Finisar Productt Specificaation Multiprotoccol, 80km m, 10Gb/ss DWDM M XFP Op ptical Trransceiver FTLX X3813M33xx PROD DUCT FEA ATURES • Supports 8.5G Gb/s to 11.32 2Gb/s • Hot-pluggabl H le XFP footp print • TemperatureT -stabilized DWDM D EML L trransmitter • RoHS-6 R Com mpliant (lead--free) • 100GHz ITU Grid, C-Ban nd • Duplex D LC co onnector • Power dissipaation <3.5W W • Built-in B digitaal diagnosticc functions • • APPL LICATIONS S • IT TU G.698.1, D DW100S-2Dxx, 10Gb/s DW WDM SO ONET/SDH Temperature T range: 0°C to t 70°C • IE EEE 10GBASE E-ZR based D DWDM Etherrnet Point-to-Poin nt & OSNR optimized o versions • 100GFC (SM-12200-LL-L), 88GFC (SM-8000LC C-L), and 10G G CPRI • IT TU G.709, OT TN/FEC appliications includding IE EEE OTU1e aand OTU2e Finisar’s FTLX3813 3M3xx Smaall Form Faactor 10Gb/ss (XFP) traansceiver coomplies withh the X Multi-S Source Agreeement (MS SA) Specificcation, INF--8077i (rev 4.5). It suppports current XFP multiple protocols for point-to o-point and d amplified 10Gb/s D DWDM appllications with a maximum m link length h of 80km. This T multi-raate, DWDM XFP transceeiver supporrts clock andd data recovery for 8G Fibrre Channel, 10G Fibre Channel, 100G CPRI, 100Gb/s SONE ET/SDH, 100Gb/s Ethernet,, and OTN/F FEC protoco ols up to 11.32Gb/s. Diigital diagnoostics functioons are avaiilable via a 2-w wire serial in nterface, as specified in the XFP M MSA. The traansceiver is RoHS comppliant 3 and lead free per Directive 2002//95/EC , and d Finisar Appplication Noote AN-203884. PROD DUCT SE ELECTIO ON FTL LX3813M M3xx xx: 100GHzz ITU channnel number © Finiisar Corporatio on 19-March-2 2013 Rev. D1 Pagee 1 FTLX3813M3xx DWDM XFP Product Specification – March 2013 Finisar Part Numbers for Amplified (OSNR optimized) Applications: Channel # 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 Product Code FTLX3813M317 FTLX3813M318 FTLX3813M319 FTLX3813M320 FTLX3813M321 FTLX3813M322 FTLX3813M323 FTLX3813M324 FTLX3813M325 FTLX3813M326 FTLX3813M327 FTLX3813M328 FTLX3813M329 FTLX3813M330 FTLX3813M331 FTLX3813M332 FTLX3813M333 FTLX3813M334 FTLX3813M335 FTLX3813M336 FTLX3813M337 FTLX3813M338 FTLX3813M339 FTLX3813M340 FTLX3813M341 FTLX3813M342 FTLX3813M343 FTLX3813M344 FTLX3813M345 FTLX3813M346 FTLX3813M347 FTLX3813M348 FTLX3813M349 FTLX3813M350 FTLX3813M351 FTLX3813M352 FTLX3813M353 FTLX3813M354 FTLX3813M355 FTLX3813M356 FTLX3813M357 FTLX3813M358 FTLX3813M359 FTLX3813M360 FTLX3813M361 © Finisar Corporation 19-March-2013 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 Rev. D1 Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77 Page 2 FTLX3813M3xx DWDM XFP Product Specification – March 2013 Finisar Part Numbers for Point-to-Point (maximum Link Budget) Applications: Channel # 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 Product Code FTLX3813M317P FTLX3813M318P FTLX3813M319P FTLX3813M320P FTLX3813M321P FTLX3813M322P FTLX3813M323P FTLX3813M324P FTLX3813M325P FTLX3813M326P FTLX3813M327P FTLX3813M328P FTLX3813M329P FTLX3813M330P FTLX3813M331P FTLX3813M332P FTLX3813M333P FTLX3813M334P FTLX3813M335P FTLX3813M336P FTLX3813M337P FTLX3813M338P FTLX3813M339P FTLX3813M340P FTLX3813M341P FTLX3813M342P FTLX3813M343P FTLX3813M344P FTLX3813M345P FTLX3813M346P FTLX3813M347P FTLX3813M348P FTLX3813M349P FTLX3813M350P FTLX3813M351P FTLX3813M352P FTLX3813M353P FTLX3813M354P FTLX3813M355P FTLX3813M356P FTLX3813M357P FTLX3813M358P FTLX3813M359P FTLX3813M360P FTLX3813M361P © Finisar Corporation 19-March-2013 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 Rev. D1 Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77 Page 3 FTLX3813M3xx DWDM XFP Product Specification – March 2013 I. Finisar Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 29 30 CML-O CML-O CML-I CML-I GND GND TDTD+ GND Name/Description Module Ground Optional –5.2 Power Supply – Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply – Not required Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply – Not required Module Ground Reference Clock non-inverted input, AC coupled on the host board – Not required Reference Clock inverted input, AC coupled on the host board – Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 1 1 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k – 10kohms on host board to a voltage between 3.15V and 3.6V. © Finisar Corporation 19-March-2013 Rev. D1 Page 4 Finisar FTLX X3813M3xx DW WDM XFP Pro oduct Specificaation – March 22013 Diagram of Hosst Board Conn nector Block P Pin Numbers and Names II. Absolute Maximum Ratings Parameeter Maxim mum Supply Voltage V #1 Maxim mum Supply Voltage V #2 Storag ge Temperaturee Case Operating O Tem mperature Receiv ver Damage Th hreshold © Finiisar Corporatio on 19-March-2 2013 Symbol Vcc3 Vcc5 TS TOP PRdmg Min -0.5 -0.5 -40 0 +5 Rev. D1 Typ Max 4.0 6.0 85 70 Unit V V °C °C dBm Reff. Pagee 5 Finisar FTLX3813M3xx DWDM XFP Product Specification – March 2013 III. Electrical Characteristics (TOP = 0 to 70 °C, VCC5 = 4.75 to 5.25 Volts) Parameter Supply Voltage #1 Supply Voltage #2 Supply Current – Vcc5 supply Supply Current – Vcc3 supply Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc5 Vcc3 Icc5 Icc3 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 4.75 3.13 Typ Max 5.25 3.46 350 750 3.5 Unit V V mA mA W Ω mV V V us 2 820 Vcc GND+ 0.8 10 mV ps ps V V 4 5 5 6 6 7 100 120 2.0 GND 340 Vcc – 0.5 GND 850 38 38 VccHOST GND+0.5 See Note 6 below Ref. 1 3 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 – 80 % 6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1. © Finisar Corporation 19-March-2013 Rev. D1 Page 6 Finisar FTLX3813M3xx DWDM XFP Product Specification – March 2013 IV. Optical Characteristics (EOL, TOP = 0 to 70°C, VCC5 = 4.75 to 5.25 Volts) Transmitter Parameter Output Opt. Pwr: 9/125 SMF Optical Extinction Ratio Center Wavelength Spacing Transmitter Center Wavelength – End Of Life Transmitter Center Wavelength – Beginning Of Life Sidemode Suppression ratio Tx Jitter (SONET) 20kHz-80MHz Tx Jitter (SONET) 4MHz-80MHz Symbol POUT ER Min -1 8.2 Typ λc X-100 100 X λc X-25 X SSRmin Txj1 Txj2 30 Relative Intensity Noise RIN Receiver Maximum Input Power PMAX -7 Optical Center Wavelength 1260 λC Receiver Reflectance Rrx LOS De-Assert LOSD LOS Assert LOSA -37 LOS Hysteresis 0.5 Receiver Sensitivity (FTLX3813M3xx & FTLX3813M3xxP) Sensitivity back-toData rate BER Dispersion (ps/nm) back at OSNR>30dB (Gb/s) (dBm) 8.5 1e-12 -500 to 1450 9.95 1e-12 -500 to 1450 10.3 1e-12 -500 to 1450 10.7 1e-4 -500 to 1300 11.1 1e-4 -500 to 1300 11.3 1e-4 -500 to 1100 OSNR Performance (FTLX3813M3xx ONLY) Data rate (Gb/s) BER Dispersion (ps/nm) -24 -24 -24 -27 -27 -27 Max +3 Ref. X+100 Unit dBm dB GHz pm X+25 pm 2 0.3 0.1 dB UI UI -130 dB/Hz 1600 -27 -30 1 2 dBm nm dB dBm dBm dB Power Penalty at OSNR>30dB (dB) 3 Threshold Adjust. Required 3 3 3 3 3 3 No No No Yes Yes Yes Max OSNR w/ dispersion at Power: -7 to -18dBm (dB) 4 Threshold Adjust. Required 8.5 1e-12 -500 to 1450 28 No 9.95 1e-12 -500 to 1450 28 No 10.3 1e-12 -500 to 1450 28 No 10.7 1e-4 -500 to 1300 22 Yes 11.1 1e-4 -500 to 1300 22 Yes 11.3 1e-4 -500 to 1100 22 Yes Notes: 1. Corresponds to approximately 0.8 nm. 2. X = Specified ITU Grid wavelength. Wavelength stability is achieved within 10 seconds of power up. 3. Measured at 1528-1600nm with worst ER; BER<10-12; PRBS31. 4. All OSNR measurements are performed with 0.1nm resolution over specific Rx_power range © Finisar Corporation 19-March-2013 Rev. D1 Page 7 Finisar FTLX3813M3xx DWDM XFP Product Specification – March 2013 V. General Specifications Parameter Bit Rate Max. Supported Link Length Symbol BR LMAX Min 8.5 Typ Max 11.32 80 Units Gb/s km Ref. 1 Notes: 1. SONET/SDH OC-192, 10G Ethernet, SONET OC-192 with FEC, 10G Ethernet with FEC (OTU1e & OTU2e), 10GFC, 8GFC, and 10G CPRI VI. Environmental Specifications Finisar XFP transceivers have an operating temperature range from 0°C to +70°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units °C °C Ref. Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TÜV Electrical Safety Electrical Safety TÜV EN 60825-1: 2007, EN60825-2:2004+A1 IEC 60825-1: 2007 (2nd Edition) IEC 60825-2: 2010 (3rd Edition) EN 60950:2006+All UL/CSA CLASS 3862.07 CLASS 3862.87 Certificate Number 9210176-77 R72101686 R72101686 2283290 Copies of the referenced certificates are available at Finisar Corporation upon request. © Finisar Corporation 19-March-2013 Rev. D1 Page 8 FTLX3813M3xx DWDM XFP Product Specification – March 2013 Finisar VIII. Digital Diagnostics Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: • • • • • • Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage TEC Temperature It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information, including memory map definitions, please see the XFP MSA documentation1. Receiver Threshold Adjustment The FTLX3813M3xx also provides access to receiver decision threshold adjustment via 2-wire serial interface, in order to improve receiver OSNR performance based on specific link conditions. It is implemented as follows: • • Rx Threshold of XFP transceivers will be factory-set for optimized performance in non-FEC applications. This will be the default value during both cold start (power-up) and warm start (module reset). The transceiver supports adjustment of Rx Threshold value by the host through register 76d, table 01h. This is intended to be used in FEC applications. © Finisar Corporation 19-March-2013 Rev. D1 Page 9 FTLX X3813M3xx DW WDM XFP Pro oduct Specificaation – March 22013 • • Finisar Register 76d, 7 table 01 1h is a volatiile memory. Therefore iff the transceiver is power-cycled, the reg gister starts up u with a vallue of 00h w which correspponds to the default Rx x Threshold value. The thresh hold adjustm ment input vaalue is 2’s coomplement 7 bit value (--128 to +127), wiith 0 corresp ponding to deefault Rx thrreshold value. Full rangee of adjustmen nt provides at a least a ±10 0% change inn Rx threshoold from thee default value. Channel ratee select: 8.5Gb/s Fibre-C To op perate the FT TLX3813M3 3xx at 8.5Gb b/s Fibre-Chhannel, the E EEPROM-Taable 0, Byte 117, Bit B 0 must be b set as follo ows; • EEPROM M Byte 117, Bit B 0, value “1” for 8GF FC: M Byte 117, Bit B 0 value “0” “ for 10Gbb/s rates: • EEPROM o (Itt is also posssible to bypaass the CDRss with, Byte 111, Bit 0.)) wer cycling the t transceiv ver will returrn the transceeiver to norm mal 10Gb/s By deefault, a pow operaation with th he CDRs actiive. IX. Mechaniccal Specifications Finisar’s XFP traansceivers arre compliant with the dim mensions defined by the XFP Multi-Sourccing Agreem ment (MSA). XF FP Transceiveer (dimensionss are in mm) © Finiisar Corporatio on 19-March-2 2013 Rev. D1 Page 110 FTLX X3813M3xx DW WDM XFP Pro oduct Specificaation – March 22013 X. Finisar PCB Layou ut and Bezeel Recommeendations XFP Host Bo oard Mechaniical Layout (d dimensions aree in mm) © Finiisar Corporatio on 19-March-2 2013 Rev. D1 Page 111 FTLX X3813M3xx DW WDM XFP Pro oduct Specificaation – March 22013 Finisar XF FP Detail Host Board Mech hanical Layoutt (dimensions are in mm) mmended Bezzel Design (dim mensions are iin mm) XFP Recom © Finiisar Corporatio on 19-March-2 2013 Rev. D1 Page 112 FTLX3813M3xx DWDM XFP Product Specification – March 2013 Finisar XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 – August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP Optical Transceivers” – Finisar Corporation, December 2003 3. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. January 27, 2003. 4. “Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers”, Finisar Corporation, January 21, 2005. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation 19-March-2013 Rev. D1 Page 13