MPD MD212S-03RU Wide 4:1 input, 2w sip single & dual output dc/dc converter Datasheet

MD200RU
Series
Wide 4:1 Input, 2W SIP
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
• Miniature SIP Case
• Wide 4:1 Input Range
• Single & Dual Outputs
• 1,500 VDC Isolation
• >1.0 MHour MTBF
• 21 Standard Models
• Industry Standard Pin-Out
Input
Parameter
Input Voltage Range
Startup Threshold Voltage
Under Voltage Shutdown
Conditions
12 VDC Input
24 VDC Input
48 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
Short Circuit Input Power
Input Filter
Min.
4.5
9.0
18.0
3.0
4.5
8.5
Typ.
12.0
24.0
48.0
4.0
6.0
12.0
Max.
18.0
36.0
75.0
4.5
9.0
18.0
4.0
8.0
16.0
1,500
Units
Max.
±2.0
±2.0
±0.5
±1.0
100
500
±5.0
±0.02
Units
%
%
%
%
mV P - P
mSec
%
%/ºC
Units
VDC
M
pF
kHz
VDC
VDC
VDC
mW
Internal Capacitor
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Transient Recovery Time
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
Conditions
Min.
Typ.
±1.0
±0.3
±0.5
VIN = Min to Max
IOUT = 0% to 100%
See Note 1
300
±3.0
±0.01
Continuous (Autorecovery)
See Note 2
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
Min.
60 Seconds 1,500
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
250
300
500
Min.
-40
Typ.
+25
Max.
+75
+105
+125
Units
ºC
ºC
ºC
95
%
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling, See Note 3
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Ambient
Case
-55
Free Air Convection
RH, Non-condensing
See Mechanical Drawing (Page 2)
Non-Conductive Black Plastic (UL94-V0)
0.07 Oz (2.1g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
2.8
Typ.
Max.
Units
MHours
Conditions
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
Min.
-0.7
-0.7
-0.7
Typ.
Max.
25
50
100
260
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
ºC
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
MD212S-03RU
MD212S-05RU
MD212S-12RU
MD212S-15RU
MD212D-05RU
MD212D-12RU
MD212D-15RU
MD224S-03RU
MD224S-05RU
MD224S-12RU
MD224S-15RU
MD224D-05RU
MD224D-12RU
MD224D-15RU
MD248S-03RU
MD248S-05RU
MD248S-12RU
MD248S-15RU
MD248D-05RU
MD248D-12RU
MD248D-15RU
Output
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load
12
4.5 - 18.0
183
60
12
4.5 - 18.0
208
60
12
4.5 - 18.0
204
60
12
4.5 - 18.0
204
60
12
4.5 - 18.0
208
60
12
4.5 - 18.0
202
60
12
4.5 - 18.0
204
60
24
9.0 - 36.0
92
30
24
9.0 - 36.0
104
30
24
9.0 - 36.0
102
30
24
9.0 - 36.0
102
30
24
9.0 - 36.0
104
30
24
9.0 - 36.0
101
30
24
9.0 - 36.0
102
30
48
18.0 - 75.0
46
20
48
18.0 - 75.0
52
20
48
18.0 - 75.0
51
20
48
18.0 - 75.0
51
20
48
18.0 - 75.0
52
20
48
18.0 - 75.0
51
20
48
18.0 - 75.0
51
20
Voltage
Current
Current
(VDC)
(mA, Max)
(mA, Min)
Notes:
1. When measuring output ripple & noise, it is recommended that an external
ceramic capacitor (0.47 µF typ.) be placed from the +VOUT to the -VOUT pins for
single output units and from each output to common for dual output models.
2. Transient recovery is measured to within a 1% error band for a load step
change of 75% to 100%.
3. Free air convection is typically 20 LFM. The units should not be operated in
still air (0 LFM).
4. Exceeding the absollute ratings could damage the unit.
5. It is recommended that a fuse be used on the input of a power supply for protection.
See the Model Selection table above for the correct rating.
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
500
400
167
134
±200
±83
±67
500
400
167
134
±200
±83
±67
500
400
167
134
±200
±83
±67
(µF, Max)
Fuse
Rating
Slow-Blow
1,000
1,000
170
110
±470
±100
±470
1,000
1,000
170
110
±470
±100
±470
1,000
1,000
170
110
±470
±100
±470
500
500
500
500
500
500
500
250
250
250
250
250
250
250
100
100
100
100
100
100
100
Efficiency Capacitive
Load
(%, Typ)
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
75
80
82
82
80
82
82
75
80
82
82
80
82
82
74
80
82
82
80
82
82
(mA)
Derating
g Curve
Remote ON/OFF
Mechanical Dimensions
The MD200x-xxRU remote control input (pin 3) is current controlled. The unit operates when this input is open. When the input is “high” (current is flowing into the
pin), the converter shuts down. The input current to this pin should be kept between
2 mA and 4 mA. The diagram above shows a simple connection for the control pin.
Using a value of 1 k for R1,a voltage level of 5V - 9V may be used to control the
unit. The table below gives specifications for this feature.
Remote On/Off
Parameter
Supply On
Supply Off
Standby Input Current
Min.
Typ.
Max.
Units
Open or High Impedance
2
4
mA
2.5
mA
Pin Connections
Pin
1
2
4
5
6
7
8
Single
Dual
-VIN
-VIN
+VIN
+VIN
Remote ON/OFF Remote ON/OFF
NC
NC
+VOUT
+VOUT
-VOUT
Common
NC
-VOUT
NC: No Connection
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages