Cypress MB9AFB42NPQC-G-JNE2 32-bit armâ® cortexâ®-m3 fm3 microcontroller Datasheet

MB9AB40NB Series
32-bit ARM® Cortex®-M3
FM3 Microcontroller
The MB9AB40NB Series are highly integrated 32-bit microcontrollers dedicated for embedded controllers with
low-power consumption mode and competitive cost.
These series are based on the ARM Cortex-M3 Processor with on-chip Flash memory and SRAM, and have
peripheral functions such as various timers, ADCs, LCDC and Communication Interfaces (USB, UART, CSIO, I 2C).
The products which are described in this data sheet are placed into TYPE6 product categories in FM3 Family
Peripheral Manual.
Features
32-bit ARM Cortex-M3 Core
USB Interface
 Processor version: r2p1
The USB interface is composed of Device and Host. PLL for
USB is built-in, USB clock can be generated by multiplication
of Main clock.
 Up to 40 MHz Frequency Operation
 Integrated Nested Vectored Interrupt Controller (NVIC): 1
NMI (non-maskable interrupt) and
48 peripheral interrupts and 16 priority levels
[USB device]
 24-bit System timer (Sys Tick): System timer for OS task
management
 USB2.0 Full-Speed supported
 Max 6 EndPoint supported

[Flash memory]

 Dual operation Flash memory




EndPoint 0 is control transfer
EndPoint 1, 2 can select Bulk-transfer,
Interrupt-transfer or Isochronous-transfer
EndPoint 3 to 5 can select Bulk-transfer or
Interrupt-transfer
EndPoint 1 to 5 is comprised of Double Buffers.
The size of each endpoint is according to the follows.
Endpoint 0, 2 to 5: 64 bytes
Endpoint 1: 256 bytes

On-chip Memories
Dual Operation Flash memory has the upper bank and
the lower bank. So, this series could implement erase,
write and read operations for each bank
simultaneously.
Main area: Up to 256 Kbytes (Up to 240 Kbytes upper
bank + 16 Kbytes lower bank)
Work area: 32 Kbytes (lower bank)

•
•
[USB host]
 USB2.0 Full/Low-speed supported
 Bulk-transfer, interrupt-transfer and Isochronous-transfer
 Read cycle: 0 wait-cycle
support
 Security function for code protection
 USB Device connected/disconnected automatic detection
[SRAM]
 Automatic processing of the IN/OUT token handshake
packet
This Series on-chip SRAM is composed of two independent
SRAM (SRAM0, SRAM1). SRAM0 is connected to I-code bus
and D-code bus of Cortex-M3 core. SRAM1 is connected to
System bus.
 Max 256-byte packet-length supported
 SRAM0: Up to 16 Kbytes
LCD Controller (LCDC)
 SRAM1: Up to 16 Kbytes
 Up to 40 SEG × 8 COM
External Bus Interface*
 8 COM or 4 COM mode can be selected.
 Supports SRAM, NOR Flash memory device
 Built-in internal dividing resistor
 Up to 8 chip selects
 LCD drive power supply (bias) pin (VV4 to VV0)
 8-/16-bit Data width
 With blinking function
 Wake-up function supported
 Up to 25-bit Address bit
 Maximum area size : Up to 256 Mbytes
 Supports Address/Data multiplex
 Supports external RDY function
*: MB9AFB41LB, FB42LB and FB44LB do not support
External Bus Interface.
Cypress Semiconductor Corporation
Document Number: 002-05631 Rev *B
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised July 26, 2017
MB9AB40NB Series
Multi-function Serial Interface (Max 8channels)
Base Timer (Max 8 channels)
 4 channels with 16steps×9-bit FIFO (ch.4 to ch.7), 4
Operation mode is selectable from the following for each
channel.
channels without FIFO (ch.0 to ch.3)
 Operation mode is selectable from the following for each
channel.

UART

CSIO

I2 C
 16-bit PWM timer
 16-bit PPG timer
 16-/32-bit reload timer
 16-/32-bit PWC timer
[UART]
General-Purpose I/O Port
 Full-duplex double buffer
 Built-in dedicated baud rate generator
This series can use its pins as general-purpose I/O ports when
they are not used for external bus or peripherals. Moreover,
the port relocate function is built in. It can set which I/O port
the peripheral function can be allocated to.
 External clock available as a serial clock
 Capable of pull-up control per pin
 Hardware Flow control* : Automatically control the
 Capable of reading pin level directly
 Selection with or without parity supported
transmission by CTS/RTS (only ch.4)
 Various error detection functions available (parity errors,
framing errors, and overrun errors)
*: MB9AFB41LB, FB42LB and FB44LB do not support
Hardware Flow control.
 Built-in the port relocate function
 Up to 83 fast general-purpose I/O Ports@100 pin Package
 Some ports are 5 V tolerant.
See Pin Assignment to confirm the corresponding pins.
[CSIO]
Dual Timer (32-/16-bit Down Counter)
 Full-duplex double buffer
 Overrun error detection function available
The Dual Timer consists of two programmable 32-/16-bit down
counters.
Operation mode is selectable from the following for each
channel.
[I2C]
 Free-running
 Built-in dedicated baud rate generator
Standard-mode (Max 100 kbps) / Fast-mode (Max 400 kbps)
supported
DMA Controller (8 channels)
The DMA Controller has an independent bus from the CPU, so
CPU and DMA Controller can process simultaneously.
 8 independently configured and operated channels
 Transfer can be started by software or request from the
built-in peripherals
 Transfer address area: 32-bit (4 Gbytes)
 Transfer mode: Block transfer/Burst transfer/Demand
transfer
 Transfer data type: byte/half-word/word
 Periodic (=Reload)
 One-shot
HDMI-CEC/Remote Control Receiver (Up to 2
channels)
[HDMI-CEC transmitter]
 Header block automatic transmission by judging Signal free
 Generating status interrupt by detecting Arbitration lost
 Generating START, EOM, ACK automatically to output CEC
transmission by setting 1 byte data
 Generating transmission status interrupt when transmitting
1 block (1 byte data and EOM/ACK)
 Transfer block count: 1 to 16
[HDMI-CEC receiver]
 Number of transfers: 1 to 65536
 Automatic ACK reply function available
A/D Converter (Max 24 channels)
[12-bit A/D Converter]
 Successive Approximation type
 Built-in 2 units
 Line error detection function available
[Remote control receiver]
 4 bytes reception buffer
 Repeat code detection function available
 Conversion time: 2.0 μs @ 2.7 V to 3.6 V
 Priority conversion available (priority at 2 levels)
 Scanning conversion mode
 Built-in FIFO for conversion data storage (for SCAN
conversion: 16 steps, for Priority conversion: 4 steps)
Document Number: 002-05631 Rev *B
Page 2 of 128
MB9AB40NB Series
Real-time clock (RTC)
[Resets]
The Real-time clock can count
year/Month/Day/Hour/Minute/Second/A day of the week from
00 to 99.
 Reset requests from INITX pin
 The interrupt function with specifying date and time
(Year/Month/Day/Hour/Minute) is available. This function is
also available by specifying only Year, Month, Day, Hour or
Minute.
 Power on reset
 Software reset
 Watchdog timers reset
 Low-voltage detection reset
 Clock Super Visor reset
 Timer interrupt function after set time or each set time.
 Capable of rewriting the time with continuing the time count.
Clock Super Visor (CSV)
 Leap year automatic count is available.
Clocks generated by built-in CR oscillators are used to
supervise abnormality of the external clocks.
Watch Counter
 External clock failure (clock stop) is detected, reset is
 The Watch counter is used for wake up from sleep and
timer mode.
 Interval timer: up to 64 s (Max) @ Sub Clock: 32.768 kHz
asserted.
 External frequency anomaly is detected, interrupt or reset is
asserted.
External Interrupt Controller Unit
Low-Voltage Consumption Detector (LVD)
 Up to 16 external interrupt input pins
 This Series includes 2-stage monitoring of voltage on the
 Include one non-maskable interrupt (NMI) input pin
Watchdog Timer (2 channels)
 A watchdog timer can generate interrupts or a reset when a
time-out value is reached.
 This series consists of two different watchdogs, a Hardware
watchdog and a Software watchdog.
 The Hardware watchdog timer is clocked by the built-in
low-speed CR oscillator. Therefore, the Hardware watchdog
is active in any low-power consumption modes except RTC,
Stop, Deep Standby RTC, Deep Standby Stop modes.
VCC pins. When the voltage falls below the voltage that has
been set, Low-Voltage Detector generates an interrupt or
reset.
 LVD1: error reporting via interrupt
 LVD2: auto-reset operation
Low-Power Consumption Mode
 Six low-power consumption modes supported.




CRC (Cyclic Redundancy Check) Accelerator

The CRC accelerator calculates the CRC which has a heavy
software processing load, and achieves a reduction of the
integrity check processing load for reception data and storage.

Sleep
Timer
RTC
Stop
Deep Standby RTC (selectable between keeping the
value of RAM and not)
Deep Standby Stop (selectable between keeping the
value of RAM and not)
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
Debug
 CCITT CRC16 Generator Polynomial: 0x1021
 Serial Wire JTAG Debug Port (SWJ-DP)
 IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
 Embedded Trace Macrocells (ETM).*
Clock and Reset
*: MB9AFB41LB/MB, FB42LB/MB, FB44LB/MB support only
SWJ-DP.
[Clocks]
Unique ID
 Selectable from five clock sources (2 external oscillators, 2
Unique value of the device (41-bit) is set.
built-in CR oscillators, and Main PLL).
 Main Clock: 4 MHz to 48 MHz
Power Supply
 Sub Clock: 32.768 kHz
Wide range voltage:
 Built-in high-speed CR Clock: 4 MHz
VCC = 1.65 V to 3.6 V
 Built-in low-speed CR Clock: 100 kHz
VCC = 3.0 V to 3.6 V (when USB is used)
 Main PLL Clock
VCC = 2.2 V to 3.6 V (when LCDC is used)
Document Number: 002-05631 Rev *B
Page 3 of 128
MB9AB40NB Series
Contents
Features.......................................................................................................................................................................... 1
1.
Product Lineup ...................................................................................................................................................... 6
2.
Packages................................................................................................................................................................ 7
3.
Pin Assignment ..................................................................................................................................................... 8
4.
List of Pin Functions ........................................................................................................................................... 15
4.1
List of Pin Numbers ............................................................................................................................................ 15
4.2
List of Pin Functions ........................................................................................................................................... 26
5.
I/O Circuit Type .................................................................................................................................................... 41
6.
Handling Precautions ......................................................................................................................................... 48
6.1
Precautions for Product Design .......................................................................................................................... 48
6.2
Precautions for Package Mounting ..................................................................................................................... 49
6.3
Precautions for Use Environment ....................................................................................................................... 51
7.
Handling Devices ................................................................................................................................................ 52
8.
Block Diagram ..................................................................................................................................................... 54
9.
Memory Size ........................................................................................................................................................ 54
10. Memory Map ........................................................................................................................................................ 55
11. Pin Status in Each CPU State ............................................................................................................................. 58
12. List of Pin Status ................................................................................................................................................. 59
13. Electrical Characteristics ................................................................................................................................... 66
13.1 Absolute Maximum Ratings ................................................................................................................................ 66
13.2 Recommended Operating Conditions................................................................................................................. 67
13.3 DC Characteristics.............................................................................................................................................. 68
13.3.1 Current rating ...................................................................................................................................................... 68
13.3.2 Pin Characteristics .............................................................................................................................................. 71
13.4 LCD Characteristics............................................................................................................................................ 72
13.5 AC Characteristics .............................................................................................................................................. 73
13.5.1 Main Clock Input Characteristics ......................................................................................................................... 73
13.5.2 Sub Clock Input Characteristics .......................................................................................................................... 74
13.5.3 Built-in CR Oscillation Characteristics ................................................................................................................. 74
13.5.4 Operating Conditions of Main and USB PLL ....................................................................................................... 75
13.5.5 Reset Input Characteristics ................................................................................................................................. 76
13.5.6 Power-on Reset Timing....................................................................................................................................... 77
13.5.7 External Bus Timing ............................................................................................................................................ 78
13.5.8 Base Timer Input Timing ..................................................................................................................................... 85
13.5.9 CSIO/UART Timing ............................................................................................................................................. 86
13.5.10 External Input Timing ....................................................................................................................................... 94
13.5.11 I2C Timing ........................................................................................................................................................ 95
13.5.12 ETM Timing ..................................................................................................................................................... 96
13.5.13 JTAG Timing .................................................................................................................................................... 97
13.6 12-bit A/D Converter ........................................................................................................................................... 98
13.7 USB Characteristics ......................................................................................................................................... 101
13.8 Low-Voltage Detection Characteristics ............................................................................................................. 105
13.8.1 Interrupt of Low-Voltage Detection .................................................................................................................... 106
13.9 Flash Memory Write/Erase Characteristics ...................................................................................................... 107
13.9.1 Write / Erase time.............................................................................................................................................. 107
13.9.2 Write cycles and data hold time ........................................................................................................................ 107
13.10 Return Time from Low-Power Consumption Mode ........................................................................................... 108
13.10.1 Return Factor: Interrupt/WKUP ...................................................................................................................... 108
13.10.2 Return Factor: Reset ..................................................................................................................................... 109
14. Ordering Information ........................................................................................................................................ 111
Document Number: 002-05631 Rev *B
Page 4 of 128
MB9AB40NB Series
15. Package Dimensions ........................................................................................................................................ 112
16. Errata .................................................................................................................................................................. 121
16.1 Part Numbers Affected ..................................................................................................................................... 121
16.2 Qualification Status........................................................................................................................................... 121
16.3 Errata Summary ............................................................................................................................................... 121
17. Major Changes .................................................................................................................................................. 125
Document History ...................................................................................................................................................... 127
Sales, Solutions, and Legal Information .................................................................................................................. 128
Document Number: 002-05631 Rev *B
Page 5 of 128
MB9AB40NB Series
1.
Product Lineup
Memory size
Product name
On-chip
Flash
memory
On-chip
SRAM
MB9AFB41LB/MB/NB
MB9AFB42LB/MB/NB
MB9AFB44LB/MB/NB
Main area
64 Kbytes
128 Kbytes
256 Kbytes
Work area
32 Kbytes
32 Kbytes
32 Kbytes
SRAM0
8 Kbytes
8 Kbytes
16 Kbytes
SRAM1
8 Kbytes
8 Kbytes
16 Kbytes
Total
16 Kbytes
16 Kbytes
32 Kbytes
Function
MB9AFB41LB
MB9AFB42LB
MB9AFB44LB
Product name
Pin count
CPU
Freq.
Power supply voltage range
USB2.0 (Device/Host)
DMAC
64
Cortex-M3
40 MHz
1.65 V to 3.6 V
1 ch.
8 ch.
MB9AFB41MB
MB9AFB42MB
MB9AFB44MB
80/96
MB9AFB41NB
MB9AFB42NB
MB9AFB44NB
100/112
Addr: 21-bit (Max)
R/W Data: 8-bit (Max)
CS: 4 (Max)
Support: SRAM, NOR
Flash memory
33 SEG × 8 COM
(Max)
Addr: 25-bit (Max)
R/W Data: 8-/16-bit (Max)
CS: 8 (Max)
Support: SRAM,
NOR Flash memory
40 SEG × 8 COM
(Max)
External Bus Interface
-
LCD Controller
20 SEG × 8 COM (Max)
MF Serial Interface
(UART/CSIO/I2C)
8 ch. (Max) ch.4 to ch.7: FIFO (16 steps × 9-bit)
ch.0 to ch.3: No FIFO
Base Timer
(PWC/Reload timer/PWM/PPG)
8 ch. (Max)
Dual Timer
1 unit
HDMI-CEC/ Remote Control Receiver
Real-Time Clock
Watch Counter
CRC Accelerator
Watchdog timer
External Interrupts
I/O ports
12-bit A/D converter
CSV (Clock Super Visor)
LVD (Low-Voltage Detector)
High-speed
Built-in CR
Low-speed
Debug Function
Unique ID
2 ch. (Max)
1 unit
1 unit
Yes
1 ch. (SW) + 1 ch. (HW)
8 pins (Max) + NMI × 1
51 pins (Max)
12 ch. (2 units)
Yes
2 ch.
4 MHz
100 kHz
SWJ-DP
Yes
11 pins (Max) + NMI × 1
66 pins (Max)
17 ch. (2 units)
16 pins (Max) + NMI × 1
83 pins (Max)
24 ch. (2 units)
SWJ-DP/ETM
Note:
−
All signals of the peripheral function in each product cannot be allocated by limiting the pins of package. It is necessary to use
the port relocate function of the I/O port according to your function use.
−
See Electrical Characteristics12.5 AC Characteristics 12.5.3 Built-in CR Oscillation Characteristics for accuracy of built-in CR.
Document Number: 002-05631 Rev *B
Page 6 of 128
MB9AB40NB Series
2.
Packages
MB9AFB41LB
MB9AFB42LB
MB9AFB44LB
Product name
Package



MB9AFB41MB
MB9AFB42MB
MB9AFB44MB
MB9AFB41NB
MB9AFB42NB
MB9AFB44NB
-
-
-
-
-
-
LQFP:
LQD064 (0.5mm pitch)
LQFP:
LQG064 (0.65mm pitch)
QFN:
VNC064 (0.5mm pitch)
LQFP:
LQH080 (0.5mm pitch)
-
LQFP:
LQJ080 (0.65mm pitch)
-
BGA:
FDG096 (0.5mm pitch)
-
LQFP:
LQI100 (0.5mm pitch)
-
-
QFP:
PQH100 (0.65mm pitch)
-
-
BGA:
LBC112 (0.8mm pitch)
-
-



-



: Supported
Note:
−
See Package Dimensions for detailed information on each package.
Document Number: 002-05631 Rev *B
Page 7 of 128
MB9AB40NB Series
3.
Pin Assignment
LQI100
P01/TCK/SWCLK
P00/TRSTX/MCSX7_1
VCC
78
77
76
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI/MCSX6_1
81
80
79
P06/AN21/TRACED1/TIOB5_2/SOT4_2/INT01_1/SEG08/MCSX4_1
P05/AN20/TRACED0/TIOA5_2/SIN4_2/INT00_1/SEG09/MCSX5_1
84
83
82
P09/TRACECLK/TIOB0_2/RTS4_2/SEG05/MCSX2_1
P08/AN23/TRACED3/TIOA0_2/CTS4_2/SEG06/MCSX3_1
P07/AN22/TRACED2/ADTG_0/SCK4_2/SEG07/MCLKOUT_1
86
85
P0C/SCK4_0/TIOA6_1/MALE_1
P0B/SOT4_0/TIOB6_1/MCSX0_1
P0A/SIN4_0/INT00_2/MCSX1_1
89
88
87
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0E/CTS4_0/TIOB3_2/SEG03/MDQM1_1
P0D/RTS4_0/TIOA3_2/SEG04/MDQM0_1
92
91
90
P62/SCK5_0/ADTG_3/SEG01/MOEX_1
P63/INT03_0/SEG02/MWEX_1
94
93
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1
P61/SOT5_0/TIOB2_2/UHCONX/SEG00
97
96
99
98
95
VSS
P81/UDP0
P80/UDM0
100
(TOP VIEW)
VCC
1
75
VSS
P50/INT00_0/SIN3_1/VV4/MADATA00_1
2
74
P20/AN19/INT05_0/CROUT_0/SEG10/MAD24_1
P51/INT01_0/SOT3_1/VV3/MADATA01_1
3
73
P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P52/INT02_0/SCK3_1/VV2/MADATA02_1
4
72
P22/AN17/SOT0_0/TIOB7_1/SEG12
P53/SIN6_0/TIOA1_2/INT07_2/VV1/MADATA03_1
5
71
P23/AN16/SCK0_0/TIOA7_1/SEG13
P54/SOT6_0/TIOB1_2/VV0/MADATA04_1
6
70
P1F/AN15/ADTG_5/MAD23_1
P55/SCK6_0/ADTG_1/SEG39/MADATA05_1
7
69
P1E/AN14/RTS4_1/SEG14/MAD22_1
P56/INT08_2/SEG38/MADATA06_1
8
68
P1D/AN13/CTS4_1/SEG15/MAD21_1
P30/TIOB0_1/INT03_2/COM7/MADATA07_1
9
67
P1C/AN12/SCK4_1/SEG16/MAD20_1
P31/TIOB1_1/SCK6_1/INT04_2/COM6/MADATA08_1
10
66
P1B/AN11/SOT4_1/SEG17/MAD19_1
65
P1A/AN10/SIN4_1/INT05_1/SEG18/MAD18_1
64
P19/AN09/SCK2_2/SEG19/MAD17_1
P32/TIOB2_1/SOT6_1/INT05_2/COM5/MADATA09_1
11
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/COM4/MADATA10_1
12
P34/TIOB4_1/MADATA11_1
13
63
P18/AN08/SOT2_2/SEG20/MAD16_1
P35/TIOB5_1/INT08_1/MADATA12_1
14
62
AVSS
LQFP - 100
48
49
50
PE2/X0
VSS
MD0
PE3/X1
45
46
47
PE0/MD1
P4D/TIOB4_0/SOT7_1/MAD07_1
P4E/TIOB5_0/INT06_2/SIN7_1/MAD08_1
42
43
44
P4C/TIOB3_0/SCK7_1/CEC0/MAD06_1
40
VSS
P42/TIOA2_0
41
VCC
P4B/TIOB2_0/SEG29/MAD05_1
51
P49/TIOB0_0/SOT3_2/SEG31/MAD03_1
25
P4A/TIOB1_0/SCK3_2/SEG30/MAD04_1
P10/AN00/SEG28
VSS
37
52
38
24
39
P11/AN01/SIN1_1/INT02_1/WKUP1/SEG27/MAD09_1
P3F/TIOA5_1/SEG35
INITX
53
P47/X1A
23
P48/INT14_1/SIN3_2/SEG32/MAD02_1
P12/AN02/SOT1_1/SEG26/MAD10_1
P3E/TIOA4_1/SEG36
34
54
35
22
36
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/SEG25/MAD11_1
P3D/TIOA3_1/SEG37
VCC
P14/AN04/SIN0_1/INT03_1/SEG24/MAD12_1
55
P46/X0A
56
21
32
20
P3C/TIOA2_1/COM0
33
P15/AN05/SOT0_1/SEG23/MAD13_1
P3B/TIOA1_1/COM1
C
57
P45/TIOA5_0/SEG33/MAD01_1
19
29
P16/AN06/SCK0_1/SEG22/MAD14_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2/COM2
30
58
31
18
P43/TIOA3_0/ADTG_7
P17/AN07/SIN2_2/INT04_1/SEG21/MAD15_1
P39/ADTG_2/COM3
P44/TIOA4_0/SEG34/MAD00_1
59
26
17
27
AVCC
P38/SCK5_2/INT11_1/MADATA15_1
28
AVRH
60
VCC
61
16
P40/TIOA0_0/INT12_1
15
P41/TIOA1_0/INT13_1
P36/SIN5_2/INT09_1/MADATA13_1
P37/SOT5_2/INT10_1/MADATA14_1
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 002-05631 Rev *B
Page 8 of 128
MB9AB40NB Series
PQH100
VCC
VSS
P20/AN19/INT05_0/CROUT_0/SEG10/MAD24_1
P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
54
53
52
51
P02/TDI/MCSX6_1
P01/TCK/SWCLK
P00/TRSTX/MCSX7_1
57
56
55
P04/TDO/SWO
P03/TMS/SWDIO
59
58
P07/AN22/TRACED2/ADTG_0/SCK4_2/SEG07/MCLKOUT_1
P06/AN21/TRACED1/TIOB5_2/SOT4_2/INT01_1/SEG08/MCSX4_1
P05/AN20/TRACED0/TIOA5_2/SIN4_2/INT00_1/SEG09/MCSX5_1
62
61
60
P0A/SIN4_0/INT00_2/MCSX1_1
P09/TRACECLK/TIOB0_2/RTS4_2/SEG05/MCSX2_1
P08/AN23/TRACED3/TIOA0_2/CTS4_2/SEG06/MCSX3_1
65
64
63
P0C/SCK4_0/TIOA6_1/MALE_1
P0B/SOT4_0/TIOB6_1/MCSX0_1
67
66
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0E/CTS4_0/TIOB3_2/SEG03/MDQM1_1
P0D/RTS4_0/TIOA3_2/SEG04/MDQM0_1
70
69
68
P62/SCK5_0/ADTG_3/SEG01/MOEX_1
P63/INT03_0/SEG02/MWEX_1
72
71
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1
P61/SOT5_0/TIOB2_2/UHCONX/SEG00
75
74
73
VSS
P81/UDP0
P80/UDM0
78
77
76
P50/INT00_0/SIN3_1/VV4/MADATA00_1
VCC
80
79
(TOP VIEW)
P51/INT01_0/SOT3_1/VV3/MADATA01_1
81
50
P22/AN17/SOT0_0/TIOB7_1/SEG12
P52/INT02_0/SCK3_1/VV2/MADATA02_1
82
49
P23/AN16/SCK0_0/TIOA7_1/SEG13
P53/SIN6_0/TIOA1_2/INT07_2/VV1/MADATA03_1
83
48
P1F/AN15/ADTG_5/MAD23_1
P54/SOT6_0/TIOB1_2/VV0/MADATA04_1
84
47
P1E/AN14/RTS4_1/SEG14/MAD22_1
P55/SCK6_0/ADTG_1/SEG39/MADATA05_1
85
46
P1D/AN13/CTS4_1/SEG15/MAD21_1
P56/INT08_2/SEG38/MADATA06_1
86
45
P1C/AN12/SCK4_1/SEG16/MAD20_1
P30/TIOB0_1/INT03_2/COM7/MADATA07_1
87
44
P1B/AN11/SOT4_1/SEG17/MAD19_1
P31/TIOB1_1/SCK6_1/INT04_2/COM6/MADATA08_1
88
43
P1A/AN10/SIN4_1/INT05_1/SEG18/MAD18_1
P32/TIOB2_1/SOT6_1/INT05_2/COM5/MADATA09_1
89
42
P19/AN09/SCK2_2/SEG19/MAD17_1
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/COM4/MADATA10_1
90
41
P18/AN08/SOT2_2/SEG20/MAD16_1
P34/TIOB4_1/MADATA11_1
91
40
AVSS
P35/TIOB5_1/INT08_1/MADATA12_1
92
39
AVRH
P36/SIN5_2/INT09_1/MADATA13_1
93
38
AVCC
P37/SOT5_2/INT10_1/MADATA14_1
94
37
P17/AN07/SIN2_2/INT04_1/SEG21/MAD15_1
P38/SCK5_2/INT11_1/MADATA15_1
95
36
P16/AN06/SCK0_1/SEG22/MAD14_1
P39/ADTG_2/COM3
96
35
P15/AN05/SOT0_1/SEG23/MAD13_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2/COM2
97
34
P14/AN04/SIN0_1/INT03_1/SEG24/MAD12_1
P3B/TIOA1_1/COM1
98
33
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/SEG25/MAD11_1
P3C/TIOA2_1/COM0
99
32
P12/AN02/SOT1_1/SEG26/MAD10_1
P3D/TIOA3_1/SEG37
100
31
P11/AN01/SIN1_1/INT02_1/WKUP1/SEG27/MAD09_1
27
28
29
30
PE3/X1
VSS
VCC
P10/AN00/SEG28
24
25
26
MD0
PE0/MD1
PE2/X0
22
23
P4D/TIOB4_0/SOT7_1/MAD07_1
P4B/TIOB2_0/SEG29/MAD05_1
P4C/TIOB3_0/SCK7_1/CEC0/MAD06_1
P4E/TIOB5_0/INT06_2/SIN7_1/MAD08_1
19
20
21
P4A/TIOB1_0/SCK3_2/SEG30/MAD04_1
16
17
18
INITX
P48/INT14_1/SIN3_2/SEG32/MAD02_1
14
15
P46/X0A
P47/X1A
P49/TIOB0_0/SOT3_2/SEG31/MAD03_1
11
12
13
C
VSS
VCC
9
10
P44/TIOA4_0/SEG34/MAD00_1
P45/TIOA5_0/SEG33/MAD01_1
6
7
8
P42/TIOA2_0
P41/TIOA1_0/INT13_1
P43/TIOA3_0/ADTG_7
3
4
5
VSS
VCC
P3F/TIOA5_1/SEG35
P40/TIOA0_0/INT12_1
1
2
P3E/TIOA4_1/SEG36
QFP - 100
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 002-05631 Rev *B
Page 9 of 128
MB9AB40NB Series
LQH080/LQJ080
P02/TDI/MCSX6_1
P01/TCK/SWCLK
P00/TRSTX/MCSX7_1
63
62
61
P04/TDO/SWO
P03/TMS/SWDIO
65
64
P0A/SIN4_0/INT00_2/MCSX1_1
P07/AN22/ADTG_0/SEG07/MCLKOUT_1
67
66
P0C/SCK4_0/TIOA6_1/MALE_1
P0B/SOT4_0/TIOB6_1/MCSX0_1
68
70
69
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0E/CTS4_0/TIOB3_2/SEG03/MDQM1_1
P0D/RTS4_0/TIOA3_2/SEG04/MDQM0_1
72
71
P62/SCK5_0/ADTG_3/SEG01/MOEX_1
P63/INT03_0/SEG02/MWEX_1
74
73
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1
P61/SOT5_0/TIOB2_2/UHCONX/SEG00
76
75
P80/UDM0
VCC
78
77
VSS
P81/UDP0
80
79
(TOP VIEW)
VCC
1
60
P20/AN19/INT05_0/CROUT_0/SEG10/MAD24_1
P50/INT00_0/SIN3_1/VV4/MADATA00_1
2
59
P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P51/INT01_0/SOT3_1/VV3/MADATA01_1
3
58
P22/AN17/SOT0_0/TIOB7_1/SEG12
P52/INT02_0/SCK3_1/VV2/MADATA02_1
4
57
P23/AN16/SCK0_0/TIOA7_1/SEG13
P53/SIN6_0/TIOA1_2/INT07_2/VV1/MADATA03_1
5
56
P1B/AN11/SOT4_1/SEG17/MAD19_1
P54/SOT6_0/TIOB1_2/VV0/MADATA04_1
6
55
P1A/AN10/SIN4_1/INT05_1/SEG18/MAD18_1
P55/SCK6_0/ADTG_1/SEG39/MADATA05_1
7
54
P19/AN09/SCK2_2/SEG19/MAD17_1
P56/INT08_2/SEG38/MADATA06_1
8
53
P18/AN08/SOT2_2/SEG20/MAD16_1
P30/TIOB0_1/INT03_2/COM7/MADATA07_1
9
52
AVSS
P31/TIOB1_1/SCK6_1/INT04_2/COM6/MADATA08_1
10
51
AVRH
P32/TIOB2_1/SOT6_1/INT05_2/COM5/MADATA09_1
11
50
AVCC
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/COM4/MADATA10_1
12
49
P17/AN07/SIN2_2/INT04_1/SEG21/MAD15_1
P39/ADTG_2/COM3
13
48
P16/AN06/SCK0_1/SEG22/MAD14_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2/COM2
14
47
P15/AN05/SOT0_1/SEG23/MAD13_1
P3B/TIOA1_1/COM1
15
46
P14/AN04/SIN0_1/INT03_1/SEG24/MAD12_1
P3C/TIOA2_1/COM0
16
45
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/SEG25/MAD11_1
P3D/TIOA3_1/SEG37
17
44
P12/AN02/SOT1_1/SEG26/MAD10_1
P3E/TIOA4_1/SEG36
18
43
P11/AN01/SIN1_1/INT02_1/WKUP1/SEG27/MAD09_1
P3F/TIOA5_1/SEG35
19
42
P10/AN00/SEG28
VSS
20
41
VCC
38
39
40
PE2/X0
VSS
MD0
PE3/X1
36
37
PE0/MD1
34
35
P4D/TIOB4_0/SOT7_1/MAD07_1
33
P4E/TIOB5_0/INT06_2/SIN7_1/MAD08_1
31
32
P4B/TIOB2_0/SEG29/MAD05_1
P4C/TIOB3_0/SCK7_1/CEC0/MAD06_1
29
30
P48/INT14_1/SIN3_2/SEG32/MAD02_1
INITX
P49/TIOB0_0/SOT3_2/SEG31/MAD03_1
27
28
P47/X1A
P4A/TIOB1_0/SCK3_2/SEG30/MAD04_1
25
26
VCC
P46/X0A
23
24
C
VSS
21
22
P44/TIOA4_0/SEG34/MAD00_1
P45/TIOA5_0/SEG33/MAD01_1
LQFP - 80
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 002-05631 Rev *B
Page 10 of 128
MB9AB40NB Series
LQD064/LQG064
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
52
51
50
49
P0A/SIN4_0/INT00_2
P04/TDO/SWO
54
53
P0C/SCK4_0/TIOA6_1
P0B/SOT4_0/TIOB6_1
56
55
P62/SCK5_0/ADTG_3/SEG01
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
58
57
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1
P61/SOT5_0/TIOB2_2/UHCONX/SEG00
60
59
P80/UDM0
VCC
62
61
VSS
P81/UDP0
64
63
(TOP VIEW)
VCC
1
48
P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P50/INT00_0/SIN3_1/VV4
2
47
P22/AN17/SOT0_0/TIOB7_1/SEG12
P51/INT01_0/SOT3_1
3
46
P23/AN16/SCK0_0/TIOA7_1/SEG13
P52/INT02_0/SCK3_1
4
45
P19/AN09/SCK2_2/SEG19
P30/TIOB0_1/INT03_2/COM7
5
44
P18/AN08/SOT2_2/SEG20
P31/TIOB1_1/SCK6_1/INT04_2/COM6
6
43
AVSS
P32/TIOB2_1/SOT6_1/INT05_2/COM5
7
42
AVRH
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/COM4
8
41
AVCC
P39/ADTG_2/COM3
9
40
P17/AN07/SIN2_2/INT04_1/SEG21
P3A/TIOA0_1/RTCCO_2/SUBOUT_2/COM2
10
39
P15/AN05/SEG23
P3B/TIOA1_1/COM1
11
38
P14/AN04/INT03_1/SEG24
P3C/TIOA2_1/COM0
12
37
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/SEG25
P3D/TIOA3_1/SEG37
13
36
P12/AN02/SOT1_1/SEG26
P3E/TIOA4_1/SEG36
14
35
P11/AN01/SIN1_1/INT02_1/WKUP1/SEG27
P3F/TIOA5_1/SEG35
15
34
P10/AN00/SEG28
VSS
16
33
VCC
29
31
32
PE3/X1
VSS
PE0/MD1
30
P4E/TIOB5_0/INT06_2/SIN7_1
MD0
27
28
P4D/TIOB4_0/SOT7_1
PE2/X0
25
26
P4C/TIOB3_0/SCK7_1/CEC0
23
24
P4A/TIOB1_0/SEG30
P4B/TIOB2_0/SEG29
21
22
INITX
19
20
P46/X0A
P47/X1A
P49/TIOB0_0/SEG31
17
18
C
VCC
LQFP - 64
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 002-05631 Rev *B
Page 11 of 128
MB9AB40NB Series
VNC064
VSS
P81/UDP0
P80/UDM0
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1
P61/SOT5_0/TIOB2_2/UHCONX/SEG00
P62/SCK5_0/ADTG_3/SEG01
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0C/SCK4_0/TIOA6_1
P0B/SOT4_0/TIOB6_1
P0A/SIN4_0/INT00_2
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
(TOP VIEW)
VCC
1
48
P21/AN18/SIN0_0/INT06_1/WKUP2/SEG11
P50/INT00_0/SIN3_1/VV4
2
47
P22/AN17/SOT0_0/TIOB7_1/SEG12
P51/INT01_0/SOT3_1
3
46
P23/AN16/SCK0_0/TIOA7_1/SEG13
P52/INT02_0/SCK3_1
4
45
P19/AN09/SCK2_2/SEG19
P30/TIOB0_1/INT03_2/COM7
5
44
P18/AN08/SOT2_2/SEG20
P31/TIOB1_1/SCK6_1/INT04_2/COM6
6
43
AVSS
P32/TIOB2_1/SOT6_1/INT05_2/COM5
7
42
AVRH
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/COM4
8
41
AVCC
P39/ADTG_2/COM3
9
40
P17/AN07/SIN2_2/INT04_1/SEG21
P3A/TIOA0_1/RTCCO_2/SUBOUT_2/COM2
10
39
P15/AN05/SEG23
P3B/TIOA1_1/COM1
11
38
P14/AN04/INT03_1/SEG24
P3C/TIOA2_1/COM0
12
37
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/SEG25
P3D/TIOA3_1/SEG37
13
36
P12/AN02/SOT1_1/SEG26
P3E/TIOA4_1/SEG36
14
35
P11/AN01/SIN1_1/INT02_1/WKUP1/SEG27
P3F/TIOA5_1/SEG35
15
34
P10/AN00/SEG28
VSS
16
33
VCC
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
C
VCC
P46/X0A
P47/X1A
INITX
P49/TIOB0_0/SEG31
P4A/TIOB1_0/SEG30
P4B/TIOB2_0/SEG29
P4C/TIOB3_0/SCK7_1/CEC0
P4D/TIOB4_0/SOT7_1
P4E/TIOB5_0/INT06_2/SIN7_1
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
QFN - 64
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 002-05631 Rev *B
Page 12 of 128
MB9AB40NB Series
LBC112
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
VSS
UDP0
UDM0
VCC
P0E
P0B
AN22
TMS/
SWDIO
TRSTX
VCC
VSS
B
VCC
VSS
P52
P61
P0F
P0C
AN23
TDO/
SWO
TCK/
SWCLK
VSS
TDI
C
P50
P51
VSS
P60
P62
P0D
P09
AN20
VSS
AN19
AN18
D
P53
P54
P55
VSS
P56
P63
P0A
VSS
AN21
AN16
AN15
E
P30
P31
P32
P33
Index
AN17
AN14
AN12
AN11
F
P34
P35
P36
P39
AN13
AN10
AN09
AVRH
G
P37
P38
P3A
P3D
AN08
AN07
AN06
AVSS
H
P3B
P3C
P3E
VSS
P44
P4C
AN05
VSS
AN04
AN03
AVCC
J
VCC
P3F
VSS
P40
P43
P49
P4D
AN02
VSS
AN01
AN00
K
VCC
VSS
X1A
INITX
P42
P48
P4B
P4E
MD1
VSS
VCC
L
VSS
C
X0A
VSS
P41
P45
P4A
MD0
X0
X1
VSS
PFBGA - 112
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
Document Number: 002-05631 Rev *B
Page 13 of 128
MB9AB40NB Series
FDG096
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
VSS
UDP0
UDM0
VCC
VSS
P0F
VSS
AN22
TMS/
SWDIO
TRSTX
VSS
B
VCC
VSS
P52
P61
P63
P0D
P0C
TDO/
SWO
TCK/
SWCLK
VSS
TDI
C
P50
P51
VSS
P60
P62
P0E
P0B
P0A
VSS
AN19
AN18
D
P53
P54
P55
Index
AN17
AN16
VSS
E
P56
P30
P31
AN11
AN10
AN09
F
VSS
VSS
VSS
AN08
AN07
AVRH
G
P32
P33
P39
AN06
AN05
AVSS
H
P3A
P3B
P3C
AN04
AN03
AVCC
J
P3D
P3E
VSS
P3F
P48
P4A
P4D
AN02
VSS
AN01
AN00
K
VCC
VSS
X1A
INITX
P45
P49
P4C
P4E
MD1
VSS
VCC
L
VSS
C
X0A
VSS
P44
VSS
P4B
MD0
X0
X1
VSS
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For
these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function
register (EPFR) to select the pin.
PFBGA - 96
Document Number: 002-05631 Rev *B
Page 14 of 128
MB9AB40NB Series
4.
List of Pin Functions
4.1
List of Pin Numbers
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR)
to select the pin.
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
1
79
B1
1
B1
2
80
C1
2
C1
LQFP-64
QFN-64
1
2
-
3
81
C2
3
C2
-
-
-
-
-
-
3
4
82
B3
4
B3
-
-
-
-
-
-
4
5
83
D1
5
D1
-
6
84
D2
6
D2
-
Document Number: 002-05631 Rev *B
I/O
Circuit
Type
Pin Name
VCC
P50
INT00_0
SIN3_1
VV4
MADATA00_1
P51
INT01_0
SOT3_1 (SDA3_1)
VV3
MADATA01_1
P51
INT01_0
SOT3_1 (SDA3_1)
P52
INT02_0
SCK3_1 (SCL3_1)
VV2
MADATA02_1
P52
INT02_0
SCK3_1 (SCL3_1)
P53
SIN6_0
TIOA1_2
INT07_2
VV1
MADATA03_1
P54
SOT6_0 (SDA6_0)
TIOB1_2
VV0
MADATA04_1
Pin State
Type
-
J
Y
J
Y
E
L
J
Y
E
L
J
Y
J
X
Page 15 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP-64
QFN-64
7
85
D3
7
D3
-
8
86
D5
8
E1
-
9
87
E1
9
E2
5
-
10
88
E2
10
E3
6
-
11
89
E3
11
G1
7
-
12
90
E4
12
G2
8
13
91
F1
-
-
-
14
92
F2
-
-
-
Pin Name
P55
SCK6_0 (SCL6_0)
ADTG_1
SEG39
MADATA05_1
P56
INT08_2
SEG38
MADATA06_1
P30
TIOB0_1
INT03_2
COM7
MADATA07_1
P31
TIOB1_1
SCK6_1 (SCL6_1)
INT04_2
COM6
MADATA08_1
P32
TIOB2_1
SOT6_1 (SDA6_1)
INT05_2
COM5
MADATA09_1
P33
INT04_0
TIOB3_1
SIN6_1
ADTG_6
COM4
MADATA10_1
P34
TIOB4_1
MADATA11_1
P35
TIOB5_1
INT08_1
I/O
Circuit
Type
Pin State
Type
K
U
K
V
K
V
K
V
K
V
K
V
E
K
E
L
MADATA12_1
Document Number: 002-05631 Rev *B
Page 16 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP-64
QFN-64
15
93
F3
-
-
-
-
-
-
-
F1
F2
F3
-
16
94
G1
-
-
-
17
95
G2
-
-
-
18
96
F4
13
G3
9
19
97
G3
14
H1
10
20
98
H1
15
H2
11
21
99
H2
16
H3
12
22
100
G4
17
J1
13
-
-
B2
-
B2
-
23
1
H3
18
J2
14
24
2
J2
19
J4
15
25
26
3
4
L1
J1
20
-
L1
-
16
-
Document Number: 002-05631 Rev *B
I/O
Circuit
Type
Pin Name
P36
SIN5_2
INT09_1
MADATA13_1
VSS
VSS
VSS
P37
SOT5_2 (SDA5_2)
INT10_1
MADATA14_1
P38
SCK5_2 (SCL5_2)
INT11_1
MADATA15_1
P39
ADTG_2
COM3
P3A
TIOA0_1
RTCCO_2
SUBOUT_2
COM2
P3B
TIOA1_1
COM1
P3C
TIOA2_1
COM0
P3D
TIOA3_1
SEG37
VSS
P3E
TIOA4_1
SEG36
P3F
TIOA5_1
SEG35
VSS
VCC
E
Pin State
Type
L
-
E
L
E
L
K
U
K
U
K
U
K
U
K
U
K
U
K
U
-
Page 17 of 128
MB9AB40NB Series
Pin No
BGA-96
LQFP-64
QFN-64
LQFP-100
QFP-100
BGA-112
LQFP-80
27
5
J4
-
-
-
28
6
L5
-
-
-
29
7
K5
-
-
-
30
8
J5
-
-
-
31
9
H5
21
L5
-
32
10
L6
22
K5
-
33
34
35
11
12
13
K2
J3
H4
L2
L4
K1
23
24
25
K2
J3
L6
L2
L4
K1
17
18
36
14
L3
26
L3
19
37
15
K3
27
K3
20
38
16
K4
28
K4
21
39
17
K6
29
J5
-
22
40
18
J6
30
K6
-
Document Number: 002-05631 Rev *B
Pin Name
P40
TIOA0_0
INT12_1
P41
TIOA1_0
INT13_1
P42
TIOA2_0
P43
TIOA3_0
ADTG_7
P44
TIOA4_0
SEG34
MAD00_1
P45
TIOA5_0
SEG33
MAD01_1
VSS
VSS
VSS
VSS
C
VSS
VCC
P46
X0A
P47
X1A
INITX
P48
INT14_1
SIN3_2
SEG32
MAD02_1
P49
TIOB0_0
SEG31
SOT3_2
(SDA3_2)
MAD03_1
I/O Circuit
Type
Pin State
Type
E
L
E
L
E
K
E
K
K
U
K
U
D
F
D
G
B
C
K
V
K
U
Page 18 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP-64
QFN-64
23
41
19
L7
31
J6
-
42
20
K7
32
L7
24
-
43
21
H6
33
K7
25
-
44
22
J7
34
J7
26
-
45
23
K8
35
K8
27
46
24
K9
36
K9
28
47
25
L8
37
L8
29
48
26
L9
38
L9
30
49
27
L10
39
L10
31
50
51
28
29
L11
K11
40
41
L11
K11
32
33
52
30
J11
42
J11
34
53
31
J10
43
J10
35
-
Document Number: 002-05631 Rev *B
Pin Name
P4A
TIOB1_0
SEG30
SCK3_2 (SCL3_2)
MAD04_1
P4B
TIOB2_0
SEG29
MAD05_1
P4C
TIOB3_0
SCK7_1 (SCL7_1)
CEC0
MAD06_1
P4D
TIOB4_0
SOT7_1 SDA7_1)
MAD07_1
P4E
TIOB5_0
INT06_2
SIN7_1
MAD08_1
MD1
PE0
MD0
X0
PE2
X1
PE3
VSS
VCC
P10
AN00
SEG28
P11
AN01
SIN1_1
INT02_1
WKUP1
SEG27
MAD09_1
I/O Circuit
Type
Pin State
Type
K
U
K
U
I*
S
I*
K
I*
L
C
E
G
D
A
A
A
B
L
W
L
R
Page 19 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-10
0
BGA-112
LQFP-80
BGA-96
54
32
J8
44
J8
-
-
K10
J9
-
K10
J9
55
33
H10
45
H10
LQFP-64
QFN-64
36
-
37
-
38
56
34
H9
46
H9
-
39
57
35
H7
47
G10
-
58
36
G10
48
G9
59
37
G9
49
F10
60
61
62
38
39
40
H11
F11
G11
50
51
52
H11
F11
G11
Document Number: 002-05631 Rev *B
-
40
41
42
43
I/O
Circuit
Type
Pin Name
P12
AN02
SOT1_1.(SDA1_1)
SEG26
MAD10_1
VSS
VSS
P13
AN03
SCK1_1 (SCL1_1)
RTCCO_1
SEG25
SUBOUT_1
MAD11_1
P14
AN04
INT03_1
SEG24
SIN0_1
MAD12_1
P15
AN05
SEG23
SOT0_1 (SDA0_1)
MAD13_1
P16
AN06
SCK0_1 (SCL0_1)
SEG22
MAD14_1
P17
AN07
SIN2_2
INT04_1
SEG21
MAD15_1
AVCC
AVRH
AVSS
L
Pin State
Type
W
-
L
W
L
N
L
W
L
W
L
N
-
Page 20 of 128
MB9AB40NB Series
Pin No
LQFP-100
63
QFP-100
41
BGA-112
G8
LQFP-80
53
BGA-96
F9
LQFP-64
QFN-64
44
-
45
64
42
F10
54
E11
-
-
H8
-
-
-
65
43
F9
55
E10
-
66
44
E11
56
E9
-
67
45
E10
-
-
-
68
46
F8
-
-
-
69
47
E9
-
-
-
70
48
D11
-
-
-
Document Number: 002-05631 Rev *B
I/O
Circuit
Type
Pin Name
P18
AN08
SOT2_2 (SDA2_2)
SEG20
MAD16_1
P19
AN09
SCK2_2 (SCL2_2)
SEG19
MAD17_1
VSS
P1A
AN10
SIN4_1
INT05_1
SEG18
MAD18_1
P1B
AN11
SOT4_1 (SDA4_1)
SEG17
MAD19_1
P1C
AN12
SCK4_1 (SCL4_1)
SEG16
MAD20_1
P1D
AN13
CTS4_1
SEG15
MAD21_1
P1E
AN14
RTS4_1
SEG14
MAD22_1
P1F
AN15
ADTG_5
MAD23_1
pin state
type
L
W
L
W
-
L
N
L
W
L
W
L
W
L
W
F
M
Page 21 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
-
-
B10
C9
-
-
B10
C9
D11
LQFP-64
QFN-64
-
71
49
D10
57
D10
46
72
50
E8
58
D9
47
73
51
C11
59
C11
48
74
52
C10
60
C10
-
75
76
53
54
A11
A10
-
A11
-
-
77
55
A9
61
A10
BGA-96
49
-
78
56
B9
62
B9
79
57
B11
63
B11
50
51
-
80
81
58
59
A8
64
A9
52
B8
65
B8
53
Document Number: 002-05631 Rev *B
Pin Name
VSS
VSS
VSS
P23
AN16
SCK0_0 (SCL0_0)
TIOA7_1
SEG13
P22
AN17
SOT0_0 (SDA0_0)
TIOB7_1
SEG12
P21
AN18
SIN0_0
INT06_1
WKUP2
SEG11
P20
AN19
INT05_0
CROUT_0
SEG10
MAD24_1
VSS
VCC
P00
TRSTX
MCSX7_1
P01
TCK
SWCLK
P02
TDI
MCSX6_1
P03
TMS
SWDIO
P04
TDO
SWO
I/O Circuit
Type
Pin State
Type
-
L
W
L
W
L
R
L
N
E
J
E
J
E
J
E
J
E
J
Page 22 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP-64
QFN-64
82
60
C8
-
-
-
-
-
D8
-
-
-
83
61
D9
-
-
-
66
A8
84
62
A7
-
-
-
-
-
-
-
A7
-
85
63
B7
-
-
-
86
64
C7
-
-
-
87
65
D7
67
C8
54
-
Document Number: 002-05631 Rev *B
I/O
Circuit
Type
Pin Name
P05
AN20
TRACED0
TIOA5_2
SIN4_2
INT00_1
SEG09
MCSX5_1
VSS
P06
AN21
TRACED1
TIOB5_2
SOT4_2 (SDA4_2)
INT01_1
SEG08
MCSX4_1
P07
AN22
ADTG_0
SEG07
MCLKOUT_1
TRACED2
SCK4_2 (SCL4_2)
VSS
P08
AN23
TRACED3
TIOA0_2
CTS4_2
SEG06
MCSX3_1
P09
TRACECLK
TIOB0_2
RTS4_2
SEG05
MCSX2_1
P0A
SIN4_0
INT00_2
MCSX1_1
L
Pin State
Type
Q
-
L
Q
L
P
-
L
P
K
O
I*
L
Page 23 of 128
MB9AB40NB Series
Pin No
LQFP-100
88
QFP-100
66
BGA-112
A6
LQFP-80
68
BGA-96
C7
LQFP-64
QFN-64
55
56
89
67
B6
69
B7
-
-
D4
C3
-
C3
-
90
68
C6
70
B6
-
91
69
A5
71
C6
-
-
-
-
-
A5
-
92
70
B5
72
A6
57
93
71
D6
73
B5
-
94
72
C5
74
C5
58
-
95
73
B4
Document Number: 002-05631 Rev *B
75
B4
59
I/O
Circuit
Type
Pin Name
P0B
SOT4_0 (SDA4_0)
TIOB6_1
MCSX0_1
P0C
SCK4_0 (SCL4_0)
TIOA6_1
MALE_1
VSS
VSS
P0D
RTS4_0
TIOA3_2
SEG04
MDQM0_1
P0E
CTS4_0
TIOB3_2
SEG03
MDQM1_1
VSS
P0F
NMIX
CROUT_1
RTCCO_0
SUBOUT_0
WKUP0
P63
INT03_0
SEG02
MWEX_1
P62
SCK5_0 (SCL5_0)
ADTG_3
SEG01
MOEX_1
P61
SOT5_0 (SDA5_0)
TIOB2_2
UHCONX
SEG00
Pin State
Type
I*
K
I*
K
-
K
U
K
U
-
E
I
K
V
K
U
K
U
Page 24 of 128
MB9AB40NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP-64
QFN-64
60
96
74
C4
76
C4
97
75
A4
77
A4
61
98
76
A3
78
A3
62
99
77
A2
79
A2
63
100
78
A1
80
A1
64
I/O
Circuit
Type
Pin Name
P60
SIN5_0
TIOA2_2
INT15_1
WKUP3
CEC1
MRDY_1
VCC
P80
UDM0
P81
UDP0
VSS
I*
Pin State
Type
T
H
H
H
H
-
-
*: 5 V tolerant I/O
Document Number: 002-05631 Rev *B
Page 25 of 128
MB9AB40NB Series
4.2
List of Pin Functions
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR)
to select the pin.
Pin
Function
ADC
Pin No
Pin Name
ADTG_0
ADTG_1
ADTG_2
ADTG_3
ADTG_4
ADTG_5
ADTG_6
ADTG_7
ADTG_8
AN00
AN01
AN02
AN03
AN04
AN05
AN06
AN07
AN08
AN09
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
Function Description
A/D converter external
trigger input pin
A/D converter analog
input pin.
ANxx describes ADC
ch.xx.
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
84
7
18
94
70
12
30
52
53
54
55
56
57
58
59
63
64
65
66
67
68
69
70
71
72
73
74
82
83
84
85
62
85
96
72
48
90
8
30
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
49
50
51
52
60
61
62
63
A7
D3
F4
C5
D11
E4
J5
J11
J10
J8
H10
H9
H7
G10
G9
G8
F10
F9
E11
E10
F8
E9
D11
D10
E8
C11
C10
C8
D9
A7
B7
66
7
13
74
12
42
43
44
45
46
47
48
49
53
54
55
56
57
58
59
60
66
-
A8
D3
G3
C5
G2
J11
J10
J8
H10
H9
G10
G9
F10
F9
E11
E10
E9
D10
D9
C11
C10
A8
-
LQFP/
QFN-64
9
58
8
34
35
36
37
38
39
40
44
45
46
47
48
-
Page 26 of 128
MB9AB40NB Series
Pin
Function
Base
Timer 0
Base
Timer 1
Base
Timer 2
Base
Timer 3
Base
Timer
4
Base
Timer 5
Base
Timer 6
Pin No
Pin Name
TIOA0_0
TIOA0_1
TIOA0_2
TIOB0_0
TIOB0_1
TIOB0_2
TIOA1_0
TIOA1_1
TIOA1_2
TIOB1_0
TIOB1_1
TIOB1_2
TIOA2_0
TIOA2_1
TIOA2_2
TIOB2_0
TIOB2_1
TIOB2_2
TIOA3_0
TIOA3_1
TIOA3_2
TIOB3_0
TIOB3_1
TIOB3_2
TIOA4_0
TIOA4_1
TIOA4_2
TIOB4_0
TIOB4_1
TIOB4_2
TIOA5_0
TIOA5_1
TIOA5_2
TIOB5_0
TIOB5_1
TIOB5_2
TIOA6_1
TIOB6_1
Base
Timer 7
TIOA7_0
TIOA7_1
TIOA7_2
TIOB7_0
TIOB7_1
TIOB7_2
Function Description
Base timer ch.0 TIOA
pin
Base timer ch.0 TIOB
pin
Base timer ch.1 TIOA
pin
Base timer ch.1 TIOB
pin
Base timer ch.2 TIOA
pin
Base timer ch.2 TIOB
pin
Base timer ch.3 TIOA
pin
Base timer ch.3 TIOB
pin
Base timer ch.4 TIOA
pin
Base timer ch.4 TIOB
pin
Base timer ch.5 TIOA
pin
Base timer ch.5 TIOB
pin
Base timer ch.6 TIOA
pin
Base timer ch.6 TIOB
pin
Base timer ch.7 TIOA
pin
Base timer ch.7 TIOB
pin
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
27
19
85
40
9
86
28
20
5
41
10
6
29
21
96
42
11
95
30
22
90
43
12
91
31
23
44
13
32
24
82
45
14
83
5
97
63
18
87
64
6
98
83
19
88
84
7
99
74
20
89
73
8
100
68
21
90
69
9
1
22
91
10
2
60
23
92
61
J4
G3
B7
J6
E1
C7
L5
H1
D1
L7
E2
D2
K5
H2
C4
K7
E3
B4
J5
G4
C6
H6
E4
A5
H5
H3
J7
F1
L6
J2
C8
K8
F2
D9
14
30
9
15
5
31
10
6
16
76
32
11
75
17
70
33
12
71
21
18
34
22
19
35
-
H1
K6
E2
H2
D1
J6
E3
D2
H3
C4
L7
G1
B4
J1
B6
K7
G2
C6
L5
J2
J7
K5
J4
K8
-
LQFP/
QFN-64
10
22
5
11
23
6
12
60
24
7
59
13
25
8
14
26
15
27
-
89
67
B6
69
B7
56
88
66
A6
68
C7
55
71
72
-
49
50
-
D10
E8
-
57
58
-
D10
D9
-
46
47
-
Page 27 of 128
MB9AB40NB Series
Pin
Function
Debugger
Pin No
Pin Name
SWCLK
SWDIO
SWO
TCK
TDI
TDO
TMS
TRACECL
K
TRACED0
TRACED1
TRACED2
TRACED3
TRSTX
External
Bus
MAD00_1
MAD01_1
MAD02_1
MAD03_1
MAD04_1
MAD05_1
MAD06_1
MAD07_1
MAD08_1
MAD09_1
MAD10_1
MAD11_1
MAD12_1
MAD13_1
MAD14_1
MAD15_1
MAD16_1
MAD17_1
MAD18_1
MAD19_1
MAD20_1
MAD21_1
MAD22_1
MAD23_1
MAD24_1
Function Description
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
78
56
B9
62
B9
50
80
58
A8
64
A9
52
81
59
B8
65
B8
53
78
56
B9
62
B9
50
79
57
B11
63
B11
51
81
59
B8
65
B8
53
80
58
A8
64
A9
52
86
64
C7
-
-
-
Trace data output pins
of ETM
82
83
84
85
60
61
62
63
C8
D9
A7
B7
-
-
-
JTAG test reset Input
pin
77
55
A9
61
A10
49
External bus interface
address bus
31
32
39
40
41
42
43
44
45
53
54
55
56
57
58
59
63
64
65
66
67
68
69
70
74
9
10
17
18
19
20
21
22
23
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
52
H5
L6
K6
J6
L7
K7
H6
J7
K8
J10
J8
H10
H9
H7
G10
G9
G8
F10
F9
E11
E10
F8
E9
D11
C10
21
22
29
30
31
32
33
34
35
43
44
45
46
47
48
49
53
54
55
56
60
L5
K5
J5
K6
J6
L7
K7
J7
K8
J10
J8
H10
H9
G10
G9
F10
F9
E11
E10
E9
C10
-
Serial wire debug
interface clock input pin
Serial wire debug
interface data input /
output pin
Serial wire viewer
output pin
JTAG test clock input
pin
JTAG test data input
pin
JTAG debug data
output pin
JTAG test mode state
input/output pin
Trace CLK output pin
of ETM
Document Number: 002-05631 Rev *B
Page 28 of 128
MB9AB40NB Series
Pin
Function
External
Bus
Pin Name
MCSX0_1
MCSX1_1
MCSX2_1
MCSX3_1
MCSX4_1
MCSX5_1
MCSX6_1
MCSX7_1
MDQM0_1
MDQM1_1
MOEX_1
MWEX_1
MADATA00_1
MADATA01_1
MADATA02_1
MADATA03_1
MADATA04_1
MADATA05_1
MADATA06_1
MADATA07_1
MADATA08_1
MADATA09_1
MADATA10_1
MADATA11_1
MADATA12_1
MADATA13_1
MADATA14_1
MADATA15_1
MALE_1
MRDY_1
MCLKOUT_1
Function
Description
External bus
interface chip select
output pin
External bus
interface byte mask
signal output pin
External bus
interface read
enable signal for
SRAM
External bus
interface write
enable signal for
SRAM
External bus interface
data bus
Address Latch
enable signal for
multiplex
External bus RDY
input signal
External bus clock
output pin
Document Number: 002-05631 Rev *B
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
88
87
86
85
83
82
79
77
90
66
65
64
63
61
60
57
55
68
A6
D7
C7
B7
D9
C8
B11
A9
C6
68
67
63
61
70
C7
C8
B11
A10
B6
LQFP/
QFN-64
-
91
69
A5
71
C6
-
94
72
C5
74
C5
-
93
71
D6
73
B5
-
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
C1
C2
B3
D1
D2
D3
D5
E1
E2
E3
E4
F1
F2
F3
G1
G2
2
3
4
5
6
7
8
9
10
11
12
-
C1
C2
B3
D1
D2
D3
E1
E2
E3
G1
G2
-
-
89
67
B6
69
B7
-
96
74
C4
76
C4
-
84
62
A7
66
A8
-
Page 29 of 128
MB9AB40NB Series
Pin
Function
External
Interrupt
Pin No
Pin Name
INT00_0
INT00_1
INT00_2
INT01_0
INT01_1
INT02_0
INT02_1
INT03_0
INT03_1
INT03_2
INT04_0
INT04_1
INT04_2
INT05_0
INT05_1
INT05_2
INT06_1
INT06_2
INT07_2
INT08_1
INT08_2
INT09_1
INT10_1
INT11_1
INT12_1
INT13_1
INT14_1
INT15_1
NMIX
Function Description
External interrupt
request 00 input pin
External interrupt
request 01 input pin
External interrupt
request 02 input pin
External interrupt
request 03 input pin
External interrupt
request 04 input pin
External interrupt
request 05 input pin
External interrupt
request 06 input pin
External interrupt
request 07 input pin
External interrupt
request 08 input pin
External interrupt
request 09 input pin
External interrupt
request 10 input pin
External interrupt
request 11 input pin
External interrupt
request 12 input pin
External interrupt
request 13 input pin
External interrupt
request 14 input pin
External interrupt
request 15 input pin
Non-Maskable Interrupt
input pin
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
2
82
87
3
83
4
53
93
56
9
12
59
10
74
65
11
73
45
80
60
65
81
61
82
31
71
34
87
90
37
88
52
43
89
51
23
C1
C8
D7
C2
D9
B3
J10
D6
H9
E1
E4
G9
E2
C10
F9
E3
C11
K8
2
67
3
4
43
73
46
9
12
49
10
60
55
11
59
35
C1
C8
C2
B3
J10
B5
H9
E2
G2
F10
E3
C10
E10
G1
C11
K8
LQFP/
QFN-64
2
54
3
4
35
38
5
8
40
6
7
48
27
5
83
D1
5
D1
-
14
8
92
86
F2
D5
8
E1
-
15
93
F3
-
-
-
16
94
G1
-
-
-
17
95
G2
-
-
-
27
5
J4
-
-
-
28
6
L5
-
-
-
39
17
K6
29
J5
-
96
74
C4
76
C4
60
92
70
B5
72
A6
57
Page 30 of 128
MB9AB40NB Series
Pin
Function
GPIO
Pin
Name
P00
P01
P02
P03
P04
P05
P06
P07
P08
P09
P0A
P0B
P0C
P0D
P0E
P0F
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P1A
P1B
P1C
P1D
P1E
P1F
P20
P21
P22
P23
Pin No
Function Description
General-purpose I/O
port 0
General-purpose I/O
port 1
General-purpose I/O
port 2
Document Number: 002-05631 Rev *B
LQFP-100
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
52
53
54
55
56
57
58
59
63
64
65
66
67
68
69
70
74
73
72
71
QFP-100
BGA-112
LQFP-80
BGA-96
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
30
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
52
51
50
49
A9
B9
B11
A8
B8
C8
D9
A7
B7
C7
D7
A6
B6
C6
A5
B5
J11
J10
J8
H10
H9
H7
G10
G9
G8
F10
F9
E11
E10
F8
E9
D11
C10
C11
E8
D10
61
62
63
64
65
66
67
68
69
70
71
72
42
43
44
45
46
47
48
49
53
54
55
56
60
59
58
57
A10
B9
B11
A9
B8
A8
C8
C7
B7
B6
C6
A6
J11
J10
J8
H10
H9
G10
G9
F10
F9
E11
E10
E9
C10
C11
D9
D10
LQFP/
QFN-64
49
50
51
52
53
54
55
56
57
34
35
36
37
38
39
40
44
45
48
47
46
Page 31 of 128
MB9AB40NB Series
Pin
Function
GPIO
Pin
Name
P30
P31
P32
P33
P34
P35
P36
P37
P38
P39
P3A
P3B
P3C
P3D
P3E
P3F
P40
P41
P42
P43
P44
P45
P46
P47
P48
P49
P4A
P4B
P4C
P4D
P4E
P50
P51
P52
P53
P54
P55
P56
P60
P61
P62
P63
P80
P81
PE0
PE2
PE3
Pin No
Function Description
General-purpose I/O
port 3
General-purpose I/O
port 4
General-purpose I/O
port 5
General-purpose I/O
port 6
General-purpose I/O
port 8
General-purpose I/O
port E
Document Number: 002-05631 Rev *B
LQFP-100
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
27
28
29
30
31
32
36
37
39
40
41
42
43
44
45
2
3
4
5
6
7
8
96
95
94
93
98
99
46
48
49
QFP-100
BGA-112
LQFP-80
BGA-96
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
2
5
6
7
8
9
10
14
15
17
18
19
20
21
22
23
80
81
82
83
84
85
86
74
73
72
71
76
77
24
26
27
E1
E2
E3
E4
F1
F2
F3
G1
G2
F4
G3
H1
H2
G4
H3
J2
J4
L5
K5
J5
H5
L6
L3
K3
K6
J6
L7
K7
H6
J7
K8
C1
C2
B3
D1
D2
D3
D5
C4
B4
C5
D6
A3
A2
K9
L9
L10
9
10
11
12
13
14
15
16
17
18
19
21
22
26
27
29
30
31
32
33
34
35
2
3
4
5
6
7
8
76
75
74
73
78
79
36
38
39
E2
E3
G1
G2
G3
H1
H2
H3
J1
J2
J4
L5
K5
L3
K3
J5
K6
J6
L7
K7
J7
K8
C1
C2
B3
D1
D2
D3
E1
C4
B4
C5
B5
A3
A2
K9
L9
L10
LQFP/
QFN-64
5
6
7
8
9
10
11
12
13
14
15
19
20
22
23
24
25
26
27
2
3
4
60
59
58
62
63
28
30
31
Page 32 of 128
MB9AB40NB Series
Pin
Function
Multifunction
Serial0
Pin No
Pin Name
Function Description
SIN0_0
Multi-function serial
interface ch.0 input pin
SIN0_1
SOT0_0
(SDA0_0)
SOT0_1
(SDA0_1)
SCK0_0
(SCL0_0)
SCK0_1
(SCL0_1)
Multifunction
Serial1
SIN1_1
SOT1_1
(SDA1_1)
SCK1_1
(SCL1_1)
Multi-function serial
interface ch.0 output
pin.
This pin operates as
SOT0 when it is used
in a UART/CSIO
(operation modes 0 to
2) and as SDA0 when
it is used in an I2C
(operation mode 4).
Multi-function serial
interface ch.0 clock I/O
pin.
This pin operates as
SCK0 when it is used
in a UART/CSIO
(operation modes 0 to
2) and as SCL0 when it
is used in an I2C
(operation mode 4).
Multi-function serial
interface ch.1 input pin
Multi-function serial
interface ch.1 output
pin.
This pin operates as
SOT1 when it is used
in a UART/CSIO
(operation modes 0 to
2) and as SDA1 when
it is used in an I2C
(operation mode 4).
Multi-function serial
interface ch.1 clock I/O
pin.
This pin operates as
SCK1 when it is used
in a UART/CSIO
(operation modes 0 to
2) and as SCL1 when it
is used in an I2C
(operation mode 4).
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
73
51
C11
59
C11
LQFP/
QFN-64
48
56
34
H9
46
H9
-
72
50
E8
58
D9
47
57
35
H7
47
G10
-
71
49
D10
57
D10
46
58
36
G10
48
G9
-
53
31
J10
43
J10
35
54
32
J8
44
J8
36
55
33
H10
45
H10
37
Page 33 of 128
MB9AB40NB Series
Pin No
Pin
Function
Multifunction
Serial
2
Pin Name
SIN2_2
SOT2_2
(SDA2_2)
SCK2_2
(SCL2_2)
Multifunction
Serial
3
SIN3_1
SIN3_2
SOT3_1
(SDA3_1)
SOT3_2
(SDA3_2)
SCK3_1
(SCL3_1)
SCK3_2
(SCL3_2)
Function Description
Multi-function serial
interface ch.2 input pin
Multi-function serial
interface ch.2 output pin.
This pin operates as
SOT2 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SDA2 when it is
used in an I2C (operation
mode 4).
Multi-function serial
interface ch.2 clock I/O
pin.
This pin operates as
SCK2 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SCL2 when it is
used in an I2C (operation
mode 4).
Multi-function serial
interface ch.3 input pin
Multi-function serial
interface ch.3 output pin.
This pin operates as
SOT3 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SDA3 when it is
used in an I2C (operation
mode 4).
Multi-function serial
interface ch.3 clock I/O
pin.
This pin operates as
SCK3 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SCL3 when it is
used in an I2C (operation
mode 4).
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-6
4
59
37
G9
49
F10
40
63
41
G8
53
F9
44
64
42
F10
54
E11
45
2
80
C1
2
C1
2
39
17
K6
29
J5
-
3
81
C2
3
C2
3
40
18
J6
30
K6
-
4
82
B3
4
B3
4
41
19
L7
31
J6
-
Page 34 of 128
MB9AB40NB Series
Pin
Function
Multifunction
Serial
4
Pin No
Pin Name
SIN4_0
SIN4_1
Multi-function serial
interface ch.4 input pin
SIN4_2
SOT4_0
(SDA4_0)
SOT4_1
(SDA4_1)
SOT4_2
(SDA4_2)
SCK4_0
(SCL4_0)
SCK4_1
(SCL4_1)
SCK4_2
(SCL4_2)
RTS4_0
RTS4_1
RTS4_2
CTS4_0
CTS4_1
CTS4_2
Multifunction
Serial
5
Function Description
SIN5_0
SIN5_2
SOT5_0
(SDA5_0)
SOT5_2
(SDA5_2)
SCK5_0
(SCL5_0)
SCK5_2
(SCL5_2)
Multi-function serial
interface ch.4 output pin.
This pin operates as
SOT4 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SDA4 when it is
used in an I2C (operation
mode 4).
Multi-function serial
interface ch.4 clock I/O
pin.
This pin operates as
SCK4 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SCL4 when it is
used in an I2C (operation
mode 4).
Multi-function serial
interface ch.4 RTS
output pin
Multi-function serial
interface ch.4 CTS input
pin
Multi-function serial
interface ch.5 input pin
Multi-function serial
interface ch.5 output pin.
This pin operates as
SOT5 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SDA5 when it is
used in an I2C (operation
mode 4).
Multi-function serial
interface ch.5 clock I/O
pin.
This pin operates as
SCK5 when it is used in
a UART/CSIO
(operation modes 0 to 2)
and as SCL5 when it is
used in an I2C (operation
mode 4).
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
87
65
D7
67
C8
54
65
43
F9
55
E10
-
82
60
C8
-
-
-
88
66
A6
68
C7
55
66
44
E11
56
E9
-
83
61
D9
-
-
-
89
67
B6
69
B7
56
67
45
E10
-
-
-
84
62
A7
-
-
-
90
68
C6
70
B6
-
69
47
E9
-
-
-
86
64
C7
-
-
-
91
69
A5
71
C6
-
68
46
F8
-
-
-
85
63
B7
-
-
-
96
74
C4
76
C4
60
15
93
F3
-
-
-
95
73
B4
75
B4
59
16
94
G1
-
-
-
94
72
C5
74
C5
58
17
95
G2
-
-
-
Page 35 of 128
MB9AB40NB Series
Pin
Function
Multifunction
Serial
6
Pin No
Pin Name
SIN6_0
SIN6_1
SOT6_0
(SDA6_0)
SOT6_1
(SDA6_1)
SCK6_0
(SCL6_0)
SCK6_1
(SCL6_1)
Multifunction
Serial
7
SIN7_1
SOT7_1
(SDA7_1)
SCK7_1
(SCL7_1)
Function Description
Multi-function serial
interface ch.6 input pin
Multi-function serial
interface ch.6 output pin.
This pin operates as
SOT6 when it is used in a
UART/CSIO (operation
modes 0 to 2) and as
SDA6 when it is used in
an I2C (operation mode
4).
Multi-function serial
interface ch.6 clock I/O
pin.
This pin operates as
SCK6 when it is used in a
UART/CSIO (operation
modes 0 to 2) and as
SCL6 when it is used in
an I2C (operation mode
4).
Multi-function serial
interface ch.7 input pin
Multi-function serial
interface ch.7 output pin.
This pin operates as
SOT7 when it is used in a
UART/CSIO (operation
modes 0 to 2) and as
SDA7 when it is used in
an I2C (operation mode
4).
Multi-function serial
interface ch.7 clock I/O
pin.
This pin operates as
SCK7 when it is used in a
UART/CSIO (operation
modes 0 to 2) and as
SCL7 when it is used in
an I2C (operation mode
4).
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
5
83
D1
5
D1
LQFP/
QFN-64
-
12
90
E4
12
G2
8
6
84
D2
6
D2
-
11
89
E3
11
G1
7
7
85
D3
7
D3
-
10
88
E2
10
E3
6
45
23
K8
35
K8
27
44
22
J7
34
J7
26
43
21
H6
33
K7
25
Page 36 of 128
MB9AB40NB Series
Pin
Function
USB
Pin Name
UDM0
UDP0
UHCONX
Real-time
clock
Low-Power
Consumption
Mode
RTCCO_0
RTCCO_1
RTCCO_2
SUBOUT_0
SUBOUT_1
SUBOUT_2
WKUP0
WKUP1
WKUP2
WKUP3
HDMICEC/
Remote
Control
Reception
LCDC
Function
Description
USB device/host D
– pin
USB device/host D
+ pin
USB external pull-up
control pin
0.5 seconds pulse
output pin of
Real-time clock
Sub clock output pin
Deep standby mode
return signal input
pin 0
Deep standby mode
return signal input
pin 1
Deep standby mode
return signal input
pin 2
Deep standby mode
return signal input
pin 3
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
98
76
A3
78
A3
62
99
77
A2
79
A2
63
95
73
B4
75
B4
59
92
55
19
92
55
19
70
33
97
70
33
97
B5
H10
G3
B5
H10
G3
72
45
14
72
45
14
A6
H10
H1
A6
H10
H1
57
37
10
57
37
10
92
70
B5
72
A6
57
53
31
J10
43
J10
35
73
51
C11
59
C11
48
96
74
C4
76
C4
60
CEC0
HDMI-CEC/Remote
Control Reception
ch.0 input/output pin
43
21
H6
33
K7
25
CEC1
HDMI-CEC/Remote
Control Reception
ch.1 input/output pin
96
74
C4
76
C4
60
6
84
D2
6
D2
-
5
83
D1
5
D1
-
4
82
B3
4
B3
-
VV3
3
81
C2
3
C2
-
VV4
2
80
C1
2
C1
2
COM0
21
99
H2
16
H3
12
COM1
20
98
H1
15
H2
11
COM2
19
97
G3
14
H1
10
18
96
F4
13
G3
9
12
90
E4
12
G2
8
COM5
11
89
E3
11
G1
7
COM6
10
88
E2
10
E3
6
COM7
9
87
E1
9
E2
5
VV0
VV1
VV2
COM3
COM4
LCD drive power
supply pin
LCD common output
pin
Document Number: 002-05631 Rev *B
Page 37 of 128
MB9AB40NB Series
Pin
function
LCDC
Pin name
SEG00
SEG01
SEG02
SEG03
SEG04
SEG05
SEG06
SEG07
SEG08
SEG09
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
Function
description
LCD segment
output pin
Document Number: 002-05631 Rev *B
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
95
94
93
91
90
86
85
84
83
82
74
73
72
71
69
68
67
66
65
64
63
59
58
57
56
55
54
53
52
42
41
40
39
32
31
24
23
22
8
7
73
72
71
69
68
64
63
62
61
60
52
51
50
49
47
46
45
44
43
42
41
37
36
35
34
33
32
31
30
20
19
18
17
10
9
2
1
100
86
85
B4
C5
D6
A5
C6
C7
B7
A7
D9
C8
C10
C11
E8
D10
E9
F8
E10
E11
F9
F10
G8
G9
G10
H7
H9
H10
J8
J10
J11
K7
L7
J6
K6
L6
H5
J2
H3
G4
D5
D3
75
74
73
71
70
66
60
59
58
57
56
55
54
53
49
48
47
46
45
44
43
42
32
31
30
29
22
21
19
18
17
8
7
B4
C5
B5
C6
B6
A8
C10
C11
D9
D10
E9
E10
E11
F9
F10
G9
G10
H9
H10
J8
J10
J11
L7
J6
K6
J5
K5
L5
J4
J2
J1
E1
D3
LQFP/
QFN-64
59
58
48
47
46
45
44
40
39
38
37
36
35
34
24
23
22
15
14
13
-
Page 38 of 128
MB9AB40NB Series
Pin
Function
Pin
Name
Reset
INITX
Mode
MD0
MD1
Pin No
Function Description
External Reset Input pin.
A reset is valid when
INITX=L.
Mode 0 pin.
During normal operation,
MD0=L must be input.
During serial
programming to Flash
memory, MD0=H must be
input.
Mode 1 pin.
During serial
programming to Flash
memory, MD1=L must be
input.
Power
VCC
Power supply Pin
VSS
GND Pin
GND
Document Number: 002-05631 Rev *B
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
38
16
K4
28
K4
21
47
25
L8
37
L8
29
46
24
K9
36
K9
28
1
26
35
51
76
97
25
34
50
75
100
79
4
13
29
54
75
3
12
28
53
78
B1
J1
K1
K11
A10
A4
B2
L1
K2
J3
H4
L4
L11
K10
J9
H8
B10
C9
A11
D8
D4
C3
A1
1
25
41
77
20
24
40
80
B1
K1
K11
A4
F1
F2
F3
B2
L1
K2
J3
L6
L4
L11
K10
J9
B10
C9
D11
A11
A7
C3
A5
A1
1
18
33
61
16
32
64
Page 39 of 128
MB9AB40NB Series
Pin
Function
Clock
Pin No
Pin Name
X0
X0A
X1
X1A
CROUT_0
CROUT_1
ADC
power
AVCC
AVRH
ADC
GND
C pin
Function Description
Main clock (oscillation)
input pin
Sub clock (oscillation)
input pin
Main clock (oscillation)
I/O pin
Sub clock (oscillation)
I/O pin
Built-in high-speed
CR-osc clock output port
A/D converter analog
power supply pin
A/D converter analog
reference voltage input
pin
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
48
26
L9
38
L9
30
36
14
L3
26
L3
19
49
27
L10
39
L10
31
37
15
K3
27
K3
20
74
92
52
70
C10
B5
60
72
C10
A6
57
60
38
H11
50
H11
41
61
39
F11
51
F11
42
AVSS
A/D converter GND pin
62
40
G11
52
G11
43
C
Power supply
stabilization capacity pin
33
11
L2
23
L2
17
Note:
−
While this device contains a Test Access Port (TAP) based on the IEEE 1149.1-2001 JTAG standard, it is not fully compliant
to all requirements of that standard. This device may contain a 32-bit device ID that is the same as the 32-bit device ID in
other devices with different functionality. The TAP pins may also be configurable for purposes other than access to the TAP
controller.
Document Number: 002-05631 Rev *B
Page 40 of 128
MB9AB40NB Series
5.
I/O Circuit Type
Type
Circuit
Remarks
A
It is possible to select the main
oscillation / GPIO function
When the main oscillation is
selected.
Pull-up
resistor
P-ch
−
P-ch
Digital output
−
−
X1
−
−
−
N-ch
Digital output
−
−
R
−
Oscillation feedback resistor:
Approximately 1 MΩ
With Standby mode control
When the GPIO is selected.
CMOS level output.
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor:
Approximately 33 kΩ
IOH= -4 mA, IOL= 4 mA
Pull-up resistor control
Digital input
Standby mode control
Clock input
Feedback
resistor
Standby mode control
Digital input
Standby mode control
Pull-up
resistor
R
P-ch
P-ch
Digital output
N-ch
Digital output
X0
Pull-up resistor control
Document Number: 002-05631 Rev *B
Page 41 of 128
MB9AB40NB Series
Type
Circuit
Remarks
B
−
−
CMOS level hysteresis input
Pull-up resistor: Approximately
33 kΩ
−
−
Open drain output
CMOS level hysteresis input
Pull-up resistor
Digital input
C
Digital input
N-ch
Document Number: 002-05631 Rev *B
Digital output
Page 42 of 128
MB9AB40NB Series
Type
Circuit
Remarks
D
It is possible to select the sub
oscillation / GPIO function
Pull-up
When the sub oscillation is
selected.
resistor
−
P-ch
P-ch
Digital output
−
X1A
Oscillation feedback resistor:
Approximately 5 MΩ
With Standby mode control
When the GPIO is selected.
N-ch
Digital output
R
Pull-up resistor control
−
−
−
−
−
−
CMOS level output.
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
Digital input
Standby mode control
Clock input
Feedback
resistor
Standby mode control
Digital input
Standby mode control
Pull-up
resistor
R
P-ch
P-ch
Digital output
N-ch
Digital output
X0A
Pull-up resistor control
Document Number: 002-05631 Rev *B
Page 43 of 128
MB9AB40NB Series
Type
Circuit
Remarks
E
−
−
−
−
−
P-ch
P-ch
N-ch
Digital output
−
−
CMOS level output
CMOS level hysteresis input
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
When this pin is used as an
I2C pin, the digital output P-ch
transistor is always off
Digital output
R
Pull-up resistor control
Digital input
Standby mode control
F
P-ch
P-ch
Digital output
−
−
−
−
−
−
−
−
−
N-ch
R
CMOS level output
CMOS level hysteresis input
With input control
Analog input
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
Digital output
Pull-up resistor control
Digital input
Standby mode control
Analog input
Input control
Document Number: 002-05631 Rev *B
Page 44 of 128
MB9AB40NB Series
Type
Circuit
Remarks
G
CMOS level hysteresis input
Mode input
H
GPIO Digital output
It is possible to select the USB
I/O / GPIO function.
GPIO Digital input/output direction
When the USB I/O is selected.
GPIO Digital input
GPIO Digital input circuit control
UDP output
UDP0/P81
USB Full-speed/Low-speed control
−
Full-speed, Low-speed control
When the GPIO is selected.
−
−
−
CMOS level output
CMOS level hysteresis input
With standby mode control
−
−
−
−
−
−
CMOS level output
CMOS level hysteresis input
5 V tolerant
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
Available to control PZR
registers.
When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
UDP input
Differential
Differential input
USB/GPIO select
UDM0/P80
UDM input
UDM output
USB Digital input/output direction
GPIO Digital output
GPIO Digital input/output direction
GPIO Digital input
GPIO Digital input circuit control
I
P-ch
P-ch
Digital output
−
−
−
N-ch
Digital output
R
Pull-up resistor control
Digital input
Standby mode control
Document Number: 002-05631 Rev *B
Page 45 of 128
MB9AB40NB Series
Type
Circuit
Remarks
J
P-ch
P-ch
Digital output
−
−
−
−
−
−
−
−
−
N-ch
CMOS level output
CMOS level hysteresis input
With input control
LCD-VV input/output
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
Digital output
Pull-up resistor control
R
Digital input
Standby mode control
LCD VV
input/output
LCD VV control
K
P-ch
P-ch
Digital output
−
−
−
−
−
−
−
−
−
N-ch
R
CMOS level output
CMOS level hysteresis input
With input control
LCD output
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
Digital output
Pull-up resistor control
Digital input
Standby mode control
LCD output
LCD control
Document Number: 002-05631 Rev *B
Page 46 of 128
MB9AB40NB Series
Type
Circuit
Remarks
L
P-ch
P-ch
Digital output
−
−
−
−
−
−
−
−
−
N-ch
R
CMOS level output
CMOS level hysteresis input
With input control
LCD output
With pull-up resistor control
With standby mode control
Pull-up resistor: Approximately
33 kΩ
IOH= -4 mA, IOL= 4 mA
When this pin is used as an
I2C pin, the digital output
P-ch transistor is always off
Digital output
Pull-up resistor control
Digital input
Standby mode control
Analog input
Input control
LCD output
LCD control
Document Number: 002-05631 Rev *B
Page 47 of 128
MB9AB40NB Series
6.
Handling Precautions
Any semiconductor device has inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in
which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed
to minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices.
6.1
Precautions for Product Design
This section describes precautions when designing electronic equipment using semiconductor devices.
Absolute Maximum Ratings
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
certain established limits, called absolute maximum ratings. Do not exceed these ratings.
Recommended Operating Conditions
Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical
characteristics are warranted when operated within these ranges.
Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely
affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users
considering application outside the listed conditions are advised to contact their sales representative beforehand.
Processing and Protection of Pins
These precautions must be followed when handling the pins which connect semiconductor devices to power supply and
input/output functions.
1.
Preventing Over-Voltage and Over-Current Conditions
Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device, and
in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at the
design stage.
2.
Protection of Output Pins
Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows. Such
conditions if present for extended periods of time can damage the device.
Therefore, avoid this type of connection.
3.
Handling of Unused Input Pins
Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be connected
through an appropriate resistance to a power supply pin or ground pin.
Latch-up
Semiconductor devices are constructed by the formation of P-type and N-type areas on a substrate. When subjected to abnormally
high voltages, internal parasitic PNPN junctions (called thyristor structures) may be formed, causing large current levels in
excess of several hundred mA to flow continuously at the power supply pin. This condition is called latch-up.
CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or
damage from high heat, smoke or flame. To prevent this from happening, do the following:
1.
2.
Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to abnormal
noise, surge levels, etc.
Be sure that abnormal current flows do not occur during the power-on sequence.
Observance of Safety Regulations and Standards
Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic
interference, etc. Customers are requested to observe applicable regulations and standards in the design of products.
Document Number: 002-05631 Rev *B
Page 48 of 128
MB9AB40NB Series
Fail-Safe Design
Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
Precautions Related to Usage of Devices
Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office
equipment, industrial, communications, and measurement equipment, personal or household devices, etc.).
CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as
aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.)
are requested to consult with sales representatives before such use. The company will not be responsible for damages arising from
such use without prior approval.
6.2
Precautions for Package Mounting
Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you
should only mount under Cypress's recommended conditions. For detailed information about mount conditions, contact your
sales representative.
Lead Insertion Type
Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board,
or mounting by using a socket.
Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow
soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be
subjected to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to
Cypress recommended mounting conditions.
If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact
deterioration after long periods. For this reason it is recommended that the surface treatment of socket contacts and IC leads be
verified before mounting.
Surface Mount Type
Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily
deformed or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open
connections caused by deformed pins, or shorting due to solder bridges.
You must use appropriate mounting techniques. Cypress Inc. recommends the solder reflow method, and has established a
ranking of mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of
recommended conditions.
Document Number: 002-05631 Rev *B
Page 49 of 128
MB9AB40NB Series
Lead-Free Packaging
CAUTION: When ball grid array (BGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction
strength may be reduced under some conditions of use.
Storage of Semiconductor Devices
Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption
of moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel,
reducing moisture resistance and causing packages to crack. To prevent, do the following:
1.
2.
3.
4.
Avoid exposure to rapid temperature changes, which cause moisture to condense inside the product. Store products in
locations where temperature changes are slight.
Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5°C
and 30°C.
When you open Dry Package that recommends humidity 40% to 70% relative humidity.
When necessary, Cypress Inc. packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a
silica gel desiccant. Devices should be sealed in their aluminum laminate bags for storage.
Avoid storing packages where they are exposed to corrosive gases or high levels of dust.
Baking
Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended
conditions for baking.
Condition: 125°C/24 h
Static Electricity
Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following
precautions:
1.
2.
3.
4.
5.
Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion generation may be
needed to remove electricity.
Electrically ground all conveyors, solder vessels, soldering irons and peripheral equipment.
Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of 1
MΩ).
Wearing of conductive clothing and shoes, use of conductive floor mats and other measures to minimize shock loads is
recommended.
Ground all fixtures and instruments, or protect with anti-static measures.
Avoid the use of styrofoam or other highly static-prone materials for storage of completed board assemblies.
Document Number: 002-05631 Rev *B
Page 50 of 128
MB9AB40NB Series
6.3
Precautions for Use Environment
Reliability of semiconductor devices depends on ambient temperature and other conditions as described above.
For reliable performance, do the following:
1.
Humidity
Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are
anticipated, consider anti-humidity processing.
2.
Discharge of Static Electricity
When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases, use
anti-static measures or processing to prevent discharges.
3.
Corrosive Gases, Dust, or Oil
Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If you
use devices in such conditions, consider ways to prevent such exposure or to protect the devices.
4.
Radiation, Including Cosmic Radiation
Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide shielding
as appropriate.
5.
Smoke, Flame
CAUTION: Plastic molded devices are flammable, and therefore should not be used near combustible substances. If devices begin
to smoke or burn, there is danger of the release of toxic gases.
Customers considering the use of Cypress products in other special environmental conditions should consult with sales
representatives.
Document Number: 002-05631 Rev *B
Page 51 of 128
MB9AB40NB Series
7.
Handling Devices
Power supply pins
In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to
prevent malfunctions such as latch-up. However, all of these pins should be connected externally to the power supply or ground
lines in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the
ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with each Power supply pin and GND pin of this device at low impedance. It is also
advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between each Power supply pin
and GND pin, between AVCC pin and AVSS pin near this device.
Stabilizing supply voltage
A malfunction may occur when the power supply voltage fluctuates rapidly even though the fluctuation is within the recommended
operating conditions of the VCC power supply voltage. As a rule, with voltage stabilization, suppress the voltage fluctuation so
that the fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the
VCC value in the recommended operating conditions, and the transient fluctuation rate does not exceed 0.1 V/μs when there is a
momentary fluctuation on switching the power supply.
Crystal oscillator circuit
Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1,
X0A/X1A pins, the crystal oscillator, and the bypass capacitor to ground are located as close to the device as possible.
It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by
ground plane as this is expected to produce stable operation.
Evaluate oscillation of your using crystal oscillator by your mount board.
Sub crystal oscillator
This series sub oscillator circuit is low gain to keep the low current consumption.
The crystal oscillator to fill the following conditions is recommended for sub crystal oscillator to stabilize the oscillation.
Surface mount type
Size:
More than 3.2 mm × 1.5 mm
Load capacitance: Approximately 6 pF to 7 pF Lead type
Load capacitance: Approximately 6 pF to 7 pF
Using an external clock
When using an external clock as an input of the main clock, set X0/X1 to the external clock input, and input the clock to X0.
X1(PE3) can be used as a general-purpose I/O port.
Similarly, when using an external clock as an input of the sub clock, set X0A/X1A to the external clock input, and input the clock
to X0A. X1A (P47) can be used as a general-purpose I/O port.
Example of Using an External Clock
Device
X0(X0A)
Can be used as
general-purpose
I/O ports.
Document Number: 002-05631 Rev *B
X1(PE3),
X1A (P47)
Set as
External clock
input
Page 52 of 128
MB9AB40NB Series
Handling when using Multi-function serial pin as I2C pin
If it is using the multi-function serial pin as I2C pins, P-ch transistor of digital output is always disabled. However, I2C pins need to
keep the electrical characteristic like other pins and not to connect to the external I2C bus system with power OFF.
C Pin
This series contains the regulator. Be sure to connect a smoothing capacitor (C S) for the regulator between the C pin and the GND
pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor.
However, some laminated ceramic capacitors have the characteristics of capacitance variation due to thermal fluctuation (F
characteristics and Y5V characteristics). Please select the capacitor that meets the specifications in the operating conditions to
use by evaluating the temperature characteristics of a capacitor.
A smoothing capacitor of about 4.7μF would be recommended for this series.
C
Device
CS
VSS
GND
Mode pins (MD0)
Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistance
stays low, as well as the distance between the mode pins and VCC pins or VSS pins is as short as possible and the connection
impedance is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
Notes on power-on
Turn power on/off in the following order or at the same time.
If not using the A/D converter, connect AVCC = VCC and AVSS = VSS.
Turning on : VCC →AVCC → AVRH
Turning off : AVRH → AVCC → VCC
Serial Communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider the case of receiving wrong data due to noise, perform error detection such as by applying a checksum of data at the
end. If an error is detected, retransmit the data.
Differences in features among the products with different memory sizes and between Flash memory products
and MASK products
The electric characteristics including power consumption, ESD, latch-up, noise characteristics, and oscillation characteristics
among the products with different memory sizes and between Flash memory products and MASK products are different because
chip layout and memory structures are different.
If you are switching to use a different product of the same series, please make sure to evaluate the electric characteristics.
Pull-Up function of 5 V tolerant I/O
Please do not input the signal more than VCC voltage at the time of Pull-Up function use of 5 V tolerant I/O.
Document Number: 002-05631 Rev *B
Page 53 of 128
MB9AB40NB Series
8.
Block Diagram
TRSTX,TCK,
TDI,TMS
TDO
TRACEDx,
TRACECLK
ETM*1
SWJ-DP
TPIU*
SRAM0
8/16 Kbyte
ROM
Table
1
Multi-layer AHB (Max 40 MHz)
Cortex-M3 Core I
@40 MHz(Max)
D
NVIC
Sys
AHB-APB Bridge:
APB0(Max 40 MHz)
Dual-Timer
WatchDog Timer
(Software)
Clock Reset
Generator
INITX
WatchDog Timer
(Hardware)
SRAM1
8/16 Kbyte
On-Chip Flash
64+32 Kbyte/
128+32 Kbyte/
256+32 Kbyte
Flash I/F
Security
USB2.0
PHY
(Host/
Device)
UDP0/UDM0
UHCONX
DMAC
8ch.
CSV
Main
Osc
Sub
Osc
PLL
CR
4 MHz
AHB-AHB
Bridge
CLK
X0
X1
X0A
X1A
CROUT
Source Clock
CR
100 kHz
MADx
External Bus I/F*2
ADTGx
TIOAx
TIOBx
VVx
COMx,
SEGx
CEC0,CEC1
RTCCO,
SUBOUT
WKUPx
Unit 0
Unit 1
Base Timer
16-bit 8ch./
32-bit 4ch.
USB Clock Ctrl
PLL
Power-On
Reset
LVD Ctrl
MCSXx,
MOEX,
MWEX,
MALE,
MRDY,
MCLKOUT,
MDQMx
LVD
Regulator
C
IRQ-Monitor
AHB-APB Bridge : APB2 (Max 40 MHz)
ANxx
MADATAx
12-bit A/D Converter
AHB-APB Bridge : APB1 (Max 40 MHz)
AVCC,
AVSS,
AVRH
CRC
Accelerator
Watch Counter
External Interrupt
Controller
16-pin + NMI
INTx
NMIX
MODE-Ctrl
MD0,
MD1
P0x,
P1x,
LCDC
GPIO
PIN-Function-Ctrl
HDMI-CEC/
Remote Reciver Control
Real-Time Clock
.
.
.
PEx
Multi-Function Serial I/F
8ch.
(with FIFO ch.4 to ch.7)
HW flow control(ch.4)*2
Deep Standby Ctrl
SCKx
SINx
SOTx
CTS4
RTS4
*1: For the MB9AFB41LB/MB, MB9AFB42LB/MB, and MB9AFB44LB/MB, ETM is not available.
*2: For the MB9AFB41LB, MB9AFB42LB and MB9AFB44LB, the External Bus Interface is not available. And the Multi-function
Serial Interface does not support hardware flow control in these products.
9.
Memory Size
See Memory size in Product Lineup to confirm the memory size.
Document Number: 002-05631 Rev *B
Page 54 of 128
MB9AB40NB Series
10.
Memory Map
Memory Map (1)
Peripherals Area
0x41FF_FFFF
Reserved
0xFFFF_FFFF
Reserved
0xE010_0000
0xE000_0000
Cortex-M3 Private
Peripherals
0x4006_1000
0x4006_0000
0x4005_0000
0x4004_0000
0x4003_F000
Reserved
0x4003_C000
0x4003_B000
0x4003_A000
0x7000_0000
0x6000_0000
External Device
Area
Reserved
0x4003_9000
0x4003_8000
0x4003_7000
0x4003_6000
0x4003_5000
0x4400_0000
0x4200_0000
0x4000_0000
32Mbytes
Bit band alias
Peripherals
Reserved
0x2400_0000
0x2200_0000
0x1FFF_0000
0x0020_8000
0x0020_0000
See the next page
"lMemory Map (2)"
for the memory size
details.
0x0010_4000
0x0010_0000
0x4003_3000
0x4003_2000
0x4003_1000
0x4003_0000
0x4002_F000
0x4002_E000
32Mbytes
Bit band alias
Reserved
0x2008_0000
0x2000_0000
0x4003_4000
0x4002_8000
Reserved
0x4002_7000
A/DC
0x4002_6000
Reserved
0x4002_5000
Base Timer
SRAM1
SRAM0
Reserved
Flash(Work area)
Reserved
Security/CR Trim
Reserved
0x4001_6000
0x4001_5000
Flash(Main area)
0x0000_0000
0x4001_3000
0x4001_2000
0x4001_1000
0x4001_0000
0x4000_1000
0x4000_0000
Document Number: 002-05631 Rev *B
DMAC
Reserved
USB ch.0
EXT-bus I/F
Reserved
RTC
Watch Counter
CRC
MFS
Reserved
USB Clock Ctrl
LVD/DS mode
HDMI-CEC/
Remote Control Receiver
GPIO
LCDC
Int-Req.Read
EXTI
Reserved
CR Trim
Dual Timer
Reserved
SW WDT
HW WDT
Clock/Reset
Reserved
Flash I/F
Page 55 of 128
MB9AB40NB Series
Memory Map (2)
MB9AFB44LB/MB/NB
MB9AFB42LB/MB/NB
0x2008_0000
MB9AFB41LB/MB/NB
0x2008_0000
Reserved
0x2008_0000
Reserved
Reserved
0x2000_4000
0x2000_2000
SRAM1
16Kbytes
0x2000_0000
0x2000_0000
SRAM0
16Kbytes
0x1FFF_E000
0x2000_2000
SRAM1
8Kbytes
SRAM0
8Kbytes
0x2000_0000
0x1FFF_E000
SRAM1
8Kbytes
SRAM0
8Kbytes
0x1FFF_C000
SA4-7 (8 KBx4)
Reserved
0x0010_4000
0x0010_2000
0x0010_0000
0x0020_0000
SA4-7 (8 KBx4)
Reserved
0x0010_4000
CR trimming
Security
0x0010_2000
0x0010_0000
0x0020_8000
0x0020_0000
SA4-7 (8 KBx4)
Reserved
Flash(Work area)
32 Kbytes
0x0020_0000
0x0020_8000
Reserved
Flash(Work area)
32 Kbytes
0x0020_8000
Reserved
Flash(Work area)
32 Kbytes
Reserved
0x0010_4000
CR trimming
Security
0x0010_2000
0x0010_0000
CR trimming
Security
Reserved
Reserved
Reserved
0x0000_0000
SA2-3 (8 KBx2)
SA9 (64 KB)
SA8 (48 KB)
0x0000_0000
SA2-3 (8 KBx2)
0x0001_0000
SA8 (48 KB)
0x0000_0000
Flash(Main area)
64 Kbytes
SA8 (48 KB)
0x0002_0000
Flash(Main area)
128 Kbytes
SA9-11 (64 KBx3)
Flash(Main area)
256 Kbytes
0x0004_0000
SA2-3 (8 KBx2)
Refer to the programming manual for the detail of Flash main area.
MB9AB40N/A40N/340N/140N/150R,MB9B520M/320M/120M Series Flash Programming Manual
Document Number: 002-05631 Rev *B
Page 56 of 128
MB9AB40NB Series
Peripheral Address Map
Start address
End address
Bus
Peripherals
0x4000_0000
0x4000_0FFF
0x4000_1000
0x4000_FFFF
0x4001_0000
0x4001_0FFF
Clock/Reset Control
0x4001_1000
0x4001_1FFF
Hardware Watchdog timer
0x4001_2000
0x4001_2FFF
0x4001_3000
0x4001_4FFF
0x4001_5000
0x4001_5FFF
Dual Timer
0x4001_6000
0x4001_FFFF
Reserved
0x4002_0000
0x4002_4FFF
Reserved
0x4002_5000
0x4002_5FFF
Base Timer
0x4002_6000
0x4002_6FFF
0x4002_7000
0x4002_7FFF
0x4002_8000
0x4002_DFFF
Reserved
0x4002_E000
0x4002_EFFF
Built-in CR trimming
0x4002_F000
0x4002_FFFF
Reserved
0x4003_0000
0x4003_0FFF
External Interrupt
0x4003_1000
0x4003_1FFF
Interrupt source check register
0x4003_2000
0x4003_2FFF
LCDC
0x4003_3000
0x4003_3FFF
GPIO
0x4003_4000
0x4003_4FFF
HDMI-CEC/Remote control Receiver
0x4003_5000
0x4003_57FF
Low-Voltage Detector
0x4003_5800
0x4003_5FFF
0x4003_6000
0x4003_6FFF
0x4003_7000
0x4003_7FFF
Reserved
0x4003_8000
0x4003_8FFF
Multi-function serial
0x4003_9000
0x4003_9FFF
CRC
0x4003_A000
0x4003_AFFF
Watch Counter
0x4003_B000
0x4003_BFFF
Real-time clock
0x4003_C000
0x4003_EFFF
Reserved
0x4003_F000
0x4003_FFFF
External Memory interface
0x4004_0000
0x4004_FFFF
USB ch.0
0x4005_0000
0x4005_FFFF
0x4006_0000
0x4006_0FFF
0x4006_1000
0x41FF_FFFF
Document Number: 002-05631 Rev *B
AHB
APB0
Flash memory I/F register
Reserved
Software Watchdog timer
Reserved
Reserved
APB1
A/D Converter
Deep standby mode Controller
APB2
AHB
USB clock generator
Reserved
DMAC register
Reserved
Page 57 of 128
MB9AB40NB Series
11.
Pin Status in Each CPU State
The terms used for pin status have the following meanings.
 INITX=0
This is the period when the INITX pin is the L level.
 INITX=1
This is the period when the INITX pin is the H level.
 SPL=0
This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 0.
 SPL=1
This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 1.
 Input enabled
Indicates that the input function can be used.
 Internal input fixed at 0
This is the status that the input function cannot be used. Internal input is fixed at L.
 Hi-Z
Indicates that the pin drive transistor is disabled and the pin is put in the Hi-Z state.
 Setting disabled
Indicates that the setting is disabled.
 Maintain previous state
Maintains the state that was immediately prior to entering the current mode.
If a built-in peripheral function is operating, the output follows the peripheral function.
If the pin is being used as a port, that output is maintained.
 Analog input is enabled
Indicates that the analog input is enabled.
 Trace output
Indicates that the trace function can be used.
 GPIO selected
In Deep standby mode, pins switch to the general-purpose I/O port.
Document Number: 002-05631 Rev *B
Page 58 of 128
MB9AB40NB Series
Pin status type
List of Pin Status
A
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
INITX
input
state
Device
internal
reset
state
Power supply stable
Run
mode or
Sleep
mode
state
Power
supply
stable
-
INITX = 0
INITX = 1
INITX = 1
-
-
-
-
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Return
from
Deep
standby
mode
state
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
SPL = 0
SPL = 1
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Main crystal
oscillator
input pin/
External
main clock
input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
External
main clock
input
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
SPL = 0
GPIO
selected
Internal
input fixed
at 0
SPL = 1
-
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Input
enabled
Input
enabled
Input
enabled
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state/
When
oscillation
stops[1],,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops[1],,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops[1],,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops[1],,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops[1],,
Hi-Z /
Internal
input fixed
at 0
B
Main crystal
oscillator
output pin
Hi-Z /
Internal
input fixed at
0/
or Input
enabled
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops[1],
Hi-Z /
Internal
input fixed
at 0
C
INITX
input pin
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
D
Mode
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Document Number: 002-05631 Rev *B
Page 59 of 128
Pin status type
MB9AB40NB Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
INITX
input
state
Device
internal
reset
state
Power supply stable
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Return
from
Deep
standby
mode
state
Power
supply
stable
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
Run
mode or
Sleep
mode
state
-
INITX = 0
INITX = 1
INITX = 1
-
-
-
-
SPL = 0
SPL = 1
SPL = 0
SPL = 1
-
Mode
input pin
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Input
enabled
GPIO
selected
Hi-Z /
Input
enabled
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
E
F
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Sub crystal
oscillator
input pin /
External sub
clock input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
External sub
clock input
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z/
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state/Whe
n
oscillation
stops[2],
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/Whe
n
oscillation
stops[2],
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/Whe
n
oscillation
stops[2],
Hi-Z/
Internal
input fixed
at 0
Maintain
previous
state/Whe
n
oscillation
stops[2],
Hi-Z/
Internal
input fixed
at 0
Maintain
previous
state/Whe
n
oscillation
stops[2],
Hi-Z/
Internal
input fixed
at 0
G
Sub crystal
oscillator
output pin
Hi-Z /
Internal
input fixed at
0/
or Input
enable
Document Number: 002-05631 Rev *B
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Page 60 of 128
Pin status type
MB9AB40NB Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
GPIO
selected
INITX
input
state
Device
internal
reset
state
Power supply stable
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Return
from
Deep
standby
mode
state
Power
supply
stable
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
Run
mode or
Sleep
mode
state
-
INITX = 0
INITX = 1
INITX = 1
-
-
-
-
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
I
Setting
disabled
Setting
disabled
Setting
disabled
NMIX
selected
Setting
disabled
Setting
disabled
Setting
disabled
Resource
other than
above
selected
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Hi-Z
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
GPIO
selected
JTAG
selected
J
GPIO
selected
Resource
selected
K
GPIO
selected
Document Number: 002-05631 Rev *B
SPL = 1
SPL = 0
SPL = 1
-
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Maintain
previous
state
Hi-Z at
transmission/
Input
enabled/
Internal
input fixed
at 0 at
reception
Hi-Z at
transmission/
Input
enabled/
Internal
input fixed
at 0 at
reception
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
WKUP
input
enabled
Hi-Z /
WKUP
input
enabled
GPIO
selected
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
H
USB I/O pin
SPL = 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Page 61 of 128
Pin status type
MB9AB40NB Series
Function
group
Power
supply
unstable
External
interrupt
enabled
selected
L
Power-on
reset or
low-voltage
detection
state
Resource
other than
above
selected
Power supply stable
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Return
from
Deep
standby
mode
state
Power
supply
stable
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
Run
mode or
Sleep
mode
state
-
INITX = 0
INITX = 1
INITX = 1
-
-
-
-
Setting
disabled
Setting
disabled
SPL = 0
SPL = 1
Maintain
previous
state
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
SPL = 0
SPL = 1
-
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
GPIO
selected
Analog input
selected
INITX
input
state
Device
internal
reset
state
M
Resource
other than
above
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Analog input
selected
N
External
interrupt
enabled
selected
Resource
other than
above
selected
Maintain
previous
state
Setting
disabled
GPIO
selected
Document Number: 002-05631 Rev *B
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Page 62 of 128
Pin status type
MB9AB40NB Series
Function
group
Power
supply
unstable
Trace
selected
O
Power-on
reset or
low-voltage
detection
state
Resource
other than
above
selected
P
Power supply stable
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Return
from
Deep
standby
mode
state
Power
supply
stable
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
Run
mode or
Sleep
mode
state
-
INITX = 0
INITX = 1
INITX = 1
-
-
-
-
Setting
disabled
Setting
disabled
SPL = 0
Setting
disabled
Hi-Z
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Analog input
selected
INITX
input
state
Device
internal
reset
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Q
Trace
selected
External
interrupt
enabled
selected
Resource
other than
above
selected
SPL = 1
-
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Trace
output
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Analog input
selected
SPL = 0
Trace
output
Trace
selected
Resource
other than
above
selected
SPL = 1
Setting
disabled
GPIO
selected
Document Number: 002-05631 Rev *B
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Trace
output
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Page 63 of 128
Pin status type
MB9AB40NB Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
Analog input
selected
INITX
input
state
Device
internal
reset
state
Power supply stable
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Return
from
Deep
standby
mode
state
Power
supply
stable
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
Run
mode or
Sleep
mode
state
-
INITX = 0
INITX = 1
INITX = 1
-
-
-
-
SPL = 0
SPL = 1
SPL = 0
SPL = 1
-
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
WKUP
input
enabled
Hi-Z /
WKUP
input
enabled
Hi-Z
WKUP
enabled
Maintain
previous
state
R
External
interrupt
enabled
selected
Resource
other than
above
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Resource
other than
above
selected
GPIO
selected
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
CEC
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
WKUP
enabled
T
Hi-Z /
Internal
input fixed
at 0
Setting
disabled
CEC
enabled
S
GPIO
selected
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
External
interrupt
enabled
selected
Resource
other than
above
selected
Setting
disabled
Setting
disabled
Maintain
previous
state
Setting
disabled
Maintain
previous
state
Hi-Z
GPIO
selected
Document Number: 002-05631 Rev *B
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
WKUP
input
enabled
GPIO
selected
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z /
WKUP
input
enabled
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
GPIO
selected
Page 64 of 128
Pin status type
MB9AB40NB Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
GPIO
selected
External
interrupt
enabled
selected
V
Resource
other than
above
selected
W
Resource
other than
above
selected
X
Y
GPIO
selected
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Power
supply
stable
Power supply stable
Power supply stable
Power
supply
stable
INITX = 1
INITX = 1
INITX = 1
INITX = 1
INITX = 1
-
-
-
-
Hi-Z
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
SPL = 0
Maintain
previous
state
SPL = 1
SPL = 0
SPL = 1
-
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Setting
disabled
Setting
disabled
Setting
disabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
resource
selected
Return
from
Deep
standby
mode
state
INITX = 0
GPIO
selected
Analog input
selected
Power supply stable
Timer mode,
RTC mode, or
Sleep mode state
Deep standby
RTC mode or Deep
standby Stop mode
state
Run
mode or
Sleep
mode
state
resource
selected
U
INITX
input
state
Device
internal
reset
state
Hi-Z
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
1: Oscillation is stopped at Sub Timer mode, Low-speed CR Timer mode, RTC mode, Stop mode, Deep Standby RTC mode, and
Deep Standby Stop mode.
2: Oscillation is stopped at Stop mode and Deep Standby Stop mode.
Document Number: 002-05631 Rev *B
Page 65 of 128
MB9AB40NB Series
12.
Electrical Characteristics
12.1
Absolute Maximum Ratings
Parameter
[1],[2]
Power supply voltage
Analog power supply voltage[1],[3]
Analog reference voltage[1],[3]
LCD input voltage [1],[3]
Input voltage[1]
Symbol
VCC
AVCC
AVRH
VV0 to
VV4
VI
Rating
Max
VSS + 4.6
VSS + 4.6
VSS + 4.6
V
V
V
VSS - 0.5
VSS + 4.6
V
VSS - 0.5
VSS - 0.5
Analog pin input voltage
[1]
Unit
Min
VSS - 0.5
VSS - 0.5
VSS - 0.5
VIA
VSS - 0.5
Output voltage[1]
VO
VSS - 0.5
L level maximum output current[4]
IOL
-
L level average output current[5]
IOLAV
-
L level total maximum output current
L level total average output current[6]
∑IOL
∑IOLAV
-
H level maximum output current[4]
IOH
-
H level average output current[5]
IOHAV
-
H level total maximum output current
H level total average output current[6]
Power consumption
Storage temperature
∑IOH
∑IOHAV
PD
TSTG
- 55
VCC + 0.5
(≤ 4.6 V)
VSS + 6.5
AVCC + 0.5
(≤ 4.6 V)
VCC + 0.5
(≤ 4.6 V)
10
Remarks
V
V
5 V tolerant
V
V
mA
39
mA
4
10.5
27
100
50
- 10
mA
mA
mA
mA
mA
mA
39
mA
-4
12
27
- 100
- 50
300
+ 150
mA
mA
mA
mA
mA
mW
°C
P81/UDP0 ,
P80/UDM0 pins
[7]
[8]
P81/UDP0 ,
P80/UDM0 pins
[7]
[8]
1: These parameters are based on the condition that VSS = AVSS = 0V.
2: VCC must not drop below VSS - 0.5V.
3: Ensure that the voltage does not to exceed VCC + 0.5 V, for example, when the power is turned on.
4: The maximum output current is defined as the value of the peak current flowing through any one of the corresponding pins.
5: The average output current is defined as the average current value flowing through any one of the corresponding pins for a 100
ms period.
6: The total average output current is defined as the average current value flowing through all of corresponding pins for a 100ms.
7: When P81/UDP0 and P80/UDM0 pins are used as GPIO (P81, P80).
8: Then P81/UDP0 and P80/UDM0 pins are used as USB (UDP0, UDM0).
WARNING:
−
Semiconductor devices may be permanently damaged by application of stress (including, without limitation, voltage, current
or temperature) in excess of absolute maximum ratings.Do not exceed any of these ratings.
Document Number: 002-05631 Rev *B
Page 66 of 128
MB9AB40NB Series
12.2
Recommended Operating Conditions
(VSS = AVSS = 0.0V)
Parameter
Power supply voltage
LCD input voltage
Analog power supply voltage
Symbol
VCC
VVV4
AVCC
Conditions
-
AVRH
-
Analog reference voltage
AVRL
Smoothing capacitor
Operating temperature
CS
TA
-
Value
Unit
Min
1.65[6]
3.0[6]
Max
3.6
3.6
V
2.2[6]
2.2
1.65
2.7
AVCC
3.6
VCC
3.6
AVCC
AVCC
V
V
V
V
AVSS
1
- 40
AVSS
10
+ 85
V
µF
°C
Remarks
[1], [4]
[2]
[1], [3]
AVCC = VCC
AVCC ≥ 2.7 V
AVCC< 2.7 V
For Regulator[5]
1: When P81/UDP0 and P80/UDM0 pins are used as GPIO (P81, P80).
2: When P81/UDP0 and P80/UDM0 pins are used as USB (UDP0, UDM0).
3: When LCD Controller is used.
4: When LCD Controller is not used.
5: See C Pin in Handling Devices for the connection of the smoothing capacitor.
6: In between less than the minimum power supply voltage and low voltage reset/interrupt detection voltage
or more, instruction execution and low voltage detection function by built-in High-speed CR(including Main PLL is used) or built-in
Low-speed CR is possible to operate only.
WARNING:
−
The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All
of the device's electrical characteristics are warranted when the device is operated under these conditions. Any use of
semiconductor devices will be under their recommended operating condition.
Operation under any conditions other than these conditions may adversely affect reliability of device and could result in
device failure. No warranty is made with respect to any use, operating conditions or combinations not represented on this
data sheet. If you are considering application under any conditions other than listed herein, please contact sales
representatives beforehand.
Document Number: 002-05631 Rev *B
Page 67 of 128
MB9AB40NB Series
12.3
DC Characteristics
12.3.1
Current rating
(VCC = AVCC = 1.65V to 3.6V, VSS = AVSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin
name
ICC
Power
supply
current
VCC
ICCS
Conditions
Value
Unit
Remarks
Typ[3]
Max[4]
15.5
21
mA
[1], [5]
8.7
12
mA
[1], [5]
PLL
Rrun mode
CPU: 40 MHz,
Peripheral: 40 MHz
CPU: 40 MHz,
Peripheral: the clock stops
NOP operation
High-speed CR
Rrun mode
CPU/ Peripheral: 4 MHz[2]
1.8
2.9
mA
[1]
CPU/ Peripheral: 32 kHz
110
680
μA
[1], [6]
CPU/ Peripheral: 100 kHz
125
700
μA
[1]
Peripheral: 40 MHz
9
12.5
mA
[1], [5]
Peripheral: 4 MHz[2]
0.8
1.6
mA
[1]
Peripheral: 32 kHz
96
670
μA
[1], [6]
Peripheral: 100 kHz
110
680
μA
[1]
Sub
Rrun mode
Low-speed CR
Run mode
PLL
Sleep mode
High-speed CR
Sleep mode
Sub
Sleep mode
Low-speed CR
Sleep mode
1: When all ports are fixed.
2: When setting it to 4 MHz by trimming.
3: TA=+25°C, VCC=3.6 V
4: TA=+85°C, VCC=3.6 V
5: When using the crystal oscillator of 4 MHz (Including the current consumption of the oscillation circuit)
6: When using the crystal oscillator of 32 kHz (Including the current consumption of the oscillation circuit)
Document Number: 002-05631 Rev *B
Page 68 of 128
MB9AB40NB Series
Parameter
Symbol
Pin
name
Conditions
Main Timer
mode
ICCT
Sub Timer
mode
ICCR
RTC mode
ICCH
Power supply
current
Stop mode
VCC
ICCHD
ICCRD
Deep Standby
Stop mode
Deep Standby
RTC mode
Value
Unit
Remarks
Typ[2]
Max[2]
2.1
2.5
mA
[1], [3]
-
3.4
mA
[1], [3]
12
35
μA
[1], [4]
-
330
μA
[1], [4]
9.8
29
μA
[1], [4]
-
280
μA
[1], [4]
9
28
μA
[1]
TA = + 85°C,
When LVD is off
-
270
μA
[1]
TA = + 25°C,
When LVD is off,
When RAM is off
1.25
7
μA
[1], [4], [5]
TA = + 25°C,
When LVD is off,
When RAM is on
5.3
18
μA
[1], [4], [5]
70
μA
[1], [4], [5]
100
μA
[1], [4], [5]
1.9
9
μA
[1], [5]
TA = + 25°C,
When LVD is off,
When RAM is on
5.9
20
μA
[1], [5]
TA = + 85°C,
When LVD is off,
When RAM is off
TA = + 85°C,
When LVD is off,
When RAM is on
75
μA
[1], [5]
105
μA
[1], [5]
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off,
When RAM is off
TA = + 85°C,
When LVD is off,
When RAM is on
TA = + 25°C,
When LVD is off,
When RAM is off
-
1: When all ports are fixed.
2: VCC=3.6 V
3: When using the crystal oscillator of 4 MHz (Including the current consumption of the oscillation circuit)
4: When using the crystal oscillator of 32 kHz (Including the current consumption of the oscillation circuit)
5: RAM on/off setting is on-chip SRAM only.
Document Number: 002-05631 Rev *B
Page 69 of 128
MB9AB40NB Series
Low-Voltage Detection Current
(VCC = 1.65V to 3.6V, VDDI = 1.1V to 1.3V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Low-voltage
detection circuit
(LVD) power
supply current
Pin
name
Symbol
ICCLVD
Conditions
Value
Typ
Max
Unit
Remarks
At operation
for reset
VCC = 3.6 V
0.13
0.3
μA
At not detect
At operation
for interrupt
VCC = 3.6 V
0.13
0.3
μA
At not detect
VCC
Flash Memory Current
(VCC = 1.65V to 3.6V, VDDI = 1.1V to 1.3V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Flash memory
write/erase
current
Pin
name
Symbol
ICCFLASH
VCC
Conditions
At Write/Erase
Value
Typ
9.5
Max
11.2
Unit
mA
Remarks
*
*: The current at which to write or erase Flash memory, ICCFLASH is added to ICC.
A/D Converter Current
(VCC = VCC28 = AVCC = 1.65V to 3.6V, VDDI = 1.1V to 1.3V, VSS = AVSS = 0V, TA = - 40°C to +85°C)
Parameter
Power supply
current
Reference power
supply current
Pin
name
Symbol
ICCAD
ICCAVRH
Conditions
Value
Typ
Max
Unit
At 1unit
operation
0.27
0.42
mA
At stop
0.03
10
μA
At 1unit
operation
AVRH=3.6 V
0.72
1.29
mA
At stop
0.02
2.6
μA
Remarks
AVCC
AVRH
Document Number: 002-05631 Rev *B
Page 70 of 128
MB9AB40NB Series
12.3.2
Pin Characteristics
(VCC = AVCC = 1.65V to 3.6V, VSS = AVSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin name
Value
Conditions
Min
H level input
voltage
(hysteresis
input)
L level input
voltage
(hysteresis
input)
CMOS
hysteresis input pin,
MD0, MD1
VIHS
VCC ≥ 2.7 V
VCC × 0.8
VCC < 2.7 V
VCC × 0.7
VCC ≥ 2.7 V
VCC × 0.8
VCC < 2.7 V
VCC × 0.7
5V tolerant input pin
CMOS
hysteresis input pin,
MD0, MD1
Typ
Max
-
VCC + 0.3
V
-
VSS + 5.5
V
VCC ≥ 2.7 V
Remark
s
VCC × 0.2
VSS - 0.3
-
V
VCC < 2.7 V
VCC × 0.3
VCC ≥ 2.7 V
VCC × 0.2
VILS
5V tolerant input pin
VSS - 0.3
-
VCC < 2.7 V
4mA type
H level
output
voltage
Unit
VOH
The pin doubled as
USB I/O
V
VCC × 0.3
VCC ≥ 2.7 V,
IOH = - 4 mA
VCC - 0.5
VCC < 2.7 V,
IOH = - 2 mA
VCC - 0.45
-
VCC
V
VCC - 0.4
-
VCC
V
VSS
-
0.4
V
VSS
-
0.4
V
VCC = AVCC =
AVRH = VSS =
AVSS = 0.0 V
-5
-
+5
μA
-
-
+1.8
μA
VCC ≥ 2.7 V
21
33
66
VCC < 2.7 V
-
-
134
-
-
5
15
VCC ≥ 2.7 V,
IOH = - 12 mA
VCC < 2.7 V,
IOH = - 6.5 mA
VCC ≥ 2.7 V,
IOL = 4 mA
4mA type
L level
output
voltage
VCC < 2.7 V,
IOL = 2 mA
VOL
The pin doubled as
USB I/O
Input leak
current
Pull-up
resistor
value
Input
capacitance
IIL
RPU
CIN
CEC0,
CEC1
VCC ≥ 2.7 V,
IOL = 10.5 mA
VCC < 2.7 V,
IOL = 5 mA
Pull-up pin
Other than VCC,
VSS,
AVCC,
AVSS, AVRH
Document Number: 002-05631 Rev *B
kΩ
pF
Page 71 of 128
MB9AB40NB Series
12.4
LCD Characteristics
(VCC = 2.2V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin
name
VVV0
VV0
VVV1
VVV2
VVV3
VV1
VV2
VV3
VVV0
VV0
VVV1
VVV2
VVV3
VV1
VV2
VV3
VVV0
VV0
VVV1
VVV2
VVV3
VV1
VV2
VV3
IR100K
VV4
IR10K
VV4
IR100K
VV4
IR10K
VV4
IR100K
VV4
IR10K
VV4
VV4
Static current
IOFF_VV4
VV4
VV0
Output Voltage
in using
external resistor
VVV0E
VV0
VV0 to VV3
Output voltage
(1/4 bias)
VV0 to VV3
Output voltage
(1/3 bias)
VV0 to VV3
Output voltage
(1/2 bias)
VV4
Active current
(1/4 bias)
VV4
Active current
(1/3 bias)
VV4
Active current
(1/2 bias)
Document Number: 002-05631 Rev *B
Value
Conditions
Min
Unit
Typ
0
-
VVV4 × 5%
VVV4 × 1/4-10%
VVV4 × 1/2-10%
VVV4 × 3/4-10%
-
VVV4 × 1/4+10%
VVV4 × 1/2+10%
VVV4 × 3/4+10%
0
-
VVV4 × 5%
VVV4 × 1/3-10%
VVV4 × 2/3 -10%
VVV4 × 2/3-10%
-
VVV4 × 1/3+10%
VVV4 × 2/3+10%
VVV4 × 2/3+10%
0
-
VVV4 × 5%
VVV4 × 1/2-10%
VVV4 × 1/2-10%
VVV4 × 1/2-10%
-
VVV4 × 1/2+10%
VVV4 × 1/2+10%
VVV4 × 1/2+10%
V
-
10
20
μA
-
100
160
μA
-
12
30
μA
-
120
180
μA
-
18
40
μA
-
180
270
μA
When LCD
stops
-
0.5
1.5
μA
IOL=1 mA
-
-
0.66
V
When using
internal dividing
resistor
When using
internal dividing
resistor
When using
internal dividing
resistor
When using
100 kΩ internal
dividing resistor
When using
10 kΩ internal
dividing resistor
When using
100 kΩ internal
dividing resistor
When using
10 kΩ internal
dividing resistor
When using
100 kΩ internal
dividing resistor
When using
10 kΩ internal
dividing resistor
Remarks
Max
V
V
Page 72 of 128
MB9AB40NB Series
12.5
AC Characteristics
12.5.1
Main Clock Input Characteristics
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Input frequency
Input clock cycle
Input clock pulse
width
Input clock rising time
and falling time
Internal operating
Clock[1] frequency
Internal operating
clock[1] cycle time
Symbo
l
Pin
name
fCH
tCYLH
X0,
X1
Value
Conditions
Min
VCC ≥ 2.7 V
VCC < 2.7 V
4
4
Max
48
20
-
4
-
Unit
Remarks
MHz
When crystal oscillator is
connected
48
MHz
When using external
clock
20.83
250
ns
When using external
clock
PWH/tCYLH,
PWL/tCYLH
45
55
%
-
-
5
ns
tCF,
tCR
fCM
-
-
-
40
MHz
When using external
clock
When using external
clock
Master clock
fCC
-
-
-
40
MHz
Base clock (HCLK/FCLK)
fCP0
fCP1
-
-
-
40
40
MHz
MHz
APB0 bus clock[2]
APB1 bus clock[2]
fCP2
-
-
-
40
MHz
APB2 bus clock[2]
tCYCC
tCYCP0
tCYCP1
tCYCP2
-
-
25
-
ns
Base clock (HCLK/FCLK)
-
-
25
-
ns
APB0 bus clock[2]
-
-
25
-
ns
APB1 bus clock[2]
-
-
25
-
ns
APB2 bus clock[2]
-
1: For more information about each internal operating clock, see Chapter 2-1: Clock in FM3 Family Peripheral Manual.
2: For about each APB bus which each peripheral is connected to, see Block Diagram in this datasheet.
X0
Document Number: 002-05631 Rev *B
Page 73 of 128
MB9AB40NB Series
12.5.2
Sub Clock Input Characteristics
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Input frequency
Pin
name
Symbol
Value
Conditions
Min
Typ
Unit
Max
-
-
32.768
-
kHz
-
32
-
100
kHz
-
10
-
31.25
μs
PWH/tCYLL,
PWL/tCYLL
45
-
55
%
When crystal oscillator
is connected
When using external
clock
When using external
clock
When using external
clock
fCL
Input clock cycle
tCYLL
Input clock pulse
width
-
X0A,
X1A
Remarks
X0A
12.5.3
Built-in CR Oscillation Characteristics
Built-in High-speed CR
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Clock frequency
Frequency
stabilization time
Symbol
fCRH
tCRWT
Value
Conditions
Min
Typ
Max
TA = + 25°C
VCC ≥ 2.7 V
3.96
4
4.04
TA = + 25°C
VCC < 2.7 V
3.9
4
4.1
TA = - 40°C to + 85°C
3.84
4
4.16
TA = - 40°C to + 85°C
2.8
-
5.2
-
-
-
30
Unit
MHz
Remarks
When trimming[1]
When not trimming
μs
[2]
1: In the case of using the values in CR trimming area of Flash memory at shipment for frequency/temperature trimming.
2: This is the time to stabilize the frequency of High-speed CR clock after setting trimming value.
This period is able to use High-speed CR clock as source clock.
Document Number: 002-05631 Rev *B
Page 74 of 128
MB9AB40NB Series
Built-in Low-speed CR
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Clock frequency
12.5.4
fCRL
Value
Conditions
-
Min
50
Typ
100
Max
150
Unit
Remarks
kHz
Operating Conditions of Main and USB PLL
Operating Conditions of Main and USB PLL (In the case of using main clock for input of PLL)
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Value
Symbol
Min
Typ
Max
[1]
PLL oscillation stabilization wait time
(LOCK UP time)
PLL input clock frequency
PLL multiple rate
PLL macro oscillation clock frequency
Main PLL clock frequency[2]
USB clock frequency[3]
Unit
tLOCK
100
-
-
μs
fPLLI
fPLLO
fCLKPLL
4
5
75
-
-
16
37
150
40
MHz
multiple
MHz
MHz
fCLKSPLL
-
-
48
MHz
Remarks
After the M
frequency division
1: Time from when the PLL starts operating until the oscillation stabilizes.
2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM3 Family Peripheral Manual.
3: For more information about USB clock, see Chapter 2-2: USB Clock Generation in FM3 Family Peripheral Manual
Communication Macro Part.
Operating Conditions of Main PLL (In the case of using the built-in High-speed CR for the input
Main PLL)
clock of the
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Value
Parameter
Symbol
Min
Typ
Unit
PLL oscillation stabilization wait time[1]
(LOCK UP time)
tLOCK
100
-
-
μs
PLL input clock frequency
PLL multiple rate
PLL macro oscillation clock frequency
Main PLL clock frequency[2]
fPLLI
fPLLO
fCLKPLL
3.8
19
4
-
4.2
35
MHz
multiple
MHz
MHz
72
-
Remarks
Max
150
40
1: Time from when the PLL starts operating until the oscillation stabilizes.
2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM3 Family Peripheral Manual.
Note:
−
Make sure to input to the Main PLL source clock, the High-speed CR clock (CLKHC) that the frequency/temperature has
been trimmed. When setting PLL multiple rate, please take the accuracy of the built-in High-speed CR clock into account and
prevent the master clock from exceeding the maximum frequency.
Document Number: 002-05631 Rev *B
Page 75 of 128
MB9AB40NB Series
Main PLL connection
Main clock (CLKMO)
High-speed CR clock (CLKHC)
K
divider
PLL input
clock
Main
PLL
PLL macro
oscillation clock
Main PLL
clock
(CLKPLL)
M
divider
N
divider
USB PLL connection
Main clock (CLKMO)
K
divider
PLL input
clock
USB PLL
PLL macro
oscillation clock
USB
clock
M
divider
N
divider
12.5.5
Reset Input Characteristics
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin name
Value
Conditions
Min
Reset input time
tINITX
Document Number: 002-05631 Rev *B
INITX
-
500
Unit
Remarks
Max
-
ns
Page 76 of 128
MB9AB40NB Series
12.5.6
Power-on Reset Timing
(VSS = 0V, TA = - 40°C to + 85°C)
Value
Parameter
Symbol
Pin name
Conditions
Unit
Min
Power supply shut down time
tOFF
Power ramp rate
dV/dt
Time until releasing Power-on
reset
tPRT
VCC
Typ
Remarks
Max
1
-
-
ms
*1
Vcc:0.2 V to 1.65 V
0.2
-
1000
mV/μs
*2
-
1.34
-
16.09
ms
*1: VCC must be held below 0.2 V for minimum period of tOFF. Improper initialization may occur if this condition is not met.
*2: This dV/dt characteristic is applied at the power-on of cold start (tOFF>1 ms).
Note:
−
If tOFF cannot be satisfied designs must assert external reset(INITX) at power-up and at any brownout event per “13. 5.
5.Reset Input Characteristics”.
1.65V
VCC
VDH
0.2V
dV/dt
0.2V
tPRT
Internal RST
RST Active
CPU Operation
0.2V
tOFF
release
start
Glossary
 VDH: detection voltage of Low Voltage detection reset. See “12.8 Low-Voltage Detection Characteristics”
Document Number: 002-05631 Rev *B
Page 77 of 128
MB9AB40NB Series
12.5.7
External Bus Timing
External bus clock output characteristics
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Output frequency
Symbol
tCYCLE
Pin name
MCLKOUT*
Value
Conditions
Min
VCC ≥ 2.7 V
-
Max
40
VCC < 2.7 V
-
20
Unit
MHz
MHz
*: The external bus clock output (MCLKOUT) is a divided clock of HCLK.
For more information about setting of clock divider, see Chapter 12: External Bus Interface in FM3 Family Peripheral Manual.
When external bus clock is not output, this characteristic does not give any effect on external bus operation.
MCLKOUT
External bus signal input/output characteristics
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Conditions
VIH
Value
Unit
0.8 × VCC
V
0.2 × VCC
V
VOH
0.8 × VCC
V
VOL
0.2 × VCC
V
Remarks
Signal input characteristics
VIL
Signal output characteristics
Input signal
VIH
VIL
VIH
VIL
Output signal
VOH
VOL
VOH
VOL
Document Number: 002-05631 Rev *B
Page 78 of 128
MB9AB40NB Series
Separate Bus Access Asynchronous SRAM Mode
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
MOEX Min pulse width
Symbol
tOEW
MCSX ↓ → Address output delay
time
tCSL – AV
MOEX ↑ → Address hold time
tOEH - AX
MCSX ↓ → MOEX ↓ delay time
tCSL - OEL
Pin name
MOEX
MCSX[7:0],
MAD[24:0]
MOEX,
MAD[24:0]
MOEX, MCSX[7:0]
MOEX ↑ → MCSX ↑ time
tOEH - CSH
MCSX ↓ → MDQM ↓ delay time
tCSL - RDQML MCSX, MDQM[1:0]
Data set up → MOEX ↑ time
tDS - OE
MOEX ↑ →Data hold time
tDH - OE
MWEX Min pulse width
tWEW
MWEX
MWEX ↑ → Address output delay
time
tWEH - AX
MWEX, MAD[24:0]
MCSX ↓ → MWEX ↓ delay time
tCSL - WEL
MOEX,
MADATA[15:0]
MOEX,
MADATA[15:0]
MWEX, MCSX[7:0]
MWEX ↑ → MCSX ↑ delay time
tWEH - CSH
MCSX ↓→ MDQM ↓ delay time
tCSL-WDQML MCSX, MDQM[1:0]
MWEX ↓→ Data output time
tCSL - DV
MWEX ↑ → Data hold time
tWEH - DX
MCSX,
MADATA[15:0]
MWEX,
MADATA[15:0]
Value
Conditions
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
Min
Max
Unit
MCLK×n-3
-
-9
-12
MCLK×m-9
MCLK×m-12
30
38
+9
+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
-
0
-
ns
MCLK×n-3
-
ns
0
MCLK×m-9
MCLK×m-12
0
0
MCLK×n-9
MCLK×n-12
0
MCLK×n-9
MCLK×n-12
MCLK-9
MCLK-12
0
MCLK×m+9
MCLK×m+12
MCLK×n+9
MCLK×n+12
MCLK×m+9
MCLK×m+12
MCLK×n+9
MCLK×n+12
MCLK+9
MCLK+12
MCLK×m+9
MCLK×m+12
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note:
−
When the external load capacitance CL = 30 pF (m = 0 to 15, n = 1 to 16).
Document Number: 002-05631 Rev *B
Page 79 of 128
MB9AB40NB Series
MCLK
MCSX[7:0]
MAD[24:0]
MOEX
MDQM[1:0]
MWEX
MADATA[15:0]
Document Number: 002-05631 Rev *B
Page 80 of 128
MB9AB40NB Series
Separate Bus Access Synchronous SRAM Mode
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Address delay time
Symbol
tAV
Pin name
MCLK, MAD[24:0]
tCSL
MCSX delay time
MCLK, MCSX[7:0]
tCSH
tREL
MOEX delay time
MCLK, MOEX
tREH
Data set up → MCLK ↑ time
tDS
MCLK, MADATA[15:0]
MCLK ↑ → Data hold time
tDH
MCLK, MADATA[15:0]
tWEL
MWEX delay time
MCLK, MWEX
tWEH
tDQML
MDQM[1:0] delay time
MCLK, MDQM[1:0]
tDQMH
MCLK ↑ → Data output time
tODS
MCLK, MADATA[15:0]
MCLK ↑ → Data hold time
tOD
MCLK, MADATA[15:0]
Value
Conditions
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC<2.7 V
VCC ≥ 2.7 V
VCC<2.7 V
Min
Max
Unit
1
12
13
ns
1
12
ns
1
12
ns
1
1
9
12
9
12
ns
ns
24
37
-
ns
0
-
ns
1
1
1
1
MCLK + 1
1
9
12
9
12
9
12
9
12
MCLK + 18
MCLK + 24
18
24
ns
ns
ns
ns
ns
ns
Note:
−
When the external load capacitance CL = 30 pF.
MCLK
MCSX[7:0]
MAD[24:0]
MOEX
MDQM[1:0]
MWEX
MADATA[15:0]
Document Number: 002-05631 Rev *B
Page 81 of 128
MB9AB40NB Series
Multiplexed Bus Access Asynchronous SRAM Mode
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Multiplexed address delay
time
Multiplexed address hold
time
Symbol
Pin name
tALE-CHMADV
MALE, MADATA[15:0]
tCHMADH
Value
Conditions
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
Min
-2
MCLK×n+0
MCLK×n+0
Max
+10
+20
MCLK×n+10
MCLK×n+20
Unit
ns
ns
Note:
−
When the external load capacitance CL = 30 pF (m = 0 to 15, n = 1 to 16).
MCLK
MCSX[7:0]
MALE
MAD [24:0]
MOEX
MDQM [1:0]
MWEX
MADATA[15:0]
Document Number: 002-05631 Rev *B
Page 82 of 128
MB9AB40NB Series
Multiplexed Bus Access Synchronous SRAM Mode
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin name
tCHAL
MALE delay time
MCLK, ALE
tCHAH
MCLK ↑ → Multiplexed
Address delay time
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
Min
Max
Unit
9
12
9
12
ns
ns
ns
ns
1
tOD
ns
1
tOD
ns
1
1
Remarks
VCC ≥ 2.7 V
tCHMADV
MCLK,
MADATA[15:0]
MCLK ↑ → Multiplexed
Data output time
Value
Conditions
VCC < 2.7 V
VCC ≥ 2.7 V
tCHMADX
VCC < 2.7 V
Note:
−
When the external load capacitance CL = 30 pF.
MCLK
MCSX[7:0]
MALE
MAD [24:0]
MOEX
MDQM [1:0]
MWEX
MADATA[15:0]
Document Number: 002-05631 Rev *B
Page 83 of 128
MB9AB40NB Series
External Ready Input Timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
MCLK ↑ MRDY input
setup time
Symbol
tRDYI
Pin name
Value
Conditions
Min
VCC ≥ 2.7 V
23
VCC < 2.7 V
37
MCLK, MRDY
Max
-
Unit
Remarks
ns
When RDY is input
···
MCLK
Over 2cycles
Original
MOEX
MWEX
tRDYI
MRDY
When RDY is released
MCLK
··· ···
2 cycles
Extended
MOEX
MWEX
tRDYI
0.5×VCC
MRDY
Document Number: 002-05631 Rev *B
Page 84 of 128
MB9AB40NB Series
12.5.8
Base Timer Input Timing
Timer input timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Input pulse width
Symbol
tTIWH,
tTIWL
Pin name
Value
Conditions
TIOAn/TIOBn
(when using as
ECK, TIN)
-
Min
2tCYCP
tTIWH
Max
-
Unit
Remarks
ns
tTIWL
ECK
VIHS
TIN
VIHS
VILS
VILS
Trigger input timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Input pulse width
Symbol
tTRGH,
tTRGL
Pin name
TIOAn/TIOBn
(when using as
TGIN)
-
VIHS
Min
2tCYCP
tTRGH
TGIN
Value
Conditions
Max
-
Unit
Remarks
ns
tTRGL
VIHS
VILS
VILS
Note:
−
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which the Base Timer is connected to, see Block Diagram in this data sheet.
Document Number: 002-05631 Rev *B
Page 85 of 128
MB9AB40NB Series
12.5.9
CSIO/UART Timing
CSIO (SPI = 0, SCINV = 0)
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Baud rate
Serial clock cycle time
tSCYC
SCK ↓ → SOT delay time
tSLOVI
Pin
name
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
Min
-
Master mode
VCC ≥ 2.7 V
VCC < 2.7 V
Conditions
Max
-
8
Min
Max
8
Unit
4tCYCP
-
4tCYCP
-
Mbps
ns
- 30
+ 30
- 20
+ 20
ns
50
-
36
-
ns
0
-
0
-
ns
SIN → SCK ↑ setup time
tIVSHI
SCK ↑ → SIN hold time
tSHIXI
Serial clock L pulse width
tSLSH
SCKx
2tCYCP - 10
-
2tCYCP - 10
-
ns
Serial clock H pulse width
tSHSL
SCKx
tCYCP + 10
-
tCYCP + 10
-
ns
-
50
-
33
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
SCK ↓ → SOT delay time
tSLOVE
SIN → SCK ↑ setup time
tIVSHE
SCK ↑ → SIN hold time
tSHIXE
SCK falling time
SCK rising time
tF
tR
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
Slave mode
Notes:
−
−
The above characteristics apply to clock synchronous mode.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Multi-function serial is connected to, see Block Diagram in this
data sheet.
Document Number: 002-05631 Rev *B
Page 86 of 128
MB9AB40NB Series
tSCYC
VOH
SCK
VOH
VOL
tSHOVI
VOH
VOL
SOT
tIVSLI
VIH
VIL
SIN
tSLIXI
VIH
VIL
Master mode
tSHSL
SCK
VIH
tSLSH
VIH
VIL
tR
tF
VIL
VIL
tSHOVE
SOT
VOH
VOL
tIVSLE
SIN
VIH
VIL
tSLIXE
VIH
VIL
Slave mode
Document Number: 002-05631 Rev *B
Page 87 of 128
MB9AB40NB Series
CSIO (SPI = 0, SCINV = 1)
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Symbol
Pin
name
Baud rate
Serial clock cycle time
tSCYC
SCKx
SCK ↑ → SOT delay time
tSHOVI
SCKx,
SOTx
SIN → SCK ↓ setup time
tIVSLI
SCK ↓ → SIN hold time
tSLIXI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK ↑ → SOT delay time
tSHOVE
SIN → SCK ↓ setup time
tIVSLE
SCK ↓ → SIN hold time
tSLIXE
SCK falling time
SCK rising time
tF
tR
Parameter
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
-
VCC ≥ 2.7 V
VCC < 2.7 V
Conditions
Min
Max
8
Min
Max
8
Unit
4tCYCP
-
4tCYCP
-
Mbps
ns
- 30
+ 30
- 20
+ 20
ns
50
-
36
-
ns
0
-
0
-
ns
2tCYCP - 10
tCYCP + 10
-
2tCYCP - 10
tCYCP + 10
-
ns
ns
-
50
-
33
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Master mode
Slave mode
Notes:
−
The above characteristics apply to clock synchronous mode.
−
−
−
tCYCP indicates the APB bus clock cycle time.
−
When the external load capacitance CL = 30 pF.
About the APB bus number which Multi-function serial is connected to, see Block Diagram in this data sheet.
These characteristics only guarantee the same relocate port number.For example, the combination of
SCKx_0 and SOTx_1 is not guaranteed.
Document Number: 002-05631 Rev *B
Page 88 of 128
MB9AB40NB Series
tSCYC
SCK
VOH
VOH
VOL
tSHOVI
VOH
VOL
SOT
tIVSLI
VIH
SIN
tSLIXI
VIH
VIL
VIL
Master mode
tSHSL
SCK
VIH
tSLSH
VIH
VIL
tR
tF
VIL
VIL
tSHOVE
SOT
VOH
VOL
tIVSLE
SIN
VIH
VIL
tSLIXE
VIH
VIL
Slave mode
Document Number: 002-05631 Rev *B
Page 89 of 128
MB9AB40NB Series
CSIO (SPI = 1, SCINV = 0)
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin
name
Baud rate
Serial clock cycle time
tSCYC
SCKx
SCK ↑ → SOT delay time
tSHOVI
SCKx,
SOTx
SIN → SCK ↓ setup time
tIVSLI
SCK ↓→ SIN hold time
tSLIXI
SOT → SCK ↓ delay time
tSOVLI
Serial clock L pulse width
Serial clock H pulse width
tSLSH
tSHSL
SCK ↑ → SOT delay time
tSHOVE
SIN → SCK ↓ setup time
tIVSLE
SCK ↓→ SIN hold time
tSLIXE
SCK falling time
SCK rising time
tF
tR
SCKx,
SINx
SCKx,
SINx
SCKx,
SOTx
SCKx
SCKx
SCKx,
SOTx
SCKx,
SINx
SCKx,
SINx
SCKx
SCKx
-
Master
mode
Slave mode
VCC ≥ 2.7 V
VCC < 2.7 V
Conditions
Min
Max
8
Min
Max
8
Unit
4tCYCP
-
4tCYCP
-
Mbps
ns
- 30
+ 30
- 20
+ 20
ns
50
-
36
-
ns
0
-
0
-
ns
2tCYCP - 34
-
2tCYCP - 34
-
ns
2tCYCP - 10
tCYCP + 10
-
2tCYCP - 10
tCYCP + 10
-
ns
ns
-
50
-
33
ns
10
-
10
-
ns
20
-
20
-
ns
-
5
5
-
5
5
ns
ns
Notes:
−
−
−
The above characteristics apply to clock synchronous mode.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
tCYCP indicates the APB bus clock cycle time.
About the APB bus number which Multi-function serial is connected to, see Block Diagram in this
data sheet.
Document Number: 002-05631 Rev *B
Page 90 of 128
MB9AB40NB Series
tSCYC
VOH
SCK
VOL
SOT
VOH
VOL
VOH
VOL
tIVSLI
tSLIXI
VIH
VIL
SIN
VOL
tSHOVI
tSOVLI
VIH
VIL
Master mode
tSLSH
VIH
SCK
SOT
VIL
VIL
tF
*
VOH
VOL
tR
tIVSLE
SIN
tSHSL
VIH
VIH
tSHOVE
VOH
VOL
tSLIXE
VIH
VIL
VIH
VIL
Slave mode
*: Changes when writing to TDR register
Document Number: 002-05631 Rev *B
Page 91 of 128
MB9AB40NB Series
CSIO (SPI = 1, SCINV = 1)
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin name
Conditions
-
-
Baud rate
Serial clock cycle time
tSCYC
SCKx
SCK ↓ → SOT delay time
tSLOVI
SCKx, SOTx
SIN → SCK ↑ setup time
SCK ↑ → SIN hold time
SOT → SCK ↑ delay time
Serial clock L pulse width
Serial clock H pulse width
SCK ↓ → SOT delay time
SIN → SCK ↑ setup time
SCK ↑ → SIN hold time
SCK falling time
SCK rising time
tIVSHI
tSHIXI
tSOVHI
tSLSH
tSHSL
tSLOVE
tIVSHE
tSHIXE
tF
tR
SCKx, SINx
SCKx, SINx
SCKx, SOTx
SCKx
SCKx
SCKx, SOTx
SCKx, SINx
SCKx, SINx
SCKx
SCKx
Master
mode
Slave mode
VCC ≥ 2.7 V
VCC < 2.7 V
Min
Max
8
Min
Max
8
Unit
4tCYCP
-
4tCYCP
-
Mbps
ns
- 30
+ 30
- 20
+ 20
ns
50
0
2tCYCP - 34
2tCYCP - 10
tCYCP + 10
10
20
-
50
5
5
36
0
2tCYCP - 34
2tCYCP - 10
tCYCP + 10
10
20
-
33
5
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes:
−
The above characteristics apply to clock synchronous mode.
−
−
tCYCP indicates the APB bus clock cycle time.
−
These characteristics only guarantee the same relocate port number.
For example, the combination of SCKx_0 and SOTx_1 is not guaranteed.
−
When the external load capacitance CL = 30 pF.
About the APB bus number which Multi-function serial is connected to, see Block Diagram in this data sheet.
Document Number: 002-05631 Rev *B
Page 92 of 128
MB9AB40NB Series
tSCYC
VOH
SCK
VOH
VOL
tSOVHI
tSLOVI
VOH
VOL
SOT
VOH
VOL
tSHIXI
tIVSHI
VIH
VIL
SIN
VIH
VIL
Master mode
tR
SCK
tF
tSHSL
VIH
VIH
VIL
tSLSH
VIL
VIL
tSLOVE
VOH
VOL
SOT
VOH
VOL
tIVSHE
tSHIXE
VIH
VIL
SIN
VIH
VIL
Slave mode
UART external clock input (EXT = 1)
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Serial clock L pulse width
Serial clock H pulse width
SCK falling time
SCK rising time
Symbol
tSLSH
tSHSL
tF
tR
Min
tCYCP + 10
tCYCP + 10
-
CL = 30 pF
Unit
Max
5
5
Remarks
ns
ns
ns
ns
tF
tR
t
t
SHSL
SCK
VIL
Document Number: 002-05631 Rev *B
Value
Conditions
V
IH
V
IH
V IL
SLSH
VIL
V
IH
Page 93 of 128
MB9AB40NB Series
12.5.10 External Input Timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin name
ADTG
Input pulse width
tINH,
tINL
INTxx,
NMIX
WKUPx
Conditions
Value
Unit
Remarks
Min
Max
-
2tCYCP[1]
-
ns
A/D converter trigger input
[2]
2tCYCP + 100[1]
-
ns
[3]
500
600
-
ns
ns
External interrupt
NMI
[4]
Deep standby wake up
1: tCYCP indicates the APB bus clock cycle time.
About the APB bus number which the Multi-function Timer is connected to, see Block Diagramin this data sheet.
2: When in Run mode, in Sleep mode.
3: When in Timer mode, in RTC mode, in Stop mode.
4: When in Deep Standby RTC mode, in Deep Standby Stop mode.
Document Number: 002-05631 Rev *B
Page 94 of 128
MB9AB40NB Series
12.5.11 I2C Timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
SCL clock frequency
(Repeated) START condition
hold time SDA ↓ → SCL ↓
SCL clock L width
SCL clock H width
(Repeated) START condition
setup time SCL ↑ → SDA ↓
Data hold time SCL ↓ → SDA
↓↑
Data setup time SDA ↓ ↑ →
SCL ↑
STOP condition setup time
SCL ↑ → SDA ↑
Bus free time between STOP
condition and START condition
Noise filter
Symbol
Standard-mode
Conditions
Fast-mode
fSCL
0
0
Max
400
tHDSTA
4.0
-
0.6
-
μs
tLOW
tHIGH
4.7
4.0
-
1.3
0.6
-
μs
μs
4.7
-
0.6
-
μs
0
3.45[2]
0
0.9[3]
μs
tSUDAT
250
-
100
-
ns
tSUSTO
4.0
-
0.6
-
μs
tBUF
4.7
-
1.3
-
μs
-
ns
tHDDAT
tSP
CL = 30 pF,
R = (Vp/IOL)[1]
-
2
tCYCP[4]
-
Min
Unit
Max
100
tSUSTA
Min
2
tCYCP[4]
kHz
Remarks
1: R and C represent the pull-up resistor and load capacitance of the SCL and SDA lines, respectively.
Vp indicates the power supply voltage of the pull-up resistor and IOL indicates VOL guaranteed current.
2: The maximum tHDDAT must satisfy that it does not extend at least L period (tLOW) of device's SCL signal.
3: A Fast-mode I2C bus device can be used on a Standard-mode I2C bus system as long as the device satisfies the requirement of
tSUDAT ≥ 250 ns.
4: tCYCP is the APB bus clock cycle time.About the APB bus number that I 2C is connected to, see Block Diagram in this data sheet.
To use Standard-mode, set the APB bus clock at 2 MHz or more.To use Fast-mode, set the APB bus clock at 8 MHz or more.
SDA
SCL
Document Number: 002-05631 Rev *B
Page 95 of 128
MB9AB40NB Series
12.5.12 ETM Timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Data hold
TRACECLK
frequency
Symbol
tETMH
Pin name
TRACECLK,
TRACED[3:0]
Min
Max
Unit
VCC ≥ 2.7 V
2
11
VCC < 2.7 V
2
15
VCC ≥ 2.7 V
-
40
MHz
VCC < 2.7 V
-
20
MHz
VCC ≥ 2.7 V
25
-
ns
VCC < 2.7 V
50
-
ns
Remarks
ns
1/ tTRACE
TRACECLK
TRACECLK
clock cycle
Value
Conditions
tTRACE
Note:
−
When the external load capacitance CL = 30 pF.
HCLK
TRACECLK
TRACED[3:0]
Document Number: 002-05631 Rev *B
Page 96 of 128
MB9AB40NB Series
12.5.13 JTAG Timing
(VCC = 1.65V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin name
Value
Conditions
TMS, TDI setup time
tJTAGS
TCK,
TMS, TDI
VCC ≥ 2.7 V
TMS, TDI hold time
tJTAGH
TCK,
TMS, TDI
VCC ≥ 2.7 V
TDO delay time
tJTAGD
TCK,
TDO
Min
Max
Unit
15
-
ns
15
-
ns
VCC ≥ 2.7 V
-
25
VCC < 2.7 V
-
45
VCC < 2.7 V
VCC < 2.7 V
Remarks
ns
Note:
−
When the external load capacitance CL = 30 pF.
TCK
TMS/TDI
TDO
Document Number: 002-05631 Rev *B
Page 97 of 128
MB9AB40NB Series
12.6
12-bit A/D Converter
Electrical Characteristics for the A/D Converter
(VCC = AVCC = 1.65V to 3.6V, VSS = AVSS = 0V, TA = - 40°C to + 85°C)
Parameter
Resolution
Integral Nonlinearity
Differential Nonlinearity
Zero transition voltage
Full-scale transition
voltage
Value
Pin
name
Symbol
Min
VZT
ANxx
-
VFST
ANxx
-
±2
± 2.2
±6
AVRH ± 6
[1]
Conversion time
-
-
Sampling time[2]
tS
-
Compare clock cycle[3]
State transition time to
operation permission
Power supply current
(analog + digital)
Reference power supply
current
(between AVRH to
AVSS)
Analog input capacity
Typ
Unit
Max
12
± 4.5
± 2.5
± 15
AVRH ±
15
-
bit
LSB
LSB
mV
10
us
mV
2.0
4.0[1]
10[1]
0.6
-
1.2
-
3.0
100
200
500
-
1000
ns
-
tSTT
-
-
-
1.0
μs
-
AVCC
-
0.27
0.03
0.42
10
mA
μA
-
0.72
1.29
mA
-
AVRH
-
0.02
2.6
μA
-
-
9.4
pF
-
AVCC ≥ 2.7 V
1.8 V< AVCC < 2.7 V
1.65 V< AVCC < 1.8 V
AVCC ≥ 2.7 V
μs
tCCK
CAIN
1.8 V< AVCC < 2.7 V
1.65V< AVCC < 1.8V
AVCC ≥ 2.7 V
1.8 V< AVCC < 2.7 V
1.65 V< AVCC < 1.8 V
A/D 1unit operation
When A/D stops
A/D 1unit operation
AVRH=3.6 V
When A/D stops
AVCC ≥ 2.7V
2.2
Analog input resistor
Interchannel disparity
Analog port input leak
current
Analog input voltage
Reference voltage
RAIN
-
-
-
5.5
kΩ
LSB
-
-
-
-
10.5
4
-
ANxx
-
-
5
μA
-
ANxx
AVSS
-
AVRH
V
AVRH
2.7
AVCC
-
AVCC
V
-
AVRL
AVSS
-
Remarks
AVSS
1.8 V< AVCC < 2.7 V
1.65 V< AVCC < 1.8 V
AVCC ≥ 2.7 V
AVCC < 2.7 V
V
1: The conversion time is the value of sampling time (tS) + compare time (tC).
The condition of the minimum conversion time is the following.
AVCC ≥ 2.7 V,
HCLK=40 MHz sampling time: 0.6 μs, compare time: 1.4 μs
1.8 V < AVCC < 2.7 V,
HCLK=40 MHz sampling time: 1.2 μs, compare time: 2.8 μs
1.65 V < AVCC < 1.8 V, HCLK=40 MHz sampling time: 3 μs, compare time: 7 μs
Ensure that it satisfies the value of the sampling time (tS) and compare clock cycle (tCCK).
For setting of the sampling time and the compare clock cycle, see Chapter 1-1: A/D Converter in FM3 Family Peripheral Manual
Analog Macro Port.
The register setting of the A/D Converter are reflected in the operation according to the APB bus clock timing.
The sampling clock and compare clock is generated from the Base clock (HCLK).
About the APB bus number which the A/D Converter is connected to, see Block Diagram in this data sheet.
2: A necessary sampling time changes by external impedance.
Ensure that it set the sampling time to satisfy (Equation 1).
3: The compare time (tC) is the value of (Equation 2).
Document Number: 002-05631 Rev *B
Page 98 of 128
MB9AB40NB Series
REXT
ANxx
Analog input pin
Comparator
RAIN
Analog
signal source
CAIN
(Equation 1) tS ≥ ( RAIN + REXT ) × CAIN × 9
tS:
Sampling time[ns]
RAIN:
Input resistor of A/D[kΩ] = 2.2 kΩ at 2.7 V < AVCC < 3.6 V
Input resistor of A/D[kΩ] = 5.5 kΩ at 1.8 V < AVCC < 2.7 V
Input resistor of A/D[kΩ] = 10.5 kΩ at 1.65 V < AVCC < 1.8 V
CAIN:
Input capacity of A/D[pF] = 9.4 pF at 1.65 V < AVCC < 3.6 V
REXT:
Output impedance of external circuit[kΩ]
(Equation 2) tC = tCCK × 14
tC:
Compare time
tCCK:
Compare clock cycle
Document Number: 002-05631 Rev *B
Page 99 of 128
MB9AB40NB Series
Definition of 12-bit A/D Converter Terms
 Resolution:
Analog variation that is recognized by an A/D converter.
 Integral Nonlinearity:
Deviation of the line between the zero-transition point
(0b000000000000 ←→ 0b000000000001) and the full-scale transition
point (0b111111111110 ←→ 0b111111111111) from the actual conversion
characteristics.
 Differential Nonlinearity:
Deviation from the ideal value of the input voltage that is required to
change the output code by 1 LSB.
Integral Nonlinearity
Differential Nonlinearity
0xFFF
Actual conversion
characteristics
0xFFE
0x(N+1)
{1 LSB(N-1) + VZT}
VFST
VNT
0x004
(Actually-measured
value)
0x003
0x002
(Actuallymeasured
value)
Digital output
Digital output
0xFFD
0xN
Actual conversion
characteristics
Ideal characteristics
(Actually-measured
value)
Actual conversion
characteristics
Ideal characteristics
VNT
(Actually-measured
value)
0x(N-2)
0x001
VZT (Actually-measured value)
AVSS
Actual conversion characteristics
AVRH
AVSS
Analog input
Linearity error of digital output N =
AVRH
Analog input
VNT - {1LSB × (N - 1) + VZT}
1LSB
Differential linearity error of digital output N =
1LSB =
V(N+1)T
0x(N-1)
V(N + 1) T - VNT
1LSB
[LSB]
- 1 [LSB]
VFST - VZT
4094
N:
A/D converter digital output value.
Voltage at which the digital output changes from 0x000 to 0x001.
VFST: Voltage at which the digital output changes from 0xFFE to 0xFFF.
VNT: Voltage at which the digital output changes from 0x(N − 1) to 0xN.
VZT:
Document Number: 002-05631 Rev *B
Page 100 of 128
MB9AB40NB Series
12.7
USB Characteristics
(VCC = 3.0V to 3.6V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Input H level voltage
Input L level voltage
Input
characteristics Differential input
sensitivity
Different common mode
range
Symbol
Value
Conditions
Min
Max
Unit
Remarks
VIH
-
2.0
VCC + 0.3
V
[1]
VIL
-
VSS - 0.3
0.8
V
[1]
VDI
-
0.2
-
V
[2]
VCM
-
0.8
2.5
V
[2]
2.8
3.6
V
[3]
0
0.3
V
[3]
1.3
4
4
2.0
20
20
V
ns
ns
[4]
VCRS
tFR
tFF
External
pull-down
resistor = 15kΩ
External
pull-up resistor
= 1.5kΩ
Full-Speed
Full-Speed
tFRFM
Full-Speed
90
111.11
%
[5]
ZDRV
tLR
tLF
Full-Speed
Low-Speed
Low-Speed
28
75
75
44
300
300
Ω
ns
ns
[5]
tLRFM
Low-Speed
80
125
%
[7]
Output H level voltage
VOH
Output L level voltage
VOL
Crossover voltage
Rising time
Output
characteristics Falling time
Rising/falling time
matching
Output impedance
Rising time
Falling time
Rising/falling time
matching
Pin
name
UDP0,
UDM0
[5]
[5]
[7]
[7]
1: The switching threshold voltage of Single-End-Receiver of USB I/O buffer is set as within VIL (Max) = 0.8V, VIH (Min) = 2.0 V
(TTL input standard). There are some hysteresis to lower noise sensitivity.
Minimum differential input
sensitivity [V]
2: Use the differential-Receiver to receive the USB differential data signal.
The Differential-Receiver has 200 mV of differential input sensitivity when the differential data input is within 0.8 V to 2.5 V to the
local ground reference level. Above voltage range is the common mode input voltage range.
Common mode input voltage [V]
3: The output drive capability of the driver is below 0.3 V at Low-State (VOL) (to 3.6 V and 1.5 kΩ load), and 2.8 V or above (to
ground and 15 kΩ load) at High-State (VOH).
4: The cross voltage of the external differential output signal (D + /D − ) of USB I/O buffer is within 1.3 V to 2.0 V.
Document Number: 002-05631 Rev *B
Page 101 of 128
MB9AB40NB Series
VCRS specified range
5: They indicate the rising time (Trise) and falling time (Tfall) of the full-speed differential data signal.
They are defined by the time between 10% and 90% of the output signal voltage.
For full-speed buffer, Tr/Tf ratio is regulated as within ± 10% to minimize RFI emission.
Rising time
Falling time
6: USB Full-speed connection is performed via twist pair cable shield with 90Ω ± 15% characteristic impedance (Differential Mode).
USB standard defines that output impedance of USB driver must be in range from 28 Ω to 44 Ω. So, discrete series resistor (Rs)
addition is defined in order to satisfy the above definition and keep balance.
When using this USB I/O, use it with 25 Ω to 30 Ω (recommendation value 27 Ω) Series resistor Rs.
Document Number: 002-05631 Rev *B
Page 102 of 128
MB9AB40NB Series
28Ω to 44Ω Equiv. Imped.
28Ω to 44Ω Equiv. Imped.
Mount it as external resistor.
Rs series resistor 25Ω to 30Ω
Series resistor of 27Ω (recommendation value) must be added.
And, use resistance with an uncertainty of 5% by E24 sequence.
7: They indicate the rising time (Trise) and falling time (Tfall) of the low-speed differential data signal.They are defined by the time
between 10% and 90% of the output signal voltage.
Rising time
Falling time
See Figure  Low-Speed Load (Compliance Load) for conditions of the external load.
Document Number: 002-05631 Rev *B
Page 103 of 128
MB9AB40NB Series
Low-Speed Load (Upstream Port Load) - Reference 1
CL = 50pF to 150pF
CL = 50pF to 150pF
Low-Speed Load (Downstream Port Load) - Reference 2
CL =
200pF to 600pF
CL =
200pF to 600pF
Low-Speed Load (Compliance Load)
CL = 200pF to 450pF
CL = 200pF to 450pF
Document Number: 002-05631 Rev *B
Page 104 of 128
MB9AB40NB Series
12.8
Low-Voltage Detection Characteristics
Low-Voltage Detection Reset
(TA = - 40°C to + 85°C)
Parameter
Symbol
Conditions
Value
Typ
Min
Max
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
SVHR[1] = 00000
LVD stabilization
wait time
tLVDW
-
-
-
5200 × tCYCP[2]
μs
LVD detection delay
time
tLVDDL
-
-
-
200
μs
SVHR[1] = 00001
SVHR[1] = 00010
SVHR[1] = 00011
SVHR[1] = 00100
SVHR[1] = 00101
SVHR[1] = 00110
SVHR[1] = 00111
SVHR[1] = 01000
SVHR[1] = 01001
SVHR[1] = 01010
SVHR[1] = 01011
SVHR[1] = 01100
SVHR[1] = 01101
SVHR[1] = 01110
SVHR[1] = 01111
SVHR[1] = 10000
SVHR[1] = 10001
SVHR[1] = 10010
SVHR[1] = 10011
1.38
1.50
1.60
1.43
1.55
1.65
1.43
1.55
1.65
Same as SVHR = 00000 value
1.47
1.60
1.73
Same as SVHR = 00000 value
1.52
1.65
1.78
Same as SVHR = 00000 value
1.56
1.70
1.84
Same as SVHR = 00000 value
1.61
1.75
1.89
Same as SVHR = 00000 value
1.66
1.80
1.94
Same as SVHR = 00000 value
1.70
1.85
2.00
Same as SVHR = 00000 value
1.75
1.90
2.05
Same as SVHR = 00000 value
1.79
1.95
2.11
Same as SVHR = 00000 value
1.84
2.00
2.16
Same as SVHR = 00000 value
1.89
2.05
2.21
Same as SVHR = 00000 value
2.30
2.50
2.70
Same as SVHR = 00000 value
2.39
2.60
2.81
Same as SVHR = 00000 value
2.48
2.70
2.92
Same as SVHR = 00000 value
2.58
2.80
3.02
Same as SVHR = 00000 value
2.67
2.90
3.13
Same as SVHR = 00000 value
2.76
3.00
3.24
Same as SVHR = 00000 value
2.85
3.10
3.35
Same as SVHR = 00000 value
2.94
3.20
3.46
Same as SVHR = 00000 value
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Remarks
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
1: The SVHR bit of Low-Voltage Detection Voltage Control Register (LVD_CTL) is initialized to 00000 by Low-Voltage Detection
Reset.
2: tCYCP indicates the APB2 bus clock cycle time.
Document Number: 002-05631 Rev *B
Page 105 of 128
MB9AB40NB Series
12.8.1
Interrupt of Low-Voltage Detection
(TA = - 40°C to + 85°C)
Parameter
Symbol
Conditions
Value
Max
Unit
Min
1.56
1.61
1.61
1.66
1.66
1.70
1.70
1.75
1.75
1.79
1.79
1.84
1.84
1.89
1.89
1.93
2.30
2.39
2.39
2.48
2.48
2.58
2.58
2.67
2.67
2.76
2.76
2.85
2.85
2.94
2.94
3.04
Typ
1.70
1.75
1.75
1.80
1.80
1.85
1.85
1.90
1.90
1.95
1.95
2.00
2.00
2.05
2.05
2.10
2.50
2.60
2.60
2.70
2.70
2.80
2.80
2.90
2.90
3.00
3.00
3.10
3.10
3.20
3.20
3.30
1.84
1.89
1.89
1.94
1.94
2.00
2.00
2.05
2.05
2.11
2.11
2.16
2.16
2.21
2.21
2.27
2.70
2.81
2.81
2.92
2.92
3.02
3.02
3.13
3.13
3.24
3.24
3.35
3.35
3.46
3.46
3.56
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
Detected voltage
Released voltage
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
VDL
VDH
LVD stabilization wait
time
tLVDW
-
-
-
5200 × tCYCP*
μs
LVD detection delay
time
tLVDDL
-
-
-
200
μs
SVHI = 00100
SVHI = 00101
SVHI = 00110
SVHI = 00111
SVHI = 01000
SVHI = 01001
SVHI = 01010
SVHI = 01011
SVHI = 01100
SVHI = 01101
SVHI = 01110
SVHI = 01111
SVHI = 10000
SVHI = 10001
SVHI = 10010
SVHI = 10011
Remarks
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
When voltage drops
When voltage rises
*: tCYCP indicates the APB2 bus clock cycle time.
Document Number: 002-05631 Rev *B
Page 106 of 128
MB9AB40NB Series
12.9 Flash Memory Write/Erase Characteristics
12.9.1
Write / Erase time
(VCC = 1.65V to 3.6V, TA = - 40°C to + 85°C)
Value
Parameter
Typ*
Large Sector
1.1
2.7
Small Sector
0.3
0.9
Half word (16-bit)
write time
30
Chip erase time
6.8
Sector erase
time
Unit
Max*
Remarks
s
Includes write time prior to internal erase
528
μs
Not including system-level overhead time
18
s
Includes write time prior to internal erase
*: The typical value is immediately after shipment, the maximam value is guarantee value under 10,000 cycle of erase/write.
12.9.2
Write cycles and data hold time
Erase/write cycles (cycle)
Data hold time (year)
1,000
20*
10,000
10*
Remarks
*: At average + 85C
Document Number: 002-05631 Rev *B
Page 107 of 128
MB9AB40NB Series
12.10
Return Time from Low-Power Consumption Mode
12.10.1 Return Factor: Interrupt/WKUP
The return time from Low-Power consumption mode is indicated as follows. It is from receiving the return factor to starting the
program operation.
Return Count Time
(VCC = 1.65V to 3.6V, VDDI = 1.1V to 1.3V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Value
Symbol
Sleep mode
High-speed CR Timer mode,
Main Timer mode,
PLL Timer mode
Typ
Max*
40
80
μs
350
700
μs
690
880
μs
278
523
μs
318
278
603
523
μs
μs
tICNT
Sub Timer mode
RTC mode,
Stop mode
Deep Standby RTC mode
Deep Standby Stop mode
Remarks
μs
tCYCC
Low-speed CR Timer mode
Unit
When RAM is off
When RAM is on
*: The maximum value depends on the accuracy of built-in CR.
Operation example of return from Low-Power consumption mode (by external interrupt*)
External
interrupt
Interrupt factor
accept
Active
tICNT
CPU
Operation
Interrupt factor
clear by CPU
Start
*: External interrupt is set to detecting fall edge.
Document Number: 002-05631 Rev *B
Page 108 of 128
MB9AB40NB Series
Operation example of return from Low-Power consumption mode (by internal resource interrupt*)
Internal
resource
interrupt
Interrupt factor
accept
Active
tICNT
Interrupt factor
clear by CPU
CPU
Operation
Start
*: Internal resource interrupt is not included in return factor by the kind of Low-Power consumption mode.
Notes:
−
When interrupt recoveries, the operation mode that CPU recoveries depend on the state before the
Low-Power consumption mode transition. See Chapter 6: Low Power Consumption Mode in FM3
Family Peripheral Manual.
12.10.2 Return Factor: Reset
The return time from Low-Power consumption mode is indicated as follows. It is from releasing reset to starting the program
operation.
Return Count Time
(VCC = 1.65V to 3.6V, VDDI = 1.1V to 1.3V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Value
Symbol
Typ
Max*
Unit
148
263
μs
148
263
μs
258
483
μs
Sub Timer mode
322
516
μs
RTC/Stop mode
278
523
μs
Deep Standby RTC mode
Deep Standby Stop mode
318
278
603
523
μs
μs
Sleep mode
High-speed CR Timer mode,
Main Timer mode,
PLL Timer mode
Low-speed CR Timer mode
tRCNT
Remarks
When RAM is off
When RAM is on
*: The maximum value depends on the accuracy of built-in CR.
Document Number: 002-05631 Rev *B
Page 109 of 128
MB9AB40NB Series
Operation example of return from Low-Power consumption mode (by INITX)
INITX
Internal reset
Reset active
Release
tRCNT
CPU
Operation
Start
Operation example of return from low power consumption mode (by internal resource reset*)
Internal
resource
reset
Internal reset
Reset active
Release
tRCNT
CPU
Operation
Start
*: Internal resource reset is not included in return factor by the kind of Low-Power consumption mode.
Notes:
−
The return factor is different in each Low-Power consumption modes.
See Chapter 6: Low Power Consumption Mode and Operations of Standby Modes in FM3
Family Peripheral Manual.
−
When interrupt recoveries, the operation mode that CPU recoveries depend on the state before
the Low-Power consumption mode transition. See Chapter 6: Low Power Consumption Mode in
FM3 Family Peripheral Manual.
−
The time during the power-on reset/low-voltage detection reset is excluded. See (6) Power-on
Reset Timing in 4. AC Characteristics in Electrical Characteristics for the detail on the time
during the power-on reset/low-voltage detection reset.
−
When in recovery from reset, CPU changes to the High-speed CR Run mode. When using the
main clock or the PLL clock, it is necessary to add the main clock oscillation stabilization wait
time or the Main PLL clock stabilization wait time.
−
The internal resource reset means the watchdog reset and the CSV reset.
Document Number: 002-05631 Rev *B
Page 110 of 128
MB9AB40NB Series
13.
Ordering Information
Part number
On-chip Flash memory
On-chip SRAM
MB9AFB41LBPMC1-G-JNE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42LBPMC1-G-JNE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44LBPMC1-G-JNE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41LBPMC-G-JNE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42LBPMC-G-JNE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44LBPMC-G-JNE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41LBQN-G-AVE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42LBQN-G-AVE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44LBQN-G-AVE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41MBPMC-G-JNE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42MBPMC-G-JNE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44MBPMC-G-JNE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41MBPMC1-G-JNE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42MBPMC1-G-JNE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44MBPMC1-G-JNE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41MBBGL-GE1
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42MBBGL-GE1
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44MBBGL-GE1
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41NBPMC-G-JNE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42NBPMC-G-JNE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44NBPMC-G-JNE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41NBPQC-G-JNE2
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42NBPQC-G-JNE2
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44NBPQC-G-JNE2
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
MB9AFB41NBBGL-GE1
Main: 64 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB42NBBGL-GE1
Main: 128 Kbyte Work: 32 Kbyte
16 Kbyte
MB9AFB44NBBGL-GE1
Main: 256 Kbyte Work: 32 Kbyte
32 Kbyte
Document Number: 002-05631 Rev *B
Package
Packing
Plastic  LQFP 64-pin
(0.5mm pitch),
(LQD064)
Plastic  LQFP 64-pin
(0.65mm pitch),
(LQG064)
Plastic  QFN 64-pin
(0.5mm pitch),
(VNC064)
Plastic  LQFP 80-pin
(0.5mm pitch),
(LQH080)
Tray
Plastic  LQFP 80-pin
(0.65mm pitch),
(LQJ080)
Plastic  PFBGA
96-pin
(0.5mm pitch),
(FDG096)
Plastic  LQFP
100-pin
(0.5mm pitch),
(LQI100)
Plastic  QFP 100-pin
(0.65mm pitch),
(PQH100)
Plastic  PFBGA
112-pin
(0.8mm pitch),
(LBC112)
Tray
Page 111 of 128
MB9AB40NB Series
14.
Package Dimensions
Package Type
Package Code
LQFP 100
LQI100
D
D1
75
4
D
5 7
51
D1
51
50
76
4
5 7
75
50
76
E1 E
5 4
7
E1 E
5 4
7
3
6
26
100
1
26
25
1
25
2 5 7
e
100
BOTTOM VIEW
0.1 0 C A-B D
3
0.2 0 C A-B D
b
TOP VIEW
8
0.0 8
C A-B
D
2
A
9
A
SEAT ING
PLA NE
A'
0.25
L1
0.0 8 C
c
A1
b
10
SECTION A-A'
L
SIDE VIEW
SYMBOL
DETAIL A
DIMENSIONS
MIN.
NOM. MAX.
1.70
A
A1
0.05
b
0.15
0.15
0.27
c
0.09
0.20
D
16.00 BSC
D1
14.00 BSC
e
0.50 BSC
E
16.00 BSC
E1
14.00 BSC
L
0.45
0.60
0.75
L1
0.30
0.50
0.70
NOTES :
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. DATUM PLANE H IS LOCATED AT THE BOTTOM OF THE MOLD PARTING
LINE COINCIDENT WITH WHERE THE LEAD EXITS THE BODY.
3. DATUMS A-B AND D TO BE DETERMINED AT DATUM PLANE H.
4. TO BE DETERMINED AT SEATING PLANE C.
5. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS 0.25mm PRE SIDE.
DIMENSIONS D1 AND E1 INCLUDE MOLD MISMATCH AND ARE DETERMINED
AT DATUM PLANE H.
6. DETAILS OF PIN 1 IDENTIFIER ARE OPTIONAL BUT MUST BE LOCATED
WITHIN THE ZONE INDICATED.
7. REGARDLESS OF THE RELATIVE SIZE OF THE UPPER AND LOWER BODY
SECTIONS. DIMENSIONS D1 AND E1 ARE DETERMINED AT THE LARGEST
FEATURE OF THE BODY EXCLUSIVE OF MOLD FLASH AND GATE BURRS.
BUT INCLUDING ANY MISMATCH BETWEEN THE UPPER AND LOWER
SECTIONS OF THE MOLDER BODY.
8. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. THE DAMBAR
PROTRUSION (S) SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED b
MAXIMUM BY MORE THAN 0.08mm. DAMBAR CANNOT BE LOCATED ON
THE LOWER RADIUS OR THE LEAD FOOT.
9. THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10mm AND 0.25mm FROM THE LEAD TIP.
10. A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE TO
THE LOWEST POINT OF THE PACKAGE BODY.
002-11500 *A
PACKAGE OUTLINE, 100 LEAD LQFP
14.0X14.0X1.7 MM LQI100 REV*A
Document Number: 002-05631 Rev *B
Page 112 of 128
MB9AB40NB Series
Package Type
Package Code
QFP 100
PQH100
D
D1
4
5 7
80
51
81
51
50
80
50
81
31
100
E1 E
5
7
6
3
4
31
100
1
30
e
3
0.40 C A-B D
30
2 5 7
1
0.20 C A-B D
b
0.13
C A-B
D
BOTTOM VIEW
8
TOP VIEW
2
9
A
A'
SEATING
PLANE
L2
c
10
b
0.10 C
SECTION A-A'
DETAIL A
SIDE VIEW
SYMBOL
DIMENSIONS
MIN.
NOM. MAX.
A1
0.05
0.45
b
0.27
c
0.11
A
3.35
0.32
0.23
D
23.90 BSC
D1
20.00 BSC
e
0.65 BSC
E
17.90 BSC
E1
14.00 BSC
0
L
0.37
8
0.73
0.88
L1
1.95 REF
L2
0.25 BSC
1.03
002-15156 **
PACKAGE OUTLINE, 100 LEAD QFP
20.00X14.00X3.35 MM PQH100 REV**
Document Number: 002-05631 Rev *B
Page 113 of 128
MB9AB40NB Series
Package Type
Package Code
LQFP 80
LQH080
D
D1
60
4
5 7
41
41
40
61
60
40
61
21
80
5
7
E1
E
4
3
6
80
21
1
20
D
e
20
2 5 7
0.10 C A-B D
3
b
0.08
C A-B
1
BOTTOM VIEW
D
0.20 C A-B D
8
TOP VIEW
2
A
A
A'
0.08 C
SIDE VIEW
SEATING
PLANE
9
L1
L
0.25
A1
10
c
b
SECTION A-A'
DIMENSIONS
SYMBOL
MIN. NOM. MAX.
A
A1
1. 70
0.05
0.15
b
0.15
0.27
c
0.09
0.20
D
14.00 BSC.
D1
12.00 BSC.
e
0.50 BSC
E
14.00 BSC.
E1
12.00 BSC.
L
0.45
0.60
0.75
L1
0.30
0.50
0.70
002-11501 **
PACKAGE OUTLINE, 80 LEAD LQFP
12.0X12.0X1.7 MM LQH080 Rev **
Document Number: 002-05631 Rev *B
Page 114 of 128
MB9AB40NB Series
Package Type
Package Code
LQFP 80
LQJ080
D
D1
60
4
5 7
41
41
61
40
E1
60
40
61
21
80
E
5
7
4
3
6
80
21
1
20
20
2 5 7
1
0.10 C A-B D
3
e
0.20 C A-B D
b
ddd
C A-B
D
8
2
A
9
A
A'
0.10 C
SEATING
PLANE
c
L1
0.2 5
A1
10
b
SECTION A-A'
L
SYMBOL
DIMENSIONS
MIN. NOM. MAX.
1.70
A
A1
0.00
b
0.16
c
0.09
0.20
0.32
0.38
0.20
D
16.00 BSC
D1
14.00 BSC
e
0.65 BSC
E
16.00 BSC
14.00 BSC
E1
L
0.45
0.60
0.75
L1
0.30
0.50
0.70
0
8
002-14043 **
PACKAGE OUTLINE, 80 LEAD LQFP
14.0X14.0X1.7 MM LQJ080 REV**
Document Number: 002-05631 Rev *B
Page 115 of 128
MB9AB40NB Series
Package Type
Package Code
LQFP 64
LQD064
4
D
D1
48
5 7
33
33
32
49
48
32
49
17
64
5
7
E1
E
4
3
6
17
64
1
16
e
1
16
2 5 7
3
BOTTOM VIEW
0.10 C A-B D
0.20 C A-B D
b
0.08
C A-B
D
8
TOP VIEW
A
2
9
A
A'
0.08 C
SEATING
PLANE
L1
0.25
L
A1
c
b
SECTION A-A'
10
SIDE VIEW
SYMBOL
DIMENSIONS
MIN. NOM. MAX.
A
A1
1. 70
0.00
0.20
b
0.15
0.2
c
0.09
0.20
D
12.00 BSC.
D1
10.00 BSC.
e
0.50 BSC
E
12.00 BSC.
E1
10.00 BSC.
L
0.45
0.60
0.75
L1
0.30
0.50
0.70
002-11499 **
PACKAGE OUTLINE, 64 LEAD LQFP
10.0X10.0X1.7 MM LQD064 Rev**
Document Number: 002-05631 Rev *B
Page 116 of 128
MB9AB40NB Series
Package Type
Package Code
LQFP 64
LQG064
D
D1
48
4
5 7
33
33
32
49
48
32
49
17
64
E1 E
5
7
4
3
17
64
1
16
e
1
16
2 5 7
3
BOTTOM VIEW
0.10 C A-B D
0.20 C A-B D
b
0.13
C A-B
D
8
TOP VIEW
2
A
A
A'
0.10 C
SEATI NG
PLA NE
0.2 5
L1
L
9
A1
10
c
b
SEC TION A -A'
SIDE VIEW
SYMBOL
DIMENSION
MIN.
NOM. MAX.
0.00
0.20
1.70
A
A1
b
0.27
c
0.09
0.32
0.37
0.20
D
14.00 BSC
D1
12.00 BSC
e
0.65 BSC
E
14.00 BSC
E1
12.00 BSC
L
0.45
0.60
0.75
L1
0.30
0.50
0.70
0
002-13881 **
PACKAGE OUTLINE, 64 LEAD LQFP
12.0X12.0X1.7 MM LQG064 REV**
Document Number: 002-05631 Rev *B
Page 117 of 128
MB9AB40NB Series
Package Type
Package Code
QFN 64
VNC064
0.10
D
A
48
0.10 C
2X
33
33
32
49
C A B
D2
48
32
49
0.10
C A B
5
(ND-1)
E
e
17
64
1
INDEXMARK
8
E2
16
9
B
e
L
0.10 C
TOP VIEW
64
17
16
BOTTOM VIEW
2X
b
1
4
0.10
0.05
C A B
C
0.10 C
A
0.05 C
SEATINGPLANE
C
A1
SIDE VIEW
DIMENSIONS
NOTES:
SYMBOL
MIN. NOM. MAX.
A
A1
0.90
0.00
0.05
D
9.00 BSC
E
9.00 BSC
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. DIMENSIONING AND TOLERANCING CONFORMS TO ASME Y14.5M-1994.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4
b
0.20 0.25 0.30
D2
6.00 BSC
E2
6.00 BSC
6.
7.
e
0.50 BSC
8
R
0.20 REF
L
0.35
0.40 0.45
N
64
ND
16
5
9
DIMENSION "b" APPLIES TO METALLIZED TERMINAL AND IS MEASURED
BETWEEN 0.15 AND 0.30mm FROM TERMINAL TIP. IF THE TERMINAL
HAS THE OPTIONAL RADIUS ON THE OTHER END OF THE TERMINAL,
THE DIMENSION "b" SHOULD NOT BE MEASURED IN THAT RADIUS AREA.
ND REFERS TO THE NUMBER OF TERMINALS ON D SIDE OR E SIDE.
MAX. PACKAGE WARPAGE IS 0.05mm.
MAXIMUM ALLOWABLE BURR IS 0.076mm IN ALL DIRECTIONS.
PIN #1 ID ON TOP WILL BE LOCATED WITHIN THE INDICATED ZONE.
BILATERAL COPLANARITY ZONE APPLIES TO THE EXPOSED HEAT
SINK SLUG AS WELL AS THE TERMINALS.
002-13234 **
PACKAGE OUTLINE, 64 LEAD QFN
9.0X9.0X0.9 MM VNC064 6.0X6.0 MM EPAD (SAWN) Rev*.*
Document Number: 002-05631 Rev *B
Page 118 of 128
MB9AB40NB Series
Package Type
Package Code
FBGA 112
LBC112
A
0.20 C
11
2X
10
9
6
8
7
6
5
4
3
2
1
L
PIN A1
CORNER
INDEX MARK
K
J
H
G
F
E
D
C
B
A
6
B
7
0.20 C
TOP VIEW
2X
BOTTOM VIEW
DETAIL A
5
112x φb
C
0.10 C
DETAIL A
0.08
C A B
SIDE VIEW
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSIONS
SYMBOL
2. SOLDER BALL POSITION DESIGNATIO
N PER JEP95, SECTION 3, SPP-020.
MIN.
NOM.
MAX.
A
-
-
1.45
3. "e" REPRESENTS THE SOLDER BALL GRID PITCH.
A1
0.25
0.35
0.45
4. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE "D" DIRECTION.
D
10.00 BSC
SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE "E" DIRECTION.
E
10.00 BSC
N IS THE NUMBER OF POPULATED SOLDER BALL POSITIONS FOR MATRIX
D1
8.00 BSC
E1
8.00 BSC
MD
5. DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A
PLANE PARALLEL TO DATUM C.
11
ME
11
N
112
b
SIZE MD X ME.
0.35
0.45
eD
0.80 BSC
eE
0.80 BSC
SD
0.00
SE
0.00
6. "SD" AND "SE" ARE MEASUREDWITH RESPECT TO DATUMS A AND B AND
DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW.
0.55
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW,
"SD" OR "SE" = 0.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW,
"SD" = eD/2 AND "SE" = eE/2.
7. A1 CORNER TO BE IDENTIFIED BY
CHAMFER, LASER OR INK MARK
METALIZED MARK, INDENTATION OR OTHER MEANS.
8. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED SOLDER
BALLS.
002-13225 **
PACKAGE OUTLINE, 112 BALL FBGA
10.00X10.00X1.45 MM LBC112 REV**
Document Number: 002-05631 Rev *B
Page 119 of 128
MB9AB40NB Series
Package Type
Package Code
FBGA 96
FDG096
A
0.20 C
11
2X
10
9
6
8
7
6
5
4
3
2
1
L
PIN A1
CORNER
INDEX MARK
K
J
H
G
F
E
D
0.20 C
TOP VIEW
C
B
A
6
B
7
2X
BOTTOM VIEW
DETAIL A
0.20 C
0.08 C
C
96xφb
DETAIL A
5
0.05
SIDE VIEW
C A B
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSIONS
SYMBOL
MIN.
NOM.
MAX.
2. SOLDER BALL POSITION DESIGNATIO
N PER JEP95, SECTION 3, SPP-020.
A
-
-
1.30
3. "e" REPRESENTSTHE SOLDER BALL GRID PITCH.
A1
0.15
0.25
0.35
4. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE "D" DIRECTION.
D
6.00 BSC
SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE "E" DIRECTION.
E
6.00 BSC
N IS THE NUMBER OF POPULATED SOLDER BALL POSITIONS FOR MATRIX
D1
5.00 BSC
E1
5.00 BSC
MD
PLANE PARALLEL TO DATUM C.
11
ME
11
N
96
b
SIZE MD X ME.
5. DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A
0.20
0.30
eD
0.50 BSC
eE
0.50 BSC
SD
0.00
SE
0.00
6. "SD" AND "SE" ARE MEASURED WITH RESPECT TO DATUMS A AND B AND
DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW.
0.40
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW,
"SD" OR "SE" = 0.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW,
"SD" = eD/2 AND "SE" = eE/2.
7. A1 CORNER TO BE IDENTIFIED BY
CHAMFER, LASER OR INK MARK
METALIZED MARK, INDENTATION OR OTHER MEANS.
8. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED SOLDER
BALLS.
002-13224 **
PACKAGE OUTLINE, 96 BALL FBGA
6.0X6.0X1.3 MM FDG096 REV**
Document Number: 002-05631 Rev *B
Page 120 of 128
MB9AB40NB Series
15.
Errata
This chapter describes the errata for MB9AB40N, MB9AB40NA and MB9AB40NB series. Details include errata trigger
conditions, scope of impact, available workaround, and silicon revision applicability.
Contact your local Cypress Sales Representative if you have questions.
15.1
Part Numbers Affected
Part Number
Initial Revision
MB9AFB41NPMC-G-JNE2, MB9AFB42NPMC-G-JNE2, MB9AFB44NPMC-G-JNE2,
MB9AFB41NPQC-G-JNE2, MB9AFB42NPQC-G-JNE2, MB9AFB44NPQC-G-JNE2,
MB9AFB41NBGL-GE1, MB9AFB42NBGL-GE1, MB9AFB44NBGL-GE1,
MB9AFB41MPMC-G-JNE2, MB9AFB42MPMC-G-JNE2, MB9AFB44MPMC-G-JNE2,
MB9AFB41MPMC1-G-JNE2, MB9AFB42MPMC1-G-JNE2, MB9AFB44MPMC1-G-JNE2,
MB9AFB41MBGL-GE1, MB9AFB42MBGL-GE1, MB9AFB44MBGL-GE1,
MB9AFB41LPMC1-G-JNE2, MB9AFB42LPMC1-G-JNE2, MB9AFB44LPMC1-G-JNE2,
MB9AFB41LPMC-G-JNE2, MB9AFB42LPMC-G-JNE2, MB9AFB44LPMC-G-JNE2,
MB9AFB41LQN-G-AVE2, MB9AFB42LQN-G-AVE2, MB9AFB44LQN-G-AVE2
Rev. A
MB9AFB41NAPMC-G-JNE2, MB9AFB42NAPMC-G-JNE2, MB9AFB44NAPMC-G-JNE2,
MB9AFB41NAPQC-G-JNE2, MB9AFB42NAPQC-G-JNE2, MB9AFB44NAPQC-G-JNE2,
MB9AFB41NABGL-GE1, MB9AFB42NABGL-GE1, MB9AFB44NABGL-GE1,
MB9AFB41MAPMC-G-JNE2, MB9AFB42MAPMC-G-JNE2, MB9AFB44MAPMC-G-JNE2,
MB9AFB41MAPMC1-G-JNE2, MB9AFB42MAPMC1-G-JNE2, MB9AFB44MAPMC1-G-JNE2,
MB9AFB41MABGL-GE1, MB9AFB42MABGL-GE1, MB9AFB44MABGL-GE1,
MB9AFB41LAPMC1-G-JNE2, MB9AFB42LAPMC1-G-JNE2, MB9AFB44LAPMC1-G-JNE2,
MB9AFB41LAPMC-G-JNE2, MB9AFB42LAPMC-G-JNE2, MB9AFB44LAPMC-G-JNE2,
MB9AFB41LAQN-G-AVE2, MB9AFB42LAQN-G-AVE2, MB9AFB44LAQN-G-AVE2
Rev. B
MB9AFB41NBPMC-G-JNE2, MB9AFB42NBPMC-G-JNE2, MB9AFB44NBPMC-G-JNE2,
MB9AFB41NBPQC-G-JNE2, MB9AFB42NBPQC-G-JNE2, MB9AFB44NBPQC-G-JNE2,
MB9AFB41NBBGL-GE1, MB9AFB42NBBGL-GE1, MB9AFB44NBBGL-GE1,
MB9AFB41MBPMC-G-JNE2, MB9AFB42MBPMC-G-JNE2, MB9AFB44MBPMC-G-JNE2,
MB9AFB41MBPMC1-G-JNE2, MB9AFB42MBPMC1-G-JNE2, MB9AFB44MBPMC1-G-JNE2,
MB9AFB41MBBGL-GE1, MB9AFB42MBBGL-GE1, MB9AFB44MBBGL-GE1,
MB9AFB41LBPMC1-G-JNE2, MB9AFB42LBPMC1-G-JNE2, MB9AFB44LBPMC1-G-JNE2,
MB9AFB41LBPMC-G-JNE2, MB9AFB42LBPMC-G-JNE2, MB9AFB44LBPMC-G-JNE2,
MB9AFB41LBQN-G-AVE2, MB9AFB42LBQN-G-AVE2, MB9AFB44LBQN-G-AVE2,
15.2
Qualification Status
Product Status: In Production − Qual.
15.3
Errata Summary
This table defines the errata applicability to available devices.
Document Number: 002-05631 Rev *B
Page 121 of 128
MB9AB40NB Series
Items
Part Number
Silicon Revision
Fix Status
[1] FLASH lower bank read during write
Refer to 15.1
Initial rev.
Fixed in Rev. A
[2] FLASH read during write & erase suspend
Refer to 15.1
Initial rev.
Fixed in Rev. A
[3] Regulator issue
Refer to 15.1
Initial rev., Rev. A
Fixed in Rev. B
[4] HDMI-CEC arbitration lost issue
Refer to 15.1
Initial rev., Rev. A
Fixed in Rev. B
[5] HDMI-CEC polling message issue
Refer to 15.1
Initial rev., Rev. A , Rev. B
Next silicon is not planned
1. FLASH lower bank read during write
 PROBLEM DEFINITION
During writing (programming) to FLASH memory of an upper bank, FLASH memory of a lower bank could not be read at a
specific timing in some operation combinations.
 PARAMETERS AFFECTED
N/A
 TRIGGER CONDITION(S)
This issue may happen when read data or fetch instruction from the FLASH memory lower bank (smaller sector), while a write
(program) operation to the FLASH memory upper bank (larger sector) is in progress.
 SCOPE OF IMPACT
Instructions could not be fetched (read) correctly from the lower bank, and then execution of the (corrupted) instructions may
cause a hard fault or run-away. If an instruction in RAM reads a data from the lower bank while writing to the upper bank, an
incorrect value might be read.
 WORKAROUND
To rewrite the upper bank of FLASH memory, put the write instruction in RAM instead of the lower bank and execute it from
the RAM. Do not access the lower bank until the write operation is completed (RDY=1). Especially to avoid a vector fetch
from the lower bank of the FLASH memory by an interrupt occurred, the interrupt should be prohibited or the vector address
should be set to RAM by the vector table offset register.
 FIX STATUS
This issue was fixed in Rev. A.
2. FLASH Read during Write & Sector Erase Suspend
 PROBLEM DEFINITION
When writing is executed during sector erase suspend, FLASH memory could not be read correctly at a specific timing.
 PARAMETERS AFFECTED
N/A
 TRIGGER CONDITION(S)
This issue may happen when read data or fetch instruction from the FLASH memory bank (higher or lower), while a write
(program) operation is in progress to the opposite bank which has a sector erase suspended. The following flow could not be
executed correctly.
(a) Erase a sector of a bank
(b) Suspend the sector erase operation
(c) Write to a different sector of the bank
(d) Execute an instruction or read data in the opposite bank
Document Number: 002-05631 Rev *B
Page 122 of 128
MB9AB40NB Series
 SCOPE OF IMPACT
 Instructions could not be fetched (read) correctly, and then execution of the (corrupted) instructions may cause a hard fault or
run-away. If an instruction in RAM reads a data from the bank, an incorrect value might be read.
 WORKAROUND
Do not execute the write operation to a different sector in the same bank at sector erase suspend.
 FIX STATUS
This issue was fixed in Rev. A.
3. Regulator issue
 PROBLEM DEFINITION
The regulator does not get initialized while internal power-up sequence.
 PARAMETERS AFFECTED
N/A
 TRIGGER CONDITION(S)
This issue rarely happens depending on states of internal circuits which the user cannot control.
 SCOPE OF IMPACT
MCU does not start operation if this issue occurs.
 WORKAROUND
This error cannot be avoided by any software.
 FIX STATUS
This issue was fixed in Rev. B.
4. HDMI-CEC arbitration lost issue
 PROBLEM DEFINITION
Large external load on CEC bus may cause arbitration lost.
 PARAMETERS AFFECTED
N/A
 TRIGGER CONDITION(S)
The arbitration lost detection mechanism samples outputting signals and determines that arbitration lost occurs if sampled
signals do not match the outputting signals. The large external load on the CEC bus increases slew rate of the signals. The
increased slew rate makes the mismatch between outputting signals and sampled signals and the mismatch misleads MCU
that arbitration lost occurs.
 SCOPE OF IMPACT
Once the arbitration lost is detected, the CEC aborts the transmission. Any transmission cannot be completed.
 WORKAROUND
 This error cannot be avoided by any software. Reduce the external load.
 FIX STATUS
 This issue was fixed in Rev. B.
Document Number: 002-05631 Rev *B
Page 123 of 128
MB9AB40NB Series
5. HDMI-CEC polling message issue
 PROBLEM DEFINITION
Error#1) While MCU sends a Polling Message, it always returns a NACK to a message coming to the MCU from another
node.
Error#2) MCU always waits for 7-bit signal free on CEC line before it drives the line even when the last line initiator was
another node.
 PARAMETERS AFFECTED
N/A
 TRIGGER CONDITION(S)
This error always happens.
 SCOPE OF IMPACT
MCU does not reply properly to another node.
 WORKAROUND
The software workaround is applied to Error #1.
1.
Store 0x0 to SFREE register.
2.
Monitor CEC line with GPIO and wait until 1 lasts for the signal free time.
3.
Store frame data to TXDATA register and store 0x0F to RCADR1 or RCADR2 register.
It sends a message after 3~4 clocks of 32.768 kHz clock when TXDATA is stored 0x0F.
If the device receives a frame from another node within 2~3 clocks after storing TXDATA, the bus error occurs and if the
device receives a frame from another node within 3~4 clocks after storing TXDATA, the arbitration lost occurs. In these cases:
4-A-1. Set RCADR1 or RCADR2 to former value from 0x0F to reply ACK
4-A-2. Return back to step 2 above
If the device receives a frame from another node within 1~2 clocks after storing TXDATA, take these steps.
4-B-1. Monitor CEC line with GPIO after 50us from storing TXDATA
4-B-2. Set TXEN to 1 -> 0 -> 1 immediately when GPIO finds state low on the CEC line
4-B-3. Set RCADR1 or RCADR2 to former value from 0x0F to reply ACK
4-B-4. Return back to step 2 above
For Error #2, there is no software workaround, but signal free time of fixed 7-bit does not violate HDMI-CEC specification. The
specification says signal free time must be more than and equals to 5-bit.
 FIX STATUS
The user uses the workaround to avoid the issue. The next silicon fixing the issue is not planned.
Document Number: 002-05631 Rev *B
Page 124 of 128
MB9AB40NB Series
16.
Major Changes
Spansion Publication Number: DS706-00034
Page
Section
Change Results
Revision 2.0
2
6
7
52
57
62
70
74
78, 79
80
85, 87,
89, 91
94
97
FEATURE
 On-chip Memories
 USB Interface
 Unique ID
PRODUCT LINEUP
 Function
HANDLING DEVICES
MEMORY MAP
 Memory Map (2)
PIN STATUS IN EACH CPU STATE
 List of Pin Status
ELECTRICAL CHARACTERISTICS
3.DC Characteristics
(1) Current rating
5.AC Characteristics
(3) Built-in CR Oscillation Characteristics
 Built-in high-speed CR
(7) External Bus Timing
 Separate Bus Access Asynchronous
SRAM Mode
 Separate Bus Access Synchronous SRAM
Mode
(9) CSIO Timing
(11) I2C Timing
6. 12-bit A/D Converter
 Electrical Characteristics for the A/D
Converter
99
 Definition of 12-bit A/D Converter Terms
104
8. Low-Voltage Detection Characteristics
(1) Low-Voltage Detection Reset
(2) Interrupt of Low-Voltage Detection
105
Revision 2.1
Revision 3.0
-
-
-
-
2
3
7
55
56
68
 FEATURES
•External Bus Interface
•Multi-function Serial Interface
PRODUCT LINEUP
•Function
BLOCK DIAGRAM
MEMORY MAP
•Memory Map (1)
 ELECTRICAL CHARACTERISTICS
2.Recommended Operating Conditions
Revised the descriptions of [Flash memory].
Revised the descriptions of [USB function].
Added the descriptions of "Unique ID".
Added the descriptions.
Revised the Pin status type of "I".
 Revised the descriptions of Power supply current.
 Added the "Flash memory write/erase current".
 Added the footnote.
Revised the table and the footnote.
Revised the table and the figure.
 Revised the title to "CSIO Timing".
 Revised the note.
Revised the footnote.
• Revised the parameter.
• Revised the symbol.
• Corrected the value.
• Revised the parameter.
• Revised the symbol.
• Corrected "Conditions" and "Value" in the table.
• Added the Item.
• Added the footnote.
Added the Item.
Company name and layout design change
Corrected the Series name.
MB9AB40NA Series → MB9AB40NB Series
Corrected the Product name as follows.
MB9AFB44LB, MB9AFB42LB, MB9AFB41LB
MB9AFB44MB, MB9AFB42MB, MB9AFB41MB
MB9AFB44NB, MB9AFB42NB, MB9AFB41NB
Added the Item.
• Maximum area size : Up to 256 Mbytes
Corrected the description of "I2C"
Added the footnote
Corrected the figure
Corrected the address "External Device Area"
Add the footnote
69,70
3.DC Characteristics
(1) Current rating
•Corrected the Condition
•Delete the minmun value
•Corrected the remarks
•Add the footnote
92
(9) CSIO Timing
•Synchronous serial (SPI=1, SCINV=1)
Corrected the figure of "MS bit=1"
Document Number: 002-05631 Rev *B
Page 125 of 128
MB9AB40NB Series
Page
Section
(9) CSIO Timing
• External clock(EXT=1):asyntironous only
94
(12) I2C Timing
97
5.12-bit A/D Converter
•Electrical Characteristics for
the A/D Converter
ORDERING INFORMATON
107
Revision 4.0
Features
2
lUSB Interface
Memory Map
57
· Memory map(2)
Electrical Characteristics
3. DC Characteristics
69 - 71
(1) Current rating
Electrical Characteristics
3. DC Characteristics
72
(2) Pin Characteristics
Electrical Characteristics
5. AC Characteristics
(4-1) Operating Conditions of Main and USB
76
PLL
(4-2) Operating Conditions of Main PLL
Electrical Characteristics
5. AC Characteristics
77
(6) Power-on Reset Timing
Electrical Characteristics
5. AC Characteristics
86 - 93
(9) CSIO/UART Timing
98
Electrical Characteristics
6. 12bit A/D Converter
108 - 111
Electrical Characteristics
10. Return Time from Low-Power Consumption
Mode
Ordering Information
112, 113
Change Results
Corrected the figure
Corrected the description as follows.
•Typical mode → Standard-mode
•High-speed mode→ Fast-mode
•Corrected the terminal name
AN00 ~ AN23 → ANxx
•Corrected the minmum value of "Sampling time"
•Corrected the max and min value of "State transition time to
oprerationpermission"
•Corrected the footnote
Corrected the "Part number"
Added the description of PLL for USB
Added the summary of Flash memory sector and the note
· Changed the table format
· Added Main Timer mode current
· Moved A/D Converter Current
Added input leak current of CEC pin at power off.
Added the figure of Main PLL connection and USB PLL connection
· Added Time until releasing Power-on reset
· Changed the figure of timing
· Modified from UART Timing to CSIO/UART Timing
· Changed from Internal shift clock operation to Master mode
· Changed from External shift clock operation to Slave mode
· Added the typical value of Integral Nonlinearity, Differential
Nonlinearity, Zero transition voltage and Full-scale transition voltage
· Added Conversion time at AVcc < 2.7V
Added Return Time from Low-Power Consumption Mode
Changed notation of part number
NOTE: Please see “Document History” about later revised information.
Document Number: 002-05631 Rev *B
Page 126 of 128
MB9AB40NB Series
Document History
Document Title: MB9AB40NB Series 32-bit ARM® Cortex®-M3 FM3 Microcontroller
Document Number: 002-05631
Revision
ECN
Orig. of
Change
Submission
Date
**
-
AKIH
06/10/2015
Migrated to Cypress and assigned document number 002-05631.
No change to document contents or format.
*A
5120116
AKIH
02/15/2016
Updated to Cypress template
Description of Change
Updated “12.5.6 Power-On Reset Timing”. Changed parameter from “Power Supply
rise time(Tr)[ms]” to “Power ramp rate(dV/dt)[mV/μs]” and added some comments
(Page 77)
*B
5534251
YSKA
Document Number: 002-05631 Rev *B
07/26/2017
Modified RTC description in “Features, Real-Time Clock(RTC)” as below
Changed starting count value from 01 to 00. Deleted “second , or day of the week”
in the Interrupt function (Page 3)
Added Notes for JTAG (Page 40), Changed “J-TAG” to” JTAG” in “3.2 List of Pin
Functions” (Page 28)
Updated Package code and dimensions as follows (Page 7-14, 111-120)
FPT-64P-M38 -> LQD064, FPT-64P-M39 -> LQG064,
LCC-64P-M24 -> VNC064, FPT-80P-M37 -> LQH080,
FPT-80P-M40 -> LQJ080, BGA-96P-M07 -> FDG096,
FPT-100P-M23 -> LQI100, FPT-100P-M36 -> PQH100
BGA-112P-M04 -> LBC112
Added “16. Errata” (Page 121)
Change the name from “USB Function” to “USB Device” (Page 1, 6, 37)
Add “Analog reference voltage(AVRL)” in “13.2 Recommended Operating
Conditions” and “12.6 12-bit A/D Converter”(Page 67, 98)
Corrected the following statement
Analog port input current  Analog port input leak current
in chapter 13.6. 12-bit A/D Converter (Page 98)
Added the Baud rate spec in “12.5.9 CSIO/UART Timing”(Page 86, 88, 90, 92)
Page 127 of 128
MB9AB40NB Series
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the
office closest to you, visit us at Cypress Locations.
Products
ARM® Cortex® Microcontrollers
Automotive
Clocks & Buffers
Interface
Internet of Things
Memory
PSoC® Solutions
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless/RF
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6
Cypress Developer Community
Forums | WICED IOT Forums | Projects | Video | Blogs |
Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
ARM and Cortex are the registered trademarks of ARM Limited in the EU and other countries.
All other trademarks or registered trademarks referenced herein are the property of their respective owners.
© Cypress Semiconductor Corporation, 2012-2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document,
including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intell ectual property laws and treaties of the United States and other
countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights,
trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of
the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software
provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in
binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s
patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use,
reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes.
It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress
products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support
devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the
failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform
can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release
Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims,
costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-05631 Rev *B
July 26, 2017
Page 128 of 128
Similar pages