Mitsubishi FU-650SDF-FL49M12 1.55 î¼m dfb-ld module with singlemode fiber pigtail Datasheet

MAY06 (1/5)
MITSUBISHI (OPTICAL DEVICES)
FU-650SDF-Fx49Mxx
1.55 μm DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL
DESCRIPTION
Module type FU-650SDF-Fx49Mxx is a 1.5μm coaxial
Uncooled DFB-LD module with single-mode optical fiber.
This module is suitable for a light source of analog
applications such CATV return path.
FEATURES
l High liniality multi quantum wells (MQW) DFB-LD
l Emission wavelength is in 1.55μm band
l CWDM 8ch selectable
l Built-in optical isolator
l Coaxial package
l With photodiode for optical output monitor
APPLICATION
CATV return path
Analog transmission systems
ABSOLUTE MAXIMUM RATINGS (Tc=25°C)
Parameter
Symbol
Laser diode
Optical output power
Pf
Forward current
If
Reverse voltage
Vrl
Photodiode
Reverse voltage
Vrd
Forward current
Ifd
Operating case temperature
Tc
Storage temperature
Tstg
Conditions
CW
CW
-
Rating
10
150
2
20
2
-5 ~ +75
-40 ~ +85
Unit
mW
mA
V
V
mA
°C
°C
Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein
without notice. No liability is assumed as a result of their use or application.
MITSUBISHI CONFIDENTIAL
MAY06 (2/5)
MITSUBISHI (OPTICAL DEVICES)
FU-650SDF-Fx49Mxx
1.55 μm DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL
ELECTRICAL/OPTICAL CHARACTERISTICS
Parameter
Symbol
Threshold current
Optical output power
at threshold current
Operating current
Operating voltage
Modulation Current (Iop-Ith)
Deferential Efficiency
Ith
Pth
(Tc=25°C, unless otherwise noted)
Test Conditions
Min.
CW
CW, Ibias=Ith
-
Iop
Vop
Imod
η
CW, Pf=4mW
CW, Pf=4mW
CW, Pf=4mW
CW, Pf=4mW
Differential impedance
Optical output power from
fiber end
Light-emission central
wavelength
Rs
Pf
CW, nominal
λc
CW, APC
(Note 1)
Wavelength temperature
coefficient
Side mode suppression ratio
Tracking error (Note 2)
2nd order distortion
3rd order distortion
λct
CW, APC
Sr
Er
D2
D3
CW, APC
CW, APC
2 tone test (Note 3)
f1=13MHz, f2=19MHz
m=10%/tone, Pf=4mW
CW, APC, f=200MHz
Tc=25°C
Tc=75°C
-Fx49Mx1
-Fx49Mx2
-Fx49Mx3
-Fx49Mx4
-Fx49Mx5
-Fx49Mx6
-Fx49Mx7
-Fx49Mx8
Limits
Typ.
10
-
Unit
Max.
20
100
mA
μW
20
0.1
0.06
3
40
1.2
30
0.13
0.09
6
4
65
1.5
45
10
mA
V
mA
mA
1467
1487
1507
1527
1547
1567
1587
1607
-
1470
1490
1510
1530
1550
1570
1590
1610
0.1
1473
1493
1513
1533
1553
1573
1593
1613
0.11
nm
nm
nm
nm
nm
nm
nm
nm
nm/°C
30
-
45
0.5
-
1.25
-50
-60
dB
dB
dBc
Ω
mW
Relative intensity noise
Nr
-155
-145
dB/Hz
(Note 4)
2-tone, m=10%/tone
Spurious Noise (Carrier On)
NspON
-50
-45
dBc
Spurious Noise (Carrier Off)
NspOFF Imon=Imonop (Note 5)
-35
-25
dBc
Monitor current
Imon
CW, Pf=4mW, Vrd=5V
0.05
mA
Dark current (PD)
Id
Vrd=5V
0.1
μA
Capacitance (PD)
Ct
Vrd=5V, f=1MHz
10
pF
Note 1) “APC” represents operating LD by a constant monitor current for Pf=4mW at Tc=25°C.
Note 2) Er=max|10×log(Pf / Pf@25°C)|
Note 3) Optical return loss of the connectors should be greater than 40dB in order to get the specified performance.
Note 4) Relative intensity noise dose not includes shot noise of receiver.
Note 5) Spurious noise is defined under the following test condition.
2-tone carrier frequency
: f1=13MHz, f2=19MHz
Fiber length
: 15km
Measurement frequency
: 5~200MHz
Spectrum analyzer setting
: Resolution bandwidth 100kHz, video bandwidth 30kHz and 30 second
max hold.
FIBER PIGTAIL SPECIFICATIONS
Parameter
Limits
Type
SM
Mode field diameter
9.5+/-1
Cladding diameter
125+/-2
Secondary coating outer diameter
0.9+/-0.1
Lfiber(Note 6)
1000+/-100
Connector
See ordering information
Optical return loss of connector
See ordering information
Note 6) ‘Lfiber’ is the fiber length that is defined in OUTLINE DIAGRAM.
Unit
μm
μm
mm
mm
dB
Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein
without notice. No liability is assumed as a result of their use or application.
MITSUBISHI CONFIDENTIAL
MAY06 (3/5)
MITSUBISHI (OPTICAL DEVICES)
FU-650SDF-Fx49Mxx
1.55 μm DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL
ORDERING INFORMATION
FU - 650SDF – F _ 49M _ _
1
2
3
4
5
6
7
8
1
3
W
L
Wavelength (typ)
1470nm
1490nm
1510nm
1530nm
1550nm
1570nm
1590nm
1610nm
Flange type
Horizontal flange
Without flange
Connector
SC/PC
SC/APC
Return loss
40dB min
60dB min
Standard
Optional
Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein
without notice. No liability is assumed as a result of their use or application.
MITSUBISHI CONFIDENTIAL
MAY06 (4/5)
MITSUBISHI (OPTICAL DEVICES)
FU-650SDF-Fx49Mxx
1.55 μm DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL
OUTLINE DIAGRAM
FU-650SDF-Fx49M1x
FU-650SDF-Fx49M3x
Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein
without notice. No liability is assumed as a result of their use or application.
MITSUBISHI CONFIDENTIAL
MAY06 (5/5)
MITSUBISHI (OPTICAL DEVICES)
FU-650SDF-Fx49Mxx
1.55 μm DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL
Safety Cautions for Use of Optoelectronic Devices
General:
Although the manufacturer is always striving to improve the reliability of its product, problems and errors may occur with
semiconductor products. Therefore, the user's products are required to be designed with full safety regard to prevent any accidents that
results in injury, death, fire or environmental damage even when semiconductor products happen to error. Especially it is recommended
to take in consideration about redundancy, fire prevention, error prevention safeguards. And the following requirements must be strictly
observed.
Warning!
1. Eye safety : Seminductor laser radiates laser light during operation. Laser light is very dangerous when shot directly into human
eyes. Don't look at laser light directly, or through optics such as a lens. The laser light should be observed using the ITV camera, IRviewer, or other appropriate instruments.
2. Product handling : The product contains GaAs (gallium arsenide). It is safe for regular use, but harmful to the human body if
made into powder or steam. Be sure to avoid dangerous process like smashing, burning, chemical etching. Never put this product in
one's mouth or swallow it.
3. Product disposal : This product must be disposed of as special industrial waste. It is necessary to separate it from general
industrial waste and general garbage.
Handling Cautions for Optoelectronic Devices
1. General:
(1) The products described in this specification are designed and manufactured for use in general communication systems or
electronic devices, unless their applications or reliability are otherwise specified. Therefore, they are not designed or manufactured for
installation in devices or systems that may affect human life or that are used in social infrastructure requiring high reliability.
(2) When the customer is considering to use the products in special applications, such as transportation systems (automobiles, trains,
vessels), medical equipments, aerospace, nuclear power control, and submarine repeaters or systems, please contact Mitsubishi
Electric or an authorized distributor.
2. Shipping Conditions:
(1) During shipment, place the packing boxes in the correct direction, and fix them firmly to keep them immovable. Placing the boxes
upside down, tilting, or applying abnormal pressure onto them may cause deformation in the electrode terminals, breaking of optical
fiber, or other problems.
(2) Never throw or drop the packing boxes. Hard impact on the boxes may cause break of the devices.
(3) Take strict precautions to keep the devices dry when shipping under rain or snow.
3. Storage Conditions:
When storing the products, it is recommended to store them following the conditions described below without opening the packing. Not
taking enough care in storing may result in defects in electrical characteristics, soldering quality, visual appearance, and so on. The
main points are described below (if special storage conditions are given to the product in the specification sheet, they have priority over
the following general cautions):
(1) Appropriate temperature and humidity conditions, i.e., temperature range between 5~30°C, and humidity between 40~60 percent
RH, should be maintained in storage locations. Controlling the temperature and humidity within this range is particularly important in
case of long-term storage for six months or more.
(2) The atmosphere should be particularly free from toxic gases and dust.
(3) Do not apply any load on the product.
(4) Do not cut or bend the leads of the devices which are to be stored. This is to prevent corrosion in the cut or bent part of the lead
causing soldering problems in the customer’s assembling process.
(5) Sudden change in temperature may cause condensation in the product or packing, therefore, such locations should be avoided for
storing. Temperature in storage locations should be stable.
(6) When storing ceramic package products for extended periods of time, the leads may turn reddish due to reaction with sulfur in the
atmosphere.
(7) Storage conditions for bare chip and unsealed products shall be stated separately because bare chip and unsealed products
require stricter controls than package sealed products.
4. Design Conditions and Environment under Use:
(1) Avoid use in locations where water or organic solvents adhere directly to the product, or where there is any possibility of the
generation of corrosive gas, explosive gas, dust, salinity, or other troublesome conditions. Such environments will not only significantly
lower the reliability, but also may lead to serious accidents.
(2) Operation in excess of the absolute maximum ratings can cause permanent damage to the device. The customers are requested
to design not to exceed those ratings even for a short time.
5. ESD Safety Cautions:
The optoelectronic devices are sensitive to static electricity (ESD, electro-static discharge). The product can be broken by ESD. When
handling this product, please observe the following countermeasures:
<Countermeasures against Static Electricity and Surge>
To prevent break of devices by static electricity or surge, please adopt the following countermeasures in the assembly line:
(1) Ground all equipments, machinery jigs, and tools in the process line with earth wires installed in them. Take particular care with hot
plates, solder irons and other items for which the commercial power supplies are prone to leakage.
(2) Workers should always use earth bands. Use of antistatic clothing, electric conductive shoes, and other safety equipment while at
work is highly recommended.
(3) Use conductive materials for this product’s container, etc.
(4) It is recommended that grounding mats be placed on the surfaces of assembly line workbench and the surrounding floor in work
area, etc.
(5) When mounting this product in parts or materials which can be electrically charged (printed wiring boards, plastic products, etc.),
pay close attention to the static electricity in those parts. ESD may damage the product.
(6) Humidity in working environment should be controlled to be 40 percent RH or higher.
These countermeasures are most general, and there is a need to carefully confirm the line before starting mass production using this
product (in the trial production, etc.). It is extremely important to prevent surge, eliminate it rapidly, and prevent it from spreading.
Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein
without notice. No liability is assumed as a result of their use or application.
MITSUBISHI CONFIDENTIAL
Similar pages