TI LM3480IM3X-15/NOPB Lm3480 100-ma, sot-23, quasi low-dropout linear voltage regulator Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
LM3480 100-mA, SOT-23, Quasi Low-Dropout Linear Voltage Regulator
1 Features
3 Description
•
•
•
•
•
The LM3480 is an integrated linear voltage regulator.
It features operation from an input as high as 30 V
and an ensured maximum dropout of 1.2 V at the full
100-mA load. Standard packaging for the LM3480 is
the 3-lead SOT-23 package.
1
•
•
•
Input Voltage Range: up to 30 V
3.3-V, 5-V, 12-V, and 15-V Versions Available
Packaged in the Tiny 3-Lead SOT-23 Package
30-V Maximum Input for Operation
1.2-V Ensured Maximum Dropout Over Full Load
and Temperature Ranges
100-mA Ensured Minimum Load Current
±5% Ensured Output Voltage Tolerance Over Full
Load and Temperature Ranges
−40 to +125°C Junction Temperature Range for
Operation
The 5-V, 12-V, and 15-V members of the LM3480
series are intended as tiny alternatives to industry
standard LM78Lxx series and similar devices. The
1.2-V quasi-low dropout of LM3480 series devices
makes them a nice fit in many applications where the
2-V to 2.5-V dropout of LM78Lxx series devices
precludes their (LM78Lxx series devices) use.
The LM3480 series also features a 3.3-V member.
The SOT-23 packaging and quasi-low dropout
features of the LM3480 series converge in this device
to provide a very nice, very tiny, 3.3-V, 100-mA bias
supply that regulates directly off the system 5-V ±5%
power supply.
2 Applications
•
•
•
•
Tiny Alternative to LM78Lxx Series and Similar
Devices
Tiny 5-V ±5% to 3.3-V, 100-mA Converter
Post Regulator for Switching DC/DC Converter
Bias Supply for Analog Circuits
Device Information(1)
PART NUMBER
LM3480
PACKAGE
SOT-23 (3)
BODY SIZE (NOM)
2.92 mm × 1.30 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
space
space
space
Typical Application Circuit
6.5 V IN
5 V, 100 mA OUT
2
1
LM3480IM3-5.0
CIN
0.1 µF
3
COUT
0.1 µF
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
7
1
1
1
2
3
4
Absolute Maximum Ratings ...................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 4
Electrical Characteristics: LM3480-3.3, LM3480-5 ... 5
Electrical Characteristics: LM3480-12, LM3480-15 .. 6
Typical Characteristics .............................................. 7
Detailed Description ............................................ 10
7.1 Overview ................................................................. 10
7.2 Functional Block Diagram ....................................... 10
7.3 Feature Description................................................. 10
7.4 Device Functional Modes........................................ 10
8
Application and Implementation ........................ 11
8.1 Application Information............................................ 11
8.2 Typical Application ................................................. 11
9 Power Supply Recommendations...................... 13
10 Layout................................................................... 13
10.1 Layout Guidelines ................................................. 13
10.2 Layout Example .................................................... 13
11 Device and Documentation Support ................. 14
11.1
11.2
11.3
11.4
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
14
14
14
14
12 Mechanical, Packaging, and Orderable
Information ........................................................... 14
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision G (February 2015) to Revision H
Page
•
Replaced Functional Block Diagram .................................................................................................................................... 10
•
Changed text of External Capacitors subsection ................................................................................................................ 11
•
Changed text of Output Capacitor subsection ..................................................................................................................... 11
Changes from Revision F (December 2014) to Revision G
Page
•
Changed pin numbers indicated in Typical Application drawing; fix typos............................................................................. 1
•
Deleted soldering specs - found in POA ................................................................................................................................ 4
•
Changed Handling Ratings to ESD Ratings format ............................................................................................................... 4
Changes from Revision E (March 2013) to Revision F
•
Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section; add updated Thermal Information ............................................................................................................................. 1
Changes from Revision D (March 2013) to Revision E
•
2
Page
Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 9
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
LM3480
www.ti.com
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
5 Pin Configuration and Functions
DBZ Package
3-Pin SOT-23
Top View
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
OUT
1
O
Output voltage
IN
2
I
Input voltage supply
GND
3
—
Common ground
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
3
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings (1) (2)
Input voltage (IN to GND)
MIN
MAX
UNIT
–0.3
35
V
Power dissipation (3)
Internally
Limited
Junction temperature (3)
–40
150
°C
Storage temperature, Tstg
−65
150
°C
(1)
(2)
(3)
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are
conditions under which operation of the device is ensured. Recommended operating ratings do not imply ensured performance limits.
For ensured performance limits and associated test conditions, see the Electrical Characteristics: LM3480-3.3, LM3480-5.
If Military- or Aerospace-specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
The Absolute Maximum power dissipation depends on the ambient temperature and can be calculated using P = (TJ – TA) / RθJA where
TJ is the junction temperature, TA is the ambient temperature, and RθJA is the junction-to-ambient thermal resistance. The 370-mW
rating results from substituting the Absolute Maximum junction temperature, 150°C for TJ, 50°C for TA, and 269.6°C/W for RθJA. More
power can be safely dissipated at lower ambient temperatures. Less power can be safely dissipated at higher ambient temperatures.
The Absolute Maximum power dissipation can be increased by 3.7 mW for each °C below 50°C ambient. It must be derated by 3.7 mW
for each °C above 50°C ambient. Heat sinking enables the safe dissipation of more power. The LM3480 actively limits its junction
temperature to about 150°C.
6.2 ESD Ratings
VALUE
Electrostatic
discharge
V(ESD)
(1)
(2)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) (1)
MIN
Maximum input voltage (IN to GND)
Junction temperature (TJ)
(1)
MAX
UNIT
0
30
V
–40
125
°C
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are
conditions under which operation of the device is ensured. Recommended operating ratings do not imply ensured performance limits.
For ensured performance limits and associated test conditions, see the Electrical Characteristics: LM3480-3.3, LM3480-5.
6.4 Thermal Information
LM3480
THERMAL METRIC (1)
SOT-23 (DBZ)
UNIT
3 PINS
RθJA
Junction-to-ambient thermal resistance
269.6
RθJC(top)
Junction-to-case (top) thermal resistance
141.1
RθJB
Junction-to-board thermal resistance
63.1
ψJT
Junction-to-top characterization parameter
24.2
ψJB
Junction-to-board characterization parameter
62.1
(1)
4
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
LM3480
www.ti.com
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
6.5 Electrical Characteristics: LM3480-3.3, LM3480-5
Typical and other limits apply for TA = TJ = 25°C, unless otherwise specified. Nominal output voltage (VNOM) = 3.3 V or 5
V. (1) (2) (3)
PARAMETER
VOUT
Output voltage
TEST CONDITIONS
VNOM = 3.3 V
TYP
MAX
MIN
TYP
MAX
VIN = VNOM + 1.5 V
1 mA ≤ IOUT ≤ 100 mA
3.17
3.3
3.43
4.8
5
5.2
VIN = VNOM + 1.5 V
1 mA ≤ IOUT ≤ 100 mA
−40°C ≤ TJ ≤ 125°C
3.14
3.46
4.75
Line regulation
Load regulation
Ground pin current
VIN VOUT
Dropoutvoltage
20
(1)
(2)
(3)
Output noise voltage
2
40
2
mA
4
0.7
0.9
4
0.7
1
0.9
VIN = 10 V
Bandwidth: 10 Hz to 100 kHz
20
mV
IOUT = 100 mA
−40°C ≤ TJ ≤ 125°C
en
25
40
IOUT = 10 mA
−40°C ≤ TJ ≤ 125°C
IOUT = 100 mA
12
mV
VNOM + 1.5 V ≤ VIN ≤ 30 V
No Load,
−40°C ≤ TJ ≤ 125°C
IOUT = 10 mA
5.25
25
VIN = VNOM + 1.5 V
10 mA ≤ IOUT ≤ 100 m
−40°C ≤ TJ ≤ 125°C
VNOM + 1.5 V ≤ VIN ≤ 30 V
No Load
IGND
10
VNOM + 1.5 V ≤ VIN ≤ 30 V
IOUT = 1 mA
−40°C ≤ TJ ≤ 125°C
VIN = VNOM + 1.5 V
10 mA ≤ IOUT ≤ 100 mA
ΔVOUT
UNIT
V
VNOM + 1.5 V ≤ VIN ≤ 30 V
IOUT = 1 mA
ΔVOUT
VNOM = 5 V
MIN
1.1
1
0.9
1.2
100
0.9
V
1.1
1.2
150
V
µVrms
A typical is the center of characterization data taken with TA = TJ = 25°C. Typicals are not ensured.
All limits are ensured. All electrical characteristics having room-temperature limits are tested during production with TA = TJ = 25°C. All
hot and cold limits are ensured by correlating the electrical characteristics to process and temperature variations and applying statistical
process control.
All voltages except dropout are with respect to the voltage at the GND pin.
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
5
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
www.ti.com
6.6 Electrical Characteristics: LM3480-12, LM3480-15
Typical and other limits apply for TA = TJ = 25°C, unless otherwise specified. Nominal output voltage (VNOM) = 12 V or 15
V. (1) (2) (3)
PARAMETER
VOUT
Output voltage
TEST CONDITIONS
VNOM = 12 V
TYP
MAX
MIN
TYP
MAX
VIN = VNOM + 1.5 V
1 mA ≤ IOUT ≤ 100 mA
11.52
12
12.48
14.4
15
15.6
VIN = VNOM + 1.5 V
1 mA ≤ IOUT ≤ 100 mA
−40°C ≤ TJ ≤ 125°C
11.4
12.6
14.25
Line regulation
IGND
Load regulation
Ground pin current
VNOM + 1.5 V ≤ VIN ≤ 30 V
No Load
Dropout voltage
36
(1)
(2)
(3)
6
Output noise voltage
45
mV
2
75
2
mA
4
0.7
IOUT = 10 mA,
−40°C ≤ TJ ≤ 125°C
0.9
4
0.7
1
0.9
VIN = 10 V
Bandwidth: 10 Hz to 100 kHz
40
60
IOUT = 100 mA ,
−40°C ≤ TJ ≤ 125°C
en
16
mV
VNOM + 1.5 V ≤ VIN ≤ 30 V
No Load, −40°C ≤ TJ ≤ 125°C
IOUT = 100 mA
15.75
40
VIN = VNOM + 1.5 V
10 mA ≤ IOUT ≤ 100 mA
−40°C ≤ TJ ≤ 125°C
IOUT = 10 mA
VIN VOUT
14
VNOM + 1.5 V ≤ VIN ≤ 30 V
IOUT = 1 mA
−40°C ≤ TJ ≤ 125°C
VIN = VNOM + 1.5 V
10 mA ≤ IOUT ≤ 100 mA
ΔVOUT
UNIT
V
VNOM + 1.5 V ≤ VIN ≤ 30 V
IOUT = 1 mA
ΔVOUT
VNOM = 15 V
MIN
1.1
1
0.9
1.2
360
0.9
1.1
1.2
450
V
V
µVrms
A typical is the center of characterization data taken with TA = TJ = 25°C. Typicals are not ensured.
All limits are ensured. All electrical characteristics having room-temperature limits are tested during production with TA = TJ = 25°C. All
hot and cold limits are ensured by correlating the electrical characteristics to process and temperature variations and applying statistical
process control.
All voltages except dropout are with respect to the voltage at the GND pin.
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
LM3480
www.ti.com
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
6.7 Typical Characteristics
Unless indicated otherwise, VIN = VNOM + 1.5 V, CIN = 0.1 µF, COUT = 0.1 µF, and TA .= 25°C.
Figure 1. Dropout Voltage vs Load Current
Figure 2. Dropout Voltage vs Junction Temperature
Figure 3. Ground Pin Current vs Input Voltage
Figure 4. Ground Pin Current vs Input Voltage
Figure 5. Ground Pin Current vs Load Current
Figure 6. Ground Pin Current vs Junction Temperature
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
7
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
www.ti.com
Typical Characteristics (continued)
Unless indicated otherwise, VIN = VNOM + 1.5 V, CIN = 0.1 µF, COUT = 0.1 µF, and TA .= 25°C.
8
Figure 7. Input Current vs Input Voltage
Figure 8. Input Current vs Input Voltage
Figure 9. Output Voltage vs Input Voltage
Figure 10. Output Voltage vs Input Voltage
Figure 11. Output Voltage vs Input Voltage
Figure 12. Output Voltage vs Input Voltage
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
LM3480
www.ti.com
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
Typical Characteristics (continued)
Unless indicated otherwise, VIN = VNOM + 1.5 V, CIN = 0.1 µF, COUT = 0.1 µF, and TA .= 25°C.
Figure 13. Output Short-Circuit Current
Figure 14. Output Short-Circuit Current
Figure 15. Power Supply Rejection Ratio
Figure 16. Power Supply Rejection Ratio
Figure 17. DC Load Regulation
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
9
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LM3480 is an integrated linear voltage regulator with inputs that can be as high as 30 V. It ensures a
maximum dropout of 1.2 V at the full load of 100 mA. The LM3480 has different output options including 3.3-V, 5V, 12-V, and 15-V outputs, making LM3480 the tiny alternative to industry standard LM78Lxx series and similar
devices.
7.2 Functional Block Diagram
IN
OUT
Current
Limit
NPN
Thermal
Shutdown
PNP
+
Bandgap
Reference
LM3480
GND
7.3 Feature Description
7.3.1 3.3-V, 5-V, 12-V, and 15-V Versions Available
The 3.3-V, 5-V, 12-V, and 15-V versions of LM3480 series are intended as tiny alternatives to industry standard
LM78Lxx series and similar devices.
7.3.2 1.2-V Ensured Maximum Dropout
The 1.2-V quasi-low dropout of the LM3480 series devices make them a nice fit in many application where the 2V to 2.5-V dropout of LM78Lxx series devices precludes their use.
7.4 Device Functional Modes
7.4.1 Operation with VIN = 5 V
The 3.3-V member of LM3480 can operate with an input of 5 V ±5%, its tiny SOT-23 package and quasi-low
dropout makes it suitable for providing a very tiny, 3.3-V, 100-mA bias supply from 5-V power supply.
10
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
LM3480
www.ti.com
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM3480 is a linear voltage regulator with 1.2-V ensured maximum dropout and 100-mA ensured minimum
load current. This device has 3.3-V, 5-V, 12-V, and 15-V versions. The implementation of LM3480 is discussed in
this section.
8.2 Typical Application
6.5 V IN
5 V, 100 mA OUT
2
1
LM3480IM3-5.0
3
CIN
0.1 µF
COUT
0.1 µF
8.2.1 Design Requirements
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
6.5 V
Output voltage
5V
Output current
100 mA
8.2.2 Detailed Design Procedure
8.2.2.1 External Capacitors
A minimum input and output capacitance value of 0.1 µF is required for stability and adequate transient
performance. There is no specific ESR limitation, although excessively high ESR will compromise transient
performance. There is no specific limitation on a maximum capacitance value on the input or the output.
8.2.2.1.1 Output Capacitor
The minimum output capacitance required to maintain stability is 0.1 µF. Larger values of output capacitance can
be used to improve transient behavior.
8.2.3 Application Curves
Unless indicated otherwise, VIN = 6.5 V, VOUT = 5 V, COUT = 0.1 µF, and TA = 25°C
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
11
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
12
www.ti.com
Figure 18. Line Transient Response
Figure 19. Line Transient Response
Figure 20. Load Transient Response
Figure 21. Load Transient Response
Figure 22. Load Transient Response
Figure 23. Load Transient Response
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
LM3480
www.ti.com
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
9 Power Supply Recommendations
The LM3480 is designed to operated from up to a 30-V input voltage supply. This input supply must be well
regulated. If the input supply is noisy, additional input capacitors with low ESR can help to improve the output
noise performance.
10 Layout
10.1 Layout Guidelines
For best overall performance, place all the circuit components on the same side of the circuit board and as near
as practical to the respective LDO pin connections. Place ground return connections to the input and output
capacitors, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side,
copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and
negatively affects system performance. This grounding and layout scheme minimizes the inductive parasitic, and
thereby reduces load-current transients, minimizes noise, and increases circuit stability.
A ground reference plane is also recommended and is either embedded in the PCB itself or located on the
bottom side of the PCB opposite the components. This reference plane serves to assure accuracy of the output
voltage, shield noise, and behaves similar to a thermal plane to spread heat from the LDO device. In most
applications, this ground plane is necessary to meet thermal requirements.
10.2 Layout Example
VIN
2
1
IN
OUT
VOUT
GND
3
GND
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
13
LM3480
SNVS011H – JUNE 1999 – REVISED SEPTEMBER 2015
www.ti.com
11 Device and Documentation Support
11.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.2 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
14
Submit Documentation Feedback
Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM3480
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM3480IM3-12
NRND
SOT-23
DBZ
3
1000
TBD
Call TI
Call TI
-40 to 125
L0C
LM3480IM3-12/NOPB
ACTIVE
SOT-23
DBZ
3
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0C
LM3480IM3-15/NOPB
ACTIVE
SOT-23
DBZ
3
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0D
LM3480IM3-3.3
NRND
SOT-23
DBZ
3
1000
TBD
Call TI
Call TI
-40 to 125
L0A
LM3480IM3-3.3/NOPB
ACTIVE
SOT-23
DBZ
3
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0A
LM3480IM3-5.0
NRND
SOT-23
DBZ
3
1000
TBD
Call TI
Call TI
-40 to 125
L0B
LM3480IM3-5.0/NOPB
ACTIVE
SOT-23
DBZ
3
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0B
LM3480IM3X-12
NRND
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
-40 to 125
L0C
LM3480IM3X-12/NOPB
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0C
LM3480IM3X-15/NOPB
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0D
LM3480IM3X-3.3
NRND
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
-40 to 125
L0A
LM3480IM3X-3.3/NOPB
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0A
LM3480IM3X-5.0
NRND
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
-40 to 125
L0B
LM3480IM3X-5.0/NOPB
ACTIVE
SOT-23
DBZ
3
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0B
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2015
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Oct-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LM3480IM3-12
SOT-23
DBZ
3
1000
178.0
8.4
LM3480IM3-12/NOPB
SOT-23
DBZ
3
1000
178.0
LM3480IM3-15/NOPB
SOT-23
DBZ
3
1000
178.0
LM3480IM3-3.3
SOT-23
DBZ
3
1000
LM3480IM3-3.3/NOPB
SOT-23
DBZ
3
W
Pin1
(mm) Quadrant
3.3
2.9
1.22
4.0
8.0
Q3
8.4
3.3
2.9
1.22
4.0
8.0
Q3
8.4
3.3
2.9
1.22
4.0
8.0
Q3
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
1000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3-5.0
SOT-23
DBZ
3
1000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3-5.0/NOPB
SOT-23
DBZ
3
1000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-12
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-12/NOPB
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-15/NOPB
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-3.3
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-3.3/NOPB
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-5.0
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
LM3480IM3X-5.0/NOPB
SOT-23
DBZ
3
3000
178.0
8.4
3.3
2.9
1.22
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Oct-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM3480IM3-12
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3-12/NOPB
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3-15/NOPB
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3-3.3
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3-3.3/NOPB
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3-5.0
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3-5.0/NOPB
SOT-23
DBZ
3
1000
210.0
185.0
35.0
LM3480IM3X-12
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM3480IM3X-12/NOPB
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM3480IM3X-15/NOPB
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM3480IM3X-3.3
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM3480IM3X-3.3/NOPB
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM3480IM3X-5.0
SOT-23
DBZ
3
3000
210.0
185.0
35.0
LM3480IM3X-5.0/NOPB
SOT-23
DBZ
3
3000
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages