AD AD53509JSW High performance driver/comparator active load on a single chip Datasheet

High Performance Driver/Comparator,
Active Load on a Single Chip
AD53509
FEATURES
250 MHz operation
Driver/comparator and active load included
On-chip Schottky diode bridge
52-lead LQFP_EP package
FUNCTIONAL BLOCK DIAGRAM
VCC
VCC VCC VCC
51
52
VEE
34
VEE VEE VEE
39
40
VH 47
41
32
39nF
CHDCPL
AD53509
VT 45
DATA 37
VHDCPL
DATA 38
APPLICATIONS
Automatic test equipment (ATE)
Semiconductor test systems
Board test systems
Instrumentation and characterization equipment
IOD 43
IOD 42
39nF
CLDCPL
46Ω
DRIVER
VOUT
VLDCPL
RLD 49
RLD 50
VL 31
HCOMP
LEH
LEH
The AD53509 is a single chip that performs the pin electronics
functions of driver, comparator, and active load in ATE VLSI
and memory testers. In addition, a Schottky diode bridge for
the active load and a VCOM buffer are included internally.
The driver is a proprietary design that features three active
states: data high mode, data low mode, and term mode as well
as an inhibit state. The output voltage range is −2 V to +7 V to
accommodate a wide variety of test devices. The output leakage
is typically <250 nA over the signal range.
The dual comparator, with an input range equal to the driver
output range, features built-in latches and ECL-compatible
outputs. The outputs are capable of driving 50 Ω signal lines
terminated to −2 V. Signal tracking capability is >5 V/ns.
The active load can be set up to 40 mA load current with less
than a 10 μA linearity error through the set range. IOH, IOL, and
the buffered VCOM are independently adjustable. On-board
Schottky diodes provide high speed switching and low
capacitance.
QH
QH
COMPARATOR
QL
QL
LEL
LEL
LCOMP
ACTIVE LOAD
VCOMI
VCOMS
+1
IOLC
V/I
IOLRTN
OUT_L
IOHRTN
INHL 36
THERM
INHL 35
1.0µA/K
IOHC
V/I
9
33 44 46 48
PWRGND
14 NC
26 NC
2
5
8
VCCO
HQGND2
NC = NO CONNECT
HQGND
01539-001
GENERAL DESCRIPTION
Figure 1.
Also included on the chip is an on-board temperature sensor
whose purpose is to give an indication of the surface temperature
of the DCL. This information can be used to measure θJC and θJA
or flag an alarm if proper cooling is lost. Output from the sensor
is a current sink that is proportional to absolute temperature.
The gain is trimmed to a nominal value of 1.0 μA/K. For example,
the output current can be sensed by using a 10 kΩ resistor
connected from 10 V to the THERM pin. A voltage drop across
the resistor then develops that equals
10 K × 1 μA/K = 10 mV/K = 2.98 V (at room temperature)
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
AD53509
TABLE OF CONTENTS
Features .............................................................................................. 1
Active Load Specifications ...........................................................6
Applications....................................................................................... 1
Total Function Specifications ......................................................7
General Description ......................................................................... 1
Absolute Maximum Ratings ............................................................8
Functional Block Diagram .............................................................. 1
ESD Caution...................................................................................8
Revision History ............................................................................... 2
Pin Configuration and Function Descriptions..............................9
Specifications..................................................................................... 3
Outline Dimensions ....................................................................... 11
Driver Specifications.................................................................... 3
Ordering Guide .......................................................................... 11
Comparator Specifications.......................................................... 5
REVISION HISTORY
3/08—Rev. A to Rev. B
Updated Format..................................................................Universal
Changes to Features and General Description ............................. 1
Changes to Table 1............................................................................ 3
Changes to Table 3............................................................................ 6
Changes to Table 9............................................................................ 8
Inserted Table 10............................................................................... 9
Updated Outline Dimensions ....................................................... 11
Changes to Ordering Guide .......................................................... 11
12/00—Rev. 0 to Rev. A
Rev. B | Page 2 of 12
AD53509
SPECIFICATIONS
DRIVER SPECIFICATIONS
All specifications are at TJ = 85°C ± 5°C, VCC = 11 V ± 3%, VEE = −6 V = ±3%, unless otherwise noted. All temperature coefficients are
measured at TJ = 75°C to 95°C.
