Maxim MAX16125 Dual pushbutton controller Datasheet

19-6398; Rev 0; 7/12
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
General Description
The MAX16122–MAX16125 pushbutton controllers with
single-supply monitors monitor one or two pushbuttons and generate a hard reset signal if the buttons are
pushed and held for a setup delay. These devices make
it easy to “hide” the hard reset function in an existing
pushbutton, such as a soft power switch. The devices
operate from 1.6V to 5.5V and consume a quiescent current of only 5FA at 3V.
The MAX16122–MAX16125 have pin-programmable or
resistor-adjustable setup delay. Connect the SEL pin to
GND, VCC, or leave it unconnected to select the different
setup delays (depending on part suffix, see Table 1a) or
connect an external resistor from SEL to GND to set the
setup delays (E suffix only, see Table 1b).
The MAX16124/MAX16125 have one manual reset input
(MR), a reset output (RESET), and a soft reset output
(SRESET) which mirrors the state of the input. The
MAX16122/MAX16123 have two identical manual reset
inputs (MR1 and MR2) and one reset output (RESET). A
deglitch block is connected to each input to add a delay to
the falling edge with a fixed deglitch period of 20ms (tDB).
The MAX16122–MAX16125 feature a comparator that
monitors the input supply voltage. A variety of factorytrimmed threshold options accommodate different supply voltages and tolerances, eliminating external components. The factory-set reset thresholds range from 1.58V
to 4.63V to monitor 5V, 3.3V, 2.5V, and 1.8V supplies.
The MAX16122–MAX16125 are offered in a tiny 0.86mm
x 1.27mm, 6-bump WLP package and are specified over
the automotive temperature range (-40NC to +125NC).
Benefits and Features
S Low Supply Current: < 5µA (typ) at 3V Over
Temperature
S Precision Factory-Set VCC Monitoring Threshold
for 1.8V, 2.5V, 3.3V, and 5V Supplies
S Fixed/Pin-Programmable or Resistor-Adjustable
Pushbutton Setup Delay
S Up to 2 Reset Outputs and 2 Debounced
Pushbutton Inputs
S Guaranteed RESET Valid for VCC Down to 0.95V
S Active-Low RESET Output (Push-Pull or OpenDrain)
S Immune to Short Power-Supply Transients
S 0.86mm x 1.27mm 6-Bump WLP Package
S -40NC to +125NC Operating Temperature Range
Applications
Smartphones
Tablet PCs
eBook Readers
Portable/Battery-Powered Equipment
Glucose Monitors/Patient Monitors
Portable Instrumentation
Automotive Infotainment
Ordering Information appears at end of data sheet.
For related parts and recommended products to use with this part,
refer to www.maxim-ic.com/MAX16122.related.
Typical Operating Circuits
1.6V TO 5.5V
0.1µF
VCC
VCC
MAX16124
MAX16125
RESET
MR
RESET
INPUT
µP
SRESET
GND
I/0
GND
Typical Operating Circuits (continued) at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
ABSOLUTE MAXIMUM RATINGS
(All pins referenced to GND)
VCC...........................................................................-0.3V to +6V
RESET, SRESET to GND
Open-Drain...............................................................-0.3V to +6V
Push-Pull.................................................... -0.3V to (VCC + 0.3V)
MR, MR1, MR2.........................................................-0.3V to +6V
SEL...........................................................................-0.3V to +6V
Input/Output Current (all pins)............................................20mA
Continuous Power Dissipation (TA = +70NC) (Multilayer Board)
WLP (derate 10.5mW/NC above +70NC).......................840mW
Operating Temperature Range......................... -40NC to +125NC
Junction Temperature......................................................+150NC
Storage Temperature Range.............................-65NC to +150oC
