ETC2 AP-CF008GE3FR-NDNRJ Value added compact flash series â ¢ specification for industrial cf Datasheet

Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
RoHS Compliant
Value Added Compact Flash Series Ⅲ
Specification for Industrial CF
February 11, 2009
Version 1.2
Apacer Technology Inc.
9/F, No. 100, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Tel: +886-2-2696-1666
Fax: +886-2-2696-1668
www.apacer.com
1
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Features:
Compact Flash Association
Specification Revision 3.0 Standard
Interface
– ATA command set compatible
– ATA mode support for up to:
PIO Mode-6
Multiword DMA Mode-4
Ultra DMA Mode-4
–
Connector Type
50 pins female
–
–
–
Low power consumption (typical)
Supply voltage: 3.3V & 5V
Active mode: 80 mA/95 mA (3.3V/5.0V)
Sleep mode: 700 µA/900 µA (3.3V/5.0V)
–
–
Temperature ranges
– Operation:
Standard: 0°C to 70°C
1
ET : -40°C to 85°C
– Storage: -40°C to 100°C
Flash management
– Intelligent endurance design
Advanced wear-leveling algorithms
S.M.A.R.T. Technology
Built-in Hardware ECC
Enhanced Data Integrity
– Intelligent power failure recovery
RoHS compliant
Performance
Sustained read: up to 35 MB/sec
Sustained write:
Standard: up to 15 MB/sec
High Speed: up to 25 MB/sec
Capacity
Standard:
128, 256, 512 MB
1, 2, 16 GB
– High Speed:
256, 512 MB
1, 2, 4, 8 GB
–
NAND flash type: SLC
1. Extended Temperature
2
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Table of Contents
1. GENERAL DESCRIPTION .................................................................................................... 4
1.1 PERFORMANCE-OPTIMIZED CONTROLLER ............................................................................................................4
1.1.1 Power Management Unit (PMU)..................................................................................................................4
1.1.2 SRAM Buffer .................................................................................................................................................4
2. FUNCTIONAL BLOCK .......................................................................................................... 5
3. PIN ASSIGNMENTS ............................................................................................................... 6
4. CAPACITY SPECIFICATION............................................................................................... 8
4.1 PERFORMANCE SPECIFICATION .............................................................................................................................8
4.2 ENVIRONMENTAL SPECIFICATIONS .......................................................................................................................9
5. FLASH MANAGEMENT ...................................................................................................... 10
5.1 INTELLIGENT ENDURANCE DESIGN.....................................................................................................................10
5.1.1 Advanced wear-leveling algorithms ...........................................................................................................10
5.1.2 S.M.A.R.T. Technology ...............................................................................................................................10
5.1.3 Built-in Hardware ECC ..............................................................................................................................10
5.1.4 Enhanced Data Integrity.............................................................................................................................10
5.2 INTELLIGENT POWER FAILURE RECOVERY .........................................................................................................11
6. SOFTWARE INTERFACE .................................................................................................. 12
6.1 COMMAND SET ...................................................................................................................................................12
7. ELECTRICAL SPECIFICATION ...................................................................................... 14
8. PHYSICAL CHARACTERISTICS ..................................................................................... 15
8.1 DIMENSION .........................................................................................................................................................15
9. PRODUCT ORDERING INFORMATION ........................................................................ 16
9.1 PRODUCT CODE DESIGNATIONS .........................................................................................................................16
9.2 VALID COMBINATIONS .......................................................................................................................................17
3
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
1. General Description
Apacer’s Industrial Compact Flash Card (CFC) offers the most reliable and high performance storage
which is compatible with CF Type I and Type II devise. Unlike the ordinary consumer Compact Flash
cards, Apacer Industrial Compact Flash card provides solid traceability to ensure all products HW/SW are
the same as you qualified.
Apacer’s CFC provides complete PCMCIA - ATA functionality and compatibility. Apacer ‘s Compact Flash
technology is designed for use in Point of Sale (POS) terminals, telecom, IP-STB, medical instruments,
surveillance systems, industrial PCs and handheld applications.
Featuring technologies as Advanced Wear-leveling algorithms, S.M.A.R.T, Enhanced Data Integrity, Builtin Hardware ECC, and Intelligent Power Failure Recovery, Apacer’s Industrial Compact Flash Card
assures users of a versatile device on data storage.
1.1 Performance-Optimized Controller
The Compact Flash Card Controller translates standard CF signals into flash media data and control
signals.
1.1.1 Power Management Unit (PMU)
The power management unit (PMU) controls the power consumption of the Compact Flash card controller.
It reduces the power consumption of the Compact Flash Card Controller by putting circuitry not in
operation into sleep mode. The PMU has zero wake-up latency.
1.1.2 SRAM Buffer
The Compact Flash Card Controller performs as an SRAM buffer to optimize the host’s data transfer to
and from the flash media.
4
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
2. Functional Block
The Compact Flash Card (CFC) includes a controller and flash media, as well as the Compact Flash
standard interface. Figure 2-1 shows the functional block diagram.
Flash Array
Flash
Media
Compact Flash
Interface
Flash
Media
Compact Flash
Controller
Flash
Media
Flash
Media
Figure 2-1: Functional block diagram
5
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
3. Pin Assignments
Table 3-1 lists the pin assignments with respective signal names for the 50-pin configuration. A “#” suffix
indicates the active low signal. The pin type can be input, output or input/output.
Table 3-1: Pin assignments (1 of 2)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Memory card mode
Signal name
GND
D3
D4
D5
D6
D7
#CE1
A10
#OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
WP
#CD2
#CD1
D11
D12
D13
D14
D15
#CE2
#VS1
#IORD
#IOWR
#WE
RDY/-BSY
VCC
#CSEL
#VS2
RESET
Pin I/O type
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
I
I
I
I
I/O
I/O
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I
O
I
I
I
O
I
O
I
I/O card mode
Signal name
GND
D3
D4
D5
D6
D7
#CE1
A10
#OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
#IOCS16
#CD2
#CD1
D11
D12
D13
D14
D15
#CE2
#VS1
#IORD
#IOWR
#WE
-IREQ
VCC
#CSEL
#VS2
RESET
Pin I/O type
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
I
I
I
I
I/O
I/O
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I
O
I
I
I
O
I
O
I
True IDE mode
Signal name
GND
D3
D4
D5
D6
D7
#CE1
1
A10
#OE
1
A9
1
A8
1
A7
VCC
1
A6
1
A5
1
A4
1
A3
A2
A1
A0
D0
D1
D2
#IOCS16
#CD2
#CD1
D11
D12
D13
D14
D15
#CE2
#VS1
#IORD
#IOWR
#WE
INTRQ
VCC
#CSEL
#VS2
RESET
Pin I/O type
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
I
I
I
I
I/O
I/O
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I
O
I
I
I
O
I
O
I
6
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Table 3-1: Pin assignments (2 of 2)
Pin No.
1.
2.
Memory card mode
Signal name Pin I/O type
42
#WAIT
O
43
#INPACK
O
44
-REG
I
45
BVD2
O
46
BVD1
O
47
D8
I/O
48
D9
I/O
49
D10
I/O
50
GND
The signal should be tied to VCC by the host.
I/O card mode
Signal name
#WAIT
#INPACK
#REG
#SPKR
#STSCHG
D8
D9
D10
GND
Pin I/O type
O
O
I
O
O
I/O
I/O
I/O
-
True IDE mode
Signal name
IORDY
2
DMARQ
2
DMACK
#DASP
#PDIAG
D8
D9
D10
GND
Pin I/O type
O
O
I
O
O
I/O
I/O
I/O
-
Connection required when UDMA is in use.
7
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
4. Capacity Specification
Capacity specification of the Compact Flash Card series (CFC) is available as shown in Table 4-1. It lists
the specific capacity and the default numbers of heads, sectors and cylinders for each product line.
Table 4-1: Capacity specifications
Capacity
Total bytes
Cylinders
Heads
Sectors
Max LBA
128 MB
127,641,600
980
8
32
250,880
256 MB
256,352,256
980
16
32
501,760
512 MB
511,664,128
993
16
63
1,000,944
1GB
1,024,655,360
1,986
16
63
2,001,888
2GB
2,048,589,824
3,970
16
63
4,001,760
4GB
4,100,059,136
7,964
16
63
8,027,712
8GB
8,176,340,992
15,880
16
63
16,007,040
16GB
16,368,721,920
16,383*
16
63
32,014,080
1. Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies
4.1 Performance Specification
Performances of the Standard and High Speed ATA-Flash Disk are listed in Table 4-2 and Table 4-3.
Table 4-2: Standard Performance specifications
Capacity
128 MB / 256 MB
512 MB / 1 GB
2 GB
16 GB
Sustained read (MB/s)
18
30
35
22
Sustained write (MB/s)
7
12
15
15
Performance
Table 4-3: High Speed Performance specifications
Capacity
256 MB / 512 MB
1GB / 2 GB / 4 GB / 8 GB
Sustained read (MB/s)
30
35
Sustained write (MB/s)
13
22~25
Performance
8
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
4.2 Environmental Specifications
Environmental specification of the Compact Flash Card series (CFC) which follows the MIL-STD-810F
standards is available as shown in Table 4-4.
Table 4-4: Environmental specifications
Environment
Temperature
Specification
Operation
0°C to 70°C; -40°C to 85°C (ET
Storage
-40°C to 100°C
Humidity
Vibration (Non-Operation)
Shock (Non-Operation)
1
)
5% to 95% RH (Non-condensing)
Sine wave: 10~2000Hz, 15G (X, Y, Z axes)
Half sine wave, Peak acceleration 50 G, 11 ms (X, Y, Z ; All 6 axes)
1. Extended Temperature
9
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
5. Flash Management
5.1 Intelligent Endurance Design
5.1.1 Advanced wear-leveling algorithms
The NAND flash devices are limited by a certain number of write cycles. When using a file system,
frequent file table updates is mandatory. If some area on the flash wears out faster than others, it would
significantly reduce the lifetime of the whole device, even if the erase counts of others are far from the
write cycle limit. Thus, if the write cycles can be distributed evenly across the media, the lifetime of the
media can be prolonged significantly. The scheme is achieved both via buffer management and Apacerspecific advanced wear leveling to ensure that the lifetime of the flash media can be increased, and the
disk access performance is optimized as well.
5.1.2 S.M.A.R.T. technology
S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard
allowing disk drives to automatically monitor their own health and report potential problems. It protects the
user from unscheduled downtime by monitoring and storing critical drive performance and calibration
parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure. Apacer
SMART feature adopts the standard SMART command B0h to read data from the drive. When the Apacer
SMART Utility running on the host, it analyzes and reports the disk status to the host before the device is
in critical condition.
5.1.3 Built-in hardware ECC
The ATA-Disk Module uses BCH Error Detection Code (EDC) and Error Correction Code (ECC)
algorithms which correct up to eight random single-bit errors for each 512-byte block of data. High
performance is fulfilled through hardware-based error detection and correction.
5.1.4 Enhanced data integrity
The properties of NAND flash memory make it ideal for applications that require high integrity while
operating in challenging environments. The integrity of data to NAND flash memory is generally
maintained through ECC algorithms and bad block management. Flash controllers can support up to 8
bits ECC capability for accuracy of data transactions, and bad block management is a preventive
mechanism from loss of data by retiring unusable media blocks and relocating the data to the other blocks,
along with the integration of advanced wear leveling algorithms, so that the lifespan of device can be
expanded.
10
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
5.2 Intelligent Power Failure Recovery
The Low Power Detection on the controller initiates cached data saving before the power supply to the
device is too low. This feature prevents the device from crash and ensures data integrity during an
unexpected blackout. Once power was failure before cached data writing back into flash, data in the
cache will lost. The next time the power is on, the controller will check these fragmented data segment,
and, if necessary, replace them with old data kept in flash until programmed successfully.
11
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
6. Software Interface
6.1 Command Set
Table 6-1 summarizes the command set with the paragraphs that follow describing the individual
commands and the task file for each.