Table 1.
Parameter
DIFFERENTIAL INPUT CHARACTERISTICS,
DATA to DATA, IOD to IOD, RLD to RLD
Input Voltage
Differential Input Range
Bias Current
REFERENCE INPUTS
Bias Currents
OUTPUT CHARACTERISTICS
Logic High Range
Logic Low Range
Amplitude, VH and VL
Absolute Accuracy
VH Offset
VH Gain + Linearity Error
VL Offset
VL Gain + Linearity Error
Offset Temperature Coefficient
Output Resistance
VH = −2 V
VH = +7 V
VL = −2 V
VL = +6 V
VH = +3 V
Dynamic Current Limit
Static Current Limit
Min
Typ
Max
Unit
Test Conditions
−250
+3
2
+250
V
V
μA
All digital inputs within a 2 V range
VIN = −2 V, +3 V
−50
+50
μA
VL, VH, VT = 5 V
−2
−2
0.1
+7
+6
9
V
V
V
−50
0.3 − 5
−50
−0.3 − 5
+50
0.3 + 5
+50
+0.3 + 5
mV
% of VH + mV
mV
% of VL + mV
mV/°C
Data = H, VH = −2 V to +7 V, VL = −2 V, VT = 0 V
Data = L, VL = −2 V to +6 V, VH = 7 V, VT = 0 V
VL = 0 V, VH = 0.1 V, VT = 0 V
VL = −2 V, VH = 7 V, VT = 0 V
Data = H, VH = 0 V, VL = −2 V, VT = −1 V
Data = H, VH = −1 V to +7 V, VL =−2 V, VT = −2 V
Data = L, VL = 0 V, VH = 5 V, VT = 3 V
Data = L, VL = −2 V to +6 V, VH = 7 V, VT = 7 V
VL = −2 V, VH = 0 V, VT = −1 V (VH offset),
VL = 0 V, VH = 5 V, VT = 3 V (VL offset)
48
48
48
48
Ω
Ω
Ω
Ω
Ω
mA
mA
VL = −2 V, VT = 0 V, IOUT = 0 mA, 1 mA, 30 mA
VL = −1 V, VT = 0 V, IOUT = 0 mA, −1 mA, −30 mA
VH = 6 V, VT = 0 V, IOUT = 0 mA, 1, mA 30 mA
VH = 7 V, VT = 0 V, IOUT = 0 mA, −1 mA, −30 mA
VL = 0 V, VT = 0 V, IOUT = −30 mA (trim point)
CBYP = 39 nF, VH = 6 V, VL = −2 V, VT = 0 V
Output to −2 V, VH = 7 V, VL = −1 V, VT = 0 V,
data = H and output to 7 V, VH = 6 V,
VL = −2 V, VT = 0 V, data = L
V
mV
% of VSET + mV
mV/°C
Ω
Term mode, VT = −2 V to +7 V, VL = 0 V, VH = 3 V
Term mode, VT = 0 V, VL = 0 V, VH = 3 V
Term mode, VT = −2 V to +7 V, VL = 0 V, VH = 3 V
VT = 0 V, VL = 0 V, VH = 3 V
IOUT = 30 mA, 1.0 mA, VT = −2.0 V, VH = 3 V,
VL = 0 V, IOUT = −30 mA, −1.0 mA, VT = 7.0 V,
VH = 3 V, VL = 0 V, IOUT = ±30 mA, ±1.0 mA,
VT = 0 V, VH = 3 V, VL = 0 V
1.5
ns
2
ps/°C
<100
ps
Measured at 50%, VH = 400 mV,
VL = −400 mV, VT = 0 V
Measured at 50%, VH = 400 mV,
VL = −400 mV, VT = 0 V
Measured at 50%, VH = 400 mV,
VL = −400 mV, VT = 0 V
−2
0.5
44
44
44
44
46
46
46
46
46
>100
−85
+85
−2
−50
−0.3 + 10
+7
+50
+0.3 + 10
VT
Voltage Range
VT Offset
VT Gain + Linearity Error
Offset Temperature Coefficient
Output Resistance
DYNAMIC PERFORMANCE, VH AND VL
Propagation Delay Time
Propagation Delay Temperature
Coefficient
Delay Matching, Edge to Edge
44
0.5
46
49
Rev. B | Page 3 of 12
AD53509
Parameter
Rise and Fall Times
1 V Swing
Unit
Test Conditions
0.42
ns
3 V Swing
0.75
ns
5 V Swing
1.65
ns
9 V Swing
3.0
ns
Measured 20% to 80%, VL = 0 V,
VH = 1 V, VT = 0 V
Measured 20% to 80%, VL = 0 V,
VH = 3 V, VT = 0 V
Measured 10% to 90%, VL = 0 V,
VH = 5 V, VT = 0 V
Measured 10% to 90%, VL = −2 V,
VH = 7 V, VT = 0 V
Rise/Fall Time Temperature Coefficient
1 V Swing
3 V Swing
5 V Swing
Overshoot and Preshoot
±1
±2
±4
<3 + 50
ps/°C
ps/°C
ps/°C
% of Step + mV
Measured 20% to 80%, VL = 0 V, VH = 1 V
Measured 20% to 80%, VL = 0 V, VH = 3 V
Measured 10% to 90%, VL = 0 V, VH = 5 V
VL, VH = −0.1 V, +0.1 V, VL, VH = 0 V, +1.0 V
VL, VH = 0 V, 3.0 V, VL, VH = 0 V, 5.0 V
VL, VH = −2.0 V, +7.0 V
Settling Time
to 15 mV
to 4 mV
Delay Change vs. Pulse Width
<50
<10
50
ns
μs
ps
VL = 0 V, VH = 0.5 V, VT = −2 V
VL = 0 V, VH = 0.5 V, VT = −2 V
VL = 0 V, VH = 2 V, pulse width = 2.5 ns/7.5 ns,
30 ns/90 ns
Minimum Pulse Width
3 V Swing
1.4
ns
2.0
ns
250
MHz
VL = 0 V, VH = 3 V, 90% (2.7 V) reached,
measure @ 50%
VL = 0 V, VH = 5 V, 90% (4.5 V) reached,
measure @ 50%
VL = 0 V, VH = 5 V, VDUT > 3.0 V p-p
3.3
2.9
<2
ns
ns
ns
Input/Output Spike
Rise/Fall Time, Active to Inhibit
150
1.6
mV p-p
ns
Rise/Fall Time, Inhibit to Active
1.4
ns
2.5
2.5
<3.0 + 75
ns
ns
% of Step + mV
Measured at 50%, VL = −1 V, VH = 1 V, VT = 0 V
Measured at 50%, VL = VH = 0.4 V, VT = −0.4 V
VH/VL, VT = (0 V, −1 V), (0 V, −2.0 V), (0 V, +6.0 V)
2.2
2.2
35
ns
ns
dB
VL = −2 V, VH = 2 V, VT = 0 V, 20% to 80%
VL = −2 V, VH = 2 V, VT = 0 V, 20% to 80%
VS = VS ± 3%
5 V Swing
Toggle Rate
DYNAMIC PERFORMANCE, INHIBIT
Delay Time, Active to Inhibit
Delay Time, Inhibit to Active
Delay Time Matching, Z
DYNAMIC PERFORMANCE, VT
Delay Time, VH to VT and VL to VT
Delay Time, VT to VH and VT to VL
Overshoot and Preshoot
VT Mode Rise Time
VT Mode Fall Time
PSRR, Drive, or Term Mode
Min
Typ
Max
Rev. B | Page 4 of 12
Measured at 50%, VH = 2 V, VL = −2 V, VT = 0 V
Measured at 50%, VH = 2 V, VL = −2 V, VT = 0 V
Z = delay time, active to inhibit − delay time,
inhibit to active (of worst two edges)
VH = 0 V, VL = 0 V, VT = 0 V
VH = 2 V, VL = −2 V (measured 20%/80% of
1 V output)
VH = 2 V, VL = −2 V (measured 20%/80% of
1 V output)
AD53509
COMPARATOR SPECIFICATIONS
All specifications are at TJ = 85°C ± 5°C. Outputs terminated in 150 Ω to GND, VCC = 11 V ± 3%, VEE = 6 V ± 3%, VCCO = 3.3 V,
unless otherwise specified. All temperatures coefficients are measured at TJ = 75°C to 95°C.
