ON ENA2221 4:1 micro usb switch Datasheet

Ordering number : ENA2221
LC824204-13YB
4:1 Micro USB Switch
with Accessory detection and OVP
http://onsemi.com
Overview
The LC824204-13YB is the IC suitable for use in multi function and high performance switch as well as compatible
accessory detector which supports micro USB connector for DSC, DVC and mobile phone.
This IC includes low impedance USB supply switch (100 mΩ) which enables high speed battery charge as well as
USB2.0-capable switch with low input capacitance, negative input-capable low distortion audio switch, UART,
microphone (Mono, Stereo), and various video signal switches.
Also, this IC integrates auto detector for accessories which is capable of detecting accessories compliant to CEA936-A
automotive kit and ACA standard which includes MCPC standard established in June 2010. In addition, it’s capable of
detecting a lot of charger accessories, such as Dedicated (D+/D- short) charger, Apple charger, SONY charger, USB
charger and so on. Switching operation is controlled via I2C serial interface.
Function
WLP25(2.07X2.07)
Battery
Baseband
LDO
OVP
UVLO
OCP
VBUS
I 2C
USB-PHY
Audio
Codec
I2C
CTL
(LOAD FET)
Battery
Charger IC
VBUS-SW
LC824204-13YB
■ Configuration
• Audio-SW (Mono/Stereo, Negative signal capable)
• USB2.0-SW (LowSpeed/FullSpeed/HighSpeed-capable)
• UART-SW
• Video-SW (Video + V_Audio-R/L)
• MIC-SW (DP/VBUS switch, Mono/Stereo-capable)
• VBUS-SW
- High speed battery charge –capable (100mΩ)
- Integrated OVP, OCP, TSD
- DP/DM short-circuit detection, VBUS auto detection
- Various charger detection (Dedicated, Apple, SONY, USB)
• ID detection function
- Integrated 5-bit ADC
- I2C Interrupt function
■ Package
• WLCSP Pin25, 2.07 mm  2.07 mm, 0.4 mm pitch
• Halogen-free, lead-free-capable
■ Operating temperature
• 30 to 85C
■ Supply voltage
• VDD : 3.0 to 3.6 V
• VBUS : 4.5 to 5.5 V
■ ID detection for the accessories
• MCPC standard, CEA936-A automotive kit standard,
ACA standard-compliant
■ Application
• DSC, DVC, mobile phone
Charger
Detect
Switch
Array
ID
Detect
ID
D+
D-
Application Diagram
ORDERING INFORMATION
See detailed ordering and shipping information on page 14 of this data sheet.
Semiconductor Components Industries, LLC, 2013
October, 2013 Ver. 1.0
O2313HK 20130621-S00001 No.A2221-1/14
LC824204-13YB
Block Diagram
LC824204-13YB
Test
Circuit
VBUS
VBUSOUT
VDD
Over Current Protect
Gate control
Charge Pump
VBUS Detector
CHG_DETB
B/ B
I2C_SCL
I2C_SDA
INTB
ID Detector
(5bit ADC)
I2C
Serial
controller
OVP
UVLO
Vref
ID
Charge
Detector
RESETB
PHY
TSD
VBUS- SW
(LOAD FET)
Switch Selector
Pullup- Down Reg cont.
DP_HOST
DP
HPR
VDD
Audio codec
MIC_R
(V_HPR)
VDD
RXD
Micro-USB connector
POWER
TEST
DM_HOST
DM
HPL
VDD
MIC_L
(V_HPL)
VDD
UART
VDD
TXD
VDD
MIC
Video
VIDEO
GND
No.A2221-2/14
LC824204-13YB
Pin Assignment
Top Through View
A
VDD
VBUSOUT
VBUSOUT
VBUS
VBUS
B I2C_SDA
MIC_L
(V_HPL)
HPL
DM_HOST
DM
C
I2C_SCL
MIC_R
(V_HPR)
HPR
DP_HOST
DP
D
INTB
CHG
_DETB
MIC
VIDEO
ID
E
RXD
TXD
TEST
RESETB
GND
1
2
3
4
5
Pin Description
Ball No.
Name
Direction
1A
VDD
P
Power Supply for SW-IC
Description
4A,5A
VBUS
P/I
Power Supply for USB and Battery, MIC input
5E
GND
P
Ground
2A,3A
VBUSOUT
O
Output from VBUS
5D
ID
I/O
ID input, Video output
2D
CHG_DETB
O
Charger Detection output*
5C
DP
I/O
USB bath/Audio output, MIC/MIC_R input, UART output*
5B
DM
I/O
USB bath/Audio output, MIC_L input, UART input
4B
DM_HOST
I/O
USB differential data I/O minus
4C
DP_HOST
I/O
USB differential data I/O plus
3C
HPR
I
Audio Right input (Video Audio Right input)
3B
HPL
I
Audio Left input (Video Audio Left input)
1E
RXD
O
UART receive data output*
2E
TXD
I
UART transmission data input
3D
MIC
O
MIC output
4D
VIDEO
I
Video input
2C
MIC_R
(V_HPR)
I/O
Stereo MIC R output (Video Audio Right input )
2B
MIC_L
(V_HPL)
I/O
Stereo MIC L output (Video Audio Left input )
1C
I2C_SCL
I
I2C Serial Clock signal
1B
I2C_SDA
I/O
I2C Serial Data signal*
1D
INTB
O
Interrupt signal*
4E
RESETB
I
Hard Reset input (Low active)
3E
TEST
I
Test pin
Notice) If Video function is not needed, please use the port of Video as NC pins.
No.A2221-3/14
LC824204-13YB
Absolute Maximum Ratings at Ta = 25C
Parameter
Maximum supply voltage
Unit
VDD
0.3 to 4.6
V
VBUS
0.3 to 28.0
V
USB_Path
0.5 to 4.6
V
UART_Path
0.3 to 4.6
V
AUDIO_Path
1.5 to 4.6
V
AUDIO Input Range
3.0
Vpp
MIC(DP)_Path
0.5 to 4.6
V
MIC(DP) Input Range
2.0
Vpp
VBUS
↔ MIC Pin
MIC(VBUS)_Path
0.3 to 4.6
V
MIC(VBUS) Input Range
2.0
Vpp
DP/DM pin
↔ Signal pin
Stereo-MIC_Path
Stereo-MIC Input Range
0.5 to 4.6
2.0
Vpp
DP/DM pin
↔ Signal pin
Maximum
input
/output
voltage
Ratings
VIDEO pin
↔ ID pin
Maximum input/output
voltage
Allowable loss 2)
Operating temperature
range
V
VIDEO_Path
1.5 to 4.6
V
VIDEO Input Range
3.0
Vpp
VBUSOUT (Output Only)
0.3 to 6.0
V
Others1)
Pd (Ta = 25C)
0.3 to 4.6
690
V
mW
Topr
30 to +85
C
Tstg
55 to +125
C
Storage temperature range
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
*1) The Others means I2C_SCL, I2C_SDA, INTB, RESETB, CHG_DETB, and TEST pin.
*2) The values were obtained with glass epoxy board of 50 x 40 x 0.9t mm.
Recommended Operating Conditions at Ta = 25C
Parameter
Symbol
Min
Max
Unit
VDD voltage
VDD
3.0
3.6
V
VBUS voltage
VBUS
4.5
5.5
V
AUDIO input range
VSW_AUDIO
1.4
1.4
V
MIC(DP) input range
VSW_MICDP
0
2.5
V
MIC(VBUS) input range
VSW_MICVBUS
0
2.5
V
Stereo-MIC input range
VSW_SMIC
0
2.5
V
VIDEO input range
VSW_VIDEO
1.4
1.4
V
USB input range
VUSBin
0
3.6
V
Other signal input *
Vin
0
VDD
V
Allowed capacitance of load of
accessory ID pin
IDcap
300
pF
Condition
bias < 2.0 V,
1.0 Vpp
bias < 2.0 V,
1.0 Vpp
bias < 2.0 V,
1.0 Vpp
1.0 Vpp
* Other signal input signifies I2C_SCL, I2C_SDA, RESETB, TEST, TXD and RX (DP) pin.
No.A2221-4/14
LC824204-13YB
Electrical Characteristics at Ta  25C
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
IDDS2
VBUS = open,
RESETB = 0 V → VDD,
I2C_SCL = I2C_SDA = VDD,
TEST = 0 V, Others_pin = open
-
50
60
μA
IDD1
AUDIO-mode (288k)
VBUS = open, RESETB = VDD,
I2C_SCL = I2C_SDA = VDD,
TEST = 0 V, Others_pin = open
-
80
100
μA
IDD2
USB-mode(open)
VBUS = 5.0 V, RESETB = VDD,
I2C_SCL = I2C_SDA = VDD,
TEST = 0 V, Others_pin = open
-
80
100
μA
1.4
-
1.4
V
-
6.5
12
Ω
■VDD Current Consumption
Sleep Mode Current
Active Mode Current
(Audio + VBUS MIC-mode)
Active Mode Current
(USB mode)
■AUDIO-SW
Signal Range
VIN_LR
AUDIO_SW ON Resistance
RLR
Pull Down Resistance
RHPLR
30
50
70
kΩ
VIN_USB
0
-
3.6
V
3.2
5
Ω
HPR/HPL = -10 mA,
DP/DM = -1.3 V,
Calculated by R = V / 0.01
■USB-SW
Signal Range
RONUSB
DP/DM = 0 V,
DP_HOST/DM_HOST
SINK = 10 mA,
Calculated by R = V / 0.01
Signal Range
VIN_MIC1
Vbias < 2.0 V,
VSW_MICDP = 1.0 Vpp
0
-
2.5
V
MIC_SW ON Resistance
RMIC1
DP = 0.1 V, MIC = -10 mA,
Calculated by R = V / 0.01
-
7.5
15
Ω
Pull Down Resistance
RPUMIC1
1.2
2.2
3.2
kΩ
USB_SW ON Resistance
■MIC-SW (DP Input)
■MIC-SW (VBUS Input)
Signal Range
VIN_MIC2
Vbias < 2.0 V,
VSW_MICB = 1.0 Vpp
0
-
2.5
V
MIC_SW ON Resistance
RMIC2
VBUS = 0.1 V, MIC = -10 mA,
Calculated by R = V / 0.01
-
7.5
15
Ω
Pull Down Resistance
RPUMIC2
1.2
2.2
3.2
kΩ
■StereoMIC-SW (include DP_MIC)
Signal Range
VIN_MIC3
Vbias < 2.0 V,
VSW_SMIC = 1.0 Vpp
0
-
2.5
V
MIC_SW ON Resistance
RMIC3
DP/DM = 0.1 V,
MIC_R/MIC_L = -10 mA,
Calculated by R = V / 0.01
-
7.5
15
Ω
Pull Down Resistance
RPUMIC3
1.2
2.2
3.2
kΩ
■VIDEO-SW
Signal Range
VIN_V
VSW_VIDEO = 1.0 Vpp
1.4
-
1.4
V
VIDEO_SW ON Resistance
RV
Video = -1.4 V, ID = -10 mA,
Calculated by R = V / 0.01
-
4
8
Ω
No.A2221-5/14
LC824204-13YB
Electrical Characteristics at Ta  25C
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Low Level Output Voltage
VOL_TX
SINK = 1 mA
-
-
0.4
V
Pull Up Resistance
RTX
5
10
15
kΩ
High Level Input Voltage
VIHTXD
1.5
-
-
V
Low Level Input Voltage
VILTXD
-
-
0.7
V
Pull Up Resistance
RTXD
5
10
15
kΩ
High Level Input Voltage
VIHRX
1.5
-
-
V
Low Level Input Voltage
VILRX
-
-
0.7
V
Pull Up Resistance
RRX
5
10
15
kΩ
■UART-SW
TX (DM)
TXD
RX (DP)
RXD
Low Level Output Voltage
VOL_RXD
SINK = 1 mA
-
-
0.4
V
RVBUS
VBUS = 5.0 V,
VBUSOUT = -300 mA,
Calculated by R = V / 0.3
-
100
250
mΩ
VDD = 3.3 V, VBUS = upper
3.8
4.0
4.2
V
VDD = 3.3 V, VBUS = lower
3.0
3.2
3.4
V
VOVP
VDD = 3.3 V,
VBUS = upper & lower
5.8
6.0
6.4
V
ICL2
VBUS_ILIMIT = Mid
420
-
(700)
mA
ICL3
VBUS_ILIMIT = High
650
-
(1050)
mA
ICL4
VBUS_ILIMIT = Super
1500
-
-
mA
■VBUS-SW
VBUS_SW ON Resistance
UVL Cancel Voltage
UVL Detect Voltage
VVBUSH
_DET
VVBUSL
_DET
OVP Threshold Voltage
Charging Current
■ I2C_SCL, I2C_SDA
High Level Input Voltage
VIH_I2C
1.5
-
VDD+0.5
V
Low Level Input Voltage
VIL_I2C
0.3
-
0.3
V
Hysteresis of inputs
VHYS_I2C
0.05*VDD
-
-
V
High Level Input Voltage
VIH_IO
1.5
-
-
V
Low Level Input Voltage
VIL_IO
-
-
0.3
V
-
-
0.4
V
■ RESETB, TEST
■ I2C_SDA, INTB, CHG_DETB
Low Level Output Voltage
VOL_I2C
SINK = 3 mA
No.A2221-6/14
LC824204-13YB
Function Description
Charger Detection
By using charger detector circuit including built-in D+/D- short-circuit detector, you can judge the connection of DP pin
and DM pin and then detect charger according to USB Charger and Battery Charging Specification Revision 1.1 as well as
CEA936-A automotive kit specification. This IC can detect the charger of the following list.
Detectable charger list
Standard Downstream Port (USB mode)
Dedicated Charging Port (D+/D- short ACC)
Apple Charger
SONY Charger
D- High Charger (Basic CarKit Type1,2 ACC)
VBUS only ACC (No Charger Detect)
Accessory ID Detection
Accessory is detected according to CEA936-A automotive kit and ACA standard including MCPC standard using ID
detection circuit including built-in 5-bit ADC. Accessories are judged from the resistance value of accessory (RID)
connected to ID pin. ID range of RID varies depends on each standard. See Resistance (RID) and Detectable accessory for
the further details.
Resistance (RID) and Detectable Accessory
RID
Detectable Accessory
Comments
Open
No Accessory
Open
AC Adapter (Fast Charger)
(D+/D- : Shorted)
Open(over 1M )
USB-Mode
(D+/D- : Not shorted)
750k + 47k
(759k to 835k)
Audio with MIC (Mono)
510k + 47k
(531k-583k)
Audio (Mono Earphone)
+ Charger (Std Charger) + MIC (D+ in)
(D+/D- : Not shorted)
Fast Charger (Typ2 Charger)
Charger 5Wire/Type2
(D+/D- : Shorted)
Carkit (Type2)
BasicCarkit 5Wire/type2
also used for Muting (D- : High)
440k
(436k-444k)
390k
Video-Audio
(379k-408k)
Video-Audio with VBUS
(D+/D- : Not shorted)
Audio with MIC (Stereo)
240k + 47k
(275k-294k)
Audio with VBUS (Stereo)
MIC-SW turns off
when VBUS Detection.
(D+/D- : Not shorted)
No.A2221-7/14
LC824204-13YB
Table of Resistance (RID) and Detectable Accessory
RID
200k
(198k-202k)
Detectable Accessory
Comments
Std Charger (Typ1Charger)
Charger 5Wire/Type1
(D+/D- : Shorted)
Carkit (Type1)
BasicCarkit 5Wire/type1
also used for Muting (D- : High)
150k-180k
UART
119k-124k-132k
RID_A
100k-102k
(96k-106k)
Audio (Stereo)
65k-68k-72k
RID_B
35k-36.5k-39k
RID_C
20k
Custom Accessory
14k
Stereo-MIC with VBUS
11k
Stereo-MIC
7k
Custom Accessory with VBUS
4k
Custom Accessory
3.1k
Custom Accessory with VBUS
2.5k
Custom Accessory
1.7k
Custom Accessory with VBUS
ACA A-device (RID_A)
Vbus come fm Charger
Headset / Stereo
Phone Powered Accessory
(D+/D- : Not shorted)
ACA B-device,
no connect (RID_B)
Vbus come fm Charger can SRP
ACA B-device,
no connect (RID_C)
Vbus come fm Charger no SRP
D+/D- : Not shorted
D+/D- : Not shorted
D+/D- : Not shorted
D+/D- : Not shorted
Video
75
0-10
Video with VBUS
D+/D- : Not shorted
USB-OTG Host
No.A2221-8/14
LC824204-13YB
Table of Resistance (RID) and Selecting switch.
SW Selection
RID
Detectable Accessory
VBUS
USB
AUDIO
_R
AUDIO
_L
UART
MIC_
VBUS
MIC_
D+
VIDEO
Stereo
-MIC
No Accessory
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
AC Adapter (Fast Charger)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
USB-Mode
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
750k + 47k
Audio (with MIC) (Mono)
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
510k + 47k
Audio (Mono Earphone)
+Charger (Std Charger)
+MIC (D+ in)
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
Fast Charger (Typ2Charger)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Carkit (Type2)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Video-Audio
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
Video-Audio with VBUS
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
Audio with MIC (Stereo)
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
Audio with VBUS (Stereo)
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
Std Charger (Typ1Chager)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Carkit (Type1)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
150k-180k
UART
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
119k-124k132k
RID_A
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Audio (Stereo)
:Headset / Stereo
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
Audio (Stereo)
*1)
Phone Powered Accessory
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
65k-68k-72k
RID_B
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
35k-36.5k39k
RID_C
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
-
-
-
-
-
-
-
-
-
Open
440k
390k
240k + 47k
200k
100k-102k
20k
*2)
Custom Accessory
14k
Custom Accessory
*2)
with VBUS
-
-
-
-
-
-
-
-
-
11k
Stereo-MIC
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
7k
Custom Accessory
*2)
with VBUS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Custom Accessory
*2)
with VBUS
-
-
-
-
-
-
-
-
-
VIDEO
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
VIDEO with VBUS
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
4k
3.1k
2.5k
1.7k
75
0-10
*2)
Custom Accessory
Custom Accessory
*2)
with VBUS
*2)
Custom Accessory
USB-OTG Host
*1)
Note *1) You can only detect RID (you cannot select SW).
Note *2) Custom Accessory : User can define SW selection.
No.A2221-9/14
SDA
SCL
Reading
SDA
SCL
Writing
1
1
MSB
Start
0
0 0
0
0
ACK
A7 A6 A5 A4 A3 A2 A1 A0
Write ACK
0
Register Address
Start
(NO2)
1
0
0 1
0
0
Stop
Register Data (Read)
Stop
NO_ACK
D7 D6 D5 D4 D3 D2 D1 D0
Read ACK
0
ACK
Slave Address
I2C Transfer Sequence and Timing when reading command orders
0 1
Slave Address
0
Register Data (Write)
D7 D6 D5 D4 D3 D2 D1 D0
ACK
A7 A6 A5 A4 A3 A2 A1 A0
Write ACK
0
Register Address
I2C Transfer Sequence and Timing when writing command orders
0 1
Slave Address
I2C Reading
Command Order
MSB
Start
I2C Writing
Command Order
LC824204-13YB
I2Cbus timing (serial I/F)
No.A2221-10/14
LC824204-13YB
2
*I Cbus timing
tF
tHIGH
tLOW
tR
tSP
SCL
tSU.STA
tSU.DAT
tHD.STA tHD.DAT
tSU.STO
tSP
SDA
tBUF
Symbol
Parameter
Min
Max
Unit
tSCL
tBUF
tHD:STA
tLOW
tHIGH
tR
tF
tSU:STA
tSU:STO
tSU:DAT
tHD:DAT
SCL clock fr.
Bus release period
Hold time (Start)
SCL_Lo period
SCL_Hi period
Rise time
Fall time
Setup time (Start)
Setup time (Stop)
Setup time (Data)
Hold time (Data)
Removable spike
width
0
1.3
0.6
1.3
0.6
400
kHz
μs
μs
μs
μs
ns
ns
μs
μs
ns
ns
tSP
300
300
0.6
0.6
100
0
50
ns
I2C system reset
tRSTL
RESETB
*2)
VDD
Symbol
tRSTL * 1)
Parameter
resetLow time
Min
5
Max
Unit
μs
* 1) RESETB is the reset signal of the group of register by I2C. Therefore, you need Low
period for tRSTL after powering VDD.
No.A2221-11/14
LC824204-13YB
I/O Equivalent Circuit
PortName
Cuircuit
PortName
Cuircuit
VDD
VBUS
VBUSOUT
HPL
HPR
VDD
1.5uA
(Normal)
ID
Ext.
Accessory
MIC_L
(V_HPL)
MIC_R
(V_HPR)
MIC
VIDEO
VDD
(VIDEO)
DP
DM
DP_HOST
DM_HOST
RXD
VDD
TXD
INTB
I2C_SCL
I2C_SDA
VDD
CHG_DETB
RESETB
VDD
TEST
No.A2221-12/14
LC824204-13YB
Application Circuit Example
VDDIO
1kΩ~ 1kΩ~
10kΩ 10kΩ
LC824204-13YB
1kΩ~
10kΩ
Battery
Charger-IC
VBUSOUT
1uF
I2C_SCL
VDD
I2C_SDA
B/B
0.1uF
INTB
RESETB
USBPHY
LDO
Battery
+
-
1uF
Voltage
Supervisor
DP_HOST
DM_HOST
CHG_DETB
TEST
HPR
HPL
Audio&
Video
codec
V_HPR
(MIC_R)
V_HPL
(MIC_L)
VBUS
VBUS
0.1uF
DM
DP
DP
MIC
VIDEO
1uF
DM
ID
Micro-USB
connector
ID
RXD
UART
TXD
GND
GND
GND
Caution:
(1) Connect a capacitor higher than 1 μF to VBUSOUT
(2) Pull Up supply for CHG_DETB (open drain) should be the same VDD as the LSI. Since Pch
protector diode is connected to CHG_DETB, when VDD is OFF, latch up may occur when the signal
level turns high by the pull up.
(3) Make sure to connect capacitor (C cut) to VIDEO pin.
(4) TEST should be either GND or Open.
No.A2221-13/14
LC824204-13YB
Package Dimensions
WLCSP 25pin 2.07 mm  2.07 mm, 0.4 mm pitch
unit : mm
WLCSP25 2.07x2.07 / WLP25
CASE 567EF
ISSUE O
ORDERING INFORMATION
Device
LC824204-13YB-VH
Package
WLP25(2.07X2.07)
(Pb-Free / Halogen Free)
Shipping (Qty / Packing)
4000 / Tape & Reel
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A2221-14/14
Similar pages