Table 6-1: Command set (1 of 2)
Command
1
2
3
4
5
FR
SC
SN
CY
E5H or 98H
-
-
-
-
D
8
-
Execute-Drive-Diagnostic
90H
-
-
-
-
D
-
Erase Sector(s)
C0H
-
Y
Y
Y
Y
Y
Flush-Cache
E7H
-
-
-
-
D
-
8
Check-Power-Mode
7
DH
6
Code
LBA
Format Track
50H
-
Y
-
Y
Y
Y
Identify-Drive
ECH
-
-
-
-
D
-
Idle
E3H or 97H
-
Y
-
-
D
-
Idle-Immediate
E1H or 95H
-
-
-
-
D
-
Initialize-Drive-Parameters
91H
-
Y
-
-
Y
-
NOP
00H
-
-
-
-
D
-
Read-Buffer
E4H
-
-
-
-
D
-
Read-DMA
C8H or C9H
-
Y
Y
Y
Y
Y
C4H
-
Y
Y
Y
Y
Y
Read-Sector(s)
20H or 21H
-
Y
Y
Y
Y
Y
Read-Verify-Sector(s)
40H or 41H
-
Y
Y
Y
Y
Y
Recalibrate
1XH
-
-
-
-
D
-
Request-Sense
03H
-
-
-
-
D
-
Seek
7XH
-
-
Y
Y
Y
Y
-
-
-
D
-
Read-Multiple
Set-Features
7
Y
EFH
12
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Table 6-1: Command set (2 of 2)
Command
1
2
3
4
5
FR
SC
SN
CY
SMART
B0H
Y
Y
Y
Y
D
Set-Multiple-Mode
C6H
-
Y
-
-
D
-
Set-Sleep-Mode
E6H or 99H
-
-
-
-
D
-
Standby
E2H or 96H
-
-
-
-
D
-
Standby-lmmediate
E0H or 94H
-
-
-
-
D
-
Translate-Sector
87H
-
Y
Y
Y
Y
Y
Write-Buffer
E8H
-
-
-
-
D
-
Write-DMA
CAH or CBH
-
Y
Y
Y
Y
Y
Write-Multiple
C5H
-
Y
Y
Y
Y
Y
Write-Multiple-Without-Erase
CDH
-
Y
Y
Y
Y
Y
30H or 31H
-
Y
Y
Y
Y
Y
Write-Sector-Without-Erase
38H
-
Y
Y
Y
Y
Y
Write-Verify
3CH
-
Y
Y
Y
Y
Y
Write-Sector(s)
DH
6
Code
LBA
1. FR - Features register
2. SC - Sector Count register
3. SN - Sector Number register
4. CY - Cylinder registers
5. DH - Drive/Head register
6. LBA - Logical Block Address mode supported (see command descriptions for use)
7. Y - The register contains a valid parameter for this command
8. For the Drive/Head register:
Y means both the CFC and Head parameters are used
D means only the CFC parameter is valid and not the Head parameter
13
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
7. Electrical Specification
Caution: Absolute Maximum Stress Ratings – Applied conditions greater than those listed under
“Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these conditions or conditions greater than those defined in
the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating
conditions may affect device reliability.
Table 7-1: Operating range
Range
Ambient Temperature
3.3V
5V
Standard
Extended Temperature
0°C to +70°C
-40°C to +85°C
3.135-3.465V
4.75-5.25V
Table 7-2: Absolute maximum power pin stress ratings
Parameter
Symbol
Input Power
Voltage on any pin except VDD with respect to GND
VDD
V
Conditions
-0.3V min. to 6.5V max.
-0.5V min. to VDD + 0.5V max.
Table 7-3: Recommended system power-up timing
Symbol
Parameter
1
TPU-READY
1
TPU-WRITE
Power-up to Ready Operation
Power-up to Write Operation
Typical
Maximum
Units
200
200
1000
1000
ms
ms
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
14
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
8. Physical Characteristics
8.1 Dimension
TABLE 8-1: Type I CFC physical specification
Length:
Width:
Thickness (Including Label Area):
36.40 +/- 0.15mm (1.433+/- 0.06 in.)
42.80 +/- 0.10mm (1.685+/- 0.04 in.)
3.3mm+/-0.10mm (0.130+/-0.04in.)
Unit: mm
FIGURE 8-1: Physical dimension
15
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
9. Product Ordering Information
9.1 Product Code Designations
A P – C F x x x x E 3 X R – XXXXJ
Specification
NR: Non-Removable Setting
NDNR: Non-DMA + Non-Removable
ETNR: Ext. Temp. + Non-Removable