Table 2.
Parameter
DC INPUT CHARACTERISTICS
Offset Voltage, VOS
Offset Voltage, Drift
HCOMP, LCOMP Bias Current
Voltage Range, VCM
Differential Voltage, VDIFF
Gain and Linearity
LATCH ENABLE INPUTS
Logic 1 Current, IIH
Logic 0 Current, IIL
Logic Input Range
DIGITAL OUTPUTS
Logic 1 Voltage, VOH
Logic 0 Voltage, VOL
Slew Rate
VCCO Range
SWITCHING PERFORMANCE
Propagation Delay
Input to Output
Latch Enable to Output
Propagation Delay Temperature Coefficient
Propagation Delay Change with Respect to
Slew Rate: 0.5 V/ns, 1.0 V/ns, 3.0 V/ns
Slew Rate: 5.0 V/ns
Amplitude: 1.0 V, 3.0 V, 5.0 V
Equivalent Input Rise Time
Pulse Width Linearity
Settling Time
Latch Timing
Input Pulse Width
Setup Time
Hold Time
Hysteresis
Min
Typ
Max
Unit
Test Conditions
+25
mV
μV/°C
μA
V
V
% FSR
CMV = 0 V
CMV = 0 V
VIN = 0 V
μA
μA
V
LEA, LEA, LEB, LEB = 3 V
LEA, LEA, LEB, LEB = −2 V
V
V
V/ns
V
Qx or Qx, 16.7 mA load
Qx or Qx, 10 mA load
1.8
2
2
ns
ns
ps/°C
VIN = 2 V p-p
HCOMP = 1 V, LCOMP = 1 V
<±100
<±350
<±200
450
<±200
25
ps
ps
ps
ps
ps
ns
VIN = 0 V to 5 V
VIN = 0 V to 5 V
VIN = 1.0 V/ns
VIN = 0 V to 3 V, 3 V/ns
VIN = 0 V to 3 V, 3 V/ns, PW = 3 ns to 8 ns
Settling to ±8 mV, VIN = 1 V to 0 V
1.68
1.0
1.1
6
ns
ns
ns
mV
Latch inputs programmed for hysteresis
−25
50
−50
−2
+50
+7.0
9.0
+0.05
−0.05
250
−250
−2
+3
VCCO − 0.98
VCCO − 1.5
1
0
8
Rev. B | Page 5 of 12
VIN = −2 V to +7 V (9 V FSR)
AD53509
ACTIVE LOAD SPECIFICATIONS
All specifications are at TJ = 85°C ± 5°C, VCC = 11 V ± 3%, VEE = −6 V = ±3%, unless otherwise noted. All temperature coefficients are
measured at TJ = 75°C to 95°C.
Table 3.
Parameter
INPUT CHARACTERISTICS
INHL, INHL
Input Voltage
Bias Current
IOHC Current Program Range
IOH = 0 mA to −40 mA
IOLC Current Program Range
IOL = 0 mA to 40 mA
IOHC, IOLC Input Bias Current
IOLRTN, IOHRTN Range
VDUT Range
VDUT Range, IOH = 0 mA to −40 mA
VDUT Range, IOL = 0 mA to 40 mA
VCOMI Input Range
OUTPUT CHARACTERISTICS
Accuracy
Absolute Accuracy Error, Load Current
VCOM Buffer
Offset Error
Bias Current
Gain Error
Linearity Error
Output Current Temperature Coefficient
DYNAMIC PERFORMANCE
Propagation Delay
±IOUT to Inhibit
Inhibit to ±IOUT
Propagation Delay Matching
Input/Output Spike
Settling Time to 15 mV
Settling Time to 4 mV
Min
Max
Unit
Test Conditions
−2
−250
+3
+250
V
μA
IOHC = 1 V, IOLC = 1 V, VCOM = 2 V, OUT_L = 0 V
INHL, INHL = −2 V, +3 V
0
4
V
OUT_L = −0.7 V, +7 V
0
−300
−2
−2
−0.7
−2
−2
4
+300
+7
+7
+7
+5.7
+7
V
μA
V
V
V
V
V
OUT_L = −2 V, +5.7 V
IOLC = 0 V, 4.0 V and IOHC = 0 V, 4.0 V
IOL = 40 mA, IOH = −40 mA, OUT_L = −2 V, +7 V
IOL = 40 mA, IOH = −40 mA, OUT_L − VCOMI >1.3 V
OUT_L − VCOM > 1.3 V
VCOM − VDUT > 1.3 V
IOL = 40 mA, IOH = −40 mA
−0.3 − 100
+0.3 + 100
% ISET + μA
IOL, IOH = 25 μA to 40 mA, VCOM = 0 V,
OUT_L = ±2 V and IOL = 25 μA to 40 mA,
VCOM = 7 V, OUT_L = 5.7 V and IOH = 25 μA to
40 mA, VCOM = −2 V, OUT_L = −0.7 V
+50
+10
+0.2
mV
μA
%
+10
mV
IOL, IOH = 40 mA, VCOMI = 0 V, OUT_L = VCOM
VCOMI = 0 V, OUT_L = VCOM
IOL, IOH = 40 mA, VCOMI = −1 V to +6 V,
VOUT = VCOM
IOL, IOH = 40 mA, VCOMI = −1 V to +6 V,
VOUT = VCOM
Measured at IOH, IOL = 200 μA
−50
−10
−0.2
Typ
+1
−10
<±2
μA/°C
1.9
2.8
<1.8
240
<50
<10
ns
ns
ns
mV
ns
μs
Rev. B | Page 6 of 12
VCOM = ±2 V, IOL = 20 mA, IOH = −20 mA
VCOM = ±2 V, IOL = 20 mA, IOH = 20 mA
VCOM = 0 V, IOL = 20 mA, IOH = −20 mA
IOL = 20 mA, IOH = −20 mA, 50 Ω load to ±15 mV
IOL = 20 mA, IOH = −20 mA, 50 Ω load to ±4 mV
AD53509
TOTAL FUNCTION SPECIFICATIONS
All specifications are at TJ = 85°C ± 5°C, VCC = 11 V ± 3%, VEE = −6 V = ±3% unless otherwise noted. All temperature coefficients are
measured at TJ = 75°C to 95°C.
Table 4.
Parameter 1
OUTPUT CHARACTERISTICS
Output Leakage Current, VOUT = −1 V to +5 V
Output Leakage Current, VOUT = −2 V to +7 V
Output Capacitance
POWER SUPPLIES
Total Supply Range
Positive Supply, VCC
Negative Supply, VEE
Positive Supply Current
Negative Supply Current
VCCO Current
Total Power Dissipation
Temperature Sensor Gain Factor
1
Min
Typ
−250
−500
Max
Unit
Test Conditions
+250
+500
nA
μA
pF
Driver and load inhibited
V
V
V
mA
mA
mA
W
μA/K
Driver = INH, ILOAD program = 40 mA, load = active
Driver = INH, ILOAD program = 40 mA, load = active
VCCO = 3.3 V, comparator output 150 Ω to GND
Driver = INH, ILOAD program = 40 mA, load = active
RLOAD = 10 kΩ, VSOURCE = 11 V
8
17
11
−6
280
290
65
4.8
1
Connecting or shorting the decoupling pins to ground results in the destruction of the device.
Table 5. Driver Truth Table
DATA
DATA
0
1
X
X
IOD
IOD
1
1
0
0
1
0
X
X
RLD
RLD
X
X
0
1
0
0
1
1
Output State
VL
VH
Inhibit
VT
X
X
1
0
Table 6. Comparator Truth Table
>HCOMP
VOUT
>LCOMP
>HCOMP
<HCOMP
<HCOMP
X
<LCOMP
>LCOMP
<LCOMP
X
LEH
1
QH
0
LEL
1
Output States
QL
QH
0
1
0
1
0
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
QH (t − 1)
0
1
1
QH (t − 1)
0
1
0
QL (t − 1)
1
0
1
QL (t − 1)
LEH
LEL
QL
Table 7. Active Load Truth Table
INHL
OUT_L
<VCOM
INHL
0
1
IOH
V(IOHC) × 10 mA
>VCOM
X
0
1
1
0
V(IOHC) × 10 mA
0
Output States (Including Diode Bridge)
IOL
V(IOLC) × 10 mA
Rev. B | Page 7 of 12
V(IOLC) × 10 mA
0
I(OUT_L)
IOL
IOH
0
AD53509
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 8.
Parameter
Power Supply Voltage
VCC to GND
VEE to GND
VCC to VEE
VCCO to GND
PWRGND, HQGND, HQGND2
Inputs
DATA, DATA, IOD, IOD, RLD, RLD
DATA to DATA, IOD to IOD, RLD to RLD
LEL, LEL, LEH, LEH
LEL to LEL, LEH to LEH
INHL, INHL
INHL to INHL
VH, VL, VT, VCOMI to GND
VH to VL
(VH − VT) and (VT − VL)
IOHC
IOLC
HCOMP
LCOMP
HCOMP, LCOMP to VOUT
Outputs
VOUT Short-Circuit Duration
VOUT Inhibit Mode
VHDCPL
VLDCPL
QH, QH, QL, QL Maximum IOUT
Continuous
Surge
THERM
IOHRTN, IOLRTN
VCOMS Short-Circuit Duration
Environmental
Operating Temperature (Junction)
Storage Temperature Range
Lead Temperature (Soldering, 10 sec)2
Rating
13 V
−8 V
20 V
10 V
±0.4 V
Table 9. Package Thermal Resistance
−2 V to +5 V
±3 V
−2 V to +5 V
±3 V
−2 V to +5 V
±3 V
−3 V to +8 V
±10 V
±10 V
±6 V
±6 V
−3 V to +8 V
−3 V to +8 V
±10 V
Airflow (m/s)
0
1
2
θJA (°C/W)
42.7
37.8
36.4
For liquid-cooled applications, θJC = 3.0°C/W.
ESD CAUTION
Indefinite1
−3 V to +8 V
Do not connect except
for capacitor to VCC
Do not connect except
for capacitor to VEE
50 mA
100 mA
0 V to 13 V
−3.5 V to +8.5 V
3 sec1
175°C
−65°C to +150°C
260°C
1
Output short-circuit protection is guaranteed as long as proper heat sinking
is employed to ensure compliance with the operating temperature limits.
2
To ensure lead coplanarity (±0.002 inches) and solderability, handling with
bare hands should be avoided and the device should be stored in
environments at 24°C ± 5°C (75°F ± 10°F) with relative humidity not to
exceed 65%.
Rev. B | Page 8 of 12
AD53509
VEE
IOD
VEE
PWRGND
IOD
VT
VH
PWRGND
PWRGND
RLD
RLD
VCC
VCC
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
52 51 50 49 48 47 46 45 44 43 42 41 40
VCC 1
VCCO 2
QL 3
39 VEE
38 DATA
PIN 1
IDENTIFIER
37 DATA
36 INHL
QL 4
VCCO 5
QH 6
35 INHL
AD53509
34 VCC
33 PWRGND
HEAT SINK UP
(Not to Scale)
QH 7
VCCO 8
PWRGND 9
32 VEE
31 VL
LEL 10
LEL 11
30 IOLC
LEH 12
LEH 13
28 HQGND
29 IOHC
27 IOHRTN
NC = NO CONNECT
01539-002
IOLRTN
VCOMS
VCOMI
NC
VLDCPL
VOUT
OUT_L
VHDCPL
HQGND2
HCOMP
LCOMP
NC
THERM
14 15 16 17 18 19 20 21 22 23 24 25 26
Figure 2. Pin Configuration
Table 10. Pin Function Descriptions
Pin No.
1, 34, 51, 52
2, 5, 8
3
4
6
7
9, 33, 44, 46, 48
10
11
12
13
14, 26
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
Mnemonic
VCC
VCCO
QL
QL
QH
QH
PWRGND
LEL
LEL
LEH
LEH
NC
THERM
HCOMP
LCOMP
VHDCPL
HQGND2
VOUT
OUT_L
VLDCPL
IOLRTN
VCOMS
VCOMI
IOHRTN
HQGND
IOHC
IOLC
Description
Positive Power Supply.
Comparator Output Power Supply.
Comparator Low Output, Inverting.
Comparator Low Output, Noninverting.
Comparator High Output, Inverting.
Comparator High Output, Noninverting.
Ground.
Latch Enable Low Input, Inverting.
Latch Enable Low Input, Noninverting.
Latch Enable High Input, Inverting.
Latch Enable High Input, Noninverting.
Do not connect.
Temperature Sensor Output.
High Comparator Threshold.
Low Comparator Threshold.
Connect 39 nF compensation capacitor to VEE.
Ground.
DUT Connection.
Active Load Output.
Connect 39 nF compensation capacitor to VEE.
Active Load Low Inhibit Control.
VCOM Buffer Sense Output.
VCOM Input Voltage.
Active Load High Inhibit Control.
Ground.
Active Load High Current Control Input.
Active Load Low Current Control Input.
Rev. B | Page 9 of 12
AD53509
Pin No.
31
32, 39, 40, 41
35
36
37
38
42
43
45
47
49
50
Mnemonic
VL
VEE
INHL
INHL
DATA
DATA
IOD
IOD
VT
VH
RLD
RLD
Description
Low Driver Level.
Negative Power Supply.
Inhibit Load Input, Inverting.
Inhibit Load Input, Noninverting.
Drive Data Input, Noninverting.
Drive Data Input, Inverting.
IO Data Input, Inverting.
IO Data Input, Noninverting.
Term Driver Level.
High Driver Level.
VT/Inhibit Selection Input, Noninverting.
VT/Inhibit Selection Input, Inverting.
Rev. B | Page 10 of 12
AD53509
OUTLINE DIMENSIONS
0.75
0.60
0.45
16.20
16.00 SQ
15.80
1.60
MAX
40
52
1.00 REF
39
1
PIN 1
SEATING
PLANE
6.00
BSC SQ
EXPOSED
PAD
1.45
1.40
1.35
0.20
0.09
14.20
14.00 SQ
13.80
TOP VIEW
7°
3. 5°
0°
0.15
0.05
0.10
COPLANARITY
(PINS DOWN)
13
VIEW A
VIEW A
27
14
26
1.00
BSC
LEAD PITCH
0.50
0.42
0.35
COMPLIANT TO JEDEC STANDARDS MS-026-BEA-HU
022708-A
ROTATED 90° CCW
Figure 3. 52-Lead Low Profile Quad Flat Package, Exposed Pad [LQFP_EP]
(SW-52-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD53509JSW
AD53509JSWZ 1
1
Temperature Range
0°C to 70°C
0°C to 70°C
Package Description
52-Lead LQFP_EP
52-Lead LQFP_EP
Z = RoHS Compliant Part.
Rev. B | Page 11 of 12
Package Option
SW-52-1
SW-52-1
Ordering Quantity
90
90
AD53509
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D01539-0-3/08(B)
Rev. B | Page 12 of 12
Similar pages