ON MT9P031I12STC-DR 1/2.5-inch 5 mp cmos digital image sensor Datasheet

MT9P031
1/2.5-Inch 5 Mp CMOS
Digital Image Sensor
General Description
www.onsemi.com
The ON Semiconductor MT9P031 is a 1/2.5−inch CMOS
active−pixel digital image sensor with an active imaging pixel array of
2592 H x 1944 V. It incorporates sophisticated camera functions
on−chip such as windowing, column and row skip mode, and snapshot
mode. It is programmable through a simple two−wire serial interface.
The 5 Mp CMOS image sensor features ON Semiconductor’s
breakthrough low−noise CMOS imaging technology that achieves
CCD image quality (based on signal−to−noise ratio and low−light
sensitivity) while maintaining the inherent size, cost, and integration
advantages of CMOS.
Applications
Value
Optical Format
1/2.5-inch (4:3)
Active Imager Size
5.70 mm (H) x 4.28 mm (V)
7.13 mm Diagonal
Active Pixels
2592 H x 1944 V
Pixel Size
2.2 x 2.2 μm
Color Filter Array
RGB Bayer Pattern
Shutter Type
Global Reset Release (GRR),
Snapshot Only
Electronic Rolling Shutter (ERS)
Maximum Data Rate / Pixel Clock
96 Mp/s at 96 MHz (2.8 V I/O)
48 Mp/s at 48 MHz (1.8 V I/O)
Frame Rate
Programmable up to 14 fps
HDTV (640 x 480,
with binning)
Programmable up to 53 fps
12-bit, On-chip
Responsivity
1.4 V/lux-sec (550 nm)
Pixel Dynamic Range
70.1 dB
SNRMAX
38.1 dB
I/O
1.7−3.1 V
Digital
1.7−1.9 V (1.8 V Nominal)
Analog
2.6−3.1 V (2.8 V Nominal)
•
•
•
•
•
Full Resolution
ADC Resolution
Supply Voltage
ORDERING INFORMATION
See detailed ordering and shipping information on page 2 of
this data sheet.
Table 1. KEY PERFORMANCE PARAMETERS
Parameter
ILCC48 10x10
CASE 847AA
•
Features
•
•
•
•
•
•
•
•
Power Consumption
381 mW at 14 fps Full Resolution
Operating Temperature
–30°C to +70°C
Packaging
48-pin iLCC, Die
•
•
•
•
•
© Semiconductor Components Industries, LLC, 2006
January, 2017 − Rev. 10
1
High Resolution Network Cameras
Wide FOV Cameras
720 P–60 fps Cameras
Dome Cameras with Electronic Pan, Tile,
and Zoom
Hybrid Video Cameras with High
Resolution Stills
Detailed Feature Extraction for Smart
Cameras
High Frame Rate
Superior Low-light Performance
Low Dark Current
Global Reset Release, which Starts the
Exposure of All Rows Simultaneously
Bulb Exposure Mode, for Arbitrary
Exposure Times
Snapshot Mode to Take Frames on Demand
Horizontal and Vertical Mirror Image
Column and row skip modes to reduce
image size without reducing field−of−view
(FOV)
Column and Row Binning Modes to
Improve Image Quality when Resizing
Simple Two-wire Serial Interface
Programmable Controls: Gain, Frame Rate,
Frame Size, Exposure
Automatic Black Level Calibration
On-chip Phase-Locked Loop (PLL)
Publication Order Number:
MT9P031/D
MT9P031
ORDERING INFORMATION
Table 2. AVAILABLE PART NUMBERS
Part Number
Product Description
Orderable Product Attribute Description
MT9P031D00STCC18BC1−200
5 MP 1/3” CIS
Die Sales, 200mm Thickness
MT9P031D00STMC18BC1−200
5 MP 1/3” CIS
Die Sales, 200mm Thickness
MT9P031I12STC−DP
5 MP 1/3” CIS
Dry Pack with Protective Film
MT9P031I12STC−DR
5 MP 1/3” CIS
Dry Pack without Protective Film
MT9P031I12STC−DR1
5 MP 1/3” CIS
Dry Pack Single Tray without Protective Film
MT9P031I12STC−TP
5 MP 1/3” CIS
Tape & Reel with Protective Film
MT9P031I12STM−DP
5 MP 1/3” CIS
Dry Pack with Protective Film
MT9P031I12STM−DP1
5 MP 1/3” CIS
Dry Pack Single Tray with Protective Film
MT9P031I12STM−DR
5 MP 1/3” CIS
Dry Pack without Protective Film
MT9P031I12STM−DR1
5 MP 1/3” CIS
Dry Pack Single Tray without Protective Film
DESCRIPTION
The MT9P031 sensor can be operated in its default mode
or programmed by the user for frame size, exposure, gain
setting, and other parameters. The default mode outputs a
full resolution image at 14 frames per second (fps).
An on−chip analog−to−digital converter (ADC) provides
12 bits per pixel. FRAME_VALID (FV) and LINE_VALID
(LV) signals are output on dedicated pins, along with a pixel
clock that is synchronous with valid data.
The MT9P031produces extraordinarily clear, sharp
digital pictures, and its ability to capture both continuous
video and single frames makes it the perfect choice for a
wide range of consumer and industrial applications,
including cell phones, digital still cameras, digital video
cameras, and PC cameras..
FUNCTIONAL OVERVIEW
The MT9P031 is a progressive−scan sensor that generates
a stream of pixel data at a constant frame rate. It uses an
on−chip, phase−locked loop (PLL) to generate all internal
clocks from a single master input clock running between
6 and 27 MHz. The maximum pixel rate is 96 Mp/s,
corresponding to a clock rate of 96 MHz. Figure 1 illustrates
a block diagram of the sensor.
Array Control
TRIGGER
Pixel Array
EXTCLK
RESET_BAR
STANDBY_BAR
OE
Output
2752H x 2004V
Serial
Interface
Analog Signal Chain
Data Path
SCLK
S DATA
SADDR
PIXCLK
DOUT [11:0]
LV
FV
STROBE
Figure 1. Block Diagram
and then reading each row in turn. In the time interval
between resetting a row and reading that row, the pixels in
the row integrate incident light. The exposure is controlled
by varying the time interval between reset and readout. Once
a row has been read, the data from the columns is sequenced
User interaction with the sensor is through the two−wire
serial bus, which communicates with the array control,
analog signal chain, and digital signal chain. The core of the
sensor is a 5 Mp active−pixel array. The timing and control
circuitry sequences through the rows of the array, resetting
www.onsemi.com
2
MT9P031
through an analog signal chain (providing offset correction
and gain), and then through an ADC. The output from the
ADC is a 12−bit value for each pixel in the array. The ADC
output passes through a digital processing signal chain
(which provides further data path corrections and applies
digital gain). The pixel data are output at a rate of up to
96 Mp/s, in addition to frame and line synchronization
signals.
VDD_PLL
VAA_PIX
VAA
VDD
VDD_IO
1.0kΩ
1.5kΩ1
1.5kΩ1
VDD_IO 2,3 VDD2,3 VAA2,3
SADDR
RESET_BAR
STANDBY_BAR
DOUT [11:0]
PIXCLK
FV
LV
STROBE
1μF
SCLK
S DATA
TRIGGER
From
controller
Master
clock
To
controller
EXTCLK
TEST
AGND3
RSVD
DGND3
OE
Figure 2. Typical Configuration (Connection)
48
48
47
46
45
DOUT 9
1
DOUT 10
2
DOUT 11
A GND
3
DGND
TEST
4
VDD
SCLK
5
VAA_PIX
SDATA
6
VAA_PIX
RSVD
Notes:
1. A resistor value of 1.5 kΩ is recommended, but may be greater for slower two-wire speed.
2. All power supplies should be adequately decoupled.
3. All DGND pins must be tied together, as must all AGND pins, all VDD_IO pins, and all VDD pins.
44
43
FRAME_VALID
7
42
DOUT8
LINE_VALID
8
41
DOUT7
9
40
DOUT6
DGND
10
39
VDD_IO
VDD_ IO
11
38
DOUT5
VDD
12
37
DOUT4
DOUT3
STROBE
OE
17
PIXCLK
NC
18
31
EXTCLK
19
20
21
22
23
24
25
26
27
28
29
30
NC
DOUT0
32
NC
33
NC
16
NC
RESET_BAR
DGND
DOUT1
VDD_PLL
34
VAA
15
VAA
DOUT2
TRIGGER
AGND
35
TEST
14
TEST
13
STANDBY_BAR
NC
SADDR
36
Figure 3. 48-Pin iLCC 10 x 10 Package Pinout Diagram (Top View)
www.onsemi.com
3
MT9P031
Table 3. PIN DESCRIPTION
Name
Type
RESET_BAR
Input
When LOW, the MT9P031 asynchronously resets. When driven HIGH,
it resumes normal operation with all configuration registers set to factory
defaults.
Description
EXTCLK
Input
External input clock.
SCLK
Input
Serial clock. Pull to VDD_IO with a 1.5 kΩ resistor.
OE
Input
When HIGH, the PIXCLK, DOUT, FV, LV, and STROBE outputs enter a High-Z.
When driven LOW, normal operation resumes.
STANDBY_BAR
Input
Standby. When LOW, the chip enters a low-power standby mode. It resumes
normal operation when the pin is driven HIGH.
TRIGGER
Input
Snapshot trigger. Used to trigger one frame of output in snapshot modes,
and to indicate the end of exposure in bulb exposure modes.
SADDR
Input
Serial address. When HIGH, the MT9P031 responds to device ID (BA)H.
When LOW, it responds to serial device ID (90)H.
SDATA
I/O
PIXCLK
Output
Pixel clock. The DOUT, FV, LV, and STROBE outputs should be captured on the
falling edge of this signal.
DOUT[11:0]
Output
Pixel data. Pixel data is 12-bit. MSB (DOUT11) through LSB (DOUT0) of each
pixel, to be captured on the falling edge of PIXCLK.
FRAME_VALID
Output
Frame valid. Driven HIGH during active pixels and horizontal blanking of each
frame and LOW during vertical blanking.
LINE_VALID
Output
Line valid. Driven HIGH with active pixels of each line and LOW during
blanking periods.
STROBE
Output
Snapshot strobe. Driven HIGH when all pixels are exposing in snapshot
modes.
VDD
Supply
Digital supply voltage. Nominally 1.8 V.
VDD_IO
Supply
IO supply voltage. Nominally 1.8 or 2.8 V.
DGND
Supply
Digital ground.
VAA
Supply
Analog supply voltage. Nominally 2.8 V.
VAA_PIX
Supply
Pixel supply voltage. Nominally 2.8 V, connected externally to VAA.
Serial data. Pull to VDD_IO with a 1.5 kΩ resistor.
AGND
Supply
Analog ground.
VDD_PLL
Supply
PLL supply voltage. Nominally 2.8 V, connected externally to VAA.
TEST
−
Tie to AGND for normal device operation (factory use only).
RSVD
−
Tie to DGND for normal device operation (factory use only).
NC
−
No connect.
www.onsemi.com
4
MT9P031
PIXEL DATA FORMAT
Pixel Array Structure
The MT9P031 pixel array consists of a 2752−column by
2004−row matrix of pixels addressed by column and row.
The address (column 0, row 0) represents the upper−right
corner of the entire array, looking at the sensor, as shown in
Figure 4.
The array consists of a 2592−column by 1944−row active
region in the center representing the default output image,
surrounded by a boundary region (also active), surrounded
by a border of dark pixels (see Table 4 and Table 5). The
boundary region can be used to avoid edge effects when
doing color processing to achieve a 2592 x 1944 result
image, while the optically black column and rows can be
used to monitor the black level.
Pixels are output in a Bayer pattern format consisting of
four “colors”−GreenR, GreenB, Red, and Blue (Gr, Gb, R,
B)−representing three filter colors. When no mirror modes
are enabled, the first row output alternates between Gr and
R pixels, and the second row output alternates between B
and Gb pixels. The Gr and Gb pixels have the same color
filter, but they are treated as separate colors by the data path
and analog signal chain.
Table 4. PIXEL TYPE BY COLUMN
Column
Pixel Type
0–9
Dark (10)
10–15
Active boundary (6)
16–2607
Active image (2592)
2608–2617
Active boundary (10)
2618–2751
Dark (134)
Table 5. PIXEL TYPE BY ROW
Column
Pixel Type
0–49
Dark (50)
50–53
Active boundary (4)
54–1997
Active image (1944)
1998–2001
Active boundary (3)
2002–2003
Dark (2)
(0,0)
50 black rows
4
(16,54)
Active Image
134 black columns
10
2592 x 1944
active pixels
6
10 black columns
4
2 black rows
(2751, 2003)
Figure 4. Pixel Array Description
column readout direction
..
black pixels
.
Gr R Gr R Gr R Gr
row
readout
direction
First clear
pixel (10,50)
B Gb B Gb B Gb B
... Gr R Gr R Gr R Gr
B Gb B Gb B Gb B
Gr R Gr R Gr R Gr
B Gb B Gb B Gb B
..
.
Figure 5. Pixel Color Pattern Detail (Top Right Corner)
www.onsemi.com
5
MT9P031
Default Readout Order
When the sensor is imaging, the active surface of the
sensor faces the scene as shown in Figure 5. When the image
is read out of the sensor, it is read one row at a time, with the
rows and columns sequenced as shown in Figure 6.
By convention, the sensor core pixel array is shown with
pixel (0,0) in the top right corner (see Figure 4). This reflects
the actual layout of the array on the die. Also, the first pixel
data read out of the sensor in default condition is that of pixel
(16, 54).
Lens
Scene
Sensor (rear view)
Row
Readout
Order
Column Readout Order Pixel (0,0)
Figure 6. Imaging a Scene
Output Data Format (Default Mode)
and vertical blanking, as shown in Figure 7. LV is HIGH
during the shaded region of the figure. FV timing is
described in “Output Data Timing”.
The MT9P031 image data is read out in a progressive
scan. Valid image data is surrounded by horizontal blanking
P0,0 P0,1 P0,2 .....................................P0,n−1 P0,n
P1,0 P1,1 P1,2 .....................................P1,n−1 P1,n
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
VALID IMAGE
HORIZONTAL
BLANKING
Pm−1,0 Pm−1,1 .....................................Pm−1,n−1Pm−1,n
Pm,0 Pm,1 .....................................Pm,n−1 Pm,n
00 00 00 ..................................... 00 00 00
00 00 00 ..................................... 00 00 00
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
VERTICAL/HORIZONTAL
BLANKING
VERTICAL BLANKING
00 00 00 ..................................... 00 00 00
00 00 00 ..................................... 00 00 00
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
Figure 7. Spatial Illustration of Image Readout
www.onsemi.com
6
MT9P031
Readout Sequence
Columns are read out in the following order:
1. Dark columns:
If either Show_Dark_Columns or Row_BLC is
set, dark columns on the left side of the image are
read out followed by those on the right side. The
set of columns read is shown in Table 7. The
Column_Skip setting is ignored for the dark
columns.
If neither Show_Dark_Columns nor Row_BLC is
set, no dark columns are read, allowing all
columns to be part of the active image. This does
not change the row time, as WDC is included in the
vertical blank period.
2. Active image:
The columns defined by column start, column size,
bin, skip, and column mirror settings are read out.
If this set of columns includes the columns read
out above, these columns are resampled, meaning
the data is invalid.
Typically, the readout window is set to a region including
only active pixels. The user has the option of reading out
dark regions of the array, but if this is done, consideration
must be given to how the sensor reads the dark regions for
its own purposes.
Rows are read from the array in the following order:
1. Dark rows:
If Show_Dark_Rows is set, or if Manual_BLC is
clear, dark rows on the top of the array are read
out. The set of rows sampled are adjusted based on
the Row_Bin setting such that there are 8 rows
after binning, as shown in the Table 6. The
Row_Skip setting is ignored for the dark row
region.
If Show_Dark_Rows is clear and Manual_BLC is
set, no dark rows are read from the array as part of
this step, allowing all rows to be part of the active
image. This does not change the frame time, as
HDR is included in the vertical blank period.
2. Active image:
The rows defined by the row start, row size, bin,
skip, and row mirror settings are read out. If this
set of rows includes rows read out above, those
rows are resampled, meaning that the data is
invalid.
Table 7. DARK COLUMNS SAMPLED AS
A FUNCTION OF COLUMN_BIN
Column_Bin
WDC (Dark Columns After Binning)
0
80
1
40
3
20
Table 6. DARK ROWS SAMPLED AS A FUNCTION
OF ROW_BIN
Row_Bin
HDR (Dark Rows After Binning)
0
8
1
8
3
8
www.onsemi.com
7
MT9P031
OUTPUT DATA TIMING
The output images are divided into frames, which are
further divided into lines. By default, the sensor produces
1944 rows of 2592 columns each. The FV and LV signals
indicate the boundaries between frames and lines,
respectively. PIXCLK can be used as a clock to latch the
data. For each PIXCLK cycle, one 12−bit pixel datum
outputs on the DOUT pins. When both FV and LV are
asserted, the pixel is valid. PIXCLK cycles that occur when
FV is negated are called vertical blanking. PIXCLK cycles
that occur when only LV is negated are called horizontal
blanking.
PIXCLK
FV
LV
D OUT [11:0]
P0
Vertical Blanking
Horiz Blanking
P1
P2
P3
P4
Valid Image Data
Pn
Horiz Blanking
Vertical Blanking
Figure 8. Default Pixel Output Timing
LV and FV
will be extended back to include them; in this case, the first
pixel of the active image still occurs at the same position
relative to the leading edge of FV. Normally, LV will only be
asserted if FV is asserted; this is configurable as described
below.
The timing of the FV and LV outputs is closely related to
the row time and the frame time.
FV will be asserted for an integral number of row times,
which will normally be equal to the height of the output
image. If Show_Dark_Rows is set, the dark sample rows
will be output before the active image, and FV will be
extended to include them. In this case, FV’s leading edge
happens at time 0.
LV will be asserted during the valid pixels of each row.
The leading edge of LV will be offset from the leading edge
of FV by 609 PIXCLKs. If Show_Dark_Columns is set, the
dark columns will be output before the image pixels, and LV
LV Format Options
The default situation is for LV to be negated when FV is
negated. The other option available is shown in Figure 9. If
Continuous_LV is set, LV is asserted even when FV is not,
with the same period and duty cycle. If XOR_Line_Valid is
set, but not Continuous_Line_Valid, the resulting LV will be
the XOR of FV and the continuous LV.
FV
Default
LV
FV
Continuous LV
LV
FV
XOR LV
LV
Figure 9. LV Format Options
The timing of an entire frame is shown in Figure 10.
www.onsemi.com
8
MT9P031
t ROW
W
WDC
LV
Dark Columns
FV
Dark Rows
Row Readout
H
t FRAME
HDR
Column Readout
Active Image
Blanking Region
Figure 10. Frame Timing
rate of 1 pixel per PIXCLK. One row time (tROW) is the
period from the first pixel output in a row to the first pixel
output in the next row. The row time and frame time are
defined by equations in Table 8.
