Sensitron B1215HD2U Fixed input, 3000v isolation, unregulated, single output Datasheet

SENSITRON
SEMICONDUCTOR
B - 1W/2W Series
TECHNICAL DATA
DATA SHEET 1101, REV. A
DC-DC Converters
Fixed Input, 3000V Isolation, Unregulated, Single Output
FEATURES:
•
•
•
•
•
•
•
•
•
•
•
•
Isolation Voltage:
Isolation Resistance (1):
Short-Circuit Duration:
Case Temperature Rise:
Cooling Method:
Standby Power Dissipation:
Operating Temp.:
Storage Temp.:
Humidity:
Soldering Temp. (2):
Case Material:
Mean Time Before Failure:
3000Vdc
1000MΩ
1 second
Max. 25°C, Typ. 15°C
Free-Air Cooling
1W (100mW), 2W (200mW)
-40°C ~ + 85°C
-55°C ~ + 125°C
≤ 95%
300°C
Non-Flammable Material (UL94-V0)
> 1,000,000 hours (Operating Temp. 25°C)
B Single Output-1W/2W Series Input Characteristics
Part Number
Nominal Input Voltage Input Voltage Range
Maximum Input Voltage*
B05XXHS/D1/2U
5Vdc
4.5~5.5Vdc
7Vdc
B12XXHS/D1/2U
12Vdc
10.8~13.2Vdc
15Vdc
B24XXHS/D1/2U
24Vdc
21.6~26.4Vdc
28Vdc
* Voltage above this value may cause permanent damage to the device.
B Single Output-1W/2W Series Output Characteristics
Parameter
MIN
TYP
0.25
1
W
2W Output Power
0.5
2
W
+ 1.2
%
85
%
0.03
%/°C
mVp-p
Efficiency at 100% Load
65
75
Temperature Coefficient
1W Ripple and Noise
50
75
2W Ripple and Noise
85
150
100
150
Switching Frequency
2.
Units
1W Output Power
Line Regulation
1.
MAX
80
kHz
All specifications at TA=25°C, 75% of the humidity, Nominal input voltage, full output load unless otherwise
specified.
Soldering for 10 seconds at 1.5mm away from the edge.
• 221 West Industry Court • Deer Park, NY 11729-4681 • Phone (631) 586-7600 • Fax (631) 242-9798 •
• World Wide Web Site - http://www.sensitron.com • E-Mail Address - [email protected] •
SENSITRON
SEMICONDUCTOR
B – 1W/2W Series
TECHNICAL DATA
DATA SHEET 1101, REV. A
B Single Output-1W/2W Series Part Number List
Input
5Vdc
12Vdc
24Vdc
Output
Power
5V/200m A
1.00W
9V/111m A
1.00W
12V/84m A
1.00W
SIP-1W
SIP-2W
DIP-1W
DIP-2W
B0505HS1U
B0505HS2U
B0505HD1U
B0505HD2U
B0509HS1U
B0509HS2U
B0509HD1U
B0509HD2U
B0512HS1U
B0512HS2U
B0512HD1U
B0512HD2U
B0515HS1U
B0515HS2U
B0515HD1U
B0515HD2U
B1205HS1U
B1205HS2U
B1205HD1U
B1205HD2U
B1209HS1U
B1209HS2U
B1209HD1U
B1209HD2U
15V/67m A
1.00W
5V/400m A
2.00W
B1212HS1U
B1212HS2U
B1212HD1U
B1212HD2U
9V/222m A
2.00W
B1215HS1U
B1215HS2U
B1215HD1U
B1215HD2U
12V/167m A
2.00W
B2405HS1U
B2405HS2U
B2405HD1U
B2405HD2U
15V/133m A
2.00W
B2409HS1U
B2409HS2U
B2409HD1U
B2409HD2U
B2412HS1U
B2412HS2U
B2412HD1U
B2412HD2U
B2415HS1U
B2415HS2U
B2415HD1U
B2415HD2U
PIN CONFIGURATION
BxxyyHS1/2U PACKAGE DIMENSIONS
BxxyyHD1/2U PACKAGE DIMENSIONS
• 221 West Industry Court • Deer Park, NY 11729-4681 • Phone (631) 586-7600 • Fax (631) 242-9798 •
• World Wide Web Site - http://www.sensitron.com • E-Mail Address - [email protected] •
SENSITRON
SEMICONDUCTOR
B - 1W/2W Series
TECHNICAL DATA
DATA SHEET 1101, REV. A
Mechanical Dimension: mm
BxxyyHS1/2U PACKAGE DIMENTIONS
BxxyyHD1/2U PACKAGE DIMENTIONS
19.60±0.15
20.40±0.15
10.00±0.15
8.20±0.15
4.10±0.10
4.10±0.10
1 2
5
7
7.00±0.15
10.00±0.15
1
14
7
10
7.62±0.15
8
1.25±0.10
2.00±0.10
15.24±0.15
15.24±0.15
DIMENSIONAL RECOMMENDATIONS FOR PCB LAYOUT
SIP PACKAGE DIMENSIONS
DIP PACKAGE DIMENSIONS
• 221 West Industry Court • Deer Park, NY 11729-4681 • Phone (631) 586-7600 • Fax (631) 242-9798 •
• World Wide Web Site - http://www.sensitron.com • E-Mail Address - [email protected] •
SENSITRON
SEMICONDUCTOR
B - 1W/2W Series
TECHNICAL DATA
DATA SHEET 1101, REV. A
APPLICATION NOTE
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the DC/DC output end
and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper.
If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and
reliable operation is ensured, the greatest capacitance of its filter capacitor sees the external capacitor table. To get
an extremely low ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC
converter, which may produce a more significant filtering effect. It should also be noted that the inductance and the
frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference
(see figure 1).
Requirement On Output Load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC
converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input
voltage is not exceeded, the minimum output load is not less than 10% of the full load, and that this product should
never be operated under no load! If the actual output power is very small, please connect a resistor with proper
resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output
power.
Overload Protection
Under normal operating conditions, the output circuit of these products has no protection against over-current and
short-circuits. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit
breaker to the circuit.
Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage
regulator with overheat protection that is connected to the input or output end in series (see Figure 2).
BxxyyHS/D1/2U
External Capacitor Table
External
Vin
Vout
capaticor
5 VDC
4.7 uF
5 VDC
12 VDC
2.2 uF
9 VDC
24 VDC
1 uF
12 VDC
15 VDC
External
capaticor
10 uF
4.7 uF
2.2 uF
1 uF
• 221 West Industry Court • Deer Park, NY 11729-4681 • Phone (631) 586-7600 • Fax (631) 242-9798 •
• World Wide Web Site - http://www.sensitron.com • E-Mail Address - [email protected] •
SENSITRON
SEMICONDUCTOR
B - 1W/2W Series
TECHNICAL DATA
DATA SHEET 1101, REV. A
DISCLAIMER:
1- The information given herein, including the specifications and dimensions, is subject to change without prior not ice to
improve product characteristics. Before ordering, purchasers are advised to contact the Sensitron Semiconductor sales
department for the latest version of the datasheet(s).
2- In cases where extremely high reliability is required (such as use in nuclear power control, aerospace and aviation,
traffic equipment, medical equipment , and safety equipment) , safety should be ensured by using semiconductor devices
that feature assured safety or by means of users’ fail-safe precautions or other arrangement .
3- In no event shall Sensitron Semiconductor be liable for any damages that may result from an accident or any other
cause during operation of the user’s units according to the datasheet(s). Sensitron Semiconductor assumes no
responsibility for any intellectual property claims or any other problems that may result from applications of information,
products or circuits described in the datasheets.
4- In no event shall Sensitron Semiconductor be liable for any failure in a semiconductor device or any secondary damage
resulting from use at a value exceeding the absolute maximum rating.
5- No license is granted by the datasheet(s) under any patents or other rights of any third party or Sensitron
Semiconductor.
6- The datasheet(s) may not be reproduced or duplicated, in any form, in whole or part, without the expressed writ ten
permission of Sensitron Semiconductor.
7- The products (technologies) described in the datasheet(s) are not to be provided to any party whose purpose in their
application will hinder maintenance of international peace and safety nor are they to be applied to that purpose by their
direct purchasers or any third party. When exporting these products (technologies), the necessary procedures are to be
taken in accordance with related laws and regulations.
• 221 West Industry Court • Deer Park, NY 11729-4681 • Phone (631) 586-7600 • Fax (631) 242-9798 •
• World Wide Web Site - http://www.sensitron.com • E-Mail Address - [email protected]
Similar pages