TI1 OPA4374AIPWRG4 6.5mhz, 585mua, rail-to-rail i/o cmos operational amplifier Datasheet

OPA373, OPA2373
OPA374
OPA2374, OPA4374
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
6.5MHz, 585µA, Rail-to-Rail I/O
CMOS Operational Amplifier
FEATURES
D
D
D
D
D
D
D
D
DESCRIPTION
LOW OFFSET: 5mV (max)
LOW IB: 10pA (max)
HIGH BANDWIDTH: 6.5MHz
RAIL-TO-RAIL INPUT AND OUTPUT
SINGLE SUPPLY: +2.3V to +5.5V
SHUTDOWN: OPAx373
SPECIFIED UP TO +125°C
MicroSIZE PACKAGES: SOT23-5, SOT23-6,
SOT23-8 and DFN-10
The OPA373 and OPA374 families of operational
amplifiers are low power and low cost with excellent
bandwidth (6.5MHz) and slew rate (5V/µs). The input
range extends 200mV beyond the rails and the output
range is within 25mV of the rails. The speed/power ratio
and small size make them ideal for portable and
battery-powered applications.
The OPA373 family includes a shutdown mode. Under
logic control, the amplifiers can be switched from normal
operation to a standby current that is less than 1µA.
APPLICATIONS
D
D
D
D
PORTABLE EQUIPMENT
BATTERY-POWERED DEVICES
ACTIVE FILTERS
DRIVING A/D CONVERTERS
OPA374
OPA373
1
V−
2
+IN
A75
Out
3
The OPA373 and OPA374 families of operational
amplifiers are specified for single or dual power supplies
of +2.7V to +5.5V, with operation from +2.3V to +5.5V. All
models are specified for −40°C to +125°C.
6
V+
5
Enable
4
Out
1
V−
2
−IN
+IN
OPA2373
5
V+
OUT A
1
−IN A 2
4
3
−IN
+IN A
10 V+
9
OUT B
8
−IN B
A
3
B
SOT23−6(1)
V−
4
7
+IN B
Enable A
5
6
Enable B
SOT23−5
OPA373
OPA2373
MSOP−10
NC(2)
1
8
Enable
−IN
2
7
V+
V+
OUT A
Exposed
thermal
die pad on
underside
(Must be
connected to V−)
−IN A
OPA4374
+IN A
+IN
3
6
OUT
OUT A
1
V−
4
5
NC(2)
−IN A
2
+IN A
SO−8
OPA374
NC(2)
−IN
+IN
V−
1
8
2
7
3
4
NC(2)
14
OUT D
13
−IN D
3
12
+IN D
V+
4
11
V−
+IN B
5
10
+IN C
9
−IN C
8
OUT C
−IN B
6
OUT B
7
A
B
D
C
V+
6
OUT
5
NC(2)
SO−14, TSSOP−14
V−
OUT B
−IN B
+IN B
Enable B
Enable A
DFN−10
OPA2374
OUT A
1
−IN A 2
+IN A
3
V−
4
A
B
8
V+
7
OUT B
6
−IN B
5
+IN B
SO−8, SOT23−8
SO−8
(1) Pin 1 of the SOT23-6 is determined by orienting the package marking as shown.
(2) NC indicates no internal connection.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright  2003-2008, Texas Instruments Incorporated
! ! www.ti.com
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
PACKAGE/ORDERING INFORMATION(1)
PRODUCT
PACKAGE-LEAD
PACKAGE
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
Shutdown
OPA373
″
OPA373
″
OPA2373
″
OPA2373
″
SOT23-6
″
SO-8
″
MSOP-10
″
DFN-10
″
DBV
″
D
″
DGS
″
DRC
″
−40°C to +125°C
″
−40°C to +125°C
″
−40°C to +125°C
″
−40°C to +125°C
″
A75
″
OPA373A
″
AYO
″
OCEQ
″
OPA373AIDBVT
OPA373AIDBVR
OPA373AID
OPA373AIDR
OPA2373AIDGST
OPA2373AIDGSR
OPA2373AIDRCT
OPA2373AIDRCR
Tape and Reel, 250
Tape and Reel, 3000
Rails, 100
Tape and Reel, 2500
Tape and Reel, 250
Tape and Reel, 2500
Tape and Reel, 250
Tape and Reel, 3000
Non-Shutdown
OPA374
SOT23-5
DBV
−40°C to +125°C
A76
OPA374AIDBVT
Tape and Reel, 250
″
″
″
″
″
OPA374AIDBVR Tape and Reel, 3000
OPA374
SO-8
D
−40°C to +125°C
OPA274A
OPA374AID
Rails, 100
″
″
″
″
″
OPA374AIDR
Tape and Reel, 2500
OPA2374
SOT23-8
DCN
−40°C to +125°C
ATP
OPA2374AIDCNT Tape and Reel, 250
″
″
″
″
″
OPA2374AIDCNR Tape and Reel, 3000
OPA2374
SO-8
D
−40°C to +125°C
OPA2374A
OPA2374AID
Rails, 100
″
″
″
″
″
OPA2374AIDR
Tape and Reel, 2500
OPA4374
SO-14
D
−40°C to +125°C
OPA4374A
OPA4374AID
Rails, 58
″
″
″
″
″
OPA4374AIDR
Tape and Reel, 2500
OPA4374
TSSOP-14
PW
−40°C to +125°C
OPA4374A
OPA4374AIPWT
Tape and Reel, 250
″
″
″
″
″
OPA4374AIPWR Tape and Reel, 2500
(1) For the most current package and ordering information, see the Package Option Addendum located at the end of this datasheet.
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V
Signal Input Terminals, Voltage(2) . . . . . . . . . −0.5V to (V+) + 0.5V
Current(2) . . . . . . . . . . . . . . . . . . . ±10mA
Output Short-Circuit(3) . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Operating Temperature . . . . . . . . . . . . . . . . . . . . . −55°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . +300°C
(1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(2) Input terminals are diode-clamped to the power-supply rails.
Input signals that can swing more than 0.5V beyond the supply
rails should be current-limited to 10mA or less.
(3) Short-circuit to ground, one amplifier per package.
2
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handled with appropriate precautions. Failure to observe
proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
ELECTRICAL CHARACTERISTICS: VS = +2.7V to +5.5V
Boldface limits apply over the specified temperature range, TA = −40°C to +125°C.
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
OPA373, OPA2373, OPA374,
OPA2374, OPA4374
PARAMETER
OFFSET VOLTAGE
Input Offset Voltage
over Temperature
Drift
vs Power Supply
over Temperature
Channel Separation, DC
f = 1kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
over Temperature
CONDITIONS
VOS
dVOS/dT
PSRR
VS = 5V
OPEN-LOOP GAIN
Open-Loop Voltage Gain