Frame Time
The pixel clock (PIXCLK) represents the time needed to
sample 1 pixel from the array, and is typically equal to 1
EXTCLK period. The sensor outputs data at the maximum
Table 8. FRAME TIME
Parameters
Name
Equation
fps
Frame Rate
1/tFRAME
tFRAME
Frame Time
(H + max(VB, VBMIN)) × tROW
14
71.66 ms
tROW
Row Time
W
Output Image Width
2 × ceil((Column_Size + 1) / (2 × (Column_Skip + 1)))
2 × ceil((Row_Size + 1) / (2 × (Row_Skip + 1)))
1944 rows
max (1, (2 * 16 × Shutter_Width_Upper)
+ Shutter_Width_Lower)
1943 rows
Horizontal_Blank + 1
1 PIXCLK
H
Output Image Height
SW
Shutter Width
HB
Horizontal Blanking
VB
Vertical Blanking
HBMIN
Minimum Horizontal Blanking
VBMIN
Minimum Vertical Blanking
tPIXCLK
Pixclk Period
tPIXCLK
Default Timing at
EXTCLK = 96 MHz
2×
x max(((W/2) + max(HB, HBMIN)),
(41 + 346 x (Row_Bin+1) + 99))
Vertical_Blank + 1
346 × (Row_Bin + 1) + 64 + (WDC / 2)
max (8, SW − H) + 1
1/fPIXCLK
The minimum horizontal blanking (HBMIN) values for
various Row_Bin and Column_Bin settings are shown in
Table 9.
www.onsemi.com
9
36.38 μs
2592 PIXCLK
26 rows
450 PIXCLK
9 rows
10.42 ns
MT9P031
Table 9. HBMIN VALUES FOR ROW_BIN VS. COLUMN_BIN SETTINGS
Column_bin (WDC)
Row_bin
0
1
3
0
450
430
420
1
796
776
766
3
1488
1468
1458
Frame Rates at Common Resolutions
rates are shown both with subsampling enabled and
disabled.
Table 10 and Table 11 show examples of register settings
to achieve common resolutions and their frame rates. Frame
Table 10. STANDARD RESOLUTIONS
Frame
Rate
Sub−
sampling
Mode
Column_
Size
(R0x04)
Row_
Size
(R0x03)
Shutter_
Width_
Lower
(R0x09)
Row_
Bin
(R0x22
[5:4])
Row_
Skip
(R0x22
[2:0])
Column_
Bin
(R0x23
[5:4])
Column_
Skip
(R0x23
[2:0])
2592 x 1944
(Full Resolution)
14
N/A
2591
1943
<1943
0
0
0
0
2048 x 1536 QXGA
21
N/A
2047
1535
<1535
0
0
0
0
1600 x 1200 UXGA
31
N/A
1599
1199
<1199
0
0
0
0
1280 x 1024 SXGA
42
N/A
1279
1023
<1023
0
0
0
0
1024 x 768 XGA
63
N/A
1023
767
<767
0
0
0
0
63
skipping
2047
1535
0
1
0
1
47
binning
2047
1535
1
1
1
1
0
0
0
0
0
1
0
1
1
1
1
1
0
0
0
0
Resolution
800 x 600 SVGA
640 x 480 VGA
90
N/A
799
599
90
skipping
1599
1199
<599
65
binning
1599
1199
123
N/A
639
479
123
skipping
2559
1919
0
3
0
3
53
binning
2559
1919
3
3
3
3
<479
Table 11. WIDE SCREEN (16:9) RESOLUTIONS
Frame
Rate
Sub−
sampling
Mode
Column_
Size
(R0x04)
Row_
Size
(R0x03)
Shutter_
Width_
Lower
(R0x09)
Row_
Bin
(R0x22
[5:4])
Row_
Skip
(R0x22
[2:0])
Column_
Bin
(R0x23
[5:4])
Column_
Skip
(R0x23
[2:0])
1920 x 1080 HDTV
31
N/A
1919
1079
<1079
0
0
0
0
1280 x 720 HDTV
60
N/A
1279
719
<719
0
0
0
0
60
skipping
2559
1439
<719
0
1
0
1
45
skipping
2559
1439
<719
1
1
1
1
Resolution
1. It is assumed that the minimum horizontal blanking and the minimum vertical blanking conditions are met, and that all other registers are
set to default values.
www.onsemi.com
10
MT9P031
SERIAL BUS DESCRIPTION
Registers are written to and read from the MT9P031
through the two−wire serial interface bus. The MT9P031 is
a serial interface slave and is controlled by the serial clock
(SCLK), which is driven by the serial interface master. Data
is transferred into and out of the MT9P031 through the serial
data (SDATA) line. The SDATA line is pulled up to
VDD_IO offchip by a 1.5 kΩ resistor. Either the slave or
master device can pull the SDATA line LOW−the serial
interface protocol determines which device is allowed to
pull the SDATA line down at any given time.
Bus Idle State
The bus is idle when both the data and clock lines are
HIGH. Control of the bus is initiated with a start bit, and the
bus is released with a stop bit. Only the master can generate
the start and stop bits.
Start Bit
The start bit is defined as a HIGH−to−LOW transition of
the data line while the clock line is HIGH.
Stop Bit
The stop bit is defined as a LOW−to−HIGH transition of
the data line while the clock line is HIGH.
Protocol
The two-wire serial defines several different transmission
codes, as follows:
1. a start bit
2. the slave device 8-bit address
3. an (a no) acknowledge bit
4. an 8-bit message
5. a stop bit
Slave Address
The 8−bit address of a two−wire serial interface device
consists of 7 bits of address and 1 bit of direction. A “0” in
the LSB (least significant bit) of the address indicates write
mode (0xBA), and a “1” indicates read mode (0xBB).
Data Bit Transfer
Sequence
One data bit is transferred during each clock pulse. The
serial interface clock pulse is provided by the master. The
data must be stable during the HIGH period of the two−wire
serial interface clock−it can only change when the serial
clock is LOW. Data is transferred 8 bits at a time, followed
by an acknowledge bit.
A typical READ or WRITE sequence begins by the
master sending a start bit. After the start bit, the master sends
the slave device’s 8−bit address. The last bit of the address
determines if the request is a READ or a WRITE, where a
“0” indicates a WRITE and a “1”indicates a READ. The
slave device acknowledges its address by sending an
acknowledge bit back to the master.
If the request is a WRITE, the master then transfers the
8−bit register address to which a WRITE should take place.
The slave sends an acknowledge bit to indicate that the
register address has been received. The master then transfers
the data 8 bits at a time, with the slave sending an
acknowledge bit after each 8 bits. The MT9P031 uses 16−bit
data for its internal registers, thus requiring two 8−bit
transfers to write to one register. After 16 bits are transferred,
the register address is automatically incremented, so that the
next 16 bits are written to the next register address. The
master stops writing by sending a start or stop bit.
A typical READ sequence is executed as follows. First the
master sends the write−mode slave address and 8−bit
register address, just as in the WRITE request. The master
then sends a start bit and the read−mode slave address. The
master then clocks out the register data 8 bits at a time. The
master sends an acknowledge bit after each 8−bit transfer.
The register address is automatically−incremented after
every 16 bits is transferred. The data transfer is stopped
when the master sends a no−acknowledge bit.
Acknowledge Bit
The master generates the acknowledge clock pulse. The
transmitter (which is the master when writing, or the slave
when reading) releases the data line, and the receiver
indicates an acknowledge bit by pulling the data line LOW
during the acknowledge clock pulse.
No-Acknowledge Bit
The no−acknowledge bit is generated when the data line
is not pulled down by the receiver during the acknowledge
clock pulse. A no−acknowledge bit is used to terminate a
read sequence.
www.onsemi.com
11
MT9P031
TWO-WIRE SERIAL INTERFACE SAMPLE WRITE AND READ SEQUENCES
16-Bit WRITE Sequence
A typical WRITE sequence for writing 16 bits to a register
is shown in Figure 11. A start bit given by the master,
followed by the write address, starts the sequence. The
image sensor then gives an acknowledge bit and expects the
register address to come first, followed by the 16−bit data.
After each 8−bit transfer, the image sensor gives an
acknowledge bit. All 16 bits must be written before the
register is updated. After 16 bits are transferred, the register
address is automatically incremented so that the next 16 bits
are written to the next register. The master stops writing by
sending a start or stop bit.
SCLK
SDATA
START
0000 0010
Reg0x09
0xBA ADDR
ACK
ACK
1000 0100
ACK
STOP
ACK
Figure 11. Timing Diagram Showing a WRITE to Reg0x09 with the Value 0x0284
16-Bit READ Sequence
then clocks out the register data 8 bits at a time. The master
sends an acknowledge bit after each 8-bit transfer. The
register address should be incremented after every 16 bits is
transferred. The data transfer is stopped when the master
sends a no-acknowledge bit.
A typical READ sequence is shown in Figure 12. First the
master has to write the register address, as in a WRITE
sequence. Then a start bit and the read address specify that
a READ is about to happen from the register. The master
SCLK
SDATA
0xBA ADDR
START
0xBB ADDR
Reg0x09
ACK
ACK START
0000 0010
ACK
1000 0100
ACK
Figure 12. Timing Diagram Showing a READ to Reg0x09 with the Value 0x0284
www.onsemi.com
12
STOP
NACK
MT9P031
FEATURES
Reset
Power Up and Power Down
The MT9P031 may be reset by using RESET_BAR
(active LOW) or the reset register.
