Rohm CSL0901VT Lens type led Datasheet

CSL0901 Series
Data Sheet
lFeatures
lOutline
• Lens Type LED
• High Brightnes LED
lSize
1006
(0402)
1608
(0603)
1.6×0.8mm
(t=1.24mm)
1.0×0.6mm
(t=0.2mm)
Color
Type
V
U
D
Y
W
M
P
lRecommended Solder Pattern
lDimensions
Tolerance : 0.1
(unit : mm)
(unit : mm)
lSpecifications
Part No.
Emitting
Chip
Structure
Color
Absolute Maximum Ratings (Ta=25ºC)
Peak Forward Reverse
Operating Temp. Storage Temp.
Dissipation Current
Current Voltage
PD(mW) IF(mA) IFP(mA) VR(V)
Topr(ºC)
Tstg(ºC)
Power Forward
Electrical and Optical Characteristics (Ta=25ºC)
Forward Voltag VF Reverse Current IR
Typ.
(V)
IF
Max.
(mA) (mA)
VR
(V)
Dominant Wavelength lD Luminous Intensity IV
IF
Min. Typ.
Min.*2 Typ. Max.*2 IF
(nm) (nm) (nm) (mA) (mcd) (mcd) (mA)
CSL0901VT
630
174
620
185
605
405
Red
CSL0901UT
Orange
CSL0901DT
CSL0901YT
AIGaInP
on GaAs
50
20
100*1
12
-40 to +100 -40 to +100
2.0
20
10
12
-
590
-
20
-
320
20
Yellow
CSL0901WT
587
290
CSL0901MT
Yellowish
Green
571
140
CSL0901PT
Green
560
34
*1 : Duty 1/10, 1kHz *2 : Reference
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
1/6
2016.03 - Rev.B
Data Sheet
CSL0901 Series
lElectrical Characteristics Curves
reference
Fig.1 Forward Current - Forward Voltages
100
FORWARD CURRENT : IF [mA]
Ta=25ºC
10
CSL0901VT
CSL0901UT
CSL0901DT
CSL0901YT
CSL0901WT
CSL0901MT
CSL0901PT
1
1.0
1.5
2.0
2.5
3.0
FORWARD VOLTAGE : VF [V]
Fig.3 Derating
1.5
Ta=25ºC
CSL0901VT
CSL0901UT
CSL0901DT
CSL0901YT
CSL0901WT
CSL0901MT
CSL0901PT
1.0
MAXIMUM FORWARD CURRENT : [mA]
RELATIVE LUMINOUS INTENSITY [a.u.]
Fig.2 Luminous Intensity - Forward Current
0.5
0.0
0
5
10
15
20
30
20
10
CSL0901VT
CSL0901UT
CSL0901DT
CSL0901YT
CSL0901WT
CSL0901MT
CSL0901PT
Rθj-s ··· 636ºC/W
Rθj-a ··· 723ºC/W
TjMax ··· 110ºC
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100110
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
*Cu foil : 1.5mm×25mm t=0.070mm Cathode
PCB:FR4 t=1.6mm
*This data is actual value from specific lot and is not guaranteed
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
2/6
2016.03 - Rev.B
Data Sheet
CSL0901 Series
lViewing Angle
reference
SCANNING ANGLE (deg)
SCANNING ANGLE (deg)
X-Y
X’ - Y’
30°
20°
10°
0°
10°
30°
40°
Scanning
Direction
Scanning
Direction
20°
40°
50°
50°
90°
100
50
0
50
0°
10°
20°
30°
40°
50°
60°
70°
70°
80°
80°
80°
80°
10°
60°
70°
70°
20°
50°
60°
60°
30°
40°
90°
100
90°
100
RELATIVE INTENSITY
50
0
50
90°
100
RELATIVE INTENSITY
lPart No. Construction
lPacking Specification
ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags.
Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card
inside the bag is available upon request.
Please contact the nearest sales office or distributer if necessary.
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
3/6
2016.03 - Rev.B
CSL0901 Series
Data Sheet
lPrecaution (Surface Mount Device)
1.Storage
If the product is heated during the reflow under the condition of hygroscopic state, it may vaporize and expand
which will influence the performance of the product. Therefore, the package is waterproof. Please use the
product following the conditions:
・Using Conditions
Classification
Temperature
Humidity
①Before using
5 to 30ºC
30 to 70%RH
②After opening
package
5 to 30ºC
Below 70%RH
Expiration Date
Remark
Within 1 year
Storage with waterproof package
from Receiving
Within 168h
Please storing in the airtight container with
our desiccant (silica gel)
・Baking
Bake the product in case of below:
①The expiration date is passed.
②The color of indicator (silica gel) turned from blue to colorless or from green to pink. (Even if the product is
within the expiration date.)
・Baking Conditions
Temperature
60±3ºC
Remark
Time
12 to 24h
Humidity
Below 20%RH
・Bake products in reel.
・Reel and embossed tape are easy to be deformed when baking, so please try not to apply
stress on it.
・Recommend bake once.
2.Application Methods
2-1. Precaution for Drive System and Off Mode
Design the circuit without the electric load exceeding the ABSOLUTE MAXIMUM RATING that applies on the
products. If drive by constant voltage, it may cause current deviation of the LED and result in deviation of
luminous intensity, so we recommend to drive by constant current. (Deviation of VF Value will cause deviation of
current in LED.) Furthermore, for off mode, please do not apply voltage neither forward nor reverse. Especially,
for the products with the Ag-paste used in the die bonding, there’
s high possibility to cause electro migration
and result in function failure.
2-2. Operation Life Span
There’
s possibility for intensity of light drop according to working conditions and environments (applied
current, surrounding temperature and humidity, corrosive gases), please call our Sales staffs for inquiries about
the concerned application below.