over Temperature
VCM
CMRR
(V−) − 0.2V < VCM < (V+) − 2V
(V−) − 0.2V < VCM < (V+) − 2V
VS = 5.5V, (V−) − 0.2V < VCM < (V+) + 0.2V
VS = 5.5V, (V−) − 0.2V < VCM < (V+) + 0.2V
(V−) − 0.2
80
70
66
60
ENABLE/SHUTDOWN
tOFF
tON
VL (shutdown)
VH (amplifier is active)
Input Bias Current of Enable Pin
IQSD (per amplifier)
1
5
6.5
mV
mV
µV/°C
µV/V
µV/V
µV/V
dB
100
150
(V+) + 0.2
V
dB
dB
dB
dB
±10
±10
pA
pA
90
1013 3
1013 6
Ω pF
Ω pF
10
15
4
µVPP
nV/√Hz
fA/√Hz
110
dB
dB
dB
dB
VCM < (V+) − 2V
en
in
AOL
OUTPUT
Voltage Output Swing from Rail
over Temperature
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
Settling Time, 0.1%
0.01%
Overload Recovery Time
Total Harmonic Distortion + Noise
UNIT
±0.5
±0.5
IB
IOS
over Temperature
over Temperature
Short-Circuit Current
Capacitive Load Drive
Open-Loop Output Impedance
MAX
3
25
VS = 2.7V to 5.5V, VCM < (V+) − 2V
VS = 2.7V to 5.5V, VCM < (V+) − 2V
INPUT IMPEDANCE
Differential
Common-Mode
NOISE
Input Voltage Noise, f = 0.1Hz to 10Hz
Input Voltage Noise Density, f = 10kHz
Input Current Noise Density, f = 10kHz
TYP
0.4
128
over Temperature
INPUT BIAS CURRENT
Input Bias Current
Input Offset Current
MIN
VS = 5V, RL = 100kΩ, 0.025V < VO < 4.975V
VS = 5V, RL = 100kΩ, 0.025V < VO < 4.975V
VS = 5V, RL = 5kΩ, 0.125V < VO < 4.875V
VS = 5V, RL = 5kΩ, 0.125V < VO < 4.875V
RL = 100kΩ
RL = 100kΩ
RL = 5kΩ
RL = 5kΩ
ISC
CLOAD
f = 1MHz, IO = 0
94
80
94
80
106
18
25
25
100
125
125
See Typical Characteristics
See Typical Characteristics
220
mV
mV
mV
mV
6.5
5
1
1.5
0.3
0.0013
MHz
V/µs
µs
µs
µs
%
3
12
µs
µs
V
V
µA
µA
Ω
CL = 100pF
GBW
SR
tS
THD+N
G = +1
VS = 5V, 2V Step, G = +1
VS = 5V, 2V Step, G = +1
VIN • Gain > VS
VS = 5V, VO = 3VPP, G = +1, f = 1kHz
V−
(V−) + 0.8
V+
(V−) + 2
0.2
< 0.5
1
3
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
ELECTRICAL CHARACTERISTICS: VS = +2.7V to +5.5V (continued)
Boldface limits apply over the specified temperature range, TA = −40°C to +125°C.
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
OPA373, OPA2373, OPA374,
OPA2374, OPA4374
PARAMETER
POWER SUPPLY
Specified Voltage Range
Operating Voltage Range
Quiescent Current (per amplifier)
over Temperature
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SOT23-5, SOT23-6, SOT23-8
MSOP-10, SO-8
SO-14, TSSOP-14
DFN-10
4
CONDITIONS
VS
IQ
MIN
TYP
2.7
2.3 to 5.5
585
IO = 0
−40
−55
−65
UNIT
5.5
V
V
µA
µA
750
800
+125
+150
+150
qJA
JEDEC High-K Board
MAX
200
150
100
56
°C
°C
°C
°C/W
°C/W
°C/W
°C/W
°C/W
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
TYPICAL CHARACTERISTICS
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
POWER−SUPPLY AND COMMON−MODE
REJECTION RATIO vs FREQUENCY
120
100
0
100
Gain
80
−30
60
−60
40
−90
Phase
20
−120
0
−150
−20
10
100
1k
10k
100k
1M
PSRR and CMRR (dB)
30
Phase Margin (_)
Open−Loop Gain (dB)
OPEN−LOOP GAIN AND PHASE vs FREQUENCY
120
CMRR
80
PSRR
60
40
20
0
−180
10M
100
1k
10k
10M
0.100
Total Harmonic Distortion+Noise (%)
1000
Voltage Noise (nV/√Hz)
1M
TOTAL HARMONIC DISTORTION+NOISE
vs FREQUENCY
INPUT VOLTAGE NOISE
SPECTRAL DENSITY vs FREQUENCY
100
RL = 5kΩ
G = 10V/V
0.010
G = 1V/V
0.001
10
10
100
1k
10k
10
100k
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
OPEN−LOOP GAIN AND POWER−SUPPLY
REJECTION RATIO vs TEMPERATURE
COMMON−MODE REJECTION RATIO vs TEMPERATURE
120
130
VS = 5.5V
RL = 100kΩ
110
120
VCM = −0.2V to 3.5V
100
CMRR (dB)
AOL, PSRR (dB)
100k
Frequency (Hz)
Frequency (Hz)
110
RL = 5kΩ
100
PSRR
90
80
VCM = −0.2V to 5.7V
70
60
90
50
80
40
−50
−25
0
25
50
75
Temperature (_ C)
100
125
150
−50
−25
0
25
50
75
100
125
150
Temperature (_C)
5
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
QUIESCENT CURRENT vs SUPPLY VOLTAGE
QUIESCENT CURRENT vs TEMPERATURE
800
800
VOUT = 1/2[(V+) − (V−)]
Quiescent Current (µA)
Quiescent Current (µA)
700
600
500
400
300
700
600
500
400
−50
−25
300
0
25
50
75
100
125
150
2.0
3.0
4.5
5.0
5.5
CONTINUOUS SHORT−CIRCUIT CURRENT vs
POWER−SUPPLY VOLTAGE
12
+ISC
Short−Circuit Current (mA)
+ISC
12
10
8
−ISC
6
4
2
10
8
−ISC
6
4
2
0
0
−50
−25
0
25
50
75
100
2.0
125
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Power−Supply Voltage (V)
Temperature (_ C)
INPUT BIAS CURRENT vs TEMPERATURE
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
3
10k
2
1k
Output Voltage (V)
Input Bias Current (pA)
4.0
SHORT−CIRCUIT CURRENT vs TEMPERATURE
14
100
10
1
1
0
−1
−55_ C
25_C
150_C
−2
−3
0.1
−50
−25
0
25
50
Temperature (_ C)
6
3.5
Supply Voltage (V)
16
Short−Circuit Current (mA)
2.5
Temperature (_C)
75
100
125
0
2
4
6
8
10
12
Output Current (mA)
14
16
18
20
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
6
VS = 5.5V
VS = 5V
4
3
Population
Output Voltage (VPP )
5
VS = 2.5V
2
1
0
10k
100k
1M
−5
10M
−4
−3
Frequency (Hz)
−2
−1
0
1
2
3
4
5 5.5
Offset Voltage (mV)
OFFSET VOLTAGE DRIFT MAGNITUDE
PRODUCTION DISTRIBUTION
SMALL−SIGNAL STEP RESPONSE
CL = 100pF
Population
50mV/div
Typical production distribution
of packaged units.
1
2
3
4
5
6
7
8
200ns/div
9 10 11 12 13 14 15 16
Offset Voltage Drift (µV/_C)
LARGE −SIGNAL STEP RESPONSE
SMALL−SIGNAL OVERSHOOT vs LOAD CAPACITANCE
50
Refer to the Capacitive Load
and Stability section for tips
on improving performance.
CL = 100pF
40
1V/div
Small−Signal Overshoot (%)
60
G = +1V/V
30
20
G = ±10V/V
RFB = 10kΩ
10
0
10
100
1k
10k
400ns/div
Load Capacitance (pF)
7
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
CHANNEL SEPARATION vs FREQUENCY
SETTLING TIME vs CLOSED−LOOP GAIN
140
Channel Separation (dB)
Settling Time (µs)
100
10
0.01%
0.1%
1
G = +1V/V, All Channels
RL = 5kΩ
120
100
80
60
40
20
0.1
0
1
10
Closed−Loop Gain (V/V)
8
100
10
100
1K
10K
100K
Frequency (Hz)
1M
10M
100M
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
APPLICATIONS
The input common-mode voltage range includes both
rails, allowing the OPA373 and OPA374 series op amps to
be used in virtually any single-supply application up to a
supply voltage of +5.5V.
1.5
Offset Voltage (mV)
The OPA373 and OPA374 series op amps are unity-gain
stable and suitable for a wide range of general-purpose
applications. Rail-to-rail input and output make them ideal
for driving sampling Analog-to-Digital Converters (ADCs).
Excellent ac performance makes them well-suited for
audio applications. The class AB output stage is capable
of driving 100kΩ loads connected to any point between V+
and ground.
2.0
1.0
0.5
0
−0.5
−1.0
−1.5
−2.0
− 0.5 0
V−
V+
0.5 1.0 1.5
2.0 2.5
3.0 3.5 4.0 4.5 5.0 5.5
6.0
Common−Mode Voltage (V)
Rail-to-rail input and output swing significantly increases
dynamic range, especially in low-supply applications.
Figure 1. Behavior of Typical Transition Region at
Room Temperature
Power-supply pins should be bypassed with 0.01µF
ceramic capacitors.
RAIL-TO-RAIL INPUT
OPERATING VOLTAGE
The OPA373 and OPA374 op amps are specified and
tested over a power-supply range of +2.7V to +5.5V
(±1.35V to ±2.75V). However, the supply voltage may
range from +2.3V to +5.5V (±1.15V to ±2.75V). Supply
voltages higher than 7.0V (absolute maximum) can
permanently damage the amplifier. Parameters that vary
over supply voltage or temperature are shown in the
Typical Characteristics section of this data sheet.
The input common-mode range extends from (V−) − 0.2V
to (V+) + 0.2V. For normal operation, inputs should be
limited to this range. The absolute maximum input voltage
is 500mV beyond the supplies. Inputs greater than the
input common-mode range but less than the maximum
input voltage, while not valid, will not cause any damage
to the op amp. Unlike some other op amps, if input current
is limited, the inputs may go beyond the supplies without
phase inversion, as shown in Figure 2.
G = +1V/V, VS = 5V
VIN
The input common-mode voltage range of the OPA373
and OPA374 series extends 200mV beyond the supply
rails. This is achieved with a complementary input
stage—an N-channel input differential pair in parallel with
a P-channel differential pair. The N-channel pair is active
for input voltages close to the positive rail, typically
(V+) − 1.65V to 200mV above the positive supply, while
the P-channel pair is on for inputs from 200mV below the
negative supply to approximately (V+) − 1.65V. There is a
500mV transition region, typically (V+) − 1.9V to
(V+) − 1.4V, in which both pairs are on. This 500mV
transition region, shown in Figure 1, can vary ±300mV with
process variation. Thus, the transition region (both stages
on) can range from (V+) − 2.2V to (V+) − 1.7V on the low
end, up to (V+) − 1.6V to (V+) − 1.1V on the high end.
Within the 500mV transition region PSRR, CMRR, offset
voltage, offset drift, and THD may be degraded compared
to operation outside this region.
5V
VOUT
1V/div
COMMON-MODE VOLTAGE RANGE
0V
1µs/div
Figure 2. OPA373: No Phase Inversion with
Inputs Greater Than the Power-Supply Voltage
Normally, input bias current is approximately 500fA;
however, input voltages exceeding the power supplies by
more than 500mV can cause excessive current to flow in
or out of the input pins. Momentary voltages greater than
500mV beyond the power supply can be tolerated if the
current on the input pins is limited to 10mA. This is easily
accomplished with an input resistor; see Figure 3. (Many
input signals are inherently current-limited to less than
10mA, therefore, a limiting resistor is not required.)
9
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
V+
IOVERLOAD
10mA max
R
OPA373
VOUT
capacitor, CFB, can be inserted in the feedback, as shown
in Figure 5. This significantly reduces overshoot by
compensating the effect of capacitance, CIN, which
includes the amplifier input capacitance and printed circuit
board (PCP) parasitic capacitance.