When first powering on the MT9P031, follow this
sequence:
1. Ensure RESET_BAR is asserted (LOW).
2. Bring up the supplies. If both the analog and the
digital supplies cannot be brought up
simultaneously, ensure the digital supply comes up
first.
3. Negate RESET_BAR (HIGH) to bring up the
sensor.
Hard Reset
Assert (LOW) RESET_BAR, it is not necessary to clock
the device. All registers return to the factory defaults. When
the pin is negated (HIGH), the chip resumes normal
operation.
Soft Reset
Set the Reset register field to “1” (R0x0D[0] = 1). All
registers except the following will be reset:
• Chip_Enable
• Synchronize_Changes
• Reset
• Use_PLL
• Power_PLL
• PLL_m_Factor
• PLL_n_Divider
• PLL_p1_Divider
When powering down, be sure to follow this sequence to
ensure that I/Os do not load any buses that they are
connected to.
1. Assert RESET_BAR.
2. Remove the supplies.
Clocks
The MT9P031 requires one clock (EXTCLK), which is
nominally 96 MHz. By default, this results in pixels being
output on the DOUT pins at a maximum data rate of 96 Mp/s.
With VDD_IO = 1.8 V, maximum master clock and
maximum data rate become 48 MHz and 48 Mp/s,
respectively. The EXTCLK clock can be divided down
internally by setting Divide_Pixel_Clock to a non−zero
value. This slows down the operation of the chip as though
EXTCLK had been divided externally.
When the field is returned to “0,” the chip resumes normal
operation.
fEXTCLK
fPIXCLK=
if Divide_Pixel_Clock = 0
{
fEXTCLK
/ (2 × Divide_Pixel_Clock)
otherwise
output, and another divider stage to generate the output
clock. The clocking structure is shown in Figure 13. PLL
control registers can be programmed to generate desired
master clock frequency.
NOTE: The PLL control registers must be programmed
while the sensor is in the software Standby state.
The effect of programming the PLL divisors
while the sensor is in the streaming state is
undefined.
The DOUT, LV, FV, and STROBE outputs are launched on
the rising edge of PIXCLK, and should be captured on the
falling edge of PIXCLK. The specific relationship of
PIXCLK to these other outputs can be adjusted in two ways.
If Invert_Pixel_Clock is set, the sense of PIXCLK is
inverted from that shown in Figure 8. In addition, if the pixel
clock has been divided by Divide_Pixel_Clock, it can be
shifted relative to the other outputs by setting
Shift_Pixel_Clock.
PLL-Generated Master Clock
The PLL contains a prescaler to divide the input clock
applied on EXTCLK, a VCO to multiply the prescaler
PLL Output Clock
PLL Input Clock
EXTCLK
Pre PLL
Div
PFD
PLL
Multiplier
(VCO)
N
PLL_n_divider +1
PLL
Output
Div 1
M
PLL_m_factor
P1
PLL_p1_divider +1
Figure 13. PLL-Generated Master Clock
www.onsemi.com
13
SYSCLK (PIXCLK)
MT9P031
PLL Setup
REG= 0x07, 0x1F82
REG= 0x07, 0x1F80
REG= 0x0B, 0x0001
The MT9P031 has a PLL which can be used to generate
the pixel clock internally.
To use the PLL:
1. Bring the MT9P031 up as normal, make sure that
fEXTCLK is between 6 and 27 MHz and then
power on the PLL by setting Power_PLL
(R0x10[0] = 1).
2. Set PLL_m_Factor, PLL_n_Divider, and
PLL_p1_Divider based on the desired input
(fEXTCLK) and output (fPIXCLK) frequencies.
Determine the M, N, and P1 values to achieve the
desired fPIXCLK using this formula:
Leaving Soft Standby
REG= 0x0B, 0x0002
REG= 0x0B, 0x0003
REG= 0x07, 0x1F80
REG= 0x07, 0x1F82
REG= 0x0B, 0x0001
For maximum power savings in standby mode, EXTCLK
should not be toggling.
When standby mode is entered, either by clearing
Chip_Enable or by asserting STANDBY_BAR, the PLL is
disabled automatically or powered down. It must be
manually re-enabled when leaving standby as needed.
fPIXCLK = (fEXTCLK × M) / (N × P1)
where
M = PLL_m_Factor
N = PLL_n_Divider + 1
P1 = PLL_p1_Divider + 1
2 MHz < fEXTCLK / N < 13.5 MHz
180 MHz < (fEXTCLK × M) / N < 360 MHz
Full-Array Readout
The entire array, including dark pixels, can be read out
without digital processing or automatic black level
adjustments. This can be accomplished as follows:
1. Set Row_Start and Column_Start to 0.
2. Set Row_Size to 2003.
3. Set Column_Size to 2751.
4. Set Manual_BLC to 1.
5. Set Row_BLC to 0.
6. Set Row_Black_Default_Offset to 0.
7. Set Show_Dark_Rows and Show_Dark_Columns
to 0.
NOTE: If P1 is odd (that is, PLL_p1_Divider is even),
the duty cycle of the internal system clock will
not be 50:50. In this case, it is important that
either a slower clock is used or all clock enable
bits are set in R101.
It is desirable to keep (fEXTCLK / n) as large as
possible within the limits. Also, ”m” must be
between 16 and 255, inclusive.
3. Wait 1ms to ensure that the VCO has locked.
4. Set Use_PLL (R0x10[1] = 1) to switch from
EXTCLK to the PLL-generated clock.
If automatic analog (coarse) BLC is desired, but no digital
processing, modify the above settings as follows:
1. Set Row_Start to 12.
2. Set Row_Size to 1993.
3. Set Manual_BLC to 0.
Standby and Chip Enable
The MT9P031 can be put in a low-power Standby state by
either method below:
1. Hard Standby: By pulling STANDBY_BAR LOW,
or
2. Soft Standby: By clearing the Chip_Enable
register field (R0x07[1] = 0).
These settings result in the same array layout as above, but
only 22 dark rows are available at the top of the array; the
first eight are used in the black level algorithm, and there
should be a two-row buffer between the black region and the
active region.
When the sensor is put in standby, all internal clocks are
gated, and analog circuitry is put in a state that it draws
minimal power. The two wire serial interface is still active.
If the sensor was in continuous mode when put in standby,
it resumes from where it was when standby was deactivated.
Naturally, this frame and the next frame are corrupted,
though the sensor itself does not realize this. As this could
affect automatic black level calibration, it is recommended
that either the chip be paused (by setting Restart_Pause)
before being put in standby mode, or it be restarted (setting
Restart) upon resumption of operation.
Window Control
The output image window of the pixel (the FOV) is
defined by four register fields. Column_Start and Row_Start
define the X and Y coordinates of the upper-left corner of the
FOV. Column_Size defines the width of the FOV, and
Row_Size defines the height of the FOV in array pixels.
The Column_Start and Row_Start fields must be set to an
even number. The Column_Size and Row_Size fields must
be set to odd numbers (resulting in an even size for the FOV).
The Row_Start register should be set no lower than 12 if
either Manual_BLC is clear or Show_Dark_Rows is set.
If no special resolution modes are set (see below), the
width of the output image, W, is Column_Size + 1 and the
height, H, is Row_Size + 1.
Entering Soft Standby
REG= 0x0B, 0x0002
REG= 0x0B, 0x0003
www.onsemi.com
14
MT9P031
Readout Modes
binning modes are supported. Rows and columns can be
binned independently.
Subsampling
By default, the resolution of the output image is the full
width and height of the FOV as defined in “Window
Control”. The output resolution can be reduced by two
methods: Skipping and Binning.
Row and column skip modes use subsampling to reduce
the output resolution without reducing FOV. The MT9P031
also has row and column binning modes, which can reduce
the impact of aliasing introduced by the use of skip modes.
This is achieved by the averaging of 2 or 3 adjacent rows and
columns (adjacent same-color pixels). Both 2X and 4X
Skipping
Skipping reduces resolution by using only selected pixels
from the FOV in the output image. In skip mode, entire rows
and columns of pixels are not sampled, resulting in a lower
resolution output image. A skip 2X mode skips one Bayer
pair of pixels for every pair output. Skip 3X skips two pairs
for each one pair output. Rows and columns are always read
out in pairs. If skip 2X mode is enabled with otherwise
default sensor settings, the columns in the output image
correspond to the pixel array columns 16, 17, 20, 21, 24,
25... .
LV
Normal readout
DOUT[11:0]
G0
[11:0]
R0
[11:0]
G1
[11:0]
R1
[11:0]
G0
[11:0]
R0
[11:0]
G2
[11:0]
R2
[11:0]
G2
[11:0]
R2
[11:0]
G3
[11:0]
R3
[11:0]
LV
Column skip 2X readout
DOUT[11:0]
Figure 14. Eight Pixels in Normal and Column Skip 2X Readout Modes
Skipping can be enabled separately for rows and columns.
To enable skip mode, set either or both of Row_Skip and
Column_Skip to the number of pixel pairs that should be
skipped for each pair used in the output image. For example,
to set column skip 2X mode, set Column_Skip to “1”.
The size of the output image is reduced by the skip mode
as shown in the following two equations:
W+2
ceil((Column_Size ) 1))ń(2
H+2
ceil((Row_Size ) 1))ń(2
(Column_Skip ) 1)))
(eq. 2)
(Row_Skip ) 1)))
X incrementing
Y incrementing
Y incrementing
X incrementing
Figure 16. Pixel Readout (Column Skip 2X)
Figure 15. Pixel Readout (no skipping)
www.onsemi.com
15
(eq. 1)
MT9P031
X incrementing
Y incrementing
Y incrementing
X incrementing
Figure 18. Pixel Readout
(Column Skip 2X, Row Skip 2X)
Figure 17. Pixel Readout (Row Skip 2X)
Row_Skip settings can be averaged instead by setting
Column_Bin and Row_Bin to the number of neighbor pixels
to be averaged with each output pixel. For example, to set
bin 2X mode, set Column_Skip and Column_Bin to 1.
Additionally, Column_Start must be a multiple of
(2 * (Column_Bin + 1)) and Row_Start must be a multiple
of (2 * (Row_Bin + 1)).
Only certain combinations of binning and skipping are
allowed.
These are shown in Table 12. If an illegal skip value is
selected for a bin mode, a legal value is selected instead.
Binning
Binning reduces resolution by combining adjacent
same-color imager pixels to produce one output pixel. All of
the pixels in the FOV contribute to the output image in bin
mode. This can result in a more pleasing output image with
reduced subsampling artifacts. It also improves low-light
performance. For columns, the combination step can be
either an averaging or summing operation. Depending on
lighting conditions, one or the other may be desirable. In
low-light conditions, summing produces a gain roughly
equivalent to the column bin factor. Column summing may
be enabled by setting Column_Sum.
Binning works in conjunction with skipping. Pixels that
would be skipped because of the Column_Skip and
Table 12. LEGAL VALUES FOR COLUMN_SKIP BASED ON COLUMN_BIN
Column_Bin
Legal Values for Column_Skip
0 (no binning)
0, 1, 2, 3, 4, 5, 6
1 (Bin 2x)
1, 3, 5
3 (Bin 4x)
3
1. Ensure that Column_Start (R0x02) is set in the form shown below, where n is an integer:
no bin
Bin 2x
Bin 4x
Mirror Column = 0
4n
8n
16n
Mirror Column = 1
4n + 2
8n + 4
16n + 8
Bin mode is illustrated in Figure 19 and Figure 20.
www.onsemi.com
16
MT9P031
X incrementing
Y incrementing
Y incrementing
X incrementing
Figure 20. Pixel Readout
(Column Bin 2X, Row Bin 2X)
Figure 19. Pixel Readout (Column Bin 2X)
Mirror
Column Mirror Image
By setting R0x20[14] = 1, the readout order of the
columns is reversed, as shown in Figure 21. The starting
color, thus Bayer pattern, is preserved when mirroring the
columns.
LINE_VALID
Normal readout
DOUT [11:0]
G0
(11:0)
R0
(11:0)
G1
(11:0)
R1
(11:0)
G2
(11:0)
R2
(11:0)
R2
(11:0)
G2
(11:0)
R1
(11:0)
G1
(11:0)
R0
(11:0)
G0
(11:0)
Reverse readout
DOUT[11:0]
Figure 21. Six Pixels in Normal and Column Mirror Readout Modes
Row Mirror Image
By setting R0x20[15] = 1, the readout order of the rows is
reversed as shown in Figure 22. The starting color, thus
Bayer pattern, is preserved when mirroring the rows.
FRAME_VALID
Normal readout
DOUT[11:0]
Row0
(11:0)
Row1
(11:0)
Row2
(11:0)
Row3
(11:0)
Row4
(11:0)
Row5
(11:0)
Row5
(11:0)
Row4
(11:0)
Row3
(11:0)
Row2
(11:0)
Row1
(11:0)
Row0
(11:0)
Reverse readout
DOUT[11:0]
Figure 22. Six Rows in Normal and Row Mirror Readout Modes
By default, active pixels in the resulting image are output
in row-major order (an entire row is output before the next
row is begun), from lowest row/column number to highest.
If desired, the output (and sampling) order of the rows and
columns can be reversed. This affects only pixels in the
active region defined above, not any pixels read out as dark
rows or dark columns. When the readout direction is
reversed, the color order is reversed as well (red, green, red,
and so on, instead of green, red, green, and so on, for
example).
www.onsemi.com
17
MT9P031
As a special case, in Snapshot modes (see “Operating
Modes”), register writes that occur after FV but before the
next trigger will take effect immediately on the next frame,
as if there had been a Restart. However, if the trigger for the
next frame in ERS Snapshot mode occurs during FV, register
writes take effect as with continuous mode.
Additional control over the timing of register updates can
be achieved by using synchronize_changes. If this bit is set,
writes to certain register fields that affect the brightness of
the output image do not take effect immediately. Instead, the
new
value
is
remembered
internally.
When
synchronize_changes is cleared, all the updates
simultaneously take effect on the next frame (as if they had
all been written the instant synchronize_changes was
cleared). Register fields affected by this bit are identified in
Table 13 of the register reference.
Fields not identified as being frame−synchronized or
affected by synchronize_changes are updated immediately
after the register write is completed. The effect of these
registers on the next frame can be difficult to predict if they
affect the shutter pointer.
If row binning is combined with row mirroring, the
binning is still done in the positive direction. Therefore, if
the first output row in bin 2X + row mirror was 1997, pixels
on rows 1997 and 1999 would be averaged together. The
next pixel output would be from rows 1996 and 1998,
followed by the average of 1993 and 1995.
For column mirroring plus binning, the span of pixels used
should be the same as with non-mirror mode.
Maintaining a Constant Frame Rate
Maintaining a constant frame rate while continuing to
have the ability to adjust certain parameters is the desired
scenario. This is not always possible, however, because
register updates are synchronized to the read pointer, and the
shutter pointer for a frame is usually active during the
readout of the previous frame. Therefore, any register
changes that could affect the row time or the set of rows
sampled causes the shutter pointer to start over at the
beginning of the next frame.
By default, the following register fields cause a “bubble”
in the output rate (that is, the vertical blank increases for one
frame) if they are written in continuous mode, even if the
new value would not change the resulting frame rate:
• Row_Start
• Row_Size
• Column_Size
• Horizontal_Blank
• Vertical_Blank
• Shutter_Delay
• Mirror_Row
• Row_Bin
• Row_Skip
• Column_Skip
Restart
To restart the MT9P031 at any time during the operation
of the sensor, write a “1” to the restart register (R0x0B[0] =
1). This has two effects: first, the current frame is interrupted
immediately. Second, any writes to frame-synchronized
registers and the shutter width registers take effect
immediately, and a new frame starts (in continuous mode).
Register updates being held by synchronize_changes do not
take effect until that bit is cleared. The current row and one
following row complete before the new frame is started, so
the time between issuing the Restart and the beginning of the
next frame can vary by about tROW.
If Pause_Restart is set, rather than immediately beginning
the next frame after a restart in continuous mode, the sensor
pauses at the beginning of the next frame until Pause_Restart
is cleared. This can be used to achieve a deterministic time
period from clearing the Pause_Restart bit to the beginning
of the first frame, meaning that the controller does not need
to be tightly synchronized to LV or FV.
NOTE: When Pause_Restart is cleared, be sure to leave
Restart set to “1” for proper operation. The
Restart bit will be cleared automatically by the
device.
The size of this bubble is (SW × tROW), calculating the
row time according to the new settings.
The Shutter_Width_Lower and Shutter_Width_Upper
fields may be written without causing a bubble in the output
rate under certain circumstances. Because the shutter
sequence for the next frame often is active during the output
of the current frame, this would not be possible without
special provisions in the hardware. Writes to these registers
take effect two frames after the frame they are written, which
allows the shutter width to increase without interrupting the
output or producing a corrupt frame (as long as the change
in shutter width does not affect the frame time).
Image Acquisition Modes
The MT9P031 supports two image acquisition modes
(Shutter Types) (see “Operating Modes”), electronic rolling
shutter and global reset release.
Synchronizing Register Writes to Frame Boundaries
Changes to most register fields that affect the size or
brightness of an image take effect on the frame after the one
during which they are written. These fields are noted as
“synchronized to frame boundaries” in Table 12 of the
register reference. To ensure that a register update takes
effect on the next frame, the write operation must be
completed after the leading edge of FV and before the
trailing edge of FV.
Electronic Rolling Shutter
The ERS modes take pictures by scanning the rows of the
sensor twice in the order described in “Full-Array Readout”.
On the first scan, each row is released from reset, starting the
exposure. On the second scan, the row is sampled,
processed, and returned to the reset state. The exposure for
www.onsemi.com
18
MT9P031
SDmax = 1232; if SW < 3
1504, otherwise
any row is therefore the time between the first and second
scans. Each row is exposed for the same duration, but at
slightly different point in time, which can cause a shear in
moving subjects.
Whenever the mode is changed to an ERS mode (even
from another ERS mode), and before the first frame
following reset, there is an anti-blooming sequence where
all rows are placed in reset. This sequence must complete
before continuous readout begins. This delay is:
tALLRESET = 16 × 2004 × tACLK
The exposure time is calculated by determining the reset
time of each pixel row (with time 0 being the start of the first
row time), and subtracting it from the sample time. Under
normal conditions in ERS modes, every pixel should end up
with the same exposure time. In global shutter release
modes, or in row binning modes, the exposure times of
individual pixels can vary.
In global shutter release modes (described later) exposure
time starts simultaneously for all rows, but still ends as
defined above. In a real system, the exposure would be
stopped by a mechanical shutter, which would effectively
stop the exposure to all rows simultaneously. Because this
specification does not consider the effect of an external
shutter, each output row’s exposure time will differ by
tROW from the previous row.
Global shutter modes also introduce a constant added to
the shutter time for each row, because the exposure starts
during the global shutter sequence, and not during any row’s
shutter sequence. For each additional row in a row bin, this
offset will increase by the length of the shutter sequence.
In Bulb_Exposure modes (see details in Table 13), the
exposure time is determined by the width of the TRIGGER
pulse rather than the shutter width registers. In ERS bulb
mode, it is still a multiple of row times, and the shutter
overhead equation still applies. In GRR bulb mode, the
exposure time is granular to ACLKs, and shutter overhead
(and thus shutter_delay) has no effect.
Global Reset Release
The GRR modes attempt to address the shearing effect by
starting all rows’ exposures at the same time. Instead of the
first scan used in ERS mode, the reset to each row is released
simultaneously. The second scan occurs as normal, so the
exposure time for each row would different. Typically, an
external mechanical shutter would be used to stop the
exposure of all rows simultaneously.
In GRR modes, there is a startup overhead before each
frame as all rows are initially placed in the reset state
(tALLRESET). Unlike ERS mode, this delay always occurs
before each frame. However, it occurs as soon as possible
after the preceding frame, so typically the time from trigger
to the start of exposure does not include this delay. To ensure
that this is the case, the first trigger must occur no sooner
than tALLRESET after the previous frame is read out.
Exposure
The nominal exposure time, tEXP, is the effective shutter
time in ERS modes, and is defined by the shutter width, SW,
and the shutter overhead, SO, which includes the effect of
Shutter_Delay. Exposure time for other modes is defined
relative to this time. Increasing Shutter_Delay (SD)
decreases the exposure time. Exposure times are typically
specified in units of row time, although it is possible to
fine-tune exposures in units of tACLKs (where tACLK is 2
* tPIXCLK).
tEXP = SW × tROW – SO × 2 × tPIXCLK
where:
SW = max(1, (2 * 16 × Shutter_Width_Upper) +
Shutter_Width_Lower)
SO = 208 × (Row_Bin + 1) + 98 + min(SD, SDmax) – 94
SD = Shutter_Delay + 1
Operating Modes
In the default operating mode, the MT9P031 continuously
samples and outputs frames. It can be put in “snapshot” or
triggered mode by setting snapshot, which means that it
samples and outputs a frame only when triggered. To leave
snapshot mode, it is necessary to first clear Snapshot then
issue a restart.
When in snapshot mode, the sensor can use the ERS or the
GRR. The exposure can be controlled as normal, with the
shutter_width_lower and shutter_width_upper registers, or
it can be controlled using the external TRIGGER signal. The
various operating modes are summarized in Table 13.
Table 13. OPERATING MODE
Mode
Settings
Description
ERS Continuous
Default
Frames are output continuously at the frame rate defined by tFRAME. ERS is
used, and the exposure time is electronically controlled to be tEXP.
ERS Snapshot
Snapshot = 1
Frames are output one at a time, with each frame initiated by a trigger. ERS is
used, and the exposure time is electronically controlled to be tEXP.
ERS Bulb
Snapshot = 1;
Bulb_Exposure = 1
Frames are output one at a time, with each frame’s exposure initiated by a trigger.
ERS is used. End of exposure and readout are initiated by a second trigger.
www.onsemi.com
19
MT9P031
Table 13. OPERATING MODE (continued)
Mode
Settings
Description
GRR Snapshot
Snapshot = 1;
Global_Reset = 1
Frames are output one at a time, with each frame initiated by a trigger. GRR is
used. Readout is electronically triggered based on SW.
GRR Bulb
Snapshot = 1;
Bulb_Exposure = 1;
Global_Reset = 1
Frames are output one at a time, with each frame initiated by a trigger. GRR is
used. Readout is initiated by a second trigger.
1. In ERS bulb mode, SW must be greater than 4 (use trigger wider than tROW * 4).
Invert_Trigger is set, the second trigger is a low level on
TRIGGER (or a Restart). In bulb modes, the minimum
possible exposure time depends on the mechanical shutter
used.
After one frame has been output, the chip will reset step
1, above, eventually waiting for the first trigger again. The
next trigger may be issued after ((VB - 8) x tROW) in ERS
modes or tALLREST in GRR modes.
The choice of shutter type is made by Global_Reset. If it
is set, the GRR shutter is used; otherwise, ERS is used. The
two shutters are described in “Electronic Rolling Shutter”
and “Global Reset Release”.
The default ERS continuous mode is shown in Figure 8.
Figure 23 shows default signal timing for ERS snapshot
modes, while Figure 24 shows default signal timing for
GRR snapshot modes.
All operating modes share a common set of operations:
1. Wait for the first trigger, then start the exposure.
2. Wait for the second trigger, then start the readout.
The first trigger is by default automatic, producing
continuous images. If snapshot is set, the first trigger can
either be a low level on the TRIGGER pin or writing a “1”
to the trigger register field. If Invert_Trigger is set, the first
trigger is a high level on TRIGGER pin (or a “1” written to
trigger register field). Because TRIGGER is level-sensitive,
multiple frames can be output (with a frame rate of
tFRAME) by holding TRIGGER pin at the triggering level.
The second trigger is also normally automatic, and
generally occurs SW row times after the exposure is started.
If Bulb_Exposure is set, the second trigger can either be a
high level on TRIGGER or a write to Restart. If
TT1
TSW
TT2
TSE
SW xtROW
TRIGGER
8 x tROW
(H + VB) x t ROW
STROBE
FV
LV
DOUT
8 x tROW
tROW
(a) ERS Snapshot
tROW
First Row Exposure
Second Row Exposure
TT1
TSE
TRIGGER
SW x tROW
STROBE
(H + VB) x tROW
TSW TT2
8 x tROW
FV
LV
DOUT
(b) ERS Bulb
8 x tROW
First Row Exposure
tROW
Second Row Exposure
Figure 23. ERS Snapshot Timing
www.onsemi.com
20
tROW
MT9P031
TT1
TRIGGER
TSE
SW x tROW + 2000 x tACLK
TSW
VB x tROW + 2000 xtACLK
STROBE
TT2
8 x tROW
FV
LV
DOUT
tROW
First Row Exposure
(a) GRR Snapshot
Second Row Exposure
TT1
TRIGGER
STROBE
TSE
SW x tROW + 2000 x tACLK
VB xtROW + 2000 xtACLK
TSW TT2
8 x t ROW
FV
LV
DOUT
First Row Exposure
(b) GRR Bulb
tROW
Second Row Exposure
Figure 24. GRR Snapshot Timing
as shown in Figure 23 and Figure 24. Also indicated in these
figures are the leading and trailing edges of STROBE, which
an be configured to occur at one of several timepoints. The
leading edge of STROBE occurs at STROBE_Start, and the
trailing edge at STROBE_End, which are set to codes
described in Table 14.
Strobe Control
To support synchronization of the exposure with external
events such as a flash or mechanical shutter, the MT9P031
produces a STROBE output. By default, this signal is
asserted for approximately the time that all rows are
simultaneously exposing, minus the vertical blanking time,
Table 14. STROBE TIMEPOINTS
Symbol
Timepoint
Code
TT1
Trigger 1 (start of shutter scan)
–
TSE
Start of exposure (all rows simultaneously exposing) offset by VB
1
TSW
End of shutter width (expiration of the internal shutter width counter)
2
TT2
Trigger 2 (start of readout scan)
3
Signal Chain and Datapath
If STROBE_Start and STROBE_End are set to the same
timepoint, the strobe is a tROW wide pulse starting at the
STROBE_Start timepoint. If the settings are such that the
strobe would occur after the trailing edge of FV, the strobe
may be only tACLK wide; however, because there is no
concept of a row at that time. The sense of the STROBE
signal can be inverted by setting Invert_Strobe (R0x1E[5] =
1. To use strobe as a flash in snapshot modes or with
mechanical shutter, set the Strobe_Enable register bit field
R0x1E[4] = 1.
The signal chain and datapath are shown in Figure 25.
Each color is processed independently, including separate
gain and offset settings. Voltages sampled from the pixel
array are first passed through an analog gain stage, which
can produce gain factors between 1 and 8. An analog offset
is then applied, and the signal is sent through a 12-bit
analog-to-digital converter. In the digital space, a digital
gain factor of between 1 and 16 is applied, and then a digital
www.onsemi.com
21
MT9P031
offset of between –2048 and 2047 is added. The resulting
12-bit pixel value is then output on the DOUT[11:0] ports.
The analog offset applied is determined automatically by
the black level calibration algorithm, which attempts to shift
the output of the analog signal chain so that black is at a
particular level. The digital offset is a fine-tuning of the
analog offset.
Analog Signal Chain
Analog
Gain
Pixel
X
Voltage
Digital Datapath
Analog
Offset
+
Digital
Offset
Correction
Black
Level
Calibration
ADC
X
+
DOUT[11:0]
Digital
Gain
Figure 25. Signal path
possible. The recommended gain settings are shown in
Table 15.
Gain
There are two types of gain supported: analog gain and
digital gain. Combined, gains of between 1 and 128 are
Table 15. GAIN INCREMENT SETTINGS
Gain Range
Increments
Digital Gain
Analog Multipier
Analog Gain
1– 4
0.125
0
0
8–32
4.25–8
0.25
0
1
17–32
9–128
1
1–120
1
32
1. Analog gain should be maximized before applying digital gain.
2. The recommended minimum gain is 1.38 (0x000B)
3. For optimal sensor performance, when using gain settings <= 4.0, also set reserved register R0x3E = 0x0080 and for gain settings >4.0,
set register R0x003E=0x00C0.
The combined gain for a color C is given by:
GC = AGC x DGC.
Digital Gain
The digital gain is specified independently for each color
channel in steps of 0.125. It is controlled by the register
fields Green1_Digital_Gain, Red_Digital_Gain,
Blue_Digital_Gain, and Green2_Digital_Gain. The digital
gain for a color C is given by:
DGC = 1 + (C_Digital_Gain / 8)
Analog Gain
The analog gain is specified independently for each color
channel. There are two components, the gain and the
multiplier. The gain is specified by Green1_Analog_Gain,
Red_Analog_Gain, Blue_Analog_Gain, and
Green2_Analog_Gain in steps of 0.125. The analog
multiplier is specified by Green1_Analog_Multiplier,
Red_Analog_Multiplier, Blue_Analog_Multiplier, and
Green2_Analog_Multiplier. These combine to form the
analog gain for a given color C as shown in this equation:
AGC = (1 + C_Analog_Multiplier) × (C_Analog_Gain /
8)
The gain component can range from 0 to 7.875 in steps of
0.125, and the multiplier component can be either 0 or 1
(resulting in a multiplier of 1 or 2). However, it is best to keep
the “gain” component between 1 and 4 for the best noise
performance, and use the multiplier for gains between 4 and
8.
Offset
The MT9P031 sensor can apply an offset or shift to the
image data in a number of ways.
An analog offset can be applied on a color-wise basis to
the pixel voltage as it enters the ADC. This makes it possible
to adjust for offset introduced in the pixel sampling and gain
stages to be removed, centering the resulting voltage swing
in the ADC’s range. This offset can be automatically
determined by the sensor using the automatic black level
calibration (BLC) circuit, or it can be set manually by the
user. It is a fairly coarse adjustment, with adjustment step
sizes of 4 to 8 LSBs.
www.onsemi.com
22
MT9P031
Digital offset is also added on a color-wise and line-wise
basis to fine tune the black level of the output image. This
offset is based on an average black level taken from each
row’s dark columns, and is automatically determined by the
digital row-wise black level calibration (RBLC) circuit. If
the RBLC circuit is not used, a user-defined offset can be
applied instead. This offset has a resolution of 1 LSBs.
A digital offset is added on a color-wise basis to account
for channel offsets that can be introduced due to “even” and
“odd” pixels of the same color going through a slightly
different ADC chain. This offset is automatically
determined based on dark row data, but it can also be
manually set.
Digital Black Level Calibration
Digital black level calibration is the final calculation
applied to pixel data before it is output. It provides a precise
black level to complement the coarser-grained analog black
level calibration, and also corrects for black level shift
introduced by digital gain. This correction applies to the
active columns for all rows, including dark rows.
Test Patterns
The MT9P031 has the capability of injecting a number of
test patterns into the top of the datapath to debug the digital
logic. With one of the test patterns activated, any of the
datapath functions can be enabled to exercise it in a
deterministic fashion. Test patterns are enabled when
Enable_Test_Pattern is set. Only one of the test patterns can
be enabled at a given point in time by setting the
Test_Pattern_Mode register according to Table 16. When
test patterns are enabled the active area will receive the value
specified by the selected test pattern and the dark pixels will
receive the value in Test_Pattern_Green for green pixels,
Test_Pattern_Blue for blue pixels, and Test_Pattern_Red for
red pixels’+.
NOTE: ON Semiconductor recommends turning off
black level calibration (BLC) when Test Pattern
is enabled, otherwise some of the test patterns
will not be properly output.
Analog Black Level Calibration
The MT9P031 black level calibration circuitry provides
a feedback control system since adjustments to the analog
offset are imprecise by nature. The goal is that within the
dark row region of any supported output image size, the
offset should have been adjusted such that the average black
level falls within the specified target thresholds.
The analog offsets normally need a major adjustment only
when leaving the Reset state or when there has been a change
to a color’s analog gain. Factors like shutter width and
temperature have lower-order impact, and generally only
require a minor adjustment to the analog offsets. The
MT9P031 has various calibration modes to keep the system
stable while still supporting the need for rapid offset
adjustments when necessary.
The two basic steps of black level calibration are:
1. Take a sample.
2. If necessary, adjust the analog offset.
Table 16. TEST PATTERN MODES
Test_Pattern_Mode
Black level calibration is normally done separately for
each color channel, and different channels can use different
sample or adjustment methods at the same time. However,
because both Green1 and Green2 pixels go through the same
signal chain, and Red and Blue pixels likewise go through
the same signal chain, it is expected that the chosen offset for
these pairs should be the same as long as the gains are the
same. If Lock_Green_Calibration is set, and
(Green1_Analog_Gain = Green2_Analog_Gain) and
(Green1_Analog_Multiplier = Green2_Analog_
Multiplier), the calculated or user-specified Green1_Offset
is used for both green channels. Similarly, if
Lock_Red/Blue_Calibration is set, and (Red_Analog_Gain
= Blue_Analog_Gain) and (Red_Analog_Multiplier =
Blue_Analog_Multiplier), the calculated or user-specified
Red_Offset is used for both the red and blue channels.
The current values of the offsets can be read from the
Green1_Offset, Red_Offset, Blue_Offset, and
Green2_Offset registers. Writes to these registers when
Manual_BLC is set change the offsets being used. In
automatic BLC mode, writes to these registers are effective
when manual mode is re-entered. In Manual_BLC mode, no
sampling or adjusting takes place for any color.
Test Pattern Output
0
Color field (normal operation)
1
Horizontal gradient
2
Vertical gradient
3
Diagonal gradient
4
Classic test pattern
5
Walking 1s
6
Monochrome horizontal bars
7
Monochrome vertical bars
8
Vertical color bars
Classic Test Pattern
When selected, a value from Test_Data will be sent
through the digital pipeline instead of sampled data from the
sensor. The value will alternate between Test_Data for even
and odd columns.
Color Field
When selected, the value for each pixel is determined by
its color. Green pixels will receive the value in
Test_Pattern_Green, red pixels will receive the value in
Test_Pattern_Red, and blue pixels will receive the value in
Test_Pattern_Blue.
www.onsemi.com
23
MT9P031
When selected, a walking 1s pattern will be sent through
the digital pipeline. The first value in each row is 1.
Vertical Color Bars
When selected, a typical color bar pattern will be sent
through the digital pipeline.
Monochrome Vertical Bars
When selected, vertical monochrome bars will be sent
through the digital pipeline. The width of each bar can be set
in Test_Pattern_Bar_Width and the intensity of each bar is
set by Test_Pattern_Green for even bars and
Test_Pattern_Blue for odd bars.
Horizontal Gradient
When selected, a horizontal gradient will be produced
based on a counter which increments on every active pixel.
Vertical Gradient
When selected, a vertical gradient will be produced based
on a counter which increments on every active row.
Monochrome Horizontal Bars
When selected, horizontal monochrome bars will be sent
through the digital pipeline. The width of each bar can be set
in Test_Pattern_Bar_Width and the intensity of each bar is
set by Test_Pattern_Green for even bars and
Test_Pattern_Blue for odd bars.
Diagonal Gradient
When selected, a diagonal gradient will be produced
based on the counter used by the horizontal and vertical
gradients.
Walking 1s
www.onsemi.com
24
MT9P031
SPECTRAL CHARACTERISTICS
70
60
QE (%)
50
40
R
30
Gr
20
Gb
10
B
0
350
450
550
650
750
850
1050
950
Wavelength (nm)
Figure 26. Typical Spectral Characteristics
Image Height
CRA vs. Image Height Plot
CRA Design
14
12
CRA (deg)
10
8
6
4
2
0
0
10
20
30
40
50
60
70
Image He ight (%)
80
Figure 27. CRA vs. Image Height (7 deg)
www.onsemi.com
25
90
100
110
(%)
(mm)
CRA
(deg)
0
0
0
5
0.178
0.35
10
0.356
0.70
15
0.535
1.05
20
0.713
1.40
25
0.891
1.75
30
1.069
2.10
35
1.247
2.45
40
1.426
2.80
45
1.604
3.15
50
1.782
3.50
55
1.960
3.85
60
2.138
4.20
65
2.317
4.55
70
2.495
4.90
75
2.673
5.25
80
2.851
5.60
85
3.029
5.95
90
3.208
6.30
95
3.386
6.65
100
3.564
7.00
MT9P031
ELECTRICAL SPECIFICATIONS
Two-Wire Serial Register Interface
The electrical characteristics of the two-wire serial
register interface (SCLK, SDATA) are shown in Figure 28
and Table 17.
tr_clk
t
SCLK
t SDH tSDS
t
SCLK
SRTH
SDATA
Write Address
Bit 7
tf_sdat
90%
90%
10%
10%
tAHSW
tSHAW
t
Register Address
Bit 7
Write Address
Bit 0
Write Start
STPS tSTPH
Register Value
Bit 0
ACK
t
SHAR
SCLK
SDATA
tr_sdat
tf_clk
Read Address
tAHSR
Read Start
t
t
SDHR SDSR
Register Value
Bit 7
Read Address
Bit 0
Bit 7
Stop
Register Value
Bit 0
ACK
Figure 28. Two-Wire Serial Bus Timing Parameters
Notes:
Read sequence: For an 8-bit READ, read waveforms start after WRITE command and register address are issued.
Table 17. TWO-WIRE SERIAL BUS CHARACTERISTICS
Symbol
fSCLK
tSCLK
Definition
Condition
Min
Typ
Max
Unit
Serial interface input clock frequency
–
–
–
400
kHz
Serial Input clock period
–
–
–
2.5
msec
SCLK duty cycle
–
40
50
60
%
tr_sclk
SCLK rise time
–
34
–
ns
tf_sclk
SCLK fall time
–
8
–
ns
tr_sdat
SDATA rise time
–
34
–
ns
tf_sdat
SDATA fall time
–
10
–
ns
tSRTH
Start hold time
WRITE/READ
0
10
28
ns
tSDH
SDATA hold
WRITE
0
0
0
ns
tSDS
SDATA setup
WRITE
0
19.9
59.9
ns
tSHAW
SDATA hold to ACK
WRITE
279
281
300
ns
tAHSW
ACK hold to SDATA
WRITE
279
281
300
ns
tSTPS
Stop setup time
WRITE/READ
0
0
0
ns
tSTPH
Stop hold time
WRITE/READ
0
0
0
ns
tSHAR
SDATA hold to ACK
READ
279
284
300
ns
tAHSR
ACK hold to SDATA
READ
279
284
300
ns
tSDHR
SDATA hold
READ
0
0
0
ns
www.onsemi.com
26
MT9P031
Table 17. TWO-WIRE SERIAL BUS CHARACTERISTICS (continued)
Symbol
Definition
Condition
Min
Typ
Max
Unit
READ
0
19.9
59.9
ns
tSDSR
SDATA setup
CIN_SI
Serial interface input pin capacitance
–
–
3.5
–
pF
CLOAD_SD
SDATA max load capacitance
–
–
15
–
pF
RSD
SDATA pull-up resistor
–
–
1.5
–
kΩ
I/O Timing
See Figure 29 and Table 18 for I/O timing (AC)
characteristics.
By default, the MT9P031 launches pixel data, FV and LV
with the rising edge of PIXCLK. The expectation is that the
user captures DOUT[11:0], FV and LV using the falling edge
of PIXCLK.
tR
tRP
tF
tFP
90 %
90 %
10 %
10 %
tEXTCLK
EXTCLK
tCP
PIXCLK
tPD
tPD
Pxl _ 0
Data[7:0]
Pxl _ 1
Pxl _ 2
Pxl _ n
tPFH
tPLH
FRAME_VALID/
LINE_VALID
tPF
tPL
FRAME_VALID leads LINE_VALID by 609 PIXCLKs.
FRAME_VALID trails
LINE_VALID by 16 PIXCLKs.
*PLL disabled for t CP
Figure 29. I/O Timing Diagram
Table 18. I/O TIMING CHARACTERISTICS
Symbol
Definition
Condition
Min
Typ
Max
Unit
PLL enabled
6
–
27
MHz
Input clock period
PLL enabled
166
–
37
ns
Input clock frequency
PLL disabled
6
–
96
MHz
tEXTCLK2
Input clock period
PLL disabled
125
–
10.4
ns
tR
Input clock rise time
0.03
–
1
V/ns
tF
Input clock fall time
0.03
–
1
V/ns
tRP
Pixclk rise time
0.03
–
1
V/ns
tFP
Pixclk fall time
0.03
–
1
V/ns
Clock duty cycle
40
50
60
%
Jitter on PIXCLK
–
–
1.03
ns
tJITTER1
Input clock jitter 48 MHz
–
300
–
ps
tJITTER2
Input clock jitter 96 MHz
–
220
–
ps
tCP
EXTCLK to PIXCLK propagation delay
Nominal voltages
11.5
17.7
19.1
ns
fPIXCLK
PIXCLK frequency
Default
6
–
96
MHz
tPD
PIXCLK to data valid
Default
0.8
2.1
3.9
ns
tPFH
PIXCLK to FV HIGH
Default
2.8
4.3
5.9
ns
fEXTCLK1
Input clock frequency
tEXTCLK1
fEXTCLK2
t(PIX
JITTER)
www.onsemi.com
27
MT9P031
Table 18. I/O TIMING CHARACTERISTICS
Symbol
Definition
Condition
Min
Typ
Max
Unit
tPLH
PIXCLK to LV HIGH
Default
2.2
3.5
5.9
ns
tPFL
PIXCLK to FV LOW
Default
2.4
4.2
5.9
ns
tPLL
PIXCLK to LV LOW
Default
2.6
4.1
5.9
ns
CLOAD
Output load capacitance
–
<10
–
pF
CIN
Input pin capacitance
–
2.5
–
pF
www.onsemi.com
28
MT9P031
DC ELECTRICAL CHARACTERISTICS
The DC electrical characteristics are shown in Table 19,
Table 20 and Table 21.
Table 19. DC ELECTRICAL CHARACTERISTICS
Min
Typ
Max
Unit
VDD
Symbol
Core digital voltage
1.7
1.8
1.9
V
VDD_IO
I/O digital voltage
1.7
1.8/2.8
3.1
V
VAA
Analog voltage
2.6
2.8
3.1
V
VAA_PIX
Pixel supply voltage
2.6
2.8
3.1
V
VDD_PLL
PLL supply voltage
2.6
2.8
3.1
V
VIH
Input HIGH voltage
2
–
3.3
V
VDD_IO = 1.8 V
1.3
–
2.3
V
VIL
Input LOW voltage
VDD_IO = 2.8 V
–0.3
–
0.8
V
VDD_IO = 1.8 V
–0.3
–
0.5
V
IIN
Input leakage current
No pull-up resistor;
VIN = VDD_IO or DGND
–
<10
–
μA
VOH
Output HIGH voltage
VDD_IO = 1.8 V
1.3
–
1.82
V
VDD_IO = 2.8 V
2.3
–
–
V
VDD_IO = 2.8 V
0.16
–
0.35
V
VDD_IO = 2.8 V
–
–
0.6
V
VOL
Definition
Output LOW voltage
Condition
VDD_IO = 2.8 V
IOH
Output HIGH current
At specified VOH = VDD_IO − 400 mv
at 1.7 V VDD_IO
8.9
–
22.3
mA
IOL
Output LOW current
At specified VOL = 400mv at 1.7 V VDD_IO
2.6
–
5.1
mA
IOZ
Tri-state output leakage
current
VIN = VDD_IO or GND
–
–
2
μA
IDD1
Digital operating current
Parallel mode 96 MHz full frame
nominal voltage, PLL enabled
–
28
35
mA
IDD_IO1
I/O digital operating current
Parallel mode 96 MHz full frame
nominal voltage, PLL enabled
–
38.6
50
mA
IAA1
Analog operating current
Parallel mode 96 MHz full frame
nominal voltage, PLL enabled
–
72
80
mA
IAA_PIX1
Pixel supply current
Parallel mode 96 MHz full frame
nominal voltage, PLL enabled
–
2.4
6
mA
IDD_PLL1
PLL supply current
Parallel mode 96 MHz full frame
nominal voltage, PLL enabled
–
5
6
mA
IDD2
Digital operating current
Parallel mode 96 MHz 4X binning
nominal voltage, PLL enabled
–
15
35
mA
IDD_IO2
I/O digital operating current
Parallel mode 96 MHz 4X binning
nominal voltage, PLL enabled
–
6.4
50
mA
IAA2
Analog operating current
Parallel mode 96 MHz 4X binning
nominal voltage, PLL enabled
–
69
80
mA
IAA_PIX2
Pixel supply current
Parallel mode 96 MHz 4X binning
nominal voltage, PLL Enabled
–
3.4
6
mA
IDD_PLL2
PLL supply current
Parallel mode 96 MHz 4X binning
nominal voltage, PLL enabled
–
5
6
mA
ISTBY1
Hard standby current PLL
enabled
EXTCLK enabled
–
<500
–
μA
ISTBY2
Hard standby current PLL
disabled
EXTCLK disabled
–
<50
–
μA
www.onsemi.com
29
MT9P031
Table 19. DC ELECTRICAL CHARACTERISTICS (continued)
Symbol
Definition
Condition
Min
Typ
Max
Unit
ISTBY3
Soft standby current PLL
enabled
EXTCLK enabled (PLL enabled)
–
<500
–
μA
ISTBY4
Soft standby current PLL
disabled
EXTCLK enabled (PLL disabled)
–
<500
–
μA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
Table 20. POWER CONSUMPTION
Mode
Full Resolution (14 fps)
4X Binning
Unit
Streaming
381
262
mW
CAUTION: Stresses greater than those listed in Table 21 may
cause permanent damage to the device. This is a stress
rating only, and functional operation of the device at
these or any other conditions above those indicated in
the operational sections of this specification is not
implied.
Table 21. ABSOLUTE MAXIMUM RATINGS
Symbol
Definition
Condition
Min
Max
Unit
VDD_MAX
Core digital voltage
–0.3
1.9
V
VDD_IO_MAX
I/O digital voltage
–0.3
3.1
V
VAA_MAX
Analog voltage
–0.3
3.1
V
VAA_PIX_MAX
Pixel supply voltage
–0.3
3.1
V
VDD_PLL_MAX
PLL supply voltage
–0.3
3.1
V
VIN_MAX
Input voltage
–0.3
3.4
V
IDD_MAX
Digital operating current
–
35
mA
IDD_IO_MAX
I/O digital operating current
–
100
mA
IAA_MAX
Analog operating current
–
95
mA
IAA_PIX_MAX
Pixel supply current
–
6
mA
IDD_PLL_MAX
PLL supply current
–
6
mA
TOP
Operating temperature
–30
70
°C
TST
Storage temperature
–40
125
°C
Measure at junction
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. To keep dark current and shot noise artifacts from impacting image quality, care should be taken to keep TOP at a minimum.
www.onsemi.com
30
MT9P031
ILCC48 10x10
CASE 847AA
ISSUE O
www.onsemi.com
31
MT9P031
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
32
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MT9P031/D
Similar pages