MOTOROLA MPC106ARX83CG Pci bridge/memory controller Datasheet

Order Number: MPC106EC/D
Rev. 5, 8/2001
Semiconductor Products Sector
Technical Data
MPC106 PCI Bridge/Memory Controller
Hardware Specifications
The Motorola MPC106 PCI bridge/memory controller provides a PowerPC™ microprocessor common
hardware reference platform (CHRP™) compliant bridge between the PowerPC microprocessor family
and the Peripheral Component Interconnect (PCI) bus. In this document, the term ‘106’ is used as an
abbreviation for the phrase ‘MPC106 PCI bridge/memory controller.’ This document contains pertinent
physical characteristics of the 106. For functional characteristics, refer to the MPC106 PCI
Bridge/Memory Controller User’s Manual.
This document contains the following topics:
Topic
Section 1.1, “Overview”
Section 1.2, “Features”
Section 1.3, “General Parameters”
Section 1.4, “Electrical and Thermal Characteristics”
Section 1.5, “Pin Assignments”
Section 1.6, “Pinout Listings
Section 1.7, “Package Description”
Section 1.8, “System Design Information”
Section 1.9, “Document Revision History”
Section 1.10, “Ordering Information”
This document contains information on a new product under development by Motorola.
Motorola reserves the right to change or discontinue this product without notice.
© Motorola, Inc., 2001. All rights reserved.
Page
2
3
5
5
15
16
20
22
27
27
Overview
In this document, the term ‘60x’ is used to denote a 32-bit microprocessor from the PowerPC architecture
family that conforms to the bus interface of the PowerPC 601™, PowerPC 603™, or PowerPC 604™
microprocessors. Note that this does not include the PowerPC 602™ microprocessor which has a
multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is specified for
32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32
bits, and floating-point data types of 32 and 64 bits (single-precision and double-precision).
To locate any published errata or updates for this document, refer to the website at
http://www.mot.com/SPS/PowerPC/.
1.1 Overview
The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface
between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI
bus, and main memory. This section provides a block diagram showing the major functional units of the
106 and describes briefly how those units interact.
Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram
intended to show the basic features rather than how these features are physically implemented on the
device.
L2 Cache
Interface
Memory
Memory
Interface
60x Processor
Interface
L2
60x Bus
Power Management
Error/Interrupt
Control
Target
Master
PCI Interface
Configuration
Registers
PCI Bus
Figure 1. Block Diagram
2
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Features
The 106 provides a PowerPC microprocessor CHRP-compliant bridge between the PowerPC
microprocessor family and the PCI bus. CHRP documentation provides a set of specifications that define a
unified personal computer architecture. PCI support allows the rapid design of systems using peripherals
already designed for PCI and the other standard interfaces available in the personal computer hardware
environment. The 106 integrates secondary cache control and a high-performance memory controller, uses
an advanced, 3.3-V CMOS process technology, and is fully compatible with TTL devices.
The 106 supports a programmable interface to a variety of PowerPC microprocessors operating at select
bus speeds. The 60x address bus is 32 bits wide and the data bus is 64 bits wide. The 60x processor
interface of the 106 uses a subset of the 60x bus protocol, supporting single-beat and burst data transfers.
The address and data buses are decoupled to support pipelined transactions.
The 106 provides support for the following configurations of 60x processors and L2 cache:
•
•
•
Up to four 60x processors with no L2 cache
A single 60x processor plus a direct-mapped, lookaside L2 cache using the internal L2 cache
controller of the 106
Up to four 60x processors plus an externally controlled L2 cache (such as the Motorola MPC2605
integrated secondary cache)
The memory interface controls processor and PCI interactions to main memory and is capable of
supporting a variety of configurations using DRAM, EDO, SDRAM, ROM, or Flash ROM.
The PCI interface of the 106 complies with the PCI Local Bus Specification, Revision 2.1, and follows the
guidelines in the PCI System Design Guide, Revision 1.0, for host bridge architecture. The PCI interface
connects the processor and memory buses to the PCI bus, to which I/O components are connected. The PCI
bus uses a 32-bit multiplexed address/data bus, plus various control and error signals.
The PCI interface of the 106 functions as both a master and target device. As a master, the 106 supports
read and write operations to the PCI memory space, the PCI I/O space, and the PCI configuration space.
The 106 also supports PCI special-cycle and interrupt-acknowledge commands. As a target, the 106
supports read and write operations to system memory.
The 106 provides hardware support for four levels of power reduction: doze, nap, sleep, and suspend. The
design of the MPC106 is fully static, allowing internal logic states to be preserved during all power-saving
modes.
1.2 Features
This section summarizes the major features of the 106, as follows:
•
60x processor interface
— Supports up to four 60x processors
— Supports various operating frequencies and bus divider ratios
— 32-bit address bus, 64-bit data bus
— Supports full memory coherency
— Supports optional 60x local bus slave
— Decoupled address and data buses for pipelining of 60x accesses
— Store gathering on 60x-to-PCI writes
MPC106 PCI Bridge/Memory Controller Hardware Specifications
3
Features
4
•
Secondary (L2) cache control
— Configurable for write-through or write-back operation
— Supports cache sizes of 256 Kbytes, 512 Kbytes, and 1 Mbyte
— Up to 4 Gbytes of cacheable space
— Direct-mapped
— Supports byte parity
— Supports partial update with external byte decode for write enables
— Programmable interface timing
— Supports pipelined burst, synchronous burst, or asynchronous SRAMs
— Alternately supports an external L2 cache controller or integrated L2 cache module
•
Memory interface
— 1 Gbyte of RAM space, 16 Mbytes of ROM space
— Supports parity or error checking and correction (ECC)
— High-bandwidth, 64-bit data bus (72 bits including parity or ECC)
— Supports fast page mode DRAMs, extended data out (EDO) DRAMs, and synchronous
DRAMs (SDRAMs)
— Supports 1 to 8 banks of DRAM/EDO/SDRAM with sizes ranging from 2 Mbyte to
128 Mbytes per bank
— ROM space may be split between the PCI bus and the 60x/memory bus (8 Mbytes each)
— Supports 8-bit asynchronous ROM or 64-bit burst-mode ROM
— Supports writing to Flash ROM
— Configurable external buffer control logic
— Programmable interface timing
•
PCI interface
— Compliant with PCI Local Bus Specification, Revision 2.1
— Supports PCI interlocked accesses to memory using LOCK signal and protocol
— Supports accesses to all PCI address spaces
— Selectable big- or little-endian operation
— Store gathering on PCI writes to memory
— Selectable memory prefetching of PCI read accesses
— Only one external load presented by the MPC106 to the PCI bus
— Interface operates at 20–33 MHz
— Word parity supported
— 3.3 V/5.0 V-compatible
•
•
Support for concurrent transactions on 60x and PCI buses
Power management
— Fully-static 3.3-V CMOS design
— Supports 60x nap, doze, and sleep power management modes and suspend mode
•
•
IEEE 1149.1-compliant, JTAG boundary-scan interface
304-pin ceramic ball grid array (CBGA) package
MPC106 PCI Bridge/Memory Controller Hardware Specifications
General Parameters
1.3 General Parameters
The following list provides a summary of the general parameters of the 106:
Technology
0.5 µm CMOS, four-layer metal
Die size
5.8 mm x 7.2 mm (41.8 mm2)
Transistor count
250,000
Logic design
Fully-static
Packages
Surface mount 304-lead C4 ceramic ball grid array (CBGA)
Power supply
3.3 V ± 5% V DC
Maximum input rating
5.0 V ± 10% V DC
1.4 Electrical and Thermal Characteristics
This section provides both the AC and DC electrical specifications and thermal characteristics for the 106.
