Minmax ABW-02D83 Ac/dc power module 2w Datasheet

ABW-02 SERIES
AC/DC Power Module 2W
FEATURES
►Fully Encapsulated Plastic Case for PCB Mounting
►Universal Input 85~264VAC, 47~440Hz
►Constant Power Mode, No Output Current Limit
►Protection Class II as per IEC/EN 60536
►Operating Ambient Temp. Range -30°C to +70°C
►Short Circuit Protection
►Designed-in EMI Emission meets EN55011/22 Class B & FCC
Level B
►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11
►Eco Design, Low No Load Power Consumption < 150mW
►UL/cUL/IEC/EN 60950-1, TUV/IEC/EN 60335-1 Safety Approval
& CE Marking
PRODUCT OVERVIEW
The ABW-02 series is a new range of small, fully encapsulated AC/DC power supply modules.They are designed for direct PCB mounting with solder
pins.They feature regulated output voltages which have a constant output power mode instead of a conventional current limit characteristics,which makes
the power modules suitable to drive relays,solenoids,capacitive loads and LED’s.To power logic circuits for standby functions models with an addtional
second, voltage regulated 3.3 or 5VDC output are available.
The ABW-02 power supply modules provide a cost-effective new solution for standby power applications in appliances and consumer electronics.
equipment. Universal input voltage 85-264VAC and International safety approvals including IEC/EN60335-1 qualifies the product for worldwide markets.
Model Selection Guide
Model
Number
Voltage
Output 1
ABW-02S08
ABW-02S14
ABW-02S24
ABW-02D83 ***
ABW-02D85 ***
ABW-02D143 ***
ABW-02D145 ***
VDC
8
14
24
8
8
14
14
Output 2
Voltage
Current
Max.
mA
250
143
83
*
*
**
**
Current
Max.
mA
------160
250
70
83
VDC
------3.3
5
3.3
5
Input Current
Efficiency
(typ.)
@Max. Load
mA(typ.)
42
40
39
43
43
43
43
@Max. Load
%
72
74
76
69
69
70
70
* Io1+Io2≦250mA
** Io1+Io2≦143mA
*** The definition of output power (Po) for dual-output modules : Po=V01 x (I01 + I02 )
Input Specifications
Parameter
Input Voltage Range
Input Frequency Range
Input Voltage Range
No-Load Power Consumption
Input Surge Voltage
Model
Min.
85
47
120
-----
All Models
Typ.
------30
---
Max.
264
440
370
--308
Unit
VAC
Hz
VDC
mW
VAC
Output Specifications
Parameter
Conditions
Output 1
Output Voltage Accuracy
Output 2
Output 1
Line Regulation
Output 2
Output 1
Load Regulation
Output 2
Ripple & Noise
0-20 MHz Bandwidth
Short Circuit Protection
REV:3
Vin=85~264VAC
Io=10% to 100%
Typ.
Max.
Unit
---
---
±5.0
%
---
---
±2.0
%
---
±1.0
---
%
---
±0.3
---
%
---
±1.0
---
%
---
±0.5
---
%
Output 1
---
1
---
V P-P
Output 2
---
0.1
---
V P-P
Continuous, Automatic Recovery
E-mail:[email protected]
2016/06/02
Vin=115VAC, Full Load
Min.
Tel:886-6-2923150
Page 1 of 3
ABW-02 SERIES
AC/DC POWER MODULE 2W
General Specifications
Parameter
Conditions
Min.
Typ.
Max.
Unit
Input to Output, 60 Seconds
3000
---
---
VAC
---
45
---
MIL-HDBK-217F@25℃, Ground Benign
500,000
I/O Isolation Voltage
Switching Frequency
MTBF (calculated)
KHz
Hours
UL/cUL 60950-1 recognition(UL certificate)
IEC/EN 60950-1(CB-report)
IEC/EN 60335-1 recognition(TUV certificata,CB-report)
Safety Approvals
Environmental Specifications
Parameter
Operating Ambient Temperature Range
Storage Temperature Range
Humidity (non condensing)
Cooling
Conditions
Natural Convection
Min.
-30
-40
---
Max.
+70
+85
95
Unit
℃
℃
% rel. H
---
260
℃
Natural Convection
Lead Temperature
(1.5mm from case for 10Sec.)
EMC Specifications
Parameter
Standards & Level
Conduction and Radiation
EN55014-2 ,EN55024
ESD
Radiated immunity
Fast transient
Surge
Conducted immunity
PFMF
Dips
Interruptions
EMI
EMS
Performance
EN55014-1, EN55022, FCC part 15
Class B
EN61000-4-2 Air ± 8kV , Contact ± 4kV
EN61000-4-3 10V/m
EN61000-4-4 ±2kV
EN61000-4-5 ±1kV
EN61000-4-6 10Vrms
EN61000-4-8 30A/M
EN61000-4-11 30% 10ms
EN61000-4-11 >95% 5000ms
A
A
A
A
A
A
A
B
Notes
1
2
3
4
5
All specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted.
These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power
supplies however they may not meet all listed specifications.
We recommend to protect the converter by a slow blow fuse in the input supply line.
Other input and output voltage may be available, please contact factory.
Specifications are subject to change without notice.
Typical Constant Power V/I Curve
Output Voltage(VDC)
10
8
6
4
2
0
0
100
200
300
400
500
Output Current(mA)
E-mail:[email protected]
2016/06/02
REV:3
Tel:886-6-2923150
Page 2 of 3
600
700
800
900
ABW-02 SERIES
AC/DC POWER MODULE 2W
Package Specifications
Pin Connections
2x3.75
[2x0.15]
Mechanical Dimensions
Single Output
Dual Output
NC
4
3
+Vout
+Vout1
5
4
-Vout
Common
5
NP
+Vout2
Bottom View
0.80 [0.03]
NC
2
34.2 [1.35]
1
3
14.00 [0.55]
25.25 [0.99]
2
Pin
6
AC(N)
7
AC(L)
7.50
[0.30]
6
6.35
[0.25]
1
21.00 [0.83]
28.4 [1.12]
2.6 [0.10]
7
►All dimensions in mm
3.2 [0.13]
14.8 [0.58]
►Tolerance: ±0.5
►Pin
(inches)
(±0.01)
diameter  0.8 ±0.1 (0.03±0.004)
Physical Characteristics
Case Size
:
34.2x28.4x14.8mm (1.35x1.12x0.58 inches)
Case Material
:
Plastic resin (flammability to UL 94V-0 rated)
Pin Material
:
Copper Alloy with Gold Plate Over Nickel Subplate
Weight
:
24g
Minmax Technology Co., Ltd.
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected]
2016/06/02
REV:3
Page 3 of 3
Similar pages