ETNDNR: Ext. Temp + Non-DMA + Non-Removable
J: Value Added Ⅰ
RoHS Compliant
Configuration
E: Standard
F: High Speed
Controller Type
CFC Type
Capacity:
128M:
256M:
512M:
001G:
002G:
004G:
008G:
016G:
128MB
256MB
512MB
1GB
2GB
4GB
8GB
16GB
Model Name
Apacer Product Code
16
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
9.2 Valid Combinations
Standard Temperature
Non-Removable
Standard
Capacity
High Speed
P/N
Capacity
P/N
128MB
AP-CF128ME3ER-NRJ
256MB
AP-CF256ME3FR-NRJ
256MB
AP-CF256ME3ER-NRJ
512MB
AP-CF512ME3FR-NRJ
512MB
AP-CF512ME3ER-NRJ
1GB
AP-CF001GE3FR-NRJ
1GB
AP-CF001GE3ER-NRJ
2GB
AP-CF001GE3FR-NRJ
2GB
AP-CF002GE3ER-NRJ
4GB
AP-CF004GE3FR-NRJ
16GB
AP-CF016GE3ER-NRJ
8GB
AP-CF008GE3FR-NRJ
Non-DMA & Non-Removable
Standard
Capacity
P/N
High Speed
Capacity
P/N
128MB
AP-CF128ME3ER-NDNRJ
256MB
AP-CF256ME3FR-NDNRJ
256MB
AP-CF256ME3ER-NDNRJ
512MB
AP-CF512ME3FR-NDNRJ
512MB
AP-CF512ME3ER-NDNRJ
1GB
AP-CF001GE3FR-NDNRJ
1GB
AP-CF001GE3ER-NDNRJ
2GB
AP-CF001GE3FR-NDNRJ
2GB
AP-CF002GE3ER-NDNRJ
4GB
AP-CF004GE3FR-NDNRJ
16GB
AP-CF016GE3ER-NDNRJ
8GB
AP-CF008GE3FR-NDNRJ
17
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Extended Temperature
Non-Removable
Standard
Capacity
High Speed
P/N
Capacity
P/N
128MB
AP-CF128ME3ER-ETNRJ
256MB
AP-CF256ME3FR-ETNRJ
256MB
AP-CF256ME3ER-ETNRJ
512MB
AP-CF512ME3FR-ETNRJ
512MB
AP-CF512ME3ER-ETNRJ
1GB
AP-CF001GE3FR-ETNRJ
1GB
AP-CF001GE3ER-ETNRJ
2GB
AP-CF001GE3FR-ETNRJ
2GB
AP-CF002GE3ER-ETNRJ
4GB
AP-CF004GE3FR-ETNRJ
16GB
AP-CF016GE3ER-ETNRJ
8GB
AP-CF008GE3FR-ETNRJ
Non-DMA & Non-Removable
Standard
High Speed
Capacity
P/N
Capacity
P/N
128MB
AP-CF128ME3ER-ETNDNRJ
256MB
AP-CF256ME3FR-ETNDNRJ
256MB
AP-CF256ME3ER-ETNDNRJ
512MB
AP-CF512ME3FR-ETNDNRJ
512MB
AP-CF512ME3ER-ETNDNRJ
1GB
AP-CF001GE3FR-ETNDNRJ
1GB
AP-CF001GE3ER-ETNDNRJ
2GB
AP-CF001GE3FR-ETNDNRJ
2GB
AP-CF002GE3ER-ETNDNRJ
4GB
AP-CF004GE3FR-ETNDNRJ
16GB
AP-CF016GE3ER-ETNDNRJ
8GB
AP-CF008GE3FR-ETNDNRJ
18
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Revision History
Revision
Date
Description
Remark
1.0
12/30/2008
Official release
1.1
01/08/2009
Context revised
1.2
02/11/2009
Modified document layout
19
© 2009 Apacer Technology Inc.
Rev. 1.2
Value Added Compact Flash Ⅲ series
AP-CFxxxxE3XR-XXXXJ
Global Presence
Taiwan (Headquarters)
Apacer Technology Inc.
9F, 100, Sec. 1, Hsin Tai Wu Rd.,
Hsichih, 221 Taipei Hsien
Taiwan, R.O.C.
Tel: +886-2-2696-1666
Fax: +886-2-2696-1668
[email protected]
U.S.A.
Apacer Memory America, Inc.
386 Fairview Way, Suite102,
Milpitas, CA 95035
Tel: 1-408-586-1291
Fax: 1-408-935-9611
[email protected]
Japan
Apacer Technology Corp.
5F, Matsura Bldg., Shiba, Minato-Ku
Tokyo, 105-0014, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018
[email protected]
Europe
Apacer Technology B.V.
Europalaan 89
5232 BC 'S-Hertogenbosch
The Netherlands
Tel: 31-73-645-9620
Fax: 31-73-645-9629
[email protected]
China
Apacer Electronic (Shanghai) Co., Ltd
1301, No.251,Xiaomuqiao Road, Shanghai,
200032, China
Tel: 86-21-5529-0222
Fax: 86-21-5206-6939
[email protected]
India
Apacer Technologies Pvt. Ltd.
#143, 1st Floor, Raheja Arcade,
5th Block Kormangala Industrial Layout,
Bangalore - 560095, India
Tel: 91-80-4152-9061
[email protected]
20
© 2009 Apacer Technology Inc.
Rev. 1.2
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apacer:
AP-CF256ME3FR-ETNDNRK AP-CF256ME3FR-ETNRK
Similar pages