Intersil ISL88021IU8HCZ Triple voltage monitor with adjustable power-on-reset and undervoltage/ overvoltage monitoring capability Datasheet

ISL88021, ISL88022
®
Data Sheet
September 18, 2006
Triple Voltage Monitor with Adjustable
Power-On-Reset and Undervoltage/
Overvoltage Monitoring Capability
The ISL88021 and ISL88022 family of devices are
customizable triple voltage-monitoring supervisors that
assert a reset if any of the monitored voltages becomes
non-compliant. They offer popular functions such as
Power-On-Reset timing control with both RESET and
RESET outputs, Supply Voltage Supervision, both under or
overvoltage detection, and Manual Reset assertion. By
offering these features in a small 8 Ld MSOP package, the
ISL88021 and ISL88022 can lower system cost, reduce
board space requirements and increase the reliability of
systems.
Applying a voltage to VDD activates the Power-On-Reset
circuit which holds RESET low for an adjustable period of
time. This allows the power supply and system oscillator to
stabilize before the processor can execute code.
Low VDD detection circuitry protects the user’s system from
low voltage conditions, resetting the system when VDD falls
below its minimum preset voltage threshold VTH1. Reset
remains asserted until VDD returns to its proper operating
level and stabilizes. Two additional voltage monitoring
inputs, V2MON (preset) and V3MON (adjustable), monitor
other supplies to provide reliable system operation.
The ISL88021 V3MON input monitors for undervoltage (UV)
conditions whereas the ISL88022 V3MON input allows
monitoring for overvoltage (OV) conditions. The monitored
voltage on V3MON on either device is compared via a
resistor divider to a 600mV internal reference. Hence, any
voltage more or less positive than this reference can be
accurately monitored to meet specific system level
requirements or to fine-tune the threshold for applications
requiring higher precision.
These devices also let users increase the Power-On-Reset
time-out delay by connecting a capacitor between CPOR and
ground. This lengthens the period of an internal clock
counter thereby increasing the time between voltage
compliance and reset outputs signaling.
FN8226.1
Features
• Triple Voltage Monitor and Reset Assertion
• Low VDD Detection and Reset Assertion
- Adjustable Reset Threshold Voltages
- 0.6V ±6mV Over -40°C to +85°C
- Reset Signal Valid to VDD = 1V
• 140ms Minimum Reset Pulse Delay that is Customizable
Using an External Capacitor
• Both RST and RST Outputs Available
• Undervoltage/Overvoltage Monitoring Capability
• Low 20µA Consumption
• Small 8 Ld MSOP Package
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• Process Control Systems
• Intelligent Instruments
• Embedded Control Systems
• Computer Systems
• Portable/Battery-Powered Equipment
• Multi-Voltage Systems
Pinout
ISL88021, ISL88022
(8 LD MSOP)
TOP VIEW
MR
1
8
RST
VDD
2
7
RST
V2MON
3
6
CPOR
GND
4
5
V3MON
A manual reset input provides debounce circuitry for
minimum reset component count.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL88021, ISL88022
Ordering Information
PART
NUMBER
Ordering Information
(See Notes)
PART
VDD V2MO V3MON
MARKING VTRIP1 VTRIP2 TYPE PACKAGE
PART
NUMBER
(See Notes) (Continued)
PART
VDD V2MO V3MON
MARKING VTRIP1 VTRIP2 TYPE PACKAGE
ISL88021IU8FAZ ANM
3.09V
1.69V
UV
8 Ld MSOP
ISL88022IU8HAZ
4.64V
1.69V
OV
8 Ld MSOP
ISL88021IU8FCZ ANL
3.09V
2.32V
UV
8 Ld MSOP
ISL88022IU8HCZ
4.64V
2.32V
OV
8 Ld MSOP
ISL88021IU8FEZ
3.09V
2.92V
UV
8 Ld MSOP
ISL88022IU8HEZ ANO
4.64V
2.92V
OV
8 Ld MSOP
ISL88021IU8FFZ
3.09V
3.09V
UV
8 Ld MSOP
ISL88022IU8HFZ ANN
4.64V
3.09V
OV
8 Ld MSOP
ISL88021IU8HAZ
4.64V
1.69V
UV
8 Ld MSOP
NOTES:
ISL88021IU8HCZ
4.64V
2.32V
UV
8 Ld MSOP
ISL88021IU8HEZ ANK
4.64V
2.92V
UV
8 Ld MSOP
ISL88021IU8HFZ ANJ
4.64V
3.09V
UV
8 Ld MSOP
ISL88022IU8FAZ ANQ
3.09V
1.69V
OV
8 Ld MSOP
ISL88022IU8FCZ ANP
3.09V
2.32V
OV
8 Ld MSOP
ISL88022IU8FEZ
3.09V
2.92V
OV
8 Ld MSOP
ISL88022IU8FFZ
3.09V
3.09V
OV
8 Ld MSOP
1. Standard versions are shown in bold. For non-standard versions,
please contact factory for availability.
2. Add “-TK” suffix for Tape and Reel.
3. Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
Block Diagrams
VDD
VDD
RST
RST
RST
RST
POR
POR
V2MON
CPOR
V2MON
CPOR
MR
V3MON
MR
V3MON
PB
± VREF
PB
± VREF
GND
GND
ISL88022
ISL88021
Pin Descriptions
ISL88021
ISL88022
NAME
1
1
MR
Active-Low Open Drain Manual Reset Input
2
2
VDD
Power Supply Input
3
3
V2MON
4
4
GND
5
FUNCTION
Second Undervoltage Monitor Input
Ground
V3MON
Undervoltage Monitor Input
5
V3MON
Overvoltage Monitor Input
6
6
CPOR
Set Power-On-Reset Timeout Delay
7
7
RST
Active-Low Open Drain Reset Output
8
8
RST
Active-High Push-Pull Reset Output
2
FN8226.1
September 18, 2006
ISL88021, ISL88022
Absolute Maximum Ratings
Thermal Information
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . -40 C to +85 C
Voltage on Any Pin with Respect to GND . . . . . . . . . . . -1.0V to +7V
D.C. Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .
145
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300°C
(MSOP - Lead Tips Only)
Recommended Operating Conditions
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
SYMBOL
Over the recommended operating conditions unless otherwise specified.
PARAMETER
TEST CONDITIONS
MAX
UNITS
5.5
V
12.5
15
µA
V2MON = 3.3V
5.5
6
µA
V3MON = 1.0V
19
100
nA
VDD
Supply Voltage Range
IDD1
VDD Supply Current
VDD = 5.0V
IDD2
V2MON Input Current
IDDA
V3MON Input Current
MIN
TYP
2.0
VOLTAGE THRESHOLDS
VTH1
VTH1HYST
VTH2
VTH2HYST
VTH3
VREFHYST
Fixed Voltage Trip Point for VDD
Hysteresis of VTH1
Fixed Voltage Trip Point for V2MON
Hysteresis of VTH2
V3MON Threshold Voltage
ISL88021/22IU8HxZ
4.565
4.649
4.733
V
ISL88021/22IU8FxZ
3.029
3.085
3.141
V
VTH1 = 4.64V
46
mV
VTH1 = 3.09V
37
mV
ISL88021/22IU8xFZ
3.034
3.090
3.146
V
ISL88021/22IU8xEZ
2.894
2.947
3.000
V
ISL88021/22IU8xCZ
2.290
2.332
2.374
V
ISL88021/22IU8xAZ
1.660
1.690
1.720
V
VTH2 = 3.09V
37
mV
VTH2 = 2.92V
29
mV
VTH2 = 2.32V
23
mV
VTH2 = 2.19V
22
mV
VTH2 = 1.69V
17
mV
VTH for V3MON on ISL88021
0.594
0.605
0.616
V
VTH for V3MON on ISL88022
0.587
0.595
0.603
V
Hysteresis Voltage
3
mV
RESET
VOL
VOH
Reset Output Voltage Low
RST Output Voltage High
tRPD
VTH to Reset Asserted Delay
tPOR
POR Timeout Delay
CLOAD
Load Capacitance on Reset Pins
3
VDD ≥ 3.3V, Sinking 2.5mA
0.05
0.40
V
VDD < 3.3V, Sinking 1.5mA
0.05
0.40
V
VDD ≥ 3.3V, Sourcing 2.5mA
VDD-0.6
VDD-0.4
V
VDD < 3.3V, Sourcing 1.5mA
VDD-0.6
VDD-0.4
V
10
µs
200
ms
5
pF
CPOR is open
140
FN8226.1
September 18, 2006
ISL88021, ISL88022
Electrical Specifications
SYMBOL
Over the recommended operating conditions unless otherwise specified. (Continued)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
0.8
V
MANUAL RESET
VMRL
MR Input Voltage Low
VMRH
MR Input Voltage High
tMR
MR Minimum Pulse Width
RPU
Internal Pull-Up Resistor
VDD-0.6
V
550
ns
20
kΩ
Functional Description
Power-On-Reset (POR)
The ISL88021 and ISL88022 devices incorporate such features
as Power-On-Reset control, Supply Voltage Supervision,
Undervoltage or Overvoltage Monitoring, and Manual Reset
Assertion.
