ETC2 APSDM008GB5AN-ACMW Sata-disk module 4 Datasheet

RoHS Compliant
SATA-Disk Module 4
SDM4-M 7P/180D Low Profile Specifications
April 6th, 2012
Version 1.2
Apacer Technology Inc.
th
4 Fl., 75 Hsin Tai Wu Rd., Sec.1, Hsichih, New Taipei City, Taiwan 221
Tel: +886-2-2698-2888
www.apacer.com
Fax: +886-2-2698-2889
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
Features:

Standard Serial ATA 2.6 (Gen. 2)
– Serial ATA 2.6 (Gen. 2)
– SATA II, 3.0 Gbps
– ATA-compatible command set

Capacities
– 4, 8, 16, 32 GB

Performance*
– Burst read/write: 300 MB/sec
– Sustained read: up to 43 MB/sec
– Sustained write: up to 21 MB/sec

Intelligent endurance design
– Built-in hardware ECC, enabling up to
16/24 bit correction per 1K bytes
– Static wear-leveling scheme together
with dynamical block allocation to
significantly increase the lifetime of a
flash device and optimize the disk
performance
– Flash bad-block management
– S.M.A.R.T.
– Power Failure Management
– ATA Secure Erase
– TRIM

NAND Flash Type: MLC

MTBF: >1,000,000

Zero power data retention
– No battery required for data storage

Temperature ranges
– Operation:
Standard: 0°C to 70°C
Extended: -40 ~ +85°C ***
– Storage: -40°C to 100°C

Supply voltage
– 5.0 V ± 5%

Power consumption (typical)*
– Active mode: 185 [email protected] V
– Idle mode: 85 [email protected] V

Connector type
– 7-pin signal connector
– Option : 2-pin additional power connector

Form factor
– SATA Disk Module
– Dimension (w/o housing):
30.00x20.00x1.00**, unit: mm
– Dimension (w/ housing): 32.50
x23.30x8.53**, unit: mm

Shock & Vibration
– Shock: 50g (approx.)
– Vibration: 15g (approx.)