VIN
V+
RS
10Ωto 20Ω
Figure 3. Input Current Protection for Voltages
Exceeding the Supply Voltage
VOUT
OPA373
VIN
RL
CL
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors
is used to achieve rail-to-rail output. For light resistive
loads ( > 100kΩ), the output voltage can typically swing to
within 18mV from the supply rails. With moderate resistive
loads (5kΩ to 50kΩ), the output can typically swing to
within 100mV from the supply rails and maintain high
open-loop gain. See the Typical Characteristic curve,
Output Voltage Swing vs Output Current, for more
information.
Figure 4. Series Resistor in Unity-Gain
Configuration Improves Capacitive Load Drive
CFB
RF
CAPACITIVE LOAD AND STABILITY
One method of improving capacitive load drive in the
unity-gain configuration is to insert a small (10Ω to 20Ω)
resistor, RS, in series with the output, as shown in Figure 4.
This significantly reduces ringing while maintaining dc
performance for purely capacitive loads. When there is a
resistive load in parallel with the capacitive load, RS must
be placed within the feedback loop as shown to allow the
feedback loop to compensate for the voltage divider
created by RS and RL.
RI
VIN
VOUT
OPA373
CIN
CL
Figure 5. Improving Capacitive Load Drive
For example, when driving a 100pF load in unity-gain
inverter configuration, adding a 6pF capacitor in parallel
with the 10kΩ feedback resistor decreases overshoot from
57% to 12%, as shown in Figure 6.
60
G = −1V/V
RFB = 10kΩ
50
Overshoot (%)
OPA373 series op amps can drive a wide range of
capacitive loads. However, under certain conditions, all op
amps may become unstable. Op amp configuration, gain,
and load value are just a few of the factors to consider
when determining stability. An op amp in unity-gain
configuration is the most susceptible to the effects of
capacitive load. The capacitive load reacts with the op amp
output resistance, along with any additional load
resistance, to create a pole in the small-signal response
that degrades the phase margin. The OPA373 series op
amps perform well in unity-gain configuration, with a pure
capacitive load up to approximately 250pF. Increased
gains allow the amplifier to drive more capacitance. See
the Typical Characteristics curve, Small-Signal Overshoot
vs Capacitive Load, for further details.
V+
40
30
20
10
In unity-gain inverter configuration, phase margin can be
reduced by the reaction between the capacitance at the op
amp input and the gain setting resistors, thus degrading
capacitive load drive. Best performance is achieved by
using small valued resistors. However, when large valued
resistors cannot be avoided, a small (4pF to 6pF)
10
CFB = 6pF
0
10
100
1k
10k
Load Capacitance (pF)
Figure 6. Improving Capacitive Load Drive
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
DRIVING ADCs
Figure 8 shows the OPA373 driving the ADS7816 in a
speech band-pass filtered data acquisition system. This
small, low-cost solution provides the necessary
amplification and signal conditioning to interface directly
with an electret microphone. This circuit will operate with
VS = 2.7V to 5V.
The OPA373 and OPA374 series op amps are optimized
for driving medium-speed sampling ADCs. The OPA373
and OPA374 op amps buffer the ADC input capacitance
and resulting charge injection, while providing signal gain.
The OPA373 is shown driving the ADS7816 in a basic
noninverting configuration, as shown in Figure 7. The
ADS7816 is a 12-bit, MicroPower sampling converter in
the MSOP-8 package. When used with the low-power,
miniature packages of the OPA373, the combination is
ideal for space-limited, low-power applications. In this
configuration, an RC network at the ADC input can be used
to provide anti-aliasing filtering.
The OPA373 is shown in the inverting configuration
described in Figure 9. In this configuration, filtering may be
accomplished with the capacitor across the feedback
resistor.
ENABLE/SHUTDOWN
OPA373 and OPA374 series op amps typically require
585µA quiescent current. The enable/shutdown feature of
the OPA373 allows the op amp to be shut off in order to
reduce this current to less than 1µA.
+5V
0.1µF
0.1µF
1 VREF
8 V+
500Ω
7
DCLOCK
+In
OPA373
2
VIN
ADS7816
12−Bit ADC
−In
3300pF
6
DOUT
CS/SHDN
3
Serial
Interface
5
GND 4
VIN = 0V to 5V for
0V to 5V output.
fSAMPLE = 100kHz
NOTE: ADC Input = 0 to VREF
RC network filters high frequency noise.
Figure 7. The OPA373 in Noninverting Configuration Driving the ADS7816
V+ = +2.7V to +5V
Passband 300Hz to 3kHz
R9
510kΩ
R1
1.5kΩ
R2
1MΩ
R4
20kΩ
C3
33pF
C1
1000pF
Electret
Microphone (1)
R3
1MΩ
1/2
OPA2373
R7
51kΩ
R8
150kΩ
VREF 1
8 V+
7
C2
1000pF
R6
100kΩ
1/2
OPA2373
+IN
ADS7816 6
12−Bit ADC
5
2
−IN
DCLOCK
D OUT
CS/SHDN
Serial
Interface
3
4 GND
NOTE: (1) Electret microphone
powered by R 1.
R5
20kΩ
G = 100
Figure 8. The OPA2373 as a Speech Bypass Filtered Data Acquisition System
11
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
+5V
330pF
0.1µF
5kΩ
0.1µF
5kΩ
VIN
1 VREF
8 V+
500kΩ
OPA373
VS
2
DCLOCK
7
+IN
6
ADS7816
DOUT
12− Bit ADC
2
5
−IN
CS/SHDN
3300pF
3
GND 4
Serial
Interface
NOTE: ADC Input = 0 to VREF
Figure 9. The OPA373 in Inverting Configuration Driving the ADS7816
C3
330pF
R1
11.7kΩ
1/2
R2
2.72kΩ
R3
21.4kΩ
OPA373
1/2
OPA373
C1
680pF
C2
330pF
NOTE: FilterPro is a low-pass filter design program available for download at
no cost from TI’s web site (www.ti.com). The program can be used to determine
component values for other cutoff frequencies or filter types.
Figure 10. Three-Pole Sallen-Key Butterworth Low-Pass Filter
12
"#"$ %"#"
"#&
%"#&$ &"#&
www.ti.com
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
DFN PACKAGE
LAYOUT GUIDELINES
The OPA2373 is available in a DFN-10 package (also
known as SON), which is a QFN package with lead
contacts on only two sides of the bottom of the package.
This leadless, near-chip-scale package maximizes board
space and enhances thermal and electrical characteristics
through an exposed pad. DFN packages are physically
small, have a smaller routing area, improved thermal
performance, and improved electrical parasitics, with a
pinout scheme that is consistent with other
commonly-used packages, such as SO and MSOP.
Additionally, the absence of external leads eliminates
bent-lead issues.
The leadframe die pad should be soldered to a thermal pad
on the PCB. A mechanical data sheet showing an example
layout is attached at the end of this data sheet.
Refinements to this layout may be required based on
assembly process requirements.
The DFN package can be easily mounted using standard
PCP assembly techniques. See Application Note,
QFN/SON PCB Attachment (SLUA271) and Application
Report, Quad Flatpack No-Lead Logic Packages
(SCBA017), both available for download at www.ti.com.
Mechanical drawings located at the end of this data sheet
list the physical dimensions for the package and pad. The
five holes in the landing pattern are optional, and are
intended for use with thermal vias that connect the
leadframe die pad to the heatsink area on the PCB.
Soldering the exposed pad significantly improves
board-level reliability during temperature cycling, key
push, package shear, and similar board-level tests.
Even with applications that have low-power dissipation,
the exposed pad must be soldered to the PCB to provide
structural integrity and long-term reliability.
The exposed leadframe die pad on the bottom of the
package should be connected to V−.
13
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
OPA2373AIDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 85
AYO
OPA2373AIDGSRG4
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 85
AYO
OPA2373AIDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 85
AYO
OPA2373AIDGSTG4
ACTIVE
VSSOP
DGS
10
250
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 85
AYO
OPA2373AIDRCR
ACTIVE
SON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OCEQ
OPA2373AIDRCRG4
ACTIVE
SON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OCEQ
OPA2373AIDRCT
ACTIVE
SON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OCEQ
OPA2373AIDRCTG4
ACTIVE
SON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OCEQ
OPA2374AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
2374A
OPA2374AIDCNR
ACTIVE
SOT-23
DCN
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ATP
OPA2374AIDCNRG4
ACTIVE
SOT-23
DCN
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ATP
OPA2374AIDCNT
ACTIVE
SOT-23
DCN
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ATP
OPA2374AIDCNTG4
ACTIVE
SOT-23
DCN
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ATP
OPA2374AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
2374A
OPA2374AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA
2374A
OPA2374AIDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA
2374A
OPA373AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Addendum-Page 1
-40 to 125
OPA
373A
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
OPA373AIDBVR
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A75
OPA373AIDBVRG4
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A75
OPA373AIDBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A75
OPA373AIDBVTG4
ACTIVE
SOT-23
DBV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A75
OPA373AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
373A
OPA373AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
373A
OPA373AIDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
373A
OPA374AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
374A
OPA374AIDBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A76
OPA374AIDBVRG4
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A76
OPA374AIDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A76
OPA374AIDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
A76
OPA374AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
374A
OPA374AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
374A
OPA374AIDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
374A
OPA4374AID
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA4374A
OPA4374AIDG4
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA4374A
OPA4374AIDR
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA4374A
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
11-Apr-2013
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
OPA4374AIDRG4
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA4374A
OPA4374AIPWR
ACTIVE
TSSOP
PW
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
4374A
OPA4374AIPWRG4
ACTIVE
TSSOP
PW
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
4374A
OPA4374AIPWT
ACTIVE
TSSOP
PW
14
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
4374A
OPA4374AIPWTG4
ACTIVE
TSSOP
PW
14
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
OPA
4374A
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
OPA2373AIDGSR
VSSOP
DGS
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
OPA2373AIDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
OPA2373AIDRCR
SON
DRC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
OPA2373AIDRCT
SON
DRC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
OPA2374AIDCNR
SOT-23
DCN
8
3000
180.0
8.4
3.2
3.1
1.39
4.0
8.0
Q3
OPA2374AIDCNT
SOT-23
DCN
8
250
180.0
8.4
3.2
3.1
1.39
4.0
8.0
Q3
OPA2374AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
OPA373AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
OPA374AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
OPA4374AIDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
OPA4374AIPWR
TSSOP
PW
14
2500
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
OPA4374AIPWT
TSSOP
PW
14
250
180.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA2373AIDGSR
VSSOP
DGS
10
2500
367.0
367.0
35.0
OPA2373AIDGST
VSSOP
DGS
10
250
210.0
185.0
35.0
OPA2373AIDRCR
SON
DRC
10
3000
367.0
367.0
35.0
OPA2373AIDRCT
SON
DRC
10
250
210.0
185.0
35.0
OPA2374AIDCNR
SOT-23
DCN
8
3000
210.0
185.0
35.0
OPA2374AIDCNT
SOT-23
DCN
8
250
210.0
185.0
35.0
OPA2374AIDR
SOIC
D
8
2500
367.0
367.0
35.0
OPA373AIDR
SOIC
D
8
2500
367.0
367.0
35.0
OPA374AIDR
SOIC
D
8
2500
367.0
367.0
35.0
OPA4374AIDR
SOIC
D
14
2500
367.0
367.0
38.0
OPA4374AIPWR
TSSOP
PW
14
2500
367.0
367.0
35.0
OPA4374AIPWT
TSSOP
PW
14
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages