NIC NSPVM330M35V10X8JLBF Solid polymer aluminum electrolytic capacitor Datasheet

Solid Polymer Aluminum Electrolytic Capacitors
NSPVM Series
SUPER LOW ESR, WIDE TEMPERATURE, SURFACE MOUNT, POLARIZED
FEATURES
• ULTRA LOW ESR (TO 13mΩ)
• HIGH RIPPLE CURRENT RATINGS
• REDUCED SIZES (LOW PROFILE)
* NEW *
Low ESR &
High Ripple Current
CHARACTERISTICS
Rated Voltage Range
2.5 ~ 35VDC
Capacitance Range
10 ~ 1,200μF
Operating Temperature Range
-55°C ~ +105°C
Capacitance Tolerance
±20% (M)
2.5V ~ 20V = 0.2CV
Maximum Leakage Current
After 2 minutes
25V ~ 35V = 0.5CV
W.V. (Vdc)
2.5
4.0
6.3
10
16
20
25
35
Max. Tan δ at 120Hz/20°C
S.V. (Vdc)
2.9
4.6
7.2
11.5
18
23
28.7
40
Tan δ
0.12 max.
Z-55°C/Z+20°C
<1.15
Low Temperature Stability
Impedance Ratio @ 120Hz
Z+105°C/Z+20°C
<1.25
Duration
All Case Sizes: 2,000 hours
Δ Capacitance
Within ±20% of initial measured value
Load Life Test
Δ Tan δ
Less than 150% of specified value
@ 105°C
Δ ESR
Less than 150% of specified value
Δ LC
Less than specified value
The following specifications shall be satisfied when the capacitors are restored to +20°C after
subjecting them to the DC rated voltage at +60°C, 90% ~ 95% RH for 500 hours.
Appearance
No significant damage
Δ Capacitance
Within ±20% of initial measured value
Damp Heat
Δ Tan δ
Less than 150% of specified value
Δ ESR
Less than 150% of specified value
Δ LC
Less than specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the specified surge
voltage @ +105°C for 30 seconds through a protective resistor (1K ohm) and discharged for 5 minutes,
30 seconds.
Appearance
No significant damage
Surge Voltage
Δ Capacitance
Within ±20% of initial measured value
Δ Tan δ
Less than 150% of specified value
Δ ESR
Less than 150% of specified value
Δ LC
Less than specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% @ +105°C)
PART NUMBER SYSTEM
PEAK REFLOW SOLDERING CODE
Code
L
J
NSPVM 391 M 2.5V 6.3X6 L LB F .
RoHS Compliant
Sn-Bi Finish, 15" Reel
Peak Reflow Temperature: L = +250°C, J = +240°C
Case Size (DφxL)
Working Voltage (Vdc)
Tolerance Code (M=20%)
Capacitance Code: First 2 characters
significant, third character is multiplier
Peak Reflow Temperature
+250°C
+240°C
TERMINATION/PACKAGING CODE
Code
LB
Termination Finish and Reel Size
Sn-Bi Finish, 15" reel
Series
PRECAUTIONS
Please review the notes on correct use, safety and precautions found on
pages T10 & T11 of NIC’s Electrolytic Capacitor catalog.
Also found at www.niccomp.com/precautions
If in doubt or uncertainty, please review your specific application - process
details with NIC’s technical support personnel: [email protected]
NIC COMPONENTS CORP. www.niccomp.com
www.lowESR.com
www.RFpassives.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
www.SMTmagnetics.com
1
Solid Polymer Aluminum Electrolytic Capacitors
NSPVM Series
STANDARD PRODUCT AND CASE SIZE TABLE DφxL (mm)
Part Number
NSPVM181M2.5V5X6LLBF
NSPVM391M2.5V6.3X6LLBF
NSPVM561M2.5V8X7JLBF
NSPVM681M2.5V8X7JLBF
NSPVM122M2.5V10X8JLBF
NSPVM101M4V5X6LLBF
NSPVM151M4V5X6LLBF
NSPVM271M4V6.3X6LLBF
NSPVM331M4V6.3X6LLBF
NSPVM471M4V8X7JLBF
NSPVM561M4V8X7JLBF
NSPVM102M4V10X8JLBF
NSPVM101M6.3V5X6LLBF
NSPVM121M6.3V5X6LLBF
NSPVM221M6.3V6.3X6LLBF
NSPVM331M6.3V8X7JLBF
NSPVM391M6.3V8X7JLBF
NSPVM821M6.3V10X8JLBF
NSPVM470M10V5X6LLBF
NSPVM560M10V5X6LLBF
NSPVM680M10V5X6LLBF
NSPVM121M10V6.3X6LLBF
NSPVM221M10V8X7JLBF
NSPVM271M10V8X7JLBF
NSPVM471M10V10X8JLBF
NSPVM330M16V5X6LLBF
NSPVM390M16V5X6LLBF
NSPVM680M16V6.3X6LLBF
NSPVM101M16V8X7JLBF
NSPVM121M16V8X7JLBF
NSPVM221M16V10X8JLBF
NSPVM220M20V6.3X6LLBF
NSPVM470M20V8X7JLBF
NSPVM820M20V10X8JLBF
NSPVM100M25V6.3X6LLBF
NSPVM220M25V8X7JLBF
NSPVM390M25V10X8JLBF
NSPVM150M35V8X7JLBF
NSPVM330M35V10X8JLBF
Cap. Voltage Case Size Leakage Current
(μF) (VDC)
(DxL)
(μA) after 2 minutes
180
5X6
90
390
6.3X6
195
560
2.5
8X7
280
680
8X7
340
1200
10X8
600
100
5X6
80
150
5X6
120
270
6.3X6
216
330
4.0
6.3X6
264
470
8X7
376
560
8X7
448
1000
10X8
800
100
5X6
126
120
5X6
151
220
6.3X6
277
6.3
330
8X7
415
390
8X7
491
820
10X8
1033
47
5X6
94
56
5X6
112
68
5X6
136
10
120
6.3X6
240
220
8X7
440
270
8X7
540
470
10X8
940
33
5X6
105
39
5X6
124
68
6.3X6
217
16
100
8X7
320
120
8X7
384
220
10X8
704
22
6.3X6
88
47
20
8X7
188
82
10X8
328
10
6.3X6
125
22
25
8X7
275
39
10X8
488
15
8X7
263
35
33
10X8
578
Max. ESR (mΩ)
+20°C/100KHz
21
15
13
13
13
22
22
15
15
14
14
14
24
24
15
14
14
14
28
28
28
25
21
21
19
35
35
28
24
24
22
50
45
40
60
50
45
150
100
Ripple Current Rating
(mA) +105°C/100KHz
2670
3160
3600
3600
4450
2160
2610
3160
3160
3950
3950
4300
2500
2500
3160
3950
3950
4300
2310
2310
2310
2530
3220
3220
3800
2070
2070
2340
3010
3010
3450
1650
2000
2500
1500
1800
2100
1000
1800
Load Life Hours
@+105°C
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
RIPPLE CURRENT FREQUENCY CORRECTION FACTORS
Frequency (Hz)
10μF ~ 1,200μF
100
0.10
1K
0.45
10K
0.50
>100K
1.0
Case Size
5X6
6.3X6
8X7
10X8
Dφ ±0.5
5.0
6.3
8.0
10
+
Dφ
DIMENSIONS (mm)
L max.
6.0
6.0
7.0
8.0
A, B ±0.2
5.3
6.6
8.4
10.4
W
0.5 ~ 0.8
0.5 ~ 0.8
0.5 ~ 0.8
0.7 ~ 1.1
I ref
2.3
2.7
3.0
3.3
P ref
1.5
2.0
3.1
4.7
I
I
-
W
0.3mm max.
A
L
P
B
MARKING
Series
M2E
390
2.5V
2
NIC COMPONENTS CORP. www.niccomp.com
Date Code
2 = year 2012
E = month (A-Jan, B-Feb, C-March, D-April, E-May, etc.)
Capacitance
Voltage
www.lowESR.com
www.RFpassives.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
www.SMTmagnetics.com
Solid Polymer Aluminum Electrolytic Capacitors
+
RECOMMENDED LAND PATTERN DIMENSIONS (mm)
Case Size
5X6
6.3X6
8X7
10X8
A
3.0
3.6
4.0
4.0
B
1.6
1.6
1.6
2.5
NSPVM Series
-
C
1.4
1.9
2.1
4.0
B
A
C
A
SOLDERING TEMPERATURES AND DURATIONS
Diameter
Preheat
(120 sec. max.)
5 ~ 6.3mm
160°C ~ 190°C
8 ~ 10mm
160°C ~ 190°C
Time above
200°C
70 sec. max.
60 sec. max.
70 sec. max.
60 sec. max.
Time above
230°C
50 sec. max.
40 sec. max.
50 sec. max.
40 sec. max.
Peak
Number
Temperature of Reflow Passes1
240°C/5 sec.
2x
250°C/5 sec.
2x
230°C/5 sec.
2x
240°C/5 sec.
2x
1. Two reflow passes are permissible with a cool down to room temperature required between the first
and second pass (more than 1 hour).
2. Some case swelling may occur (~ 0.3mm) which is not an indication that the capacitor performance
has been compromised.
Temperature - Deg. C
RECOMMENDED REFLOW SOLDERING PROFILE
Peak Temperature
(see table above)
250
230
200
Time Above 230°C
(see table above)
150
Time Above 200°C
(see table above)
100
Preheat - 120 seconds max.
(see table for temperature)
50
Time (Seconds)
4 + 0.1
CARRIER DIMENSIONS (mm)
D
±0.1
5.5
7.5
11.5
11.5
P
±0.1
12.0
12.0
12.0
16.0
T
±0.2
6.2
6.2
7.2
8.2
t
max.
0.4
0.4
0.4
0.4
5X6
6.3X6
8X7
10X8
W
±1.0
14.0
18.0
26.0
26.0
+
A
P
Feeding
T
2mm ± 0.5mm
REEL DIMENSIONS (mm)
Case Size
-
B
C
±0.3
12.0
16.0
24.0
24.0
D
B
±0.5
5.7
7.0
8.7
10.7
t
Qty per Reel
15" (380mm)
1,000
1,000
1,000
500
φ13mm ± 0.5mm
φ50mm min.
5X6
6.3X6
8X7
10X8
A
±0.5
5.7
7.0
8.7
10.7
1.75 ±
C
Case Size
1.75 + 0.15
1.5∅
+0.1/1.5φ+0.1/-0
φ21mm ± 0.8mm
W
φ380mm ± 2.0mm
TAPING SPECIFICATIONS (mm)
1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets.
2. Leader tape: Approximately 20cm of cover tape at leader.
3. Connection: Maximum 3 connections (slices) per reel.
NIC COMPONENTS CORP. www.niccomp.com
www.lowESR.com
www.RFpassives.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
www.SMTmagnetics.com
3
Similar pages