①Longtime intensity of light life
②On mode all the time
2-3.Applied Stress on Product
The top of the LED is very soft, which the silicon resin is used as sealing resin. Therefore, please pay attention
to the overstress on it which may influence its reliability.
2-4.Usage
The Product is LED. We are not responsible for the usage as the diode such as Protection Chip, Rectifier,
Switching and so on.
3. Others
3-1. Surrounding Gas
Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas (ammonia), it
may result in low soldering ability (caused by the change in quality of the plating surface ) or optical
characteristics changes (light intensity, chrominance) and change in quality of die bonding (Ag-paste) materials.
All of the above will cause function failure of the products.
Therefore, please pay attention to the storage environment for mounted product (concern the generated gas of
the surrounding parts of the products and the atmospheric environment).
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
4/6
2016.03 - Rev.B
CSL0901 Series
Data Sheet
3-2. Electrostatic Damage
The product is part of semiconductor and electrostatic sensitive, there’
s high possibility to be damaged by the
electrostatic discharge. Please take appropriate measures to avoid the static electricity from human body and
earthing of production equipment. The resistance values of electrostatic discharge (actual values) vary with
products, therefore, please call our Sales staffs for inquiries.
3-3. Electromagnetic Wave
Please concern the influence on LED in case of application with strong electromagnetic wave such as IH
(Induction heating).
4.Mounting
4-1. Soldering
・No resin hardening agent such as filler is used in the sealing resin of the product. Therefore, resin expansion
and
moisture absorption at humidity will cause heat stress during soldering process and finally has bad influence
on the product’s reliability.
・The product is not for flow soldering.
・Do not expose the product in the environment of high temperature (over 100ºC ) or rapid temperature shift
(within 3ºC of temperature gradient) during the flow soldering of surrounding parts.
・Please set appropriate reflow temperature based on our product usage conditions and specification.
・The max for reflowing is 2 times, please finish the second flow soldering and flow soldering with other parts
within the usage limitation after open the moistureproof package.
・Compare with N2 reflow, during air reflow, because of the heat and surrounding conditions, it may cause the
discoloration of the resin.
・For our product that has no solder resist, because of its solder amount and soldering conditions, one of its
specific characteristics is that solder will penetrate into LED. Thus, there's high possibility that will influence its
reliability. Therefore, please be informed, concerning it before using it.
4-2. Automatic Mounting
4-2-1.Silicon Resin Sealing Product
The sealing resin of LED is very soft, so please select adsorption nozzle that would not apply stress directly on
the sealing section.
4-2-2.Mini Package (Smaller than 1608 size)
Vibration may result in low mounting rate since it will cause the static electricity of product and adhere to top
cover tape. We recommend to
・set magnet on parts feeder cassette of the mounter to control the product stabilization
・set ionizer to prevent electrostatic charge
4-3. Mounting Location
The stress like bending stress of circuit board dividing after mounting, may cause LED package crack or
damage of LED internal junction, therefore, please concern the mounting direction and position to avoid bending
or screwing with great stress of the circuit board..
4-4. Mechanical Stress after Mounting
The mechanical stress may damage the LED after Circuit Mounting, so please pay attention to the touch on
product.
Stress strength according to
the mounting position:
A>B>C>D
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
5/6
2016.03 - Rev.B
CSL0901 Series
Data Sheet
4-5. Soldering Pattern for Recommendation
We recommend the soldering pattern that shows on the right. It will be
different according to mounting situation of circuit board, therefore,
please concern before designing.
※The product has adopted the electrode structure that it should solder
with back electrode of the product. Thus, please be informed that the
shape of electrode pin of solder fillet formation is not guaranteed.
4-6. Reflow Profile
For reflow profile, please refer to the conditions below:(※)
0.8mm
0.8m
m
0.85m
m
0.8m
Direction for Circuit Board Warping
m
・Meaning of marks, Conditions
Mark
Meanings
Tsmax
Maximum of pre-heating temperature
Tsmin
Minimum of pre-heating temperature
ts
Time from Tsmin to Tsmax
TL
Reference temperature
tL
Retention time for TL
TP
Peak temperature
tP
Time for peak temperature
ΔTR/Δt
Temperature rising rate
ΔTD/Δt
Temperature decreasing rate
Conditions
180ºC
140ºC
Over 60sec.
230 to 260ºC
Within 40sec.
260ºC(Max)
Within 10sec.
Under 3ºC/sec.
Over -3ºC/sec.
※Above conditions are for reference. Therefore, evaluate by customer’s own circuit boards and reflow
furnaces before using, because stress from circuit boards and temperature variations of reflow furnaces vary
by customer’
s own conditions.
4-7. Cleaning after Soldering
Please follow the conditions below if the cleaning is necessary after soldering.
Solvent
Temperature
Ultrasonic Cleaning
Drying
We recommend to use alcohols solvent such as, isopropyl alcohols
Under 30ºC within 3 minutes
15W/Below 1 liter (capacity of tank)
Under 100ºC within 3 minutes
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
6/6
2016.03 - Rev.B
Notice
Notes
1) The information contained herein is subject to change without notice.
2) Before you use our Products, please contact our sales representative and verify the latest specifications :
3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.
4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.
5) The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.
6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in
this document.
7) The Products specified in this document are not designed to be radiation tolerant.
8) For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.
9) Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.
10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.
11) ROHM has used reasonable care to ensur the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.
12) Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.
13) When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.
14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
R1102A
Datasheet
CSL0901DT - Web Page
Part Number
Package
Unit Quantity
Minimum Package Quantity
Packing Type
Constitution Materials List
RoHS
CSL0901DT
CSL0901
inquiry
Yes
Similar pages