Soldering Temperature (reflow).......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
WLP
Junction-to-Ambient Thermal Resistance (qJA)...........95°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(VCC = 1.6V to 5.5V, TA = -40NC to +125NC, unless otherwise noted. Typical values are at TA = +25NC.) (Note 2)
PARAMETER
Operating Voltage Range
VCC Undervoltage Lockout
SYMBOL
VCC
CONDITIONS
RESET state guaranteed for VCC R 0.95V
MIN
TYP
MAX
UNITS
5.5
V
1.25
1.55
V
1.6
VCCUVLO
VCC Supply Current
ICC
VCC = 5V, steady-state condition; MR, MR1,
MR2, RESET, and SRESET not asserted
8
10
FA
Supply Current with Oscillator
Running
ICC2
VCC = 3V
5
10
FA
VTH
VCC falling
VTH
+2.5%
VCC Reset Threshold
VCC Reset Threshold Hysteresis
-2.5%
VHYST
Reset Threshold Tempco
VCC to RESET Output Delay
tD
VCC falling at 10mV/Fs from (VTH + 100mV)
to (VTH - 100mV)
V
2
%
30
ppm/oC
10
Fs
Reset Timeout Period
tRP
See Table 2
-10
tRP
+10
%
Manual Reset Setup Delay
tSU
Internal timing (see Tables 1a, 1b, 1c)
-10
tSU
+10
%
Debounce Period
tDB
18
20
22
ms
2
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 1.6V to 5.5V, TA = -40NC to +125NC, unless otherwise noted. Typical values are at TA = +25NC.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
VCC = VTH(MIN), VTH > 4.25V,
ISINK = 10mA
0.4
V
VCC = VTH(MIN), VTH > 2.5V,
ISINK = 3.2mA
0.4
V
VCC = VTH(MIN), VTH > 1.67V,
ISINK = 1mA
0.4
V
VCC = VTH(MIN), VTH > 1V, ISINK = 100FA
0.4
V
0.4
V
OUTPUTS (RESET, SRESET)
RESET, SRESET Output Low
VOL
VCC > 0.95V, VCC falling, ISINK = 15FA
RESET, SRESET Output High
(Push-Pull Outputs)
VOH
VCC > 0.95V, ISOURCE = 15FA
0.8 x
VCC
V
VCC > 1.2V, ISOURCE = 100FA
0.8 x
VCC
V
VCC > 1.67V, ISOURCE = 150FA
0.8 x
VCC
V
VCC > 2.7V, ISOURCE = 500FA
0.8 x
VCC
V
VCC > 4.5V, ISOURCE = 800FA
0.8 x
VCC
V
RESET, SRESET Output Leakage
Current (Open-Drain Outputs)
1
FA
MANUAL RESET INPUTS (MR, MR1, MR2)
MR1, MR2, MR Input Voltage Low
VIL
MR1, MR2, MR Input Voltage High
VIH
Manual Reset Minimum Pulse
Width
0.3 x VCC
0.7 x VCC
MR1, MR2, MR Internal Pullup
Resistance
V
1
Manual Reset Glitch Rejection
Manual Reset to Soft Reset Delay
tMRD
25
V
Fs
100
ns
200
ns
50
80
kI
0.15 x
VCC
V
SELECT (SEL) LOGIC INPUT
SEL Input Low Voltage
SEL Input High Voltage
SEL Input Leakage
0.85 x
VCC
-8
V
+8
µA
Note 2: All parameters are production tested at TA = +25NC. Limits over the operating temperature range are guaranteed by
design.
3
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Typical Operating Characteristics
(VCC = 5V, MAX16125WTDB29+, TA = +25°C, unless otherwise noted.)
TA = +125°C
6
5
TA = +25°C
4
3
6
4
2
TA = -40°C
2
2.10
MAX16122 toc03
MAX16122 toc02
8
2.05
2.00
1.95
VCC = 3.3V
VCC = 3.0V
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
-40 -25 -10 5 20 35 50 65 80 95 110 125
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
VCC RESET THRESHOLD
vs. TEMPERATURE
12
10
8
6
4
2
5
4
VCC RESET THRESHOLD (%)
MAX16125WTDB29+
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
MAXIMUM VCC TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
14
1.90
MAX16125WTDB29+
3
MAX16122 toc05
1
MAX16122 toc04
7
10
SUPPLY CURRENT (µA)
TA = +85°C
8
MAXIMUM VCC TRANSIENT DURATION (µs)
SUPPLY CURRENT (µA)
9
MAX16122 toc01
10
RESET TIMEOUT PERIOD
vs. TEMPERATURE
SUPPLY CURRENT vs. TEMPERATURE
RESET TIMEOUT PERIOD (ms)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
2
1
0
-1
-2
-3
-4
NORMALIZED TO TA = +25°C
-5
0
0
0.05
0.10
0.15
0.20
RESET THRESHOLD OVERDRIVE (V)
0.25
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
4
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Typical Operating Characteristics (continued)
(VCC = 5V, MAX16125WTDB29+, TA = +25°C, unless otherwise noted.)
VCC TO RESET OUTPUT DELAY
vs. TEMPERATURE
MAX16122 toc08
MAX16122 toc07
8
PUSHBUTTON TIMING
0.40
MAX16122 toc06
0.35
0.30
RESET VOL (V)
6
4
MAX16125WTDB29+
MR1
2V/div
0.25
SRESET
2V/div
0.20
VCC = 1.5V
0.15
VCC = 2.5V
RESET
2V/div
0.10
2
tSU = 13.03µs
0.05
0
VCC = 2.9V
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
0
TEMPERATURE (°C)
2s/div
SINK CURRENT (mA)
tSU vs. RSEL
24
MAX16122 toc09
MAX16122 toc10
VCC TO RESET DELAY
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
22
20
18
VTH + 100mV
100mV/div
RESET
2V/div
4µs/div
SETUP DELAY (s)
VCC TO RESET OUTPUT DELAY (µs)
10
RESET OUTPUT-LOW VOLTAGE
vs. SINK CURRENT
16
14
12
10
8
6
4
2
0
10 60 110 160 210 260 310 360 410 460
SEL RESISTANCE TO GND (kI)
5
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Bump Configurations
TOP VIEW
BUMP SIDE DOWN
MAX16122/MAX16123
1
MAX16124/MAX16125
2
1
+
2
+
A
RESET
MR2
A
RESET
SRESET
B
SEL
MR1
B
SEL
MR
VCC
GND
C
VCC
GND
C
WLP
WLP
Bump Description
BUMP
MAX16122/
MAX16123
MAX16124/
MAX16125
NAME
FUNCTION
Active-Low Reset Output. RESET is either an open-drain or a push-pull output (see the
Selector Guide). RESET asserts low when VCC drops below the selected threshold and
remains low for the VCC reset timeout period after VCC rises above the reset threshold.
The RESET one-shot asserts low for the reset timeout period when the manual reset
input is asserted longer than the setup delay. The open-drain output requires an
external pullup resistor.
A1
A1
RESET
—
A2
SRESET
B1
B1
SEL
Setup Delay Select Input. Connect SEL to VCC, GND, or leave unconnected to select a
desired setup delay (see Table 1a); or connect an external resistor between SEL and
GND to select a desired setup delay (E suffix only, see Tables 1a and 1b).
—
B2
MR
Manual Reset Input. Internal 50kI pullup to VCC. Pull MR low for the setup delay (tSU)
to one-shot pulse RESET for the reset timeout period.
Soft Reset Output. SRESET is the debounced version of MR.
6
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Bump Description (continued)
BUMP
MAX16122/
MAX16123
MAX16124/
MAX16125
NAME
FUNCTION
C1
C1
VCC
Power-Supply Input. VCC provides power to the device and is also a monitored
voltage. When VCC drops below the selected threshold, RESET asserts low and
remains low for the reset timeout period after VCC rises above the threshold. Bypass
VCC to GND with a 0.1FF capacitor.
C2
C2
GND
Ground
B2
—
MR1
Active-Low Manual Reset Input 1. Internal 50kI pullup to VCC. Pull both MR1 and MR2
low for the setup delay (tSU) to one-shot pulse RESET for the reset timeout period.
A2
—
MR2
Active-Low Manual Reset Input 2. Internal 50kI pullup to VCC. Pull the MR2 and MR1
low for the setup delay (tSU) to one-shot pulse RESET for the reset timeout period.
Detailed Description
The MAX16122–MAX16125 low-current microprocessor
reset circuits feature single or dual manual reset inputs
with an extended setup period. The devices also feature
an internal comparator to monitor 5V, 3.3V, 2.5V, and
1.8V supplies.
When the monitored supply voltage drops below the
specified threshold, the active-low RESET output asserts
low and remains low for the reset timeout period (tRP).
The RESET output is one-shot pulse asserted for the
reset timeout period. Supply voltage reset threshold is
selectable through part suffix, see Table 3.
Connect SEL to GND, VCC, or leave unconnected to
select the different setup delays (depending on part suffix, see Table 1a), or connect to an external resistor to set
the setup delays (E suffix only, see Table 1b).
The MAX16124/MAX16125 have one manual reset input
(MR), one reset output (RESET), and one soft reset output
(SRESET). The MAX16122/MAX16123 have two identical
manual reset inputs (MR1 and MR2) and one reset output
(RESET). A deglitch block is connected to each manual
reset input to add a delay to the falling edge with a fixed
deglitch period of 20ms (tDB).
Resistor-Adjusted Setup Delay
For the MAX16122–MAX16125 with the E setup delay
suffix (MAX1612_WTE_+T), a resistor connected from
SEL to GND sets the setup delay. Table 1b shows common resistor values and the resulting setup delays. For
resistor values not in the table, use the following formula
to compute the setup delay:
t SU =
R
20
where R is the resistor value in kI and tSU is the resulting setup delay in seconds. For best results, use resistor
values between 10kI and 500kI.
Reset Output
The reset output is typically connected to the reset
input of a microprocessor (FP). A FP’s reset input starts
or restarts the FP in a known state. The MAX16122–
MAX16125 FP supervisory circuits provide the reset
logic to prevent code-execution errors during power-up,
power-down, and brownout conditions (see the Typical
Operating Circuits).
The MAX16122/MAX16123 have a reset output RESET.
The MAX16124/MAX16125 have a reset output RESET
and a soft-reset output SRESET which is the debounced
“mirror image” of MR (see Figure 1a).
7
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
All reset outputs are either active-low open-drain or
active-low push-pull (see the Selector Guide). RESET
changes from high to low whenever the monitored voltage VCC drops below the reset threshold voltage. Once
VCC exceeds its respective reset threshold voltage,
RESET remains low for the reset timeout period (tRP)
and then goes high. RESET is one-shot pulsed whenever
selected manual reset inputs are asserted longer than
the setup delay (tSU). RESET stays asserted for the normal reset timeout period.
RESET is guaranteed to be in the proper output logic
state for VCC R 0.95V. For applications requiring valid
reset logic when VCC is less than 0.95V, see the Ensuring
a Valid RESET Output Down to VCC = 0V (Push-Pull
RESET Output) section.
Manual Reset Input
Each device in the MAX16122–MAX16125 family includes
at least one manual reset input, which must be held logiclow for an extended setup period (t­SU) before the RESET
output asserts. An internal pullup resistor is connected to
each manual reset input. When valid manual reset input
conditions/setup periods are met, the RESET output is
pulsed low for the reset timeout period (see Table 2).
Existing front-panel pushbutton switches (i.e., poweron/-off, channel up/down, or mode select) can be used
to drive the manual reset inputs. The extended manual
reset setup period prevents nuisance system resets during normal front-panel usage or resulting from inadvertent short-term pushbutton closure.
The MAX16124/MAX16125 include a single manual reset
input (MR) and two reset outputs (RESET and SRESET).
The MAX16122/MAX16123 include two manual reset
inputs (MR1 and MR2) and one reset output, RESET.
For dual MR1 and MR2 devices, both inputs must be
simultaneously pulled low and held for the extended
setup period (tSU) before the reset output is pulsed. The
dual extended setup provides greater protection from
nuisance resets.
The MAX16122–MAX16125 RESET output is asserted
once for the reset timeout period after each valid manual
reset input condition. At least one manual reset input
must be released (go high) and then be driven low for
the extended setup period before RESET asserts again.
Internal timing circuitry debounces low-to-high manual
reset logic transitions, so no external circuitry is required.
tDB
tSU
MR
(MR1 AND MR2)
GND
tRP
RESET
GND
ONE-SHOT PULSE ON RESET
*SRESET
GND
tMRD
*SRESET IS FOR MAX16124/MAX16125
( ) MR1 AND MR2 IS FOR MAX16122/MAX16123
Figure 1a. Reset Timing Diagram
8
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
VCC
VTH
MR
tSU
tRP
tDB
RESET
SRESET
MAX16124/MAX16125; NO RESET TIMEOUT PERIOD AT STARTUP
VCC
VTH
MR
tSU
tRP
RESET
tRP
tDB
SRESET
MAX16124/MAX16125; RESET TIMEOUT PERIOD AT STARTUP
Figure 1b. Timeout Periods at Startup
9
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Supply Voltage Monitor
The MAX16122–MAX16125 have an internal comparator
with a programmable trip threshold to monitor the supply voltage. The VCC monitoring thresholds are selectable through the part number suffix (see the Ordering
Information and Table 3).
Applications Information
Falling VCC Transients
In addition to issuing a reset to the FP during power-up,
power-down, and brownout conditions, the MAX16122–
MAX16125 are relatively immune to short-duration falling VCC transients (glitches). The Typical Operating
Characteristics show the Maximum Transient Duration
vs. VCC Overdrive graph for which the MAX16122–
MAX16125 do not generate a reset pulse. This graph was
generated using a falling pulse applied to VCC starting
above the actual reset threshold and ending below the
threshold by the magnitude indicated (VCC overdrive).
The graph indicates the typical maximum pulse width
that a falling transient can have without initiating a reset
pulse. As the magnitude of the transient increases (go
farther below the reset threshold), the maximum allowable pulse width decreases.
Ensuring a Valid RESET Output Down to
VCC = 0V (Push-Pull RESET Output)
The MAX16122–MAX16125 guarantee proper operation
down to VCC = 0.95V. In applications that require valid
reset levels down to VCC = 0V, add a pulldown resistor between RESET and GND for the push-pull outputs
(MAX16122/MAX16124). The resistor sinks any stray
leakage currents, holding RESET low (Figure 2). The
resistor value used is not critical, but it must be small
enough not to overload the RESET output when VCC is
above the reset threshold. For most applications, use
100kI to 1MI. This scheme does not work with opendrain outputs of the MAX16123/MAX16125.
Layout and Bypassing
Ensure 0.1FF (minimum) capacitance is connected from
VCC to GND.
VCC
MAX16122
MAX16124
VCC
RESET
GND
100kI
Figure 2. Ensuring RESET Output to VCC = 0V
10
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Typical Operating Circuits (continued)
I/0
VCC
I/0
I/0
I/0
PWR
VOL
UP
VOL
DN
HOME
1.6V TO 5.5V
µP
0.1µF
VCC
MR1
MAX16122
MAX16123
MR2
RESET
RESET
INPUT
SEL
GND
RSEL
11
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Functional Diagrams
MAX16124/MAX16125
VCC
RESET TIMEOUT
PERIOD
RESET
VCC
1.23V
SEL
VCC
MR
SETUP DELAY
SELECTOR
MANUAL
RESET SETUP
DELAY
(tSU)
DEGLITCH
SRESET
GND
12
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Functional Diagrams (continued)
VCC
MAX16122/MAX16123
RESET TIMEOUT
PERIOD
RESET
VCC
1.23V
SEL
VCC
MR1
SETUP DELAY
SELECTOR
MANUAL
RESET SETUP
DELAY
(tSU)
DEGLITCH
VCC
DEGLITCH
MR2
GND
13
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Table 1a. SEL Pin Connection Setup
Delays (tSU)
Table 2. Reset Timeouts (tRP)
PART SUFFIX
MINIMUM RESET TIMEOUT (ms)
SETUP DELAYS (s)
A
0.9
SEL =
UNCONNECTED
SEL = VCC
B
1.8
C
3.6
PART
SUFFIX
SEL = GND
A
0.5
1
2
D
7.2
B
3
4
5
E
14.4
C
6
8
10
F
28.8
17
G
57.6
H
86.4
D
13
E
15
See Table 1b
Table 1b. Resistor-Adjusted Setup Delays
(tSU)
RESISTOR (kI)
SETUP DELAYS (s)
10
0.5
18
0.9
22
1.1
27
1.35
39
1.95
47
2.35
56
2.8
82
4.1
100
5
180
9
220
11
I
115.2
J
172.8
K
230.4
L
259.2
M
345.6
N
460.8
O
691.2
P
921.6
Q
1843.2
R
3686.4
S
7372.8
Table 3. VCC Reset Threshold Voltage (VTH)
SUFFIX
VCC RESET THRESHOLD
VOLTAGE (V) (typ)
00
No Monitoring
16
1.58
17
1.67
22
2.19
23
2.32
29
2.93
31
3.08
44
4.38
46
4.63
14
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX16122WT_ _ _ _+T*
-40NC to +125NC
6 WLP
MAX16123WT_ _ _ _+T*
-40NC to +125NC
6 WLP
MAX16124WT_ _ _ _+T*
-40NC to +125NC
6 WLP
MAX16125WT_ _ _ _+T
-40NC to +125NC
6 WLP
Note: Insert the desired setup delay (A to Q, from Table 1a) into the blank following the letters WT. Insert the letter corresponding
to the desired minimum reset timeout period (A to S, from Table 2) into the blank following the setup delay suffix. Insert the two digit
number corresponding to the desired nominal reset threshold (from Table 3) into the blanks following the reset timeout suffix.
+Denotes a lead(Pb)-free/RoHS-compliant package. Devices are available only in lead-free packaging.
T = Tape and reel.
*Future product—Contact factory for availability.
Selector Guide
PART
DUAL MANUAL
RESET INPUT
SRESET
SEL
ACTIVE-LOW
RESET OUTPUT
MAX16122WT_ _ _ _+T
√
—
√
Push-pull
Open-drain
MAX16123WT_ _ _ _+T
√
—
√
MAX16124WT_ _ _ _+T
—
√
√
Push-Pull
MAX16125WT_ _ _ _+T
—
√
√
Open-drain
Note: MAX16125WTDB29+T is a standard option. For additional options, please contact factory.
Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
WLP
W61F0+1
21-0217
Refer to
Application
Note 1891
15
MAX16122–MAX16125
Dual Pushbutton Controllers in
Tiny 6-Bump WLP Package
Revision History
REVISION
NUMBER
REVISION
DATE
0
7/12
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
©
2012 Maxim Integrated Products
16
Maxim is a registered trademark of Maxim Integrated Products, Inc.
Similar pages