EPCOS B82111B0000C013 Inductor Datasheet

Inductors
VHF chokes
Series/Type:
B82111B
Date:
June 2012
Data Sheet
¤EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
VHF chokes
B82111B
Rated voltage 500 V AC/DC
Rated current 2 ... 10 A
Rated inductance 3 ... 25 μH
Construction
■ Ferrite cylinder core
■ Winding: single-layer, enamel copper wire,
winding ends brought out as leads
■ Polyester insulating sleeve
Features
■
■
■
■
■
High resonant frequency
High rated current
Suitable for wave soldering
RoHS-compatible
ENEC10 approval
Applications
■ RF blocking and filtering
■ Interference suppression in small appliances
Terminals
■ Central axial leads
■ Base material Cu
■ Hot-dip tinned with pure tin
Marking
LR and IR in clear text and approval mark
Delivery mode
Bulk
102 _ 5
ød2
Dimensional drawing
l1
l2
ød1
IND0626-L
Dimensions in mm
Please read Cautions and warnings and
Important notes at the end of this document.
2
06/12
VHF chokes
B82111B
Technical data and measuring conditions
Test voltage Vtest
2500 V AC, 1 min
Rated inductance LR
Measured with LCR meter Agilent 4284A
or impedance analyzer Agilent 4294A
Measuring frequency:
LR d 10 PH
= 1 MHz
10 PH < LR d 1000 PH = 100 kHz
Measuring voltage:
1V
Measuring temperature: +20 °C
Inductance tolerance
r20%
Rated temperature TR
+60 °C
Rated current IR
Maximum permissible DC current at rated temperature
DC resistance Rtyp
Measured at +20 qC, tolerance r20%, typical values
Resonance frequency fres
Measured with Agilent 4294A or 8753ES, +20 °C
tolerance r30%
Solderability (lead-free)
Sn95.5Ag3.8Cu0.7: +(245 r5) °C, (3 r0.3) s
Wetting of soldering area t90%
(to IEC 60068-2-20, test Ta)
Resistance to soldering heat
(wave soldering)
+(260 r5) °C, 10 s
(to IEC 60068-2-20, test Tb)
Tensile strength of leads
t30 N (to IEC 60068-2-21, test Ua)
Climatic category
55/125/56 (to IEC 60068-1)
Storage conditions
Mounted: –55 °C … +125 °C
Packaged: –25 °C … +40 °C, d75% RH
Approvals
EN 60938
Mounting information
When bending the leads, take care that the bending point is at least 3 mm apart from the face ends
of the core and that the start-of-winding areas are not subjected to any mechanical stress.
Please read Cautions and warnings and
Important notes at the end of this document.
3
06/12
VHF chokes
B82111B
Characteristics and ordering codes
LR
Rtyp
fres
PH
:
MHz l1–1.5
l2–3
d1 max. d2
2
17
0.063
100
18.3
24
7.0
0.45
3.0
3
3
3
3
4
4
4
6
6
6
9
10
8
13
20
25
6
11
15
4
6
9
3
5
0.025
0.024
0.054
0.046
0.017
0.020
0.024
0.014
0.010
0.012
0.006
0.005
145
170
125
85
170
150
120
205
200
150
220
175
18.3
24.5
24.5
28.5
18.3
24.5
28.5
18.3
24.5
28.5
24.5
28.5
24
29
29
34
24
29
34
24
29
34
29
34
7.0
6.5
6.0
8.5
7.5
6.5
8.5
7.5
7.0
9.0
7.5
9.5
0.63
0.67
0.5
0.63
0.75
0.71
0.75
0.8
0.95
0.95
1.2
1.3
3.0
3.5
3.5
6.0
3.0
6.0
7.0
4.0
5.0
8.0
5.0
10.0
IR
Dimensions (mm)
Approx.
weight
g
Ordering code
Approvals
B82111B0000C014 u
B82111B0000C013
B82111B0000C019
B82111B0000C020
B82111B0000C024
B82111B0000C012
B82111B0000C018
B82111B0000C023
B82111B0000C011
B82111B0000C017
B82111B0000C022
B82111B0000C016
B82111B0000C021
u
u
u
u
u
u
u
u
u
u
u
u
u = approval granted
Impedance |Z| versus frequency f
measured with impedance analyzer Agilent 4294A or S-parameter network analyzer
Agilent 8753ES, typical values at +20 °C
B82111B0000C011…C014
IND0154-3
10 6
Ω
B82111B0000C016…C020
IND0155-1
10 6
B82111B
Ω
|Z |
B82111B
|Z|
10 5
10 5
10 4
10 4
C014
C013
C012
C011
10 3
10 2 7
10
10 8
10 3
Hz
f
Please read Cautions and warnings and
Important notes at the end of this document.
10 2 7
10
10 9
4
06/12
C020
C019
C018
C017
C016
10 8
Hz
f
10 9
VHF chokes
B82111B
Current derating Iop/IR
versus ambient temperature TA
Impedance |Z| versus frequency f
measured with impedance analyzer Agilent
4294A or S-parameter network analyzer
Agilent 8753ES, typical values at +20 °C
(rated temperature TR = +60 °C)
B82111B0000C021…C024
IND0156-R
10 6
Ω
B82111B
I op
IR
|Z|
10
IND0143-T-E
1.2
1.0
5
0.8
10 4
0.6
0.4
10 3
10 2 7
10
C024
C023
C022
C021
10 8
0.2
Hz
f
0
10 9
0
20
40
60
80
100
˚C
TA
5
06/12
140
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
6
06/12
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
7
06/12
Similar pages