 ........................................... 750
GPTM Timer A (GPTMTAR), offset 0x048 ....................................................................... 751
GPTM Timer B (GPTMTBR), offset 0x04C ....................................................................... 752
GPTM Timer A Value (GPTMTAV), offset 0x050 ............................................................... 753
GPTM Timer B Value (GPTMTBV), offset 0x054 .............................................................. 754
GPTM RTC Predivide (GPTMRTCPD), offset 0x058 ........................................................ 755
GPTM Timer A Prescale Snapshot (GPTMTAPS), offset 0x05C ........................................ 756
GPTM Timer B Prescale Snapshot (GPTMTBPS), offset 0x060 ........................................ 757
GPTM Timer A Prescale Value (GPTMTAPV), offset 0x064 .............................................. 758
GPTM Timer B Prescale Value (GPTMTBPV), offset 0x068 .............................................. 759
GPTM Peripheral Properties (GPTMPP), offset 0xFC0 ..................................................... 760
Watchdog Timers ......................................................................................................................... 761
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Watchdog Load (WDTLOAD), offset 0x000 ...................................................................... 765
Watchdog Value (WDTVALUE), offset 0x004 ................................................................... 766
Watchdog Control (WDTCTL), offset 0x008 ..................................................................... 767
Watchdog Interrupt Clear (WDTICR), offset 0x00C .......................................................... 769
Watchdog Raw Interrupt Status (WDTRIS), offset 0x010 .................................................. 770
Watchdog Masked Interrupt Status (WDTMIS), offset 0x014 ............................................. 771
Watchdog Test (WDTTEST), offset 0x418 ....................................................................... 772
Watchdog Lock (WDTLOCK), offset 0xC00 ..................................................................... 773
Watchdog Peripheral Identification 4 (WDTPeriphID4), offset 0xFD0 ................................. 774
Watchdog Peripheral Identification 5 (WDTPeriphID5), offset 0xFD4 ................................. 775
Watchdog Peripheral Identification 6 (WDTPeriphID6), offset 0xFD8 ................................. 776
Watchdog Peripheral Identification 7 (WDTPeriphID7), offset 0xFDC ................................ 777
Watchdog Peripheral Identification 0 (WDTPeriphID0), offset 0xFE0 ................................. 778
Watchdog Peripheral Identification 1 (WDTPeriphID1), offset 0xFE4 ................................. 779
Watchdog Peripheral Identification 2 (WDTPeriphID2), offset 0xFE8 ................................. 780
Watchdog Peripheral Identification 3 (WDTPeriphID3), offset 0xFEC ................................. 781
Watchdog PrimeCell Identification 0 (WDTPCellID0), offset 0xFF0 .................................... 782
Watchdog PrimeCell Identification 1 (WDTPCellID1), offset 0xFF4 .................................... 783
Watchdog PrimeCell Identification 2 (WDTPCellID2), offset 0xFF8 .................................... 784
Watchdog PrimeCell Identification 3 (WDTPCellID3 ), offset 0xFFC .................................. 785
Analog-to-Digital Converter (ADC) ............................................................................................. 786
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
ADC Active Sample Sequencer (ADCACTSS), offset 0x000 ............................................. 808
ADC Raw Interrupt Status (ADCRIS), offset 0x004 ........................................................... 810
ADC Interrupt Mask (ADCIM), offset 0x008 ..................................................................... 812
ADC Interrupt Status and Clear (ADCISC), offset 0x00C .................................................. 815
ADC Overflow Status (ADCOSTAT), offset 0x010 ............................................................ 818
ADC Event Multiplexer Select (ADCEMUX), offset 0x014 ................................................. 820
ADC Underflow Status (ADCUSTAT), offset 0x018 ........................................................... 825
ADC Trigger Source Select (ADCTSSEL), offset 0x01C ................................................... 826
ADC Sample Sequencer Priority (ADCSSPRI), offset 0x020 ............................................. 828
ADC Sample Phase Control (ADCSPC), offset 0x024 ...................................................... 830
ADC Processor Sample Sequence Initiate (ADCPSSI), offset 0x028 ................................. 832
ADC Sample Averaging Control (ADCSAC), offset 0x030 ................................................. 834
ADC Digital Comparator Interrupt Status and Clear (ADCDCISC), offset 0x034 ................. 835
June 12, 2014
27
Texas Instruments-Production Data
Table of Contents
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
ADC Control (ADCCTL), offset 0x038 ............................................................................. 837
ADC Sample Sequence Input Multiplexer Select 0 (ADCSSMUX0), offset 0x040 ............... 838
ADC Sample Sequence Control 0 (ADCSSCTL0), offset 0x044 ........................................ 840
ADC Sample Sequence Result FIFO 0 (ADCSSFIFO0), offset 0x048 ................................ 847
ADC Sample Sequence Result FIFO 1 (ADCSSFIFO1), offset 0x068 ................................ 847
ADC Sample Sequence Result FIFO 2 (ADCSSFIFO2), offset 0x088 ................................ 847
ADC Sample Sequence Result FIFO 3 (ADCSSFIFO3), offset 0x0A8 ............................... 847
ADC Sample Sequence FIFO 0 Status (ADCSSFSTAT0), offset 0x04C ............................. 848
ADC Sample Sequence FIFO 1 Status (ADCSSFSTAT1), offset 0x06C ............................. 848
ADC Sample Sequence FIFO 2 Status (ADCSSFSTAT2), offset 0x08C ............................ 848
ADC Sample Sequence FIFO 3 Status (ADCSSFSTAT3), offset 0x0AC ............................ 848
ADC Sample Sequence 0 Operation (ADCSSOP0), offset 0x050 ...................................... 850
ADC Sample Sequence 0 Digital Comparator Select (ADCSSDC0), offset 0x054 .............. 852
ADC Sample Sequence Input Multiplexer Select 1 (ADCSSMUX1), offset 0x060 ............... 854
ADC Sample Sequence Input Multiplexer Select 2 (ADCSSMUX2), offset 0x080 ............... 854
ADC Sample Sequence Control 1 (ADCSSCTL1), offset 0x064 ........................................ 855
ADC Sample Sequence Control 2 (ADCSSCTL2), offset 0x084 ........................................ 855
ADC Sample Sequence 1 Operation (ADCSSOP1), offset 0x070 ...................................... 859
ADC Sample Sequence 2 Operation (ADCSSOP2), offset 0x090 ..................................... 859
ADC Sample Sequence 1 Digital Comparator Select (ADCSSDC1), offset 0x074 .............. 860
ADC Sample Sequence 2 Digital Comparator Select (ADCSSDC2), offset 0x094 .............. 860
ADC Sample Sequence Input Multiplexer Select 3 (ADCSSMUX3), offset 0x0A0 ............... 862
ADC Sample Sequence Control 3 (ADCSSCTL3), offset 0x0A4 ........................................ 863
ADC Sample Sequence 3 Operation (ADCSSOP3), offset 0x0B0 ..................................... 865
ADC Sample Sequence 3 Digital Comparator Select (ADCSSDC3), offset 0x0B4 .............. 866
ADC Digital Comparator Reset Initial Conditions (ADCDCRIC), offset 0xD00 ..................... 867
ADC Digital Comparator Control 0 (ADCDCCTL0), offset 0xE00 ....................................... 872
ADC Digital Comparator Control 1 (ADCDCCTL1), offset 0xE04 ....................................... 872
ADC Digital Comparator Control 2 (ADCDCCTL2), offset 0xE08 ....................................... 872
ADC Digital Comparator Control 3 (ADCDCCTL3), offset 0xE0C ...................................... 872
ADC Digital Comparator Control 4 (ADCDCCTL4), offset 0xE10 ....................................... 872
ADC Digital Comparator Control 5 (ADCDCCTL5), offset 0xE14 ....................................... 872
ADC Digital Comparator Control 6 (ADCDCCTL6), offset 0xE18 ....................................... 872
ADC Digital Comparator Control 7 (ADCDCCTL7), offset 0xE1C ...................................... 872
ADC Digital Comparator Range 0 (ADCDCCMP0), offset 0xE40 ....................................... 875
ADC Digital Comparator Range 1 (ADCDCCMP1), offset 0xE44 ....................................... 875
ADC Digital Comparator Range 2 (ADCDCCMP2), offset 0xE48 ....................................... 875
ADC Digital Comparator Range 3 (ADCDCCMP3), offset 0xE4C ...................................... 875
ADC Digital Comparator Range 4 (ADCDCCMP4), offset 0xE50 ....................................... 875
ADC Digital Comparator Range 5 (ADCDCCMP5), offset 0xE54 ....................................... 875
ADC Digital Comparator Range 6 (ADCDCCMP6), offset 0xE58 ....................................... 875
ADC Digital Comparator Range 7 (ADCDCCMP7), offset 0xE5C ...................................... 875
ADC Peripheral Properties (ADCPP), offset 0xFC0 .......................................................... 876
ADC Peripheral Configuration (ADCPC), offset 0xFC4 ..................................................... 878
ADC Clock Configuration (ADCCC), offset 0xFC8 ............................................................ 879
Universal Asynchronous Receivers/Transmitters (UARTs) ..................................................... 880
Register 1:
Register 2:
UART Data (UARTDR), offset 0x000 ............................................................................... 893
UART Receive Status/Error Clear (UARTRSR/UARTECR), offset 0x004 ........................... 895
28
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
UART Flag (UARTFR), offset 0x018 ................................................................................ 898
UART IrDA Low-Power Register (UARTILPR), offset 0x020 ............................................. 900
UART Integer Baud-Rate Divisor (UARTIBRD), offset 0x024 ............................................ 901
UART Fractional Baud-Rate Divisor (UARTFBRD), offset 0x028 ....................................... 902
UART Line Control (UARTLCRH), offset 0x02C ............................................................... 903
UART Control (UARTCTL), offset 0x030 ......................................................................... 905
UART Interrupt FIFO Level Select (UARTIFLS), offset 0x034 ........................................... 909
UART Interrupt Mask (UARTIM), offset 0x038 ................................................................. 911
UART Raw Interrupt Status (UARTRIS), offset 0x03C ...................................................... 914
UART Masked Interrupt Status (UARTMIS), offset 0x040 ................................................. 917
UART Interrupt Clear (UARTICR), offset 0x044 ............................................................... 920
UART DMA Control (UARTDMACTL), offset 0x048 .......................................................... 922
UART 9-Bit Self Address (UART9BITADDR), offset 0x0A4 ............................................... 923
UART 9-Bit Self Address Mask (UART9BITAMASK), offset 0x0A8 .................................... 924
UART Peripheral Properties (UARTPP), offset 0xFC0 ...................................................... 925
UART Clock Configuration (UARTCC), offset 0xFC8 ........................................................ 926
UART Peripheral Identification 4 (UARTPeriphID4), offset 0xFD0 ..................................... 927
UART Peripheral Identification 5 (UARTPeriphID5), offset 0xFD4 ..................................... 928
UART Peripheral Identification 6 (UARTPeriphID6), offset 0xFD8 ..................................... 929
UART Peripheral Identification 7 (UARTPeriphID7), offset 0xFDC ..................................... 930
UART Peripheral Identification 0 (UARTPeriphID0), offset 0xFE0 ...................................... 931
UART Peripheral Identification 1 (UARTPeriphID1), offset 0xFE4 ...................................... 932
UART Peripheral Identification 2 (UARTPeriphID2), offset 0xFE8 ...................................... 933
UART Peripheral Identification 3 (UARTPeriphID3), offset 0xFEC ..................................... 934
UART PrimeCell Identification 0 (UARTPCellID0), offset 0xFF0 ........................................ 935
UART PrimeCell Identification 1 (UARTPCellID1), offset 0xFF4 ........................................ 936
UART PrimeCell Identification 2 (UARTPCellID2), offset 0xFF8 ........................................ 937
UART PrimeCell Identification 3 (UARTPCellID3), offset 0xFFC ........................................ 938
Synchronous Serial Interface (SSI) ............................................................................................ 939
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
SSI Control 0 (SSICR0), offset 0x000 .............................................................................. 956
SSI Control 1 (SSICR1), offset 0x004 .............................................................................. 958
SSI Data (SSIDR), offset 0x008 ...................................................................................... 960
SSI Status (SSISR), offset 0x00C ................................................................................... 961
SSI Clock Prescale (SSICPSR), offset 0x010 .................................................................. 963
SSI Interrupt Mask (SSIIM), offset 0x014 ......................................................................... 964
SSI Raw Interrupt Status (SSIRIS), offset 0x018 .............................................................. 965
SSI Masked Interrupt Status (SSIMIS), offset 0x01C ........................................................ 967
SSI Interrupt Clear (SSIICR), offset 0x020 ....................................................................... 969
SSI DMA Control (SSIDMACTL), offset 0x024 ................................................................. 970
SSI Clock Configuration (SSICC), offset 0xFC8 ............................................................... 971
SSI Peripheral Identification 4 (SSIPeriphID4), offset 0xFD0 ............................................. 972
SSI Peripheral Identification 5 (SSIPeriphID5), offset 0xFD4 ............................................. 973
SSI Peripheral Identification 6 (SSIPeriphID6), offset 0xFD8 ............................................. 974
SSI Peripheral Identification 7 (SSIPeriphID7), offset 0xFDC ............................................ 975
SSI Peripheral Identification 0 (SSIPeriphID0), offset 0xFE0 ............................................. 976
SSI Peripheral Identification 1 (SSIPeriphID1), offset 0xFE4 ............................................. 977
SSI Peripheral Identification 2 (SSIPeriphID2), offset 0xFE8 ............................................. 978
SSI Peripheral Identification 3 (SSIPeriphID3), offset 0xFEC ............................................ 979
June 12, 2014
29
Texas Instruments-Production Data
Table of Contents
Register 20:
Register 21:
Register 22:
Register 23:
SSI PrimeCell Identification 0 (SSIPCellID0), offset 0xFF0 ...............................................
SSI PrimeCell Identification 1 (SSIPCellID1), offset 0xFF4 ...............................................
SSI PrimeCell Identification 2 (SSIPCellID2), offset 0xFF8 ...............................................
SSI PrimeCell Identification 3 (SSIPCellID3), offset 0xFFC ...............................................
980
981
982
983
Inter-Integrated Circuit (I2C) Interface ........................................................................................ 984
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
I2C Master Slave Address (I2CMSA), offset 0x000 ......................................................... 1006
I2C Master Control/Status (I2CMCS), offset 0x004 ......................................................... 1007
I2C Master Data (I2CMDR), offset 0x008 ....................................................................... 1012
I2C Master Timer Period (I2CMTPR), offset 0x00C ......................................................... 1013
I2C Master Interrupt Mask (I2CMIMR), offset 0x010 ....................................................... 1014
I2C Master Raw Interrupt Status (I2CMRIS), offset 0x014 ............................................... 1015
I2C Master Masked Interrupt Status (I2CMMIS), offset 0x018 .......................................... 1016
I2C Master Interrupt Clear (I2CMICR), offset 0x01C ....................................................... 1017
I2C Master Configuration (I2CMCR), offset 0x020 .......................................................... 1018
I2C Master Clock Low Timeout Count (I2CMCLKOCNT), offset 0x024 ............................. 1020
I2C Master Bus Monitor (I2CMBMON), offset 0x02C ....................................................... 1021
I2C Master Configuration 2 (I2CMCR2), offset 0x038 ...................................................... 1022
I2C Slave Own Address (I2CSOAR), offset 0x800 .......................................................... 1023
I2C Slave Control/Status (I2CSCSR), offset 0x804 ......................................................... 1024
I2C Slave Data (I2CSDR), offset 0x808 ......................................................................... 1026
I2C Slave Interrupt Mask (I2CSIMR), offset 0x80C ......................................................... 1027
I2C Slave Raw Interrupt Status (I2CSRIS), offset 0x810 ................................................. 1028
I2C Slave Masked Interrupt Status (I2CSMIS), offset 0x814 ............................................ 1029
I2C Slave Interrupt Clear (I2CSICR), offset 0x818 .......................................................... 1030
I2C Slave Own Address 2 (I2CSOAR2), offset 0x81C ..................................................... 1031
I2C Slave ACK Control (I2CSACKCTL), offset 0x820 ...................................................... 1032
I2C Peripheral Properties (I2CPP), offset 0xFC0 ............................................................ 1033
I2C Peripheral Configuration (I2CPC), offset 0xFC4 ....................................................... 1034
Controller Area Network (CAN) Module ................................................................................... 1035
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
CAN Control (CANCTL), offset 0x000 ............................................................................ 1057
CAN Status (CANSTS), offset 0x004 ............................................................................. 1059
CAN Error Counter (CANERR), offset 0x008 ................................................................. 1062
CAN Bit Timing (CANBIT), offset 0x00C ........................................................................ 1063
CAN Interrupt (CANINT), offset 0x010 ........................................................................... 1064
CAN Test (CANTST), offset 0x014 ................................................................................ 1065
CAN Baud Rate Prescaler Extension (CANBRPE), offset 0x018 ..................................... 1067
CAN IF1 Command Request (CANIF1CRQ), offset 0x020 .............................................. 1068
CAN IF2 Command Request (CANIF2CRQ), offset 0x080 .............................................. 1068
CAN IF1 Command Mask (CANIF1CMSK), offset 0x024 ................................................ 1069
CAN IF2 Command Mask (CANIF2CMSK), offset 0x084 ................................................ 1069
CAN IF1 Mask 1 (CANIF1MSK1), offset 0x028 .............................................................. 1072
CAN IF2 Mask 1 (CANIF2MSK1), offset 0x088 .............................................................. 1072
CAN IF1 Mask 2 (CANIF1MSK2), offset 0x02C .............................................................. 1073
CAN IF2 Mask 2 (CANIF2MSK2), offset 0x08C .............................................................. 1073
CAN IF1 Arbitration 1 (CANIF1ARB1), offset 0x030 ....................................................... 1075
CAN IF2 Arbitration 1 (CANIF2ARB1), offset 0x090 ....................................................... 1075
CAN IF1 Arbitration 2 (CANIF1ARB2), offset 0x034 ....................................................... 1076
30
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
CAN IF2 Arbitration 2 (CANIF2ARB2), offset 0x094 ....................................................... 1076
CAN IF1 Message Control (CANIF1MCTL), offset 0x038 ................................................ 1078
CAN IF2 Message Control (CANIF2MCTL), offset 0x098 ................................................ 1078
CAN IF1 Data A1 (CANIF1DA1), offset 0x03C ............................................................... 1081
CAN IF1 Data A2 (CANIF1DA2), offset 0x040 ................................................................ 1081
CAN IF1 Data B1 (CANIF1DB1), offset 0x044 ................................................................ 1081
CAN IF1 Data B2 (CANIF1DB2), offset 0x048 ................................................................ 1081
CAN IF2 Data A1 (CANIF2DA1), offset 0x09C ............................................................... 1081
CAN IF2 Data A2 (CANIF2DA2), offset 0x0A0 ............................................................... 1081
CAN IF2 Data B1 (CANIF2DB1), offset 0x0A4 ............................................................... 1081
CAN IF2 Data B2 (CANIF2DB2), offset 0x0A8 ............................................................... 1081
CAN Transmission Request 1 (CANTXRQ1), offset 0x100 .............................................. 1082
CAN Transmission Request 2 (CANTXRQ2), offset 0x104 .............................................. 1082
CAN New Data 1 (CANNWDA1), offset 0x120 ............................................................... 1083
CAN New Data 2 (CANNWDA2), offset 0x124 ............................................................... 1083
CAN Message 1 Interrupt Pending (CANMSG1INT), offset 0x140 ................................... 1084
CAN Message 2 Interrupt Pending (CANMSG2INT), offset 0x144 ................................... 1084
CAN Message 1 Valid (CANMSG1VAL), offset 0x160 ..................................................... 1085
CAN Message 2 Valid (CANMSG2VAL), offset 0x164 ..................................................... 1085
Analog Comparators ................................................................................................................. 1086
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Analog Comparator Masked Interrupt Status (ACMIS), offset 0x000 ................................ 1093
Analog Comparator Raw Interrupt Status (ACRIS), offset 0x004 ..................................... 1094
Analog Comparator Interrupt Enable (ACINTEN), offset 0x008 ....................................... 1095
Analog Comparator Reference Voltage Control (ACREFCTL), offset 0x010 ..................... 1096
Analog Comparator Status 0 (ACSTAT0), offset 0x020 ................................................... 1097
Analog Comparator Status 1 (ACSTAT1), offset 0x040 ................................................... 1097
Analog Comparator Control 0 (ACCTL0), offset 0x024 ................................................... 1098
Analog Comparator Control 1 (ACCTL1), offset 0x044 ................................................... 1098
Analog Comparator Peripheral Properties (ACMPPP), offset 0xFC0 ................................ 1100
Pulse Width Modulator (PWM) .................................................................................................. 1101
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
Register 12:
Register 13:
Register 14:
Register 15:
Register 16:
Register 17:
Register 18:
PWM Master Control (PWMCTL), offset 0x000 .............................................................. 1115
PWM Time Base Sync (PWMSYNC), offset 0x004 ......................................................... 1117
PWM Output Enable (PWMENABLE), offset 0x008 ........................................................ 1118
PWM Output Inversion (PWMINVERT), offset 0x00C ..................................................... 1120
PWM Output Fault (PWMFAULT), offset 0x010 .............................................................. 1122
PWM Interrupt Enable (PWMINTEN), offset 0x014 ......................................................... 1124
PWM Raw Interrupt Status (PWMRIS), offset 0x018 ...................................................... 1126
PWM Interrupt Status and Clear (PWMISC), offset 0x01C .............................................. 1128
PWM Status (PWMSTATUS), offset 0x020 .................................................................... 1130
PWM Fault Condition Value (PWMFAULTVAL), offset 0x024 ........................................... 1131
PWM Enable Update (PWMENUPD), offset 0x028 ......................................................... 1133
PWM0 Control (PWM0CTL), offset 0x040 ...................................................................... 1137
PWM1 Control (PWM1CTL), offset 0x080 ...................................................................... 1137
PWM2 Control (PWM2CTL), offset 0x0C0 ..................................................................... 1137
PWM3 Control (PWM3CTL), offset 0x100 ...................................................................... 1137
PWM0 Interrupt and Trigger Enable (PWM0INTEN), offset 0x044 ................................... 1142
PWM1 Interrupt and Trigger Enable (PWM1INTEN), offset 0x084 ................................... 1142
PWM2 Interrupt and Trigger Enable (PWM2INTEN), offset 0x0C4 ................................... 1142
June 12, 2014
31
Texas Instruments-Production Data
Table of Contents
Register 19:
Register 20:
Register 21:
Register 22:
Register 23:
Register 24:
Register 25:
Register 26:
Register 27:
Register 28:
Register 29:
Register 30:
Register 31:
Register 32:
Register 33:
Register 34:
Register 35:
Register 36:
Register 37:
Register 38:
Register 39:
Register 40:
Register 41:
Register 42:
Register 43:
Register 44:
Register 45:
Register 46:
Register 47:
Register 48:
Register 49:
Register 50:
Register 51:
Register 52:
Register 53:
Register 54:
Register 55:
Register 56:
Register 57:
Register 58:
Register 59:
Register 60:
Register 61:
Register 62:
Register 63:
Register 64:
Register 65:
Register 66:
PWM3 Interrupt and Trigger Enable (PWM3INTEN), offset 0x104 ................................... 1142
PWM0 Raw Interrupt Status (PWM0RIS), offset 0x048 ................................................... 1145
PWM1 Raw Interrupt Status (PWM1RIS), offset 0x088 ................................................... 1145
PWM2 Raw Interrupt Status (PWM2RIS), offset 0x0C8 .................................................. 1145
PWM3 Raw Interrupt Status (PWM3RIS), offset 0x108 ................................................... 1145
PWM0 Interrupt Status and Clear (PWM0ISC), offset 0x04C .......................................... 1147
PWM1 Interrupt Status and Clear (PWM1ISC), offset 0x08C .......................................... 1147
PWM2 Interrupt Status and Clear (PWM2ISC), offset 0x0CC .......................................... 1147
PWM3 Interrupt Status and Clear (PWM3ISC), offset 0x10C .......................................... 1147
PWM0 Load (PWM0LOAD), offset 0x050 ...................................................................... 1149
PWM1 Load (PWM1LOAD), offset 0x090 ...................................................................... 1149
PWM2 Load (PWM2LOAD), offset 0x0D0 ...................................................................... 1149
PWM3 Load (PWM3LOAD), offset 0x110 ...................................................................... 1149
PWM0 Counter (PWM0COUNT), offset 0x054 ............................................................... 1150
PWM1 Counter (PWM1COUNT), offset 0x094 ............................................................... 1150
PWM2 Counter (PWM2COUNT), offset 0x0D4 .............................................................. 1150
PWM3 Counter (PWM3COUNT), offset 0x114 ............................................................... 1150
PWM0 Compare A (PWM0CMPA), offset 0x058 ............................................................ 1151
PWM1 Compare A (PWM1CMPA), offset 0x098 ............................................................ 1151
PWM2 Compare A (PWM2CMPA), offset 0x0D8 ............................................................ 1151
PWM3 Compare A (PWM3CMPA), offset 0x118 ............................................................. 1151
PWM0 Compare B (PWM0CMPB), offset 0x05C ............................................................ 1152
PWM1 Compare B (PWM1CMPB), offset 0x09C ............................................................ 1152
PWM2 Compare B (PWM2CMPB), offset 0x0DC ........................................................... 1152
PWM3 Compare B (PWM3CMPB), offset 0x11C ............................................................ 1152
PWM0 Generator A Control (PWM0GENA), offset 0x060 ............................................... 1153
PWM1 Generator A Control (PWM1GENA), offset 0x0A0 ............................................... 1153
PWM2 Generator A Control (PWM2GENA), offset 0x0E0 ............................................... 1153
PWM3 Generator A Control (PWM3GENA), offset 0x120 ............................................... 1153
PWM0 Generator B Control (PWM0GENB), offset 0x064 ............................................... 1156
PWM1 Generator B Control (PWM1GENB), offset 0x0A4 ............................................... 1156
PWM2 Generator B Control (PWM2GENB), offset 0x0E4 ............................................... 1156
PWM3 Generator B Control (PWM3GENB), offset 0x124 ............................................... 1156
PWM0 Dead-Band Control (PWM0DBCTL), offset 0x068 ............................................... 1159
PWM1 Dead-Band Control (PWM1DBCTL), offset 0x0A8 ............................................... 1159
PWM2 Dead-Band Control (PWM2DBCTL), offset 0x0E8 ............................................... 1159
PWM3 Dead-Band Control (PWM3DBCTL), offset 0x128 ............................................... 1159
PWM0 Dead-Band Rising-Edge Delay (PWM0DBRISE), offset 0x06C ............................ 1160
PWM1 Dead-Band Rising-Edge Delay (PWM1DBRISE), offset 0x0AC ............................ 1160
PWM2 Dead-Band Rising-Edge Delay (PWM2DBRISE), offset 0x0EC ............................ 1160
PWM3 Dead-Band Rising-Edge Delay (PWM3DBRISE), offset 0x12C ............................ 1160
PWM0 Dead-Band Falling-Edge-Delay (PWM0DBFALL), offset 0x070 ............................ 1161
PWM1 Dead-Band Falling-Edge-Delay (PWM1DBFALL), offset 0x0B0 ............................ 1161
PWM2 Dead-Band Falling-Edge-Delay (PWM2DBFALL), offset 0x0F0 ............................ 1161
PWM3 Dead-Band Falling-Edge-Delay (PWM3DBFALL), offset 0x130 ............................ 1161
PWM0 Fault Source 0 (PWM0FLTSRC0), offset 0x074 .................................................. 1162
PWM1 Fault Source 0 (PWM1FLTSRC0), offset 0x0B4 .................................................. 1162
PWM2 Fault Source 0 (PWM2FLTSRC0), offset 0x0F4 .................................................. 1162
32
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 67:
Register 68:
Register 69:
Register 70:
Register 71:
Register 72:
Register 73:
Register 74:
Register 75:
Register 76:
Register 77:
Register 78:
Register 79:
Register 80:
Register 81:
Register 82:
Register 83:
Register 84:
Register 85:
Register 86:
PWM3 Fault Source 0 (PWM3FLTSRC0), offset 0x134 .................................................. 1162
PWM0 Fault Source 1 (PWM0FLTSRC1), offset 0x078 .................................................. 1164
PWM1 Fault Source 1 (PWM1FLTSRC1), offset 0x0B8 .................................................. 1164
PWM2 Fault Source 1 (PWM2FLTSRC1), offset 0x0F8 .................................................. 1164
PWM3 Fault Source 1 (PWM3FLTSRC1), offset 0x138 .................................................. 1164
PWM0 Minimum Fault Period (PWM0MINFLTPER), offset 0x07C ................................... 1167
PWM1 Minimum Fault Period (PWM1MINFLTPER), offset 0x0BC ................................... 1167
PWM2 Minimum Fault Period (PWM2MINFLTPER), offset 0x0FC ................................... 1167
PWM3 Minimum Fault Period (PWM3MINFLTPER), offset 0x13C ................................... 1167
PWM0 Fault Pin Logic Sense (PWM0FLTSEN), offset 0x800 .......................................... 1168
PWM1 Fault Pin Logic Sense (PWM1FLTSEN), offset 0x880 .......................................... 1168
PWM0 Fault Status 0 (PWM0FLTSTAT0), offset 0x804 ................................................... 1169
PWM1 Fault Status 0 (PWM1FLTSTAT0), offset 0x884 ................................................... 1169
PWM2 Fault Status 0 (PWM2FLTSTAT0), offset 0x904 ................................................... 1169
PWM3 Fault Status 0 (PWM3FLTSTAT0), offset 0x984 ................................................... 1169
PWM0 Fault Status 1 (PWM0FLTSTAT1), offset 0x808 ................................................... 1171
PWM1 Fault Status 1 (PWM1FLTSTAT1), offset 0x888 ................................................... 1171
PWM2 Fault Status 1 (PWM2FLTSTAT1), offset 0x908 ................................................... 1171
PWM3 Fault Status 1 (PWM3FLTSTAT1), offset 0x988 ................................................... 1171
PWM Peripheral Properties (PWMPP), offset 0xFC0 ...................................................... 1174
Quadrature Encoder Interface (QEI) ........................................................................................ 1176
Register 1:
Register 2:
Register 3:
Register 4:
Register 5:
Register 6:
Register 7:
Register 8:
Register 9:
Register 10:
Register 11:
QEI Control (QEICTL), offset 0x000 ..............................................................................
QEI Status (QEISTAT), offset 0x004 ..............................................................................
QEI Position (QEIPOS), offset 0x008 ............................................................................
QEI Maximum Position (QEIMAXPOS), offset 0x00C .....................................................
QEI Timer Load (QEILOAD), offset 0x010 .....................................................................
QEI Timer (QEITIME), offset 0x014 ...............................................................................
QEI Velocity Counter (QEICOUNT), offset 0x018 ...........................................................
QEI Velocity (QEISPEED), offset 0x01C ........................................................................
QEI Interrupt Enable (QEIINTEN), offset 0x020 .............................................................
QEI Raw Interrupt Status (QEIRIS), offset 0x024 ...........................................................
QEI Interrupt Status and Clear (QEIISC), offset 0x028 ...................................................
June 12, 2014
1183
1186
1187
1188
1189
1190
1191
1192
1193
1195
1197
33
Texas Instruments-Production Data
Revision History
Revision History
The revision history table notes changes made between the indicated revisions of the
TM4C123BE6PM data sheet.
Table 1. Revision History
Date
June 2014
March 2014
November 2013
Revision
Description
15842.2741 ■
In System Control Chapter, corrected description for MINSYSDIV bitfield in Device Capabilities 1
(DC1) legacy register.
■
In Timers chapter, removed erroneous references to TCACT bit field.
■
In SSI chapter, corrected that during idle periods the transmit data line SSInTx is tristated.
■
In Package Information appendix:
– Corrected Key to Part Numbers diagram.
– Moved Orderable Part Numbers table to addendum.
– Deleted Packaging Materials section and put into separate packaging document.
■
Additional minor data sheet clarifications and corrections.
15741.2722 ■
In the Internal Memory chapter, in the EEPROM section:
– Added section on soft reset handling.
– Added important information on EEPROM initialization and configuration.
■
In the DMA chapter, added information regarding interrupts and transfers from the UART or SSI
modules.
■
In the Hibernation chapter, noted that the EXTW bit is set in the HIBRIS register regardless of the
PINWEN setting in the HIBCTL register.
■
In the GPIO chapter:
– Corrected table GPIO Pins with Special Considerations.
– Added information on preventing false interrupts.
– Corrected GPIOAMSEL register to be 8 bits.
■
In the Timer chapter:
– Clarified initialization and configuration for Input-Edge Count mode.
– Clarified behavior of TnMIE and TnCINTD bits in the GPTM Timer n Mode (GPTMTnMR)
register.
■
In the Electrical Characteristics chapter:
– In table Reset Characteristics, clarified internal reset time parameter values.
– In table Hibernation Oscillator Input Characteristics, added parameter CINSE Input capacitance.
– In tables Hibernation Oscillator Input Characteristics and Main Oscillator Input Characteristics,
removed parameter C0 Crystal shunt capacitance.
– Updated table Crystal Parameters.
– In table GPIO Module Characteristics, added parameter CGPIO GPIO Digital Input Capacitance.
– Added table PWM Timing Characteristics.
■
In the Package Information appendix:
– Updated Orderable Devices section to reflect silicon revision 7 part numbers.
– Added Tape and Reel pin 1 location.
■
Additional minor data sheet clarifications and corrections.
15553.2700 ■
■
In System Control chapter, clarified PIOSC features and accuracy.
In Hibernation Module chapter:
34
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 1. Revision History (continued)
Date
Revision
Description
Corrected figures "Using a Crystal as the Hibernation Clock Source with a Single Battery Source"
and "Using a Regulator for Both VDD and VBAT".
–
Replaced RTC Trim tables with two new figures "Counter Behavior with a TRIM Value of 0x8002"
and "Counter Behavior with a TRIM Value of 0x7FFC".
–
Clarified Hibernation Data (HIBDATA) register description.
■
In Watchdog Timers chapter, clarified Watchdog Control (WDTCTL) register description.
■
In ADC chapter:
–
Clarified functionality when using an ADC digital comparator as a fault source.
–
Clarified signals used for ADC voltage reference.
–
Clarified ADC Trigger Source Select (ADCTSSEL) register description.
–
Corrected VREF bit in ADC Control (ADCCTL) register from 2-bit field [1:0] to 1-bit field [0].
■
In UART chapter, clarified DMA operation.
■
In SSI chapter:
–
Corrected timing guidelines in figures "Freescale SPI Frame Format (Continuous Transfer) with
SPO=1 and SPH=0" and "Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0".
–
Clarified SSI Initialization and Configuration.
–
Corrected bit 3 in SSI Control 1 (SSICR1) register from SOD (SSI Slave Mode Output Disable)
to reserved.
■
In PWM chapter, added clarifications to PWM0 Control (PWM0CTL), PWM0 Interrupt Status and
Clear (PWM0ISC), PWM0 Counter (PWM0COUNT), PWM0 Fault Status 0 (PWM0FLTSTAT0),
and PWM0 Fault Status 1 (PWM0FLTSTAT1) registers.
■
In Signal Tables chapter:
■
■
July 16, 2013
–
15033.2672 ■
–
In Unused Signals table, corrected preferred and acceptable practices for RST pin.
–
Clarified GNDX pin description.
In Electrical Characteristics chapter:
–
In Power-On and Brown-Out Levels table, corrected TVDDC_RISE parameter min and max values.
–
In PIOSC Clock Characteristics table, clarified FPIOSC parameter values by defining values for
both factory calibration and recalibration. Also added PIOSC startup time parameter to table.
–
In Main Oscillator Specifications section, corrected minimum value for External load capacitance
on OSC0, OSC1 pins. Also added two 25-MHz crystals to Crystal Parameters table.
–
Corrected figure "Master Mode SSI Timing for SPI Frame Format (FRF=00), with SPH=1".
–
In I2C Characteristics table, clarified TDH data hold time parameter values by defining values
for both slave and master. In addition, added parameter I10 TDV data valid.
–
Modified figure "I2C Timing" to add new parameter I10.
In Packaging Information appendix, added Packaging Materials figures.
In the Electrical Characteristics chapter:
June 12, 2014
35
Texas Instruments-Production Data
Revision History
Table 1. Revision History (continued)
Date
Revision
Description
■
July 2013
14995.2667 ■
–
Added maximum junction temperature to Maximum Ratings table. Also moved Unpowered
storage temperature range parameter to this table.
–
In SSI Characteristics table, corrected values for TRXDMS, TRXDMH, and TRXDSSU. Also clarified
footnotes to table.
–
Corrected parameter numbers in figures "Master Mode SSI Timing for SPI Frame Format
(FRF=00), with SPH=1" and "Slave Mode SSI Timing for SPI Frame Format (FRF=00), with
SPH=1".
Additional minor data sheet clarifications and corrections.
Deleted erroneous references to the PWM Peripheral Configuration (PWMPC) register.
■
In the System Control chapter, corrected resets for bits [7:4] in System Properties (SYSPROP)
register.
■
In the Hibernation Module chapter:
–
Corrected figures "Using a Crystal as the Hibernation Clock Source with a Single Battery Source"
and "Using a Dedicated Oscillator as the Hibernation Clock Source with VDD3ON Mode".
–
Clarified when the Hibernation module can generate interrupts.
■
In the Internal Memory chapter, removed the INVPL bit from the EEPROM Done Status (EEDONE)
register.
■
In the uDMA chapter, in the µDMA Channel Assignments table, corrected names of timers 6-11 to
wide timers 0-5.
■
In the Timers chapter:
–
Clarified that the timer must be configured for one-shot or periodic time-out mode to produce
an ADC trigger assertion and that the GPTM does not generate triggers for match, compare
events or compare match events.
–
Added a step in the RTC Mode initialization and configuration: If the timer has been operating
in a different mode prior to this, clear any residual set bits in the GPTM Timer n Mode
(GPTMTnMR) register before reconfiguring.
■
In the Watchdog Timer chapter, added a note that locking the watchdog registers using the
WDTLOCK register does not affect the WDTICR register and allows interrupts to always be serviced.
■
In the SSI chapter, clarified note in Bit Rate Generation section to indicate that the System Clock
or the PIOSC can be used as the source for SSIClk. Also corrected to indicate maximum SSIClk
limit in SSI slave mode as well as the fact that SYSCLK has to be at least 12 times that of SSICLk.
■
In the PWM chapter, clarified that the PWM has two clock sources, selected by the USPWMDIV bit
in the Run-Mode Clock Configuration (RCC) register.
■
In the QEI chapter, noted that the INTERROR bit is only applicable when the QEI is operating in
quadrature phase mode (SIGMODE=0) and should be masked when SIGMODE=1. Similarly, the
INTDIR bit is only applicable when the QEI is operating in clock/direction mode (SIGMODE=1) and
should be masked when SIGMODE=0.
■
In the Electrical Characteristics chapter:
–
Moved Maximum Ratings and ESD Absolute Maximum Ratings to the front of the chapter.
–
Added VBATRMP parameter to Maximum Ratings and Hibernation Module Battery Characteristics
tables.
36
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 1. Revision History (continued)
Date
Revision
Description
–
Added ambient and junction temperatures to Temperature Characteristics table and clarified
values in Thermal Characteristics table.
–
Added clarifying footnote to VVDD_POK parameter in Power-On and Brown-Out Levels table.
–
In the Flash Memory and EEPROM Characteristics tables, added a parameter for page/mass
erase times for 10k cycles and corrected existing values for all page and mass erase parameters.
–
Corrected DNL max value in ADC Electrical Characteristics table.
–
In the SSI Characteristics table, changed parameter names for S7-S14, provided a max number
instead of a min for S7, and corrected values for S9-S14.
–
Replaced figure "SSI Timing for SPI Frame Format (FRF=00), with SPH=1" with two figures,
one for Master Mode and one for Slave Mode.
–
Updated and added values to the table Table 23-40 on page 1266.
■
In the Package Information appendix, moved orderable devices table from addendum to appendix,
clarified part markings and moved packaging diagram from addendum to appendix.
■
Additional minor data sheet clarifications and corrections.
June 12, 2014
37
Texas Instruments-Production Data
About This Document
About This Document
This data sheet provides reference information for the TM4C123BE6PM microcontroller, describing
the functional blocks of the system-on-chip (SoC) device designed around the ARM® Cortex™-M4F
core.
Audience
This manual is intended for system software developers, hardware designers, and application
developers.
About This Manual
This document is organized into sections that correspond to each major feature.
Related Documents
The following related documents are available on the Tiva™ C Series web site at
http://www.ti.com/tiva-c:
■ Tiva™ C Series TM4C123x Silicon Errata (literature number SPMZ849)
■ TivaWare™ Boot Loader for C Series User's Guide (literature number SPMU301)
■ TivaWare™ Graphics Library for C Series User's Guide (literature number SPMU300)
■ TivaWare™ for C Series Release Notes (literature number SPMU299)
■ TivaWare™ Peripheral Driver Library for C Series User's Guide (literature number SPMU298)
■ TivaWare™ USB Library for C Series User's Guide (literature number SPMU297)
■ Tiva™ C Series TM4C123x ROM User’s Guide (literature number SPMU367)
The following related documents may also be useful:
■ ARM® Cortex™-M4 Errata (literature number SPMZ637)
■ ARM® Cortex™-M4 Technical Reference Manual
■ ARM® Debug Interface V5 Architecture Specification
■ ARM® Embedded Trace Macrocell Architecture Specification
■ Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide
(literature number ARM DUI 0553A)
■ IEEE Standard 1149.1-Test Access Port and Boundary-Scan Architecture
This documentation list was current as of publication date. Please check the web site for additional
documentation, including application notes and white papers.
38
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Documentation Conventions
This document uses the conventions shown in Table 2 on page 39.
Table 2. Documentation Conventions
Notation
Meaning
General Register Notation
REGISTER
APB registers are indicated in uppercase bold. For example, PBORCTL is the Power-On and
Brown-Out Reset Control register. If a register name contains a lowercase n, it represents more
than one register. For example, SRCRn represents any (or all) of the three Software Reset Control
registers: SRCR0, SRCR1 , and SRCR2.
bit
A single bit in a register.
bit field
Two or more consecutive and related bits.
offset 0xnnn
A hexadecimal increment to a register's address, relative to that module's base address as specified
in Table 2-4 on page 87.
Register N
Registers are numbered consecutively throughout the document to aid in referencing them. The
register number has no meaning to software.
reserved
Register bits marked reserved are reserved for future use. In most cases, reserved bits are set to
0; however, user software should not rely on the value of a reserved bit. To provide software
compatibility with future products, the value of a reserved bit should be preserved across a
read-modify-write operation.
yy:xx
The range of register bits inclusive from xx to yy. For example, 31:15 means bits 15 through 31 in
that register.
Register Bit/Field
Types
This value in the register bit diagram indicates whether software running on the controller can
change the value of the bit field.
RC
Software can read this field. The bit or field is cleared by hardware after reading the bit/field.
RO
Software can read this field. Always write the chip reset value.
RW
Software can read or write this field.
RWC
Software can read or write this field. Writing to it with any value clears the register.
RW1C
Software can read or write this field. A write of a 0 to a W1C bit does not affect the bit value in the
register. A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged.
This register type is primarily used for clearing interrupt status bits where the read operation provides
the interrupt status and the write of the read value clears only the interrupts being reported at the
time the register was read.
RW1S
Software can read or write a 1 to this field. A write of a 0 to a RW1S bit does not affect the bit value
in the register.
W1C
Software can write this field. A write of a 0 to a W1C bit does not affect the bit value in the register.
A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged. A
read of the register returns no meaningful data.
This register is typically used to clear the corresponding bit in an interrupt register.
WO
Only a write by software is valid; a read of the register returns no meaningful data.
Register Bit/Field
Reset Value
This value in the register bit diagram shows the bit/field value after any reset, unless noted.
0
Bit cleared to 0 on chip reset.
1
Bit set to 1 on chip reset.
-
Nondeterministic.
Pin/Signal Notation
[]
Pin alternate function; a pin defaults to the signal without the brackets.
pin
Refers to the physical connection on the package.
signal
Refers to the electrical signal encoding of a pin.
June 12, 2014
39
Texas Instruments-Production Data
About This Document
Table 2. Documentation Conventions (continued)
Notation
Meaning
assert a signal
Change the value of the signal from the logically False state to the logically True state. For active
High signals, the asserted signal value is 1 (High); for active Low signals, the asserted signal value
is 0 (Low). The active polarity (High or Low) is defined by the signal name (see SIGNAL and SIGNAL
below).
deassert a signal
Change the value of the signal from the logically True state to the logically False state.
SIGNAL
Signal names are in uppercase and in the Courier font. An overbar on a signal name indicates that
it is active Low. To assert SIGNAL is to drive it Low; to deassert SIGNAL is to drive it High.
SIGNAL
Signal names are in uppercase and in the Courier font. An active High signal has no overbar. To
assert SIGNAL is to drive it High; to deassert SIGNAL is to drive it Low.
Numbers
X
An uppercase X indicates any of several values is allowed, where X can be any legal pattern. For
example, a binary value of 0X00 can be either 0100 or 0000, a hex value of 0xX is 0x0 or 0x1, and
so on.
0x
Hexadecimal numbers have a prefix of 0x. For example, 0x00FF is the hexadecimal number FF.
All other numbers within register tables are assumed to be binary. Within conceptual information,
binary numbers are indicated with a b suffix, for example, 1011b, and decimal numbers are written
without a prefix or suffix.
40
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
1
Architectural Overview
®
Texas Instrument's Tiva™ C Series microcontrollers provide designers a high-performance ARM
Cortex™-M-based architecture with a broad set of integration capabilities and a strong ecosystem
of software and development tools. Targeting performance and flexibility, the Tiva™ C Series
architecture offers a 80 MHz Cortex-M with FPU, a variety of integrated memories and multiple
programmable GPIO. Tiva™ C Series devices offer consumers compelling cost-effective solutions
by integrating application-specific peripherals and providing a comprehensive library of software
tools which minimize board costs and design-cycle time. Offering quicker time-to-market and cost
savings, the Tiva™ C Series microcontrollers are the leading choice in high-performance 32-bit
applications.
This chapter contains an overview of the Tiva™ C Series microcontrollers as well as details on the
TM4C123BE6PM microcontroller:
■
■
■
■
■
■
1.1
“Tiva™ C Series Overview” on page 41
“TM4C123BE6PM Microcontroller Overview” on page 42
“TM4C123BE6PM Microcontroller Features” on page 45
“TM4C123BE6PM Microcontroller Hardware Details” on page 63
“Kits” on page 63
“Support Information” on page 63
Tiva™ C Series Overview
The Tiva™ C Series ARM Cortex-M4 microcontrollers provide top performance and advanced
integration. The product family is positioned for cost-conscious applications requiring significant
control processing and connectivity capabilities such as:
■
■
■
■
■
■
■
■
■
■
■
Low power, hand-held smart devices
Gaming equipment
Home and commercial site monitoring and control
Motion control
Medical instrumentation
Test and measurement equipment
Factory automation
Fire and security
Smart Energy/Smart Grid solutions
Intelligent lighting control
Transportation
For applications requiring extreme conservation of power, the TM4C123BE6PM microcontroller
features a battery-backed Hibernation module to efficiently power down the TM4C123BE6PM to a
low-power state during extended periods of inactivity. With a power-up/power-down sequencer, a
real-time counter (RTC), multiple wake-from-hibernate options, and dedicated battery-backed
memory, the Hibernation module positions the TM4C123BE6PM microcontroller perfectly for battery
applications.
In addition, the TM4C123BE6PM microcontroller offers the advantages of ARM's widely available
development tools, System-on-Chip (SoC) infrastructure IP applications, and a large user community.
Additionally, the microcontroller uses ARM's Thumb®-compatible Thumb-2 instruction set to reduce
memory requirements and, thereby, cost. Finally, much of the TM4C123BE6PM microcontroller
code is compatible to the Tiva™ C Series product line, providing flexibility across designs.
June 12, 2014
41
Texas Instruments-Production Data
Architectural Overview
Texas Instruments offers a complete solution to get to market quickly, with evaluation and
development boards, white papers and application notes, an easy-to-use peripheral driver library,
and a strong support, sales, and distributor network.
1.2
TM4C123BE6PM Microcontroller Overview
The TM4C123BE6PM microcontroller combines complex integration and high performance with the
features shown in Table 1-1.
Table 1-1. TM4C123BE6PM Microcontroller Features
Feature
Description
Performance
Core
ARM Cortex-M4F processor core
Performance
80-MHz operation; 100 DMIPS performance
Flash
128 KB single-cycle Flash memory
System SRAM
32 KB single-cycle SRAM
EEPROM
2KB of EEPROM
Internal ROM
Internal ROM loaded with TivaWare™ for C Series software
Security
Communication Interfaces
Universal Asynchronous Receivers/Transmitter (UART) Eight UARTs
Synchronous Serial Interface (SSI)
Four SSI modules
Inter-Integrated Circuit (I2C)
Four I2C modules with four transmission speeds including high-speed
mode
Controller Area Network (CAN)
Two CAN 2.0 A/B controllers
System Integration
Micro Direct Memory Access (µDMA)
ARM® PrimeCell® 32-channel configurable μDMA controller
General-Purpose Timer (GPTM)
Six 16/32-bit GPTM blocks and six 32/64-bit Wide GPTM blocks
Watchdog Timer (WDT)
Two watchdog timers
Hibernation Module (HIB)
Low-power battery-backed Hibernation module
General-Purpose Input/Output (GPIO)
Six physical GPIO blocks
Advanced Motion Control
Pulse Width Modulator (PWM)
Two PWM modules, each with four PWM generator blocks and a
control block, for a total of 16 PWM outputs.
Quadrature Encoder Interface (QEI)
Two QEI modules
Analog Support
Analog-to-Digital Converter (ADC)
Two 12-bit ADC modules, each with a maximum sample rate of one
million samples/second
Analog Comparator Controller
Two independent integrated analog comparators
Digital Comparator
16 digital comparators
JTAG and Serial Wire Debug (SWD)
One JTAG module with integrated ARM SWD
Package Information
Package
64-pin LQFP
Operating Range (Ambient)
Industrial (-40°C to 85°C) temperature range
Figure 1-1 on page 44 shows the features on the TM4C123BE6PM microcontroller. Note that there
are two on-chip buses that connect the core to the peripherals. The Advanced Peripheral Bus (APB)
42
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
bus is the legacy bus. The Advanced High-Performance Bus (AHB) bus provides better back-to-back
access performance than the APB bus.
June 12, 2014
43
Texas Instruments-Production Data
Architectural Overview
Figure 1-1. Tiva™ TM4C123BE6PM Microcontroller High-Level Block Diagram
JTAG/SWD
ARM®
Cortex™-M4F
ROM
(80MHz)
System
Control and
Clocks
(w/ Precis. Osc.)
ETM
FPU
NVIC
MPU
DCode bus
Boot Loader
DriverLib
AES & CRC
Flash
(128KB)
ICode bus
System Bus
TM4C123BE6PM
Bus Matrix
SRAM
(32KB)
SYSTEM PERIPHERALS
EEPROM
(2K)
Hibernation
Module
GPIOs
(43)
GeneralPurpose
Timer (12)
I2C
(4)
CAN
Controller
(2)
Analog
Comparator
(2)
Advanced Peripheral Bus (APB)
Watchdog
Timer
(2)
Advanced High-Performance Bus (AHB)
DMA
SERIAL PERIPHERALS
UART
(8)
SSI
(4)
ANALOG PERIPHERALS
12- Bit ADC
Channels
(12)
MOTION CONTROL PERIPHERALS
PWM
(16)
QEI
(2)
44
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
1.3
TM4C123BE6PM Microcontroller Features
The TM4C123BE6PM microcontroller component features and general function are discussed in
more detail in the following section.
1.3.1
ARM Cortex-M4F Processor Core
All members of the Tiva™ C Series, including the TM4C123BE6PM microcontroller, are designed
around an ARM Cortex-M processor core. The ARM Cortex-M processor provides the core for a
high-performance, low-cost platform that meets the needs of minimal memory implementation,
reduced pin count, and low power consumption, while delivering outstanding computational
performance and exceptional system response to interrupts.
1.3.1.1
Processor Core (see page 64)
■ 32-bit ARM Cortex-M4F architecture optimized for small-footprint embedded applications
■ 80-MHz operation; 100 DMIPS performance
■ Outstanding processing performance combined with fast interrupt handling
■ Thumb-2 mixed 16-/32-bit instruction set delivers the high performance expected of a 32-bit
ARM core in a compact memory size usually associated with 8- and 16-bit devices, typically in
the range of a few kilobytes of memory for microcontroller-class applications
– Single-cycle multiply instruction and hardware divide
– Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined
peripheral control
– Unaligned data access, enabling data to be efficiently packed into memory
■ IEEE754-compliant single-precision Floating-Point Unit (FPU)
■ 16-bit SIMD vector processing unit
■ Fast code execution permits slower processor clock or increases sleep mode time
■ Harvard architecture characterized by separate buses for instruction and data
■ Efficient processor core, system and memories
■ Hardware division and fast digital-signal-processing orientated multiply accumulate
■ Saturating arithmetic for signal processing
■ Deterministic, high-performance interrupt handling for time-critical applications
■ Memory protection unit (MPU) to provide a privileged mode for protected operating system
functionality
■ Enhanced system debug with extensive breakpoint and trace capabilities
■ Serial Wire Debug and Serial Wire Trace reduce the number of pins required for debugging and
tracing
June 12, 2014
45
Texas Instruments-Production Data
Architectural Overview
■ Migration from the ARM7™ processor family for better performance and power efficiency
■ Optimized for single-cycle Flash memory usage up to specific frequencies; see “Internal
Memory” on page 512 for more information.
■ Ultra-low power consumption with integrated sleep modes
1.3.1.2
System Timer (SysTick) (see page 118)
ARM Cortex-M4F includes an integrated system timer, SysTick. SysTick provides a simple, 24-bit,
clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter
can be used in several different ways, for example:
■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick
routine
■ A high-speed alarm timer using the system clock
■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock
used and the dynamic range of the counter
■ A simple counter used to measure time to completion and time used
■ An internal clock-source control based on missing/meeting durations
1.3.1.3
Nested Vectored Interrupt Controller (NVIC) (see page 119)
The TM4C123BE6PM controller includes the ARM Nested Vectored Interrupt Controller (NVIC).
The NVIC and Cortex-M4F prioritize and handle all exceptions in Handler Mode. The processor
state is automatically stored to the stack on an exception and automatically restored from the stack
at the end of the Interrupt Service Routine (ISR). The interrupt vector is fetched in parallel to the
state saving, enabling efficient interrupt entry. The processor supports tail-chaining, meaning that
back-to-back interrupts can be performed without the overhead of state saving and restoration.
Software can set eight priority levels on 7 exceptions (system handlers) and 77 interrupts.
■ Deterministic, fast interrupt processing: always 12 cycles, or just 6 cycles with tail-chaining (these
values reflect no FPU stacking)
■ External non-maskable interrupt signal (NMI) available for immediate execution of NMI handler
for safety critical applications
■ Dynamically reprioritizable interrupts
■ Exceptional interrupt handling via hardware implementation of required register manipulations
1.3.1.4
System Control Block (SCB) (see page 120)
The SCB provides system implementation information and system control, including configuration,
control, and reporting of system exceptions.
1.3.1.5
Memory Protection Unit (MPU) (see page 120)
The MPU supports the standard ARM7 Protected Memory System Architecture (PMSA) model. The
MPU provides full support for protection regions, overlapping protection regions, access permissions,
and exporting memory attributes to the system.
46
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
1.3.1.6
Floating-Point Unit (FPU) (see page 125)
The FPU fully supports single-precision add, subtract, multiply, divide, multiply and accumulate,
and square root operations. It also provides conversions between fixed-point and floating-point data
formats, and floating-point constant instructions.
■ 32-bit instructions for single-precision (C float) data-processing operations
■ Combined multiply and accumulate instructions for increased precision (Fused MAC)
■ Hardware support for conversion, addition, subtraction, multiplication with optional accumulate,
division, and square-root
■ Hardware support for denormals and all IEEE rounding modes
■ 32 dedicated 32-bit single-precision registers, also addressable as 16 double-word registers
■ Decoupled three stage pipeline
1.3.2
On-Chip Memory
The TM4C123BE6PM microcontroller is integrated with the following set of on-chip memory and
features:
■ 32 KB single-cycle SRAM
■ 128 KB Flash memory
■ 2KB EEPROM
■ Internal ROM loaded with TivaWare™ for C Series software:
– TivaWare™ Peripheral Driver Library
– TivaWare Boot Loader
– Advanced Encryption Standard (AES) cryptography tables
– Cyclic Redundancy Check (CRC) error detection functionality
1.3.2.1
SRAM (see page 513)
The TM4C123BE6PM microcontroller provides 32 KB of single-cycle on-chip SRAM. The internal
SRAM of the device is located at offset 0x2000.0000 of the device memory map.
Because read-modify-write (RMW) operations are very time consuming, ARM has introduced
bit-banding technology in the Cortex-M4F processor. With a bit-band-enabled processor, certain
regions in the memory map (SRAM and peripheral space) can use address aliases to access
individual bits in a single, atomic operation.
Data can be transferred to and from SRAM by the following masters:
■ µDMA
1.3.2.2
Flash Memory (see page 516)
The TM4C123BE6PM microcontroller provides 128 KB of single-cycle on-chip Flash memory. The
Flash memory is organized as a set of 1-KB blocks that can be individually erased. Erasing a block
causes the entire contents of the block to be reset to all 1s. These blocks are paired into a set of
2-KB blocks that can be individually protected. The blocks can be marked as read-only or
execute-only, providing different levels of code protection. Read-only blocks cannot be erased or
June 12, 2014
47
Texas Instruments-Production Data
Architectural Overview
programmed, protecting the contents of those blocks from being modified. Execute-only blocks
cannot be erased or programmed, and can only be read by the controller instruction fetch mechanism,
protecting the contents of those blocks from being read by either the controller or by a debugger.
1.3.2.3
ROM (see page 514)
The TM4C123BE6PM ROM is preprogrammed with the following software and programs:
■ TivaWare Peripheral Driver Library
■ TivaWare Boot Loader
■ Advanced Encryption Standard (AES) cryptography tables
■ Cyclic Redundancy Check (CRC) error-detection functionality
The TivaWare Peripheral Driver Library is a royalty-free software library for controlling on-chip
peripherals with a boot-loader capability. The library performs both peripheral initialization and
control functions, with a choice of polled or interrupt-driven peripheral support. In addition, the library
is designed to take full advantage of the stellar interrupt performance of the ARM Cortex-M4F core.
No special pragmas or custom assembly code prologue/epilogue functions are required. For
applications that require in-field programmability, the royalty-free TivaWare Boot Loader can act as
an application loader and support in-field firmware updates.
The Advanced Encryption Standard (AES) is a publicly defined encryption standard used by the
U.S. Government. AES is a strong encryption method with reasonable performance and size. In
addition, it is fast in both hardware and software, is fairly easy to implement, and requires little
memory. The Texas Instruments encryption package is available with full source code, and is based
on Lesser General Public License (LGPL) source. An LGPL means that the code can be used within
an application without any copyleft implications for the application (the code does not automatically
become open source). Modifications to the package source, however, must be open source.
CRC (Cyclic Redundancy Check) is a technique to validate a span of data has the same contents
as when previously checked. This technique can be used to validate correct receipt of messages
(nothing lost or modified in transit), to validate data after decompression, to validate that Flash
memory contents have not been changed, and for other cases where the data needs to be validated.
A CRC is preferred over a simple checksum (for example, XOR all bits) because it catches changes
more readily.
1.3.2.4
EEPROM (see page 522)
The TM4C123BE6PM microcontroller includes an EEPROM with the following features:
■ 2Kbytes of memory accessible as 512 32-bit words
■ 32 blocks of 16 words (64 bytes) each
■ Built-in wear leveling
■ Access protection per block
■ Lock protection option for the whole peripheral as well as per block using 32-bit to 96-bit unlock
codes (application selectable)
■ Interrupt support for write completion to avoid polling
48
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
■ Endurance of 500K writes (when writing at fixed offset in every alternate page in circular fashion)
to 15M operations (when cycling through two pages ) per each 2-page block.
1.3.3
Serial Communications Peripherals
The TM4C123BE6PM controller supports both asynchronous and synchronous serial communications
with:
■ Two CAN 2.0 A/B controllers
■ Eight UARTs with IrDA, 9-bit and ISO 7816 support.
■ Four I2C modules with four transmission speeds including high-speed mode
■ Four Synchronous Serial Interface modules (SSI)
The following sections provide more detail on each of these communications functions.
1.3.3.1
Controller Area Network (CAN) (see page 1035)
Controller Area Network (CAN) is a multicast shared serial-bus standard for connecting electronic
control units (ECUs). CAN was specifically designed to be robust in electromagnetically noisy
environments and can utilize a differential balanced line like RS-485 or twisted-pair wire. Originally
created for automotive purposes, it is now used in many embedded control applications (for example,
industrial or medical). Bit rates up to 1 Mbps are possible at network lengths below 40 meters.
Decreased bit rates allow longer network distances (for example, 125 Kbps at 500m).
A transmitter sends a message to all CAN nodes (broadcasting). Each node decides on the basis
of the identifier received whether it should process the message. The identifier also determines the
priority that the message enjoys in competition for bus access. Each CAN message can transmit
from 0 to 8 bytes of user information.
The TM4C123BE6PM microcontroller includes two CAN units with the following features:
■ CAN protocol version 2.0 part A/B
■ Bit rates up to 1 Mbps
■ 32 message objects with individual identifier masks
■ Maskable interrupt
■ Disable Automatic Retransmission mode for Time-Triggered CAN (TTCAN) applications
■ Programmable loopback mode for self-test operation
■ Programmable FIFO mode enables storage of multiple message objects
■ Gluelessly attaches to an external CAN transceiver through the CANnTX and CANnRX signals
1.3.3.2
UART (see page 880)
A Universal Asynchronous Receiver/Transmitter (UART) is an integrated circuit used for RS-232C
serial communications, containing a transmitter (parallel-to-serial converter) and a receiver
(serial-to-parallel converter), each clocked separately.
The TM4C123BE6PM microcontroller includes eight fully programmable 16C550-type UARTs.
Although the functionality is similar to a 16C550 UART, this UART design is not register compatible.
June 12, 2014
49
Texas Instruments-Production Data
Architectural Overview
The UART can generate individually masked interrupts from the Rx, Tx, modem flow control, and
error conditions. The module generates a single combined interrupt when any of the interrupts are
asserted and are unmasked.
The eight UARTs have the following features:
■ Programmable baud-rate generator allowing speeds up to 5 Mbps for regular speed (divide by
16) and 10 Mbps for high speed (divide by 8)
■ Separate 16x8 transmit (TX) and receive (RX) FIFOs to reduce CPU interrupt service loading
■ Programmable FIFO length, including 1-byte deep operation providing conventional
double-buffered interface
■ FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8
■ Standard asynchronous communication bits for start, stop, and parity
■ Line-break generation and detection
■ Fully programmable serial interface characteristics
– 5, 6, 7, or 8 data bits
– Even, odd, stick, or no-parity bit generation/detection
– 1 or 2 stop bit generation
■ IrDA serial-IR (SIR) encoder/decoder providing
– Programmable use of IrDA Serial Infrared (SIR) or UART input/output
– Support of IrDA SIR encoder/decoder functions for data rates up to 115.2 Kbps half-duplex
– Support of normal 3/16 and low-power (1.41-2.23 μs) bit durations
– Programmable internal clock generator enabling division of reference clock by 1 to 256 for
low-power mode bit duration
■ Support for communication with ISO 7816 smart cards
■ Modem flow control (on UART1)
■ EIA-485 9-bit support
■ Standard FIFO-level and End-of-Transmission interrupts
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Separate channels for transmit and receive
– Receive single request asserted when data is in the FIFO; burst request asserted at
programmed FIFO level
– Transmit single request asserted when there is space in the FIFO; burst request asserted at
programmed FIFO level
50
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
1.3.3.3
I2C (see page 984)
The Inter-Integrated Circuit (I2C) bus provides bi-directional data transfer through a two-wire design
(a serial data line SDA and a serial clock line SCL). The I2C bus interfaces to external I2C devices
such as serial memory (RAMs and ROMs), networking devices, LCDs, tone generators, and so on.
The I2C bus may also be used for system testing and diagnostic purposes in product development
and manufacture.
Each device on the I2C bus can be designated as either a master or a slave. I2C module supports
both sending and receiving data as either a master or a slave and can operate simultaneously as
both a master and a slave. Both the I2C master and slave can generate interrupts.
The TM4C123BE6PM microcontroller includes four I2C modules with the following features:
■ Devices on the I2C bus can be designated as either a master or a slave
– Supports both transmitting and receiving data as either a master or a slave
– Supports simultaneous master and slave operation
■ Four I2C modes
– Master transmit
– Master receive
– Slave transmit
– Slave receive
■ Four transmission speeds:
– Standard (100 Kbps)
– Fast-mode (400 Kbps)
– Fast-mode plus (1 Mbps)
– High-speed mode (3.33 Mbps)
■ Clock low timeout interrupt
■ Dual slave address capability
■ Glitch suppression
■ Master and slave interrupt generation
– Master generates interrupts when a transmit or receive operation completes (or aborts due
to an error)
– Slave generates interrupts when data has been transferred or requested by a master or when
a START or STOP condition is detected
■ Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing
mode
June 12, 2014
51
Texas Instruments-Production Data
Architectural Overview
1.3.3.4
SSI (see page 939)
Synchronous Serial Interface (SSI) is a four-wire bi-directional communications interface that converts
data between parallel and serial. The SSI module performs serial-to-parallel conversion on data
received from a peripheral device, and parallel-to-serial conversion on data transmitted to a peripheral
device. The SSI module can be configured as either a master or slave device. As a slave device,
the SSI module can also be configured to disable its output, which allows a master device to be
coupled with multiple slave devices. The TX and RX paths are buffered with separate internal FIFOs.
The SSI module also includes a programmable bit rate clock divider and prescaler to generate the
output serial clock derived from the SSI module's input clock. Bit rates are generated based on the
input clock and the maximum bit rate is determined by the connected peripheral.
The TM4C123BE6PM microcontroller includes four SSI modules with the following features:
■ Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments
synchronous serial interfaces
■ Master or slave operation
■ Programmable clock bit rate and prescaler
■ Separate transmit and receive FIFOs, each 16 bits wide and 8 locations deep
■ Programmable data frame size from 4 to 16 bits
■ Internal loopback test mode for diagnostic/debug testing
■ Standard FIFO-based interrupts and End-of-Transmission interrupt
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Separate channels for transmit and receive
– Receive single request asserted when data is in the FIFO; burst request asserted when FIFO
contains 4 entries
– Transmit single request asserted when there is space in the FIFO; burst request asserted
when four or more entries are available to be written in the FIFO
1.3.4
System Integration
The TM4C123BE6PM microcontroller provides a variety of standard system functions integrated
into the device, including:
■ Direct Memory Access Controller (DMA)
■ System control and clocks including on-chip precision 16-MHz oscillator
■ Six 32-bit timers (up to twelve 16-bit)
■ Six wide 64-bit timers (up to twelve 32-bit)
■ Twelve 32/64-bit Capture Compare PWM (CCP) pins
■ Lower-power battery-backed Hibernation module
52
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
■ Real-Time Clock in Hibernation module
■ Two Watchdog Timers
– One timer runs off the main oscillator
– One timer runs off the precision internal oscillator
■ Up to 43 GPIOs, depending on configuration
– Highly flexible pin muxing allows use as GPIO or one of several peripheral functions
– Independently configurable to 2-, 4- or 8-mA drive capability
– Up to 4 GPIOs can have 18-mA drive capability
The following sections provide more detail on each of these functions.
1.3.4.1
Direct Memory Access (see page 572)
The TM4C123BE6PM microcontroller includes a Direct Memory Access (DMA) controller, known
as micro-DMA (μDMA). The μDMA controller provides a way to offload data transfer tasks from the
Cortex-M4F processor, allowing for more efficient use of the processor and the available bus
bandwidth. The μDMA controller can perform transfers between memory and peripherals. It has
dedicated channels for each supported on-chip module and can be programmed to automatically
perform transfers between peripherals and memory as the peripheral is ready to transfer more data.
The μDMA controller provides the following features:
®
■ ARM PrimeCell 32-channel configurable µDMA controller
■ Support for memory-to-memory, memory-to-peripheral, and peripheral-to-memory in multiple
transfer modes
– Basic for simple transfer scenarios
– Ping-pong for continuous data flow
– Scatter-gather for a programmable list of up to 256 arbitrary transfers initiated from a single
request
■ Highly flexible and configurable channel operation
– Independently configured and operated channels
– Dedicated channels for supported on-chip modules
– Flexible channel assignments
– One channel each for receive and transmit path for bidirectional modules
– Dedicated channel for software-initiated transfers
– Per-channel configurable priority scheme
– Optional software-initiated requests for any channel
■ Two levels of priority
■ Design optimizations for improved bus access performance between µDMA controller and the
processor core
June 12, 2014
53
Texas Instruments-Production Data
Architectural Overview
– µDMA controller access is subordinate to core access
– RAM striping
– Peripheral bus segmentation
■ Data sizes of 8, 16, and 32 bits
■ Transfer size is programmable in binary steps from 1 to 1024
■ Source and destination address increment size of byte, half-word, word, or no increment
■ Maskable peripheral requests
■ Interrupt on transfer completion, with a separate interrupt per channel
1.3.4.2
System Control and Clocks (see page 207)
System control determines the overall operation of the device. It provides information about the
device, controls power-saving features, controls the clocking of the device and individual peripherals,
and handles reset detection and reporting.
■ Device identification information: version, part number, SRAM size, Flash memory size, and so
on
■ Power control
– On-chip fixed Low Drop-Out (LDO) voltage regulator
– Hibernation module handles the power-up/down 3.3 V sequencing and control for the core
digital logic and analog circuits
– Low-power options for microcontroller: Sleep and Deep-Sleep modes with clock gating
– Low-power options for on-chip modules: software controls shutdown of individual peripherals
and memory
– 3.3-V supply brown-out detection and reporting via interrupt or reset
■ Multiple clock sources for microcontroller system clock. The following clock sources are provided
to the TM4C123BE6PM microcontroller:
– Precision Internal Oscillator (PIOSC) providing a 16-MHz frequency
• 16 MHz ±3% across temperature and voltage
• Can be recalibrated with 7-bit trim resolution to achieve better accuracy (16 MHz ±1%)
• Software power down control for low power modes
– Main Oscillator (MOSC): A frequency-accurate clock source by one of two means: an external
single-ended clock source is connected to the OSC0 input pin, or an external crystal is
connected across the OSC0 input and OSC1 output pins.
– Low Frequency Internal Oscillator (LFIOSC): On-chip resource used during power-saving
modes
54
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
– Hibernate RTC oscillator (RTCOSC) clock that can be configured to be the 32.768-kHz
external oscillator source from the Hibernation (HIB) module or the HIB Low Frequency clock
source (HIB LFIOSC), which is located within the Hibernation Module.
■ Flexible reset sources
– Power-on reset (POR)
– Reset pin assertion
– Brown-out reset (BOR) detector alerts to system power drops
– Software reset
– Watchdog timer reset
– MOSC failure
1.3.4.3
Programmable Timers (see page 691)
Programmable timers can be used to count or time external events that drive the Timer input pins.
Each 16/32-bit GPTM block provides two 16-bit timers/counters that can be configured to operate
independently as timers or event counters, or configured to operate as one 32-bit timer or one 32-bit
Real-Time Clock (RTC). Each 32/64-bit Wide GPTM block provides two 32-bit timers/counters that
can be configured to operate independently as timersor event counters, or configured to operate
as one 64-bit timer or one 64-bit Real-Time Clock (RTC). Timers can also be used to trigger
analog-to-digital (ADC) conversions and DMA transfers.
The General-Purpose Timer Module (GPTM) contains six 16/32-bit GPTM blocks and six 32/64-bit
Wide GPTM blocks with the following functional options:
■ 16/32-bit operating modes:
– 16- or 32-bit programmable one-shot timer
– 16- or 32-bit programmable periodic timer
– 16-bit general-purpose timer with an 8-bit prescaler
– 32-bit Real-Time Clock (RTC) when using an external 32.768-KHz clock as the input
– 16-bit input-edge count- or time-capture modes with an 8-bit prescaler
– 16-bit PWM mode with an 8-bit prescaler and software-programmable output inversion of the
PWM signal
■ 32/64-bit operating modes:
– 32- or 64-bit programmable one-shot timer
– 32- or 64-bit programmable periodic timer
– 32-bit general-purpose timer with a 16-bit prescaler
– 64-bit Real-Time Clock (RTC) when using an external 32.768-KHz clock as the input
– 32-bit input-edge count- or time-capture modes with a16-bit prescaler
June 12, 2014
55
Texas Instruments-Production Data
Architectural Overview
– 32-bit PWM mode with a 16-bit prescaler and software-programmable output inversion of the
PWM signal
■ Count up or down
■ Twelve 16/32-bit Capture Compare PWM pins (CCP)
■ Twelve 32/64-bit Capture Compare PWM pins (CCP)
■ Daisy chaining of timer modules to allow a single timer to initiate multiple timing events
■ Timer synchronization allows selected timers to start counting on the same clock cycle
■ ADC event trigger
■ User-enabled stalling when the microcontroller asserts CPU Halt flag during debug (excluding
RTC mode)
■ Ability to determine the elapsed time between the assertion of the timer interrupt and entry into
the interrupt service routine
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Dedicated channel for each timer
– Burst request generated on timer interrupt
1.3.4.4
CCP Pins (see page 699)
Capture Compare PWM pins (CCP) can be used by the General-Purpose Timer Module to time/count
external events using the CCP pin as an input. Alternatively, the GPTM can generate a simple PWM
output on the CCP pin.
The TM4C123BE6PM microcontroller includes twelve 16/32-bit CCP pins that can be programmed
to operate in the following modes:
■ Capture: The GP Timer is incremented/decremented by programmed events on the CCP input.
The GP Timer captures and stores the current timer value when a programmed event occurs.
■ Compare: The GP Timer is incremented/decremented by programmed events on the CCP input.
The GP Timer compares the current value with a stored value and generates an interrupt when
a match occurs.
■ PWM: The GP Timer is incremented/decremented by the system clock. A PWM signal is generated
based on a match between the counter value and a value stored in a match register and is output
on the CCP pin.
1.3.4.5
Hibernation Module (HIB) (see page 481)
The Hibernation module provides logic to switch power off to the main processor and peripherals
and to wake on external or time-based events. The Hibernation module includes power-sequencing
logic and has the following features:
■ 32-bit real-time seconds counter (RTC) with 1/32,768 second resolution and a 15-bit sub-seconds
counter
56
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
– 32-bit RTC seconds match register and a 15-bit sub seconds match for timed wake-up and
interrupt generation with 1/32,768 second resolution
– RTC predivider trim for making fine adjustments to the clock rate
■ Two mechanisms for power control
– System power control using discrete external regulator
– On-chip power control using internal switches under register control
■ Dedicated pin for waking using an external signal
■ RTC operational and hibernation memory valid as long as VDD or VBAT is valid
■ Low-battery detection, signaling, and interrupt generation, with optional wake on low battery
■ GPIO pin state can be retained during hibernation
■ Clock source from a 32.768-kHz external crystal or oscillator
■ Sixteen 32-bit words of battery-backed memory to save state during hibernation
■ Programmable interrupts for:
– RTC match
– External wake
– Low battery
1.3.4.6
Watchdog Timers (see page 761)
A watchdog timer is used to regain control when a system has failed due to a software error or to
the failure of an external device to respond in the expected way. The TM4C123BE6PM Watchdog
Timer can generate an interrupt, a non-maskable interrupt, or a reset when a time-out value is
reached. In addition, the Watchdog Timer is ARM FiRM-compliant and can be configured to generate
an interrupt to the microcontroller on its first time-out, and to generate a reset signal on its second
timeout. Once the Watchdog Timer has been configured, the lock register can be written to prevent
the timer configuration from being inadvertently altered.
The TM4C123BE6PM microcontroller has two Watchdog Timer modules: Watchdog Timer 0 uses
the system clock for its timer clock; Watchdog Timer 1 uses the PIOSC as its timer clock. The
Watchdog Timer module has the following features:
■ 32-bit down counter with a programmable load register
■ Separate watchdog clock with an enable
■ Programmable interrupt generation logic with interrupt masking and optional NMI function
■ Lock register protection from runaway software
■ Reset generation logic with an enable/disable
■ User-enabled stalling when the microcontroller asserts the CPU Halt flag during debug
June 12, 2014
57
Texas Instruments-Production Data
Architectural Overview
1.3.4.7
Programmable GPIOs (see page 636)
General-purpose input/output (GPIO) pins offer flexibility for a variety of connections. The
TM4C123BE6PM GPIO module is comprised of six physical GPIO blocks, each corresponding to
an individual GPIO port. The GPIO module is FiRM-compliant (compliant to the ARM Foundation
IP for Real-Time Microcontrollers specification) and supports 0-43 programmable input/output pins.
The number of GPIOs available depends on the peripherals being used (see “Signal
Tables” on page 1200 for the signals available to each GPIO pin).
■ Up to 43 GPIOs, depending on configuration
■ Highly flexible pin muxing allows use as GPIO or one of several peripheral functions
■ 5-V-tolerant in input configuration
■ Ports A-G accessed through the Advanced Peripheral Bus (APB)
■ Fast toggle capable of a change every clock cycle for ports on AHB, every two clock cycles for
ports on APB
■ Programmable control for GPIO interrupts
– Interrupt generation masking
– Edge-triggered on rising, falling, or both
– Level-sensitive on High or Low values
■ Bit masking in both read and write operations through address lines
■ Can be used to initiate an ADC sample sequence or a μDMA transfer
■ Pin state can be retained during Hibernation mode
■ Pins configured as digital inputs are Schmitt-triggered
■ Programmable control for GPIO pad configuration
– Weak pull-up or pull-down resistors
– 2-mA, 4-mA, and 8-mA pad drive for digital communication; up to four pads can sink 18-mA
for high-current applications
– Slew rate control for 8-mA pad drive
– Open drain enables
– Digital input enables
1.3.5
Advanced Motion Control
The TM4C123BE6PM microcontroller provides motion control functions integrated into the device,
including:
■ Two PWM modules, with a total of 16 advanced PWM outputs for motion and energy applications
■ Two fault inputs to promote low-latency shutdown
58
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
■ Two Quadrature Encoder Inputs (QEI)
The following provides more detail on these motion control functions.
1.3.5.1
PWM (see page 1101)
The TM4C123BE6PM microcontroller contains two PWM modules, each with four PWM generator
blocks and a control block, for a total of 16 PWM outputs. Pulse width modulation (PWM) is a
powerful technique for digitally encoding analog signal levels. High-resolution counters are used to
generate a square wave, and the duty cycle of the square wave is modulated to encode an analog
signal. Typical applications include switching power supplies and motor control. Each
TM4C123BE6PM PWM module consists of four PWM generator block and a control block. Each
PWM generator block contains one timer (16-bit down or up/down counter), two comparators, a
PWM signal generator, a dead-band generator, and an interrupt/ADC-trigger selector. Each PWM
generator block produces two PWM signals that can either be independent signals or a single pair
of complementary signals with dead-band delays inserted.
Each PWM generator has the following features:
■ One fault-condition handling inputs to quickly provide low-latency shutdown and prevent damage
to the motor being controlled, for a total of two inputs
■ One 16-bit counter
– Runs in Down or Up/Down mode
– Output frequency controlled by a 16-bit load value
– Load value updates can be synchronized
– Produces output signals at zero and load value
■ Two PWM comparators
– Comparator value updates can be synchronized
– Produces output signals on match
■ PWM signal generator
– Output PWM signal is constructed based on actions taken as a result of the counter and
PWM comparator output signals
– Produces two independent PWM signals
■ Dead-band generator
– Produces two PWM signals with programmable dead-band delays suitable for driving a half-H
bridge
– Can be bypassed, leaving input PWM signals unmodified
■ Can initiate an ADC sample sequence
June 12, 2014
59
Texas Instruments-Production Data
Architectural Overview
The control block determines the polarity of the PWM signals and which signals are passed through
to the pins. The output of the PWM generation blocks are managed by the output control block
before being passed to the device pins. The PWM control block has the following options:
■ PWM output enable of each PWM signal
■ Optional output inversion of each PWM signal (polarity control)
■ Optional fault handling for each PWM signal
■ Synchronization of timers in the PWM generator blocks
■ Synchronization of timer/comparator updates across the PWM generator blocks
■ Extended PWM synchronization of timer/comparator updates across the PWM generator blocks
■ Interrupt status summary of the PWM generator blocks
■ Extended PWM fault handling, with multiple fault signals, programmable polarities, and filtering
■ PWM generators can be operated independently or synchronized with other generators
1.3.5.2
QEI (see page 1176)
A quadrature encoder, also known as a 2-channel incremental encoder, converts linear displacement
into a pulse signal. By monitoring both the number of pulses and the relative phase of the two signals,
the position, direction of rotation, and speed can be tracked. In addition, a third channel, or index
signal, can be used to reset the position counter. The TM4C123BE6PM quadrature encoder with
index (QEI) module interprets the code produced by a quadrature encoder wheel to integrate position
over time and determine direction of rotation. In addition, it can capture a running estimate of the
velocity of the encoder wheel. The input frequency of the QEI inputs may be as high as 1/4 of the
processor frequency (for example, 20 MHz for a 80-MHz system).
The TM4C123BE6PM microcontroller includes two QEI modules providing control of two motors at
the same time with the following features:
■ Position integrator that tracks the encoder position
■ Programmable noise filter on the inputs
■ Velocity capture using built-in timer
■ The input frequency of the QEI inputs may be as high as 1/4 of the processor frequency (for
example, 12.5 MHz for a 50-MHz system)
■ Interrupt generation on:
– Index pulse
– Velocity-timer expiration
– Direction change
– Quadrature error detection
60
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
1.3.6
Analog
The TM4C123BE6PM microcontroller provides analog functions integrated into the device, including:
■ Two 12-bit Analog-to-Digital Converters (ADC), with a total of 12 analog input channels and each
with a sample rate of one million samples/second
■ Two analog comparators
■ On-chip voltage regulator
The following provides more detail on these analog functions.
1.3.6.1
ADC (see page 786)
An analog-to-digital converter (ADC) is a peripheral that converts a continuous analog voltage to a
discrete digital number. The TM4C123BE6PM ADC module features 12-bit conversion resolution
and supports 12 input channels plus an internal temperature sensor. Four buffered sample
sequencers allow rapid sampling of up to 12 analog input sources without controller intervention.
Each sample sequencer provides flexible programming with fully configurable input source, trigger
events, interrupt generation, and sequencer priority. Each ADC module has a digital comparator
function that allows the conversion value to be diverted to a comparison unit that provides eight
digital comparators.
The TM4C123BE6PM microcontroller provides two ADC modules, each with the following features:
■ 12 shared analog input channels
■ 12-bit precision ADC
■ Single-ended and differential-input configurations
■ On-chip internal temperature sensor
■ Maximum sample rate of one million samples/second
■ Optional phase shift in sample time programmable from 22.5º to 337.5º
■ Four programmable sample conversion sequencers from one to eight entries long, with
corresponding conversion result FIFOs
■ Flexible trigger control
– Controller (software)
– Timers
– Analog Comparators
– PWM
– GPIO
■ Hardware averaging of up to 64 samples
■ Eight digital comparators
June 12, 2014
61
Texas Instruments-Production Data
Architectural Overview
■ Power and ground for the analog circuitry is separate from the digital power and ground
■ Efficient transfers using Micro Direct Memory Access Controller (µDMA)
– Dedicated channel for each sample sequencer
– ADC module uses burst requests for DMA
1.3.6.2
Analog Comparators (see page 1086)
An analog comparator is a peripheral that compares two analog voltages and provides a logical
output that signals the comparison result. The TM4C123BE6PM microcontroller provides two
independent integrated analog comparators that can be configured to drive an output or generate
an interrupt or ADC event.
The comparator can provide its output to a device pin, acting as a replacement for an analog
comparator on the board, or it can be used to signal the application via interrupts or triggers to the
ADC to cause it to start capturing a sample sequence. The interrupt generation and ADC triggering
logic is separate. This means, for example, that an interrupt can be generated on a rising edge and
the ADC triggered on a falling edge.
The TM4C123BE6PM microcontroller provides two independent integrated analog comparators
with the following functions:
■ Compare external pin input to external pin input or to internal programmable voltage reference
■ Compare a test voltage against any one of the following voltages:
– An individual external reference voltage
– A shared single external reference voltage
– A shared internal reference voltage
1.3.7
JTAG and ARM Serial Wire Debug (see page 195)
The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and
Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface
for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR)
can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing
information on the components. The JTAG Port also provides a means of accessing and controlling
design-for-test features such as I/O pin observation and control, scan testing, and debugging. Texas
Instruments replaces the ARM SW-DP and JTAG-DP with the ARM Serial Wire JTAG Debug Port
(SWJ-DP) interface. The SWJ-DP interface combines the SWD and JTAG debug ports into one
module providing all the normal JTAG debug and test functionality plus real-time access to system
memory without halting the core or requiring any target resident code. The SWJ-DP interface has
the following features:
■ IEEE 1149.1-1990 compatible Test Access Port (TAP) controller
■ Four-bit Instruction Register (IR) chain for storing JTAG instructions
■ IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, and EXTEST
■ ARM additional instructions: APACC, DPACC and ABORT
■ Integrated ARM Serial Wire Debug (SWD)
62
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
– Serial Wire JTAG Debug Port (SWJ-DP)
– Flash Patch and Breakpoint (FPB) unit for implementing breakpoints
– Data Watchpoint and Trace (DWT) unit for implementing watchpoints, trigger resources, and
system profiling
– Instrumentation Trace Macrocell (ITM) for support of printf style debugging
– Embedded Trace Macrocell (ETM) for instruction trace capture
– Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer
1.3.8
Packaging and Temperature
■ 64-pin RoHS-compliant LQFP package
■ Industrial (-40°C to 85°C) ambient temperature range
1.4
TM4C123BE6PM Microcontroller Hardware Details
Details on the pins and package can be found in the following sections:
■ “Pin Diagram” on page 1199
■ “Signal Tables” on page 1200
■ “Electrical Characteristics” on page 1226
■ “Package Information” on page 1269
1.5
Kits
The Tiva™ C Series provides the hardware and software tools that engineers need to begin
development quickly.
■ Reference Design Kits accelerate product development by providing ready-to-run hardware and
comprehensive documentation including hardware design files
■ Evaluation Kits provide a low-cost and effective means of evaluating TM4C123BE6PM
microcontrollers before purchase
■ Development Kits provide you with all the tools you need to develop and prototype embedded
applications right out of the box
See the Tiva series website at http://www.ti.com/tiva-c for the latest tools available, or ask your
distributor.
1.6
Support Information
For support on Tiva™ C Series products, contact the TI Worldwide Product Information Center
nearest you.
June 12, 2014
63
Texas Instruments-Production Data
The Cortex-M4F Processor
2
The Cortex-M4F Processor
The ARM® Cortex™-M4F processor provides a high-performance, low-cost platform that meets the
system requirements of minimal memory implementation, reduced pin count, and low power
consumption, while delivering outstanding computational performance and exceptional system
response to interrupts. Features include:
®
■ 32-bit ARM Cortex™-M4F architecture optimized for small-footprint embedded applications
■ 80-MHz operation; 100 DMIPS performance
■ Outstanding processing performance combined with fast interrupt handling
■ Thumb-2 mixed 16-/32-bit instruction set delivers the high performance expected of a 32-bit
ARM core in a compact memory size usually associated with 8- and 16-bit devices, typically in
the range of a few kilobytes of memory for microcontroller-class applications
– Single-cycle multiply instruction and hardware divide
– Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined
peripheral control
– Unaligned data access, enabling data to be efficiently packed into memory
■ IEEE754-compliant single-precision Floating-Point Unit (FPU)
■ 16-bit SIMD vector processing unit
■ Fast code execution permits slower processor clock or increases sleep mode time
■ Harvard architecture characterized by separate buses for instruction and data
■ Efficient processor core, system and memories
■ Hardware division and fast digital-signal-processing orientated multiply accumulate
■ Saturating arithmetic for signal processing
■ Deterministic, high-performance interrupt handling for time-critical applications
■ Memory protection unit (MPU) to provide a privileged mode for protected operating system
functionality
■ Enhanced system debug with extensive breakpoint and trace capabilities
■ Serial Wire Debug and Serial Wire Trace reduce the number of pins required for debugging and
tracing
■ Migration from the ARM7™ processor family for better performance and power efficiency
■ Optimized for single-cycle Flash memory usage up to specific frequencies; see “Internal
Memory” on page 512 for more information.
■ Ultra-low power consumption with integrated sleep modes
64
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
The Tiva™ C Series microcontrollers builds on this core to bring high-performance 32-bit computing
to
This chapter provides information on the Tiva™ C Series implementation of the Cortex-M4F
processor, including the programming model, the memory model, the exception model, fault handling,
and power management.
For technical details on the instruction set, see the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI 0553A).
2.1
Block Diagram
The Cortex-M4F processor is built on a high-performance processor core, with a 3-stage pipeline
Harvard architecture, making it ideal for demanding embedded applications. The processor delivers
exceptional power efficiency through an efficient instruction set and extensively optimized design,
providing high-end processing hardware including IEEE754-compliant single-precision floating-point
computation, a range of single-cycle and SIMD multiplication and multiply-with-accumulate
capabilities, saturating arithmetic and dedicated hardware division.
To facilitate the design of cost-sensitive devices, the Cortex-M4F processor implements tightly
coupled system components that reduce processor area while significantly improving interrupt
handling and system debug capabilities. The Cortex-M4F processor implements a version of the
Thumb® instruction set based on Thumb-2 technology, ensuring high code density and reduced
program memory requirements. The Cortex-M4F instruction set provides the exceptional performance
expected of a modern 32-bit architecture, with the high code density of 8-bit and 16-bit
microcontrollers.
The Cortex-M4F processor closely integrates a nested interrupt controller (NVIC), to deliver
industry-leading interrupt performance. The TM4C123BE6PM NVIC includes a non-maskable
interrupt (NMI) and provides eight interrupt priority levels. The tight integration of the processor core
and NVIC provides fast execution of interrupt service routines (ISRs), dramatically reducing interrupt
latency. The hardware stacking of registers and the ability to suspend load-multiple and store-multiple
operations further reduce interrupt latency. Interrupt handlers do not require any assembler stubs
which removes code overhead from the ISRs. Tail-chaining optimization also significantly reduces
the overhead when switching from one ISR to another. To optimize low-power designs, the NVIC
integrates with the sleep modes, including Deep-sleep mode, which enables the entire device to be
rapidly powered down.
June 12, 2014
65
Texas Instruments-Production Data
The Cortex-M4F Processor
Figure 2-1. CPU Block Diagram
Nested
Vectored
Interrupt
Controller
FPU
Interrupts
Sleep
ARM
Cortex-M4F
CM4 Core
Debug
Instructions
Data
Embedded
Trace
Macrocell
Memory
Protection
Unit
Flash
Patch and
Breakpoint
Instrumentation
Data
Watchpoint Trace Macrocell
and Trace
ROM
Table
Private Peripheral
Bus
(internal)
Adv. Peripheral
Bus
Bus
Matrix
Serial Wire JTAG
Debug Port
Debug
Access Port
2.2
Overview
2.2.1
System-Level Interface
Trace
Port
Interface
Unit
Serial
Wire
Output
Trace
Port
(SWO)
I-code bus
D-code bus
System bus
The Cortex-M4F processor provides multiple interfaces using AMBA® technology to provide
high-speed, low-latency memory accesses. The core supports unaligned data accesses and
implements atomic bit manipulation that enables faster peripheral controls, system spinlocks, and
thread-safe Boolean data handling.
The Cortex-M4F processor has a memory protection unit (MPU) that provides fine-grain memory
control, enabling applications to implement security privilege levels and separate code, data and
stack on a task-by-task basis.
2.2.2
Integrated Configurable Debug
The Cortex-M4F processor implements a complete hardware debug solution, providing high system
visibility of the processor and memory through either a traditional JTAG port or a 2-pin Serial Wire
Debug (SWD) port that is ideal for microcontrollers and other small package devices. The Tiva™
C Series implementation replaces the ARM SW-DP and JTAG-DP with the ARM
CoreSight™-compliant Serial Wire JTAG Debug Port (SWJ-DP) interface. The SWJ-DP interface
combines the SWD and JTAG debug ports into one module. See the ARM® Debug Interface V5
Architecture Specification for details on SWJ-DP.
For system trace, the processor integrates an Instrumentation Trace Macrocell (ITM) alongside data
watchpoints and a profiling unit. To enable simple and cost-effective profiling of the system trace
events, a Serial Wire Viewer (SWV) can export a stream of software-generated messages, data
trace, and profiling information through a single pin.
66
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
The Embedded Trace Macrocell (ETM) delivers unrivaled instruction trace capture in an area smaller
than traditional trace units, enabling full instruction trace. For more details on the ARM ETM, see
the ARM® Embedded Trace Macrocell Architecture Specification.
The Flash Patch and Breakpoint Unit (FPB) provides up to eight hardware breakpoint comparators
that debuggers can use. The comparators in the FPB also provide remap functions for up to eight
words of program code in the code memory region. This FPB enables applications stored in a
read-only area of Flash memory to be patched in another area of on-chip SRAM or Flash memory.
If a patch is required, the application programs the FPB to remap a number of addresses. When
those addresses are accessed, the accesses are redirected to a remap table specified in the FPB
configuration.
For more information on the Cortex-M4F debug capabilities, see theARM® Debug Interface V5
Architecture Specification.
2.2.3
Trace Port Interface Unit (TPIU)
The TPIU acts as a bridge between the Cortex-M4F trace data from the ITM, and an off-chip Trace
Port Analyzer, as shown in Figure 2-2 on page 67.
Figure 2-2. TPIU Block Diagram
2.2.4
Debug
ATB
Slave
Port
ARM® Trace
Bus (ATB)
Interface
APB
Slave
Port
Advance
Peripheral
Bus (APB)
Interface
Asynchronous FIFO
Trace Out
(serializer)
Serial Wire
Trace Port
(SWO)
Cortex-M4F System Component Details
The Cortex-M4F includes the following system components:
■ SysTick
A 24-bit count-down timer that can be used as a Real-Time Operating System (RTOS) tick timer
or as a simple counter (see “System Timer (SysTick)” on page 118).
■ Nested Vectored Interrupt Controller (NVIC)
June 12, 2014
67
Texas Instruments-Production Data
The Cortex-M4F Processor
An embedded interrupt controller that supports low latency interrupt processing (see “Nested
Vectored Interrupt Controller (NVIC)” on page 119).
■ System Control Block (SCB)
The programming model interface to the processor. The SCB provides system implementation
information and system control, including configuration, control, and reporting of system exceptions
(see “System Control Block (SCB)” on page 120).
■ Memory Protection Unit (MPU)
Improves system reliability by defining the memory attributes for different memory regions. The
MPU provides up to eight different regions and an optional predefined background region (see
“Memory Protection Unit (MPU)” on page 120).
■ Floating-Point Unit (FPU)
Fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and
square-root operations. It also provides conversions between fixed-point and floating-point data
formats, and floating-point constant instructions (see “Floating-Point Unit (FPU)” on page 125).
2.3
Programming Model
This section describes the Cortex-M4F programming model. In addition to the individual core register
descriptions, information about the processor modes and privilege levels for software execution and
stacks is included.
2.3.1
Processor Mode and Privilege Levels for Software Execution
The Cortex-M4F has two modes of operation:
■ Thread mode
Used to execute application software. The processor enters Thread mode when it comes out of
reset.
■ Handler mode
Used to handle exceptions. When the processor has finished exception processing, it returns to
Thread mode.
In addition, the Cortex-M4F has two privilege levels:
■ Unprivileged
In this mode, software has the following restrictions:
– Limited access to the MSR and MRS instructions and no use of the CPS instruction
– No access to the system timer, NVIC, or system control block
– Possibly restricted access to memory or peripherals
■ Privileged
In this mode, software can use all the instructions and has access to all resources.
In Thread mode, the CONTROL register (see page 83) controls whether software execution is
privileged or unprivileged. In Handler mode, software execution is always privileged.
68
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Only privileged software can write to the CONTROL register to change the privilege level for software
execution in Thread mode. Unprivileged software can use the SVC instruction to make a supervisor
call to transfer control to privileged software.
2.3.2
Stacks
The processor uses a full descending stack, meaning that the stack pointer indicates the last stacked
item on the memory. When the processor pushes a new item onto the stack, it decrements the stack
pointer and then writes the item to the new memory location. The processor implements two stacks:
the main stack and the process stack, with a pointer for each held in independent registers (see the
SP register on page 73).
In Thread mode, the CONTROL register (see page 83) controls whether the processor uses the
main stack or the process stack. In Handler mode, the processor always uses the main stack. The
options for processor operations are shown in Table 2-1 on page 69.
Table 2-1. Summary of Processor Mode, Privilege Level, and Stack Use
Processor Mode
Use
Privilege Level
Thread
Applications
Privileged or unprivileged
Handler
Exception handlers
Always privileged
Stack Used
a
Main stack or process stack
a
Main stack
a. See CONTROL (page 83).
2.3.3
Register Map
Figure 2-3 on page 70 shows the Cortex-M4F register set. Table 2-2 on page 70 lists the Core
registers. The core registers are not memory mapped and are accessed by register name, so the
base address is n/a (not applicable) and there is no offset.
June 12, 2014
69
Texas Instruments-Production Data
The Cortex-M4F Processor
Figure 2-3. Cortex-M4F Register Set
R0
R1
R2
R3
Low registers
R4
R5
General-purpose registers
R6
R7
R8
R9
High registers
R10
R11
R12
Stack Pointer
SP (R13)
Link Register
LR (R14)
Program Counter
PC (R15)
PSP‡
PSR
MSP‡
‡
Banked version of SP
Program status register
PRIMASK
FAULTMASK
Exception mask registers
Special registers
BASEPRI
CONTROL
CONTROL register
Table 2-2. Processor Register Map
Offset
Name
Type
Reset
Description
See
page
-
R0
RW
-
Cortex General-Purpose Register 0
72
-
R1
RW
-
Cortex General-Purpose Register 1
72
-
R2
RW
-
Cortex General-Purpose Register 2
72
-
R3
RW
-
Cortex General-Purpose Register 3
72
-
R4
RW
-
Cortex General-Purpose Register 4
72
-
R5
RW
-
Cortex General-Purpose Register 5
72
-
R6
RW
-
Cortex General-Purpose Register 6
72
-
R7
RW
-
Cortex General-Purpose Register 7
72
-
R8
RW
-
Cortex General-Purpose Register 8
72
-
R9
RW
-
Cortex General-Purpose Register 9
72
-
R10
RW
-
Cortex General-Purpose Register 10
72
-
R11
RW
-
Cortex General-Purpose Register 11
72
70
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-2. Processor Register Map (continued)
Offset
Name
Type
Reset
Description
See
page
-
R12
RW
-
Cortex General-Purpose Register 12
72
-
SP
RW
-
Stack Pointer
73
-
LR
RW
0xFFFF.FFFF
Link Register
74
-
PC
RW
-
Program Counter
75
-
PSR
RW
0x0100.0000
Program Status Register
76
-
PRIMASK
RW
0x0000.0000
Priority Mask Register
80
-
FAULTMASK
RW
0x0000.0000
Fault Mask Register
81
-
BASEPRI
RW
0x0000.0000
Base Priority Mask Register
82
-
CONTROL
RW
0x0000.0000
Control Register
83
-
FPSC
RW
-
Floating-Point Status Control
85
2.3.4
Register Descriptions
This section lists and describes the Cortex-M4F registers, in the order shown in Figure
2-3 on page 70. The core registers are not memory mapped and are accessed by register name
rather than offset.
Note:
The register type shown in the register descriptions refers to type during program execution
in Thread mode and Handler mode. Debug access can differ.
June 12, 2014
71
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 1: Cortex General-Purpose Register 0 (R0)
Register 2: Cortex General-Purpose Register 1 (R1)
Register 3: Cortex General-Purpose Register 2 (R2)
Register 4: Cortex General-Purpose Register 3 (R3)
Register 5: Cortex General-Purpose Register 4 (R4)
Register 6: Cortex General-Purpose Register 5 (R5)
Register 7: Cortex General-Purpose Register 6 (R6)
Register 8: Cortex General-Purpose Register 7 (R7)
Register 9: Cortex General-Purpose Register 8 (R8)
Register 10: Cortex General-Purpose Register 9 (R9)
Register 11: Cortex General-Purpose Register 10 (R10)
Register 12: Cortex General-Purpose Register 11 (R11)
Register 13: Cortex General-Purpose Register 12 (R12)
The Rn registers are 32-bit general-purpose registers for data operations and can be accessed
from either privileged or unprivileged mode.
Cortex General-Purpose Register 0 (R0)
Type RW, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
DATA
Type
Reset
DATA
Type
Reset
Bit/Field
Name
Type
Reset
31:0
DATA
RW
-
Description
Register data.
72
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 14: Stack Pointer (SP)
The Stack Pointer (SP) is register R13. In Thread mode, the function of this register changes
depending on the ASP bit in the Control Register (CONTROL) register. When the ASP bit is clear,
this register is the Main Stack Pointer (MSP). When the ASP bit is set, this register is the Process
Stack Pointer (PSP). On reset, the ASP bit is clear, and the processor loads the MSP with the value
from address 0x0000.0000. The MSP can only be accessed in privileged mode; the PSP can be
accessed in either privileged or unprivileged mode.
Stack Pointer (SP)
Type RW, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
SP
Type
Reset
SP
Type
Reset
Bit/Field
Name
Type
Reset
31:0
SP
RW
-
Description
This field is the address of the stack pointer.
June 12, 2014
73
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 15: Link Register (LR)
The Link Register (LR) is register R14, and it stores the return information for subroutines, function
calls, and exceptions. The Link Register can be accessed from either privileged or unprivileged
mode.
EXC_RETURN is loaded into the LR on exception entry. See Table 2-10 on page 106 for the values
and description.
Link Register (LR)
Type RW, reset 0xFFFF.FFFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
7
6
5
4
3
2
1
0
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
LINK
Type
Reset
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
15
14
13
12
11
10
9
8
LINK
Type
Reset
RW
1
RW
1
RW
1
RW
1
RW
1
RW
1
Bit/Field
Name
Type
31:0
LINK
RW
RW
1
Reset
RW
1
Description
0xFFFF.FFFF This field is the return address.
74
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 16: Program Counter (PC)
The Program Counter (PC) is register R15, and it contains the current program address. On reset,
the processor loads the PC with the value of the reset vector, which is at address 0x0000.0004. Bit
0 of the reset vector is loaded into the THUMB bit of the EPSR at reset and must be 1. The PC register
can be accessed in either privileged or unprivileged mode.
Program Counter (PC)
Type RW, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
PC
Type
Reset
PC
Type
Reset
Bit/Field
Name
Type
Reset
31:0
PC
RW
-
Description
This field is the current program address.
June 12, 2014
75
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 17: Program Status Register (PSR)
Note:
This register is also referred to as xPSR.
The Program Status Register (PSR) has three functions, and the register bits are assigned to the
different functions:
■ Application Program Status Register (APSR), bits 31:27, bits 19:16
■ Execution Program Status Register (EPSR), bits 26:24, 15:10
■ Interrupt Program Status Register (IPSR), bits 7:0
The PSR, IPSR, and EPSR registers can only be accessed in privileged mode; the APSR register
can be accessed in either privileged or unprivileged mode.
APSR contains the current state of the condition flags from previous instruction executions.
EPSR contains the Thumb state bit and the execution state bits for the If-Then (IT) instruction or
the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple
instruction. Attempts to read the EPSR directly through application software using the MSR instruction
always return zero. Attempts to write the EPSR using the MSR instruction in application software
are always ignored. Fault handlers can examine the EPSR value in the stacked PSR to determine
the operation that faulted (see “Exception Entry and Return” on page 103).
IPSR contains the exception type number of the current Interrupt Service Routine (ISR).
These registers can be accessed individually or as a combination of any two or all three registers,
using the register name as an argument to the MSR or MRS instructions. For example, all of the
registers can be read using PSR with the MRS instruction, or APSR only can be written to using
APSR with the MSR instruction. page 76 shows the possible register combinations for the PSR. See
the MRS and MSR instruction descriptions in the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI 0553A) for more information
about how to access the program status registers.
Table 2-3. PSR Register Combinations
Register
Type
PSR
RW
Combination
APSR, EPSR, and IPSR
IEPSR
RO
EPSR and IPSR
a, b
a
APSR and IPSR
b
APSR and EPSR
IAPSR
RW
EAPSR
RW
a. The processor ignores writes to the IPSR bits.
b. Reads of the EPSR bits return zero, and the processor ignores writes to these bits.
Program Status Register (PSR)
Type RW, reset 0x0100.0000
Type
Reset
31
30
29
28
27
N
Z
C
V
Q
26
RW
0
RW
0
RW
0
RW
0
RW
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
ICI / IT
Type
Reset
RO
0
RO
0
RO
0
25
ICI / IT
24
23
22
THUMB
21
RO
0
RO
0
RO
0
RO
0
19
18
17
16
RW
0
RW
0
RW
0
3
2
1
0
RO
0
RO
0
RO
0
RO
0
GE
reserved
RO
0
20
reserved
ISRNUM
RO
0
RO
0
76
RO
0
RO
0
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
31
N
RW
0
Description
APSR Negative or Less Flag
Value Description
1
The previous operation result was negative or less than.
0
The previous operation result was positive, zero, greater than,
or equal.
The value of this bit is only meaningful when accessing PSR or APSR.
30
Z
RW
0
APSR Zero Flag
Value Description
1
The previous operation result was zero.
0
The previous operation result was non-zero.
The value of this bit is only meaningful when accessing PSR or APSR.
29
C
RW
0
APSR Carry or Borrow Flag
Value Description
1
The previous add operation resulted in a carry bit or the previous
subtract operation did not result in a borrow bit.
0
The previous add operation did not result in a carry bit or the
previous subtract operation resulted in a borrow bit.
The value of this bit is only meaningful when accessing PSR or APSR.
28
V
RW
0
APSR Overflow Flag
Value Description
1
The previous operation resulted in an overflow.
0
The previous operation did not result in an overflow.
The value of this bit is only meaningful when accessing PSR or APSR.
27
Q
RW
0
APSR DSP Overflow and Saturation Flag
Value Description
1
DSP Overflow or saturation has occurred when using a SIMD
instruction.
0
DSP overflow or saturation has not occurred since reset or since
the bit was last cleared.
The value of this bit is only meaningful when accessing PSR or APSR.
This bit is cleared by software using an MRS instruction.
June 12, 2014
77
Texas Instruments-Production Data
The Cortex-M4F Processor
Bit/Field
Name
Type
Reset
26:25
ICI / IT
RO
0x0
Description
EPSR ICI / IT status
These bits, along with bits 15:10, contain the Interruptible-Continuable
Instruction (ICI) field for an interrupted load multiple or store multiple
instruction or the execution state bits of the IT instruction.
When EPSR holds the ICI execution state, bits 26:25 are zero.
The If-Then block contains up to four instructions following an IT
instruction. Each instruction in the block is conditional. The conditions
for the instructions are either all the same, or some can be the inverse
of others. See the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI
0553A) for more information.
The value of this field is only meaningful when accessing PSR or EPSR.
Note that these EPSR bits cannot be accessed using MRS and MSR
instructions but the definitions are provided to allow the stacked (E)PSR
value to be decoded within an exception handler.
24
THUMB
RO
1
EPSR Thumb State
This bit indicates the Thumb state and should always be set.
The following can clear the THUMB bit:
■
The BLX, BX and POP{PC} instructions
■
Restoration from the stacked xPSR value on an exception return
■
Bit 0 of the vector value on an exception entry or reset
Attempting to execute instructions when this bit is clear results in a fault
or lockup. See “Lockup” on page 108 for more information.
The value of this bit is only meaningful when accessing PSR or EPSR.
23:20
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
19:16
GE
RW
0x0
Greater Than or Equal Flags
See the description of the SEL instruction in the Cortex™-M4 instruction
set chapter in the ARM® Cortex™-M4 Devices Generic User Guide
(literature number ARM DUI 0553A) for more information.
The value of this field is only meaningful when accessing PSR or APSR.
78
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
15:10
ICI / IT
RO
0x0
Description
EPSR ICI / IT status
These bits, along with bits 26:25, contain the Interruptible-Continuable
Instruction (ICI) field for an interrupted load multiple or store multiple
instruction or the execution state bits of the IT instruction.
When an interrupt occurs during the execution of an LDM, STM, PUSH
POP, VLDM, VSTM, VPUSH, or VPOP instruction, the processor stops the
load multiple or store multiple instruction operation temporarily and
stores the next register operand in the multiple operation to bits 15:12.
After servicing the interrupt, the processor returns to the register pointed
to by bits 15:12 and resumes execution of the multiple load or store
instruction. When EPSR holds the ICI execution state, bits 11:10 are
zero.
The If-Then block contains up to four instructions following a 16-bit IT
instruction. Each instruction in the block is conditional. The conditions
for the instructions are either all the same, or some can be the inverse
of others. See the Cortex™-M4 instruction set chapter in the ARM®
Cortex™-M4 Devices Generic User Guide (literature number ARM DUI
0553A) for more information.
The value of this field is only meaningful when accessing PSR or EPSR.
9:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:0
ISRNUM
RO
0x00
IPSR ISR Number
This field contains the exception type number of the current Interrupt
Service Routine (ISR).
Value
Description
0x00
Thread mode
0x01
Reserved
0x02
NMI
0x03
Hard fault
0x04
Memory management fault
0x05
Bus fault
0x06
Usage fault
0x07-0x0A Reserved
0x0B
SVCall
0x0C
Reserved for Debug
0x0D
Reserved
0x0E
PendSV
0x0F
SysTick
0x10
Interrupt Vector 0
0x11
Interrupt Vector 1
...
...
0x9A
Interrupt Vector 138
See “Exception Types” on page 97 for more information.
The value of this field is only meaningful when accessing PSR or IPSR.
June 12, 2014
79
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 18: Priority Mask Register (PRIMASK)
The PRIMASK register prevents activation of all exceptions with programmable priority. Reset,
non-maskable interrupt (NMI), and hard fault are the only exceptions with fixed priority. Exceptions
should be disabled when they might impact the timing of critical tasks. This register is only accessible
in privileged mode. The MSR and MRS instructions are used to access the PRIMASK register, and
the CPS instruction may be used to change the value of the PRIMASK register. See the Cortex™-M4
instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide (literature number
ARM DUI 0553A) for more information on these instructions. For more information on exception
priority levels, see “Exception Types” on page 97.
Priority Mask Register (PRIMASK)
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0x0000.000
0
PRIMASK
RW
0
RO
0
PRIMASK
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Priority Mask
Value Description
1
Prevents the activation of all exceptions with configurable
priority.
0
No effect.
80
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 19: Fault Mask Register (FAULTMASK)
The FAULTMASK register prevents activation of all exceptions except for the Non-Maskable Interrupt
(NMI). Exceptions should be disabled when they might impact the timing of critical tasks. This register
is only accessible in privileged mode. The MSR and MRS instructions are used to access the
FAULTMASK register, and the CPS instruction may be used to change the value of the FAULTMASK
register. See the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic
User Guide (literature number ARM DUI 0553A) for more information on these instructions. For
more information on exception priority levels, see “Exception Types” on page 97.
Fault Mask Register (FAULTMASK)
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0x0000.000
0
FAULTMASK
RW
0
RO
0
FAULTMASK
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Fault Mask
Value Description
1
Prevents the activation of all exceptions except for NMI.
0
No effect.
The processor clears the FAULTMASK bit on exit from any exception
handler except the NMI handler.
June 12, 2014
81
Texas Instruments-Production Data
The Cortex-M4F Processor
Register 20: Base Priority Mask Register (BASEPRI)
The BASEPRI register defines the minimum priority for exception processing. When BASEPRI is
set to a nonzero value, it prevents the activation of all exceptions with the same or lower priority
level as the BASEPRI value. Exceptions should be disabled when they might impact the timing of
critical tasks. This register is only accessible in privileged mode. For more information on exception
priority levels, see “Exception Types” on page 97.
Base Priority Mask Register (BASEPRI)
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
BASEPRI
RO
0
Bit/Field
Name
Type
Reset
31:8
reserved
RO
0x0000.00
7:5
BASEPRI
RW
0x0
RW
0
reserved
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Base Priority
Any exception that has a programmable priority level with the same or
lower priority as the value of this field is masked. The PRIMASK register
can be used to mask all exceptions with programmable priority levels.
Higher priority exceptions have lower priority levels.
Value Description
4:0
reserved
RO
0x0
0x0
All exceptions are unmasked.
0x1
All exceptions with priority level 1-7 are masked.
0x2
All exceptions with priority level 2-7 are masked.
0x3
All exceptions with priority level 3-7 are masked.
0x4
All exceptions with priority level 4-7 are masked.
0x5
All exceptions with priority level 5-7 are masked.
0x6
All exceptions with priority level 6-7 are masked.
0x7
All exceptions with priority level 7 are masked.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
82
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 21: Control Register (CONTROL)
The CONTROL register controls the stack used and the privilege level for software execution when
the processor is in Thread mode, and indicates whether the FPU state is active. This register is only
accessible in privileged mode.
Handler mode always uses the MSP, so the processor ignores explicit writes to the ASP bit of the
CONTROL register when in Handler mode. The exception entry and return mechanisms automatically
update the CONTROL register based on the EXC_RETURN value (see Table 2-10 on page 106).
In an OS environment, threads running in Thread mode should use the process stack and the kernel
and exception handlers should use the main stack. By default, Thread mode uses the MSP. To
switch the stack pointer used in Thread mode to the PSP, either use the MSR instruction to set the
ASP bit, as detailed in the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices
Generic User Guide (literature number ARM DUI 0553A), or perform an exception return to Thread
mode with the appropriate EXC_RETURN value, as shown in Table 2-10 on page 106.
Note:
When changing the stack pointer, software must use an ISB instruction immediately after
the MSR instruction, ensuring that instructions after the ISB execute use the new stack
pointer. See the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices
Generic User Guide (literature number ARM DUI 0553A).
Control Register (CONTROL)
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
FPCA
ASP
TMPL
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
2
FPCA
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Floating-Point Context Active
Value Description
1
Floating-point context active
0
No floating-point context active
The Cortex-M4F uses this bit to determine whether to preserve
floating-point state when processing an exception.
Important:
Two bits control when FPCA can be enabled: the ASPEN
bit in the Floating-Point Context Control (FPCC)
register and the DISFPCA bit in the Auxiliary Control
(ACTLR) register.
June 12, 2014
83
Texas Instruments-Production Data
The Cortex-M4F Processor
Bit/Field
Name
Type
Reset
1
ASP
RW
0
Description
Active Stack Pointer
Value Description
1
The PSP is the current stack pointer.
0
The MSP is the current stack pointer
In Handler mode, this bit reads as zero and ignores writes. The
Cortex-M4F updates this bit automatically on exception return.
0
TMPL
RW
0
Thread Mode Privilege Level
Value Description
1
Unprivileged software can be executed in Thread mode.
0
Only privileged software can be executed in Thread mode.
84
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 22: Floating-Point Status Control (FPSC)
The FPSC register provides all necessary user-level control of the floating-point system.
Floating-Point Status Control (FPSC)
Type RW, reset 31
Type
Reset
30
29
28
27
26
25
24
22
21
20
19
RMODE
18
17
16
N
Z
C
V
reserved
AHP
DN
FZ
RW
-
RW
-
RW
-
RW
-
RO
0
RW
-
RW
-
RW
-
RW
-
RW
-
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
IXC
UFC
OFC
DZC
IOC
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
-
RW
-
RW
-
RW
-
RW
-
reserved
Type
Reset
23
IDC
RO
0
Bit/Field
Name
Type
Reset
31
N
RW
-
RW
-
reserved
reserved
RO
0
RO
0
Description
Negative Condition Code Flag
Floating-point comparison operations update this condition code flag.
30
Z
RW
-
Zero Condition Code Flag
Floating-point comparison operations update this condition code flag.
29
C
RW
-
Carry Condition Code Flag
Floating-point comparison operations update this condition code flag.
28
V
RW
-
Overflow Condition Code Flag
Floating-point comparison operations update this condition code flag.
27
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
26
AHP
RW
-
Alternative Half-Precision
When set, alternative half-precision format is selected. When clear,
IEEE half-precision format is selected.
The AHP bit in the FPDSC register holds the default value for this bit.
25
DN
RW
-
Default NaN Mode
When set, any operation involving one or more NaNs returns the Default
NaN. When clear, NaN operands propagate through to the output of a
floating-point operation.
The DN bit in the FPDSC register holds the default value for this bit.
24
FZ
RW
-
Flush-to-Zero Mode
When set, Flush-to-Zero mode is enabled. When clear, Flush-to-Zero
mode is disabled and the behavior of the floating-point system is fully
compliant with the IEEE 754 standard.
The FZ bit in the FPDSC register holds the default value for this bit.
June 12, 2014
85
Texas Instruments-Production Data
The Cortex-M4F Processor
Bit/Field
Name
Type
Reset
23:22
RMODE
RW
-
Description
Rounding Mode
The specified rounding mode is used by almost all floating-point
instructions.
The RMODE bit in the FPDSC register holds the default value for this bit.
Value Description
21:8
reserved
RO
0x0
7
IDC
RW
-
0x0
Round to Nearest (RN) mode
0x1
Round towards Plus Infinity (RP) mode
0x2
Round towards Minus Infinity (RM) mode
0x3
Round towards Zero (RZ) mode
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Input Denormal Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
6:5
reserved
RO
0x0
4
IXC
RW
-
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Inexact Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
3
UFC
RW
-
Underflow Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
2
OFC
RW
-
Overflow Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
1
DZC
RW
-
Division by Zero Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
0
IOC
RW
-
Invalid Operation Cumulative Exception
When set, indicates this exception has occurred since 0 was last written
to this bit.
86
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
2.3.5
Exceptions and Interrupts
The Cortex-M4F processor supports interrupts and system exceptions. The processor and the
Nested Vectored Interrupt Controller (NVIC) prioritize and handle all exceptions. An exception
changes the normal flow of software control. The processor uses Handler mode to handle all
exceptions except for reset. See “Exception Entry and Return” on page 103 for more information.
The NVIC registers control interrupt handling. See “Nested Vectored Interrupt Controller
(NVIC)” on page 119 for more information.
2.3.6
Data Types
The Cortex-M4F supports 32-bit words, 16-bit halfwords, and 8-bit bytes. The processor also supports
64-bit data transfer instructions. All instruction and data memory accesses are little endian. See
“Memory Regions, Types and Attributes” on page 90 for more information.
2.4
Memory Model
This section describes the processor memory map, the behavior of memory accesses, and the
bit-banding features. The processor has a fixed memory map that provides up to 4 GB of addressable
memory.
The memory map for the TM4C123BE6PM controller is provided in Table 2-4 on page 87. In this
manual, register addresses are given as a hexadecimal increment, relative to the module's base
address as shown in the memory map.
The regions for SRAM and peripherals include bit-band regions. Bit-banding provides atomic
operations to bit data (see “Bit-Banding” on page 92).
The processor reserves regions of the Private peripheral bus (PPB) address range for core peripheral
registers (see “Cortex-M4 Peripherals” on page 117).
Note:
Within the memory map, attempts to read or write addresses in reserved spaces result in
a bus fault. In addition, attempts to write addresses in the flash range also result in a bus
fault.
Table 2-4. Memory Map
Start
End
Description
For details,
see page ...
0x0000.0000
0x0001.FFFF
On-chip Flash
527
0x0002.0000
0x1FFF.FFFF
Reserved
-
0x2000.0000
0x2000.7FFF
Bit-banded on-chip SRAM
513
0x2000.8000
0x21FF.FFFF
Reserved
-
0x2200.0000
0x220F.FFFF
Bit-band alias of bit-banded on-chip SRAM starting at
0x2000.0000
513
0x2210.0000
0x3FFF.FFFF
Reserved
-
0x4000.0000
0x4000.0FFF
Watchdog timer 0
763
0x4000.1000
0x4000.1FFF
Watchdog timer 1
763
0x4000.2000
0x4000.3FFF
Reserved
-
0x4000.4000
0x4000.4FFF
GPIO Port A
645
0x4000.5000
0x4000.5FFF
GPIO Port B
645
Memory
Peripherals
June 12, 2014
87
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-4. Memory Map (continued)
Start
End
Description
For details,
see page ...
0x4000.6000
0x4000.6FFF
GPIO Port C
645
0x4000.7000
0x4000.7FFF
GPIO Port D
645
0x4000.8000
0x4000.8FFF
SSI0
954
0x4000.9000
0x4000.9FFF
SSI1
954
0x4000.A000
0x4000.AFFF
SSI2
954
0x4000.B000
0x4000.BFFF
SSI3
954
0x4000.C000
0x4000.CFFF
UART0
890
0x4000.D000
0x4000.DFFF
UART1
890
0x4000.E000
0x4000.EFFF
UART2
890
0x4000.F000
0x4000.FFFF
UART3
890
0x4001.0000
0x4001.0FFF
UART4
890
0x4001.1000
0x4001.1FFF
UART5
890
0x4001.2000
0x4001.2FFF
UART6
890
0x4001.3000
0x4001.3FFF
UART7
890
0x4001.4000
0x4001.FFFF
Reserved
-
0x4002.0FFF
I2C 0
1004
0x4002.1FFF
I2C
1
1004
0x4002.2000
0x4002.2FFF
I2C
2
1004
0x4002.3000
0x4002.3FFF
I2C 3
1004
0x4002.4000
0x4002.4FFF
GPIO Port E
645
0x4002.5000
0x4002.5FFF
GPIO Port F
645
0x4002.6000
0x4002.7FFF
Reserved
-
0x4002.8000
0x4002.8FFF
PWM 0
1111
0x4002.9000
0x4002.9FFF
PWM 1
1111
0x4002.A000
0x4002.BFFF
Reserved
-
0x4002.C000
0x4002.CFFF
QEI0
1181
0x4002.D000
0x4002.DFFF
QEI1
1181
0x4002.E000
0x4002.FFFF
Reserved
-
0x4003.0000
0x4003.0FFF
16/32-bit Timer 0
712
0x4003.1000
0x4003.1FFF
16/32-bit Timer 1
712
0x4003.2000
0x4003.2FFF
16/32-bit Timer 2
712
0x4003.3000
0x4003.3FFF
16/32-bit Timer 3
712
0x4003.4000
0x4003.4FFF
16/32-bit Timer 4
712
0x4003.5000
0x4003.5FFF
16/32-bit Timer 5
712
0x4003.6000
0x4003.6FFF
32/64-bit Timer 0
712
0x4003.7000
0x4003.7FFF
32/64-bit Timer 1
712
0x4003.8000
0x4003.8FFF
ADC0
805
0x4003.9000
0x4003.9FFF
ADC1
805
0x4003.A000
0x4003.BFFF
Reserved
-
0x4003.C000
0x4003.CFFF
Analog Comparators
1091
Peripherals
0x4002.0000
0x4002.1000
88
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-4. Memory Map (continued)
Start
End
Description
For details,
see page ...
0x4003.D000
0x4003.FFFF
Reserved
-
0x4004.0000
0x4004.0FFF
CAN0 Controller
1054
0x4004.1000
0x4004.1FFF
CAN1 Controller
1054
0x4004.2000
0x4004.BFFF
Reserved
-
0x4004.C000
0x4004.CFFF
32/64-bit Timer 2
712
0x4004.D000
0x4004.DFFF
32/64-bit Timer 3
712
0x4004.E000
0x4004.EFFF
32/64-bit Timer 4
712
0x4004.F000
0x4004.FFFF
32/64-bit Timer 5
712
0x4005.0000
0x4005.7FFF
Reserved
-
0x4005.8000
0x4005.8FFF
GPIO Port A (AHB aperture)
645
0x4005.9000
0x4005.9FFF
GPIO Port B (AHB aperture)
645
0x4005.A000
0x4005.AFFF
GPIO Port C (AHB aperture)
645
0x4005.B000
0x4005.BFFF
GPIO Port D (AHB aperture)
645
0x4005.C000
0x4005.CFFF
GPIO Port E (AHB aperture)
645
0x4005.D000
0x4005.DFFF
GPIO Port F (AHB aperture)
645
0x4005.E000
0x400A.EFFF
Reserved
-
0x400A.F000
0x400A.FFFF
EEPROM and Key Locker
527
0x400B.0000
0x400F.8FFF
Reserved
-
0x400F.9000
0x400F.9FFF
System Exception Module
473
0x400F.A000
0x400F.BFFF
Reserved
-
0x400F.C000
0x400F.CFFF
Hibernation Module
493
0x400F.D000
0x400F.DFFF
Flash memory control
527
0x400F.E000
0x400F.EFFF
System control
226
0x400F.F000
0x400F.FFFF
µDMA
593
0x4010.0000
0x41FF.FFFF
Reserved
-
0x4200.0000
0x43FF.FFFF
Bit-banded alias of 0x4000.0000 through 0x400F.FFFF
-
0x4400.0000
0xDFFF.FFFF
Reserved
-
0xE000.0000
0xE000.0FFF
Instrumentation Trace Macrocell (ITM)
66
0xE000.1000
0xE000.1FFF
Data Watchpoint and Trace (DWT)
66
0xE000.2000
0xE000.2FFF
Flash Patch and Breakpoint (FPB)
66
0xE000.3000
0xE000.DFFF
Reserved
-
0xE000.E000
0xE000.EFFF
Cortex-M4F Peripherals (SysTick, NVIC, MPU, FPU and SCB) 129
0xE000.F000
0xE003.FFFF
Reserved
-
0xE004.0000
0xE004.0FFF
Trace Port Interface Unit (TPIU)
67
0xE004.1000
0xE004.1FFF
Embedded Trace Macrocell (ETM)
66
0xE004.2000
0xFFFF.FFFF
Reserved
-
Private Peripheral Bus
June 12, 2014
89
Texas Instruments-Production Data
The Cortex-M4F Processor
2.4.1
Memory Regions, Types and Attributes
The memory map and the programming of the MPU split the memory map into regions. Each region
has a defined memory type, and some regions have additional memory attributes. The memory
type and attributes determine the behavior of accesses to the region.
The memory types are:
■ Normal: The processor can re-order transactions for efficiency and perform speculative reads.
■ Device: The processor preserves transaction order relative to other transactions to Device or
Strongly Ordered memory.
■ Strongly Ordered: The processor preserves transaction order relative to all other transactions.
The different ordering requirements for Device and Strongly Ordered memory mean that the memory
system can buffer a write to Device memory but must not buffer a write to Strongly Ordered memory.
An additional memory attribute is Execute Never (XN), which means the processor prevents
instruction accesses. A fault exception is generated only on execution of an instruction executed
from an XN region.
2.4.2
Memory System Ordering of Memory Accesses
For most memory accesses caused by explicit memory access instructions, the memory system
does not guarantee that the order in which the accesses complete matches the program order of
the instructions, providing the order does not affect the behavior of the instruction sequence. Normally,
if correct program execution depends on two memory accesses completing in program order,
software must insert a memory barrier instruction between the memory access instructions (see
“Software Ordering of Memory Accesses” on page 91).
However, the memory system does guarantee ordering of accesses to Device and Strongly Ordered
memory. For two memory access instructions A1 and A2, if both A1 and A2 are accesses to either
Device or Strongly Ordered memory, and if A1 occurs before A2 in program order, A1 is always
observed before A2.
2.4.3
Behavior of Memory Accesses
Table 2-5 on page 90 shows the behavior of accesses to each region in the memory map. See
“Memory Regions, Types and Attributes” on page 90 for more information on memory types and
the XN attribute. Tiva™ C Series devices may have reserved memory areas within the address
ranges shown below (refer to Table 2-4 on page 87 for more information).
Table 2-5. Memory Access Behavior
Address Range
Memory Region
Memory Type
Execute
Never
(XN)
Description
0x0000.0000 - 0x1FFF.FFFF Code
Normal
-
This executable region is for program code.
Data can also be stored here.
0x2000.0000 - 0x3FFF.FFFF SRAM
Normal
-
This executable region is for data. Code
can also be stored here. This region
includes bit band and bit band alias areas
(see Table 2-6 on page 92).
0x4000.0000 - 0x5FFF.FFFF Peripheral
Device
XN
This region includes bit band and bit band
alias areas (see Table 2-7 on page 93).
0x6000.0000 - 0x9FFF.FFFF External RAM
Normal
-
This executable region is for data.
90
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-5. Memory Access Behavior (continued)
Address Range
Memory Region
Memory Type
Execute
Never
(XN)
Description
0xA000.0000 - 0xDFFF.FFFF External device
Device
XN
This region is for external device memory.
0xE000.0000- 0xE00F.FFFF Private peripheral
bus
Strongly
Ordered
XN
This region includes the NVIC, system
timer, and system control block.
0xE010.0000- 0xFFFF.FFFF Reserved
-
-
-
The Code, SRAM, and external RAM regions can hold programs. However, it is recommended that
programs always use the Code region because the Cortex-M4F has separate buses that can perform
instruction fetches and data accesses simultaneously.
The MPU can override the default memory access behavior described in this section. For more
information, see “Memory Protection Unit (MPU)” on page 120.
The Cortex-M4F prefetches instructions ahead of execution and speculatively prefetches from
branch target addresses.
2.4.4
Software Ordering of Memory Accesses
The order of instructions in the program flow does not always guarantee the order of the
corresponding memory transactions for the following reasons:
■ The processor can reorder some memory accesses to improve efficiency, providing this does
not affect the behavior of the instruction sequence.
■ The processor has multiple bus interfaces.
■ Memory or devices in the memory map have different wait states.
■ Some memory accesses are buffered or speculative.
“Memory System Ordering of Memory Accesses” on page 90 describes the cases where the memory
system guarantees the order of memory accesses. Otherwise, if the order of memory accesses is
critical, software must include memory barrier instructions to force that ordering. The Cortex-M4F
has the following memory barrier instructions:
■ The Data Memory Barrier (DMB) instruction ensures that outstanding memory transactions
complete before subsequent memory transactions.
■ The Data Synchronization Barrier (DSB) instruction ensures that outstanding memory transactions
complete before subsequent instructions execute.
■ The Instruction Synchronization Barrier (ISB) instruction ensures that the effect of all completed
memory transactions is recognizable by subsequent instructions.
Memory barrier instructions can be used in the following situations:
■ MPU programming
– If the MPU settings are changed and the change must be effective on the very next instruction,
use a DSB instruction to ensure the effect of the MPU takes place immediately at the end of
context switching.
June 12, 2014
91
Texas Instruments-Production Data
The Cortex-M4F Processor
– Use an ISB instruction to ensure the new MPU setting takes effect immediately after
programming the MPU region or regions, if the MPU configuration code was accessed using
a branch or call. If the MPU configuration code is entered using exception mechanisms, then
an ISB instruction is not required.
■ Vector table
If the program changes an entry in the vector table and then enables the corresponding exception,
use a DMB instruction between the operations. The DMB instruction ensures that if the exception
is taken immediately after being enabled, the processor uses the new exception vector.
■ Self-modifying code
If a program contains self-modifying code, use an ISB instruction immediately after the code
modification in the program. The ISB instruction ensures subsequent instruction execution uses
the updated program.
■ Memory map switching
If the system contains a memory map switching mechanism, use a DSB instruction after switching
the memory map in the program. The DSB instruction ensures subsequent instruction execution
uses the updated memory map.
■ Dynamic exception priority change
When an exception priority has to change when the exception is pending or active, use DSB
instructions after the change. The change then takes effect on completion of the DSB instruction.
Memory accesses to Strongly Ordered memory, such as the System Control Block, do not require
the use of DMB instructions.
For more information on the memory barrier instructions, see the Cortex™-M4 instruction set chapter
in the ARM® Cortex™-M4 Devices Generic User Guide (literature number ARM DUI 0553A).
2.4.5
Bit-Banding
A bit-band region maps each word in a bit-band alias region to a single bit in the bit-band region.
The bit-band regions occupy the lowest 1 MB of the SRAM and peripheral memory regions. Accesses
to the 32-MB SRAM alias region map to the 1-MB SRAM bit-band region, as shown in Table
2-6 on page 92. Accesses to the 32-MB peripheral alias region map to the 1-MB peripheral bit-band
region, as shown in Table 2-7 on page 93. For the specific address range of the bit-band regions,
see Table 2-4 on page 87.
Note:
A word access to the SRAM or the peripheral bit-band alias region maps to a single bit in
the SRAM or peripheral bit-band region.
A word access to a bit band address results in a word access to the underlying memory,
and similarly for halfword and byte accesses. This allows bit band accesses to match the
access requirements of the underlying peripheral.
Table 2-6. SRAM Memory Bit-Banding Regions
Address Range
Memory Region
Start
End
0x2000.0000
0x2000.7FFF
Instruction and Data Accesses
SRAM bit-band region Direct accesses to this memory range behave as SRAM
memory accesses, but this region is also bit addressable
through bit-band alias.
92
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-6. SRAM Memory Bit-Banding Regions (continued)
Address Range
Start
End
0x2200.0000
0x220F.FFFF
Memory Region
Instruction and Data Accesses
SRAM bit-band alias
Data accesses to this region are remapped to bit band
region. A write operation is performed as
read-modify-write. Instruction accesses are not remapped.
Table 2-7. Peripheral Memory Bit-Banding Regions
Address Range
Memory Region
Instruction and Data Accesses
0x400F.FFFF
Peripheral bit-band
region
Direct accesses to this memory range behave as
peripheral memory accesses, but this region is also bit
addressable through bit-band alias.
0x43FF.FFFF
Peripheral bit-band alias Data accesses to this region are remapped to bit band
region. A write operation is performed as
read-modify-write. Instruction accesses are not permitted.
Start
End
0x4000.0000
0x4200.0000
The following formula shows how the alias region maps onto the bit-band region:
bit_word_offset = (byte_offset x 32) + (bit_number x 4)
bit_word_addr = bit_band_base + bit_word_offset
where:
bit_word_offset
The position of the target bit in the bit-band memory region.
bit_word_addr
The address of the word in the alias memory region that maps to the targeted bit.
bit_band_base
The starting address of the alias region.
byte_offset
The number of the byte in the bit-band region that contains the targeted bit.
bit_number
The bit position, 0-7, of the targeted bit.
Figure 2-4 on page 94 shows examples of bit-band mapping between the SRAM bit-band alias
region and the SRAM bit-band region:
■ The alias word at 0x23FF.FFE0 maps to bit 0 of the bit-band byte at 0x200F.FFFF:
0x23FF.FFE0 = 0x2200.0000 + (0x000F.FFFF*32) + (0*4)
■ The alias word at 0x23FF.FFFC maps to bit 7 of the bit-band byte at 0x200F.FFFF:
0x23FF.FFFC = 0x2200.0000 + (0x000F.FFFF*32) + (7*4)
■ The alias word at 0x2200.0000 maps to bit 0 of the bit-band byte at 0x2000.0000:
June 12, 2014
93
Texas Instruments-Production Data
The Cortex-M4F Processor
0x2200.0000 = 0x2200.0000 + (0*32) + (0*4)
■ The alias word at 0x2200.001C maps to bit 7 of the bit-band byte at 0x2000.0000:
0x2200.001C = 0x2200.0000+ (0*32) + (7*4)
Figure 2-4. Bit-Band Mapping
32-MB Alias Region
0x23FF.FFFC
0x23FF.FFF8
0x23FF.FFF4
0x23FF.FFF0
0x23FF.FFEC
0x23FF.FFE8
0x23FF.FFE4
0x23FF.FFE0
0x2200.001C
0x2200.0018
0x2200.0014
0x2200.0010
0x2200.000C
0x2200.0008
0x2200.0004
0x2200.0000
7
3
1-MB SRAM Bit-Band Region
7
6
5
4
3
2
1
0
7
6
0x200F.FFFF
7
6
5
4
3
2
0x2000.0003
2.4.5.1
5
4
3
2
1
0
7
6
0x200F.FFFE
1
0
7
6
5
4
3
2
5
4
3
2
1
0
6
0x200F.FFFD
1
0
0x2000.0002
7
6
5
4
3
2
0x2000.0001
5
4
2
1
0
1
0
0x200F.FFFC
1
0
7
6
5
4
3
2
0x2000.0000
Directly Accessing an Alias Region
Writing to a word in the alias region updates a single bit in the bit-band region.
Bit 0 of the value written to a word in the alias region determines the value written to the targeted
bit in the bit-band region. Writing a value with bit 0 set writes a 1 to the bit-band bit, and writing a
value with bit 0 clear writes a 0 to the bit-band bit.
Bits 31:1 of the alias word have no effect on the bit-band bit. Writing 0x01 has the same effect as
writing 0xFF. Writing 0x00 has the same effect as writing 0x0E.
When reading a word in the alias region, 0x0000.0000 indicates that the targeted bit in the bit-band
region is clear and 0x0000.0001 indicates that the targeted bit in the bit-band region is set.
2.4.5.2
Directly Accessing a Bit-Band Region
“Behavior of Memory Accesses” on page 90 describes the behavior of direct byte, halfword, or word
accesses to the bit-band regions.
2.4.6
Data Storage
The processor views memory as a linear collection of bytes numbered in ascending order from zero.
For example, bytes 0-3 hold the first stored word, and bytes 4-7 hold the second stored word. Data
is stored in little-endian format, with the least-significant byte (lsbyte) of a word stored at the
lowest-numbered byte, and the most-significant byte (msbyte) stored at the highest-numbered byte.
Figure 2-5 on page 95 illustrates how data is stored.
94
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Figure 2-5. Data Storage
Memory
7
Register
0
31
2.4.7
Address A
B0
A+1
B1
A+2
B2
A+3
B3
lsbyte
24 23
B3
16 15
B2
8 7
B1
0
B0
msbyte
Synchronization Primitives
The Cortex-M4F instruction set includes pairs of synchronization primitives which provide a
non-blocking mechanism that a thread or process can use to obtain exclusive access to a memory
location. Software can use these primitives to perform a guaranteed read-modify-write memory
update sequence or for a semaphore mechanism.
A pair of synchronization primitives consists of:
■ A Load-Exclusive instruction, which is used to read the value of a memory location and requests
exclusive access to that location.
■ A Store-Exclusive instruction, which is used to attempt to write to the same memory location and
returns a status bit to a register. If this status bit is clear, it indicates that the thread or process
gained exclusive access to the memory and the write succeeds; if this status bit is set, it indicates
that the thread or process did not gain exclusive access to the memory and no write was
performed.
The pairs of Load-Exclusive and Store-Exclusive instructions are:
■ The word instructions LDREX and STREX
■ The halfword instructions LDREXH and STREXH
■ The byte instructions LDREXB and STREXB
Software must use a Load-Exclusive instruction with the corresponding Store-Exclusive instruction.
To perform an exclusive read-modify-write of a memory location, software must:
1. Use a Load-Exclusive instruction to read the value of the location.
2. Modify the value, as required.
3. Use a Store-Exclusive instruction to attempt to write the new value back to the memory location.
4. Test the returned status bit.
If the status bit is clear, the read-modify-write completed successfully. If the status bit is set, no
write was performed, which indicates that the value returned at step 1 might be out of date. The
software must retry the entire read-modify-write sequence.
Software can use the synchronization primitives to implement a semaphore as follows:
June 12, 2014
95
Texas Instruments-Production Data
The Cortex-M4F Processor
1. Use a Load-Exclusive instruction to read from the semaphore address to check whether the
semaphore is free.
2. If the semaphore is free, use a Store-Exclusive to write the claim value to the semaphore
address.
3. If the returned status bit from step 2 indicates that the Store-Exclusive succeeded, then the
software has claimed the semaphore. However, if the Store-Exclusive failed, another process
might have claimed the semaphore after the software performed step 1.
The Cortex-M4F includes an exclusive access monitor that tags the fact that the processor has
executed a Load-Exclusive instruction. The processor removes its exclusive access tag if:
■ It executes a CLREX instruction.
■ It executes a Store-Exclusive instruction, regardless of whether the write succeeds.
■ An exception occurs, which means the processor can resolve semaphore conflicts between
different threads.
For more information about the synchronization primitive instructions, see the Cortex™-M4 instruction
set chapter in the ARM® Cortex™-M4 Devices Generic User Guide (literature number ARM DUI
0553A).
2.5
Exception Model
The ARM Cortex-M4F processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and
handle all exceptions in Handler Mode. The processor state is automatically stored to the stack on
an exception and automatically restored from the stack at the end of the Interrupt Service Routine
(ISR). The vector is fetched in parallel to the state saving, enabling efficient interrupt entry. The
processor supports tail-chaining, which enables back-to-back interrupts to be performed without the
overhead of state saving and restoration.
Table 2-8 on page 98 lists all exception types. Software can set eight priority levels on seven of
these exceptions (system handlers) as well as on 77 interrupts (listed in Table 2-9 on page 99).
Priorities on the system handlers are set with the NVIC System Handler Priority n (SYSPRIn)
registers. Interrupts are enabled through the NVIC Interrupt Set Enable n (ENn) register and
prioritized with the NVIC Interrupt Priority n (PRIn) registers. Priorities can be grouped by splitting
priority levels into preemption priorities and subpriorities. All the interrupt registers are described in
“Nested Vectored Interrupt Controller (NVIC)” on page 119.
Internally, the highest user-programmable priority (0) is treated as fourth priority, after a Reset,
Non-Maskable Interrupt (NMI), and a Hard Fault, in that order. Note that 0 is the default priority for
all the programmable priorities.
Important: After a write to clear an interrupt source, it may take several processor cycles for the
NVIC to see the interrupt source deassert. Thus if the interrupt clear is done as the last
action in an interrupt handler, it is possible for the interrupt handler to complete while
the NVIC sees the interrupt as still asserted, causing the interrupt handler to be
re-entered errantly. This situation can be avoided by either clearing the interrupt source
at the beginning of the interrupt handler or by performing a read or write after the write
to clear the interrupt source (and flush the write buffer).
See “Nested Vectored Interrupt Controller (NVIC)” on page 119 for more information on exceptions
and interrupts.
96
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
2.5.1
Exception States
Each exception is in one of the following states:
■ Inactive. The exception is not active and not pending.
■ Pending. The exception is waiting to be serviced by the processor. An interrupt request from a
peripheral or from software can change the state of the corresponding interrupt to pending.
■ Active. An exception that is being serviced by the processor but has not completed.
Note:
An exception handler can interrupt the execution of another exception handler. In this
case, both exceptions are in the active state.
■ Active and Pending. The exception is being serviced by the processor, and there is a pending
exception from the same source.
2.5.2
Exception Types
The exception types are:
■ Reset. Reset is invoked on power up or a warm reset. The exception model treats reset as a
special form of exception. When reset is asserted, the operation of the processor stops, potentially
at any point in an instruction. When reset is deasserted, execution restarts from the address
provided by the reset entry in the vector table. Execution restarts as privileged execution in
Thread mode.
■ NMI. A non-maskable Interrupt (NMI) can be signaled using the NMI signal or triggered by
software using the Interrupt Control and State (INTCTRL) register. This exception has the
highest priority other than reset. NMI is permanently enabled and has a fixed priority of -2. NMIs
cannot be masked or prevented from activation by any other exception or preempted by any
exception other than reset.
■ Hard Fault. A hard fault is an exception that occurs because of an error during exception
processing, or because an exception cannot be managed by any other exception mechanism.
Hard faults have a fixed priority of -1, meaning they have higher priority than any exception with
configurable priority.
■ Memory Management Fault. A memory management fault is an exception that occurs because
of a memory protection related fault, including access violation and no match. The MPU or the
fixed memory protection constraints determine this fault, for both instruction and data memory
transactions. This fault is used to abort instruction accesses to Execute Never (XN) memory
regions, even if the MPU is disabled.
■ Bus Fault. A bus fault is an exception that occurs because of a memory-related fault for an
instruction or data memory transaction such as a prefetch fault or a memory access fault. This
fault can be enabled or disabled.
■ Usage Fault. A usage fault is an exception that occurs because of a fault related to instruction
execution, such as:
– An undefined instruction
– An illegal unaligned access
– Invalid state on instruction execution
June 12, 2014
97
Texas Instruments-Production Data
The Cortex-M4F Processor
– An error on exception return
An unaligned address on a word or halfword memory access or division by zero can cause a
usage fault when the core is properly configured.
■ SVCall. A supervisor call (SVC) is an exception that is triggered by the SVC instruction. In an
OS environment, applications can use SVC instructions to access OS kernel functions and device
drivers.
■ Debug Monitor. This exception is caused by the debug monitor (when not halting). This exception
is only active when enabled. This exception does not activate if it is a lower priority than the
current activation.
■ PendSV. PendSV is a pendable, interrupt-driven request for system-level service. In an OS
environment, use PendSV for context switching when no other exception is active. PendSV is
triggered using the Interrupt Control and State (INTCTRL) register.
■ SysTick. A SysTick exception is an exception that the system timer generates when it reaches
zero when it is enabled to generate an interrupt. Software can also generate a SysTick exception
using the Interrupt Control and State (INTCTRL) register. In an OS environment, the processor
can use this exception as system tick.
■ Interrupt (IRQ). An interrupt, or IRQ, is an exception signaled by a peripheral or generated by
a software request and fed through the NVIC (prioritized). All interrupts are asynchronous to
instruction execution. In the system, peripherals use interrupts to communicate with the processor.
Table 2-9 on page 99 lists the interrupts on the TM4C123BE6PM controller.
For an asynchronous exception, other than reset, the processor can execute another instruction
between when the exception is triggered and when the processor enters the exception handler.
Privileged software can disable the exceptions that Table 2-8 on page 98 shows as having
configurable priority (see the SYSHNDCTRL register on page 168 and the DIS0 register on page 139).
For more information about hard faults, memory management faults, bus faults, and usage faults,
see “Fault Handling” on page 106.
Table 2-8. Exception Types
Exception Type
a
Vector
Number
Priority
Vector Address or
b
Offset
-
0
-
0x0000.0000
Stack top is loaded from the first
entry of the vector table on reset.
Reset
1
-3 (highest)
0x0000.0004
Asynchronous
Non-Maskable Interrupt
(NMI)
2
-2
0x0000.0008
Asynchronous
Hard Fault
3
-1
0x0000.000C
-
c
0x0000.0010
Synchronous
c
0x0000.0014
Synchronous when precise and
asynchronous when imprecise
c
Synchronous
Memory Management
4
programmable
Bus Fault
5
programmable
Usage Fault
6
programmable
0x0000.0018
7-10
-
-
-
Activation
c
c
Reserved
SVCall
11
programmable
0x0000.002C
Synchronous
Debug Monitor
12
programmable
0x0000.0030
Synchronous
-
13
-
-
98
Reserved
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-8. Exception Types (continued)
Exception Type
PendSV
SysTick
a
Vector
Number
Priority
14
programmable
15
Interrupts
Vector Address or
b
Offset
c
0x0000.0038
Asynchronous
c
0x0000.003C
Asynchronous
programmable
16 and above
Activation
d
programmable
0x0000.0040 and above Asynchronous
a. 0 is the default priority for all the programmable priorities.
b. See “Vector Table” on page 101.
c. See SYSPRI1 on page 165.
d. See PRIn registers on page 147.
Table 2-9. Interrupts
Vector Number
Interrupt Number (Bit
in Interrupt Registers)
Vector Address or
Offset
Description
0-15
-
0x0000.0000 0x0000.003C
16
0
0x0000.0040
GPIO Port A
17
1
0x0000.0044
GPIO Port B
18
2
0x0000.0048
GPIO Port C
19
3
0x0000.004C
GPIO Port D
20
4
0x0000.0050
GPIO Port E
21
5
0x0000.0054
UART0
22
6
0x0000.0058
UART1
23
7
0x0000.005C
SSI0
24
8
0x0000.0060
I2C0
25
9
0x0000.0064
PWM0 Fault
26
10
0x0000.0068
PWM0 Generator 0
27
11
0x0000.006C
PWM0 Generator 1
28
12
0x0000.0070
PWM0 Generator 2
29
13
0x0000.0074
QEI0
30
14
0x0000.0078
ADC0 Sequence 0
31
15
0x0000.007C
ADC0 Sequence 1
32
16
0x0000.0080
ADC0 Sequence 2
33
17
0x0000.0084
ADC0 Sequence 3
34
18
0x0000.0088
Watchdog Timers 0 and 1
35
19
0x0000.008C
16/32-Bit Timer 0A
36
20
0x0000.0090
16/32-Bit Timer 0B
37
21
0x0000.0094
16/32-Bit Timer 1A
38
22
0x0000.0098
16/32-Bit Timer 1B
39
23
0x0000.009C
16/32-Bit Timer 2A
40
24
0x0000.00A0
16/32-Bit Timer 2B
41
25
0x0000.00A4
Analog Comparator 0
42
26
0x0000.00A8
Analog Comparator 1
43
27
-
44
28
0x0000.00B0
Processor exceptions
Reserved
System Control
June 12, 2014
99
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-9. Interrupts (continued)
Vector Number
Interrupt Number (Bit
in Interrupt Registers)
Vector Address or
Offset
Description
45
29
0x0000.00B4
Flash Memory Control and EEPROM Control
GPIO Port F
46
30
0x0000.00B8
47-48
31-32
-
49
33
0x0000.00C4
UART2
50
34
0x0000.00C8
SSI1
51
35
0x0000.00CC
16/32-Bit Timer 3A
52
36
0x0000.00D0
16/32-Bit Timer 3B
53
37
0x0000.00D4
I2C1
54
38
0x0000.00D8
QEI1
55
39
0x0000.00DC
CAN0
CAN1
Reserved
56
40
0x0000.00E0
57-58
41-42
-
59
43
0x0000.00EC
60
44
-
61
45
0x0000.00F4
PWM Generator 3
Reserved
Hibernation Module
Reserved
62
46
0x0000.00F8
µDMA Software
63
47
0x0000.00FC
µDMA Error
64
48
0x0000.0100
ADC1 Sequence 0
65
49
0x0000.0104
ADC1 Sequence 1
66
50
0x0000.0108
ADC1 Sequence 2
ADC1 Sequence 3
67
51
0x0000.010C
68-72
52-56
-
73
57
0x0000.0124
SSI2
74
58
0x0000.0128
SSI3
75
59
0x0000.012C
UART3
76
60
0x0000.0130
UART4
77
61
0x0000.0134
UART5
78
62
0x0000.0138
UART6
79
63
0x0000.013C
UART7
80-83
64-67
0x0000.0140 0x0000.014C
Reserved
84
68
0x0000.0150
I2C2
85
69
0x0000.0154
I2C3
86
70
0x0000.0158
16/32-Bit Timer 4A
Reserved
87
71
0x0000.015C
16/32-Bit Timer 4B
88-107
72-91
0x0000.0160 0x0000.01AC
Reserved
108
92
0x0000.01B0
16/32-Bit Timer 5A
109
93
0x0000.01B4
16/32-Bit Timer 5B
110
94
0x0000.01B8
32/64-Bit Timer 0A
111
95
0x0000.01BC
32/64-Bit Timer 0B
112
96
0x0000.01C0
32/64-Bit Timer 1A
100
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-9. Interrupts (continued)
2.5.3
Vector Number
Interrupt Number (Bit
in Interrupt Registers)
Vector Address or
Offset
Description
113
97
0x0000.01C4
32/64-Bit Timer 1B
114
98
0x0000.01C8
32/64-Bit Timer 2A
115
99
0x0000.01CC
32/64-Bit Timer 2B
116
100
0x0000.01D0
32/64-Bit Timer 3A
117
101
0x0000.01D4
32/64-Bit Timer 3B
118
102
0x0000.01D8
32/64-Bit Timer 4A
119
103
0x0000.01DC
32/64-Bit Timer 4B
120
104
0x0000.01E0
32/64-Bit Timer 5A
121
105
0x0000.01E4
32/64-Bit Timer 5B
122
106
0x0000.01E8
System Exception (imprecise)
123-149
107-133
-
150
134
0x0000.0258
PWM1 Generator 0
Reserved
151
135
0x0000.025C
PWM1 Generator 1
152
136
0x0000.0260
PWM1 Generator 2
153
137
0x0000.0264
PWM1 Generator 3
154
138
0x0000.0268
PWM1 Fault
Exception Handlers
The processor handles exceptions using:
■ Interrupt Service Routines (ISRs). Interrupts (IRQx) are the exceptions handled by ISRs.
■ Fault Handlers. Hard fault, memory management fault, usage fault, and bus fault are fault
exceptions handled by the fault handlers.
■ System Handlers. NMI, PendSV, SVCall, SysTick, and the fault exceptions are all system
exceptions that are handled by system handlers.
2.5.4
Vector Table
The vector table contains the reset value of the stack pointer and the start addresses, also called
exception vectors, for all exception handlers. The vector table is constructed using the vector address
or offset shown in Table 2-8 on page 98. Figure 2-6 on page 102 shows the order of the exception
vectors in the vector table. The least-significant bit of each vector must be 1, indicating that the
exception handler is Thumb code
June 12, 2014
101
Texas Instruments-Production Data
The Cortex-M4F Processor
Figure 2-6. Vector Table
Exception number IRQ number
154
138
.
.
.
18
2
17
1
16
0
15
-1
14
-2
13
Offset
0x0268
.
.
.
0x004C
0x0048
0x0044
0x0040
0x003C
0x0038
12
11
Vector
IRQ131
.
.
.
IRQ2
IRQ1
IRQ0
Systick
PendSV
Reserved
Reserved for Debug
-5
10
0x002C
9
SVCall
Reserved
8
7
6
-10
5
-11
4
-12
3
-13
2
-14
1
0x0018
0x0014
0x0010
0x000C
0x0008
0x0004
0x0000
Usage fault
Bus fault
Memory management fault
Hard fault
NMI
Reset
Initial SP value
On system reset, the vector table is fixed at address 0x0000.0000. Privileged software can write to
the Vector Table Offset (VTABLE) register to relocate the vector table start address to a different
memory location, in the range 0x0000.0400 to 0x3FFF.FC00 (see “Vector Table” on page 101). Note
that when configuring the VTABLE register, the offset must be aligned on a 1024-byte boundary.
2.5.5
Exception Priorities
As Table 2-8 on page 98 shows, all exceptions have an associated priority, with a lower priority
value indicating a higher priority and configurable priorities for all exceptions except Reset, Hard
fault, and NMI. If software does not configure any priorities, then all exceptions with a configurable
priority have a priority of 0. For information about configuring exception priorities, see page 165 and
page 147.
Note:
Configurable priority values for the Tiva™ C Series implementation are in the range 0-7.
This means that the Reset, Hard fault, and NMI exceptions, with fixed negative priority
values, always have higher priority than any other exception.
For example, assigning a higher priority value to IRQ[0] and a lower priority value to IRQ[1] means
that IRQ[1] has higher priority than IRQ[0]. If both IRQ[1] and IRQ[0] are asserted, IRQ[1] is processed
before IRQ[0].
102
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
If multiple pending exceptions have the same priority, the pending exception with the lowest exception
number takes precedence. For example, if both IRQ[0] and IRQ[1] are pending and have the same
priority, then IRQ[0] is processed before IRQ[1].
When the processor is executing an exception handler, the exception handler is preempted if a
higher priority exception occurs. If an exception occurs with the same priority as the exception being
handled, the handler is not preempted, irrespective of the exception number. However, the status
of the new interrupt changes to pending.
2.5.6
Interrupt Priority Grouping
To increase priority control in systems with interrupts, the NVIC supports priority grouping. This
grouping divides each interrupt priority register entry into two fields:
■ An upper field that defines the group priority
■ A lower field that defines a subpriority within the group
Only the group priority determines preemption of interrupt exceptions. When the processor is
executing an interrupt exception handler, another interrupt with the same group priority as the
interrupt being handled does not preempt the handler.
If multiple pending interrupts have the same group priority, the subpriority field determines the order
in which they are processed. If multiple pending interrupts have the same group priority and
subpriority, the interrupt with the lowest IRQ number is processed first.
For information about splitting the interrupt priority fields into group priority and subpriority, see
page 159.
2.5.7
Exception Entry and Return
Descriptions of exception handling use the following terms:
■ Preemption. When the processor is executing an exception handler, an exception can preempt
the exception handler if its priority is higher than the priority of the exception being handled. See
“Interrupt Priority Grouping” on page 103 for more information about preemption by an interrupt.
When one exception preempts another, the exceptions are called nested exceptions. See
“Exception Entry” on page 104 more information.
■ Return. Return occurs when the exception handler is completed, and there is no pending
exception with sufficient priority to be serviced and the completed exception handler was not
handling a late-arriving exception. The processor pops the stack and restores the processor
state to the state it had before the interrupt occurred. See “Exception Return” on page 105 for
more information.
■ Tail-Chaining. This mechanism speeds up exception servicing. On completion of an exception
handler, if there is a pending exception that meets the requirements for exception entry, the
stack pop is skipped and control transfers to the new exception handler.
■ Late-Arriving. This mechanism speeds up preemption. If a higher priority exception occurs
during state saving for a previous exception, the processor switches to handle the higher priority
exception and initiates the vector fetch for that exception. State saving is not affected by late
arrival because the state saved is the same for both exceptions. Therefore, the state saving
continues uninterrupted. The processor can accept a late arriving exception until the first instruction
of the exception handler of the original exception enters the execute stage of the processor. On
June 12, 2014
103
Texas Instruments-Production Data
The Cortex-M4F Processor
return from the exception handler of the late-arriving exception, the normal tail-chaining rules
apply.
2.5.7.1
Exception Entry
Exception entry occurs when there is a pending exception with sufficient priority and either the
processor is in Thread mode or the new exception is of higher priority than the exception being
handled, in which case the new exception preempts the original exception.
When one exception preempts another, the exceptions are nested.
Sufficient priority means the exception has more priority than any limits set by the mask registers
(see PRIMASK on page 80, FAULTMASK on page 81, and BASEPRI on page 82). An exception
with less priority than this is pending but is not handled by the processor.
When the processor takes an exception, unless the exception is a tail-chained or a late-arriving
exception, the processor pushes information onto the current stack. This operation is referred to as
stacking and the structure of eight data words is referred to as stack frame.
When using floating-point routines, the Cortex-M4F processor automatically stacks the architected
floating-point state on exception entry. Figure 2-7 on page 105 shows the Cortex-M4F stack frame
layout when floating-point state is preserved on the stack as the result of an interrupt or an exception.
Note:
Where stack space for floating-point state is not allocated, the stack frame is the same as
that of ARMv7-M implementations without an FPU. Figure 2-7 on page 105 shows this stack
frame also.
104
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Figure 2-7. Exception Stack Frame
...
{aligner}
FPSCR
S15
S14
S13
S12
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
xPSR
PC
LR
R12
R3
R2
R1
R0
Exception frame with
floating-point storage
Pre-IRQ top of stack
Decreasing
memory
address
IRQ top of stack
...
{aligner}
xPSR
PC
LR
R12
R3
R2
R1
R0
Pre-IRQ top of stack
IRQ top of stack
Exception frame without
floating-point storage
Immediately after stacking, the stack pointer indicates the lowest address in the stack frame.
The stack frame includes the return address, which is the address of the next instruction in the
interrupted program. This value is restored to the PC at exception return so that the interrupted
program resumes.
In parallel with the stacking operation, the processor performs a vector fetch that reads the exception
handler start address from the vector table. When stacking is complete, the processor starts executing
the exception handler. At the same time, the processor writes an EXC_RETURN value to the LR,
indicating which stack pointer corresponds to the stack frame and what operation mode the processor
was in before the entry occurred.
If no higher-priority exception occurs during exception entry, the processor starts executing the
exception handler and automatically changes the status of the corresponding pending interrupt to
active.
If another higher-priority exception occurs during exception entry, known as late arrival, the processor
starts executing the exception handler for this exception and does not change the pending status
of the earlier exception.
2.5.7.2
Exception Return
Exception return occurs when the processor is in Handler mode and executes one of the following
instructions to load the EXC_RETURN value into the PC:
June 12, 2014
105
Texas Instruments-Production Data
The Cortex-M4F Processor
■ An LDM or POP instruction that loads the PC
■ A BX instruction using any register
■ An LDR instruction with the PC as the destination
EXC_RETURN is the value loaded into the LR on exception entry. The exception mechanism relies
on this value to detect when the processor has completed an exception handler. The lowest five
bits of this value provide information on the return stack and processor mode. Table 2-10 on page 106
shows the EXC_RETURN values with a description of the exception return behavior.
EXC_RETURN bits 31:5 are all set. When this value is loaded into the PC, it indicates to the processor
that the exception is complete, and the processor initiates the appropriate exception return sequence.
Table 2-10. Exception Return Behavior
EXC_RETURN[31:0]
Description
0xFFFF.FFE0
Reserved
0xFFFF.FFE1
Return to Handler mode.
Exception return uses floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFE2 - 0xFFFF.FFE8
Reserved
0xFFFF.FFE9
Return to Thread mode.
Exception return uses floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFEA - 0xFFFF.FFEC
Reserved
0xFFFF.FFED
Return to Thread mode.
Exception return uses floating-point state from PSP.
Execution uses PSP after return.
0xFFFF.FFEE - 0xFFFF.FFF0
Reserved
0xFFFF.FFF1
Return to Handler mode.
Exception return uses non-floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFF2 - 0xFFFF.FFF8
Reserved
0xFFFF.FFF9
Return to Thread mode.
Exception return uses non-floating-point state from MSP.
Execution uses MSP after return.
0xFFFF.FFFA - 0xFFFF.FFFC
Reserved
0xFFFF.FFFD
Return to Thread mode.
Exception return uses non-floating-point state from PSP.
Execution uses PSP after return.
0xFFFF.FFFE - 0xFFFF.FFFF
2.6
Reserved
Fault Handling
Faults are a subset of the exceptions (see “Exception Model” on page 96). The following conditions
generate a fault:
■ A bus error on an instruction fetch or vector table load or a data access.
106
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
■ An internally detected error such as an undefined instruction or an attempt to change state with
a BX instruction.
■ Attempting to execute an instruction from a memory region marked as Non-Executable (XN).
■ An MPU fault because of a privilege violation or an attempt to access an unmanaged region.
2.6.1
Fault Types
Table 2-11 on page 107 shows the types of fault, the handler used for the fault, the corresponding
fault status register, and the register bit that indicates the fault has occurred. See page 172 for more
information about the fault status registers.
Table 2-11. Faults
Fault
Handler
Fault Status Register
Bit Name
Bus error on a vector read
Hard fault
Hard Fault Status (HFAULTSTAT)
VECT
Fault escalated to a hard fault
Hard fault
Hard Fault Status (HFAULTSTAT)
FORCED
MPU or default memory mismatch on
instruction access
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
IERR
MPU or default memory mismatch on
data access
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
DERR
MPU or default memory mismatch on
exception stacking
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
MSTKE
MPU or default memory mismatch on
exception unstacking
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
MUSTKE
MPU or default memory mismatch
during lazy floating-point state
preservation
Memory management
fault
Memory Management Fault Status
(MFAULTSTAT)
MLSPERR
Bus error during exception stacking
Bus fault
Bus Fault Status (BFAULTSTAT)
BSTKE
Bus error during exception unstacking Bus fault
Bus Fault Status (BFAULTSTAT)
BUSTKE
Bus error during instruction prefetch
Bus fault
Bus Fault Status (BFAULTSTAT)
IBUS
Bus error during lazy floating-point state Bus fault
preservation
Bus Fault Status (BFAULTSTAT)
BLSPE
Precise data bus error
Bus fault
Bus Fault Status (BFAULTSTAT)
PRECISE
Imprecise data bus error
Bus fault
Bus Fault Status (BFAULTSTAT)
IMPRE
Attempt to access a coprocessor
Usage fault
Usage Fault Status (UFAULTSTAT)
NOCP
Undefined instruction
Usage fault
Usage Fault Status (UFAULTSTAT)
UNDEF
Attempt to enter an invalid instruction
b
set state
Usage fault
Usage Fault Status (UFAULTSTAT)
INVSTAT
Invalid EXC_RETURN value
Usage fault
Usage Fault Status (UFAULTSTAT)
INVPC
Illegal unaligned load or store
Usage fault
Usage Fault Status (UFAULTSTAT)
UNALIGN
Divide by 0
Usage fault
Usage Fault Status (UFAULTSTAT)
DIV0
a
a. Occurs on an access to an XN region even if the MPU is disabled.
b. Attempting to use an instruction set other than the Thumb instruction set, or returning to a non load-store-multiply instruction
with ICI continuation.
2.6.2
Fault Escalation and Hard Faults
All fault exceptions except for hard fault have configurable exception priority (see SYSPRI1 on
page 165). Software can disable execution of the handlers for these faults (see SYSHNDCTRL on
page 168).
June 12, 2014
107
Texas Instruments-Production Data
The Cortex-M4F Processor
Usually, the exception priority, together with the values of the exception mask registers, determines
whether the processor enters the fault handler, and whether a fault handler can preempt another
fault handler as described in “Exception Model” on page 96.
In some situations, a fault with configurable priority is treated as a hard fault. This process is called
priority escalation, and the fault is described as escalated to hard fault. Escalation to hard fault
occurs when:
■ A fault handler causes the same kind of fault as the one it is servicing. This escalation to hard
fault occurs because a fault handler cannot preempt itself because it must have the same priority
as the current priority level.
■ A fault handler causes a fault with the same or lower priority as the fault it is servicing. This
situation happens because the handler for the new fault cannot preempt the currently executing
fault handler.
■ An exception handler causes a fault for which the priority is the same as or lower than the currently
executing exception.
■ A fault occurs and the handler for that fault is not enabled.
If a bus fault occurs during a stack push when entering a bus fault handler, the bus fault does not
escalate to a hard fault. Thus if a corrupted stack causes a fault, the fault handler executes even
though the stack push for the handler failed. The fault handler operates but the stack contents are
corrupted.
Note:
2.6.3
Only Reset and NMI can preempt the fixed priority hard fault. A hard fault can preempt any
exception other than Reset, NMI, or another hard fault.
Fault Status Registers and Fault Address Registers
The fault status registers indicate the cause of a fault. For bus faults and memory management
faults, the fault address register indicates the address accessed by the operation that caused the
fault, as shown in Table 2-12 on page 108.
Table 2-12. Fault Status and Fault Address Registers
Handler
Status Register Name
Address Register Name
Register Description
Hard fault
Hard Fault Status (HFAULTSTAT)
-
page 178
Memory management Memory Management Fault Status
fault
(MFAULTSTAT)
Memory Management Fault
Address (MMADDR)
page 172
Bus fault
Bus Fault Address
(FAULTADDR)
page 172
-
page 172
Bus Fault Status (BFAULTSTAT)
Usage fault
2.6.4
Usage Fault Status (UFAULTSTAT)
page 179
page 180
Lockup
The processor enters a lockup state if a hard fault occurs when executing the NMI or hard fault
handlers. When the processor is in the lockup state, it does not execute any instructions. The
processor remains in lockup state until it is reset, an NMI occurs, or it is halted by a debugger.
Note:
If the lockup state occurs from the NMI handler, a subsequent NMI does not cause the
processor to leave the lockup state.
108
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
2.7
Power Management
The Cortex-M4F processor sleep modes reduce power consumption:
■ Sleep mode stops the processor clock.
■ Deep-sleep mode stops the system clock and switches off the PLL and Flash memory.
The SLEEPDEEP bit of the System Control (SYSCTRL) register selects which sleep mode is used
(see page 161). For more information about the behavior of the sleep modes, see “System
Control” on page 221.
This section describes the mechanisms for entering sleep mode and the conditions for waking up
from sleep mode, both of which apply to Sleep mode and Deep-sleep mode.
2.7.1
Entering Sleep Modes
This section describes the mechanisms software can use to put the processor into one of the sleep
modes.
The system can generate spurious wake-up events, for example a debug operation wakes up the
processor. Therefore, software must be able to put the processor back into sleep mode after such
an event. A program might have an idle loop to put the processor back to sleep mode.
2.7.1.1
Wait for Interrupt
The wait for interrupt instruction, WFI, causes immediate entry to sleep mode unless the wake-up
condition is true (see “Wake Up from WFI or Sleep-on-Exit” on page 110). When the processor
executes a WFI instruction, it stops executing instructions and enters sleep mode. See the
Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide (literature
number ARM DUI 0553A) for more information.
2.7.1.2
Wait for Event
The wait for event instruction, WFE, causes entry to sleep mode conditional on the value of a one-bit
event register. When the processor executes a WFE instruction, it checks the event register. If the
register is 0, the processor stops executing instructions and enters sleep mode. If the register is 1,
the processor clears the register and continues executing instructions without entering sleep mode.
If the event register is 1, the processor must not enter sleep mode on execution of a WFE instruction.
Typically, this situation occurs if an SEV instruction has been executed. Software cannot access
this register directly.
See the Cortex™-M4 instruction set chapter in the ARM® Cortex™-M4 Devices Generic User Guide
(literature number ARM DUI 0553A) for more information.
2.7.1.3
Sleep-on-Exit
If the SLEEPEXIT bit of the SYSCTRL register is set, when the processor completes the execution
of all exception handlers, it returns to Thread mode and immediately enters sleep mode. This
mechanism can be used in applications that only require the processor to run when an exception
occurs.
2.7.2
Wake Up from Sleep Mode
The conditions for the processor to wake up depend on the mechanism that caused it to enter sleep
mode.
June 12, 2014
109
Texas Instruments-Production Data
The Cortex-M4F Processor
2.7.2.1
Wake Up from WFI or Sleep-on-Exit
Normally, the processor wakes up only when the NVIC detects an exception with sufficient priority
to cause exception entry. Some embedded systems might have to execute system restore tasks
after the processor wakes up and before executing an interrupt handler. Entry to the interrupt handler
can be delayed by setting the PRIMASK bit and clearing the FAULTMASK bit. If an interrupt arrives
that is enabled and has a higher priority than current exception priority, the processor wakes up but
does not execute the interrupt handler until the processor clears PRIMASK. For more information
about PRIMASK and FAULTMASK, see page 80 and page 81.
2.7.2.2
Wake Up from WFE
The processor wakes up if it detects an exception with sufficient priority to cause exception entry.
In addition, if the SEVONPEND bit in the SYSCTRL register is set, any new pending interrupt triggers
an event and wakes up the processor, even if the interrupt is disabled or has insufficient priority to
cause exception entry. For more information about SYSCTRL, see page 161.
2.8
Instruction Set Summary
The processor implements a version of the Thumb instruction set. Table 2-13 on page 110 lists the
supported instructions.
Note:
In Table 2-13 on page 110:
■
■
■
■
■
Angle brackets, <>, enclose alternative forms of the operand
Braces, {}, enclose optional operands
The Operands column is not exhaustive
Op2 is a flexible second operand that can be either a register or a constant
Most instructions can use an optional condition code suffix
For more information on the instructions and operands, see the instruction descriptions in
the ARM® Cortex™-M4 Technical Reference Manual.
Table 2-13. Cortex-M4F Instruction Summary
Mnemonic
Operands
Brief Description
Flags
ADC, ADCS
{Rd,} Rn, Op2
Add with carry
N,Z,C,V
ADD, ADDS
{Rd,} Rn, Op2
Add
N,Z,C,V
ADD, ADDW
{Rd,} Rn , #imm12
Add
-
ADR
Rd, label
Load PC-relative address
-
AND, ANDS
{Rd,} Rn, Op2
Logical AND
N,Z,C
ASR, ASRS
Rd, Rm, <Rs|#n>
Arithmetic shift right
N,Z,C
B
label
Branch
-
BFC
Rd, #lsb, #width
Bit field clear
-
BFI
Rd, Rn, #lsb, #width
Bit field insert
-
BIC, BICS
{Rd,} Rn, Op2
Bit clear
N,Z,C
BKPT
#imm
Breakpoint
-
BL
label
Branch with link
-
BLX
Rm
Branch indirect with link
-
BX
Rm
Branch indirect
-
CBNZ
Rn, label
Compare and branch if non-zero
-
110
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
CBZ
Rn, label
Compare and branch if zero
-
CLREX
-
Clear exclusive
-
CLZ
Rd, Rm
Count leading zeros
-
CMN
Rn, Op2
Compare negative
N,Z,C,V
CMP
Rn, Op2
Compare
N,Z,C,V
CPSID
i
Change processor state, disable
interrupts
-
CPSIE
i
Change processor state, enable
interrupts
-
DMB
-
Data memory barrier
-
DSB
-
Data synchronization barrier
-
EOR, EORS
{Rd,} Rn, Op2
Exclusive OR
N,Z,C
ISB
-
Instruction synchronization barrier
-
IT
-
If-Then condition block
-
LDM
Rn{!}, reglist
Load multiple registers, increment after -
LDMDB, LDMEA
Rn{!}, reglist
Load multiple registers, decrement
before
LDMFD, LDMIA
Rn{!}, reglist
Load multiple registers, increment after -
LDR
Rt, [Rn, #offset]
Load register with word
-
LDRB, LDRBT
Rt, [Rn, #offset]
Load register with byte
-
LDRD
Rt, Rt2, [Rn, #offset]
Load register with two bytes
-
LDREX
Rt, [Rn, #offset]
Load register exclusive
-
LDREXB
Rt, [Rn]
Load register exclusive with byte
-
LDREXH
Rt, [Rn]
Load register exclusive with halfword
-
LDRH, LDRHT
Rt, [Rn, #offset]
Load register with halfword
-
LDRSB, LDRSBT
Rt, [Rn, #offset]
Load register with signed byte
-
LDRSH, LDRSHT
Rt, [Rn, #offset]
Load register with signed halfword
-
LDRT
Rt, [Rn, #offset]
Load register with word
-
LSL, LSLS
Rd, Rm, <Rs|#n>
Logical shift left
N,Z,C
LSR, LSRS
Rd, Rm, <Rs|#n>
Logical shift right
N,Z,C
MLA
Rd, Rn, Rm, Ra
Multiply with accumulate, 32-bit result
-
MLS
Rd, Rn, Rm, Ra
Multiply and subtract, 32-bit result
-
MOV, MOVS
Rd, Op2
Move
N,Z,C
MOV, MOVW
Rd, #imm16
Move 16-bit constant
N,Z,C
MOVT
Rd, #imm16
Move top
-
MRS
Rd, spec_reg
Move from special register to general
register
-
MSR
spec_reg, Rm
Move from general register to special
register
N,Z,C,V
MUL, MULS
{Rd,} Rn, Rm
Multiply, 32-bit result
N,Z
MVN, MVNS
Rd, Op2
Move NOT
N,Z,C
NOP
-
No operation
-
ORN, ORNS
{Rd,} Rn, Op2
Logical OR NOT
N,Z,C
June 12, 2014
-
111
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
ORR, ORRS
{Rd,} Rn, Op2
Logical OR
N,Z,C
PKHTB, PKHBT
{Rd,} Rn, Rm, Op2
Pack halfword
-
POP
reglist
Pop registers from stack
-
PUSH
reglist
Push registers onto stack
-
QADD
{Rd,} Rn, Rm
Saturating add
Q
QADD16
{Rd,} Rn, Rm
Saturating add 16
-
QADD8
{Rd,} Rn, Rm
Saturating add 8
-
QASX
{Rd,} Rn, Rm
Saturating add and subtract with
exchange
-
QDADD
{Rd,} Rn, Rm
Saturating double and add
Q
QDSUB
{Rd,} Rn, Rm
Saturating double and subtract
Q
QSAX
{Rd,} Rn, Rm
Saturating subtract and add with
exchange
-
QSUB
{Rd,} Rn, Rm
Saturating subtract
Q
QSUB16
{Rd,} Rn, Rm
Saturating subtract 16
-
QSUB8
{Rd,} Rn, Rm
Saturating subtract 8
-
RBIT
Rd, Rn
Reverse bits
-
REV
Rd, Rn
Reverse byte order in a word
-
REV16
Rd, Rn
Reverse byte order in each halfword
-
REVSH
Rd, Rn
Reverse byte order in bottom halfword
and sign extend
-
ROR, RORS
Rd, Rm, <Rs|#n>
Rotate right
N,Z,C
RRX, RRXS
Rd, Rm
Rotate right with extend
N,Z,C
RSB, RSBS
{Rd,} Rn, Op2
Reverse subtract
N,Z,C,V
SADD16
{Rd,} Rn, Rm
Signed add 16
GE
SADD8
{Rd,} Rn, Rm
Signed add 8
GE
SASX
{Rd,} Rn, Rm
Signed add and subtract with exchange GE
SBC, SBCS
{Rd,} Rn, Op2
Subtract with carry
N,Z,C,V
SBFX
Rd, Rn, #lsb, #width
Signed bit field extract
-
SDIV
{Rd,} Rn, Rm
Signed divide
-
SEL
{Rd,} Rn, Rm
Select bytes
-
SEV
-
Send event
-
SHADD16
{Rd,} Rn, Rm
Signed halving add 16
-
SHADD8
{Rd,} Rn, Rm
Signed halving add 8
-
SHASX
{Rd,} Rn, Rm
Signed halving add and subtract with
exchange
-
SHSAX
{Rd,} Rn, Rm
Signed halving add and subtract with
exchange
-
SHSUB16
{Rd,} Rn, Rm
Signed halving subtract 16
-
SHSUB8
{Rd,} Rn, Rm
Signed halving subtract 8
-
112
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
SMLABB,
Rd, Rn, Rm, Ra
Signed multiply accumulate long
(halfwords)
Q
Rd, Rn, Rm, Ra
Signed multiply accumulate dual
Q
SMLAL
RdLo, RdHi, Rn, Rm
Signed multiply with accumulate
(32x32+64), 64-bit result
-
SMLALBB,
RdLo, RdHi, Rn, Rm
Signed multiply accumulate long
(halfwords)
-
SMLALD, SMLALDX
RdLo, RdHi, Rn, Rm
Signed multiply accumulate long dual
-
SMLAWB,SMLAWT
Rd, Rn, Rm, Ra
Signed multiply accumulate, word by
halfword
Q
SMLSD
Rd, Rn, Rm, Ra
Signed multiply subtract dual
Q
RdLo, RdHi, Rn, Rm
Signed multiply subtract long dual
SMMLA
Rd, Rn, Rm, Ra
Signed most significant word multiply
accumulate
-
SMMLS,
Rd, Rn, Rm, Ra
Signed most significant word multiply
subtract
-
{Rd,} Rn, Rm
Signed most significant word multiply
-
{Rd,} Rn, Rm
Signed dual multiply add
Q
{Rd,} Rn, Rm
Signed multiply halfwords
-
SMULL
RdLo, RdHi, Rn, Rm
Signed multiply (32x32), 64-bit result
-
SMULWB,
{Rd,} Rn, Rm
Signed multiply by halfword
-
{Rd,} Rn, Rm
Signed dual multiply subtract
-
SSAT
Rd, #n, Rm {,shift #s}
Signed saturate
Q
SSAT16
Rd, #n, Rm
Signed saturate 16
Q
SSAX
{Rd,} Rn, Rm
Saturating subtract and add with
exchange
GE
SSUB16
{Rd,} Rn, Rm
Signed subtract 16
-
SSUB8
{Rd,} Rn, Rm
Signed subtract 8
-
STM
Rn{!}, reglist
Store multiple registers, increment after -
SMLABT,
SMLATB,
SMLATT
SMLAD,
SMLADX
SMLALBT,
SMLALTB,
SMLALTT
SMLSDX
SMLSLD
SMLSLDX
SMMLR
SMMUL,
SMMULR
SMUAD
SMUADX
SMULBB,
SMULBT,
SMULTB,
SMULTT
SMULWT
SMUSD,
SMUSDX
June 12, 2014
113
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
STMDB, STMEA
Rn{!}, reglist
Store multiple registers, decrement
before
-
STMFD, STMIA
Rn{!}, reglist
Store multiple registers, increment after -
STR
Rt, [Rn {, #offset}]
Store register word
-
STRB, STRBT
Rt, [Rn {, #offset}]
Store register byte
-
STRD
Rt, Rt2, [Rn {, #offset}]
Store register two words
-
STREX
Rt, Rt, [Rn {, #offset}]
Store register exclusive
-
STREXB
Rd, Rt, [Rn]
Store register exclusive byte
-
STREXH
Rd, Rt, [Rn]
Store register exclusive halfword
-
STRH, STRHT
Rt, [Rn {, #offset}]
Store register halfword
-
STRSB, STRSBT
Rt, [Rn {, #offset}]
Store register signed byte
-
STRSH, STRSHT
Rt, [Rn {, #offset}]
Store register signed halfword
-
STRT
Rt, [Rn {, #offset}]
Store register word
-
SUB, SUBS
{Rd,} Rn, Op2
Subtract
N,Z,C,V
SUB, SUBW
{Rd,} Rn, #imm12
Subtract 12-bit constant
N,Z,C,V
SVC
#imm
Supervisor call
-
SXTAB
{Rd,} Rn, Rm, {,ROR #}
Extend 8 bits to 32 and add
-
SXTAB16
{Rd,} Rn, Rm,{,ROR #}
Dual extend 8 bits to 16 and add
-
SXTAH
{Rd,} Rn, Rm,{,ROR #}
Extend 16 bits to 32 and add
-
SXTB16
{Rd,} Rm {,ROR #n}
Signed extend byte 16
-
SXTB
{Rd,} Rm {,ROR #n}
Sign extend a byte
-
SXTH
{Rd,} Rm {,ROR #n}
Sign extend a halfword
-
TBB
[Rn, Rm]
Table branch byte
-
TBH
[Rn, Rm, LSL #1]
Table branch halfword
-
TEQ
Rn, Op2
Test equivalence
N,Z,C
TST
Rn, Op2
Test
N,Z,C
UADD16
{Rd,} Rn, Rm
Unsigned add 16
GE
UADD8
{Rd,} Rn, Rm
Unsigned add 8
GE
UASX
{Rd,} Rn, Rm
Unsigned add and subtract with
exchange
GE
UHADD16
{Rd,} Rn, Rm
Unsigned halving add 16
-
UHADD8
{Rd,} Rn, Rm
Unsigned halving add 8
-
UHASX
{Rd,} Rn, Rm
Unsigned halving add and subtract with exchange
UHSAX
{Rd,} Rn, Rm
Unsigned halving subtract and add with exchange
UHSUB16
{Rd,} Rn, Rm
Unsigned halving subtract 16
-
UHSUB8
{Rd,} Rn, Rm
Unsigned halving subtract 8
-
UBFX
Rd, Rn, #lsb, #width
Unsigned bit field extract
-
UDIV
{Rd,} Rn, Rm
Unsigned divide
-
UMAAL
RdLo, RdHi, Rn, Rm
Unsigned multiply accumulate
accumulate long (32x32+64), 64-bit
result
-
114
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
UMLAL
RdLo, RdHi, Rn, Rm
Unsigned multiply with accumulate
(32x32+32+32), 64-bit result
-
UMULL
RdLo, RdHi, Rn, Rm
Unsigned multiply (32x 2), 64-bit result -
UQADD16
{Rd,} Rn, Rm
Unsigned Saturating Add 16
-
UQADD8
{Rd,} Rn, Rm
Unsigned Saturating Add 8
-
UQASX
{Rd,} Rn, Rm
Unsigned Saturating Add and Subtract with Exchange
UQSAX
{Rd,} Rn, Rm
Unsigned Saturating Subtract and Add with Exchange
UQSUB16
{Rd,} Rn, Rm
Unsigned Saturating Subtract 16
-
UQSUB8
{Rd,} Rn, Rm
Unsigned Saturating Subtract 8
-
USAD8
{Rd,} Rn, Rm
Unsigned Sum of Absolute Differences -
USADA8
{Rd,} Rn, Rm, Ra
Unsigned Sum of Absolute Differences and Accumulate
USAT
Rd, #n, Rm {,shift #s}
Unsigned Saturate
Q
USAT16
Rd, #n, Rm
Unsigned Saturate 16
Q
USAX
{Rd,} Rn, Rm
Unsigned Subtract and add with
Exchange
GE
USUB16
{Rd,} Rn, Rm
Unsigned Subtract 16
GE
USUB8
{Rd,} Rn, Rm
Unsigned Subtract 8
GE
UXTAB
{Rd,} Rn, Rm, {,ROR #}
Rotate, extend 8 bits to 32 and Add
-
UXTAB16
{Rd,} Rn, Rm, {,ROR #}
Rotate, dual extend 8 bits to 16 and Add -
UXTAH
{Rd,} Rn, Rm, {,ROR #}
Rotate, unsigned extend and Add
Halfword
-
UXTB
{Rd,} Rm, {,ROR #n}
Zero extend a Byte
-
UXTB16
{Rd,} Rm, {,ROR #n}
Unsigned Extend Byte 16
-
UXTH
{Rd,} Rm, {,ROR #n}
Zero extend a Halfword
-
VABS.F32
Sd, Sm
Floating-point Absolute
-
VADD.F32
{Sd,} Sn, Sm
Floating-point Add
-
VCMP.F32
Sd, <Sm | #0.0>
Compare two floating-point registers, or FPSCR
one floating-point register and zero
VCMPE.F32
Sd, <Sm | #0.0>
Compare two floating-point registers, or FPSCR
one floating-point register and zero with
Invalid Operation check
VCVT.S32.F32
Sd, Sm
Convert between floating-point and
integer
VCVT.S16.F32
Sd, Sd, #fbits
Convert between floating-point and fixed point
VCVTR.S32.F32
Sd, Sm
Convert between floating-point and
integer with rounding
-
VCVT<B|H>.F32.F16
Sd, Sm
Converts half-precision value to
single-precision
-
VCVTT<B|T>.F32.F16
Sd, Sm
Converts single-precision register to
half-precision
-
VDIV.F32
{Sd,} Sn, Sm
Floating-point Divide
-
VFMA.F32
{Sd,} Sn, Sm
Floating-point Fused Multiply Accumulate -
June 12, 2014
-
115
Texas Instruments-Production Data
The Cortex-M4F Processor
Table 2-13. Cortex-M4F Instruction Summary (continued)
Mnemonic
Operands
Brief Description
Flags
VFNMA.F32
{Sd,} Sn, Sm
Floating-point Fused Negate Multiply
Accumulate
-
VFMS.F32
{Sd,} Sn, Sm
Floating-point Fused Multiply Subtract
-
VFNMS.F32
{Sd,} Sn, Sm
Floating-point Fused Negate Multiply
Subtract
-
VLDM.F<32|64>
Rn{!}, list
Load Multiple extension registers
-
VLDR.F<32|64>
<Dd|Sd>, [Rn]
Load an extension register from memory -
VLMA.F32
{Sd,} Sn, Sm
Floating-point Multiply Accumulate
-
VLMS.F32
{Sd,} Sn, Sm
Floating-point Multiply Subtract
-
VMOV.F32
Sd, #imm
Floating-point Move immediate
-
VMOV
Sd, Sm
Floating-point Move register
-
VMOV
Sn, Rt
Copy ARM core register to single
precision
-
VMOV
Sm, Sm1, Rt, Rt2
Copy 2 ARM core registers to 2 single
precision
-
VMOV
Dd[x], Rt
Copy ARM core register to scalar
-
VMOV
Rt, Dn[x]
Copy scalar to ARM core register
-
VMRS
Rt, FPSCR
Move FPSCR to ARM core register or
APSR
N,Z,C,V
VMSR
FPSCR, Rt
Move to FPSCR from ARM Core register FPSCR
VMUL.F32
{Sd,} Sn, Sm
Floating-point Multiply
-
VNEG.F32
Sd, Sm
Floating-point Negate
-
VNMLA.F32
{Sd,} Sn, Sm
Floating-point Multiply and Add
-
VNMLS.F32
{Sd,} Sn, Sm
Floating-point Multiply and Subtract
-
VNMUL
{Sd,} Sn, Sm
Floating-point Multiply
-
VPOP
list
Pop extension registers
-
VPUSH
list
Push extension registers
-
VSQRT.F32
Sd, Sm
Calculates floating-point Square Root
-
VSTM
Rn{!}, list
Floating-point register Store Multiple
-
VSTR.F3<32|64>
Sd, [Rn]
Stores an extension register to memory -
VSUB.F<32|64>
{Sd,} Sn, Sm
Floating-point Subtract
-
WFE
-
Wait for event
-
WFI
-
Wait for interrupt
-
116
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
3
Cortex-M4 Peripherals
This chapter provides information on the Tiva™ C Series implementation of the Cortex-M4 processor
peripherals, including:
■ SysTick (see page 118)
Provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible
control mechanism.
■ Nested Vectored Interrupt Controller (NVIC) (see page 119)
– Facilitates low-latency exception and interrupt handling
– Controls power management
– Implements system control registers
■ System Control Block (SCB) (see page 120)
Provides system implementation information and system control, including configuration, control,
and reporting of system exceptions.
■ Memory Protection Unit (MPU) (see page 120)
Supports the standard ARMv7 Protected Memory System Architecture (PMSA) model. The MPU
provides full support for protection regions, overlapping protection regions, access permissions,
and exporting memory attributes to the system.
■ Floating-Point Unit (FPU) (see page 125)
Fully supports single-precision add, subtract, multiply, divide, multiply and accumulate, and
square root operations. It also provides conversions between fixed-point and floating-point data
formats, and floating-point constant instructions.
Table 3-1 on page 117 shows the address map of the Private Peripheral Bus (PPB). Some peripheral
register regions are split into two address regions, as indicated by two addresses listed.
Table 3-1. Core Peripheral Register Regions
Address
Core Peripheral
Description (see page ...)
0xE000.E010-0xE000.E01F
System Timer
118
0xE000.E100-0xE000.E4EF
Nested Vectored Interrupt Controller
119
System Control Block
120
0xE000.ED90-0xE000.EDB8
Memory Protection Unit
120
0xE000.EF30-0xE000.EF44
Floating Point Unit
125
0xE000.EF00-0xE000.EF03
0xE000.E008-0xE000.E00F
0xE000.ED00-0xE000.ED3F
3.1
Functional Description
This chapter provides information on the Tiva™ C Series implementation of the Cortex-M4 processor
peripherals: SysTick, NVIC, SCB, MPU, FPU.
June 12, 2014
117
Texas Instruments-Production Data
Cortex-M4 Peripherals
3.1.1
System Timer (SysTick)
Cortex-M4 includes an integrated system timer, SysTick, which provides a simple, 24-bit
clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter
can be used in several different ways, for example as:
■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick
routine.
■ A high-speed alarm timer using the system clock.
■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock
used and the dynamic range of the counter.
■ A simple counter used to measure time to completion and time used.
■ An internal clock source control based on missing/meeting durations. The COUNT bit in the
STCTRL control and status register can be used to determine if an action completed within a
set duration, as part of a dynamic clock management control loop.
The timer consists of three registers:
■ SysTick Control and Status (STCTRL): A control and status counter to configure its clock,
enable the counter, enable the SysTick interrupt, and determine counter status.
■ SysTick Reload Value (STRELOAD): The reload value for the counter, used to provide the
counter's wrap value.
■ SysTick Current Value (STCURRENT): The current value of the counter.
When enabled, the timer counts down on each clock from the reload value to zero, reloads (wraps)
to the value in the STRELOAD register on the next clock edge, then decrements on subsequent
clocks. Clearing the STRELOAD register disables the counter on the next wrap. When the counter
reaches zero, the COUNT status bit is set. The COUNT bit clears on reads.
Writing to the STCURRENT register clears the register and the COUNT status bit. The write does
not trigger the SysTick exception logic. On a read, the current value is the value of the register at
the time the register is accessed.
The SysTick counter runs on either the system clock or the precision internal oscillator (PIOSC)
divided by 4. If this clock signal is stopped for low power mode, the SysTick counter stops. SysTick
can be kept running during Deep-sleep mode by setting the CLK_SRC bit in the SysTick Control
and Status Register (STCTRL) register and ensuring that the PIOSCPD bit in the Deep Sleep
Clock Configuration (DSLPCLKCFG) register is clear. Ensure software uses aligned word accesses
to access the SysTick registers.
The SysTick counter reload and current value are undefined at reset; the correct initialization
sequence for the SysTick counter is:
1. Program the value in the STRELOAD register.
2. Clear the STCURRENT register by writing to it with any value.
3. Configure the STCTRL register for the required operation.
Note:
When the processor is halted for debugging, the counter does not decrement.
118
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
3.1.2
Nested Vectored Interrupt Controller (NVIC)
This section describes the Nested Vectored Interrupt Controller (NVIC) and the registers it uses.
The NVIC supports:
■ 77 interrupts.
■ A programmable priority level of 0-7 for each interrupt. A higher level corresponds to a lower
priority, so level 0 is the highest interrupt priority.
■ Low-latency exception and interrupt handling.
■ Level and pulse detection of interrupt signals.
■ Dynamic reprioritization of interrupts.
■ Grouping of priority values into group priority and subpriority fields.
■ Interrupt tail-chaining.
■ An external Non-maskable interrupt (NMI).
The processor automatically stacks its state on exception entry and unstacks this state on exception
exit, with no instruction overhead, providing low latency exception handling.
3.1.2.1
Level-Sensitive and Pulse Interrupts
The processor supports both level-sensitive and pulse interrupts. Pulse interrupts are also described
as edge-triggered interrupts.
A level-sensitive interrupt is held asserted until the peripheral deasserts the interrupt signal. Typically
this happens because the ISR accesses the peripheral, causing it to clear the interrupt request. A
pulse interrupt is an interrupt signal sampled synchronously on the rising edge of the processor
clock. To ensure the NVIC detects the interrupt, the peripheral must assert the interrupt signal for
at least one clock cycle, during which the NVIC detects the pulse and latches the interrupt.
When the processor enters the ISR, it automatically removes the pending state from the interrupt
(see “Hardware and Software Control of Interrupts” on page 119 for more information). For a
level-sensitive interrupt, if the signal is not deasserted before the processor returns from the ISR,
the interrupt becomes pending again, and the processor must execute its ISR again. As a result,
the peripheral can hold the interrupt signal asserted until it no longer needs servicing.
3.1.2.2
Hardware and Software Control of Interrupts
The Cortex-M4 latches all interrupts. A peripheral interrupt becomes pending for one of the following
reasons:
■ The NVIC detects that the interrupt signal is High and the interrupt is not active.
■ The NVIC detects a rising edge on the interrupt signal.
■ Software writes to the corresponding interrupt set-pending register bit, or to the Software Trigger
Interrupt (SWTRIG) register to make a Software-Generated Interrupt pending. See the INT bit
in the PEND0 register on page 141 or SWTRIG on page 151.
A pending interrupt remains pending until one of the following:
June 12, 2014
119
Texas Instruments-Production Data
Cortex-M4 Peripherals
■ The processor enters the ISR for the interrupt, changing the state of the interrupt from pending
to active. Then:
– For a level-sensitive interrupt, when the processor returns from the ISR, the NVIC samples
the interrupt signal. If the signal is asserted, the state of the interrupt changes to pending,
which might cause the processor to immediately re-enter the ISR. Otherwise, the state of the
interrupt changes to inactive.
– For a pulse interrupt, the NVIC continues to monitor the interrupt signal, and if this is pulsed
the state of the interrupt changes to pending and active. In this case, when the processor
returns from the ISR the state of the interrupt changes to pending, which might cause the
processor to immediately re-enter the ISR.
If the interrupt signal is not pulsed while the processor is in the ISR, when the processor
returns from the ISR the state of the interrupt changes to inactive.
■ Software writes to the corresponding interrupt clear-pending register bit
– For a level-sensitive interrupt, if the interrupt signal is still asserted, the state of the interrupt
does not change. Otherwise, the state of the interrupt changes to inactive.
– For a pulse interrupt, the state of the interrupt changes to inactive, if the state was pending
or to active, if the state was active and pending.
3.1.3
System Control Block (SCB)
The System Control Block (SCB) provides system implementation information and system control,
including configuration, control, and reporting of the system exceptions.
3.1.4
Memory Protection Unit (MPU)
This section describes the Memory protection unit (MPU). The MPU divides the memory map into
a number of regions and defines the location, size, access permissions, and memory attributes of
each region. The MPU supports independent attribute settings for each region, overlapping regions,
and export of memory attributes to the system.
The memory attributes affect the behavior of memory accesses to the region. The Cortex-M4 MPU
defines eight separate memory regions, 0-7, and a background region.
When memory regions overlap, a memory access is affected by the attributes of the region with the
highest number. For example, the attributes for region 7 take precedence over the attributes of any
region that overlaps region 7.
The background region has the same memory access attributes as the default memory map, but is
accessible from privileged software only.
The Cortex-M4 MPU memory map is unified, meaning that instruction accesses and data accesses
have the same region settings.
If a program accesses a memory location that is prohibited by the MPU, the processor generates
a memory management fault, causing a fault exception and possibly causing termination of the
process in an OS environment. In an OS environment, the kernel can update the MPU region setting
dynamically based on the process to be executed. Typically, an embedded OS uses the MPU for
memory protection.
Configuration of MPU regions is based on memory types (see “Memory Regions, Types and
Attributes” on page 90 for more information).
120
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 3-2 on page 121 shows the possible MPU region attributes. See the section called “MPU
Configuration for a Tiva™ C Series Microcontroller” on page 125 for guidelines for programming a
microcontroller implementation.
Table 3-2. Memory Attributes Summary
Memory Type
Description
Strongly Ordered
All accesses to Strongly Ordered memory occur in program order.
Device
Memory-mapped peripherals
Normal
Normal memory
To avoid unexpected behavior, disable the interrupts before updating the attributes of a region that
the interrupt handlers might access.
Ensure software uses aligned accesses of the correct size to access MPU registers:
■ Except for the MPU Region Attribute and Size (MPUATTR) register, all MPU registers must
be accessed with aligned word accesses.
■ The MPUATTR register can be accessed with byte or aligned halfword or word accesses.
The processor does not support unaligned accesses to MPU registers.
When setting up the MPU, and if the MPU has previously been programmed, disable unused regions
to prevent any previous region settings from affecting the new MPU setup.
3.1.4.1
Updating an MPU Region
To update the attributes for an MPU region, the MPU Region Number (MPUNUMBER), MPU
Region Base Address (MPUBASE) and MPUATTR registers must be updated. Each register can
be programmed separately or with a multiple-word write to program all of these registers. You can
use the MPUBASEx and MPUATTRx aliases to program up to four regions simultaneously using
an STM instruction.
Updating an MPU Region Using Separate Words
This example simple code configures one region:
; R1 = region number
; R2 = size/enable
; R3 = attributes
; R4 = address
LDR R0,=MPUNUMBER
STR R1, [R0, #0x0]
STR R4, [R0, #0x4]
STRH R2, [R0, #0x8]
STRH R3, [R0, #0xA]
;
;
;
;
;
0xE000ED98, MPU region number register
Region Number
Region Base Address
Region Size and Enable
Region Attribute
Disable a region before writing new region settings to the MPU if you have previously enabled the
region being changed. For example:
; R1 = region number
; R2 = size/enable
; R3 = attributes
; R4 = address
LDR R0,=MPUNUMBER
; 0xE000ED98, MPU region number register
June 12, 2014
121
Texas Instruments-Production Data
Cortex-M4 Peripherals
STR R1, [R0, #0x0]
BIC R2, R2, #1
STRH R2, [R0, #0x8]
STR R4, [R0, #0x4]
STRH R3, [R0, #0xA]
ORR R2, #1
STRH R2, [R0, #0x8]
;
;
;
;
;
;
;
Region Number
Disable
Region Size and Enable
Region Base Address
Region Attribute
Enable
Region Size and Enable
Software must use memory barrier instructions:
■ Before MPU setup, if there might be outstanding memory transfers, such as buffered writes, that
might be affected by the change in MPU settings.
■ After MPU setup, if it includes memory transfers that must use the new MPU settings.
However, memory barrier instructions are not required if the MPU setup process starts by entering
an exception handler, or is followed by an exception return, because the exception entry and
exception return mechanism cause memory barrier behavior.
Software does not need any memory barrier instructions during MPU setup, because it accesses
the MPU through the Private Peripheral Bus (PPB), which is a Strongly Ordered memory region.
For example, if all of the memory access behavior is intended to take effect immediately after the
programming sequence, then a DSB instruction and an ISB instruction should be used. A DSB is
required after changing MPU settings, such as at the end of context switch. An ISB is required if
the code that programs the MPU region or regions is entered using a branch or call. If the
programming sequence is entered using a return from exception, or by taking an exception, then
an ISB is not required.
Updating an MPU Region Using Multi-Word Writes
The MPU can be programmed directly using multi-word writes, depending how the information is
divided. Consider the following reprogramming:
; R1 = region number
; R2 = address
; R3 = size, attributes in one
LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register
STR R1, [R0, #0x0] ; Region Number
STR R2, [R0, #0x4] ; Region Base Address
STR R3, [R0, #0x8] ; Region Attribute, Size and Enable
An STM instruction can be used to optimize this:
; R1 = region number
; R2 = address
; R3 = size, attributes in one
LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register
STM R0, {R1-R3}
; Region number, address, attribute, size and enable
This operation can be done in two words for prepacked information, meaning that the MPU Region
Base Address (MPUBASE) register (see page 185) contains the required region number and has
the VALID bit set. This method can be used when the data is statically packed, for example in a
boot loader:
122
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
; R1 = address and region number in one
; R2 = size and attributes in one
LDR R0, =MPUBASE
; 0xE000ED9C, MPU Region Base register
STR R1, [R0, #0x0] ; Region base address and region number combined
; with VALID (bit 4) set
STR R2, [R0, #0x4] ; Region Attribute, Size and Enable
Subregions
Regions of 256 bytes or more are divided into eight equal-sized subregions. Set the corresponding
bit in the SRD field of the MPU Region Attribute and Size (MPUATTR) register (see page 187) to
disable a subregion. The least-significant bit of the SRD field controls the first subregion, and the
most-significant bit controls the last subregion. Disabling a subregion means another region
overlapping the disabled range matches instead. If no other enabled region overlaps the disabled
subregion, the MPU issues a fault.
Regions of 32, 64, and 128 bytes do not support subregions. With regions of these sizes, the SRD
field must be configured to 0x00, otherwise the MPU behavior is unpredictable.
Example of SRD Use
Two regions with the same base address overlap. Region one is 128 KB, and region two is 512 KB.
To ensure the attributes from region one apply to the first 128 KB region, configure the SRD field for
region two to 0x03 to disable the first two subregions, as Figure 3-1 on page 123 shows.
Figure 3-1. SRD Use Example
Region 2, with
subregions
Region 1
Base address of both regions
3.1.4.2
Offset from
base address
512KB
448KB
384KB
320KB
256KB
192KB
128KB
Disabled subregion
64KB
Disabled subregion
0
MPU Access Permission Attributes
The access permission bits, TEX, S, C, B, AP, and XN of the MPUATTR register, control access to
the corresponding memory region. If an access is made to an area of memory without the required
permissions, then the MPU generates a permission fault.
Table 3-3 on page 123 shows the encodings for the TEX, C, B, and S access permission bits. All
encodings are shown for completeness, however the current implementation of the Cortex-M4 does
not support the concept of cacheability or shareability. Refer to the section called “MPU Configuration
for a Tiva™ C Series Microcontroller” on page 125 for information on programming the MPU for
TM4C123BE6PM implementations.
Table 3-3. TEX, S, C, and B Bit Field Encoding
TEX
S
000b
x
000
B
Memory Type
Shareability
Other Attributes
0
0
Strongly Ordered
Shareable
-
a
0
1
Device
Shareable
-
x
C
a
June 12, 2014
123
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-3. TEX, S, C, and B Bit Field Encoding (continued)
TEX
S
C
B
Memory Type
Shareability
000
0
1
0
Normal
Not shareable
000
1
1
0
Normal
Shareable
000
0
1
1
Normal
Not shareable
000
1
1
1
Normal
Shareable
Other Attributes
Outer and inner
write-through. No write
allocate.
001
0
0
0
Normal
Not shareable
001
1
0
0
Normal
Shareable
Outer and inner
non-cacheable.
001
x
a
0
1
Reserved encoding
-
-
a
001
x
1
0
Reserved encoding
-
-
001
0
1
1
Normal
Not shareable
001
1
1
1
Normal
Shareable
Outer and inner
write-back. Write and
read allocate.
010
x
a
0
0
Device
Not shareable
Nonshared Device.
a
a
010
x
0
1
Reserved encoding
-
-
010
x
1
x
Reserved encoding
-
-
1BB
0
A
A
Normal
Not shareable
1BB
1
A
A
Normal
Shareable
Cached memory (BB =
outer policy, AA = inner
policy).
a
See Table 3-4 for the
encoding of the AA and
BB bits.
a. The MPU ignores the value of this bit.
Table 3-4 on page 124 shows the cache policy for memory attribute encodings with a TEX value in
the range of 0x4-0x7.
Table 3-4. Cache Policy for Memory Attribute Encoding
Encoding, AA or BB
Corresponding Cache Policy
00
Non-cacheable
01
Write back, write and read allocate
10
Write through, no write allocate
11
Write back, no write allocate
Table 3-5 on page 124 shows the AP encodings in the MPUATTR register that define the access
permissions for privileged and unprivileged software.
Table 3-5. AP Bit Field Encoding
AP Bit Field
Privileged
Permissions
Unprivileged
Permissions
Description
000
No access
No access
All accesses generate a permission fault.
001
RW
No access
Access from privileged software only.
010
RW
RO
Writes by unprivileged software generate a
permission fault.
011
RW
RW
Full access.
100
Unpredictable
Unpredictable
Reserved.
101
RO
No access
Reads by privileged software only.
124
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 3-5. AP Bit Field Encoding (continued)
AP Bit Field
Privileged
Permissions
Unprivileged
Permissions
Description
110
RO
RO
Read-only, by privileged or unprivileged software.
111
RO
RO
Read-only, by privileged or unprivileged software.
MPU Configuration for a Tiva™ C Series Microcontroller
Tiva™ C Series microcontrollers have only a single processor and no caches. As a result, the MPU
should be programmed as shown in Table 3-6 on page 125.
Table 3-6. Memory Region Attributes for Tiva™ C Series Microcontrollers
Memory Region
TEX
S
C
B
Memory Type and Attributes
Flash memory
000b
0
1
0
Normal memory, non-shareable, write-through
Internal SRAM
000b
1
1
0
Normal memory, shareable, write-through
External SRAM
000b
1
1
1
Normal memory, shareable, write-back,
write-allocate
Peripherals
000b
1
0
1
Device memory, shareable
In current Tiva™ C Series microcontroller implementations, the shareability and cache policy
attributes do not affect the system behavior. However, using these settings for the MPU regions
can make the application code more portable. The values given are for typical situations.
3.1.4.3
MPU Mismatch
When an access violates the MPU permissions, the processor generates a memory management
fault (see “Exceptions and Interrupts” on page 87 for more information). The MFAULTSTAT register
indicates the cause of the fault. See page 172 for more information.
3.1.5
Floating-Point Unit (FPU)
This section describes the Floating-Point Unit (FPU) and the registers it uses. The FPU provides:
■ 32-bit instructions for single-precision (C float) data-processing operations
■ Combined multiply and accumulate instructions for increased precision (Fused MAC)
■ Hardware support for conversion, addition, subtraction, multiplication with optional accumulate,
division, and square-root
■ Hardware support for denormals and all IEEE rounding modes
■ 32 dedicated 32-bit single-precision registers, also addressable as 16 double-word registers
■ Decoupled three stage pipeline
The Cortex-M4F FPU fully supports single-precision add, subtract, multiply, divide, multiply and
accumulate, and square root operations. It also provides conversions between fixed-point and
floating-point data formats, and floating-point constant instructions. The FPU provides floating-point
computation functionality that is compliant with the ANSI/IEEE Std 754-2008, IEEE Standard for
Binary Floating-Point Arithmetic, referred to as the IEEE 754 standard. The FPU's single-precision
extension registers can also be accessed as 16 doubleword registers for load, store, and move
operations.
June 12, 2014
125
Texas Instruments-Production Data
Cortex-M4 Peripherals
3.1.5.1
FPU Views of the Register Bank
The FPU provides an extension register file containing 32 single-precision registers. These can be
viewed as:
■ Sixteen 64-bit doubleword registers, D0-D15
■ Thirty-two 32-bit single-word registers, S0-S31
■ A combination of registers from the above views
Figure 3-2. FPU Register Bank
S0
S1
S2
S3
S4
S5
S6
S7
...
S28
S29
S30
S31
D0
D1
D2
D3
...
D14
D15
The mapping between the registers is as follows:
■ S<2n> maps to the least significant half of D<n>
■ S<2n+1> maps to the most significant half of D<n>
For example, you can access the least significant half of the value in D6 by accessing S12, and the
most significant half of the elements by accessing S13.
3.1.5.2
Modes of Operation
The FPU provides three modes of operation to accommodate a variety of applications.
Full-Compliance mode. In Full-Compliance mode, the FPU processes all operations according to
the IEEE 754 standard in hardware.
Flush-to-Zero mode. Setting the FZ bit of the Floating-Point Status and Control (FPSC) register
enables Flush-to-Zero mode. In this mode, the FPU treats all subnormal input operands of arithmetic
CDP operations as zeros in the operation. Exceptions that result from a zero operand are signalled
appropriately. VABS, VNEG, and VMOV are not considered arithmetic CDP operations and are not
affected by Flush-to-Zero mode. A result that is tiny, as described in the IEEE 754 standard, where
the destination precision is smaller in magnitude than the minimum normal value before rounding,
is replaced with a zero. The IDC bit in FPSC indicates when an input flush occurs. The UFC bit in
FPSC indicates when a result flush occurs.
Default NaN mode. Setting the DN bit in the FPSC register enables default NaN mode. In this mode,
the result of any arithmetic data processing operation that involves an input NaN, or that generates
a NaN result, returns the default NaN. Propagation of the fraction bits is maintained only by VABS,
126
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
VNEG, and VMOV operations. All other CDP operations ignore any information in the fraction bits
of an input NaN.
3.1.5.3
Compliance with the IEEE 754 standard
When Default NaN (DN) and Flush-to-Zero (FZ) modes are disabled, FPv4 functionality is compliant
with the IEEE 754 standard in hardware. No support code is required to achieve this compliance.
3.1.5.4
Complete Implementation of the IEEE 754 standard
The Cortex-M4F floating point instruction set does not support all operations defined in the IEEE
754-2008 standard. Unsupported operations include, but are not limited to the following:
■ Remainder
■ Round floating-point number to integer-valued floating-point number
■ Binary-to-decimal conversions
■ Decimal-to-binary conversions
■ Direct comparison of single-precision and double-precision values
The Cortex-M4 FPU supports fused MAC operations as described in the IEEE standard. For complete
implementation of the IEEE 754-2008 standard, floating-point functionality must be augmented with
library functions.
3.1.5.5
IEEE 754 standard implementation choices
NaN handling
All single-precision values with the maximum exponent field value and a nonzero fraction field are
valid NaNs. A most-significant fraction bit of zero indicates a Signaling NaN (SNaN). A one indicates
a Quiet NaN (QNaN). Two NaN values are treated as different NaNs if they differ in any bit. The
below table shows the default NaN values.
Sign
Fraction
Fraction
0
0xFF
bit [22] = 1, bits [21:0] are all zeros
Processing of input NaNs for ARM floating-point functionality and libraries is defined as follows:
■ In full-compliance mode, NaNs are handled as described in the ARM Architecture Reference
Manual. The hardware processes the NaNs directly for arithmetic CDP instructions. For data
transfer operations, NaNs are transferred without raising the Invalid Operation exception. For
the non-arithmetic CDP instructions, VABS, VNEG, and VMOV, NaNs are copied, with a change
of sign if specified in the instructions, without causing the Invalid Operation exception.
■ In default NaN mode, arithmetic CDP instructions involving NaN operands return the default
NaN regardless of the fractions of any NaN operands. SNaNs in an arithmetic CDP operation
set the IOC flag, FPSCR[0]. NaN handling by data transfer and non-arithmetic CDP instructions
is the same as in full-compliance mode.
June 12, 2014
127
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-7. QNaN and SNaN Handling
Instruction Type
Default NaN
Mode
With QNaN Operand
With SNaN Operand
Off
The QNaN or one of the QNaN operands,
if there is more than one, is returned
according to the rules given in the ARM
Architecture Reference Manual.
IOC set. The SNaN is quieted and the
result NaN is determined by the rules
given in the ARM Architecture Reference
Manual.
On
Default NaN returns.
IOC set. Default NaN returns.
Arithmetic CDP
Non-arithmetic CDP Off/On
a
a
NaN passes to destination with sign changed as appropriate.
FCMP(Z)
-
Unordered compare.
IOC set. Unordered compare.
FCMPE(Z)
-
IOC set. Unordered compare.
IOC set. Unordered compare.
Load/store
Off/On
All NaNs transferred.
a. IOC is the Invalid Operation exception flag, FPSCR[0].
Comparisons
Comparison results modify the flags in the FPSCR. You can use the MVRS APSR_nzcv instruction
(formerly FMSTAT) to transfer the current flags from the FPSCR to the APSR. See the ARM
Architecture Reference Manual for mapping of IEEE 754-2008 standard predicates to ARM conditions.
The flags used are chosen so that subsequent conditional execution of ARM instructions can test
the predicates defined in the IEEE standard.
Underflow
The Cortex-M4F FPU uses the before rounding form of tininess and the inexact result form of loss
of accuracy as described in the IEEE 754-2008 standard to generate Underflow exceptions.
In flush-to-zero mode, results that are tiny before rounding, as described in the IEEE standard, are
flushed to a zero, and the UFC flag, FPSCR[3], is set. See the ARM Architecture Reference Manual
for information on flush-to-zero mode.
When the FPU is not in flush-to-zero mode, operations are performed on subnormal operands. If
the operation does not produce a tiny result, it returns the computed result, and the UFC flag,
FPSCR[3], is not set. The IXC flag, FPSCR[4], is set if the operation is inexact. If the operation
produces a tiny result, the result is a subnormal or zero value, and the UFC flag, FPSCR[3], is set
if the result was also inexact.
3.1.5.6
Exceptions
The FPU sets the cumulative exception status flag in the FPSCR register as required for each
instruction, in accordance with the FPv4 architecture. The FPU does not support user-mode traps.
The exception enable bits in the FPSCR read-as-zero, and writes are ignored. The processor also
has six output pins, FPIXC, FPUFC, FPOFC, FPDZC, FPIDC, and FPIOC, that each reflect the
status of one of the cumulative exception flags. For a description of these outputs, see the ARM
Cortex-M4 Integration and Implementation Manual (ARM DII 0239, available from ARM).
The processor can reduce the exception latency by using lazy stacking. See Auxiliary Control
Register, ACTLR on page 4-5. This means that the processor reserves space on the stack for the
FP state, but does not save that state information to the stack. See the ARMv7-M Architecture
Reference Manual (available from ARM) for more information.
3.1.5.7
Enabling the FPU
The FPU is disabled from reset. You must enable it before you can use any floating-point instructions.
The processor must be in privileged mode to read from and write to the Coprocessor Access
128
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Control (CPAC) register. The below example code sequence enables the FPU in both privileged
and user modes.
; CPACR is located at address 0xE000ED88
LDR.W R0, =0xE000ED88
; Read CPACR
LDR R1, [R0]
; Set bits 20-23 to enable CP10 and CP11 coprocessors
ORR R1, R1, #(0xF << 20)
; Write back the modified value to the CPACR
STR R1, [R0]; wait for store to complete
DSB
;reset pipeline now the FPU is enabled
ISB
3.2
Register Map
Table 3-8 on page 129 lists the Cortex-M4 Peripheral SysTick, NVIC, MPU, FPU and SCB registers.
The offset listed is a hexadecimal increment to the register's address, relative to the Core Peripherals
base address of 0xE000.E000.
Note:
Register spaces that are not used are reserved for future or internal use. Software should
not modify any reserved memory address.
Table 3-8. Peripherals Register Map
Offset
Name
Type
Reset
Description
See
page
System Timer (SysTick) Registers
0x010
STCTRL
RW
0x0000.0004
SysTick Control and Status Register
133
0x014
STRELOAD
RW
-
SysTick Reload Value Register
135
0x018
STCURRENT
RWC
-
SysTick Current Value Register
136
Nested Vectored Interrupt Controller (NVIC) Registers
0x100
EN0
RW
0x0000.0000
Interrupt 0-31 Set Enable
137
0x104
EN1
RW
0x0000.0000
Interrupt 32-63 Set Enable
137
0x108
EN2
RW
0x0000.0000
Interrupt 64-95 Set Enable
137
0x10C
EN3
RW
0x0000.0000
Interrupt 96-127 Set Enable
137
0x110
EN4
RW
0x0000.0000
Interrupt 128-138 Set Enable
138
0x180
DIS0
RW
0x0000.0000
Interrupt 0-31 Clear Enable
139
0x184
DIS1
RW
0x0000.0000
Interrupt 32-63 Clear Enable
139
0x188
DIS2
RW
0x0000.0000
Interrupt 64-95 Clear Enable
139
0x18C
DIS3
RW
0x0000.0000
Interrupt 96-127 Clear Enable
139
0x190
DIS4
RW
0x0000.0000
Interrupt 128-138 Clear Enable
140
0x200
PEND0
RW
0x0000.0000
Interrupt 0-31 Set Pending
141
0x204
PEND1
RW
0x0000.0000
Interrupt 32-63 Set Pending
141
June 12, 2014
129
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-8. Peripherals Register Map (continued)
Offset
Name
0x208
Description
See
page
Type
Reset
PEND2
RW
0x0000.0000
Interrupt 64-95 Set Pending
141
0x20C
PEND3
RW
0x0000.0000
Interrupt 96-127 Set Pending
141
0x210
PEND4
RW
0x0000.0000
Interrupt 128-138 Set Pending
142
0x280
UNPEND0
RW
0x0000.0000
Interrupt 0-31 Clear Pending
143
0x284
UNPEND1
RW
0x0000.0000
Interrupt 32-63 Clear Pending
143
0x288
UNPEND2
RW
0x0000.0000
Interrupt 64-95 Clear Pending
143
0x28C
UNPEND3
RW
0x0000.0000
Interrupt 96-127 Clear Pending
143
0x290
UNPEND4
RW
0x0000.0000
Interrupt 128-138 Clear Pending
144
0x300
ACTIVE0
RO
0x0000.0000
Interrupt 0-31 Active Bit
145
0x304
ACTIVE1
RO
0x0000.0000
Interrupt 32-63 Active Bit
145
0x308
ACTIVE2
RO
0x0000.0000
Interrupt 64-95 Active Bit
145
0x30C
ACTIVE3
RO
0x0000.0000
Interrupt 96-127 Active Bit
145
0x310
ACTIVE4
RO
0x0000.0000
Interrupt 128-138 Active Bit
146
0x400
PRI0
RW
0x0000.0000
Interrupt 0-3 Priority
147
0x404
PRI1
RW
0x0000.0000
Interrupt 4-7 Priority
147
0x408
PRI2
RW
0x0000.0000
Interrupt 8-11 Priority
147
0x40C
PRI3
RW
0x0000.0000
Interrupt 12-15 Priority
147
0x410
PRI4
RW
0x0000.0000
Interrupt 16-19 Priority
147
0x414
PRI5
RW
0x0000.0000
Interrupt 20-23 Priority
147
0x418
PRI6
RW
0x0000.0000
Interrupt 24-27 Priority
147
0x41C
PRI7
RW
0x0000.0000
Interrupt 28-31 Priority
147
0x420
PRI8
RW
0x0000.0000
Interrupt 32-35 Priority
147
0x424
PRI9
RW
0x0000.0000
Interrupt 36-39 Priority
147
0x428
PRI10
RW
0x0000.0000
Interrupt 40-43 Priority
147
0x42C
PRI11
RW
0x0000.0000
Interrupt 44-47 Priority
147
0x430
PRI12
RW
0x0000.0000
Interrupt 48-51 Priority
147
0x434
PRI13
RW
0x0000.0000
Interrupt 52-55 Priority
147
0x438
PRI14
RW
0x0000.0000
Interrupt 56-59 Priority
147
0x43C
PRI15
RW
0x0000.0000
Interrupt 60-63 Priority
147
0x440
PRI16
RW
0x0000.0000
Interrupt 64-67 Priority
149
0x444
PRI17
RW
0x0000.0000
Interrupt 68-71 Priority
149
0x448
PRI18
RW
0x0000.0000
Interrupt 72-75 Priority
149
130
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 3-8. Peripherals Register Map (continued)
Description
See
page
Offset
Name
Type
Reset
0x44C
PRI19
RW
0x0000.0000
Interrupt 76-79 Priority
149
0x450
PRI20
RW
0x0000.0000
Interrupt 80-83 Priority
149
0x454
PRI21
RW
0x0000.0000
Interrupt 84-87 Priority
149
0x458
PRI22
RW
0x0000.0000
Interrupt 88-91 Priority
149
0x45C
PRI23
RW
0x0000.0000
Interrupt 92-95 Priority
149
0x460
PRI24
RW
0x0000.0000
Interrupt 96-99 Priority
149
0x464
PRI25
RW
0x0000.0000
Interrupt 100-103 Priority
149
0x468
PRI26
RW
0x0000.0000
Interrupt 104-107 Priority
149
0x46C
PRI27
RW
0x0000.0000
Interrupt 108-111 Priority
149
0x470
PRI28
RW
0x0000.0000
Interrupt 112-115 Priority
149
0x474
PRI29
RW
0x0000.0000
Interrupt 116-119 Priority
149
0x478
PRI30
RW
0x0000.0000
Interrupt 120-123 Priority
149
0x47C
PRI31
RW
0x0000.0000
Interrupt 124-127 Priority
149
0x480
PRI32
RW
0x0000.0000
Interrupt 128-131 Priority
149
0x484
PRI33
RW
0x0000.0000
Interrupt 132-135 Priority
149
0x488
PRI34
RW
0x0000.0000
Interrupt 136-138 Priority
149
0xF00
SWTRIG
WO
0x0000.0000
Software Trigger Interrupt
151
System Control Block (SCB) Registers
0x008
ACTLR
RW
0x0000.0000
Auxiliary Control
152
0xD00
CPUID
RO
0x410F.C241
CPU ID Base
154
0xD04
INTCTRL
RW
0x0000.0000
Interrupt Control and State
155
0xD08
VTABLE
RW
0x0000.0000
Vector Table Offset
158
0xD0C
APINT
RW
0xFA05.0000
Application Interrupt and Reset Control
159
0xD10
SYSCTRL
RW
0x0000.0000
System Control
161
0xD14
CFGCTRL
RW
0x0000.0200
Configuration and Control
163
0xD18
SYSPRI1
RW
0x0000.0000
System Handler Priority 1
165
0xD1C
SYSPRI2
RW
0x0000.0000
System Handler Priority 2
166
0xD20
SYSPRI3
RW
0x0000.0000
System Handler Priority 3
167
0xD24
SYSHNDCTRL
RW
0x0000.0000
System Handler Control and State
168
0xD28
FAULTSTAT
RW1C
0x0000.0000
Configurable Fault Status
172
0xD2C
HFAULTSTAT
RW1C
0x0000.0000
Hard Fault Status
178
0xD34
MMADDR
RW
-
Memory Management Fault Address
179
June 12, 2014
131
Texas Instruments-Production Data
Cortex-M4 Peripherals
Table 3-8. Peripherals Register Map (continued)
Offset
Name
0xD38
FAULTADDR
Type
Reset
RW
-
Description
See
page
Bus Fault Address
180
Memory Protection Unit (MPU) Registers
0xD90
MPUTYPE
RO
0x0000.0800
MPU Type
181
0xD94
MPUCTRL
RW
0x0000.0000
MPU Control
182
0xD98
MPUNUMBER
RW
0x0000.0000
MPU Region Number
184
0xD9C
MPUBASE
RW
0x0000.0000
MPU Region Base Address
185
0xDA0
MPUATTR
RW
0x0000.0000
MPU Region Attribute and Size
187
0xDA4
MPUBASE1
RW
0x0000.0000
MPU Region Base Address Alias 1
185
0xDA8
MPUATTR1
RW
0x0000.0000
MPU Region Attribute and Size Alias 1
187
0xDAC
MPUBASE2
RW
0x0000.0000
MPU Region Base Address Alias 2
185
0xDB0
MPUATTR2
RW
0x0000.0000
MPU Region Attribute and Size Alias 2
187
0xDB4
MPUBASE3
RW
0x0000.0000
MPU Region Base Address Alias 3
185
0xDB8
MPUATTR3
RW
0x0000.0000
MPU Region Attribute and Size Alias 3
187
Floating-Point Unit (FPU) Registers
0xD88
CPAC
RW
0x0000.0000
Coprocessor Access Control
190
0xF34
FPCC
RW
0xC000.0000
Floating-Point Context Control
191
0xF38
FPCA
RW
-
Floating-Point Context Address
193
0xF3C
FPDSC
RW
0x0000.0000
Floating-Point Default Status Control
194
3.3
System Timer (SysTick) Register Descriptions
This section lists and describes the System Timer registers, in numerical order by address offset.
132
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 1: SysTick Control and Status Register (STCTRL), offset 0x010
Note:
This register can only be accessed from privileged mode.
The SysTick STCTRL register enables the SysTick features.
SysTick Control and Status Register (STCTRL)
Base 0xE000.E000
Offset 0x010
Type RW, reset 0x0000.0004
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
16
COUNT
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
2
1
0
CLK_SRC
INTEN
ENABLE
RW
1
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:17
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
16
COUNT
RO
0
Count Flag
Value
Description
0
The SysTick timer has not counted to 0 since the last time
this bit was read.
1
The SysTick timer has counted to 0 since the last time
this bit was read.
This bit is cleared by a read of the register or if the STCURRENT register
is written with any value.
If read by the debugger using the DAP, this bit is cleared only if the
MasterType bit in the AHB-AP Control Register is clear. Otherwise,
the COUNT bit is not changed by the debugger read. See the ARM®
Debug Interface V5 Architecture Specification for more information on
MasterType.
15:3
reserved
RO
0x000
2
CLK_SRC
RW
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Clock Source
Value Description
0
Precision internal oscillator (PIOSC) divided by 4
1
System clock
June 12, 2014
133
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
1
INTEN
RW
0
0
ENABLE
RW
0
Description
Interrupt Enable
Value
Description
0
Interrupt generation is disabled. Software can use the
COUNT bit to determine if the counter has ever reached 0.
1
An interrupt is generated to the NVIC when SysTick counts
to 0.
Enable
Value
Description
0
The counter is disabled.
1
Enables SysTick to operate in a multi-shot way. That is, the
counter loads the RELOAD value and begins counting down.
On reaching 0, the COUNT bit is set and an interrupt is
generated if enabled by INTEN. The counter then loads the
RELOAD value again and begins counting.
134
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 2: SysTick Reload Value Register (STRELOAD), offset 0x014
Note:
This register can only be accessed from privileged mode.
The STRELOAD register specifies the start value to load into the SysTick Current Value
(STCURRENT) register when the counter reaches 0. The start value can be between 0x1 and
0x00FF.FFFF. A start value of 0 is possible but has no effect because the SysTick interrupt and the
COUNT bit are activated when counting from 1 to 0.
SysTick can be configured as a multi-shot timer, repeated over and over, firing every N+1 clock
pulses, where N is any value from 1 to 0x00FF.FFFF. For example, if a tick interrupt is required
every 100 clock pulses, 99 must be written into the RELOAD field.
Note that in order to access this register correctly, the system clock must be faster than 8 MHz.
SysTick Reload Value Register (STRELOAD)
Base 0xE000.E000
Offset 0x014
Type RW, reset 31
30
29
28
27
26
25
24
23
22
21
20
reserved
Type
Reset
19
18
17
16
RELOAD
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RELOAD
Type
Reset
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:0
RELOAD
RW
0x00.0000
Reload Value
Value to load into the SysTick Current Value (STCURRENT) register
when the counter reaches 0.
June 12, 2014
135
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 3: SysTick Current Value Register (STCURRENT), offset 0x018
Note:
This register can only be accessed from privileged mode.
The STCURRENT register contains the current value of the SysTick counter.
SysTick Current Value Register (STCURRENT)
Base 0xE000.E000
Offset 0x018
Type RWC, reset 31
30
29
28
27
26
25
24
23
22
21
reserved
Type
Reset
20
19
18
17
16
CURRENT
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
CURRENT
Type
Reset
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
RWC
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:0
CURRENT
RWC
0x00.0000
Current Value
This field contains the current value at the time the register is accessed.
No read-modify-write protection is provided, so change with care.
This register is write-clear. Writing to it with any value clears the register.
Clearing this register also clears the COUNT bit of the STCTRL register.
3.4
NVIC Register Descriptions
This section lists and describes the NVIC registers, in numerical order by address offset.
The NVIC registers can only be fully accessed from privileged mode, but interrupts can be pended
while in unprivileged mode by enabling the Configuration and Control (CFGCTRL) register. Any
other unprivileged mode access causes a bus fault.
Ensure software uses correctly aligned register accesses. The processor does not support unaligned
accesses to NVIC registers.
An interrupt can enter the pending state even if it is disabled.
Before programming the VTABLE register to relocate the vector table, ensure the vector table
entries of the new vector table are set up for fault handlers, NMI, and all enabled exceptions such
as interrupts. For more information, see page 158.
136
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 4: Interrupt 0-31 Set Enable (EN0), offset 0x100
Register 5: Interrupt 32-63 Set Enable (EN1), offset 0x104
Register 6: Interrupt 64-95 Set Enable (EN2), offset 0x108
Register 7: Interrupt 96-127 Set Enable (EN3), offset 0x10C
Note:
This register can only be accessed from privileged mode.
The ENn registers enable interrupts and show which interrupts are enabled. Bit 0 of EN0 corresponds
to Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of EN1 corresponds to Interrupt 32; bit 31
corresponds to Interrupt 63. Bit 0 of EN2 corresponds to Interrupt 64; bit 31 corresponds to Interrupt
95. Bit 0 of EN3 corresponds to Interrupt 96; bit 31 corresponds to Interrupt 127. Bit 0 of EN4 (see
page 138) corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 99 for interrupt assignments.
If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt
is not enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC
never activates the interrupt, regardless of its priority.
Interrupt 0-31 Set Enable (EN0)
Base 0xE000.E000
Offset 0x100
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
INT
Type
Reset
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
INT
Type
Reset
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
31:0
INT
RW
RW
0
Reset
RW
0
Description
0x0000.0000 Interrupt Enable
Value
Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, enables the interrupt.
A bit can only be cleared by setting the corresponding INT[n] bit in
the DISn register.
June 12, 2014
137
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 8: Interrupt 128-138 Set Enable (EN4), offset 0x110
Note:
This register can only be accessed from privileged mode.
The EN4 register enables interrupts and shows which interrupts are enabled. Bit 0 corresponds to
Interrupt 128; bit 10 corresponds to Interrupt 138. See Table 2-9 on page 99 for interrupt assignments.
If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt
is not enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC
never activates the interrupt, regardless of its priority.
Interrupt 128-138 Set Enable (EN4)
Base 0xE000.E000
Offset 0x110
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
INT
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
RW
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Enable
Value
Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, enables the interrupt.
A bit can only be cleared by setting the corresponding INT[n] bit in
the DIS4 register.
138
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 9: Interrupt 0-31 Clear Enable (DIS0), offset 0x180
Register 10: Interrupt 32-63 Clear Enable (DIS1), offset 0x184
Register 11: Interrupt 64-95 Clear Enable (DIS2), offset 0x188
Register 12: Interrupt 96-127 Clear Enable (DIS3), offset 0x18C
Note:
This register can only be accessed from privileged mode.
The DISn registers disable interrupts. Bit 0 of DIS0 corresponds to Interrupt 0; bit 31 corresponds
to Interrupt 31. Bit 0 of DIS1 corresponds to Interrupt 32; bit 31 corresponds to Interrupt 63. Bit 0 of
DIS2 corresponds to Interrupt 64; bit 31 corresponds to Interrupt 95. Bit 0 of DIS3 corresponds to
Interrupt 96; bit 31 corresponds to Interrupt 127. Bit 0 of DIS4 (see page 140) corresponds to Interrupt
128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 99 for interrupt assignments.
Interrupt 0-31 Clear Enable (DIS0)
Base 0xE000.E000
Offset 0x180
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
RW
Reset
Description
0x0000.0000 Interrupt Disable
Value Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, clears the corresponding INT[n] bit in the EN0
register, disabling interrupt [n].
June 12, 2014
139
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 13: Interrupt 128-138 Clear Enable (DIS4), offset 0x190
Note:
This register can only be accessed from privileged mode.
The DIS4 register disables interrupts. Bit 0 corresponds to Interrupt 128; bit 10 corresponds to
Interrupt 138. See Table 2-9 on page 99 for interrupt assignments.
Interrupt 128-138 Clear Enable (DIS4)
Base 0xE000.E000
Offset 0x190
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
RW
0x0
RW
0
RW
0
RW
0
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Disable
Value Description
0
On a read, indicates the interrupt is disabled.
On a write, no effect.
1
On a read, indicates the interrupt is enabled.
On a write, clears the corresponding INT[n] bit in the EN4
register, disabling interrupt [n].
140
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 14: Interrupt 0-31 Set Pending (PEND0), offset 0x200
Register 15: Interrupt 32-63 Set Pending (PEND1), offset 0x204
Register 16: Interrupt 64-95 Set Pending (PEND2), offset 0x208
Register 17: Interrupt 96-127 Set Pending (PEND3), offset 0x20C
Note:
This register can only be accessed from privileged mode.
The PENDn registers force interrupts into the pending state and show which interrupts are pending.
Bit 0 of PEND0 corresponds to Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of PEND1
corresponds to Interrupt 32; bit 31 corresponds to Interrupt 63. Bit 0 of PEND2 corresponds to
Interrupt 64; bit 31 corresponds to Interrupt 95. Bit 0 of PEND3 corresponds to Interrupt 96; bit 31
corresponds to Interrupt 127. Bit 0 of PEND4 (see page 142) corresponds to Interrupt 128; bit 10
corresponds to Interrupt 138.
See Table 2-9 on page 99 for interrupt assignments.
Interrupt 0-31 Set Pending (PEND0)
Base 0xE000.E000
Offset 0x200
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
RW
Reset
Description
0x0000.0000 Interrupt Set Pending
Value
Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, the corresponding interrupt is set to pending
even if it is disabled.
If the corresponding interrupt is already pending, setting a bit has no
effect.
A bit can only be cleared by setting the corresponding INT[n] bit in
the UNPEND0 register.
June 12, 2014
141
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 18: Interrupt 128-138 Set Pending (PEND4), offset 0x210
Note:
This register can only be accessed from privileged mode.
The PEND4 register forces interrupts into the pending state and shows which interrupts are pending.
Bit 0 corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138. See Table 2-9 on page 99
for interrupt assignments.
Interrupt 128-138 Set Pending (PEND4)
Base 0xE000.E000
Offset 0x210
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
RW
0x0
RW
0
RW
0
RW
0
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Set Pending
Value
Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, the corresponding interrupt is set to pending
even if it is disabled.
If the corresponding interrupt is already pending, setting a bit has no
effect.
A bit can only be cleared by setting the corresponding INT[n] bit in
the UNPEND4 register.
142
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 19: Interrupt 0-31 Clear Pending (UNPEND0), offset 0x280
Register 20: Interrupt 32-63 Clear Pending (UNPEND1), offset 0x284
Register 21: Interrupt 64-95 Clear Pending (UNPEND2), offset 0x288
Register 22: Interrupt 96-127 Clear Pending (UNPEND3), offset 0x28C
Note:
This register can only be accessed from privileged mode.
The UNPENDn registers show which interrupts are pending and remove the pending state from
interrupts. Bit 0 of UNPEND0 corresponds to Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of
UNPEND1 corresponds to Interrupt 32; bit 31 corresponds to Interrupt 63. Bit 0 of UNPEND2
corresponds to Interrupt 64; bit 31 corresponds to Interrupt 95. Bit 0 of UNPEND3 corresponds to
Interrupt 96; bit 31 corresponds to Interrupt 127. Bit 0 of UNPEND4 (see page 144) corresponds to
Interrupt 128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 99 for interrupt assignments.
Interrupt 0-31 Clear Pending (UNPEND0)
Base 0xE000.E000
Offset 0x280
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
RW
Reset
Description
0x0000.0000 Interrupt Clear Pending
Value Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, clears the corresponding INT[n] bit in the PEND0
register, so that interrupt [n] is no longer pending.
Setting a bit does not affect the active state of the corresponding
interrupt.
June 12, 2014
143
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 23: Interrupt 128-138 Clear Pending (UNPEND4), offset 0x290
Note:
This register can only be accessed from privileged mode.
The UNPEND4 register shows which interrupts are pending and removes the pending state from
interrupts. Bit 0 corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138. See Table
2-9 on page 99 for interrupt assignments.
Interrupt 128-138 Clear Pending (UNPEND4)
Base 0xE000.E000
Offset 0x290
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
RW
0x0
RW
0
RW
0
RW
0
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Clear Pending
Value Description
0
On a read, indicates that the interrupt is not pending.
On a write, no effect.
1
On a read, indicates that the interrupt is pending.
On a write, clears the corresponding INT[n] bit in the PEND4
register, so that interrupt [n] is no longer pending.
Setting a bit does not affect the active state of the corresponding
interrupt.
144
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 24: Interrupt 0-31 Active Bit (ACTIVE0), offset 0x300
Register 25: Interrupt 32-63 Active Bit (ACTIVE1), offset 0x304
Register 26: Interrupt 64-95 Active Bit (ACTIVE2), offset 0x308
Register 27: Interrupt 96-127 Active Bit (ACTIVE3), offset 0x30C
Note:
This register can only be accessed from privileged mode.
The UNPENDn registers indicate which interrupts are active. Bit 0 of ACTIVE0 corresponds to
Interrupt 0; bit 31 corresponds to Interrupt 31. Bit 0 of ACTIVE1 corresponds to Interrupt 32; bit 31
corresponds to Interrupt 63. Bit 0 of ACTIVE2 corresponds to Interrupt 64; bit 31 corresponds to
Interrupt 95. Bit 0 of ACTIVE3 corresponds to Interrupt 96; bit 31 corresponds to Interrupt 127. Bit
0 of ACTIVE4 (see page 146) corresponds to Interrupt 128; bit 10 corresponds to Interrupt 138.
See Table 2-9 on page 99 for interrupt assignments.
Caution – Do not manually set or clear the bits in this register.
Interrupt 0-31 Active Bit (ACTIVE0)
Base 0xE000.E000
Offset 0x300
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
INT
Type
Reset
INT
Type
Reset
Bit/Field
Name
Type
31:0
INT
RO
Reset
Description
0x0000.0000 Interrupt Active
Value Description
0
The corresponding interrupt is not active.
1
The corresponding interrupt is active, or active and pending.
June 12, 2014
145
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 28: Interrupt 128-138 Active Bit (ACTIVE4), offset 0x310
Note:
This register can only be accessed from privileged mode.
The ACTIVE4 register indicates which interrupts are active. Bit 0 corresponds to Interrupt 128; bit
10 corresponds to Interrupt 131. See Table 2-9 on page 99 for interrupt assignments.
Caution – Do not manually set or clear the bits in this register.
Interrupt 128-138 Active Bit (ACTIVE4)
Base 0xE000.E000
Offset 0x310
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
15
14
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
INT
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:11
reserved
RO
0x0000.000
10:0
INT
RO
0x0
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt Active
Value Description
0
The corresponding interrupt is not active.
1
The corresponding interrupt is active, or active and pending.
146
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 29: Interrupt 0-3 Priority (PRI0), offset 0x400
Register 30: Interrupt 4-7 Priority (PRI1), offset 0x404
Register 31: Interrupt 8-11 Priority (PRI2), offset 0x408
Register 32: Interrupt 12-15 Priority (PRI3), offset 0x40C
Register 33: Interrupt 16-19 Priority (PRI4), offset 0x410
Register 34: Interrupt 20-23 Priority (PRI5), offset 0x414
Register 35: Interrupt 24-27 Priority (PRI6), offset 0x418
Register 36: Interrupt 28-31 Priority (PRI7), offset 0x41C
Register 37: Interrupt 32-35 Priority (PRI8), offset 0x420
Register 38: Interrupt 36-39 Priority (PRI9), offset 0x424
Register 39: Interrupt 40-43 Priority (PRI10), offset 0x428
Register 40: Interrupt 44-47 Priority (PRI11), offset 0x42C
Register 41: Interrupt 48-51 Priority (PRI12), offset 0x430
Register 42: Interrupt 52-55 Priority (PRI13), offset 0x434
Register 43: Interrupt 56-59 Priority (PRI14), offset 0x438
Register 44: Interrupt 60-63 Priority (PRI15), offset 0x43C
Note:
This register can only be accessed from privileged mode.
The PRIn registers (see also page 149) provide 3-bit priority fields for each interrupt. These registers
are byte accessible. Each register holds four priority fields that are assigned to interrupts as follows:
PRIn Register Bit Field
Interrupt
Bits 31:29
Interrupt [4n+3]
Bits 23:21
Interrupt [4n+2]
Bits 15:13
Interrupt [4n+1]
Bits 7:5
Interrupt [4n]
See Table 2-9 on page 99 for interrupt assignments.
Each priority level can be split into separate group priority and subpriority fields. The PRIGROUP
field in the Application Interrupt and Reset Control (APINT) register (see page 159) indicates the
position of the binary point that splits the priority and subpriority fields.
These registers can only be accessed from privileged mode.
June 12, 2014
147
Texas Instruments-Production Data
Cortex-M4 Peripherals
Interrupt 0-3 Priority (PRI0)
Base 0xE000.E000
Offset 0x400
Type RW, reset 0x0000.0000
31
30
29
28
27
INTD
Type
Reset
25
24
23
reserved
22
21
20
19
INTC
18
17
16
reserved
RW
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
INTB
Type
Reset
26
RW
0
RW
0
reserved
RO
0
INTA
Bit/Field
Name
Type
Reset
31:29
INTD
RW
0x0
RW
0
reserved
RO
0
Description
Interrupt Priority for Interrupt [4n+3]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+3], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
28:24
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
INTC
RW
0x0
Interrupt Priority for Interrupt [4n+2]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+2], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
20:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:13
INTB
RW
0x0
Interrupt Priority for Interrupt [4n+1]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+1], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
12:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:5
INTA
RW
0x0
Interrupt Priority for Interrupt [4n]
This field holds a priority value, 0-7, for the interrupt with the number
[4n], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
4:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
148
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 45: Interrupt 64-67 Priority (PRI16), offset 0x440
Register 46: Interrupt 68-71 Priority (PRI17), offset 0x444
Register 47: Interrupt 72-75 Priority (PRI18), offset 0x448
Register 48: Interrupt 76-79 Priority (PRI19), offset 0x44C
Register 49: Interrupt 80-83 Priority (PRI20), offset 0x450
Register 50: Interrupt 84-87 Priority (PRI21), offset 0x454
Register 51: Interrupt 88-91 Priority (PRI22), offset 0x458
Register 52: Interrupt 92-95 Priority (PRI23), offset 0x45C
Register 53: Interrupt 96-99 Priority (PRI24), offset 0x460
Register 54: Interrupt 100-103 Priority (PRI25), offset 0x464
Register 55: Interrupt 104-107 Priority (PRI26), offset 0x468
Register 56: Interrupt 108-111 Priority (PRI27), offset 0x46C
Register 57: Interrupt 112-115 Priority (PRI28), offset 0x470
Register 58: Interrupt 116-119 Priority (PRI29), offset 0x474
Register 59: Interrupt 120-123 Priority (PRI30), offset 0x478
Register 60: Interrupt 124-127 Priority (PRI31), offset 0x47C
Register 61: Interrupt 128-131 Priority (PRI32), offset 0x480
Register 62: Interrupt 132-135 Priority (PRI33), offset 0x484
Register 63: Interrupt 136-138 Priority (PRI34), offset 0x488
Note:
This register can only be accessed from privileged mode.
The PRIn registers (see also page 147) provide 3-bit priority fields for each interrupt. These registers
are byte accessible. Each register holds four priority fields that are assigned to interrupts as follows:
PRIn Register Bit Field
Interrupt
Bits 31:29
Interrupt [4n+3]
Bits 23:21
Interrupt [4n+2]
Bits 15:13
Interrupt [4n+1]
Bits 7:5
Interrupt [4n]
See Table 2-9 on page 99 for interrupt assignments.
Each priority level can be split into separate group priority and subpriority fields. The PRIGROUP
field in the Application Interrupt and Reset Control (APINT) register (see page 159) indicates the
position of the binary point that splits the priority and subpriority fields .
These registers can only be accessed from privileged mode.
June 12, 2014
149
Texas Instruments-Production Data
Cortex-M4 Peripherals
Interrupt 64-67 Priority (PRI16)
Base 0xE000.E000
Offset 0x440
Type RW, reset 0x0000.0000
31
30
29
28
27
INTD
Type
Reset
25
24
23
reserved
22
21
20
19
INTC
18
17
16
reserved
RW
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
INTB
Type
Reset
26
RW
0
RW
0
reserved
RO
0
INTA
Bit/Field
Name
Type
Reset
31:29
INTD
RW
0x0
RW
0
reserved
RO
0
Description
Interrupt Priority for Interrupt [4n+3]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+3], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
28:24
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
INTC
RW
0x0
Interrupt Priority for Interrupt [4n+2]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+2], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
20:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:13
INTB
RW
0x0
Interrupt Priority for Interrupt [4n+1]
This field holds a priority value, 0-7, for the interrupt with the number
[4n+1], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
12:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:5
INTA
RW
0x0
Interrupt Priority for Interrupt [4n]
This field holds a priority value, 0-7, for the interrupt with the number
[4n], where n is the number of the Interrupt Priority register (n=0 for
PRI0, and so on). The lower the value, the greater the priority of the
corresponding interrupt.
4:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
150
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 64: Software Trigger Interrupt (SWTRIG), offset 0xF00
Note:
Only privileged software can enable unprivileged access to the SWTRIG register.
Writing an interrupt number to the SWTRIG register generates a Software Generated Interrupt (SGI).
See Table 2-9 on page 99 for interrupt assignments.
When the MAINPEND bit in the Configuration and Control (CFGCTRL) register (see page 163) is
set, unprivileged software can access the SWTRIG register.
Software Trigger Interrupt (SWTRIG)
Base 0xE000.E000
Offset 0xF00
Type WO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
WO
0
WO
0
WO
0
WO
0
WO
0
WO
0
WO
0
WO
0
reserved
Type
Reset
reserved
Type
Reset
INTID
RO
0
Bit/Field
Name
Type
Reset
31:8
reserved
RO
0x0000.00
7:0
INTID
WO
0x00
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Interrupt ID
This field holds the interrupt ID of the required SGI. For example, a value
of 0x3 generates an interrupt on IRQ3.
3.5
System Control Block (SCB) Register Descriptions
This section lists and describes the System Control Block (SCB) registers, in numerical order by
address offset. The SCB registers can only be accessed from privileged mode.
All registers must be accessed with aligned word accesses except for the FAULTSTAT and
SYSPRI1-SYSPRI3 registers, which can be accessed with byte or aligned halfword or word accesses.
The processor does not support unaligned accesses to system control block registers.
June 12, 2014
151
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 65: Auxiliary Control (ACTLR), offset 0x008
Note:
This register can only be accessed from privileged mode.
The ACTLR register provides disable bits for IT folding, write buffer use for accesses to the default
memory map, and interruption of multi-cycle instructions. By default, this register is set to provide
optimum performance from the Cortex-M4 processor and does not normally require modification.
Auxiliary Control (ACTLR)
Base 0xE000.E000
Offset 0x008
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
DISOOFP DISFPCA
RO
0
RO
0
RW
0
RW
0
reserved
RO
0
RO
0
RO
0
DISFOLD DISWBUF DISMCYC
RO
0
RO
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:10
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
9
DISOOFP
RW
0
Disable Out-Of-Order Floating Point
Disables floating-point instructions completing out of order with respect
to integer instructions.
8
DISFPCA
RW
0
Disable CONTROL.FPCA
Disable automatic update of the FPCA bit in the CONTROL register.
Important:
7:3
reserved
RO
0x00
2
DISFOLD
RW
0
Two bits control when FPCA can be enabled: the ASPEN
bit in the Floating-Point Context Control (FPCC)
register and the DISFPCA bit in the Auxiliary Control
(ACTLR) register.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Disable IT Folding
Value Description
0
No effect.
1
Disables IT folding.
In some situations, the processor can start executing the first instruction
in an IT block while it is still executing the IT instruction. This behavior
is called IT folding, and improves performance, However, IT folding can
cause jitter in looping. If a task must avoid jitter, set the DISFOLD bit
before executing the task, to disable IT folding.
152
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
1
DISWBUF
RW
0
Description
Disable Write Buffer
Value Description
0
No effect.
1
Disables write buffer use during default memory map accesses.
In this situation, all bus faults are precise bus faults but
performance is decreased because any store to memory must
complete before the processor can execute the next instruction.
Note:
0
DISMCYC
RW
0
This bit only affects write buffers implemented in the
Cortex-M4 processor.
Disable Interrupts of Multiple Cycle Instructions
Value Description
0
No effect.
1
Disables interruption of load multiple and store multiple
instructions. In this situation, the interrupt latency of the
processor is increased because any LDM or STM must complete
before the processor can stack the current state and enter the
interrupt handler.
June 12, 2014
153
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 66: CPU ID Base (CPUID), offset 0xD00
Note:
This register can only be accessed from privileged mode.
The CPUID register contains the ARM® Cortex™-M4 processor part number, version, and
implementation information.
CPU ID Base (CPUID)
Base 0xE000.E000
Offset 0xD00
Type RO, reset 0x410F.C241
31
30
29
28
27
26
25
24
23
22
IMP
Type
Reset
21
20
19
18
VAR
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
PARTNO
Type
Reset
RO
1
RO
1
RO
0
RO
0
RO
0
RO
0
RO
1
17
16
RO
1
RO
1
1
0
RO
0
RO
1
CON
REV
RO
0
RO
0
RO
1
Bit/Field
Name
Type
Reset
Description
31:24
IMP
RO
0x41
Implementer Code
RO
0
RO
0
RO
0
RO
0
Value Description
0x41 ARM
23:20
VAR
RO
0x0
Variant Number
Value Description
0x0
19:16
CON
RO
0xF
The rn value in the rnpn product revision identifier, for example,
the 0 in r0p0.
Constant
Value Description
0xF
15:4
PARTNO
RO
0xC24
Always reads as 0xF.
Part Number
Value Description
0xC24 Cortex-M4 processor.
3:0
REV
RO
0x1
Revision Number
Value Description
0x1
The pn value in the rnpn product revision identifier, for example,
the 1 in r0p1.
154
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 67: Interrupt Control and State (INTCTRL), offset 0xD04
Note:
This register can only be accessed from privileged mode.
The INCTRL register provides a set-pending bit for the NMI exception, and set-pending and
clear-pending bits for the PendSV and SysTick exceptions. In addition, bits in this register indicate
the exception number of the exception being processed, whether there are preempted active
exceptions, the exception number of the highest priority pending exception, and whether any interrupts
are pending.
When writing to INCTRL, the effect is unpredictable when writing a 1 to both the PENDSV and
UNPENDSV bits, or writing a 1 to both the PENDSTSET and PENDSTCLR bits.
Interrupt Control and State (INTCTRL)
Base 0xE000.E000
Offset 0xD04
Type RW, reset 0x0000.0000
31
30
NMISET
Type
Reset
29
reserved
28
26
PENDSV UNPENDSV
25
PENDSTSET PENDSTCLR
24
reserved
23
22
21
ISRPRE ISRPEND
20
19
18
reserved
17
16
VECPEND
RW
0
RO
0
RO
0
RW
0
WO
0
RW
0
WO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
VECPEND
Type
Reset
27
RO
0
RETBASE
RO
0
reserved
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31
NMISET
RW
0
VECACT
Description
NMI Set Pending
Value Description
0
On a read, indicates an NMI exception is not pending.
On a write, no effect.
1
On a read, indicates an NMI exception is pending.
On a write, changes the NMI exception state to pending.
Because NMI is the highest-priority exception, normally the processor
enters the NMI exception handler as soon as it registers the setting of
this bit, and clears this bit on entering the interrupt handler. A read of
this bit by the NMI exception handler returns 1 only if the NMI signal is
reasserted while the processor is executing that handler.
30:29
reserved
RO
0x0
28
PENDSV
RW
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PendSV Set Pending
Value Description
0
On a read, indicates a PendSV exception is not pending.
On a write, no effect.
1
On a read, indicates a PendSV exception is pending.
On a write, changes the PendSV exception state to pending.
Setting this bit is the only way to set the PendSV exception state to
pending. This bit is cleared by writing a 1 to the UNPENDSV bit.
June 12, 2014
155
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
27
UNPENDSV
WO
0
Description
PendSV Clear Pending
Value Description
0
On a write, no effect.
1
On a write, removes the pending state from the PendSV
exception.
This bit is write only; on a register read, its value is unknown.
26
PENDSTSET
RW
0
SysTick Set Pending
Value Description
0
On a read, indicates a SysTick exception is not pending.
On a write, no effect.
1
On a read, indicates a SysTick exception is pending.
On a write, changes the SysTick exception state to pending.
This bit is cleared by writing a 1 to the PENDSTCLR bit.
25
PENDSTCLR
WO
0
SysTick Clear Pending
Value Description
0
On a write, no effect.
1
On a write, removes the pending state from the SysTick
exception.
This bit is write only; on a register read, its value is unknown.
24
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23
ISRPRE
RO
0
Debug Interrupt Handling
Value Description
0
The release from halt does not take an interrupt.
1
The release from halt takes an interrupt.
This bit is only meaningful in Debug mode and reads as zero when the
processor is not in Debug mode.
22
ISRPEND
RO
0
Interrupt Pending
Value Description
0
No interrupt is pending.
1
An interrupt is pending.
This bit provides status for all interrupts excluding NMI and Faults.
21:20
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
156
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
Description
19:12
VECPEND
RO
0x00
Interrupt Pending Vector Number
This field contains the exception number of the highest priority pending
enabled exception. The value indicated by this field includes the effect
of the BASEPRI and FAULTMASK registers, but not any effect of the
PRIMASK register.
Value
Description
0x00
No exceptions are pending
0x01
Reserved
0x02
NMI
0x03
Hard fault
0x04
Memory management fault
0x05
Bus fault
0x06
Usage fault
0x07-0x0A Reserved
11
RETBASE
RO
0
0x0B
SVCall
0x0C
Reserved for Debug
0x0D
Reserved
0x0E
PendSV
0x0F
SysTick
0x10
Interrupt Vector 0
0x11
Interrupt Vector 1
...
...
0x9A
Interrupt Vector 138
Return to Base
Value Description
0
There are preempted active exceptions to execute.
1
There are no active exceptions, or the currently executing
exception is the only active exception.
This bit provides status for all interrupts excluding NMI and Faults. This
bit only has meaning if the processor is currently executing an ISR (the
Interrupt Program Status (IPSR) register is non-zero).
10:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:0
VECACT
RO
0x00
Interrupt Pending Vector Number
This field contains the active exception number. The exception numbers
can be found in the description for the VECPEND field. If this field is clear,
the processor is in Thread mode. This field contains the same value as
the ISRNUM field in the IPSR register.
Subtract 16 from this value to obtain the IRQ number required to index
into the Interrupt Set Enable (ENn), Interrupt Clear Enable (DISn),
Interrupt Set Pending (PENDn), Interrupt Clear Pending (UNPENDn),
and Interrupt Priority (PRIn) registers (see page 76).
June 12, 2014
157
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 68: Vector Table Offset (VTABLE), offset 0xD08
Note:
This register can only be accessed from privileged mode.
The VTABLE register indicates the offset of the vector table base address from memory address
0x0000.0000.
Vector Table Offset (VTABLE)
Base 0xE000.E000
Offset 0xD08
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
OFFSET
Type
Reset
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
OFFSET
Type
Reset
RW
0
RW
0
RW
0
RW
0
reserved
RW
0
RW
0
RO
0
Bit/Field
Name
Type
Reset
31:10
OFFSET
RW
0x000.00
RO
0
RO
0
RO
0
RO
0
Description
Vector Table Offset
When configuring the OFFSET field, the offset must be aligned to the
number of exception entries in the vector table. Because there are 138
interrupts, the offset must be aligned on a 1024-byte boundary.
9:0
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
158
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 69: Application Interrupt and Reset Control (APINT), offset 0xD0C
Note:
This register can only be accessed from privileged mode.
The APINT register provides priority grouping control for the exception model, endian status for
data accesses, and reset control of the system. To write to this register, 0x05FA must be written to
the VECTKEY field, otherwise the write is ignored.
The PRIGROUP field indicates the position of the binary point that splits the INTx fields in the
Interrupt Priority (PRIx) registers into separate group priority and subpriority fields. Table
3-9 on page 159 shows how the PRIGROUP value controls this split. The bit numbers in the Group
Priority Field and Subpriority Field columns in the table refer to the bits in the INTA field. For the
INTB field, the corresponding bits are 15:13; for INTC, 23:21; and for INTD, 31:29.
Note:
Determining preemption of an exception uses only the group priority field.
Table 3-9. Interrupt Priority Levels
a
PRIGROUP Bit Field
Binary Point
Group Priority Field Subpriority Field
Group
Priorities
Subpriorities
0x0 - 0x4
bxxx.
[7:5]
None
8
1
0x5
bxx.y
[7:6]
[5]
4
2
0x6
bx.yy
[7]
[6:5]
2
4
0x7
b.yyy
None
[7:5]
1
8
a. INTx field showing the binary point. An x denotes a group priority field bit, and a y denotes a subpriority field bit.
Application Interrupt and Reset Control (APINT)
Base 0xE000.E000
Offset 0xD0C
Type RW, reset 0xFA05.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
1
RW
0
RW
1
5
4
3
2
1
0
VECTKEY
Type
Reset
RW
1
RW
1
RW
1
RW
1
RW
1
RW
0
15
14
13
12
11
10
reserved
ENDIANESS
Type
Reset
RO
0
RO
0
RO
0
RO
0
RW
1
RW
0
RW
0
RW
0
9
8
7
6
PRIGROUP
RO
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
31:16
VECTKEY
RW
0xFA05
reserved
RW
0
RO
0
RO
0
RO
0
SYSRESREQ VECTCLRACT VECTRESET
RO
0
RO
0
WO
0
WO
0
WO
0
Description
Register Key
This field is used to guard against accidental writes to this register.
0x05FA must be written to this field in order to change the bits in this
register. On a read, 0xFA05 is returned.
15
ENDIANESS
RO
0
Data Endianess
The Tiva™ C Series implementation uses only little-endian mode so
this is cleared to 0.
14:11
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
159
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
10:8
PRIGROUP
RW
0x0
Description
Interrupt Priority Grouping
This field determines the split of group priority from subpriority (see
Table 3-9 on page 159 for more information).
7:3
reserved
RO
0x0
2
SYSRESREQ
WO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
System Reset Request
Value Description
0
No effect.
1
Resets the core and all on-chip peripherals except the Debug
interface.
This bit is automatically cleared during the reset of the core and reads
as 0.
1
VECTCLRACT
WO
0
Clear Active NMI / Fault
This bit is reserved for Debug use and reads as 0. This bit must be
written as a 0, otherwise behavior is unpredictable.
0
VECTRESET
WO
0
System Reset
This bit is reserved for Debug use and reads as 0. This bit must be
written as a 0, otherwise behavior is unpredictable.
160
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 70: System Control (SYSCTRL), offset 0xD10
Note:
This register can only be accessed from privileged mode.
The SYSCTRL register controls features of entry to and exit from low-power state.
System Control (SYSCTRL)
Base 0xE000.E000
Offset 0xD10
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
10
9
8
7
6
5
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:5
reserved
RO
0x0000.00
4
SEVONPEND
RW
0
RO
0
RO
0
RO
0
RO
0
4
3
SEVONPEND
reserved
RW
0
RO
0
SLEEPDEEP SLEEPEXIT
RW
0
RW
0
0
reserved
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Wake Up on Pending
Value Description
0
Only enabled interrupts or events can wake up the processor;
disabled interrupts are excluded.
1
Enabled events and all interrupts, including disabled interrupts,
can wake up the processor.
When an event or interrupt enters the pending state, the event signal
wakes up the processor from WFE. If the processor is not waiting for an
event, the event is registered and affects the next WFE.
The processor also wakes up on execution of a SEV instruction or an
external event.
3
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
2
SLEEPDEEP
RW
0
Deep Sleep Enable
Value Description
0
Use Sleep mode as the low power mode.
1
Use Deep-sleep mode as the low power mode.
June 12, 2014
161
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
1
SLEEPEXIT
RW
0
Description
Sleep on ISR Exit
Value Description
0
When returning from Handler mode to Thread mode, do not
sleep when returning to Thread mode.
1
When returning from Handler mode to Thread mode, enter sleep
or deep sleep on return from an ISR.
Setting this bit enables an interrupt-driven application to avoid returning
to an empty main application.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
162
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 71: Configuration and Control (CFGCTRL), offset 0xD14
Note:
This register can only be accessed from privileged mode.
The CFGCTRL register controls entry to Thread mode and enables: the handlers for NMI, hard fault
and faults escalated by the FAULTMASK register to ignore bus faults; trapping of divide by zero
and unaligned accesses; and access to the SWTRIG register by unprivileged software (see page 151).
Configuration and Control (CFGCTRL)
Base 0xE000.E000
Offset 0xD14
Type RW, reset 0x0000.0200
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
6
5
2
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
reserved
STKALIGN BFHFNMIGN
RO
0
RO
0
RW
1
Bit/Field
Name
Type
Reset
31:10
reserved
RO
0x0000.00
9
STKALIGN
RW
1
RW
0
RO
0
RO
0
RO
0
4
3
DIV0
UNALIGNED
RW
0
RW
0
reserved MAINPEND BASETHR
RO
0
RW
0
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Stack Alignment on Exception Entry
Value Description
0
The stack is 4-byte aligned.
1
The stack is 8-byte aligned.
On exception entry, the processor uses bit 9 of the stacked PSR to
indicate the stack alignment. On return from the exception, it uses this
stacked bit to restore the correct stack alignment.
8
BFHFNMIGN
RW
0
Ignore Bus Fault in NMI and Fault
This bit enables handlers with priority -1 or -2 to ignore data bus faults
caused by load and store instructions. The setting of this bit applies to
the hard fault, NMI, and FAULTMASK escalated handlers.
Value Description
0
Data bus faults caused by load and store instructions cause a
lock-up.
1
Handlers running at priority -1 and -2 ignore data bus faults
caused by load and store instructions.
Set this bit only when the handler and its data are in absolutely safe
memory. The normal use of this bit is to probe system devices and
bridges to detect control path problems and fix them.
7:5
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
163
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
4
DIV0
RW
0
Description
Trap on Divide by 0
This bit enables faulting or halting when the processor executes an
SDIV or UDIV instruction with a divisor of 0.
Value Description
3
UNALIGNED
RW
0
0
Do not trap on divide by 0. A divide by zero returns a quotient
of 0.
1
Trap on divide by 0.
Trap on Unaligned Access
Value Description
0
Do not trap on unaligned halfword and word accesses.
1
Trap on unaligned halfword and word accesses. An unaligned
access generates a usage fault.
Unaligned LDM, STM, LDRD, and STRD instructions always fault
regardless of whether UNALIGNED is set.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
MAINPEND
RW
0
Allow Main Interrupt Trigger
Value Description
0
BASETHR
RW
0
0
Disables unprivileged software access to the SWTRIG register.
1
Enables unprivileged software access to the SWTRIG register
(see page 151).
Thread State Control
Value Description
0
The processor can enter Thread mode only when no exception
is active.
1
The processor can enter Thread mode from any level under the
control of an EXC_RETURN value (see “Exception
Return” on page 105 for more information).
164
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 72: System Handler Priority 1 (SYSPRI1), offset 0xD18
Note:
This register can only be accessed from privileged mode.
The SYSPRI1 register configures the priority level, 0 to 7 of the usage fault, bus fault, and memory
management fault exception handlers. This register is byte-accessible.
System Handler Priority 1 (SYSPRI1)
Base 0xE000.E000
Offset 0xD18
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
reserved
Type
Reset
RO
0
15
RO
0
RO
0
RO
0
RO
0
14
13
12
11
BUS
Type
Reset
RW
0
RW
0
RO
0
RO
0
RO
0
RW
0
10
9
8
7
reserved
RW
0
RO
0
22
21
20
19
USAGE
RO
0
RO
0
RW
0
RW
0
RO
0
RO
0
6
5
4
3
MEM
RO
0
RO
0
RW
0
RW
0
18
17
16
RO
0
RO
0
RO
0
2
1
0
RO
0
RO
0
reserved
reserved
RW
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
USAGE
RW
0x0
Usage Fault Priority
This field configures the priority level of the usage fault. Configurable
priority values are in the range 0-7, with lower values having higher
priority.
20:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:13
BUS
RW
0x0
Bus Fault Priority
This field configures the priority level of the bus fault. Configurable priority
values are in the range 0-7, with lower values having higher priority.
12:8
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7:5
MEM
RW
0x0
Memory Management Fault Priority
This field configures the priority level of the memory management fault.
Configurable priority values are in the range 0-7, with lower values
having higher priority.
4:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
165
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 73: System Handler Priority 2 (SYSPRI2), offset 0xD1C
Note:
This register can only be accessed from privileged mode.
The SYSPRI2 register configures the priority level, 0 to 7 of the SVCall handler. This register is
byte-accessible.
System Handler Priority 2 (SYSPRI2)
Base 0xE000.E000
Offset 0xD1C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
SVC
Type
Reset
22
21
20
19
18
17
16
reserved
RW
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
SVC
RW
0x0
RO
0
Description
SVCall Priority
This field configures the priority level of SVCall. Configurable priority
values are in the range 0-7, with lower values having higher priority.
28:0
reserved
RO
0x000.0000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
166
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 74: System Handler Priority 3 (SYSPRI3), offset 0xD20
Note:
This register can only be accessed from privileged mode.
The SYSPRI3 register configures the priority level, 0 to 7 of the SysTick exception and PendSV
handlers. This register is byte-accessible.
System Handler Priority 3 (SYSPRI3)
Base 0xE000.E000
Offset 0xD20
Type RW, reset 0x0000.0000
31
30
29
28
27
TICK
Type
Reset
26
25
24
23
reserved
RW
0
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
15
14
13
12
11
10
9
8
7
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
22
21
20
19
PENDSV
RW
0
RW
0
RO
0
RO
0
6
5
4
3
DEBUG
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
TICK
RW
0x0
RO
0
RW
0
RW
0
18
17
16
RO
0
RO
0
RO
0
2
1
0
RO
0
RO
0
reserved
reserved
RW
0
RO
0
RO
0
RO
0
Description
SysTick Exception Priority
This field configures the priority level of the SysTick exception.
Configurable priority values are in the range 0-7, with lower values
having higher priority.
28:24
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:21
PENDSV
RW
0x0
PendSV Priority
This field configures the priority level of PendSV. Configurable priority
values are in the range 0-7, with lower values having higher priority.
20:8
reserved
RO
0x000
7:5
DEBUG
RW
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Debug Priority
This field configures the priority level of Debug. Configurable priority
values are in the range 0-7, with lower values having higher priority.
4:0
reserved
RO
0x0.0000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
167
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 75: System Handler Control and State (SYSHNDCTRL), offset 0xD24
Note:
This register can only be accessed from privileged mode.
The SYSHNDCTRL register enables the system handlers, and indicates the pending status of the
usage fault, bus fault, memory management fault, and SVC exceptions as well as the active status
of the system handlers.
If a system handler is disabled and the corresponding fault occurs, the processor treats the fault as
a hard fault.
This register can be modified to change the pending or active status of system exceptions. An OS
kernel can write to the active bits to perform a context switch that changes the current exception
type.
Caution – Software that changes the value of an active bit in this register without correct adjustment
to the stacked content can cause the processor to generate a fault exception. Ensure software that writes
to this register retains and subsequently restores the current active status.
If the value of a bit in this register must be modified after enabling the system handlers, a
read-modify-write procedure must be used to ensure that only the required bit is modified.
System Handler Control and State (SYSHNDCTRL)
Base 0xE000.E000
Offset 0xD24
Type RW, reset 0x0000.0000
31
30
29
28
27
26
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
SVC
BUSP
MEMP
USAGEP
RW
0
RW
0
RW
0
RW
0
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
USAGE
BUS
MEM
RW
0
RW
0
RW
0
10
9
8
7
6
5
4
3
2
1
0
TICK
PNDSV
reserved
MON
SVCA
RW
0
RW
0
RO
0
RW
0
RW
0
USGA
reserved
BUSA
MEMA
RW
0
RO
0
RW
0
RW
0
reserved
Type
Reset
Type
Reset
reserved
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:19
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
18
USAGE
RW
0
Usage Fault Enable
Value Description
17
BUS
RW
0
0
Disables the usage fault exception.
1
Enables the usage fault exception.
Bus Fault Enable
Value Description
0
Disables the bus fault exception.
1
Enables the bus fault exception.
168
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
16
MEM
RW
0
Description
Memory Management Fault Enable
Value Description
15
SVC
RW
0
0
Disables the memory management fault exception.
1
Enables the memory management fault exception.
SVC Call Pending
Value Description
0
An SVC call exception is not pending.
1
An SVC call exception is pending.
This bit can be modified to change the pending status of the SVC call
exception.
14
BUSP
RW
0
Bus Fault Pending
Value Description
0
A bus fault exception is not pending.
1
A bus fault exception is pending.
This bit can be modified to change the pending status of the bus fault
exception.
13
MEMP
RW
0
Memory Management Fault Pending
Value Description
0
A memory management fault exception is not pending.
1
A memory management fault exception is pending.
This bit can be modified to change the pending status of the memory
management fault exception.
12
USAGEP
RW
0
Usage Fault Pending
Value Description
0
A usage fault exception is not pending.
1
A usage fault exception is pending.
This bit can be modified to change the pending status of the usage fault
exception.
11
TICK
RW
0
SysTick Exception Active
Value Description
0
A SysTick exception is not active.
1
A SysTick exception is active.
This bit can be modified to change the active status of the SysTick
exception, however, see the Caution above before setting this bit.
June 12, 2014
169
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
10
PNDSV
RW
0
Description
PendSV Exception Active
Value Description
0
A PendSV exception is not active.
1
A PendSV exception is active.
This bit can be modified to change the active status of the PendSV
exception, however, see the Caution above before setting this bit.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
8
MON
RW
0
Debug Monitor Active
Value Description
7
SVCA
RW
0
0
The Debug monitor is not active.
1
The Debug monitor is active.
SVC Call Active
Value Description
0
SVC call is not active.
1
SVC call is active.
This bit can be modified to change the active status of the SVC call
exception, however, see the Caution above before setting this bit.
6:4
reserved
RO
0x0
3
USGA
RW
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Usage Fault Active
Value Description
0
Usage fault is not active.
1
Usage fault is active.
This bit can be modified to change the active status of the usage fault
exception, however, see the Caution above before setting this bit.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
BUSA
RW
0
Bus Fault Active
Value Description
0
Bus fault is not active.
1
Bus fault is active.
This bit can be modified to change the active status of the bus fault
exception, however, see the Caution above before setting this bit.
170
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
MEMA
RW
0
Description
Memory Management Fault Active
Value Description
0
Memory management fault is not active.
1
Memory management fault is active.
This bit can be modified to change the active status of the memory
management fault exception, however, see the Caution above before
setting this bit.
June 12, 2014
171
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 76: Configurable Fault Status (FAULTSTAT), offset 0xD28
Note:
This register can only be accessed from privileged mode.
The FAULTSTAT register indicates the cause of a memory management fault, bus fault, or usage
fault. Each of these functions is assigned to a subregister as follows:
■ Usage Fault Status (UFAULTSTAT), bits 31:16
■ Bus Fault Status (BFAULTSTAT), bits 15:8
■ Memory Management Fault Status (MFAULTSTAT), bits 7:0
FAULTSTAT is byte accessible. FAULTSTAT or its subregisters can be accessed as follows:
■
■
■
■
■
The complete FAULTSTAT register, with a word access to offset 0xD28
The MFAULTSTAT, with a byte access to offset 0xD28
The MFAULTSTAT and BFAULTSTAT, with a halfword access to offset 0xD28
The BFAULTSTAT, with a byte access to offset 0xD29
The UFAULTSTAT, with a halfword access to offset 0xD2A
Bits are cleared by writing a 1 to them.
In a fault handler, the true faulting address can be determined by:
1. Read and save the Memory Management Fault Address (MMADDR) or Bus Fault Address
(FAULTADDR) value.
2. Read the MMARV bit in MFAULTSTAT, or the BFARV bit in BFAULTSTAT to determine if the
MMADDR or FAULTADDR contents are valid.
Software must follow this sequence because another higher priority exception might change the
MMADDR or FAULTADDR value. For example, if a higher priority handler preempts the current
fault handler, the other fault might change the MMADDR or FAULTADDR value.
Configurable Fault Status (FAULTSTAT)
Base 0xE000.E000
Offset 0xD28
Type RW1C, reset 0x0000.0000
31
30
29
28
27
26
reserved
Type
Reset
RO
0
15
BFARV
Type
Reset
RW1C
0
RO
0
RO
0
RO
0
14
13
12
reserved BLSPERR BSTKE
RO
0
RW1C
0
RW1C
0
RO
0
RO
0
25
24
DIV0
UNALIGN
RW1C
0
RW1C
0
23
22
21
20
reserved
RO
0
11
10
9
8
7
BUSTKE
IMPRE
PRECISE
IBUS
MMARV
RW1C
0
RW1C
0
RW1C
0
RW1C
0
RW1C
0
RO
0
RO
0
RO
0
6
5
4
reserved MLSPERR MSTKE
RO
0
RW1C
0
RW1C
0
19
18
17
16
NOCP
INVPC
INVSTAT
UNDEF
RW1C
0
RW1C
0
RW1C
0
RW1C
0
3
2
MUSTKE reserved
RW1C
0
RO
0
1
0
DERR
IERR
RW1C
0
RW1C
0
Bit/Field
Name
Type
Reset
Description
31:26
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
172
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
25
DIV0
RW1C
0
Description
Divide-by-Zero Usage Fault
Value Description
0
No divide-by-zero fault has occurred, or divide-by-zero trapping
is not enabled.
1
The processor has executed an SDIV or UDIV instruction with
a divisor of 0.
When this bit is set, the PC value stacked for the exception return points
to the instruction that performed the divide by zero.
Trapping on divide-by-zero is enabled by setting the DIV0 bit in the
Configuration and Control (CFGCTRL) register (see page 163).
This bit is cleared by writing a 1 to it.
24
UNALIGN
RW1C
0
Unaligned Access Usage Fault
Value Description
0
No unaligned access fault has occurred, or unaligned access
trapping is not enabled.
1
The processor has made an unaligned memory access.
Unaligned LDM, STM, LDRD, and STRD instructions always fault
regardless of the configuration of this bit.
Trapping on unaligned access is enabled by setting the UNALIGNED bit
in the CFGCTRL register (see page 163).
This bit is cleared by writing a 1 to it.
23:20
reserved
RO
0x00
19
NOCP
RW1C
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
No Coprocessor Usage Fault
Value Description
0
A usage fault has not been caused by attempting to access a
coprocessor.
1
The processor has attempted to access a coprocessor.
This bit is cleared by writing a 1 to it.
18
INVPC
RW1C
0
Invalid PC Load Usage Fault
Value Description
0
A usage fault has not been caused by attempting to load an
invalid PC value.
1
The processor has attempted an illegal load of EXC_RETURN
to the PC as a result of an invalid context or an invalid
EXC_RETURN value.
When this bit is set, the PC value stacked for the exception return points
to the instruction that tried to perform the illegal load of the PC.
This bit is cleared by writing a 1 to it.
June 12, 2014
173
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
17
INVSTAT
RW1C
0
Description
Invalid State Usage Fault
Value Description
0
A usage fault has not been caused by an invalid state.
1
The processor has attempted to execute an instruction that
makes illegal use of the EPSR register.
When this bit is set, the PC value stacked for the exception return points
to the instruction that attempted the illegal use of the Execution
Program Status Register (EPSR) register.
This bit is not set if an undefined instruction uses the EPSR register.
This bit is cleared by writing a 1 to it.
16
UNDEF
RW1C
0
Undefined Instruction Usage Fault
Value Description
0
A usage fault has not been caused by an undefined instruction.
1
The processor has attempted to execute an undefined
instruction.
When this bit is set, the PC value stacked for the exception return points
to the undefined instruction.
An undefined instruction is an instruction that the processor cannot
decode.
This bit is cleared by writing a 1 to it.
15
BFARV
RW1C
0
Bus Fault Address Register Valid
Value Description
0
The value in the Bus Fault Address (FAULTADDR) register
is not a valid fault address.
1
The FAULTADDR register is holding a valid fault address.
This bit is set after a bus fault, where the address is known. Other faults
can clear this bit, such as a memory management fault occurring later.
If a bus fault occurs and is escalated to a hard fault because of priority,
the hard fault handler must clear this bit. This action prevents problems
if returning to a stacked active bus fault handler whose FAULTADDR
register value has been overwritten.
This bit is cleared by writing a 1 to it.
14
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
13
BLSPERR
RW1C
0
Bus Fault on Floating-Point Lazy State Preservation
Value Description
0
No bus fault has occurred during floating-point lazy state
preservation.
1
A bus fault has occurred during floating-point lazy state
preservation.
This bit is cleared by writing a 1 to it.
174
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
12
BSTKE
RW1C
0
Description
Stack Bus Fault
Value Description
0
No bus fault has occurred on stacking for exception entry.
1
Stacking for an exception entry has caused one or more bus
faults.
When this bit is set, the SP is still adjusted but the values in the context
area on the stack might be incorrect. A fault address is not written to
the FAULTADDR register.
This bit is cleared by writing a 1 to it.
11
BUSTKE
RW1C
0
Unstack Bus Fault
Value Description
0
No bus fault has occurred on unstacking for a return from
exception.
1
Unstacking for a return from exception has caused one or more
bus faults.
This fault is chained to the handler. Thus, when this bit is set, the original
return stack is still present. The SP is not adjusted from the failing return,
a new save is not performed, and a fault address is not written to the
FAULTADDR register.
This bit is cleared by writing a 1 to it.
10
IMPRE
RW1C
0
Imprecise Data Bus Error
Value Description
0
An imprecise data bus error has not occurred.
1
A data bus error has occurred, but the return address in the
stack frame is not related to the instruction that caused the error.
When this bit is set, a fault address is not written to the FAULTADDR
register.
This fault is asynchronous. Therefore, if the fault is detected when the
priority of the current process is higher than the bus fault priority, the
bus fault becomes pending and becomes active only when the processor
returns from all higher-priority processes. If a precise fault occurs before
the processor enters the handler for the imprecise bus fault, the handler
detects that both the IMPRE bit is set and one of the precise fault status
bits is set.
This bit is cleared by writing a 1 to it.
9
PRECISE
RW1C
0
Precise Data Bus Error
Value Description
0
A precise data bus error has not occurred.
1
A data bus error has occurred, and the PC value stacked for
the exception return points to the instruction that caused the
fault.
When this bit is set, the fault address is written to the FAULTADDR
register.
This bit is cleared by writing a 1 to it.
June 12, 2014
175
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
8
IBUS
RW1C
0
Description
Instruction Bus Error
Value Description
0
An instruction bus error has not occurred.
1
An instruction bus error has occurred.
The processor detects the instruction bus error on prefetching an
instruction, but sets this bit only if it attempts to issue the faulting
instruction.
When this bit is set, a fault address is not written to the FAULTADDR
register.
This bit is cleared by writing a 1 to it.
7
MMARV
RW1C
0
Memory Management Fault Address Register Valid
Value Description
0
The value in the Memory Management Fault Address
(MMADDR) register is not a valid fault address.
1
The MMADDR register is holding a valid fault address.
If a memory management fault occurs and is escalated to a hard fault
because of priority, the hard fault handler must clear this bit. This action
prevents problems if returning to a stacked active memory management
fault handler whose MMADDR register value has been overwritten.
This bit is cleared by writing a 1 to it.
6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
MLSPERR
RW1C
0
Memory Management Fault on Floating-Point Lazy State Preservation
Value Description
0
No memory management fault has occurred during floating-point
lazy state preservation.
1
No memory management fault has occurred during floating-point
lazy state preservation.
This bit is cleared by writing a 1 to it.
4
MSTKE
RW1C
0
Stack Access Violation
Value Description
0
No memory management fault has occurred on stacking for
exception entry.
1
Stacking for an exception entry has caused one or more access
violations.
When this bit is set, the SP is still adjusted but the values in the context
area on the stack might be incorrect. A fault address is not written to
the MMADDR register.
This bit is cleared by writing a 1 to it.
176
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
MUSTKE
RW1C
0
Description
Unstack Access Violation
Value Description
0
No memory management fault has occurred on unstacking for
a return from exception.
1
Unstacking for a return from exception has caused one or more
access violations.
This fault is chained to the handler. Thus, when this bit is set, the original
return stack is still present. The SP is not adjusted from the failing return,
a new save is not performed, and a fault address is not written to the
MMADDR register.
This bit is cleared by writing a 1 to it.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
DERR
RW1C
0
Data Access Violation
Value Description
0
A data access violation has not occurred.
1
The processor attempted a load or store at a location that does
not permit the operation.
When this bit is set, the PC value stacked for the exception return points
to the faulting instruction and the address of the attempted access is
written to the MMADDR register.
This bit is cleared by writing a 1 to it.
0
IERR
RW1C
0
Instruction Access Violation
Value Description
0
An instruction access violation has not occurred.
1
The processor attempted an instruction fetch from a location
that does not permit execution.
This fault occurs on any access to an XN region, even when the MPU
is disabled or not present.
When this bit is set, the PC value stacked for the exception return points
to the faulting instruction and the address of the attempted access is
not written to the MMADDR register.
This bit is cleared by writing a 1 to it.
June 12, 2014
177
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 77: Hard Fault Status (HFAULTSTAT), offset 0xD2C
Note:
This register can only be accessed from privileged mode.
The HFAULTSTAT register gives information about events that activate the hard fault handler.
Bits are cleared by writing a 1 to them.
Hard Fault Status (HFAULTSTAT)
Base 0xE000.E000
Offset 0xD2C
Type RW1C, reset 0x0000.0000
Type
Reset
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
DBG
FORCED
RW1C
0
RW1C
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
VECT
reserved
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW1C
0
RO
0
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31
DBG
RW1C
0
Description
Debug Event
This bit is reserved for Debug use. This bit must be written as a 0,
otherwise behavior is unpredictable.
30
FORCED
RW1C
0
Forced Hard Fault
Value Description
0
No forced hard fault has occurred.
1
A forced hard fault has been generated by escalation of a fault
with configurable priority that cannot be handled, either because
of priority or because it is disabled.
When this bit is set, the hard fault handler must read the other fault
status registers to find the cause of the fault.
This bit is cleared by writing a 1 to it.
29:2
reserved
RO
0x00
1
VECT
RW1C
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Vector Table Read Fault
Value Description
0
No bus fault has occurred on a vector table read.
1
A bus fault occurred on a vector table read.
This error is always handled by the hard fault handler.
When this bit is set, the PC value stacked for the exception return points
to the instruction that was preempted by the exception.
This bit is cleared by writing a 1 to it.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
178
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 78: Memory Management Fault Address (MMADDR), offset 0xD34
Note:
This register can only be accessed from privileged mode.
The MMADDR register contains the address of the location that generated a memory management
fault. When an unaligned access faults, the address in the MMADDR register is the actual address
that faulted. Because a single read or write instruction can be split into multiple aligned accesses,
the fault address can be any address in the range of the requested access size. Bits in the Memory
Management Fault Status (MFAULTSTAT) register indicate the cause of the fault and whether
the value in the MMADDR register is valid (see page 172).
Memory Management Fault Address (MMADDR)
Base 0xE000.E000
Offset 0xD34
Type RW, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
7
6
5
4
3
2
1
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
ADDR
Type
Reset
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
15
14
13
12
11
10
9
8
ADDR
Type
Reset
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
Bit/Field
Name
Type
Reset
31:0
ADDR
RW
-
RW
-
Description
Fault Address
When the MMARV bit of MFAULTSTAT is set, this field holds the address
of the location that generated the memory management fault.
June 12, 2014
179
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 79: Bus Fault Address (FAULTADDR), offset 0xD38
Note:
This register can only be accessed from privileged mode.
The FAULTADDR register contains the address of the location that generated a bus fault. When
an unaligned access faults, the address in the FAULTADDR register is the one requested by the
instruction, even if it is not the address of the fault. Bits in the Bus Fault Status (BFAULTSTAT)
register indicate the cause of the fault and whether the value in the FAULTADDR register is valid
(see page 172).
Bus Fault Address (FAULTADDR)
Base 0xE000.E000
Offset 0xD38
Type RW, reset 31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
7
6
5
4
3
2
1
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
ADDR
Type
Reset
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
15
14
13
12
11
10
9
8
ADDR
Type
Reset
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
Bit/Field
Name
Type
Reset
31:0
ADDR
RW
-
RW
-
Description
Fault Address
When the FAULTADDRV bit of BFAULTSTAT is set, this field holds the
address of the location that generated the bus fault.
3.6
Memory Protection Unit (MPU) Register Descriptions
This section lists and describes the Memory Protection Unit (MPU) registers, in numerical order by
address offset.
The MPU registers can only be accessed from privileged mode.
180
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 80: MPU Type (MPUTYPE), offset 0xD90
Note:
This register can only be accessed from privileged mode.
The MPUTYPE register indicates whether the MPU is present, and if so, how many regions it
supports.
MPU Type (MPUTYPE)
Base 0xE000.E000
Offset 0xD90
Type RO, reset 0x0000.0800
31
30
29
28
27
26
25
24
23
22
21
20
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
DREGION
Type
Reset
RO
0
RO
0
RO
0
RO
0
19
18
17
16
RO
0
IREGION
RO
0
RO
0
RO
0
RO
0
4
3
2
1
reserved
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
SEPARATE
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:16
IREGION
RO
0x00
Number of I Regions
This field indicates the number of supported MPU instruction regions.
This field always contains 0x00. The MPU memory map is unified and
is described by the DREGION field.
15:8
DREGION
RO
0x08
Number of D Regions
Value Description
0x08 Indicates there are eight supported MPU data regions.
7:1
reserved
RO
0x00
0
SEPARATE
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Separate or Unified MPU
Value Description
0
Indicates the MPU is unified.
June 12, 2014
181
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 81: MPU Control (MPUCTRL), offset 0xD94
Note:
This register can only be accessed from privileged mode.
The MPUCTRL register enables the MPU, enables the default memory map background region,
and enables use of the MPU when in the hard fault, Non-maskable Interrupt (NMI), and Fault Mask
Register (FAULTMASK) escalated handlers.
When the ENABLE and PRIVDEFEN bits are both set:
■ For privileged accesses, the default memory map is as described in “Memory Model” on page 87.
Any access by privileged software that does not address an enabled memory region behaves
as defined by the default memory map.
■ Any access by unprivileged software that does not address an enabled memory region causes
a memory management fault.
Execute Never (XN) and Strongly Ordered rules always apply to the System Control Space regardless
of the value of the ENABLE bit.
When the ENABLE bit is set, at least one region of the memory map must be enabled for the system
to function unless the PRIVDEFEN bit is set. If the PRIVDEFEN bit is set and no regions are enabled,
then only privileged software can operate.
When the ENABLE bit is clear, the system uses the default memory map, which has the same
memory attributes as if the MPU is not implemented (see Table 2-5 on page 90 for more information).
The default memory map applies to accesses from both privileged and unprivileged software.
When the MPU is enabled, accesses to the System Control Space and vector table are always
permitted. Other areas are accessible based on regions and whether PRIVDEFEN is set.
Unless HFNMIENA is set, the MPU is not enabled when the processor is executing the handler for
an exception with priority –1 or –2. These priorities are only possible when handling a hard fault or
NMI exception or when FAULTMASK is enabled. Setting the HFNMIENA bit enables the MPU when
operating with these two priorities.
MPU Control (MPUCTRL)
Base 0xE000.E000
Offset 0xD94
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
PRIVDEFEN HFNMIENA
RW
0
RW
0
ENABLE
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
182
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
PRIVDEFEN
RW
0
Description
MPU Default Region
This bit enables privileged software access to the default memory map.
Value Description
0
If the MPU is enabled, this bit disables use of the default memory
map. Any memory access to a location not covered by any
enabled region causes a fault.
1
If the MPU is enabled, this bit enables use of the default memory
map as a background region for privileged software accesses.
When this bit is set, the background region acts as if it is region number
-1. Any region that is defined and enabled has priority over this default
map.
If the MPU is disabled, the processor ignores this bit.
1
HFNMIENA
RW
0
MPU Enabled During Faults
This bit controls the operation of the MPU during hard fault, NMI, and
FAULTMASK handlers.
Value Description
0
The MPU is disabled during hard fault, NMI, and FAULTMASK
handlers, regardless of the value of the ENABLE bit.
1
The MPU is enabled during hard fault, NMI, and FAULTMASK
handlers.
When the MPU is disabled and this bit is set, the resulting behavior is
unpredictable.
0
ENABLE
RW
0
MPU Enable
Value Description
0
The MPU is disabled.
1
The MPU is enabled.
When the MPU is disabled and the HFNMIENA bit is set, the resulting
behavior is unpredictable.
June 12, 2014
183
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 82: MPU Region Number (MPUNUMBER), offset 0xD98
Note:
This register can only be accessed from privileged mode.
The MPUNUMBER register selects which memory region is referenced by the MPU Region Base
Address (MPUBASE) and MPU Region Attribute and Size (MPUATTR) registers. Normally, the
required region number should be written to this register before accessing the MPUBASE or the
MPUATTR register. However, the region number can be changed by writing to the MPUBASE
register with the VALID bit set (see page 185). This write updates the value of the REGION field.
MPU Region Number (MPUNUMBER)
Base 0xE000.E000
Offset 0xD98
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
2:0
NUMBER
RW
0x0
NUMBER
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
MPU Region to Access
This field indicates the MPU region referenced by the MPUBASE and
MPUATTR registers. The MPU supports eight memory regions.
184
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 83: MPU Region Base Address (MPUBASE), offset 0xD9C
Register 84: MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4
Register 85: MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC
Register 86: MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4
Note:
This register can only be accessed from privileged mode.
The MPUBASE register defines the base address of the MPU region selected by the MPU Region
Number (MPUNUMBER) register and can update the value of the MPUNUMBER register. To
change the current region number and update the MPUNUMBER register, write the MPUBASE
register with the VALID bit set.
The ADDR field is bits 31:N of the MPUBASE register. Bits (N-1):5 are reserved. The region size,
as specified by the SIZE field in the MPU Region Attribute and Size (MPUATTR) register, defines
the value of N where:
N = Log2(Region size in bytes)
If the region size is configured to 4 GB in the MPUATTR register, there is no valid ADDR field. In
this case, the region occupies the complete memory map, and the base address is 0x0000.0000.
The base address is aligned to the size of the region. For example, a 64-KB region must be aligned
on a multiple of 64 KB, for example, at 0x0001.0000 or 0x0002.0000.
MPU Region Base Address (MPUBASE)
Base 0xE000.E000
Offset 0xD9C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
VALID
reserved
RW
0
RW
0
RW
0
RW
0
RW
0
WO
0
RO
0
ADDR
Type
Reset
ADDR
Type
Reset
RW
0
Bit/Field
Name
Type
Reset
31:5
ADDR
RW
0x0000.000
REGION
RW
0
RW
0
RW
0
Description
Base Address Mask
Bits 31:N in this field contain the region base address. The value of N
depends on the region size, as shown above. The remaining bits (N-1):5
are reserved.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
185
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
4
VALID
WO
0
Description
Region Number Valid
Value Description
0
The MPUNUMBER register is not changed and the processor
updates the base address for the region specified in the
MPUNUMBER register and ignores the value of the REGION
field.
1
The MPUNUMBER register is updated with the value of the
REGION field and the base address is updated for the region
specified in the REGION field.
This bit is always read as 0.
3
reserved
RO
0
2:0
REGION
RW
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Region Number
On a write, contains the value to be written to the MPUNUMBER register.
On a read, returns the current region number in the MPUNUMBER
register.
186
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 87: MPU Region Attribute and Size (MPUATTR), offset 0xDA0
Register 88: MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8
Register 89: MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0
Register 90: MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8
Note:
This register can only be accessed from privileged mode.
The MPUATTR register defines the region size and memory attributes of the MPU region specified
by the MPU Region Number (MPUNUMBER) register and enables that region and any subregions.
The MPUATTR register is accessible using word or halfword accesses with the most-significant
halfword holding the region attributes and the least-significant halfword holds the region size and
the region and subregion enable bits.
The MPU access permission attribute bits, XN, AP, TEX, S, C, and B, control access to the
corresponding memory region. If an access is made to an area of memory without the required
permissions, then the MPU generates a permission fault.
The SIZE field defines the size of the MPU memory region specified by the MPUNUMBER register
as follows:
(Region size in bytes) = 2(SIZE+1)
The smallest permitted region size is 32 bytes, corresponding to a SIZE value of 4. Table
3-10 on page 187 gives example SIZE values with the corresponding region size and value of N in
the MPU Region Base Address (MPUBASE) register.
Table 3-10. Example SIZE Field Values
a
SIZE Encoding
Region Size
Value of N
Note
00100b (0x4)
32 B
5
Minimum permitted size
01001b (0x9)
1 KB
10
-
10011b (0x13)
1 MB
20
-
11101b (0x1D)
1 GB
30
-
11111b (0x1F)
4 GB
No valid ADDR field in MPUBASE; the Maximum possible size
region occupies the complete
memory map.
a. Refers to the N parameter in the MPUBASE register (see page 185).
MPU Region Attribute and Size (MPUATTR)
Base 0xE000.E000
Offset 0xDA0
Type RW, reset 0x0000.0000
31
30
29
28
27
reserved
Type
Reset
26
25
24
23
AP
21
reserved
20
19
18
TEX
17
16
XN
reserved
S
C
B
RO
0
RO
0
RO
0
RW
0
RO
0
RW
0
RW
0
RW
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
SRD
Type
Reset
22
reserved
June 12, 2014
SIZE
RW
0
ENABLE
RW
0
187
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
Description
31:29
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
28
XN
RW
0
Instruction Access Disable
Value Description
0
Instruction fetches are enabled.
1
Instruction fetches are disabled.
27
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
26:24
AP
RW
0
Access Privilege
For information on using this bit field, see Table 3-5 on page 124.
23:22
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
21:19
TEX
RW
0x0
Type Extension Mask
For information on using this bit field, see Table 3-3 on page 123.
18
S
RW
0
Shareable
For information on using this bit, see Table 3-3 on page 123.
17
C
RW
0
Cacheable
For information on using this bit, see Table 3-3 on page 123.
16
B
RW
0
Bufferable
For information on using this bit, see Table 3-3 on page 123.
15:8
SRD
RW
0x00
Subregion Disable Bits
Value Description
0
The corresponding subregion is enabled.
1
The corresponding subregion is disabled.
Region sizes of 128 bytes and less do not support subregions. When
writing the attributes for such a region, configure the SRD field as 0x00.
See the section called “Subregions” on page 123 for more information.
7:6
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5:1
SIZE
RW
0x0
Region Size Mask
The SIZE field defines the size of the MPU memory region specified by
the MPUNUMBER register. Refer to Table 3-10 on page 187 for more
information.
188
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
ENABLE
RW
0
Description
Region Enable
Value Description
3.7
0
The region is disabled.
1
The region is enabled.
Floating-Point Unit (FPU) Register Descriptions
This section lists and describes the Floating-Point Unit (FPU) registers, in numerical order by address
offset.
June 12, 2014
189
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 91: Coprocessor Access Control (CPAC), offset 0xD88
The CPAC register specifies the access privileges for coprocessors.
Coprocessor Access Control (CPAC)
Base 0xE000.E000
Offset 0xD88
Type RW, reset 0x0000.0000
31
30
29
28
RO
0
RO
0
RO
0
RO
0
15
14
13
RO
0
RO
0
RO
0
27
26
25
24
23
22
21
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
12
11
10
9
8
7
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
20
19
18
RW
0
RW
0
RO
0
RO
0
RO
0
RO
0
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
CP11
CP10
17
16
reserved
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:24
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
23:22
CP11
RW
0x00
CP11 Coprocessor Access Privilege
Value Description
0x0
Access Denied
Any attempted access generates a NOCP Usage Fault.
0x1
Privileged Access Only
An unprivileged access generates a NOCP fault.
0x2
Reserved
The result of any access is unpredictable.
0x3
21:20
CP10
RW
0x00
Full Access
CP10 Coprocessor Access Privilege
Value Description
0x0
Access Denied
Any attempted access generates a NOCP Usage Fault.
0x1
Privileged Access Only
An unprivileged access generates a NOCP fault.
0x2
Reserved
The result of any access is unpredictable.
0x3
19:0
reserved
RO
0x00
Full Access
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
190
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 92: Floating-Point Context Control (FPCC), offset 0xF34
The FPCC register sets or returns FPU control data.
Floating-Point Context Control (FPCC)
Base 0xE000.E000
Offset 0xF34
Type RW, reset 0xC000.0000
Type
Reset
31
30
29
28
27
26
25
24
23
ASPEN
LSPEN
RW
1
RW
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
6
5
4
3
2
1
0
BFRDY
MMRDY
HFRDY
USER
LSPACT
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
reserved
Type
Reset
22
RO
0
MONRDY reserved
Bit/Field
Name
Type
Reset
31
ASPEN
RW
1
RW
0
RO
0
THREAD reserved
RW
0
RO
0
Description
Automatic State Preservation Enable
When set, enables the use of the FRACTV bit in the CONTROL register
on execution of a floating-point instruction. This results in automatic
hardware state preservation and restoration, for floating-point context,
on exception entry and exit.
Important:
30
LSPEN
RW
1
Two bits control when FPCA can be enabled: the ASPEN
bit in the Floating-Point Context Control (FPCC)
register and the DISFPCA bit in the Auxiliary Control
(ACTLR) register.
Lazy State Preservation Enable
When set, enables automatic lazy state preservation for floating-point
context.
29:9
reserved
RO
0x00
8
MONRDY
RW
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Monitor Ready
When set, DebugMonitor is enabled and priority permits setting
MON_PEND when the floating-point stack frame was allocated.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
BFRDY
RW
0
Bus Fault Ready
When set, BusFault is enabled and priority permitted setting the BusFault
handler to the pending state when the floating-point stack frame was
allocated.
5
MMRDY
RW
0
Memory Management Fault Ready
When set, MemManage is enabled and priority permitted setting the
MemManage handler to the pending state when the floating-point stack
frame was allocated.
June 12, 2014
191
Texas Instruments-Production Data
Cortex-M4 Peripherals
Bit/Field
Name
Type
Reset
4
HFRDY
RW
0
Description
Hard Fault Ready
When set, priority permitted setting the HardFault handler to the pending
state when the floating-point stack frame was allocated.
3
THREAD
RW
0
Thread Mode
When set, mode was Thread Mode when the floating-point stack frame
was allocated.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
USER
RW
0
User Privilege Level
When set, privilege level was user when the floating-point stack frame
was allocated.
0
LSPACT
RW
0
Lazy State Preservation Active
When set, Lazy State preservation is active. Floating-point stack frame
has been allocated but saving state to it has been deferred.
192
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 93: Floating-Point Context Address (FPCA), offset 0xF38
The FPCA register holds the location of the unpopulated floating-point register space allocated on
an exception stack frame.
Floating-Point Context Address (FPCA)
Base 0xE000.E000
Offset 0xF38
Type RW, reset 31
30
29
28
27
26
25
24
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
15
14
13
12
11
10
9
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
23
22
21
20
19
18
17
16
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
8
7
6
5
4
3
2
1
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
RO
0
ADDRESS
Type
Reset
ADDRESS
Type
Reset
RW
-
Bit/Field
Name
Type
Reset
31:3
ADDRESS
RW
-
reserved
RO
0
RO
0
Description
Address
The location of the unpopulated floating-point register space allocated
on an exception stack frame.
2:0
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
193
Texas Instruments-Production Data
Cortex-M4 Peripherals
Register 94: Floating-Point Default Status Control (FPDSC), offset 0xF3C
The FPDSC register holds the default values for the Floating-Point Status Control (FPSC) register.
Floating-Point Default Status Control (FPDSC)
Base 0xE000.E000
Offset 0xF3C
Type RW, reset 0x0000.0000
31
30
RO
0
RO
0
15
RO
0
29
28
27
26
AHP
DN
FZ
RO
0
RO
0
RO
0
RW
-
RW
-
RW
-
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
25
24
23
22
21
20
19
RW
-
17
16
RW
-
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RMODE
18
reserved
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:27
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
26
AHP
RW
-
AHP Bit Default
This bit holds the default value for the AHP bit in the FPSC register.
25
DN
RW
-
DN Bit Default
This bit holds the default value for the DN bit in the FPSC register.
24
FZ
RW
-
FZ Bit Default
This bit holds the default value for the FZ bit in the FPSC register.
23:22
RMODE
RW
-
RMODE Bit Default
This bit holds the default value for the RMODE bit field in the FPSC
register.
Value Description
21:0
reserved
RO
0x00
0x0
Round to Nearest (RN) mode
0x1
Round towards Plus Infinity (RP) mode
0x2
Round towards Minus Infinity (RM) mode
0x3
Round towards Zero (RZ) mode
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
194
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
4
JTAG Interface
The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and
Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface
for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR)
can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing
information on the components. The JTAG Port also provides a means of accessing and controlling
design-for-test features such as I/O pin observation and control, scan testing, and debugging.
The JTAG port is comprised of four pins: TCK, TMS, TDI, and TDO. Data is transmitted serially into
the controller on TDI and out of the controller on TDO. The interpretation of this data is dependent
on the current state of the TAP controller. For detailed information on the operation of the JTAG
port and TAP controller, please refer to the IEEE Standard 1149.1-Test Access Port and
Boundary-Scan Architecture.
The TM4C123BE6PM JTAG controller works with the ARM JTAG controller built into the Cortex-M4F
core by multiplexing the TDO outputs from both JTAG controllers. ARM JTAG instructions select the
ARM TDO output while JTAG instructions select the TDO output. The multiplexer is controlled by the
JTAG controller, which has comprehensive programming for the ARM, Tiva™ C Series
microcontroller, and unimplemented JTAG instructions.
The TM4C123BE6PM JTAG module has the following features:
■ IEEE 1149.1-1990 compatible Test Access Port (TAP) controller
■ Four-bit Instruction Register (IR) chain for storing JTAG instructions
■ IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, and EXTEST
■ ARM additional instructions: APACC, DPACC and ABORT
■ Integrated ARM Serial Wire Debug (SWD)
– Serial Wire JTAG Debug Port (SWJ-DP)
– Flash Patch and Breakpoint (FPB) unit for implementing breakpoints
– Data Watchpoint and Trace (DWT) unit for implementing watchpoints, trigger resources, and
system profiling
– Instrumentation Trace Macrocell (ITM) for support of printf style debugging
– Embedded Trace Macrocell (ETM) for instruction trace capture
– Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer
See the ARM® Debug Interface V5 Architecture Specification for more information on the ARM
JTAG controller.
June 12, 2014
195
Texas Instruments-Production Data
JTAG Interface
4.1
Block Diagram
Figure 4-1. JTAG Module Block Diagram
TCK
TMS
TAP Controller
TDI
Instruction Register (IR)
BYPASS Data Register
TDO
Boundary Scan Data Register
IDCODE Data Register
ABORT Data Register
DPACC Data Register
APACC Data Register
Cortex-M4F
Debug
Port
4.2
Signal Description
The following table lists the external signals of the JTAG/SWD controller and describes the function
of each. The JTAG/SWD controller signals are alternate functions for some GPIO signals, however
note that the reset state of the pins is for the JTAG/SWD function. The JTAG/SWD controller signals
are under commit protection and require a special process to be configured as GPIOs, see “Commit
Control” on page 643. The column in the table below titled "Pin Mux/Pin Assignment" lists the GPIO
pin placement for the JTAG/SWD controller signals. The AFSEL bit in the GPIO Alternate Function
Select (GPIOAFSEL) register (page 658) is set to choose the JTAG/SWD function. The number in
parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control
(GPIOPCTL) register (page 675) to assign the JTAG/SWD controller signals to the specified GPIO
port pin. For more information on configuring GPIOs, see “General-Purpose Input/Outputs
(GPIOs)” on page 636.
Table 4-1. JTAG_SWD_SWO Signals (64LQFP)
Pin Name
Pin Number Pin Mux / Pin
Assignment
a
Pin Type
Buffer Type
Description
SWCLK
52
PC0 (1)
I
TTL
JTAG/SWD CLK.
SWDIO
51
PC1 (1)
I/O
TTL
JTAG TMS and SWDIO.
SWO
49
PC3 (1)
O
TTL
JTAG TDO and SWO.
TCK
52
PC0 (1)
I
TTL
JTAG/SWD CLK.
TDI
50
PC2 (1)
I
TTL
JTAG TDI.
TDO
49
PC3 (1)
O
TTL
JTAG TDO and SWO.
196
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 4-1. JTAG_SWD_SWO Signals (64LQFP) (continued)
Pin Name
Pin Number Pin Mux / Pin
Assignment
51
TMS
PC1 (1)
a
Pin Type
Buffer Type
I
TTL
Description
JTAG TMS and SWDIO.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.
4.3
Functional Description
A high-level conceptual drawing of the JTAG module is shown in Figure 4-1 on page 196. The JTAG
module is composed of the Test Access Port (TAP) controller and serial shift chains with parallel
update registers. The TAP controller is a simple state machine controlled by the TCK and TMS inputs.
The current state of the TAP controller depends on the sequence of values captured on TMS at the
rising edge of TCK. The TAP controller determines when the serial shift chains capture new data,
shift data from TDI towards TDO, and update the parallel load registers. The current state of the
TAP controller also determines whether the Instruction Register (IR) chain or one of the Data Register
(DR) chains is being accessed.
The serial shift chains with parallel load registers are comprised of a single Instruction Register (IR)
chain and multiple Data Register (DR) chains. The current instruction loaded in the parallel load
register determines which DR chain is captured, shifted, or updated during the sequencing of the
TAP controller.
Some instructions, like EXTEST, operate on data currently in a DR chain and do not capture, shift,
or update any of the chains. Instructions that are not implemented decode to the BYPASS instruction
to ensure that the serial path between TDI and TDO is always connected (see Table 4-3 on page 203
for a list of implemented instructions).
See “JTAG and Boundary Scan” on page 1231 for JTAG timing diagrams.
Note:
4.3.1
Of all the possible reset sources, only Power-On reset (POR) and the assertion of the RST
input have any effect on the JTAG module. The pin configurations are reset by both the
RST input and POR, whereas the internal JTAG logic is only reset with POR. See “Reset
Sources” on page 208 for more information on reset.
JTAG Interface Pins
The JTAG interface consists of four standard pins: TCK, TMS, TDI, and TDO. These pins and their
associated state after a power-on reset or reset caused by the RST input are given in Table 4-2.
Detailed information on each pin follows.
Note:
The following pins are configured as JTAG port pins out of reset. Refer to “General-Purpose
Input/Outputs (GPIOs)” on page 636 for information on how to reprogram the configuration
of these pins.
Table 4-2. JTAG Port Pins State after Power-On Reset or RST assertion
Pin Name
Data Direction
Internal Pull-Up
Internal Pull-Down
Drive Strength
Drive Value
TCK
Input
Enabled
Disabled
N/A
N/A
TMS
Input
Enabled
Disabled
N/A
N/A
TDI
Input
Enabled
Disabled
N/A
N/A
TDO
Output
Enabled
Disabled
2-mA driver
High-Z
June 12, 2014
197
Texas Instruments-Production Data
JTAG Interface
4.3.1.1
Test Clock Input (TCK)
The TCK pin is the clock for the JTAG module. This clock is provided so the test logic can operate
independently of any other system clocks and to ensure that multiple JTAG TAP controllers that
are daisy-chained together can synchronously communicate serial test data between components.
During normal operation, TCK is driven by a free-running clock with a nominal 50% duty cycle. When
necessary, TCK can be stopped at 0 or 1 for extended periods of time. While TCK is stopped at 0
or 1, the state of the TAP controller does not change and data in the JTAG Instruction and Data
Registers is not lost.
By default, the internal pull-up resistor on the TCK pin is enabled after reset, assuring that no clocking
occurs if the pin is not driven from an external source. The internal pull-up and pull-down resistors
can be turned off to save internal power as long as the TCK pin is constantly being driven by an
external source (see page 664 and page 666).
4.3.1.2
Test Mode Select (TMS)
The TMS pin selects the next state of the JTAG TAP controller. TMS is sampled on the rising edge
of TCK. Depending on the current TAP state and the sampled value of TMS, the next state may be
entered. Because the TMS pin is sampled on the rising edge of TCK, the IEEE Standard 1149.1
expects the value on TMS to change on the falling edge of TCK.
Holding TMS high for five consecutive TCK cycles drives the TAP controller state machine to the
Test-Logic-Reset state. When the TAP controller enters the Test-Logic-Reset state, the JTAG
module and associated registers are reset to their default values. This procedure should be performed
to initialize the JTAG controller. The JTAG Test Access Port state machine can be seen in its entirety
in Figure 4-2 on page 199.
By default, the internal pull-up resistor on the TMS pin is enabled after reset. Changes to the pull-up
resistor settings on GPIO Port C should ensure that the internal pull-up resistor remains enabled
on PC1/TMS; otherwise JTAG communication could be lost (see page 664).
4.3.1.3
Test Data Input (TDI)
The TDI pin provides a stream of serial information to the IR chain and the DR chains. TDI is
sampled on the rising edge of TCK and, depending on the current TAP state and the current
instruction, may present this data to the proper shift register chain. Because the TDI pin is sampled
on the rising edge of TCK, the IEEE Standard 1149.1 expects the value on TDI to change on the
falling edge of TCK.
By default, the internal pull-up resistor on the TDI pin is enabled after reset. Changes to the pull-up
resistor settings on GPIO Port C should ensure that the internal pull-up resistor remains enabled
on PC2/TDI; otherwise JTAG communication could be lost (see page 664).
4.3.1.4
Test Data Output (TDO)
The TDO pin provides an output stream of serial information from the IR chain or the DR chains.
The value of TDO depends on the current TAP state, the current instruction, and the data in the
chain being accessed. In order to save power when the JTAG port is not being used, the TDO pin
is placed in an inactive drive state when not actively shifting out data. Because TDO can be connected
to the TDI of another controller in a daisy-chain configuration, the IEEE Standard 1149.1 expects
the value on TDO to change on the falling edge of TCK.
By default, the internal pull-up resistor on the TDO pin is enabled after reset, assuring that the pin
remains at a constant logic level when the JTAG port is not being used. The internal pull-up and
198
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
pull-down resistors can be turned off to save internal power if a High-Z output value is acceptable
during certain TAP controller states (see page 664 and page 666).
4.3.2
JTAG TAP Controller
The JTAG TAP controller state machine is shown in Figure 4-2. The TAP controller state machine
is reset to the Test-Logic-Reset state on the assertion of a Power-On-Reset (POR). In order to reset
the JTAG module after the microcontroller has been powered on, the TMS input must be held HIGH
for five TCK clock cycles, resetting the TAP controller and all associated JTAG chains. Asserting
the correct sequence on the TMS pin allows the JTAG module to shift in new instructions, shift in
data, or idle during extended testing sequences. For detailed information on the function of the TAP
controller and the operations that occur in each state, please refer to IEEE Standard 1149.1.
Figure 4-2. Test Access Port State Machine
Test Logic Reset
1
0
Run Test Idle
0
Select DR Scan
1
Select IR Scan
1
0
1
Capture DR
1
Capture IR
0
0
Shift DR
Shift IR
0
1
Exit 1 DR
Exit 1 IR
1
Pause IR
0
1
Exit 2 DR
0
1
0
Exit 2 IR
1
1
Update DR
4.3.3
1
0
Pause DR
1
0
1
0
0
1
0
0
Update IR
1
0
Shift Registers
The Shift Registers consist of a serial shift register chain and a parallel load register. The serial shift
register chain samples specific information during the TAP controller's CAPTURE states and allows
this information to be shifted out on TDO during the TAP controller's SHIFT states. While the sampled
data is being shifted out of the chain on TDO, new data is being shifted into the serial shift register
on TDI. This new data is stored in the parallel load register during the TAP controller's UPDATE
states. Each of the shift registers is discussed in detail in “Register Descriptions” on page 203.
June 12, 2014
199
Texas Instruments-Production Data
JTAG Interface
4.3.4
Operational Considerations
Certain operational parameters must be considered when using the JTAG module. Because the
JTAG pins can be programmed to be GPIOs, board configuration and reset conditions on these
pins must be considered. In addition, because the JTAG module has integrated ARM Serial Wire
Debug, the method for switching between these two operational modes is described below.
4.3.4.1
GPIO Functionality
When the microcontroller is reset with either a POR or RST, the JTAG/SWD port pins default to their
JTAG/SWD configurations. The default configuration includes enabling digital functionality (DEN[3:0]
set in the Port C GPIO Digital Enable (GPIODEN) register), enabling the pull-up resistors (PUE[3:0]
set in the Port C GPIO Pull-Up Select (GPIOPUR) register), disabling the pull-down resistors
(PDE[3:0] cleared in the Port C GPIO Pull-Down Select (GPIOPDR) register) and enabling the
alternate hardware function (AFSEL[3:0] set in the Port C GPIO Alternate Function Select
(GPIOAFSEL) register) on the JTAG/SWD pins. See page 658, page 664, page 666, and page 669.
It is possible for software to configure these pins as GPIOs after reset by clearing AFSEL[3:0] in
the Port C GPIOAFSEL register. If the user does not require the JTAG/SWD port for debugging or
board-level testing, this provides four more GPIOs for use in the design.
Caution – It is possible to create a software sequence that prevents the debugger from connecting to
the TM4C123BE6PM microcontroller. If the program code loaded into flash immediately changes the
JTAG pins to their GPIO functionality, the debugger may not have enough time to connect and halt
the controller before the JTAG pin functionality switches. As a result, the debugger may be locked out
of the part. This issue can be avoided with a software routine that restores JTAG functionality based
on an external or software trigger. In the case that the software routine is not implemented and the
device is locked out of the part, this issue can be solved by using the TM4C123BE6PM Flash Programmer
"Unlock" feature. Please refer to LMFLASHPROGRAMMER on the TI web for more information.
The GPIO commit control registers provide a layer of protection against accidental programming of
critical hardware peripherals. Protection is provided for the GPIO pins that can be used as the four
JTAG/SWD pins and the NMI pin (see “Signal Tables” on page 1200 for pin numbers). Writes to
protected bits of the GPIO Alternate Function Select (GPIOAFSEL) register (see page 658), GPIO
Pull Up Select (GPIOPUR) register (see page 664), GPIO Pull-Down Select (GPIOPDR) register
(see page 666), and GPIO Digital Enable (GPIODEN) register (see page 669) are not committed to
storage unless the GPIO Lock (GPIOLOCK) register (see page 671) has been unlocked and the
appropriate bits of the GPIO Commit (GPIOCR) register (see page 672) have been set.
4.3.4.2
Communication with JTAG/SWD
Because the debug clock and the system clock can be running at different frequencies, care must
be taken to maintain reliable communication with the JTAG/SWD interface. In the Capture-DR state,
the result of the previous transaction, if any, is returned, together with a 3-bit ACK response. Software
should check the ACK response to see if the previous operation has completed before initiating a
new transaction. Alternatively, if the system clock is at least 8 times faster than the debug clock
(TCK or SWCLK), the previous operation has enough time to complete and the ACK bits do not have
to be checked.
4.3.4.3
Recovering a "Locked" Microcontroller
Note:
Performing the sequence below restores the non-volatile registers discussed in “Non-Volatile
Register Programming” on page 520 to their factory default values. The mass erase of the
Flash memory caused by the sequence below occurs prior to the non-volatile registers
being restored.
200
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
In addition, the EEPROM is erased and its wear-leveling counters are returned to factory
default values when performing the sequence below.
If software configures any of the JTAG/SWD pins as GPIO and loses the ability to communicate
with the debugger, there is a debug port unlock sequence that can be used to recover the
microcontroller. Performing a total of ten JTAG-to-SWD and SWD-to-JTAG switch sequences while
holding the microcontroller in reset mass erases the Flash memory. The debug port unlock sequence
is:
1. Assert and hold the RST signal.
2. Apply power to the device.
3. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence on the section called “JTAG-to-SWD
Switching” on page 202.
4. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence on the section called “SWD-to-JTAG
Switching” on page 202.
5. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
6. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
7. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
8. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
9. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
10. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
11. Perform steps 1 and 2 of the JTAG-to-SWD switch sequence.
12. Perform steps 1 and 2 of the SWD-to-JTAG switch sequence.
13. Release the RST signal.
14. Wait 400 ms.
15. Power-cycle the microcontroller.
4.3.4.4
ARM Serial Wire Debug (SWD)
In order to seamlessly integrate the ARM Serial Wire Debug (SWD) functionality, a serial-wire
debugger must be able to connect to the Cortex-M4F core without having to perform, or have any
knowledge of, JTAG cycles. This integration is accomplished with a SWD preamble that is issued
before the SWD session begins.
The switching preamble used to enable the SWD interface of the SWJ-DP module starts with the
TAP controller in the Test-Logic-Reset state. From here, the preamble sequences the TAP controller
through the following states: Run Test Idle, Select DR, Select IR, Test Logic Reset, Test Logic
Reset, Run Test Idle, Run Test Idle, Select DR, Select IR, Test Logic Reset, Test Logic Reset, Run
Test Idle, Run Test Idle, Select DR, Select IR, and Test Logic Reset states.
Stepping through this sequence of the TAP state machine enables the SWD interface and disables
the JTAG interface. For more information on this operation and the SWD interface, see the ARM®
Debug Interface V5 Architecture Specification.
June 12, 2014
201
Texas Instruments-Production Data
JTAG Interface
Because this sequence is a valid series of JTAG operations that could be issued, the ARM JTAG
TAP controller is not fully compliant to the IEEE Standard 1149.1. This instance is the only one
where the ARM JTAG TAP controller does not meet full compliance with the specification. Due to
the low probability of this sequence occurring during normal operation of the TAP controller, it should
not affect normal performance of the JTAG interface.
JTAG-to-SWD Switching
To switch the operating mode of the Debug Access Port (DAP) from JTAG to SWD mode, the
external debug hardware must send the switching preamble to the microcontroller. The 16-bit
TMS/SWDIO command for switching to SWD mode is defined as b1110.0111.1001.1110, transmitted
LSB first. This command can also be represented as 0xE79E when transmitted LSB first. The
complete switch sequence should consist of the following transactions on the TCK/SWCLK and
TMS/SWDIO signals:
1. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that both JTAG and SWD
are in their reset states.
2. Send the 16-bit JTAG-to-SWD switch command, 0xE79E, on TMS/SWDIO.
3. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that if SWJ-DP was already
in SWD mode before sending the switch sequence, the SWD goes into the line reset state.
To verify that the Debug Access Port (DAP) has switched to the Serial Wire Debug (SWD) operating
mode, perform a SWD READID operation. The ID value can be compared against the device's
known ID to verify the switch.
SWD-to-JTAG Switching
To switch the operating mode of the Debug Access Port (DAP) from SWD to JTAG mode, the
external debug hardware must send a switch command to the microcontroller. The 16-bit TMS/SWDIO
command for switching to JTAG mode is defined as b1110.0111.0011.1100, transmitted LSB first.
This command can also be represented as 0xE73C when transmitted LSB first. The complete switch
sequence should consist of the following transactions on the TCK/SWCLK and TMS/SWDIO signals:
1. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that both JTAG and SWD
are in their reset states.
2. Send the 16-bit SWD-to-JTAG switch command, 0xE73C, on TMS/SWDIO.
3. Send at least 50 TCK/SWCLK cycles with TMS/SWDIO High to ensure that if SWJ-DP was already
in JTAG mode before sending the switch sequence, the JTAG goes into the Test Logic Reset
state.
To verify that the Debug Access Port (DAP) has switched to the JTAG operating mode, set the
JTAG Instruction Register (IR) to the IDCODE instruction and shift out the Data Register (DR). The
DR value can be compared against the device's known IDCODE to verify the switch.
4.4
Initialization and Configuration
After a Power-On-Reset or an external reset (RST), the JTAG pins are automatically configured for
JTAG communication. No user-defined initialization or configuration is needed. However, if the user
application changes these pins to their GPIO function, they must be configured back to their JTAG
functionality before JTAG communication can be restored. To return the pins to their JTAG functions,
enable the four JTAG pins (PC[3:0]) for their alternate function using the GPIOAFSEL register.
202
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
In addition to enabling the alternate functions, any other changes to the GPIO pad configurations
on the four JTAG pins (PC[3:0]) should be returned to their default settings.
4.5
Register Descriptions
The registers in the JTAG TAP Controller or Shift Register chains are not memory mapped and are
not accessible through the on-chip Advanced Peripheral Bus (APB). Instead, the registers within
the JTAG controller are all accessed serially through the TAP Controller. These registers include
the Instruction Register and the six Data Registers.
4.5.1
Instruction Register (IR)
The JTAG TAP Instruction Register (IR) is a four-bit serial scan chain connected between the JTAG
TDI and TDO pins with a parallel load register. When the TAP Controller is placed in the correct
states, bits can be shifted into the IR. Once these bits have been shifted into the chain and updated,
they are interpreted as the current instruction. The decode of the IR bits is shown in Table 4-3. A
detailed explanation of each instruction, along with its associated Data Register, follows.
Table 4-3. JTAG Instruction Register Commands
4.5.1.1
IR[3:0]
Instruction
0x0
EXTEST
0x2
SAMPLE / PRELOAD
Description
Drives the values preloaded into the Boundary Scan Chain by the
SAMPLE/PRELOAD instruction onto the pads.
Captures the current I/O values and shifts the sampled values out of the
Boundary Scan Chain while new preload data is shifted in.
0x8
ABORT
Shifts data into the ARM Debug Port Abort Register.
0xA
DPACC
Shifts data into and out of the ARM DP Access Register.
0xB
APACC
Shifts data into and out of the ARM AC Access Register.
0xE
IDCODE
Loads manufacturing information defined by the IEEE Standard 1149.1 into
the IDCODE chain and shifts it out.
0xF
BYPASS
Connects TDI to TDO through a single Shift Register chain.
All Others
Reserved
Defaults to the BYPASS instruction to ensure that TDI is always connected
to TDO.
EXTEST Instruction
The EXTEST instruction is not associated with its own Data Register chain. Instead, the EXTEST
instruction uses the data that has been preloaded into the Boundary Scan Data Register using the
SAMPLE/PRELOAD instruction. When the EXTEST instruction is present in the Instruction Register,
the preloaded data in the Boundary Scan Data Register associated with the outputs and output
enables are used to drive the GPIO pads rather than the signals coming from the core. With tests
that drive known values out of the controller, this instruction can be used to verify connectivity. While
the EXTEST instruction is present in the Instruction Register, the Boundary Scan Data Register can
be accessed to sample and shift out the current data and load new data into the Boundary Scan
Data Register.
4.5.1.2
SAMPLE/PRELOAD Instruction
The SAMPLE/PRELOAD instruction connects the Boundary Scan Data Register chain between
TDI and TDO. This instruction samples the current state of the pad pins for observation and preloads
new test data. Each GPIO pad has an associated input, output, and output enable signal. When the
TAP controller enters the Capture DR state during this instruction, the input, output, and output-enable
signals to each of the GPIO pads are captured. These samples are serially shifted out on TDO while
June 12, 2014
203
Texas Instruments-Production Data
JTAG Interface
the TAP controller is in the Shift DR state and can be used for observation or comparison in various
tests.
While these samples of the inputs, outputs, and output enables are being shifted out of the Boundary
Scan Data Register, new data is being shifted into the Boundary Scan Data Register from TDI.
Once the new data has been shifted into the Boundary Scan Data Register, the data is saved in the
parallel load registers when the TAP controller enters the Update DR state. This update of the
parallel load register preloads data into the Boundary Scan Data Register that is associated with
each input, output, and output enable. This preloaded data can be used with the EXTEST instruction
to drive data into or out of the controller. See “Boundary Scan Data Register” on page 205 for more
information.
4.5.1.3
ABORT Instruction
The ABORT instruction connects the associated ABORT Data Register chain between TDI and
TDO. This instruction provides read and write access to the ABORT Register of the ARM Debug
Access Port (DAP). Shifting the proper data into this Data Register clears various error bits or initiates
a DAP abort of a previous request. See the “ABORT Data Register” on page 206 for more information.
4.5.1.4
DPACC Instruction
The DPACC instruction connects the associated DPACC Data Register chain between TDI and
TDO. This instruction provides read and write access to the DPACC Register of the ARM Debug
Access Port (DAP). Shifting the proper data into this register and reading the data output from this
register allows read and write access to the ARM debug and status registers. See “DPACC Data
Register” on page 206 for more information.
4.5.1.5
APACC Instruction
The APACC instruction connects the associated APACC Data Register chain between TDI and
TDO. This instruction provides read and write access to the APACC Register of the ARM Debug
Access Port (DAP). Shifting the proper data into this register and reading the data output from this
register allows read and write access to internal components and buses through the Debug Port.
See “APACC Data Register” on page 206 for more information.
4.5.1.6
IDCODE Instruction
The IDCODE instruction connects the associated IDCODE Data Register chain between TDI and
TDO. This instruction provides information on the manufacturer, part number, and version of the
ARM core. This information can be used by testing equipment and debuggers to automatically
configure input and output data streams. IDCODE is the default instruction loaded into the JTAG
Instruction Register when a Power-On-Reset (POR) is asserted, or the Test-Logic-Reset state is
entered. See “IDCODE Data Register” on page 205 for more information.
4.5.1.7
BYPASS Instruction
The BYPASS instruction connects the associated BYPASS Data Register chain between TDI and
TDO. This instruction is used to create a minimum length serial path between the TDI and TDO ports.
The BYPASS Data Register is a single-bit shift register. This instruction improves test efficiency by
allowing components that are not needed for a specific test to be bypassed in the JTAG scan chain
by loading them with the BYPASS instruction. See “BYPASS Data Register” on page 205 for more
information.
204
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
4.5.2
Data Registers
The JTAG module contains six Data Registers. These serial Data Register chains include: IDCODE,
BYPASS, Boundary Scan, APACC, DPACC, and ABORT and are discussed in the following sections.
4.5.2.1
IDCODE Data Register
The format for the 32-bit IDCODE Data Register defined by the IEEE Standard 1149.1 is shown in
Figure 4-3. The standard requires that every JTAG-compliant microcontroller implement either the
IDCODE instruction or the BYPASS instruction as the default instruction. The LSB of the IDCODE
Data Register is defined to be a 1 to distinguish it from the BYPASS instruction, which has an LSB
of 0. This definition allows auto-configuration test tools to determine which instruction is the default
instruction.
The major uses of the JTAG port are for manufacturer testing of component assembly and program
development and debug. To facilitate the use of auto-configuration debug tools, the IDCODE
instruction outputs a value of 0x4BA0.0477. This value allows the debuggers to automatically
configure themselves to work correctly with the Cortex-M4F during debug.
Figure 4-3. IDCODE Register Format
31
TDI
4.5.2.2
28 27
12 11
Version
Part Number
1 0
Manufacturer ID
1
TDO
BYPASS Data Register
The format for the 1-bit BYPASS Data Register defined by the IEEE Standard 1149.1 is shown in
Figure 4-4. The standard requires that every JTAG-compliant microcontroller implement either the
BYPASS instruction or the IDCODE instruction as the default instruction. The LSB of the BYPASS
Data Register is defined to be a 0 to distinguish it from the IDCODE instruction, which has an LSB
of 1. This definition allows auto-configuration test tools to determine which instruction is the default
instruction.
Figure 4-4. BYPASS Register Format
0
TDI
4.5.2.3
0
TDO
Boundary Scan Data Register
The format of the Boundary Scan Data Register is shown in Figure 4-5. Each GPIO pin, starting
with a GPIO pin next to the JTAG port pins, is included in the Boundary Scan Data Register. Each
GPIO pin has three associated digital signals that are included in the chain. These signals are input,
output, and output enable, and are arranged in that order as shown in the figure.
When the Boundary Scan Data Register is accessed with the SAMPLE/PRELOAD instruction, the
input, output, and output enable from each digital pad are sampled and then shifted out of the chain
to be verified. The sampling of these values occurs on the rising edge of TCK in the Capture DR
state of the TAP controller. While the sampled data is being shifted out of the Boundary Scan chain
in the Shift DR state of the TAP controller, new data can be preloaded into the chain for use with
the EXTEST instruction. The EXTEST instruction forces data out of the controller.
June 12, 2014
205
Texas Instruments-Production Data
JTAG Interface
Figure 4-5. Boundary Scan Register Format
TDI
I
N
O
U
T
O
E
...
1st GPIO
4.5.2.4
I
N
O
U
T
mth GPIO
O
E
I
N
O
U
T
(m+1)th GPIO
O
E
...
I
N
O
U
T
O
E
TDO
GPIO nth
APACC Data Register
The format for the 35-bit APACC Data Register defined by ARM is described in the ARM® Debug
Interface V5 Architecture Specification.
4.5.2.5
DPACC Data Register
The format for the 35-bit DPACC Data Register defined by ARM is described in the ARM® Debug
Interface V5 Architecture Specification.
4.5.2.6
ABORT Data Register
The format for the 35-bit ABORT Data Register defined by ARM is described in the ARM® Debug
Interface V5 Architecture Specification.
206
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
5
System Control
System control configures the overall operation of the device and provides information about the
device. Configurable features include reset control, NMI operation, power control, clock control, and
low-power modes.
5.1
Signal Description
The following table lists the external signals of the System Control module and describes the function
of each. The NMI signal is the alternate function for two GPIO signals and functions as a GPIO after
reset. The NMI pins are under commit protection and require a special process to be configured as
any alternate function or to subsequently return to the GPIO function, see “Commit
Control” on page 643. The column in the table below titled "Pin Mux/Pin Assignment" lists the GPIO
pin placement for the NMI signal. The AFSEL bit in the GPIO Alternate Function Select
(GPIOAFSEL) register (page 658) should be set to choose the NMI function. The number in
parentheses is the encoding that must be programmed into the PMCn field in the GPIO Port Control
(GPIOPCTL) register (page 675) to assign the NMI signal to the specified GPIO port pin. For more
information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 636. The
remaining signals (with the word "fixed" in the Pin Mux/Pin Assignment column) have a fixed pin
assignment and function.
Table 5-1. System Control & Clocks Signals (64LQFP)
Pin Name
Pin Number Pin Mux / Pin
Assignment
a
Pin Type
Buffer Type
Description
NMI
10
28
PD7 (8)
PF0 (8)
I
TTL
Non-maskable interrupt.
OSC0
40
fixed
I
Analog
Main oscillator crystal input or an external clock
reference input.
OSC1
41
fixed
O
Analog
Main oscillator crystal output. Leave unconnected
when using a single-ended clock source.
RST
38
fixed
I
TTL
System reset input.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.
5.2
Functional Description
The System Control module provides the following capabilities:
■ Device identification, see “Device Identification” on page 207
■ Local control, such as reset (see “Reset Control” on page 208), power (see “Power
Control” on page 213) and clock control (see “Clock Control” on page 214)
■ System control (Run, Sleep, and Deep-Sleep modes), see “System Control” on page 221
5.2.1
Device Identification
Several read-only registers provide software with information on the microcontroller, such as version,
part number, memory sizes, and peripherals present on the device. The Device Identification 0
(DID0) (page 232) and Device Identification 1 (DID1) (page 234) registers provide details about the
device's version, package, temperature range, and so on. The Peripheral Present registers starting
at System Control offset 0x300, such as the Watchdog Timer Peripheral Present (PPWD) register,
provide information on how many of each type of module are included on the device. Finally,
June 12, 2014
207
Texas Instruments-Production Data
System Control
information about the capabilities of the on-chip peripherals are provided at offset 0xFC0 in each
peripheral's register space in the Peripheral Properties registers, such as the GPTM Peripheral
Properties (GPTMPP) register. Previous devices used the Device Capabilities (DC0-DC9) registers
for information about the peripherals and their capabilities. These registers are present on this device
for backward software capability, but provide no information about peripherals that were not available
on older devices.
5.2.2
Reset Control
This section discusses aspects of hardware functions during reset as well as system software
requirements following the reset sequence.
5.2.2.1
Reset Sources
The TM4C123BE6PM microcontroller has six sources of reset:
1. Power-on reset (POR) (see page 209).
2. External reset input pin (RST) assertion (see page 210).
3. A brown-out detection that can be caused by any of the following events: (see page 211).
■ V DD under BOR0. The trigger value is the highest VDD voltage level for BOR0.
■ VDD under BOR1. The trigger value is the highest VDD voltage level for BOR1.
4. Software-initiated reset (with the software reset registers) (see page 212).
5. A watchdog timer reset condition violation (see page 212).
6. MOSC failure (see page 213).
Table 5-2 provides a summary of results of the various reset operations.
Table 5-2. Reset Sources
Core Reset?
JTAG Reset?
On-Chip Peripherals Reset?
Power-On Reset
Reset Source
Yes
Yes
Yes
RST
Yes
Pin Config Only
Yes
Brown-Out Reset
Yes
Pin Config Only
Yes
Software System Request
Reset using the SYSRESREQ
bit in the APINT register.
Yes
Pin Config Only
Yes
Software System Request
Reset using the VECTRESET
bit in the APINT register.
Yes
Pin Config Only
No
Software Peripheral Reset
No
Pin Config Only
Yes
Watchdog Reset
Yes
Pin Config Only
Yes
MOSC Failure Reset
Yes
Pin Config Only
Yes
a
a. Programmable on a module-by-module basis using the Software Reset Control Registers.
After a reset, the Reset Cause (RESC) register is set with the reset cause. The bits in this register
are sticky and maintain their state across multiple reset sequences, except when an internal POR
208
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
is the cause, in which case, all the bits in the RESC register are cleared except for the POR indicator.
A bit in the RESC register can be cleared by writing a 0.
At any reset that resets the core, the user has the opportunity to direct the core to execute the ROM
Boot Loader or the application in Flash memory by using any GPIO signal as configured in the Boot
Configuration (BOOTCFG) register.
At reset, the following sequence is performed:
1. The BOOTCFG register is read. If the EN bit is clear, the ROM Boot Loader is executed.
2. In the ROM Boot Loader, the status of the specified GPIO pin is compared with the specified
polarity. If the status matches the specified polarity, the ROM is mapped to address 0x0000.0000
and execution continues out of the ROM Boot Loader.
3. f then EN bit is set or the status doesn't match the specified polarity, the data at address
0x0000.0004 is read, and if the data at this address is 0xFFFF.FFFF, the ROM is mapped to
address 0x0000.0000 and execution continues out of the ROM Boot Loader.
4. If there is data at address 0x0000.0004 that is not 0xFFFF.FFFF, the stack pointer (SP) is loaded
from Flash memory at address 0x0000.0000 and the program counter (PC) is loaded from
address 0x0000.0004. The user application begins executing.
Note:
If the device fails the initialization phase, it toggles the TDO output pin as an indication the
device is not executing. This feature is provided for debug purposes.
For example, if the BOOTCFG register is written and committed with the value of 0x0000.3C01,
then PB7 is examined at reset to determine if the ROM Boot Loader should be executed. If PB7 is
Low, the core unconditionally begins executing the ROM boot loader. If PB7 is High, then the
application in Flash memory is executed if the reset vector at location 0x0000.0004 is not
0xFFFF.FFFF. Otherwise, the ROM boot loader is executed.
5.2.2.2
Power-On Reset (POR)
Note:
The JTAG controller can only be reset by the power-on reset.
The internal Power-On Reset (POR) circuit monitors the power supply voltage (VDD) and generates
a reset signal to all of the internal logic including JTAG when the power supply ramp reaches a
threshold value (VVDD_POK). The microcontroller must be operating within the specified operating
parameters when the on-chip power-on reset pulse is complete (see “Power and
Brown-Out” on page 1233). For applications that require the use of an external reset signal to hold
the microcontroller in reset longer than the internal POR, the RST input may be used as discussed
in “External RST Pin” on page 210.
The Power-On Reset sequence is as follows:
1. The microcontroller waits for internal POR to go inactive.
2. The internal reset is released and the core loads from memory the initial stack pointer, the initial
program counter, and the first instruction designated by the program counter, and then begins
execution.
The internal POR is only active on the initial power-up of the microcontroller and when the
microcontroller wakes from hibernation. The Power-On Reset timing is shown in “Power and
Brown-Out” on page 1233.
June 12, 2014
209
Texas Instruments-Production Data
System Control
5.2.2.3
External RST Pin
Note:
It is recommended that the trace for the RST signal must be kept as short as possible. Be
sure to place any components connected to the RST signal as close to the microcontroller
as possible.
If the application only uses the internal POR circuit, the RST input must be connected to the power
supply (VDD) through an optional pull-up resistor (0 to 100K Ω) as shown in Figure 5-1 on page 210.
The RST input has filtering which requires a minimum pulse width in order for the reset pulse to be
recognized, see Table 23-11 on page 1238.
Figure 5-1. Basic RST Configuration
VDD
Tiva™
Microcontroller
RPU
RST
RPU = 0 to 100 kΩ
The external reset pin (RST) resets the microcontroller including the core and all the on-chip
peripherals. The external reset sequence is as follows:
1. The external reset pin (RST) is asserted for the duration specified by TMIN and then deasserted
(see “Reset” on page 1238).
2. The internal reset is released and the core loads from memory the initial stack pointer, the initial
program counter, and the first instruction designated by the program counter, and then begins
execution.
To improve noise immunity and/or to delay reset at power up, the RST input may be connected to
an RC network as shown in Figure 5-2 on page 210.
Figure 5-2. External Circuitry to Extend Power-On Reset
VDD
Tiva™
Microcontroller
RPU
RST
C1
RPU = 1 kΩ to 100 kΩ
C1 = 1 nF to 10 µF
210
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
If the application requires the use of an external reset switch, Figure 5-3 on page 211 shows the
proper circuitry to use.
Figure 5-3. Reset Circuit Controlled by Switch
VDD
Tiva™
Microcontroller
RPU
RST
C1
RS
Typical RPU = 10 kΩ
Typical RS = 470 Ω
C1 = 10 nF
The RPU and C1 components define the power-on delay.
The external reset timing is shown in Figure 23-11 on page 1239.
5.2.2.4
Brown-Out Reset (BOR)
The microcontroller provides a brown-out detection circuit that triggers if any of the following occur:
■ VDD under BOR0. The external VDD supply voltage is below the specified VDD BOR0 value. The
trigger value is the highest VDD voltage level for BOR0.
■ VDD under BOR1. The external VDD supply voltage is below the specified VDD BOR1 value. The
trigger value is the highest VDD voltage level for BOR1.
The application can identify that a BOR event caused a reset by reading the Reset Cause (RESC)
register. When a brown-out condition is detected, the default condition is to generate a reset. The
BOR events can also be programmed to generate an interrupt by clearing the BOR0 bit or BOR1 bit
in the Power-On and Brown-Out Reset Control (PBORCTL) register.
The brown-out reset sequence is as follows:
1. When VDD drops below VBORnTH, an internal BOR condition is set. Please refer to “Power and
Brown-Out” on page 1233 for VBORnTH value.
2. If the BOR condition exists, an internal reset is asserted.
3. The internal reset is released and the microcontroller fetches and loads the initial stack pointer,
the initial program counter, the first instruction designated by the program counter, and begins
execution.
The result of a brown-out reset is equivalent to that of an assertion of the external RST input, and
the reset is held active until the proper VDD level is restored. The RESC register can be examined
in the reset interrupt handler to determine if a Brown-Out condition was the cause of the reset, thus
allowing software to determine what actions are required to recover.
June 12, 2014
211
Texas Instruments-Production Data
System Control
The internal Brown-Out Reset timing is shown in “Power and Brown-Out” on page 1233.
5.2.2.5
Software Reset
Software can reset a specific peripheral or generate a reset to the entire microcontroller.
Peripherals can be individually reset by software via peripheral-specific reset registers available
beginning at System Control offset 0x500 (for example the Watchdog Timer Software Reset
(SRWD) register). If the bit position corresponding to a peripheral is set and subsequently cleared,
the peripheral is reset.
The entire microcontroller, including the core, can be reset by software by setting the SYSRESREQ
bit in the Application Interrupt and Reset Control (APINT) register. The software-initiated system
reset sequence is as follows:
1. A software microcontroller reset is initiated by setting the SYSRESREQ bit.
2. An internal reset is asserted.
3. The internal reset is deasserted and the microcontroller loads from memory the initial stack
pointer, the initial program counter, and the first instruction designated by the program counter,
and then begins execution.
The core only can be reset by software by setting the VECTRESET bit in the APINT register. The
software-initiated core reset sequence is as follows:
1. A core reset is initiated by setting the VECTRESET bit.
2. An internal reset is asserted.
3. The internal reset is deasserted and the microcontroller loads from memory the initial stack
pointer, the initial program counter, and the first instruction designated by the program counter,
and then begins execution.
The software-initiated system reset timing is shown in Figure 23-12 on page 1239.
5.2.2.6
Watchdog Timer Reset
The Watchdog Timer module's function is to prevent system hangs. The TM4C123BE6PM
microcontroller has two Watchdog Timer modules in case one watchdog clock source fails. One
watchdog is run off the system clock and the other is run off the Precision Internal Oscillator (PIOSC).
Each module operates in the same manner except that because the PIOSC watchdog timer module
is in a different clock domain, register accesses must have a time delay between them. The watchdog
timer can be configured to generate an interrupt or a non-maskable interrupt to the microcontroller
on its first time-out and to generate a reset on its second time-out.
After the watchdog's first time-out event, the 32-bit watchdog counter is reloaded with the value of
the Watchdog Timer Load (WDTLOAD) register and resumes counting down from that value. If
the timer counts down to zero again before the first time-out interrupt is cleared, and the reset signal
has been enabled, the watchdog timer asserts its reset signal to the microcontroller. The watchdog
timer reset sequence is as follows:
1. The watchdog timer times out for the second time without being serviced.
2. An internal reset is asserted.
212
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
3. The internal reset is released and the microcontroller loads from memory the initial stack pointer,
the initial program counter, and the first instruction designated by the program counter, and
then begins execution.
For more information on the Watchdog Timer module, see “Watchdog Timers” on page 761.
The watchdog reset timing is shown in Figure 23-13 on page 1239.
5.2.3
Non-Maskable Interrupt
The microcontroller has four sources of non-maskable interrupt (NMI):
■ The assertion of the NMI signal
■ A main oscillator verification error
■ The NMISET bit in the Interrupt Control and State (INTCTRL) register in the Cortex™-M4F (see
page 155).
■ The Watchdog module time-out interrupt when the INTTYPE bit in the Watchdog Control
(WDTCTL) register is set (see page 767).
Software must check the cause of the interrupt in order to distinguish among the sources.
5.2.3.1
NMI Pin
The NMI signal is an alternate function for either GPIO port pin PD7 or PF0. The alternate function
must be enabled in the GPIO for the signal to be used as an interrupt, as described in
“General-Purpose Input/Outputs (GPIOs)” on page 636. Note that enabling the NMI alternate function
requires the use of the GPIO lock and commit function just like the GPIO port pins associated with
JTAG/SWD functionality, see page 672. The active sense of the NMI signal is High; asserting the
enabled NMI signal above VIH initiates the NMI interrupt sequence.
5.2.3.2
Main Oscillator Verification Failure
The TM4C123BE6PM microcontroller provides a main oscillator verification circuit that generates
an error condition if the oscillator is running too fast or too slow. If the main oscillator verification
circuit is enabled and a failure occurs, either a power-on reset is generated and control is transferred
to the NMI handler, or an interrupt is generated. The MOSCIM bit in the MOSCCTL register determines
which action occurs. In either case, the system clock source is automatically switched to the PIOSC.
If a MOSC failure reset occurs, the NMI handler is used to address the main oscillator verification
failure because the necessary code can be removed from the general reset handler, speeding up
reset processing. The detection circuit is enabled by setting the CVAL bit in the Main Oscillator
Control (MOSCCTL) register. The main oscillator verification error is indicated in the main oscillator
fail status (MOSCFAIL) bit in the Reset Cause (RESC) register. The main oscillator verification circuit
action is described in more detail in “Main Oscillator Verification Circuit” on page 221.
5.2.4
Power Control
The TM4C123BE6PM microcontroller provides an integrated LDO regulator that is used to provide
power to the majority of the microcontroller's internal logic. Figure 5-4 shows the power architecture.
An external LDO may not be used.
Note:
VDDA must be supplied with a voltage that meets the specification in Table 23-5 on page 1228,
or the microcontroller does not function properly. VDDA is the supply for all of the analog
circuitry on the device, including the clock circuitry.
June 12, 2014
213
Texas Instruments-Production Data
System Control
Figure 5-4. Power Architecture
VDDC
Internal
Logic and PLL
VDDC
GND
GND
LDO Voltage
Regulator
+3.3V
VDD
GND
I/O Buffers
VDD
GND
+3.3V
GNDA
VDDA
Analog Circuits
VDDA
5.2.5
GNDA
Clock Control
System control determines the control of clocks in this part.
5.2.5.1
Fundamental Clock Sources
There are multiple clock sources for use in the microcontroller:
■ Precision Internal Oscillator (PIOSC). The precision internal oscillator is an on-chip clock
source that is the clock source the microcontroller uses during and following POR. It does not
require the use of any external components and provides a 16-MHz clock with ±1% accuracy
with calibration and ±3% accuracy across temperature (see “PIOSC Specifications” on page 1243).
The PIOSC allows for a reduced system cost in applications that require an accurate clock
source. If the main oscillator is required, software must enable the main oscillator following reset
and allow the main oscillator to stabilize before changing the clock reference. If the Hibernation
Module clock source is a 32.768-kHz oscillator, the precision internal oscillator can be trimmed
by software based on a reference clock for increased accuracy. Regardless of whether or not
the PIOSC is the source for the system clock, the PIOSC can be configured to be the source for
the ADC clock as well as the baud clock for the UART and SSI, see “System Control” on page 221.
■ Main Oscillator (MOSC). The main oscillator provides a frequency-accurate clock source by
one of two means: an external single-ended clock source is connected to the OSC0 input pin, or
an external crystal is connected across the OSC0 input and OSC1 output pins. If the PLL is being
214
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
used, the crystal value must be one of the supported frequencies between 5 MHz to 25 MHz
(inclusive). If the PLL is not being used, the crystal may be any one of the supported frequencies
between 4 MHz to 25 MHz. The single-ended clock source range is as specified in Table
23-13 on page 1242. The supported crystals are listed in the XTAL bit field in the RCC register
(see page 247).
■ Low-Frequency Internal Oscillator (LFIOSC). The low-frequency internal oscillator is intended
for use during Deep-Sleep power-saving modes. The frequency can have wide variations; refer
to “Low-Frequency Internal Oscillator (LFIOSC) Specifications” on page 1243 for more details. This
power-savings mode benefits from reduced internal switching and also allows the MOSC to be
powered down. In addition, the PIOSC can be powered down while in Deep-Sleep mode.
■ Hibernation Module Clock Source. The Hibernation module is clocked by a 32.768-kHz oscillator
connected to the XOSC0 pin. The 32.768-kHz oscillator can be used for the system clock, thus
eliminating the need for an additional crystal or oscillator. The Hibernation module clock source
is intended to provide the system with a real-time clock source and may also provide an accurate
source of Deep-Sleep or Hibernate mode power savings.
The internal system clock (SysClk), is derived from any of the above sources plus two others: the
output of the main internal PLL and the precision internal oscillator divided by four (4 MHz ± 1%).
The frequency of the PLL clock reference must be in the range of 5 MHz to 25 MHz (inclusive).
Table 5-3 on page 215 shows how the various clock sources can be used in a system.
Table 5-3. Clock Source Options
5.2.5.2
Clock Source
Drive PLL?
Precision Internal Oscillator
Yes
BYPASS = 0,
OSCSRC = 0x1
Used as SysClk?
Yes
BYPASS = 1, OSCSRC = 0x1
Precision Internal Oscillator divide by
4 (4 MHz ± 1%)
No
-
Yes
BYPASS = 1, OSCSRC = 0x2
Main Oscillator
Yes
BYPASS = 0,
OSCSRC = 0x0
Yes
BYPASS = 1, OSCSRC = 0x0
Low-Frequency Internal Oscillator
(LFIOSC)
No
-
Yes
BYPASS = 1, OSCSRC = 0x3
Hibernation Module 32.768-kHz
Oscillator
No
-
Yes
BYPASS = 1, OSCSRC2 = 0x7
Clock Configuration
The Run-Mode Clock Configuration (RCC) and Run-Mode Clock Configuration 2 (RCC2)
registers provide control for the system clock. The RCC2 register is provided to extend fields that
offer additional encodings over the RCC register. When used, the RCC2 register field values are
used by the logic over the corresponding field in the RCC register. In particular, RCC2 provides for
a larger assortment of clock configuration options. These registers control the following clock
functionality:
■ Source of clocks in sleep and deep-sleep modes
■ System clock derived from PLL or other clock source
■ Enabling/disabling of oscillators and PLL
■ Clock divisors
June 12, 2014
215
Texas Instruments-Production Data
System Control
■ Crystal input selection
Important: Write the RCC register prior to writing the RCC2 register.
When transitioning the system clock configuration to use the MOSC as the fundamental
clock source, the MOSCDIS bit must be set prior to reselecting the MOSC or an undefined
system clock configuration can sporadically occur.
The configuration of the system clock must not be changed while an EEPROM operation
is in process. Software must wait until the WORKING bit in the EEPROM Done Status
(EEDONE) register is clear before making any changes to the system clock.
Figure 5-5 shows the logic for the main clock tree. The peripheral blocks are driven by the system
clock signal and can be individually enabled/disabled. The ADC clock signal can be selected from
the PIOSC, the system clock if the PLL is disabled, or the PLL output divided down to 16 MHz if the
PLL is enabled. The PWM clock signal is a synchronous divide of the system clock to provide the
PWM circuit with more range (set with PWMDIV in RCC).
Note:
If the ADC module is not using the PIOSC as the clock source, the system clock must be
at least 16 MHz.
216
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Figure 5-5. Main Clock Tree
USEPWMDIV a
PWMDW a
PWM Clock
XTALa
PWRDN b
CS f
MOSCDIS a
PLL
(400 MHz)
Main OSC
DIV400 c
BYPASS b,d
USESYSDIV a,d
UART Baud Clock
÷2
IOSCDIS a
System Clock
Precision
Internal OSC
(16 MHz)
÷ SYSDIV
÷4
e
CS f
BYPASS b,d
PWRDN
Internal OSC
(30 kHz)
SSI Baud Clock
÷ 25
Hibernation
OSC
(32.768 kHz)
OSCSRC b,d
CS f
ADC Clock
Note:
a.
b.
c.
d.
e.
f.
Control provided by RCC register bit/field.
Control provided by RCC register bit/field or RCC2 register bit/field, if overridden with RCC2 register bit
USERCC2.
Control provided by RCC2 register bit/field.
Also may be controlled by DSLPCLKCFG when in deep sleep mode.
Control provided by RCC register SYSDIV field, RCC2 register SYSDIV2 field if overridden with USERCC2
bit, or [SYSDIV2,SYSDIV2LSB] if both USERCC2 and DIV400 bits are set.
Control provided by UARTCC, SSICC, and ADCCC register field.
Communication Clock Sources
In addition to the main clock tree described above, the UART, and SSI modules all have a Clock
Control register in the peripheral's register map at offset 0xFC8 that can be used to select the clock
source for the module's baud clock. Users can choose between the system clock, which is the
default source for the baud clock, and the PIOSC. Note that there may be special considerations
when using the PIOSC as the baud clock. For more information, see the Clock Control register
description in the chapter describing the operation of the module.
Using the SYSDIV and SYSDIV2 Fields
In the RCC register, the SYSDIV field specifies which divisor is used to generate the system clock
from either the PLL output or the oscillator source (depending on how the BYPASS bit in this register
is configured). When using the PLL, the VCO frequency of 400 MHz is predivided by 2 before the
divisor is applied. Table 5-4 shows how the SYSDIV encoding affects the system clock frequency,
depending on whether the PLL is used (BYPASS=0) or another clock source is used (BYPASS=1).
June 12, 2014
217
Texas Instruments-Production Data
System Control
The divisor is equivalent to the SYSDIV encoding plus 1. For a list of possible clock sources, see
Table 5-3 on page 215.
Table 5-4. Possible System Clock Frequencies Using the SYSDIV Field
SYSDIV
Divisor
a
Frequency (BYPASS=0) Frequency (BYPASS=1)
TivaWare™ Parameter
0x0
/1
reserved
Clock source frequency/1
SYSCTL_SYSDIV_1
0x1
/2
reserved
Clock source frequency/2
SYSCTL_SYSDIV_2
0x2
/3
66.67 MHz
Clock source frequency/3
SYSCTL_SYSDIV_3
0x3
/4
50 MHz
Clock source frequency/4
SYSCTL_SYSDIV_4
0x4
/5
40 MHz
Clock source frequency/5
SYSCTL_SYSDIV_5
0x5
/6
33.33 MHz
Clock source frequency/6
SYSCTL_SYSDIV_6
0x6
/7
28.57 MHz
Clock source frequency/7
SYSCTL_SYSDIV_7
0x7
/8
25 MHz
Clock source frequency/8
SYSCTL_SYSDIV_8
0x8
/9
22.22 MHz
Clock source frequency/9
SYSCTL_SYSDIV_9
0x9
/10
20 MHz
Clock source frequency/10
SYSCTL_SYSDIV_10
0xA
/11
18.18 MHz
Clock source frequency/11
SYSCTL_SYSDIV_11
0xB
/12
16.67 MHz
Clock source frequency/12
SYSCTL_SYSDIV_12
0xC
/13
15.38 MHz
Clock source frequency/13
SYSCTL_SYSDIV_13
0xD
/14
14.29 MHz
Clock source frequency/14
SYSCTL_SYSDIV_14
0xE
/15
13.33 MHz
Clock source frequency/15
SYSCTL_SYSDIV_15
0xF
/16
12.5 MHz (default)
Clock source frequency/16
SYSCTL_SYSDIV_16
a. This parameter is used in functions such as SysCtlClockSet() in the TivaWare Peripheral Driver Library.
The SYSDIV2 field in the RCC2 register is 2 bits wider than the SYSDIV field in the RCC register
so that additional larger divisors up to /64 are possible, allowing a lower system clock frequency for
improved Deep Sleep power consumption. When using the PLL, the VCO frequency of 400 MHz is
predivided by 2 before the divisor is applied. The divisor is equivalent to the SYSDIV2 encoding
plus 1. Table 5-5 shows how the SYSDIV2 encoding affects the system clock frequency, depending
on whether the PLL is used (BYPASS2=0) or another clock source is used (BYPASS2=1). For a list
of possible clock sources, see Table 5-3 on page 215.
Table 5-5. Examples of Possible System Clock Frequencies Using the SYSDIV2 Field
SYSDIV2
0x00
Divisor
/1
a
Frequency
(BYPASS2=0)
Frequency (BYPASS2=1)
TivaWare Parameter
reserved
Clock source frequency/1
SYSCTL_SYSDIV_1
0x01
/2
reserved
Clock source frequency/2
SYSCTL_SYSDIV_2
0x02
/3
66.67 MHz
Clock source frequency/3
SYSCTL_SYSDIV_3
0x03
/4
50 MHz
Clock source frequency/4
SYSCTL_SYSDIV_4
0x04
/5
40 MHz
Clock source frequency/5
SYSCTL_SYSDIV_5
...
...
...
...
...
0x09
/10
20 MHz
Clock source frequency/10
SYSCTL_SYSDIV_10
...
...
...
...
...
0x3F
/64
3.125 MHz
Clock source frequency/64
SYSCTL_SYSDIV_64
a. This parameter is used in functions such as SysCtlClockSet() in the TivaWare Peripheral Driver Library.
To allow for additional frequency choices when using the PLL, the DIV400 bit is provided along
with the SYSDIV2LSB bit. When the DIV400 bit is set, bit 22 becomes the LSB for SYSDIV2. In
218
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
this situation, the divisor is equivalent to the (SYSDIV2 encoding with SYSDIV2LSB appended) plus
one. Table 5-6 shows the frequency choices when DIV400 is set. When the DIV400 bit is clear,
SYSDIV2LSB is ignored, and the system clock frequency is determined as shown in Table
5-5 on page 218.
Table 5-6. Examples of Possible System Clock Frequencies with DIV400=1
/2
reserved
-
0
/3
reserved
-
1
/4
reserved
-
0
/5
80 MHz
SYSCTL_SYSDIV_2_5
1
/6
66.67 MHz
SYSCTL_SYSDIV_3
0
/7
reserved
-
1
/8
50 MHz
SYSCTL_SYSDIV_4
0
/9
44.44 MHz
SYSCTL_SYSDIV_4_5
1
/10
40 MHz
SYSCTL_SYSDIV_5
...
...
...
...
0
/127
3.15 MHz
SYSCTL_SYSDIV_63_5
1
/128
3.125 MHz
SYSCTL_SYSDIV_64
0x00
reserved
0x01
0x02
0x03
0x04
...
0x3F
b
TivaWare Parameter
SYSDIV2LSB
Divisor
a
Frequency (BYPASS2=0)
SYSDIV2
a. Note that DIV400 and SYSDIV2LSB are only valid when BYPASS2=0.
b. This parameter is used in functions such as SysCtlClockSet() in the TivaWare Peripheral Driver Library.
5.2.5.3
Precision Internal Oscillator Operation (PIOSC)
The microcontroller powers up with the PIOSC running. If another clock source is desired, the PIOSC
must remain enabled as it is used for internal functions. The PIOSC can only be disabled during
Deep-Sleep mode. It can be powered down by setting the PIOSCPD bit in the DSLPCLKCFG register.
The PIOSC generates a 16-MHz clock with ±1% accuracy with calibration and ±3% accuracy across
temperature (see “PIOSC Specifications” on page 1243). At the factory, the PIOSC is set to 16 MHz,
however, the frequency can be trimmed for other voltage or temperature conditions using software
in one of three ways:
■ Default calibration: clear the UTEN bit and set the UPDATE bit in the Precision Internal Oscillator
Calibration (PIOSCCAL) register.
■ User-defined calibration: The user can program the UT value to adjust the PIOSC frequency. As
the UT value increases, the generated period increases. To commit a new UT value, first set the
UTEN bit, then program the UT field, and then set the UPDATE bit. The adjustment finishes within
a few clock periods and is glitch free.
■ Automatic calibration using the Hibernation module with a functioning 32.768-kHz clock source:
Set the CAL bit in the PIOSCCAL register; the results of the calibration are shown in the RESULT
field in the Precision Internal Oscillator Statistic (PIOSCSTAT) register. After calibration is
complete, the PIOSC is trimmed using the trimmed value returned in the CT field.
5.2.5.4
Crystal Configuration for the Main Oscillator (MOSC)
The main oscillator supports the use of a select number of crystals from 4 to 25 MHz.
The XTAL bit in the RCC register (see page 247) describes the available crystal choices and default
programming values.
June 12, 2014
219
Texas Instruments-Production Data
System Control
Software configures the RCC register XTAL field with the crystal number. If the PLL is used in the
design, the XTAL field value is internally translated to the PLL settings.
5.2.5.5
Main PLL Frequency Configuration
The main PLL is disabled by default during power-on reset and is enabled later by software if
required. Software specifies the output divisor to set the system clock frequency and enables the
main PLL to drive the output. The PLL operates at 400 MHz, but is divided by two prior to the
application of the output divisor, unless the DIV400 bit in the RCC2 register is set.
To configure the PIOSC to be the clock source for the main PLL, program the OSCRC2 field in the
Run-Mode Clock Configuration 2 (RCC2) register to be 0x1.
If the main oscillator provides the clock reference to the main PLL, the translation provided by
hardware and used to program the PLL is available for software in the PLL Frequency n
(PLLFREQn) registers (see page 264). The internal translation provides a translation within ± 1% of
the targeted PLL VCO frequency. Table 23-14 on page 1242 shows the actual PLL frequency and
error for a given crystal choice.
The Crystal Value field (XTAL) in the Run-Mode Clock Configuration (RCC) register (see page 247)
describes the available crystal choices and default programming of the PLLFREQn registers. Any
time the XTAL field changes, the new settings are translated and the internal PLL settings are
updated.
5.2.5.6
PLL Modes
■ Normal: The PLL multiplies the input clock reference and drives the output.
■ Power-Down: Most of the PLL internal circuitry is disabled and the PLL does not drive the output.
The modes are programmed using the RCC/RCC2 register fields (see page 247 and page 253).
5.2.5.7
PLL Operation
If a PLL configuration is changed, the PLL output frequency is unstable until it reconverges (relocks)
to the new setting. The time between the configuration change and relock is TREADY (see Table
23-13 on page 1242). During the relock time, the affected PLL is not usable as a clock reference.
Software can poll the LOCK bit in the PLL Status (PLLSTAT) register to determine when the PLL
has locked.
The PLL is changed by one of the following:
■ Change to the XTAL value in the RCC register—writes of the same value do not cause a relock.
■ Change in the PLL from Power-Down to Normal mode.
A counter clocked by the system clock is used to measure the TREADY requirement. The down
counter is set to 0x200 if the PLL is powering up. If the M or N values in the PLLFREQn registers
are changed, the counter is set to 0xC0. Hardware is provided to keep the PLL from being used as
a system clock until the TREADY condition is met after one of the two changes above. It is the user's
responsibility to have a stable clock source (like the main oscillator) before the RCC/RCC2 register
is switched to use the PLL.
If the main PLL is enabled and the system clock is switched to use the PLL in one step, the system
control hardware continues to clock the microcontroller from the oscillator selected by the RCC/RCC2
register until the main PLL is stable (TREADY time met), after which it changes to the PLL. Software
can use many methods to ensure that the system is clocked from the main PLL, including periodically
220
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
polling the PLLLRIS bit in the Raw Interrupt Status (RIS) register, and enabling the PLL Lock
interrupt.
5.2.5.8
Main Oscillator Verification Circuit
The clock control includes circuitry to ensure that the main oscillator is running at the appropriate
frequency. The circuit monitors the main oscillator frequency and signals if the frequency is outside
of the allowable band of attached crystals.
The detection circuit is enabled using the CVAL bit in the Main Oscillator Control (MOSCCTL)
register. If this circuit is enabled and detects an error, and if the MOSCIM bit in the MOSCCTL register
is clear, then the following sequence is performed by the hardware:
1. The MOSCFAIL bit in the Reset Cause (RESC) register is set.
2. The system clock is switched from the main oscillator to the PIOSC.
3. An internal power-on reset is initiated.
4. Reset is deasserted and the processor is directed to the NMI handler during the reset sequence.
if the MOSCIM bit in the MOSCCTL register is set, then the following sequence is performed by the
hardware:
1. The system clock is switched from the main oscillator to the PIOSC.
2. The MOFRIS bit in the RIS register is set to indicate a MOSC failure.
5.2.6
System Control
For power-savings purposes, the peripheral-specific RCGCx, SCGCx, and DCGCx registers (for
example, RCGCWD) control the clock gating logic for that peripheral or block in the system while
the microcontroller is in Run, Sleep, and Deep-Sleep mode, respectively. These registers are located
in the System Control register map starting at offsets 0x600, 0x700, and 0x800, respectively. There
must be a delay of 3 system clocks after a peripheral module clock is enabled in the RCGC register
before any module registers are accessed.
Important: To support legacy software, the RCGCn, SCGCn, and DCGCn registers are available
at offsets 0x100 - 0x128. A write to any of these legacy registers also writes the
corresponding bit in the peripheral-specific RCGCx, SCGCx, and DCGCx registers.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. It is recommended that new software use the new
registers and not rely on legacy operation.
If software uses a peripheral-specific register to write a legacy peripheral (such as
TIMER0), the write causes proper operation, but the value of that bit is not reflected in
the legacy register. Any bits that are changed by writing to a legacy register can be
read back correctly with a read of the legacy register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
There are four levels of operation for the microcontroller defined as:
■ Run mode
June 12, 2014
221
Texas Instruments-Production Data
System Control
■ Sleep mode
■ Deep-Sleep mode
■ Hibernate mode
The following sections describe the different modes in detail.
Caution – If the Cortex-M4F Debug Access Port (DAP) has been enabled, and the device wakes from
a low power sleep or deep-sleep mode, the core may start executing code before all clocks to peripherals
have been restored to their Run mode configuration. The DAP is usually enabled by software tools
accessing the JTAG or SWD interface when debugging or flash programming. If this condition occurs,
a Hard Fault is triggered when software accesses a peripheral with an invalid clock.
A software delay loop can be used at the beginning of the interrupt routine that is used to wake up a
system from a WFI (Wait For Interrupt) instruction. This stalls the execution of any code that accesses
a peripheral register that might cause a fault. This loop can be removed for production software as the
DAP is most likely not enabled during normal execution.
Because the DAP is disabled by default (power on reset), the user can also power cycle the device. The
DAP is not enabled unless it is enabled through the JTAG or SWD interface.
5.2.6.1
Run Mode
In Run mode, the microcontroller actively executes code. Run mode provides normal operation of
the processor and all of the peripherals that are currently enabled by the peripheral-specific RCGC
registers. The system clock can be any of the available clock sources including the PLL.
5.2.6.2
Sleep Mode
In Sleep mode, the clock frequency of the active peripherals is unchanged, but the processor and
the memory subsystem are not clocked and therefore no longer execute code. Sleep mode is entered
by the Cortex-M4F core executing a WFI (Wait for Interrupt) instruction. Any properly configured
interrupt event in the system brings the processor back into Run mode. See “Power
Management” on page 109 for more details.
Peripherals are clocked that are enabled in the peripheral-specific SCGC registers when auto-clock
gating is enabled (see the RCC register) or the peripheral-specific RCGC registers when the
auto-clock gating is disabled. The system clock has the same source and frequency as that during
Run mode.
Additional sleep modes are available that lower the power consumption of the SRAM and Flash
memory. However, the lower power consumption modes have slower sleep and wake-up times,
see “Dynamic Power Management” on page 224 for more information.
Important: Before executing the WFI instruction, software must confirm that the EEPROM is not
busy by checking to see that the WORKING bit in the EEPROM Done Status (EEDONE)
register is clear.
5.2.6.3
Deep-Sleep Mode
In Deep-Sleep mode, the clock frequency of the active peripherals may change (depending on the
Deep-Sleep mode clock configuration) in addition to the processor clock being stopped. An interrupt
returns the microcontroller to Run mode from one of the sleep modes; the sleep modes are entered
on request from the code. Deep-Sleep mode is entered by first setting the SLEEPDEEP bit in the
System Control (SYSCTRL) register (see page 161) and then executing a WFI instruction. Any
222
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
properly configured interrupt event in the system brings the processor back into Run mode. See
“Power Management” on page 109 for more details.
The Cortex-M4F processor core and the memory subsystem are not clocked in Deep-Sleep mode.
Peripherals are clocked that are enabled in the peripheral-specific DCGC registers when auto-clock
gating is enabled (see the RCC register) or the peripheral-specific RCGC registers when auto-clock
gating is disabled. The system clock source is specified in the DSLPCLKCFG register. When the
DSLPCLKCFG register is used, the internal oscillator source is powered up, if necessary, and other
clocks are powered down. If the PLL is running at the time of the WFI instruction, hardware powers
the PLL down and overrides the SYSDIV field of the active RCC/RCC2 register, to be determined
by the DSDIVORIDE setting in the DSLPCLKCFG register, up to /16 or /64 respectively. USB PLL
is not powered down by execution of WFI instruction. When the Deep-Sleep exit event occurs,
hardware brings the system clock back to the source and frequency it had at the onset of Deep-Sleep
mode before enabling the clocks that had been stopped during the Deep-Sleep duration. If the
PIOSC is used as the PLL reference clock source, it may continue to provide the clock during
Deep-Sleep. See page 257.
Important: Before executing the WFI instruction, software must confirm that the EEPROM is not
busy by checking to see that the WORKING bit in the EEPROM Done Status (EEDONE)
register is clear.
To provide the lowest possible Deep-Sleep power consumption as well the ability to wake the
processor from a peripheral without reconfiguring the peripheral for a change in clock, some of the
communications modules have a Clock Control register at offset 0xFC8 in the module register space.
The CS field in the Clock Control register allows the user to select the PIOSC as the clock source
for the module's baud clock. When the microcontroller enters Deep-Sleep mode, the PIOSC becomes
the source for the module clock as well, which allows the transmit and receive FIFOs to continue
operation while the part is in Deep-Sleep. Figure 5-6 on page 223 shows how the clocks are selected.
Figure 5-6. Module Clock Selection
Clock Control Register
PIOSC
1
Baud Clock
0
Deep Sleep
1
Module Clock
System Clock
0
Additional deep-sleep modes are available that lower the power consumption of the SRAM and
Flash memory. However, the lower power consumption modes have slower deep-sleep and wake-up
times, see “Dynamic Power Management” on page 224 for more information.
June 12, 2014
223
Texas Instruments-Production Data
System Control
5.2.6.4
Dynamic Power Management
In addition to the Sleep and Deep-Sleep modes and the clock gating for the on-chip modules, there
are several additional power mode options that allow the LDO, Flash memory, and SRAM into
different levels of power savings while in Sleep or Deep-Sleep modes. Note that these features may
not be available on all devices; the System Properties (SYSPROP) register provides information
on whether a mode is supported on a given MCU. The following registers provides these capabilities:
■ LDO Sleep Power Control (LDOSPCTL): controls the LDO value in Sleep mode
■ LDO Deep-Sleep Power Control (LDODPCTL): controls the LDO value in Deep-Sleep mode
■ LDO Sleep Power Calibration (LDOSPCAL): provides factory recommendations for the LDO
value in Sleep mode
■ LDO Deep-Sleep Power Calibration (LDODPCAL): provides factory recommendations for the
LDO value in Deep-Sleep mode
■ Sleep Power Configuration (SLPPWRCFG): controls the power saving modes for Flash memory
and SRAM in Sleep mode
■ Deep-Sleep Power Configuration (DSLPPWRCFG): controls the power saving modes for Flash
memory and SRAM in Deep-Sleep mode
■ Deep-Sleep Clock Configuration (DSLPCLKCFG): controls the clocking in Deep-Sleep mode
■ Sleep / Deep-Sleep Power Mode Status (SDPMST): provides status information on the various
power saving events
LDO Sleep/Deep-Sleep Power Control
Note:
While the device is connected through JTAG, the LDO control settings for Sleep or
Deep-Sleep are not available and will not be applied.
The user can dynamically request to raise or lower the LDO voltage level to trade-off
power/performance using either the LDOSPCTL register (see page 271) or the LDODPCTL register
(see page 274). When lowering the LDO level, software must configure the system clock for the lower
LDO value in RCC/RCC2 for Sleep mode and in DSLPCLKCFG for Deep-Sleep mode before
requesting the LDO to lower.
The LDO Power Calibration registers, LDOSPCAL and LDODPCAL, provide suggested values for
the LDO in the various modes. If software requests an LDO value that is too low or too high, the
value is not accepted and an error is reported in the SDPMST register.
The table below shows the maximum system clock frequency and PIOSC frequency with respect
to the configured LDO voltage.
Operating Voltage (LDO)
Maximum System Clock Frequency
PIOSC
1.2
80 MHz
16 MHz
0.9
20 MHz
16 MHz
Flash Memory and SRAM Power Control
During Sleep or Deep-Sleep mode, Flash memory can be in either the default active mode or the
low power mode; SRAM can be in the default active mode, standby mode, or low power mode. The
active mode in each case provides the fastest times to sleep and wake up, but consumes more
224
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
power. Low power mode provides the lowest power consumption, but takes longer to sleep and
wake up.
The SRAM can be programmed to prohibit any power management by configuring the SRAMSM bit
in the System Properties (SYSPROP) register. This configuration operates in the same way that
®
legacy Stellaris devices operate and provides the fastest sleep and wake-up times, but consumes
the most power while in Sleep and Deep-Sleep mode. Other power options are retention mode, and
retention mode with lower SRAM voltage. The SRAM retention mode with lower SRAM voltage
provides the lowest power consumption, but has the longest sleep and wake-up times. These modes
can be independently configured for Flash memory and SRAM using the SLPPWRCFG and
DSLPPWRCFG registers.
The following power saving options are available in Sleep and Deep-Sleep modes:
■ The clocks can be gated according to the settings in the the peripheral-specific SCGC or DCGC
registers.
■ In Deep-Sleep mode, the clock source can be changed and the PIOSC can be powered off (if
no active peripheral requires it) using the DSLPCLKCFG register. These options are not available
for Sleep mode.
■ The LDO voltage can be changed using the LDOSPCTL or LDODPCTL register.
■ The Flash memory can be put into low power mode. Refer to Table 23-23 on page 1249 for wake
times from Sleep and Deep-Sleep.
■ The SRAM can be put into standby or low power mode. Refer to Table 23-23 on page 1249 for
wake times from Sleep and Deep-Sleep.
The SDPMST register provides results on the Dynamic Power Management command issued. It
also has some real time status that can be viewed by a debugger or the core if it is running. These
events do not trigger an interrupt and are meant to provide information to help tune software for
power management. The status register gets written at the beginning of every Dynamic Power
Management event request that provides error checking. There is no mechanism to clear the bits;
they are overwritten on the next event. The real time data is real time and there is no event to register
that information.
5.2.6.5
Hibernate Mode
In this mode, the power supplies are turned off to the main part of the microcontroller and only the
Hibernation module's circuitry is active. An external wake event or RTC event is required to bring
the microcontroller back to Run mode. The Cortex-M4F processor and peripherals outside of the
Hibernation module see a normal "power on" sequence and the processor starts running code.
Software can determine if the microcontroller has been restarted from Hibernate mode by inspecting
the Hibernation module registers. For more information on the operation of Hibernate mode, see
“Hibernation Module” on page 481.
5.3
Initialization and Configuration
The PLL is configured using direct register writes to the RCC/RCC2 register. If the RCC2 register
is being used, the USERCC2 bit must be set and the appropriate RCC2 bit/field is used. The steps
required to successfully change the PLL-based system clock are:
1. Bypass the PLL and system clock divider by setting the BYPASS bit and clearing the USESYS
bit in the RCC register, thereby configuring the microcontroller to run off a "raw" clock source
June 12, 2014
225
Texas Instruments-Production Data
System Control
and allowing for the new PLL configuration to be validated before switching the system clock
to the PLL.
2. Select the crystal value (XTAL) and oscillator source (OSCSRC), and clear the PWRDN bit in
RCC/RCC2. Setting the XTAL field automatically pulls valid PLL configuration data for the
appropriate crystal, and clearing the PWRDN bit powers and enables the PLL and its output.
3. Select the desired system divider (SYSDIV) in RCC/RCC2 and set the USESYS bit in RCC. The
SYSDIV field determines the system frequency for the microcontroller.
4. Wait for the PLL to lock by polling the PLLLRIS bit in the Raw Interrupt Status (RIS) register.
5. Enable use of the PLL by clearing the BYPASS bit in RCC/RCC2.
5.4
Register Map
Table 5-7 on page 226 lists the System Control registers, grouped by function. The offset listed is a
hexadecimal increment to the register's address, relative to the System Control base address of
0x400F.E000.
Note:
Spaces in the System Control register space that are not used are reserved for future or
internal use. Software should not modify any reserved memory address.
Additional Flash and ROM registers defined in the System Control register space are
described in the “Internal Memory” on page 512.
Table 5-7. System Control Register Map
Offset
Name
Type
Reset
Description
See
page
System Control Registers
0x000
DID0
RO
-
Device Identification 0
232
0x004
DID1
RO
0x1070.602E
Device Identification 1
234
0x030
PBORCTL
RW
0x0000.7FFF
Brown-Out Reset Control
237
0x050
RIS
RO
0x0000.0000
Raw Interrupt Status
238
0x054
IMC
RW
0x0000.0000
Interrupt Mask Control
240
0x058
MISC
RW1C
0x0000.0000
Masked Interrupt Status and Clear
242
0x05C
RESC
RW
-
Reset Cause
245
0x060
RCC
RW
0x078E.3AD1
Run-Mode Clock Configuration
247
0x06C
GPIOHBCTL
RW
0x0000.7E00
GPIO High-Performance Bus Control
251
0x070
RCC2
RW
0x07C0.6810
Run-Mode Clock Configuration 2
253
0x07C
MOSCCTL
RW
0x0000.0000
Main Oscillator Control
256
0x144
DSLPCLKCFG
RW
0x0780.0000
Deep Sleep Clock Configuration
257
0x14C
SYSPROP
RO
0x0000.1D31
System Properties
259
0x150
PIOSCCAL
RW
0x0000.0000
Precision Internal Oscillator Calibration
261
0x154
PIOSCSTAT
RO
0x0000.0040
Precision Internal Oscillator Statistics
263
226
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 5-7. System Control Register Map (continued)
Offset
Name
0x160
Description
See
page
Type
Reset
PLLFREQ0
RO
0x0000.0032
PLL Frequency 0
264
0x164
PLLFREQ1
RO
0x0000.0001
PLL Frequency 1
265
0x168
PLLSTAT
RO
0x0000.0000
PLL Status
266
0x188
SLPPWRCFG
RW
0x0000.0000
Sleep Power Configuration
267
0x18C
DSLPPWRCFG
RW
0x0000.0000
Deep-Sleep Power Configuration
269
0x1B4
LDOSPCTL
RW
0x0000.0018
LDO Sleep Power Control
271
0x1B8
LDOSPCAL
RO
0x0000.1818
LDO Sleep Power Calibration
273
0x1BC
LDODPCTL
RW
0x0000.0012
LDO Deep-Sleep Power Control
274
0x1C0
LDODPCAL
RO
0x0000.1212
LDO Deep-Sleep Power Calibration
276
0x1CC
SDPMST
RO
0x0000.0000
Sleep / Deep-Sleep Power Mode Status
277
0x300
PPWD
RO
0x0000.0003
Watchdog Timer Peripheral Present
280
0x304
PPTIMER
RO
0x0000.003F
16/32-Bit General-Purpose Timer Peripheral Present
281
0x308
PPGPIO
RO
0x0000.003F
General-Purpose Input/Output Peripheral Present
283
0x30C
PPDMA
RO
0x0000.0001
Micro Direct Memory Access Peripheral Present
286
0x314
PPHIB
RO
0x0000.0001
Hibernation Peripheral Present
287
0x318
PPUART
RO
0x0000.00FF
Universal Asynchronous Receiver/Transmitter Peripheral
Present
288
0x31C
PPSSI
RO
0x0000.000F
Synchronous Serial Interface Peripheral Present
290
0x320
PPI2C
RO
0x0000.000F
Inter-Integrated Circuit Peripheral Present
292
0x328
PPUSB
RO
0x0000.0000
Universal Serial Bus Peripheral Present
294
0x334
PPCAN
RO
0x0000.0003
Controller Area Network Peripheral Present
295
0x338
PPADC
RO
0x0000.0003
Analog-to-Digital Converter Peripheral Present
296
0x33C
PPACMP
RO
0x0000.0001
Analog Comparator Peripheral Present
297
0x340
PPPWM
RO
0x0000.0003
Pulse Width Modulator Peripheral Present
298
0x344
PPQEI
RO
0x0000.0003
Quadrature Encoder Interface Peripheral Present
299
0x358
PPEEPROM
RO
0x0000.0001
EEPROM Peripheral Present
300
0x35C
PPWTIMER
RO
0x0000.003F
32/64-Bit Wide General-Purpose Timer Peripheral
Present
301
0x500
SRWD
RW
0x0000.0000
Watchdog Timer Software Reset
303
0x504
SRTIMER
RW
0x0000.0000
16/32-Bit General-Purpose Timer Software Reset
305
0x508
SRGPIO
RW
0x0000.0000
General-Purpose Input/Output Software Reset
307
0x50C
SRDMA
RW
0x0000.0000
Micro Direct Memory Access Software Reset
309
0x514
SRHIB
RW
0x0000.0000
Hibernation Software Reset
310
June 12, 2014
227
Texas Instruments-Production Data
System Control
Table 5-7. System Control Register Map (continued)
Offset
Name
0x518
See
page
Type
Reset
Description
SRUART
RW
0x0000.0000
Universal Asynchronous Receiver/Transmitter Software
Reset
311
0x51C
SRSSI
RW
0x0000.0000
Synchronous Serial Interface Software Reset
313
0x520
SRI2C
RW
0x0000.0000
Inter-Integrated Circuit Software Reset
315
0x534
SRCAN
RW
0x0000.0000
Controller Area Network Software Reset
317
0x538
SRADC
RW
0x0000.0000
Analog-to-Digital Converter Software Reset
319
0x53C
SRACMP
RW
0x0000.0000
Analog Comparator Software Reset
321
0x540
SRPWM
RW
0x0000.0000
Pulse Width Modulator Software Reset
322
0x544
SRQEI
RW
0x0000.0000
Quadrature Encoder Interface Software Reset
324
0x558
SREEPROM
RW
0x0000.0000
EEPROM Software Reset
326
0x55C
SRWTIMER
RW
0x0000.0000
32/64-Bit Wide General-Purpose Timer Software Reset
327
0x600
RCGCWD
RW
0x0000.0000
Watchdog Timer Run Mode Clock Gating Control
329
0x604
RCGCTIMER
RW
0x0000.0000
16/32-Bit General-Purpose Timer Run Mode Clock Gating
Control
330
0x608
RCGCGPIO
RW
0x0000.0000
General-Purpose Input/Output Run Mode Clock Gating
Control
332
0x60C
RCGCDMA
RW
0x0000.0000
Micro Direct Memory Access Run Mode Clock Gating
Control
334
0x614
RCGCHIB
RW
0x0000.0001
Hibernation Run Mode Clock Gating Control
335
0x618
RCGCUART
RW
0x0000.0000
Universal Asynchronous Receiver/Transmitter Run Mode
Clock Gating Control
336
0x61C
RCGCSSI
RW
0x0000.0000
Synchronous Serial Interface Run Mode Clock Gating
Control
338
0x620
RCGCI2C
RW
0x0000.0000
Inter-Integrated Circuit Run Mode Clock Gating Control
340
0x634
RCGCCAN
RW
0x0000.0000
Controller Area Network Run Mode Clock Gating Control
342
0x638
RCGCADC
RW
0x0000.0000
Analog-to-Digital Converter Run Mode Clock Gating
Control
343
0x63C
RCGCACMP
RW
0x0000.0000
Analog Comparator Run Mode Clock Gating Control
344
0x640
RCGCPWM
RW
0x0000.0000
Pulse Width Modulator Run Mode Clock Gating Control
345
0x644
RCGCQEI
RW
0x0000.0000
Quadrature Encoder Interface Run Mode Clock Gating
Control
346
0x658
RCGCEEPROM
RW
0x0000.0000
EEPROM Run Mode Clock Gating Control
347
0x65C
RCGCWTIMER
RW
0x0000.0000
32/64-Bit Wide General-Purpose Timer Run Mode Clock
Gating Control
348
0x700
SCGCWD
RW
0x0000.0000
Watchdog Timer Sleep Mode Clock Gating Control
350
228
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 5-7. System Control Register Map (continued)
Offset
Name
0x704
Description
See
page
Type
Reset
SCGCTIMER
RW
0x0000.0000
16/32-Bit General-Purpose Timer Sleep Mode Clock
Gating Control
351
0x708
SCGCGPIO
RW
0x0000.0000
General-Purpose Input/Output Sleep Mode Clock Gating
Control
353
0x70C
SCGCDMA
RW
0x0000.0000
Micro Direct Memory Access Sleep Mode Clock Gating
Control
355
0x714
SCGCHIB
RW
0x0000.0001
Hibernation Sleep Mode Clock Gating Control
356
0x718
SCGCUART
RW
0x0000.0000
Universal Asynchronous Receiver/Transmitter Sleep
Mode Clock Gating Control
357
0x71C
SCGCSSI
RW
0x0000.0000
Synchronous Serial Interface Sleep Mode Clock Gating
Control
359
0x720
SCGCI2C
RW
0x0000.0000
Inter-Integrated Circuit Sleep Mode Clock Gating Control
361
0x734
SCGCCAN
RW
0x0000.0000
Controller Area Network Sleep Mode Clock Gating
Control
363
0x738
SCGCADC
RW
0x0000.0000
Analog-to-Digital Converter Sleep Mode Clock Gating
Control
364
0x73C
SCGCACMP
RW
0x0000.0000
Analog Comparator Sleep Mode Clock Gating Control
365
0x740
SCGCPWM
RW
0x0000.0000
Pulse Width Modulator Sleep Mode Clock Gating Control
366
0x744
SCGCQEI
RW
0x0000.0000
Quadrature Encoder Interface Sleep Mode Clock Gating
Control
367
0x758
SCGCEEPROM
RW
0x0000.0000
EEPROM Sleep Mode Clock Gating Control
368
0x75C
SCGCWTIMER
RW
0x0000.0000
32/64-Bit Wide General-Purpose Timer Sleep Mode Clock
Gating Control
369
0x800
DCGCWD
RW
0x0000.0000
Watchdog Timer Deep-Sleep Mode Clock Gating Control
371
0x804
DCGCTIMER
RW
0x0000.0000
16/32-Bit General-Purpose Timer Deep-Sleep Mode
Clock Gating Control
372
0x808
DCGCGPIO
RW
0x0000.0000
General-Purpose Input/Output Deep-Sleep Mode Clock
Gating Control
374
0x80C
DCGCDMA
RW
0x0000.0000
Micro Direct Memory Access Deep-Sleep Mode Clock
Gating Control
376
0x814
DCGCHIB
RW
0x0000.0001
Hibernation Deep-Sleep Mode Clock Gating Control
377
0x818
DCGCUART
RW
0x0000.0000
Universal Asynchronous Receiver/Transmitter
Deep-Sleep Mode Clock Gating Control
378
0x81C
DCGCSSI
RW
0x0000.0000
Synchronous Serial Interface Deep-Sleep Mode Clock
Gating Control
380
0x820
DCGCI2C
RW
0x0000.0000
Inter-Integrated Circuit Deep-Sleep Mode Clock Gating
Control
382
0x834
DCGCCAN
RW
0x0000.0000
Controller Area Network Deep-Sleep Mode Clock Gating
Control
384
June 12, 2014
229
Texas Instruments-Production Data
System Control
Table 5-7. System Control Register Map (continued)
Offset
Name
0x838
See
page
Type
Reset
Description
DCGCADC
RW
0x0000.0000
Analog-to-Digital Converter Deep-Sleep Mode Clock
Gating Control
385
0x83C
DCGCACMP
RW
0x0000.0000
Analog Comparator Deep-Sleep Mode Clock Gating
Control
386
0x840
DCGCPWM
RW
0x0000.0000
Pulse Width Modulator Deep-Sleep Mode Clock Gating
Control
387
0x844
DCGCQEI
RW
0x0000.0000
Quadrature Encoder Interface Deep-Sleep Mode Clock
Gating Control
388
0x858
DCGCEEPROM
RW
0x0000.0000
EEPROM Deep-Sleep Mode Clock Gating Control
389
0x85C
DCGCWTIMER
RW
0x0000.0000
32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode
Clock Gating Control
390
0xA00
PRWD
RO
0x0000.0000
Watchdog Timer Peripheral Ready
392
0xA04
PRTIMER
RO
0x0000.0000
16/32-Bit General-Purpose Timer Peripheral Ready
393
0xA08
PRGPIO
RO
0x0000.0000
General-Purpose Input/Output Peripheral Ready
395
0xA0C
PRDMA
RO
0x0000.0000
Micro Direct Memory Access Peripheral Ready
397
0xA14
PRHIB
RO
0x0000.0001
Hibernation Peripheral Ready
398
0xA18
PRUART
RO
0x0000.0000
Universal Asynchronous Receiver/Transmitter Peripheral
Ready
399
0xA1C
PRSSI
RO
0x0000.0000
Synchronous Serial Interface Peripheral Ready
401
0xA20
PRI2C
RO
0x0000.0000
Inter-Integrated Circuit Peripheral Ready
403
0xA34
PRCAN
RO
0x0000.0000
Controller Area Network Peripheral Ready
405
0xA38
PRADC
RO
0x0000.0000
Analog-to-Digital Converter Peripheral Ready
406
0xA3C
PRACMP
RO
0x0000.0000
Analog Comparator Peripheral Ready
407
0xA40
PRPWM
RO
0x0000.0000
Pulse Width Modulator Peripheral Ready
408
0xA44
PRQEI
RO
0x0000.0000
Quadrature Encoder Interface Peripheral Ready
409
0xA58
PREEPROM
RO
0x0000.0000
EEPROM Peripheral Ready
410
0xA5C
PRWTIMER
RO
0x0000.0000
32/64-Bit Wide General-Purpose Timer Peripheral Ready
411
System Control Legacy Registers
0x008
DC0
RO
0x007F.003F
Device Capabilities 0
413
0x010
DC1
RO
0x1333.2FFF
Device Capabilities 1
415
0x014
DC2
RO
0x030F.F337
Device Capabilities 2
418
0x018
DC3
RO
0xBFFF.8FFF
Device Capabilities 3
421
0x01C
DC4
RO
0x0004.F03F
Device Capabilities 4
425
0x020
DC5
RO
0x0130.00FF
Device Capabilities 5
428
0x024
DC6
RO
0x0000.0000
Device Capabilities 6
430
230
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 5-7. System Control Register Map (continued)
Offset
Name
0x028
Reset
DC7
RO
0xFFFF.FFFF
Device Capabilities 7
431
0x02C
DC8
RO
0x0FFF.0FFF
Device Capabilities 8
434
0x040
SRCR0
RO
0x0000.0000
Software Reset Control 0
437
0x044
SRCR1
RO
0x0000.0000
Software Reset Control 1
439
0x048
SRCR2
RO
0x0000.0000
Software Reset Control 2
442
0x100
RCGC0
RO
0x0000.0040
Run Mode Clock Gating Control Register 0
444
0x104
RCGC1
RO
0x0000.0000
Run Mode Clock Gating Control Register 1
448
0x108
RCGC2
RO
0x0000.0000
Run Mode Clock Gating Control Register 2
452
0x110
SCGC0
RO
0x0000.0040
Sleep Mode Clock Gating Control Register 0
454
0x114
SCGC1
RO
0x0000.0000
Sleep Mode Clock Gating Control Register 1
457
0x118
SCGC2
RO
0x0000.0000
Sleep Mode Clock Gating Control Register 2
460
0x120
DCGC0
RO
0x0000.0040
Deep Sleep Mode Clock Gating Control Register 0
462
0x124
DCGC1
RO
0x0000.0000
Deep-Sleep Mode Clock Gating Control Register 1
465
0x128
DCGC2
RO
0x0000.0000
Deep Sleep Mode Clock Gating Control Register 2
468
0x190
DC9
RO
0x00FF.00FF
Device Capabilities 9
470
0x1A0
NVMSTAT
RO
0x0000.0001
Non-Volatile Memory Information
472
5.5
Description
See
page
Type
System Control Register Descriptions
All addresses given are relative to the System Control base address of 0x400F.E000. Registers
provided for legacy software support only are listed in “System Control Legacy Register
Descriptions” on page 412.
June 12, 2014
231
Texas Instruments-Production Data
System Control
Register 1: Device Identification 0 (DID0), offset 0x000
This register identifies the version of the microcontroller. Each microcontroller is uniquely identified
by the combined values of the CLASS field in the DID0 register and the PARTNO field in the DID1
register. The MAJOR and MINOR bit fields indicate the die revision number. Combined, the MAJOR
and MINOR bit fields indicate the part revision number.
MAJOR Bitfield Value
MINOR Bitfield Value
Die Revision
Part Revision
0x0
0x0
A0
1
0x0
0x1
A1
2
0x0
0x2
A2
3
0x0
0x3
A3
4
0x1
0x0
B0
5
0x1
0x1
B1
6
0x1
0x2
B2
7
Device Identification 0 (DID0)
Base 0x400F.E000
Offset 0x000
Type RO, reset 31
30
reserved
Type
Reset
29
28
27
26
VER
25
24
23
22
21
20
reserved
18
17
16
CLASS
RO
0
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
MAJOR
Type
Reset
19
MINOR
Bit/Field
Name
Type
Reset
31
reserved
RO
0
30:28
VER
RO
0x01
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
DID0 Version
This field defines the DID0 register format version. The version number
is numeric. The value of the VER field is encoded as follows (all other
encodings are reserved):
Value Description
0x1
27:24
reserved
RO
0x08
Second version of the DID0 register format.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
232
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
Description
23:16
CLASS
RO
0x05
Device Class
The CLASS field value identifies the internal design from which all mask
sets are generated for all microcontrollers in a particular product line.
The CLASS field value is changed for new product lines, for changes in
fab process (for example, a remap or shrink), or any case where the
MAJOR or MINOR fields require differentiation from prior microcontrollers.
The value of the CLASS field is encoded as follows (all other encodings
are reserved):
Value Description
0x05 Tiva™ TM4C123x microcontrollers
15:8
MAJOR
RO
-
Major Die Revision
This field specifies the major revision number of the microcontroller.
The major revision reflects changes to base layers of the design. This
field is encoded as follows:
Value Description
0x0
Revision A (initial device)
0x1
Revision B (first base layer revision)
0x2
Revision C (second base layer revision)
and so on.
7:0
MINOR
RO
-
Minor Die Revision
This field specifies the minor revision number of the microcontroller.
The minor revision reflects changes to the metal layers of the design.
The MINOR field value is reset when the MAJOR field is changed. This
field is numeric and is encoded as follows:
Value Description
0x0
Initial device, or a major revision update.
0x1
First metal layer change.
0x2
Second metal layer change.
and so on.
June 12, 2014
233
Texas Instruments-Production Data
System Control
Register 2: Device Identification 1 (DID1), offset 0x004
This register identifies the device family, part number, temperature range, pin count, and package
type. Each microcontroller is uniquely identified by the combined values of the CLASS field in the
DID0 register and the PARTNO field in the DID1 register.
Device Identification 1 (DID1)
Base 0x400F.E000
Offset 0x004
Type RO, reset 0x1070.602E
31
30
29
28
27
26
RO
0
15
25
24
23
22
21
20
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
1
14
13
12
11
10
9
8
7
6
5
4
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
VER
Type
Reset
FAM
PINCOUNT
Type
Reset
RO
0
RO
1
18
17
16
RO
0
RO
0
RO
0
RO
0
3
2
1
0
PARTNO
reserved
RO
0
19
TEMP
Bit/Field
Name
Type
Reset
31:28
VER
RO
0x1
RO
0
PKG
ROHS
RO
1
RO
1
QUAL
RO
1
RO
0
Description
DID1 Version
This field defines the DID1 register format version. The version number
is numeric. The value of the VER field is encoded as follows (all other
encodings are reserved):
Value Description
27:24
FAM
RO
0x0
0x0
Initial DID1 register format definition, indicating a Stellaris
LM3Snnn device.
0x1
Second version of the DID1 register format.
Family
This field provides the family identification of the device within the product
portfolio. The value is encoded as follows (all other encodings are
reserved):
Value Description
0x0
23:16
PARTNO
RO
0x70
Tiva™ C Series microcontrollers and legacy Stellaris
microcontrollers, that is, all devices with external part numbers
starting with TM4C, LM4F or LM3S.
Part Number
This field provides the part number of the device within the family. The
reset value shown indicates the TM4C123BE6PM microcontroller.
234
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
15:13
PINCOUNT
RO
0x3
Description
Package Pin Count
This field specifies the number of pins on the device package. The value
is encoded as follows (all other encodings are reserved):
Value Description
12:8
reserved
RO
0
7:5
TEMP
RO
0x1
0x0
reserved
0x1
reserved
0x2
100-pin package
0x3
64-pin package
0x4
144-pin package
0x5
157-pin package
0x6
168-pin package
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Temperature Range
This field specifies the temperature rating of the device. The value is
encoded as follows (all other encodings are reserved):
Value Description
4:3
PKG
RO
0x1
0x0
Reserved
0x1
Industrial temperature range (-40°C to 85°C)
0x2
Extended temperature range (-40°C to 105°C)
0x3
Available in both industrial temperature range (-40°C to 85°C)
and extended temperature range (-40°C to 105°C) devices. See
“Package Information” on page 1269 for specific order numbers.
Package Type
This field specifies the package type. The value is encoded as follows
(all other encodings are reserved):
Value Description
2
ROHS
RO
0x1
0x0
Reserved
0x1
LQFP package
0x2
BGA package
RoHS-Compliance
This bit specifies whether the device is RoHS-compliant. A 1 indicates
the part is RoHS-compliant.
June 12, 2014
235
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1:0
QUAL
RO
0x2
Description
Qualification Status
This field specifies the qualification status of the device. The value is
encoded as follows (all other encodings are reserved):
Value Description
0x0
Engineering Sample (unqualified)
0x1
Pilot Production (unqualified)
0x2
Fully Qualified
236
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 3: Brown-Out Reset Control (PBORCTL), offset 0x030
This register is responsible for controlling reset conditions after initial power-on reset.
Note:
The BOR voltage values and center points are based on simulation only. These values are
yet to be characterized and are subject to change.
Brown-Out Reset Control (PBORCTL)
Base 0x400F.E000
Offset 0x030
Type RW, reset 0x0000.7FFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
4
3
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
2
1
0
BOR0
BOR1
reserved
RW
1
RW
1
RO
0
Bit/Field
Name
Type
Reset
Description
31:3
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
2
BOR0
RW
1
VDD under BOR0 Event Action
The VDD BOR0 trip value is 3.02V +/- 90mv.
Value Description
1
BOR1
RW
1
0
A BOR0 event causes an interrupt to be generated in the
interrupt controller.
1
A BOR0 event causes a reset of the microcontroller.
VDD under BOR1 Event Action
The VDD BOR1 trip value is 2.88V +/- 90mv.
Value Description
0
reserved
RO
0
0
A BOR1 event causes an interrupt to be generated to the
interrupt controller.
1
A BOR1 event causes a reset of the microcontroller.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
237
Texas Instruments-Production Data
System Control
Register 4: Raw Interrupt Status (RIS), offset 0x050
This register indicates the status for system control raw interrupts. An interrupt is sent to the interrupt
controller if the corresponding bit in the Interrupt Mask Control (IMC) register is set. Writing a 1
to the corresponding bit in the Masked Interrupt Status and Clear (MISC) register clears an interrupt
status bit.
Raw Interrupt Status (RIS)
Base 0x400F.E000
Offset 0x050
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
reserved
Type
Reset
reserved
Type
Reset
BOR0RIS VDDARIS reserved
RO
0
RO
0
RO
0
RO
0
MOSCPUPRIS
RO
0
Bit/Field
Name
Type
Reset
31:12
reserved
RO
0x0000.00
11
BOR0RIS
RO
0
RO
0
reserved PLLLRIS
RO
0
RO
0
reserved
RO
0
MOFRIS
RO
0
RO
0
reserved BOR1RIS reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
VDD under BOR0 Raw Interrupt Status
Value Description
0
A VDD BOR0 condition is not currently active.
1
A VDD BOR0 condition is currently active.
Note the BOR0 bit in the PBORCTL register must be cleared to cause
an interrupt due to a BOR0 Event.
This bit is cleared by writing a 1 to the BOR0MIS bit in the MISC register.
10
VDDARIS
RO
0
VDDA Power OK Event Raw Interrupt Status
Value Description
0
VDDA power is not at its appropriate functional voltage.
1
VDDA is at an appropriate functional voltage.
This bit is cleared by writing a 1 to the VDDAMIS bit in the MISC register.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
238
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
8
MOSCPUPRIS
RO
0
Description
MOSC Power Up Raw Interrupt Status
Value Description
0
Sufficient time has not passed for the MOSC to reach the
expected frequency.
1
Sufficient time has passed for the MOSC to reach the expected
frequency. The value for this power-up time is indicated by
TMOSC_START.
This bit is cleared by writing a 1 to the MOSCPUPMIS bit in the MISC
register.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
PLLLRIS
RO
0
PLL Lock Raw Interrupt Status
Value Description
0
The PLL timer has not reached TREADY.
1
The PLL timer has reached TREADY indicating that sufficient time
has passed for the PLL to lock.
This bit is cleared by writing a 1 to the PLLLMIS bit in the MISC register.
5:4
reserved
RO
0x0
3
MOFRIS
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Failure Raw Interrupt Status
Value Description
0
The main oscillator has not failed.
1
The MOSCIM bit in the MOSCCTL register is set and the main
oscillator has failed.
This bit is cleared by writing a 1 to the MOFMIS bit in the MISC register.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
BOR1RIS
RO
0
VDD under BOR1 Raw Interrupt Status
Value Description
0
A VDDS BOR1 condition is not currently active.
1
A VDDS BOR1 condition is currently active.
Note the BOR1 bit in the PBORCTL register must be cleared to cause
an interrupt due to a BOR1 Event.
This bit is cleared by writing a 1 to the BOR1MIS bit in the MISC register.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
239
Texas Instruments-Production Data
System Control
Register 5: Interrupt Mask Control (IMC), offset 0x054
This register contains the mask bits for system control raw interrupts. A raw interrupt, indicated by
a bit being set in the Raw Interrupt Status (RIS) register, is sent to the interrupt controller if the
corresponding bit in this register is set.
Interrupt Mask Control (IMC)
Base 0x400F.E000
Offset 0x054
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
BOR0IM
VDDAIM
RO
0
RO
0
RW
0
RW
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
reserved
MOSCPUPIM
reserved
PLLLIM
MOFIM
reserved
BOR1IM
reserved
RO
0
RW
0
RO
0
RW
0
RW
0
RO
0
RW
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:12
reserved
RO
0x0000.00
11
BOR0IM
RW
0
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
VDD under BOR0 Interrupt Mask
Value Description
10
VDDAIM
RW
0
0
The BOR0RIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the BOR0RIS
bit in the RIS register is set.
VDDA Power OK Interrupt Mask
Value Description
0
The VDDARIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the VDDARIS
bit in the RIS register is set.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
8
MOSCPUPIM
RW
0
MOSC Power Up Interrupt Mask
Value Description
0
The MOSCPUPRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
MOSCPUPRIS bit in the RIS register is set.
240
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
Description
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
PLLLIM
RW
0
PLL Lock Interrupt Mask
Value Description
5:4
reserved
RO
0x0
3
MOFIM
RW
0
0
The PLLLRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the PLLLRIS
bit in the RIS register is set.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Failure Interrupt Mask
Value Description
0
The MOFRIS interrupt is suppressed and not sent to the interrupt
controller.
1
An interrupt is sent to the interrupt controller when the MOFRIS
bit in the RIS register is set.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
BOR1IM
RW
0
VDD under BOR1 Interrupt Mask
Value Description
0
reserved
RO
0
0
The BOR1RIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the BOR1RIS
bit in the RIS register is set.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
241
Texas Instruments-Production Data
System Control
Register 6: Masked Interrupt Status and Clear (MISC), offset 0x058
On a read, this register gives the current masked status value of the corresponding interrupt in the
Raw Interrupt Status (RIS) register. All of the bits are RW1C, thus writing a 1 to a bit clears the
corresponding raw interrupt bit in the RIS register (see page 238).
Masked Interrupt Status and Clear (MISC)
Base 0x400F.E000
Offset 0x058
Type RW1C, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
reserved
Type
Reset
reserved
Type
Reset
BOR0MIS VDDAMIS reserved
RO
0
RO
0
RW1C
0
RW1C
0
MOSCPUPMIS
RO
0
Bit/Field
Name
Type
Reset
31:12
reserved
RO
0x0000.00
11
BOR0MIS
RW1C
0
RW1C
0
reserved PLLLMIS
RO
0
RW1C
0
reserved
RO
0
RO
0
MOFMIS reserved BOR1MIS reserved
RO
0
RO
0
RW1C
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
VDD under BOR0 Masked Interrupt Status
Value Description
0
When read, a 0 indicates that a BOR0 condition has not
occurred.
A write of 0 has no effect on the state of this bit.
1
When read, a 1 indicates that an unmasked interrupt was
signaled because of a BOR0 condition.
Writing a 1 to this bit clears it and also the BOR0RIS bit in the
RIS register.
10
VDDAMIS
RW1C
0
VDDA Power OK Masked Interrupt Status
Value Description
0
When read, a 0 indicates that VDDA power is good.
A write of 0 has no effect on the state of this bit.
1
When read, a 1 indicates that an unmasked interrupt was
signaled because VDDA was below the proper functioning
voltage.
Writing a 1 to this bit clears it and also the VDDARIS bit in the
RIS register.
9
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
242
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
8
MOSCPUPMIS
RW1C
0
Description
MOSC Power Up Masked Interrupt Status
Value Description
0
When read, a 0 indicates that sufficient time has not passed for
the MOSC PLL to lock.
A write of 0 has no effect on the state of this bit.
1
When read, a 1 indicates that an unmasked interrupt was
signaled because sufficient time has passed for the MOSC PLL
to lock.
Writing a 1 to this bit clears it and also the MOSCPUPRIS bit in
the RIS register.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
6
PLLLMIS
RW1C
0
PLL Lock Masked Interrupt Status
Value Description
0
When read, a 0 indicates that sufficient time has not passed for
the PLL to lock.
A write of 0 has no effect on the state of this bit.
1
When read, a 1 indicates that an unmasked interrupt was
signaled because sufficient time has passed for the PLL to lock.
Writing a 1 to this bit clears it and also the PLLLRIS bit in the
RIS register.
5:4
reserved
RO
0x0
3
MOFMIS
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Failure Masked Interrupt Status
Value Description
0
When read, a 0 indicates that the main oscillator has not failed.
A write of 0 has no effect on the state of this bit.
1
When read, a 1 indicates that an unmasked interrupt was
signaled because the main oscillator failed.
Writing a 1 to this bit clears it and also the MOFRIS bit in the
RIS register.
2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
243
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1
BOR1MIS
RW1C
0
Description
VDD under BOR1 Masked Interrupt Status
Value Description
0
When read, a 0 indicates that a BOR1 condition has not
occurred.
A write of 0 has no effect on the state of this bit.
1
When read, a 1 indicates that an unmasked interrupt was
signaled because of a BOR1 condition.
Writing a 1 to this bit clears it and also the BOR1RIS bit in the
RIS register.
0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
244
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 7: Reset Cause (RESC), offset 0x05C
This register is set with the reset cause after reset. The bits in this register are sticky and maintain
their state across multiple reset sequences, except when an power-on reset is the cause, in which
case, all bits other than POR in the RESC register are cleared.
Reset Cause (RESC)
Base 0x400F.E000
Offset 0x05C
Type RW, reset 31
30
29
28
27
26
25
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
RO
0
RO
0
RO
0
RO
0
RO
0
24
23
22
21
20
19
18
17
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
-
9
8
7
6
5
4
3
2
1
0
WDT1
SW
WDT0
BOR
POR
EXT
RO
0
RO
0
RO
0
RO
0
RW
-
RW
-
RW
-
RW
-
RW
-
RW
-
reserved
Type
Reset
MOSCFAIL
reserved
Type
Reset
RO
0
16
Bit/Field
Name
Type
Reset
Description
31:17
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
16
MOSCFAIL
RW
-
MOSC Failure Reset
Value Description
0
When read, this bit indicates that a MOSC failure has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
1
15:6
reserved
RO
0x00
5
WDT1
RW
-
When read, this bit indicates that the MOSC circuit was enabled
for clock validation and failed while the MOSCIM bit in the
MOSCCTL register is clear, generating a reset event.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Watchdog Timer 1 Reset
Value Description
0
When read, this bit indicates that Watchdog Timer 1 has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
1
When read, this bit indicates that Watchdog Timer 1 timed out
and generated a reset.
June 12, 2014
245
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
SW
RW
-
Description
Software Reset
Value Description
0
When read, this bit indicates that a software reset has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
1
3
WDT0
RW
-
When read, this bit indicates that a software reset has caused
a reset event.
Watchdog Timer 0 Reset
Value Description
0
When read, this bit indicates that Watchdog Timer 0 has not
generated a reset since the previous power-on reset.
Writing a 0 to this bit clears it.
1
2
BOR
RW
-
When read, this bit indicates that Watchdog Timer 0 timed out
and generated a reset.
Brown-Out Reset
Value Description
0
When read, this bit indicates that a brown-out (BOR0 or BOR1)
reset has not generated a reset since the previous power-on
reset.
Writing a 0 to this bit clears it.
1
1
POR
RW
-
When read, this bit indicates that a brown-out (BOR0 or BOR1)
reset has caused a reset event.
Power-On Reset
Value Description
0
When read, this bit indicates that a power-on reset has not
generated a reset.
Writing a 0 to this bit clears it.
1
0
EXT
RW
-
When read, this bit indicates that a power-on reset has caused
a reset event.
External Reset
Value Description
0
When read, this bit indicates that an external reset (RST
assertion) has not caused a reset event since the previous
power-on reset.
Writing a 0 to this bit clears it.
1
When read, this bit indicates that an external reset (RST
assertion) has caused a reset event.
246
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 8: Run-Mode Clock Configuration (RCC), offset 0x060
The bits in this register configure the system clock and oscillators.
Important: Write the RCC register prior to writing the RCC2 register.
Run-Mode Clock Configuration (RCC)
Base 0x400F.E000
Offset 0x060
Type RW, reset 0x078E.3AD1
31
30
29
28
RO
0
RO
0
RO
0
RO
0
15
14
13
12
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
27
26
25
24
23
RW
0
RW
1
RW
1
RW
1
RW
1
11
10
9
8
RW
0
RW
1
ACG
PWRDN
RO
1
21
20
USESYSDIV
reserved
USEPWMDIV
RW
0
RO
0
RW
0
RW
1
RW
1
RW
1
RO
0
7
6
5
4
3
2
1
0
RW
1
RW
1
RW
0
RW
1
RO
0
SYSDIV
reserved BYPASS
RW
1
22
XTAL
RW
1
Bit/Field
Name
Type
Reset
31:28
reserved
RO
0x0
27
ACG
RW
0
RW
0
19
18
17
PWMDIV
OSCSRC
reserved
reserved
RO
0
16
MOSCDIS
RO
0
RW
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Auto Clock Gating
This bit specifies whether the system uses the Sleep-Mode Clock
Gating Control (SCGCn) registers and Deep-Sleep-Mode Clock
Gating Control (DCGCn) registers if the microcontroller enters a Sleep
or Deep-Sleep mode (respectively).
Value Description
0
The Run-Mode Clock Gating Control (RCGCn) registers are
used when the microcontroller enters a sleep mode.
1
The SCGCn or DCGCn registers are used to control the clocks
distributed to the peripherals when the microcontroller is in a
sleep mode. The SCGCn and DCGCn registers allow unused
peripherals to consume less power when the microcontroller is
in a sleep mode.
The RCGCn registers are always used to control the clocks in Run
mode.
26:23
SYSDIV
RW
0xF
System Clock Divisor
Specifies which divisor is used to generate the system clock from either
the PLL output or the oscillator source (depending on how the BYPASS
bit in this register is configured). See Table 5-4 on page 218 for bit
encodings.
If the SYSDIV value is less than MINSYSDIV (see page 415), and the
PLL is being used, then the MINSYSDIV value is used as the divisor.
If the PLL is not being used, the SYSDIV value can be less than
MINSYSDIV.
June 12, 2014
247
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
22
USESYSDIV
RW
0
Description
Enable System Clock Divider
Value Description
0
The system clock is used undivided.
1
The system clock divider is the source for the system clock. The
system clock divider is forced to be used when the PLL is
selected as the source.
If the USERCC2 bit in the RCC2 register is set, then the SYSDIV2
field in the RCC2 register is used as the system clock divider
rather than the SYSDIV field in this register.
21
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
20
USEPWMDIV
RW
0
Enable PWM Clock Divisor
Value Description
0
The system clock is the source for the PWM clock.
1
The PWM clock divider is the source for the PWM clock.
Note that when the PWM divisor is used, it is applied to the clock for
both PWM modules.
19:17
PWMDIV
RW
0x7
PWM Unit Clock Divisor
This field specifies the binary divisor used to predivide the system clock
down for use as the timing reference for the PWM module. The rising
edge of this clock is synchronous with the system clock.
Value Divisor
16:14
reserved
RO
0x0
13
PWRDN
RW
1
0x0
/2
0x1
/4
0x2
/8
0x3
/16
0x4
/32
0x5
/64
0x6
/64
0x7
/64 (default)
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PLL Power Down
Value Description
0
The PLL is operating normally.
1
The PLL is powered down. Care must be taken to ensure that
another clock source is functioning and that the BYPASS bit is
set before setting this bit.
248
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
Description
12
reserved
RO
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
11
BYPASS
RW
1
PLL Bypass
Value Description
0
The system clock is the PLL output clock divided by the divisor
specified by SYSDIV.
1
The system clock is derived from the OSC source and divided
by the divisor specified by SYSDIV.
See Table 5-4 on page 218 for programming guidelines.
Note:
10:6
XTAL
RW
0x0B
The ADC must be clocked from the PLL or directly from a
16-MHz clock source to operate properly.
Crystal Value
This field specifies the crystal value attached to the main oscillator. The
encoding for this field is provided below.
Value
Crystal Frequency (MHz) Not
Using the PLL
0x00-0x5
0x06
Crystal Frequency (MHz)
Using the PLL
reserved
4 MHz
reserved
0x07
4.096 MHz
reserved
0x08
4.9152 MHz
reserved
0x09
5 MHz
0x0A
5.12 MHz
0x0B
6 MHz
0x0C
6.144 MHz
0x0D
7.3728 MHz
0x0E
8 MHz
0x0F
8.192 MHz
0x10
10.0 MHz
0x11
12.0 MHz
0x12
12.288 MHz
0x13
13.56 MHz
0x14
14.31818 MHz
0x15
16.0 MHz
0x16
16.384 MHz
0x17
18.0 MHz
0x18
20.0 MHz
0x19
24.0 MHz
0x1A
25.0 MHz
June 12, 2014
249
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
5:4
OSCSRC
RW
0x1
Description
Oscillator Source
Selects the input source for the OSC. The values are:
Value Input Source
0x0
MOSC
Main oscillator
0x1
PIOSC
Precision internal oscillator
(default)
0x2
PIOSC/4
Precision internal oscillator / 4
0x3
LFIOSC
Low-frequency internal oscillator
For additional oscillator sources, see the RCC2 register.
3:1
reserved
RO
0x0
0
MOSCDIS
RW
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Main Oscillator Disable
Value Description
0
The main oscillator is enabled.
1
The main oscillator is disabled (default).
250
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 9: GPIO High-Performance Bus Control (GPIOHBCTL), offset 0x06C
This register controls which internal bus is used to access each GPIO port. When a bit is clear, the
corresponding GPIO port is accessed across the legacy Advanced Peripheral Bus (APB) bus and
through the APB memory aperture. When a bit is set, the corresponding port is accessed across
the Advanced High-Performance Bus (AHB) bus and through the AHB memory aperture. Each
GPIO port can be individually configured to use AHB or APB, but may be accessed only through
one aperture. The AHB bus provides better back-to-back access performance than the APB bus.
The address aperture in the memory map changes for the ports that are enabled for AHB access
(see Table 10-6 on page 647).
Important: Ports K-N and P-Q are only available on the AHB bus, and therefore the corresponding
bits reset to 1. If one of these bits is cleared, the corresponding port is disabled. If any
of these ports is in use, read-modify-write operations should be used to change the
value of this register so that these ports remain enabled.
GPIO High-Performance Bus Control (GPIOHBCTL)
Base 0x400F.E000
Offset 0x06C
Type RW, reset 0x0000.7E00
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
PORTF
PORTE
PORTD
PORTC
PORTB
PORTA
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.0
5
PORTF
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port F Advanced High-Performance Bus
This bit defines the memory aperture for Port F.
Value Description
4
PORTE
RW
0
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
1
Advanced High-Performance Bus (AHB)
Port E Advanced High-Performance Bus
This bit defines the memory aperture for Port E.
Value Description
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
1
Advanced High-Performance Bus (AHB)
June 12, 2014
251
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
PORTD
RW
0
Description
Port D Advanced High-Performance Bus
This bit defines the memory aperture for Port D.
Value Description
2
PORTC
RW
0
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
1
Advanced High-Performance Bus (AHB)
Port C Advanced High-Performance Bus
This bit defines the memory aperture for Port C.
Value Description
1
PORTB
RW
0
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
1
Advanced High-Performance Bus (AHB)
Port B Advanced High-Performance Bus
This bit defines the memory aperture for Port B.
Value Description
0
PORTA
RW
0
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
1
Advanced High-Performance Bus (AHB)
Port A Advanced High-Performance Bus
This bit defines the memory aperture for Port A.
Value Description
0
Advanced Peripheral Bus (APB). This bus is the legacy bus.
1
Advanced High-Performance Bus (AHB)
252
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 10: Run-Mode Clock Configuration 2 (RCC2), offset 0x070
This register overrides the RCC equivalent register fields, as shown in Table 5-8, when the USERCC2
bit is set, allowing the extended capabilities of the RCC2 register to be used while also providing a
means to be backward-compatible to previous parts. Each RCC2 field that supersedes an RCC
field is located at the same LSB bit position; however, some RCC2 fields are larger than the
corresponding RCC field.
Table 5-8. RCC2 Fields that Override RCC Fields
RCC2 Field...
Overrides RCC Field
SYSDIV2, bits[28:23]
SYSDIV, bits[26:23]
PWRDN2, bit[13]
PWRDN, bit[13]
BYPASS2, bit[11]
BYPASS, bit[11]
OSCSRC2, bits[6:4]
OSCSRC, bits[5:4]
Important: Write the RCC register prior to writing the RCC2 register.
Run-Mode Clock Configuration 2 (RCC2)
Base 0x400F.E000
Offset 0x070
Type RW, reset 0x07C0.6810
31
30
USERCC2 DIV400
Type
Reset
RW
0
RW
0
15
14
reserved
Type
Reset
RO
0
RO
0
29
28
27
26
reserved
25
24
23
SYSDIV2
22
RO
0
RW
0
RW
0
RW
1
RW
1
RW
1
RW
1
RW
1
13
12
11
10
9
8
7
6
PWRDN2 reserved BYPASS2
RW
1
RO
0
reserved
RW
1
RO
0
21
20
19
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31
USERCC2
RW
0
Use RCC2
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
RO
0
RO
0
OSCSRC2
RO
0
18
reserved
SYSDIV2LSB
RW
0
RW
0
reserved
RW
1
RO
0
RO
0
Value Description
30
DIV400
RW
0
0
The RCC register fields are used, and the fields in RCC2 are
ignored.
1
The RCC2 register fields override the RCC register fields.
Divide PLL as 400 MHz versus 200 MHz
This bit, along with the SYSDIV2LSB bit, allows additional frequency
choices.
Value Description
0
Use SYSDIV2 as is and apply to 200 MHz predivided PLL
output. See Table 5-5 on page 218 for programming guidelines.
1
Append the SYSDIV2LSB bit to the SYSDIV2 field to create a
7 bit divisor using the 400 MHz PLL output, see Table
5-6 on page 219.
June 12, 2014
253
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
29
reserved
RO
0x0
28:23
SYSDIV2
RW
0x0F
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
System Clock Divisor 2
Specifies which divisor is used to generate the system clock from either
the PLL output or the oscillator source (depending on how the BYPASS2
bit is configured). SYSDIV2 is used for the divisor when both the
USESYSDIV bit in the RCC register and the USERCC2 bit in this register
are set. See Table 5-5 on page 218 for programming guidelines.
22
SYSDIV2LSB
RW
1
Additional LSB for SYSDIV2
When DIV400 is set, this bit becomes the LSB of SYSDIV2. If DIV400
is clear, this bit is not used. See Table 5-5 on page 218 for programming
guidelines.
This bit can only be set or cleared when DIV400 is set.
21:14
reserved
RO
0x0
13
PWRDN2
RW
1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Power-Down PLL 2
Value Description
0
The PLL operates normally.
1
The PLL is powered down.
12
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
11
BYPASS2
RW
1
PLL Bypass 2
Value Description
0
The system clock is the PLL output clock divided by the divisor
specified by SYSDIV2.
1
The system clock is derived from the OSC source and divided
by the divisor specified by SYSDIV2.
See Table 5-5 on page 218 for programming guidelines.
Note:
10:7
reserved
RO
0x0
The ADC must be clocked from the PLL or directly from a
16-MHz clock source to operate properly.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
254
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
6:4
OSCSRC2
RW
0x1
Description
Oscillator Source 2
Selects the input source for the OSC. The values are:
Value
Description
0x0
MOSC
Main oscillator
0x1
PIOSC
Precision internal oscillator
0x2
PIOSC/4
Precision internal oscillator / 4
0x3
LFIOSC
Low-frequency internal oscillator
0x4-0x6 Reserved
0x7
32.768 kHz
32.768-kHz external oscillator
3:0
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
255
Texas Instruments-Production Data
System Control
Register 11: Main Oscillator Control (MOSCCTL), offset 0x07C
This register provides control over the features of the main oscillator, including the ability to enable
the MOSC clock verification circuit, what action to take when the MOSC fails, and whether or not a
crystal is connected. When enabled, this circuit monitors the frequency of the MOSC to verify that
the oscillator is operating within specified limits. If the clock goes invalid after being enabled, the
microcontroller issues a power-on reset and reboots to the NMI handler or generates an interrupt.
Main Oscillator Control (MOSCCTL)
Base 0x400F.E000
Offset 0x07C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
31:3
reserved
RO
0x0000.000
2
NOXTAL
RW
0
NOXTAL MOSCIM
RW
0
RW
0
CVAL
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
No Crystal Connected
Value Description
1
MOSCIM
RW
0
0
This bit should be cleared when a crystal or oscillator is
connected to the OSC0 and OSC1 inputs, regardless of whether
or not the MOSC is used or powered down.
1
This bit should be set when a crystal or external oscillator is not
connected to the OSC0 and OSC1 inputs to reduce power
consumption.
MOSC Failure Action
Value Description
0
If the MOSC fails, a MOSC failure reset is generated and reboots
to the NMI handler.
1
If the MOSC fails, an interrupt is generated as indicated by the
MOFRIS bit in the RIS register..
Regardless of the action taken, if the MOSC fails, the oscillator source
is switched to the PIOSC automatically.
0
CVAL
RW
0
Clock Validation for MOSC
Value Description
0
The MOSC monitor circuit is disabled.
1
The MOSC monitor circuit is enabled.
256
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 12: Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144
This register provides configuration information for the hardware control of Deep Sleep Mode.
Deep Sleep Clock Configuration (DSLPCLKCFG)
Base 0x400F.E000
Offset 0x144
Type RW, reset 0x0780.0000
31
30
29
28
27
26
reserved
Type
Reset
25
24
23
22
21
20
DSDIVORIDE
18
17
16
reserved
RO
0
RO
0
RO
0
RW
0
RW
0
RW
1
RW
1
RW
1
RW
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RO
0
reserved
Type
Reset
19
DSOSCSRC
RO
0
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0x0
28:23
DSDIVORIDE
RW
0x0F
RW
0
reserved
RO
0
PIOSCPD reserved
RW
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Divider Field Override
If Deep-Sleep mode is enabled when the PLL is running, the PLL is
disabled. This 6-bit field contains a system divider field that overrides
the SYSDIV field in the RCC register or the SYSDIV2 field in the RCC2
register during Deep Sleep. This divider is applied to the source selected
by the DSOSCSRC field.
Value Description
0x0
/1
0x1
/2
0x2
/3
0x3
/4
...
...
0x3F /64
22:7
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
257
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
6:4
DSOSCSRC
RW
0x0
Description
Clock Source
Specifies the clock source during Deep-Sleep mode.
Value
Description
0x0
MOSC
Use the main oscillator as the source. To use the MOSC as
the Deep-Sleep mode clock source, the MOSC must also be
configured as the Run mode clock source in the Run-Mode
Clock Configuration (RCC) register.
Note:
0x1
If the PIOSC is being used as the clock reference
for the PLL, the PIOSC is the clock source instead
of MOSC in Deep-Sleep mode.
PIOSC
Use the precision internal 16-MHz oscillator as the source.
0x2
Reserved
0x3
LFIOSC
Use the low-frequency internal oscillator as the source.
0x4-0x6 Reserved
0x7
32.768 kHz
Use the Hibernation module 32.768-kHz external oscillator
as the source.
3:2
reserved
RO
0x0
1
PIOSCPD
RW
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PIOSC Power Down Request
Allows software to request the PIOSC to be powered-down in
Deep-Sleep mode. If the PIOSC is needed by an enabled peripheral
during Deep-Sleep, the PIOSC is powered down, but a warning is
generated using the PPDW bit in the SDPMST register. If it is not possible
to power down the PIOSC, an error is reported using the PPDERR bit in
the SDPMST register.
This bit can only be used to power down the PIOSC when the PIOSCPDE
bit in the SYSPROP register is set.
Value Description
0
reserved
RO
0
0
No action.
1
Software requests that the PIOSC is powered down during
Deep-Sleep mode.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
258
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 13: System Properties (SYSPROP), offset 0x14C
This register provides information on whether certain System Control properties are present on the
microcontroller.
System Properties (SYSPROP)
Base 0x400F.E000
Offset 0x14C
Type RO, reset 0x0000.1D31
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
1
RO
1
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
PIOSCPDE
RO
0
RO
1
SRAMSM SRAMLPM reserved FLASHLPM
RO
1
RO
1
RO
0
RO
1
reserved
RO
0
reserved
reserved
RO
0
FPU
RO
0
RO
1
Bit/Field
Name
Type
Reset
Description
31:13
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
12
PIOSCPDE
RO
0x1
PIOSC Power Down Present
This bit determines whether the PIOSCPD bit in the DSLPCLKCFG
register can be set to power down the PIOSC in Deep-Sleep mode.
Value Description
11
SRAMSM
RO
0x1
0
The status of the PIOSCPD bit is ignored.
1
The PIOSCPD bit can be set to power down the PIOSC in
Deep-Sleep mode.
SRAM Sleep/Deep-Sleep Standby Mode Present
This bit determines whether the SRAMPM field in the SLPPWRCFG and
DSLPPWRCFG registers can be configured to put the SRAM into
Standby mode while in Sleep or Deep-Sleep mode.
Value Description
10
SRAMLPM
RO
0x1
0
A value of 0x1 in the SRAMPM fields is ignored.
1
The SRAMPM fields can be configured to put the SRAM into
Standby mode while in Sleep or Deep-Sleep mode.
SRAM Sleep/Deep-Sleep Low Power Mode Present
This bit determines whether the SRAMPM field in the SLPPWRCFG and
DSLPPWRCFG registers can be configured to put the SRAM into Low
Power mode while in Sleep or Deep-Sleep mode.
Value Description
0
A value of 0x3 in the SRAMPM fields is ignored.
1
The SRAMPM fields can be configured to put the SRAM into Low
Power mode while in Sleep or Deep-Sleep mode.
June 12, 2014
259
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
9
reserved
RO
0
8
FLASHLPM
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Flash Memory Sleep/Deep-Sleep Low Power Mode Present
This bit determines whether the FLASHPM field in the SLPPWRCFG
and DSLPPWRCFG registers can be configured to put the Flash memory
into Low Power mode while in Sleep or Deep-Sleep mode.
Value Description
0
A value of 0x2 in the FLASHPM fields is ignored.
1
The FLASHPM fields can be configured to put the Flash memory
into Low Power mode while in Sleep or Deep-Sleep mode.
7:6
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5:4
reserved
RO
0x3
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
FPU
RO
0x1
FPU Present
This bit indicates if the FPU is present in the Cortex-M4 core.
Value Description
0
FPU is not present.
1
FPU is present.
260
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 14: Precision Internal Oscillator Calibration (PIOSCCAL), offset 0x150
This register provides the ability to update or recalibrate the precision internal oscillator. Note that
a 32.768-kHz oscillator must be used as the Hibernation module clock source for the user to be
able to calibrate the PIOSC.
Precision Internal Oscillator Calibration (PIOSCCAL)
Base 0x400F.E000
Offset 0x150
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
UTEN
Type
Reset
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
reserved
reserved
Type
Reset
23
RO
0
CAL
RW
0
Bit/Field
Name
Type
Reset
31
UTEN
RW
0
UPDATE reserved
RW
0
RO
0
UT
Description
Use User Trim Value
Value Description
30:10
reserved
RO
0x0000
9
CAL
RW
0
0
The factory calibration value is used for an update trim operation.
1
The trim value in bits[6:0] of this register are used for any update
trim operation.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Start Calibration
Value Description
0
No action.
1
Starts a new calibration of the PIOSC. Results are in the
PIOSCSTAT register. The resulting trim value from the operation
is active in the PIOSC after the calibration completes. The result
overrides any previous update trim operation whether the
calibration passes or fails.
This bit is auto-cleared after it is set.
8
UPDATE
RW
0
Update Trim
Value Description
0
No action.
1
Updates the PIOSC trim value with the UT bit or the DT bit in
the PIOSCSTAT register. Used with UTEN.
This bit is auto-cleared after the update.
7
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
261
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
6:0
UT
RW
0x0
Description
User Trim Value
User trim value that can be loaded into the PIOSC.
Refer to “Precision Internal Oscillator Operation (PIOSC)” on page 219
for more information on calibrating the PIOSC.
262
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 15: Precision Internal Oscillator Statistics (PIOSCSTAT), offset 0x154
This register provides the user information on the PIOSC calibration. Note that a 32.768-kHz oscillator
must be used as the Hibernation module clock source for the user to be able to calibrate the PIOSC.
Precision Internal Oscillator Statistics (PIOSCSTAT)
Base 0x400F.E000
Offset 0x154
Type RO, reset 0x0000.0040
31
30
29
28
RO
0
RO
0
RO
0
RO
0
15
14
13
12
RO
0
RO
0
RO
0
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
RO
-
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
DT
reserved
Type
Reset
RO
0
RESULT
reserved
RO
0
RO
0
CT
Bit/Field
Name
Type
Reset
Description
31:23
reserved
RO
0x00
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
22:16
DT
RO
-
Default Trim Value
This field contains the default trim value. This value is loaded into the
PIOSC after every full power-up.
15:10
reserved
RO
0x0
9:8
RESULT
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Calibration Result
Value Description
7
reserved
RO
0
6:0
CT
RO
0x40
0x0
Calibration has not been attempted.
0x1
The last calibration operation completed to meet 1% accuracy.
0x2
The last calibration operation failed to meet 1% accuracy.
0x3
Reserved
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Calibration Trim Value
This field contains the trim value from the last calibration operation. After
factory calibration CT and DT are the same.
June 12, 2014
263
Texas Instruments-Production Data
System Control
Register 16: PLL Frequency 0 (PLLFREQ0), offset 0x160
This register always contains the current M value presented to the system PLL.
The PLL frequency can be calculated using the following equation:
PLL frequency = (XTAL frequency * MDIV) / ((Q + 1) * (N + 1))
where
MDIV = MINT + (MFRAC / 1024)
The Q and N values are shown in the PLLFREQ1 register. Table 23-14 on page 1242 shows the M,
Q, and N values as well as the resulting PLL frequency for the various XTAL configurations.
PLL Frequency 0 (PLLFREQ0)
Base 0x400F.E000
Offset 0x160
Type RO, reset 0x0000.0032
31
30
29
28
27
26
25
24
23
22
21
20
19
18
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
MFRAC
Type
Reset
RO
1
RO
1
RO
0
RO
0
17
16
MFRAC
RO
0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
MINT
RO
1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:20
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
19:10
MFRAC
RO
0x32
PLL M Fractional Value
This field contains the integer value of the PLL M value.
9:0
MINT
RO
0x00
PLL M Integer Value
This field contains the integer value of the PLL M value.
264
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 17: PLL Frequency 1 (PLLFREQ1), offset 0x164
This register always contains the current Q and N values presented to the system PLL.
The M value is shown in the PLLFREQ0 register. Table 23-14 on page 1242 shows the M, Q, and N
values as well as the resulting PLL frequency for the various XTAL configurations.
PLL Frequency 1 (PLLFREQ1)
Base 0x400F.E000
Offset 0x164
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
6
5
4
3
2
1
0
RO
0
RO
1
reserved
Type
Reset
RO
0
15
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
14
13
12
11
10
9
8
7
reserved
Type
Reset
RO
0
RO
0
Q
RO
0
RO
0
RO
0
RO
0
reserved
RO
0
Bit/Field
Name
Type
Reset
31:13
reserved
RO
0x0000.0
12:8
Q
RO
0x0
RO
0
RO
0
RO
0
N
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PLL Q Value
This field contains the PLL Q value.
7:5
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
4:0
N
RO
0x1
PLL N Value
This field contains the PLL N value.
June 12, 2014
265
Texas Instruments-Production Data
System Control
Register 18: PLL Status (PLLSTAT), offset 0x168
This register shows the direct status of the PLL lock.
PLL Status (PLLSTAT)
Base 0x400F.E000
Offset 0x168
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0x0000.000
0
LOCK
RO
0x0
RO
0
LOCK
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PLL Lock
Value Description
0
The PLL is unpowered or is not yet locked.
1
The PLL is powered and locked.
266
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 19: Sleep Power Configuration (SLPPWRCFG), offset 0x188
This register provides configuration information for the power control of the SRAM and Flash memory
while in Sleep mode.
Sleep Power Configuration (SLPPWRCFG)
Base 0x400F.E000
Offset 0x188
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RW
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
FLASHPM
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.00
5:4
FLASHPM
RW
0x0
RW
0
reserved
RO
0
SRAMPM
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Flash Power Modes
Value Description
0x0
Active Mode
Flash memory is not placed in a lower power mode. This mode
provides the fastest time to sleep and wakeup but the highest
power consumption while the microcontroller is in Sleep mode.
0x1
Reserved
0x2
Low Power Mode
Flash memory is placed in low power mode. This mode provides
the lowers power consumption but requires more time to come
out of Sleep mode.
0x3
3:2
reserved
RO
0x0
Reserved
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
267
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1:0
SRAMPM
RW
0x0
Description
SRAM Power Modes
This field controls the low power modes of the on-chip SRAM while the
microcontroller is in Deep-Sleep mode.
Value Description
0x0
Active Mode
SRAM is not placed in a lower power mode. This mode provides
the fastest time to sleep and wakeup but the highest power
consumption while the microcontroller is in Sleep mode.
0x1
Standby Mode
SRAM is place in standby mode while in Sleep mode.
0x2
Reserved
0x3
Low Power Mode
SRAM is placed in low power mode. This mode provides the
slowest time to sleep and wakeup but the lowest power
consumption while in Sleep mode.
268
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 20: Deep-Sleep Power Configuration (DSLPPWRCFG), offset 0x18C
This register provides configuration information for the power control of the SRAM and Flash memory
while in Deep-Sleep mode.
Deep-Sleep Power Configuration (DSLPPWRCFG)
Base 0x400F.E000
Offset 0x18C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RW
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
FLASHPM
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.00
5:4
FLASHPM
RW
0x0
RW
0
reserved
RO
0
SRAMPM
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Flash Power Modes
Value Description
0x0
Active Mode
Flash memory is not placed in a lower power mode. This mode
provides the fastest time to sleep and wakeup but the highest
power consumption while the microcontroller is in Deep-Sleep
mode.
0x1
Reserved
0x2
Low Power Mode
Flash memory is placed in low power mode. This mode provides
the lowers power consumption but requires more time to come
out of Deep-Sleep mode.
0x3
3:2
reserved
RO
0x0
Reserved
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
269
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1:0
SRAMPM
RW
0x0
Description
SRAM Power Modes
This field controls the low power modes of the on-chip SRAM while the
microcontroller is in Deep-Sleep mode.
Value Description
0x0
Active Mode
SRAM is not placed in a lower power mode. This mode provides
the fastest time to sleep and wakeup but the highest power
consumption while the microcontroller is in Deep-Sleep mode.
0x1
Standby Mode
SRAM is place in standby mode while in Deep-Sleep mode.
0x2
Reserved
0x3
Low Power Mode
SRAM is placed in low power mode. This mode provides the
slowest time to sleep and wakeup but the lowest power
consumption while in Deep-Sleep mode.
270
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 21: LDO Sleep Power Control (LDOSPCTL), offset 0x1B4
This register specifies the LDO output voltage while in Sleep mode. Writes to the VLDO bit field have
no effect on the LDO output voltage, regardless of what is specified for the VADJEN bit. The LDO
output voltage is fixed at the recommended factory reset value.
The table below shows the maximum system clock frequency and PIOSC frequency with respect
to the configured LDO voltage.
Operating Voltage (LDO)
Maximum System Clock Frequency
PIOSC
1.2
80 MHz
16 MHz
0.9
20 MHz
16 MHz
Note:
■ The LDO will not automatically adjust in Sleep/Deepsleep mode if a debugger has been
connected since the last power-on reset.
■ If the LDO voltage is adjusted, it will take an extra 4 us to wake up from Sleep or
Deep-Sleep mode.
LDO Sleep Power Control (LDOSPCTL)
Base 0x400F.E000
Offset 0x1B4
Type RW, reset 0x0000.0018
31
30
29
28
27
26
25
24
22
21
20
19
18
17
16
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
1
RW
1
RW
0
RW
0
RW
0
VADJEN
Type
Reset
23
reserved
reserved
Type
Reset
VLDO
RO
0
Bit/Field
Name
Type
Reset
31
VADJEN
RW
0
Description
Voltage Adjust Enable
This bit enables the value of the VLDO field to be used to specify the
output voltage of the LDO in Sleep mode.
Value Description
30:8
reserved
RO
0x000.00
0
The LDO output voltage is set to the factory default value in
Sleep mode. The value of the VLDO field does not affect the
LDO operation.
1
The LDO output value in Sleep mode is configured by the value
in the VLDO field.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
271
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
7:0
VLDO
RW
0x18
LDO Output Voltage
This field provides program control of the LDO output voltage in Run
mode. The value of the field is only used for the LDO voltage when the
VADJEN bit is set.
For lowest power in Sleep mode, it is recommended to configure an
LDO output voltage that is equal to or lower than the default value of
1.2 V.
Value
Description
0x12
0.90 V
0x13
0.95 V
0x14
1.00 V
0x15
1.05 V
0x16
1.10 V
0x17
1.15 V
0x18
1.20 V
0x19 - 0xFF reserved
272
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 22: LDO Sleep Power Calibration (LDOSPCAL), offset 0x1B8
This register provides factory determined values that are recommended for the VLDO field in the
LDOSPCTL register while in Sleep mode.
LDO Sleep Power Calibration (LDOSPCAL)
Base 0x400F.E000
Offset 0x1B8
Type RO, reset 0x0000.1818
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
0
reserved
Type
Reset
WITHPLL
Type
Reset
NOPLL
RO
1
Bit/Field
Name
Type
Reset
Description
31:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:8
WITHPLL
RO
0x18
Sleep with PLL
The value in this field is the suggested value for the VLDO field in the
LDOSPCTL register when using the PLL. This value provides the lowest
recommended LDO output voltage for use with the PLL at the maximum
specified value.
7:0
NOPLL
RO
0x18
Sleep without PLL
The value in this field is the suggested value for the VLDO field in the
LDOSPCTL register when not using the PLL. This value provides the
lowest recommended LDO output voltage for use without the PLL.
June 12, 2014
273
Texas Instruments-Production Data
System Control
Register 23: LDO Deep-Sleep Power Control (LDODPCTL), offset 0x1BC
This register specifies the LDO output voltage while in Deep-Sleep mode. This register must be
configured in Run mode before entering Deep-Sleep. Writes to the VLDO bit field have no effect on
the LDO output voltage, regardless of what is specified for the VADJEN bit. The LDO output voltage
is fixed at the recommended factory reset value.
The table below shows the maximum system clock frequency and PIOSC frequency with respect
to the configured LDO voltage.
Operating Voltage (LDO)
Maximum System Clock Frequency
PIOSC
1.2
80 MHz
16 MHz
0.9
20 MHz
16 MHz
Note:
■ The LDO will not automatically adjust in Sleep/Deepsleep mode if a debugger has been
connected since the last power-on reset.
■ If the LDO voltage is adjusted, it will take an extra 4 us to wake up from Sleep or
Deep-Sleep mode.
LDO Deep-Sleep Power Control (LDODPCTL)
Base 0x400F.E000
Offset 0x1BC
Type RW, reset 0x0000.0012
31
30
29
28
27
26
25
24
22
21
20
19
18
17
16
RW
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
1
RW
0
RW
0
RW
1
RW
0
VADJEN
Type
Reset
23
reserved
reserved
Type
Reset
VLDO
RO
0
Bit/Field
Name
Type
Reset
31
VADJEN
RW
0
Description
Voltage Adjust Enable
This bit enables the value of the VLDO field to be used to specify the
output voltage of the LDO in Deep-Sleep mode.
Value Description
30:8
reserved
RO
0x000.00
0
The LDO output voltage is set to the factory default value in
Deep-Sleep mode. The value of the VLDO field does not affect
the LDO operation.
1
The LDO output value in Deep-Sleep mode is configured by the
value in the VLDO field.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
274
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
Description
7:0
VLDO
RW
0x12
LDO Output Voltage
This field provides program control of the LDO output voltage in Run
mode. The value of the field is only used for the LDO voltage when the
VADJEN bit is set.
For lowest power in Deep-Sleep mode, it is recommended to configure
the LDO output voltage to the default value of 0.90 V.
Value
Description
0x12
0.90 V
0x13
0.95 V
0x14
1.00 V
0x15
1.05 V
0x16
1.10 V
0x17
1.15 V
0x18
1.20 V
0x19 - 0xFF reserved
June 12, 2014
275
Texas Instruments-Production Data
System Control
Register 24: LDO Deep-Sleep Power Calibration (LDODPCAL), offset 0x1C0
This register provides factory determined values that are recommended for the VLDO field in the
LDODPCTL register while in Deep-Sleep mode.
LDO Deep-Sleep Power Calibration (LDODPCAL)
Base 0x400F.E000
Offset 0x1C0
Type RO, reset 0x0000.1212
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
1
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
RO
1
RO
0
reserved
Type
Reset
NOPLL
Type
Reset
30KHZ
Bit/Field
Name
Type
Reset
Description
31:16
reserved
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
15:8
NOPLL
RO
0x12
Deep-Sleep without PLL
The value in this field is the suggested value for the VLDO field in the
LDODPCTL register when not using the PLL. This value provides the
lowest recommended LDO output voltage for use with the system clock.
7:0
30KHZ
RO
0x12
Deep-Sleep with IOSC
The value in this field is the suggested value for the VLDO field in the
LDODPCTL register when not using the PLL. This value provides the
lowest recommended LDO output voltage for use with the low-frequency
internal oscillator.
276
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 25: Sleep / Deep-Sleep Power Mode Status (SDPMST), offset 0x1CC
This register provides status information on the Sleep and Deep-Sleep power modes as well as
some real time status that can be viewed by a debugger or the core if it is running. These events
do not trigger an interrupt and are meant to provide information that can help tune software for power
management. The status register gets written at the beginning of every Dynamic Power Management
event request with the results of any error checking. There is no mechanism to clear the bits; they
are overwritten on the next event. The LDOUA, FLASHLP, LOWPWR, PRACT bits provide real time
data and there are no events to register that information.
Sleep / Deep-Sleep Power Mode Status (SDPMST)
Base 0x400F.E000
Offset 0x1CC
Type RO, reset 0x0000.0000
31
30
29
28
27
26
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
RO
0
RO
0
RO
0
RO
0
25
24
23
22
21
20
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
reserved
Type
Reset
PPDW
RO
0
18
17
16
LDOUA FLASHLP LOWPWR PRACT
reserved
Type
Reset
19
RO
0
LMAXERR reserved LSMINERR LDMINERR PPDERR FPDERR SPDERR
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:20
reserved
RO
0x000
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
19
LDOUA
RO
0
LDO Update Active
Value Description
18
FLASHLP
RO
0
0
The LDO voltage level is not changing.
1
The LDO voltage level is changing.
Flash Memory in Low Power State
Value Description
17
LOWPWR
RO
0
0
The Flash memory is currently in the active state.
1
The Flash memory is currently in the low power state as
programmed in the SLPPWRCFG or DSLPPWRCFG register.
Sleep or Deep-Sleep Mode
Value Description
0
The microcontroller is currently in Run mode.
1
The microcontroller is currently in Sleep or Deep-Sleep mode
and is waiting for an interrupt or is in the process of powering
up. The status of this bit is not affected by the power state of
the Flash memory or SRAM.
June 12, 2014
277
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
16
PRACT
RO
0
Description
Sleep or Deep-Sleep Power Request Active
Value Description
15:8
reserved
RO
0x00
7
PPDW
RO
0
0
A power request is not active.
1
The microcontroller is currently in Deep-Sleep mode or is in
Sleep mode and a request to put the SRAM and/or Flash
memory into a lower power mode is currently active as
configured by the SLPPWRCFG register.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PIOSC Power Down Request Warning
Value Description
6
LMAXERR
RO
0
0
No error.
1
A warning has occurred because software has requested that
the PIOSC be powered down during Deep-Sleep using the
PIOSCPD bit in the DSLPCLKCFG register and a peripheral
requires that it be active in Deep-Sleep. The PIOSC is powered
down regardless of the warning.
VLDO Value Above Maximum Error
Value Description
0
No error.
1
An error has occurred because software has requested that the
LDO voltage be above the maximum value allowed using the
VLDO bit in the LDOSPCTL or LDODPCTL register.
In this situation, the LDO is set to the factory default value.
5
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
4
LSMINERR
RO
0
VLDO Value Below Minimum Error in Sleep Mode
Value Description
0
No error.
1
An error has occurred because software has requested that the
LDO voltage be below the minimum value allowed using the
VLDO bit in the LDOSPCTL register.
In this situation, the LDO voltage is not changed when entering
Sleep mode.
278
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
LDMINERR
RO
0
Description
VLDO Value Below Minimum Error in Deep-Sleep Mode
Value Description
0
No error.
1
An error has occurred because software has requested that the
LDO voltage be below the minimum value allowed using the
VLDO bit in the LDODPCTL register.
In this situation, the LDO voltage is not changed when entering
Deep-Sleep mode.
2
PPDERR
RO
0
PIOSC Power Down Request Error
Value Description
0
No error.
1
An error has occurred because software has requested that the
PIOSC be powered down during Deep-Sleep and it is not
possible to power down the PIOSC.
In this situation, the PIOSC is not powered down when entering
Deep-Sleep mode.
1
FPDERR
RO
0
Flash Memory Power Down Request Error
Value Description
0
SPDERR
RO
0
0
No error.
1
An error has occurred because software has requested a Flash
memory power down mode that is not available using the
FLASHPM field in the SLPPWRCFG or the DSLPPWRCFG
register.
SRAM Power Down Request Error
Value Description
0
No error.
1
An error has occurred because software has requested an
SRAM power down mode that is not available using the SRAMPM
field in the SLPPWRCFG or the DSLPPWRCFG register.
June 12, 2014
279
Texas Instruments-Production Data
System Control
Register 26: Watchdog Timer Peripheral Present (PPWD), offset 0x300
The PPWD register provides software information regarding the watchdog modules.
Important: This register should be used to determine which watchdog timers are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if a legacy module is present.
Watchdog Timer Peripheral Present (PPWD)
Base 0x400F.E000
Offset 0x300
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Watchdog Timer 1 Present
Value Description
0
P0
RO
0x1
0
Watchdog module 1 is not present.
1
Watchdog module 1 is present.
Watchdog Timer 0 Present
Value Description
0
Watchdog module 0 is not present.
1
Watchdog module 0 is present.
280
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 27: 16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER),
offset 0x304
The PPTIMER register provides software information regarding the 16/32-bit general-purpose timer
modules.
Important: This register should be used to determine which timers are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy module is present. Software must
use this register to determine if a module that is not supported by the DC2 register is
present.
16/32-Bit General-Purpose Timer Peripheral Present (PPTIMER)
Base 0x400F.E000
Offset 0x304
Type RO, reset 0x0000.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0
5
P5
RO
0x1
RO
0
RO
0
RO
0
5
4
3
2
1
0
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
16/32-Bit General-Purpose Timer 5 Present
Value Description
4
P4
RO
0x1
0
16/32-bit general-purpose timer module 6 is not present.
1
16/32-bit general-purpose timer module 5 is present.
16/32-Bit General-Purpose Timer 4 Present
Value Description
3
P3
RO
0x1
0
16/32-bit general-purpose timer module 4 is not present.
1
16/32-bit general-purpose timer module 4 is present.
16/32-Bit General-Purpose Timer 3 Present
Value Description
0
16/32-bit general-purpose timer module 3 is not present.
1
16/32-bit general-purpose timer module 3 is present.
June 12, 2014
281
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
P2
RO
0x1
Description
16/32-Bit General-Purpose Timer 2 Present
Value Description
1
P1
RO
0x1
0
16/32-bit general-purpose timer module 2 is not present.
1
16/32-bit general-purpose timer module 2 is present.
16/32-Bit General-Purpose Timer 1 Present
Value Description
0
P0
RO
0x1
0
16/32-bit general-purpose timer module 1 is not present.
1
16/32-bit general-purpose timer module 1 is present.
16/32-Bit General-Purpose Timer 0 Present
Value Description
0
16/32-bit general-purpose timer module 0 is not present.
1
16/32-bit general-purpose timer module 0 is present.
282
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 28: General-Purpose Input/Output Peripheral Present (PPGPIO),
offset 0x308
The PPGPIO register provides software information regarding the general-purpose input/output
modules.
Important: This register should be used to determine which GPIO ports are implemented on this
microcontroller. However, to support legacy software, the DC4 register is available. A
read of the DC4 register correctly identifies if a legacy module is present. Software must
use this register to determine if a module that is not supported by the DC4 register is
present.
General-Purpose Input/Output Peripheral Present (PPGPIO)
Base 0x400F.E000
Offset 0x308
Type RO, reset 0x0000.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
reserved
P14
P13
P12
P11
P10
P9
P8
P7
P6
P5
P4
P3
P2
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31:15
reserved
RO
0
14
P14
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
GPIO Port Q Present
Value Description
13
P13
RO
0x0
0
GPIO Port Q is not present.
1
GPIO Port Q is present.
GPIO Port P Present
Value Description
12
P12
RO
0x0
0
GPIO Port P is not present.
1
GPIO Port P is present.
GPIO Port N Present
Value Description
0
GPIO Port N is not present.
1
GPIO Port N is present.
June 12, 2014
283
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
11
P11
RO
0x0
Description
GPIO Port M Present
Value Description
10
P10
RO
0x0
0
GPIO Port M is not present.
1
GPIO Port M is present.
GPIO Port L Present
Value Description
9
P9
RO
0x0
0
GPIO Port L is not present.
1
GPIO Port L is present.
GPIO Port K Present
Value Description
8
P8
RO
0x0
0
GPIO Port K is not present.
1
GPIO Port K is present.
GPIO Port J Present
Value Description
7
P7
RO
0x0
0
GPIO Port J is not present.
1
GPIO Port J is present.
GPIO Port H Present
Value Description
6
P6
RO
0x0
0
GPIO Port H is not present.
1
GPIO Port H is present.
GPIO Port G Present
Value Description
5
P5
RO
0x1
0
GPIO Port G is not present.
1
GPIO Port G is present.
GPIO Port F Present
Value Description
0
GPIO Port F is not present.
1
GPIO Port F is present.
284
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
4
P4
RO
0x1
Description
GPIO Port E Present
Value Description
3
P3
RO
0x1
0
GPIO Port E is not present.
1
GPIO Port E is present.
GPIO Port D Present
Value Description
2
P2
RO
0x1
0
GPIO Port D is not present.
1
GPIO Port D is present.
GPIO Port C Present
Value Description
1
P1
RO
0x1
0
GPIO Port C is not present.
1
GPIO Port C is present.
GPIO Port B Present
Value Description
0
P0
RO
0x1
0
GPIO Port B is not present.
1
GPIO Port B is present.
GPIO Port A Present
Value Description
0
GPIO Port A is not present.
1
GPIO Port A is present.
June 12, 2014
285
Texas Instruments-Production Data
System Control
Register 29: Micro Direct Memory Access Peripheral Present (PPDMA), offset
0x30C
The PPDMA register provides software information regarding the μDMA module.
Important: This register should be used to determine if the μDMA module is implemented on this
microcontroller. However, to support legacy software, the DC7 register is available. A
read of the DC7 register correctly identifies if the μDMA module is present.
Micro Direct Memory Access Peripheral Present (PPDMA)
Base 0x400F.E000
Offset 0x30C
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
0
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
μDMA Module Present
Value Description
0
μDMA module is not present.
1
μDMA module is present.
286
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 30: Hibernation Peripheral Present (PPHIB), offset 0x314
The PPHIB register provides software information regarding the Hibernation module.
Important: This register should be used to determine if the Hibernation module is implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if the Hibernation module is present.
Hibernation Peripheral Present (PPHIB)
Base 0x400F.E000
Offset 0x314
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
P0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Hibernation Module Present
Value Description
0
Hibernation module is not present.
1
Hibernation module is present.
June 12, 2014
287
Texas Instruments-Production Data
System Control
Register 31: Universal Asynchronous Receiver/Transmitter Peripheral Present
(PPUART), offset 0x318
The PPUART register provides software information regarding the UART modules.
Important: This register should be used to determine which UART modules are implemented on
this microcontroller. However, to support legacy software, the DC2 register is available.
A read of the DC2 register correctly identifies if a legacy UART module is present.
Software must use this register to determine if a module that is not supported by the
DC2 register is present.
Universal Asynchronous Receiver/Transmitter Peripheral Present (PPUART)
Base 0x400F.E000
Offset 0x318
Type RO, reset 0x0000.00FF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:8
reserved
RO
0
7
P7
RO
0x1
RO
0
RO
0
7
6
5
4
3
2
1
0
P7
P6
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART Module 7 Present
Value Description
6
P6
RO
0x1
0
UART module 7 is not present.
1
UART module 7 is present.
UART Module 6 Present
Value Description
5
P5
RO
0x1
0
UART module 6 is not present.
1
UART module 6 is present.
UART Module 5 Present
Value Description
0
UART module 5 is not present.
1
UART module 5 is present.
288
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
4
P4
RO
0x1
Description
UART Module 4 Present
Value Description
3
P3
RO
0x1
0
UART module 4 is not present.
1
UART module 4 is present.
UART Module 3 Present
Value Description
2
P2
RO
0x1
0
UART module 3 is not present.
1
UART module 3 is present.
UART Module 2 Present
Value Description
1
P1
RO
0x1
0
UART module 2 is not present.
1
UART module 2 is present.
UART Module 1 Present
Value Description
0
P0
RO
0x1
0
UART module 1 is not present.
1
UART module 1 is present.
UART Module 0 Present
Value Description
0
UART module 0 is not present.
1
UART module 0 is present.
June 12, 2014
289
Texas Instruments-Production Data
System Control
Register 32: Synchronous Serial Interface Peripheral Present (PPSSI), offset
0x31C
The PPSSI register provides software information regarding the SSI modules.
Important: This register should be used to determine which SSI modules are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy SSI module is present. Software
must use this register to determine if a module that is not supported by the DC2 register
is present.
Synchronous Serial Interface Peripheral Present (PPSSI)
Base 0x400F.E000
Offset 0x31C
Type RO, reset 0x0000.000F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:4
reserved
RO
0
3
P3
RO
0x1
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI Module 3 Present
Value Description
2
P2
RO
0x1
0
SSI module 3 is not present.
1
SSI module 3 is present.
SSI Module 2 Present
Value Description
1
P1
RO
0x1
0
SSI module 2 is not present.
1
SSI module 2 is present.
SSI Module 1 Present
Value Description
0
SSI module 1 is not present.
1
SSI module 1 is present.
290
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
P0
RO
0x1
Description
SSI Module 0 Present
Value Description
0
SSI module 0 is not present.
1
SSI module 0 is present.
June 12, 2014
291
Texas Instruments-Production Data
System Control
Register 33: Inter-Integrated Circuit Peripheral Present (PPI2C), offset 0x320
The PPI2C register provides software information regarding the I2C modules.
Important: This register should be used to determine which I2C modules are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy I2C module is present. Software
must use this register to determine if a module that is not supported by the DC2 register
is present.
Inter-Integrated Circuit Peripheral Present (PPI2C)
Base 0x400F.E000
Offset 0x320
Type RO, reset 0x0000.000F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0
5
P5
RO
0x0
RO
0
RO
0
RO
0
5
4
3
2
1
0
P5
P4
P3
P2
P1
P0
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C Module 5 Present
Value Description
4
P4
RO
0x0
0
I2C module 5 is not present.
1
I2C module 5 is present.
I2C Module 4 Present
Value Description
3
P3
RO
0x1
0
I2C module 4 is not present.
1
I2C module 4 is present.
I2C Module 3 Present
Value Description
0
I2C module 3 is not present.
1
I2C module 3 is present.
292
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
P2
RO
0x1
Description
I2C Module 2 Present
Value Description
1
P1
RO
0x1
0
I2C module 2 is not present.
1
I2C module 2 is present.
I2C Module 1 Present
Value Description
0
P0
RO
0x1
0
I2C module 1 is not present.
1
I2C module 1 is present.
I2C Module 0 Present
Value Description
0
I2C module 0 is not present.
1
I2C module 0 is present.
June 12, 2014
293
Texas Instruments-Production Data
System Control
Register 34: Universal Serial Bus Peripheral Present (PPUSB), offset 0x328
The PPUSB register provides software information regarding the USB module.
Important: This register should be used to determine if the USB module is implemented on this
microcontroller. However, to support legacy software, the DC6 register is available. A
read of the DC6 register correctly identifies if the USB module is present.
Universal Serial Bus Peripheral Present (PPUSB)
Base 0x400F.E000
Offset 0x328
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x0
RO
0
P0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
USB Module Present
Value Description
0
USB module is not present.
1
USB module is present.
294
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 35: Controller Area Network Peripheral Present (PPCAN), offset 0x334
The PPCAN register provides software information regarding the CAN modules.
Important: This register should be used to determine which CAN modules are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if a legacy CAN module is present.
Controller Area Network Peripheral Present (PPCAN)
Base 0x400F.E000
Offset 0x334
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN Module 1 Present
Value Description
0
P0
RO
0x1
0
CAN module 1 is not present.
1
CAN module 1 is present.
CAN Module 0 Present
Value Description
0
CAN module 0 is not present.
1
CAN module 0 is present.
June 12, 2014
295
Texas Instruments-Production Data
System Control
Register 36: Analog-to-Digital Converter Peripheral Present (PPADC), offset
0x338
The PPADC register provides software information regarding the ADC modules.
Important: This register should be used to determine which ADC modules are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if a legacy ADC module is present.
Analog-to-Digital Converter Peripheral Present (PPADC)
Base 0x400F.E000
Offset 0x338
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
P1
P0
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC Module 1 Present
Value Description
0
P0
RO
0x1
0
ADC module 1 is not present.
1
ADC module 1 is present.
ADC Module 0 Present
Value Description
0
ADC module 0 is not present.
1
ADC module 0 is present.
296
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 37: Analog Comparator Peripheral Present (PPACMP), offset 0x33C
The PPACMP register provides software information regarding the analog comparator module.
Important: This register should be used to determine if the analog comparator module is
implemented on this microcontroller. However, to support legacy software, the DC2
register is available. A read of the DC2 register correctly identifies if the analog
comparator module is present.
Note that the Analog Comparator Peripheral Properties (ACMPPP) register indicates
how many analog comparator blocks are included in the module.
Analog Comparator Peripheral Present (PPACMP)
Base 0x400F.E000
Offset 0x33C
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
0
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator Module Present
Value Description
0
Analog comparator module is not present.
1
Analog comparator module is present.
June 12, 2014
297
Texas Instruments-Production Data
System Control
Register 38: Pulse Width Modulator Peripheral Present (PPPWM), offset 0x340
The PPPWM register provides software information regarding the PWM modules.
Important: This register should be used to determine which PWM modules are implemented on
this microcontroller. However, to support legacy software, the DC1 register is available.
A read of the DC1 register correctly identifies if the legacy PWM module is present.
Software must use this register to determine if a module that is not supported by the
DC1 register is present.
Pulse Width Modulator Peripheral Present (PPPWM)
Base 0x400F.E000
Offset 0x340
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
P1
P0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Module 1 Present
Value Description
0
P0
RO
0x1
0
PWM module 1 is not present.
1
PWM module 1 is present.
PWM Module 0 Present
Value Description
0
PWM module 0 is not present.
1
PWM module 0 is present.
298
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 39: Quadrature Encoder Interface Peripheral Present (PPQEI), offset
0x344
The PPQEI register provides software information regarding the QEI modules.
Important: This register should be used to determine which QEI modules are implemented on this
microcontroller. However, to support legacy software, the DC2 register is available. A
read of the DC2 register correctly identifies if a legacy QEI module is present.
Quadrature Encoder Interface Peripheral Present (PPQEI)
Base 0x400F.E000
Offset 0x344
Type RO, reset 0x0000.0003
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:2
reserved
RO
0
1
P1
RO
0x1
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
P1
P0
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI Module 1 Present
Value Description
0
P0
RO
0x1
0
QEI module 1 is not present.
1
QEI module 1 is present.
QEI Module 0 Present
Value Description
0
QEI module 0 is not present.
1
QEI module 0 is present.
June 12, 2014
299
Texas Instruments-Production Data
System Control
Register 40: EEPROM Peripheral Present (PPEEPROM), offset 0x358
The PPEEPROM register provides software information regarding the EEPROM module.
EEPROM Peripheral Present (PPEEPROM)
Base 0x400F.E000
Offset 0x358
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
P0
RO
0x1
RO
0
P0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
EEPROM Module Present
Value Description
0
EEPROM module is not present.
1
EEPROM module is present.
300
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 41: 32/64-Bit Wide General-Purpose Timer Peripheral Present
(PPWTIMER), offset 0x35C
The PPWTIMER register provides software information regarding the 32/64-bit wide general-purpose
timer modules.
32/64-Bit Wide General-Purpose Timer Peripheral Present (PPWTIMER)
Base 0x400F.E000
Offset 0x35C
Type RO, reset 0x0000.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0
5
P5
RO
0x1
RO
0
RO
0
RO
0
5
4
3
2
1
0
P5
P4
P3
P2
P1
P0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
32/64-Bit Wide General-Purpose Timer 5 Present
Value Description
4
P4
RO
0x1
0
32/64-bit wide general-purpose timer module 5 is not present.
1
32/64-bit wide general-purpose timer module 5 is present.
32/64-Bit Wide General-Purpose Timer 4 Present
Value Description
3
P3
RO
0x1
0
32/64-bit wide general-purpose timer module 4 is not present.
1
32/64-bit wide general-purpose timer module 4 is present.
32/64-Bit Wide General-Purpose Timer 3 Present
Value Description
2
P2
RO
0x1
0
32/64-bit wide general-purpose timer module 3 is not present.
1
32/64-bit wide general-purpose timer module 3 is present.
32/64-Bit Wide General-Purpose Timer 2 Present
Value Description
0
32/64-bit wide general-purpose timer module 2 is not present.
1
32/64-bit wide general-purpose timer module 2 is present.
June 12, 2014
301
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1
P1
RO
0x1
Description
32/64-Bit Wide General-Purpose Timer 1 Present
Value Description
0
P0
RO
0x1
0
32/64-bit wide general-purpose timer module 1 is not present.
1
32/64-bit wide general-purpose timer module 1 is present.
32/64-Bit Wide General-Purpose Timer 0 Present
Value Description
0
32/64-bit wide general-purpose timer module 0 is not present.
1
32/64-bit wide general-purpose timer module 0 is present.
302
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 42: Watchdog Timer Software Reset (SRWD), offset 0x500
The SRWD register provides software the capability to reset the available watchdog modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the watchdog modules and has the same bit polarity as the corresponding SRCRn
bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRWD register. While the SRWD bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRWD bit.
There may be latency from the clearing of the SRWD bit to when the peripheral is ready for use.
Software can check the corresponding PRWD bit to be sure.
Important: This register should be used to reset the watchdog modules. To support legacy software,
the SRCR0 register is available. Setting a bit in the SRCR0 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR0 register can
be read back correctly when reading the SRCR0 register. If software uses this register
to reset a legacy peripheral (such as Watchdog 1), the write causes proper operation,
but the value of that bit is not reflected in the SRCR0 register. If software uses both
legacy and peripheral-specific register accesses, the peripheral-specific registers must
be accessed by read-modify-write operations that affect only peripherals that are not
present in the legacy registers. In this manner, both the peripheral-specific and legacy
registers have coherent information.
Watchdog Timer Software Reset (SRWD)
Base 0x400F.E000
Offset 0x500
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
Watchdog Timer 1 Software Reset
Value Description
0
Watchdog module 1 is not reset.
1
Watchdog module 1 is reset.
June 12, 2014
303
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
RW
0
Description
Watchdog Timer 0 Software Reset
Value Description
0
Watchdog module 0 is not reset.
1
Watchdog module 0 is reset.
304
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 43: 16/32-Bit General-Purpose Timer Software Reset (SRTIMER),
offset 0x504
The SRTIMER register provides software the capability to reset the available 16/32-bit timer modules.
This register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the timer modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRTIMER register. While the SRTIMER bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRTIMER bit.
There may be latency from the clearing of the SRTIMER bit to when the peripheral is ready for use.
Software can check the corresponding PRTIMER bit to be sure.
Important: This register should be used to reset the timer modules. To support legacy software,
the SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as Timer 1), the write causes proper operation, but
the value of that bit is not reflected in the SRCR1 register. If software uses both legacy
and peripheral-specific register accesses, the peripheral-specific registers must be
accessed by read-modify-write operations that affect only peripherals that are not present
in the legacy registers. In this manner, both the peripheral-specific and legacy registers
have coherent information.
16/32-Bit General-Purpose Timer Software Reset (SRTIMER)
Base 0x400F.E000
Offset 0x504
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RW
0
16/32-Bit General-Purpose Timer 5 Software Reset
Value Description
0
16/32-bit general-purpose timer module 5 is not reset.
1
16/32-bit general-purpose timer module 5 is reset.
June 12, 2014
305
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
R4
RW
0
Description
16/32-Bit General-Purpose Timer 4 Software Reset
Value Description
3
R3
RW
0
0
16/32-bit general-purpose timer module 4 is not reset.
1
16/32-bit general-purpose timer module 4 is reset.
16/32-Bit General-Purpose Timer 3 Software Reset
Value Description
2
R2
RW
0
0
16/32-bit general-purpose timer module 3 is not reset.
1
16/32-bit general-purpose timer module 3 is reset.
16/32-Bit General-Purpose Timer 2 Software Reset
Value Description
1
R1
RW
0
0
16/32-bit general-purpose timer module 2 is not reset.
1
16/32-bit general-purpose timer module 2 is reset.
16/32-Bit General-Purpose Timer 1 Software Reset
Value Description
0
R0
RW
0
0
16/32-bit general-purpose timer module 1 is not reset.
1
16/32-bit general-purpose timer module 1 is reset.
16/32-Bit General-Purpose Timer 0 Software Reset
Value Description
0
16/32-bit general-purpose timer module 0 is not reset.
1
16/32-bit general-purpose timer module 0 is reset.
306
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 44: General-Purpose Input/Output Software Reset (SRGPIO), offset
0x508
The SRGPIO register provides software the capability to reset the available GPIO modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the GPIO modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRGPIO register. While the SRGPIO bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRGPIO bit.
There may be latency from the clearing of the SRGPIO bit to when the peripheral is ready for use.
Software can check the corresponding PRGPIO bit to be sure.
Important: This register should be used to reset the GPIO modules. To support legacy software,
the SRCR2 register is available. Setting a bit in the SRCR2 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR2 register can
be read back correctly when reading the SRCR2 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as GPIO A), the write causes proper operation, but
the value of that bit is not reflected in the SRCR2 register. If software uses both legacy
and peripheral-specific register accesses, the peripheral-specific registers must be
accessed by read-modify-write operations that affect only peripherals that are not present
in the legacy registers. In this manner, both the peripheral-specific and legacy registers
have coherent information.
General-Purpose Input/Output Software Reset (SRGPIO)
Base 0x400F.E000
Offset 0x508
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RW
0
GPIO Port F Software Reset
Value Description
0
GPIO Port F is not reset.
1
GPIO Port F is reset.
June 12, 2014
307
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
R4
RW
0
Description
GPIO Port E Software Reset
Value Description
3
R3
RW
0
0
GPIO Port E is not reset.
1
GPIO Port E is reset.
GPIO Port D Software Reset
Value Description
2
R2
RW
0
0
GPIO Port D is not reset.
1
GPIO Port D is reset.
GPIO Port C Software Reset
Value Description
1
R1
RW
0
0
GPIO Port C is not reset.
1
GPIO Port C is reset.
GPIO Port B Software Reset
Value Description
0
R0
RW
0
0
GPIO Port B is not reset.
1
GPIO Port B is reset.
GPIO Port A Software Reset
Value Description
0
GPIO Port A is not reset.
1
GPIO Port A is reset.
308
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 45: Micro Direct Memory Access Software Reset (SRDMA), offset
0x50C
The SRDMA register provides software the capability to reset the available μDMA module. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the μDMA module and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRDMA register. While the SRDMA bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRDMA bit.
There may be latency from the clearing of the SRDMA bit to when the peripheral is ready for use.
Software can check the corresponding PRDMA bit to be sure.
Important: This register should be used to reset the μDMA module. To support legacy software,
the SRCR2 register is available. Setting the UDMA bit in the SRCR2 register also resets
the μDMA module. If the UDMA bit is set by writing to the SRCR2 register, it can be read
back correctly when reading the SRCR2 register. If software uses this register to reset
the μDMA module, the write causes proper operation, but the value of the UDMA bit is
not reflected in the SRCR2 register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Micro Direct Memory Access Software Reset (SRDMA)
Base 0x400F.E000
Offset 0x50C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
μDMA Module Software Reset
Value Description
0
μDMA module is not reset.
1
μDMA module is reset.
June 12, 2014
309
Texas Instruments-Production Data
System Control
Register 46: Hibernation Software Reset (SRHIB), offset 0x514
The SRHIB register provides software the capability to reset the available Hibernation module. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the Hibernation module and has the same bit polarity as the corresponding SRCRn
bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRHIB register. While the SRHIB bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRHIB bit.
There may be latency from the clearing of the SRHIB bit to when the peripheral is ready for use.
Software can check the corresponding PRHIB bit to be sure.
Important: This register should be used to reset the Hibernation module. To support legacy software,
the SRCR0 register is available. Setting the HIB bit in the SRCR0 register also resets
the Hibernation module. If the HIB bit is set by writing to the SRCR0 register, it can be
read back correctly when reading the SRCR0 register. If software uses this register to
reset the Hibernation module, the write causes proper operation, but the value of the
HIB bit is not reflected in the SRCR0 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Hibernation Software Reset (SRHIB)
Base 0x400F.E000
Offset 0x514
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
Hibernation Module Software Reset
Value Description
0
Hibernation module is not reset.
1
Hibernation module is reset.
310
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 47: Universal Asynchronous Receiver/Transmitter Software Reset
(SRUART), offset 0x518
The SRUART register provides software the capability to reset the available UART modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the UART modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRUART register. While the SRUART bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRUART bit.
There may be latency from the clearing of the SRUART bit to when the peripheral is ready for use.
Software can check the corresponding PRUART bit to be sure.
Important: This register should be used to reset the UART modules. To support legacy software,
the SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as UART0), the write causes proper operation, but
the value of that bit is not reflected in the SRCR1 register. If software uses both legacy
and peripheral-specific register accesses, the peripheral-specific registers must be
accessed by read-modify-write operations that affect only peripherals that are not present
in the legacy registers. In this manner, both the peripheral-specific and legacy registers
have coherent information.
Universal Asynchronous Receiver/Transmitter Software Reset (SRUART)
Base 0x400F.E000
Offset 0x518
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
R7
R6
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
R7
RW
0
UART Module 7 Software Reset
Value Description
0
UART module 7 is not reset.
1
UART module 7 is reset.
June 12, 2014
311
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
6
R6
RW
0
Description
UART Module 6 Software Reset
Value Description
5
R5
RW
0
0
UART module 6 is not reset.
1
UART module 6 is reset.
UART Module 5 Software Reset
Value Description
4
R4
RW
0
0
UART module 5 is not reset.
1
UART module 5 is reset.
UART Module 4 Software Reset
Value Description
3
R3
RW
0
0
UART module 4 is not reset.
1
UART module 4 is reset.
UART Module 3 Software Reset
Value Description
2
R2
RW
0
0
UART module 3 is not reset.
1
UART module 3 is reset.
UART Module 2 Software Reset
Value Description
1
R1
RW
0
0
UART module 2 is not reset.
1
UART module 2 is reset.
UART Module 1 Software Reset
Value Description
0
R0
RW
0
0
UART module 1 is not reset.
1
UART module 1 is reset.
UART Module 0 Software Reset
Value Description
0
UART module 0 is not reset.
1
UART module 0 is reset.
312
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 48: Synchronous Serial Interface Software Reset (SRSSI), offset
0x51C
The SRSSI register provides software the capability to reset the available SSI modules. This register
provides the same capability as the legacy Software Reset Control n SRCRn registers specifically
for the SSI modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRSSI register. While the SRSSI bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRSSI bit.
There may be latency from the clearing of the SRSSI bit to when the peripheral is ready for use.
Software can check the corresponding PRSSI bit to be sure.
Important: This register should be used to reset the SSI modules. To support legacy software, the
SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as SSI0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Synchronous Serial Interface Software Reset (SRSSI)
Base 0x400F.E000
Offset 0x51C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RW
0
SSI Module 3 Software Reset
Value Description
0
SSI module 3 is not reset.
1
SSI module 3 is reset.
June 12, 2014
313
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RW
0
Description
SSI Module 2 Software Reset
Value Description
1
R1
RW
0
0
SSI module 2 is not reset.
1
SSI module 2 is reset.
SSI Module 1 Software Reset
Value Description
0
R0
RW
0
0
SSI module 1 is not reset.
1
SSI module 1 is reset.
SSI Module 0 Software Reset
Value Description
0
SSI module 0 is not reset.
1
SSI module 0 is reset.
314
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 49: Inter-Integrated Circuit Software Reset (SRI2C), offset 0x520
The SRI2C register provides software the capability to reset the available I2C modules. This register
provides the same capability as the legacy Software Reset Control n SRCRn registers specifically
for the I2C modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRI2C register. While the SRI2C bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRI2C bit.
There may be latency from the clearing of the SRI2C bit to when the peripheral is ready for use.
Software can check the corresponding PRI2C bit to be sure.
Important: This register should be used to reset the I2C modules. To support legacy software, the
SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. Software must use this register
to reset modules that are not present in the legacy registers. If software uses this register
to reset a legacy peripheral (such as I2C0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Inter-Integrated Circuit Software Reset (SRI2C)
Base 0x400F.E000
Offset 0x520
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RW
0
I2C Module 3 Software Reset
Value Description
0
I2C module 3 is not reset.
1
I2C module 3 is reset.
June 12, 2014
315
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RW
0
Description
I2C Module 2 Software Reset
Value Description
1
R1
RW
0
0
I2C module 2 is not reset.
1
I2C module 2 is reset.
I2C Module 1 Software Reset
Value Description
0
R0
RW
0
0
I2C module 1 is not reset.
1
I2C module 1 is reset.
I2C Module 0 Software Reset
Value Description
0
I2C module 0 is not reset.
1
I2C module 0 is reset.
316
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 50: Controller Area Network Software Reset (SRCAN), offset 0x534
The SRCAN register provides software the capability to reset the available CAN modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the CAN modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRCAN register. While the SRCAN bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRCAN bit.
There may be latency from the clearing of the SRCAN bit to when the peripheral is ready for use.
Software can check the corresponding PRCAN bit to be sure.
Important: This register should be used to reset the CAN modules. To support legacy software,
the SRCR0 register is available. Setting a bit in the SRCR0 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR0 register can
be read back correctly when reading the SRCR0 register. If software uses this register
to reset a legacy peripheral (such as CAN0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR0 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Controller Area Network Software Reset (SRCAN)
Base 0x400F.E000
Offset 0x534
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
CAN Module 1 Software Reset
Value Description
0
CAN module 1 is not reset.
1
CAN module 1 is reset.
June 12, 2014
317
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
RW
0
Description
CAN Module 0 Software Reset
Value Description
0
CAN module 0 is not reset.
1
CAN module 0 is reset.
318
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 51: Analog-to-Digital Converter Software Reset (SRADC), offset 0x538
The SRADC register provides software the capability to reset the available ADC modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the ADC modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRADC register. While the SRADC bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRADC bit.
There may be latency from the clearing of the SRADC bit to when the peripheral is ready for use.
Software can check the corresponding PRADC bit to be sure.
Important: This register should be used to reset the ADC modules. To support legacy software,
the SRCR0 register is available. Setting a bit in the SRCR0 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR0 register can
be read back correctly when reading the SRCR0 register. If software uses this register
to reset a legacy peripheral (such as ADC0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR0 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog-to-Digital Converter Software Reset (SRADC)
Base 0x400F.E000
Offset 0x538
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
ADC Module 1 Software Reset
Value Description
0
ADC module 1 is not reset.
1
ADC module 1 is reset.
June 12, 2014
319
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
RW
0
Description
ADC Module 0 Software Reset
Value Description
0
ADC module 0 is not reset.
1
ADC module 0 is reset.
320
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 52: Analog Comparator Software Reset (SRACMP), offset 0x53C
The SRACMP register provides software the capability to reset the available analog comparator
module. This register provides the same capability as the legacy Software Reset Control n SRCRn
registers specifically for the analog comparator module and has the same bit polarity as the
corresponding SRCRn bits.
A block is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRACMP register. While the SRACMP bit is 1, the module
is held in reset.
2. Software completes the reset process by clearing the SRACMP bit.
There may be latency from the clearing of the SRACMP bit to when the module is ready for use.
Software can check the corresponding PRACMP bit to be sure.
Important: This register should be used to reset the analog comparator module. To support legacy
software, the SRCR1 register is available. Setting any of the COMPn bits in the SRCR0
register also resets the analog comparator module. If any of the COMPn bits are set by
writing to the SRCR1 register, it can be read back correctly when reading the SRCR0
register. If software uses this register to reset the analog comparator module, the write
causes proper operation, but the value of R0 is not reflected by the COMPn bits in the
SRCR1 register. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Analog Comparator Software Reset (SRACMP)
Base 0x400F.E000
Offset 0x53C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
Analog Comparator Module 0 Software Reset
Value Description
0
Analog comparator module is not reset.
1
Analog comparator module is reset.
June 12, 2014
321
Texas Instruments-Production Data
System Control
Register 53: Pulse Width Modulator Software Reset (SRPWM), offset 0x540
The SRPWM register provides software the capability to reset the available PWM modules. This
register provides the same capability as the legacy Software Reset Control n SRCRn registers
specifically for the PWM modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRPWM register. While the SRPWM bit is 1, the peripheral
is held in reset.
2. Software completes the reset process by clearing the SRPWM bit.
There may be latency from the clearing of the SRPWM bit to when the peripheral is ready for use.
Software can check the corresponding PRPWM bit to be sure.
Important: This register should be used to reset the PWM modules. To support legacy software,
the SRCR0 register is available. Setting the PWM bit in the SRCR0 register also resets
the PWM0 module. If the PWM bit is changed by writing to the SRCR0 register, it can
be read back correctly when reading the SRCR0 register. Software must use this register
to reset PWM1, which is not present in the legacy registers. If software uses this register
to reset PWM0, the write causes proper operation, but the value of that bit is not reflected
in the SRCR0 register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Pulse Width Modulator Software Reset (SRPWM)
Base 0x400F.E000
Offset 0x540
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
PWM Module 1 Software Reset
Value Description
0
PWM module 1 is not reset.
1
PWM module 1 is reset.
322
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
R0
RW
0
Description
PWM Module 0 Software Reset
Value Description
0
PWM module 0 is not reset.
1
PWM module 0 is reset.
June 12, 2014
323
Texas Instruments-Production Data
System Control
Register 54: Quadrature Encoder Interface Software Reset (SRQEI), offset
0x544
The SRQEI register provides software the capability to reset the available QEI modules. This register
provides the same capability as the legacy Software Reset Control n SRCRn registers specifically
for the QEI modules and has the same bit polarity as the corresponding SRCRn bits.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRQEI register. While the SRQEI bit is 1, the peripheral is
held in reset.
2. Software completes the reset process by clearing the SRQEI bit.
There may be latency from the clearing of the SRQEI bit to when the peripheral is ready for use.
Software can check the corresponding PRQEI bit to be sure.
Important: This register should be used to reset the QEI modules. To support legacy software, the
SRCR1 register is available. Setting a bit in the SRCR1 register also resets the
corresponding module. Any bits that are changed by writing to the SRCR1 register can
be read back correctly when reading the SRCR1 register. If software uses this register
to reset a legacy peripheral (such as QEI0), the write causes proper operation, but the
value of that bit is not reflected in the SRCR1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Quadrature Encoder Interface Software Reset (SRQEI)
Base 0x400F.E000
Offset 0x544
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
QEI Module 1 Software Reset
Value Description
0
QEI module 1 is not reset.
1
QEI module 1 is reset.
324
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
R0
RW
0
Description
QEI Module 0 Software Reset
Value Description
0
QEI module 0 is not reset.
1
QEI module 0 is reset.
June 12, 2014
325
Texas Instruments-Production Data
System Control
Register 55: EEPROM Software Reset (SREEPROM), offset 0x558
The SREEPROM register provides software the capability to reset the available EEPROM module.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SREEPROM register. While the SREEPROM bit is 1, the
peripheral is held in reset.
2. Software completes the reset process by clearing the SREEPROM bit.
There may be latency from the clearing of the SREEPROM bit to when the peripheral is ready for
use. Software can check the corresponding PREEPROM bit to be sure.
EEPROM Software Reset (SREEPROM)
Base 0x400F.E000
Offset 0x558
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
EEPROM Module Software Reset
Value Description
0
EEPROM module is not reset.
1
EEPROM module is reset.
326
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 56: 32/64-Bit Wide General-Purpose Timer Software Reset
(SRWTIMER), offset 0x55C
The SRWTIMER register provides software the capability to reset the available 32/64-bit wide timer
modules.
A peripheral is reset by software using a simple two-step process:
1. Software sets a bit (or bits) in the SRWTIMER register. While the SRWTIMER bit is 1, the
peripheral is held in reset.
2. Software completes the reset process by clearing the SRWTIMER bit.
There may be latency from the clearing of the SRWTIMER bit to when the peripheral is ready for
use. Software can check the corresponding PRWTIMER bit to be sure.
32/64-Bit Wide General-Purpose Timer Software Reset (SRWTIMER)
Base 0x400F.E000
Offset 0x55C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RW
0
32/64-Bit Wide General-Purpose Timer 5 Software Reset
Value Description
4
R4
RW
0
0
32/64-bit wide general-purpose timer module 5 is not reset.
1
32/64-bit wide general-purpose timer module 5 is reset.
32/64-Bit Wide General-Purpose Timer 4 Software Reset
Value Description
3
R3
RW
0
0
32/64-bit wide general-purpose timer module 4 is not reset.
1
32/64-bit wide general-purpose timer module 4 is reset.
32/64-Bit Wide General-Purpose Timer 3 Software Reset
Value Description
0
32/64-bit wide general-purpose timer module 3 is not reset.
1
32/64-bit wide general-purpose timer module 3 is reset.
June 12, 2014
327
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RW
0
Description
32/64-Bit Wide General-Purpose Timer 2 Software Reset
Value Description
1
R1
RW
0
0
32/64-bit wide general-purpose timer module 2 is not reset.
1
32/64-bit wide general-purpose timer module 2 is reset.
32/64-Bit Wide General-Purpose Timer 1 Software Reset
Value Description
0
R0
RW
0
0
32/64-bit wide general-purpose timer module 1 is not reset.
1
32/64-bit wide general-purpose timer module 1 is reset.
32/64-Bit Wide General-Purpose Timer 0 Software Reset
Value Description
0
32/64-bit wide general-purpose timer module 0 is not reset.
1
32/64-bit wide general-purpose timer module 0 is reset.
328
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 57: Watchdog Timer Run Mode Clock Gating Control (RCGCWD),
offset 0x600
The RCGCWD register provides software the capability to enable and disable watchdog modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the watchdog modules. To
support legacy software, the RCGC0 register is available. A write to the RCGC0 register
also writes the corresponding bit in this register. Any bits that are changed by writing
to the RCGC0 register can be read back correctly with a read of the RCGC0 register.
If software uses this register to write a legacy peripheral (such as Watchdog 0), the
write causes proper operation, but the value of that bit is not reflected in the RCGC0
register. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Watchdog Timer Run Mode Clock Gating Control (RCGCWD)
Base 0x400F.E000
Offset 0x600
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
Watchdog Timer 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
Watchdog module 1 is disabled.
1
Enable and provide a clock to Watchdog module 1 in Run mode.
Watchdog Timer 0 Run Mode Clock Gating Control
Value Description
0
Watchdog module 0 is disabled.
1
Enable and provide a clock to Watchdog module 0 in Run mode.
June 12, 2014
329
Texas Instruments-Production Data
System Control
Register 58: 16/32-Bit General-Purpose Timer Run Mode Clock Gating Control
(RCGCTIMER), offset 0x604
The RCGCTIMER register provides software the capability to enable and disable 16/32-bit timer
modules in Run mode. When enabled, a module is provided a clock and accesses to module registers
are allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the timer modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as Timer 0), the write
causes proper operation, but the value of that bit is not reflected in the RCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
16/32-Bit General-Purpose Timer Run Mode Clock Gating Control (RCGCTIMER)
Base 0x400F.E000
Offset 0x604
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RW
0
16/32-Bit General-Purpose Timer 5 Run Mode Clock Gating Control
Value Description
0
16/32-bit general-purpose timer module 5 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 5 in Run mode.
330
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
4
R4
RW
0
Description
16/32-Bit General-Purpose Timer 4 Run Mode Clock Gating Control
Value Description
3
R3
RW
0
0
16/32-bit general-purpose timer module 4 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 4 in Run mode.
16/32-Bit General-Purpose Timer 3 Run Mode Clock Gating Control
Value Description
2
R2
RW
0
0
16/32-bit general-purpose timer module 3 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 3 in Run mode.
16/32-Bit General-Purpose Timer 2 Run Mode Clock Gating Control
Value Description
1
R1
RW
0
0
16/32-bit general-purpose timer module 2 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 2 in Run mode.
16/32-Bit General-Purpose Timer 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
16/32-bit general-purpose timer module 1 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 1 in Run mode.
16/32-Bit General-Purpose Timer 0 Run Mode Clock Gating Control
Value Description
0
16/32-bit general-purpose timer module 0 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 0 in Run mode.
June 12, 2014
331
Texas Instruments-Production Data
System Control
Register 59: General-Purpose Input/Output Run Mode Clock Gating Control
(RCGCGPIO), offset 0x608
The RCGCGPIO register provides software the capability to enable and disable GPIO modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the GPIO modules. To support
legacy software, the RCGC2 register is available. A write to the RCGC2 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC2 register can be read back correctly with a read of the RCGC2 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as GPIO A), the write
causes proper operation, but the value of that bit is not reflected in the RCGC2 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
General-Purpose Input/Output Run Mode Clock Gating Control (RCGCGPIO)
Base 0x400F.E000
Offset 0x608
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RW
0
GPIO Port F Run Mode Clock Gating Control
Value Description
4
R4
RW
0
0
GPIO Port F is disabled.
1
Enable and provide a clock to GPIO Port F in Run mode.
GPIO Port E Run Mode Clock Gating Control
Value Description
0
GPIO Port E is disabled.
1
Enable and provide a clock to GPIO Port E in Run mode.
332
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
R3
RW
0
Description
GPIO Port D Run Mode Clock Gating Control
Value Description
2
R2
RW
0
0
GPIO Port D is disabled.
1
Enable and provide a clock to GPIO Port D in Run mode.
GPIO Port C Run Mode Clock Gating Control
Value Description
1
R1
RW
0
0
GPIO Port C is disabled.
1
Enable and provide a clock to GPIO Port C in Run mode.
GPIO Port B Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
GPIO Port B is disabled.
1
Enable and provide a clock to GPIO Port B in Run mode.
GPIO Port A Run Mode Clock Gating Control
Value Description
0
GPIO Port A is disabled.
1
Enable and provide a clock to GPIO Port A in Run mode.
June 12, 2014
333
Texas Instruments-Production Data
System Control
Register 60: Micro Direct Memory Access Run Mode Clock Gating Control
(RCGCDMA), offset 0x60C
The RCGCDMA register provides software the capability to enable and disable the μDMA module
in Run mode. When enabled, the module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the μDMA module. To support
legacy software, the RCGC2 register is available. A write to the UDMA bit in the RCGC2
register also writes the R0 bit in this register. If the UDMA bit is changed by writing to the
RCGC2 register, it can be read back correctly with a read of the RCGC2 register. If
software uses this register to control the clock for the μDMA module, the write causes
proper operation, but the UDMA bit in the RCGC2 register does not reflect the value of
the R0 bit. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Micro Direct Memory Access Run Mode Clock Gating Control (RCGCDMA)
Base 0x400F.E000
Offset 0x60C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
μDMA Module Run Mode Clock Gating Control
Value Description
0
μDMA module is disabled.
1
Enable and provide a clock to the μDMA module in Run mode.
334
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 61: Hibernation Run Mode Clock Gating Control (RCGCHIB), offset
0x614
The RCGCHIB register provides software the capability to enable and disable the Hibernation
module in Run mode. When enabled, the module is provided a clock and accesses to module
registers are allowed. When disabled, the clock is disabled to save power and accesses to module
registers generate a bus fault. This register provides the same capability as the legacy Run Mode
Clock Gating Control Register n RCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the Hibernation module. To
support legacy software, the RCGC0 register is available. A write to the HIB bit in the
RCGC0 register also writes the R0 bit in this register. If the HIB bit is changed by writing
to the RCGC0 register, it can be read back correctly with a read of the RCGC0 register.
If software uses this register to control the clock for the Hibernation module, the write
causes proper operation, but the HIB bit in the RCGC0 register does not reflect the
value of the R0 bit. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Hibernation Run Mode Clock Gating Control (RCGCHIB)
Base 0x400F.E000
Offset 0x614
Type RW, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
1
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
1
Hibernation Module Run Mode Clock Gating Control
Value Description
0
Hibernation module is disabled.
1
Enable and provide a clock to the Hibernation module in Run
mode.
June 12, 2014
335
Texas Instruments-Production Data
System Control
Register 62: Universal Asynchronous Receiver/Transmitter Run Mode Clock
Gating Control (RCGCUART), offset 0x618
The RCGCUART register provides software the capability to enable and disable the UART modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the UART modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as UART0), the write
causes proper operation, but the value of that bit is not reflected in the RCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Universal Asynchronous Receiver/Transmitter Run Mode Clock Gating Control (RCGCUART)
Base 0x400F.E000
Offset 0x618
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
R7
R6
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
R7
RW
0
UART Module 7 Run Mode Clock Gating Control
Value Description
6
R6
RW
0
0
UART module 7 is disabled.
1
Enable and provide a clock to UART module 7 in Run mode.
UART Module 6 Run Mode Clock Gating Control
Value Description
0
UART module 6 is disabled.
1
Enable and provide a clock to UART module 6 in Run mode.
336
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
5
R5
RW
0
Description
UART Module 5 Run Mode Clock Gating Control
Value Description
4
R4
RW
0
0
UART module 5 is disabled.
1
Enable and provide a clock to UART module 5 in Run mode.
UART Module 4 Run Mode Clock Gating Control
Value Description
3
R3
RW
0
0
UART module 4 is disabled.
1
Enable and provide a clock to UART module 4 in Run mode.
UART Module 3 Run Mode Clock Gating Control
Value Description
2
R2
RW
0
0
UART module 3 is disabled.
1
Enable and provide a clock to UART module 3 in Run mode.
UART Module 2 Run Mode Clock Gating Control
Value Description
1
R1
RW
0
0
UART module 2 is disabled.
1
Enable and provide a clock to UART module 2 in Run mode.
UART Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
UART module 1 is disabled.
1
Enable and provide a clock to UART module 1 in Run mode.
UART Module 0 Run Mode Clock Gating Control
Value Description
0
UART module 0 is disabled.
1
Enable and provide a clock to UART module 0 in Run mode.
June 12, 2014
337
Texas Instruments-Production Data
System Control
Register 63: Synchronous Serial Interface Run Mode Clock Gating Control
(RCGCSSI), offset 0x61C
The RCGCSSI register provides software the capability to enable and disable the SSI modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the SSI modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as SSI0), the write causes
proper operation, but the value of that bit is not reflected in the RCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Synchronous Serial Interface Run Mode Clock Gating Control (RCGCSSI)
Base 0x400F.E000
Offset 0x61C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RW
0
SSI Module 3 Run Mode Clock Gating Control
Value Description
2
R2
RW
0
0
SSI module 3 is disabled.
1
Enable and provide a clock to SSI module 3 in Run mode.
SSI Module 2 Run Mode Clock Gating Control
Value Description
0
SSI module 2 is disabled.
1
Enable and provide a clock to SSI module 2 in Run mode.
338
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
1
R1
RW
0
Description
SSI Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
SSI module 1 is disabled.
1
Enable and provide a clock to SSI module 1 in Run mode.
SSI Module 0 Run Mode Clock Gating Control
Value Description
0
SSI module 0 is disabled.
1
Enable and provide a clock to SSI module 0 in Run mode.
June 12, 2014
339
Texas Instruments-Production Data
System Control
Register 64: Inter-Integrated Circuit Run Mode Clock Gating Control
(RCGCI2C), offset 0x620
The RCGCI2C register provides software the capability to enable and disable the I2C modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the I2C modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as I2C0), the write causes
proper operation, but the value of that bit is not reflected in the RCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Inter-Integrated Circuit Run Mode Clock Gating Control (RCGCI2C)
Base 0x400F.E000
Offset 0x620
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RW
0
I2C Module 3 Run Mode Clock Gating Control
Value Description
2
R2
RW
0
0
I2C module 3 is disabled.
1
Enable and provide a clock to I2C module 3 in Run mode.
I2C Module 2 Run Mode Clock Gating Control
Value Description
0
I2C module 2 is disabled.
1
Enable and provide a clock to I2C module 2 in Run mode.
340
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
1
R1
RW
0
Description
I2C Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
I2C module 1 is disabled.
1
Enable and provide a clock to I2C module 1 in Run mode.
I2C Module 0 Run Mode Clock Gating Control
Value Description
0
I2C module 0 is disabled.
1
Enable and provide a clock to I2C module 0 in Run mode.
June 12, 2014
341
Texas Instruments-Production Data
System Control
Register 65: Controller Area Network Run Mode Clock Gating Control
(RCGCCAN), offset 0x634
The RCGCCAN register provides software the capability to enable and disable the CAN modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the CAN modules. To support
legacy software, the RCGC0 register is available. A write to the RCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC0 register can be read back correctly with a read of the RCGC0 register. If software
uses this register to write a legacy peripheral (such as CAN0), the write causes proper
operation, but the value of that bit is not reflected in the RCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Controller Area Network Run Mode Clock Gating Control (RCGCCAN)
Base 0x400F.E000
Offset 0x634
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
CAN Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
CAN module 1 is disabled.
1
Enable and provide a clock to CAN module 1 in Run mode.
CAN Module 0 Run Mode Clock Gating Control
Value Description
0
CAN module 0 is disabled.
1
Enable and provide a clock to CAN module 0 in Run mode.
342
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 66: Analog-to-Digital Converter Run Mode Clock Gating Control
(RCGCADC), offset 0x638
The RCGCADC register provides software the capability to enable and disable the ADC modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the ADC modules. To support
legacy software, the RCGC0 register is available. A write to the RCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC0 register can be read back correctly with a read of the RCGC0 register. If software
uses this register to write a legacy peripheral (such as ADC0), the write causes proper
operation, but the value of that bit is not reflected in the RCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Analog-to-Digital Converter Run Mode Clock Gating Control (RCGCADC)
Base 0x400F.E000
Offset 0x638
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
ADC Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
ADC module 1 is disabled.
1
Enable and provide a clock to ADC module 1 in Run mode.
ADC Module 0 Run Mode Clock Gating Control
Value Description
0
ADC module 0 is disabled.
1
Enable and provide a clock to ADC module 0 in Run mode.
June 12, 2014
343
Texas Instruments-Production Data
System Control
Register 67: Analog Comparator Run Mode Clock Gating Control
(RCGCACMP), offset 0x63C
The RCGCACMP register provides software the capability to enable and disable the analog
comparator module in Run mode. When enabled, the module is provided a clock and accesses to
module registers are allowed. When disabled, the clock is disabled to save power and accesses to
module registers generate a bus fault. This register provides the same capability as the legacy Run
Mode Clock Gating Control Register n RCGCn registers specifically for the watchdog modules
and has the same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the analog comparator module.
To support legacy software, the RCGC1 register is available. Setting any of the COMPn
bits in the RCGC1 register also sets the R0 bit in this register. If any of the COMPn bits
are set by writing to the RCGC1 register, it can be read back correctly when reading
the RCGC1 register. If software uses this register to change the clocking for the analog
comparator module, the write causes proper operation, but the value R0 is not reflected
by the COMPn bits in the RCGC1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog Comparator Run Mode Clock Gating Control (RCGCACMP)
Base 0x400F.E000
Offset 0x63C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
Analog Comparator Module 0 Run Mode Clock Gating Control
Value Description
0
Analog comparator module is disabled.
1
Enable and provide a clock to the analog comparator module
in Run mode.
344
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 68: Pulse Width Modulator Run Mode Clock Gating Control
(RCGCPWM), offset 0x640
The RCGCPWM register provides software the capability to enable and disable the PWM modules
in Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the PWM modules. To support
legacy software, the RCGC0 register is available. A write to the PWM bit in the RCGC0
register also writes the R0 bit in this register. If the PWM bit is changed by writing to the
RCGC0 register, it can be read back correctly with a read of the RCGC0 register.
Software must use this register to support modules that are not present in the legacy
registers. If software uses this register to write to R0, the write causes proper operation,
but the value of that bit is not reflected in the PWM bit in the RCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Pulse Width Modulator Run Mode Clock Gating Control (RCGCPWM)
Base 0x400F.E000
Offset 0x640
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
PWM Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
PWM module 1 is disabled.
1
Enable and provide a clock to PWM module 1 in Run mode.
PWM Module 0 Run Mode Clock Gating Control
Value Description
0
PWM module 0 is disabled.
1
Enable and provide a clock to PWM module 0 in Run mode.
June 12, 2014
345
Texas Instruments-Production Data
System Control
Register 69: Quadrature Encoder Interface Run Mode Clock Gating Control
(RCGCQEI), offset 0x644
The RCGCQEI register provides software the capability to enable and disable the QEI modules in
Run mode. When enabled, a module is provided a clock and accesses to module registers are
allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding RCGCn bits.
Important: This register should be used to control the clocking for the QEI modules. To support
legacy software, the RCGC1 register is available. A write to the RCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
RCGC1 register can be read back correctly with a read of the RCGC1 register. If software
uses this register to write a legacy peripheral (such as QEI0), the write causes proper
operation, but the value of that bit is not reflected in the RCGC1 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Quadrature Encoder Interface Run Mode Clock Gating Control (RCGCQEI)
Base 0x400F.E000
Offset 0x644
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RW
0
QEI Module 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
QEI module 1 is disabled.
1
Enable and provide a clock to QEI module 1 in Run mode.
QEI Module 0 Run Mode Clock Gating Control
Value Description
0
QEI module 0 is disabled.
1
Enable and provide a clock to QEI module 0 in Run mode.
346
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 70: EEPROM Run Mode Clock Gating Control (RCGCEEPROM), offset
0x658
The RCGCEEPROM register provides software the capability to enable and disable the EEPROM
module in Run mode. When enabled, the module is provided a clock and accesses to module
registers are allowed. When disabled, the clock is disabled to save power and accesses to module
registers generate a bus fault.
EEPROM Run Mode Clock Gating Control (RCGCEEPROM)
Base 0x400F.E000
Offset 0x658
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RW
0
EEPROM Module Run Mode Clock Gating Control
Value Description
0
EEPROM module is disabled.
1
Enable and provide a clock to the EEPROM module in Run
mode.
June 12, 2014
347
Texas Instruments-Production Data
System Control
Register 71: 32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating
Control (RCGCWTIMER), offset 0x65C
The RCGCWTIMER register provides software the capability to enable and disable 3264-bit timer
modules in Run mode. When enabled, a module is provided a clock and accesses to module registers
are allowed. When disabled, the clock is disabled to save power and accesses to module registers
generate a bus fault. This register provides the same capability as the legacy Run Mode Clock
Gating Control Register n RCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding RCGCn bits.
32/64-Bit Wide General-Purpose Timer Run Mode Clock Gating Control (RCGCWTIMER)
Base 0x400F.E000
Offset 0x65C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RW
0
32/64-Bit Wide General-Purpose Timer 5 Run Mode Clock Gating Control
Value Description
4
R4
RW
0
0
32/64-bit wide general-purpose timer module 5 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 5 in Run mode.
32/64-Bit Wide General-Purpose Timer 4 Run Mode Clock Gating Control
Value Description
3
R3
RW
0
0
32/64-bit wide general-purpose timer module 4 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 4 in Run mode.
32/64-Bit Wide General-Purpose Timer 3 Run Mode Clock Gating Control
Value Description
0
32/64-bit wide general-purpose timer module 3 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 3 in Run mode.
348
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
R2
RW
0
Description
32/64-Bit Wide General-Purpose Timer 2 Run Mode Clock Gating Control
Value Description
1
R1
RW
0
0
32/64-bit wide general-purpose timer module 2 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 2 in Run mode.
32/64-Bit Wide General-Purpose Timer 1 Run Mode Clock Gating Control
Value Description
0
R0
RW
0
0
32/64-bit wide general-purpose timer module 1 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 1 in Run mode.
32/64-Bit Wide General-Purpose Timer 0 Run Mode Clock Gating Control
Value Description
0
32/64-bit wide general-purpose timer module 0 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 0 in Run mode.
June 12, 2014
349
Texas Instruments-Production Data
System Control
Register 72: Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD),
offset 0x700
The SCGCWD register provides software the capability to enable and disable watchdog modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the watchdog modules. To
support legacy software, the SCGC0 register is available. A write to the SCGC0 register
also writes the corresponding bit in this register. Any bits that are changed by writing
to the SCGC0 register can be read back correctly with a read of the SCGC0 register.
If software uses this register to write a legacy peripheral (such as Watchdog 0), the
write causes proper operation, but the value of that bit is not reflected in the SCGC0
register. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Watchdog Timer Sleep Mode Clock Gating Control (SCGCWD)
Base 0x400F.E000
Offset 0x700
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
RW
0
Watchdog Timer 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
Watchdog module 1 is disabled.
1
Enable and provide a clock to Watchdog module 1 in sleep
mode.
Watchdog Timer 0 Sleep Mode Clock Gating Control
Value Description
0
Watchdog module 0 is disabled.
1
Enable and provide a clock to Watchdog module 0 in sleep
mode.
350
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 73: 16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control
(SCGCTIMER), offset 0x704
The SCGCTIMER register provides software the capability to enable and disable 16/32-bit timer
modules in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Sleep Mode Clock
Gating Control Register n SCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the timer modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as Timer 0), the write
causes proper operation, but the value of that bit is not reflected in the SCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
16/32-Bit General-Purpose Timer Sleep Mode Clock Gating Control (SCGCTIMER)
Base 0x400F.E000
Offset 0x704
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
S5
S4
S3
S2
S1
S0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
S5
RW
0
16/32-Bit General-Purpose Timer 5 Sleep Mode Clock Gating Control
Value Description
4
S4
RW
0
0
16/32-bit general-purpose timer module 5 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 5 in sleep mode.
16/32-Bit General-Purpose Timer 4 Sleep Mode Clock Gating Control
Value Description
0
16/32-bit general-purpose timer module 4 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 4 in sleep mode.
June 12, 2014
351
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
S3
RW
0
Description
16/32-Bit General-Purpose Timer 3 Sleep Mode Clock Gating Control
Value Description
2
S2
RW
0
0
16/32-bit general-purpose timer module 3 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 3 in sleep mode.
16/32-Bit General-Purpose Timer 2 Sleep Mode Clock Gating Control
Value Description
1
S1
RW
0
0
16/32-bit general-purpose timer module 2 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 2 in sleep mode.
16/32-Bit General-Purpose Timer 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
16/32-bit general-purpose timer module 1 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 1 in sleep mode.
16/32-Bit General-Purpose Timer 0 Sleep Mode Clock Gating Control
Value Description
0
16/32-bit general-purpose timer module 0 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 0 in sleep mode.
352
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 74: General-Purpose Input/Output Sleep Mode Clock Gating Control
(SCGCGPIO), offset 0x708
The SCGCGPIO register provides software the capability to enable and disable GPIO modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the GPIO modules. To support
legacy software, the SCGC2 register is available. A write to the SCGC2 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC2 register can be read back correctly with a read of the SCGC2 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as GPIO A), the write
causes proper operation, but the value of that bit is not reflected in the SCGC2 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
General-Purpose Input/Output Sleep Mode Clock Gating Control (SCGCGPIO)
Base 0x400F.E000
Offset 0x708
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
S5
S4
S3
S2
S1
S0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
S5
RW
0
GPIO Port F Sleep Mode Clock Gating Control
Value Description
4
S4
RW
0
0
GPIO Port F is disabled.
1
Enable and provide a clock to GPIO Port F in sleep mode.
GPIO Port E Sleep Mode Clock Gating Control
Value Description
0
GPIO Port E is disabled.
1
Enable and provide a clock to GPIO Port E in sleep mode.
June 12, 2014
353
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
S3
RW
0
Description
GPIO Port D Sleep Mode Clock Gating Control
Value Description
2
S2
RW
0
0
GPIO Port D is disabled.
1
Enable and provide a clock to GPIO Port D in sleep mode.
GPIO Port C Sleep Mode Clock Gating Control
Value Description
1
S1
RW
0
0
GPIO Port C is disabled.
1
Enable and provide a clock to GPIO Port C in sleep mode.
GPIO Port B Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
GPIO Port B is disabled.
1
Enable and provide a clock to GPIO Port B in sleep mode.
GPIO Port A Sleep Mode Clock Gating Control
Value Description
0
GPIO Port A is disabled.
1
Enable and provide a clock to GPIO Port A in sleep mode.
354
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 75: Micro Direct Memory Access Sleep Mode Clock Gating Control
(SCGCDMA), offset 0x70C
The SCGCDMA register provides software the capability to enable and disable the μDMA module
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the μDMA module. To support
legacy software, the SCGC2 register is available. A write to the UDMA bit in the SCGC2
register also writes the S0 bit in this register. If the UDMA bit is changed by writing to the
SCGC2 register, it can be read back correctly with a read of the SCGC2 register. If
software uses this register to control the clock for the μDMA module, the write causes
proper operation, but the UDMA bit in the SCGC2 register does not reflect the value of
the S0 bit. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Micro Direct Memory Access Sleep Mode Clock Gating Control (SCGCDMA)
Base 0x400F.E000
Offset 0x70C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
S0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
RW
0
μDMA Module Sleep Mode Clock Gating Control
Value Description
0
μDMA module is disabled.
1
Enable and provide a clock to the μDMA module in sleep mode.
June 12, 2014
355
Texas Instruments-Production Data
System Control
Register 76: Hibernation Sleep Mode Clock Gating Control (SCGCHIB), offset
0x714
The SCGCHIB register provides software the capability to enable and disable the Hibernation module
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the Hibernation module. To
support legacy software, the SCGC0 register is available. A write to the HIB bit in the
SCGC0 register also writes the S0 bit in this register. If the HIB bit is changed by writing
to the SCGC0 register, it can be read back correctly with a read of the SCGC0 register.
If software uses this register to control the clock for the Hibernation module, the write
causes proper operation, but the HIB bit in the SCGC0 register does not reflect the
value of the S0 bit. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Hibernation Sleep Mode Clock Gating Control (SCGCHIB)
Base 0x400F.E000
Offset 0x714
Type RW, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
1
reserved
Type
Reset
reserved
Type
Reset
RO
0
S0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
RW
1
Hibernation Module Sleep Mode Clock Gating Control
Value Description
0
Hibernation module is disabled.
1
Enable and provide a clock to the Hibernation module in sleep
mode.
356
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 77: Universal Asynchronous Receiver/Transmitter Sleep Mode Clock
Gating Control (SCGCUART), offset 0x718
The SCGCUART register provides software the capability to enable and disable the UART modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the UART modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as UART0), the write
causes proper operation, but the value of that bit is not reflected in the SCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Universal Asynchronous Receiver/Transmitter Sleep Mode Clock Gating Control (SCGCUART)
Base 0x400F.E000
Offset 0x718
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
S7
S6
S5
S4
S3
S2
S1
S0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
S7
RW
0
UART Module 7 Sleep Mode Clock Gating Control
Value Description
6
S6
RW
0
0
UART module 7 is disabled.
1
Enable and provide a clock to UART module 7 in sleep mode.
UART Module 6 Sleep Mode Clock Gating Control
Value Description
0
UART module 6 is disabled.
1
Enable and provide a clock to UART module 6 in sleep mode.
June 12, 2014
357
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
5
S5
RW
0
Description
UART Module 5 Sleep Mode Clock Gating Control
Value Description
4
S4
RW
0
0
UART module 5 is disabled.
1
Enable and provide a clock to UART module 5 in sleep mode.
UART Module 4 Sleep Mode Clock Gating Control
Value Description
3
S3
RW
0
0
UART module 4 is disabled.
1
Enable and provide a clock to UART module 4 in sleep mode.
UART Module 3 Sleep Mode Clock Gating Control
Value Description
2
S2
RW
0
0
UART module 3 is disabled.
1
Enable and provide a clock to UART module 3 in sleep mode.
UART Module 2 Sleep Mode Clock Gating Control
Value Description
1
S1
RW
0
0
UART module 2 is disabled.
1
Enable and provide a clock to UART module 2 in sleep mode.
UART Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
UART module 1 is disabled.
1
Enable and provide a clock to UART module 1 in sleep mode.
UART Module 0 Sleep Mode Clock Gating Control
Value Description
0
UART module 0 is disabled.
1
Enable and provide a clock to UART module 0 in sleep mode.
358
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 78: Synchronous Serial Interface Sleep Mode Clock Gating Control
(SCGCSSI), offset 0x71C
The SCGCSSI register provides software the capability to enable and disable the SSI modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the SSI modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as SSI0), the write causes
proper operation, but the value of that bit is not reflected in the SCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Synchronous Serial Interface Sleep Mode Clock Gating Control (SCGCSSI)
Base 0x400F.E000
Offset 0x71C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
S3
S2
S1
S0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
S3
RW
0
SSI Module 3 Sleep Mode Clock Gating Control
Value Description
2
S2
RW
0
0
SSI module 3 is disabled.
1
Enable and provide a clock to SSI module 3 in sleep mode.
SSI Module 2 Sleep Mode Clock Gating Control
Value Description
0
SSI module 2 is disabled.
1
Enable and provide a clock to SSI module 2 in sleep mode.
June 12, 2014
359
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1
S1
RW
0
Description
SSI Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
SSI module 1 is disabled.
1
Enable and provide a clock to SSI module 1 in sleep mode.
SSI Module 0 Sleep Mode Clock Gating Control
Value Description
0
SSI module 0 is disabled.
1
Enable and provide a clock to SSI module 0 in sleep mode.
360
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 79: Inter-Integrated Circuit Sleep Mode Clock Gating Control
(SCGCI2C), offset 0x720
The SCGCI2C register provides software the capability to enable and disable the I2C modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the I2C modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as I2C0), the write causes
proper operation, but the value of that bit is not reflected in the SCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Inter-Integrated Circuit Sleep Mode Clock Gating Control (SCGCI2C)
Base 0x400F.E000
Offset 0x720
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
S3
S2
S1
S0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
S3
RW
0
I2C Module 3 Sleep Mode Clock Gating Control
Value Description
2
S2
RW
0
0
I2C module 3 is disabled.
1
Enable and provide a clock to I2C module 3 in sleep mode.
I2C Module 2 Sleep Mode Clock Gating Control
Value Description
0
I2C module 2 is disabled.
1
Enable and provide a clock to I2C module 2 in sleep mode.
June 12, 2014
361
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
1
S1
RW
0
Description
I2C Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
I2C module 1 is disabled.
1
Enable and provide a clock to I2C module 1 in sleep mode.
I2C Module 0 Sleep Mode Clock Gating Control
Value Description
0
I2C module 0 is disabled.
1
Enable and provide a clock to I2C module 0 in sleep mode.
362
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 80: Controller Area Network Sleep Mode Clock Gating Control
(SCGCCAN), offset 0x734
The SCGCCAN register provides software the capability to enable and disable the CAN modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the CAN modules. To support
legacy software, the SCGC0 register is available. A write to the SCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC0 register can be read back correctly with a read of the SCGC0 register. If software
uses this register to write a legacy peripheral (such as CAN0), the write causes proper
operation, but the value of that bit is not reflected in the SCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Controller Area Network Sleep Mode Clock Gating Control (SCGCCAN)
Base 0x400F.E000
Offset 0x734
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
RW
0
CAN Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
CAN module 1 is disabled.
1
Enable and provide a clock to CAN module 1 in sleep mode.
CAN Module 0 Sleep Mode Clock Gating Control
Value Description
0
CAN module 0 is disabled.
1
Enable and provide a clock to CAN module 0 in sleep mode.
June 12, 2014
363
Texas Instruments-Production Data
System Control
Register 81: Analog-to-Digital Converter Sleep Mode Clock Gating Control
(SCGCADC), offset 0x738
The SCGCADC register provides software the capability to enable and disable the ADC modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the ADC modules. To support
legacy software, the SCGC0 register is available. A write to the SCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC0 register can be read back correctly with a read of the SCGC0 register. If software
uses this register to write a legacy peripheral (such as ADC0), the write causes proper
operation, but the value of that bit is not reflected in the SCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Analog-to-Digital Converter Sleep Mode Clock Gating Control (SCGCADC)
Base 0x400F.E000
Offset 0x738
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
RW
0
ADC Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
ADC module 1 is disabled.
1
Enable and provide a clock to ADC module 1 in sleep mode.
ADC Module 0 Sleep Mode Clock Gating Control
Value Description
0
ADC module 0 is disabled.
1
Enable and provide a clock to ADC module 0 in sleep mode.
364
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 82: Analog Comparator Sleep Mode Clock Gating Control
(SCGCACMP), offset 0x73C
The SCGCACMP register provides software the capability to enable and disable the analog
comparator module in sleep mode. When enabled, a module is provided a clock. When disabled,
the clock is disabled to save power. This register provides the same capability as the legacy Sleep
Mode Clock Gating Control Register n SCGCn registers specifically for the watchdog modules
and has the same bit polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the analog comparator module.
To support legacy software, the SCGC1 register is available. Setting any of the COMPn
bits in the SCGC1 register also sets the S0 bit in this register. If any of the COMPn bits
are set by writing to the SCGC1 register, it can be read back correctly when reading
the SCGC1 register. If software uses this register to change the clocking for the analog
comparator module, the write causes proper operation, but the value S0 is not reflected
by the COMPn bits in the SCGC1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog Comparator Sleep Mode Clock Gating Control (SCGCACMP)
Base 0x400F.E000
Offset 0x73C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
S0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
RW
0
Analog Comparator Module 0 Sleep Mode Clock Gating Control
Value Description
0
Analog comparator module is disabled.
1
Enable and provide a clock to the analog comparator module
in sleep mode.
June 12, 2014
365
Texas Instruments-Production Data
System Control
Register 83: Pulse Width Modulator Sleep Mode Clock Gating Control
(SCGCPWM), offset 0x740
The SCGCPWM register provides software the capability to enable and disable the PWM modules
in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the PWM modules. To support
legacy software, the SCGC0 register is available. A write to the PWM bit in the SCGC0
register also writes the S0 bit in this register. If the PWM bit is changed by writing to the
SCGC0 register, it can be read back correctly with a read of the SCGC0 register.
Software must use this register to support modules that are not present in the legacy
registers. If software uses this register to write to S0, the write causes proper operation,
but the value of that bit is not reflected in the PWM bit in the SCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Pulse Width Modulator Sleep Mode Clock Gating Control (SCGCPWM)
Base 0x400F.E000
Offset 0x740
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
S1
S0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
RW
0
PWM Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
PWM module 1 is disabled.
1
Enable and provide a clock to PWM module 1 in sleep mode.
PWM Module 0 Sleep Mode Clock Gating Control
Value Description
0
PWM module 0 is disabled.
1
Enable and provide a clock to PWM module 0 in sleep mode.
366
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 84: Quadrature Encoder Interface Sleep Mode Clock Gating Control
(SCGCQEI), offset 0x744
The SCGCQEI register provides software the capability to enable and disable the QEI modules in
sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled to
save power. This register provides the same capability as the legacy Sleep Mode Clock Gating
Control Register n SCGCn registers specifically for the watchdog modules and has the same bit
polarity as the corresponding SCGCn bits.
Important: This register should be used to control the clocking for the QEI modules. To support
legacy software, the SCGC1 register is available. A write to the SCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
SCGC1 register can be read back correctly with a read of the SCGC1 register. If software
uses this register to write a legacy peripheral (such as QEI0), the write causes proper
operation, but the value of that bit is not reflected in the SCGC1 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Quadrature Encoder Interface Sleep Mode Clock Gating Control (SCGCQEI)
Base 0x400F.E000
Offset 0x744
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
S1
S0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
S1
RW
0
QEI Module 1 Sleep Mode Clock Gating Control
Value Description
0
S0
RW
0
0
QEI module 1 is disabled.
1
Enable and provide a clock to QEI module 1 in sleep mode.
QEI Module 0 Sleep Mode Clock Gating Control
Value Description
0
QEI module 0 is disabled.
1
Enable and provide a clock to QEI module 0 in sleep mode.
June 12, 2014
367
Texas Instruments-Production Data
System Control
Register 85: EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM),
offset 0x758
The SCGCEEPROM register provides software the capability to enable and disable the EEPROM
module in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power.
EEPROM Sleep Mode Clock Gating Control (SCGCEEPROM)
Base 0x400F.E000
Offset 0x758
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
S0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
S0
RW
0
EEPROM Module Sleep Mode Clock Gating Control
Value Description
0
EEPROM module is disabled.
1
Enable and provide a clock to the EEPROM module in sleep
mode.
368
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 86: 32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating
Control (SCGCWTIMER), offset 0x75C
The SCGCWTIMER register provides software the capability to enable and disable 3264-bit timer
modules in sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Sleep Mode Clock
Gating Control Register n SCGCn registers specifically for the timer modules and has the same
bit polarity as the corresponding SCGCn bits.
32/64-Bit Wide General-Purpose Timer Sleep Mode Clock Gating Control (SCGCWTIMER)
Base 0x400F.E000
Offset 0x75C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
S5
S4
S3
S2
S1
S0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
S5
RW
0
32/64-Bit Wide General-Purpose Timer 5 Sleep Mode Clock Gating
Control
Value Description
4
S4
RW
0
0
32/64-bit wide general-purpose timer module 5 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 5 in sleep mode.
32/64-Bit Wide General-Purpose Timer 4 Sleep Mode Clock Gating
Control
Value Description
3
S3
RW
0
0
32/64-bit wide general-purpose timer module 4 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 4 in sleep mode.
32/64-Bit Wide General-Purpose Timer 3 Sleep Mode Clock Gating
Control
Value Description
0
32/64-bit wide general-purpose timer module 3 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 3 in sleep mode.
June 12, 2014
369
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
S2
RW
0
Description
32/64-Bit Wide General-Purpose Timer 2 Sleep Mode Clock Gating
Control
Value Description
1
S1
RW
0
0
32/64-bit wide general-purpose timer module 2 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 2 in sleep mode.
32/64-Bit Wide General-Purpose Timer 1 Sleep Mode Clock Gating
Control
Value Description
0
S0
RW
0
0
32/64-bit wide general-purpose timer module 1 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 1 in sleep mode.
32/64-Bit Wide General-Purpose Timer 0 Sleep Mode Clock Gating
Control
Value Description
0
32/64-bit wide general-purpose timer module 0 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 0 in sleep mode.
370
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 87: Watchdog Timer Deep-Sleep Mode Clock Gating Control
(DCGCWD), offset 0x800
The DCGCWD register provides software the capability to enable and disable watchdog modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the watchdog modules. To
support legacy software, the DCGC0 register is available. A write to the DCGC0 register
also writes the corresponding bit in this register. Any bits that are changed by writing
to the DCGC0 register can be read back correctly with a read of the DCGC0 register.
If software uses this register to write a legacy peripheral (such as Watchdog 0), the
write causes proper operation, but the value of that bit is not reflected in the DCGC0
register. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Watchdog Timer Deep-Sleep Mode Clock Gating Control (DCGCWD)
Base 0x400F.E000
Offset 0x800
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
RW
0
Watchdog Timer 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
Watchdog module 1 is disabled.
1
Enable and provide a clock to Watchdog module 1 in deep-sleep
mode.
Watchdog Timer 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
Watchdog module 0 is disabled.
1
Enable and provide a clock to Watchdog module 0 in deep-sleep
mode.
June 12, 2014
371
Texas Instruments-Production Data
System Control
Register 88: 16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating
Control (DCGCTIMER), offset 0x804
The DCGCTIMER register provides software the capability to enable and disable 16/32-bit timer
modules in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the
clock is disabled to save power. This register provides the same capability as the legacy Deep-Sleep
Mode Clock Gating Control Register n DCGCn registers specifically for the timer modules and
has the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the timer modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as Timer 0), the write
causes proper operation, but the value of that bit is not reflected in the DCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
16/32-Bit General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCTIMER)
Base 0x400F.E000
Offset 0x804
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
D5
D4
D3
D2
D1
D0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
D5
RW
0
16/32-Bit General-Purpose Timer 5 Deep-Sleep Mode Clock Gating
Control
Value Description
0
16/32-bit general-purpose timer module 5 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 5 in deep-sleep mode.
372
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
4
D4
RW
0
Description
16/32-Bit General-Purpose Timer 4 Deep-Sleep Mode Clock Gating
Control
Value Description
3
D3
RW
0
0
16/32-bit general-purpose timer module 4 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 4 in deep-sleep mode.
16/32-Bit General-Purpose Timer 3 Deep-Sleep Mode Clock Gating
Control
Value Description
2
D2
RW
0
0
16/32-bit general-purpose timer module 3 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 3 in deep-sleep mode.
16/32-Bit General-Purpose Timer 2 Deep-Sleep Mode Clock Gating
Control
Value Description
1
D1
RW
0
0
16/32-bit general-purpose timer module 2 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 2 in deep-sleep mode.
16/32-Bit General-Purpose Timer 1 Deep-Sleep Mode Clock Gating
Control
Value Description
0
D0
RW
0
0
16/32-bit general-purpose timer module 1 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 1 in deep-sleep mode.
16/32-Bit General-Purpose Timer 0 Deep-Sleep Mode Clock Gating
Control
Value Description
0
16/32-bit general-purpose timer module 0 is disabled.
1
Enable and provide a clock to 16/32-bit general-purpose timer
module 0 in deep-sleep mode.
June 12, 2014
373
Texas Instruments-Production Data
System Control
Register 89: General-Purpose Input/Output Deep-Sleep Mode Clock Gating
Control (DCGCGPIO), offset 0x808
The DCGCGPIO register provides software the capability to enable and disable GPIO modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the GPIO modules. To support
legacy software, the DCGC2 register is available. A write to the DCGC2 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC2 register can be read back correctly with a read of the DCGC2 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as GPIO A), the write
causes proper operation, but the value of that bit is not reflected in the DCGC2 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
General-Purpose Input/Output Deep-Sleep Mode Clock Gating Control (DCGCGPIO)
Base 0x400F.E000
Offset 0x808
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
D5
D4
D3
D2
D1
D0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
D5
RW
0
GPIO Port F Deep-Sleep Mode Clock Gating Control
Value Description
4
D4
RW
0
0
GPIO Port F is disabled.
1
Enable and provide a clock to GPIO Port F in deep-sleep mode.
GPIO Port E Deep-Sleep Mode Clock Gating Control
Value Description
0
GPIO Port E is disabled.
1
Enable and provide a clock to GPIO Port E in deep-sleep mode.
374
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
D3
RW
0
Description
GPIO Port D Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
RW
0
0
GPIO Port D is disabled.
1
Enable and provide a clock to GPIO Port D in deep-sleep mode.
GPIO Port C Deep-Sleep Mode Clock Gating Control
Value Description
1
D1
RW
0
0
GPIO Port C is disabled.
1
Enable and provide a clock to GPIO Port C in deep-sleep mode.
GPIO Port B Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
GPIO Port B is disabled.
1
Enable and provide a clock to GPIO Port B in deep-sleep mode.
GPIO Port A Deep-Sleep Mode Clock Gating Control
Value Description
0
GPIO Port A is disabled.
1
Enable and provide a clock to GPIO Port A in deep-sleep mode.
June 12, 2014
375
Texas Instruments-Production Data
System Control
Register 90: Micro Direct Memory Access Deep-Sleep Mode Clock Gating
Control (DCGCDMA), offset 0x80C
The DCGCDMA register provides software the capability to enable and disable the μDMA module
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the μDMA module. To support
legacy software, the DCGC2 register is available. A write to the UDMA bit in the DCGC2
register also writes the D0 bit in this register. If the UDMA bit is changed by writing to the
DCGC2 register, it can be read back correctly with a read of the DCGC2 register. If
software uses this register to control the clock for the μDMA module, the write causes
proper operation, but the UDMA bit in the DCGC2 register does not reflect the value of
the D0 bit. If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Micro Direct Memory Access Deep-Sleep Mode Clock Gating Control (DCGCDMA)
Base 0x400F.E000
Offset 0x80C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
D0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
RW
0
μDMA Module Deep-Sleep Mode Clock Gating Control
Value Description
0
μDMA module is disabled.
1
Enable and provide a clock to the μDMA module in deep-sleep
mode.
376
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 91: Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB),
offset 0x814
The DCGCHIB register provides software the capability to enable and disable the Hibernation
module in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock
is disabled to save power. This register provides the same capability as the legacy Deep-Sleep
Mode Clock Gating Control Register n DCGCn registers specifically for the watchdog modules
and has the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the Hibernation module. To
support legacy software, the DCGC0 register is available. A write to the HIB bit in the
DCGC0 register also writes the D0 bit in this register. If the HIB bit is changed by writing
to the DCGC0 register, it can be read back correctly with a read of the DCGC0 register.
If software uses this register to control the clock for the Hibernation module, the write
causes proper operation, but the HIB bit in the DCGC0 register does not reflect the
value of the D0 bit. If software uses both legacy and peripheral-specific register accesses,
the peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Hibernation Deep-Sleep Mode Clock Gating Control (DCGCHIB)
Base 0x400F.E000
Offset 0x814
Type RW, reset 0x0000.0001
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
1
reserved
Type
Reset
reserved
Type
Reset
RO
0
D0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
RW
1
Hibernation Module Deep-Sleep Mode Clock Gating Control
Value Description
0
Hibernation module is disabled.
1
Enable and provide a clock to the Hibernation module in
deep-sleep mode.
June 12, 2014
377
Texas Instruments-Production Data
System Control
Register 92: Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode
Clock Gating Control (DCGCUART), offset 0x818
The DCGCUART register provides software the capability to enable and disable the UART modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the UART modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as UART0), the write
causes proper operation, but the value of that bit is not reflected in the DCGC1 register.
If software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Universal Asynchronous Receiver/Transmitter Deep-Sleep Mode Clock Gating Control (DCGCUART)
Base 0x400F.E000
Offset 0x818
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
D7
RW
0
UART Module 7 Deep-Sleep Mode Clock Gating Control
Value Description
6
D6
RW
0
0
UART module 7 is disabled.
1
Enable and provide a clock to UART module 7 in deep-sleep
mode.
UART Module 6 Deep-Sleep Mode Clock Gating Control
Value Description
0
UART module 6 is disabled.
1
Enable and provide a clock to UART module 6 in deep-sleep
mode.
378
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
5
D5
RW
0
Description
UART Module 5 Deep-Sleep Mode Clock Gating Control
Value Description
4
D4
RW
0
0
UART module 5 is disabled.
1
Enable and provide a clock to UART module 5 in deep-sleep
mode.
UART Module 4 Deep-Sleep Mode Clock Gating Control
Value Description
3
D3
RW
0
0
UART module 4 is disabled.
1
Enable and provide a clock to UART module 4 in deep-sleep
mode.
UART Module 3 Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
RW
0
0
UART module 3 is disabled.
1
Enable and provide a clock to UART module 3 in deep-sleep
mode.
UART Module 2 Deep-Sleep Mode Clock Gating Control
Value Description
1
D1
RW
0
0
UART module 2 is disabled.
1
Enable and provide a clock to UART module 2 in deep-sleep
mode.
UART Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
UART module 1 is disabled.
1
Enable and provide a clock to UART module 1 in deep-sleep
mode.
UART Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
UART module 0 is disabled.
1
Enable and provide a clock to UART module 0 in deep-sleep
mode.
June 12, 2014
379
Texas Instruments-Production Data
System Control
Register 93: Synchronous Serial Interface Deep-Sleep Mode Clock Gating
Control (DCGCSSI), offset 0x81C
The DCGCSSI register provides software the capability to enable and disable the SSI modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the SSI modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as SSI0), the write causes
proper operation, but the value of that bit is not reflected in the DCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Synchronous Serial Interface Deep-Sleep Mode Clock Gating Control (DCGCSSI)
Base 0x400F.E000
Offset 0x81C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
D3
D2
D1
D0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
D3
RW
0
SSI Module 3 Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
RW
0
0
SSI module 3 is disabled.
1
Enable and provide a clock to SSI module 3 in deep-sleep mode.
SSI Module 2 Deep-Sleep Mode Clock Gating Control
Value Description
0
SSI module 2 is disabled.
1
Enable and provide a clock to SSI module 2 in deep-sleep mode.
380
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
1
D1
RW
0
Description
SSI Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
SSI module 1 is disabled.
1
Enable and provide a clock to SSI module 1 in deep-sleep mode.
SSI Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
SSI module 0 is disabled.
1
Enable and provide a clock to SSI module 0 in deep-sleep mode.
June 12, 2014
381
Texas Instruments-Production Data
System Control
Register 94: Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control
(DCGCI2C), offset 0x820
The DCGCI2C register provides software the capability to enable and disable the I2C modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the I2C modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. Software
must use this register to support modules that are not present in the legacy registers.
If software uses this register to write a legacy peripheral (such as I2C0), the write causes
proper operation, but the value of that bit is not reflected in the DCGC1 register. If
software uses both legacy and peripheral-specific register accesses, the
peripheral-specific registers must be accessed by read-modify-write operations that
affect only peripherals that are not present in the legacy registers. In this manner, both
the peripheral-specific and legacy registers have coherent information.
Inter-Integrated Circuit Deep-Sleep Mode Clock Gating Control (DCGCI2C)
Base 0x400F.E000
Offset 0x820
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
D3
D2
D1
D0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
D3
RW
0
I2C Module 3 Deep-Sleep Mode Clock Gating Control
Value Description
2
D2
RW
0
0
I2C module 3 is disabled.
1
Enable and provide a clock to I2C module 3 in deep-sleep mode.
I2C Module 2 Deep-Sleep Mode Clock Gating Control
Value Description
0
I2C module 2 is disabled.
1
Enable and provide a clock to I2C module 2 in deep-sleep mode.
382
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
1
D1
RW
0
Description
I2C Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
I2C module 1 is disabled.
1
Enable and provide a clock to I2C module 1 in deep-sleep mode.
I2C Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
I2C module 0 is disabled.
1
Enable and provide a clock to I2C module 0 in deep-sleep mode.
June 12, 2014
383
Texas Instruments-Production Data
System Control
Register 95: Controller Area Network Deep-Sleep Mode Clock Gating Control
(DCGCCAN), offset 0x834
The DCGCCAN register provides software the capability to enable and disable the CAN modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the CAN modules. To support
legacy software, the DCGC0 register is available. A write to the DCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC0 register can be read back correctly with a read of the DCGC0 register. If software
uses this register to write a legacy peripheral (such as CAN0), the write causes proper
operation, but the value of that bit is not reflected in the DCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Controller Area Network Deep-Sleep Mode Clock Gating Control (DCGCCAN)
Base 0x400F.E000
Offset 0x834
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
RW
0
CAN Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
CAN module 1 is disabled.
1
Enable and provide a clock to CAN module 1 in deep-sleep
mode.
CAN Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
CAN module 0 is disabled.
1
Enable and provide a clock to CAN module 0 in deep-sleep
mode.
384
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 96: Analog-to-Digital Converter Deep-Sleep Mode Clock Gating
Control (DCGCADC), offset 0x838
The DCGCADC register provides software the capability to enable and disable the ADC modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the ADC modules. To support
legacy software, the DCGC0 register is available. A write to the DCGC0 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC0 register can be read back correctly with a read of the DCGC0 register. If software
uses this register to write a legacy peripheral (such as ADC0), the write causes proper
operation, but the value of that bit is not reflected in the DCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Analog-to-Digital Converter Deep-Sleep Mode Clock Gating Control (DCGCADC)
Base 0x400F.E000
Offset 0x838
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
RW
0
ADC Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
ADC module 1 is disabled.
1
Enable and provide a clock to ADC module 1 in deep-sleep
mode.
ADC Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
ADC module 0 is disabled.
1
Enable and provide a clock to ADC module 0 in deep-sleep
mode.
June 12, 2014
385
Texas Instruments-Production Data
System Control
Register 97: Analog Comparator Deep-Sleep Mode Clock Gating Control
(DCGCACMP), offset 0x83C
The DCGCACMP register provides software the capability to enable and disable the analog
comparator module in deep-sleep mode. When enabled, a module is provided a clock. When
disabled, the clock is disabled to save power. This register provides the same capability as the
legacy Deep-Sleep Mode Clock Gating Control Register n DCGCn registers specifically for the
watchdog modules and has the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the analog comparator module.
To support legacy software, the DCGC1 register is available. Setting any of the COMPn
bits in the DCGC1 register also sets the D0 bit in this register. If any of the COMPn bits
are set by writing to the DCGC1 register, it can be read back correctly when reading
the DCGC1 register. If software uses this register to change the clocking for the analog
comparator module, the write causes proper operation, but the value D0 is not reflected
by the COMPn bits in the DCGC1 register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Analog Comparator Deep-Sleep Mode Clock Gating Control (DCGCACMP)
Base 0x400F.E000
Offset 0x83C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
D0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
RW
0
Analog Comparator Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
Analog comparator module is disabled.
1
Enable and provide a clock to the analog comparator module
in deep-sleep mode.
386
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 98: Pulse Width Modulator Deep-Sleep Mode Clock Gating Control
(DCGCPWM), offset 0x840
The DCGCPWM register provides software the capability to enable and disable the PWM modules
in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is
disabled to save power. This register provides the same capability as the legacy Deep-Sleep Mode
Clock Gating Control Register n DCGCn registers specifically for the watchdog modules and has
the same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the PWM modules. To support
legacy software, the DCGC0 register is available. A write to the PWM bit in the DCGC0
register also writes the D0 bit in this register. If the PWM bit is changed by writing to the
DCGC0 register, it can be read back correctly with a read of the DCGC0 register.
Software must use this register to support modules that are not present in the legacy
registers. If software uses this register to write to D0, the write causes proper operation,
but the value of that bit is not reflected in the PWM bit in the DCGC0 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Pulse Width Modulator Deep-Sleep Mode Clock Gating Control (DCGCPWM)
Base 0x400F.E000
Offset 0x840
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
D1
D0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
RW
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
RW
0
PWM Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
PWM module 1 is disabled.
1
Enable and provide a clock to PWM module 1 in deep-sleep
mode.
PWM Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
PWM module 0 is disabled.
1
Enable and provide a clock to PWM module 0 in deep-sleep
mode.
June 12, 2014
387
Texas Instruments-Production Data
System Control
Register 99: Quadrature Encoder Interface Deep-Sleep Mode Clock Gating
Control (DCGCQEI), offset 0x844
The DCGCQEI register provides software the capability to enable and disable the QEI modules in
deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock is disabled
to save power. This register provides the same capability as the legacy Deep-Sleep Mode Clock
Gating Control Register n DCGCn registers specifically for the watchdog modules and has the
same bit polarity as the corresponding DCGCn bits.
Important: This register should be used to control the clocking for the QEI modules. To support
legacy software, the DCGC1 register is available. A write to the DCGC1 register also
writes the corresponding bit in this register. Any bits that are changed by writing to the
DCGC1 register can be read back correctly with a read of the DCGC1 register. If software
uses this register to write a legacy peripheral (such as QEI0), the write causes proper
operation, but the value of that bit is not reflected in the DCGC1 register. If software
uses both legacy and peripheral-specific register accesses, the peripheral-specific
registers must be accessed by read-modify-write operations that affect only peripherals
that are not present in the legacy registers. In this manner, both the peripheral-specific
and legacy registers have coherent information.
Quadrature Encoder Interface Deep-Sleep Mode Clock Gating Control (DCGCQEI)
Base 0x400F.E000
Offset 0x844
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
D1
D0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
D1
RW
0
QEI Module 1 Deep-Sleep Mode Clock Gating Control
Value Description
0
D0
RW
0
0
QEI module 1 is disabled.
1
Enable and provide a clock to QEI module 1 in deep-sleep
mode.
QEI Module 0 Deep-Sleep Mode Clock Gating Control
Value Description
0
QEI module 0 is disabled.
1
Enable and provide a clock to QEI module 0 in deep-sleep
mode.
388
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 100: EEPROM Deep-Sleep Mode Clock Gating Control
(DCGCEEPROM), offset 0x858
The DCGCEEPROM register provides software the capability to enable and disable the EEPROM
module in deep-sleep mode. When enabled, a module is provided a clock. When disabled, the clock
is disabled to save power.
EEPROM Deep-Sleep Mode Clock Gating Control (DCGCEEPROM)
Base 0x400F.E000
Offset 0x858
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
D0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
D0
RW
0
EEPROM Module Deep-Sleep Mode Clock Gating Control
Value Description
0
EEPROM module is disabled.
1
Enable and provide a clock to the EEPROM module in
deep-sleep mode.
June 12, 2014
389
Texas Instruments-Production Data
System Control
Register 101: 32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock
Gating Control (DCGCWTIMER), offset 0x85C
The DCGCWTIMER register provides software the capability to enable and disable 32/64-bit wide
timer modules in deep-sleep mode. When enabled, a module is provided a clock. When disabled,
the clock is disabled to save power. This register provides the same capability as the legacy
Deep-Sleep Mode Clock Gating Control Register n DCGCn registers specifically for the timer
modules and has the same bit polarity as the corresponding DCGCn bits.
32/64-Bit Wide General-Purpose Timer Deep-Sleep Mode Clock Gating Control (DCGCWTIMER)
Base 0x400F.E000
Offset 0x85C
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
D5
D4
D3
D2
D1
D0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
D5
RW
0
32/64-Bit Wide General-Purpose Timer 5 Deep-Sleep Mode Clock Gating
Control
Value Description
4
D4
RW
0
0
32/64-bit wide general-purpose timer module 5 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 5 in deep-sleep mode.
32/64-Bit Wide General-Purpose Timer 4 Deep-Sleep Mode Clock Gating
Control
Value Description
3
D3
RW
0
0
32/64-bit wide general-purpose timer module 4 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 4 in deep-sleep mode.
32/64-Bit Wide General-Purpose Timer 3 Deep-Sleep Mode Clock Gating
Control
Value Description
0
32/64-bit wide general-purpose timer module 3 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 3 in deep-sleep mode.
390
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
D2
RW
0
Description
32/64-Bit Wide General-Purpose Timer 2 Deep-Sleep Mode Clock Gating
Control
Value Description
1
D1
RW
0
0
32/64-bit wide general-purpose timer module 2 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 2 in deep-sleep mode.
32/64-Bit Wide General-Purpose Timer 1 Deep-Sleep Mode Clock Gating
Control
Value Description
0
D0
RW
0
0
32/64-bit wide general-purpose timer module 1 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 1 in deep-sleep mode.
32/64-Bit Wide General-Purpose Timer 0 Deep-Sleep Mode Clock Gating
Control
Value Description
0
32/64-bit wide general-purpose timer module 0 is disabled.
1
Enable and provide a clock to 32/64-bit wide general-purpose
timer module 0 in deep-sleep mode.
June 12, 2014
391
Texas Instruments-Production Data
System Control
Register 102: Watchdog Timer Peripheral Ready (PRWD), offset 0xA00
The PRWD register indicates whether the watchdog modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCWD bit is changed. A reset change is initiated if the
corresponding SRWD bit is changed from 0 to 1.
The PRWD bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Watchdog Timer Peripheral Ready (PRWD)
Base 0x400F.E000
Offset 0xA00
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
Watchdog Timer 1 Peripheral Ready
Value Description
0
R0
RO
0
0
Watchdog module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
Watchdog module 1 is ready for access.
Watchdog Timer 0 Peripheral Ready
Value Description
0
Watchdog module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
Watchdog module 0 is ready for access.
392
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 103: 16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER),
offset 0xA04
The PRTIMER register indicates whether the timer modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCTIMER bit is changed. A reset change is initiated if the
corresponding SRTIMER bit is changed from 0 to 1.
The PRTIMER bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
16/32-Bit General-Purpose Timer Peripheral Ready (PRTIMER)
Base 0x400F.E000
Offset 0xA04
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RO
0
16/32-Bit General-Purpose Timer 5 Peripheral Ready
Value Description
4
R4
RO
0
0
16/32-bit timer module 5 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
16/32-bit timer module 5 is ready for access.
16/32-Bit General-Purpose Timer 4 Peripheral Ready
Value Description
3
R3
RO
0
0
16/32-bit timer module 4 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
16/32-bit timer module 4 is ready for access.
16/32-Bit General-Purpose Timer 3 Peripheral Ready
Value Description
0
16/32-bit timer module 3 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
16/32-bit timer module 3 is ready for access.
June 12, 2014
393
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RO
0
Description
16/32-Bit General-Purpose Timer 2 Peripheral Ready
Value Description
1
R1
RO
0
0
16/32-bit timer module 2 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
16/32-bit timer module 2 is ready for access.
16/32-Bit General-Purpose Timer 1 Peripheral Ready
Value Description
0
R0
RO
0
0
16/32-bit timer module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
16/32-bit timer module 1 is ready for access.
16/32-Bit General-Purpose Timer 0 Peripheral Ready
Value Description
0
16/32-bit timer module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
16/32-bit timer module 0 is ready for access.
394
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 104: General-Purpose Input/Output Peripheral Ready (PRGPIO),
offset 0xA08
The PRGPIO register indicates whether the GPIO modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCGPIO bit is changed. A reset change is initiated if the
corresponding SRGPIO bit is changed from 0 to 1.
The PRGPIO bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
General-Purpose Input/Output Peripheral Ready (PRGPIO)
Base 0x400F.E000
Offset 0xA08
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RO
0
GPIO Port F Peripheral Ready
Value Description
4
R4
RO
0
0
GPIO Port F is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
GPIO Port F is ready for access.
GPIO Port E Peripheral Ready
Value Description
3
R3
RO
0
0
GPIO Port E is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
GPIO Port E is ready for access.
GPIO Port D Peripheral Ready
Value Description
0
GPIO Port D is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
GPIO Port D is ready for access.
June 12, 2014
395
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RO
0
Description
GPIO Port C Peripheral Ready
Value Description
1
R1
RO
0
0
GPIO Port C is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
GPIO Port C is ready for access.
GPIO Port B Peripheral Ready
Value Description
0
R0
RO
0
0
GPIO Port B is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
GPIO Port B is ready for access.
GPIO Port A Peripheral Ready
Value Description
0
GPIO Port A is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
GPIO Port A is ready for access.
396
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 105: Micro Direct Memory Access Peripheral Ready (PRDMA), offset
0xA0C
The PRDMA register indicates whether the μDMA module is ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCDMA bit is changed. A reset change is initiated if the
corresponding SRDMA bit is changed from 0 to 1.
The PRDMA bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Micro Direct Memory Access Peripheral Ready (PRDMA)
Base 0x400F.E000
Offset 0xA0C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
R0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
0
μDMA Module Peripheral Ready
Value Description
0
The μDMA module is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
The μDMA module is ready for access.
June 12, 2014
397
Texas Instruments-Production Data
System Control
Register 106: Hibernation Peripheral Ready (PRHIB), offset 0xA14
The PRHIB register indicates whether the Hibernation module is ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCHIB bit is changed. A reset change is initiated if the
corresponding SRHIB bit is changed from 0 to 1.
The PRHIB bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Hibernation Peripheral Ready (PRHIB)
Base 0x400F.E000
Offset 0xA14
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
1
Hibernation Module Peripheral Ready
Value Description
0
The Hibernation module is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
The Hibernation module is ready for access.
398
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 107: Universal Asynchronous Receiver/Transmitter Peripheral Ready
(PRUART), offset 0xA18
The PRUART register indicates whether the UART modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCUART bit is changed. A reset change is initiated if the
corresponding SRUART bit is changed from 0 to 1.
The PRUART bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Universal Asynchronous Receiver/Transmitter Peripheral Ready (PRUART)
Base 0x400F.E000
Offset 0xA18
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R7
R6
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
7
R7
RO
0
UART Module 7 Peripheral Ready
Value Description
6
R6
RO
0
0
UART module 7 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 7 is ready for access.
UART Module 6 Peripheral Ready
Value Description
5
R5
RO
0
0
UART module 6 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 6 is ready for access.
UART Module 5 Peripheral Ready
Value Description
0
UART module 5 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 5 is ready for access.
June 12, 2014
399
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
4
R4
RO
0
Description
UART Module 4 Peripheral Ready
Value Description
3
R3
RO
0
0
UART module 4 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 4 is ready for access.
UART Module 3 Peripheral Ready
Value Description
2
R2
RO
0
0
UART module 3 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 3 is ready for access.
UART Module 2 Peripheral Ready
Value Description
1
R1
RO
0
0
UART module 2 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 2 is ready for access.
UART Module 1 Peripheral Ready
Value Description
0
R0
RO
0
0
UART module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 1 is ready for access.
UART Module 0 Peripheral Ready
Value Description
0
UART module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
UART module 0 is ready for access.
400
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 108: Synchronous Serial Interface Peripheral Ready (PRSSI), offset
0xA1C
The PRSSI register indicates whether the SSI modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCSSI bit is changed. A reset change is initiated if the
corresponding SRSSI bit is changed from 0 to 1.
The PRSSI bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Synchronous Serial Interface Peripheral Ready (PRSSI)
Base 0x400F.E000
Offset 0xA1C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RO
0
SSI Module 3 Peripheral Ready
Value Description
2
R2
RO
0
0
SSI module 3 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
SSI module 3 is ready for access.
SSI Module 2 Peripheral Ready
Value Description
1
R1
RO
0
0
SSI module 2 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
SSI module 2 is ready for access.
SSI Module 1 Peripheral Ready
Value Description
0
SSI module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
SSI module 1 is ready for access.
June 12, 2014
401
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
RO
0
Description
SSI Module 0 Peripheral Ready
Value Description
0
SSI module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
SSI module 0 is ready for access.
402
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 109: Inter-Integrated Circuit Peripheral Ready (PRI2C), offset 0xA20
The PRI2C register indicates whether the I2C modules are ready to be accessed by software following
a change in status of power, Run mode clocking, or reset. A Run mode clocking change is initiated
if the corresponding RCGCI2C bit is changed. A reset change is initiated if the corresponding SRI2C
bit is changed from 0 to 1.
The PRI2C bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Inter-Integrated Circuit Peripheral Ready (PRI2C)
Base 0x400F.E000
Offset 0xA20
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
3
2
1
0
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
3
R3
RO
0
I2C Module 3 Peripheral Ready
Value Description
2
R2
RO
0
0
I2C module 3 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
I2C module 3 is ready for access.
I2C Module 2 Peripheral Ready
Value Description
1
R1
RO
0
0
I2C module 2 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
I2C module 2 is ready for access.
I2C Module 1 Peripheral Ready
Value Description
0
I2C module 1 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
I2C module 1 is ready for access.
June 12, 2014
403
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
0
R0
RO
0
Description
I2C Module 0 Peripheral Ready
Value Description
0
I2C module 0 is not ready for access. It is unclocked, unpowered,
or in the process of completing a reset sequence.
1
I2C module 0 is ready for access.
404
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 110: Controller Area Network Peripheral Ready (PRCAN), offset
0xA34
The PRCAN register indicates whether the CAN modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCCAN bit is changed. A reset change is initiated if the
corresponding SRCAN bit is changed from 0 to 1.
The PRCAN bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Controller Area Network Peripheral Ready (PRCAN)
Base 0x400F.E000
Offset 0xA34
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
CAN Module 1 Peripheral Ready
Value Description
0
R0
RO
0
0
CAN module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
CAN module 1 is ready for access.
CAN Module 0 Peripheral Ready
Value Description
0
CAN module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
CAN module 0 is ready for access.
June 12, 2014
405
Texas Instruments-Production Data
System Control
Register 111: Analog-to-Digital Converter Peripheral Ready (PRADC), offset
0xA38
The PRADC register indicates whether the ADC modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCADC bit is changed. A reset change is initiated if the
corresponding SRADC bit is changed from 0 to 1.
The PRADC bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Analog-to-Digital Converter Peripheral Ready (PRADC)
Base 0x400F.E000
Offset 0xA38
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
ADC Module 1 Peripheral Ready
Value Description
0
R0
RO
0
0
ADC module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
ADC module 1 is ready for access.
ADC Module 0 Peripheral Ready
Value Description
0
ADC module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
ADC module 0 is ready for access.
406
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 112: Analog Comparator Peripheral Ready (PRACMP), offset 0xA3C
The PRACMP register indicates whether the analog comparator module is ready to be accessed
by software following a change in status of power, Run mode clocking, or reset. A Run mode clocking
change is initiated if the corresponding RCGCACMP bit is changed. A reset change is initiated if
the corresponding SRACMP bit is changed from 0 to 1.
The PRACMP bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Analog Comparator Peripheral Ready (PRACMP)
Base 0x400F.E000
Offset 0xA3C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
0
Analog Comparator Module 0 Peripheral Ready
Value Description
0
The analog comparator module is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
The analog comparator module is ready for access.
June 12, 2014
407
Texas Instruments-Production Data
System Control
Register 113: Pulse Width Modulator Peripheral Ready (PRPWM), offset 0xA40
The PRPWM register indicates whether the PWM modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCPWM bit is changed. A reset change is initiated if the
corresponding SRPWM bit is changed from 0 to 1.
The PRPWM bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Pulse Width Modulator Peripheral Ready (PRPWM)
Base 0x400F.E000
Offset 0xA40
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
1
0
R1
R0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
PWM Module 1 Peripheral Ready
Value Description
0
R0
RO
0
0
PWM module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
PWM module 1 is ready for access.
PWM Module 0 Peripheral Ready
Value Description
0
PWM module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
PWM module 0 is ready for access.
408
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 114: Quadrature Encoder Interface Peripheral Ready (PRQEI), offset
0xA44
The PRQEI register indicates whether the QEI modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCQEI bit is changed. A reset change is initiated if the
corresponding SRQEI bit is changed from 0 to 1.
The PRQEI bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
Quadrature Encoder Interface Peripheral Ready (PRQEI)
Base 0x400F.E000
Offset 0xA44
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
Bit/Field
Name
Type
Reset
Description
31:2
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1
R1
RO
0
QEI Module 1 Peripheral Ready
Value Description
0
R0
RO
0
0
QEI module 1 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
QEI module 1 is ready for access.
QEI Module 0 Peripheral Ready
Value Description
0
QEI module 0 is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
QEI module 0 is ready for access.
June 12, 2014
409
Texas Instruments-Production Data
System Control
Register 115: EEPROM Peripheral Ready (PREEPROM), offset 0xA58
The PREEPROM register indicates whether the EEPROM module is ready to be accessed by
software following a change in status of power, Run mode clocking, or reset. A Run mode clocking
change is initiated if the corresponding RCGCEEPROM bit is changed. A reset change is initiated
if the corresponding SREEPROM bit is changed from 0 to 1.
The PREEPROM bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
EEPROM Peripheral Ready (PREEPROM)
Base 0x400F.E000
Offset 0xA58
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
0
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:1
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
0
R0
RO
0
EEPROM Module Peripheral Ready
Value Description
0
The EEPROM module is not ready for access. It is unclocked,
unpowered, or in the process of completing a reset sequence.
1
The EEPROM module is ready for access.
410
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 116: 32/64-Bit Wide General-Purpose Timer Peripheral Ready
(PRWTIMER), offset 0xA5C
The PRWTIMER register indicates whether the timer modules are ready to be accessed by software
following a change in status of power, Run mode clocking, or reset. A Run mode clocking change
is initiated if the corresponding RCGCWTIMER bit is changed. A reset change is initiated if the
corresponding SRWTIMER bit is changed from 0 to 1.
The PRWTIMER bit is cleared on any of the above events and is not set again until the module is
completely powered, enabled, and internally reset.
32/64-Bit Wide General-Purpose Timer Peripheral Ready (PRWTIMER)
Base 0x400F.E000
Offset 0xA5C
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
R5
R4
R3
R2
R1
R0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
Bit/Field
Name
Type
Reset
Description
31:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
5
R5
RO
0
32/64-Bit Wide General-Purpose Timer 5 Peripheral Ready
Value Description
4
R4
RO
0
0
32/64-bit wide timer module 5 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
32/64-bit wide timer module 5 is ready for access.
32/64-Bit Wide General-Purpose Timer 4 Peripheral Ready
Value Description
3
R3
RO
0
0
32/64-bit wide timer module 4 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
32/64-bit wide timer module 4 is ready for access.
32/64-Bit Wide General-Purpose Timer 3 Peripheral Ready
Value Description
0
32/64-bit wide timer module 3 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
32/64-bit wide timer module 3 is ready for access.
June 12, 2014
411
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
R2
RO
0
Description
32/64-Bit Wide General-Purpose Timer 2 Peripheral Ready
Value Description
1
R1
RO
0
0
32/64-bit wide timer module 2 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
32/64-bit wide timer module 2 is ready for access.
32/64-Bit Wide General-Purpose Timer 1 Peripheral Ready
Value Description
0
R0
RO
0
0
32/64-bit wide timer module 1 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
32/64-bit wide timer module 1 is ready for access.
32/64-Bit Wide General-Purpose Timer 0 Peripheral Ready
Value Description
5.6
0
32/64-bit wide timer module 0 is not ready for access. It is
unclocked, unpowered, or in the process of completing a reset
sequence.
1
32/64-bit wide timer module 0 is ready for access.
System Control Legacy Register Descriptions
All addresses given are relative to the System Control base address of 0x400F.E000.
Important: Register in this section are provided for legacy software support only; registers in
“System Control Register Descriptions” on page 231 should be used instead.
412
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 117: Device Capabilities 0 (DC0), offset 0x008
This legacy register is predefined by the part and can be used to verify features.
Important: This register is provided for legacy software support only.
The Flash Size (FSIZE) and SRAM Size (SSIZE) registers should be used to determine
this microcontroller's memory sizes. A read of DC0 correctly identifies legacy memory
sizes but software must use FSIZE and SSIZE for memory sizes that are not listed
below.
Device Capabilities 0 (DC0)
Base 0x400F.E000
Offset 0x008
Type RO, reset 0x007F.003F
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
SRAMSZ
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
FLASHSZ
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
Description
31:16
SRAMSZ
RO
0x7F
SRAM Size
Indicates the size of the on-chip SRAM.
Value Description
0x7
2 KB of SRAM
0xF
4 KB of SRAM
0x17 6 KB of SRAM
0x1F 8 KB of SRAM
0x2F 12 KB of SRAM
0x3F 16 KB of SRAM
0x4F 20 KB of SRAM
0x5F 24 KB of SRAM
0x7F 32 KB of SRAM
June 12, 2014
413
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
Description
15:0
FLASHSZ
RO
0x3F
Flash Size
Indicates the size of the on-chip Flash memory.
Value Description
0x3
8 KB of Flash
0x7
16 KB of Flash
0xF
32 KB of Flash
0x1F 64 KB of Flash
0x2F 96 KB of Flash
0x3F 128 KB of Flash
0x5F 192 KB of Flash
0x7F 256 KB of Flash
414
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 118: Device Capabilities 1 (DC1), offset 0x010
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC0, SCGC0, DCGC0, and the
peripheral-specific RCGC, SCGC, and DCGC registers cannot be set.
Important: This register is provided for legacy software support only.
The Peripheral Present registers should be used to determine which modules are
implemented on this microcontroller. A read of DC1 correctly identifies if a legacy module
is present but software must use the Peripheral Present registers to determine if a
module is present that is not supported by the DCn registers.
Likewise, the ADC Peripheral Properties (ADCPP) register should be used to determine
the maximum ADC sample rate and whether the temperature sensor is present. However,
to support legacy software, the MAXADCnSPD fields and the TEMPSNS bit are available.
A read of DC1 correctly identifies the maximum ADC sample rate for legacy rates and
whether the temperature sensor is present.
Device Capabilities 1 (DC1)
Base 0x400F.E000
Offset 0x010
Type RO, reset 0x1333.2FFF
31
30
29
reserved
Type
Reset
28
WDT1
26
24
23
22
20
19
18
16
CAN1
CAN0
PWM1
PWM0
ADC1
ADC0
RO
1
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
1
RO
1
RO
0
RO
0
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
MPU
HIB
TEMPSNS
PLL
WDT0
SWO
SWD
JTAG
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
MAXADC1SPD
MAXADC0SPD
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x1
RO
1
reserved
17
RO
0
RO
0
reserved
21
RO
0
RO
1
reserved
25
RO
0
MINSYSDIV
Type
Reset
27
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Watchdog Timer1 Present
When set, indicates that watchdog timer 1 is present.
27:26
reserved
RO
0
25
CAN1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN Module 1 Present
When set, indicates that CAN unit 1 is present.
24
CAN0
RO
0x1
CAN Module 0 Present
When set, indicates that CAN unit 0 is present.
23:22
reserved
RO
0
21
PWM1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Module 1 Present
When set, indicates that the PWM module is present.
June 12, 2014
415
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
20
PWM0
RO
0x1
Description
PWM Module 0 Present
When set, indicates that the PWM module is present.
19:18
reserved
RO
0
17
ADC1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC Module 1 Present
When set, indicates that ADC module 1 is present.
16
ADC0
RO
0x1
ADC Module 0 Present
When set, indicates that ADC module 0 is present
15:12
MINSYSDIV
RO
0x2
System Clock Divider
Minimum 4-bit divider value for system clock. The reset value is
hardware-dependent. See the RCC register for how to change the
system clock divisor using the SYSDIV bit.
Value Description
11:10
MAXADC1SPD
RO
0x3
0x1
Reserved
0x2
Specifies an 80-MHz CPU clock with a PLL divider of 2.5.
0x3
Specifies a 50-MHz CPU clock with a PLL divider of 4.
0x4
Specifies a 40-MHz CPU clock with a PLL divider of 5.
0x7
Specifies a 25-MHz clock with a PLL divider of 8.
0x9
Specifies a 20-MHz clock with a PLL divider of 10.
Max ADC1 Speed
This field indicates the maximum rate at which the ADC samples data.
Value Description
9:8
MAXADC0SPD
RO
0x3
0x3
1M samples/second
0x2
500K samples/second
0x1
250K samples/second
0x0
125K samples/second
Max ADC0 Speed
This field indicates the maximum rate at which the ADC samples data.
Value Description
7
MPU
RO
0x1
0x3
1M samples/second
0x2
500K samples/second
0x1
250K samples/second
0x0
125K samples/second
MPU Present
When set, indicates that the Cortex-M4F Memory Protection Unit (MPU)
module is present. See the "Cortex-M4F Peripherals" chapter for details
on the MPU.
416
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
6
HIB
RO
0x1
Description
Hibernation Module Present
When set, indicates that the Hibernation module is present.
5
TEMPSNS
RO
0x1
Temp Sensor Present
When set, indicates that the on-chip temperature sensor is present.
4
PLL
RO
0x1
PLL Present
When set, indicates that the on-chip Phase Locked Loop (PLL) is
present.
3
WDT0
RO
0x1
Watchdog Timer 0 Present
When set, indicates that watchdog timer 0 is present.
2
SWO
RO
0x1
SWO Trace Port Present
When set, indicates that the Serial Wire Output (SWO) trace port is
present.
1
SWD
RO
0x1
SWD Present
When set, indicates that the Serial Wire Debugger (SWD) is present.
0
JTAG
RO
0x1
JTAG Present
When set, indicates that the JTAG debugger interface is present.
June 12, 2014
417
Texas Instruments-Production Data
System Control
Register 119: Device Capabilities 2 (DC2), offset 0x014
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC1, SCGC1, DCGC1, and the
peripheral-specific RCGC, SCGC, and DCGC registers registers cannot be set.
Important: This register is provided for legacy software support only.
The Peripheral Present registers should be used to determine which modules are
implemented on this microcontroller. A read of DC2 correctly identifies if a legacy module
is present but software must use the Peripheral Present registers to determine if a
module is present that is not supported by the DCn registers.
Note that the Analog Comparator Peripheral Present (PPACMP) register identifies
whether the analog comparator module is present. The Analog Comparator Peripheral
Properties (ACMPPP) register indicates how many analog comparator blocks are
present in the module.
Device Capabilities 2 (DC2)
Base 0x400F.E000
Offset 0x014
Type RO, reset 0x030F.F337
Type
Reset
Type
Reset
31
30
29
28
27
26
25
24
reserved
EPI0
reserved
I2S0
reserved
COMP2
COMP1
COMP0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
15
14
13
12
11
10
I2C1HS
I2C1
I2C0HS
I2C0
RO
1
RO
1
RO
1
RO
1
reserved
RO
0
RO
0
23
22
RO
1
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
1
RO
1
Bit/Field
Name
Type
Reset
31
reserved
RO
0
30
EPI0
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
1
RO
1
RO
1
RO
1
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
1
RO
1
RO
0
RO
1
RO
1
RO
1
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
EPI Module 0 Present
When set, indicates that EPI module 0 is present.
29
reserved
RO
0
28
I2S0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2S Module 0 Present
When set, indicates that I2S module 0 is present.
27
reserved
RO
0
26
COMP2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator 2 Present
When set, indicates that analog comparator 2 is present.
25
COMP1
RO
0x1
Analog Comparator 1 Present
When set, indicates that analog comparator 1 is present.
418
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
24
COMP0
RO
0x1
Description
Analog Comparator 0 Present
When set, indicates that analog comparator 0 is present.
23:20
reserved
RO
0
19
TIMER3
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer Module 3 Present
When set, indicates that General-Purpose Timer module 3 is present.
18
TIMER2
RO
0x1
Timer Module 2 Present
When set, indicates that General-Purpose Timer module 2 is present.
17
TIMER1
RO
0x1
Timer Module 1 Present
When set, indicates that General-Purpose Timer module 1 is present.
16
TIMER0
RO
0x1
Timer Module 0 Present
When set, indicates that General-Purpose Timer module 0 is present.
15
I2C1HS
RO
0x1
I2C Module 1 Speed
When set, indicates that I2C module 1 can operate in high-speed mode.
14
I2C1
RO
0x1
I2C Module 1 Present
When set, indicates that I2C module 1 is present.
13
I2C0HS
RO
0x1
I2C Module 0 Speed
When set, indicates that I2C module 0 can operate in high-speed mode.
12
I2C0
RO
0x1
I2C Module 0 Present
When set, indicates that I2C module 0 is present.
11:10
reserved
RO
0
9
QEI1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI Module 1 Present
When set, indicates that QEI module 1 is present.
8
QEI0
RO
0x1
QEI Module 0 Present
When set, indicates that QEI module 0 is present.
7:6
reserved
RO
0
5
SSI1
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI Module 1 Present
When set, indicates that SSI module 1 is present.
4
SSI0
RO
0x1
SSI Module 0 Present
When set, indicates that SSI module 0 is present.
3
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
419
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
UART2
RO
0x1
Description
UART Module 2 Present
When set, indicates that UART module 2 is present.
1
UART1
RO
0x1
UART Module 1 Present
When set, indicates that UART module 1 is present.
0
UART0
RO
0x1
UART Module 0 Present
When set, indicates that UART module 0 is present.
420
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 120: Device Capabilities 3 (DC3), offset 0x018
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the feature is not present.
Important: This register is provided for legacy software support only.
For some modules, the peripheral-resident Peripheral Properties registers should be
used to determine which pins are available on this microcontroller. A read of DC3
correctly identifies if a legacy pin is present but software must use the Peripheral
Properties registers to determine if a pin is present that is not supported by the DCn
registers.
Device Capabilities 3 (DC3)
Base 0x400F.E000
Offset 0x018
Type RO, reset 0xBFFF.8FFF
Type
Reset
Type
Reset
31
30
29
28
27
26
25
24
32KHZ
reserved
CCP5
CCP4
CCP3
CCP2
CCP1
CCP0
RO
1
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
13
12
10
9
15
14
PWMFAULT
C2O
RO
1
RO
0
C2PLUS C2MINUS
RO
0
RO
0
11
C1O
C1PLUS C1MINUS
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31
32KHZ
RO
0x1
23
8
C0O
22
21
20
19
18
17
16
ADC0AIN7 ADC0AIN6 ADC0AIN5 ADC0AIN4 ADC0AIN3 ADC0AIN2 ADC0AIN1 ADC0AIN0
RO
1
RO
1
7
6
C0PLUS C0MINUS
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
5
4
3
2
1
0
PWM5
PWM4
PWM3
PWM2
PWM1
PWM0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
32KHz Input Clock Available
When set, indicates an even CCP pin is present and can be used as a
32-KHz input clock.
Note:
30
reserved
RO
0
29
CCP5
RO
0x1
The GPTMPP register does not provide this information.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
T2CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T2CCP1 is present.
Note:
28
CCP4
RO
0x1
The GPTMPP register does not provide this information.
T2CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T2CCP0 is present.
Note:
27
CCP3
RO
0x1
The GPTMPP register does not provide this information.
T1CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T1CCP1 is present.
Note:
26
CCP2
RO
0x1
The GPTMPP register does not provide this information.
T1CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T1CCP0 is present.
Note:
The GPTMPP register does not provide this information.
June 12, 2014
421
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
25
CCP1
RO
0x1
Description
T0CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T0CCP1 is present.
Note:
24
CCP0
RO
0x1
The GPTMPP register does not provide this information.
T0CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T0CCP0 is present.
Note:
23
ADC0AIN7
RO
0x1
The GPTMPP register does not provide this information.
ADC Module 0 AIN7 Pin Present
When set, indicates that ADC module 0 input pin 7 is present.
Note:
22
ADC0AIN6
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN6 Pin Present
When set, indicates that ADC module 0 input pin 6 is present.
Note:
21
ADC0AIN5
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN5 Pin Present
When set, indicates that ADC module 0 input pin 5 is present.
Note:
20
ADC0AIN4
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN4 Pin Present
When set, indicates that ADC module 0 input pin 4 is present.
Note:
19
ADC0AIN3
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN3 Pin Present
When set, indicates that ADC module 0 input pin 3 is present.
Note:
18
ADC0AIN2
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN2 Pin Present
When set, indicates that ADC module 0 input pin 2 is present.
Note:
17
ADC0AIN1
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN1 Pin Present
When set, indicates that ADC module 0 input pin 1 is present.
Note:
16
ADC0AIN0
RO
0x1
The CH field in the ADCPP register provides this information.
ADC Module 0 AIN0 Pin Present
When set, indicates that ADC module 0 input pin 0 is present.
Note:
15
PWMFAULT
RO
0x1
The CH field in the ADCPP register provides this information.
PWM Fault Pin Present
When set, indicates that a PWM Fault pin is present. See DC5 for
specific Fault pins on this device.
Note:
14
C2O
RO
0x0
The FCNT field in the PWMPP register provides this
information.
C2o Pin Present
When set, indicates that the analog comparator 2 output pin is present.
Note:
The C2O bit in the ACMPPP register provides this information.
422
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
13
C2PLUS
RO
0x0
Description
C2+ Pin Present
When set, indicates that the analog comparator 2 (+) input pin is present.
Note:
12
C2MINUS
RO
0x0
This pin is present when analog comparator 2 is present.
C2- Pin Present
When set, indicates that the analog comparator 2 (-) input pin is present.
Note:
11
C1O
RO
0x1
This pin is present when analog comparator 2 is present.
C1o Pin Present
When set, indicates that the analog comparator 1 output pin is present.
Note:
10
C1PLUS
RO
0x1
The C1O bit in the ACMPPP register provides this information.
C1+ Pin Present
When set, indicates that the analog comparator 1 (+) input pin is present.
Note:
9
C1MINUS
RO
0x1
This pin is present when analog comparator 1 is present.
C1- Pin Present
When set, indicates that the analog comparator 1 (-) input pin is present.
Note:
8
C0O
RO
0x1
This pin is present when analog comparator 1 is present.
C0o Pin Present
When set, indicates that the analog comparator 0 output pin is present.
Note:
7
C0PLUS
RO
0x1
The C0O bit in the ACMPPP register provides this information.
C0+ Pin Present
When set, indicates that the analog comparator 0 (+) input pin is present.
Note:
6
C0MINUS
RO
0x1
This pin is present when analog comparator 0 is present.
C0- Pin Present
When set, indicates that the analog comparator 0 (-) input pin is present.
Note:
5
PWM5
RO
0x1
This pin is present when analog comparator 0 is present.
PWM5 Pin Present
When set, indicates that the PWM pin 5 is present.
Note:
4
PWM4
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM4 Pin Present
When set, indicates that the PWM pin 4 is present.
Note:
3
PWM3
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM3 Pin Present
When set, indicates that the PWM pin 3 is present.
Note:
The GCNT field in the PWMPP register provides this
information.
June 12, 2014
423
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
2
PWM2
RO
0x1
Description
PWM2 Pin Present
When set, indicates that the PWM pin 2 is present.
Note:
1
PWM1
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM1 Pin Present
When set, indicates that the PWM pin 1 is present.
Note:
0
PWM0
RO
0x1
The GCNT field in the PWMPP register provides this
information.
PWM0 Pin Present
When set, indicates that the PWM pin 0 is present.
Note:
The GCNT field in the PWMPP register provides this
information.
424
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 121: Device Capabilities 4 (DC4), offset 0x01C
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC2, SCGC2, DCGC2, and the
peripheral-specific RCGC, SCGC, and DCGC registers registers cannot be set.
Important: This register is provided for legacy software support only.
The Peripheral Present registers should be used to determine which modules are
implemented on this microcontroller. A read of DC4 correctly identifies if a legacy module
is present but software must use the Peripheral Present registers to determine if a
module is present that is not supported by the DCn registers.
The peripheral-resident Peripheral Properties registers should be used to determine
which pins and features are available on this microcontroller. A read of DC4 correctly
identifies if a legacy pin or feature is present. Software must use the Peripheral Properties
registers to determine if a pin or feature is present that is not supported by the DCn
registers.
Device Capabilities 4 (DC4)
Base 0x400F.E000
Offset 0x01C
Type RO, reset 0x0004.F03F
Type
Reset
Type
Reset
31
30
29
28
27
26
25
reserved
EPHY0
reserved
EMAC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
CCP7
CCP6
UDMA
ROM
RO
1
RO
1
RO
1
RO
1
reserved
RO
0
23
22
20
19
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOJ
RO
0
GPIOH
GPIOG
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
E1588
reserved
RO
0
24
RO
0
Bit/Field
Name
Type
Reset
31
reserved
RO
0
30
EPHY0
RO
0x0
21
reserved
18
17
PICAL
16
reserved
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Ethernet PHY Layer 0 Present
When set, indicates that Ethernet PHY layer 0 is present.
29
reserved
RO
0
28
EMAC0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Ethernet MAC Layer 0 Present
When set, indicates that Ethernet MAC layer 0 is present.
27:25
reserved
RO
0
24
E1588
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
1588 Capable
When set, indicates that Ethernet MAC layer 0 is 1588 capable.
June 12, 2014
425
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
23:19
reserved
RO
0
18
PICAL
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PIOSC Calibrate
When set, indicates that the PIOSC can be calibrated by software.
17:16
reserved
RO
0
15
CCP7
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
T3CCP1 Pin Present
When set, indicates that Capture/Compare/PWM pin T3CCP1 is present.
Note:
14
CCP6
RO
0x1
The GPTMPP register does not provide this information.
T3CCP0 Pin Present
When set, indicates that Capture/Compare/PWM pin T3CCP0 is present.
Note:
13
UDMA
RO
0x1
The GPTMPP register does not provide this information.
Micro-DMA Module Present
When set, indicates that the micro-DMA module present.
12
ROM
RO
0x1
Internal Code ROM Present
When set, indicates that internal code ROM is present.
11:9
reserved
RO
0
8
GPIOJ
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
GPIO Port J Present
When set, indicates that GPIO Port J is present.
7
GPIOH
RO
0x0
GPIO Port H Present
When set, indicates that GPIO Port H is present.
6
GPIOG
RO
0x0
GPIO Port G Present
When set, indicates that GPIO Port G is present.
5
GPIOF
RO
0x1
GPIO Port F Present
When set, indicates that GPIO Port F is present.
4
GPIOE
RO
0x1
GPIO Port E Present
When set, indicates that GPIO Port E is present.
3
GPIOD
RO
0x1
GPIO Port D Present
When set, indicates that GPIO Port D is present.
2
GPIOC
RO
0x1
GPIO Port C Present
When set, indicates that GPIO Port C is present.
1
GPIOB
RO
0x1
GPIO Port B Present
When set, indicates that GPIO Port B is present.
426
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
GPIOA
RO
0x1
Description
GPIO Port A Present
When set, indicates that GPIO Port A is present.
June 12, 2014
427
Texas Instruments-Production Data
System Control
Register 122: Device Capabilities 5 (DC5), offset 0x020
This register is predefined by the part and can be used to verify PWM features. If any bit is clear in
this register, the module is not present.
Important: This register is provided for legacy software support only.
The PWM Peripheral Properties (PWMPP) register should be used to determine what
pins and features are available on PWM modules. A read of this register correctly
identifies if a legacy pin or feature is present. Software must use the PWMPP register
to determine if a pin or feature that is not supported by the DCn registers is present.
Device Capabilities 5 (DC5)
Base 0x400F.E000
Offset 0x020
Type RO, reset 0x0130.00FF
31
30
29
28
reserved
Type
Reset
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
23
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:28
reserved
RO
0
27
PWMFAULT3
RO
0x0
RO
0
22
reserved
PWMFAULT3 PWMFAULT2 PWMFAULT1 PWMFAULT0
RO
0
21
20
19
18
PWMEFLT PWMESYNC
RO
0
RO
1
RO
1
17
16
reserved
RO
0
RO
0
RO
0
RO
0
7
6
5
4
3
2
1
0
PWM7
PWM6
PWM5
PWM4
PWM3
PWM2
PWM1
PWM0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Fault 3 Pin Present
When set, indicates that the PWM Fault 3 pin is present.
26
PWMFAULT2
RO
0x0
PWM Fault 2 Pin Present
When set, indicates that the PWM Fault 2 pin is present.
25
PWMFAULT1
RO
0x0
PWM Fault 1 Pin Present
When set, indicates that the PWM Fault 1 pin is present.
24
PWMFAULT0
RO
0x1
PWM Fault 0 Pin Present
When set, indicates that the PWM Fault 0 pin is present.
23:22
reserved
RO
0
21
PWMEFLT
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Extended Fault Active
When set, indicates that the PWM Extended Fault feature is active.
20
PWMESYNC
RO
0x1
PWM Extended SYNC Active
When set, indicates that the PWM Extended SYNC feature is active.
19:8
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
428
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
7
PWM7
RO
0x1
Description
PWM7 Pin Present
When set, indicates that the PWM pin 7 is present.
6
PWM6
RO
0x1
PWM6 Pin Present
When set, indicates that the PWM pin 6 is present.
5
PWM5
RO
0x1
PWM5 Pin Present
When set, indicates that the PWM pin 5 is present.
4
PWM4
RO
0x1
PWM4 Pin Present
When set, indicates that the PWM pin 4 is present.
3
PWM3
RO
0x1
PWM3 Pin Present
When set, indicates that the PWM pin 3 is present.
2
PWM2
RO
0x1
PWM2 Pin Present
When set, indicates that the PWM pin 2 is present.
1
PWM1
RO
0x1
PWM1 Pin Present
When set, indicates that the PWM pin 1 is present.
0
PWM0
RO
0x1
PWM0 Pin Present
When set, indicates that the PWM pin 0 is present.
June 12, 2014
429
Texas Instruments-Production Data
System Control
Register 123: Device Capabilities 6 (DC6), offset 0x024
This register is predefined by the part and can be used to verify features. If any bit is clear in this
register, the module is not present. The corresponding bit in the RCGC0, SCGC0, and DCGC0
registers cannot be set.
Important: This register is provided for legacy software support only.
The USB Peripheral Properties (USBPP) register should be used to determine what
features are available on the USB module. A read of this register correctly identifies if
a legacy feature is present. Software must use the USBPP register to determine if a
pin or feature that is not supported by the DCn registers is present.
Device Capabilities 6 (DC6)
Base 0x400F.E000
Offset 0x024
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
10
9
8
7
6
5
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
USB0PHY
RO
0
Bit/Field
Name
Type
Reset
31:5
reserved
RO
0
4
USB0PHY
RO
0x0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
RO
0
RO
0
0
USB0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
USB Module 0 PHY Present
When set, indicates that the USB module 0 PHY is present.
3:2
reserved
RO
0
1:0
USB0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
USB Module 0 Present
This field indicates that USB module 0 is present and specifies its
capability.
sysValue Description
0x0
NA
USB0 is not present.
0x1
DEVICE
USB0 is Device Only.
0x2
HOST
USB0 is Device or Host.
0x3
OTG
USB0 is OTG.
430
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 124: Device Capabilities 7 (DC7), offset 0x028
This register is predefined by the part and can be used to verify μDMA channel features. A 1 indicates
the channel is available on this device; a 0 that the channel is only available on other devices in the
family. Channels can have multiple assignments, see “Channel Assignments” on page 574 for more
information.
Important: This register is provided for legacy software support only. The DMACHANS bit field in
the DMA Status (DMASTAT) register indicates the number of DMA channels.
Device Capabilities 7 (DC7)
Base 0x400F.E000
Offset 0x028
Type RO, reset 0xFFFF.FFFF
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
reserved DMACH30 DMACH29 DMACH28 DMACH27 DMACH26 DMACH25 DMACH24 DMACH23 DMACH22 DMACH21 DMACH20 DMACH19 DMACH18 DMACH17 DMACH16
Type
Reset
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
DMACH15 DMACH14 DMACH13 DMACH12 DMACH11 DMACH10 DMACH9 DMACH8 DMACH7 DMACH6 DMACH5 DMACH4 DMACH3 DMACH2 DMACH1 DMACH0
Type
Reset
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Bit/Field
Name
Type
Reset
31
reserved
RO
0x1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
DMA Channel 31
When set, indicates μDMA channel 31 is available.
30
DMACH30
RO
0x1
DMA Channel 30
When set, indicates μDMA channel 30 is available.
29
DMACH29
RO
0x1
DMA Channel 29
When set, indicates μDMA channel 29 is available.
28
DMACH28
RO
0x1
DMA Channel 28
When set, indicates μDMA channel 28 is available.
27
DMACH27
RO
0x1
DMA Channel 27
When set, indicates μDMA channel 27 is available.
26
DMACH26
RO
0x1
DMA Channel 26
When set, indicates μDMA channel 26 is available.
25
DMACH25
RO
0x1
DMA Channel 25
When set, indicates μDMA channel 25 is available.
24
DMACH24
RO
0x1
DMA Channel 24
When set, indicates μDMA channel 24 is available.
23
DMACH23
RO
0x1
DMA Channel 23
When set, indicates μDMA channel 23 is available.
22
DMACH22
RO
0x1
DMA Channel 22
When set, indicates μDMA channel 22 is available.
June 12, 2014
431
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
21
DMACH21
RO
0x1
Description
DMA Channel 21
When set, indicates μDMA channel 21 is available.
20
DMACH20
RO
0x1
DMA Channel 20
When set, indicates μDMA channel 20 is available.
19
DMACH19
RO
0x1
DMA Channel 19
When set, indicates μDMA channel 19 is available.
18
DMACH18
RO
0x1
DMA Channel 18
When set, indicates μDMA channel 18 is available.
17
DMACH17
RO
0x1
DMA Channel 17
When set, indicates μDMA channel 17 is available.
16
DMACH16
RO
0x1
DMA Channel 16
When set, indicates μDMA channel 16 is available.
15
DMACH15
RO
0x1
DMA Channel 15
When set, indicates μDMA channel 15 is available.
14
DMACH14
RO
0x1
DMA Channel 14
When set, indicates μDMA channel 14 is available.
13
DMACH13
RO
0x1
DMA Channel 13
When set, indicates μDMA channel 13 is available.
12
DMACH12
RO
0x1
DMA Channel 12
When set, indicates μDMA channel 12 is available.
11
DMACH11
RO
0x1
DMA Channel 11
When set, indicates μDMA channel 11 is available.
10
DMACH10
RO
0x1
DMA Channel 10
When set, indicates μDMA channel 10 is available.
9
DMACH9
RO
0x1
DMA Channel 9
When set, indicates μDMA channel 9 is available.
8
DMACH8
RO
0x1
DMA Channel 8
When set, indicates μDMA channel 8 is available.
7
DMACH7
RO
0x1
DMA Channel 7
When set, indicates μDMA channel 7 is available.
6
DMACH6
RO
0x1
DMA Channel 6
When set, indicates μDMA channel 6 is available.
5
DMACH5
RO
0x1
DMA Channel 5
When set, indicates μDMA channel 5 is available.
4
DMACH4
RO
0x1
DMA Channel 4
When set, indicates μDMA channel 4 is available.
432
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
DMACH3
RO
0x1
Description
DMA Channel 3
When set, indicates μDMA channel 3 is available.
2
DMACH2
RO
0x1
DMA Channel 2
When set, indicates μDMA channel 2 is available.
1
DMACH1
RO
0x1
DMA Channel 1
When set, indicates μDMA channel 1 is available.
0
DMACH0
RO
0x1
DMA Channel 0
When set, indicates μDMA channel 0 is available.
June 12, 2014
433
Texas Instruments-Production Data
System Control
Register 125: Device Capabilities 8 (DC8), offset 0x02C
This register is predefined by the part and can be used to verify features.
Important: This register is provided for legacy software support only.
The ADC Peripheral Properties (ADCPP) register should be used to determine how
many input channels are available on the ADC module. A read of this register correctly
identifies if legacy channels are present but software must use the ADCPP register to
determine if a channel is present that is not supported by the DCn registers.
Device Capabilities 8 (DC8)
Base 0x400F.E000
Offset 0x02C
Type RO, reset 0x0FFF.0FFF
Type
Reset
Type
Reset
31
30
29
28
27
26
ADC1AIN15
ADC1AIN14
ADC1AIN13
ADC1AIN12
ADC1AIN11
ADC1AIN10
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
15
14
13
12
11
10
ADC0AIN15
ADC0AIN14
ADC0AIN13
ADC0AIN12
ADC0AIN11
ADC0AIN10
RO
0
RO
0
RO
0
RO
0
RO
1
RO
1
25
24
23
22
21
20
19
18
17
16
ADC1AIN9 ADC1AIN8 ADC1AIN7 ADC1AIN6 ADC1AIN5 ADC1AIN4 ADC1AIN3 ADC1AIN2 ADC1AIN1 ADC1AIN0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
9
8
7
6
5
4
3
2
1
0
ADC0AIN9 ADC0AIN8 ADC0AIN7 ADC0AIN6 ADC0AIN5 ADC0AIN4 ADC0AIN3 ADC0AIN2 ADC0AIN1 ADC0AIN0
RO
1
Bit/Field
Name
Type
Reset
31
ADC1AIN15
RO
0x0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
ADC Module 1 AIN15 Pin Present
When set, indicates that ADC module 1 input pin 15 is present.
30
ADC1AIN14
RO
0x0
ADC Module 1 AIN14 Pin Present
When set, indicates that ADC module 1 input pin 14 is present.
29
ADC1AIN13
RO
0x0
ADC Module 1 AIN13 Pin Present
When set, indicates that ADC module 1 input pin 13 is present.
28
ADC1AIN12
RO
0x0
ADC Module 1 AIN12 Pin Present
When set, indicates that ADC module 1 input pin 12 is present.
27
ADC1AIN11
RO
0x1
ADC Module 1 AIN11 Pin Present
When set, indicates that ADC module 1 input pin 11 is present.
26
ADC1AIN10
RO
0x1
ADC Module 1 AIN10 Pin Present
When set, indicates that ADC module 1 input pin 10 is present.
25
ADC1AIN9
RO
0x1
ADC Module 1 AIN9 Pin Present
When set, indicates that ADC module 1 input pin 9 is present.
24
ADC1AIN8
RO
0x1
ADC Module 1 AIN8 Pin Present
When set, indicates that ADC module 1 input pin 8 is present.
23
ADC1AIN7
RO
0x1
ADC Module 1 AIN7 Pin Present
When set, indicates that ADC module 1 input pin 7 is present.
22
ADC1AIN6
RO
0x1
ADC Module 1 AIN6 Pin Present
When set, indicates that ADC module 1 input pin 6 is present.
434
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
21
ADC1AIN5
RO
0x1
Description
ADC Module 1 AIN5 Pin Present
When set, indicates that ADC module 1 input pin 5 is present.
20
ADC1AIN4
RO
0x1
ADC Module 1 AIN4 Pin Present
When set, indicates that ADC module 1 input pin 4 is present.
19
ADC1AIN3
RO
0x1
ADC Module 1 AIN3 Pin Present
When set, indicates that ADC module 1 input pin 3 is present.
18
ADC1AIN2
RO
0x1
ADC Module 1 AIN2 Pin Present
When set, indicates that ADC module 1 input pin 2 is present.
17
ADC1AIN1
RO
0x1
ADC Module 1 AIN1 Pin Present
When set, indicates that ADC module 1 input pin 1 is present.
16
ADC1AIN0
RO
0x1
ADC Module 1 AIN0 Pin Present
When set, indicates that ADC module 1 input pin 0 is present.
15
ADC0AIN15
RO
0x0
ADC Module 0 AIN15 Pin Present
When set, indicates that ADC module 0 input pin 15 is present.
14
ADC0AIN14
RO
0x0
ADC Module 0 AIN14 Pin Present
When set, indicates that ADC module 0 input pin 14 is present.
13
ADC0AIN13
RO
0x0
ADC Module 0 AIN13 Pin Present
When set, indicates that ADC module 0 input pin 13 is present.
12
ADC0AIN12
RO
0x0
ADC Module 0 AIN12 Pin Present
When set, indicates that ADC module 0 input pin 12 is present.
11
ADC0AIN11
RO
0x1
ADC Module 0 AIN11 Pin Present
When set, indicates that ADC module 0 input pin 11 is present.
10
ADC0AIN10
RO
0x1
ADC Module 0 AIN10 Pin Present
When set, indicates that ADC module 0 input pin 10 is present.
9
ADC0AIN9
RO
0x1
ADC Module 0 AIN9 Pin Present
When set, indicates that ADC module 0 input pin 9 is present.
8
ADC0AIN8
RO
0x1
ADC Module 0 AIN8 Pin Present
When set, indicates that ADC module 0 input pin 8 is present.
7
ADC0AIN7
RO
0x1
ADC Module 0 AIN7 Pin Present
When set, indicates that ADC module 0 input pin 7 is present.
6
ADC0AIN6
RO
0x1
ADC Module 0 AIN6 Pin Present
When set, indicates that ADC module 0 input pin 6 is present.
5
ADC0AIN5
RO
0x1
ADC Module 0 AIN5 Pin Present
When set, indicates that ADC module 0 input pin 5 is present.
4
ADC0AIN4
RO
0x1
ADC Module 0 AIN4 Pin Present
When set, indicates that ADC module 0 input pin 4 is present.
June 12, 2014
435
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
ADC0AIN3
RO
0x1
Description
ADC Module 0 AIN3 Pin Present
When set, indicates that ADC module 0 input pin 3 is present.
2
ADC0AIN2
RO
0x1
ADC Module 0 AIN2 Pin Present
When set, indicates that ADC module 0 input pin 2 is present.
1
ADC0AIN1
RO
0x1
ADC Module 0 AIN1 Pin Present
When set, indicates that ADC module 0 input pin 1 is present.
0
ADC0AIN0
RO
0x1
ADC Module 0 AIN0 Pin Present
When set, indicates that ADC module 0 input pin 0 is present.
436
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 126: Software Reset Control 0 (SRCR0), offset 0x040
This register allows individual modules to be reset. Writes to this register are masked by the bits in
the Device Capabilities 1 (DC1) register.
Important: This register is provided for legacy software support only.
The peripheral-specific Software Reset registers (such as SRWD) should be used to
reset specific peripherals. A write to this legacy register also writes the corresponding
bit in the peripheral-specific register. Any bits that are changed by writing to this legacy
register can be read back correctly with a read of this register. Software must use the
peripheral-specific registers to support modules that are not present in the legacy
registers. If software uses a peripheral-specific register to write a legacy peripheral
(such as Watchdog 1), the write causes proper operation, but the value of that bit is not
reflected in this register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Software Reset Control 0 (SRCR0)
Base 0x400F.E000
Offset 0x040
Type RO, reset 0x0000.0000
31
30
29
reserved
Type
Reset
28
WDT1
RO
0
RO
0
RO
0
RO
0
15
14
13
12
27
26
reserved
25
24
CAN1
CAN0
23
RO
0
RO
0
RO
0
RO
0
RO
0
11
10
9
8
7
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
22
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
0
RO
0
20
RO
0
RO
0
6
5
4
RO
0
19
PWM0
RO
0
HIB
RO
0
21
reserved
reserved
RO
0
RO
0
18
reserved
RO
0
RO
0
3
2
WDT0
RO
0
17
16
ADC1
ADC0
RO
0
RO
0
1
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Reset Control
When this bit is set, Watchdog Timer module 1 is reset. All internal data
is lost and the registers are returned to their reset states. This bit must
be manually cleared after being set.
27:26
reserved
RO
0
25
CAN1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Reset Control
When this bit is set, CAN module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
24
CAN0
RO
0x0
CAN0 Reset Control
When this bit is set, CAN module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
June 12, 2014
437
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
23:21
reserved
RO
0
20
PWM0
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Reset Control
When this bit is set, PWM module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
19:18
reserved
RO
0
17
ADC1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Reset Control
When this bit is set, ADC module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
16
ADC0
RO
0x0
ADC0 Reset Control
When this bit is set, ADC module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
15:7
reserved
RO
0
6
HIB
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Reset Control
When this bit is set, the Hibernation module is reset. All internal data is
lost and the registers are returned to their reset states. This bit must be
manually cleared after being set.
5:4
reserved
RO
0
3
WDT0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT0 Reset Control
When this bit is set, Watchdog Timer module 0 is reset. All internal data
is lost and the registers are returned to their reset states. This bit must
be manually cleared after being set.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
438
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 127: Software Reset Control 1 (SRCR1), offset 0x044
This register allows individual modules to be reset. Writes to this register are masked by the bits in
the Device Capabilities 2 (DC2) register.
Important: This register is provided for legacy software support only.
The peripheral-specific Software Reset registers (such as SRTIMER) should be used
to reset specific peripherals. A write to this register also writes the corresponding bit in
the peripheral-specific register. Any bits that are changed by writing to this register can
be read back correctly with a read of this register. Software must use the
peripheral-specific registers to support modules that are not present in the legacy
registers. If software uses a peripheral-specific register to write a legacy peripheral
(such as TIMER0), the write causes proper operation, but the value of that bit is not
reflected in this register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Note that the Software Reset Analog Comparator (SRACMP) register has only one
bit to set the analog comparator module. Resetting the module resets all the blocks. If
any of the COMPn bits are set, the entire analog comparator module is reset. It is not
possible to reset the blocks individually.
Software Reset Control 1 (SRCR1)
Base 0x400F.E000
Offset 0x044
Type RO, reset 0x0000.0000
31
30
29
RO
0
RO
0
RO
0
15
14
reserved
RO
0
28
27
26
RO
0
RO
0
RO
0
13
12
11
10
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
reserved
RO
0
RO
0
25
24
23
22
COMP1
COMP0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:26
reserved
RO
0
25
COMP1
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comp 1 Reset Control
When this bit is set, Analog Comparator module 1 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
24
COMP0
RO
0x0
Analog Comp 0 Reset Control
When this bit is set, Analog Comparator module 0 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
23:20
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
439
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
19
TIMER3
RO
0x0
Description
Timer 3 Reset Control
Timer 3 Reset Control. When this bit is set, General-Purpose Timer
module 3 is reset. All internal data is lost and the registers are returned
to their reset states. This bit must be manually cleared after being set.
18
TIMER2
RO
0x0
Timer 2 Reset Control
When this bit is set, General-Purpose Timer module 2 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
17
TIMER1
RO
0x0
Timer 1 Reset Control
When this bit is set, General-Purpose Timer module 1 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
16
TIMER0
RO
0x0
Timer 0 Reset Control
When this bit is set, General-Purpose Timer module 0 is reset. All internal
data is lost and the registers are returned to their reset states. This bit
must be manually cleared after being set.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Reset Control
When this bit is set, I2C module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
13
reserved
RO
0
12
I2C0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C0 Reset Control
When this bit is set, I2C module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
11:10
reserved
RO
0
9
QEI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI1 Reset Control
When this bit is set, QEI module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
8
QEI0
RO
0x0
QEI0 Reset Control
When this bit is set, QEI module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
7:6
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
440
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
5
SSI1
RO
0x0
Description
SSI1 Reset Control
When this bit is set, SSI module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
4
SSI0
RO
0x0
SSI0 Reset Control
When this bit is set, SSI module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Reset Control
When this bit is set, UART module 2 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
1
UART1
RO
0x0
UART1 Reset Control
When this bit is set, UART module 1 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
0
UART0
RO
0x0
UART0 Reset Control
When this bit is set, UART module 0 is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
June 12, 2014
441
Texas Instruments-Production Data
System Control
Register 128: Software Reset Control 2 (SRCR2), offset 0x048
This register allows individual modules to be reset. Writes to this register are masked by the bits in
the Device Capabilities 4 (DC4) register.
Important: This register is provided for legacy software support only.
The peripheral-specific Software Reset registers (such as SRDMA) should be used to
reset specific peripherals. A write to this legacy register also writes the corresponding
bit in the peripheral-specific register. Any bits that are changed by writing to this register
can be read back correctly with a read of this register. Software must use the
peripheral-specific registers to support modules that are not present in the legacy
registers. If software uses a peripheral-specific register to write a legacy peripheral
(such as the μDMA), the write causes proper operation, but the value of that bit is not
reflected in this register. If software uses both legacy and peripheral-specific register
accesses, the peripheral-specific registers must be accessed by read-modify-write
operations that affect only peripherals that are not present in the legacy registers. In
this manner, both the peripheral-specific and legacy registers have coherent information.
Software Reset Control 2 (SRCR2)
Base 0x400F.E000
Offset 0x048
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
RO
0
RO
0
15
14
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
13
12
11
10
UDMA
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
reserved
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
13
UDMA
RO
0x0
RO
0
RO
0
5
4
3
2
1
0
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Micro-DMA Reset Control
When this bit is set, uDMA module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
12:6
reserved
RO
0
5
GPIOF
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port F Reset Control
When this bit is set, Port F module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
4
GPIOE
RO
0x0
Port E Reset Control
When this bit is set, Port E module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
442
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
GPIOD
RO
0x0
Description
Port D Reset Control
When this bit is set, Port D module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
2
GPIOC
RO
0x0
Port C Reset Control
When this bit is set, Port C module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
1
GPIOB
RO
0x0
Port B Reset Control
When this bit is set, Port B module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
0
GPIOA
RO
0x0
Port A Reset Control
When this bit is set, Port A module is reset. All internal data is lost and
the registers are returned to their reset states. This bit must be manually
cleared after being set.
June 12, 2014
443
Texas Instruments-Production Data
System Control
Register 129: Run Mode Clock Gating Control Register 0 (RCGC0), offset
0x100
This register controls the clock gating logic in normal Run mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC0 is the clock configuration register for
running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes. Note that there must be a delay of 3 system clocks after a module clock is enabled before
any registers in that module are accessed.
Important: This register is provided for legacy software support only.
The peripheral-specific Run Mode Clock Gating Control registers (such as RCGCWD)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as Watchdog 1), the write causes proper operation, but the value of
that bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Likewise, the ADC Peripheral Configuration (ADCPC) register should be used to
configure the ADC sample rate. However, to support legacy software, the MAXADCnSPD
fields are available. A write to these legacy fields also writes the corresponding field in
the peripheral-specific register. If a field is changed by writing to this register, it can be
read back correctly with a read of this register. Software must use the peripheral-specific
registers to support rates that are not available in this register. If software uses a
peripheral-specific register to set the ADC rate, the write causes proper operation, but
the value of that field is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
444
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Run Mode Clock Gating Control Register 0 (RCGC0)
Base 0x400F.E000
Offset 0x100
Type RO, reset 0x0000.0040
31
30
29
reserved
Type
Reset
28
WDT1
26
24
23
22
21
19
16
CAN1
CAN0
ADC1
ADC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
reserved
HIB
RO
0
RO
0
RO
0
RO
1
MAXADC0SPD
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
0
reserved
RO
0
RO
0
reserved
17
RO
0
MAXADC1SPD
PWM0
18
RO
0
RO
0
reserved
20
RO
0
RO
0
reserved
25
RO
0
reserved
Type
Reset
27
WDT0
RO
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 1. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
27:26
reserved
RO
0
25
CAN1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Clock Gating Control
This bit controls the clock gating for CAN module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
24
CAN0
RO
0x0
CAN0 Clock Gating Control
This bit controls the clock gating for CAN module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
23:21
reserved
RO
0
20
PWM0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Clock Gating Control
This bit controls the clock gating for the PWM module. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
19:18
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
445
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
17
ADC1
RO
0x0
Description
ADC1 Clock Gating Control
This bit controls the clock gating for SAR ADC module 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
16
ADC0
RO
0x0
ADC0 Clock Gating Control
This bit controls the clock gating for ADC module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
15:12
reserved
RO
0
11:10
MAXADC1SPD
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Sample Speed
This field sets the rate at which ADC module 1 samples data. You cannot
set the rate higher than the maximum rate. You can set the sample rate
by setting the MAXADC1SPD bit as follows (all other encodings are
reserved):
Value Description
9:8
MAXADC0SPD
RO
0x0
0x0
125K samples/second
0x1
250K samples/second
0x2
500K samples/second
0x3
1M samples/second
ADC0 Sample Speed
This field sets the rate at which ADC0 samples data. You cannot set
the rate higher than the maximum rate. You can set the sample rate by
setting the MAXADC0SPD bit as follows (all other encodings are reserved):
Value Description
7
reserved
RO
0
6
HIB
RO
0x1
0x0
125K samples/second
0x1
250K samples/second
0x2
500K samples/second
0x3
1M samples/second
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Clock Gating Control
This bit controls the clock gating for the Hibernation module. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
5:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
446
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
3
WDT0
RO
0x0
Description
WDT0 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 0. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
447
Texas Instruments-Production Data
System Control
Register 130: Run Mode Clock Gating Control Register 1 (RCGC1), offset
0x104
This register controls the clock gating logic in normal Run mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC1 is the clock configuration register for
running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes. Note that there must be a delay of 3 system clocks after a module clock is enabled before
any registers in that module are accessed.
Important: This register is provided for legacy software support only.
The peripheral-specific Run Mode Clock Gating Control registers (such as RCGCTIMER)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as Timer 0), the write causes proper operation, but the value of that
bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Run Mode Clock Gating Control Register 1 (RCGC1)
Base 0x400F.E000
Offset 0x104
Type RO, reset 0x0000.0000
31
30
29
RO
0
RO
0
RO
0
15
14
reserved
RO
0
28
27
26
RO
0
RO
0
RO
0
13
12
11
10
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
reserved
RO
0
RO
0
25
24
23
22
COMP1
COMP0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:26
reserved
RO
0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
448
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
25
COMP1
RO
0x0
Description
Analog Comparator 1 Clock Gating
This bit controls the clock gating for analog comparator 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
24
COMP0
RO
0x0
Analog Comparator 0 Clock Gating
This bit controls the clock gating for analog comparator 0. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
18
TIMER2
RO
0x0
Timer 2 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 2.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
17
TIMER1
RO
0x0
Timer 1 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 1.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
16
TIMER0
RO
0x0
Timer 0 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 0.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Clock Gating Control
This bit controls the clock gating for I2C module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
13
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
449
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
12
I2C0
RO
0x0
Description
I2C0 Clock Gating Control
This bit controls the clock gating for I2C module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
11:10
reserved
RO
0
9
QEI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
QEI1 Clock Gating Control
This bit controls the clock gating for QEI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
8
QEI0
RO
0x0
QEI0 Clock Gating Control
This bit controls the clock gating for QEI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Clock Gating Control
This bit controls the clock gating for SSI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
4
SSI0
RO
0x0
SSI0 Clock Gating Control
This bit controls the clock gating for SSI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Clock Gating Control
This bit controls the clock gating for UART module 2. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
1
UART1
RO
0x0
UART1 Clock Gating Control
This bit controls the clock gating for UART module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
450
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
0
UART0
RO
0x0
Description
UART0 Clock Gating Control
This bit controls the clock gating for UART module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
June 12, 2014
451
Texas Instruments-Production Data
System Control
Register 131: Run Mode Clock Gating Control Register 2 (RCGC2), offset
0x108
This register controls the clock gating logic in normal Run mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC2 is the clock configuration register for
running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes. Note that there must be a delay of 3 system clocks after a module clock is enabled before
any registers in that module are accessed.
Important: This register is provided for legacy software support only.
The peripheral-specific Run Mode Clock Gating Control registers (such as RCGCDMA)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as the μDMA), the write causes proper operation, but the value of that
bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Run Mode Clock Gating Control Register 2 (RCGC2)
Base 0x400F.E000
Offset 0x108
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
UDMA
RO
0
reserved
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
452
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
13
UDMA
RO
0x0
Description
Micro-DMA Clock Gating Control
This bit controls the clock gating for micro-DMA. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
12:6
reserved
RO
0
5
GPIOF
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port F Clock Gating Control
This bit controls the clock gating for Port F. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
4
GPIOE
RO
0x0
Port E Clock Gating Control
Port E Clock Gating Control. This bit controls the clock gating for Port
E. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
3
GPIOD
RO
0x0
Port D Clock Gating Control
Port D Clock Gating Control. This bit controls the clock gating for Port
D. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
2
GPIOC
RO
0x0
Port C Clock Gating Control
This bit controls the clock gating for Port C. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
1
GPIOB
RO
0x0
Port B Clock Gating Control
This bit controls the clock gating for Port B. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
0
GPIOA
RO
0x0
Port A Clock Gating Control
This bit controls the clock gating for Port A. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
June 12, 2014
453
Texas Instruments-Production Data
System Control
Register 132: Sleep Mode Clock Gating Control Register 0 (SCGC0), offset
0x110
This register controls the clock gating logic in Sleep mode. Each bit controls a clock enable for a
given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC0 is the clock configuration register for
running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Sleep Mode Clock Gating Control registers (such as SCGCWD)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as Watchdog 1), the write causes proper operation, but the value of
that bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Sleep Mode Clock Gating Control Register 0 (SCGC0)
Base 0x400F.E000
Offset 0x110
Type RO, reset 0x0000.0040
31
30
29
reserved
Type
Reset
28
WDT1
27
26
reserved
25
24
23
21
reserved
20
19
16
CAN1
CAN0
ADC1
ADC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
HIB
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
1
reserved
RO
0
RO
0
reserved
17
RO
0
RO
0
PWM0
18
RO
0
reserved
Type
Reset
22
WDT0
RO
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Clock Gating Control
This bit controls the clock gating for Watchdog Timer module 1. If set,
the module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
454
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
27:26
reserved
RO
0
25
CAN1
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Clock Gating Control
This bit controls the clock gating for CAN module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
24
CAN0
RO
0x0
CAN0 Clock Gating Control
This bit controls the clock gating for CAN module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
23:21
reserved
RO
0
20
PWM0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Clock Gating Control
This bit controls the clock gating for the PWM module. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
19:18
reserved
RO
0
17
ADC1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Clock Gating Control
This bit controls the clock gating for ADC module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
16
ADC0
RO
0x0
ADC0 Clock Gating Control
This bit controls the clock gating for ADC module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
15:7
reserved
RO
0
6
HIB
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Clock Gating Control
This bit controls the clock gating for the Hibernation module. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
5:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
455
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
WDT0
RO
0x0
Description
WDT0 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 0. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
456
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 133: Sleep Mode Clock Gating Control Register 1 (SCGC1), offset
0x114
This register controls the clock gating logic in Sleep mode. Each bit controls a clock enable for a
given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC1 is the clock configuration register for
running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Sleep Mode Clock Gating Control registers (such as
SCGCTIMER) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as Timer 0), the write causes proper operation, but the value
of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Sleep Mode Clock Gating Control Register 1 (SCGC1)
Base 0x400F.E000
Offset 0x114
Type RO, reset 0x0000.0000
31
30
29
RO
0
RO
0
RO
0
15
14
reserved
RO
0
28
27
26
RO
0
RO
0
RO
0
13
12
11
10
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
reserved
RO
0
RO
0
25
24
23
22
COMP1
COMP0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:26
reserved
RO
0
25
COMP1
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator 1 Clock Gating
This bit controls the clock gating for analog comparator 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
June 12, 2014
457
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
24
COMP0
RO
0x0
Description
Analog Comparator 0 Clock Gating
This bit controls the clock gating for analog comparator 0. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
18
TIMER2
RO
0x0
Timer 2 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 2.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
17
TIMER1
RO
0x0
Timer 1 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 1.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
16
TIMER0
RO
0x0
Timer 0 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 0.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Clock Gating Control
This bit controls the clock gating for I2C module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
13
reserved
RO
0
12
I2C0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C0 Clock Gating Control
This bit controls the clock gating for I2C module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
11:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
458
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
9
QEI1
RO
0x0
Description
QEI1 Clock Gating Control
This bit controls the clock gating for QEI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
8
QEI0
RO
0x0
QEI0 Clock Gating Control
This bit controls the clock gating for QEI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Clock Gating Control
This bit controls the clock gating for SSI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
4
SSI0
RO
0x0
SSI0 Clock Gating Control
This bit controls the clock gating for SSI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Clock Gating Control
This bit controls the clock gating for UART module 2. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
1
UART1
RO
0x0
UART1 Clock Gating Control
This bit controls the clock gating for UART module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
0
UART0
RO
0x0
UART0 Clock Gating Control
This bit controls the clock gating for UART module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
June 12, 2014
459
Texas Instruments-Production Data
System Control
Register 134: Sleep Mode Clock Gating Control Register 2 (SCGC2), offset
0x118
This register controls the clock gating logic in Sleep mode. Each bit controls a clock enable for a
given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC2 is the clock configuration register for
running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Sleep Mode Clock Gating Control registers (such as SCGCDMA)
should be used to reset specific peripherals. A write to this legacy register also writes
the corresponding bit in the peripheral-specific register. Any bits that are changed by
writing to this register can be read back correctly with a read of this register. Software
must use the peripheral-specific registers to support modules that are not present in
the legacy registers. If software uses a peripheral-specific register to write a legacy
peripheral (such as the μDMA), the write causes proper operation, but the value of that
bit is not reflected in this register. If software uses both legacy and peripheral-specific
register accesses, the peripheral-specific registers must be accessed by
read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Sleep Mode Clock Gating Control Register 2 (SCGC2)
Base 0x400F.E000
Offset 0x118
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
UDMA
RO
0
reserved
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
13
UDMA
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Micro-DMA Clock Gating Control
This bit controls the clock gating for micro-DMA. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
460
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
12:6
reserved
RO
0
5
GPIOF
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port F Clock Gating Control
This bit controls the clock gating for Port F. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
4
GPIOE
RO
0x0
Port E Clock Gating Control
Port E Clock Gating Control. This bit controls the clock gating for Port
E. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
3
GPIOD
RO
0x0
Port D Clock Gating Control
Port D Clock Gating Control. This bit controls the clock gating for Port
D. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
2
GPIOC
RO
0x0
Port C Clock Gating Control
This bit controls the clock gating for Port C. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
1
GPIOB
RO
0x0
Port B Clock Gating Control
This bit controls the clock gating for Port B. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
0
GPIOA
RO
0x0
Port A Clock Gating Control
This bit controls the clock gating for Port A. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
June 12, 2014
461
Texas Instruments-Production Data
System Control
Register 135: Deep Sleep Mode Clock Gating Control Register 0 (DCGC0),
offset 0x120
This register controls the clock gating logic in Deep-Sleep mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC0 is the clock configuration register for
running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Deep Sleep Mode Clock Gating Control registers (such as
DCGCWD) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as Watchdog 1), the write causes proper operation, but the
value of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Deep Sleep Mode Clock Gating Control Register 0 (DCGC0)
Base 0x400F.E000
Offset 0x120
Type RO, reset 0x0000.0040
31
30
29
reserved
Type
Reset
28
WDT1
27
26
reserved
25
24
23
21
reserved
20
19
16
CAN1
CAN0
ADC1
ADC0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
HIB
Bit/Field
Name
Type
Reset
31:29
reserved
RO
0
28
WDT1
RO
0x0
RO
1
reserved
RO
0
RO
0
reserved
17
RO
0
RO
0
PWM0
18
RO
0
reserved
Type
Reset
22
WDT0
RO
0
reserved
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
WDT1 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 1. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
462
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
27:26
reserved
RO
0
25
CAN1
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
CAN1 Clock Gating Control
This bit controls the clock gating for CAN module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
24
CAN0
RO
0x0
CAN0 Clock Gating Control
This bit controls the clock gating for CAN module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
23:21
reserved
RO
0
20
PWM0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
PWM Clock Gating Control
This bit controls the clock gating for the PWM module. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
19:18
reserved
RO
0
17
ADC1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 Clock Gating Control
This bit controls the clock gating for ADC module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
16
ADC0
RO
0x0
ADC0 Clock Gating Control
This bit controls the clock gating for ADC module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
15:7
reserved
RO
0
6
HIB
RO
0x1
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
HIB Clock Gating Control
This bit controls the clock gating for the Hibernation module. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
5:4
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
June 12, 2014
463
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
3
WDT0
RO
0x0
Description
WDT0 Clock Gating Control
This bit controls the clock gating for the Watchdog Timer module 0. If
set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
2:0
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
464
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Register 136: Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1),
offset 0x124
This register controls the clock gating logic in Deep-Sleep mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC1 is the clock configuration register for
running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Deep Sleep Mode Clock Gating Control registers (such as
DCGCTIMER) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as Timer 0), the write causes proper operation, but the value
of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Deep-Sleep Mode Clock Gating Control Register 1 (DCGC1)
Base 0x400F.E000
Offset 0x124
Type RO, reset 0x0000.0000
31
30
29
RO
0
RO
0
RO
0
15
14
reserved
RO
0
28
27
26
RO
0
RO
0
RO
0
13
12
11
10
I2C1
reserved
I2C0
RO
0
RO
0
RO
0
reserved
Type
Reset
Type
Reset
reserved
RO
0
RO
0
25
24
23
22
COMP1
COMP0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
9
8
7
6
5
QEI1
QEI0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:26
reserved
RO
0
25
COMP1
RO
0x0
21
20
19
18
17
16
TIMER3
TIMER2
TIMER1
TIMER0
RO
0
RO
0
RO
0
RO
0
4
3
2
1
0
SSI1
SSI0
reserved
UART2
UART1
UART0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
reserved
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Analog Comparator 1 Clock Gating
This bit controls the clock gating for analog comparator 1. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
June 12, 2014
465
Texas Instruments-Production Data
System Control
Bit/Field
Name
Type
Reset
24
COMP0
RO
0x0
Description
Analog Comparator 0 Clock Gating
This bit controls the clock gating for analog comparator 0. If set, the
module receives a clock and functions. Otherwise, the module is
unclocked and disabled. If the module is unclocked, a read or write to
the module generates a bus fault.
23:20
reserved
RO
0
19
TIMER3
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
18
TIMER2
RO
0x0
Timer 2 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 2.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
17
TIMER1
RO
0x0
Timer 1 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 1.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
16
TIMER0
RO
0x0
Timer 0 Clock Gating Control
This bit controls the clock gating for General-Purpose Timer module 0.
If set, the module receives a clock and functions. Otherwise, the module
is unclocked and disabled. If the module is unclocked, a read or write
to the module generates a bus fault.
15
reserved
RO
0
14
I2C1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C1 Clock Gating Control
This bit controls the clock gating for I2C module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
13
reserved
RO
0
12
I2C0
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
I2C0 Clock Gating Control
This bit controls the clock gating for I2C module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
11:10
reserved
RO
0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
466
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
9
QEI1
RO
0x0
Description
QEI1 Clock Gating Control
This bit controls the clock gating for QEI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
8
QEI0
RO
0x0
QEI0 Clock Gating Control
This bit controls the clock gating for QEI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
7:6
reserved
RO
0
5
SSI1
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
SSI1 Clock Gating Control
This bit controls the clock gating for SSI module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
4
SSI0
RO
0x0
SSI0 Clock Gating Control
This bit controls the clock gating for SSI module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
3
reserved
RO
0
2
UART2
RO
0x0
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
UART2 Clock Gating Control
This bit controls the clock gating for UART module 2. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
1
UART1
RO
0x0
UART1 Clock Gating Control
This bit controls the clock gating for UART module 1. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
0
UART0
RO
0x0
UART0 Clock Gating Control
This bit controls the clock gating for UART module 0. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
June 12, 2014
467
Texas Instruments-Production Data
System Control
Register 137: Deep Sleep Mode Clock Gating Control Register 2 (DCGC2),
offset 0x128
This register controls the clock gating logic in Deep-Sleep mode. Each bit controls a clock enable
for a given interface, function, or module. If set, the module receives a clock and functions. Otherwise,
the module is unclocked and disabled (saving power). If the module is unclocked, reads or writes
to the module generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise
noted, so that all functional modules are disabled. It is the responsibility of software to enable the
ports necessary for the application. Note that these registers may contain more bits than there are
interfaces, functions, or modules to control. This configuration is implemented to assure reasonable
code compatibility with other family and future parts. RCGC2 is the clock configuration register for
running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the
ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep
modes.
Important: This register is provided for legacy software support only.
The peripheral-specific Deep Sleep Mode Clock Gating Control registers (such as
DCGCDMA) should be used to reset specific peripherals. A write to this legacy register
also writes the corresponding bit in the peripheral-specific register. Any bits that are
changed by writing to this register can be read back correctly with a read of this register.
Software must use the peripheral-specific registers to support modules that are not
present in the legacy registers. If software uses a peripheral-specific register to write a
legacy peripheral (such as the μDMA), the write causes proper operation, but the value
of that bit is not reflected in this register. If software uses both legacy and
peripheral-specific register accesses, the peripheral-specific registers must be accessed
by read-modify-write operations that affect only peripherals that are not present in the
legacy registers. In this manner, both the peripheral-specific and legacy registers have
coherent information.
Deep Sleep Mode Clock Gating Control Register 2 (DCGC2)
Base 0x400F.E000
Offset 0x128
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
GPIOF
GPIOE
GPIOD
GPIOC
GPIOB
GPIOA
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
RO
0
UDMA
RO
0
reserved
RO
0
Bit/Field
Name
Type
Reset
31:14
reserved
RO
0
13
UDMA
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Micro-DMA Clock Gating Control
This bit controls the clock gating for micro-DMA. If set, the module
receives a clock and functions. Otherwise, the module is unclocked and
disabled. If the module is unclocked, a read or write to the module
generates a bus fault.
468
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
12:6
reserved
RO
0
5
GPIOF
RO
0x0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Port F Clock Gating Control
This bit controls the clock gating for Port F. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
4
GPIOE
RO
0x0
Port E Clock Gating Control
Port E Clock Gating Control. This bit controls the clock gating for Port
E. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
3
GPIOD
RO
0x0
Port D Clock Gating Control
Port D Clock Gating Control. This bit controls the clock gating for Port
D. If set, the module receives a clock and functions. Otherwise, the
module is unclocked and disabled. If the module is unclocked, a read
or write to the module generates a bus fault.
2
GPIOC
RO
0x0
Port C Clock Gating Control
This bit controls the clock gating for Port C. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
1
GPIOB
RO
0x0
Port B Clock Gating Control
This bit controls the clock gating for Port B. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
0
GPIOA
RO
0x0
Port A Clock Gating Control
This bit controls the clock gating for Port A. If set, the module receives
a clock and functions. Otherwise, the module is unclocked and disabled.
If the module is unclocked, a read or write to the module generates a
bus fault.
June 12, 2014
469
Texas Instruments-Production Data
System Control
Register 138: Device Capabilities 9 (DC9), offset 0x190
This register is predefined by the part and can be used to verify ADC digital comparator features.
Important: This register is provided for legacy software support only.
The ADC Peripheral Properties (ADCPP) register should be used to determine how
many digital comparators are available on the ADC module. A read of this register
correctly identifies if legacy comparators are present. Software must use the ADCPP
register to determine if a comparator that is not supported by the DCn registers is
present.
Device Capabilities 9 (DC9)
Base 0x400F.E000
Offset 0x190
Type RO, reset 0x00FF.00FF
31
30
29
28
27
26
25
24
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
ADC1DC7 ADC1DC6 ADC1DC5 ADC1DC4 ADC1DC3 ADC1DC2 ADC1DC1 ADC1DC0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
7
6
5
4
3
2
1
0
ADC0DC7 ADC0DC6 ADC0DC5 ADC0DC4 ADC0DC3 ADC0DC2 ADC0DC1 ADC0DC0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:24
reserved
RO
0
23
ADC1DC7
RO
0x1
RO
0
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC1 DC7 Present
When set, indicates that ADC module 1 Digital Comparator 7 is present.
22
ADC1DC6
RO
0x1
ADC1 DC6 Present
When set, indicates that ADC module 1 Digital Comparator 6 is present.
21
ADC1DC5
RO
0x1
ADC1 DC5 Present
When set, indicates that ADC module 1 Digital Comparator 5 is present.
20
ADC1DC4
RO
0x1
ADC1 DC4 Present
When set, indicates that ADC module 1 Digital Comparator 4 is present.
19
ADC1DC3
RO
0x1
ADC1 DC3 Present
When set, indicates that ADC module 1 Digital Comparator 3 is present.
18
ADC1DC2
RO
0x1
ADC1 DC2 Present
When set, indicates that ADC module 1 Digital Comparator 2 is present.
17
ADC1DC1
RO
0x1
ADC1 DC1 Present
When set, indicates that ADC module 1 Digital Comparator 1 is present.
16
ADC1DC0
RO
0x1
ADC1 DC0 Present
When set, indicates that ADC module 1 Digital Comparator 0 is present.
470
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
15:8
reserved
RO
0
7
ADC0DC7
RO
0x1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
ADC0 DC7 Present
When set, indicates that ADC module 0 Digital Comparator 7 is present.
6
ADC0DC6
RO
0x1
ADC0 DC6 Present
When set, indicates that ADC module 0 Digital Comparator 6 is present.
5
ADC0DC5
RO
0x1
ADC0 DC5 Present
When set, indicates that ADC module 0 Digital Comparator 5 is present.
4
ADC0DC4
RO
0x1
ADC0 DC4 Present
When set, indicates that ADC module 0 Digital Comparator 4 is present.
3
ADC0DC3
RO
0x1
ADC0 DC3 Present
When set, indicates that ADC module 0 Digital Comparator 3 is present.
2
ADC0DC2
RO
0x1
ADC0 DC2 Present
When set, indicates that ADC module 0 Digital Comparator 2 is present.
1
ADC0DC1
RO
0x1
ADC0 DC1 Present
When set, indicates that ADC module 0 Digital Comparator 1 is present.
0
ADC0DC0
RO
0x1
ADC0 DC0 Present
When set, indicates that ADC module 0 Digital Comparator 0 is present.
June 12, 2014
471
Texas Instruments-Production Data
System Control
Register 139: Non-Volatile Memory Information (NVMSTAT), offset 0x1A0
This register is predefined by the part and can be used to verify features.
Important: This register is provided for legacy software support only.
The ROM Third-Party Software (ROMSWMAP) register should be used to determine
the presence of third-party software in the on-chip ROM on this microcontroller. A read
of the TPSW bit in this register correctly identifies the presence of legacy third-party
software. Software should use the ROMSWMAP register for software that is not on
legacy devices.
Non-Volatile Memory Information (NVMSTAT)
Base 0x400F.E000
Offset 0x1A0
Type RO, reset 0x0000.0001
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Bit/Field
Name
Type
Reset
31:1
reserved
RO
0
0
FWB
RO
0x1
RO
0
0
FWB
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
1
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
32 Word Flash Write Buffer Available
When set, indicates that the 32 word Flash memory write buffer feature
is available.
472
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
6
System Exception Module
This module is an AHB peripheral that handles system-level Cortex-M4 FPU exceptions. For functions
with registers mapped into this aperture, if the function is not available on a device, then all writes
to the associated registers are ignored and reads return zeros.
6.1
Functional Description
The System Exception module provides control and status of the system-level interrupts. All the
interrupt events are ORed together before being sent to the interrupt controller, so the System
Exception module can only generate a single interrupt request to the controller at any given time.
Software can service multiple interrupt events in a single interrupt service routine by reading the
System Exception Masked Interrupt Status (SYSEXCMIS) register. The interrupt events that can
trigger a controller-level interrupt are defined in the System Exception Interrupt Mask (SYSEXCIM)
register by setting the corresponding interrupt mask bits. If interrupts are not used, the raw interrupt
status is always visible via the System Exception Raw Interrupt Status (SYSEXCRIS) register.
Interrupts are always cleared (for both the SYSEXCMIS and SYSEXCRIS registers) by writing a 1
to the corresponding bit in the System Exception Interrupt Clear (SYSEXCIC) register.
6.2
Register Map
Table 6-1 on page 473 lists the System Exception module registers. The offset listed is a hexadecimal
increment to the register's address, relative to the System Exception base address of 0x400F.9000.
Note:
Spaces in the System Exception register space that are not used are reserved for future or
internal use. Software should not modify any reserved memory address.
Table 6-1. System Exception Register Map
Offset
Name
0x000
Reset
SYSEXCRIS
RO
0x0000.0000
System Exception Raw Interrupt Status
474
0x004
SYSEXCIM
RW
0x0000.0000
System Exception Interrupt Mask
476
0x008
SYSEXCMIS
RO
0x0000.0000
System Exception Masked Interrupt Status
478
0x00C
SYSEXCIC
W1C
0x0000.0000
System Exception Interrupt Clear
480
6.3
Description
See
page
Type
Register Descriptions
All addresses given are relative to the System Exception base address of 0x400F.9000.
June 12, 2014
473
Texas Instruments-Production Data
System Exception Module
Register 1: System Exception Raw Interrupt Status (SYSEXCRIS), offset 0x000
The SYSEXCRIS register is the raw interrupt status register. On a read, this register gives the
current raw status value of the corresponding interrupt. A write has no effect.
System Exception Raw Interrupt Status (SYSEXCRIS)
Base 0x400F.9000
Offset 0x000
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
8
7
6
5
4
3
2
1
0
FPIOCRIS
FPDZCRIS
FPIDCRIS
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
reserved
Type
Reset
reserved
Type
Reset
RO
0
FPIXCRIS
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.00
5
FPIXCRIS
RO
0
RO
0
FPOFCRIS FPUFCRIS
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Floating-Point Inexact Exception Raw Interrupt Status
Value Description
0
No interrupt
1
A floating-point inexact exception has occurred.
This bit is cleared by writing a 1 to the IXCIC bit in the SYSEXCIC
register.
4
FPOFCRIS
RO
0
Floating-Point Overflow Exception Raw Interrupt Status
Value Description
0
No interrupt
1
A floating-point overflow exception has occurred.
This bit is cleared by writing a 1 to the OFCIC bit in the SYSEXCIC
register.
3
FPUFCRIS
RO
0
Floating-Point Underflow Exception Raw Interrupt Status
Value Description
0
No interrupt
1
A floating-point underflow exception has occurred.
This bit is cleared by writing a 1 to the UFCIC bit in the SYSEXCIC
register.
474
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
FPIOCRIS
RO
0
Description
Floating-Point Invalid Operation Raw Interrupt Status
Value Description
0
No interrupt
1
A floating-point invalid operation exception has occurred.
This bit is cleared by writing a 1 to the IOCIC bit in the SYSEXCIC
register.
1
FPDZCRIS
RO
0
Floating-Point Divide By 0 Exception Raw Interrupt Status
Value Description
0
No interrupt
1
A floating-point divide by 0 exception has occurred.
This bit is cleared by writing a 1 to the DZCIC bit in the SYSEXCIC
register.
0
FPIDCRIS
RO
0
Floating-Point Input Denormal Exception Raw Interrupt Status
Value Description
0
No interrupt
1
A floating-point input denormal exception has occurred.
This bit is cleared by writing a 1 to the IDCIC bit in the SYSEXCIC
register.
June 12, 2014
475
Texas Instruments-Production Data
System Exception Module
Register 2: System Exception Interrupt Mask (SYSEXCIM), offset 0x004
The SYSEXCIM register is the interrupt mask set/clear register.
On a read, this register gives the current value of the mask on the relevant interrupt. Setting a bit
allows the corresponding raw interrupt signal to be routed to the interrupt controller. Clearing a bit
prevents the raw interrupt signal from being sent to the interrupt controller.
System Exception Interrupt Mask (SYSEXCIM)
Base 0x400F.9000
Offset 0x004
Type RW, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
5
4
3
2
1
0
reserved
Type
Reset
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
FPIXCIM FPOFCIM FPUFCIM FPIOCIM FPDZCIM FPIDCIM
RW
0
Bit/Field
Name
Type
Reset
31:6
reserved
RW
0x0000.00
5
FPIXCIM
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
RW
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Floating-Point Inexact Exception Interrupt Mask
Value Description
4
FPOFCIM
RW
0
0
The FPIXCRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
FPISCRIS bit in the SYSEXCRIS register is set.
Floating-Point Overflow Exception Interrupt Mask
Value Description
3
FPUFCIM
RW
0
0
The FPOFCIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
FPOFCRIS bit in the SYSEXCRIS register is set.
Floating-Point Underflow Exception Interrupt Mask
Value Description
0
The FPUFCRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
FPUFCRIS bit in the SYSEXCRIS register is set.
476
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
FPIOCIM
RW
0
Description
Floating-Point Invalid Operation Interrupt Mask
Value Description
1
FPDZCIM
RW
0
0
The FPIOCRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
FPIOCRIS bit in the SYSEXCRIS register is set.
Floating-Point Divide By 0 Exception Interrupt Mask
Value Description
0
FPIDCIM
RW
0
0
The FPDZCRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
FPDZCRIS bit in the SYSEXCRIS register is set.
Floating-Point Input Denormal Exception Interrupt Mask
Value Description
0
The FPIDCRIS interrupt is suppressed and not sent to the
interrupt controller.
1
An interrupt is sent to the interrupt controller when the
FPIDCRIS bit in the SYSEXCRIS register is set.
June 12, 2014
477
Texas Instruments-Production Data
System Exception Module
Register 3: System Exception Masked Interrupt Status (SYSEXCMIS), offset
0x008
The SYSEXCMIS register is the masked interrupt status register. On a read, this register gives the
current masked status value of the corresponding interrupt. A write has no effect.
System Exception Masked Interrupt Status (SYSEXCMIS)
Base 0x400F.9000
Offset 0x008
Type RO, reset 0x0000.0000
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
5
4
3
2
1
0
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
15
14
13
12
11
10
9
8
7
6
reserved
Type
Reset
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
FPIXCMIS FPOFCMIS FPUFCMIS FPIOCMIS FPDZCMIS FPIDCMIS
RO
0
Bit/Field
Name
Type
Reset
31:6
reserved
RO
0x0000.00
5
FPIXCMIS
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
RO
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Floating-Point Inexact Exception Masked Interrupt Status
Value Description
0
An interrupt has not occurred or is masked.
1
An unmasked interrupt was signaled due to an inexact
exception.
This bit is cleared by writing a 1 to the FPIXCIC bit in the SYSEXCIC
register.
4
FPOFCMIS
RO
0
Floating-Point Overflow Exception Masked Interrupt Status
Value Description
0
An interrupt has not occurred or is masked.
1
An unmasked interrupt was signaled due to an overflow
exception.
This bit is cleared by writing a 1 to the FPOFCIC bit in the SYSEXCIC
register.
3
FPUFCMIS
RO
0
Floating-Point Underflow Exception Masked Interrupt Status
Value Description
0
An interrupt has not occurred or is masked.
1
An unmasked interrupt was signaled due to an underflow
exception.
This bit is cleared by writing a 1 to the FPUFCIC bit in the SYSEXCIC
register.
478
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Bit/Field
Name
Type
Reset
2
FPIOCMIS
RO
0
Description
Floating-Point Invalid Operation Masked Interrupt Status
Value Description
0
An interrupt has not occurred or is masked.
1
An unmasked interrupt was signaled due to an invalid operation.
This bit is cleared by writing a 1 to the FPIOCIC bit in the SYSEXCIC
register.
1
FPDZCMIS
RO
0
Floating-Point Divide By 0 Exception Masked Interrupt Status
Value Description
0
An interrupt has not occurred or is masked.
1
An unmasked interrupt was signaled due to a divide by 0
exception.
This bit is cleared by writing a 1 to the FPDZCIC bit in the SYSEXCIC
register.
0
FPIDCMIS
RO
0
Floating-Point Input Denormal Exception Masked Interrupt Status
Value Description
0
An interrupt has not occurred or is masked.
1
An unmasked interrupt was signaled due to an input denormal
exception.
This bit is cleared by writing a 1 to the FPIDCIC bit in the SYSEXCIC
register.
June 12, 2014
479
Texas Instruments-Production Data
System Exception Module
Register 4: System Exception Interrupt Clear (SYSEXCIC), offset 0x00C
The SYSEXCIC register is the interrupt clear register. On a write of 1, the corresponding interrupt
(both raw interrupt and masked interrupt, if enabled) is cleared. A write of 0 has no effect.
System Exception Interrupt Clear (SYSEXCIC)
Base 0x400F.9000
Offset 0x00C
Type W1C, reset 0x0000.0000
31
30
29
28
27
26
25
24
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
15
14
13
12
11
10
9
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
23
22
21
20
19
18
17
16
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
8
7
6
5
4
3
2
1
0
W1C
0
W1C
0
W1C
0
reserved
Type
Reset
reserved
Type
Reset
W1C
0
FPIXCIC FPOFCIC FPUFCIC FPIOCIC FPDZCIC FPIDCIC
Bit/Field
Name
Type
Reset
31:6
reserved
W1C
0x0000.00
5
FPIXCIC
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
W1C
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Floating-Point Inexact Exception Interrupt Clear
Writing a 1 to this bit clears the FPIXCRIS bit in the SYSEXCRIS register
and the FPIXCMIS bit in the SYSEXCMIS register.
4
FPOFCIC
W1C
0
Floating-Point Overflow Exception Interrupt Clear
Writing a 1 to this bit clears the FPOFCRIS bit in the SYSEXCRIS register
and the FPOFCMIS bit in the SYSEXCMIS register.
3
FPUFCIC
W1C
0
Floating-Point Underflow Exception Interrupt Clear
Writing a 1 to this bit clears the FPUFCRIS bit in the SYSEXCRIS register
and the FPUFCMIS bit in the SYSEXCMIS register.
2
FPIOCIC
W1C
0
Floating-Point Invalid Operation Interrupt Clear
Writing a 1 to this bit clears the FPIOCRIS bit in the SYSEXCRIS register
and the FPIOCMIS bit in the SYSEXCMIS register.
1
FPDZCIC
W1C
0
Floating-Point Divide By 0 Exception Interrupt Clear
Writing a 1 to this bit clears the FPDZCRIS bit in the SYSEXCRIS register
and the FPDZCMIS bit in the SYSEXCMIS register.
0
FPIDCIC
W1C
0
Floating-Point Input Denormal Exception Interrupt Clear
Writing a 1 to this bit clears the FPIDCRIS bit in the SYSEXCRIS register
and the FPIDCMIS bit in the SYSEXCMIS register.
480
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
7
Hibernation Module
The Hibernation Module manages removal and restoration of power to provide a means for reducing
system power consumption. When the processor and peripherals are idle, power can be completely
removed with only the Hibernation module remaining powered. Power can be restored based on
an external signal or at a certain time using the built-in Real-Time Clock (RTC). The Hibernation
module can be independently supplied from an external battery or an auxiliary power supply.
The Hibernation module has the following features:
■ 32-bit real-time seconds counter (RTC) with 1/32,768 second resolution and a 15-bit sub-seconds
counter
– 32-bit RTC seconds match register and a 15-bit sub seconds match for timed wake-up and
interrupt generation with 1/32,768 second resolution
– RTC predivider trim for making fine adjustments to the clock rate
■ Two mechanisms for power control
– System power control using discrete external regulator
– On-chip power control using internal switches under register control
■ Dedicated pin for waking using an external signal
■ RTC operational and hibernation memory valid as long as VDD or VBAT is valid
■ Low-battery detection, signaling, and interrupt generation, with optional wake on low battery
■ GPIO pin state can be retained during hibernation
■ Clock source from a 32.768-kHz external crystal or oscillator
■ Sixteen 32-bit words of battery-backed memory to save state during hibernation
■ Programmable interrupts for:
– RTC match
– External wake
– Low battery
June 12, 2014
481
Texas Instruments-Production Data
Hibernation Module
7.1
Block Diagram
Figure 7-1. Hibernation Module Block Diagram
HIBCTL.CLK32EN
Clock Source for
System Clock
XOSC0
Pre-Divider
XOSC1
HIBRTCT
RTC
HIBRTCC
HIBRTCLD
HIBRTCM0
HIBRTCSS
Battery-Backed
Memory
16 words
HIBDATA
Interrupts
HIBIM
HIBRIS
HIBMIS
HIBIC
Interrupts
to CPU
MATCH
HIBCTL.RTCEN
WAKE
LOWBAT
Power
Sequence
Logic
Low Battery
Detect
VBAT
HIBCTL.VBATSEL
HIBCTL.RTCWEN
HIBCTL.BATCHK
HIBCTL.PINWEN
HIB
HIBCTL.VABORT
HIBCTL.HIBREQ
HIBCTL.BATWKEN
7.2
Signal Description
The following table lists the external signals of the Hibernation module and describes the function
of each.
Table 7-1. Hibernate Signals (64LQFP)
Pin Name
Pin Number Pin Mux / Pin
Assignment
a
Pin Type
Buffer Type
Description
GNDX
35
fixed
-
Power
GND for the Hibernation oscillator. When using a
crystal clock source, this pin should be connected
to digital ground along with the crystal load
capacitors. When using an external oscillator, this
pin should be connected to digital ground.
HIB
33
fixed
O
TTL
VBAT
37
fixed
-
Power
Power source for the Hibernation module. It is
normally connected to the positive terminal of a
battery and serves as the battery
backup/Hibernation module power-source supply.
WAKE
32
fixed
I
TTL
An external input that brings the processor out of
Hibernate mode when asserted.
An output that indicates the processor is in
Hibernate mode.
482
June 12, 2014
Texas Instruments-Production Data
Tiva™ TM4C123BE6PM Microcontroller
Table 7-1. Hibernate Signals (64LQFP) (continued)
Pin Name
Pin Number Pin Mux / Pin
Assignment
a
Pin Type
Buffer Type
Description
XOSC0
34
fixed
I
Analog
Hibernation module oscillator crystal input or an
external clock reference input. Note that this is
either a 32.768-kHz crystal or a 32.768-kHz
oscillator for the Hibernation module RTC.
XOSC1
36
fixed
O
Analog
Hibernation module oscillator crystal output. Leave
unconnected when using a single-ended clock
source.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.