Willow DG79B-3021-70H-SL12-P Industrial bistable (latching) power relay Datasheet

DG79 / DG79B
industrial bistable (latching) power relay
• Up to 120A /240VAC continuous rating
• Custom Termination options inc shunts
• Single Coil & Twin Coil Latching
• Utility / Prepayment meters
• Automotive / Electric Vehicle Battery
• IEC 62055-31UC3
Contacts
Contact number & arrangement
SPST-NO, SPST-NC (as delivered condition)
Contact material
AgSnO2
Max. switching voltage
250VAC / 30VDC
Min. switching current / voltage
500mA/12VDC
Max. continuous current
DG79: 100A / DG79B: 120A
Short circuit carrying capacity
3000A (Utilization Category UC3)
Max. switching power
DG79: 25000VA / DG79B: 30000VA
Initial resistance
≤ 100mΩ, max. at 0.1A/6VDC (typically 0.25 to 0.5mΩ)
Coil
Rated voltage
5...48VDC
Operating range of supply voltage
See coil table 1
Rated power consumption
Single coil 2.3W
Twin coil 4.6W
Insulation
Insulation resistance
>1000MΩ at 500VDC, 50%RH
Dielectric strength
coil to contact 4000Vrms, 1min (50Hz)
between open contacts 1800Vrms, 1min (50Hz)
Creepage & Clearance >8mm
General Data
Operating time (max.)
mS 20
Release time (max.)
mS 20
Electrical Life
ops 1 x 104
Mechanical life
ops 1 x 106
Dimensions
Weight
L x W x H 52 x 43 x 22mm (see drawings for detail)
approx. 80g (depending on options)
Ambient temperature
storage -40 to 85°C
operating -40 to 85°C (Class F)
Shock resistance
Functional: 100m/s2 11mS; Destructive: 1000m/s2
Vibration resistance
10-55Hz: DA 1.5mm
Humidity
98%RH, 40°C
Page 1 of 3
Ref: DG79 051514JHM
www.durakoolrelays.com
Sales Department Tel: (888) 847-6552
DG79 / DG79B
industrial bistable (latching) power relay
Coil Data
Table 1
DC Coil
Coil Voltage Code
Coil Resistance (Ω) ±10%
Must operate
voltage
(VDC)
Single Coil
Twin Coil*
Nominal Voltage
(VDC)
SL05
TL05
5
22
11 + 11
≥3.75
SL09
TL09
9
35
18 + 18
≥ 6.75
SL12
TL12
12
63
31 + 31
≥ 9.0
SL24
TL24
24
250
125 + 125
≥ 18.0
SL48
TL48
48
1002
501 + 501
≥ 36.0
Single Coil
(2.3W)
Twin Coil*
(4.6W)
Operate pulse
length
(mS)
100
* NB: For twin coil, latch & reset coils must not be powered simultaneously.
Twin Coil type can be used as single coil type by ignoring centre connection (Pin 2 - see Wiring Diagram, Fig. 3).
Other coil voltages available to special order, subject to minimum order quantity.
Ordering codes
Contact
Material
Type
D
G
7
9
Contact
arrangement
-
Cover protection and
mounting
-
Coil code
-
-
Model type
DG79
100A Rating
DG79B
120A Rating
Contact Material
30
-
see Table 1
AgSnO2
Contact Arrangement
21
-
SPST-NO (1 Normally open) *
31
-
SPST-NC (1 Normally closed)*
* As delivered condition.
Cover Protection Category
7
-
Covered, dust cover
Terminations and mounting (refer to Dimensional Drawings)*
0H
-
PCB coil terminals + horizontal power terminals.
0V
-
PCB coil terminals + vertical power terminals.
1V
-
PCB coil terminals + vertical power terminals.
2V
-
PCB coil terminals + vertical power terminals with integral shunt.
(Use with “P” custom option to define shunt)
* Custom terminations available. Please contact factory.
Options
Page 2 of 3
NIL
-
Standard
P***
-
Custom (*** = unique identifier)
Ref: DG79 0515141JHM
www.durakoolrelays.com
Sales Department Tel: (888) 847-6552
DG79 / DG79B
industrial bistable (latching) power relay
Overall Dimensions
Fig. 1
DG79 “0H” Type
DG79 “0V” Type
DG79 “1V” Type
DG79 “2V” Type (with shunt)
All dimensions in mm
Custom terminations available upon request
Fig. 3
Wiring Diagram
contacts shown in operated position
coil
coil
pin 2
pin 1
+ ve
pin 3
release
pin 1 pin 2 pin 3
Notes:
1) All parameters, unless otherwise specified, are measured at an ambient temperature of 23°C.
Specifications are subject to change without notice. E&OE.
Page 3 of 3
Ref: DG79 051514JHM
American Electronic Components Inc., 1101 Lafayette St. Elkhart, IN46516
www.durakoolrelays.com
Sales Department Tel: (888) 847-6552
- ve
operate
+ ve
Similar pages