1.4.1 DC Electrical Characteristics
The tables in this section describe the 106 DC electrical characteristics. Table 1 provides the absolute
maximum ratings. Functional and tested operating conditions are given in Table 2. Absolute maximum
ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses
beyond those listed may affect device reliability or cause it permanent damage.
Table 1. Absolute Maximum Ratings
Characteristic
Symbol
Value
Unit
Notes
Supply voltage
Vdd
–0.3 to 3.6
V
—
PLL supply voltage
AVdd
–0.3 to 3.6
V
—
Vin
–0.3 to 5.5
V
1
Tj
0 to 105
°C
2
Tstg
–55 to 150
°C
—
Input voltage
Junction temperature
Storage temperature range
Notes:
1
2
Caution: Vin must not exceed Vdd by more than 2.5 V at all times including during power-on reset.
The extended temperature parts have die junction temperature of -40 to 105°C. See MPC106ARXTGPNS/D for
more information.
Table 2 provides the recommended operating conditions for the 106. Proper device operation outside of
these recommended and tested conditions is not guaranteed.
MPC106 PCI Bridge/Memory Controller Hardware Specifications
5
Electrical and Thermal Characteristics
Table 2. Recommended Operating Conditions
Characteristic
Symbol
Value
Unit
Notes
Supply voltage
Vdd
3.3 ± 165 mv
V
—
PLL supply voltage
AVdd
3.3 ± 165 mv
V
—
Vin
0 to 5.5
V
—
Tj
0 to 105
°C
Input voltage
Die junction temperature
The extended temperature parts have die junction
temperature of -40 to 105°C
Table 3 provides the package thermal characteristics for the 106.
Table 3. Package Thermal Characteristics
Characteristic
CBGA package thermal resistance, junction-to-top of die
Symbol
Value
Rating
θJC
0.133
°C/W
Note: Refer to Section 1.8, “System Design Information,” for more details about thermal management.
Table 4 provides the DC electrical characteristics for the 106, assuming Vdd = AVdd = 3.3 ± 5% V DC,
GND = 0 V DC, and 0 ≤ Tj ≤ 105 °C.
Table 4. DC Electrical Specifications
Characteristic
Symbol
Min
Max
Unit
Input high voltage (all inputs except SYSCLK)
VIH
2
5.5
V
Input low voltage (all inputs except SYSCLK)
VIL
GND
0.8
V
CVIH
2.4
5.5
V
CVIL
GND
0.4
V
Iin
—
15.0
µA
ITSI
—
15.0
µA
VOH
2.4
—
V
VOL
—
0.5
V
VOH
2.7
—
V
VOL
—
0.3
V
Cin
—
7.0
pF
SYSCLK input high voltage
SYSCLK input low voltage
Input leakage current, Vin =3.3
V1
Hi-Z (off-state) leakage current, Vin = 3.3
Output high voltage, IOH = -7
V1
mA2
Output low voltage, IOL = 7 mA2
PCI 3.3 V signaling output high voltage, IOH = -0.5
PCI 3.3 V signaling output low voltage, IOL = 1.5
Capacitance, Vin = 0 V, f = 1
mA2
mA2
MHz3
Notes:
1 Excludes test signals (LSSD_MODE and JTAG signals).
2 This value represents worst case 40-ohm drivers (default value for Processor/L2 control signals CI, WT, GBL, TBST,
TSIZ[0–2], TT[0–4], TWE, and TV) only. Other signals have lower default driver impedance and will support larger
IOH and IOL. All drivers may optionally be programmed to different driver strengths.
3 Capacitance is periodically sampled rather than 100% tested.
Table 5 lists the power consumption of the 106.
6
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Electrical and Thermal Characteristics
Table 5. Power Consumption
Mode
SYSCLK/Core
33/66 MHz
SYSCLK/Core
33/83.3 MHz
Unit
Typical
1.2
2.2
W
1.4
2.4
W
1.0
1.1
W
1.2
1.4
W
1.0
1.1
W
1.2
1.4
W
260
330
mW
360
450
mW
140
220
mW
190
270
mW
Full-On
Maximum
Doze
Typical
Maximum
Nap
Typical
Maximum
Sleep
Typical
Maximum
Suspend
Typical
Maximum
Notes:
• Power consumption for common system configurations assuming 50 pF loads
• Suspend power-saving mode assumes SYSCLK off and PLL in bypass mode.
• Typical power is an average value measured at Vdd = AVdd = 3.30 V and TA = 25 °C.
• Maximum power is measured at Vdd = AVdd = 3.45 V and TA = 25 °C.
1.4.2 AC Electrical Characteristics
This section provides AC electrical characteristics for the 106. After fabrication, parts are sorted by
maximum 60x processor bus frequency, as shown in Section 1.4.2.1, “Clock AC Specifications,” and tested
for conformance to the AC specifications for that frequency. These specifications are for operation between
16.67 and 33.33 MHz PCI bus (SYSCLK) frequencies. The 60x processor bus frequency is determined by
the PCI bus (SYSCLK) frequency and the settings of the PLL[0–3] signals. All timings are specified
relative to the rising edge of SYSCLK.
1.4.2.1 Clock AC Specifications
Table 6 provides the clock AC timing specifications as shown in Figure 2, and assumes Vdd = AVdd = 3.3
± 5% V DC, GND = 0 V DC, and 0 ≤ Tj ≤ 105 °C.
MPC106 PCI Bridge/Memory Controller Hardware Specifications
7
Electrical and Thermal Characteristics
Table 6. Clock AC Timing Specifications
Num
SYSCLK/Core
33/66 MHz
SYSCLK/Core
33/83.3 MHz
Min
Max
Min
Max
16.67
66
16.67
120
200
Characteristic
Unit
Notes
83.3
MHz
1
120
200
MHz
1, 2
—
60x processor bus (core) frequency
—
VCO frequency
—
SYSCLK frequency
16.67
33.33
16.67
33.33
MHz
1
1
SYSCLK cycle time
30.0
60.0
30.0
60.0
ns
—
SYSCLK rise and fall time
—
2.0
—
2.0
ns
3
4
SYSCLK duty cycle measured at 1.4 V
40
60
40
60
%
4
—
SYSCLK jitter
—
±200
—
±200
ps
5
—
106 internal PLL relock time
—
100
—
100
µs
4, 6
2, 3
Notes:
1 Caution: The SYSCLK frequency and PLL[0–3] settings must be chosen such that the resulting SYSCLK (bus)
frequency, CPU (core) frequency, and PLL (VCO) frequency do not exceed their respective maximum or minimum
operating frequencies. Refer to the PLL[0–3] signal description in Section 1.8, “System Design Information,” for
valid PLL[0–3] settings, and to Section 1.9, “Document Revision History,” for available frequencies and part
numbers.
2 VCO operating range for extended temperature devices is different. Refer to MPC106ARXTGPNS/D for more
information.
3 Rise and fall times for the SYSCLK input are measured from 0.4 V to 2.4 V.
4 Timing is guaranteed by design and characterization and is not tested.
5 The total input jitter (short-term and long-term combined) must be under ±200 ps.
6 PLL-relock time is the maximum time required for PLL lock after a stable Vdd, AVdd, and SYSCLK are reached
during the power-on reset sequence. This specification also applies when the PLL has been disabled and
subsequently re-enabled during the sleep and suspend power-saving modes. Also note that HRST must be held
asserted for a minimum of 255 bus clocks after the PLL-relock time (100 µs) during the power-on reset sequence.
Figure 2 provides the SYSCLK input timing diagram.
1
2
4
SYSCLK
VM
4
VM
3
CVIH
VM
CVIL
VM = Midpoint Voltage (1.4 V)
Figure 2. SYSCLK Input Timing Diagram
1.4.2.2 Input AC Specifications
Table 7 provides the input AC timing specifications for the 106 as defined in Figure 3 and Figure 4. These
specifications are for operation between 16.67 and 33.33 MHz PCI bus clock (SYSCLK) frequencies.
Assume Vdd = AVdd = 3.3 ± 5% V DC, GND = 0 V DC, and 0 ≤ Tj ≤ 105 °C.
8
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Electrical and Thermal Characteristics
Table 7. Input AC Timing Specifications
66 MHz
Num
83.3 MHz
Characteristic
Min
Max
Min
Unit
Notes
Max
10a Group I input signals valid to 60x Bus Clock (input setup)
4.0
3.5
ns
1,2,3
10a Group II input signals valid to 60x Bus Clock (input setup)
3.5
3.5
ns
1,2,4
10a Group III input signals valid to 60x Bus Clock (input setup)
3.0
2.5
ns
1,2,5
10a Group IV input signals valid to 60x Bus Clock (input setup)
5.0
4.0
ns
1,2,6
10b Group V input signals valid to SYSCLK (input setup)
7.0
7.0
ns
7,8
10b Group VI input signals valid to SYSCLK (input setup)
7.0
7.0
ns
7,9
11a 60x Bus Clock to group I–IV inputs invalid (input hold)
0
—
0
—
ns
3,4,5,6
–0.5
—
–0.5
—
ns
8,9
255 x
tsysclk +
100 µs
—
255 x
tsysclk +
100 µs
—
10c Mode select inputs valid to HRST (input setup)
3 x tsysclk
—
3 x tsysclk
—
ns
10,
11,12
11c HRST to mode select input invalid (input hold)
1.0
—
1.0
—
ns
10, 12
11b SYSCLK to group V–VI inputs invalid (input hold)
HRST pulse width
—
Notes:
Input specifications are measured from the TTL level (0.8 or 2.0 V) of the signal in question to the 1.4 V of the rising
edge of SYSCLK. Both input and output timings are measured at the pin (see Figure 3).
2 Processor and memory interface signals are specified from the rising edge of the 60x bus clock (which is internally
synchronized to SYSCLK).
3 Group I input signals include the following processor, L2, and memory interface signals: A[0–31], PAR[0–7]/AR[1–8],
BR[0–4], BRL2, XATS, LBCLAIM, ADS, BA0, TV and HIT (when configured for external L2)
4 Group II input signals include the following processor and memory interface signals: TBST, TT[0–4], TSIZ[0–2], WT,
CI, GBL, AACK, and TA.
5 Group III input signals include the following processor and memory interface signals: DL[0–31] and DH[0–31].
6 Group IV input signals include the following processor and L2 interface signals: TS, ARTRY, DIRTY_IN, and HIT
(when configured for internal L2 controller).
7 PCI 3.3 V signaling environment signals are measured from 1.65 V (Vdd ÷ 2) on the rising edge of SYSCLK to
VOH = 3.0 V or VOL = 0.3 V. PCI 5 V signaling environment signals are measured from 1.65 V (Vdd ÷ 2) on the rising
edge of SYSCLK to VOH = 2.4 V or VOL = 0.55 V.
8 Group V input signals include the following bussed PCI interface signals: FRAME, C/BE[0–3], AD[0–31], DEVSEL,
IRDY, TRDY, STOP, PAR, PERR, SERR, LOCK, FLSHREQ, and ISA_MASTER.
9 Group VI input signal is the point-to-point PCI GNT input signal.
10 The setup and hold time is with respect to the rising edge of HRST (see Figure 4). Mode select inputs include the
RCS0, FOE, and DBG0 configuration inputs.
11 t
sysclk is the period of the external clock (SYSCLK) in nanoseconds (ns). When the unit is given as tsysclk, the
numbers given in the table must be multiplied by the period of SYSCLK to compute the actual time duration (in
nanoseconds) of the parameter in question.
12 These values are guaranteed by design and are not tested.
1
Figure 3 provides the input timing diagram for the 106.
MPC106 PCI Bridge/Memory Controller Hardware Specifications
9
Electrical and Thermal Characteristics
60x Bus Clock
VM
10a
11a
Group I, II, III,
and IV INPUTS
SYSCLK
VM
10b
11b
Group V and
VI INPUTS
VM = Midpoint Voltage (1.4 V)
Figure 3. Input Timing Diagram
Figure 4 provides the mode select input timing diagram for the 106.
HRST
VM
10c
11c
MODE PINS
VM = Midpoint Voltage (1.4 V)
Figure 4. Mode Select Input Timing Diagram
1.4.2.3 Output AC Specifications
Table 8 provides the output AC timing specifications for 106 (shown in Table 5). Assume Vdd = AVdd =
3.3 ± 5% V DC, GND = 0 V DC, CL = 50 pF, and 0 ≤ Tj ≤ 105 °C. Processor and memory interface signals
are specified from the rising edge of the 60x bus clock (which is internally synchronized to SYSCLK). All
units are nanoseconds.
10
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Electrical and Thermal Characteristics
Table 8. Output AC Timing Specifications
66 MHz
Num
83.3 MHz
Characteristic
Notes
Min
Max
Min
Max
2.0
—
2.0
—
1
13a SYSCLK to output valid for TS and
ARTRY
—
7.0
—
6.0
2, 3, 4
13b SYSCLK to output valid for all non-PCI
signals except TS, ARTRY, RAS[0–7],
CAS[0–7], and DWE[0-2]
—
7.0
—
6.0
2, 3, 5
14a SYSCLK to output valid (for RAS[0–7]
and CAS[0–7])
—
7.0
—
6.0
2, 3
14b SYSCLK to output valid for PCI signals
—
11.0
—
11.0
3, 6
15a SYSCLK to output invalid for all
non-PCI signals (output hold)
1.0
—
1.0
—
7, 10
15b SYSCLK to output invalid for PCI
signals (output hold)
1.0
—
1.0
—
7
18
SYSCLK to ARTRY high impedance
before precharge (output hold)
—
8.0
—
8.0
1
19
SYSCLK to ARTRY precharge enable
(0.4 *
tsysclk) + 2.0
—
(0.4 x
tsysclk) + 2.0
—
8, 1
21
SYSCLK to ARTRY high impedance
after precharge
—
(1.5 *
tsysclk) + 8.0
—
(1.5 x
tsysclk) + 8.0
8, 1
12
SYSCLK to output driven (output
enable time)
Notes:
These values are guaranteed by design and are not tested.
2 Output specifications are measured from 1.4 V on the rising edge of the appropriate clock to the TTL level (0.8
V or 2.0 V) of the signal in question. Both input and output timings are measured at the pin (see Figure 5).
3 The maximum timing specification assumes C = 50 pF.
L
4 The shared outputs TS and ARTRY require pull-up resistors to hold them negated when there is no bus master
driving them.
5 When the 106 is configured for asynchronous L2 cache SRAMs, the DWE[0–2] signals have a maximum
SYSCLK to output valid time of (0.5 x tPROC) + 8.0 ns (where tPROC is the 60x bus clock cycle time).
6 PCI 3.3 V signaling environment signals are measured from 1.65 V (Vdd ÷ 2) on the rising edge of SYSCLK to
VOH = 3.0 V or VOL = 0.3 V.
7 The minimum timing specification assumes C = 0 pF.
L
8 t
sysclk is the period of the external bus clock (SYSCLK) in nanoseconds (ns). When the unit is given as tsysclk the
numbers given in the table must be multiplied by the period of SYSCLK to compute the actual time duration (in
nanoseconds) of the parameter in question.
9 PCI devices which require more than the PCI-specified hold time of T = 0ns or systems where clock skew
h
approaches the PCI-specified allowance of 2ns may not work with the MPC106. For workarounds, see Motorola
application note Designing PCI 2.1-Compliant MPC106 Systems (order number AN1727/D).
1
MPC106 PCI Bridge/Memory Controller Hardware Specifications
11
Electrical and Thermal Characteristics
Figure 5 provides the output timing diagram for the 106.
VM
VM
VM
60x Bus Clock
13b
15a
14
ALL Non-PCI
OUTPUTS
(Except TS and
ARTRY)
16
12
15a
13
16
13a
TS
21
19
18
ARTRY
VM
VM
SYSCLK
14
15b
12
ALL
PCI OUTPUTS
VM = Midpoint Voltage (1.4V)
Figure 5. Output Timing Diagram
1.4.3 JTAG AC Timing Specifications
Table 9 provides the JTAG AC timing specifications. Assume Vdd = AVdd = 3.3 ± 5% V DC, GND = 0 V
DC, CL = 50 pF, and 0 ≤ Tj ≤ 105 °C.
Table 9. JTAG AC Timing Specifications (Independent of SYSCLK)
Num
12
Characteristic
Min
Max
Unit
Notes
—
TCK frequency of operation
0
25
MHz
—
1
TCK cycle time
40
—
ns
—
2
TCK clock pulse width measured at 1.4 V
20
—
ns
—
3
TCK rise and fall times
0
3
ns
1
4
TRST setup time to TCK rising edge
10
—
ns
2
5
TRST assert time
10
—
ns
1
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Electrical and Thermal Characteristics
Table 9. JTAG AC Timing Specifications (Independent of SYSCLK) (Continued)
Num
Characteristic
Min
Max
Unit
Notes
6
Boundary-scan input data setup time
5
—
ns
3
7
Boundary-scan input data hold time
15
—
ns
3
8
TCK to output data valid
0
30
ns
4
9
TCK to output high impedance
0
30
ns
4
10
TMS, TDI data setup time
5
—
ns
—
11
TMS, TDI data hold time
15
—
ns
1
12
TCK to TDO data valid
0
15
ns
—
13
TCK to TDO high impedance
0
15
ns
—
Notes:
These values are guaranteed by design, and are not tested
2 TRST is an asynchronous signal. The setup time is for test purposes only.
3 Non-test signal input timing with respect to TCK.
4 Non-test signal output timing with respect to TCK.
1
Figure 6 provides the JTAG clock input timing diagram.
1
2
2
VM
TCK
3
VM
VM
3
VM = Midpoint Voltage (1.4 V)
Figure 6. JTAG Clock Input Timing Diagram
Figure 7 provides the TRST timing diagram.
TCK
4
TRST
5
Figure 7. TRST Timing Diagram
MPC106 PCI Bridge/Memory Controller Hardware Specifications
13
Electrical and Thermal Characteristics
Figure 8 provides the boundary-scan timing diagram.
TCK
6
Data Inputs
7
Input Data Valid
8
Data Outputs
Output Data Valid
9
Data Outputs
8
Data Outputs
Output Data Valid
Figure 8. Boundary-Scan Timing Diagram
Figure 9 provides the test access port timing diagram.
TCK
10
TDI, TMS
11
Input Data Valid
12
TDO
Output Data Valid
13
TDO
12
TDO
Output Data Valid
Figure 9. Test Access Port Timing Diagram
14
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Pin Assignments
1.5 Pin Assignments
Figure 10 contains the pin assignments for the MPC106, and Figure 11 provides a key to the shading.
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
W
DL26
DL28
DL30
DH31
DH29
DH27
DH25
DH23
DH21
DH19
DH17
DH15
DH13
DH11
DH9
DH7
W
V
DL24
DL27
DL29
DL31
DH30
DH28
DH26
DH24
DH20
DH18
DH16
DH14
DH12
DH10
DH8
DL22
V
U
MA1/
SDBA0/
AR9
DL23
DL25
DL14
PLL2
PLL0
DL12
DL10
DL4
DL2
DL0
DOE/
DBGL2
TOE
DBG1
DH6
DL21
DL20
U
T
MA2/
SDMA2/
AR10
WE
DH0
DL15
PLL3
PLL1
DL13
DL11
DL3
DL1
TV/
BR2
BA0/
BR3
HIT
DIRTY_IN/
BR1
DL19
DCS/
BG3
T
R
MA3/
SDMA3/
AR11
RCS0
DH2
DH1
DL16
Vss
Vdd
DL9
DL5
Vss
Vdd
TWE/
BG2
DIRTY_OUT/
BG1
ADS/
DALE/
BRL2
A0
TS
R
P
MA5/
SDMA5/
AR13
MA4/
SDMA4/
AR12
DH4
DH3
Vss
Vdd
Vss
DL8
DL6
Vdd
Vss
Vdd
BA1/
BAA/
BGL2
DWE0/
DBG2
A1
XATS/SDMA
1
P
N
MA6/
SDMA6/
AR14
MA0/
SDBA1/
SDMA0/
AR0
DL17
DH5
Vdd
Vss
Vdd
DL7
DH22
Vss
Vdd
Vss
LBCLAIM
CI
A2
TA
N
M
MA8/
SDMA8/
AR16
MA7/
SDMA7/
AR15
RAS0/
CS0
DL18
Vss
Vdd
Vss
NC
NC
Vdd
Vss
Vdd
WT
GBL
A3
TT4
M
L
HRST
MA9/
SDMA9/
AR17
QACK
RAS1/
CS1
Vdd
CKO/
DWE2
RAS5/
CS5
Vss
Vdd
Vss
SYSCLK
DBG0
TBST
BR0
A4
TT3
L
K
MA11/
SDMA11/
AR19
MA10/
SDMA10/
AR18
RAS3/
CS3
RAS2/
CS2
RAS4/
CS4
RAS7/
CS7
Vdd
AVdd
Vss
Vdd
A9
A8
A7
BG0
A5
TT2
K
J
MA12/
SDMA12/
AR20
CAS0/
DQM0
PPEN
RCS1
RAS6/
CS6
MCP
DBGLB/
CKE
Vss
Vdd
Vss
A11
A6
A13
A12
A10
TEA
J
H
QREQ
CAS1/
DQM1
SUSPEND
TRST
Vss
DWE1/
DBG3
PIRQ/
SDRAS
NC
NC
Vdd
Vss
Vdd
A15
A14
A16
TT1
H
G
CAS2/
DQM2
RTC
CAS4/
DQM4
CAS5/
DQM5
Vdd
LSSD_MODE
Vdd
PAR
LOCK
Vss
Vdd
Vss
TSIZ1
TSIZ0
A17
TT0
G
F
BCTL0
BCTL1
CAS6/
DQM6
TCK
Vss
Vdd
Vss
PERR
DEVSEL
Vdd
Vss
Vdd
A21
TSIZ2
ARTRY
A18
F
E
CAS3/
DQM3
NMI
CAS7/
DQM7
MDLE/
SDCAS
TDO
Vss
Vdd
SERR
IRDY
Vss
Vdd
A31
A29
A22
A20
A19
E
D
PAR0/
AR1
PAR1/
AR2
TMS
FOE
AD28
AD24
AD21
AD17
AD14
AD10
C/BE0
AD4
AD0
A30
AACK
A23
D
C
PAR2/
AR3
PAR3/
AR4
PAR5/
AR6
AD30
AD26
AD23
AD19
C/BE2
C/BE1
AD12
AD8
AD6
AD2
A27
A25
A24
C
B
PAR4/
AR5
PAR7/
AR8
AD1
TDI
AD7
AD11
AD15
TRDY
AD18
AD22
AD25
AD29
REQ
ISA_MASTER/
BERR
A28
A26
B
A
PAR6/
AR7
GNT
AD3
AD5
AD9
AD13
FRAME
STOP
AD16
AD20
C/BE3
AD27
AD31
FLSHREQ
MEMACK
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
A
1
Figure 10. Pin Assignments
NC
No Connect
Vdd
Power Supply Positive
Vss
Power Supply Ground
AVdd
Clock Power Supply Positive (K9)
VIEW
Signals
Figure 11. Pin Assignments Shading Key
MPC106 PCI Bridge/Memory Controller Hardware Specifications
15
Pinout Listings
1.6 Pinout Listings
Table 10 provides the pinout listing for the MPC106. Some signals have dual functions and are shown
more than once.
Table 10. Pinout Listing
Signal Name
Pin Number
Active
I/O
R2, P2, N2, M2, L2, K2, J5, K4, K5, K6, J2, J6, J3, J4, H3,
H4, H2, G2, F1, E1, E2, F4, E3, D1, C1, C2, B1, C3, B2, E4,
D3, E5
High
I/O
AACK
D2
Low
I/O
ARTRY
F2
Low
I/O
BG0
K3
Low
Output
BG1
(DIRTY_OUT)
R4
Low
Output
BG2
(TWE)
R5
Low
Output
BG3
(DCS)
T1
Low
Output
BR0
L3
Low
Input
BR1
(DIRTY_IN)
T3
Low
Input
BR2
(TV)
T6
Low
Input
BR3
(BA0)
T5
Low
Input
CI
N3
Low
I/O
DBG0
L5
Low
Output
DBG1
(TOE)
U4
Low
Output
DBG2
(DWE0)
P3
Low
Output
DBG3
(DWE1)
H11
Low
Output
DBGLB
(CKE)
J10
Low
Output
DH[0–31]
T14, R13, R14, P13, P14, N13, U3, W1, V2, W2, V3, W3, V4,
W4, V5, W5, V6, W6, V7, W7, V8, W8, N8, W9, V9, W10, V10,
W11, V11, W12, V12, W13
High
I/O
DL[0–31]
U6, T7, U7, T8, U8, R8, P8, N9, P9, R9, U9, T9, U10, T10,
U13, T13, R12, N14, M13, T2, U1, U2, V1, U15, V16, U14,
W16, V15, W15, V14, W14, V13
High
I/O
M3
Low
I/O
60x Processor Interface Signals
A[0–31]
GBL
16
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Pinout Listings
Table 10. Pinout Listing (Continued)
Signal Name
Pin Number
Active
I/O
LBCLAIM
N4
Low
Input
MCP
J11
Low
Output
TA
N1
Low
I/O
TBST
L4
Low
I/O
TEA
J1
Low
Output
TS
R1
Low
I/O
G3, G4, F3
High
I/O
G1, H1, K1, L1, M1
High
I/O
WT
M4
Low
I/O
XATS
(SDMA1)
P1
Low
Input
TSIZ[0–2]
TT[0–4]
L2 Cache Interface Signals
ADS/DALE/BRL2
R3
Low
I/O
BA0
(BR3)
T5
Low
Output
BA1/BAA/BGL2
P4
Low
Output
DBGL2/DOE
U5
Low
Output
DCS
(BG3)
T1
Low
Output
DIRTY_IN
(BR1)
T3
Low
Input
DIRTY_OUT
(BG1)
R4
Low
Output
DWE0
(DBG2)
P3
Low
Output
DWE1
(DBG3)
H11
Low
Output
DWE2
(CKO)
L11
Low
Output
HIT
T4
Low
Input
TOE
(DBG1)
U4
Low
Output
TV
(BR2)
T6
High
I/O
TWE
(BG2)
R5
Low
Output
F16, F15
Low
Output
B3
Low
Input
Memory Interface Signals
BCTL[0–1]
BERR
(ISA_MASTER)
MPC106 PCI Bridge/Memory Controller Hardware Specifications
17
Pinout Listings
Table 10. Pinout Listing (Continued)
Signal Name
Active
I/O
J15, H15, G16, E16, G14, G13, F14, E14
Low
Output
CKE/DBGLB
J10
High
Output
FOE
D13
Low
Output
MA0/SDBA1/SDMA0/AR0 N15
High
Output
P1
High
Output
U16
High
Output
High
Output
E13
Low
Output
D16, D15, C16, C15, B16, C14, A16, B15
High
I/O
J14
Low
Output
M14, L13, K13, K14, K12, L10, J12, K11
Low
Output
RCS0
R15
Low
I/O
RCS1
J13
Low
Output
RTC
G15
High
Input
SDRAS
(PIRQ)
H10
Low
Output
WE
T15
Low
Output
AD[31–0]
A4, C13, B5, D12, A5, C12, B6, D11, C11, B7, D10, A7, C10,
B8, D9, A8, B10, D8, A11, C7, B11, D7, A12, C6, B12, C5,
A13, D5, A14, C4, B14, D4
High
I/O
C/BE[3–0]
A6, C9, C8, D6
Low
I/O
DEVSEL
F8
Low
I/O
FLSHREQ
A3
Low
Input
FRAME
A10
Low
I/O
GNT
A15
Low
Input
IRDY
E8
Low
I/O
ISA_MASTER
(BERR)
B3
Low
Input
LOCK
G8
Low
Input
MEMACK
A2
Low
Output
PAR
G9
High
I/O
PERR
F9
Low
I/O
H10
Low
Output
B4
Low
Output
CAS/DQM[0–7]
SDMA1
(XATS)
MA1/SDBA0/AR9
Pin Number
MA[2–12]/SDMA[2–12]/AR T16, R16, P15, P16, N16, M15, M16, L15, K15, K16, J16
[10–20]
MDLE/SDCAS
PAR[0–7]/AR[1–8]
PPEN
RAS/CS[0–7]
PCI Interface Signals1
PIRQ
(SDRAS)
REQ
18
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Pinout Listings
Table 10. Pinout Listing (Continued)
Signal Name
Pin Number
Active
I/O
SERR
E9
Low
I/O
STOP
A9
Low
I/O
TRDY
B9
Low
I/O
Interrupt, Clock, and Power Management Signals
CKO
(DWE2)
L11
High
Output
HRST
L16
Low
Input
NMI
E15
High
Input
QACK
L14
Low
Output
QREQ
H16
Low
Input
Clock
Input
Low
Input
U11, T11, U12, T12
High
Input
TCK
F13
Clock
Input
TDI
B13
High
Input
TDO
E12
High
Output
TMS
D14
High
Input
TRST
H13
Low
Input
K9
High
Clock
Power
G11
Low
Input
Vdd
E10, E6, F11, F5, F7, G10, G12, G6, H5, H7, K10, K7, L12,
M11, M5, M7, N10, N12, N6, P11, P5, P7, R10, R6, J8, L8
High
Power
Vss
E11, E7, F10, F12, F6, G5, G7, H12, H6, J7, L7, M10, M12,
M6, N11, N5, N7, P10, P12, P6, R11, R7, K8, J9, L9
Low
Ground
NC
H8, H9, M8, M9
—
—
SYSCLK
SUSPEND
L6
H14
Test/Configuration Signals
PLL[0–3]
Power and Ground Signals
AVdd
LSSD_MODE 2
Note:
1 All PCI signals are in little-endian bit order.
2 This test signal is for factory use only. It must be pulled up to Vdd for normal device operation.
MPC106 PCI Bridge/Memory Controller Hardware Specifications
19
Package Description
1.7 Package Description
The following sections provide the package parameters and the mechanical dimensions for the 106.
1.7.1 Package Parameters
The package parameters are as provided in the following list. The package type is a 21 mm x 25 mm,
304-lead C4 ceramic ball grid array (CBGA).
20
Package outline
21 mm x 25 mm
Interconnects
303 (16 x 19 ball array minus one)
Pitch
1.27 mm
Solder attach
63/37 Sn/Pb
Solder balls
10/90 Sn/Pb, 0.89 mm diameter
Maximum module height
3.16 mm
Co-planarity specification
0.15 mm
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Package Description
1.7.2 Mechanical Dimensions
Figure 12 shows the mechanical dimensions for the MPC106.
2X
Top View
–T–
0.200
–F–
B
–E–
0.150 T
A1
P
A
2X
0.200
N
1 2 3 4 5 6 7 8 9 10 1112 13 14 15 16
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
G
Bottom View
*Not to scale
K
MIN
MAX
A
25.0 BASIC
B
21.0 BASIC
C
2.3
3.16
D
0.82
0.93
G
H
1.27 BASIC
0.79
0.99
K
0.635 BASIC
N
5.8
6.0
P
7.2
7.4
Note: All measurements are in mm.
C
303X ∅ D
∅ 0.300 S
T E S
∅ 0.150 S
T
F
S
H
Figure 12. Mechanical Dimensions
MPC106 PCI Bridge/Memory Controller Hardware Specifications
21
System Design Information
1.8 System Design Information
This section provides electrical and thermal design recommendations for successful application of the 106.
1.8.1 PLL Configuration
The 106 requires a single system clock input, SYSCLK. The SYSCLK frequency dictates the frequency of
operation for the PCI bus. An internal PLL on the MPC106 generates a master clock that is used for all of
the internal (core) logic. The master clock provides the core frequency reference and is phase-locked to the
SYSCLK input. The 60x processor, L2 cache, and memory interfaces operate at the core frequency. In the
5:2 clock mode (Rev. 4.0 only), the MPC106 needs to sample the 60x bus clock (on the LBCLAIM
configuration input) to resolve clock phasing with the PCI bus clock (SYSCLK).
The PLL is configured by the PLL[0–3] signals. For a given SYSCLK (PCI bus) frequency, the clock mode
configuration signals (PLL[0–3]) set the core frequency (and the frequency of the VCO controlling the
PLL lock). The supported core and VCO frequencies and the corresponding PLL[0–3] settings are
provided in Table 11.
Table 11. PLL Configuration
Core Frequency (VCO Frequency) in MHz
PLL[0–3]1
Core/SYSCL
K Ratio
VCO
Multiplier
0001
1:1
0100
0101
0110
0111
1000
PCI Bus
16.6 MHz
PCI Bus
20 MHz
PCI Bus
25 MHz
PCI Bus
33.3 MHz
x4
—
—
—
33.3 (133)
2:1
x2
—
—
—
66.6 (133)
2:1
x4
33.3 (133)
40 (160)
50 (200)
—
5:2
2
x2
—
—
—
83.3 (166)
5:2
2
x4
41.6 (166)
—
—
—
x2
—
60(120)
75 (150)
—
3:1
0011
PLL-bypass
1111
Clock off 4
3
PLL off
SYSCLK clocks core circuitry directly
1x core/SYSCLK ratio implied
PLL off
no core clocking occurs
Notes:
PLL[0–3] settings not listed are reserved. Some PLL configurations may select bus, CPU, or VCO frequencies
which are not useful, not supported, or not tested. See Section 1.4.2.1, “Clock AC Specifications,” for valid
SYSCLK and VCO frequencies.
2 5:2 clock modes are only supported by MPC106 Rev 4.0; earlier revisions do not support 5:2 clock modes.
The 5:2 modes require a 60x bus clock applied to the 60x clock phase (LBCLAIM) configuration input signal
during power-on reset, hard reset, and coming out of sleep and suspend power-saving modes.
3 In PLL-bypass mode, the SYSCLK input signal clocks the internal circuitry directly, the PLL is disabled, and
the core/SYSCLK ratio is set for 1:1 mode operation. This mode is intended for factory use and third-party tool
vendors only. Note also: The AC timing specifications given in this document do not apply in PLL-bypass
mode.
4 In clock-off mode, no clocking occurs inside the MPC106 regardless of the SYSCLK input.
5 PLL[0-3] = 0010 (2:1 Core/SYSCLK Ratio; X8 VCO multiplier) exists on the chip but will fail to lock 50% of the
time. Therefore, this configuration should not be used and 1:1 modes between 16-25MHz are not supported.
1
22
MPC106 PCI Bridge/Memory Controller Hardware Specifications
System Design Information
1.8.2 PLL Power Supply Filtering
The AVdd power signal is provided on the 106 to provide power to the clock generation phase-locked loop.
To ensure stability of the internal clock, the power supplied to the AVdd input signal should be filtered
using a circuit similar to the one shown in Figure 13. The circuit should be placed as close as possible to
the AVdd pin to ensure it filters out as much noise as possible.
10 Ω
Vdd
(3.3 V)
AVdd
0.1 µF
10 µF
GND
Figure 13. PLL Power Supply Filter Circuit
1.8.3 Decoupling Recommendations
Due to the 106’s large address and data buses and high operating frequencies, it can generate transient
power surges and high frequency noise in its power supply, especially while driving large capacitive loads.
This noise must be prevented from reaching other components in the system, and the 106 itself requires a
clean, tightly regulated source of power.
It is strongly recommended that the system design include six to eight 0.1 µF (ceramic) and 10 µF
(tantalum) decoupling capacitors to provide both high- and low-frequency filtering. These capacitors
should be placed closely around the perimeter of the 106 package (or on the underside of the PCB). It is
also recommended that these decoupling capacitors receive their power from separate Vdd and GND
power planes in the PCB, utilizing short traces to minimize inductance. Only surface mount technology
(SMT) capacitors should be used to minimize lead inductance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the Vdd plane, to enable quick recharging of the smaller chip capacitors. These bulk capacitors
should have a low equivalent series resistance (ESR) rating to ensure the quick response time necessary.
They should also be connected to the power and ground planes through two vias to minimize inductance.
Suggested bulk capacitors—100 µF (AVX TPS tantalum) or 330 µF (AVX TPS tantalum).
1.8.4 Connection Recommendations
To ensure reliable operation, it is recommended to connect unused inputs to an appropriate signal level.
Unused active low inputs should be tied (using pull-up resistors) to Vdd. Unused active high inputs should
be tied (using pull-down resistors) to GND. All no-connect (NC) signals must remain unconnected.
Power and ground connections must be made to all external Vdd, AVdd, and GND pins of the 106.
1.8.4.1 Pull-up Resistor Recommendations
The MPC106 requires pull-up (or pull-down) resistors on several control signals of the 60x and PCI buses
to maintain the control signals in the negated state after they have been actively negated and released by the
106 or other bus masters. The JTAG test reset signal, TRST, should be pulled down during normal system
operation. Also, as indicated in Table 10, the factory test signal, LSSD_MODE, must be pulled up for
normal device operation
During inactive periods on the bus, the address and transfer attributes on the bus (A[0–31], TT[0–4],
TBST, WT, CI, and GBL) are not driven by any master and may float in the high-impedance state for
relatively long periods of time. Since the MPC106 must continually monitor these signals, this float
MPC106 PCI Bridge/Memory Controller Hardware Specifications
23
System Design Information
condition may cause excessive power draw by the input receivers on the MPC106 or by other receivers in
the system. It is recommended that these signals be pulled up or restored in some manner by the system.
The 60x data bus input receivers on the MPC106 do not require pull-up resistors on the data bus signals
(DH[0–31], DL[0–31], and PAR[0–7]). However, other data bus receivers in the system may require
pull-up resistors on these signals.
In general, the 60x address and control signals are pulled up to 3.3 VDC and the PCI control signals are
pulled up to 5 VDC through weak (2–10 kΩ) resistors. Resistor values may need to be adjusted stronger to
reduce induced noise on specific board designs. Table 12 summarizes the pull-up/pull-down
recommendations for the MPC106.
Table 12. Pull-Up/Pull-Down Recommendations
Signal Type
Signals
60x bus control
BRn
TS, XATS, AACK
ARTRY
TA
Pull up to 3.3 VDC
60x bus
address/transfer
attributes
A[0–31], TT[0–4], TBST
WT, CI, GBL
Pull up to 3.3 VDC
Cache control
ADS
Pull up to 3.3 VDC
HIT, TV
PCI bus control
REQ
FRAME, IRDY
DEVSEL, TRDY, STOP
SERR, PERR
LOCK
FLSHREQ, ISA_MASTER.
JTAG
TRST
Factory test
LSSD_MODE
Pull-Up/Pull-Down
Pull up to 3.3 VDC or pull-down to GND depending on
programmed polarity
Typically pull up to 5 VDC
Note: For closed systems not requiring 5V power,
these may be pulled up to 3.3 VDC.
Pull down to GND (during normal system operation)
Pull up to 3.3 VDC
1.8.5 Thermal Management Information
This section provides thermal management information for the C4/CBGA package. Proper thermal control
design is primarily dependent on the system-level design.
The use of C4 die on a CBGA interconnect technology offers significant reduction in both the signal delay
and the microelectronic packaging volume. Figure 14 shows the salient features of the C4/CBGA
interconnect technology. The C4 interconnection provides both the electrical and the mechanical
connections for the die to the ceramic substrate. After the C4 solder bump is reflowed, epoxy (encapsulant)
is under-filled between the die and the substrate. Under-fill material is commonly used on large high-power
die; however, this is not a requirement of the C4 technology. The package substrate is a multilayer-cofired
ceramic. The package-to-board interconnection is by an array of orthogonal 90/10 (lead/tin) solder balls on
1.27 mm pitch. During assembly of the C4/CBGA package to the board, the high-melt balls do not
collapse.
24
MPC106 PCI Bridge/Memory Controller Hardware Specifications
System Design Information
Chip with C4 Encapsulant
Ceramic Substrate
CBGA Joint
Printed-Circuit Board
Figure 14. Exploded Cross-Sectional View
1.8.5.1 Internal Package Conduction Resistance
For this C4/CBGA packaging technology, the intrinsic conduction thermal resistance paths are as follows:
•
•
The die junction-to-case thermal resistance
The die junction-to-lead thermal resistance
These parameters are shown in Table 13. In this C4/CBGA package, the silicon chip is exposed; therefore,
the package “case” is the top of the silicon.
Table 13. Thermal Resistance
Thermal Metric
Effective Thermal Resistance
Junction-to-case thermal resistance
0.133 °C/W
Junction-to-lead (ball) thermal resistance
3.8 °C/W
Figure 15 provides a simplified thermal network in which a C4/CBGA package is mounted to a
printed-circuit board.
External Resistance
Radiation
Convection
Heat Sink
Thermal Interface Material
Die/Package
Die Junction
Package/Leads
Internal Resistance
Printed-Circuit Board
Radiation
Convection
External Resistance
(Note the internal versus external package resistance)
Figure 15. C4/CBGA Package Mounted to a Printed-Circuit Board
MPC106 PCI Bridge/Memory Controller Hardware Specifications
25
System Design Information
1.8.5.2 Board and System-Level Modeling
A common figure-of-merit used for comparing the thermal performance of various microelectronic
packaging technologies is the junction-to-ambient thermal resistance. The final chip-junction operating
temperature is not only a function of the component-level thermal resistance, but the system-level design
and its operating conditions. In addition to the component’s power consumption, a number of factors affect
the final operating die-junction temperature. For example, these factors might include airflow, board
population, heat sink efficiency, heat sink attach, next-level interconnect technology, and system air
temperature rise.
Due to the complexity and the many variations of system-level boundary conditions for today’s
microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection,
and conduction) may vary widely. For this reason, we recommend using conjugate heat transfer models for
the board as well as system-level designs. To expedite system-level thermal analysis, several “compact”
CBGA thermal models are available on request within FLOTHERM®.
The die junction-to-ambient thermal resistance is shown in Table 14. The model results are in accordance
with SEMI specification G38. This standard specifies a single component be placed on a 7.5 cm x 10 cm
single-layer printed-circuit card. Note that this single metric may not adequately describe
three-dimensional heat flow.
Table 14. Die Junction-to-Ambient Thermal Resistance
26
Airflow Velocity
(Meter/Second)
Airflow Velocity
(Feet/Minute)
Die Junction-to-Ambient Thermal Resistance
(SEMI G38) (°C/W)
1
196.8
22.0
2
393.7
18.5
3
590.0
17.0
MPC106 PCI Bridge/Memory Controller Hardware Specifications
Document Revision History
1.9 Document Revision History
Table 15 lists significant changes between revisions of this document.
Table 15. Document Revision History
Document
Revision
Substantive Change(s)
Rev 0
Initial release
Rev 1
Changed VCO maximum frequency in Table 6 to 200 MHz
Changed input and Hi-Z leakage current in Table 4. from 10µA to 15µA
Changed IOH and IOL in Table 4 from 18mA and 14mA respectively to -7mA and 7mA to correct
the sign and reduce the current to worst case value for the lowest strength default driver
Changed footnote 4 to Table 6 to be consistent with SYSCLK jitter spec of 200ps
Modified Table 7, Figure 3, Table 8, and Figure 5 to clarify reference clock (60x Bus Clock or
SYSCLK) for input and output specifications
Changed Group I and Group II signals input setup requirement for 83 MHz in Table 7 from 3.0 ns
to 3.5 ns min.
Changed Group I-IV (non-PCI signals) input hold requirement (Spec 11a) in Table 7 from 1.0 ns
to 0 ns
Changed Group V and VI (PCI signals) input hold requirement (Spec 11b) in Table 7 from 1.0ns
to -0.5ns
Changed output valid times for all non-PCI signals (Specs 13a, 13b and 14a) from 8 ns to 7 ns at
66 Mhz and from 7 ns to 6 ns at 83 MHz
Corrected Figure 10 to reflect TOE signal is shared with DBG1 on pin U5
Rev 2
Changed input and Hi-Z leakage current, Vin in Table 4 from 5.5V to 3.3V
Changed the power consumption data in Table 5
Changed note 7 of Table 8 to show the minimum timing specification assumes CL=0 pF
Rev 3
Deleted PLL[0-3] = 0010 from Table 11 to remove 1:1 mode operation between 16MHz and
25MHz
Added note 10 to Table 8 regarding PCI hold time
Lowered PCI 3.3V signalling output high voltage from 3.0 V to 2.7V and added current conditions
for PCI 3.3V VOH and VOL in Table 4 to reflect current production test
Included note 12 in Specification 10c of Table 4; Clarified note 9 in Table 8 and included in
Specification 12 and 18; Added a similar “guaranteed by design and not tested” note to Table 9
and included in Specifications 3, 7, and 11. All to reflect current production test.
Corrected Figure 12 dimensions from TBD to actual die size
Table 1 and Table 2 include notes on extended temperature parts.
Rev 4
Table 8, Note 8 changed to include: “These values are guaranteed by design and are not tested.”
Rev 5
Added PNS references below Table 1 and Table 6. Changed footnote ordering in Table 8,
Table 9, and Table 10. Added new footnote 2 to Table 6. Changed part number key.
MPC106 PCI Bridge/Memory Controller Hardware Specifications
27
1.10 Ordering Information
Figure 16 provides the Motorola part-numbering nomenclature for the 106. In addition to the core
frequency, the part numbering scheme also consists of a part modifier and application modifier. The part
modifier indicates any enhancements in the part from the original production design. The application
modifier may specify special bus frequencies or application conditions. Each part number also contains a
revision code. This refers to the die mask revision number and is specified in the part-numbering scheme
for identification purposes only.
pr
MPC
106
A
RX
Product Code Part Identifier Part Modifier Package
RX = BGA
xx
x
x
Frequency
Application Modifier
Revision Level2
66 or 83
C No 5:2 mode
E 3.0
D 5:2 mode
G 4.0
T Extended temperature1
Notes:
See Part Number Specifications (MPC106ARXTGPNS/D).
2 For current revision level, contact local Motorola sales office.
1
Figure 16. Part Number Key
DigitalDNA is a trademark of Motorola, Inc.
The PowerPC name, the PowerPC logotype, and PowerPC 603e are trademarks of International Business Machines Corporation used by Motorola
under license from International Business Machines Corporation.
Information in this document is provided solely to enable system and software implementers to use PowerPC microprocessors. There are no express
or implied copyright licenses granted hereunder to design or fabricate PowerPC integrated circuits or integrated circuits based on the information in
this document.
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee
regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters
which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application
in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola
products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent
regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
HOW TO REACH US:
USA/EUROPE/LOCATIONS NOT LISTED: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or
1-800-441-2447
JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu. Minato-ku, Tokyo 106-8573 Japan. 81-3-3440-3569
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
852-26668334
TECHNICAL INFORMATION CENTER: 1-800-521-6274
HOME PAGE: http://www.motorola.com/semiconductors
DOCUMENT COMMENTS: FAX (512) 933-2625, Attn: RISC Applications Engineering
WORLD WIDE WEB ADDRESSES:
http://www.motorola.com/PowerPC
http://www.motorola.com/NetComm
http://www.motorola.com/ColdFire
MPC106EC/D
Similar pages