Kingbright APFA2507LSURKSYKZGKC 2.5x0.7mm right angle smd chip led lamp Datasheet

2.5x0.7mm RIGHT ANGLE SMD CHIP LED
LAMP
Part Number: APFA2507LSURKSYKZGKC
ATTENTION
Hyper Red
Super Bright Yellow
Green
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 2.5x1.0x0.7mm right angle SMD LED, 0.7mm thick-
z The Hyper Red source color devices are made with
AlGaInP on GaAs substrate Light Emitting Diode.
ness.
z The Super Bright Yellow device is made with AlGaInP
z Low power consumption.
(on GaAs substrate) light emitting diode chip.
z Wide viewing angle.
z Ideal for backlight and indicator.
z The Green source color devices are made with InGaN
on Sapphire Light Emitting Diode.
z Package : 3000pcs / reel.
z Moisture sensitivity level : level 3.
z Tinned pads for improved solderability.
z Low current IF=2mA operating.
z Electrostatic discharge and power surge could damage
the LEDs.
z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs.
z RoHS compliant.
z All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
RED
YELLOW
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.15(0.006") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 1 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
Selection Guide
Part No.
Emitting Color (Material)
Iv (mcd) [2]
@ 2mA
Lens Type
Min.
Typ.
20
30
*6
*10
6
15
*6
*15
20
60
*20
*60
Hyper Red (AlGaInP)
APFA2507LSURKSYKZGKC
Water Clear
Super Bright Yellow (AlGaInP)
Green (InGaN)
Viewing
Angle [1]
2θ1/2
130°
115°
125°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Hyper Red
Super Bright Yellow
Green
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
645
590
515
nm
IF=2mA
Hyper Red
Super Bright Yellow
Green
630
590
525
nm
IF=2mA
Spectral Line Half-width
Hyper Red
Super Bright Yellow
Green
28
20
35
nm
IF=2mA
C
Capacitance
Hyper Red
Super Bright Yellow
Green
35
20
45
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Hyper Red
Super Bright Yellow
Green
1.75
1.85
2.65
2.5
2.5
4.1
V
IF=2mA
IR
Reverse Current
Hyper Red
Super Bright Yellow
Green
10
10
50
uA
VR=5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Hyper Red
Super Bright Yellow
Green
Units
Power dissipation
75
75
102.5
mW
DC Forward Current
30
30
25
mA
Peak Forward Current [1]
185
175
150
mA
Electrostatic Discharge Threshold (HBM)
3000
3000
450
V
Reverse Voltage
5
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
V
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 2 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
APFA2507LSURKSYKZGKC
Hyper Red
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 3 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
Super Bright Yellow
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 4 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
Green
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 5 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
APFA2507LSURKSYKZGKC
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 6 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
PACKING & LABEL SPECIFICATIONS
APFA2507LSURKSYKZGKC
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAO6074
REV NO: V.1A
DATE: NOV/25/2015
PAGE: 7 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.Q.Xie
ERP: 1203015273
Similar pages