TI ISO7831F Iso7831 high-performance, 8000 vpk reinforced triple digital isolator Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
ISO7831 High-Performance, 8000 VPK Reinforced Triple Digital Isolators
1 Features
3 Description
•
•
•
•
•
The ISO7831 is a high-performance, 3 -channel
digital isolator with 8000 VPK isolation voltage. This
device has reinforced isolation certifications
according to VDE, CSA, and CQC. The isolator
provides high electromagnetic immunity and low
emissions at low power consumption, while isolating
CMOS or LVCMOS digital I/Os. Each isolation
channel has a logic input and output buffer separated
by silicon dioxide (SiO2) insulation barrier. This device
comes with enable pins which can be used to put the
respective outputs in high impedance for multi-master
driving applications and to reduce power
consumption. ISO7831 has two forward and one
reverse-direction channels . If the input power or
signal is lost, default output is 'high' for the ISO7831
and 'low' for the ISO7831F device. See Device
Functional Modes for further details. Used in
conjunction with isolated power supplies, this device
prevents noise currents on a data bus or other
circuits from entering the local ground and interfering
with or damaging sensitive circuitry. Through
innovative chip design and layout techniques,
electromagnetic compatibility of ISO7831 has been
significantly enhanced to ease system-level ESD,
EFT, Surge and Emissions compliance. ISO7831 is
available in 16-pin SOIC wide-body (DW) package.
1
•
•
•
•
•
•
•
•
Signaling Rate: Up to 100 Mbps
Wide Supply Range: 2.25 V to 5.5 V
2.25 V to 5.5 V Level Translation
Wide Temperature Range: –55°C to 125°C
Low Power Consumption, Typical 2.5 mA per
Channel at 1 Mbps
Low Propagation Delay: 11 ns Typical
(5 V Supplies)
Industry leading CMTI: ±100 kV/μs
Robust Electromagnetic Compatibility (EMC)
System-Level ESD, EFT, and Surge Immunity
Low Emissions
Isolation Barrier Life: >25 Years
Wide Body SOIC-16 Package
Safety and Regulatory Approvals:
– 8000 VPK VIOTM and 2121 VPK VIORM
Reinforced Isolation per DIN V VDE V 0884-10
(VDE V 0884-10):2006-12
– 5.7 kVRMS Isolation for 1 Minute per UL 1577
– CSA Component Acceptance Notice 5A, IEC
60950-1, IEC 60601-1 and IEC 61010-1 End
Equipment Standards
– CQC Certification per GB4943.1-2011
PART NUMBER
ISO7831
ISO7831F
2 Applications
•
•
•
•
•
•
Device Information(1)
Industrial Automation
Motor Control
Power Supplies
Solar Inverters
Medical Equipment
Hybrid Electric Vehicles
PACKAGE
SOIC, DW (16)
BODY SIZE (NOM)
10.30 mm x 7.50 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
VCCI
Isolation
Capacitor
VCCO
INx
OUTx
ENx
GNDI
GNDO
(1)
VCCI and GNDI are supply and ground connections respectively for the input channels.
(2)
VCCO and GNDO are supply and ground connections respectively for the output channels.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
7
8
1
1
1
2
3
4
Absolute Maximum Ratings ...................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 5
Power Rating............................................................. 5
Electrical Characteristics, 5 V ................................... 6
Electrical Characteristics, 3.3 V ................................ 7
Electrical Characteristics, 2.5 V ................................ 8
Switching Characteristics, 5 V .................................. 9
Switching Characteristics, 3.3 V ............................. 9
Switching Characteristics, 2.5 V ........................... 10
Typical Characteristics .......................................... 11
Parameter Measurement Information ................ 12
Detailed Description ............................................ 14
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
14
14
15
19
Application and Implementation ........................ 20
9.1 Application Information............................................ 20
9.2 Typical Application .................................................. 20
10 Power Supply Recommendations ..................... 22
11 Layout................................................................... 23
11.1 Layout Guidelines ................................................. 23
11.2 Layout Example .................................................... 23
12 Device and Documentation Support ................. 24
12.1
12.2
12.3
12.4
12.5
12.6
Documentation Support ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
24
24
24
24
24
13 Mechanical, Packaging, and Orderable
Information ........................................................... 24
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (July 2015) to Revision A
•
2
Page
Changed From: 1-page Product Preview To: Production datasheet...................................................................................... 1
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
5 Pin Configuration and Functions
DW Package
16-Pin SOIC
Top View
1
16
VCC2
GND1
2
15
GND2
INA
3
14
OUTA
INB
4
13
OUTB
OUTC
5
12
INC
NC
6
11
NC
EN1
7
10
EN2
GND1
8
9
I S O L A TI O N
VCC1
GND2
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
EN1
7
I
Output enable 1. Output pins on side 1 are enabled when EN1 is high or open and in highimpedance state when EN1 is low.
EN2
10
I
Output enable 2. Output pins on side 2 are enabled when EN2 is high or open and in highimpedance state when EN2 is low.
GND1
2, 8
—
Ground connection for VCC1
GND2
9, 15
—
Ground connection for VCC2
3
I
Input, channel A
INB
4
I
Input, channel B
INC
12
I
Input, channel C
OUTA
14
O
Output, channel A
OUTB
13
O
Output, channel B
OUTC
5
O
Output, channel C
6,11
—
Not connected
VCC1
1
—
Power supply, VCC1
VCC2
16
—
Power supply, VCC2
INA
NC
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
3
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
See
(1)
VCC1,
VCC2
Supply voltage (2)
MIN
MAX
UNIT
–0.5
6
V
–0.5
VCCX + 0.5 (3)
V
INx
Voltage
OUTx
ENx
IO
Output current
–15
15
mA
Tstg
Storage temperature
–65
150
°C
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values except differential I/O bus voltages are with respect to the local ground terminal (GND1 or GND2) and are peak
voltage values.
Maximum voltage must not exceed 6 V
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1)
±6000
Charged device model (CDM), per JEDEC specification JESD22-C101, all
pins (2)
±1500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
VCC1,
VCC2
IOH
IOL
Supply voltage
High-level output current
Low-level output current
NOM
2.25
VCCO (1) = 5 V
–4
VCCO (1) = 3.3 V
–2
VCCO (1) = 2.5 V
–1
MAX
5.5
V
mA
VCCO (1) = 5 V
4
VCCO (1) = 3.3 V
2
VCCO (1) = 2.5 V
1
(1)
(1)
High-level input voltage
VIL
Low-level input voltage
0
0.3 × VCCI (1)
DR
Signaling rate
0
100
Mbps
TJ
Junction temperature (2)
–55
150
°C
TA
Ambient temperature
–55
125
°C
4
VCCI
mA
VIH
(1)
(2)
0.7 × VCCI
UNIT
25
V
V
VCCI = Input-side VCC; VCCO = Output-side VCC.
To maintain the recommended operating conditions for TJ, see Thermal Information.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
6.4 Thermal Information
DW (SOIC)
THERMAL METRIC (1)
16 Pins
RθJA
Junction-to-ambient thermal resistance
78.9
RθJC(top)
Junction-to-case(top) thermal resistance
41.6
RθJB
Junction-to-board thermal resistance
43.6
ψJT
Junction-to-top characterization parameter
15.5
ψJB
Junction-to-board characterization parameter
43.1
RθJC(bottom)
Junction-to-case(bottom) thermal resistance
N/A
(1)
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.5 Power Rating
VALUE
PD
Maximum power dissipation by ISO7831
PD1
Maximum power dissipation by side-1 of ISO7831
PD2
Maximum power dissipation by side-2 of ISO7831
VCC1 = VCC2 = 5.5 V, TJ = 150°C,
CL = 15 pF, input a 50 MHz 50% duty cycle
square wave
UNIT
150
50
100
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
mW
5
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
6.6 Electrical Characteristics, 5 V
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
(1)
(1)
VOH
High-level output voltage
IOH = –4 mA; see Figure 7
VOL
Low-level output voltage
IOL = 4 mA; see Figure 7
VCCO
VI(HYS)
Input threshold voltage
hysteresis
IIH
High-level input current
VIH = VCCI (1) at INx or ENx
IIL
Low-level input current
VIL = 0 V at INx or ENx
–10
CMTI
Common-mode transient
immunity
VI = VCCI (1) or 0 V; see Figure 10
70
– 0.4
VCCO
0.4
(1)
10
100
kV/μs
DC signal: VI = 0 V
(Devices with suffix F) ,
VI = VCCI (Devices
without suffix F)
1.0
1.6
ICC2
Disable;
EN1 = EN2 = 0 V
DC signal: VI = 0 V
(Devices with suffix F) ,
VI = VCCI (Devices
without suffix F)
0.8
1.3
ICC1
Disable;
EN1 = EN2 = 0 V
DC signal: VI = VCCI
(Devices with suffix F) ,
VI = 0 V(Devices without
suffix F)
3.3
4.8
ICC2
Disable;
EN1 = EN2 = 0 V
DC signal: VI = VCCI
(Devices with suffix F) ,
VI = 0 V(Devices without
suffix F)
2
2.9
ICC1
DC signal
DC signal: VI = 0 V
(Devices with suffix F) ,
VI = VCCI (Devices
without suffix F)
1.4
2.3
ICC2
DC signal
DC signal: VI = 0 V
(Devices with suffix F) ,
VI = VCCI (Devices
without suffix F)
1.7
2.6
ICC1
DC signal
DC signal: VI = VCCI
(Devices with suffix F) ,
VI = 0 V(Devices without
suffix F)
3.8
5.6
ICC2
DC signal
DC signal: VI = VCCI
(Devices with suffix F) ,
VI = 0 V(Devices without
suffix F)
3
4.3
ICC1
1 Mbps
2.6
4
ICC2
1 Mbps
2.4
3.6
ICC1
10 Mbps
3.2
4.5
ICC2
10 Mbps
ICC1
100 Mbps
ICC2
100 Mbps
(1)
6
μA
μA
Disable;
EN1 = EN2 = 0 V
AC signal: All channels
switching with square
wave clock input;
CL = 15 pF
V
V
ICC1
Supply current
UNIT
V
– 0.2
0.2
0.1 × VCCO
MAX
mA
3.4
4.6
8.7
10.5
13.2
15.8
VCCI = Input-side VCC; VCCO = Output-side VCC.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
6.7 Electrical Characteristics, 3.3 V
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
(1)
(1)
VOH
High-level output voltage
IOH = –2 mA; see Figure 7
VOL
Low-level output voltage
IOL = 2 mA; see Figure 7
VCCO
VI(HYS)
Input threshold voltage
hysteresis
IIH
High-level input current
VIH = VCCI (1) at INx or ENx
IIL
Low-level input current
VIL = 0 V at INx or ENx
-10
CMTI
Common-mode transient
immunity
VI = VCCI (1) or 0 V; see Figure 10
70
– 0.4
VCCO
V
0.4
V
μA
100
kV/μs
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
1.0
1.6
ICC2
Disable;
EN1 = EN2 = 0 V
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
0.8
1.3
ICC1
Disable;
EN1 = EN2 = 0 V
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
3.3
4.8
ICC2
Disable;
EN1 = EN2 = 0 V
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
1.9
2.9
ICC1
DC signal
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
1.4
2.3
ICC2
DC signal
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
1.7
2.6
ICC1
DC signal
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
3.8
5.6
ICC2
DC signal
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
2.9
4.3
ICC1
1 Mbps
2.6
4
ICC2
1 Mbps
2.4
3.5
ICC1
10 Mbps
3.0
4.3
ICC2
10 Mbps
3.1
4.3
ICC1
100 Mbps
6.9
8.3
ICC2
100 Mbps
10.1
12.2
(1)
μA
10
Disable;
EN1 = EN2 = 0 V
AC signal: All channels
switching with square
wave clock input;
CL = 15 pF
V
(1)
ICC1
Supply current
UNIT
– 0.2
0.2
0.1 × VCCO
MAX
mA
VCCI = Input-side VCC; VCCO = Output-side VCC.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
7
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
6.8 Electrical Characteristics, 2.5 V
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
VCCO (1) – 0.4
VOH
High-level output voltage
IOH = –1 mA; see Figure 7
VOL
Low-level output voltage
IOL = 1 mA; see Figure 7
VI(HYS)
Input threshold voltage
hysteresis
IIH
High-level input current
VIH = VCCI (1) at INx or ENx
IIL
Low-level input current
VIL = 0 V at INx or ENx
–10
CMTI
Common-mode transient
immunity
VI = VCCI (1) or 0 V; see Figure 10
70
TYP
MAX
VCCO –
0.2
0.2
V
0.4
0.1 × VCCO (1)
10
100
kV/μs
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
0.9
1.6
ICC2
Disable;
EN1 = EN2 = 0 V
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
0.8
1.3
ICC1
Disable;
EN1 = EN2 = 0 V
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
3.3
4.8
ICC2
Disable;
EN1 = EN2 = 0 V
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
1.9
2.9
DC signal
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
1.4
2.3
DC signal
DC signal: VI = 0 V
(Devices with suffix F) , VI
= VCCI (Devices without
suffix F)
1.7
2.6
DC signal
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
3.8
5.6
ICC2
DC signal
DC signal: VI = VCCI
(Devices with suffix F) , VI
= 0 V(Devices without
suffix F)
2.9
4.3
ICC1
1 Mbps
2.6
4
ICC2
1 Mbps
2.3
3.5
ICC1
10 Mbps
2.9
4.3
ICC2
10 Mbps
2.9
4.1
ICC1
100 Mbps
ICC2
100 Mbps
ICC2
ICC1
(1)
8
AC signal: All channels
switching with square
wave clock input;
CL = 15 pF
μA
μA
Disable;
EN1 = EN2 = 0 V
Supply current
V
V
ICC1
ICC1
UNIT
(1)
mA
5.8
7.2
8.2
10.0
VCCI = Input-side VCC; VCCO = Output-side VCC.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
6.9 Switching Characteristics, 5 V
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD (1)
Pulse width distortion |tPHL – tPLH|
tsk(o)
(2)
tsk(pp)
(3)
TEST CONDITIONS
See Figure 7
Channel-to-channel output skew time
Output signal fall time
tPHZ
Disable propagation delay, high-to-high impedance output
tPLZ
(1)
(2)
(3)
0.55
4.1
UNIT
2.5
ns
1.7
3.9
1.9
3.9
12
20
Disable propagation delay, low-to-high impedance output
12
20
Enable propagation delay, high impedance-to-high output
10
20
ns
2
2.5
μs
Enable propagation delay, high impedance-to-low output
2
2.5
μs
Enable propagation delay, high impedance-to-low output
10
20
ns
0.2
9
μs
See Figure 7
See Figure 8
Enable propagation delay, high impedance-to-high output
Measured from the time VCC
goes below 1.7 V. See Figure 9
Default output delay time from input power loss
tie
16
4.5
tf
tfs
MAX
11
Part-to-part skew time
Output signal rise time
tPZL
TYP
6
Same-direction channels
tr
tPZH
MIN
16
Time interval error
2
0.90
– 1 PRBS data at 100 Mbps
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
