7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER 4 3 2 20 REVISION DESCRIPTION A 2151590 -2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 5 FINE CRIMP HEIGHT ADJUST A 2151590 -5 SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 12 A NON-CRIMP HEIGHT ADJUST 2151590 -7 A FINE CRIMP HEIGHT ADJUST A PNEUMATIC FEED SERVO LATCH PLATE 2151590 -6 7- 2151590 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST A APPLICATOR STYLE CONVERSION CHART FEED TYPE 4 NONE CRIMP TOOLING KIT - 4 PNEUMATIC FEED - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 1338685-1 2119951-1 - 2161326-1 - 2119949-1 1338685-1 2119950-1 - - 2119641-1 2119799-1 8- 2151590 -4 - - 8- 2151590 -5 5-18022-5 8- 2151590 -5 8- 2151590 -4 5-18022-5 1338685-1 - - 5-18022-5 5-18022-5 - - - - - 1901094-3 2119653-1 1901094-3 - 2119653-1 2119641-1 - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - (QUANTITY 2) - - - - - 2063440-1 - - - - - - - - - - - - - - - - - - - 6 - - TYPE 2.29 mm [.090] APPLICATOR INSTRUCTIONS 408-10389 - - - TE TERMINAL TERMINAL DATA: MCON-2.8-RECEPTACLE TERMINAL NAME: WIRE STRIP LENGTH 3.20-3.80 mm [.126-.150 IN] C TERMINAL APPLICATION SPECIFICATION n 114-18718 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 1.15-1.40 mm [.045-.055 IN] - - - - - - 6 TERMINALS APPLIED TE TERMINAL 1719836-1 TE TERMINAL 1719836-3 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 0.35mm2 0.22mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.07+/-0.03 [.042+/-.001] 1.00+/-0.03 [.039+/-.001] CRIMP HEIGHT REFERENCE SETTING 8.7 W1__DWG_CRIMP_HT_2 - 9 6.0 W1__DWG_CRIMP_HT_1 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - B 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 7 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 8 9 10 11 A 12 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62 FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 2151590 2151590 2151590 2151590 - -4 -4 -5 -6 - & 242. 1 & 242. & 252. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 - TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF - - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - 1 -77 -7 1 - -6 1 -5 1 -2 1 2119957-2 8-21084-0 -1 PART NO - APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 260 252 ITEM NO 1 1 1 1 DIMENSIONS: mm & 4 of 4) 1 1 1 1 1 1 1 REF 1 1 1 1 2 1 3 1 4 2 1 1 1 - - 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - 1 66 P LTR DESCRIPTION DATE RELEASED - - 1 - - MATERIAL - -1 PART NO - 2 1 1 - - - 1 - - 1 - 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 1 - 1 1 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-8 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 1338685-1 2168400-1 2168083-8 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-1 2119085-1 2119092-1 1752356-3 2079383-5 2161328-1 1320908-3 2119959-1 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 462006-6 1-1633129-7 6-240641-5 2119757-8 238011-4 1633965-4 455888-5 1-456403-3 - - 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 1 1 1 1 -6 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 - 4 2 1 1 1 4 2 1 1 1 4 1 1 1 - 2 3 1 - 4 1 3 1 - 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - - 1 1 2 1 - 1 - - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 -5 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 4.73 . Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - - -77 -7 ATLANTIC VERSION AMP 4805 REV 31MAR2000 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 A DWN APVD CC 22APR2013 TE 2063440-1 F O 1.57 mm [.062] REVISIONS DIST A - APPLICATOR DATA 1 PART NUMBERS REQUIRED - - LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 2151590 -1 D 6 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP, RoHS, M4 X 16 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .062 SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 19FEB2013 CHK 19FEB2013 APVD 19FEB2013 L.ZHANG L.ZHANG S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-8 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 1338685-1 4 2168400-1 2 2168083-8 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 2119085 1 2119092-1 1 1752356-3 2 2079383-5 1 2161328 1 1320908-3 1 2119959-1 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 462006-6 1 1-1633129-7 1 6-240641-5 .. 1 ITEM_6 1 2119757-8 1 238011-4 1 1633965-4 1 455888-5 1 1-456403-3 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119641-1 250 249 248 247 246 245 244 243 242 241 240 239 238 213 198 172 166 164 163 137 136 135 133 119 117 82 71 67 66 63 62 60 59 56 54 53 52 51 50 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079988_GATD DESCRIPTION PRODUCT SPEC - 1 2119640-1 Ocean Side Feed Applicator - DRAWING NO 2151590 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - FEED TYPE MECHANICAL 6 A DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 D 6 PNEUMATIC 56 39 247 246 260 44 7 252 245 35 244 2 7 63 166 242 238 50 163 2 2 2 2 1 REF 34 REF 1 2 3 51 56 6.35 0.50 [ 0.250 0.019 ] 6 8 52 172 D 7 82 137 C 1 4 SERVO LATCH PLATE 4 - 2 8 136 133 - - 243 59 240 APVD 62 59 53 C SEE SHEET 1 DWN 37 38 249 A DATE 40 239 250 DESCRIPTION TERMINAL SUPPORT LOCATION 28 5 41 135 198 A 24 SERVO FEEDER NOT INCLUDED 117 REF 66 11 67 33 B 2 164 10 A 213 19 30 20 29 21 B 9 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 13 47 1 11 11 30mm STROKE 30mm STROKE 30mm STROKE 30 REF 29 REF 119 46 32 34 54 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 19FEB2013 CHK 19FEB2013 APVD 19FEB2013 L.ZHANG L.ZHANG S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151590 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER 4 3 2 20 REVISION DESCRIPTION A 2- 2151590 -2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 5 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 2- 2151590 -1 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST 2- 2151590 -7 A FINE CRIMP HEIGHT ADJUST NONE CRIMP TOOLING KIT PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC 2- 2151590 -5 A CONVERT TO MECHANICAL SERVO LATCH PLATE 7- 2151590 -7 APPLICATOR STYLE CONVERSION CHART - SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED 4 PNEUMATIC FEED - - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - - 1338685-1 - - 1338685-1 1338685-1 - - 5-18022-5 8- 2151590 -5 8- 2151590 -4 5-18022-5 8- 2151590 -5 8- 2151590 -4 5-18022-5 5-18022-5 - - 2119641-2 2119799-1 - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - - - 2168400-6 2168400-6 - 2119799-1 - - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - 6 - - - - - TYPE APPLICATOR INSTRUCTIONS 408-10389 - - - - - TE TERMINAL TERMINAL DATA: MCON-2.8-RECEPTACLE TERMINAL NAME: WIRE STRIP LENGTH 3.20-3.80 mm [.126-.150 IN] C TERMINAL APPLICATION SPECIFICATION n 114-18718 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 1.15-1.40 mm [.045-.055 IN] - - - - - TERMINALS APPLIED TE TERMINAL 1719836-1 TE TERMINAL C1__DWG_PN_1_0 1719836-3 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 0.35mm2 0.22mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.07+/-0.03 [.042+/-.001] 1.00+/-0.03 [.039+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 6.0 8.7 9 - 6 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - 1 B 2 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2151590 -4 2151590 -4 2151590 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 8 9 10 11 A - 1 6 - & 242. - 1 & 152. - 1 MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 1 1 TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 1 1 P - 1 1 - 1 LTR DESCRIPTION DATE SEE SHEET 1 - - 1 - 1 1 - 2 1 REF - - - 1 - - 1 - 1 1 1 - - - - - 1 - - - 1 1 2 - 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-8 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 1338685-1 2168083-8 5018030-1 811242-5 690753-2 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-1 1752356-3 2079383-5 2161328-1 1320908-3 2119959-1 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 462006-6 1-1633129-7 6-240641-5 2119757-8 238011-4 1633965-4 455888-5 1-456403-3 1 - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 1 1 2 1 1 1 1 2 1 3 1 - 2 1 3 - - 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 DWN APVD - - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 16 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .062 SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -27 -25 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 66 - 2063440-1 - 2.29 mm [.090] A PART NUMBERS REQUIRED F O 1.57 mm [.062] REVISIONS DIST - - APPLICATOR DATA LOC 1 DWN 19FEB2013 CHK 19FEB2013 APVD 19FEB2013 L.ZHANG L.ZHANG S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 1-22279-3_SIMP 1 2119082-8 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 1338685-1 2 2168083-8 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 1752356-3 2 2079383-5 1 2161328 1 1320908-3 1 2119959-1 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 462006-6 1 1-1633129-7 1 6-240641-5 .. 1 ITEM_6 1 2119757-8 1 238011-4 1 1633965-4 1 455888-5 1 1-456403-3 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079988_GATD 251 250 249 246 244 243 242 241 240 239 238 213 198 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 82 71 67 66 63 62 59 56 53 52 51 50 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119640-1 DESCRIPTION PRODUCT SPEC - 1 2119782 Ocean Side Feed Applicator - DRAWING NO 2151590 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE APVD - - - 62 6 40 A DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 DWN 251 MECHANICAL D DATE 145 38 239 246 39 59 7 56 140 152 2 D 2 2 244 7 139 243 PNEUMATIC 250 53 2 8 249 242 2 6.35 0.50 [ 0.250 0.019 ] 6 63 238 A 166 50 163 REF 8 34 7 REF 59 82 136 1 137 C 1 TERMINAL SUPPORT LOCATION 52 172 56 2 C 3 1 51 4 28 SERVO LATCH PLATE 5 41 240 133 4 135 198 164 66 2 A 33 SERVO FEEDER NOT INCLUDED 213 A 24 B 67 11 19 10 30 20 117 REF B 21 29 9 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 30mm STROKE 13 1 REF 29 11 REF 30mm STROKE 30mm STROKE 142 30 151 141 32 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 19FEB2013 CHK 19FEB2013 APVD 19FEB2013 L.ZHANG L.ZHANG S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151590 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A