RoHS compliant
*Varies from capacities. The values for performances and power consumptions presented are typical and may vary depending on
flash configurations or platform settings. The term idle refers to the standby state of the device.
**Without including the size of SATA connector
***Only available in 4, 8, 16GB capacities. Please see “Product Ordering Information” for details.
1
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
Table of Contents
1. GENERAL DESCRIPTION .................................................................................................3
1.1 PERFORMANCE-OPTIMIZED CONTROLLER ....................................................................................................... 3
1.1.1 Power Management Unit (PMU) ............................................................................................................ 3
1.1.2 SRAM Buffer .......................................................................................................................................... 3
2. FUNCTIONAL BLOCK .......................................................................................................4
3. PIN ASSIGNMENTS ............................................................................................................5
4. CAPACITY SPECIFICATION............................................................................................7
4.1 PERFORMANCE SPECIFICATION ....................................................................................................................... 7
4.1.1 ATA Mode Support ................................................................................................................................. 7
4.1.2 Performance .......................................................................................................................................... 7
4.2 ENVIRONMENTAL SPECIFICATIONS ................................................................................................................. 8
4.3 MEAN TIME BETWEEN FAILURES (MTBF)...................................................................................................... 8
4.4 CERTIFICATION AND COMPLIANCE ................................................................................................................. 8
5. FLASH MANAGEMENT....................................................................................................9
5.1 ERROR CORRECTION/DETECTION ................................................................................................................... 9
5.2 BAD BLOCK MANAGEMENT ........................................................................................................................... 9
5.3 WEAR LEVELING ........................................................................................................................................... 9
5.4 POWER FAILURE MANAGEMENT ..................................................................................................................... 9
5.5 ATA SECURE ERASE...................................................................................................................................... 9
5.6 S.M.A.R.T. ................................................................................................................................................. 10
5.7 TRIM ......................................................................................................................................................... 10
6. SOFTWARE INTERFACE ...............................................................................................11
6.1 COMMAND SET ............................................................................................................................................ 11
7. ELECTRICAL SPECIFICATION....................................................................................12
7.1 ELECTROSTATIC DISCHARGE ....................................................................................................................... 12
7.2 ELECTRICAL FAST TRANSIENT/BURST .......................................................................................................... 13
8. PHYSICAL CHARACTERISTICS ..................................................................................14
8.1 POWER CABLE TYPE .................................................................................................................................... 14
8.1.1 W/o Housing ....................................................................................................................................... 14
8.1.2 W/ Housing.......................................................................................................................................... 15
8.2 POWER CABLE-LESS TYPE ............................................................................................................................ 16
8.2.1 W/o Housing ........................................................................................................................................ 16
8.2.2 W/ Housing.......................................................................................................................................... 17
9. PRODUCT ORDERING INFORMATION ......................................................................18
9.1 PRODUCT CODE DESIGNATIONS ................................................................................................................... 18
2
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
1. General Description
Apacer’s SATA-Disk Module 4-M (SDM4-M) is a high-performance, embedded SSD designed to replace
the conventional SATA hard disk drive. SDM SSD can be plugged into a standard Serial ATA 7-pin
connector commonly found in desktops, IT-STB, industrial PC and thin client systems. Moreover, Apacer
provides an innovative way for design-in customers to strengthen the vibration-resistance between
SDM4-M and mainboard. Though built with MLC, this SSD can work in highly demanding
environment as it can withstand ambient temperature from -40°C to +85°C (for certain capacities
only).
Apacer’s SDM4-M has a built-in microcontroller with file management firmware that communicates with
SATA standard interface. This means SDM4-M does not require additional or proprietary host software
such as Flash File System (FFS) and Memory Technology Driver (MTD). This product is well suited for
embedded flash storage applications offering new and expanded functionalities as well as more costeffective designs, better performance and increased reliability.
SDM4-M Series is designed to work at 5 Volts and uses a standard SATA driver that complies with major
operating systems such as Microsoft’s Windows series.
Featuring technologies as Apacer-specific Wear-leveling algorithms, S.M.A.R.T, Enhanced Data Integrity,
Intelligent Power Failure Management, ATA Secure Erase, and TRIM, Apacer assures users of a versatile
device on data storage.
1.1 Performance-Optimized Controller
The heart of SDM4-M is the Flash controller, which translates standard SATA signals into the data and
controls of the flash media. The SATA and Flash Management controller are specifically designed to
attain high data throughput from the host to the flash.
1.1.1 Power Management Unit (PMU)
The power management unit (PMU) controls the power consumption of SDM4-M. It can dramatically
extend product battery life by leaving the idle part of the circuitry into sleep mode. The PMU has zero
wake-up latency.
1.1.2 SRAM Buffer
The Flash Controller performs as a SRAM buffer to optimize the host’s data transfer to and from the flash
media.
3
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
2. Functional Block
SDM4-M includes the SATA and Flash Management controllers, and flash media, as well as the SATA
standard interface. Figure 2-1 shows the functional block diagram.
Serial ATA
Interface
SATA
Controller
Flash
Management
Controller
Flash
Media
Figure 2-1: Functional block diagram
4
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
3. Pin Assignments
Power Pin1
Power cable type w/o housing
Power cable type w/ housing
GND
Vcc (+5V)
Signal Segment
Pin
Type
Signal Description
S1
GND
S2
RxP
+Differential Receive Signal
S3
RxN
-Differential Receive Signal
S4
GND
S5
TxN
-Differential Transmit Signal
S6
TxP
+Differential Transmit Signal
S7
GND
Power Segment
Pin
Signal Description
P1
Vcc (+5V)
P2
GND
5
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
Figure 3-1: SATA Cable/Connector Connection Diagram
The connector on the left represents the Host with TX/RX differential pairs connected to a cable. The
connector on the right shows the Device with TX/RX differential pairs also connected to the cable. Notice
also the ground path connecting the shielding of the cable to the Cable Receptacle.
6
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
4. Capacity Specification
Capacity specification of SDM4-M product family is available as shown in Table 4-1. It lists the specific
capacity and the default numbers of heads, sectors and cylinders for each product line.
Table 4-1: Capacity specifications
Capacity
Total bytes*
Cylinders
Heads
Sectors
Max LBA
4 GB
4,011,614,208
7,773
16
63
7,835,184
8 GB
8,012,390,400
15,525
16
63
15,649,200
16 GB
16,013,942,784
16,383
16
63
31,277,232
32 GB
32,017,047,552
16,383
16
63
62,533,296
*Display of total bytes varies from file systems.
4.1 Performance Specification
4.1.1 ATA Mode Support
SDM4-M supports the following ATA operating modes:

Supports up to PIO Mode-4

Supports up to Multi-word DMA Mode-2

Supports up to Ultra DMA Mode-5
4.1.2 Performance
Performances of SDM4-M are listed below in table 4-2.
Table 4-2: Performance (Typical)
Capacity
4 GB
8 GB
16 GB
32 GB
Sustained read (MB/s)
34
38
40
43
Sustained write (MB/s)
6
11
19
21
Performance
Note: Results may differ from various flash configurations.
7
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
4.2 Environmental Specifications
Environmental specification of SDM4-M product family which follows the MIL-STD-202 and MIL-STD-810
standards is available as shown in Table 4-3.
Table 4-3 SDM4-M environmental specifications
Item
Specification
operating temp.
0~70℃ (standard); -40 ~ +85℃ (extended)
non-operating temp.
-40~100(℃)
humidity
10~95% R.H, non-condensing
operating vibration
10~2000(Hz), 15(G), sine wave, 1(hr)/per axis
non-operating vibration
20~2000(Hz), 7.7(Grms), random wave, 1(hr)/per axis
operating shock
50(G), 11(ms), half-sine wave
non-operating shock
1500(G), 0.5(ms), half-sine wave
Note: extended operating temperature specifications are only available for 4, 8, 16GB capacities.
4.3 Mean Time Between Failures (MTBF)
Mean Time Between Failures (MTBF) is predicted based on reliability data for the individual components
in SDM4-M. Although many component MTBFs are given in databases and often these values are not
really accurate, the prediction result for SDM4-M is more than 1,000,000 hours.
Notes about the MTBF:
The MTBF is predicated and calculated based on “Telcordia Technologies Special Report, SR-332, Issue
2” method.
4.4 Certification and Compliance
SDM4-M complies with the following standards:






CE – EN55022/55024
FCC 47CFR Part15 Class B
RoHS
MIL-STD-202 and MIL-STD-810
SATA II (SATA Rev. 2.6)
Up to ATA/ATAPI-7 ( including S.M.A.R.T.)
8
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
5. Flash Management
5.1 Error Correction/Detection
SDM4-M implements a hardware ECC scheme, based on the BCH algorithm. It can detect and correct up
to 16 bits or 24 bits error in 1K bytes.
5.2 Bad Block Management
Although bad blocks on the flash media are already identified by the flash manufacturer, they can also be
accumulated over time during operation. SDM4-M’s controller maintains a table that lists those normal
blocks with disk data, the free blocks for wear leveling, and bad blocks with errors. When a normal block
is detected broken, it is replaced with a free block and listed as a bad block. When a free block is
detected broken, it is then removed from the free block list and marked as a bad block.
During device operation, this ensures that newly accumulated bad blocks are transparent to the host. The
device will stop file write service once there are only two free blocks left such that the read function is still
available for copying the files from the disk into another.
5.3 Wear Leveling
The NAND flash devices are limited by a certain number of write cycles. When using a FAT-based file
system, frequent FAT table updates are required. If some area on the flash wears out faster than others, it
would significantly reduce the lifetime of the whole SSD, even if the erase counts of others are far from
the write cycle limit. Thus, if the write cycles can be distributed evenly across the media, the lifetime of the
media can be prolonged significantly. This scheme is called wear leveling.
Apacer’s wear-leveling scheme is achieved both via buffer management and Apacer-specific static wear
leveling. They both ensure that the lifetime of the flash media can be increased, and the disk access
performance is optimized as well.
5.4 Power Failure Management
The Low Power Detection on the controller initiates crucial data saving before the power supplied to the
device is too low. This feature prevents the device from crash and ensures data integrity during an
unexpected power-off.
5.5 ATA Secure Erase
Accomplished by the Secure Erase (SE) command, which added to the open ANSI standards that control
disk drives, “ATA Secure Erase” is built into the disk drive itself and thus far less susceptible to malicious
software attacks than external software utilities. It is a positive easy-to-use data destroy command,
amounting to electronic data shredding. Executing the command causes a drive to internally completely
erase all possible user data. This command is carried out within disk drives, so no additional software is
required. Once executed, neither data nor the erase counter on the device would be recoverable, which
blurs the accuracy of device lifespan. The process to erase will not be stopped until finished while
encountering power failure, and will be continued when power is back on.
9
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
5.6 S.M.A.R.T.
S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard
allowing disk drives to automatically monitor their own health and report potential problems. It protects the
user from unscheduled downtime by monitoring and storing critical drive performance and calibration
parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure.
Apacer devices use the standard SMART command B0h to read data out from the drive to activate our
SMART feature that complies with the ATA/ATAPI-7 specifications. Based on the SFF-8035i Rev. 2.0
specifications, Apacer SMART defines vendor-specified SMART Attribute IDs (A0 ~ A5, and 0C). They
represent Initial bad block count, Bad block count, Spare block count, Maximum erase count, Average
erase count and Power cycle. When the Apacer SMART Utility running on the host, it analyzes and
reports the disk status to the host before the device reaches in critical condition.
5.7 TRIM
Made of millions of NAND flash cells, SSD can be written into groups called pages in 4K size generally,
but can only be erased in larger groups called blocks of 128 pages or 512KB. These stipulations are
partially the source of many performance issues. Until an address gets used again, the SSD has to keep
track of every last bit of data that’s written on it. The ATA-TRIM instruction tilts the balance in favor of the
SSD. TRIM addresses a major part of the performance degradation issue over time that plagues all SSDs.
A TRIM enabled drive running an OS with TRIM support will stay closer to its peak performance over time.
10
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
6. Software Interface
6.1 Command Set
This section defines the software requirements and the format of the commands the host sends to SDM4M. Commands are issued to SDM4-M by loading the required registers in the command block with the
supplied parameters, and then writing the command code to the Command register.
Table 6-1: Command set
Code
Command
Code
Command
E5h
Check Power Mode
F3h
Security Erase Prepare
06h
Data Set Management
F4h
Security Erase Unit
90h
Execute Device Diagnostic
F5h
Security Freeze Lock
E7h
Flush Cache
F1h
Security Set Password
EAh
Flush Cache EXT
F2h
Security Unlock
ECh
Identify Device
70h
Seek
E3h
Idle
EFh
Set Features
E1h
Idle Immediate
C6h
Set Multiple Mode
91h
Initialize Device Parameters
E6h
Sleep
C8h
Read DMA
B0h
SMART
25h
Read DMA EXT
E2h
Standby
C4h
Read Multiple
E0h
Standby Immediate
29h
Read Multiple EXT
CAh
Write DMA
20h
Read Sector
35h
Write DMA EXT
24h
Read Sector EXT
C5h
Write Multiple
40h
Read Verify Sectors
39h
Write Multiple EXT
42h
Read Verify Sectors EXT
30h
Write Sector
10h
Recalibrate
34h
Write Sector EXT
F6h
Security Disable Password
11
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
7. Electrical Specification
Caution: Absolute Maximum Stress Ratings – Applied conditions greater than those listed under
“Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these conditions or conditions greater than those defined in
the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating
conditions may affect device reliability.
Table 7-1: Operating range
Range
Standard
Extended Temperature
Ambient Temperature
0°C to +70°C
-40°C to 85°C
5V
4.75-5.25V
Note: extended temperature is only available for 4, 8, 16GB capacities of this product family.
Table 7-2: Absolute maximum power pin stress ratings
Parameter
Input Power
Voltage on any pin except VDD with respect to GND
Symbol
VDD
V
Conditions
-0.3V min. to 6.5V max.
-0.5V min. to VDD + 0.5V max.
Table 7-3: Recommended system power-up timing
Symbol
1
TPU-READY
1
TPU-WRITE
Parameter
Power-up to Ready Operation
Power-up to Write Operation
Typical
200
200
Maximum
1000
1000
Units
ms
ms
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
Table 7-4: Power consumption (typical)
Capacity
4 GB
8 GB
16 GB
32 GB
Active (mA)
165
165
185
185
Idle (mA)
85
85
85
85
Modes
Note: Results may differ from various flash configurations or platforms.
7.1
Electrostatic Discharge
Electrostatic discharge
Item
Amount of
Voltage
Discharge
Air
Discharge
10
+8kV
10
-8kV
12
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
25
+4kV
25
-4kV
Indirect
Discharge
(HCP)
25
+4kV
25
-4kV
Indirect
Discharge
(VCP
Front)
25
+4kV
25
-4kV
Indirect
Discharge
(VCP Left)
25
+4kV
25
-4kV
Indirect
Discharge
(VCP
Back)
25
+4kV
25
-4kV
Indirect
Discharge
(VCP
Right)
25
+4kV
25
-4kV
Contact
Discharge
7.2
Electrical Fast Transient/Burst
Electrical Fast Transient/Burst
Inject
Line
L-N-PE
Polarity
±
Voltage
kV
Inject
Time
(Second)
1kV
60
Inject
Method
Direct
Additional Information:
EUT stopped operation and could / could not be reset by operator at kV.
No false alarms or other malfunctions were observed during or after the test.
The Contact discharges were applied at least total 200 discharges at a minimum of four test points.
13
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
8. Physical Characteristics
8.1 Power Cable Type
7-pin/180 Degree Low Profile Module
8.1.1 W/o Housing
Unit: ㎜
Tolerance: ± 0.25
14
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
8.1.2 W/ Housing
Unit: ㎜
Tolerance: ± 0.25
15
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
8.2 Power Cable-less Type
7-pin/180 Degree Low Profile Module
8.2.1 W/o Housing
Unit: ㎜
Tolerance: ± 0.25
16
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
8.2.2 W/ Housing
Unit: ㎜
Tolerance: ± 0.25
17
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
9. Product Ordering Information
9.1 Product Code Designations
A P SDM x x x x X 5 AN – A CM X X
Power Source Selection
Blank: Power Cable Type
C: Power Cable-less Type
Temperature Range
Blank: Standard
W: Extended Temperature
Flash type
Version Control
Apacer Brand
Solution Version
Form Factor
A: 7P/180D without housing
B: 7P/180D with housing
Capacities:
004G:
008G:
016G:
032G:
4GB
8GB
16GB
32GB
Serial ATA Flash Module
Apacer Product Code
18
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
7.2
Valid Combinations
7P/180D LP without housing: Power Cable Type
Capacity
Standard
Extended Temperature
4GB
APSDM004GA5AN-ACM
APSDM004GA5AN-ACMW
8GB
APSDM008GA5AN-ACM
APSDM008GA5AN-ACMW
16GB
APSDM016GA5AN-ACM
APSDM016GA5AN-ACMW
32GB
APSDM032GA5AN-ACM
--
7P/180D LP with housing: Power Cable Type
Capacity
Standard
Extended Temperature
4GB
APSDM004GB5AN-ACM
APSDM004GB5AN-ACMW
8GB
APSDM008GB5AN-ACM
APSDM008GB5AN-ACMW
16GB
APSDM016GB5AN-ACM
APSDM016GB5AN-ACMW
32GB
APSDM032GB5AN-ACM
--
7P/180D LP without housing: Power Cable-less Type
Capacity
Standard
Extended Temperature
4GB
APSDM004GA5AN-ACMC
APSDM004GA5AN-ACMWC
8GB
APSDM008GA5AN-ACMC
APSDM008GA5AN-ACMWC
16GB
APSDM016GA5AN-ACMC
APSDM016GA5AN-ACMWC
32GB
APSDM032GA5AN-ACMC
--
7P/180D LP with housing: Power Cable-less Type
Capacity
Standard
Extended Temperature
4GB
APSDM004GB5AN-ACMC
APSDM004GB5AN-ACMWC
8GB
APSDM008GB5AN-ACMC
APSDM008GB5AN-ACMWC
16GB
APSDM016GB5AN-ACMC
APSDM016GB5AN-ACMWC
32GB
APSDM032GB5AN-ACMC
--
Note: Valid combinations are those products in mass production or will be in mass production. Consult your Apacer
sales representative to confirm availability of valid combinations and to determine availability of new combinations.
19
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
Revision History
Revision
Date
Description
1.0
02/22/2012
Official release
1.1
03/12/2012
Remark
Updated Product Ordering Information
Added “Housing” to physical design
Updated mechanical drawings
1.2
04/06/2012
Updated S.M.A.R.T. information
Updated Product Ordering Information
20
© 2012 Apacer Technology Inc.
Rev. 1.2
SATA-Disk Module 4
APSDMxxxxX5AN-ACMXX
Global Presence
Taiwan (Headquarters)
Apacer Technology Inc.
th
4 Fl., 75 Hsin Tai Wu Rd., Sec.1
Hsichih, New Taipei City
Taiwan 221
R.O.C.
Tel: +886-2-2698-2888
Fax: +886-2-2698-2889
[email protected]
U.S.A.
Apacer Memory America, Inc.
386 Fairview Way, Suite102,
Milpitas, CA 95035
Tel: 1-408-518-8699
Fax: 1-408-935-9611
[email protected]
Japan
Apacer Technology Corp.
5F, Matsura Bldg., Shiba, Minato-Ku
Tokyo, 105-0014, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018
[email protected]
Europe
Apacer Technology B.V.
Science Park Eindhoven 5051 5692 EB Son,
The Netherlands
Tel: 31-40-267-0000
Fax: 31-40-267-0000#6199
[email protected]
Apacer Electronic (Shanghai) Co., Ltd
1301, No.251,Xiaomuqiao Road, Shanghai,
200032, China
Tel: 86-21-5529-0222
Fax: 86-21-5206-6939
[email protected]
China
India
Apacer Technologies Pvt Ltd,
#1064, 1st Floor, 7th ‘A’ Main,
3rd Block Koramangala, Bangalore – 560 034
Tel: +91 80 4152 9061/62/63
Fax: +91 80 4170 0215
[email protected]
21
© 2012 Apacer Technology Inc.
Rev. 1.2
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apacer:
APSDM004GA5AN-ACM APSDM008GA5AN-ACM APSDM016GA5AN-ACM APSDM032GA5AN-ACM
Similar pages