6.10 Switching Characteristics, 3.3 V
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD (1)
Pulse width distortion |tPHL – tPLH|
tsk(o)
(2)
tsk(pp)
(3)
tf
Output signal fall time
tPHZ
tPLZ
tfs
tie
(1)
(2)
(3)
MIN
TYP
MAX
6
10.8
16
0.7
4.2
Same-direction channels
UNIT
2.2
Part-to-part skew time
Output signal rise time
tPZL
See Figure 7
Channel-to-channel output skew time
tr
tPZH
TEST CONDITIONS
4.5
0.8
3
0.8
3
Disable propagation delay, high-to-high impedance
output
17
32
Disable propagation delay, low-to-high impedance
output
17
32
17
32
ns
2
2.5
μs
Enable propagation delay, high impedance-to-low
output
2
2.5
μs
Enable propagation delay, high impedance-to-low
output
17
32
ns
0.2
9
μs
See Figure 7
Enable propagation delay, high impedance-to-high
output
Enable propagation delay, high impedance-to-high
output
Default output delay time from input power loss
Time interval error
ns
See Figure 8
Measured from the time VCC goes
below 1.7 V. See Figure 9
16
2
– 1 PRBS data at 100 Mbps
0.91
ns
Also known as Pulse Skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
9
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
6.11 Switching Characteristics, 2.5 V
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD (1)
Pulse width distortion |tPHL – tPLH|
tsk(o)
(2)
tsk(pp)
(3)
tf
Output signal fall time
tPHZ
tPLZ
tfs
tie
(1)
(2)
(3)
10
MIN
TYP
MAX
7.5
11.7
17.5
0.66
4.2
Same-direction Channels
UNIT
2.2
Part-to-part skew time
Output signal rise time
tPZL
See Figure 7
Channel-to-channel output skew time
tr
tPZH
TEST CONDITIONS
4.5
1
3.5
1.2
3.5
Disable propagation delay, high-to-high impedance
output
22
45
Disable propagation delay, low-to-high impedance
output
22
45
18
45
ns
2
2.5
μs
Enable propagation delay, high impedance-to-low
output
2
2.5
μs
Enable propagation delay, high impedance-to-low
output
18
45
ns
0.2
9
μs
See Figure 7
Enable propagation delay, high impedance-to-high
output
Enable propagation delay, high impedance-to-high
output
Default output delay time from input power loss
Time interval error
ns
See Figure 8
Measured from the time VCC goes
below 1.7 V. See Figure 9
16
2
– 1 PRBS data at 100 Mbps
0.91
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
6.12 Typical Characteristics
24
10
ICC1 at 2.5 V (mA)
ICC2 at 2.5 V (mA)
ICC1 at 3.3 V (mA)
ICC2 at 3.3 V (mA)
ICC1 at 5 V (mA)
ICC2 at 5 V (mA)
16
ICC1 at 2.5 V (mA)
ICC2 at 2.5 V (mA)
ICC1 at 3.3 V (mA)
ICC2 at 3.3 V (mA)
ICC1 at 5 V (mA)
ICC2 at 5 V (mA)
8
Supply Current (mA)
Supply Current (mA)
20
12
8
6
4
2
4
0
0
0
25
50
TA = 25°C
75
100
Data Rate (Mbps)
125
150
0
CL = 15 pF
75
100
Data Rate (Mbps)
125
150
D002
CL = No Load
Figure 1. Supply Current vs Data Rate (With 15-pF Load)
Figure 2. Supply Current vs Data Rate (With No Load)
6
1
5
Low-Level Output Voltage (V)
High-Level Output Voltage (V)
50
TA = 25°C
VCC at 2.5 V
VCC at 3.3 V
VCC at 5.0 V
0.9
4
3
2
VCC at 2.5 V
VCC at 3.3 V
VCC at 5.0 V
1
0
-15
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-10
-5
High-Level Output Current (mA)
0
0
13
VCC1 Rising
VCC1 Falling
VCC2 Rising
VCC2 Falling
Propagation Delay Time (ns)
2.1
2.05
2
1.95
1.9
1.85
1.8
12
11
10
9
tPLH at 2.5 V
tPHL at 2.5 V
tPLH at 3.3 V
1.75
1.7
-50
D004
D001
Figure 4. Low-Level Output Voltage vs Low-Level Output
Current
2.25
2.15
15
TA = 25°C
Figure 3. High-Level Output Voltage vs High-level Output
Current
2.2
5
10
Low-Level Output Current (mA)
D003
TA = 25°C
Power Supply Under-Voltage Threshold (V)
25
D001
0
50
100
Free-Air Temperature (oC)
150
8
-60
-30
D005
Figure 5. Power Supply Undervoltage Threshold vs Free-Air
Temperature
0
30
60
Free-Air Temperature (oC)
tPHL at 3.3 V
tPLH at 5.0 V
tPHL at 5.0 V
90
120
D006
Figure 6. Propagation Delay Time vs Free-Air Temperature
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
11
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
Isolation Barrier
7 Parameter Measurement Information
IN
Input
Generator
Note A
50 W
VI
VCCI
VI
OUT
50%
50%
0V
tPLH
VO
CL
Note B
tPHL
90%
10%
50%
VO
VOH
50%
VOL
tr
tf
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3
ns, tf ≤ 3ns, ZO = 50 Ω. At the input, 50 Ω resistor is required to terminate Input Generator signal. It is not needed in
actual application.
