Wall DCMSAU1205H-1 1 watt dc/dc power converter Datasheet

DCMSAU1 SERIES
1 Watt DC/DC Power Converters
Rev B
FEATURES
• 1 Watt Output Power
• -40°C to +85°C Operating Temperature
• Single & Dual Outputs
• SMT Package with Industry Standard Pin-out
• High I/O Isolation: 3000VDC
• Qualified for Lead-free Reflow Solder Processes
• High Accuracy of Pin Planarity
• MTBF > 2,000,000 Hours
According to IPC/JEDEC J-STD-020D
• Tape & Reel Packaging Available
• Water-washable process available • Efficiency up to 80%
DESCRIPTION
Size:
0.60 x 0.31 x 0.28 inches
15.3 x 8.0 x 7.1 mm
Weight:
0.08oz (2.2g)
The DCMSAU1 series of DC/DC converters provides 1 Watt of output power in an SMT
package featuring high I/O isolation of 3000VDC. These converters operate over input voltage
ranges of 4.5~5.5VDC, 10.8~13.2VDC, and 21.6~26.4VDC. This series also has single and
dual output voltages of 5V, 12V, 15V, ±5V, ±12V, and ±15V. The DCMSAU1 series’ impressive
efficiencies enable these modules to deliver their fully rated output power from –40°C to +85°C
without a heatsink or forced-air cooling. The very small footprint of these converters makes
them an ideal solution for many applications where a voltage has to be isolated such as for
noise reduction, ground loop elimination in digital interfaces, or where a higher I/O isolation is
required. These converters are also fully qualified for the higher temperature profile used in
lead-free reflow solder processes. These converters can also be supplied in tape & reel
packaging for use in automated SMD production lines.
MODEL SELECTION TABLE
SINGLE OUTPUT MODELS
Model Number
DCMSAU505H-1
DCMSAU512H-1
DCMSAU515H-1
DCMSAU1205H-1
DCMSAU1212H-1
DCMSAU1215H-1
DCMSAU2405H-1
DCMSAU2412H-1
DCMSAU2415H-1
Input Voltage
5 VDC
(4.5 - 5.5 VDC)
12 VDC
(10.8 - 13.2
VDC)
24 VDC
(21.6 - 26.4
VDC)
Output
Voltage
5 VDC
Output Current
Min
Max
4mA
200mA
12 VDC
1.5mA
84mA
15 VDC
1mA
5 VDC
4mA
12 VDC
1.5mA
84mA
15 VDC
1mA
5 VDC
4mA
12 VDC
1.5mA
84mA
15 VDC
1mA
67mA
Input Current
Load
No Load Max Load Regulation
281mA
10%
30mA
258mA
7%
67mA
258mA
7%
200mA
117mA
8%
106mA
5%
67mA
104mA
200mA
58mA
12mA
7mA
Output
Maximum
Efficiency
Power
Capacitive Load
1W
71%
33µF
1W
78%
4.7µF
1W
78%
4.7µF
1W
71%
33µF
1W
79%
4.7µF
5%
1W
80%
4.7µF
8%
1W
71%
33µF
53mA
5%
1W
78%
4.7µF
43mA
5%
1W
79%
4.7µF
DUAL OUTPUT MODELS
Model Number
DCMSAU505DH-1
DCMSAU512DH-1
DCMSAU515DH-1
DCMSAU1205DH-1
DCMSAU1212DH-1
DCMSAU1215DH-1
DCMSAU2405DH-1
DCMSAU2412DH-1
DCMSAU2415DH-1
Input Voltage
Output
Voltage
±5 VDC
Output Current
Min
Max
±2mA
±100mA
5 VDC
(4.5 - 5.5 VDC)
±12 VDC
±0.8mA
±42mA
±15 VDC
±0.7mA
±34mA
12 VDC
(10.8 - 13.2
VDC)
±5 VDC
±2mA
±100mA
±12 VDC
±0.8mA
±42mA
±15 VDC
±0.7mA
±34mA
24 VDC
(21.6 - 26.4
VDC)
±5 VDC
±2mA
±100mA
±12 VDC
±0.8mA
±42mA
±15 VDC
±0.7mA
±34mA
Input Current
Load
No Load Max Load Regulation
277mA
10%
30mA
12mA
7mA
Output
Maximum
Efficiency
Power
Capacitive Load
1W
72%
±10µF
255mA
7%
1W
78%
±2.2µF
258mA
7%
1W
79%
±2.2µF
112mA
8%
1W
74%
±10µF
105mA
5%
1W
80%
±2.2µF
104mA
5%
1W
81%
±2.2µF
57mA
8%
1W
72%
±10µF
53mA
5%
1W
79%
±2.2µF
53mA
5%
1W
80%
±2.2µF
NOTES
1. The DCMSAU1 series requires a minimum output loading to maintain specified regulations. Operation under no-load conditions will not
damage these devices; however they may not meet all listed specifications.
2. All DC/DC converters should be externally fused at the front end for protection.
3. Other input and output voltages may be available, please contact factory.
*Due to advances in technology, specifications are subject to change without notice.
10/23/2013
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797
website: www.wallindustries.com • e-mail: [email protected]
Page 1 of 5
Rev B
DCMSAU1 SERIES
1 Watt DC/DC Power Converters
SPECIFICATIONS: DCMSAU1 SERIES
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
TEST CONDITIONS
Min
Typ
4.5
10.8
21.6
-0.7
-0.7
-0.7
5
12
24
Max
Unit
INPUT SPECIFICATIONS
Input Voltage Range
Input Surge Voltage (1sec, max.)
5VDC nominal input models
12VDC nominal input models
24 VDC nominal input models
5VDC nominal input models
12VDC nominal input models
24 VDC nominal input models
Reverse Polarity Input Current
Input Current
Internal Power Dissipation
Input Filter
5VDC nominal input models
12VDC nominal input models
24 VDC nominal input models
Input Fuse
5.5
13.2
VDC
26.4
9
18
VDC
30
0.3
A
See Table
550
mW
Internal capacitor
500mA slow-blow type
200mA slow-blow type
100mA slow-blow type
OUTPUT SPECIFICATIONS
Output Voltage
Output Voltage Accuracy
Output Voltage Balance (Dual
Outputs)
Line Regulation
Load Regulation
Output Power
Output Current
Minimum Load
Maximum Capacitive Load
Ripple & Noise (20MHz)
See Table
±1.5
±4.0
%
Balanced loads
±0.1
±1.0
%
For Vin change of 1%
20% load to 100% load
±1.2
±1.5
See Table
1
See Table
See Table
See Table
75
100
150
15
±0.01
±0.02
%
See Note 1
Over line, over load, and over temperature
Temperature Coefficient
W
mVp-p
mVp-p
mV rms
%/°C
PROTECTION
Short Circuit Protection
Automatic Recovery
0.5
s
GENERAL SPECIFICATIONS
Efficiency
Switching Frequency
Isolation Voltage (I/P to O/P)
Isolation Resistance (I/P to O/P)
Isolation Capacitance (I/P to O/P)
Nominal input voltage and full load
60 seconds
500VDC
100KHz, 1V
See Table
100
150
50
3000
10
60
KHz
VDC
GΩ
pF
100
ENVIRONMENTAL SPECIFICATIONS
Operating Ambient Temperature
Case Temperature
Storage Temperature
Relative Humidity
Cooling
Lead Temperature
Moisture Sensitivity Level (MSL)
MTBF
See derating curve
-40
+85
+90
+125
95
Free air convection
300
Level 2
-50
Non-condensing
1.5mm from case for 10 sec.
IPC/JEDEC J-STD-020D
MIL-HDBK-217F at 25°C, ground benign
°C
°C
°C
% RH
°C
2,000,000
hours
PHYSICAL SPECIFICATIONS
Weight
Dimensions (L x W x H)
Case Material
10/23/2013
Flammability to UL 94V-0 rated
0.08oz (2.2g)
0.60 x 0.31 x 0.27 inch
(15.3 x 8.0 x 6.75 mm)
Molding
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797
website: www.wallindustries.com • e-mail: [email protected]
Page 2 of 5
Rev B
DCMSAU1 SERIES
1 Watt DC/DC Power Converters
DERATING CURVE
MECHANICAL DRAWING
Mechanical Dimensions
10/23/2013
Connecting Pin Patterns
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797
website: www.wallindustries.com • e-mail: [email protected]
Page 3 of 5
Rev B
DCMSAU1 SERIES
1 Watt DC/DC Power Converters
DESIGN CONSIDERATIONS
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current is measured with an inductor Lin (4.7µH) and Cin (220µF, ESR < 1.0Ω at 100 KHz) to simulate
source impedance. Capacitor Cin offsets possible battery impedance. Current ripple is measured at the input terminals of the
module. Measurement bandwidth is 0-500 KHz.
Peak-to-Peak Output Noise Measurement Test
Use a 0.33µF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 020MHz. Position the load between 50mm and 75mm from the DC/DC converter.
TEST SETUP
Maximum Capacitive Load
The DCMSAU1 series has a limitation of maximum connected capacitance on the output. The power module may be
operated in current limiting mode during start-up, affecting the ramp-up and the start-up time. The maximum capacitance can
be found in the Model Selection Table.
Input Source Impedance
The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect
the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be
necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure
stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 KHz)
capacitor of 2.2µF for 5VDC input models, 1.0µF for 12VDC input models, and 0.47µF for 24VDC input models.
Output Ripple Reduction
A good quality low ESR capacitor placed as close as possible across the load will give the best ripple and noise performance.
To reduce output ripple, it is recommended to use 1.5µF capacitors at the output.
10/23/2013
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797
website: www.wallindustries.com • e-mail: [email protected]
Page 4 of 5
Rev B
DCMSAU1 SERIES
1 Watt DC/DC Power Converters
TEST SETUP
Thermal Considerations
Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module, and board
spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case
temperature must be kept below 90°C. The derating curves are determined from measurements obtained in a test setup.
COMPANY INFORMATION
Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development
engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008
certification is just one example of our commitment to producing a high quality, well-documented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely
with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide
ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your
future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
10/23/2013
(603)778-2300
(888)597-9255
(603)778-9797
[email protected]
www.wallindustries.com
37 Industrial Drive
Exeter, NH 03833
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-7789797
website: www.wallindustries.com • e-mail: [email protected]
Page 5 of 5
Similar pages