Applying power to the ISL88021 and ISL88022 devices
activates a POR circuit which holds the RESET pin low once
VDD > 1V. This signal provides several benefits:
The ISL88021 and ISL88022 devices provide common preset
threshold voltages on both VDD and V2MON and for an
optional resistor divider network on V3MON to provide custom
voltage monitoring of voltages greater than 0.6V. An optional
capacitor can be connected between the CPOR pin and GND to
increase the nominal 200ms tPOR delay. Figure 7 illustrates
operational functionality with a timing diagram.
Voltage Monitoring
During normal operation, the ISL88021 and ISL88022 monitor
the voltage levels on VDD, V2MON and V3MON. The
ISL88021 asserts reset if any one of these voltages fall below
their respective voltage trip points and in the case of ISL88022
above the voltage trip point on the V3MON input. The reset
signal effectively prevents the microprocessor from operating
during a power failure, brownout or over voltage condition. This
signal remains active until all monitored voltages meet all
voltage threshold requirements for the reset time delay period
tPOR. Note that both RESET and RESET signals are provided
for design flexibility. Figure 1 illustrates the VDD, V2MON and
V3MON input threshold voltages for the various available
options.
4.500
Vth = 4.64V
• It prevents the processor from operating prior to
stabilization of the oscillator.
• It ensures that the monitored device is held out of operation
until internal registers are properly loaded.
• It allows time for an FPGA to download its configuration prior
to initialization of the circuit.
When all of the monitored voltages meet their respective
input voltage requirements for the specified reset timeout
delay tPOR, the POR circuit simultaneously pulls the RST
output low and releases the RST output to allow the system
to begin operation.
Adjusting tPOR
On the ISL88021 and ISL88022, users can adjust the
Power-On-Reset timeout delay (tPOR) to many times the
nominal tPOR. Figure 2 illustrates the effect of capacitance
on the CPOR pin to ground, showing changing tPOR with a
graph normalized to 175ms for an open CPOR pin. The
maximum recommended capacitance that should be placed
on the CPOR pin is 50pF. NOTE: Care should be taken in
PCB layout and capacitor placement in order to eliminate
stray capacitance as much as possible, which contributes to
tPOR error.
4.000
3.500
Vth = 3.09V
3.000
10
Vth = 2.92V
2.500
2.000
Vth = 2.32V
1.500
Vth = 1.69V
Normalized t POR
VDD, V2MON, V3MON Vth (V)
5.000
• It prevents the system microprocessor from starting to
operate with insufficient voltage.
1.000
0.500
0.000
Vth = 0.60V
-40
25
85
TEMPERATURE (°C)
FIGURE 1. VDD, V2MON, V3MON VTH vs TEMP
8
6
4
2
0
1
5
9 13 17 21 25 29 33 37 41 45
CPOR (pF)
FIGURE 2. NORMALIZED tPOR vs CPOR GRAPH
4
FN8226.1
September 18, 2006
ISL88021, ISL88022
Manual Reset
The manual reset input (MR) allows the user to trigger a reset
by using a push-button switch or by signaling that pin low. The
MR input is an active low debounced input. By connecting a
push-button directly from MR to ground, the designer adds
manual system reset capability. Reset is asserted if the MR pin
is pulled low to less than 100mV for 1µs or longer while the
push-button is closed or a reset is signaled. After MR is
released, the reset outputs remain asserted for tPOR. MR input
has an internal 20kΩ pull up resistor provided.
ISL88021IU8HFZ
Figure 3 illustrates a typical application diagram for either IC
showing both reset outputs being used along with both a
manual and signalled reset configuration. The VDD and
V2MON thresholds are preset whereas the V3MON is capable
of UV (ISL88021) or OV (ISL88022) monitoring of a voltage
greater than or less than 0.6V, respectively.
TO DISPLAY
3.3V - 5V
VDD
TO µP
RST
RST
ISL88022IU8HFZ
V2MON
MR
1.8V - 3.3V
ISL88021
ISL88022
RESET
SIGNAL
CPOR
V3MON
VMON > 0.6V
PB
GND
FIGURE 3. TYPICAL APPLICATION DIAGRAM
Application Considerations
Follow good decoupling practices to prevent transients from
causing unwanted reset signaling due to switching noises
and short duration droops.
When using the CPOR pin, reduce layout stray capacitance
on this pin to minimize effect on tPOR timing. If no PCB
CPOR pad is patterned, the tPOR can be 160ms.
FIGURE 4. ISL88021_22EVAL1 SCHEMATIC AND PHOTO
MONITORED VOLTAGE RISING AND FALLING RAMP
THROUGH THE PROGRAMMED UV AND OV THRESHOLDS
Using the ISL88021_22EVAL1 Platform
The ISL88021_22EVAL1 board is designed to provide both
immediate functional assessment and flexibility to the user.
Both ICs are the ‘HF’ variant having a VDD Vth of 4.64V, a
V2MON Vth of 3.09V and V3MON Vth of 0.6V. The top IC
position is the ISL88021 and is configured to monitor for
undervoltage (UV) compliance of a 5V, 3.3V and a 2.5V and
signaling the RESET and RESET outputs. The bottom
position is the ISL88022 variant, which is configured to
measure a 3.3V overvoltage (OV) in addition to UV on both
the 5V and 3.3V supplies. RESET and RESET is asserted for
at least tPOR when these voltage go out of range. In both
cases V3MON interfaces with the monitored supply via a
simple resistor divider for comparison to the internal 0.6V
reference. A Manual Reset (MR) input is provided on both
ICs and is invoked by pulling this input LOW.
5
RESET# RESPONDING TO
MONITORED VOLTAGE. CPOR
PIN IS OPEN, tPOR = 150ms
FIGURE 5. ISL88022EVAL1 3.3V UV AND OV DETECTION
FN8226.1
September 18, 2006
ISL88021, ISL88022
3.3V RISING EDGE 100ms/DIV
ISL88022 tPOR = 150ms
CPOR = OPEN
ISL88021 tPOR = 390ms
CPOR = 10pF
FIGURE 6. ISL88021_22EVAL1 tPOR COMPARISON
Operational Timing Diagrams
VTH1
VDD
1V
V2MON or V3MON
(ISL88021)
VTH2 or VREF
>tMR
MR
tPOR
tRPD
tPOR
tRPD
tPOR
tPOR
RST
RST
<tMD
FIGURE 7. ISL88021 AND ISL88022 TIMING DIAGRAM
6
FN8226.1
September 18, 2006
ISL88021, ISL88022
Mini Small Outline Plastic Packages (MSOP)
N
M8.118 (JEDEC MO-187AA)
8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
E1
INCHES
E
-B-
INDEX
AREA
1 2
0.20 (0.008)
A B C
TOP VIEW
4X θ
0.25
(0.010)
R1
R
GAUGE
PLANE
A
SEATING
PLANE -C-
A2
A1
b
-He
D
0.10 (0.004)
4X θ
L1
SEATING
PLANE
C
0.20 (0.008)
C
a
CL
E1
C D
MAX
MIN
MAX
NOTES
0.037
0.043
0.94
1.10
-
A1
0.002
0.006
0.05
0.15
-
A2
0.030
0.037
0.75
0.95
-
b
0.010
0.014
0.25
0.36
9
c
0.004
0.008
0.09
0.20
-
D
0.116
0.120
2.95
3.05
3
E1
0.116
0.120
2.95
3.05
4
0.026 BSC
0.65 BSC
-
E
0.187
0.199
4.75
5.05
-
L
0.016
0.028
0.40
0.70
6
0.037 REF
N
C
0.20 (0.008)
MIN
A
L1
-A-
SIDE VIEW
SYMBOL
e
L
MILLIMETERS
0.95 REF
8
R
0.003
R1
0
α
-
8
-
0.07
0.003
-
5o
15o
0o
6o
7
-
-
0.07
-
-
5o
15o
-
0o
6o
-B-
Rev. 2 01/03
END VIEW
NOTES:
1. These package dimensions are within allowable dimensions of
JEDEC MO-187BA.
2. Dimensioning and tolerancing per ANSI Y14.5M-1994.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs and are measured at Datum Plane. Mold flash, protrusion
and gate burrs shall not exceed 0.15mm (0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions
and are measured at Datum Plane. - H - Interlead flash and
protrusions shall not exceed 0.15mm (0.006 inch) per side.
5. Formed leads shall be planar with respect to one another within
0.10mm (0.004) at seating Plane.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable
dambar protrusion shall be 0.08mm (0.003 inch) total in excess
of “b” dimension at maximum material condition. Minimum space
between protrusion and adjacent lead is 0.07mm (0.0027 inch).
10. Datums -A -H- .
and - B - to be determined at Datum plane
11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
7
FN8226.1
September 18, 2006
Similar pages