B.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 7. Switching Characteristics Test Circuit and Voltage Waveforms
VCCO
VCC
ISOLATION BARRIER
0V
R L = 1 k W ± 1%
IN
Input
Generator
OUT
EN
VO
0V
tPLZ
tPZL
VO
CL
VCC/2
VCC/2
VI
VCCO
0.5 V
50%
VOL
Note B
VI
50 W
3V
ISOLATION BARRIER
Note A
IN
Input
Generator
Note A
VI
VCC
OUT
VO
VCC/2
VI
VCC/2
0V
EN
50 W
CL
Note B
tPZH
R L = 1 k W ± 1%
VO
VOH
50%
0.5 V
tPHZ
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 10 kHz, 50% duty cycle,
tr ≤ 3 ns, tf ≤ 3 ns, ZO = 50 Ω.
B.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
0V
Figure 8. Enable/Disable Propagation Delay Time Test Circuit and Waveform
12
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
Parameter Measurement Information (continued)
VI
IN = 0 V (Devices without suffix F)
IN = VCC (Devices with suffix F)
A.
VCC
ISOLATION BARRIER
VCC
IN
2.7 V
VI
OUT
0V
t fs
VO
fs high
VO
CL
NOTE A
VOH
50%
fs low V
OL
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 9. Default Output Delay Time Test Circuit and Voltage Waveforms
S1
C = 0.1 μ F ±1%
Isolation Barrier
VCCI
IN
GNDI
VCCO
C = 0.1 μ F ±1%
Pass-fail criteria –
output must remain
stable.
OUT
+
CL
Note A
GNDO
VOH or VOL
–
+ VCM –
A.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 10. Common-Mode Transient Immunity Test Circuit
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
13
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
8 Detailed Description
8.1 Overview
ISO7831 employs an ON-OFF Keying (OOK) modulation scheme to transmit the digital data across a silicon
dioxide based isolation barrier. The transmitter sends a high frequency carrier across the barrier to represent one
digital state and sends no signal to represent the other digital state. The receiver demodulates the signal after
advanced signal conditioning and produces the output through a buffer stage. If the EN pin is low then the output
goes to high impedance. ISO7831 also incorporates advanced circuit techniques to maximize the CMTI
performance and minimize the radiated emissions due the high frequency carrier and IO buffer switching. The
conceptual block diagram of a digital capacitive isolator, Figure 11, shows a functional block diagram of a typical
channel.
8.2 Functional Block Diagram
RECEIVER
TRANSMITTER
EN
TX IN
OOK
MODULATION
TX SIGNAL
CONDITIONING
OSCILLATOR
SiO2 based
Capacitive
Isolation
Barrier
RX SIGNAL
CONDITIONING
ENVELOPE
DETECTION
RX OUT
EMISSIONS
REDUCTION
TECHNIQUES
Figure 11. Conceptual Block Diagram of a Digital Capacitive Isolator
Also a conceptual detail of how the ON/OFF Keying scheme works is shown in Figure 12.
TX IN
Carrier signal
through
isolation barrier
RX OUT
Figure 12. On-Off Keying (OOK) Based Modulation Scheme
14
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
8.3 Feature Description
PRODUCT
CHANNEL DIRECTION
MAX DATA RATE
DEFAULT OUTPUT
ISO7831
2 Forward, 1 Reverse
5700 VRMS / 8000 VPK
(1)
100 Mbps
High
ISO7831
2 Forward, 1 Reverse
5700 VRMS / 8000 VPK
(1)
100 Mbps
Low
(1)
RATED ISOLATION
See Regulatory Information for detailed isolation ratings.
8.3.1 High Voltage Feature Description
8.3.1.1 Package Insulation and Safety-Related Specifications
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
L(I01)
Minimum air gap (clearance)
Shortest terminal-to-terminal distance
through air
DW-16
8
mm
L(I02) (1)
Minimum external tracking
(creepage)
Shortest terminal-to-terminal distance
across the package surface
DW-16
8
mm
CTI
Tracking resistance (comparative
tracking index)
DIN EN 60112 (VDE 0303-11); IEC 60112; UL 746A
600
V
RIO
Isolation resistance, input to
output (2)
VIO = 500 V, TA = 25°C
1012
Ω
11
Ω
CIO
Barrier capacitance, input to
output (2)
VIO = 0.4 x sin (2πft), f = 1 MHz
2
pF
CI
Input capacitance (3)
VI = VCC/2 + 0.4 x sin (2πft), f = 1 MHz, VCC = 5 V
2
pF
(1)
(2)
(3)
VIO = 500 V, 100°C ≤ TA ≤ max
10
Per JEDEC package dimensions.
All pins on each side of the barrier tied together creating a two-terminal device.
Measured from input pin to ground.
NOTE
Creepage and clearance requirements should be applied according to the specific
equipment isolation standards of an application. Care should be taken to maintain the
creepage and clearance distance of a board design to ensure that the mounting pads of
the isolator on the printed-circuit board do not reduce this distance.
Creepage and clearance on a printed-circuit board become equal in certain cases.
Techniques such as inserting grooves and/or ribs on a printed circuit board are used to
help increase these specifications.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
15
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
8.3.1.2 Insulation Characteristics
PARAMETER (1)
DTI
TEST CONDITIONS
Distance through the insulation
VIOWM
SPECIFICATION
Minimum internal gap (internal clearance)
Maximum isolation working voltage
Time dependent dielectric breakdown (TDDB) Test
UNIT
21
μm
1500
VRMS
2121
VDC
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIOTM
Maximum transient isolation voltage
VTEST = VIOTM
t = 60 sec (qualification)
t= 1 sec (100% production)
8000
VPK
VIOSM
Maximum surge isolation voltage
Test method per IEC 60065, 1.2/50 µs waveform,
VTEST = 1.6 x VIOSM = 12800 VPK (qualification)
8000
VPK
VIORM
Maximum repetitive peak isolation voltage
2121
VPK
VPR
Input-to-output test voltage
RS
Isolation resistance
Method a, After Input/Output safety test subgroup
2/3,
VPR = VIORM x 1.2, t = 10 s,
Partial discharge < 5 pC
2545
Method a, After environmental tests subgroup 1,
VPR = VIORM x 1.6, t = 10 s,
Partial Discharge < 5 pC
3394
Method b1,
VPR = VIORM x 1.875, t = 1 s (100% Production test)
Partial discharge < 5 pC
3977
VIO = 500 V at TS
>109
Pollution degree
VPK
Ω
2
UL 1577
VISO
(1)
Withstanding isolation voltage
VTEST = VISO = 5700 VRMS, t = 60 sec
(qualification),
VTEST = 1.2 x VISO = 6840 VRMS, t = 1 sec (100%
production)
5700
VRMS
Climatic Classification 55/125/21
8.3.1.3 IEC 60664-1 Ratings Table
PARAMETER
Basic isolation group
Installation classification
16
TEST CONDITIONS
Material group
SPECIFICATION
I
Rated mains voltage ≤ 600 VRMS
I–IV
Rated mains voltage ≤ 1000 VRMS
I–III
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
8.3.1.4 Regulatory Information
DW package certifications are complete.
VDE
CSA
Certified according to DIN V VDE
V 0884-10 (VDE V 088410):2006-12 and DIN EN 609501 (VDE 0805 Teil 1):2011-01
Approved under CSA
Component Acceptance Notice
5A, IEC 60950-1, IEC 61010-1,
and IEC 60601-1
UL
CQC
Certified according to UL 1577
Component Recognition
Program
Certified according to GB 4943.12011
Reinforced insulation per CSA
61010-1-12 and IEC 61010-1
3rd Ed., 300 VRMS max working
voltage;
Reinforced insulation
Maximum transient isolation
voltage, 8000 VPK;
Maximum repetitive peak
isolation voltage, 2121 VPK;
Maximum surge isolation
voltage, 8000 VPK
Certificate number: 40040142
(1)
Reinforced insulation per CSA
60950-1-07+A1+A2 and IEC
60950-1 2nd Ed., 800 VRMS
max working voltage (pollution
degree 2, material group I) ;
Single protection, 5700 VRMS
(1)
Reinforced Insulation, Altitude ≤
5000 m, Tropical Climate, 250 VRMS
maximum working voltage
2 MOPP (Means of Patient
Protection) per CSA 606011:14 and IEC 60601-1 Ed. 3.1,
250 VRMS (354 VPK) max
working voltage
Master contract number:
220991
File number: E181974
Certificate number:
CQC15001121716
Production tested ≥ 6840 VRMS for 1 second in accordance with UL 1577.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
17
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
8.3.1.5 Safety Limiting Values
Safety limiting intends to prevent potential damage to the isolation barrier upon failure of input or output circuitry. A failure of
the I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to overheat
the die and damage the isolation barrier potentially leading to secondary system failures.
PARAMETER
Safety input, output, or supply
current for DW-16 Package
IS
PS
Safety input, output, or total
power
TS
Maximum case temperature
TEST CONDITIONS
MIN
TYP
MAX
RθJA = 78.9°C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C
288
RθJA = 78.9°C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C
440
RθJA = 78.9°C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C
576
RθJA = 78.9°C/W, TJ = 150°C, TA = 25°C
1584
UNIT
mA
mW
150
°C
The maximum safety temperature is the maximum junction temperature specified for the device. The power
dissipation and junction-to-air thermal impedance of the device installed in the application hardware determines
the junction temperature. The assumed junction-to-air thermal resistance in the Thermal Information is that of a
device installed on a High-K test board for Leaded Surface Mount Packages. The power is the recommended
maximum input voltage times the current. The junction temperature is then the ambient temperature plus the
power times the junction-to-air thermal resistance
1800
700
1600
Safety Limiting Power (mW)
600
Safety Limiting Current (mA)
Power
VCC1 = VCC2 = 2.75 V
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
500
400
300
200
100
1200
1000
800
600
400
200
0
0
0
50
100
150
Ambient Temperature (qC)
200
Figure 13. Thermal Derating Curve per VDE for
DW-16 Package
18
1400
0
D014
50
100
150
Ambient Temperature (qC)
200
D015
Figure 14. Thermal Derating Curve for Safety Limiting
Power per VDE
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
8.4 Device Functional Modes
ISO7831 functional modes are shown in Table 1.
Table 1. Function Table (1)
VCCI
VCCO
PU
PU
X
(1)
(2)
(3)
INPUT
(INx) (2)
OUTPUT
ENABLE
(ENx)
OUTPUT
(OUTx)
H
H or open
H
L
H or open
L
Open
H or open
Default
X
L
Z
PU
COMMENTS
Normal Operation:
A channel output assumes the logic state of its input.
A low value of Output Enable causes the outputs to be highimpedance
Default mode: When VCCI is unpowered, a channel output assumes
the logic state based on the selected default option.
When VCCI transitions from unpowered to powered-up, a channel
output assumes the logic state of its input.
When VCCI transitions from powered-up to unpowered, channel output
assumes the selected default state.
PD
PU
X
H or open
Default
X
PD
X
X
Undetermined
When VCCO is unpowered, a channel output is undetermined (3).
When VCCO transitions from unpowered to powered-up, a channel
output assumes the logic state of its input
VCCI = Input-side VCC; VCCO = Output-side VCC; PU = Powered up (VCC ≥ 2.25 V); PD = Powered down (VCC ≤ 1.7 V); X = Irrelevant; H
= High level; L = Low level ; Z = High Impedance
A strongly driven input signal can weakly power the floating VCC via an internal protection diode and cause undetermined output.
The outputs are in undetermined state when 1.7 V < VCCI, VCCO < 2.25 V.
8.4.1 Device I/O Schematics
Input (Devices without suffix F)
VCCI
VCCI
Enable
VCCI
VCCI
VCCO
VCCO VCCO
1.5 MW
VCCO
2 MW
985 W
1970 W
INx
ENx
Output
Input (Devices with suffix F)
VCCI
VCCI
VCCO
VCCI
~20 W
985 W
OUTx
INx
1.5 MW
Figure 15. Device I/O Schematics
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
19
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The ISO7831 is a high-performance, quad-channel digital isolator with 5.7 kVRMS isolation voltage. The device
comes with enable pins on each side which can be used to put the respective outputs in high impedance for
multi master driving applications and reduce power consumption. ISO7831 uses single-ended CMOS-logic
switching technology. Its supply voltage range is from 2.25 V to 5.5 V for both supplies, VCC1 and VCC2. When
designing with digital isolators, it is important to keep in mind that due to the single-ended design structure,
digital isolators do not conform to any specific interface standard and are only intended for isolating single-ended
CMOS or TTL digital signal lines. The isolator is typically placed between the data controller (that is, μC or
UART), and a data converter or a line transceiver, regardless of the interface type or standard.
9.2 Typical Application
The Isolated SPI Interface is shown in Figure 16.
VIN
3.3V
0.1F
2
Vcc D2 3
1:2.2 MBR0520L
1
SN6501
GND D1
3
1
10F
OUT
5
TPS76350
10F 0.1F
4,5
IN
EN
GND
2
5VISO
10F
MBR0520L
ISO-BARRIER
0.1F
0.1F
0.1F
DVcc
6
11
3
MSP430 UCA0TXD 15
F2132
16
4
P3.0
XOUT
XIN
UCA0RXD
DVss
4
16
1
2
5
0.1F
5
VCC1
VCC2
INA
OUTA
ISO7831
INB
OUTC
7 EN1
GND1
2,8
OUTB
INC
VCC
14
13
12
EN2 10
GND2
2
3
4
1
RE
DE
10 MELF
B
D
SN65HVD
3082E A
R
GND
10 MELF
SM712
9,15
4.7nF/
2kV
Figure 16. Isolated SPI Interface for an Analog Input Module With 16 Input
20
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
Typical Application (continued)
9.2.1 Design Requirements
For ISO7831, use the parameters shown in Table 2.
Table 2. Design Parameters
PARAMETER
VALUE
Supply voltage
2.25 to 5.5 V
Decoupling capacitor between VCC1 and GND1
0.1 µF
Decoupling capacitor from VCC2 and GND2
0.1 µF
9.2.2 Detailed Design Procedure
Unlike optocouplers, which need external components to improve performance, provide bias, or limit current,
ISO7831 only needs two external bypass capacitors to operate.
2 mm max from VCC2
2 mm max from VCC1
0.1 µF
0.1 µF
VCC1
VCC2
1
16
2
15
INA
3
14
OUTA
INB
4
13
OUTB
OUTC
5
12
INC
6
11
7
10
8
9
GND1
NC
GND2
NC
EN2
EN1
GND1
GND2
Figure 17. Typical ISO7831 Circuit Hook-up
9.2.2.1 Electromagnetic Compatibility (EMC) Considerations
Many applications in harsh industrial environment are sensitive to disturbances such as electrostatic discharge
(ESD), electrical fast transient (EFT), surge and electromagnetic emissions. These electromagnetic disturbances
are regulated by international standards such as IEC 61000-4-x and CISPR 22. Although system-level
performance and reliability depends, to a large extent, on the application board design and layout, the ISO7831
incorporate many chip-level design improvements for overall system robustness. Some of these improvements
include:
• Robust ESD protection for input and output signal pins and inter-chip bond pads.
• Low-resistance connectivity of ESD cells to supply and ground pins.
• Enhanced performance of high voltage isolation capacitor for better tolerance of ESD, EFT and surge events.
• Bigger on-chip decoupling capacitors to bypass undesirable high energy signals through a low impedance
path.
• PMOS and NMOS devices isolated from each other by using guard rings to avoid triggering of parasitic
SCRs.
• Reduced common mode currents across the isolation barrier by ensuring purely differential internal operation.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
21
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
9.2.3 Application Curve
Typical eye diagram of ISO7831 indicate low jitter and wide open eye at the maximum data rate of 100 Mbps.
Figure 18. Eye Diagram at 100 Mbps PRBS, 5 V and 25°C
10 Power Supply Recommendations
To ensure reliable operation at all data rates and supply voltages, a 0.1-µF bypass capacitor is recommended at
input and output supply pins (VCC1 and VCC2). The capacitors should be placed as close to the supply pins as
possible. If only a single primary-side power supply is available in an application, isolated power can be
generated for the secondary-side with the help of a transformer driver such as Texas Instruments' SN6501. For
such applications, detailed power supply design and transformer selection recommendations are available in
SN6501 data sheet (SLLSEA0).
22
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
ISO7831, ISO7831F
www.ti.com
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
11 Layout
11.1 Layout Guidelines
A minimum of four layers is required to accomplish a low EMI PCB design (see Figure 19). Layer stacking should
be in the following order (top-to-bottom): high-speed signal layer, ground plane, power plane and low-frequency
signal layer.
• Routing the high-speed traces on the top layer avoids the use of vias (and the introduction of their
inductances) and allows for clean interconnects between the isolator and the transmitter and receiver circuits
of the data link.
• Placing a solid ground plane next to the high-speed signal layer establishes controlled impedance for
transmission line interconnects and provides an excellent low-inductance path for the return current flow.
• Placing the power plane next to the ground plane creates additional high-frequency bypass capacitance of
approximately 100 pF/inch2.
• Routing the slower speed control signals on the bottom layer allows for greater flexibility as these signal links
usually have margin to tolerate discontinuities such as vias.
If an additional supply voltage plane or signal layer is needed, add a second power / ground plane system to the
stack to keep it symmetrical. This makes the stack mechanically stable and prevents it from warping. Also the
power and ground plane of each power system can be placed closer together, thus increasing the high-frequency
bypass capacitance significantly.
For detailed layout recommendations, see application note SLLA284, Digital Isolator Design Guide.
11.1.1 PCB Material
For digital circuit boards operating below 150 Mbps, (or rise and fall times higher than 1 ns), and trace lengths of
up to 10 inches, use standard FR-4 epoxy-glass as PCB material. FR-4 (flame retardant 4) meets the
requirements of Underwriters Laboratories UL94-V0, and is preferred over cheaper alternatives due to its lower
dielectric losses at high frequencies, less moisture absorption, greater strength and stiffness, and its selfextinguishing flammability-characteristics.
11.2 Layout Example
High-speed traces
10 mils
Ground plane
40 mils
Keep this
space free
from planes,
traces , pads,
and vias
FR-4
0r ~ 4.5
Power plane
10 mils
Low-speed traces
Figure 19. Layout Example Schematic
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
23
ISO7831, ISO7831F
SLLSEP8A – JULY 2015 – REVISED SEPTEMBER 2015
www.ti.com
12 Device and Documentation Support
12.1 Documentation Support
SN6501 Transformer Driver for Isolated Power Supplies, SLLSEA0
Digital Isolator Design Guide, SLLA284, .
12.1.1 Related Documentation
See the Isolation Glossary (SLLA353)
12.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
ISO7831
Click here
Click here
Click here
Click here
Click here
ISO7831F
Click here
Click here
Click here
Click here
Click here
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
24
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: ISO7831 ISO7831F
PACKAGE OUTLINE
DW0016B
SOIC - 2.65 mm max height
SCALE 1.500
SOIC
C
PIN 1 ID
AREA
A
10.63
TYP
9.97
SEATING PLANE
0.1 C
16
1
14X 1.27
2X
8.89
10.5
10.1
NOTE 3
8
9
B
7.6
7.4
NOTE 4
0.51
0.31
0.25
C A
16X
2.65 MAX
B
0.38
TYP
0.25
SEE DETAIL A
0.25
GAGE PLANE
0.3
0.1
0 -8
1.27
0.40
(1.4)
DETAIL A
TYPICAL
4221009/A 08/2013
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm, per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm, per side.
5. Reference JEDEC registration MO-013, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
DW0016B
SOIC - 2.65 mm max height
SOIC
SYMM
16X (2)
1
SYMM
16X (1.65)
SEE
DETAILS
SEE
DETAILS
1
16
16
16X (0.6)
16X (0.6)
SYMM
SYMM
14X (1.27)
14X (1.27)
9
8
9
8
(9.75)
(9.3)
HV / ISOLATION OPTION
8.1 mm CLEARANCE/CREEPAGE
IPC-7351 NOMINAL
7.3 mm CLEARANCE/CREEPAGE
LAND PATTERN EXAMPLE
SCALE:4X
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
0.07 MAX
ALL AROUND
METAL
0.07 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4221009/A 08/2013
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DW0016B
SOIC - 2.65 mm max height
SOIC
SYMM
16X (2)
SYMM
16X (1.65)
1
1
16
16X (0.6)
16
16X (0.6)
SYMM
SYMM
14X (1.27)
14X (1.27)
9
8
9
8
(9.3)
(9.75)
IPC-7351 NOMINAL
7.3 mm CLEARANCE/CREEPAGE
HV / ISOLATION OPTION
8.1 mm CLEARANCE/CREEPAGE
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:4X
4221009/A 08/2013
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO7831DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7831
ISO7831DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7831
ISO7831FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7831F
ISO7831FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7831F
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ISO7831DWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7831FDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
25-Sep-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ISO7831DWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7831FDWR
SOIC
DW
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages