TI1 DP83630SQX/NOPB Dp83630 precision phyterâ ¢ - ieee 1588 precision time protocol transceiver Datasheet

DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
DP83630 Precision PHYTER™ - IEEE 1588 Precision Time Protocol Transceiver
Check for Samples: DP83630
1 Introduction
1.1
Features
123
• IEEE 1588 V1 and V2 Supported
• UDP/IPv4, UDP/IPv6, and Layer2 Ethernet
Packets Supported
• IEEE 1588 Clock Synchronization
• Selectable Frequency Synchronized Low Jitter
Clock Output
• Timestamp Resolution of 8 ns
• Allows Sub 10 ns Synchronization to Master
Reference
• 12 IEEE 1588 GPIOs for Trigger or Capture
• Deterministic, Low Transmit and Receive
Latency
• Dynamic Link Quality Monitoring
• TDR Based Cable Diagnostic and Cable Length
Detection
• 10/100 Mb/s Packet BIST (Built in Self Test)
• Error-Free Operation up to 150 Meters CAT5
Cable
1.2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ESD Protection - 8 kV Human Body Model
2.5 V and 3.3 V I/Os and MAC Interface
Auto-MDIX for 10/100 Mbps
Auto-Crossover in Forced Modes of Operation
RMII Rev. 1.2 and MII MAC Interface
RMII Master Mode
25 MHz MDC and MDIO Serial Management
Interface
IEEE 802.3u 100BASE-FX Fiber Interface
IEEE 1149.1 JTAG
Programmable LED Support for Link, 10 /100
Mb/s Mode, Duplex, Activity, and Collision
Detect
Optional 100BASE-TX Fast Link-Loss Detection
Industrial Temperature Range
48 Pin WQFN Package (7mm) x (7mm)
Applications
Telecom
– Basestation
– Pico/Femto Cells
Factory Automation
– Ethernet/IP
– CIP Sync
Test and Measurement
– LXI Standard
Video Synchronization
Real Time Networking
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PHYTER is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Products conform to
specifications per the terms of the Texas Instruments standard warranty. Production
processing does not necessarily include testing of all parameters.
Copyright © 2010–2013, Texas Instruments Incorporated
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
1.3
www.ti.com
Description
The DP83630 Precision PHYTER™ device delivers the highest level of precision clock synchronization for
real time industrial connectivity based on the IEEE 1588 standard. The DP83630 has deterministic, low
latency and allows choice of microcontroller with no hardware customization required. The integrated 1588
functionality allows system designers the flexibility and precision of a close to the wire timestamp. The
three key 1588 features supported by the device are:
— Packet time stamps for clock synchronization
— Integrated IEEE 1588 synchronized low jitter clock generation
— Synchronized event triggering and time stamping through GPIO
DP83630 offers innovative diagnostic features unique to Texas Instruments, including dynamic monitoring
of link quality during standard operation for fault prediction. These advanced features allow the system
designer to implement a fault prediction mechanism to detect and warn of deteriorating and changing link
conditions. This single port fast Ethernet transceiver can support both copper and fiber media.
2
Introduction
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
1
.............................................. 1
............................................. 1
1.2
Applications .......................................... 1
1.3
Description ........................................... 2
Device Information ...................................... 5
2.1
System Diagram ..................................... 5
2.2
Block Diagram ....................................... 5
2.3
Key IEEE 1588 Features ............................ 6
Pin Descriptions ....................................... 10
3.1
Pin Layout .......................................... 11
3.2
PACKAGE PIN ASSIGNMENTS ................... 12
3.3
SERIAL MANAGEMENT INTERFACE ............. 13
3.4
MAC DATA INTERFACE ........................... 13
3.5
CLOCK INTERFACE ............................... 14
3.6
LED INTERFACE .................................. 15
3
4
4.23
Introduction
1.1
2
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Features
3.7
IEEE 1588 EVENT/TRIGGER/CLOCK INTERFACE
3.8
JTAG INTERFACE
......................................................
.................................
3.9
RESET AND POWER DOWN ......................
3.10 STRAP OPTIONS ..................................
3.11 10 Mb/s AND 100 Mb/s PMD INTERFACE ........
3.12 POWER SUPPLY PINS ............................
Electrical Specifications .............................
4.1
Absolute Maximum Ratings ........................
4.2
Recommended Operating Conditions ..............
4.3
AC and DC Specifications ..........................
4.4
DC Specifications ..................................
4.5
AC Specifications — Power Up Timing ............
4.6
AC Specifications — Reset Timing .................
4.7
4.8
4.32
4.33
4.34
4.35
4.36
19
19
19
5
20
21
22
AC Specifications — MII Serial Management Timing
......................................................
23
AC Specifications — 100 Mb/s MII Transmit Timing
26
AC Specifications — 10 Mb/s MII Receive Timing .
AC Specifications — 10BASE-T MII Transmit
Timing (Start of Packet) ............................
AC Specifications — 10BASE-T MII Transmit
Timing (End of Packet) .............................
AC Specifications — 10BASE-T MII Receive Timing
(Start of Packet) ....................................
AC Specifications — 10BASE-T MII Receive Timing
(End of Packet) .....................................
26
4.20
4.31
19
AC Specifications — 10 Mb/s MII Transmit Timing
4.19
4.30
18
4.16
4.17
4.18
4.29
18
4.15
4.14
4.28
16
23
4.13
4.27
16
AC Specifications — 100 Mb/s MII Receive Timing
AC Specifications — 100BASE-TX and 100BASEFX MII Transmit Packet Latency Timing ...........
AC Specifications — 100BASE-TX and 100BASEFX MII Transmit Packet Deassertion Timing .......
AC Specifications — 100BASE-TX Transmit Timing
(tR/F & Jitter) ........................................
AC Specifications — 100BASE-TX and 100BASEFX MII Receive Packet Latency Timing ............
AC Specifications — 100BASE-TX and 100BASEFX MII Receive Packet Deassertion Timing .......
4.12
4.26
15
23
4.11
4.25
15
......................................................
4.9
4.10
4.24
...
......
24
24
25
6
25
26
27
27
28
28
4.21
AC Specifications — 10 Mb/s Heartbeat Timing
28
4.22
AC Specifications — 10 Mb/s Jabber Timing
29
...........................................
5.1
MEDIA CONFIGURATION .........................
5.2
AUTO-NEGOTIATION ..............................
5.3
AUTO-MDIX ........................................
5.4
AUTO-CROSSOVER IN FORCED MODE .........
5.5
PHY ADDRESS ....................................
5.6
LED INTERFACE ...................................
5.7
HALF DUPLEX vs. FULL DUPLEX ................
5.8
INTERNAL LOOPBACK ............................
5.9
POWER DOWN/INTERRUPT ......................
5.10 ENERGY DETECT MODE .........................
5.11 LINK DIAGNOSTIC CAPABILITIES ................
5.12 BIST ................................................
MAC Interface ..........................................
6.1
MII INTERFACE ....................................
6.2
REDUCED MII INTERFACE .......................
6.3
SINGLE CLOCK MII MODE ........................
Configuration
6.4
7
8
AC Specifications — 10BASE-T Normal Link Pulse
Timing ..............................................
AC Specifications — Auto-Negotiation Fast Link
Pulse (FLP) Timing .................................
AC Specifications — 100BASE-TX Signal Detect
Timing ..............................................
AC Specifications — 100 Mb/s Internal Loopback
Timing ..............................................
AC Specifications — 10 Mb/s Internal Loopback
Timing ..............................................
AC Specifications — RMII Transmit Timing (Slave
Mode) ...............................................
AC Specifications — RMII Transmit Timing (Master
Mode) ...............................................
AC Specifications — RMII Receive Timing (Slave
Mode) ...............................................
AC Specifications — RMII Receive Timing (Master
Mode) ...............................................
AC Specifications — RX_CLK Timing (RMII Master
Mode) ...............................................
AC Specifications — CLK_OUT Timing (RMII Slave
Mode) ...............................................
AC Specifications — Single Clock MII (SCMII)
Transmit Timing ....................................
AC Specifications — Single Clock MII (SCMII)
Receive Timing .....................................
AC Specifications — 100 Mb/s X1 to TX_CLK
Timing ..............................................
29
29
30
30
31
31
32
33
34
34
35
35
36
36
37
37
37
40
40
40
41
43
44
44
44
45
49
50
50
51
52
IEEE 802.3u MII SERIAL MANAGEMENT
INTERFACE ........................................ 53
.........................
............................
Architecture .............................................
7.1
100BASE-TX TRANSMITTER ......................
7.2
100BASE-TX RECEIVER ..........................
7.3
100BASE-FX OPERATION .........................
7.4
10BASE-T TRANSCEIVER MODULE ..............
Reset Operation ........................................
8.1
HARDWARE RESET ...............................
8.2
FULL SOFTWARE RESET .........................
6.5
PHY CONTROL FRAMES
6.6
PHY STATUS FRAMES
Contents
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
54
55
56
56
59
63
64
67
67
67
3
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
9
10
4
www.ti.com
......................................
........................................
Design Guidelines .....................................
9.1
TPI NETWORK CIRCUIT ..........................
9.2
FIBER NETWORK CIRCUIT .......................
9.3
ESD PROTECTION ................................
9.4
CLOCK IN (X1) RECOMMENDATIONS ...........
Register Block .........................................
10.1 REGISTER DEFINITION ...........................
............... 91
..................... 102
LINK DIAGNOSTICS REGISTERS - PAGE 2 .... 103
PTP 1588 BASE REGISTERS - PAGE 4 ......... 110
8.3
SOFT RESET
67
10.2
EXTENDED REGISTERS - PAGE 0
8.4
PTP RESET
67
10.3
TEST REGISTERS - PAGE 1
68
10.4
68
10.5
10.6
69
69
69
72
79
10.7
PTP 1588 CONFIGURATION REGISTERS - PAGE
5 ................................................... 118
PTP 1588 CONFIGURATION REGISTERS - PAGE
6 ................................................... 126
Revision History
Contents
...........................................
130
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
2 Device Information
System Diagram
IEEE 1588
Triggered
Events
MPU/CPU
DP83630
10/100 Mb/s
Precision PHYTER
MII or RMII
Fiber
Transceiver
10BASE-T
100BASE-TX
or
100BASE-FX
Status
LEDs
Clock
2.2
RJ45
Media Access Control
(MAC)
IEEE 1588 clocks, events, triggers
IEEE 1588
Captured
Events
Magnetics
2.1
Block Diagram
RX_CLK
RXD[3:0]
RX_DV
RX_ER
COL
MDC
MDIO
TX_EN
TXD[3:0]
TX_CLK
SERIAL
MANAGEMENT
CRS/CRS_DV
MII/RMII
MII/RMII INTERFACE
TX_DATA
TX_CLK
RX_CLK
RX_DATA
MANAGEMENT REGISTERS
10BASE -T
&
100BASE-TX
10BASE -T
&
100BASE-TX
AUTO-NEGOTIATION
REGISTERS
TRANSMIT BLOCK
RECEIVE BLOCK
CLOCK
GENERATION
IEEE 1588
DAC
ADC
ANALOG SIGNAL
PROCESSOR
BOUNDARY
SCAN
JTAG
LED
DRIVERS
AUTO-MDIX
TD+/-
RD+/-
SYSTEM CLOCK
REFERENCE
GPIO
LEDS
Figure 2-1. DP83630 Functional Block Diagarm
Device Information
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
5
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
2.3
www.ti.com
Key IEEE 1588 Features
IEEE 1588 provides a time synchronization protocol, often referred to as the Precision Time Protocol
(PTP), which synchronizes time across an Ethernet network. DP83630 supports IEEE 1588 Real Time
Ethernet applications by providing hardware support for three time critical elements.
• IEEE 1588 synchronized clock generation
• Packet timestamps for clock synchronization
• Event triggering and timestamping through GPIO
By combining the above capabilities, the DP83630 provides advanced and flexible support for IEEE 1588
for use in a highly accurate IEEE 1588 system.
The DP83630 provides features for controlling the clock operation in Slave mode. The clock value can be
updated to match the Master clock in several ways. In addition, the clock can be programmed to adjust its
frequency to compensate for drift.
The DP83630 supports real time triggering activities and captures real time events to report to the
microcontroller. Controlled devices can be connected to the DP83630 through the available GPIO.
The IEEE 1588 features are briefly presented below. For a more detailed discussion on configuring
the IEEE 1588 features, refer to the Software Development Guide for the DP83630.
Real TIme Actions
Microcontroller
or Microprocessor
GPIO
Clock
IEEE 1588 Clock
Application Code
IEEE 1588 Code
MDIO
IEEE 1588 Control
OS
MAC
MII
IEEE 1588
Packet Detection
and Processing
PHY
DP83630
LAN
Figure 2-2. DP83630 Example System Application
6
Device Information
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
2.3.1
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
IEEE 1588 SYNCHRONIZED CLOCK
The DP83630 provides several mechanisms for updating the IEEE 1588 clock based on the
synchronization protocol required. These methods are listed below.
• Directly Read/Writable
• Adjustable by Add/Subtract
• Frequency Scalable
• Temporary Frequency Control
The clock consists of the following fields: Seconds (32–bit field), Nanoseconds (30–bit field), and
Fractional Nanoseconds (units of 2-32 ns).
A direct set of the time value can be done by setting a new time value. A step adjustment value in
nanoseconds may be added to the current value. Note that the adjustment value can be positive or
negative.
The clock can be programmed to operate at an adjusted frequency value by programming a rate
adjustment value. The clock can also be programmed to perform a temporary adjusted frequency value by
including a rate adjustment duration. The rate adjustment allows for correction on the order of 2-32 ns per
reference clock cycle. The frequency adjustment will allow the clock to correct the offset over time,
avoiding any potential side-effects caused by a step adjustment in the time value.
The method used to update the clock value may depend on the difference in the values. For example, at
the initial synchronization attempt, the clocks may be very far apart, and therefore require a step
adjustment or a direct time set. Later, when clocks are very close in value, the temporary rate adjustment
method may be the best option.
The clock does not support negative time values. If negative time is required in the system, software will
have to make conversions from the PHY clock time to actual time.
The clock also does not support the upper 16-bits of the seconds field as defined by the specification
(Version 2 specifies a 48-bit seconds field). If this value is required to be greater than 0, it will have to be
handled by software. Since a rollover of the seconds field only occurs every 136 years, it should not be a
significant burden to software.
2.3.1.1
IEEE 1588 Clock Output
The DP83630 provides for a synchronized clock signal for use by external devices. The output clock
signal can be any frequency generated from 250 MHz divided by n, where n is an integer in the range of 2
to 255. This provides nominal frequencies from 125 MHz down to 980.4 kHz. The clock output signal is
controlled by the PTP_COC register. The output clock signal is generated using the rate information in the
PTP_RATE registers and is therefore frequency accurate to the 1588 clock time of the device. In addition,
if clock time adjustments are made using the Temporary Rate capabilities, then all time adjustments will
be tracked by the output clock signal as well. Note that any step adjustment in the 1588 clock time will not
be accurately represented on the 1588 clock output signal.
2.3.1.2
IEEE 1588 Clock Input
The IEEE 1588 PTP logic operates on a nominal 125 MHz reference clock generated by an internal Phase
Generation Module (PGM). However, options are available to use a divided-down version of the PGM
clock to reduce power consumption at the expense of precision, or to use an external reference clock of
up to 125 MHz in the event the 1588 clock is tracked externally.
Device Information
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
7
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
2.3.2
www.ti.com
PACKET TIMESTAMPS
2.3.2.1
IEEE 1588 Transmit Packet Parser and Timestamp
The IEEE 1588 transmit parser monitors transmit packet data to detect IEEE 1588 Version 1 and Version
2 Event messages. The transmit parser can detect PTP Event messages transported directly in Layer2
Ethernet packets as well as in UDP/IPv4 and UDP/IPv6 packets. Upon detection of a PTP Event
Message, the device will capture the transmit timestamp and provide it to software.
Since software knows the order of packet transmission, only the timestamp is recorded (there is no need
to record sequence number or other information). The device can buffer four timestamps.
If enabled, an interrupt may be generated upon a Transmit Timestamp Ready.
2.3.2.1.1 One-Step Operation
In some cases, the transmitter can be set to operate in a One-Step mode. For Sync Messages, a OneStep device can automatically insert timestamp information in the outgoing packet. This eliminates the
need for software to read the timestamp and send a follow up message.
2.3.2.2
IEEE 1588 Receive Packet Parser and Timestamp
The IEEE 1588 receive parser monitors receive packet data to detect IEEE 1588 Version 1 and Version 2
Event messages. The receive parser can detect PTP Event messages transported directly in Ethernet
packets as well as in UDP/IPv4 and UDP/IPv6 packets. Upon detection of a PTP Event message, the
device will capture the receive timestamp and provide the timestamp value to software. In addition to the
timestamp, the device will record the 16-bit SequenceId, the 4-bit messageType field, and generate a 12bit hash value for octets 20-29 of the PTP event message. The device can buffer four timestamps.
An interrupt will be generated, if enabled, upon a Receive Timestamp Ready.
2.3.2.2.1 Receive Timestamp Insertion
The DP83630 can deliver the timestamp to software by inserting the timestamp in the received packet.
This allows for a simple method to deliver the packet to software without having to match the timestamp to
the correct packet. This also eliminates the need to read the receive timestamp through the Serial
Management Interface.
2.3.2.3
NTP Packet Timestamp
The DP83630 may be programmed to timestamp NTP packets instead of PTP packets. This operation is
enabled by setting the NTP_TS_EN control in the PTP_TXCFG0 register. When configured for NTP
timestamps, the DP83630 will timestamp packets with the NTP UDP port number rather than the PTP port
number (note that the device cannot be configured to timestamp both PTP and NTP packets). One-Step
operation is not supported for NTP timestamps, so transmit timestamps cannot be inserted directly into
outgoing NTP packets. Timestamp insertion is available for receive timestamps but must use a single,
fixed location.
2.3.3
EVENT TRIGGERING AND TIMESTAMPING
2.3.3.1
IEEE 1588 Event Triggering
The DP83630 is capable of being programmed to generate a trigger signal on an output pin based on the
IEEE 1588 time value. Each trigger can be programmed to generate a one-time rising or falling edge, a
single pulse of programmable width, or a periodic signal.
For each trigger, the microcontroller specifies the desired GPIO and time that the activity is to occur. The
trigger is generated when the internal IEEE 1588 clock matches the desired activation time.
8
Device Information
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
The device supports up to 8 trigger signals which can be output on any of the GPIO signal pins. Multiple
triggers may be assigned to a single GPIO, allowing generation of more complex waveforms (i.e. a
sequence of varying width pulses). The trigger signals are OR’ed together to form a combined signal.
The triggers are configured through the PTP Trigger Configuration Registers. The trigger time and width
settings are controlled through the PTP Control and Time Data registers.
The DP83630 can be programmed to output a Pulse-Per-Second (PPS) signal using the trigger functions.
2.3.3.2
IEEE 1588 Event Timestamping
The DP83630 can be programmed to timestamp an event by monitoring an input signal. The event can be
monitored for rising edge, falling edge, or either. The Event Timestamp Unit can monitor up to eight events
which can be set to any of the GPIO signal pins. PTP event timestamps are stored in a queue which
allows storage of up to eight timestamps.
When an event timestamp is available, the device will set the EVENT_RDY bit in the PTP Status Register.
The PTP Event Status Register (PTP_ESTS) provides detailed information on the next available event
timestamp, including information on the event number, rise/fall direction, and indication of events missed
due to overflow of the devices Event queue.
Event timestamp values should be adjusted by 35 ns (3 times period of the IEEE 1588 reference clock
frequency of 125 MHz + 11 ns) to compensate for input path and synchronization delays.
The Event Timestamp Unit is configured through the PTP Event Configuration Register (PTP_EVNT).
2.3.4
PTP INTERRUPTS
The PTP module may interrupt the system using the PWRDOWN/INTN pin on the device, shared with
other interrupts from the PHY. As an alternative, the device may be programmed to use a GPIO pin to
generate PTP interrupts separate from other PHY interrupts.
2.3.5
GPIO
The DP83630 features 12 IEEE 1588 GPIO pins. These GPIO pins allow for event monitoring, triggering,
interrupts, and a clock output. The LED pins comprise 3 of the 12 GPIO pins. If an LED pin is to be used
as a GPIO, its LED function must be disabled prior to configuring the GPIO function.
Device Information
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
9
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
3 Pin Descriptions
The DP83630 pins are classified into the following interface categories (each interface is described in the
sections that follow):
• Serial Management Interface
• MAC Data Interface
• Clock Interface
• LED Interface
• GPIO Interface
• JTAG Interface
• Reset and Power Down
• Strap Options
• 10/100 Mb/s PMD Interface
• Power and Ground pins
All DP83630 signal pins are I/O cells regardless of the particular use. The definitions below define the
functionality of the I/O cells for each pin.
10
Type: I
Input
Type: O
Output
Type: I/O
Input/Output
Type: OD
Open Drain
Type: PD
Internal Pulldown
Type: PU
Internal Pullup
Type: S
Strapping Pin (All strap pins have weak internal pull-ups or pull-downs. If the default strap
value is to be changed then an external 2.2 kΩ resistor should be used. Please see Strap
Options for details.)
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
IO_VSS
RXD_0
RXD_1
RXD_2
RXD_3
COL
RX_ER
CRS/CRS_DV
RX_DV
RX_CLK
GPIO9
Pin Layout
IO_VDD
3.1
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
48
47
46
45
44
43
42
41
40
39
38
37
TX_CLK
1
36
GPIO8
TX_EN
2
35
IO_CORE_VSS
TXD_0
3
34
X1
TXD_1
4
33
X2
DP83630SQ
TXD_2
5
32
IO_VDD
31
MDC
TDO
9
28
LED_LINK
TMS
10
27
LED_SPEED/FX_SD
TRST#
11
26
LED_ACT
TDI
12
25
GPIO4
13
14
15
16
17
18
19
20
21
22
23
24
CLK_OUT
RESET_N
GPIO3
29
GPIO2
DAP = GND
GPIO1
8
VREF
TCK
ANA33VDD
MDIO
ANAVSS
30
TD+
48-pin LLP Package
TD-
7
CD_VSS
PWRDOWN/INTN
RD+
6
RD-
TXD_3
TOP VIEW
(not to scale)
Figure 3-1. Top View
Package Number RHS0048A
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
11
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
3.2
PACKAGE PIN ASSIGNMENTS
RHS0048A Pin #
(1)
12
www.ti.com
Pin Name
RHS0048A Pin #
Pin Name
1
TX_CLK
26
LED_ACT
2
TX_EN
27
LED_SPEED/FX_SD
3
TXD_0
28
LED_LINK
4
TXD_1
29
RESET_N
5
TXD_2
30
MDIO
6
TXD_3
31
MDC
7
PWRDOWN/INTN
32
IO_VDD
8
TCK
33
X2
9
TDO
34
X1
10
TMS
35
IO_CORE_VSS
11
TRST#
36
GPIO8
12
TDI
37
GPIO9
13
RD-
38
RX_CLK
14
RD+
39
RX_DV
15
CD_VSS
40
CRS/CRS_DV
16
TD-
41
RX_ER
17
TD+
42
COL
18
ANAVSS
43
RXD_3
19
ANA33VDD
44
RXD_2
20
VREF
45
RXD_1
21
GPIO1
46
RXD_0
22
GPIO2
47
IO_VSS
23
GPIO3
48
IO_VDD
24
CLK_OUT
25
GPIO4
NC or GND (1)
DAP
Die Attach Pad (DAP) provides thermal dissipation. Connection to GND plane recommended.
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
3.3
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
SERIAL MANAGEMENT INTERFACE
Signal Name
Pin Name
Type
Pin #
Description
MDC
MDC
I
31
MANAGEMENT DATA CLOCK: Synchronous clock to the MDIO
management data input/output serial interface which may be asynchronous
to transmit and receive clocks. The maximum clock rate is 25 MHz with no
minimum clock rate.
MDIO
MDIO
I/O
30
MANAGEMENT DATA I/O: Bi-directional management instruction/data
signal that may be sourced by the station management entity or the PHY.
This pin requires a 1.5 kΩ pullup resistor. Alternately, an internal pullup may
be enabled by setting bit 3 in the CDCTRL1 register.
3.4
MAC DATA INTERFACE
Signal Name
Type
Pin #
Description
TX_CLK
TX_CLK
Pin Name
O
1
MII TRANSMIT CLOCK: 25 MHz Transmit clock output in 100 Mb/s mode
or 2.5 MHz in 10 Mb/s mode derived from the 25 MHz reference clock. The
MAC should source TX_EN and TXD[3:0] using this clock.
RMII MODE: Unused in RMII Slave mode. The device uses the X1
reference clock input as the 50 MHz reference for both transmit and
receive. For RMII Master mode, the device outputs the internally generated
50 MHz reference clock on this pin.
This pin provides an integrated 50 ohm signal termination, making external
termination resistors unnecessary.
TX_EN
TX_EN
I, PD
2
MII TRANSMIT ENABLE: Active high input indicates the presence of valid
data inputs on TXD[3:0].
RMII TRANSMIT ENABLE: Active high input indicates the presence of valid
data on TXD[1:0].
TXD_0
TXD_1
TXD_2
TXD_3
TXD_0
TXD_1
TXD_2
TXD_3
I
I
I
I, PD
3
4
5
6
MII TRANSMIT DATA: Transmit data MII input pins, TXD[3:0], that accept
data synchronous to the TX_CLK (2.5 MHz in 10 Mb/s mode or 25 MHz in
100 Mb/s mode).
RMII TRANSMIT DATA: Transmit data RMII input pins, TXD[1:0], that
accept data synchronous to the 50 MHz reference clock.
RX_CLK
RX_CLK
O
38
MII RECEIVE CLOCK: Provides the 25 MHz recovered receive clocks for
100 Mb/s mode and 2.5 MHz for 10 Mb/s mode.
RMII MODE: Unused in RMII Slave mode. The device uses the X1
reference clock input as the 50 MHz reference for both transmit and
receive. For RMII Master mode, the device outputs the internally generated
50 MHz reference clock on this pin.
This pin provides an integrated 50 ohm signal termination, making external
termination resistors unnecessary.
RX_DV
RX_DV
O, PD
39
MII RECEIVE DATA VALID: Asserted high to indicate that valid data is
present on the corresponding RXD[3:0].
RMII RECEIVE DATA VALID: This signal provides the RMII Receive Data
Valid indication independent of Carrier Sense.
This pin provides an integrated 50 ohm signal termination, making external
termination resistors unnecessary.
RX_ER
RX_ER
S, O, PU
41
MII RECEIVE ERROR: Asserted high synchronously to RX_CLK to indicate
that an invalid symbol has been detected within a received packet in 100
Mb/s mode.
RMII RECEIVE ERROR: Asserted high synchronously to X1 whenever a
media error is detected, and RX_DV is asserted in 100 Mb/s mode.
This pin is not required to be used by a MAC in RMII mode, since the PHY
is required to corrupt data on a receive error.
This pin provides an integrated 50 ohm signal termination, making external
termination resistors unnecessary.
RXD_0
RXD_1
RXD_2
RXD_3
RXD_0
RXD_1
RXD_2
RXD_3
S, O, PD
46
45
44
43
MII RECEIVE DATA: Nibble wide receive data signals driven synchronously
to the RX_CLK (25 MHz for 100 Mb/s mode, 2.5 MHz for 10 Mb/s mode).
RXD[3:0] signals contain valid data when RX_DV is asserted.
RMII RECEIVE DATA: 2-bits receive data signals, RXD[1:0], driven
synchronously to the 50 MHz reference clock.
These pins provide integrated 50 ohm signal terminations, making external
termination resistors unnecessary.
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
13
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Signal Name
Type
Pin #
Description
CRS/CRS_DV
CRS/CRS_DV
S, O, PU
40
MII CARRIER SENSE: Asserted high to indicate the receive medium is
non-idle.
RMII CARRIER SENSE/RECEIVE DATA VALID: This signal combines the
RMII Carrier and Receive Data Valid indications. For a detailed description
of this signal, see the RMII Specification.
This pin provides an integrated 50 ohm signal termination, making external
termination resistors unnecessary.
COL
COL
S, O, PU
42
MII COLLISION DETECT: Asserted high to indicate detection of a collision
condition (simultaneous transmit and receive activity) in 10 Mb/s and 100
Mb/s Half Duplex Modes.
While in 10BASE-T Half Duplex mode with heartbeat enabled this pin is
also asserted for a duration of approximately 1µs at the end of transmission
to indicate heartbeat (SQE test).
In Full Duplex Mode, for 10 Mb/s or 100 Mb/s operation, this signal is
always logic 0. There is no heartbeat function during 10 Mb/s full duplex
operation.
RMII COLLISION DETECT: Per the RMII Specification, no COL signal is
required. The MAC will recover CRS from the CRS_DV signal and use that
along with its TX_EN signal to determine collision.
This pin provides an integrated 50 ohm signal termination, making external
termination resistors unnecessary.
3.5
Pin Name
www.ti.com
CLOCK INTERFACE
Signal Name
Type
Pin #
Description
X1
X1
I
34
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock reference
input for the DP83630 and must be connected to a 25 MHz 0.005% (±50
ppm) clock source. The DP83630 supports either an external crystal
resonator connected across pins X1 and X2 or an external CMOS-level
oscillator source connected to pin X1 only.
RMII REFERENCE CLOCK: For RMII Slave Mode, this pin must be
connected to a 50 MHz 0.005% (±50 ppm) CMOS-level oscillator source. In
RMII Master Mode, a 25 MHz reference is required, either from an external
crystal resonator connected across pins X1 and X2 or from an external
CMOS-level oscillator source connected to pin X1 only.
X2
X2
O
33
CRYSTAL OUTPUT: This pin is the primary clock reference output to
connect to an external 25 MHz crystal resonator device. This pin must be
left unconnected if an external CMOS oscillator clock source is used.
CLK_OUT
CLK_OUT
I/O, PD
24
CLOCK OUTPUT: This pin provides a highly configurable system clock,
which may have one of four sources:
1. Relative to the internal PTP clock, with a default frequency of 25 MHz
(default)
2. 50 MHz RMII reference clock in RMII Master Mode
3. 25 MHz Receive Clock (same as RX_CLK) in 100 Mb mode
4. 25 MHz or 50 MHz pass-through of X1 reference clock
CLOCK INPUT: This pin is used to input an external IEEE 1588 reference
clock for use by the IEEE 1588 logic. The CLK_OUT_EN strap should be
disabled in the system to prevent possible contention. The PTP_CLKSRC
register must be configured prior to enabling the IEEE 1588 function in
order to allow correct operation.
14
Pin Name
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
3.6
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
LED INTERFACE
The DP83630 supports three configurable LED pins. The LEDs support two operational modes which are
selected by the LED mode strap and a third operational mode which is register configurable. The
definitions for the LEDs for each mode are detailed below.
Signal Name
LED_LINK
Pin Name
LED_LINK
Type
Pin #
Description
S, O, PU
28
LINK LED: In Mode 1, this pin indicates the status of the LINK. The LED
will be ON when Link is good.
LINK/ACT LED: In Mode 2 and Mode 3, this pin indicates transmit and
receive activity in addition to the status of the Link. The LED will be ON
when Link is good. It will blink when the transmitter or receiver is active.
LED_SPEED
LED_SPEED/FX_S
D
S, O, PU
27
SPEED LED: The LED is ON when device is in 100 Mb/s and OFF when in
10 Mb/s. Functionality of this LED is independent of mode selected.
LED_ACT
LED_ACT
S, O, PU
26
ACTIVITY LED: In Mode 1, this pin is the Activity LED which is ON when
activity is present on either Transmit or Receive.
COLLISION/DUPLEX LED: In Mode 2, this pin by default indicates
Collision detection. In Mode 3, this LED output indicates Full-Duplex status.
3.7
IEEE 1588 EVENT/TRIGGER/CLOCK INTERFACE
Signal Name
Pin Name
Type
Pin #
Description
GPIO1
GPIO2
GPIO3
GPIO4
GPIO1
GPIO2
GPIO3
GPIO4
I/O, PD
21
22
23
25
General Purpose I/O: These pins may be used to signal or detect events.
GPIO5
GPIO6
I/O, PU
26
27
GPIO7
LED_ACT
LED_SPEED/FX_S
D
LED_LINK
General Purpose I/O: These pins may be used to signal or detect events.
Care should be taken when designing systems that use LEDs but use these
pins as GPIOs. To disable the LED functions, refer to LED Direct Control
Register (LEDCR).
GPIO8
GPIO9
GPIO8
GPIO9
I/O, PD
36
37
General Purpose I/O: These pins may be used to signal or detect events.
GPIO10
GPIO11
TDO
TDI
I/O, PU
9
12
General Purpose I/O: These pins may be used to signal or detect events.
Care should be taken when designing systems that use the JTAG interface
but use these pins as GPIOs.
GPIO12
CLK_OUT
I/O, PD
24
General Purpose I/O: This pin may be used to signal or detect events or
may output a programmable clock signal synchronized to the internal IEEE
1588 clock or may be used as an input for an externally generated IEEE
1588 reference clock. If the system does not require the CLK_OUT signal,
the CLK_OUT output should be disabled via the CLK_OUT_EN strap.
Type
Pin #
I, PU
8
3.8
JTAG INTERFACE
Signal Name
TCK
28
Pin Name
TCK
Description
TEST CLOCK
This pin has a weak internal pullup.
TDO
TDO
O
9
TEST OUTPUT
TMS
TMS
I, PU
10
TEST MODE SELECT
This pin has a weak internal pullup.
TRST#
TRST#
I, PU
11
TDI
TDI
I, PU
12
TEST RESET: Active low test reset.
This pin has a weak internal pullup.
TEST DATA INPUT
This pin has a weak internal pullup.
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
15
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
3.9
www.ti.com
RESET AND POWER DOWN
Signal Name
Pin Name
Type
Pin #
Description
RESET_N
RESET_N
I, PU
29
RESET: Active Low input that initializes or re-initializes the DP83630.
Asserting this pin low for at least 1 µs will force a reset process to occur.
All internal registers will re-initialize to their default states as specified for
each bit in the Register Block section. All strap options are re-initialized as
well.
PWRDOWN/INTN
PWRDOWN/INTN
I, PU
7
The default function of this pin is POWER DOWN.
POWER DOWN: Asserting this signal low enables the DP83630 Power
Down mode of operation. In this mode, the DP83630 will power down and
consume minimum power. Register access will be available through the
Management Interface to configure and power up the device.
INTERRUPT: This pin may be programmed as an interrupt output instead
of a Powerdown input. In this mode, Interrupts will be asserted low using
this pin. Register access is required for the pin to be used as an interrupt
mechanism. See Interrupt Mechanisms for more details on the interrupt
mechanisms.
3.10 STRAP OPTIONS
The DP83630 uses many of the functional pins as strap options to place the device into specific modes of
operation. The values of these pins are sampled at power up or hard reset. During software resets, the
strap options are internally reloaded from the values sampled at power up or hard reset. The strap option
pin assignments are defined below. The functional pin name is indicated in parentheses.
A 2.2 kΩ resistor should be used for pull-down or pull-up to change the default strap option. If the default
option is required, then there is no need for external pull-up or pull down resistors. Since these pins may
have alternate functions after reset is deasserted, they should not be connected directly to VCC or GND.
Signal Name
PHYAD0
PHYAD1
PHYAD2
PHYAD3
PHYAD4
16
Pin Name
COL
RXD_3
RXD_2
RXD_1
RXD_0
Type
S,
S,
S,
S,
S,
O,
O,
O,
O,
O,
PU
PD
PD
PD
PD
Pin #
Description
42
43
44
45
46
PHY ADDRESS [4:0]: The DP83630 provides five PHY address pins,
the state of which are latched into the PHYCTRL register at system
Hardware-Reset.
The DP83630 supports PHY Address strapping values 0 (<00000>)
through 31 (<11111>).A PHY Address of 0 puts the part into the MII
Isolate Mode. The MII isolate mode must be selected by strapping
PHY Address 0; changing to Address 0 by register write will not put the
PHY in the MII isolate mode.
PHYAD[0] pin has weak internal pull-up resistor.
PHYAD[4:1] pins have weak internal pull-down resistors.
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
Signal Name
AN_EN
AN1
AN0
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Pin Name
LED_LINK
LED_SPEED/FX_S
D
LED_ACT
Type
Pin #
Description
S, O, PU
S, O, PU
28
27
S, O, PU
26
AUTO-NEGOTIATION ENABLE: When high, this enables AutoNegotiation with the capability set by AN0 and AN1 pins. When low, this
puts the part into Forced Mode with the capability set by AN0 and AN1
pins.
AN0 / AN1: These input pins control the forced or advertised operating
mode of the DP83630 according to the following table. The value on
these pins is set by connecting the input pins to GND (0) or VCC (1)
through 2.2 kΩ resistors. These pins should NEVER be connected
directly to GND or VCC.
The value set at this input is latched into the DP83630 at HardwareReset.
The float/pull-down status of these pins are latched into the Basic Mode
Control Register and the Auto_Negotiation Advertisement Register
during Hardware-Reset.
The default is 111 since these pins have internal pull-ups.
FIBER MODE DUPLEX SELECTION: If Fiber mode is strapped using
the FX_EN_Z pin (FX_EN_Z = 0), the AN0 strap value is used to select
half or full duplex. AN_EN and AN1 are ignored in Fiber mode since it
is 100 Mb only and does not support Auto-Negotiation. In Fiber mode,
AN1 should not be connected to any system components except the
fiber transceiver.
FX_EN_
Z
AN_EN
AN1
AN0
Forced Mode
1
0
0
0
10BASE-T, Half-Duplex
1
0
0
1
10BASE-T, Full-Duplex
1
0
1
0
100BASE-TX, Half-Duplex
1
0
1
1
100BASE-TX, Full-Duplex
0
X
X
0
100BASE-FX, Half-Duplex
100BASE-FX, Full-Duplex
0
X
X
1
FX_EN_
Z
AN_EN
AN1
AN0
1
1
0
0
10BASE-T, Half/Full-Duplex
1
1
0
1
100BASE-TX, Half/Full-Duplex
1
1
1
0
100BASE-TX, Full-Duplex
1
1
1
1
10BASE-T, Half/Full-Duplex,
100BASE-TX, Half/Full-Duplex
Advertised Mode
CLK_OUT_EN
GPIO1
S, I, PD
21
CLK_OUT OUTPUT ENABLE: When high, enables clock output on the
CLK_OUT pin at power-up.
FX_EN_Z
RX_ER
S, O, PU
41
FX ENABLE: This strapping option enables 100Base-FX (Fiber) mode.
This mode is disabled by default. An external pull-down will enable
100Base-FX mode.
LED_CFG
CRS/CRS_DV
S, O, PU
40
LED CONFIGURATION: This strapping option determines the mode of
operation of the LED pins. Default is Mode 1. Mode 1 and Mode 2 can
be controlled via the strap option. All modes are configurable via
register access. See Table 5-3 for LED Mode Selection.
MII_MODE
RX_DV
S, O, PD
39
MII MODE SELECT: This strapping option determines the operating
mode of the MAC Data Interface. Default operation is MII Mode with a
value of 0 due to the internal pulldown. Strapping MII_MODE high will
cause the device to be in RMII mode of operation.
MII_MODE
MAC Interface Mode
0
MII Mode
1
RMII Mode
PCF_EN
GPIO2
S, I, PD
22
PHY CONTROL FRAME ENABLE: When high, allows the DP83630 to
respond to PHY Control Frames.
RMII_MAS
TXD_3
S, I, PD
6
RMII MASTER ENABLE: When MII_MODE is strapped high, this
strapping option enables RMII Master mode, in which the DP83630
uses a 25 MHz crystal connection on X1/X2 and generates the 50 MHz
RMII reference clock. If strapped low when MII_MODE is strapped high,
default RMII operation (RMII Slave) is enabled, in which the DP83630
uses a 50 MHz oscillator input on X1 as the RMII reference clock. This
strap option is ignored if the MII_MODE strap is low.
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
17
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
3.11 10 Mb/s AND 100 Mb/s PMD INTERFACE
Signal Name
Pin Name
Type
Pin #
Description
TDTD+
TDTD+
I/O
16
17
Differential common driver transmit output (PMD Output Pair). These
differential outputs are automatically configured to either 10BASE-T or
100BASE-TX signaling.
In Auto-MDIX mode of operation, this pair can be used as the Receive Input
pair.
In 100BASE-FX mode, this pair becomes the 100BASE-FX Transmit pair.
These pins require 3.3V bias for operation.
RDRD+
RDRD+
I/O
13
14
Differential receive input (PMD Input Pair). These differential inputs are
automatically configured to accept either 100BASE-TX or 10BASE-T
signaling.
In Auto-MDIX mode of operation, this pair can be used as the Transmit
Output pair.
In 100BASE-FX mode, this pair becomes the 100BASE-FX Receive pair.
These pins require 3.3V bias for operation.
FX_SD
LED_SPEED/FX_S S, I/O, PU
D
27
FIBER MODE SIGNAL DETECT: This pin provides the Signal Detect input
for 100BASE-FX mode.
3.12 POWER SUPPLY PINS
Signal Name
Pin Name
Type
Pin #
Ground
18
Analog Ground
ANA33VDD
Supply
19
Analog VDD Supply
CD_VSS
Ground
15
Analog Ground
IO_CORE_VSS
IO_CORE_VSS
Ground
35
Digital Ground
IO_VDD
IO_VDD
Supply
32
48
I/O VDD Supply
IO_VSS
IO_VSS
Ground
47
Digital Ground
VREF
VREF
20
Bias Resistor Connection. A 4.87 kΩ 1% resistor should be connected from
VREF to GND.
DAP
DAP
ANAVSS
ANAVSS
ANA33VDD
CD_VSS
(1)
18
Description
No Connect or Connect to GND (1)
Die Attach Pad (DAP) provides thermal dissipation. Connection to GND plane recommended.
Pin Descriptions
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4 Electrical Specifications
4.1
Absolute Maximum Ratings (1) (2) (3)
Supply Voltage (VCC)
-0.5 V to 4.2 V
DC Input Voltage (VIN)
-0.5V to VCC + 0.5V
DC Output Voltage (VOUT)
-0.5V to VCC + 0.5V
Storage Temperature (TSTG )
-65°C to 150°C
Maximum Case Temperature for TA = 85 °C
95 °C
Maximum Die Temperature (Tj)
ESD Rating
(1)
(2)
(3)
4.2
150 °C
(RZAP = 1.5k, CZAP = 120 pF)
8.0 kV
Absolute maximum ratings are those values beyond which the safety of the device cannot be ensured. They are not meant to imply that
the device should be operated at these limits.
For soldering specifications: see product folder at www.ti.com and SNOA549c.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Recommended Operating Conditions
Analog Supply Voltage (VCC)
3.3 Volts ± 0.3V
3.3 Volts ± 10% or
I/O Supply Voltage (VI/O)
2.5 Volts ± 5%
Industrial Temperature (TI)
-40 to 85 °C
Power Dissipation (PD) with VI/O = 3.3 V
290 mW
Power Dissipation (PD) with VI/O = 2.5 V
260 mW
4.3
AC and DC Specifications
Thermal Characteristic
Max
Units
Theta Junction to Case (Tjc)
TBD
°C / W
Theta Junction to Ambient (Tja) degrees Celsius/Watt - No Airflow @ 1.0 W
TBD
°C / W
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
19
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.4
www.ti.com
DC Specifications
Symbol
Pin Types
Parameter
VIH
I
I/O
Input High Voltage
VIL
I
I/O
Input Low Voltage
IIH
I
I/O
IIL
Conditions
Min
Type
Max
2.0
Units
V
VI/O = 3.3 V
0.8
V
VI/O = 2.5 V
0.7
V
Input High Current
VIN = VI/O
10
µA
I
I/O
Input Low Current
VIN = GND
10
µA
VOL
O
I/O
Output Low Voltage
IOL = 4 mA
0.4
V
VOH
O
I/O
Output High Voltage
IOH = -4 mA
IOZ
O
I/O
TRI-STATE Output Leakage Current
VOUT = VI/O or GND
VTPTD_100
PMD Output Pair 100M Transmit Voltage
VTPTDsym
PMD Output Pair 100M Transmit Voltage Symmetry
VTPTD_10
VFXTD_100
VI/O - 0.5
V
-10
1
1.05
V
±2
%
PMD Output Pair 10M Transmit Voltage
2.2
2.5
2.8
V
PMD Output Pair FX 100M Transmit Voltage
0.3
0.5
0.93
V
I
CMOS Input Capacitance
8
COUT1
O
CMOS Output Capacitance
8
SDTHon
PMD Input Pair
100BASE-TX Signal detect turn-on
threshold
SDTHoff
PMD Input Pair
Signal detect turn-off threshold
200
VTH
PMD Input Pair
10BASE-T Receive Threshold
300
Idd100
Supply
100BASE-TX (Full Duplex)
Idd10
Supply
Idd
20
µA
0.95
CIN1
(1)
10
Supply
10BASE-T (Full Duplex)
Power Down Mode
pF
pF
1000
mV diff
pk-pk
mV diff
pk-pk
585
mV
VCC = 3.3 V,
VI/O = 3.3 V,
IOUT = 0 mA (1)
88
mA
VCC = 3.3 V,
VI/O = 2.5 V,
IOUT = 0 mA (1)
84
mA
VCC = 3.3 V,
VI/O = 3.3 V,
IOUT = 0 mA (1)
105
mA
VCC = 3.3 V,
VI/O = 2.5 V,
IOUT = 0 mA (1)
103
mA
CLK_OUT disabled
10
mA
For Idd measurements, outputs are not loaded
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
4.5
AC Specifications — Power Up Timing
Parameter
T2.1.1
T2.1.2
T2.1.3
(1)
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Notes
Min
Post Power Up Stabilization time
prior to MDC preamble for register
accesses (1)
Description
MDIO is pulled high for 32-bit serial
management initialization.
167
ms
Hardware Configuration Latch-in
Time from power up (1)
Hardware Configuration Pins are
described in the Pin Description
section.
167
ms
Hardware Configuration pins
transition to output drivers
Typ
Max
Units
50
ns
In RMII Slave Mode, the minimum Post Power up Stabilization and Hardware Configuration Latch-in times are 84 ms.
Vcc
X1 clock
T2.1.1
Hardware
RESET_N
32 CLOCKS
MDC
T2.1.2
Latch-In of Hardware
Configuration Pins
T2.1.3
Dual Function Pins
Become Enabled As Outputs
INPUT
OUTPUT
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
21
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.6
www.ti.com
AC Specifications — Reset Timing
Parameter
Description
Notes
Min
Typ
Max
Units
T2.2.1
Post RESET Stabilization time prior to
MDC preamble for register accesses
MDIO is pulled high for 32-bit serial
management initialization
3
µs
T2.2.2
Hardware Configuration Latch-in Time
from the Deassertion of RESET (either
soft or hard) (1)
Hardware Configuration Pins are
described in the Pin Description
section
3
µs
50
ns
T2.2.3
Hardware Configuration pins transition
to output drivers
T2.2.4
X1 Clock must be stable for at min.
of 1 µs during RESET pulse low
time.
RESET pulse width
(1)
1
µs
It is important to choose pull-up and/or pull-down resistors for each of the hardware configuration pins that provide fast RC time
constants in order to latch-in the proper value prior to the pin transitioning to an output driver.
Vcc
X1 clock
T2.2.1
T2.2.4
Hardware
RESET_N
32 CLOCKS
MDC
T2.2.2
Latch-In of Hardware
Configuration Pins
T2.2.3
Dual Function Pins
Become Enabled As Outputs
22
input
Electrical Specifications
output
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
4.7
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
AC Specifications — MII Serial Management Timing
Parameter
Description
Notes
Min
T2.3.1
MDC to MDIO (Output) Delay Time
0
T2.3.2
MDIO (Input) to MDC Setup Time
10
T2.3.3
MDIO (Input) to MDC Hold Time
10
T2.3.4
MDC Frequency
Typ
Max
Units
20
ns
ns
ns
2.5
25
MHz
MDC
T2.3.4
T2.3.1
MDIO (output)
MDC
T2.3.2
Valid Data
MDIO (input)
4.8
T2.3.3
AC Specifications — 100 Mb/s MII Transmit Timing
Min
Typ
Max
Units
T2.4.1
Parameter
TX_CLK High/Low Time
Description
100 Mb/s Normal mode
Notes
16
20
24
ns
T2.4.2
TXD[3:0], TX_EN Data Setup to TX_CLK
100 Mb/s Normal mode
10
ns
T2.4.3
TXD[3:0], TX_EN Data Hold from
TX_CLK
100 Mb/s Normal mode
0
ns
T2.4.1
T2.4.1
TX_CL
K
T2.4.2
TXD[3:0
]
TX_EN
4.9
Valid Data
AC Specifications — 100 Mb/s MII Receive Timing
Parameter
Description
(1)
T2.5.1
RX_CLK High/Low Time
T2.5.2
RX_CLK to RXD[3:0], RX_DV, RX_ER
Delay
(1)
T2.4.3
Notes
Min
Typ
Max
Units
100 Mb/s Normal mode
16
20
24
ns
100 Mb/s Normal mode
10
30
ns
RX_CLK may be held low or high for a longer period of time during transition between reference and recovered clocks. Minimum high
and low times will not be violated.
T2.5.1
T2.5.1
RX_CLK
T2.5.2
RXD[3:0]
RX_DV
RX_ER
Valid Data
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
23
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.10 AC Specifications — 100BASE-TX and 100BASE-FX MII Transmit Packet Latency
Timing
Parameter
T2.6.1
(1)
(2)
Description
Notes
TX_CLK to PMD Output Pair
Latency (1) (2)
Min
100BASE-TX and 100BASE-FX modes
IEEE 1588 One-Step Operation enabled
Typ
Max
Units
5
9
bits
bits
For Normal mode, latency is determined by measuring the time from the first rising edge of TX_CLK occurring after the assertion of
TX_EN to the first bit of the “J” code group as output from the PMD Output Pair. 1 bit time = 10 ns in 100 Mb/s mode.
Enabling PHY Control Frames will add latency equal to 8 bits times the PCF_BUF_SIZE setting. For example if PCF_BUF_SIZE is set
to 15, then the additional delay will be 15*8 = 120 bits.
TX_CLK
TX_EN
TXD[3:0]
T2.6.1
PMD Output
Pair
IDLE
(J/K)
DATA
4.11 AC Specifications — 100BASE-TX and 100BASE-FX MII Transmit Packet Deassertion
Timing
Parameter
T2.7.1
(1)
Description
Notes
TX_CLK to PMD Output Pair
Deassertion (1)
Min
100BASE-TX and 100BASE-FX modes
Typ
5
Max
Units
bits
Deassertion is determined by measuring the time from the first rising edge of TX_CLK occurring after the deassertion of TX_EN to the
first bit of the “T” code group as output from the PMD Output Pair. 1 bit time = 10 ns in 100 Mb/s mode.
TX_CLK
TX_EN
TXD[3:0]
T2.7.1
PMD Output
Pair
24
IDLE
(J/K)
Electrical Specifications
DATA
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.12 AC Specifications — 100BASE-TX Transmit Timing (tR/F & Jitter)
Parameter
T2.8.1
Description
100 Mb/s tR and tF Mismatch
T2.8.2
(1)
(2)
Notes
Min
Typ
Max
Units
3
4
5
ns
500
ps
1.4
ns
100 Mb/s PMD Output Pair tR and tF (1)
(2)
100 Mb/s PMD Output Pair Transmit Jitter
Rise and fall times taken at 10% and 90% of the +1 or -1 amplitude.
Normal Mismatch is the difference between the maximum and minimum of all rise and fall times.
T2.8.1
+1 rise
90%
10%
PMD Output Pair
10%
+1 fall
90%
T2.8.1
-1 rise
-1 fall
T2.8.1
T2.8.2
T2.8.1
PMD Output Pair
eye pattern
T2.8.2
4.13 AC Specifications — 100BASE-TX and 100BASE-FX MII Receive Packet Latency
Timing
Parameter
T2.9.1
T2.9.2
(1)
(2)
(3)
(4)
Description
Notes
Carrier Sense ON Delay (1) (2)
Receive Data Latency (3) (4)
Min
Typ
100BASE-TX mode
20
100BASE-FX mode
10
100BASE-TX mode
24
100BASE-FX mode
14
Max
Units
bits
bits
Carrier Sense On Delay is determined by measuring the time from the first bit of the “J” code group to the assertion of Carrier Sense.
1 bit time = 10 ns in 100 Mb/s mode.
Enabling IEEE 1588 Receive Timestamp insertion will increase the Receive Data Latency by 40 bit times.
Enabling PHY Status Frames will introduce variability in Receive Data Latency due to insertion of PHY Status Frames into the receive
datapath.
PMD Input Pair
IDLE
(J/K)
Data
T2.9.1
CRS/CRS_DV
T2.9.2
RXD[3:0]
RX_DV
RX_ER
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
25
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.14 AC Specifications — 100BASE-TX and 100BASE-FX MII Receive Packet Deassertion
Timing
Parameter
T2.10.1
(1)
(2)
Description
Notes
Carrier Sense OFF Delay (1) (2)
Min
Typ
100BASE-TX mode
24
100BASE-FX mode
14
Max
Units
bits
Carrier Sense Off Delay is determined by measuring the time from the first bit of the “T” code group to the deassertion of Carrier Sense
1 bit time = 10 ns in 100 Mb/s mode.
PMD Input Pair
DATA
(T/R)
IDLE
T2.10.1
CRS/CRS_DV
4.15 AC Specifications — 10 Mb/s MII Transmit Timing
Min
Typ
Max
Units
T2.11.1
Parameter
TX_CLK High/Low Time
10 Mb/s MII mode
190
200
210
ns
T2.11.2
TXD[3:0], TX_EN Data Setup to
TX_CLK falling edge (1)
10 Mb/s MII mode
25
ns
T2.11.3
TXD[3:0], TX_EN Data Hold from
TX_CLK rising edge
10 Mb/s MII mode
0
ns
(1)
Description
Notes
An attached Mac should drive the transmit signals using the positive edge of TX_CLK. As shown above, the MII signals are sampled on
the falling edge of TX_CLK.
T2.11.1
T2.11.1
TX_CLK
T2.11.2
TXD[3:0]
TX_EN
T2.11.3
Valid Data
4.16 AC Specifications — 10 Mb/s MII Receive Timing
Min
Typ
Max
Units
T2.12.1
Parameter
RX_CLK High/Low Time (1)
160
200
240
ns
T2.12.2
RXD[3:0], RX_DV transition delay from
10 Mb/s MII mode
RX_CLK rising edge
100
ns
T2.12.3
RX_CLK rising edge delay from
RXD[3:0], RX_DV valid data
100
ns
(1)
Description
Notes
10 Mb/s MII mode
RX_CLK may be held low for a longer period of time during transition between reference and recovered clocks. Minimum high and low
times will not be violated.
T2.12.1
T2.12.1
RX_CLK
T2.12.2
RXD[3:0]
RX_DV
26
T2.12.3
Valid Data
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.17 AC Specifications — 10BASE-T MII Transmit Timing (Start of Packet)
Parameter
T2.13.1
(1)
Description
Notes
Transmit Output Delay from the Falling
Edge of TX_CLK (1)
Min
10 Mb/s MII mode
Typ
Max
Units
3.5
bits
1 bit time = 100 ns in 10 Mb/s.
TX_CLK
TX_EN
TXD[3:0]
PMD Output
Pair
T2.13.1
4.18 AC Specifications — 10BASE-T MII Transmit Timing (End of Packet)
Min
Typ
T2.14.1
Parameter
End of Packet High Time (with '0' ending bit)
Description
Notes
250
300
Max
Units
ns
T2.14.2
End of Packet High Time (with '1' ending bit)
250
300
ns
TX_CLK
TX_EN
PMD Output
Pair
T2.14.1
0
0
T2.14.2
PMD Output
Pair
1
1
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
27
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.19 AC Specifications — 10BASE-T MII Receive Timing (Start of Packet)
Parameter
T2.15.1
Description
Min
Typ
Max
Units
630
1000
ns
(1)
T2.15.2
RX_DV Latency
T2.15.3
Receive Data Latency (2)
(1)
(2)
Notes
Carrier Sense Turn On Delay
(PMD Input Pair to CRS)
10
bits
8
bits
Measurement shown from SFD
10BASE-T RX_DV Latency is measured from first bit of preamble on the wire to the assertion of RX_DV
1 bit time = 100 ns in 10 Mb/s mode.
1st SFD bit decoded
1
0
1
0
1
0
1
0
1
0
1
1
PMD
Input Pair
T2.15.1
CRS/CRS_DV
T2.15.2
RX_DV
T2.15.3
0000
RXD[3:0]
Preamble
SFD
Data
4.20 AC Specifications — 10BASE-T MII Receive Timing (End of Packet)
Parameter
T2.16.1
Description
Notes
Min
Typ
Carrier Sense Turn Off Delay
1
0
1
Max
Units
1.0
µs
IDLE
PMD Input
Pair
RX_CLK
T2.16.1
CRS/CRS_DV
4.21 AC Specifications — 10 Mb/s Heartbeat Timing
Parameter
Description
Notes
Min
Typ
Max
Units
T2.17.1
CD Heartbeat Delay
All 10 Mb/s modes
1200
ns
T2.17.2
CD Heartbeat Duration
All 10 Mb/s modes
1000
ns
TX_EN
TX_CLK
T2.17.1
T2.17.2
COL
28
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.22 AC Specifications — 10 Mb/s Jabber Timing
Parameter
Description
Notes
Min
Typ
Max
Units
T2.18.1
Jabber Activation Time
85
ms
T2.18.2
Jabber Deactivation Time
500
ms
TX_EN
T2.18.1
T2.18.2
PMD Output
Pair
COL
4.23 AC Specifications — 10BASE-T Normal Link Pulse Timing
Parameter
Description
Notes
Min
Typ (1)
Max
Units
T2.19.1
Pulse Width
100
ns
T2.19.2
Pulse Period
16
ms
(1)
These specifications represent transmit timings.
T2.19.2
T2.19.1
Normal Link
Pulse(s)
4.24 AC Specifications — Auto-Negotiation Fast Link Pulse (FLP) Timing
Parameter
Description
Notes
Typ (1)
Min
Max
Units
T2.20.1
Clock, Data Pulse Width
100
ns
T2.20.2
Clock Pulse to Clock Pulse Period
125
µs
T2.20.3
Clock Pulse to Data Pulse Period
62
µs
T2.20.4
Burst Width
2
ms
T2.20.5
FLP Burst to FLP Burst Period
16
ms
(1)
Data = 1
These specifications represent transmit timings.
T.2.20.2
T2.20.3
T2.20.1
T2.20.1
Fast Link
Pulse(s)
clock
pulse
data
pulse
clock
pulse
T2.20.5
T2.20.4
PMD
Output Pair
FLP Burst
FLP Burst
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
29
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.25 AC Specifications — 100BASE-TX Signal Detect Timing
Parameter
T2.21.1
Description
Min
(1)
T2.21.2
SD Internal Turn-off Time
(1)
(2)
Notes
Typ
SD Internal Turn-on Time
Default operation
Fast link-loss indication
enabled (2)
250
1.3
Max
Units
1
ms
300
µs
µs
The signal amplitude on PMD Input Pair must be TP-PMD compliant.
Fast Link-loss detect is enabled by setting the SD_CNFG[8] register bit to a 1.
PMD Input
Pair
T2.21.1
T2.21.2
SD+ internal
4.26 AC Specifications — 100 Mb/s Internal Loopback Timing
Parameter
T2.22.1
(1)
(2)
Description
TX_EN to RX_DV Loopback (1) (2)
Notes
100 Mb/s internal loopback mode
Min
Typ
Max
Units
240
ns
Due to the nature of the descrambler function, all 100BASE-TX Loopback modes will cause an initial “dead-time” of up to 550 µs during
which time no data will be present at the receive MII outputs. The 100BASE-TX timing specified is based on device delays after the
initial 550µs “dead-time”.
Measurement is made from the first rising edge of TX_CLK after assertion of TX_EN.
TX_CLK
TX_EN
TXD[3:0]
CRS/CRS_DV
T2.22.1
RX_CLK
RX_DV
RXD[3:0]
30
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.27 AC Specifications — 10 Mb/s Internal Loopback Timing
Parameter
T2.23.1
(1)
Description
TX_EN to RX_DV Loopback (1)
Notes
Min
Typ
10 Mb/s internal loopback mode
Max
Units
2
µs
Measurement is made from the first falling edge of TX_CLK after assertion of TX_EN.
TX_CLK
TX_EN
TXD[3:0]
CRS/CRS_DV
T2.23.1
RX_CLK
RX_DV
RXD[3:0]
4.28 AC Specifications — RMII Transmit Timing (Slave Mode)
Parameter
Description
Notes
T2.24.1
X1 Clock Period
T2.24.2
TXD[1:0], TX_EN, Data Setup to X1 rising edge
T2.24.3
TXD[1:0], TX_EN, Data Hold from X1 rising edge
T2.24.4
X1 Clock to PMD Output Pair Latency (100 Mb) (1)
(1)
Min
50 MHz Reference Clock
Typ
Max
Units
20
4
ns
2
100BASE-TX or 100BASE-FX
ns
ns
11
bits
Latency measurement is made from the X1 rising edge to the first bit of symbol.
T2.24.1
X1
T2.24.2
TXD[1:0]
TX_EN
T2.24.3
Valid data
T2.24.4
PMD Output
Pair
Symbol
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
31
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.29 AC Specifications — RMII Transmit Timing (Master Mode)
Parameter
Description
Notes
Min
20
Max
Units
RX_CLK, TX_CLK, CLK_OUT Period
T2.25.2
TXD[1:0], TX_EN Data Setup to RX_CLK,
TX_CLK, CLK_OUT rising edge
4
ns
T2.25.3
TXD[1:0], TX_EN Data Hold from RX_CLK,
TX_CLK, CLK_OUT rising edge
2
ns
T2.25.4
RX_CLK, TX_CLK, CLK_OUT to PMD Output Pair From RX_CLK rising edge to
Latency (1)
first bit of symbol
(1)
50 MHz Reference Clock
Typ
T2.25.1
11
ns
bits
Latency measurement is made from the RX_CLK rising edge to the first bit of symbol.
T2.25.1
RX_CLK
TX_CLK
CLK_OUT
T2.25.2
TXD[1:0]
TX_EN
T2.25.3
Valid data
T2.25.4
PMD Output
Pair
32
Symbol
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.30 AC Specifications — RMII Receive Timing (Slave Mode)
Parameter
Description
Notes
T2.26.1
X1 Clock Period
T2.26.2
RXD[1:0], CRS_DV, and RX_ER
output delay from X1 rising
edge (1) (2)
T2.26.3
T2.26.4
T2.26.5
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Min
Typ
50 MHz Reference Clock
CRS ON delay (3)
CRS OFF delay (4)
RXD[1:0] and RX_ER
latency (5) (6) (7)
Max
Units
20
2
ns
14
100BASE-TX mode
18.5
100BASE-FX mode
9
100BASE-TX mode
27
100BASE-FX mode
17
100BASE-TX mode
38
100BASE-FX mode
27
ns
bits
bits
bits
Per the RMII Specification, output delays assume a 25 pF load.
CRS_DV is asserted asynchronously in order to minimize latency of control signals through the PHY. CRS_DV may toggle
synchronously at the end of the packet to indicate CRS de-assertion.
CRS ON delay is measured from the first bit of the JK symbol on the PMD Input Pair to initial assertion of CRS_DV.
CRS OFF delay is measured from the first bit of the TR symbol on the PMD Input Pair to initial de-assertion of CRS_DV.
Receive Latency is measured from the first bit of the symbol pair on the PMD Input Pair. Typical values are with the Elasticity Buffer set
to the default value (01).
Enabling IEEE 1588 Receive Timestamp insertion will increase the Receive Data Latency by 40 bit times.
Enabling PHY Status Frames will introduce variability in Receive Data Latency due to insertion of PHY Status Frames into the receive
datapath.
PMD Input
Pair
IDLE
(J/K)
Data
(TR)
Data
T2.26.4
T2.26.5
X1
T2.26.1
T2.26.3
T2.26.2
CRS/CRS_DV
T2.26.2
RXD[1:0]
RX_ER
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
33
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.31 AC Specifications — RMII Receive Timing (Master Mode)
Parameter
Description
Notes
T2.27.1
RX_CLK, TX_CLK, CLK_OUT
Clock Period
T2.27.2
RXD[1:0], CRS_DV, RX_DV and
RX_ER output delay from
RX_CLK, TX_CLK, CLK_OUT
rising edge (1) (2)
T2.27.3
T2.27.4
T2.27.5
(1)
(2)
(3)
(4)
(5)
CRS ON delay (3)
CRS OFF delay (4)
RXD[1:0] and RX_ER latency (5)
Min
Typ
50 MHz Reference Clock
Max
20
2
ns
14
100BASE-TX mode
18.5
100BASE-FX mode
9
100BASE-TX mode
27
100BASE-FX mode
17
100BASE-TX mode
38
100BASE-FX mode
27
Units
ns
bits
bits
bits
Per the RMII Specification, output delays assume a 25 pF load.
CRS_DV is asserted asynchronously in order to minimize latency of control signals through the PHY. CRS_DV may toggle
synchronously at the end of the packet to indicate CRS de-assertion.
CRS ON delay is measured from the first bit of the JK symbol on the PMD Input Pair to initial assertion of CRS_DV.
CRS OFF delay is measured from the first bit of the TR symbol on the PMD Input Pair to initial de-assertion of CRS_DV.
Receive Latency is measured from the first bit of the symbol pair on the PMD Input Pair. Typical values are with the Elasticity Buffer set
to the default value (01).
PMD Input
Pair
IDLE
(J/K)
Data
(TR)
Data
T2.27.4
T2.27.5
RX_CLK
TX_CLK
CLK_OUT
T2.27.1
T2.27.2
T2.27.2
T2.27.3
T2.27.2
RX_DV
CRS/CRS_DV
T2.27.2
RXD[1:0]
RX_ER
4.32 AC Specifications — RX_CLK Timing (RMII Master Mode)
Parameter
Description
Notes
Min
Typ
Max
Units
T2.28.1
RX_CLK High Time
12
ns
T2.28.2
RX_CLK Low Time
8
ns
T2.28.3
RX_CLK Period (1)
20
ns
(1)
The High Time and Low Time will add up to 20 ns.
T2.28.3
T2.28.1
T2.28.2
RX_CLK
34
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
4.33 AC Specifications — CLK_OUT Timing (RMII Slave Mode)
Parameter
Description
T2.29.1
CLK_OUT High/Low Time
T2.29.2
CLK_OUT propagation delay
Notes
Min
Typ
Max
Units
10
ns
Relative to X1
8
ns
Max
Units
X1
T2.29.2
T2.29.1
T2.29.1
CLK_OUT
4.34 AC Specifications — Single Clock MII (SCMII) Transmit Timing
Parameter
Description
Notes
Min
Typ
T2.30.1
X1 Clock Period
25 MHz Reference Clock
T2.30.2
TXD[3:0], TX_EN Data Setup
To X1 rising edge
4
ns
T2.30.3
TXD[3:0], TX_EN Data Hold
From X1 rising edge
2
ns
T2.30.4
X1 Clock to PMD Output Pair
Latency (100 Mb) (1)
100BASE-TX or 100BASE-FX
(1)
40
13
ns
bits
Latency measurement is made from the X1 rising edge to the first bit of symbol.
T2.30.1
X1
T2.30.2
TXD[3:0]
TX_EN
T2.30.3
Valid data
T2.30.4
PMD Output
Pair
Symbol
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
35
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
4.35 AC Specifications — Single Clock MII (SCMII) Receive Timing
Parameter
Description
Notes
Min
T2.31.1
X1 Clock Period
25 MHz Reference Clock
T2.31.2
RXD[3:0], RX_DV and RX_ER output
delay (1)
From X1 rising edge
T2.31.3
T2.31.4
T2.31.5
(1)
(2)
(3)
(4)
(5)
CRS ON delay (2) (3)
CRS OFF delay (2) (4)
RXD[3:0] and RX_ER latency (5)
Typ
Max
40
2
ns
18
100BASE-TX mode
19
100BASE-FX mode
9
100BASE-TX mode
26
100BASE-FX mode
16
100BASE-TX mode
56
100BASE-FX mode
46
Units
ns
bits
bits
bits
Output delays assume a 25 pF load.
CRS is asserted and de-asserted asynchronously relative to the reference clock.
CRS ON delay is measured from the first bit of the JK symbol on the PMD Input Pair to assertion of CRS_DV.
CRS OFF delay is measured from the first bit of the TR symbol on the PMD Input Pair to de-assertion of CRS_DV.
Receive Latency is measured from the first bit of the symbol pair on the PMD Input Pair. Typical values are with the Elasticity Buffer set
to the default value (01).
PMD Input
Pair
IDLE
(J/K)
Data
(TR)
Data
T2.31.4
T2.31.5
X1
T2.31.1
T2.31.3
CRS/CSR_DV
T2.31.2
T2.31.2
RX_DV
RXD[3:0]
RX_ER
4.36 AC Specifications — 100 Mb/s X1 to TX_CLK Timing
Parameter
T2.32.1
(1)
Description
X1 to TX_CLK delay
(1)
Notes
100 Mb/s Normal mode
Min
0
Typ
Max
Units
5
ns
X1 to TX_CLK timing is provided to support devices that use X1 instead of TX_CLK as the reference for transmit MII data.
X1
T2.32.1
TX_CLK
36
Electrical Specifications
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
5 Configuration
This section includes information on the various configuration options available with the DP83630. The
configuration options described below include:
— Media Configuration
— Auto-Negotiation
— PHY Address and LEDs
— Half Duplex vs. Full Duplex
— Isolate mode
— Loopback mode
— BIST
5.1
MEDIA CONFIGURATION
The DP83630 supports both Twister Pair (100BASE-TX and 10BASE-T) and Fiber (100BASE-FX) media.
The port may be configured for Twisted Pair (TP) or Fiber (FX) operation by strap option or by register
access.
At power-up/reset, the state of the RX_ER pin will select the media for the port. The default selection is
twisted pair mode, while an external pull-down will select FX mode of operation. Strapping the port into FX
mode also automatically sets the Far-End Fault Enable, bit 3 of PCSR (16h), the Scramble Bypass, bit 1
of PCSR (16h) and the Descrambler Bypass, bit 0 of PCSR (16h). In addition, the media selection may be
controlled by writing to bit 6, FX_EN, of PCSR (16h).
5.2
AUTO-NEGOTIATION
The Auto-Negotiation function provides a mechanism for exchanging configuration information between
two ends of a link segment and automatically selecting the highest performance mode of operation
supported by both devices. Fast Link Pulse (FLP) Bursts provide the signalling used to communicate
Auto-Negotiation abilities between two devices at each end of a link segment. For further detail regarding
Auto-Negotiation, refer to Clause 28 of the IEEE 802.3u specification. The DP83630 supports four
different Ethernet protocols (10 Mb/s Half Duplex, 10 Mb/s Full Duplex, 100 Mb/s Half Duplex, and 100
Mb/s Full Duplex), so the inclusion of Auto-Negotiation ensures that the highest performance protocol will
be selected based on the advertised ability of the Link Partner. The Auto-Negotiation function within the
DP83630 can be controlled either by internal register access or by the use of the AN_EN, AN1 and AN0
pins.
5.2.1
Auto-Negotiation Pin Control
The state of AN_EN, AN0 and AN1 determines whether the DP83630 is forced into a specific mode or
Auto-Negotiation will advertise a specific ability (or set of abilities) as given in Table 5-1. These pins allow
configuration options to be selected without requiring internal register access.
The state of AN_EN, AN0 and AN1, upon power-up/reset, determines the state of bits [8:5] of the ANAR
register.
The Auto-Negotiation function selected at power-up or reset can be changed at any time by writing to the
Basic Mode Control Register (BMCR) at address 00h.
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
37
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 5-1. Auto-Negotiation Modes
5.2.2
AN_EN
AN1
AN0
0
0
0
10BASE-T, Half-Duplex
Forced Mode
0
0
1
10BASE-T, Full-Duplex
0
1
0
100BASE-TX, Half-Duplex
100BASE-TX, Full-Duplex
0
1
1
AN_EN
AN1
AN0
1
0
0
10BASE-T, Half/Full-Duplex
1
0
1
100BASE-TX, Half/Full-Duplex
1
1
0
100BASE-TX Full-Duplex
1
1
1
Advertised Mode
10BASE-T, Half/Full-Duplex
100BASE-TX, Half/Full-Duplex
Auto-Negotiation Register Control
When Auto-Negotiation is enabled, the DP83630 transmits the abilities programmed into the AutoNegotiation Advertisement register (ANAR) at address 04h via FLP Bursts. Any combination of 10 Mb/s,
100 Mb/s, Half-Duplex, and Full Duplex modes may be selected.
Auto-Negotiation Priority Resolution:
1. 100BASE-TX Full Duplex (Highest Priority)
2. 100BASE-TX Half Duplex
3. 10BASE-T Full Duplex
4. 10BASE-T Half Duplex (Lowest Priority)
The Basic Mode Control Register (BMCR) at address 00h provides control for enabling, disabling, and
restarting the Auto-Negotiation process. When Auto-Negotiation is disabled, the SPEED SELECTION bit
in the BMCR controls switching between 10 Mb/s or 100 Mb/s operation, and the DUPLEX MODE bit
controls switching between full duplex operation and half duplex operation. The SPEED SELECTION and
DUPLEX MODE bits have no effect on the mode of operation when the Auto-Negotiation Enable bit is set.
The Link Speed can be examined through the PHY Status Register (PHYSTS) at address 10h after a Link
is achieved.
The Basic Mode Status Register (BMSR) indicates the set of available abilities for technology types, AutoNegotiation ability, and Extended Register Capability. These bits are permanently set to indicate the full
functionality of the DP83630 (only the 100BASE-T4 bit is not set since the DP83630 does not support that
function).
The BMSR also provides status on:
• Whether or not Auto-Negotiation is complete
• Whether or not the Link Partner is advertising that a remote fault has occurred
• Whether or not valid link has been established
• Support for Management Frame Preamble suppression
The Auto-Negotiation Advertisement Register (ANAR) indicates the Auto-Negotiation abilities to be
advertised by the DP83630. All available abilities are transmitted by default, but any ability can be
suppressed by writing to the ANAR. Updating the ANAR to suppress an ability is one way for a
management agent to change (restrict) the technology that is used.
The Auto-Negotiation Link Partner Ability Register (ANLPAR) at address 05h is used to receive the base
link code word as well as all next page code words during the negotiation. Furthermore, the ANLPAR will
be updated to either 0081h or 0021h for parallel detection to either 100 Mb/s or 10 Mb/s respectively.
38
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
The Auto-Negotiation Expansion Register (ANER) indicates additional Auto-Negotiation status. The ANER
provides status on:
• Whether or not a Parallel Detect Fault has occurred
• Whether or not the Link Partner supports the Next Page function
• Whether or not the DP83630 supports the Next Page function
• Whether or not the current page being exchanged by Auto-Negotiation has been received
• Whether or not the Link Partner supports Auto-Negotiation
5.2.3
Auto-Negotiation Parallel Detection
The DP83630 supports the Parallel Detection function as defined in the IEEE 802.3u specification. Parallel
Detection requires both the 10 Mb/s and 100 Mb/s receivers to monitor the receive signal and report link
status to the Auto-Negotiation function. Auto-Negotiation uses this information to configure the correct
technology in the event that the Link Partner does not support Auto-Negotiation but is transmitting link
signals that the 100BASE-TX or 10BASE-T PMAs recognize as valid link signals.
If the DP83630 completes Auto-Negotiation as a result of Parallel Detection, bits 5 and 7 within the
ANLPAR register will be set to reflect the mode of operation present in the Link Partner. Note that bits 4:0
of the ANLPAR will also be set to 00001 based on a successful parallel detection to indicate a valid 802.3
selector field. Software may determine that negotiation completed via Parallel Detection by reading a zero
in the Link Partner Auto-Negotiation Able bit once the Auto-Negotiation Complete bit is set. If configured
for parallel detect mode and any condition other than a single good link occurs then the parallel detect
fault bit will be set.
5.2.4
Auto-Negotiation Restart
Once Auto-Negotiation has completed, it may be restarted at any time by setting bit 9 (Restart AutoNegotiation) of the BMCR to one. If the mode configured by a successful Auto-Negotiation loses a valid
link, then the Auto-Negotiation process will resume and attempt to determine the configuration for the link.
This function ensures that a valid configuration is maintained if the cable becomes disconnected.
A renegotiation request from any entity, such as a management agent, will cause the DP83630 to halt any
transmit data and link pulse activity until the break_link_timer expires (~1500 ms). Consequently, the Link
Partner will go into link fail and normal Auto-Negotiation resumes. The DP83630 will resume AutoNegotiation after the break_link_timer has expired by issuing FLP (Fast Link Pulse) bursts.
5.2.5
Enabling Auto-Negotiation via Software
It is important to note that if the DP83630 has been initialized upon power-up as a non-auto-negotiating
device (forced technology), and it is then required that Auto-Negotiation or re-Auto-Negotiation be initiated
via software, bit 12 (Auto-Negotiation Enable) of the Basic Mode Control Register (BMCR) must first be
cleared and then set for any Auto-Negotiation function to take effect.
5.2.6
Auto-Negotiation Complete Time
Parallel detection and Auto-Negotiation take approximately 2-3 seconds to complete. In addition, AutoNegotiation with next page should take approximately 2-3 seconds to complete, depending on the number
of next pages sent.
Refer to Clause 28 of the IEEE 802.3u standard for a full description of the individual timers related to
Auto-Negotiation.
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
39
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
5.3
www.ti.com
AUTO-MDIX
When enabled, this function utilizes Auto-Negotiation to determine the proper configuration for
transmission and reception of data and subsequently selects the appropriate MDI pair for MDI/MDIX
operation. The function uses a random seed to control switching of the crossover circuitry. This
implementation complies with the corresponding IEEE 802.3 Auto-Negotiation and Crossover
Specifications.
Auto-MDIX is enabled by default and can be configured via PHYCR (19h) register, bits [15:14].
Neither Auto-Negotiation nor Auto-MDIX is required to be enabled in forcing crossover of the MDI pairs.
Forced crossover can be achieved through the FORCE_MDIX bit, bit 14 of PHYCR (19h) register.
5.4
AUTO-CROSSOVER IN FORCED MODE
When enabled, this function operates in a manner similar to Auto-MDIX. If no link activity is seen,
switching of the crossover circuitry is based on a random seed. Valid link activity can be link pulses (AutoNegotiation link pulse or 10M link pulses) or 100M signaling. Once valid link activity is seen, crossover will
stop to allow the receive and link functions will proceed normally.
Auto-crossover in forced mode allows for shorter link times because it does not require potentially lengthy
Auto-Negotiation transactions prior to link establishment. Link establishment via Auto-crossover can be
accomplished in full or half duplex configuration, but both sides of the link must be forced to the same
duplex configuration.
Auto-crossover in forced mode is disabled by default and must be configured via PCSR (16h) register, bit
15.
Forced crossover can be achieved while Auto-crossover is enabled through the FORCE_MDIX bit, bit 14
of PHYCR (19h) register.
NOTE: Auto-MDIX and Auto-crossover in forced mode are mutually exclusive and should not be enabled
concurrently. Prior to enabling Auto-crossover in forced mode, Auto-Negotiation and Auto-MDIX should be
disabled.
5.5
PHY ADDRESS
The five PHY address strapping pins are shared with the RXD[3:0] pins and COL pin as shown below.
Table 5-2. PHY Address Mapping
Pin #
PHYAD Function
RXD Function
42
PHYAD0
COL
43
PHYAD1
RXD_3
44
PHYAD2
RXD_2
45
PHYAD3
RXD_1
46
PHYAD4
RXD_0
The DP83630 can be set to respond to any of 32 possible PHY addresses via strap pins. The information
is latched into the PHYCR register (address 19h, bits [4:0]) at device power-up and hardware reset. Each
DP83630 or port sharing an MDIO bus in a system must have a unique physical address.
The DP83630 supports PHY Address strapping values 0 (<00000>) through 31 (<11111>). Strapping
PHY Address 0 puts the part into Isolate Mode. It should also be noted that selecting PHY Address 0
via an MDIO write to PHYCR will not put the device in Isolate Mode. See Mill Isolate Mode for more
information.
For further detail relating to the latch-in timing requirements of the PHY Address pins, as well as the other
hardware configuration pins, refer to the Reset summary in Reset Operation.
40
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Since the PHYAD[0] pin has weak internal pull-up resistor and PHYAD[4:1] pins have weak internal pulldown resistors, the default setting for the PHY address is 00001 (01h).
PHYAD4 = 0
PHYAD3 = 0
PHYAD2 = 0
COL
RXD_3
RXD_2
RXD_0
RXD_1
Refer to Figure 5-1 for an example of a PHYAD connection to external components. In this example, the
PHYAD strapping results in address 00011 (03h).
PHYAD1 = 1
PHYAD0 = 1
2.2 k:
VCC
Figure 5-1. PHYAD Strapping Example
5.5.1
MII Isolate Mode
It is recommended that the user have a basic understanding of Clause 22 of the 802.3u standard.
The DP83630 can be put into MII Isolate Mode by writing a 1 to bit 10 of the BMCR register. Strapping the
PHY Address to 0 will force the device into Isolate Mode when powered up. It should be noted that
selecting Physical Address 0 via an MDIO write to PHYCR will not put the device in the MII isolate mode.
When in the MII Isolate Mode, the DP83630 does not respond to packet data present at TXD[3:0] and
TX_EN inputs and presents a high impedance on the TX_CLK, RX_CLK, RX_DV, RX_ER, RXD[3:0],
COL, and CRS/CRS_DV outputs. When in Isolate Mode, the DP83630 will continue to respond to all serial
management transactions over the MII.
While in Isolate Mode, the PMD output pair will not transmit packet data but will continue to source
100BASE-TX scrambled idles or 10BASE-T normal link pulses.
The DP83630 can Auto-Negotiate or parallel detect to a specific technology depending on the receive
signal at the PMD input pair. A valid link can be established for the receiver even when the DP83630 is in
Isolate Mode.
5.5.2
Broadcast Mode
The DP83630 is also capable of accepting broadcast messages (register writes to PHY address 0x1F).
Setting the BC_WRITE to 1, bit 11 of the PHY Control Register 2 (PHYCR2) at address 0x1C, will
configure the device to accept broadcast messages independent of the local PHY Address value.
5.6
LED INTERFACE
The DP83630 supports three configurable
LED_SPEED/FX_SD, and LED_ACT.
Light
Emitting
Diode
(LED)
pins:
LED_LINK,
Several functions can be multiplexed onto the three LEDs using three different modes of operation. The
LED operation mode can be selected by writing to the LED_CFG[1:0] register bits in the PHY Control
Register (PHYCR) at address 19h, bits [6:5]. LED_CFG[1] is only controllable through register access and
cannot be set by a strap pin.
See Table 5-3 for LED Mode selection.
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
41
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 5-3. LED Mode Selection
Mode
1
LED_CFG[1]
don't care
2
0
3
1
LED_CFG[0]
1
0
0
LED_LINK
LED_SPEED
LED_ACT
ON for Good Link
ON in 100 Mb/s
ON for Activity
OFF for No Link
OFF in 10 Mb/s
OFF for No Activity
ON for Good Link
ON in 100 Mb/s
ON for Collision
BLINK for Activity
OFF in 10 Mb/s
OFF for No Collision
ON for Good Link
ON in 100 Mb/s
ON for Full Duplex
BLINK for Activity
OFF in 10 Mb/s
OFF for Half Duplex
The LED_LINK pin in Mode 1 indicates the link status of the port. In 100BASE-TX mode, link is
established as a result of input receive amplitude compliant with the TP-PMD specifications which will
result in internal generation of signal detect. A 10 Mb/s Link is established as a result of the reception of at
least seven consecutive normal Link Pulses or the reception of a valid 10BASE-T packet. This will cause
the assertion of LED_LINK. LED_LINK will deassert in accordance with the Link Loss Timer as specified
in the IEEE 802.3 specification. In 100BASE-TX mode, an optional fast link loss detection may be enabled
by setting the SD_TIME control in the SD_CNFG register. Enabling fast link loss detection will result in the
LED_LINK deassertion within approximately 1.3 µs of loss of signal on the wire.
The LED_LINK pin in Mode 1 will be OFF when no LINK is present.
The LED_LINK pin in Mode 2 and Mode 3 will be ON to indicate Link is good and BLINK to indicate
activity is present on activity. The BLINK frequency is defined in BLINK_FREQ, bits [7:6] of register
LEDCR (18h).
Activity is defined as configured in LEDACT_RX, bit 8 of register LEDCR (18h). If LEDACT_RX is 0,
Activity is signaled for either transmit or receive. If LEDACT_RX is 1, Activity is only signaled for receive.
The LED_SPEED/FX_SD pin indicates 10 or 100 Mb/s data rate of the port. The standard CMOS driver
goes high when operating in 100 Mb/s operation. The functionality of this LED is independent of mode
selected.
The LED_ACT pin in Mode 1 indicates the presence of either transmit or receive activity. The LED will be
ON for Activity and OFF for No Activity. In Mode 2, this pin indicates the Collision status of the port. The
LED will be ON for Collision and OFF for No Collision.
The LED_ACT pin in Mode 3 indicates Duplex status for 10 Mb/s or 100 Mb/s operation. The LED will be
ON for Full Duplex and OFF for Half Duplex.
In 10 Mb/s half duplex mode, the collision LED is based on the COL signal.
Since these LED pins are also used as strap options, the polarity of the LED is dependent on whether the
pin is pulled up or down.
5.6.1
LEDs
Since the Auto-Negotiation (AN) strap options share the LED output pins, the external components
required for strapping and LED usage must be considered in order to avoid contention.
Specifically, when the LED outputs are used to drive LEDs directly, the active state of each output driver is
dependent on the logic level sampled by the corresponding AN input upon power-up/reset. For example, if
a given AN input is resistively pulled low then the corresponding output will be configured as an active
high driver. Conversely, if a given AN input is resistively pulled high, then the corresponding output will be
configured as an active low driver.
Refer to Figure 5-2 for an example of AN connections to external components. In this example, the AN
strapping results in Auto-Negotiation disabled with 100 Full-Duplex forced.
The adaptive nature of the LED outputs helps to simplify potential implementation issues of these dual
purpose pins.
42
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
LED_ACT
LED_LINK
LED_SPEED
www.ti.com
AN1 = 1
AN0 = 1
165:
165:
165:
VCC
2.2 k:
AN_EN = 0
GND
Figure 5-2. AN Strapping and LED Loading Example
5.6.2
LED Direct Control
The DP83630 provides another option to directly control any or all LED outputs through the LED Direct
Control Register (LEDCR), address 18h. The register does not provide read access to LEDs.
5.7
HALF DUPLEX vs. FULL DUPLEX
The DP83630 supports both half and full duplex operation at both 10 Mb/s and 100 Mb/s speeds.
Half-duplex relies on the CSMA/CD protocol to handle collisions and network access. In Half-Duplex
mode, Carrier Sense (CRS) responds to both transmit and receive activity in order to maintain compliance
with the IEEE 802.3 specification.
Since the DP83630 is designed to support simultaneous transmit and receive activity it is capable of
supporting full-duplex switched applications with a throughput of up to 200 Mb/s when operating in either
100BASE-TX or 100BASE-FX. Because the CSMA/CD protocol does not apply to full-duplex operation,
the DP83630 disables its own internal collision sensing and reporting functions and modifies the behavior
of CRS such that it indicates only receive activity. This allows a full-duplex capable MAC to operate
properly.
All modes of operation (100BASE-TX, 100BASE-FX, 10BASE-T) can run either half-duplex or full-duplex.
Additionally, other than CRS and collision reporting, all remaining MII signaling remains the same
regardless of the selected duplex mode.
It is important to understand that while Auto-Negotiation with the use of Fast Link Pulse code words can
interpret and configure to full-duplex operation, parallel detection can not recognize the difference between
full and half-duplex from a fixed 10 Mb/s or 100 Mb/s link partner over twisted pair. As specified in the
802.3u specification, if a far-end link partner is configured to a forced full-duplex 100BASE-TX ability, the
parallel detection state machine in the partner would be unable to detect the full-duplex capability of the
far-end link partner. This link segment would negotiate to a half-duplex 100BASE-TX configuration (same
scenario for 10 Mb/s).
Auto-Negotiation is not supported in 100BASE-FX operation. Selection of Half or Full-duplex operation is
controlled by bit 8 of the Basic Mode Control Register (BMCR), address 00h. If 100BASE-FX mode is
strapped using the RX_ER pin, the AN0 strap value is used to set the value of bit 8 of the BMCR (00h)
register. Note that the other Auto-Negotiation strap pins (AN_EN and AN1) are ignored in 100BASE-FX
mode.
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
43
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
5.8
www.ti.com
INTERNAL LOOPBACK
The DP83630 includes a Loopback Test mode for facilitating system diagnostics. The Loopback mode is
selected through bit 14 (Loopback) of the Basic Mode Control Register (BMCR). Writing 1 to this bit
enables MII transmit data to be routed to the MII receive outputs. Loopback status may be checked in bit 3
of the PHY Status Register (PHYSTS). While in Loopback mode the data will not be transmitted onto the
media. To ensure that the desired operating mode is maintained, Auto-Negotiation should be disabled
before selecting the Loopback mode.
5.9
POWER DOWN/INTERRUPT
The Power Down and Interrupt functions are multiplexed on pin 7 of the device. By default, this pin
functions as a power down input and the interrupt function is disabled. Setting bit 0 (INT_OE) of MICR
(11h) will configure the pin as an active low interrupt output.
5.9.1
Power Down Control Mode
The PWRDOWN/INTN pin can be asserted low to put the device in a Power Down mode. This is
equivalent to setting bit 11 (POWER DOWN) in the Basic Mode Control Register, BMCR (00h). An
external control signal can be used to drive the pin low, overcoming the weak internal pull-up resistor.
Alternatively, the device can be configured to initialize into a Power Down state by use of an external pulldown resistor on the PWRDOWN/INTN pin. Since the device will still respond to management register
accesses, setting the INT_OE bit in the MICR register will disable the PWRDOWN/INTN input, allowing
the device to exit the Power Down state.
5.9.2
Interrupt Mechanisms
The interrupt function is controlled via register access. All interrupt sources are disabled by default. Setting
bit 1 (INTEN) of MICR (11h) will enable interrupts to be output, dependent on the interrupt mask set in the
lower byte of the MISR (12h). The PWRDOWN/INTN pin is asynchronously asserted low when an
interrupt condition occurs. The source of the interrupt can be determined by reading the upper byte of the
MISR. One or more bits in the MISR will be set, denoting all currently pending interrupts. Reading of the
MISR clears ALL pending interrupts.
Example: To generate an interrupt on a change of link status or on a change of energy detect power state,
the steps would be:
• Write 0003h to MICR to set INTEN and INT_OE
• Write 0060h to MISR to set ED_INT_EN and LINK_INT_EN
• Monitor PWRDOWN/INTN pin
When PWRDOWN/INTN pin asserts low, the user would read the MISR register to see if the ED_INT or
LINK_INT bits are set, i.e. which source caused the interrupt. After reading the MISR, the interrupt bits
should clear and the PWRDOWN/INTN pin will de-assert.
5.10 ENERGY DETECT MODE
When Energy Detect is enabled and there is no activity on the cable, the DP83630 will remain in a low
power mode while monitoring the transmission line. Activity on the line will cause the DP83630 to go
through a normal power up sequence. Regardless of cable activity, the DP83630 will occasionally wake
up the transmitter to put ED pulses on the line, but will otherwise draw as little power as possible. Energy
detect functionality is controlled via register Energy Detect Control (EDCR), address 1Dh.
44
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
5.11 LINK DIAGNOSTIC CAPABILITIES
The DP83630 contains several system diagnostic capabilities for evaluating link quality and detecting
potential cabling faults in twisted pair cabling. Software configuration is available through the Link
Diagnostics Registers - Page 2 which can be selected via Page Select Register (PAGESEL), address 13h.
These capabilities include:
— Linked Cable Status
— Link Quality Monitor
— TDR (Time Domain Reflectometry) Cable Diagnostics
5.11.1 Linked Cable Status
In an active connection with a valid link status, the following diagnostic capabilities are available:
— Polarity reversal
— Cable swap (MDI vs MDIX) detection
— 100 Mb Cable Length Estimation
— Frequency offset relative to link partner
— Cable Signal Quality Estimation
5.11.1.1 Polarity Reversal
The DP83630 detects polarity reversal by detecting negative link pulses. The Polarity indication is
available in bit 12 of the PHYSTS (10h) or bit 4 of the 10BTSCR (1Ah). Inverted polarity indicates the
positive and negative conductors in the receive pair are swapped. Since polarity is corrected by the
receiver, this does not necessarily indicate a functional problem in the cable.
Since the polarity indication is dependent on link pulses from the link partner, polarity indication is only
valid in 10 Mb modes of operation, or in 100 Mb Auto-Negotiated mode. Polarity indication is not available
in 100 Mb forced mode of operation or in a parallel detected 100 Mb mode.
5.11.1.2 Cable Swap Indication
As part of Auto-Negotiation, the DP83630 has the ability (using Auto-MDIX) to automatically detect a cable
with swapped MDI pairs and select the appropriate pairs for transmitting and receiving data. Normal
operation is termed MDI, while crossed operation is MDIX. The MDIX status can be read from bit 14 of the
PHYSTS (10h).
5.11.1.3 100 Mb Cable Length Estimation
The DP83630 provides a method of estimating cable length based on electrical characteristics of the 100
Mb link. This essentially provides an effective cable length rather than a measurement of the physical
cable length. The cable length estimation is only available in 100 Mb mode of operation with a valid link
status. The cable length estimation is available at the Link Diagnostics Registers - Page 2, register 100
Mb Length Detect (LEN100_DET), address 14h.
5.11.1.4 Frequency Offset Relative to Link Partner
As part of the 100 Mb clock recovery process, the DSP implementation provides a frequency control
parameter. This value may be used to indicate the frequency offset of the device relative to the link
partner. This operation is only available in 100 Mb operation with a valid link status. The frequency offset
can be determined using the register 100 Mb Frequency Offset Indication (FREQ100), address 15h, of the
Link Diagnostics Registers - Page 2.
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
45
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Two different versions of the Frequency Offset may be monitored through bits [7:0] of register FREQ100
(15h). The first is the long-term Frequency Offset. The second is the current Frequency Control value,
which includes short-term phase adjustments and can provide information on the amount of jitter in the
system.
5.11.1.5 Cable Signal Quality Estimation
The cable signal quality estimator keeps a simple tracking of results of the DSP and can be used to
generate an approximate Signal-to-Noise Ratio for the 100 Mb receiver. This information is available to
software through the Link Diagnostics Registers - Page 2: Variance Control Register (VAR_CTRL),
address 1Ah and Variance Data Register (VAR_DATA), address 1Bh.
The variance computation times (VAR_TIMER) can be chosen from the set of {2, 4, 6, 8} ms. The 32-bit
variance sum can be read by two consecutive reads of the VAR_DATA register. This sum can be used to
compute an SNR estimate by software using the following equation:
SNR = 10log10((37748736 * VAR_TIMER) / Variance)
(1)
5.11.2 Link Quality Monitor
The Link Quality Monitor allows a method to generate an alarm when the DSP adaption strays from a
programmable window. This could occur due to changes in the cable which could indicate a potential
problem. Software can program thresholds for the following DSP parameters to be used to interrupt the
system:
— Digital Equalizer C1 Coefficient (DEQ C1)
— Digital Adaptive Gain Control (DAGC)
— Digital Base-Line Wander Control (DBLW)
— Recovered Clock Long-Term Frequency Offset (FREQ)
— Recovered Clock Frequency Control (FC)
— Signal-to-Noise Ratio (SNR) Variance
Software is expected to read initial adapted values and then program the thresholds based on an
expected valid range. This mechanism takes advantage of the fact that the DSP adaptation should remain
in a relatively small range once a valid link has been established.
5.11.2.1 Link Quality Monitor Control and Status
Control of the Link Quality Monitor is done through the Link Quality Monitor Register (LQMR), address
1Dh and the Link Quality Data Register (LQDR), address 1Bh of the Link Diagnostics Registers - Page 2.
The LQMR register includes a global enable to enable the Link Quality Monitor function. In addition, it
provides warning status from both high and low thresholds for each of the monitored parameters except
SNR Variance.. The LQMR2 register provides warning status for the high threshold of SNR Variance
(upper 16 bits); there is no low threshold. Note that individual low or high parameter threshold
comparisons can be disabled by setting to the minimum or maximum values.
To allow the Link Quality Monitor to interrupt the system, the Interrupt must be enabled through the
interrupt control registers, MICR (11h) and MISR (12h).
The Link Quality Monitor may also be used to automatically reset the DSP and restart adaption. Separate
enable bits in LQMR and LQMR2 allow for automatic reset based on each of the parameter values. If
enabled, a violation of one of the thresholds will result in a restart of the DSP adaption. In addition if the
PCSR:SD_OPTION register bit is set to 0, the violation will also result in a drop in Link Status.
46
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
5.11.2.2 Checking Current Parameter Values
Prior to setting Threshold values, it is recommended that software check current adapted values. The
thresholds may then be set relative to the adapted values. The current adapted values can be read using
the LQDR register by setting the SAMPLE_PARAM bit [13] of LQDR, address (1Eh).
For example, to read the DBLW current value:
1. Write 2400h to LQDR (1Eh) to set the SAMPLE_PARAM bit and set the LQ_PARAM_SEL[2:0] to 010.
2. Read LQDR (1Eh). Current DBLW value is returned in the low 8 bits.
5.11.2.3 Threshold Control
The LQDR (1Eh) register also provides a method of programming high and low thresholds for each of the
five parameters that can be monitored. The register implements an indirect read/write mechanism.
Writes are accomplished by writing data, address, and a write strobe to the register. Reads are
accomplished by writing the address to the register, and reading back the value of the selected threshold.
Setting thresholds to the maximum or minimum values will disable the threshold comparison since values
have to exceed the threshold to generate a warning condition.
Warnings are not generated if the parameter is equal to the threshold. By default, all thresholds are
disabled by setting to the minimum or maximum values. The Table 5-4 shows the five parameters and
range of values:
Table 5-4. Link Quality Monitor Parameter Ranges
Parameter
Minimum Value
Maximum Value
Min (2-s comp)
-128
+127
0x80
0x7F
DAGC
0
+255
0x00
0xFF
DBLW
-128
+127
0x80
0x7F
Frequency Offset
-128
+127
0x80
0x7F
Frequency Control
-128
+127
0x80
0x7F
0
+2304
0x0000
0x900
DEQ_C1
SNR Variance
Max (2-s comp)
Note that values are signed 2-s complement values except for DAGC and Variance which are always
positive. The maximum SNR Variance is calculated by assuming the worst-case squared error (144) is
accumulated every 8 ns for 8*220 ns (roughly 8 ms or exactly 1,048,576 clock cycles).
For example, to set the DBLW Low threshold to -38:
1. Write 14DAh to LQDR to set the Write_LQ_Thr bit, select the DBLW Low Threshold, and write data of
-38 (0xDA).
2. Write 8000 to LQMR to enable the Link Quality Monitor (if not already enabled).
5.11.3 TDR Cable Diagnostics
The DP83630 implements a Time Domain Reflectometry (TDR) method of cable length measurement and
evaluation which can be used to evaluate a connected twisted pair cable. The TDR implementation
involves sending a pulse out on either the Transmit or Receive conductor pair and observing the results
on either pair. By observing the types and strength of reflections on each pair, software can determine the
following:
— Cable short
— Cable open
— Distance to fault
— Identify which pair has a fault
— Pair skew
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
47
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
The TDR cable diagnostics works best in certain conditions. For example, an unterminated cable provides
a good reflection for measuring cable length, while a cable with an ideal termination to an unpowered
partner may provide no reflection at all.
5.11.4 TDR Pulse Generator
The TDR implementation can send two types of TDR pulses. The first option is to send 50 ns or 100 ns
link pulses from the 10 Mb Common Driver. The second option is to send pulses from the 100 Mb
Common Driver in 8 ns increments up to 56 ns in width. The 100 Mb pulses will alternate between positive
and negative pulses. The shorter pulses provide better ability to measure short cable lengths, especially
since they will limit overlap between the transmitted pulse and a reflected pulse. The longer pulses may
provide better measurements of long cable lengths.
In addition, if the pulse width is programmed to 0, no pulse will be sent, but the monitor circuit will still be
activated. This allows sampling of background data to provide a baseline for analysis.
5.11.5 TDR Pulse Monitor
The TDR function monitors data from the Analog to Digital Converter (ADC) to detect both peak values
and values above a programmable threshold. It can be programmed to detect maximum or minimum
values. In addition, it records the time, in 8 ns intervals, at which the peak or threshold value first occurs.
The TDR monitor implements a timer that starts when the pulse is transmitted. A window may be enabled
to qualify incoming data to look for response only in a desired range. This is especially useful for
eliminating the transmitted pulse, but also may be used to look for multiple reflections.
5.11.6 TDR Control Interface
The TDR Control Interface is implemented in the Link Diagnostics Registers - Page 2 through TDR
Control (TDR_CTRL), address 16h and TDR Window (TDR_WIN), address 17h. The following basic
controls are:
• TDR Enable: Enable bit 15 of TDR_CTRL (16h) to allow the TDR function. This bypasses normal
operation and gives control of the CD10 and CD100 block to the TDR function.
• TDR Send Pulse: Enable bit 11 of TDR_CTRL (16h) to send the TDR pulse and starts the TDR
Monitor
The following transmit mode controls are available:
• Transmit Mode: Enables use of 10 Mb Link pulses from the 10 Mb Common Driver or data pulses
from the 100 Mb Common Driver by enabling TDR_100 Mb, bit 14 of TDR_CRTL (16h).
• Transmit Pulse Width: Bits [10:8] of TDR_CTRL (16h) allows sending of 0 to 7 clock width pulses.
Actual pulses are dependent on the transmit mode. If the pulse width is set to 0, then no pulse will be
sent.
• Transmit Channel Select: The transmitter can send pulses down either the transmit pair or the
receive pair by enabling bit 13 of TDR_CTRL (16h). Default value is to select the transmit pair.
The following receive mode controls are available:
• Min/Max Mode Control: Bit 7 of TDR_CTRL (16h) controls the TDR Monitor operation. In default
mode, the monitor will detect maximum (positive) values. In Min Mode, the monitor will detect minimum
(negative) values.
• Receive Channel Select: The receiver can monitor either the transmit pair or the receive pair by
enabling bit 12 of TDR_CTRL (16h). Default value is to select the transmit pair.
• Receive Window: The receiver can monitor receive data within a programmable window using the
TDR Window Register (TDR_WIN), address 17h. The window is controlled by two register values: TDR
Start Window, bits [15:8] of TDR_WIN (17h) and TDR Stop Window, bits [7:0] of TDR_WIN (17h). The
TDR Start Window indicates the first clock to start sampling. The TDR Stop Window indicates the last
clock to sample. By default, the full window is enabled, with Start set to 0 and Stop set to 255. The
window range is in 8 ns clock increments, so the maximum window size is 2048 ns.
48
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
5.11.7 TDR Results
The results of a TDR peak and threshold measurement are available in the TDR Peak Measurement
Register (TDR_PEAK), address 18h and TDR Threshold Measurement Register (TDR_THR), address
19h. The threshold measurement may be a more accurate method of measuring the length of longer
cables since it provides a better indication of the start of the received pulse, rather than the peak value.
Software utilizing the TDR function should implement an algorithm to send TDR pulses and evaluate
results. Multiple runs should be used to best qualify any received pulses as multiple reflections could exist.
In addition, when monitoring the transmitting pair, the window feature should be used to disqualify the
transmitted pulse. Multiple runs may also be used to average the values providing more accurate results.
Actual distance measurements are dependent on the velocity of propagation of the cable. The delay value
is typically on the order of 4.6 to 4.9 ns/m.
5.12 BIST
The DP83630 incorporates an internal Built-in Self Test (BIST) circuit to accommodate in-circuit testing or
diagnostics. The BIST circuit can be utilized to test the integrity of the transmit and receive data paths.
BIST testing can be performed with the part in the internal loopback mode or externally looped back using
a loopback cable fixture. BIST testing can also be performed between two directly connected DP83630
devices.
The BIST is implemented with independent transmit and receive paths, with the transmit block generating
a continuous stream of a pseudo random sequence. The user can select a 9 bit or 15 bit pseudo random
sequence from the PSR_15 bit in the PHY Control Register (PHYCR). The received data is compared to
the generated pseudo-random data by the BIST Linear Feedback Shift Register (LFSR) to determine the
BIST pass/fail status.
The pass/fail status of the BIST is stored in the BIST status bit in the PHYCR register. The status bit
defaults to 0 (BIST fail) and will transition on a successful comparison. If an error (mis-compare) occurs,
the status bit is latched and is cleared upon a subsequent write to the Start/Stop bit.
For transmit VOD testing, the Packet BIST Continuous Mode can be used to allow continuous data
transmission by setting the BIST_CONT_MODE, bit 5, of CDCTRL1 (1Bh).
The number of BIST errors can be monitored through the BIST Error Count in the CDCTRL1 (1Bh), bits
[15:8].
Configuration
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
49
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
6 MAC Interface
The DP83630 supports several modes of operation using the MII interface pins. The options are defined in
the following sections and include:
— MII Mode
— RMII Mode
— Single Clock MII Mode (SCMII)
In addition, the DP83630 supports the standard 802.3u MII Serial Management Interface.
The modes of operation can be selected by strap options or register control. For RMII Slave mode, it is
recommended to use the strap option since it requires a 50 MHz clock instead of the normal 25 MHz.
In each of these modes, the IEEE 802.3 serial management interface is operational for device
configuration and status. The serial management interface of the MII allows for the configuration and
control of multiple PHY devices, gathering of status, error information, and the determination of the type
and capabilities of the attached PHY(s).
6.1
MII INTERFACE
The DP83630 incorporates the Media Independent Interface (MII) as specified in Clause 22 of the IEEE
802.3u standard. This interface may be used to connect PHY devices to a MAC in 10/100 Mb/s systems.
This section describes the nibble wide MII data interface.
The nibble wide MII data interface consists of a receive bus and a transmit bus each with control signals
to facilitate data transfer between the PHY and the upper layer (MAC).
6.1.1
Nibble-wide MII Data Interface
Clause 22 of the IEEE 802.3u specification defines the Media Independent Interface. This interface
includes a dedicated receive bus and a dedicated transmit bus. These two data buses, along with various
control and status signals, allow for the simultaneous exchange of data between the DP83630 and the
upper layer agent (MAC).
The receive interface consists of a nibble wide data bus RXD[3:0], a receive error signal RX_ER, a receive
data valid flag RX_DV, and a receive clock RX_CLK for synchronous transfer of the data. The receive
clock operates at either 2.5 MHz to support 10 Mb/s operation modes or at 25 MHz to support 100 Mb/s
operational modes.
The transmit interface consists of a nibble wide data bus TXD[3:0], a transmit enable control signal
TX_EN, and a transmit clock TX_CLK which runs at either 2.5 MHz or 25 MHz.
Additionally, the MII includes the carrier sense signal CRS, as well as a collision detect signal COL. The
CRS signal asserts to indicate the reception of data from the network or as a function of transmit data in
Half Duplex mode. The COL signal asserts as an indication of a collision which can occur during halfduplex operation when both a transmit and receive operation occur simultaneously.
6.1.2
Collision Detect
For Half Duplex, a 10BASE-T or 100BASE-TX collision is detected when the receive and transmit
channels are active simultaneously. Collisions are reported by the COL signal on the MII.
If the DP83630 is transmitting in 10 Mb/s mode when a collision is detected, the collision is not reported
until seven bits have been received while in the collision state. This prevents a collision being reported
incorrectly due to noise on the network. The COL signal remains set for the duration of the collision.
If a collision occurs during a receive operation, it is immediately reported by the COL signal.
50
MAC Interface
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
When heartbeat is enabled (only applicable to 10 Mb/s operation), approximately 1µs after the
transmission of each packet, a Signal Quality Error (SQE) signal of approximately 10 bit times is
generated (internally) to indicate successful transmission. SQE is reported as a pulse on the COL signal of
the MII.
Collision is not indicated during Full Duplex operation.
6.1.3
Carrier Sense
In 10 Mb/s operation, Carrier Sense (CRS) is asserted due to receive activity once valid data is detected
via the Smart Squelch function. During 100 Mb/s operation CRS is asserted when a valid link (SD) and
two non-contiguous zeros are detected on the line.
For 10 or 100 Mb/s Half Duplex operation, CRS is asserted during either packet transmission or reception.
For 10 or 100 Mb/s Full Duplex operation, CRS is asserted only due to receive activity.
CRS is deasserted following an end of packet.
6.2
REDUCED MII INTERFACE
The DP83630 incorporates the Reduced Media Independent Interface (RMII) as specified in the RMII
specification (rev 1.2) from the RMII Consortium. This interface may be used to connect PHY devices to a
MAC in 10/100 Mb/s systems using a reduced number of pins. In this mode, data is transferred 2-bits at a
time using the 50 MHz RMII_REF clock for both transmit and receive. The following pins are used in RMII
mode:
— TX_EN
— TXD[1:0]
— RX_ER (optional for MAC)
— CRS/CRS_DV
— RXD[1:0]
— X1 (25 MHz in RMII Master mode, 50 MHz in RMII Slave mode)
— RX_CLK, TX_CLK, CLK_OUT (50 MHz RMII reference clock in RMII Master mode only)
In addition, the RMII mode supplies an RX_DV signal which allows for a simpler method of recovering
receive data without having to separate RX_DV from the CRS_DV indication. This is especially useful for
systems which do not require CRS, such as systems that only support full-duplex operation. This signal is
also useful for diagnostic testing where it may be desirable to loop external Receive RMII data directly to
the transmitter.
The RX_ER output may be used by the MAC to detect error conditions. It is asserted for symbol errors
received during a packet, False Carrier events, and also for FIFO underrun or overrun conditions. Since
the PHY is required to corrupt receive data on an error, a MAC is not required to use RX_ER.
Since the reference clock operates at 10 times the data rate for 10 Mb/s operation, transmit data is
sampled every 10 clocks. Likewise, receive data will be generated every 10th clock so that an attached
device can sample the data every 10 clocks.
RMII Slave mode requires a 50 MHz oscillator to be connected to the device X1 pin. A 50 MHz crystal is
not supported. RMII Master mode can use either a 25 MHz oscillator connected to X1 or a 25 MHz crystal
connected to X1 and X2.
To tolerate potential frequency differences between the 50 MHz reference clock and the recovered receive
clock, the receive RMII function includes a programmable elasticity buffer. The elasticity buffer is
programmable to minimize propagation delay based on expected packet size and clock accuracy. This
allows for supporting a range of packet sizes including jumbo frames.
MAC Interface
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
51
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
The elasticity buffer will force Frame Check Sequence errors for packets which overrun or underrun the
FIFO. Underrun and overrun conditions can be reported in the RMII and Bypass Register (RBR). Table 61 indicates how to program the elasticity buffer FIFO (in 4-bit increments) based on expected maximum
packet size and clock accuracy. It assumes both clocks (RMII Reference clock and far-end Transmitter
clock) have the same accuracy.
Packet lengths can be scaled linearly based on accuracy (+/- 25 ppm would allow packets twice as large).
If the threshold setting must support both 10 Mb and 100 Mb operation, the setting should be made to
support both speeds.
Table 6-1. Supported Packet Sizes at +/-50 ppm Frequency Accuracy
Start Threshold RBR[1:0]
6.2.1
Latency Tolerance
Recommended Packet Size at +/- 50 ppm
100 Mb
10 Mb
100 Mb
10 Mb
01 (default)
2 bits
8 bits
2,400 bytes
9,600 bytes
10
6 bits
4 bits
7,200 bytes
4,800 bytes
11
10 bits
8 bits
12,000 bytes
9,600 bytes
00
14 bits
12 bits
16,800 bytes
14,400 bytes
RMII Master Mode
In RMII Master Mode, the DP83630 uses a 25 MHz crystal on X1/X2 and internally generates the 50 MHz
RMII reference clock for use by the RMII logic. The 50 MHz clock is output on RX_CLK, TX_CLK, and
CLK_OUT for use as the reference clock for an attached MAC. RX_CLK operates at 25 MHz during reset.
6.2.2
RMII Slave Mode
In RMII Slave Mode, the DP83630 takes a 50 MHz reference clock input on X1 from an external oscillator
or another DP83630 in RMII Master Mode. The 50 MHz is internally divided down to 25 MHz for use as
the reference clock for non-RMII logic. RX_CLK, TX_CLK, and CLK_OUT should not be used as the RMII
reference clock in this mode but may be used for other system devices.
6.3
SINGLE CLOCK MII MODE
Single Clock MII (SCMII) Mode allows MII operation using a single 25 MHz reference clock. Normal MII
Mode requires three clocks, a reference clock for physical layer functions, a transmit MII clock, and a
receive MII clock. Similar to RMII mode, Single Clock MII mode requires only the reference clock. In
addition to reducing the number of pins required, this mode allows the attached MAC device to use only
the reference clock domain. AC Timing requirements for SCMII operation are similar to the RMII timing
requirements.
For 10 Mb operation, as in RMII mode, data is sampled and driven every 10 clocks since the reference
clock is at 10 times the data rate.
Separate control bits allow enabling the Transmit and Receive Single Clock modes separately, allowing
just transmit or receive to operate in this mode. Control of Single Clock MII mode is through the RBR
register.
Single Clock MII mode incorporates the use of the RMII elasticity buffer, which is required to tolerate
potential frequency differences between the 25 MHz reference clock and the recovered receive clock.
Settings for the elasticity buffer for SCMII mode are detailed in Table 6-2.
52
MAC Interface
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 6-2. Supported SCMII Packet Sizes at +/-50 ppm Frequency Accuracy
Start Threshold RBR[1:0]
6.4
6.4.1
Latency Tolerance
Recommended Packet Size at +/- 50 ppm
100 Mb
10 Mb
100 Mb
10 Mb
01 (default)
4 bits
8 bits
4,000 bytes
9,600 bytes
10
4 bits
8 bits
4,000 bytes
9,600 bytes
11
8 bits
8 bits
9,600 bytes
9,600 bytes
00
8 bits
8 bits
9,600 bytes
9,600 bytes
IEEE 802.3u MII SERIAL MANAGEMENT INTERFACE
Serial Management Register Access
The serial management MII specification defines a set of thirty-two 16-bit status and control registers that
are accessible through the management interface pins MDC and MDIO. The DP83630 implements all the
required MII registers as well as several optional registers. These registers are fully described in Register
Block. A description of the serial management access protocol follows.
6.4.2
Serial Management Access Protocol
The serial control interface consists of two pins, Management Data Clock (MDC) and Management Data
Input/Output (MDIO). MDC has a maximum clock rate of 25 MHz and no minimum rate. The MDIO line is
bi-directional and may be shared by up to 32 devices. The MDIO frame format is shown below in Table 63.
Table 6-3. Typical MDIO Frame Format
MII Management Serial Protocol
<idle><start><opcode><device addr><reg addr><turnaround><data><idle>
Read Operation
<idle><01><10><AAAAA><RRRRR><Z0><xxxx xxxx xxxx xxxx><idle>
Write Operation
<idle><01><01><AAAAA><RRRRR><10><xxxx xxxx xxxx xxxx><idle>
The MDIO pin requires a pull-up resistor (1.5 kΩ) which, during IDLE and turnaround, will pull MDIO high.
The DP83630 also includes an option to enable an internal pull-up on the MDIO pin, MDIO_PULL_EN bit
in the CDCTRL1 register. In order to initialize the MDIO interface, the station management entity sends a
sequence of 32 contiguous logic ones on MDIO to provide the DP83630 with a sequence that can be used
to establish synchronization. This preamble may be generated either by driving MDIO high for 32
consecutive MDC clock cycles, or by simply allowing the MDIO pull-up resistor to pull the MDIO pin high
during which time 32 MDC clock cycles are provided. In addition 32 MDC clock cycles should be used to
re-sync the device if an invalid Start, Opcode, or turnaround bit is detected.
The DP83630 waits until it has received this preamble sequence before responding to any other
transaction. Once the DP83630 serial management port has been initialized no further preamble
sequencing is required until after a power-on/reset, invalid Start, invalid Opcode, or invalid turnaround (TA)
bit has occurred.
MAC Interface
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
53
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
The Start code is indicated by a <01> pattern. This assures the MDIO line transitions from the default idle
line state.
Turnaround is defined as an idle bit time inserted between the Register Address field and the Data field.
To avoid contention during a read transaction, no device shall actively drive the MDIO signal during the
first bit of Turnaround. The addressed DP83630 drives the MDIO with a zero for the second bit of
turnaround and follows this with the required data. Figure 6-1 shows the timing relationship between MDC
and the MDIO as driven/received by the Station (STA) and the DP83630 (PHY) for a typical register read
access.
For write transactions, the station management entity writes data to the addressed DP83630 thus
eliminating the requirement for MDIO Turnaround. The Turnaround time is filled by the management entity
by inserting <10>. Figure 7-1 shows the timing relationship for a typical MII register write access.
MDC
z
MDIO
(STA)
z
z
z
MDIO
(PHY)
z
0
Idle
1
1
0
0
1
1
0
0
0
Start Opcode PHY Address
(Read) (PHY AD = 0Ch)
0
0
0
0 z 0
Register Address
(00h = BCMR)
0
0
1
1
0
0
TA
0
1
0
0
0
0
0
0
0
z
0
Register Data
Idle
Figure 6-1. Typical MDC/MDIO Read Operation
MDC
MDIO
(STA)
z
z
z
Idle
0
1
0
1
0
1
1
0
0
Start Opcode
PHY Address
(Write) (PHY AD = 0Ch)
0
0
0
0
0
Register Address
(00h = BCMR)
1
0
0
0
0
0
0
TA
0
0
0
0
0
Register Data
0
0
0
0
0
0
z
Idle
Figure 6-2. Typical MDC/MDIO Write Operation
6.4.3
Serial Management Preamble Suppression
The DP83630 supports a Preamble Suppression mode as indicated by a one in bit 6 of the Basic Mode
Status Register (BMSR, address 01h.) If the station management entity (i.e. MAC or other management
controller) determines that all PHYs in the system support Preamble Suppression by returning a one in
this bit, then the station management entity need not generate preamble for each management
transaction.
The DP83630 requires a single initialization sequence of 32 bits of preamble following hardware/software
reset. This requirement is generally met by the mandatory pull-up resistor on MDIO in conjunction with a
continuous MDC, or the management access made to determine whether Preamble Suppression is
supported.
While the DP83630 requires an initial preamble sequence of 32 bits for management initialization, it does
not require a full 32-bit sequence between each subsequent transaction. A minimum of one idle bit
between management transactions is required as specified in the IEEE 802.3u specification.
6.5
PHY CONTROL FRAMES
The DP83630 supports a packet-based control mechanism for use in situations where the Serial
Management Interface is not available or does not provide enough throughput. Application software may
build a packet, called a PHY Control Frame (PCF), to be passed to the PHY through the MAC Transmit
Data interface. The PHY will intercept these packets and use them to assert writes to Management
Registers as if they occurred via the Management Interface. Multiple register writes may be incorporated
in a single frame.
54
MAC Interface
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
The PHY Control Frame may also be used to read a register location. The read value will be returned in a
PHY Status Frame if that function is enabled. Only a single read may be outstanding at any time, so only
one read should be included in a single PHY Control Frame.
The PHY Control Frame block performs the following functions:
• Parse incoming transmit packets to detect PHY Control Frames
• Truncate PHY Control Frames to prevent complete frame from reaching the transmit physical medium
• Buffer up to 15 bytes of the Frame to be intercepted by the PHY with no portion reaching physical
medium
• Detect commands in the PHY Control Frame and pass them to the register block
• Check CRC to detect error conditions
• Report CRC and invalid command errors to the system via register status and/or interrupt
PHY Control Frames can be enabled through the PCF_Enable bit in the PHY Control Frames
Configuration Register (PCFCR). PHY Control Frames can also be enabled by using the PCF_EN strap
option. For a more detailed discussion on the use of PHY Control Frames, refer to the Software
Development Guide for the DP83630.
6.6
PHY STATUS FRAMES
The DP83630 implements a packet-based status mechanism that allows the PHY to queue up events and
pass them to the microcontroller through the receive data interface. The packet, called a PHY Status
Frame, may be used to provide IEEE 1588 status for transmit packet timestamps, receive packet
timestamps, event timestamps, and trigger conditions. In addition the device can generate status
messages indicating packet buffering errors and to return data read using the PHY Control Frame register
access mechanism.
Each PHY Status Frame may include multiple status messages. The packet will be framed such that it will
look like a IEEE 1588 frame to ensure that it will get to the IEEE 1588 software stack. The PHY will
provide buffering of any incoming packet to allow the status packet to be passed to the MAC.
Programmable inter-frame gap and preamble length allow the PHY to recover lost bandwidth in the case
of heavy receive traffic.
In a PHY Status Frame, status messages are not provided in a chronological order. Instead, they are
provided in the following order of priority:
1. PHY Control Frame Read Data
2. Packet Buffer Error
3. Transmit Timestamp
4. Receive Timestamp
5. Trigger Status
6. Event Timestamp
Each of the message types may be individually enabled, allowing options on which functions may be
delivered in a PHY Status Frame.
Timestamps that are delivered via PHY Status Frames will not be reflected in the corresponding status
and timestamp registers nor will they generate an interrupt.
The packet format may be configured to look like a Layer 2 Ethernet frame or a UDP/IPv4 frame.
For a more detailed discussion on the use of PHY Status Frames, refer to the Software Development
Guide for the DP83630.
MAC Interface
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
55
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
7 Architecture
This section describes the operations within each transceiver module, 100BASE-TX and 10BASE-T. Each
operation consists of several functional blocks and is described in the following:
— 100BASE-TX Transmitter
— 100BASE-TX Receiver
— 100BASE-FX Operation
— 10BASE-T Transceiver Module
7.1
100BASE-TX TRANSMITTER
The 100BASE-TX transmitter consists of several functional blocks which convert synchronous 4-bit nibble
data, as provided by the MII, to a scrambled MLT-3 125 Mb/s serial data stream. Because the 100BASETX TP-PMD is integrated, the differential output pins, PMD Output Pair, can be directly routed to the
magnetics.
The block diagram in Figure 7-1 provides an overview of each functional block within the 100BASE-TX
transmit section.
The Transmitter section consists of the following functional blocks:
— Code-Group Encoder and Injection block
— Scrambler block (bypass option)
— NRZ to NRZI Encoder block
— Binary to MLT-3 Converter / Common Driver block
The bypass option for the functional blocks within the 100BASE-TX transmitter provides flexibility for
applications where data conversion is not always required. The DP83630 implements the 100BASE-TX
transmit state machine diagram as specified in the IEEE 802.3u Standard, Clause 24.
56
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
TX_CLK
DIVIDE
BY 5
TXD[3:0]/
TX_EN
4B5B CODEGROUP
ENCODER and
INJECTOR
5B PARALLEL
TO SERIAL
125 MHz CLOCK
SCRAMBLER
MUX
BP_SCR
100BASE-TX
LOOPBACK
MLT[1:0]
NRZ TO NRZI
ENCODER
BINARY
TO MLT-3/
COMMON
DRIVER
PMD OUTPUT PAIR
Figure 7-1. 100BASE-TX Transmit Block Diagram
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
57
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 7-1. 4B5B Code-Group Encoding/Decoding
Name
PCS 5B Code-Group
MII 4B Nibble Code
0
11110
0000
1
01001
0001
2
10100
0010
3
10101
0011
4
01010
0100
5
01011
0101
6
01110
0110
7
01111
0111
8
10010
1000
9
10011
1001
A
10110
1010
B
10111
1011
C
11010
1100
D
11011
1101
E
11100
1110
F
11101
1111
DATA CODES
IDLE AND CONTROL CODES
H
00100
HALT code-group - Error code
I
11111
Inter-Packet IDLE - 0000 (1)
J
11000
First Start of Packet - 0101 (1)
K
10001
Second Start of Packet - 0101 (1)
T
01101
First End of Packet - 0000 (1)
R
00111
Second End of Packet - 0000 (1)
INVALID CODES
(1)
58
V
00000
V
00001
V
00010
V
00011
V
00101
V
00110
V
01000
V
01100
V
10000
V
11001
Control code-groups I, J, K, T and R in data fields will be mapped as invalid codes, together with RX_ER asserted.
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
7.1.1
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Code-Group Encoding and Injection
The code-group encoder converts 4-bit (4B) nibble data generated by the MAC into 5-bit (5B) code-groups
for transmission. This conversion is required to allow control data to be combined with packet data codegroups. Refer to Table 7-1 for 4B to 5B code-group mapping details.
The code-group encoder substitutes the first 8-bits of the MAC preamble with a J/K code-group pair
(11000 10001) upon transmission. The code-group encoder continues to replace subsequent 4B preamble
and data nibbles with corresponding 5B code-groups. At the end of the transmit packet, upon the
deassertion of Transmit Enable signal from the MAC, the code-group encoder injects the T/R code-group
pair (01101 00111) indicating the end of the frame.
After the T/R code-group pair, the code-group encoder continuously injects IDLEs into the transmit data
stream until the next transmit packet is detected (reassertion of Transmit Enable).
7.1.2
Scrambler
The scrambler is required to control the radiated emissions at the media connector and on the twisted pair
cable (for 100BASE-TX applications). By scrambling the data, the total energy launched onto the cable is
randomly distributed over a wide frequency range. Without the scrambler, energy levels at the PMD and
on the cable could peak beyond FCC limitations at frequencies related to repeating 5B sequences (i.e.,
continuous transmission of IDLEs).
The scrambler is configured as a closed loop linear feedback shift register (LFSR) with an 11-bit
polynomial. The output of the closed loop LFSR is X-ORd with the serial NRZ data from the code-group
encoder. The result is a scrambled data stream with sufficient randomization to decrease radiated
emissions at certain frequencies by as much as 20 dB. The DP83630 uses the PHY_ID (pins PHYAD
[4:0]) to set a unique seed value.
7.1.3
NRZ to NRZI Encoder
After the transmit data stream has been serialized and scrambled, the data must be NRZI encoded in
order to comply with the TP-PMD standard for 100BASE-TX transmission over Category-5 Unshielded
twisted pair cable. There is no ability to bypass this block within the DP83630. The NRZI data is sent to
the 100 Mb Driver. In addition, this module creates an encoded MLT value for use in 100 Mb Internal
Loopback.
7.1.4
Binary to MLT-3 Convertor
The Binary to MLT-3 conversion is accomplished by converting the serial binary data stream output from
the NRZI encoder into two binary data streams with alternately phased logic one events. These two binary
streams are then fed to the twisted pair output driver which converts the voltage to current and alternately
drives either side of the transmit transformer primary winding, resulting in a minimal current MLT-3 signal.
The 100BASE-TX MLT-3 signal sourced by the PMD Output Pair common driver is slew rate controlled.
This should be considered when selecting AC coupling magnetics to ensure TP-PMD Standard compliant
transition times (3 ns < Tr < 5 ns).
The 100BASE-TX transmit TP-PMD function within the DP83630 is capable of sourcing only MLT-3
encoded data. Binary output from the PMD Output Pair is not possible in 100 Mb/s mode.
7.2
100BASE-TX RECEIVER
The 100BASE-TX receiver consists of several functional blocks which convert the scrambled MLT-3 125
Mb/s serial data stream to synchronous 4-bit nibble data that is provided to the MII. Because the
100BASE-TX TP-PMD is integrated, the differential input pins, RD±, can be directly routed from the AC
coupling magnetics.
See Figure 7-2 for a block diagram of the 100BASE-TX receive function. This provides an overview of
each functional block within the 100BASE-TX receive section.
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
59
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
The Receive section consists of the following functional blocks:
— Analog Front End
— Input and BLW Compensation
— Signal Detect
— Digital Adaptive Equalization
— MLT-3 to Binary Decoder
— Clock Recovery Module
— NRZI to NRZ Decoder
— Serial to Parallel
— Descrambler (bypass option)
— Code Group Alignment
— 4B/5B Decoder
— Link Integrity Monitor
— Bad SSD Detection
7.2.1
Analog Front End
In addition to the Digital Equalization and Gain Control, the DP83630 includes Analog Equalization and
Gain Control in the Analog Front End. The Analog Equalization reduces the amount of Digital Equalization
required in the DSP.
7.2.2
Digital Signal Processor
The Digital Signal Processor includes Base Line Wander Compensation and Adaptive Equalization with
Gain Control.
60
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
RD +/-
AFE
ANALOG ANALOG
AGC EQUALIZER
FCO
ADC Data
INPUT BLW
COMPENSATION
ANALOG
ADAPTATION
CONTROL
AUTOMATIC GAIN
CONTROL
CLOCK
RECOVERY
(LOOPFILTER)
DIGITAL
ADAPTIVE
EQUALIZATION
MLT-3 TO BINARY
DECODER
CLOCK
RECOVERY
MODULE
SIGNAL DETECT
NRZI TO NRZ
DECODER
CLOCK
DESCRAMBLER
LINK INTEGRITY
MONITOR
MUX
BP_SCR
CODE GROUP
ALIGNMENT
RX_DATA VALID
SSD DETECT
SERIAL TO
PARALLEL
DIVIDE BY 5
4B/5B DECODER
RX_DV/CRS
RX_CLK
RXD[3:0] / RX_ER
Figure 7-2. 100BASE-TX Receive Block Diagram
7.2.2.1
Base Line Wander Compensation
The DP83630 is completely ANSI TP-PMD compliant and includes Base Line Wander (BLW)
compensation. The BLW compensation block can successfully recover the TP-PMD defined “killer”
pattern.
7.2.2.2
Digital Adaptive Equalization and Gain Control
The DP83630 utilizes an extremely robust equalization scheme referred as ‘Digital Adaptive Equalization.’
The Digital Equalizer removes ISI (inter symbol interference) from the receive data stream by continuously
adapting to provide a filter with the inverse frequency response of the channel. Equalization is combined
with an adaptive gain control stage. This enables the receive 'eye pattern' to be opened sufficiently to
allow very reliable data recovery.
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
61
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
7.2.3
www.ti.com
Signal Detect
The signal detect function of the DP83630 is incorporated to meet the specifications mandated by the
ANSI FDDI TP-PMD Standard as well as the IEEE 802.3 100BASE-TX Standard for both voltage
thresholds and timing parameters.
Note that the reception of normal 10BASE-T link pulses and fast link pulses per IEEE 802.3u AutoNegotiation by the 100BASE-TX receiver do not cause the DP83630 to assert signal detect.
7.2.4
MLT-3 to Binary Decoder
The DP83630 decodes the MLT-3 information from the Digital Adaptive Equalizer block to binary NRZI
data.
7.2.5
Clock Recovery Module
The Clock Recovery function is implemented as a Phase detector and Loop Filter which accepts data and
error from the receive datapath to detect the phase of the recovered data. This phase information is fed
into the loop filter to determine an 8-bit signed frequency control. The 8-bit signed frequency control is
sent to the FCO in the Analog Front End to derive the receive clock. The extracted and synchronized
clock and data are used as required by the synchronous receive operations as generally depicted in
Figure 7-2.
7.2.6
NRZI to NRZ Decoder
In a typical application, the NRZI to NRZ decoder is required in order to present NRZ formatted data to the
descrambler (or to the code-group alignment block if the descrambler is bypassed).
7.2.7
Serial to Parallel
The 100BASE-TX receiver includes a Serial to Parallel converter which supplies 5-bit wide data symbols
to the PCS Rx state machine.
7.2.8
Descrambler
A serial descrambler is used to de-scramble the received NRZ data. The descrambler has to generate an
identical data scrambling sequence (N) in order to recover the original unscrambled data (UD) from the
scrambled data (SD) as represented in the equations:
Synchronization of the descrambler to the original scrambling sequence (N) is achieved based on the
knowledge that the incoming scrambled data stream consists of scrambled IDLE data. After the
descrambler has recognized 12 consecutive IDLE code-groups, where an unscrambled IDLE code-group
in 5B NRZ is equal to five consecutive ones (11111), it will synchronize to the receive data stream and
generate unscrambled data in the form of unaligned 5B code-groups.
In order to maintain synchronization, the descrambler must continuously monitor the validity of the
unscrambled data that it generates. To ensure this, a line state monitor and a hold timer are used to
constantly monitor the synchronization status. Upon synchronization of the descrambler, the hold timer
starts a 722 µs countdown. Upon detection of sufficient IDLE code-groups (58 bit times) within the 722 µs
period, the hold timer will reset and begin a new countdown. This monitoring operation will continue
indefinitely given a properly operating network connection with good signal integrity. If the line state
monitor does not recognize sufficient unscrambled IDLE code-groups within the 722 µs period, the entire
descrambler will be forced out of the current state of synchronization and reset in order to re-acquire
synchronization. The DP83604T also provides a bit (DESC_TIME, bit 7) in the PCSR register (0x16) that
increases the descrambler timeout from 722 µs to 2 ms to allow reception of packets up to 9kB in size
without losing descrambler lock.
62
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
7.2.9
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Code-Group Alignment
The code-group alignment module operates on unaligned 5-bit data from the descrambler (or, if the
descrambler is bypassed, directly from the NRZI/NRZ decoder) and converts it into 5B code-group data (5
bits). Code-group alignment occurs after the J/K code-group pair is detected. Once the J/K code-group
pair (11000 10001) is detected, subsequent data is aligned on a fixed boundary.
7.2.10 4B/5B Decoder
The code-group decoder functions as a look up table that translates incoming 5B code-groups into 4B
nibbles. The code-group decoder first detects the J/K code-group pair preceded by IDLE code-groups and
replaces the J/K with MAC preamble. Specifically, the J/K 10-bit code-group pair is replaced by the nibble
pair (0101 0101). All subsequent 5B code-groups are converted to the corresponding 4B nibbles for the
duration of the entire packet. This conversion ceases upon the detection of the T/R code-group pair
denoting the End of Stream Delimiter (ESD) or with the reception of a minimum of two IDLE code-groups.
7.2.11 100BASE-TX Link Integrity Monitor
The 100BASE-TX link monitor ensures that a valid and stable link is established before enabling both the
Transmit and Receive PCS layer.
Signal detect must be valid for 395 µs to allow the link monitor to enter the 'Link Up' state and enable the
transmit and receive functions.
7.2.12 Bad SSD Detection
A Bad Start of Stream Delimiter (Bad SSD) is any transition from consecutive idle code-groups to non-idle
code-groups which is not prefixed by the code-group pair /J/K.
If this condition is detected, the DP83630 will assert RX_ER and present RXD[3:0] = 1110 to the MII for
the cycles that correspond to received 5B code-groups until at least two IDLE code-groups are detected.
In addition, the False Carrier Sense Counter register (FCSCR) will be incremented by one.
Once at least two IDLE code-groups are detected, RX_ER and CRS become de-asserted.
7.3
100BASE-FX OPERATION
The DP83630 provides IEEE 802.3 compliant 100BASE-FX operation. Configuration of FX mode is via
strap option, or through the register interface.
7.3.1
100BASE-FX Transmit
In 100BASE-FX mode, the device Transmit pins connect to an industry standard Fiber Transceiver with
PECL signaling through a capacitively coupled circuit.
In FX mode, the device bypasses the Scrambler and the MLT3 encoder. This allows for the transmission
of serialized 5B4B encoded NRZI data at 125 MHz.
The only added functionality from 100BASE-TX is the support for Far-End Fault data generation.
7.3.2
100BASE-FX Receive
In 100BASE-FX mode, the device Receive pins connect to an industry standard Fiber Transceiver with
PECL signaling through a capacitively coupled circuit.
In FX mode, the device bypasses the MLT3 Decoder and the Descrambler. This allows for the reception of
serialized 5B4B encoded NRZI data at 125 MHz.
The only added functionality for 100BASE-FX from 100BASE-TX is the support of Far-End Fault detection.
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
63
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
7.3.3
www.ti.com
Far-End Fault
Since 100BASE-FX does not support Auto-Negotiation, a Far-End Fault facility is included which allows for
detection of link failures.
When no signal is being received as determined by the Signal Detect function, the device sends a FarEnd Fault indication to the far-end peer. The Far-End Fault indication is comprised of 3 or more repeating
cycles, each consisting of 84 one’s followed by 1 zero. The pattern is such that it will not satisfy the
100BASE-X carrier sense mechanism, but is easily detected as the Fault indication. The pattern will be
transparent to devices that do not support Far-End Fault.
The Far-End Fault detection process continuously monitors the receive data stream for the Far-End Fault
indication. When detected, the Link Monitor is forced to deassert Link status. This causes the device to
transmit IDLE’s on its transmit path.
7.4
10BASE-T TRANSCEIVER MODULE
The 10BASE-T Transceiver Module is IEEE 802.3 compliant. It includes the receiver, transmitter, collision,
heartbeat, loopback, jabber, and link integrity functions, as defined in the standard. An external filter is not
required on the 10BASE-T interface since this is integrated inside the DP83630. This section focuses on
the general 10BASE-T system level operation.
7.4.1
Operational Modes
The DP83630 has two basic 10BASE-T operational modes:
— Half Duplex mode
— Full Duplex mode
Half Duplex Mode
In Half Duplex mode the DP83630 functions as a standard IEEE 802.3 10BASE-T transceiver supporting
the CSMA/CD protocol.
Full Duplex Mode
In Full Duplex mode the DP83630 is capable of simultaneously transmitting and receiving without
asserting the collision signal. The DP83630's 10 Mb/s ENDEC is designed to encode and decode
simultaneously.
7.4.2
Smart Squelch
The smart squelch is responsible for determining when valid data is present on the differential receive
inputs. The DP83630 implements an intelligent receive squelch to ensure that impulse noise on the
receive inputs will not be mistaken for a valid signal. Smart squelch operation is independent of the
10BASE-T operational mode.
The squelch circuitry employs a combination of amplitude and timing measurements (as specified in the
IEEE 802.3 10BASE-T standard) to determine the validity of data on the twisted pair inputs (refer to
Figure 7-3).
The signal at the start of a packet is checked by the smart squelch and any pulses not exceeding the
squelch level (either positive or negative, depending upon polarity) will be rejected. Once this first squelch
level is overcome correctly, the opposite squelch level must then be exceeded within 150 ns. Finally the
signal must again exceed the original squelch level within 150 ns to ensure that the input waveform will
not be rejected. This checking procedure results in the loss of typically three preamble bits at the
beginning of each packet.
Only after all these conditions have been satisfied will a control signal be generated to indicate to the
remainder of the circuitry that valid data is present. At this time, the smart squelch circuitry is reset.
64
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Valid data is considered to be present until the squelch level has not been generated for a time longer
than 150 ns, indicating the End of Packet. Once good data has been detected, the squelch levels are
reduced to minimize the effect of noise causing premature End of Packet detection.
The receive squelch threshold level can be lowered for use in longer cable or STP applications. This is
achieved by configuring the SQUELCH bits (11:9) in the 10BTSCR register (0x1A).
<150 ns
<150 ns
>150 ns
VSQ+
VSQ+(reduced)
VSQ-(reduced)
VSQ-
start of packet
end of packet
Figure 7-3. 10BASE-T Twisted Pair Smart Squelch Operation
7.4.3
Collision Detection and SQE
When in Half Duplex, a 10BASE-T collision is detected when the receive and transmit channels are active
simultaneously. Collisions are reported by the COL signal on the MII. Collisions are also reported when a
jabber condition is detected.
The COL signal remains set for the duration of the collision. If the ENDEC is receiving when a collision is
detected it is reported immediately (through the COL pin).
When heartbeat is enabled, approximately 1 µs after the transmission of each packet, a Signal Quality
Error (SQE) signal of approximately 10-bit times is generated to indicate successful transmission. SQE is
reported as a pulse on the COL signal of the MII.
The SQE test is inhibited when the PHY is set in full duplex mode. SQE can also be inhibited by setting
the HEARTBEAT_DIS bit (1) in the 10BTSCR register (0x1A).
7.4.4
Carrier Sense
Carrier Sense (CRS) may be asserted due to receive activity once valid data is detected via the squelch
function.
For 10 Mb/s Half Duplex operation, CRS is asserted during either packet transmission or reception.
For 10 Mb/s Full Duplex operation, CRS is asserted only during receive activity.
CRS is deasserted following an end of packet.
7.4.5
Normal Link Pulse Detection/Generation
The link pulse generator produces pulses as defined in the IEEE 802.3 10BASE-T standard. Each link
pulse is nominally 100 ns in duration and transmitted every 16 ms in the absence of transmit data.
Link pulses are used to check the integrity of the connection with the remote end. If valid link pulses are
not received, the link detector disables the 10BASE-T twisted pair transmitter, receiver and collision
detection functions.
When the link integrity function is disabled (FORCE_LINK_10 of the 10BTSCR register), a good link is
forced and the 10BASE-T transceiver will operate regardless of the presence of link pulses.
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
65
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
7.4.6
www.ti.com
Jabber Function
The jabber function monitors the DP83630's output and disables the transmitter if it attempts to transmit a
packet of longer than legal size. A jabber timer monitors the transmitter and disables the transmission if
the transmitter is active for approximately 85 ms.
Once disabled by the Jabber function, the transmitter stays disabled for the entire time that the ENDEC
module's internal transmit enable is asserted. This signal has to be de-asserted for approximately 500 ms
(the “unjab” time) before the Jabber function re-enables the transmit outputs.
The Jabber function is only relevant in 10BASE-T mode.
7.4.7
Automatic Link Polarity Detection and Correction
The DP83630's 10BASE-T transceiver module incorporates an automatic link polarity detection circuit.
When three consecutive inverted link pulses are received, bad polarity is reported. The bad polarity
condition is latched in the 10BTSCR register.
The DP83630's 10BASE-T transceiver module corrects for this error internally and will continue to decode
received data correctly. This eliminates the need to correct the wiring error immediately.
A polarity reversal can be caused by a wiring error at either end of the cable, usually at the Main
Distribution Frame (MDF) or patch panel in the wiring closet.
7.4.8
Transmit and Receive Filtering
External 10BASE-T filters are not required when using the DP83630, as the required signal conditioning is
integrated into the device.
Only isolation transformers and impedance matching resistors are required for the 10BASE-T transmit and
receive interface. The internal transmit filtering ensures that all the harmonics in the transmit signal are
attenuated by at least 30 dB.
7.4.9
Transmitter
The encoder begins operation when the Transmit Enable input (TX_EN) goes high and converts NRZ data
to pre-emphasized Manchester data for the transceiver. For the duration of TX_EN, the serialized
Transmit Data (TXD) is encoded for the transmit-driver pair (PMD Output Pair). TXD must be valid on the
rising edge of Transmit Clock (TX_CLK). Transmission ends when TX_EN de-asserts. The last transition
is always positive; it occurs at the center of the bit cell if the last bit is a one, or at the end of the bit cell if
the last bit is a zero.
7.4.10 Receiver
The decoder consists of a differential receiver and a PLL to separate a Manchester encoded data stream
into internal clock signals and data. The differential input must be externally terminated with a differential
100 Ω termination network to accommodate UTP cable.
The decoder detects the end of a frame when no additional mid-bit transitions are detected. Within one
and a half bit times after the last bit, carrier sense is de-asserted. Receive clock stays active for five more
bit times after CRS goes low, to ensure the receive timings of the controller.
66
Architecture
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
8 Reset Operation
The DP83630 includes an internal power-on reset (POR) function and does not need to be explicitly reset
for normal operation after power up. If required during normal operation, the device can be reset by a
hardware or software reset.
8.1
HARDWARE RESET
A hardware reset is accomplished by applying a low pulse (TTL level), with a duration of at least 1 µs, to
the RESET_N pin. This will reset the device such that all registers will be reinitialized to default values and
the hardware configuration values will be re-latched into the device (similar to the power-up/reset
operation).
8.2
FULL SOFTWARE RESET
A full-chip software reset is accomplished by setting the RESET bit (bit 15) of the Basic Mode Control
Register (BMCR). The period from the point in time when the reset bit is set to the point in time when
software reset has concluded is approximately 1 µs.
The software reset will reset the device such that all registers will be reset to default values and the
hardware configuration values will be maintained. Software driver code must wait 3 µs following a software
reset before allowing further serial MII operations with the DP83630.
8.3
SOFT RESET
A partial software reset can be initiated by setting the SOFT_RESET bit (bit 9) in the PHYCR2 Register.
Setting this bit will reset all transmit and receive operations, but will not reset the register space. All
register configurations will be preserved. Register space will remain available following a soft reset.
8.4
PTP RESET
The entire PTP function, including the IEEE 1588 clock, associated logic, and PTP register space (with
two exceptions), can be reset via the PTP_RESET bit in the PTP_CTL register. The PTP_COC and
PTP_CLKSRC registers are not reset in order to preserve the nominal operation of the clock output.
Reset Operation
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
67
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
9 Design Guidelines
9.1
TPI NETWORK CIRCUIT
Figure 9-1 shows the recommended circuit for a 10/100 Mb/s twisted pair interface.
Below is a partial list of recommended transformers. It is important that the user realize that variations with
PCB and component characteristics requires that the application be tested to ensure that the circuit meets
the requirements of the intended application.
Pulse H1102
Pulse H2019
Vdd
TPRDM
Vdd
COMMON MODE CHOKES
MAY BE REQUIRED
49.9:
0.1 PF
49.9:
1:1
TDRDP
RD0.1 PF*
RD+
TDTD+
TPTDM
0.1 PF*
Vdd
49.9:
1:1
0.1 PF
49.9:
T1
RJ45
NOTE: CENTER TAP IS PULLED TO VDD
*PLACE CAPACITORS CLOSE TO THE
TRANSFORMER CENTER TAPS
TPTDP
All values are typical and are +/- 1%
PLACE RESISTORS AND
CAPACITORS CLOSE TO
THE DEVICE
Figure 9-1. 10/100 Mb/s Twisted Pair Interface
68
Design Guidelines
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
9.2
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
FIBER NETWORK CIRCUIT
Figure 9-2 shows the recommended circuit for a 100 Mb/s fiber pair interface.
Vdd
50:
50:
130:
130:
130:
130:
130:
80:
80:
80:
0.1 PF
FXTDP
FXTDM
Fiber Transceiver
0.1 PF
FXSD
FXRDP
FXRDM
80:
80:
PLACE RESISTORS
CLOSE TO THE FIBER
TRANSCEIVER
PLACE RESISTORS AND
CAPACITORS CLOSE TO
THE DEVICE
All values are typical and are +/- 1%
Figure 9-2. 100 Mb/s Fiber Pair Interface
9.3
ESD PROTECTION
Typically, ESD precautions are predominantly in effect when handling the devices or board before being
installed in a system. In those cases, strict handling procedures need be implemented during the
manufacturing process to greatly reduce the occurrences of catastrophic ESD events. After the system is
assembled, internal components are less sensitive from ESD events.
The network interface pins are more susceptible to ESD events.
9.4
CLOCK IN (X1) RECOMMENDATIONS
The DP83630 supports an external CMOS level oscillator source or a crystal resonator device.
Oscillator
If an external clock source is used, X1 should be tied to the clock source and X2 should be left floating.
The CMOS 25 MHz oscillator specifications for MII Mode are listed in Table 9-1. For RMII Slave Mode, the
CMOS 50 MHz oscillator specifications are listed in Table 9-2. For RMII Slave mode, it is not
recommended that the system clock out, Pin 24, be used as the reference clock to the MAC without first
verifying the interface timing. See SNLA076 for more details.
Design Guidelines
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
69
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Crystal
A 25 MHz, parallel, 20 pF load crystal resonator should be used if a crystal source is desired. Figure 9-3
shows a typical connection for a crystal resonator circuit. The load capacitor values will vary with the
crystal vendors; check with the vendor for the recommended loads.
The oscillator circuit is designed to drive a parallel resonance AT cut crystal with a minimum drive level of
100 µW and a maximum of 500 µW. If a crystal is specified for a lower drive level, a current limiting
resistor should be placed in series between X2 and the crystal.
As a starting point for evaluating an oscillator circuit, if the requirements for the crystal are not known, CL1
and CL2 should be set at 33 pF, and R1 should be set at 0 Ω.
Specification for 25 MHz crystal are listed in Table 9-3.
X1
X2
R1
CL1
CL2
Figure 9-3. Crystal Oscillator Circuit
70
Design Guidelines
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 9-1. 25 MHz Oscillator Specification
Parameter
Min
Frequency
Max
Units
25
Condition
MHz
Frequency Tolerance
±50
ppm
Operational Temperature
Frequency Stability
±50
ppm
1 year aging
Rise / Fall Time
6
nsec
20% - 80%
Jitter
800 (1)
psec
Short term
Jitter
800 (1)
psec
Long term
Symmetry
(1)
Typ
40%
60%
Duty Cycle
This limit is provided as a guideline for component selection and not ensured by production testing. Refer to SNLA091, “PHYTER 100
Base-TX Reference Clock Jitter Tolerance,” for details on jitter performance.
Table 9-2. 50 MHz Oscillator Specification
Parameter
Min
Frequency
Max
Units
50
Condition
MHz
Frequency Tolerance
±50
ppm
Operational Temperature
Frequency Stability
±50
ppm
Operational Temperature
Rise / Fall Time
6
nsec
20% - 80%
Jitter
800 (1)
psec
Short term
Jitter
800 (1)
psec
Long term
Symmetry
(1)
Typ
40%
60%
Duty Cycle
This limit is provided as a guideline for component selection and not ensured by production testing. Refer to SNLA091, “PHYTER 100
Base-TX Reference Clock Jitter Tolerance,” for details on jitter performance.
Table 9-3. 25 MHz Crystal Specification
Parameter
Min
Frequency
Typ
Max
Units
25
Condition
MHz
Frequency Tolerance
±50
ppm
Operational Temperature
Frequency Stability
±50
ppm
1 year aging
40
pF
Range of CL1and CL2
Shunt Capacitance
25
Design Guidelines
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
71
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10 Register Block
Table 10-1. Register Map
Offset
Access
Tag
0
RW
BMCR
Basic Mode Control Register
1
RO
BMSR
Basic Mode Status Register
02h
2
RO
PHYIDR1
PHY Identifier Register #1
03h
3
RO
PHYIDR2
PHY Identifier Register #2
04h
4
RW
ANAR
05h
5
RW
ANLPAR
06h
6
RW
ANER
07h
7
RW
ANNPTR
08h-0Fh
8-15
10h
16
RO
PHYSTS
11h
17
RW
MICR
MII Interrupt Control Register
12h
18
RW
MISR
MII Interrupt Status and Event Control Register
13h
19
RW
PAGESEL
Hex
Decimal
00h
01h
Description
Auto-Negotiation Advertisement Register
Auto-Negotiation Link Partner Ability Register
Auto-Negotiation Expansion Register
RESERVED
Auto-Negotiation Next Page TX Register
RESERVED
PHY Status Register
Page Select Register
Extended Registers - Page 0
14h
20
RO
FCSCR
15h
21
RO
RECR
False Carrier Sense Counter Register
Receive Error Counter Register
16h
22
RW
PCSR
PCS Sub-Layer Configuration and Status Register
17h
23
RW
RBR
18h
24
RW
LEDCR
LED Direct Control Register
19h
25
RW
PHYCR
PHY Control Register
1Ah
26
RW
10BTSCR
10Base-T Status/Control Register
1Bh
27
RW
CDCTRL1
CD Test Control Register and BIST Extensions Register
1Ch
28
RW
PHYCR2
PHY Control Register 2
1Dh
29
RW
EDCR
1Eh
30
1Fh
31
RMII and Bypass Register
Energy Detect Control Register
RESERVED
RW
PCFCR
RESERVED
PHY Control Frames Configuration Register
Test Registers - Page 1
14h - 1Dh
20 - 29
1Eh
30
1Fh
31
RESERVED
RW
SD_CNFG
RESERVED
RESERVED
Signal Detect Configuration
RESERVED
Link Diagnostics Registers - Page 2
14h
20
RO
LEN100_DET
15h
21
RW
FREQ100
16h
22
RW
TDR_CTRL
TDR Control Register
17h
23
RW
TDR_WIN
TDR Window Register
18h
24
RO
TDR_PEAK
19h
25
RO
TDR_THR
TDR Threshold Measurement Register
1Ah
26
RW
VAR_CTRL
Variance Control Register
1Bh
27
RO
VAR_DAT
Variance Data Register
1Ch
28
1Dh
29
RW
LQMR
Link Quality Monitor Register
1Eh
30
RW
LQDR
Link Quality Data Register
1Fh
31
RW
LQMR2
RESERVED
100 Mb Length Detect Register
100 Mb Frequency Offset Indication Register
TDR Peak Measurement Register
RESERVED
Link Quality Monitor Register 2
Reserved Registers - Page 3
14h - 1Fh
20 - 31
RESERVED
RESERVED
PTP 1588 Base Registers - Page 4
72
14h
20
RW
PTP_CTL
PTP Control Register
15h
21
RW
PTP_TDR
PTP Time Data Register
16h
22
RW
PTP_STS
PTP Status Register
17h
23
RW
PTP_TSTS
PTP Trigger Status Register
18h
24
RW
PTP_RATEL
PTP Rate Low Register
19h
25
RW
PTP_RATEH
PTP Rate High Register
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-1. Register Map (continued)
Offset
Access
Tag
Description
Hex
Decimal
1Ah
26
RO
PTP_RDCKSUM
PTP Page 4 Read Checksum
1Bh
27
RO
PTP_WRCKSUM
PTP Page 4 Write Checksum
1Ch
28
RO
PTP_TXTS
PTP Transmit TimeStamp Register
1Dh
29
RO
PTP_RXTS
PTP Receive TimeStamp Register
1Eh
30
RO
PTP_ESTS
PTP Event Status Register
1Fh
31
RO
PTP_EDATA
PTP Event Data Register
PTP 1588 Configuration Registers - Page 5
14h
20
RW
PTP_TRIG
PTP Trigger Configuration Register
15h
21
RW
PTP_EVNT
PTP Event Configuration Register
16h
22
RW
PTP_TXCFG0
PTP Transmit Configuration Register 0
17h
23
RW
PTP_TXCFG1
PTP Transmit Configuration Register 1
18h
24
RW
PSF_CFG0
19h
25
RW
PTP_RXCFG0
PTP Receive Configuration Register 0
1Ah
26
RW
PTP_RXCFG1
PTP Receive Configuration Register 1
1Bh
27
RW
PTP_RXCFG2
PTP Receive Configuration Register 2
1Ch
28
RW
PTP_RXCFG3
PTP Receive Configuration Register 3
1Dh
29
RW
PTP_RXCFG4
PTP Receive Configuration Register 4
1Eh
30
RW
PTP_TRDL
PTP Temporary Rate Duration Low Register
1Fh
31
RW
PTP_TRDH
PTP Temporary Rate Duration High Register
PHY Status Frames Configuration Register 0
PTP 1588 Configuration Registers - Page 6
14h
20
RW
PTP_COC
PTP Clock Output Control Register
15h
21
RW
PSF_CFG1
PHY Status Frames Configuration Register 1
16h
22
RW
PSF_CFG2
PHY Status Frames Configuration Register 2
17h
23
RW
PSF_CFG3
PHY Status Frames Configuration Register 3
18h
24
RW
PSF_CFG4
PHY Status Frames Configuration Register 4
19h
25
RW
PTP_SFDCFG
1Ah
26
RW
PTP_INTCTL
PTP Interrupt Control Register
1Bh
27
RW
PTP_CLKSRC
PTP Clock Source Register
1Ch
28
RW
PTP_ETR
PTP Ethernet Type Register
1Dh
29
RW
PTP_OFF
PTP Offset Register
1Eh
30
RO
PTP_GPIOMON
PTP GPIO Monitor Register
1Fh
31
RW
PTP_RXHASH
PTP Receive Hash Register
PTP SFD Configuration Register
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
73
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-2. Register Table
Register Name
Addr
Tag
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Basic Mode
Control Register
00h
BMCR
Reset
Loopback
Speed
Selection
Auto-Neg
Enable
Power
Down
Isolate
Restart
Auto-Neg
Duplex
Mode
Collision
Test
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Basic Mode Status 01h
Register
BMSR
100BaseT4
100BaseTX FDX
100BaseTX HDX
10Base-T
10Base-T
Reserved
Reserved
Reserved
MF
Preamble
Suppress
Link
Complete
Remote
Fault
Auto-Neg
HDX
Unidirectio
nal Ability
Auto-Neg
FDX
Ability
Status
PHY Identifier
Register #1
02h
PHYIDR1
OUI MSB OUI MSB
PHY Identifier
Register #2
03h
PHYIDR2
OUI LSB
Auto-Negotiation
Advertisement
Register
04h
OUI LSB
OUI MSB
OUI LSB
OUI MSB
OUI LSB
OUI MSB
OUI LSB
Jabber Detect Extended
Capability
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI MSB
OUI LSB
VNDR_
VNDR_
VNDR_
VNDR_
VNDR_
VNDR_
MDL_
MDL_
MDL_
MDL_
MDL
MDL
MDL
MDL
MDL
MDL
REV
REV
REV
REV
ANAR
Next Page
Ind
Reserved
Remote
Fault
Reserved
ASM_DIR
PAUSE
T4
TX_FD
TX
10_FD
10
Protocol
Selection
Protocol
Selection
Protocol
Selection
Protocol
Selection
Protocol
Selection
Auto-Negotiation
05h
Link Partner Ability
Register (Base
Page)
ANLPAR
Next Page
Ind
ACK
Remote
Fault
Reserved
ASM_DIR
PAUSE
T4
TX_FD
TX
10_FD
10
Protocol
Selection
Protocol
Selection
Protocol
Selection
Protocol
Selection
Protocol
Selection
Auto-Negotiation
05h
Link Partner Ability
Register Next
Page
ANLPARN
P
Next Page
Ind
ACK
Message
Page
ACK2
Toggle
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Code
Auto-Negotiation
Expansion
Register
06h
ANER
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PDF
LP_NP_
NP_
PAGE_
LP_AN_
ABLE
ABLE
RX
ABLE
Auto-Negotiation
Next Page TX
Register
07h
ANNPTR
Next Page
Ind
Reserved
Message
Page
ACK2
TOG_TX
CODE
CODE
CODE
CODE
CODE
RESERVED
08-0fh
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PHY Status
Register
10h
PHYSTS
Reserved MDIX
mode
Rx Err
Latch
Polarity
Status
False
Carrier
Sense
MII Interrupt
Control Register
11h
MICR
Reserved
Reserved
Reserved
Reserved
MII Interrupt Status 12h
and Misc. Control
Register
MISR
LQ_INT
ED_INT
LINK_INT
Page Select
Register
13h
Reserved
Reserved
Reserved
False Carrier
Sense Counter
Register
14h
FCSCR
Reserved
Receive Error
Counter Register
15h
RECR
PCS Sub-Layer
Configuration and
Status Register
16h
PCSR
RMII and Bypass
Register
17h
CODE
CODE
CODE
CODE
Reserved
Reserved
Reserved
Reserved
Reserved
Signal
Detect
Descrambl
er Lock
Page
MII
Interrupt
Remote
Fault
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SPD_INT
or
SPD_DUP
_INT
DUP_INT
or
PTP_INT
ANC_INT
FHF_INT
or
CTR_INT
RHF_INT
or
PCF_INT
LQ_INT_E ED_INT_E LINK_INT_EN SPED_INT DUP_INT_EN ANC_INT_ FHF_INT_EN RHF_INT_
N
N
_EN
EN
or
EN
CTR_INT_EN
or
PCF_INT_
EN
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Page_Sel
Bit
Page_Sel Bit
Page_Sel
Bit
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
FCSCNT
FCSCNT
FCSCNT
FCSCNT
FCSCNT
FCSCNT
FCSCNT
FCSCNT
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RXERCNT
RXERCNT
RXERCNT
RXERCNT
RXERCNT
RXERCNT
AUTO_CR
OSSOVER
Reserved
Reserved
Reserved FREE_CLK
TQ_EN
SD_FORC
E_PMA
FORCE_
Reserved
FEFI_EN
NRZI_
SCRAM_
DE
BYPASS
BYPASS
SCRAM_B
YPASS
Receive
CODE
CODE
Reserved
Reserved
Reserved
Reserved
Reserved
Jabber Detect Auto-Neg
Loopback
Status
Duplex
Status
Speed Status
PTP_INT_SE
L
TINT
INTEN
Complete
Reserved
Reserved
Link
Status
INT_OE
EXTENDED REGISTERS - PAGE 0
74
RBR
Reserved RMII_MAS DIS_TX_O
TER
PT
SD_
OPTION
RXERCNT RXERCNT
DESC_TIM
E
FX_EN
RX_PORT RX_PORT TX_SOUR TX_SOUR PMD_LOO SCMII_RX SCMII_TX
CE
CE
P
Register Block
100_OK
RMII_MODE RMII_REV RX_OVF_ST RX_UNF_S ELAST_BUF ELAST_BU
1_0
S
TS
F
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-2. Register Table (continued)
Register Name
Addr
Tag
Bit 15
Bit 14
Bit 13
Bit 12
Reserved
Reserved
Reserved
LED Direct Control 18h
Register
LEDCR
Reserved
PHY Control
Register
19h
PHYCR
MDIX_EN FORCE_M PAUSE_R PAUSE_TX
DIX
X
10Base-T
Status/Control
Register
1Ah
CD Test Control
and BIST
Extensions
Register
1Bh
CDCTRL1
PHY Control
Register 2
1Ch
PHYCR2
Energy Detect
Control Register
1Dh
EDCR
RESERVED
1Eh
Reserved
PHY Control
Frames
Configuration
Register
1Fh
PCFCR
RESERVED
14h-1Dh
Reserved
Reserved
Reserved
Signal Detect
Configuration
Register
1Eh
SD_CNFG
Reserved
RESERVED
1Fh
Reserved
Reserved
10BTSCR
Reserved
Reserved
Reserved
Reserved
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
BIST_FE
PSR_15
BIST_
STATUS
BIST_STA BP_STRET
RT
CH
SQUELCH SQUELCH SQUELCH LOOPBAC
K_10_DIS
LP_DIS
ED_EN
Reserved
Bit 5
Bit 4
Bit 3
SYNC_EN CLK_OUT BC_WRITE PHYTER_
ET_EN
RXCLK
COMP
SOFT_RE
SET
Reserved
Reserved
Bit 2
Bit 1
Bit 0
SPDLED
LNKLED
ACTLED
LED_
LED_
PHY
PHY
PHY
PHY
PHY
CNFG[1]
CNFG[0]
ADDR
ADDR
ADDR
ADDR
ADDR
FORCE_
LINK_10
BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR Reserved
OR_COUN OR_COUN OR_COUN OR_COUN OR_COUN OR_COUN OR_COUN OR_COUN
T
T
T
T
T
T
T
T
Reserved
Bit 6
DIS_SPDL DIS_LNKL DIS_ACTL LEDACT_R BLINK_FR BLINK_FR DRV_SPDLE DRV_LNKL DRV_ACTLE
ED
ED
ED
X
EQ
EQ
D
ED
D
FORCE_POL POLARITY AUTOPOL_DI 10BT_SCA HEARTBEAT JABBER_D
COR
S
LE_MSB
_DIS
IS
MII_CLOC
K_EN
BIST_CONT
Reserved
Reserved
CDPATTE MDIO_PULL_ PATT_GAP CDPATTSEL CDPATTS
N_10
EN
_10M
EL
Reserved
Reserved
Reserved CLK_OUT_DI Reserved
S
ED_AUTO ED_AUTO
_UP
_DOWN
ED_MAN
ED_BURS ED_PWR_ ED_ERR_ ED_DATA_ ED_ERR_
T_DIS
STATE
MET
MET
COUNT
ED_ERR_ ED_ERR_CO ED_ERR_ ED_DATA_C ED_DATA_ ED_DATA_C ED_DATA_
COUNT
UNT
COUNT
OUNT
COUNT
OUNT
COUNT
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PCF_STS_ PCF_STS_ Reserved
ERR
OK
Reserved
Reserved
Reserved
Reserved PCF_DA_S PCF_INT_ PCF_INT_ PCF_BC_DIS PCF_BUF
EL
CTL
CTL
PCF_BUF
PCF_BUF
PCF_BUF
PCF_EN
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SD_Time
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TEST REGISTERS - PAGE 1
LINK DIAGNOSTICS REGISTERS - PAGE 2
100 Mb Length
Detect Register
14h
LEN100_D
ET
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved CABLE_LE CABLE_LE CABLE_LEN CABLE_LE CABLE_LEN CABLE_LE CABLE_LEN CABLE_LE
N
N
N
N
N
SAMPLE_F Reserved
REQ
Reserved
Reserved
Reserved
Reserved
Reserved
SEL_FC
100 Mb Frequency 15h
Offset Indication
Register
FREQ100
FREQ_OF FREQ_OF FREQ_OFFS FREQ_OF FREQ_OFFS FREQ_OF FREQ_OFFS FREQ_OF
FSET
FSET
ET
FSET
ET
FSET
ET
FSET
TDR Control
Register
16h
TDR_CTRL TDR_ENA TDR_100M TX_CHAN RX_CHAN SEND_TD TDR_WIDT TDR_WIDT TDR_WIDT TDR_MIN_
BLE
b
NEL
NEL
R
H
H
H
MODE
TDR Window
Register
17h
TDR_WIN
TDR_STA
RT
TDR_STA
RT
TDR_STA
RT
TDR_STA
RT
TDR_STA
RT
TDR_STA
RT
TDR_STA
RT
TDR_STA
RT
TDR_STO TDR_STO
P
P
TDR_STOP
TDR Peak
Measurement
Register
18h
TDR_PEA
K
Reserved
Reserved
TDR_PEA
K
TDR_PEA
K
TDR_PEA
K
TDR_PEA
K
TDR_PEA
K
TDR_PEA
K
TDR_PEA
K_TIME
TDR_PEAK_ TDR_PEA
TIME
K_TIME
TDR Threshold
Measurement
Register
19h
TDR_THR
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved TDR_THR_
TDRTDRMET
THR_TIME THR_TIME
Variance Control
Register
1Ah
VAR_CTRL VAR_RDY
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Variance Data
Register
1Bh
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT
A
VAR_DAT VAR_DATA
A
Reserved
1Ch
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Link Quality
Monitor Register
1Dh
LQMR
LQM_ENA RESTART_ RESTART_ RESTART_ RESTART_ RESTART_ FC_HI_WA FC_LO_W FREQ_HI_ FREQ_LO_ DBLW_HI_W
BLE
ON_FC
ON_FREQ ON_DBLW ON_DAGC
ON_C1
RN
ARN
WARN
WARN
ARN
Reserved
TDR_PEA
K_TIME
RX_THRESH RX_THRE RX_THRESH RX_THRE RX_THRESH RX_THRE
OLD
SHOLD
OLD
SHOLD
OLD
SHOLD
TDRTHR_TIME
TDR_STO
P
TDRTHR_TIME
TDR_STOP
TDR_STO
P
TDR_STOP
TDR_PEAK_ TDR_PEA TDR_PEAK_ TDR_PEA
TIME
K_TIME
TIME
K_TIME
TDRTHR_TIME
TDRTHR_TIME
TDRTHR_TIME
LOAD_VAR_ LOAD_VA VAR_FREEZ VAR_TIME VAR_TIMER
HI
R_LO
E
R
Reserved
TDR_STO
P
VAR_DAT
A
VAR_DATA
Reserved
Reserved
VAR_DAT VAR_DATA
A
Reserved
TDRTHR_TIME
VAR_ENA
BLE
VAR_DAT
A
Reserved
DBLW_LO DAGC_HI_W DAGC_LO C1_HI_WAR
_WARN
ARN
_WARN
N
Reserved
C1_LO_W
ARN
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
75
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-2. Register Table (continued)
Register Name
Addr
Tag
Bit 15
Bit 14
Link Quality Data
Register
1Eh
Bit 13
Bit 12
LQDR
Reserved
Reserved
SAMPLE_ WRITE_LQ LQ_PARA
PARAM
_THR
M_SEL
Bit 11
Bit 10
Link Quality
1Fh
Monitor Register 2
LQMR2
Reserved
Reserved
Reserved
Reserved
Reserved RESTART_ Reserved
ON_VAR
RESERVED
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
LQ_PARA
M_SEL
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
LQ_PARA LQ_THR_S LQ_THR_D LQ_THR_D LQ_THR_DA LQ_THR_D LQ_THR_DA LQ_THR_D LQ_THR_DA LQ_THR_D
M_SEL
EL
ATA
ATA
TA
ATA
TA
ATA
TA
ATA
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
VAR_HI_WA
RN
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RESERVED REGISTERS - PAGE 3
14h-1Fh
Reserved
Reserved
Reserved
PTP 1588 BASE REGISTERS - PAGE 4
PTP Control
Register
14h
PTP_CTL
PTP Time Data
Register
15h
PTP_TDR
PTP Status
Register
16h
PTP_STS
Reserved
Reserved
Reserved
TRIG_SEL TRIG_SEL TRIG_SEL TRIG_DIS
TRIG_EN TRIG_REA TRIG_LOA PTP_RD_CL PTP_LOAD PTP_STEP_ PTP_ENAB PTP_DISABL PTP_RESE
D
D
K
_CLK
CLK
LE
E
T
TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DATA TIME_DAT TIME_DATA TIME_DAT TIME_DATA TIME_DAT
A
A
A
A
A
A
A
A
A
A
A
A
A
Reserved
Reserved
Reserved
Reserved TXTS_RDY RXTS_RD TRIG_DON EVENT_R
Y
E
DY
Reserved
Reserved
Reserved
Reserved
TXTS_IE
RXTS_IE
TRIG_IE
EVENT_IE
PTP Trigger Status 17h
Register
PTP_TSTS TRIG7_ER TRIG7_AC TRIG6_ER TRIG6_AC TRIG5_ER TRIG5_AC TRIG4_ER TRIG4_AC TRIG3_ER TRIG3_AC TRIG2_ERR TRIG2_AC TRIG1_ERR TRIG1_AC TRIG0_ERR TRIG0_AC
ROR
TIVE
ROR
TIVE
ROR
TIVE
ROR
TIVE
ROR
TIVE
OR
TIVE
OR
TIVE
OR
TIVE
PTP Rate Low
Register
18h
PTP_RATE PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_Lo PTP_Rate_ PTP_Rate_Lo PTP_Rate_ PTP_Rate_Lo PTP_Rate_
L
Lo
Lo
Lo
Lo
Lo
Lo
Lo
Lo
Lo
Lo
Lo
Lo
Lo
PTP Rate High
Register
19h
PTP_RATE PTP_RATE PTP_TMP_ Reserved
H
_DIR
RATE
Reserved
Reserved
Reserved PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_ PTP_Rate_Hi PTP_Rate_ PTP_Rate_Hi PTP_Rate_ PTP_Rate_Hi PTP_Rate_
Hi
Hi
Hi
Hi
Hi
Hi
Hi
PTP Page 4 Read 1Ah
Checksum
PTP_RDC
KSUM
RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU
M
M
M
M
M
M
M
M
M
M
PTP Page 4 Write 1Bh
Checksum
PTP_WRC WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSUM WR_CKSU WR_CKSUM WR_CKSU WR_CKSUM WR_CKSU
KSUM
M
M
M
M
M
M
M
M
M
M
M
M
M
PTP Transmit
TimeStamp
Register
1Ch
PTP_TXTS PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_TS PTP_TX_T PTP_TX_TS PTP_TX_T PTP_TX_TS PTP_TX_T
S
S
S
S
S
S
S
S
S
S
S
S
S
PTP Receive
TimeStamp
Register
1Dh
PTP_RXTS PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_TS PTP_RX_T PTP_RX_TS PTP_RX_T PTP_RX_TS PTP_RX_T
S
S
S
S
S
S
S
S
S
S
S
S
S
PTP Event Status
Register
1Eh
PTP_ESTS
Reserved
Reserved
Reserved
Reserved
Reserved
PTP Event Data
Register Status
1Fh
PTP_EDAT
A
E7_RISE
E7_DET
E6_RISE
E6_DET
E5_RISE
PTP Event Data
Register
Timestamp
1Fh
PTP_EDAT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT PTP_EVNT_T PTP_EVNT PTP_EVNT_T PTP_EVNT PTP_EVNT_T PTP_EVNT
A
_TS
_TS
_TS
_TS
_TS
_TS
_TS
_TS
_TS
_TS
S
_TS
S
_TS
S
_TS
PTP Trigger
Configuration
Register
14h
PTP_TRIG TRIG_PUL TRIG_PER TRIG_IF_L TRIG_NOT TRIG_GPI TRIG_GPI TRIG_GPI TRIG_GPI TRIG_TOG Reserved
SE
ATE
IFY
O
O
O
O
GLE
Reserved
Reserved
TRIG_CSEL TRIG_CSE TRIG_CSEL
L
TRIG_WR
PTP Event
Configuration
Register
15h
PTP_EVNT Reserved
Reserved
Reserved
EVNT_SEL
EVNT_WR
PTP Transmit
Configuration
Register 0
16h
PTP_TXCF SYNC_1ST Reserved DR_INSER Reserved
G0
EP
T
PTP Transmit
Configuration
Register 1
17h
PTP_TXCF BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_DA BYTE0_DA BYTE0_DAT BYTE0_DA BYTE0_DAT BYTE0_DA BYTE0_DAT BYTE0_DA
G1
SK
SK
SK
SK
SK
SK
SK
SK
TA
TA
A
TA
A
TA
A
TA
EVNTS_MI EVNTS_MI EVNTS_MI EVNT_TS_ EVNT_TS_
SSED
SSED
SSED
LEN
LEN
E5_DET
E4_RISE
E4_DET
E3_RISE
E3_DET
RD_CKSUM
RD_CKSU
M
RD_CKSUM
EVNT_RF
EVNT_NU
M
EVNT_NUM
E2_RISE
E2_DET
E1_RISE
RD_CKSU
M
RD_CKSUM
RD_CKSU
M
EVNT_NU MULT_EVNT EVENT_D
M
ET
E1_DET
E0_RISE
E0_DET
PTP 1588 CONFIGURATION REGISTERS - PAGE 5
76
EVNT_RIS EVNT_FAL Reserved
E
L
EVNT_GPI EVNT_GPI EVNT_GPI EVNT_GPI
O
O
O
O
Reserved
Reserved
EVNT_SEL
EVNT_SEL
RESERVE CRC_1STE CHK_1STE IP1588_EN TX_L2_EN TX_IPV6_E TX_IPV4_EN TX_PTP_V TX_PTP_VE TX_PTP_V TX_PTP_VE TX_TS_EN
D_1
P
P
N
ER
R
ER
R
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-2. Register Table (continued)
Register Name
Addr
Tag
Bit 15
Bit 14
Bit 13
Reserved
Reserved
Bit 12
Bit 11
Bit 10
MAC_SRC MAC_SRC MIN_PRE
_ADD
_ADD
Bit 9
MIN_PRE
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PHY Status Frame 18h
Configuration
Register 0
PSF_CFG0 Reserved
MIN_PRE PSF_ENDI PSF_IPV4 PSF_PCF_R PSF_ERR_ PSF_TXTS_E PSF_RXTS PSF_TRIG_E PSF_EVNT
AN
D
EN
N
_EN
N
_EN
PTP Receive
Configuration
Register 0
19h
PTP_RXCF DOMAIN_E Reserved
G0
N
PTP Receive
Configuration
Register 1
1Ah
PTP_RXCF BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_MA BYTE0_DA BYTE0_DA BYTE0_DAT BYTE0_DA BYTE0_DAT BYTE0_DA BYTE0_DAT BYTE0_DA
G1
SK
SK
SK
SK
SK
SK
SK
SK
TA
TA
A
TA
A
TA
A
TA
PTP Receive
Configuration
Register 2
1Bh
PTP_RXCF IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_DA IP_ADDR_ IP_ADDR_DA IP_ADDR_ IP_ADDR_DA IP_ADDR_
G2
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
TA
DATA
TA
DATA
TA
DATA
PTP Receive
Configuration
Register 3
1Ch
PTP_RXCF TS_MIN_IF TS_MIN_IF TS_MIN_IF TS_MIN_IF ACC_UDP ACC_CRC TS_APPEN TS_INSER PTP_DOM PTP_DOM PTP_DOMAI PTP_DOM PTP_DOMAI PTP_DOM PTP_DOMAI PTP_DOM
G3
G
G
G
G
D
T
AIN
AIN
N
AIN
N
AIN
N
AIN
PTP Receive
Configuration
Register 4
1Dh
PTP_RXCF IPV4_UDP TS_SEC_E TS_SEC_L TS_SEC_L RXTS_NS_ RXTS_NS_ RXTS_NS_ RXTS_NS_ RXTS_NS_ RXTS_NS_ RXTS_SEC_ RXTS_SE
G4
_MOD
N
EN
EN
OFF
OFF
OFF
OFF
OFF
OFF
OFF
C_OFF
USER_IP_ USER_IP_ RX_SLAVE IP1588_EN IP1588_EN IP1588_EN RX_L2_EN RX_IPV6_ RX_IPV4_EN RX_PTP_V RX_PTP_VE RX_PTP_V RX_PTP_VE RX_TS_EN
SEL
EN
EN
ER
R
ER
R
RXTS_SEC_ RXTS_SE
OFF
C_OFF
RXTS_SEC_
OFF
RXTS_SE
C_OFF
PTP Temporary
1Eh
Rate Duration Low
Register
PTP_TRDL PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_DU PTP_TR_D PTP_TR_DU PTP_TR_D PTP_TR_DU PTP_TR_D
URL
URL
URL
URL
URL
URL
URL
URL
URL
URL
RL
URL
RL
URL
RL
URL
PTP Temporary
1Fh
Rate Duration High
Register
PTP_TRD
H
Reserved
Reserved
PTP Clock Output 14h
Control Register
PTP_COC PTP_CLKO PTP_CLKO PTP_CLKO Reserved
UT EN
UT SEL
UT
SPEEDSE
L
Reserved
PHY Status Frame 15h
Configuration
Register 1
PSF_CFG1 PTPRESE PTPRESE PTPRESE PTPRESE VERSIONP VERSIONP VERSIONP VERSIONP TRANSPO TRANSPO TRANSPORT TRANSPO MESSAGETY MESSAGE MESSAGETY MESSAGE
RVED
RVED
RVED
RVED
TP
TP
TP
TP
RTSPECIFI RTSPECIFI SPECIFIC RTSPECIFI
PE
TYPE
PE
TYPE
C
C
C
Status Frame
Configuration
Register 2
16h
PSF_CFG2 IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BYTE IP_SA_BY IP_SA_BYTE IP_SA_BY IP_SA_BYTE IP_SA_BY
TE1
TE1
TE1
TE1
TE1
TE1
TE1
TE1
TE0
TE0
0
TE0
0
TE0
0
TE0
Status Frame
Configuration
Register 3
17h
PSF_CFG3 IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BYTE IP_SA_BY IP_SA_BYTE IP_SA_BY IP_SA_BYTE IP_SA_BY
TE3
TE3
TE3
TE3
TE3
TE3
TE3
TE3
TE2
TE2
2
TE2
2
TE2
2
TE2
Status Frame
Configuration
Register 4
18h
PSF_CFG4 IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSUM IP_CHKSU IP_CHKSUM IP_CHKSU IP_CHKSUM IP_CHKSU
M
M
M
M
M
M
M
M
M
M
M
M
M
PTP SFD
Congiguration
Register
19h
PTP_SFDC Reserved
FG
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved TX_SFD_G TX_SFD_G TX_SFD_GPI TX_SFD_G RX_SFD_GPI RX_SFD_ RX_SFD_GPI RX_SFD_
PIO
PIO
O
PIO
O
GPIO
O
GPIO
PTP Interrupt
Control Register
1Ah
PTP_INTC
TL
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PTP Clock Source 1Bh
Register
PTP_CLKS CLK_SRC
RC
CLK_SRC
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved CLK_SRC_ CLK_SRC_P CLK_SRC_ CLK_SRC_P CLK_SRC_ CLK_SRC_P CLK_SRC_
PER
ER
PER
ER
PER
ER
PER
PTP Ethernet Type 1Ch
Register
PTP_ETR
PTP Offset
Register
PTP_OFF
Reserved
Reserved
Reserved
Reserved PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_DU PTP_TR_D PTP_TR_DU PTP_TR_D PTP_TR_DU PTP_TR_D
URH
URH
URH
URH
RH
URH
RH
URH
RH
URH
PTP 1588 CONFIGURATION REGISTERS - PAGE 6
1Dh
Reserved
Reserved
Reserved PTP_CLKD PTP_CLKD PTP_CLKDIV PTP_CLKD PTP_CLKDIV PTP_CLKD PTP_CLKDIV PTP_CLKD
IV
IV
IV
IV
IV
Reserved
Reserved
Reserved
PTP_INT_GP PTP_INT_ PTP_INT_GP PTP_INT_
IO
GPIO
IO
GPIO
PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYPE PTP_ETYP PTP_ETYPE PTP_ETYP PTP_ETYPE PTP_ETYP
E
E
E
E
E
E
E
E
E
E
E
E
E
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved PTP_OFFS PTP_OFFS PTP_OFFSE PTP_OFFS PTP_OFFSE PTP_OFFS PTP_OFFSE PTP_OFFS
ET
ET
T
ET
T
ET
T
ET
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
77
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-2. Register Table (continued)
Register Name
Addr
Tag
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PTP GPIO Monitor 1Eh
Register
PTP_GPIO
MON
Reserved
Reserved
Reserved
Reserved
PTP Receive Hash 1Fh
Register
PTP_RXH
ASH
Reserved
Reserved
Reserved
RX_HASH PTP_RX_H PTP_RX_H PTP_RX_H PTP_RX_H PTP_RX_H PTP_RX_H PTP_RX_HA PTP_RX_H PTP_RX_HA PTP_RX_H PTP_RX_HA PTP_RX_H
_EN
ASH
ASH
ASH
ASH
ASH
ASH
SH
ASH
SH
ASH
SH
ASH
78
PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO_I PTP_GPIO PTP_GPIO_I PTP_GPIO PTP_GPIO_I PTP_GPIO
_IN
_IN
_IN
_IN
_IN
_IN
N
_IN
N
_IN
N
_IN
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.1 REGISTER DEFINITION
In the register definitions under the ‘Default’ heading, the following definitions hold true:
— RW = Read Write access
— SC = Register sets on event occurrence and Self-Clears when event ends
— RW/SC = ReadWrite access/Self Clearing bit
— RO = Read Only access
— COR = Clear On Read
— RO/COR = Read Only, Clear On Read
— RO/P = Read Only, Permanently set to a default value
— LL = Latched Low and held until read, based upon the occurrence of the corresponding event
— LH = Latched High and held until read, based upon the occurrence of the corresponding event
10.1.1 Basic Mode Control Register (BMCR)
Table 10-3. Basic Mode Control Register (BMCR), address 0x00
Bit
Bit Name
Default
15
RESET
0, RW/SC
Description
Reset:
1 = Initiate software Reset / Reset in Process.
0 = Normal operation.
This bit, which is self-clearing, returns a value of one until the reset process is complete.
The configuration is re-strapped.
14
LOOPBACK
0, RW
Loopback:
1 = Loopback enabled.
0 = Normal operation.
The loopback function enables MII transmit data to be routed to the MII receive data
path.
Setting this bit may cause the descrambler to lose synchronization and produce a 500
µs “dead time” before any valid data will appear at the MII receive outputs.
13
SPEED SELECTION
Strap, RW
Speed Select:
When auto-negotiation is disabled writing to this bit allows the port speed to be selected.
1 = 100 Mb/s.
0 = 10 Mb/s.
12
AUTO-NEGOTIATION
ENABLE
Strap, RW
Auto-Negotiation Enable:
Strap controls initial value at reset.
If FX is enabled (FX_EN = 1), then this bit will be reset to 0.
1 = Auto-Negotiation Enabled - bits 8 and 13 of this register are ignored when this bit is
set.
0 = Auto-Negotiation Disabled - bits 8 and 13 determine the port speed and duplex
mode.
11
POWER DOWN
0, RW
Power Down:
1 = Power down.
0 = Normal operation.
Setting this bit powers down the PHY. Only the register block is enabled during a power
down condition. This bit is ORd with the input from the PWRDOWN_INT pin. When the
active low PWRDOWN_INT pin is asserted, this bit will be set.
10
ISOLATE
0, RW
Isolate:
1 = Isolates the Port from the MII with the exception of the serial management.
0 = Normal operation.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
79
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-3. Basic Mode Control Register (BMCR), address 0x00 (continued)
Bit
Bit Name
Default
9
RESTART
AUTO-NEGOTIATION
0, RW/SC
DUPLEX MODE
Strap, RW
Description
Restart Auto-Negotiation:
1 = Restart Auto-Negotiation. Re-initiates the Auto-Negotiation process. If AutoNegotiation is disabled (bit 12 = 0), this bit is ignored. This bit is self-clearing and will
return a value of 1 until Auto-Negotiation is initiated, whereupon it will self-clear.
Operation of the Auto-Negotiation process is not affected by the management entity
clearing this bit.
0 = Normal operation.
8
Duplex Mode:
When auto-negotiation is disabled writing to this bit allows the port Duplex capability to
be selected.
1 = Full Duplex operation.
0 = Half Duplex operation.
7
COLLISION TEST
0, RW
Collision Test:
1 = Collision test enabled.
0 = Normal operation.
When set, this bit will cause the COL signal to be asserted in response to the assertion
of TX_EN within 512-bit times. The COL signal will be de-asserted within 4-bit times in
response to the de-assertion of TX_EN.
6
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
5
UNIDIRECTIONAL
ENABLE
0, RW
Unidirectional Enable:
1 = Allow 100 Mb transmit activity independent of link status.
0 = Require link up for 100 Mb/s transmit activity.
This bit has no effect in 10 Mb/s mode..
4:0
RESERVED
0 0000, RO
RESERVED: Write ignored, read as 0.
10.1.2 Basic Mode Status Register (BMSR)
Table 10-4. Basic Mode Status Register (BMSR), address 0x01
Bit
Bit Name
Default
15
100BASE-T4
0, RO/P
14
100BASE-TX
1, RO/P
Description
100BASE-T4 Capable:
0 = Device not able to perform 100BASE-T4 mode.
FULL DUPLEX
13
100BASE-TX
1 = Device able to perform 100BASE-TX in full duplex mode.
1, RO/P
HALF DUPLEX
12
10BASE-T
10BASE-T
100BASE-TX Half Duplex Capable:
1 = Device able to perform 100BASE-TX in half duplex mode.
1, RO/P
FULL DUPLEX
11
100BASE-TX Full Duplex Capable:
10BASE-T Full Duplex Capable:
1 = Device able to perform 10BASE-T in full duplex mode.
1, RO/P
HALF DUPLEX
10BASE-T Half Duplex Capable:
1 = Device able to perform 10BASE-T in half duplex mode.
10:8
RESERVED
000, RO
RESERVED: Write as 0, read as 0.
7
UNIDIRECTIONAL
ABILITY
1, RO/P
Unidirectional Ability:
1 = Device able to transmit in 100 Mb/s mode independent of link status.
6
MF PREAMBLE
SUPPRESSION
1, RO/P
Preamble Suppression Capable:
AUTO-NEGOTIATION
COMPLETE
0, RO
1 = Device able to perform management transaction with preamble suppressed, 32-bits of
preamble needed only once after reset, invalid opcode or invalid turnaround.
0 = Normal management operation.
5
Auto-Negotiation Complete:
1 = Auto-Negotiation process complete.
0 = Auto-Negotiation process not complete.
80
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-4. Basic Mode Status Register (BMSR), address 0x01 (continued)
Bit
Bit Name
Default
4
REMOTE FAULT
0, RO/LH
Description
Remote Fault:
1 = Remote Fault condition detected (cleared on read or by reset). Fault criteria: Far End
Fault Indication or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected.
3
AUTO-NEGOTIATION
ABILITY
1, RO/P
Auto Negotiation Ability:
1 = Device is able to perform Auto-Negotiation.
0 = Device is not able to perform Auto-Negotiation.
2
LINK STATUS
0, RO/LL
Link Status:
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
The criteria for link validity is implementation specific. The occurrence of a link failure
condition will causes the Link Status bit to clear. Once cleared, this bit may only be set by
establishing a good link condition and a read via the management interface.
1
JABBER DETECT
0, RO/LH
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
1 = Jabber condition detected.
0 = No Jabber.
This bit is implemented with a latching function, such that the occurrence of a jabber
condition causes it to set until it is cleared by a read to this register by the management
interface or by a reset.
0
EXTENDED
CAPABILITY
1, RO/P
Extended Capability:
1 = Extended register capabilities.
0 = Basic register set capabilities only.
The PHY Identifier Registers #1 and #2 together form a unique identifier for the DP83630. The Identifier
consists of a concatenation of the Organizationally Unique Identifier (OUI), the vendor's model number
and the model revision number. A PHY may return a value of zero in each of the 32 bits of the PHY
Identifier if desired. The PHY Identifier is intended to support network management. TI's IEEE assigned
OUI is 080017h.
10.1.3 PHY Identifier Register #1 (PHYIDR1)
Table 10-5. PHY Identifier Register #1 (PHYIDR1), address 0x02
Bit
Bit Name
Default
15:0
OUI_MSB
0010 0000 0000 0000,
RO/P
Description
OUI Most Significant Bits: Bits 3 to 18 of the OUI (080017h) are stored in bits 15
to 0 of this register. The most significant two bits of the OUI are ignored (the IEEE
standard refers to these as bits 1 and 2).
10.1.4 PHY Identifier Register #2 (PHYIDR2)
Table 10-6. PHY Identifier Register #2 (PHYIDR2), address 0x03
Bit
Bit Name
Default
15:10
OUI_LSB
0101 11, RO/P
Description
OUI Least Significant Bits:
Bits 19 to 24 of the OUI (080017h) are mapped from bits 15 to 10 of this register
respectively.
9:4
VNDR_MDL
00 1110, RO/P
Vendor Model Number:
The six bits of vendor model number are mapped from bits 9 to 4 (most significant bit to
bit 9).
3:0
MDL_REV
0001, RO/P
Model Revision Number:
Four bits of the vendor model revision number are mapped from bits 3 to 0 (most
significant bit to bit 3). This field will be incremented for all major device changes.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
81
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.1.5 Auto-Negotiation Advertisement Register (ANAR)
This register contains the advertised abilities of this device as they will be transmitted to its link partner
during Auto-Negotiation. Any writes to this register prior to completion of Auto-Negotiation (as indicated in
the Basic Mode Status Register (address 01h) Auto-Negotiation Complete bit, BMSR[5]) should be
followed by a renegotiation. This will ensure that the new values are properly used in the Auto-Negotiation.
Table 10-7. Auto-Negotiation Advertisement Register (ANAR), address 0x04
Bit
Bit Name
Default
15
NP
0, RW
Description
Next Page Indication:
0 = Next Page Transfer not desired.
1 = Next Page Transfer desired.
14
RESERVED
0, RO/P
13
RF
0, RW
RESERVED by IEEE: Writes ignored, Read as 0.
Remote Fault:
1 = Advertises that this device has detected a Remote Fault.
0 = No Remote Fault detected.
12
RESERVED
0, RW
RESERVED for Future IEEE use: Write as 0, Read as 0
11
ASM_DIR
0, RW
Asymmetric PAUSE Support for Full Duplex Links:
The ASM_DIR bit indicates that asymmetric PAUSE is supported.
Encoding and resolution of PAUSE bits is defined in IEEE 802.3 Annex 28B, Tables
28B-2 and 28B-3, respectively. Pause resolution status is reported in PHYCR[13:12].
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control
sublayer and the pause function as specified in clause 31 and annex 31B of 802.3u.
0 = No MAC based full duplex flow control.
10
PAUSE
0, RW
PAUSE Support for Full Duplex Links:
The PAUSE bit indicates that the device is capable of providing the symmetric PAUSE
functions as defined in Annex 31B.
Encoding and resolution of PAUSE bits is defined in IEEE 802.3 Annex 28B, Tables
28B-2 and 28B-3, respectively. Pause resolution status is reported in PHYCR[13:12].
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control
sublayer and the pause function as specified in clause 31 and annex 31B of 802.3u.
0 = No MAC based full duplex flow control.
9
T4
0, RO/P
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the local device.
0 = 100BASE-T4 not supported.
8
TX_FD
Strap, RW
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the local device.
0 = 100BASE-TX Full Duplex not supported.
7
TX
Strap, RW
100BASE-TX Support:
1 = 100BASE-TX is supported by the local device.
0 = 100BASE-TX not supported.
6
10_FD
Strap, RW
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the local device.
0 = 10BASE-T Full Duplex not supported.
5
10
Strap, RW
10BASE-T Support:
1 = 10BASE-T is supported by the local device.
0 = 10BASE-T not supported.
4:0
SELECTOR
0 0001, RW
Protocol Selection Bits:
These bits contain the binary encoded protocol selector supported by this port. <00001>
indicates that this device supports IEEE 802.3u.
82
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The
content changes after the successful auto-negotiation if Next-pages are supported.
Table 10-8. Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page), address 0x05
Bit
Bit Name
Default
15
NP
0, RO
Description
Next Page Indication:
0 = Link Partner does not desire Next Page Transfer.
1 = Link Partner desires Next Page Transfer.
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word.
0 = Not acknowledged.
The Auto-Negotiation state machine will automatically control this bit based on the
incoming FLP bursts.
13
RF
0, RO
Remote Fault:
1 = Remote Fault indicated by Link Partner.
0 = No Remote Fault indicated by Link Partner.
12
RESERVED
0, RO
RESERVED for Future IEEE use: Write as 0, read as 0.
11
ASM_DIR
0, RO
ASYMMETRIC PAUSE:
1 = Asymmetric pause is supported by the Link Partner.
0 = Asymmetric pause is not supported by the Link Partner.
10
PAUSE
0, RO
PAUSE:
1 = Pause function is supported by the Link Partner.
0 = Pause function is not supported by the Link Partner.
9
T4
0, RO
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the Link Partner.
0 = 100BASE-T4 not supported by the Link Partner.
8
TX_FD
0, RO
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the Link Partner.
0 = 100BASE-TX Full Duplex not supported by the Link Partner.
7
TX
0, RO
100BASE-TX Support:
1 = 100BASE-TX is supported by the Link Partner.
0 = 100BASE-TX not supported by the Link Partner.
6
10_FD
0, RO
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the Link Partner.
0 = 10BASE-T Full Duplex not supported by the Link Partner.
5
10
0, RO
10BASE-T Support:
1 = 10BASE-T is supported by the Link Partner.
0 = 10BASE-T not supported by the Link Partner.
4:0
SELECTOR
0 0000, RO
Protocol Selection Bits:
Link Partner's binary encoded protocol selector.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
83
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.1.7 Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page)
Table 10-9. Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page), address 0x05
Bit
Bit Name
Default
15
NP
0, RO
Description
Next Page Indication:
1 = Link Partner desires Next Page Transfer.
0 = Link Partner does not desire Next Page Transfer.
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word.
0 = Not acknowledged.
The Auto-Negotiation state machine will automatically control this bit based on the
incoming FLP bursts. Software should not attempt to write to this bit.
13
MP
0, RO
Message Page:
1 = Message Page.
0 = Unformatted Page.
12
ACK2
0, RO
Acknowledge 2:
1 = Link Partner does have the ability to comply to next page message.
0 = Link Partner does not have the ability to comply to next page message.
11
TOGGLE
0, RO
Toggle:
1 = Previous value of the transmitted Link Code word equalled 0.
0 = Previous value of the transmitted Link Code word equalled 1.
10:0
CODE
000 0000 0000, RO
Code:
This field represents the code field of the next page transmission. If the MP bit is set
(bit 13 of this register), then the code shall be interpreted as a Message Page, as
defined in IEEE 802.3u Annex 28C of Clause 28. Otherwise, the code shall be
interpreted as an Unformatted Page, and the interpretation is application specific.
10.1.8 Auto-Negotiate Expansion Register (ANER)
This register contains additional Local Device and Link Partner status information.
Table 10-10. Auto-Negotiate Expansion Register (ANER), address 0x06
Bit
Bit Name
Default
15:5
RESERVED
0000 0000 000, RO
Description
4
PDF
0, RO
RESERVED: Writes ignored, Read as 0.
Parallel Detection Fault:
1 = A fault has been detected via the Parallel Detection function.
0 = A fault has not been detected.
3
LP_NP_ABLE
0, RO
Link Partner Next Page Able:
1 = Link Partner does support Next Page.
0 = Link Partner does not support Next Page.
2
NP_ABLE
1, RO/P
1
PAGE_RX
0, RO/COR
Next Page Able:
1 = Indicates local device is able to send additional Next Pages.
Link Code Word Page Received:
1 = Link Code Word has been received, cleared on a read.
0 = Link Code Word has not been received.
0
LP_AN_ABLE
0, RO
Link Partner Auto-Negotiation Able:
1 = Indicates that the Link Partner supports Auto-Negotiation.
0 = Indicates that the Link Partner does not support Auto-Negotiation.
84
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR)
This register contains the next page information sent by this device to its Link Partner during AutoNegotiation.
Table 10-11. Auto-Negotiation Next Page Transmit Register (ANNPTR), address 0x07
Bit
Bit Name
Default
15
NP
0, RW
Description
Next Page Indication:
0 = No other Next Page Transfer desired.
1 = Another Next Page desired.
14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
13
MP
1, RW
Message Page:
1 = Message Page.
0 = Unformatted Page.
12
ACK2
0, RW
Acknowledge2:
1 = Will comply with message.
0 = Cannot comply with message.
Acknowledge2 is used by the next page function to indicate that Local Device has
the ability to comply with the message received.
11
TOG_TX
0, RO
Toggle:
1 = Value of toggle bit in previously transmitted Link Code Word was 0.
0 = Value of toggle bit in previously transmitted Link Code Word was 1.
Toggle is used by the Arbitration function within Auto-Negotiation to ensure
synchronization with the Link Partner during Next Page exchange. This bit shall
always take the opposite value of the Toggle bit in the previously exchanged Link
Code Word.
10:0
CODE
000 0000 0001, RW
Code:
This field represents the code field of the next page transmission. If the MP bit is
set (bit 13 of this register), then the code shall be interpreted as a "Message
Page”, as defined in Annex 28C of IEEE 802.3u. Otherwise, the code shall be
interpreted as an "Unformatted Page”, and the interpretation is application
specific.
The default value of the CODE represents a Null Page as defined in Annex 28C
of IEEE 802.3u.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
85
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.1.10 PHY Status Register (PHYSTS)
This register provides a single location within the register set for quick access to commonly accessed
information.
Table 10-12. PHY Status Register (PHYSTS), address 0x10
Bit
Bit Name
Default
15
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
Description
14
MDIX MODE
0, RO
MDIX mode as reported by the Auto-Negotiation logic:
This bit will be affected by the settings of the MDIX_EN and FORCE_MDIX bits
in the PHYCR register. When MDIX is enabled, but not forced, this bit will
update dynamically as the Auto-MDIX algorithm swaps between MDI and MDIX
configurations.
1 = MDI pairs swapped
(Receive on TPTD pair, Transmit on TPRD pair)
0 = MDI pairs normal
(Receive on TPRD pair, Transmit on TPTD pair)
13
RECEIVE ERROR
LATCH
0, RO/LH
Receive Error Latch:
This bit will be cleared upon a read of the RECR register.
1 = Receive error event has occurred since last read of RXERCNT (address
15h, Page 0).
0 = No receive error event has occurred.
12
POLARITY STATUS
0, RO
Polarity Status:
This bit is a duplication of bit 4 in the 10BTSCR register. This bit will be cleared
upon a read of the 10BTSCR register, but not upon a read of the PHYSTS
register.
1 = Inverted Polarity detected.
0 = Correct Polarity detected.
11
FALSE CARRIER SENSE
LATCH
0, RO/LH
False Carrier Sense Latch:
This bit will be cleared upon a read of the FCSR register.
1 = False Carrier event has occurred since last read of FCSCR (address 14h).
0 = No False Carrier event has occurred.
10
SIGNAL DETECT
0, RO/LL
100Base-TX qualified Signal Detect from PMA:
This is the SD that goes into the link monitor. It is the AND of raw SD and
descrambler lock, when address 16h, bit 8 (page 0) is set. When bit 8 of
address 16h is cleared, it will be equivalent to the raw SD from the PMD.
9
DESCRAMBLER LOCK
0, RO/LL
8
PAGE RECEIVED
0, RO
100Base-TX Descrambler Lock from PMD.
Link Code Word Page Received:
This is a duplicate of the Page Received bit in the ANER register, but this bit
will not be cleared upon a read of the PHYSTS register.
1 = A new Link Code Word Page has been received. Cleared on read of the
ANER (address 06h, bit 1).
0 = Link Code Word Page has not been received.
7
MII INTERRUPT
0, RO
MII Interrupt Pending:
1 = Indicates that an internal interrupt is pending. Interrupt source can be
determined by reading the MISR Register (12h). Reading the MISR will clear
the Interrupt.
0 = No interrupt pending.
6
REMOTE FAULT
0, RO
Remote Fault:
1 = Remote Fault condition detected (cleared on read of BMSR (address 01h)
register or by reset). Fault criteria: notification from Link Partner of Remote
Fault via Auto-Negotiation.
0 = No remote fault condition detected.
86
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-12. PHY Status Register (PHYSTS), address 0x10 (continued)
Bit
Bit Name
Default
5
JABBER DETECT
0, RO
Description
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
This bit is a duplicate of the Jabber Detect bit in the BMSR register, except that
it is not cleared upon a read of the PHYSTS register.
1 = Jabber condition detected.
0 = No Jabber.
4
AUTO-NEG COMPLETE
0, RO
Auto-Negotiation Complete:
1 = Auto-Negotiation complete.
0 = Auto-Negotiation not complete.
3
LOOPBACK STATUS
0, RO
Loopback:
1 = Loopback enabled.
0 = Normal operation.
2
DUPLEX STATUS
0, RO
Duplex:
This bit indicates duplex status and is determined from Auto-Negotiation or
Forced Modes.
1 = Full duplex mode.
0 = Half duplex mode.
Note: This bit is only valid if Auto-Negotiation is enabled and complete and
there is a valid link or if Auto-Negotiation is disabled and there is a valid link.
1
SPEED STATUS
0, RO
Speed10:
This bit indicates the status of the speed and is determined from AutoNegotiation or Forced Modes.
1 = 10 Mb/s mode.
0 = 100 Mb/s mode.
Note: This bit is only valid if Auto-Negotiation is enabled and complete and
there is a valid link or if Auto-Negotiation is disabled and there is a valid link.
0
LINK STATUS
0, RO
Link Status:
This bit is a duplicate of the Link Status bit in the BMSR register, except that it
will not be cleared upon a read of the PHYSTS register.
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
87
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.1.11 MII Interrupt Control Register (MICR)
This register implements the MII Interrupt PHY Specific Control register. Sources for interrupt generation
include: Link Quality Monitor, Energy Detect State Change, Link State Change, Speed Status Change,
Duplex Status Change, Auto-Negotiation Complete or any of the counters becoming half-full. The
individual interrupt events must be enabled by setting bits in the MII Interrupt Status and Event Control
Register (MISR).
Table 10-13. MII Interrupt Control Register (MICR), address 0x11
Bit
Bit Name
Default
15:4
RESERVED
0000 0000 0000, RO
Description
3
PTP_INT_SEL
0, RW
PTP Interrupt Select:
Maps PTP Interrupt to the MISR register in place of the Duplex Interrupt. The
Duplex Interrupt will be combined with the Speed Interrupt.
1 = Map PTP Interrupt to MISR[11] , Speed/Duplex Interrupt to MISR[12]
0 = Map Duplex Interrupt to MISR[11], Speed Interrupt to MISR[12]
2
TINT
0, RW
Test Interrupt:
RESERVED: Writes ignored, read as 0.
Forces the PHY to generate an interrupt to facilitate interrupt testing. Interrupts will
continue to be generated as long as this bit remains set.
1 = Generate an interrupt.
0 = Do not generate interrupt.
1
INTEN
0, RW
Interrupt Enable:
Enable interrupt dependent on the event enables in the MISR register.
1 = Enable event based interrupts.
0 = Disable event based interrupts.
0
INT_OE
0, RW
Interrupt Output Enable:
Enable interrupt events to signal via the PWRDOWN/INTN pin by configuring the
PWRDOWN/INTN pin as an output.
1 = PWRDOWN/INTN is an Interrupt Output.
0 = PWRDOWN/INTN is a Power Down Input.
88
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.1.12 MII Interrupt Status and Event Control Register (MISR)
This register contains event status and enables for the interrupt function. If an event has occurred since
the last read of this register, the corresponding status bit will be set. If the corresponding enable bit in the
register is set, an interrupt will be generated if the event occurs. The MICR register controls must also be
set to allow interrupts. The status indications in this register will be set even if the interrupt is not enabled.
Table 10-14. MII Interrupt Status and Event Control Register (MISR), address 0x12
Bit
Bit Name
Default
15
LQ_INT
0, RO/COR
Description
Link Quality Interrupt:
1 = Link Quality interrupt is pending and is cleared by the current read.
0 = No Link Quality interrupt pending.
14
ED_INT
0, RO/COR
Energy Detect Interrupt:
1 = Energy detect interrupt is pending and is cleared by the current read.
0 = No energy detect interrupt pending.
13
LINK_INT
0, RO/COR
Change of Link Status Interrupt:
1 = Change of link status interrupt is pending and is cleared by the current read.
0 = No change of link status interrupt pending.
12
SPD_INT
or
SPD_DUP_INT
0, RO/COR
Change of Speed Status Interrupt:
Change of speed status interrupt. This function is selected if MICR[3] is set to 0.
1 = Speed status change interrupt is pending and is cleared by the current read.
0 = No speed status change interrupt pending.
Change of Speed/Duplex Interrupt:
Change of speed or duplex status interrupt. This function is selected if MICR[3] is
set to 1.
1 = Speed/duplex status change interrupt is pending and is cleared by the current
read.
0 = No speed/duplex status change interrupt pending.
11
DUP_INT
or
PTP_INT
0, RO/COR
Change of Duplex Status Interrupt:
Change of duplex status interrupt. This function is selected if MICR[3] is set to 0.
1 = Duplex status change interrupt is pending and is cleared by the current read.
0 = No duplex status change interrupt pending.
PTP Interrupt:
PTP interrupt. This function is selected if MICR[3] is set to 1. PTP interrupt status
should be read from the PTP_STS register. This interrupt will not be rearmed until
the PTP_STS register indicates no further PTP status is available.
1 = PTP interrupt is pending and is cleared by the current read.
0 = No PTP interrupt pending.
10
ANC_INT
0, RO/COR
Auto-Negotiation Complete Interrupt:
1 = Auto-negotiation complete interrupt is pending and is cleared by the current
read.
0 = No Auto-negotiation complete interrupt pending.
9
FHF_INT
or
CTR_INT
0, RO/COR
False Carrier Counter Half-Full Interrupt:
False carrier counter half-full interrupt. This function is selected if the PHYCR2[8:7]
are both 0.
1 = False carrier counter half-full interrupt is pending and is cleared by the current
read.
0 = No false carrier counter half-full interrupt pending.
CTR Interrupt:
False carrier or Receive Error counter half-full interrupt. This function is selected if
either of PHYCR2[8:7] are set.
1 = False carrier or receive error counter half-full interrupt is pending and is cleared
by the current read.
0 = No false carrier or receive error counter half-full interrupt pending.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
89
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-14. MII Interrupt Status and Event Control Register (MISR), address 0x12 (continued)
Bit
Bit Name
Default
Description
8
RHF_INT
or
PCF_INT
0, RO/COR
Receive Error Counter half-full interrupt:
Receive error counter half-full interrupt. This function is selected if the
PHYCR2[8:7] are both 0.
1 = Receive error counter half-full interrupt is pending and is cleared by the current
read.
0 = No receive error carrier counter half-full interrupt pending.
PCF Interrupt:
PHY Control Frame interrupt. This function is selected if either of PHYCR2[8:7] are
set.
1 = PHY Control Frame interrupt is pending and is cleared by the current read.
0 = No PHY Control Frame interrupt pending.
7
LQ_INT_EN
0, RW
Enable Interrupt on Link Quality Monitor event.
6
ED_INT_EN
0, RW
Enable Interrupt on energy detect event.
5
LINK_INT_EN
0, RW
Enable Interrupt on change of link status.
4
SPD_INT_EN
0, RW
Enable Interrupt on change of speed status.
3
DUP_INT_EN
or
PTP_INT_EN
0, RW
Duplex Interrupt:
Enable Interrupt on change of duplex status. This function is selected if MICR[3] is
set to 0.
PTP Interrupt:
PTP interrupt. This function is selected if MICR[3] is set to 1.
2
ANC_INT_EN
0, RW
Enable Interrupt on auto-negotiation complete event.
1
FHF_INT_EN
or
CTR_INT_EN
0, RW
FHF Interrupt:
Enable Interrupt on False Carrier Counter Register halffull event. This function is
selected if the PHYCR2[8:7] are both 0.
CTR Interrupt:
Enable interrupt on either Receive Error Counter Register half-full event or False
Carrier Counter Register half-full event. This function is selected if either of
PCFCR[7:6] are set.
0
RHF_INT_EN
or
PCF_INT_EN
0, RW
RHF Interrupt:
Enable Interrupt on Receive Error Counter Register halffull event. This function is
selected if the PHYCR2[8:7] are both 0.
PCF Interrupt:
Enable Interrupt on a PHY Control Frame event. This function is selected if either
of PCFCR[7:6] are set.
10.1.13 Page Select Register (PAGESEL)
This register is used to enable access to the Link Diagnostics Registers.
Table 10-15. Page Select Register (PAGESEL), address 0x13
Bit
Bit Name
Default
15:3
RESERVED
0000 0000 0000 0,
RO
2:0
PAGE_SEL
000, RW
90
Description
RESERVED: Writes ignored, read as 0
Page_Sel Bits:
Selects between paged registers for address 14h to 1Fh.
0 = Extended Registers Page 0
1 = RESERVED
2 = Link Diagnostics Registers Page 2
3 = RESERVED
4 = PTP 1588 Base Registers Page 4
5 = PTP 1588 Config Registers Page 5
6 = PTP 1588 Config Registers Page 6
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.2 EXTENDED REGISTERS - PAGE 0
10.2.1 False Carrier Sense Counter Register (FCSCR)
This counter provides information required to implement the “False Carriers” attribute within the MAU
managed object class of Clause 30 of the IEEE 802.3u specification.
Table 10-16. False Carrier Sense Counter Register (FCSCR), address 0x14
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
Description
7:0
FCSCNT[7:0]
0000 0000, RO/COR
RESERVED: Writes ignored, read as 0
False Carrier Event Counter:
This 8-bit counter increments on every false carrier event. This counter sticks when
it reaches its maximum count (FFh).
10.2.2 Receiver Error Counter Register (RECR)
This counter provides information required to implement the “Symbol Error During Carrier” attribute within
the PHY managed object class of Clause 30 of the IEEE 802.3u specification.
Table 10-17. Receiver Error Counter Register (RECR), address 0x15
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
Description
7:0
RXERCNT[7:0]
0000 0000, RO/COR
RESERVED: Writes ignored, read as 0.
RX_ER Counter:
When a valid carrier is present and there is at least one occurrence of an invalid
data symbol, this 8-bit counter increments for each receive error detected. This
event can increment only once per valid carrier event. If a collision is present, the
attribute will not increment. The counter sticks when it reaches its maximum count.
10.2.3 100 Mb/s PCS Configuration and Status Register (PCSR)
This register contains control and status information for the 100BASE Physical Coding Sublayer.
Table 10-18. 100 Mb/s PCS Configuration and Status Register (PCSR), address 0x16
Bit
Bit Name
Default
15
AUTO_CROSSOV
ER
0, RW
14:12
RESERVED
000, RW
11
FREE_CLK
0, RW
Description
Auto-Crossover in Forced Mode:
1 = Auto-Crossover in Forced Mode Enabled
Allows the device to toggle between MDIX and MDI channels when forced to 10M or
100M mode. This function is mutually exclusive with the Auto-Negotiation Enable bit,
BMCR[12], and with the Auto-MDIX Enable bit, PHYCR[15]. These bits should not
be set when enabling Auto-crossover.
0 = Normal operation
RESERVED: Must be 0.
Receive Clock:
1 = RX_CLK is free-running.
0 = RX_CLK phase adjusted based on alignment.
10
TQ_EN
0, RW
100 Mb/s True Quiet Mode Enable:
1 = Transmit True Quiet Mode.
0 = Normal Transmit Mode.
9
SD FORCE PMA
0, RW
Signal Detect Force PMA:
1 = Forces Signal Detection in PMA.
0 = Normal SD operation.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
91
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-18. 100 Mb/s PCS Configuration and Status Register (PCSR), address 0x16 (continued)
Bit
Bit Name
Default
8
SD_OPTION
1, RW
Description
Signal Detect Option:
1 = Default operation. Link will be asserted following detection of valid signal level
and Descrambler Lock. Link will be maintained as long as signal level is valid. A loss
of Descrambler Lock will not cause Link Status to drop.
0 = Modified signal detect algorithm. Link will be asserted following detection of valid
signal level and Descrambler Lock. Link will be maintained as long as signal level is
valid and Descrambler remains locked.
7
DESC_TIME
0, RW
Descrambler Timeout:
Increase the descrambler timeout. When set, this allows the device to receive larger
packets (>9k bytes) without loss of synchronization.
1 = 2 ms.
0 = 722 µs (per ANSI X3.263: 1995 (TP-PMD) 7.2.3.3e).
6
FX_EN
Strap, RW
FX Fiber Mode Enable:
This bit is set when the FX_EN strap option is selected for the respective port.
Write PHYCR2[9], SOFT_RESET, after enabling or disabling Fiber Mode via register
access to ensure correct configuration.
1 = Enables FX operation.
0 = Disables FX operation.
5
FORCE_100_OK
0, RW
Force 100 Mb/s Good Link:
OR’ed with MAC_FORCE_LINK_100 signal.
1 = Forces 100 Mb/s Good Link.
0 = Normal 100 Mb/s operation.
4
RESERVED
0, RO
3
FEFI_EN
Strap, RW
RESERVED: Writes ignored, read as 0.
Far End Fault Indication Mode Enable:
This bit is set when the FX_EN strap option is selected for the respective port.
1 = FEFI Mode Enabled.
0 = FEFI Mode Disabled.
2
NRZI_BYPASS
0, RW
NRZI Bypass Enable:
1 = NRZI Bypass Enabled.
0 = NRZI Bypass Disabled.
1
SCRAM
BYPASS
Strap, RW
Scrambler Bypass Enable:
This bit is set when the FX_EN strap option is selected. In the FX mode, the
scrambler is bypassed.
1 = Scrambler Bypass Enabled.
0 = Scrambler Bypass Disabled.
0
DESCRAM
BYPASS
Strap, RW
Descrambler Bypass Enable:
This bit is set when the FX_EN strap option is selected. In the FX mode, the
descrambler is bypassed.
1 = Descrambler Bypass Enabled.
0 = Descrambler Bypass Disabled.
92
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.2.4 RMII and Bypass Register (RBR)
This register configures the RMII/MII Interface Mode of operation. This register controls selecting MII,
RMII, or Single Clock MII mode for Receive or Transmit. In addition, several additional bits are included to
allow datapath selection for Transmit and Receive in multiport applications.
Table 10-19. RMII and Bypass Register (RBR), address 0x17
Bit
Bit Name
Default
15
RESERVED
0, RW
14
RMII_MASTER
Strap, RW
13
DIS_TX_OPT
0, RW
Description
RESERVED: Must be 0.
RMII Master Mode:
Setting this bit allows the core to use a 25 MHz input reference clock and generate
its own 50 MHz RMII reference clock. The generated RMII reference clock will also
be used by the attached MAC.
1 = RMII Master Mode (25 MHz input reference)
0 = RMII Slave Mode (50 MHz input reference)
Note: Due to clock muxing and divider operation, this bit should normally only be
reconfigured via the strap option.
Disable RMII TX Latency Optimization:
Normally the RMII Transmitter will minimize the transmit latency by realigning the
transmit clock with the reference clock phase at the start of a packet transmission.
Setting this bit will disable phase realignment and ensure that IDLE bits will always
be sent in multiples of the symbol size. This will result in a larger uncertainty in
RMII transmit latency.
12:9
RESERVED
0000, RW
8
PMD_LOOP
0, RW
RESERVED: Must be 0.
PMD Loopback:
0 = Normal Operation.
1 = Remote (PMD) Loopback.
Setting this bit will cause the device to Loopback data received from the Physical
Layer. The loopback is done prior to the MII or RMII interface. Data received at the
internal MII or RMII interface will be applied to the transmitter. This mode should
only be used if RMII mode or Single Clock MII mode is enabled.
7
SCMII_RX
0, RW
Single Clock RX MII Mode:
0 = Standard MII mode.
1 = Single Clock RX MII Mode.
Setting this bit will cause the device to generate receive data (RX_DV, RX_ER,
RXD[3:0]) synchronous to the X1 Reference clock. RX_CLK is not used in this
mode. This mode uses the RMII elasticity buffer to tolerate variations in clock
frequencies. This bit cannot be set if RMII_MODE is set to a 1.
6
SCMII_TX
0, RW
Single Clock TX MII Mode:
0 = Standard MII mode.
1 = Single Clock TX MII Mode.
Setting this bit will cause the device to sample transmit data (TX_EN, TXD[3:0])
synchronous to the X1 Reference clock. TX_CLK is not used in this mode. This bit
cannot be set if RMII_MODE is set to a 1.
5
RMII_MODE
Strap, RW
Reduced MII Mode:
0 = Standard MII Mode.
1 = Reduced MII Mode.
4
RMII_REV1_0
0, RW
Reduced MII Revision 1.0:
This bit modifies how CRS_DV is generated.
0 = (RMII revision 1.2) CRS_DV will toggle at the end of a packet to indicate
deassertion of CRS.
1 = (RMII revision 1.0) CRS_DV will remain asserted until final data is transferred.
CRS_DV will not toggle at the end of a packet.
3
RX_OVF_STS
0, RO
RX FIFO Over Flow Status:
0 = Normal.
1 = Overflow detected.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
93
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-19. RMII and Bypass Register (RBR), address 0x17 (continued)
Bit
Bit Name
Default
2
RX_UNF_STS
0, RO
Description
RX FIFO Under Flow Status:
0 = Normal.
1 = Underflow detected.
1:0
ELAST_BUF[1:0]
01, RW
Receive Elasticity Buffer:
This field controls the Receive Elasticity Buffer which allows for frequency variation
tolerance between the 50 MHz RMII clock and the recovered data. See Reduced
MII Interface for more information on Elasticity Buffer settings in RMII mode. See
Section Single Clock MII Mode for more information on Elasticity Buffer settings in
SCMII mode.
10.2.5 LED Direct Control Register (LEDCR)
This register provides the ability to directly control any or all LED outputs. It does not provide read access
to LEDs. In addition, it provides control for the Activity source and blinking LED frequency.
Table 10-20. LED Direct Control Register (LEDCR), address 0x18
Bit
Bit Name
Default
15:12
RESERVED
0000, RO
Description
11
DIS_SPDLED
0, RW
1 = Disable LED_SPEED output
0 = Enable LED_SPEED output
10
DIS_LNKLED
0, RW
1 = Disable LED_LINK output
0 = Enable LED_LINK output
9
DIS_ACTLED
0, RW
1 = Disable LED_ACT output
0 = Enable LED_ACT output
8
LEDACT_RX
0, RW
1 = Activity is only indicated for Receive traffic
RESERVED: Writes ignored, read as 0.
0 = Activity is indicated for Transmit or Receive traffic
7:6
BLINK_FREQ
00, RW
LED Blink Frequency:
These bits control the blink frequency of the LED_LINK output when blinking on
activity is enabled.
0 = 6 Hz
1 = 12 Hz
2 = 24 Hz
3 = 48 Hz
5
DRV_SPDLED
0, RW
4
DRV_LNKLED
0, RW
3
DRV_ACTLED
0, RW
1 = Drive value of SPDLED bit onto LED_SPEED output
0 = Normal operation
1 = Drive value of LNKLED bit onto LED_LINK output
0 = Normal operation
1 = Drive value of ACTLED bit onto LED_ACT output
0 = Normal operation
94
2
SPDLED
0, RW
Value to force on LED_SPEED output
1
LNKLED
0, RW
Value to force on LED_LINK output
0
ACTLED
0, RW
Value to force on LED_ACT output
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.2.6 PHY Control Register (PHYCR)
This register provides control for PHY functions such as MDIX, BIST, LED configuration, and PHY
address. It also provides Pause Negotiation status.
Table 10-21. PHY Control Register (PHYCR), address 0x19
Bit
Bit Name
Default
15
MDIX_EN
1, RW
Description
Auto-MDIX Enable:
1 = Enable Auto-neg Auto-MDIX capability.
0 = Disable Auto-neg Auto-MDIX capability.
14
FORCE_MDIX
0, RW
Force MDIX:
1 = Force MDI pairs to cross.
(Receive on TD pair, Transmit on RD pair)
0 = Normal operation.
13
PAUSE_RX
0, RO
Pause Receive Negotiated:
Indicates that pause receive should be enabled in the MAC. Based on ANAR[11:10]
and ANLPAR[11:10] settings.
This function shall be enabled according to IEEE 802.3 Annex 28B Table 28B-3,
“Pause Resolution”, only if the Auto-Negotiated Highest Common Denominator is a
full duplex technology.
12
PAUSE_TX
0, RO
Pause Transmit Negotiated:
Indicates that pause transmit should be enabled in the MAC. Based on ANAR[11:10]
and ANLPAR[11:10] settings.
This function shall be enabled according to IEEE 802.3 Annex 28B Table 28B-3,
Pause Resolution, only if the Auto-Negotiated Highest Common Denominator is a
full duplex technology.
11
BIST_FE
0, RW/SC
BIST Force Error:
1 = Force BIST Error.
0 = Normal operation.
This bit forces a single error, and is self clearing.
10
PSR_15
0, RW
BIST Sequence select:
1 = PSR15 selected.
0 = PSR9 selected.
9
BIST_STATUS
0, LL/RO
BIST Test Status:
1 = BIST pass.
0 = BIST fail. Latched, cleared when a BIST failure occurs or BIST is stopped.
For a count number of BIST errors, see the BIST Error Count in the CDCTRL1
Register.
8
BIST_START
0, RW
BIST Start:
Writes:
1 = BIST start. Writing 1 to this bit enables transmission of BIST packets and
enables the receive BIST engine to start looking for packet traffic.
0 = BIST stop. Stop the BIST. Writing 0 to this bit also clears the BIST_STATUS bit.
Reads:
1 = BIST active. This bit reads 1 after the transmit BIST engine has been enabled
and the receive BIST engine has detected packet traffic.
0 = BIST inactive. This bit will read 0 if the BIST is disabled or if the BIST is enabled
but no receive traffic has been detected.
7
BP_STRETCH
0, RW
Bypass LED Stretching:
This will bypass the LED stretching and the LEDs will reflect the internal value.
1 = Bypass LED stretching.
0 = Normal operation.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
95
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-21. PHY Control Register (PHYCR), address 0x19 (continued)
Bit
Bit Name
Default
6
5
LED_CNFG[1]
LED_CNFG[0]
0, RW
Strap, RW
Description
LED Configuration
LED_CNFG[1]
LED_CNFG[0]
Mode Description
Don't care
1
Mode 1
0
0
Mode 2
1
0
Mode 3
In Mode 1, LEDs are configured as follows:
LED_LINK = ON for Good Link, OFF for No Link
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT = ON for Activity, OFF for No Activity
In Mode 2, LEDs are configured as follows:
LED_LINK = ON for Good Link, BLINK for Activity
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT = ON for Collision, OFF for No Collision
In Mode 3, LEDs are configured as follows:
LED_LINK = ON for Good Link, BLINK for Activity
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT = ON for Full Duplex, OFF for Half Duplex
4:0
96
PHYADDR[4:0]
Strap, RW
PHY Address: PHY address for port.
Note: The local PHY address cannot be changed via a broadcast write - writing to
PHY address 0x1F register 0x19 will not change the PHYADDR bits.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.2.7 10Base-T Status/Control Register (10BTSCR)
This register is used for control and status for 10BASE-T device operation.
Table 10-22. 10Base-T Status/Control Register (10BTSCR), address 0x1A
Bit
Bit Name
Default
15
RESERVED
0, RO
Description
14:12
RESERVED
000, RW
RESERVED: Must be zero.
11:9
SQUELCH
100, RW
Squelch Configuration:
Used to set the Squelch 'ON' threshold for the receiver.
Default Squelch 'ON' is 330mV peak.
RESERVED: Writes ignored, read as 0.
10Base-T Loopback Disable:
8
LOOPBACK_10_DIS
0, RW
This bit is OR’ed with bit 14 (Loopback) in the BMCR.
1 = 10BT Loopback is disabled
0 = 10BT Loopback is enabled
Normal Link Pulse Disable:
This bit is OR’ed with the MAC_FORCE_LINK_10 signal.
7
LP_DIS
0, RW
1 = Transmission of NLPs is disabled.
0 = Transmission of NLPs is enabled.
Force 10 Mb Good Link:
This bit is OR’ed with the MAC_FORCE_LINK_10 signal.
6
FORCE_LINK_10
0, RW
1 = Forced Good 10 Mb Link.
0 = Normal Link Status.
5
FORCE_POL COR
0, RW
Force 10 Mb Polarity Correction:
1 = Force inverted polarity
0 = Normal polarity
10 Mb Polarity Status:
4
POLARITY
0, RO/LH
This bit is a duplication of bit 12 in the PHYSTS register. Both bits will be cleared
upon a read of either register.
1 = Inverted Polarity detected.
0 = Correct Polarity detected.
3
AUTOPOL_DIS
0, RW
Auto Polarity Detection & Correction Disable:
1 = Polarity Correction disabled
0 = Polarity Correction enabled
2
10BT_SCALE - MSB
1, RW
10BT Scale Configuration Most Significant Bit
Used in conjunction with bit 10 of SD_CNFG register to set the silence ’OFF’
threshold for the receiver.
Heartbeat Disable:
This bit only has influence in half-duplex 10 Mb mode.
1
HEARTBEAT_DIS
0, RW
1 = Heartbeat function disabled.
0 = Heartbeat function enabled.
When the device is operating at 100 Mb or configured for full duplex
operation, this bit will be ignored - the heartbeat function is disabled.
Jabber Disable:
0
JABBER_DIS
0, RW
This bit is only applicable in 10BASE-T.
1 = Jabber function disabled.
0 = Jabber function enabled.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
97
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.2.8 CD Test and BIST Extensions Register (CDCTRL1)
This register controls test modes for the 10BASE-T Common Driver. In addition it contains extended
control and status for the packet BIST function.
Table 10-23. CD Test and BIST Extensions Register (CDCTRL1), address 0x1B
Bit
Bit Name
Default
15:8
BIST_ERROR_COUNT
0000 0000, RO
Description
BIST ERROR Counter:
Counts number of errored data nibbles during Packet BIST. This value
will reset when Packet BIST is restarted. The counter sticks when it
reaches its maximum count of FFh.
7
RESERVED
0, RW
RESERVED: Must be 0.
6
MII_CLOCK_EN
0, RW
Enables MII Clocks TX_CLK and RX_CLK independent of MAC interface
mode selected; for example, normally TX_CLK and RX_CLK are
disabled in RMII Slave mode.
1 = Enable TX_CLK and RX_CLK
0 = Default operation
5
BIST_CONT
0, RW
Packet BIST Continuous Mode:
Allows continuous pseudorandom data transmission without any break in
transmission. This can be used for transmit VOD testing. This is used in
conjunction with the BIST controls in the PHYCR Register (19h). For 10
Mb operation, jabber function must be disabled, bit 0 of the 10BTSCR
(1Ah), JABBER_DIS = 1.
4
CDPATTEN_10
0, RW
CD Pattern Enable for 10 Mb:
1 = Enabled.
0 = Disabled.
3
MDIO_PULL_EN
0, RW
Enable Internal MDIO Pullup:
1 = Internal MDIO pullup enabled
0 = Internal MDIO pullup disabled
This bit is only reset on hard reset. This bit should not be set in systems
that share the management interfaces among several ASICs.
2
PATT_GAP_10M
0, RW
Defines gap between data or NLP test sequences:
1 = 15 µs.
0 = 10 µs.
1:0
CDPATTSEL[1:0]
00, RW
CD Pattern Select[1:0]:
If CDPATTEN_10 = 1:
00 = Data, EOP0 sequence.
01 = Data, EOP1 sequence.
10 = NLPs.
11 = Constant Manchester 1s (10 MHz sine wave) for harmonic distortion
testing.
98
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.2.9 PHY Control Register 2 (PHYCR2)
This register provides additional general control.
Table 10-24. PHY Control Register 2 (PHYCR2), address 0x1C
Bit
Bit Name
Default
15:14
RESERVED
00, RO
RESERVED: Writes ignored, read as 0.
Description
13
SYNC_ENET EN
0, RW
Synchronous Ethernet Enable:
When this bit is 1 and the device is in 100 Mb/s mode, and the MAC
interface is either MII or RMII Master, enables fully synchronous
communication relative to the recovered receive clock. The transmitter is
synchronized to the receiver.
When this bit is 0 or the device settings do not match the above
conditions, the transmitter is synchronous to the local reference clock.
12
CLK_OUT RXCLK
0, RW
Enable RX_CLK on CLK_OUT:
When this bit is 1 and the device is in 100 Mb/s mode, the 25 MHz
recovered receive clock (RX_CLK) is driven on CLK_OUT in addition to
RX_CLK. When this bit is 0 or the device is in 10 Mb/s mode, CLK_OUT
reflects the Reference clock.
11
BC_WRITE
0, RW
Broadcast Write Enable:
1 = Enables the Serial Management Interface to accept register writes to
PHY Address of 0x1F independent of the local PHY Address value.
0 = Normal operation
10
PHYTER_COMP
0, RW
Phyter Compatibility Mode:
1 = Enables Phyter (DP83848) Compatible pinout. Reorders the RX MII
pins and Autonegotiation straps to match the DP83848. Also enables the
CLK_OUT output.
0 = Normal operation
9
SOFT_RESET
0, RW/SC
Soft Reset:
Resets the entire device minus the registers - all configuration is
preserved.
1 = Reset, self-clearing.
8:2
RESERVED
0 0000 00, RO
1
CLK_OUT_DIS
Strap, RW
0
RESERVED
0, RW
RESERVED: Writes ignored, read as 0.
Disable CLK_OUT Output:
Disables the CLK_OUT output pin.
RESERVED: Must be zero.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
99
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.2.10 Energy Detect Control (EDCR)
This register provides control and status for the Energy Detect function.
Table 10-25. Energy Detect Control (EDCR), address 0x1D
Bit
Bit Name
Default
15
ED_EN
0, RW
Description
Energy Detect Enable:
Allow Energy Detect Mode.
14
ED_AUTO_UP
1, RW
Energy Detect Automatic Power Up:
Automatically begin power up sequence when Energy Detect Data
Threshold value (EDCR[3:0]) is reached. Alternatively, the device could
be powered up manually using the ED_MAN bit (ECDR[12]).
13
ED_AUTO_DOWN
1, RW
Energy Detect Automatic Power Down:
Automatically begin power down sequence when no energy is detected.
Alternatively, the device could be powered down using the ED_MAN bit
(EDCR[12]).
12
ED_MAN
0, RW/SC
Energy Detect Manual Power Up/Down:
Begin power up/down sequence when this bit is asserted. When set, the
Energy Detect algorithm will initiate a change of Energy Detect state
regardless of threshold (error or data) and timer values. In managed
applications, this bit can be set after clearing the Energy Detect interrupt
to control the timing of changing the power state.
11
ED_BURST_DIS
0, RW
Energy Detect Burst Disable:
Disable bursting of energy detect data pulses. By default, Energy Detect
(ED) transmits a burst of 4 ED data pulses each time the CD is powered
up. When bursting is disabled, only a single ED data pulse will be sent
each time the CD is powered up.
10
ED_PWR_STATE
0, RO
Energy Detect Power State:
Indicates current Energy Detect Power state. When set, Energy Detect is
in the powered up state. When cleared, Energy Detect is in the powered
down state. This bit is invalid when Energy Detect is not enabled.
9
ED_ERR_MET
0, RO/COR
Energy Detect Error Threshold Met:
No action is automatically taken upon receipt of error events. This bit is
informational only and would be cleared on a read.
8
ED_DATA_MET
0, RO/COR
Energy Detect Data Threshold Met:
The number of data events that occurred met or surpassed the Energy
Detect Data Threshold. This bit is cleared on a read.
7:4
ED_ERR_COUNT
0001, RW
Energy Detect Error Threshold:
Threshold to determine the number of energy detect error events that
should cause the device to take action. Intended to allow averaging of
noise that may be on the line. Counter will reset after approximately 2
seconds without any energy detect data events.
3:0
ED_DATA_COUNT
0001, RW
Energy Detect Data Threshold:
Threshold to determine the number of energy detect events that should
cause the device to take actions. Intended to allow averaging of noise
that may be on the line. Counter will reset after approximately 2 seconds
without any energy detect data events.
100
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.2.11 PHY Control Frames Configuration Register (PCFCR)
This register provides configuration for the PHY Control Frame mechanism for register access.
Table 10-26. PHY Control Frames Configuration Register (PCFCR), address 0x1F
Bit
Bit Name
Default
15
PCF_STS_ERR
0, RO/COR
Description
PHY Control Frame Error Detected:
Indicates an error was detected in a PCF Frame since the last read of
this register. This bit will be cleared on read.
14
PCF_STS_OK
0, RO/COR
PHY Control Frame OK:
Indicates a PCF Frame has completed without error since the last read
of this register. This bit will be cleared on read.
13:9
RESERVED
00 000, RO
8
PCF_DA_SEL
0, RW
Reserved: Writes ignored, read as 0
Select MAC Destination Address for PHY Control Frames:
0 : Use MAC Address [08 00 17 0B 6B 0F]
1 : Use MAC Address [08 00 17 00 00 00]
The device will also recognize packets with the above address with the
Multicast bit set (i.e. 09 00 17 ...).
7:6
PCF_INT_CTL
00, RW
PHY Control Frame Interrupt Control:
Setting either of these bits enables control and status of the PCF
Interrupt through the MISR Register (taking the place of the RHF
Interrupt).
00 = PCF Interrupts Disabled
x1 = Interrupt on PCF Frame OK
1x = Interrupt on PCF Frame Error
5
PCF_BC_DIS
0, RW
PHY Control Frame Broadcast Disable:
By default, the device will accept broadcast PHY Control Frames which
have a PHY Address field of 0x1F. If this bit is set to a 1, the PHY
Control Frame must have a PHY Address field that exactly matches the
device PHY Address.
4:1
PCF_BUF
0 000, RW
PHY Control Frame Buffer Size:
Determines the buffer size for transmit to allow PHY Control Frame
detection. All packets will be delayed as they pass through this buffer. If
set to 0, packets will not be delayed and PHY Control frames will be
truncated after the Destination Address field.
0
PCF_EN
Strap, RW
PHY Control Frame Enable:
Enables Register writes using PHY Control Frames.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
101
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.3 TEST REGISTERS - PAGE 1
Page 1 Test Registers are accessible by setting bits [2:0] = 001 of PAGESEL (13h).
10.3.1 Signal Detect Configuration (SD_CNFG), Page 1
This register contains Signal Detect configuration control as well as some test controls to speed up Autoneg testing.
Table 10-27. Signal Detect Configuration (SD_CNFG), address 0x1E
102
Bit
Bit Name
Default
15
RESERVED
1, RW
RESERVED: Write as 1, read as 1.
14:12
RESERVED
000, RW
RESERVED: Write as 0, read as 0.
11
RESERVED
0, RO
10:9
RESERVED
00, RW
RESERVED: Write as 0, read as 0.
0, RW
Signal Detect Time
Setting this bit to a 1 enables a fast detection of loss of Signal
Detect. This will result in a fast loss of Link indication. Approximate
times to detect signal detect deassertion are:
1 = 1 µs
0 = 250 µs
8
SD_TIME
7:0
RESERVED
Description
RESERVED: Write ignored, read as 0.
0000 0000, RW RESERVED: Write as 0, read as 0.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.4 LINK DIAGNOSTICS REGISTERS - PAGE 2
Page 2 Link Diagnostics Registers are accessible by setting bits [2:0] = 010 of PAGESEL (13h).
10.4.1 100 Mb Length Detect Register (LEN100_DET), Page 2
This register contains linked cable length estimation in 100 Mb operation. The cable length is an
estimation of the effective cable length based on the characteristics of the recovered signal. The cable
length is valid only during 100 Mb operation with a valid Link status indication.
Table 10-28. 100 Mb Length Detect Register (LEN100_DET), address 0x14
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
RESERVED: Writes ignored, read as 0.
Description
7:0
CABLE_LEN
1111 1111, RO
Cable Length Estimate:
Indicates an estimate of effective cable length in meters. A value of FFh
indicates cable length cannot be determined.
10.4.2 100 Mb Frequency Offset Indication Register (FREQ100), Page 2
This register returns an indication of clock frequency offset relative to the link partner. Two values can be
read, the long term Frequency Offset, or a short term Frequency Control value. The Frequency Control
value includes short term phase correction. The variance between the Frequency Control value and the
Frequency Offset can be used as an indication of the amount of jitter in the system.
Table 10-29. 100 Mb Frequency Offset Indication Register (FREQ100), address 0x15
Bit
Bit Name
Default
15
SAMPLE_FREQ
0, WO
Description
Sample Frequency Offset:
If SEL_FC is set to a 0, then setting this bit to a 1 will poll the DSP for
the long-term Frequency Offset value. The value will be available in
the FREQ_OFFSET bits of this register.
If SEL_FC is set to a 1, then setting this bit to a 1 will poll the DSP for
the current Frequency Control value. The value will be available in the
FREQ_OFFSET bits of this register.
This register bit will always read back as 0.
14:9
RESERVED
000 000, RO
8
SEL_FC
0, RW
RESERVED: Writes ignored, read as 0.
Select Frequency Control:
Setting this bit to a 1 will select the current Frequency Control value
instead of the Frequency Offset. This value contains Frequency Offset
plus the short term phase correction and can be used to indicate
amount of jitter in the system. The value will be available in the
FREQ_OFFSET bits of this register.
7:0
FREQ_OFFSET
0000 0000, RO
Frequency Offset:
Frequency offset value loaded from the DSP following assertion of the
SAMPLE_FREQ control bit. The Frequency Offset or Frequency
Control value is a twos-complement signed value in units of
approximately 5.1562 ppm. The range is as follows:
0x7F = +655 ppm
0x00 = 0 ppm
0x80 = -660 ppm
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
103
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.4.3 TDR Control Register (TDR_CTRL), Page 2
This register contains control for the Time Domain Reflectometry (TDR) cable diagnostics. The TDR cable
diagnostics sends pulses down the cable and captures reflection data to be used to estimate cable length
and detect certain cabling faults.
Table 10-30. TDR Control Register (TDR_CTRL), address 0x16
Bit
Bit Name
Default
15
TDR_ENABLE
0, RW
Description
TDR Enable:
Enable TDR mode. This forces the powerup state to the correct operating
condition for sending and receiving TDR pulses.
14
TDR_100Mb
0, RW
TDR 100Mb:
Sets the TDR controller to use the 100 Mb Transmitter. This allows for
sending pulse widths in multiples of 8ns. Pulses in 100 Mb mode will
alternate between positive pulses and negative pulses.
Default operation uses the 10 Mb Link Pulse generator. Pulses may
include just the 50 ns pre-emphasis portion of the pulse or the 100 ns full
link pulse (as controlled by setting TDR Width).
13
TX_CHANNEL
0, RW
Transmit Channel Select:
Select transmit channel for sending pulses. The pulse can be sent on the
Transmit or Receive pair.
0 : Transmit channel
1 : Receive channel
12
RX_CHANNEL
0, RW
Receive Channel Select:
Select receive channel for detecting pulses. The pulse can be monitored
on the Transmit or Receive pair.
0 : Transmit channel
1 : Receive channel
11
SEND_TDR
0, RW/SC
Send TDR Pulse:
Setting this bit will send a TDR pulse and enable the monitor circuit to
capture the response. This bit will automatically clear when the capture is
complete.
10:8
TDR_WIDTH
000, RW
TDR Pulse Width:
Pulse width in clocks for the transmitted pulse. In 100 Mb mode, pulses
are in 8 ns increments. In 10 Mb mode, pulses are in 50 ns increments,
but only 50 ns or 100 ns pulses can be sent. Sending a pulse of 0 width
will not transmit a pulse, but allows for baseline testing.
7
TDR_MIN_MODE
0, RW
Min/Max Mode control:
This bit controls direction of the pulse to be detected. Default looks for a
positive peak. Threshold and peak values will be interpreted appropriately
based on this bit.
0 : Max Mode, detect positive peak
1 : Min Mode, detect negative peak
6
RESERVED
0, RW
5:0
RX_THRESHOLD
10 0000, RW
RESERVED: Must be zero.
RX Threshold:
This value provides a threshold for measurement to the start of a peak. If
Min Mode is set to 0, data must be greater than this value to trigger a
capture. If Min Mode is 1, data must be less than this value to trigger a
capture. Data ranges from 0x00 to 0x3F, with 0x20 as the midpoint.
Positive data is greater than 0x20, negative data is less than 0x20.
104
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.4.4 TDR Window Register (TDR_WIN), Page 2
This register contains sample window control for the Time Domain Reflectometry (TDR) cable diagnostics.
The two values contained in this register specify the beginning and end times for the window to monitor
the response to the transmitted pulse. Time values are in 8 ns increments. This provides a method to
search for multiple responses and also to screen out the initial outgoing pulse.
Table 10-31. TDR Window Register (TDR_WIN), address 0x17
Bit
Bit Name
Default
15:8
TDR_START
0000 0000, RW
Description
TDR Start Window:
Specifies start time for monitoring TDR response.
7:0
TDR_STOP
0000 0000, RW
TDR Stop Window:
Specifies stop time for monitoring TDR response. The Stop Window
should be set to a value greater than or equal to the Start Window.
10.4.5 TDR Peak Register (TDR_PEAK), Page 2
This register contains the results of the TDR Peak Detection. Results are valid if the TDR_CTRL[11] is
clear following sending the TDR pulse.
Table 10-32. TDR Peak Register (TDR_PEAK), address 0x18
Bit
Bit Name
Default
15:14
RESERVED
00, RO
13:8
TDR_PEAK
00 0000, RO
Description
RESERVED: Writes ignored, read as 0.
TDR Peak Value:
This register contains the peak value measured during the TDR sample
window. If Min Mode control (TDR_CTRL[7]) is 0, this contains the
maximum detected value. If Min Mode control is 1, this contains the
minimum detected value.
7:0
TDR_PEAK_TIME
0000 0000, RO
TDR Peak Time:
Specifies the time for the first occurrence of the peak value.
10.4.6 TDR Threshold Register (TDR_THR), Page 2
This register contains the results of the TDR Threshold Detection. Results are valid if the TDR_CTRL[11]
is clear following sending the TDR pulse.
Table 10-33. TDR Threshold Register (TDR_THR), address 0x19
Bit
Bit Name
Default
15:9
RESERVED
0000 000, RO
Description
8
TDR_THR_MET
0, RO
RESERVED: Writes ignored, read as 0.
TDR Threshold Met:
This bit indicates the TDR threshold was met during the sample window. A
value of 0 indicates the threshold was not met.
7:0
TDR_THR_TIME
0000 0000, RO
TDR Threshold Time:
Specifies the time for the first data that met the TDR threshold. This field is
only valid if the threshold was met.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
105
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.4.7 Variance Control Register (VAR_CTRL), Page 2
The Variance Control and Data Registers provide control and status for the Cable Signal Quality
Estimation function. The Cable Signal Quality Estimation allows a simple method of determining an
approximate Signal-to-Noise Ratio for the 100 Mb receiver. This register contains the programmable
controls and status bits for the variance computation, which can be used to make a simple Signal-to-Noise
Ratio estimation.
Table 10-34. Variance Control Register (VAR_CTRL), address 0x1A
Bit
Bit Name
Default
15
VAR_RDY
0, RO
Description
Variance Data Ready Status:
Indicates new data is available in the Variance data register. This bit will be
automatically cleared after two consecutive reads of VAR_DATA.
14:4
RESERVED
000 0000 0000, RO
3
VAR_FREEZE
0, RW
RESERVED: Writes ignored, read as 0.
Freeze Variance Registers:
Freeze VAR_DATA register.
This bit is ensures that VAR_DATA register is frozen for software reads. This bit is
automatically cleared after two consecutive reads of VAR_DATA.
2:1
VAR_TIMER
00, RW
Variance Computation Timer (in ms):
Selects the Variance computation timer period. After a new value is written,
computation is automatically restarted. New variance register values are loaded
after the timer elapses.
Var_Timer = 0 => 2 ms timer (default)
Var_Timer = 1 => 4 ms timer
Var_Timer = 2 => 6 ms timer
Var_Timer = 3 => 8 ms timer
Time units are actually 217 cycles of an 8 ns clock, or 1.048576 ms.
0
VAR_ENABLE
0, RW
Variance Enable:
Enable Variance computation. Off by default.
10.4.8 Variance Data Register (VAR_DATA), Page 2
This register contains the 32-bit Variance Sum. The contents of the data are valid only when VAR_RDY is
asserted in the VAR_CTRL register. Upon detection of VAR_RDY asserted, software should set the
VAR_FREEZE bit in the VAR_CTRL register to prevent loading of a new value into the VAR_DATA
register. Since the Variance Data value is 32-bits, two reads of this register are required to get the full
value.
Table 10-35. Variance Data Register (VAR_DATA), address 0x1B
Bit
Bit Name
Default
15:0
VAR_DATA
0000 0000 0000
0000, RO
106
Description
Variance Data:
Two reads are required to return the full 32-bit Variance Sum value. Following
setting the VAR_FREEZE control, the first read of this register will return the low 16
bits of the Variance data. A second read will return the high 16 bits of Variance data.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.4.9 Link Quality Monitor Register (LQMR), Page 2
This register contains the controls for the Link Quality Monitor function. The Link Quality Monitor provides
a mechanism for programming a set of thresholds for DSP parameters. If the thresholds are violated, an
interrupt will be asserted if enabled in the MISR. Monitor control and status are available in this register,
while the LQDR register controls read/write access to threshold values and current parameter values.
Reading the LQMR register clears warning bits and re-arms the interrupt generation. In addition, this
register provides a mechanims for allowing automatic reset of the 100 Mb link based on the Link Quality
Monitor status.
Table 10-36. Link Quality Monitor Register (LQMR), address 0x1D
Bit
Bit Name
Default
15
LQM_ENABLE
0, RW
Description
Link Quality Monitor Enable:
Enables the Link Quality Monitor. The enable is qualified by having a valid 100 Mb
link. In addition, the individual thresholds can be disabled by setting to the
maximum or minimum values.
14
RESTART_ON_FC
0, RW
Restart on Frequency Control Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a
Frequency Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the
threshold violation will also result in a drop in Link status.
13
RESTART_ON
_FREQ
0, RW
Restart on Frequency Offset Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a
Frequency Offset Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the
threshold violation will also result in a drop in Link status.
12
RESTART_ON
_DBLW
0, RW
Restart on DBLW Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a DBLW
Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the threshold
violation will also result in a drop in Link status.
11
RESTART_ON
_DAGC
0, RW
Restart on DAGC Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a DAGC
Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the threshold
violation will also result in a drop in Link status.
10
RESTART_ON_C1
0, RW
Restart on C1 Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a C1
Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the threshold
violation will also result in a drop in Link status.
9
FC_HI_WARN
0, RO/COR
Frequency Control High Warning:
This bit indicates the Frequency Control High Threshold was exceeded. This
register bit will be cleared on read.
8
FC_LO_WARN
0, RO/COR
Frequency Control Low Warning:
This bit indicates the Frequency Control Low Threshold was exceeded. This
register bit will be cleared on read.
7
FREQ_HI_WARN
0, RO/COR
Frequency Offset High Warning:
This bit indicates the Frequency Offset High Threshold was exceeded. This register
bit will be cleared on read.
6
FREQ_LO_WARN
0, RO/COR
Frequency Offset Low Warning:
This bit indicates the Frequency Offset Low Threshold was exceeded. This register
bit will be cleared on read.
5
DBLW_HI_WARN
0, RO/COR
DBLW High Warning:
This bit indicates the DBLW High Threshold was exceeded. This register bit will be
cleared on read.
4
DBLW_LO_WARN
0, RO/COR
DBLW Low Warning:
This bit indicates the DBLW Low Threshold was exceeded. This register bit will be
cleared on read.
3
DAGC_HI_WARN
0, RO/COR
DAGC High Warning:
This bit indicates the DAGC High Threshold was exceeded. This register bit will be
cleared on read.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
107
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-36. Link Quality Monitor Register (LQMR), address 0x1D (continued)
Bit
Bit Name
Default
2
DAGC_LO_WARN
0, RO/COR
Description
DAGC Low Warning:
This bit indicates the DAGC Low Threshold was exceeded. This register bit will be
cleared on read.
1
C1_HI_WARN
0, RO/COR
C1 High Warning:
This bit indicates the DEQ C1 High Threshold was exceeded. This register bit will
be cleared on read.
0
C1_LO_WARN
0, RO/COR
C1 Low Warning:
This bit indicates the DEQ C1 Low Threshold was exceeded. This register bit will
be cleared on read.
10.4.10 Link Quality Data Register (LQDR), Page 2
This register provides read/write control of thresholds for the 100 Mb Link Quality Monitor function. The
register also provides a mechanism for reading current adapted parameter values. Threshold values may
not be written if the device is powered-down.
Table 10-37. Link Quality Data Register (LQDR), address 0x1E
Bit
Bit Name
Default
15:14
RESERVED
00, RO
RESERVED: Writes ignored, read as 0.
Description
13
SAMPLE_PARAM
0, RW
Sample DSP Parameter:
Setting this bit to a 1 enables reading of current parameter values and initiates
sampling of the parameter value. The parameter to be read is selected by the
LQ_PARAM_SEL bits.
12
WRITE_LQ_THR
0, RW
Write Link Quality Threshold:
Setting this bit will cause a write to the Threshold register selected by
LQ_PARAM_SEL and LQ_THR_SEL. The data written is contained in
LQ_THR_DATA. This bit will always read back as 0.
11:9
LQ_PARAM_SEL
000, RW
Link Quality Parameter Select:
This 3-bit field selects the Link Quality Parameter. This field is used for sampling
current parameter values as well as for reads/writes to Threshold values. The
following encodings are available:
000: DEQ_C1
001: DAGC
010: DBLW
011: Frequency Offset
100: Frequency Control
101: Variance most significant bits 31:16
108
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-37. Link Quality Data Register (LQDR), address 0x1E (continued)
Bit
Bit Name
Default
8
LQ_THR_SEL
0, RW
Description
Link Quality Threshold Select:
This bit selects the Link Quality Threshold to be read or written. A 0 selects the
Low threshold, while a 1 selects the high threshold. When combined with the
LQ_PARAM_SEL field, the following encodings are available {LQ_PARAM_SEL,
LQ_THR_SEL}:
000,0: DEQ_C1 Low
000,1: DEQ_C1 High
001,0: DAGC Low
001,1: DAGC High
010,0: DBLW Low
010,1: DBLW High
011,0: Frequency Offset Low
011,1: Frequency Offset High
100,0: Frequency Control Low
100,1: Frequency Control High
101,0: Variance High bits 7:0 (Variance bits 23:16)
101,1: Variance High bits 15:8 (Variance bits 31:24)
7:0
LQ_THR_DATA
1000 0000, RW
Link Quality Threshold Data:
The operation of this field is dependent on the value of the SAMPLE_PARAM bit.
If SAMPLE_PARAM = 0:
On a write, this value contains the data to be written to the selected Link Quality
Threshold register.
On a read, this value contains the current data in the selected Link Quality
Threshold register.
If SAMPLE_PARAM = 1:
On a read, this value contains the sampled parameter value. This value will
remain unchanged until a new read sequence is started.
10.4.11 Link Quality Monitor Register 2 (LQMR2), Page 2
This register contains additional controls for the Link Quality Monitor function. The Link Quality Monitor
provides a mechanism for programming a set of thresholds for DSP parameters. If the thresholds are
violated, an interrupt will be asserted if enabled in the MISR. Monitor control and status are available in
this register, while the LQDR register controls read/write access to threshold values and current parameter
values. Reading of LQMR2 register clears its warning bits but does NOT re-arm the interrupt generation;
LQMR must be read to re-arm interrupt generation. In addition, this register provides a mechanism for
allowing automatic reset of the 100 Mb link based on the Link Quality Monitor variance status.
Table 10-38. Link Quality Monitor Register 2 (LQMR2), address 0x1F
Bit
Bit Name
Default
15:1
1
RESERVED
0000 0, RO
10
RESTART_ON_VAR
0, RW
9:2
RESERVED
00 0000 00, RO
1
VAR_HI_WARN
0, RO/COR
0
RESERVED
0, RO
Description
Reserved: Writes ignored, Read as 0
Restart on Variance Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a
Frequency Offset Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the
threshold violation will also result in a drop in Link status.
Reserved: Writes ignored, Read as 0
Variance High Warning:
This bit indicates the Variance High Threshold was exceeded. This register bit will
be cleared on read.
Reserved: Writes ignored, Read as 0
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
109
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.5 PTP 1588 BASE REGISTERS - PAGE 4
Page 4 PTP 1588 Base Registers are accessible by setting bits [2:0] = 100 of PAGESEL (13h).
10.5.1 PTP Control Register (PTP_CTL), Page 4
This register provides basic control of the PTP 1588 operation.
Table 10-39. PTP Control Register (PTP_CTL), address 0x14
Bit
Bit Name
Default
15:1
3
RESERVED
000, RO
Reserved: Writes ignored, Read as 0
12:1
0
TRIG_SEL
000, RW
PTP Trigger Select:
This field selects the Trigger for loading control information or for enabling the
Trigger.
9
TRIG_DIS
0, RW/SC
Disable PTP Trigger:
Setting this bit will disable the selected Trigger. This bit does not indicate Disable
status for Triggers. The PTP Trigger Status Register should be used to determine
Trigger Status. This bit is self-clearing and will always read back as 0.
Disabling a Trigger will not disconnect it from a GPIO pin. The Trigger value will still
be driven to the GPIO if the Trigger is assigned to a GPIO.
8
TRIG_EN
0, RW/SC
Enable PTP Trigger:
Setting this bit will enable the selected Trigger. This bit does not indicate Enable
status for Triggers. The PTP Trigger Status Register should be used to determine
Trigger Status. This bit is self-clearing and will always read back as 0.
7
TRIG_READ
0, RW/SC
Read PTP Trigger:
Setting this bit will begin the Trigger Read process. The Trigger is selected based on
the setting of the TRIG_SEL bits in this register. Upon setting this bit, subsequent
reads of the PTP_TDR will return the Trigger Control values. Fields are read in the
same order as written.
6
TRIG_LOAD
0, RW/SC
Load PTP Trigger:
Setting this bit will disable the selected Trigger and begin the Trigger load process.
The Trigger is selected based on the setting of the TRIG_SEL bits in this register.
Upon setting this bit, subsequent writes to the PTP_TDR will set the Trigger Control
fields for the selected Trigger. The Trigger Load is completed once all fields have
been written, or the TRIG_EN bit has been set in this register. This bit is selfclearing and will read back as 0 when the Trigger Load is completed either by
writing all Trigger Control fields, or by setting the Trigger Enable.
5
PTP_RD_CLK
0, RW/SC
Read PTP Clock:
Setting this bit will cause the device to sample the PTP Clock time value. The time
value will be made available for reading through the PTP_TDR register. This bit is
self-clearing and will always read back as 0.
4
PTP_LOAD_CLK
0, RW/SC
Load PTP Clock:
Setting this bit will cause the device to load the PTP Clock time value from data
previously written to the PTP_TDR register. This bit is self-clearing and will always
read back as 0.
3
PTP_STEP_CLK
0, RW/SC
Step PTP Clock:
Setting this bit will cause the device to add a value to the PTP Clock. The value to
be added is the value previously written to the PTP_TDR register. This bit is
selfclearing and will always read back as 0.
2
PTP_ENABLE
0, RW
1
PTP_DISABLE
0, RW/SC
Disable PTP Clock:
Setting this bit will disable the PTP Clock. Writing a 0 to this bit will have no effect.
This bit is self-clearing and will always read back as 0.
0
PTP_RESET
0, RW
Reset PTP Clock:
Setting this bit will reset the PTP Clock and associated logic. In addition, the 1588
registers will be reset, with the exception of the PTP_COC and PTP_CLKSRC
registers. Unlike other bits in this register, this bit is not self-clearing and must be
written to 0 to release the clock and logic from reset.
110
Description
Enable PTP Clock:
Setting this bit will enable the PTP Clock. Reading this bit will return the current
enabled value. Writing a 0 to this bit will have no effect.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.5.2 PTP Time Data Register (PTP_TDR), Page 4
This register provides a mechanism for reading and writing the 1588 Time and Trigger Control values. The
function of this register is determined by controls in the PTP_CTL register.
Table 10-40. PTP Time Data Register (PTP_TDR), address 0x15
Bit
Bit Name
Default
15:0
TIME_DATA
XXXX XXXX XXXX
XXXX, RO
XXXX XXXX XXXX
XXXX, WO
Description
Time Data:
On Reads, successively returns 16-bit values of the Clock time or Trigger Control
information as selected by controls in the PTP Control Register. Additional reads
beyond the avaliable fields will always return 0.
On Writes, successively stores the 16-bit values of Clock time or Trigger Control
Information as selected by controls in the PTP Control Register.
10.5.3 PTP Status Register (PTP_STS), Page 4
This register provides basic status and interrupt control for the PTP 1588 operation.
Table 10-41. PTP Status Register (PTP_STS), address 0x16
Bit
Bit Name
Default
Description
15:1
2
RESERVED
0000, RO
11
TXTS_RDY
0, RO
Transmit Timestamp Ready:
A Transmit Timestamp is available for an outbound PTP Message. This bit will be
cleared upon read of the Transmit Timestamp if no other timestamps are ready.
10
RXTS_RDY
0, RO
Receive Timestamp Ready:
A Receive Timestamp is available for an inbound PTP Message. This bit will be
cleared upon read of the Receive Timestamp if no other timestamps are ready.
9
TRIG_DONE
0, RO/COR
PTP Trigger Done:
A PTP Trigger has occured. This bit will be cleared upon read. This bit will only be
set if Trigger Notification is turned on for the Trigger through the Trigger
Configuration Registers.
8
EVENT_RDY
0, RO
PTP Event Timestamp Ready:
A PTP Event Timestamp is available. This bit will be cleared upon read of the PTP
Event Status Register if no other event timestamps are ready.
7:4
RESERVED
0000, RO
3
TXTS_IE
0, RW
Transmit Timestamp Interrupt Enable:
Enable Interrupt on Transmit Timestamp Ready.
2
RXTS_IE
0, RW
Receive Timestamp Interrupt Enable:
Enable Interrupt on Receive Timestamp Ready.
1
TRIG_IE
0, RW
Trigger Interrupt Enable:
Enable Interrupt on Trigger Completion.
0
EVENT_IE
0, RW
Event Interrupt Enable:
Enable Interrupt on Event Timestamp Ready.
Reserved: Writes ignored, Read as 0
Reserved: Writes ignored, Read as 0
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
111
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.5.4 PTP Trigger Status Register (PTP_TSTS), Page 4
This register provides status of the PTP 1588 Triggers. The bits in this register indicate the current status
of each of the Trigger modules. The error bits will be set if the associated notification enable
(TRIGN_NOTIFY) is set in the PTP Trigger Configuration Registers.
Table 10-42. PTP Trigger Status Register (PTP_TSTS), address 0x17
Bit
Bit Name
Default
Description
15
TRIG7_ERROR
0, RO/SC
Trigger 7 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
14
TRIG7_ACTIVE
0, RO/SC
Trigger 7 Active:
This bit indicates the Trigger is enabled and has not completed.
13
TRIG6_ERROR
0, RO/SC
Trigger 6 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
12
TRIG6_ACTIVE
0, RO/SC
Trigger 6 Active:
This bit indicates the Trigger is enabled and has not completed.
11
TRIG5_ERROR
0, RO/SC
Trigger 5 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
10
TRIG5_ACTIVE
0, RO/SC
Trigger 5 Active:
This bit indicates the Trigger is enabled and has not completed.
9
TRIG4_ERROR
0, RO/SC
Trigger 4 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
8
TRIG4_ACTIVE
0, RO/SC
Trigger 4 Active:
This bit indicates the Trigger is enabled and has not completed.
7
TRIG3_ERROR
0, RO/SC
Trigger 3 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
6
TRIG3_ACTIVE
0, RO/SC
Trigger 3 Active:
This bit indicates the Trigger is enabled and has not completed.
5
TRIG2_ERROR
0, RO/SC
Trigger 2 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
4
TRIG2_ACTIVE
0, RO/SC
Trigger 2 Active:
This bit indicates the Trigger is enabled and has not completed.
3
TRIG1_ERROR
0, RO/SC
Trigger 1 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
2
TRIG1_ACTIVE
0, RO/SC
Trigger 1 Active:
This bit indicates the Trigger is enabled and has not completed.
1
TRIG0_ERROR
0, RO/SC
Trigger 0 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior to
the current time. This bit will be cleared when the Trigger is disabled and/ or rearmed.
0
TRIG0_ACTIVE
0, RO/SC
Trigger 0 Active:
This bit indicates the Trigger is enabled and has not completed.
112
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.5.5 PTP Rate Low Register (PTP_RATEL), Page 4
This register contains the low 16-bits of the PTP Rate control. The PTP Rate Control indicates a positive
or negative adjustment to the reference clock period in units of 2-32 ns. On each reference clock cycle, the
PTP Clock will be adjusted by adding REF_CLK_PERIOD +/- PTP_RATE. The PTP Rate should be
written as PTP_RATEH, followed by PTP_RATEL. The rate will take effect on the write to the
PTP_RATEL register.
Table 10-43. PTP Rate Low Register (PTP_RATEL), address 0x18
Bit
Bit Name
Default
15:0
PTP_RATE_LO
0000 0000 0000
0000, RW
Description
PTP Rate Low 16-bits:
Writing to this register will set the low 16-bits of the Rate Control value. The Rate
Control value is in units of 2-32 ns. Upon writing to this register, the full Rate Control
value will be loaded to the device.
10.5.6 PTP Rate High Register (PTP_RATEH), Page 4
This register contains the upper bits of the PTP Rate control. In addition, it contains a direction control to
indicate whether the device is operating faster or slower than the reference clock frequency. When setting
the PTP Rate, this register should be written first, followed by a write to the PTP_RATEL register. The rate
will take effect on the write to the PTP_RATEL register.
Table 10-44. PTP Rate High Register (PTP_RATEH), address 0x19
Bit
Bit Name
Default
15
PTP_RATE_DIR
0, RW
PTP Rate Direction:
The setting of this bit controls whether the device will operate at a higher or lower
frequency than the reference clock.
0 : Higher Frequency. The PTP_RATE value will be added to the clock on every
cycle.
1 : Lower Frequency. The PTP_RATE value will be subtracted from the clock on
every cycle.
Description
14
PTP_TMP_RATE
0, RW
PTP Temporary Rate:
Setting this bit will cause the rate to be applied to the clock for the duration set in the
PTP Temporary Rate Duration Register (PTP_TRD).
1 : Temporary Rate
0 : Normal Rate
13:10
RESERVED
00 00, RO
9:0
PTP_RATE_HI
00 0000 0000, RW
Reserved: Writes ignored, Read as 0
PTP Rate High 10-bits:
Writing to this register will set the high 10-bits of the Rate Control value. The Rate
Control value is in units of 2-32 ns.
10.5.7 PTP Read Checksum (PTP_RDCKSUM), Page 4
This register keeps a running one’s complement checksum of 16-bit read data values for valid Page 4
read accesses. Clear the checksum on a read to this register; read data from this register is not
accumulated in the read checksum since the register is cleared on read. However, read data from the
write checksum register is accumulated to allow cross checking. Checksums are not accumulated for PHY
Control Frame register accesses, but are cleared on management or PHY Control Frame reads.
Table 10-45. PTP Read Checksum (PTP_RDCKSUM), address 0x1A
Bit
Bit Name
Default
15:0
RD_CKSUM
XXXX XXXX XXXX
XXXX, RO/ COR
Description
PTP Page 4 Read Checksum.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
113
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.5.8 PTP Write Checksum (PTP_WRCKSUM), Page 4
This register keeps a running one’s complement checksum of 16-bit write data values for Page 4 write
accesses. Clear the checksum on a read. Write data to this register or the read checksum register ARE
accumulated in the write checksum to allow cross checking. Read data from this register is accumulated in
the read checksum to allow cross checking. Checksums are not accumulated for PHY Control Frame
register accesses, but are cleared on management or PHY Control Frame reads.
Table 10-46. PTP Write Checksum (PTP_WRCKSUM), address 0x1B
Bit
Bit Name
Default
15:0
WR_CKSUM
XXXX XXXX XXXX
XXXX, RO/ COR
Description
PTP Page 4 Write Checksum.
10.5.9 PTP Transmit Timestamp Register (PTP_TXTS), Page 4
This register provides a mechanism for reading the Transmit Timestamp. The fields are read in the
following order:
• Timestamp_ns [15:0]
• Overflow_cnt[1:0], Timestamp_ns[29:16]
• Timestamp_sec[15:0]
• Timestamp_sec[31:16]
The Overflow_cnt value indicates if timestamps were dropped due to an overflow of the Transmit
Timestamp queue. The overflow counter will stick at a value of three if additional timestamps were missed.
Table 10-47. PTP Transmit Timestamp Register (PTP_TXTS), address 0x1C
Bit
Bit Name
Default
15:0
PTP_TX_TS
0000 0000 0000
0000, RO
Description
PTP Transmit Timestamp:
Reading this register will return the Transmit Timestamp in four 16-bit reads.
10.5.10 PTP Receive Timestamp Register (PTP_RXTS), Page 4
This register provides a mechanism for reading the Receive Timestamp and identification information. The
fields are read in the following order:
• Timestamp_ns [15:0]
• Overflow_cnt[1:0], Timestamp_ns[29:16]
• Timestamp_sec[15:0]
• Timestamp_sec[31:16]
• sequenceId[15:0]
• messageType[3:0], source_hash[11:0]
The Overflow_cnt value indicates if timestamps were dropped due to an overflow of the Transmit
Timestamp queue. The overflow counter will stick at a value of three if additional timestamps were missed.
Table 10-48. PTP Receive Timestamp Register (PTP_RXTS), address 0x1D
Bit
Bit Name
Default
15:0
PTP_RX_TS
0000 0000 0000
0000, RO
114
Description
PTP Receive Timestamp:
Reading this register will return the Receive Timestamp in four 16-bit reads.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.5.11 PTP Event Status Register (PTP_ESTS), Page 4
This register provides Status for the Event Timestamp unit. Reading this register provides status for the
next Event Timestamp contained in the Event Data Register. If this register is 0, no Event Timestamp is
available in the Event Data Register. Reading this register will automatically move to the next Event in the
queue.
Table 10-49. PTP Event Status Register (PTP_ESTS), address 0x1E
Bit
Bit Name
Default
15:11
RESERVED
0000 0, RO
Reserved: Writes ignored, Read as 0
Description
10:8
EVNTS_MISSED
000, RO/SC
Event Missed:
Indicates number of events have been missed prior to this timestamp for the
EVNT_NUM indicated. This count value will stick at 7 if more than 7 events are
missed.
7:6
EVNT_TS_LEN
00, RO/SC
Event Timestamp Length:
Indicates length of the Timestamp field in 16-bit words minus 1. Although all fields
are available, this indicates how many of the fields contain data different from the
previous Event Timestamp. This allows software to avoid reading more significant
fields if they have not changed since the previous timestamp. This field is valid for
both single and multiple events. The following shows the number of least significant
fields which have new data for each setting of TS_LENGTH:
00 : One 16-bit field is new (Timestamp_ns[15:0])
01 : Two 16-bit fields are new
10 : Three 16-bit fields are new
11 : All four 16-bit fields are new
5
EVNT_RF
0, RO/SC
Event Rise/Fall direction:
Indicates whether the event is a rise or falling event. If the MULT_EVNT bit is set to
1, this bit indicates the Rise/Fall direction for the event indicated by EVNT_NUM.
0 = Falling edge detected
1 = Rising edge detected
4:2
EVNT_NUM
000, RO/SC
Event Number:
Indicates Event Timestamp Unit which detected an event. If the MULT_EVNT bit is
set to 0, this indicates the lowest event number captured. If events have been
missed prior to this timestamp, it indicates the lowest event number captured which
had at least one missed event.
1
MULT_EVNT
0, RO/SC
Multiple Event Detect:
Indicates multiple events were detected at the same time. If multiple events are
detected, an extended event status field is available as the first data read from the
Event Data Register.
0 = Single event detected
1 = Multiple events detected
0
EVENT_DET
0, RO/SC
PTP Event Detected:
Indicates an Event has been detected by one of the Event Timestamp Units.
10.5.12 PTP Event Data Register (PTP_EDATA), Page 4
This register provides a mechanism for reading the Event Timestamp and extended event status. If
present, the extended event status is read prior to reading the Event Timestamp. Presence of the
Extended Event Status field is indicated by the MULT_EVNT bit in the PTP Event Status Register. The
timestamp consists of four 16-bit fields. This register contains a valid timestamp if the PTP_ESTS register
indicates an Event Timestamp is available. Not all fields have to be read for each timestamp. For example,
if the EVNT_TS_LEN indicates the seconds field has not changed from the previous event, software may
skip that read. Reading the PTP_ESTS register will cause the device to move to the next available
timestamp.
The fields are read in the following order:
• Extended Event Status[15:0] (only available if PTP_ESTS indicates detection of multiple events)
• Timestamp_ns [15:0]
• Timestamp_ns[29:16] (upper 2 bits are always 0)
• Timestamp_sec[15:0]
• Timestamp_sec[31:16]
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
115
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
For Extended Event Status, the following definition is used for the PTP Event Data Register:
Table 10-50. PTP Event Data Register (PTP_EDATA), address 0x1F
Bit
Bit Name
Default
15
E7_RISE
0, RO/SC
Rise/Fall edge direction for Event 7:
Indicates direction of Event 7
0 = Fall
1 = Rise
14
E7_DET
0, RO/SC
Event 7 detected:
Indicates Event 7 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
13
E6_RISE
0, RO/SC
Rise/Fall edge direction for Event 6:
Indicates direction of Event 6
0 = Fall
1 = Rise
12
E6_DET
0, RO/SC
Event 6 detected:
Indicates Event 6 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
11
E5_RISE
0, RO/SC
Rise/Fall edge direction for Event 5:
Indicates direction of Event 5
0 = Fall
1 = Rise
10
E5_DET
0, RO/SC
Event 5 detected:
Indicates Event 5 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
9
E4_RISE
0, RO/SC
Rise/Fall edge direction for Event 4:
Indicates direction of Event 4
0 = Fall
1 = Rise
8
E4_DET
0, RO/SC
Event 4 detected:
Indicates Event 4 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
7
E3_RISE
0, RO/SC
Rise/Fall edge direction for Event 3:
Indicates direction of Event 3
0 = Fall
1 = Rise
6
E3_DET
0, RO/SC
Event 3 detected:
Indicates Event 3 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
5
E2_RISE
0, RO/SC
Rise/Fall edge direction for Event 2:
Indicates direction of Event 2
0 = Fall
1 = Rise
4
E2_DET
0, RO/SC
Event 2 detected:
Indicates Event 2 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
3
E1_RISE
0, RO/SC
Rise/Fall edge direction for Event 1:
Indicates direction of Event 1
0 = Fall
1 = Rise
2
E1_DET
0, RO/SC
Event 1 detected:
Indicates Event 1 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
1
E0_RISE
0, RO/SC
Rise/Fall edge direction for Event 0:
Indicates direction of Event 0
0 = Fall
1 = Rise
0
E0_DET
0, RO/SC
Event 0 detected:
Indicates Event 0 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
116
Description
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
For timestamp fields, the following definition is used for the PTP Event Data Register:
Table 10-51. PTP Event Data Register (PTP_EDATA), address 0x1F
Bit
Bit Name
Default
15:0
PTP_EVNT_TS
XXXX XXXX XXXX
XXXX, RO
Description
PTP Event Timestamp:
Reading this register will return 16 bits of the Event Timestamp.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
117
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.6 PTP 1588 CONFIGURATION REGISTERS - PAGE 5
Page 5 PTP 1588 Configuration Registers are accessible by setting bits [2:0] = 101 of PAGESEL (13h).
10.6.1 PTP Trigger Configuration Register (PTP_TRIG), Page 5
This register provides basic configuration for IEEE 1588 Triggers. To write configuration to a Trigger, set
the TRIG_WR bit along with the TRIG_SEL and other control information. To read configuration from a
Trigger, set the TRIG_SEL encoding to the Trigger desired, and set the TRIG_WR bit to 0. The
subsequent read of the PTP_TRIG register will return the configuration information.
Table 10-52. PTP Trigger Configuration Register (PTP_TRIG), address 0x14
Bit
Bit Name
Default
15
TRIG_PULSE
0, RW
Trigger Pulse:
Setting this bit will cause the Trigger to generate a Pulse rather than a single rising
or falling edge.
14
TRIG_PER
0, RW
Trigger Periodic:
Setting this bit will cause the Trigger to generate a periodic signal. If this bit is 0, the
Trigger will generate a single Pulse or Edge depending on the Trigger Control
settings.
13
TRIG_IF_LATE
0, RW
Trigger-if-late Control:
Setting this bit will allow an immediate Trigger in the event the Trigger is
programmed to a time value which is less than the current time. This provides a
mechanism for generating an immediate trigger or to immediately begin generating a
periodic signal. For a periodic signal, no notification be generated if this bit is set
and a Late Trigger occurs.
12
TRIG_NOTIFY
0, RW
Trigger Notification Enable:
Setting this bit will enable Trigger status to be reported on completion of a Trigger or
on an error detection due to late trigger. If Trigger interrupts are enabled, the
notification will also result in an interrupt being generated.
11:8
TRIG_GPIO
0000, RW
Trigger GPIO Connection:
Setting this field to a non-zero value will connect the Trigger to the associated GPIO
pin. Valid settings for this field are 1 thru 12.
7
TRIG_TOGGLE
0, RW
6:4
RESERVED
000, RO
Reserved: Writes ignored, Read as 0
3:1
TRIG_CSEL
000, RW
Trigger Configuration Select:
This field selects the Trigger for configuration read or write.
0
TRIG_WR
0, RW/SC
Trigger Configuration Write:
Setting this bit will generate a Configuration Write to the selected Trigger. This bit
will always read back as 0.
118
Description
Trigger Toggle Mode Enable:
Setting this bit will put the trigger into toggle mode. In toggle mode, the initial value
will be ignored and the trigger output will be toggled at the trigger time.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.6.2 PTP Event Configuration Register (PTP_EVNT), Page 5
This register provides basic configuration for IEEE 1588 Events. To write configuration to an Event
Timestamp Unit, set the EVNT_WR bit along with the EVNT_SEL and other control information. To read
configuration from an Event Timestamp Unit, set the EVNT_SEL encoding to the Event desired, and set
the EVNT_WR bit to 0. The subsequent read of the PTP_EVNT register will return the configuration
information.
Table 10-53. PTP Event Configuration Register (PTP_EVNT), address 0x15
Bit
Bit Name
Default
15
RESERVED
0, RO
Reserved: Writes ignored, Read as 0
Description
14
EVNT_RISE
0, RW
Event Rise Detect Enable:
Enable Detection of Rising edge on Event input.
13
EVNT_FALL
0, RW
Event Fall Detect Enable:
Enable Detection of Falling edge on Event input.
12
EVNT_SINGLE
0, RW
Single Event Capture: Setting this bit to a 1 will enable single event capture
operation. The EVNT_RISE and EVNT_FALL enables will be cleared upon a valid
event timestamp capture.
11:8
EVNT_GPIO
0000, RW
Event GPIO Connection:
Setting this field to a non-zero value will connect the Event to the associated GPIO
pin. Valid settings for this field are 1 thru 12.
7:4
RESERVED
0000, RO
Reserved: Writes ignored, Read as 0
3:1
EVNT_SEL
000, RW
Event Select:
This field selects the Event Timestamp Unit for configuration read or write.
0
EVNT_WR
0, RW
Event Configuration Write:
Setting this bit will generate a Configuration Write to the selected Event Timestamp
Unit.
10.6.3 PTP Transmit Configuration Register 0 (PTP_TXCFG0), Page 5
This register provides configuration for IEEE 1588 Transmit Timestamp operation.
Table 10-54. PTP Transmit Configuration Register 0 (PTP_TXCFG0), address 0x16
Bit
Bit Name
Default
15
SYNC_1STEP
0, RW
Sync Message One-Step Enable:
Enable automatic insertion of timestamp into transmit Sync Messages. Device will
automatically parse message and insert the timestamp in the correct location. UPD
checksum and CRC fields will be regenerated.
Description
14
RESERVED
0, RO
Reserved: Writes ignored, Read as 0
13
DR_INSERT
0, RW
Insert Delay_Req Timestamp in Delay_Resp:
If this bit is set to a 1, the device insert the timestamp for transmitted Delay_Req
messages into inbound Delay_Resp messages. The most recent timestamp will be
used for any inbound Delay_Resp message. The receive timestamp insertion logic
must be enabled through the PTP Receive Configuration Registers.
12
NTP_TS_EN
0, RW
Enable Timestamping of NTP Packets:
If this bit is set to 0, the device will check the UDP protocol field for a PTP Event
message (value 319). If this bit is set to 1, the device will check the UDP protocol
field for an NTP message (value 123). This setting applies to the transmit and
receive packet parsing engines.
11
IGNORE_2STEP
0, RW
Ignore Two_Step flag for One-Step operation:
If this bit is set to a 0, the device will not insert a timestamp if the Two_Step bit is set
in the flags field of the PTP header. If this bit is set to 1, the device will insert a
timestamp independent of the setting of the Two_Step flag.
10
CRC_1STEP
0, RW
Disable checking of CRC for One-Step operation:
If this bit is set to a 0, the device will force a CRC error for One-Step operation if the
incoming frame has a CRC error. If this bit is set to a 1, the device will send the
One- Step frame with a valid CRC, even if the incoming CRC is invalid.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
119
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Table 10-54. PTP Transmit Configuration Register 0 (PTP_TXCFG0), address 0x16 (continued)
Bit
Bit Name
Default
9
CHK_1STEP
0, RW
Enable UDP Checksum correction for One-Step Operation:
Enables correction of the UDP checksum for messages which include insertion of
the timestamp. The checksum is corrected by modifying the last two bytes of the
UDP data. The last two bytes must be transmitted by the MAC as 0’s. This control
must be set for proper IPv6/UDP One-Step operation. This control will have no
effect for Layer2 Ethernet messages.
Description
8
IP1588_EN
0, RW
Enable IEEE 1588 defined IP address filter:
Enable filtering of UDP/IP Event messages using the IANA assigned IP Destination
addresses. If this bit is set to 1, packets with IP Destination addresses which do not
match the IANA assigned addresses will not be timestamped. This field affects
operation for both IPv4 and IPv6. If this field is set to 0, IP destination addresses will
be ignored.
7
TX_L2_EN
0, RW
Layer2 Timestamp Enable:
Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages.
6
TX_IPV6_EN
0, RW
IPv6 Timestamp Enable:
Enables detection of UDP/IPv6 encapsulated PTP event messages.
5
TX_IPV4_EN
0, RW
IPv4 Timestamp Enable:
Enables detection of UDP/IPv4 encapsulated PTP event messages.
4:1
TX_PTP_VER
0 000, RW
0
TX_TS_EN
0, RW
PTP Version:
Enable Timestamp capture for a specific version of the IEEE 1588 specification. This
field may be programmed to any value between 1 and 15 and allows support for
future versions of the IEEE 1588 specification. A value of 0 will disable version
checking (not recommended).
Transmit Timestamp Enable:
Enable Timestamp capture for Transmit.
10.6.4 PTP Transmit Configuration Register 1 (PTP_TXCFG1), Page 5
This register provides data and mask fields to filter the first byte in a PTP Message. This function will be
disabled if all the mask bits are set to 0.
Table 10-55. PTP Transmit Configuration Register 1 (PTP_TXCFG1), address 0x17
Bit
Bit Name
Default
15:8
BYTE0_MASK
0000 0000, RW
Byte0 Data:
Bit mask to be used for matching Byte0 of the PTP Message. A one in any bit
enables matching for the associated data bit. If no matching is required, all bits of
the mask should be set to 0.
7:0
BYTE0_DATA
0000 0000, RW
Byte0 Mask:
Data to be used for matching Byte0 of the PTP Message.
120
Description
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.6.5 PHY Status Frame Configuration Register 0 (PSF_CFG0), Page 5
This register provides configuration for the PHY Status Frame function.
Table 10-56. PHY Status Frame Configuration Register 0 (PSF_CFG0), address 0x18
Bit
Bit Name
Default
15:1
3
RESERVED
000, RO
Reserved: Writes ignored, Read as 0
Description
12:1
1
MAC_SRC_ADD
0 0, RW
PHY Status Frame Mac Source Address:
Selects source address as follows:
00 : Use Mac Address [08 00 17 0B 6B 0F]
01 : Use Mac Address [08 00 17 00 00 00]
10 : Use Mac Multicast Dest Address
11 : Use Mac Address [00 00 00 00 00 00]
10:8
MIN_PRE
000, RW
PHY Status Frame Minimum Preamble:
Determines the minimum preamble bytes required for sending packets on the MII
interface. It is recommended that this be set to the smallest value the MAC will
tolerate.
7
PSF_ENDIAN
0, RW
PHY Status Frame Endian Control:
For each 16-bit field in a Status Message, the data will normally be presented in
network byte order (Most significant byte first). If this bit is set to a 1, the byte data
fields will be reversed so that the least significant byte is first.
6
PSF_IPV4
0, RW
PHY Status Frame IPv4 Enable:
This bit controls the type of packet used for PHY Status Frames.
0 = Layer2 Ethernet packets
1 = IPv4 packets.
5
PSF_PCF_RD
0, RW
PHY Control Frame Read PHY Status Frame Enable:
Enable PHY Status Frame delivery of PHY Control Frame read data. Data read via
a PHY Control Frame will be returned in a PHY Status Frame.
4
PSF_ERR_EN
0, RW
PSF Error PHY Status Frame Enable:
Enable PHY Status Frame delivery of PHY Status Frame Errors. This bit will not
independently enable PHY Status Frame operation. One of the other enable bits
must be set for PHY Status Frames to be generated.
3
PSF_TXTS_EN
0, RW
Transmit Timestamp PHY Status Frame Enable:
Enable PHY Status Frame delivery of Transmit Timestamps.
2
PSF_RXTS_EN
0, RW
Receive Timestamp PHY Status Frame Enable:
Enable PHY Status Frame delivery of Receive Timestamps.
1
PSF_TRIG_EN
0, RW
Trigger PHY Status Frame Enable:
Enable PHY Status Frame delivery of Trigger Status.
0
PSF_EVNT_EN
0, RW
Event PHY Status Frame Enable:
Enable PHY Status Frame delivery of Event Timestamps.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
121
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.6.6 PTP Receive Configuration Register 0 (PTP_RXCFG0), Page 5,
This register provides configuration for IEEE 1588 Receive Timestamp operation.
Table 10-57. PTP Receive Configuration Register 0 (PTP_RXCFG0), address 0x19
Bit
Bit Name
Default
Description
15
DOMAIN_EN
0, RW
Domain Match Enable:
If set to 1, the Receive Timestamp unit will require the Domain field to match the
value programmed in the PTP_DOMAIN field of the PTP_RXCFG3 register. If set to
0, the Receive Timestamp will ignore the PTP_DOMAIN field.
14
ALT_MAST_DIS
0, RW
Alternate Master Timestamp Disable:
Disables timestamp generation if the Alternate_Master flag is set:
1 = Do not generate timestamp if Alternate_Master = 1
0 = Ignore Alternate_Master flag
13
USER_IP_SEL
0, RW
IP Address data select:
Selects portion of IP address accessible through the PTP_RXCFG2 register:
0 = Most Significant Octets
1 = Least Significant Octets
12
USER_IP_EN
0, RW
Enable User-programmed IP address filter:
Enable detection of UDP/IP Event messages using a programmable IP addresses.
The IP Address is set using the PTP_RXCFG2 register.
11
RX_SLAVE
0, RW
Receive Slave Only:
By default, the Receive Timestamp Unit will provide Timestamps for event
messages meeting other requirements. Setting this bit to a 1 will prevent Delay_Req
messages from being Timestamped by requiring that the Control Field (offset 32 in
the PTP message) be set to a value other than 1.
10:8
IP1588_EN
000, RW
7
RX_L2_EN
0, RW
Layer2 Timestamp Enable:
Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages.
6
RX_IPV6_EN
0, RW
IPv6 Timestamp Enable:
Enables detection of UDP/IPv6 encapsulated PTP event messages.
5
RX_IPV4_EN
0, RW
IPv4 Timestamp Enable:
Enables detection of UDP/IPv4 encapsulated PTP event messages.
4:1
RX_PTP_VER
0 000, RW
0
RX_TS_EN
0, RW
122
Enable IEEE 1588 defined IP address filters:
Enable detection of UDP/IP Event messages using the IANA assigned IP
Destination addresses. This field affects operation for both IPv4 and IPv6. A
Timestamp is captured for the PTP message if the IP destination address matches
the following:
IP1588_EN[0]: Dest IP address = 224.0.1.129
IP1588_EN[1]: Dest IP address = 224.0.1.130-132
IP1588_EN[2]: Dest IP address = 224.0.0.107
PTP Version:
Enable Timestamp capture for a specific version of the IEEE 1588 specification. This
field may be programmed to any value between 1 and 15 and allows support for
future versions of the IEEE 1588 specification. A value of 0 will disable version
checking (not recommended).
Receive Timestamp Enable:
Enable Timestamp capture for Receive.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.6.7 PTP Receive Configuration Register 1 (PTP_RXCFG1), Page 5
This register provides data and mask fields to filter the first byte in a PTP Message. This function will be
disabled if all the mask bits are set to 0.
Table 10-58. PTP Receive Configuration Register 1 (PTP_RXCFG1), address 0x1A
Bit
Bit Name
Default
Description
15:8
BYTE0_MASK
0000 0000, RW
Byte0 Data:
Bit mask to be used for matching Byte0 of the Receive PTP Message. A one in any
bit enables matching for the associated data bit. If no matching is required, all bits of
the mask should be set to 0.
7:0
BYTE0_DATA
0000 0000, RW
Byte0 Mask:
Data to be used for matching Byte0 of the Receive PTP Message.
10.6.8 PTP Receive Configuration Register 2 (PTP_RXCFG2), Page 5
This register provides for programming an IP address to be used for filtering packets to detect PTP Event
Messages. Since the IPv4 address is 32-bits, to write an IP address, software must write two 16-bit
values. The USER_IP_SEL bit in the PTP_RXCFG0 register selects which octects of the IP address are
accessible through this register. For example, to write an IP address of 224.0.1.129, software should do
the following:
1. Set USER_IP_SEL bit in PTP_RXCFG0 register to 0
2. Write 0xE000 (224.00) to PTP_RXCFG2
3. Set USER_IP_SEL bit in the PTP_RXCFG0 register to 1
4. Write 0x0181 (01.129) to PTP_RXCFG2
Reading this registerwill return the IP address field selected by USER_IP_SEL.
Table 10-59. PTP Receive Configuration Register 2 (PTP_RXCFG2), address 0x1B
Bit
Bit Name
Default
Description
15:0
IP_ADDR_DATA
0000 0000 0000
0000, RW
Receive IP Address Data:
16-bits of the IP Address field to be read or written. The USER_IP_SEL bit in the
PTP_RXCFG0 Register selects the portion of the IP address is to be read or written.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
123
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.6.9 PTP Receive Configuration Register 3 (PTP_RXCFG3), Page 5
This register provides extended configuration for IEEE 1588 Receive Timestamp operation.
Table 10-60. PTP Receive Configuration Register 3 (PTP_RXCFG3), address 0x1C
Bit
Bit Name
Default
15:1
2
TS_MIN_IFG
1100, RW
Minimum Inter-frame Gap:
When a Timestamp is appended to a PTP Message, the length of the packet may
get extended. This could reduce the Inter-frame Gap (IFG) between packets by as
much as 8 byte times (640 ns at 100 Mb). This field sets a minimum on the IFG
between packets in number of byte times. If the IFG is set larger than the actual
IFG, preamble bytes of the subsequent packet will get dropped. This value should
be set to the lowest possible value that the attached MAC can support.
Description
11
ACC_UDP
0, RW
Record Timestamp if UDP Checksum Error:
By default, Timestamps will be discarded for packets with UDP Checksum errors. If
this bit is set, then the Timestamp will be made available in the normal manner.
10
ACC_CRC
0, RW
Record Timestamp if CRC Error:
By default, Timestamps will be discarded for packets with CRC errors. If this bit is
set, then the Timestamp will be made available in the normal manner.
9
TS_APPEND
0, RW
Append Timestamp for L2:
For Layer 2 encapsulated PTP messages, if this bit is set, always append the
Timestamp to end of the PTP message rather than inserted in unused message
fields. This bit will be ignored if TS_INSERT is 0.
8
TS_INSERT
0, RW
Enable Timestamp Insertion:
Enables Timestamp insertion into a packet containing a PTP Event Message. If this
bit is set, the Timestamp will not be available through the PTP Receive Timestamp
Register.
7:0
PTP_DOMAIN
0000 0000, RW
PTP Domain:
Value of the PTP Message domainNumber field. If PTP_RXCFG0:DOMAIN_EN is
set to 1, the Receive Timestamp unit will only capture a Timestamp if the
domainNumber in the receive PTP message matches the value in this field. If the
DOMAIN_EN bit is set to 0, the domainNumber field will be ignored.
10.6.10 PTP Receive Configuration Register 4 (PTP_RXCFG4), Page 5
This register provides extended configuration for IEEE 1588 Receive Timestamp operation.
Table 10-61. PTP Receive Configuration Register 4 (PTP_RXCFG4), address 0x1D
Bit
Bit Name
Default
Description
15
IPV4_UDP_MOD
0, RW
Enable IPV4 UDP Modification:
When timestamp insertion is enabled, this bit controls how UDP checksums are
handled for IPV4 PTP event messages.
If set to a 0, the device will clear the UDP checksum. If a UDP checksum error is
detected the device will force a CRC error.
If set to a 1, the device will not clear the UDP checksum. Instead it will generate a 2byte value to correct the UDP checksum and append this immediately following the
PTP message. If an incoming UDP checksum error is detected, the device will
cause a UDP checksum error in the modified field. This function should only be used
if the incoming packets contain two extra bytes of UDP data following the PTP
message. This should not be enabled for systems using version 1 of the IEEE 1588
specification.
14
TS_SEC_EN
0, RW
Enable Timestamp Seconds:
Setting this bit to a 1 enables inserting a seconds field when Timestamp Insertion is
enabled. If set to 0, only the nanoseconds portion of the Timestamp will be inserted
in the packet. This bit will be ignored if TS_INSERT is 0.
13:1
2
TS_SEC_LEN
00, RW
Inserted Timestamp Seconds Length:
This field indicates the length of the Seconds field to be inserted in the PTP
message. This field will be ignored if TS_INSERT is 0 or if TS_SEC_EN is 0. The
mapping is as follows:
00 : Least Significant Byte only of Seconds field
01 : Two Least Significant Bytes of Seconds field
10 : Three Least Significant Bytes of Seconds field
11 : All four Bytes of Seconds field
124
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
Table 10-61. PTP Receive Configuration Register 4 (PTP_RXCFG4), address 0x1D (continued)
Bit
Bit Name
Default
11:6
RXTS_NS_OFF
0000 00, RW
Receive Timestamp Nanoseconds offset:
This field provides an offset to the Nanoseconds field when inserting a Timestamp
into a received PTP message. If TS_APPEND is set to 1, the offset indicates an
offset from the end of the PTP message. If TS_APPEND is set to 0, the offset
indicates the byte offset from the beginning of the PTP message. This field will be
ignored if TS_INSERT is 0.
Description
5:0
RXTS_SEC_OFF
00 0000, RW
Receive Timestamp Seconds offset:
This field provides an offset to the Seconds field when inserting a Timestamp into a
received PTP message. If TS_APPEND is set to 1, the offset indicates an offset
from the end of the inserted Nanoseconds field. If TS_APPEND is set to 0, the offset
indicates the byte offset from the beginning of the PTP message. This field will be
ignored if TS_INSERT is 0.
10.6.11 PTP Temporary Rate Duration Low Register (PTP_TRDL), Page 5
This register contains the low 16 bits of the duration in clock cycles to use the Temporary Rate as
programmed in the PTP_RATEH and PTP_RATEL registers. Since the Temporary Rate takes affect upon
writing the PTP_RATEL register, this register should be programmed before setting the Temporary Rate.
This register does not need to be reprogrammed for each use of the Temporary Rate registers.
Table 10-62. PTP Temporary Rate Duration Low Register (PTP_TRDL), address 0x1E
Bit
Bit Name
Default
15:0
PTP_TR_DURL
0000 0000 0000
0000, RW
Description
PTP Temporary Rate Duration Low 16 bits:
This register sets the duration for the Temporary Rate in number of clock cycles.
The actual Time duration is dependent on the value of the Temporary Rate.
10.6.12 PTP Temporary Rate Duration High Register (PTP_TRDH), Page 5
This register contains the high 10 bits of the duration in clock cycles to use the Temporary Rate as
programmed in the PTP_RATEH and PTP_RATEL registers. Since the Temporary Rate takes affect upon
writing the PTP_RATEL register, this register should be programmed before setting the Temporary Rate.
This register does not need to be reprogrammed for each use of the Temporary Rate registers.
Table 10-63. PTP Temporary Rate Duration High Register (PTP_TRDH), address 0x1F
Bit
Bit Name
Default
15:10
RESERVED
0000 00, RO
9:0
PTP_TR_DURH
00 0000 0000, RW
Description
Reserved: Writes ignored, Read as 0
PTP Temporary Rate Duration High 10 bits:
This register sets the duration for the Temporary Rate in number of clock cycles.
The actual Time duration is dependent on the value of the Temporary Rate.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
125
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.7 PTP 1588 CONFIGURATION REGISTERS - PAGE 6
Page 6 PTP 1588 Configuration Registers are accessible by setting bits [2:0] = 110 of PAGESEL (13h).
10.7.1 PTP Clock Output Control Register (PTP_COC), Page 6
This register provides configuration for the PTP clock-synchronized output divide-by-N clock.
Table 10-64. PTP Clock Output Control Register (PTP_COC), address 0x14
Bit
Bit Name
Default
15
PTP_CLKOUT EN
1, RW
PTP Clock Output Enable:
1 = Enable PTP divide-by-N clock output.
0 = Disable PTP divide-by-N clock output.
14
PTP_CLKOUT SEL
0, RW
PTP Clock Output Source Select:
1 = Select the Phase Generation Module (PGM) as the root clock for generating the
divide-by-N output.
0 = Select the Frequency-Controlled Oscillator (FCO) as the root clock for
generating the divide-by-N output.
For additional information related to the PTP clock output selection, refer to TI Lit
Number SNLA099.
13
PTP_CLKOUT
SPEEDSEL
0, RW
PTP Clock Output I/O Speed Select:
1 = Enable faster rise/fall time for the divide-by-N clock output pin.
0 = Enable normal rise/fall time for the divide-by-N clock output pin.
12:8
RESERVED
0 0000, RO
7:0
PTP_CLKDIV
0000 1010, RW
Description
Reserved: Writes ignored, Read as 0
PTP Clock Divide-by Value:
This field sets the divide-by value for the output clock. The output clock is divided
from an internal 250 MHz clock. Valid values range from 2 to 255 (0x02 to 0xFF),
giving a nominal output frequency range of 125 MHz down to 980.4 kHz. Divide-by
values of 0 and 1 are not valid and will stop the output clock.
10.7.2 PHY Status Frame Configuration Register 1 (PSF_CFG1), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this
register is used as the first 16-bits of the PTP Header data for the PHY Status Frame.
Table 10-65. PHY Status Frame Configuration Register 1 (PSF_CFG1), address 0x15
Bit
Bit Name
Default
15:12
PTPRESERVED
0000, RW
PTP v2 reserved field:
This field contains the reserved 4-bit field (at offset 1) to be sent in status packets
from the PHY to the local MAC using the MII receive data interface.
11:8
VERSIONPTP
0000, RW
PTP v2 versionPTP field:
This field contains the versionPTP field to be sent in status packets from the PHY to
the local MAC using the MII receive data interface.
7:4
TRANSPORTSPECIFIC
0000, RW
PTP v2 Header transportSpecific field:
This field contains the MESSAGETYPE field to be sent in status packets from the
PHY to the local MAC using the MII receive data interface.
3:0
MESSAGETYPE
0000, RW
PTP v2 messageType field:
This field contains the MESSAGETYPE field to be sent in status packets from the
PHY to the local MAC using the MII receive data interface.
126
Description
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.7.3 PHY Status Frame Configuration Register 2 (PSF_CFG2), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this
register is used as the first 16-bits of the IP Source address for an IPv4 PHY Status Frame.
Table 10-66. PHY Status Frame Configuration Register 2 (PSF_CFG2), address 0x16
Bit
Bit Name
Default
15:8
IP_SA_BYTE1
0000 0000, RW
Second byte of IP source address:
This field contains the second byte of the IP source address.
Description
7:0
IP_SA_BYTE0
0000 0000, RW
First byte of IP source address:
This field contains the most significant byte of the IP source address.
10.7.4 PHY Status Frame Configuration Register 3 (PSF_CFG3), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this
register is used as the second 16-bits of the IP Source address for an IPv4 PHY Status Frame.
Table 10-67. PHY Status Frame Configuration Register 3 (PSF_CFG3), address 0x17
Bit
Bit Name
Default
15:8
IP_SA_BYTE3
0000 0000, RW
Fourth byte of IP source address:
This field contains the fourth byte of the IP source address.
Description
7:0
IP_SA_BYTE2
0000 0000, RW
Third byte of IP source address:
This field contains the third byte of the IP source address.
10.7.5 PHY Status Frame Configuration Register 4 (PSF_CFG4), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this
register is used to assist in computation of the IP checksum for an IPv4 PHY Status Frame.
Table 10-68. PHY Status Frame Configuration Register 4 (PTP_PKTSTS4), address 0x18
Bit
Bit Name
Default
15:0
IP_CHKSUM
0000 0000 0000
0000, RW
Description
IP Checksum:
This field contains a precomputed value ones-complement addition of all fixed
values in the IP Header. The device will add the Total Length and Identification
values to generate the final checksum.
10.7.6 PTP SFD Configuration Register (PTP_SFDCFG), Page 6
This register provides configuration to enable outputting the RX and TX Start-of-Frame (SFD) signals on
GPIO pins. Note that GPIO assignments are not exclusive.
Table 10-69. PTP SFD Configuration Register (PTP_SFDCFG), address 0x19
Bit
Bit Name
Default
Description
15:8
RESERVED
0000 0000, RO
7:4
TX_SFD_GPIO
0000, RW
TX SFD GPIO Select:
This field controls the GPIO output to which the TX SFD signal is assigned. Valid
values are 0 (disabled) or 1-12.
3:0
RX_SFD_GPIO
0000, RW
RX SFD GPIO Select:
This field controls the GPIO output to which the RX SFD signal is assigned. Valid
values are 0 (disabled) or 1-12.
Reserved: Writes ignored, Read as 0
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
127
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
10.7.7 PTP Interrupt Control Register (PTP_INTCTL), Page 6
This register provides configuration for the IEEE 1588 interrupt function, allowing the PTP Interrupt to use
any of the GPIO pins.
Table 10-70. PTP Interrupt Control Register (PTP_INTCTL), address 0x1A
Bit
Bit Name
Default
15:4
RESERVED
0000 0000 0000,
RO
3:0
PTP_INT_GPIO
0000, RW
Description
Reserved: Writes ignored, Read as 0
PTP Interrupt GPIO Select:
To enable interrupts on a GPIO pin, this field should be set to the GPIO number.
Setting this field to 0 will disable interrupts via the GPIO pins.
10.7.8 PTP Clock Source Register (PTP_CLKSRC), Page 6
This register provides configuration for the reference clock source driving the IEEE 1588 logic. The source
clock period is also used by the 1588 clock nanoseconds adder to add the proper value every reference
clock cycle.
Table 10-71. PTP Clock Source Register (PTP_CLKSRC), address 0x1B
Bit
Bit Name
Default
Description
15:1
4
CLK_SRC
00, RW
13:7
RESERVED
00 0000 0, RO
Reserved: Writes ignored, Read as 0
6:0
CLK_SRC_PER
000 0000, RW
PTP Clock Source Period:
This field configures the PTP clock source period in nanoseconds. Values less than
8 are invalid and cannot be written; attempting to write a value less than 8 will cause
CLK_SRC_PER to be 8. When the clock source selection is the Divide-by-N from
the internal PGM, bits 6:3 are used as the N value; bits 2:0 are ignored in this mode.
PTP Clock Source Select:
Selects among three possible sources for the PTP reference clock:
00 : 125 MHz from internal PGM (default)
01 : Divide-by-N from 125 MHz internal PGM
1x : External reference clock
10.7.9 PTP Ethernet Type Register (PTP_ETR), Page 6
This register provides the Ethernet Type (Ethertype) field for PTP transport over Ethernet (Layer2).
Table 10-72. PTP Ethernet Type Register (PTP_ETR), address 0x1C
Bit
Bit Name
Default
Description
15:0
PTP_ETYPE
1111 0111 1000
1000, RW
PTP Ethernet Type:
This field contains the Ethernet Type field used to detect PTP messages transported
over Ethernet layer 2.
10.7.10 PTP Offset Register (PTP_OFF), Page 6
This register provides the byte offset to the PTP message in a Layer2 Ethernet frame.
Table 10-73. PTP Offset Register (PTP_OFF), address 0x1D
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
Reserved: Writes ignored, Read as 0
7:0
PTP_OFFSET
0000 0000, RO
PTP Offset:
This field contains the offset in bytes to the PTP Message from the preceding
header. For Layer2, this is the offset from the Ethernet Type Field. For UDP/IP, it is
the offset from the end of the UDP Header.
128
Description
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
DP83630
www.ti.com
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
10.7.11 PTP GPIO Monitor Register (PTP_GPIOMON), Page 6
This register provides read-only access to the current values on GPIO inputs.
Table 10-74. PTP GPIO Monitor Register (PTP_GPIOMON), address 0x1E
Bit
Bit Name
Default
15:12
RESERVED
0000, RO
11:0
PTP_GPIO_IN
0000 0000 0000,
RO
Description
Reserved: Writes ignored, Read as 0
PTP GPIO Inputs:
This field reflects the current values seen on the GPIO inputs. GPIOs 12 through 1
are mapped to bits 11:0 in order.
10.7.12 PTP Receive Hash Register (PTP_RXHASH), Page 6
This register provides configuration for the source identity hash filter of the PTP receive packet parser. If
enabled, the receive parse logic will deliver a receive timestamp only if the hash function on the ten octet
sourcePortIdentity field correctly matches the programmed value. The source identity hash filter does not
affect timestamp insertion.
Table 10-75. PTP Receive Hash Register (PTP_RXHASH), address 0x1F
Bit
Bit Name
Default
15:13
RESERVED
000, RO
12
RX_HASH_EN
0, RW
11:0
PTP_RX_HASH
0000 0000 0000,
RW
Description
Reserved: Writes ignored, Read as 0
Receive Hash Enable:
Enables filtering of PTP messages based on the hash function on the ten octet
sourcePortIdentity field.
Receive Hash:
This field contains the expected source identity hash value for incoming PTP event
messages.
Register Block
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
129
DP83630
SNLS335B – OCTOBER 2010 – REVISED APRIL 2013
www.ti.com
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (April 2013) to Revision B
•
130
Changed layout of National Data Sheet to TI format
Page
.........................................................................
Register Block
129
Copyright © 2010–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DP83630
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DP83630SQ/NOPB
ACTIVE
WQFN
RHS
48
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
DP83630SQ
DP83630SQE/NOPB
ACTIVE
WQFN
RHS
48
250
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
DP83630SQ
DP83630SQX/NOPB
ACTIVE
WQFN
RHS
48
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
DP83630SQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
DP83630SQ/NOPB
WQFN
RHS
48
DP83630SQE/NOPB
WQFN
RHS
DP83630SQX/NOPB
WQFN
RHS
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
1000
330.0
16.4
7.3
7.3
1.3
12.0
16.0
Q1
48
250
178.0
16.4
7.3
7.3
1.3
12.0
16.0
Q1
48
2500
330.0
16.4
7.3
7.3
1.3
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DP83630SQ/NOPB
WQFN
RHS
48
1000
367.0
367.0
38.0
DP83630SQE/NOPB
WQFN
RHS
48
250
213.0
191.0
55.0
DP83630SQX/NOPB
WQFN
RHS
48
2500
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
RHS0048A
SQA48A (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages