DATASHEET Two Output Differential Buffer for PCIe Gen3 9DB233 Features/Benefits: • OE# pins/Suitable for Express Card applications • PLL or bypass mode/PLL can dejitter incoming clock • Selectable PLL bandwidth/minimizes jitter peaking in downstream PLL's • Spread Spectrum Compatible/tracks spreading input clock for low EMI • SMBus Interface/unused outputs can be disabled Recommended Application: 2 output PCIe Gen3 zero-delay/fanout buffer General Description: The 9DB233 zero-delay buffer supports PCIe Gen3 requirements, while being backwards compatible to PCIe Gen2 and Gen1. The 9DB233 is driven by a differential SRC output pair from an IDT 932S421 or 932SQ420 or equivalent main clock generator. It attenuates jitter on the input clock and has a selectable PLL bandwidth to maximize performance in systems with or without Spread-Spectrum clocking. An SMBus interface allows control of the PLL bandwidth and bypass options, while 2 clock request (OE#) pins make the 9DB233 suitable for Express Card applications. Output Features: • 2 - 0.7V current mode differential output pairs (HCSL) Key Specifications: • Cycle-to-cycle jitter < 50 ps • Output-to-output skew < 50 ps • PCIe Gen3 phase jitter < 1.0ps RMS Block Diagram OE0# OE1# DIF_0 SRC_IN SRC_IN# SPREAD COMPATIBLE PLL DIF_1 PLL_BW SMBDAT CONTROL LOGIC SMBCLK IREF IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 1 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet PLL_BW SRC_IN SRC_IN# vOE0# VDD GND DIF_0 DIF_0# VDD SMBDAT 1 2 3 4 5 6 7 8 9 10 9DB233 Pin Configuration 20 19 18 17 16 15 14 13 12 11 VDDA GNDA IREF vOE1# VDD GND DIF_1 DIF_1# VDD SMBCLK N ote: Pins preceeded by ' v ' have internal 120K ohm pull down resistors Power Distribution Table Pin Number VDD GND 5,9,12,16 6,15 9 6 20 19 20 19 Description Differential Outputs SMBUS IREF Analog VDD & GND for PLL core IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 2 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet Pin Description PIN # PIN NAME PIN TYPE DESCRIPTION 3.3V input for selecting PLL Band Width 0 = low, 1= high 0.7 V Differential SRC TRUE input 0.7 V Differential SRC COMPLEMENTARY input 1 PLL_BW IN 2 3 SRC_IN SRC_IN# IN IN 4 vOE0# IN Activ e low input for enabling DIF pair 0. This pin has an internal pull-down. 1 =disable outputs, 0 = enable outputs 5 6 7 8 9 10 11 12 13 14 15 16 VDD GND DIF_0 DIF_0# VDD SMBDAT SMBCLK VDD DIF_1# DIF_1 GND VDD PWR PWR OUT OUT PWR I/O IN PWR OUT OUT PWR PWR Power supply, nominal 3.3V Ground pin. 0.7V differential true clock output 0.7V differential Complementary clock output Power supply, nominal 3.3V Data pin of SMBUS c ircuitry, 5V tolerant Clock pin of SMBUS circuitry, 5V tolerant Power supply, nominal 3.3V 0.7V differential Complementary clock output 0.7V differential true clock output Ground pin. Power supply, nominal 3.3V 17 vOE1# IN Activ e low input for enabling DIF pair 1. This pin has an internal pull-down. 1 =disable outputs, 0 = enable outputs 18 IREF OUT 19 20 GNDA VDDA PWR PWR This pin establishes the reference for the differential current-mode output pairs. It requires a fixed precision resistor to ground. 475ohm is the standard value for 100ohm differential impedance. Other impedances require different values. See data sheet. Ground pin for the PLL core. 3.3V power for the PLL core. Note: Pins preceeded by ' v ' have internal 120K ohm pull down resistors IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 3 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet Electrical Characteristics - Absolute Maximum Ratings PARAMETER SYMBOL 3.3V Core Supply Voltage 3.3V Logic Supply Voltage Input Low Voltage Input High Voltage Input High Voltage VDDA VDD V IL V IH VIHSMB Storage Temperature Junction Temperature Input ESD protection Ts Tj ESD prot CONDITIONS MIN TYP UNITS NOTES MAX 4.6 4.6 V V V V V GND-0.5 Except for SMBus interface SMBus clock and data pins V DD+0.5V 5.5V -65 Human Body Model 1,2 1,2 1 1 1 1 1 1 ° 150 125 C °C V 2000 1 Guaranteed by design and characterization, not 100% tested in production. 2 Operation under these conditions is neither implied nor guaranteed. Electrical Characteristics - Input/Supply/Common Parameters TA = TCOM or TIND; Supply Voltage VDD = 3.3 V +/-5% PARAMETER SYMBOL Ambient Operating Temperature TCOM TIND Input High Voltage VIH Input Low Voltage VIL I IN Input Current Input Frequency Pin Inductance Capacitance IINP Fibyp Fipll Lpin CIN CINDIF_IN CONDITIONS MIN Commmercial range Industrial range Single-ended inputs, except SMBus, low threshold and tri-level inputs Single-ended inputs, except SMBus, low threshold and tri-level inputs Single-ended inputs, VIN = GND, VIN = VDD 0 -40 TYP 70 85 °C °C 1 1 2 VDD + 0.3 V 1 GND - 0.3 0.8 V 1 -5 5 uA 1 Single-ended inputs VIN = 0 V; Inputs with internal pull-up resistors VIN = VDD; Inputs with internal pull-down resistors -200 200 uA 1 VDD = 3.3 V, Bypass mode VDD = 3.3 V, 100MHz PLL mode 10 33 Logic Inputs, except DIF_IN DIF_IN differential clock inputs 1.5 1.5 110 110 7 5 2.7 MHz MHz nH pF pF 2 2 1 1 1,4 100.00 MAX UNITS NOTES COUT Output pin capacitance 6 pF 1 Clk Stabilization TSTAB From VDD Power-Up and after input clock stabilization or de-assertion of PD# to 1st clock 1.8 ms 1,2 Input SS Modulation Frequency f MODIN Allowable Frequency (Triangular Modulation) 30 33 kHz 1 OE# Latency t LATOE# 1 3 cycles 1,3 Tdrive_PD# t DRVPD 300 us 1,3 Tfall Trise SMBus Input Low Voltage SMBus Input High Voltage SMBus Output Low Voltage SMBus Sink Current Nominal Bus Voltage SCLK/SDATA Rise Time SCLK/SDATA Fall Time SMBus Operating Frequency tF tR DIF start after OE# assertion DIF stop after OE# deassertion DIF output enable after PD# de-assertion Fall time of control inputs Rise time of control inputs VILSMB VIHSMB VOLSMB I PULLUP VDDSMB t RSMB t FSMB 5 5 0.8 @ I PULLUP @ VOL 3V to 5V +/- 10% (Max VIL - 0.15) to (Min VIH + 0.15) (Min VIH + 0.15) to (Max VIL - 0.15) 5.5 1000 300 ns ns V V V mA V ns ns 1,2 1,2 1 1 1 1 1 1 1 f MAXSMB Maximum SMBus operating frequency 100 kHz 1,5 2.1 4 2.7 VDDSMB 0.4 1 Guaranteed by design and characterization, not 100% tested in production. Control input must be monotonic from 20% to 80% of input swing. 3 Time from deassertion until outputs are >200 mV 4 DIF_IN input 2 5 The differential input clock must be running for the SMBus to be active IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 4 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet Electrical Characteristics - Clock Input Parameters TA = TCOM or TIND; Supply Voltage VDD = 3.3 V +/-5% PARAMETER SYMBOL Input High Voltage - DIF_IN VIHDIF Input Low Voltage - DIF_IN VILDIF Input Common Mode Voltage - DIF_IN Input Amplitude - DIF_IN Input Slew Rate - DIF_IN Input Leakage Current Input Duty Cycle Input Jitter - Cycle to Cycle 1 2 CONDITIONS Differential inputs (single-ended measurement) Differential inputs (single-ended measurement) MIN TYP MAX UNITS NOTES 600 800 1150 mV 1 VSS - 300 0 300 mV 1 VCOM Common Mode Input Voltage 300 1000 mV 1 VSWING dv/dt I IN dtin J DIFIn Peak to Peak value Measured differentially VIN = VDD , VIN = GND Measurement from differential wavefrom Differential Measurement 300 0.4 -5 45 0 1450 8 5 55 125 mV V/ns uA % ps 1 1,2 1 1 1 Guaranteed by design and characterization, not 100% tested in production. Slew rate measured through +/-75mV window centered around differential zero Electrical Characteristics - DIF 0.7V Current Mode Differential Outputs TA = TCOM or TIND; Supply Voltage VDD = 3.3 V +/-5% PARAMETER SYMBOL Slew rate Slew rate matching Trf ∆Trf CONDITIONS MIN TYP MAX UNITS NOTES V/ns 1, 2, 3 Scope averaging on 0.6 2.5 4 % Slew rate matching, Scope averaging on 9.5 20 1, 2, 4 Statistical measurement on single-ended signal Voltage High VHigh 660 740 850 1 using oscilloscope math function. (Scope averaging mV Voltage Low VLow -150 8 150 1 on) Measurement on single ended signal using absolute Max Voltage Vmax 760 1150 1 mV value. (Scope averaging off) Min Voltage Vmin -300 -3 1 Vswing Vswing Scope averaging off 300 1506 mV 1, 2 Crossing Voltage (abs) Vcross_abs Scope averaging off 250 378 550 mV 1, 5 Crossing Voltage (var) ∆-Vcross Scope averaging off 54 140 mV 1, 6 1 Guaranteed by design and characterization, not 100% tested in production. IREF = VDD/(3xRR). For RR = 475Ω (1%), IREF = 2.32mA. IOH = 6 x IREF and VOH = 0.7V @ ZO=50Ω (100Ω differential impedance). 2 Measured from differential waveform Slew rate is measured through the Vswing voltage range centered around differential 0V. This results in a +/-150mV window around differential 0V. 3 4 Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is measured using a +/-75mV window centered on the average cross point where Clock rising meets Clock# falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. 5 Vcross is defined as voltage where Clock = Clock# measured on a component test board and only applies to the differential rising edge (i.e. Clock rising and Clock# falling). 6 The total variation of all Vcross measurements in any particular system. Note that this is a subset of V_cross_min/max (V_cross absolute) allowed. The intent is to limit Vcross induced modulation by setting V_cross_delta to be smaller than V_cross absolute. Electrical Characteristics - Current Consumption TA = TCOM or TIND; Supply Voltage VDD = 3.3 V +/-5% PARAMETER SYMBOL Operating Supply Current Powerdown Current 1 I DD3.3OP I DD3.3PD I DD3.3PDZ CONDITIONS All outputs active @100MHz, CL = Full load; All diff pairs driven All differential pairs tri-stated MIN TYP MAX 70 80 N/A N/A UNITS NOTES mA mA mA 1 1 1 Guaranteed by design and characterization, not 100% tested in production. IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 5 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet Electrical Characteristics - Output Duty Cycle, Jitter, Skew and PLL Characterisitics TA = TCOM or TIND; Supply Voltage VDD = 3.3 V +/-5% PARAMETER SYMBOL CONDITIONS MIN TYP MAX PLL Bandwidth BW PLL Jitter Peaking Duty Cycle Duty Cycle Distortion 2 0.4 t JPEAK t DC -3dB point in High BW Mode -3dB point in Low BW Mode Peak Pass band Gain Measured differentially, PLL Mode 45 2.3 0.5 1 48 4 1 2 55 MHz MHz dB % 1 1 1 1 t DCD Measured differentially, Bypass Mode @100MHz -2 1 2 % 1,4 Jitter, Cycle to cycle tjcyc-cyc Bypass Mode, VT = 50% Hi BW PLL Mode V T = 50% VT = 50% PLL mode Additive Jitter in Bypass Mode 2500 -250 Skew, Output to Output t pdBYP t pdPLL t sk3 3660 0 15 40 10 4500 250 50 50 50 ps ps ps ps ps 1 1 1 1,3 1,3 Skew, Input to Output UNITS NOTES 1 Guaranteed by design and characterization, not 100% tested in production. I REF = VDD/(3xRR). For RR = 475Ω (1%), I REF = 2.32mA. I OH = 6 x I REF and V OH = 0.7V @ ZO=50Ω. 3 Measured from differential waveform 4 Duty cycle distortion is the difference in duty cycle between the output and the input clock when the device is operated in bypass mode. 2 Electrical Characteristics - PCIe Phase Jitter Parameters TA = TCOM or TIND; Supply Voltage VDD = 3.3 V +/-5% PARAMETER Phase Jitter, PLL Mode SYMBOL t jphPCIeG1 t jphPCIeG2 t jphPCIeG3 t jphPCIeG1 Additive Phase Jitter, Bypass Mode t jphPCIeG2 t jphPCIeG3 CONDITIONS PCIe Gen 1 PCIe Gen 2 Lo Band 10kHz < f < 1.5MHz PCIe Gen 2 High Band 1.5MHz < f < Nyquist (50MHz) PCIe Gen 3 (PLL BW of 2-4MHz, CDR = 10MHz) PCIe Gen 1 PCIe Gen 2 Lo Band 10kHz < f < 1.5MHz PCIe Gen 2 High Band 1.5MHz < f < Nyquist (50MHz) PCIe Gen 3 (PLL BW of 2-4MHz, CDR = 10MHz) MIN TYP 32 MAX 86 1.1 3 2.3 3.1 0.5 1 2 5 0.2 0.3 0.8 1 0.1 0.2 UNITS Notes ps (p-p) 1,2,3 ps 1,2 (rms) ps 1,2 (rms) ps 1,2,4 (rms) ps (p-p) ps (rms) ps (rms) ps (rms) 1,2,3 1,2 1,2 1,2,4 1 Applies to all outputs. See http://www.pcisig.com for complete specs 3 Sample size of at least 100K cycles. This figures extrapolates to 108ps pk-pk @ 1M cycles for a BER of 1-12. 4 Subject to final radification by PCI SIG. 2 IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 6 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet SRC Reference Clock Common Recommendations for Differential Routing Dimension or Value L1 length, route as non-coupled 50ohm trace 0.5 max L2 length, route as non-coupled 50ohm trace 0.2 max L3 length, route as non-coupled 50ohm trace 0.2 max Rs 33 Rt 49.9 Unit inch inch inch ohm ohm Figure 1 1 1 1 1 Down Device Differential Routing L4 length, route as coupled microstrip 100ohm differential trace 2 min to 16 max L4 length, route as coupled stripline 100ohm differential trace 1.8 min to 14.4 max inch inch 1 1 Differential Routing to PCI Express Connector L4 length, route as coupled microstrip 100ohm differential trace 0.25 to 14 max L4 length, route as coupled stripline 100ohm differential trace 0.225 min to 12.6 max inch inch 2 2 Figure 1: Down Device Routing L2 L1 Rs L4 L4' L2' L1' Rs Rt HCSL Output Buffer Rt L3' PCI Express Down Device REF_CLK Input L3 Figure 2: PCI Express Connector Routing L2 L1 Rs L4 L4' L2' L1' Rs Rt HCSL Output Buffer Rt L3' IDT® Two Output Differential Buffer for PCIe Gen3 PCI Express Add-in Board REF_CLK Input L3 1667C—04/20/11 7 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet Alternative Termination for LVDS and other Common Differential Signals (figure 3) Vdiff Vp-p Vcm R1 R2 R3 R4 Note 0.45v 0.22v 1.08 33 150 100 100 0.58 0.28 0.6 33 78.7 137 100 0.80 0.40 0.6 33 78.7 none 100 ICS874003i-02 input compatible 0.60 0.3 1.2 33 174 140 100 Standard LVDS R1a = R1b = R1 R2a = R2b = R2 Figure 3 L2 L1 R3 R1a L4 R4 L4' L2' L1' R1b R2a HCSL Output Buffer R2b L3' Down Device REF_CLK Input L3 Cable Connected AC Coupled Application (figure 4) Component Value Note R5a, R5b 8.2K 5% R6a, R6b 1K 5% Cc 0.1 µF Vcm 0.350 volts Figure 4 3.3 Volts R5a R5b R6a R6b Cc L4 L4' Cc IDT® Two Output Differential Buffer for PCIe Gen3 PCIe Device REF_CLK Input 1667C—04/20/11 8 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet General SMBus serial interface information for the ICS9DB233 How to Write: How to Read: Controller (host) sends a start bit. Controller (host) sends the write address D4 (H) ICS clock will acknowledge Controller (host) sends the begining byte location = N ICS clock will acknowledge Controller (host) sends the data byte count = X ICS clock will acknowledge Controller (host) starts sending Byte N through Byte N + X -1 (see Note 2) • ICS clock will acknowledge each byte one at a time • Controller (host) sends a Stop bit • • • • • • • • • • • • Controller (host) will send start bit. Controller (host) sends the write address D4 (H) ICS clock will acknowledge Controller (host) sends the begining byte location = N ICS clock will acknowledge Controller (host) will send a separate start bit. Controller (host) sends the read address D5 (H) ICS clock will acknowledge ICS clock will send the data byte count = X ICS clock sends Byte N + X -1 ICS clock sends Byte 0 through byte X (if X(H) was written to byte 8). Controller (host) will need to acknowledge each byte Controllor (host) will send a not acknowledge bit Controller (host) will send a stop bit • • • • • • • • • • Index Block Write Operation Controlle r (Host) starT bit T Slave Address D4(H ) WR W Rite Index Block Read Operation Controlle r (Host) T starT bit Slave Address D4(H ) WR W Rite ICS (Sla ve /Re ce ive r) ICS (Sla ve /Re ce ive r) ACK ACK Beginning Byte = N Beginning Byte = N ACK ACK Data Byte Count = X RT Repeat starT Slave Address D3(H ) RD ReaD ACK Beginning Byte N ACK X Byte ACK Data Byte Count = X ACK Beginning Byte N Byte N + X - 1 ACK X Byte ACK P stoP bit Byte N + X - 1 N P IDT® Two Output Differential Buffer for PCIe Gen3 Not acknowledge stoP bit 1667C—04/20/11 9 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet SMB us Table: Device C ontrol Register, READ/WRITE ADDRESS (D4/D5) Byte 0 Pin # Name Control Function Type 0 PLL Functions Enables SMBus controlled by SW_EN Control of bite 1 RW Bit 7 SMBus and 0 registers RESERVED RW Bit 6 RESERVED RW Bit 5 RESERVED RW Bit 4 RESERVED RW Bit 3 RESERVED RW Bit 2 Selects PLL Bit 1 PLL BW #adjust RW Low BW Bandwidth Bypasses PLL for PLL bypassed PLL Enable RW Bit 0 board test (fan out mode) SMB us Table: Output Enable Register Byte 1 Pin # Name Control Function Type RESERVED RW Bit 7 RESERVED RW Bit 6 RW RESERVED Bit 5 RESERVED RW Bit 4 RESERVED RW Bit 3 RESERVED RW Bit 2 RW RESERVED Bit 1 RESERVED RW Bit 0 SMB us Table: Function Select Register Byte 2 Pin # Name Control Function Type RESERVED Bit 7 RW RESERVED Bit 6 RW RESERVED Bit 5 RW RESERVED Bit 4 RW RESERVED Bit 3 RW RESERVED Bit 2 RW RESERVED Bit 1 RW RESERVED Bit 0 RW SMB us Table: Vendor & Revision ID Register Byte 3 Pin # Name Control Function Type RID3 R Bit 7 RID2 R Bit 6 REVISION ID RID1 R Bit 5 RID0 R Bit 4 VID3 R Bit 3 Bit 2 VID2 R VENDOR ID Bit 1 VID1 R VID0 R Bit 0 IDT® Two Output Differential Buffer for PCIe Gen3 0 1 Default PLL Functions controlled by device pins 1 X X X X X High BW 1 PLL enabled (ZDB mode) 1 1 Default X X X X X X X X 1 Default X X X X X X X X 1 - Default 0 0 0 1 0 0 0 1 - 0 - 0 - 1667C—04/20/11 10 9DB233 Two Output Differential Buffer for PCIe Gen3 SMBus Table: DEVICE ID Byte 4 Pin # Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Datasheet Control Function Type R R R Device ID R = 06 Hex R R R R 0 1 Default 0 0 0 0 0 1 1 0 - SMBus Table: Byte Count Register Pin # Byte 5 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 - Name Control Function Type 0 1 Default BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 Writing to this register will configure how many bytes will be read back, default is 06 = 6 bytes. RW RW RW RW RW RW RW RW - - 0 0 0 0 0 1 1 0 IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 11 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet 20-pin SSOP Package Drawing and Dimensions SYMBOL A A1 A2 b c D E E1 e L N a ZD IDT® Two Output Differential Buffer for PCIe Gen3 20-Lead, 150 mil SSOP (QSOP) In Millimeters In Inches COMMON DIMENSIONS COMMON DIMENSIONS MIN MAX MIN MAX 1.35 1.75 .053 .069 0.10 0.25 .004 .010 -1.50 -.059 0.20 0.30 .008 .012 0.18 0.25 .007 .010 SEE VARIATIONS SEE VARIATIONS 5.80 6.20 .228 .244 3.80 4.00 .150 .157 0.635 BASIC 0.025 BASIC 0.40 1.27 .016 .050 SEE VARIATIONS SEE VARIATIONS 0° 8° 0° 8° SEE VARIATIONS SEE VARIATIONS 1667C—04/20/11 12 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet 20-pin TSSOP Package Drawing and Dimensions 20-Lead, 4.40 mm. Body, 0.65 mm. Pitch TSSOP (173 mil) (25.6 mil) In Millimeters In Inches SYMBOL COMMON DIMENSIONS COMMON DIMENSIONS MIN MAX MIN MAX A -1.20 -.047 A1 0.05 0.15 .002 .006 A2 0.80 1.05 .032 .041 b 0.19 0.30 .007 .012 c 0.09 0.20 .0035 .008 D SEE VARIATIONS SEE VARIATIONS E 6.40 BASIC 0.252 BASIC E1 4.30 4.50 .169 .177 e 0.65 BASIC 0.0256 BASIC L 0.45 0.75 .018 .030 N SEE VARIATIONS SEE VARIATIONS a 0° 8° 0° 8° aaa -0.10 -.004 c N L E1 E INDEX AREA 1 2 α D A A2 VARIATIONS A1 - Ce N SEATING PLANE b 20 aaa C D mm. MIN 6.40 D (inch) MAX 6.60 MIN .252 MAX .260 Reference Doc.: JEDEC Publication 95, MO-153 10-0035 Ordering Information Part / Order Number Shipping Packaging 9DB233AFLF Tubes 9DB233AFLFT Tape and Reel 9DB233AFILF Tubes 9DB233AFILFT Tape and Reel 9DB233AGLF Tubes 9DB233AGLFT Tape and Reel 9DB233AGILF Tubes 9DB233AGILFT Tape and Reel Package 20-pin SSOP 20-pin SSOP 20-pin SSOP 20-pin SSOP 20-pin TSSOP 20-pin TSSOP 20-pin TSSOP 20-pin TSSOP Temperature 0 to +70°C 0 to +70°C -40 to +85°C -40 to +85°C 0 to +70°C 0 to +70°C -40 to +85°C -40 to +85°C "LF" after the package code are the Pb-Free configuration and are RoHS compliant. "A" is the device revision designator (will not correlate to the datasheet revision). IDT® Two Output Differential Buffer for PCIe Gen3 1667C—04/20/11 13 9DB233 Two Output Differential Buffer for PCIe Gen3 Datasheet Revision History Rev. 0.1 Who Issue Date Description RDW 4/28/2010 1. Initial Release 0.2 RDW 6/3/2010 0.3 A B C RDW RDW RDW RDW 6/25/2010 6/30/2010 7/12/2010 4/20/2011 Page # 1. Updated Pin names to match other 9DB devices CLKREQ# becomes OE# and PCIEXyy becomes DIF_yy 2. Updated maximum rise/fall time to 550ps from 700ps. This translates to a minimum slew rate of 0.67V/ns thus meeting the PCIe spec of 0.6V/ns. 3. Updated phase jitter tables to remove references to QPI. 4. Reformatted DS to have common format amongst all 9DBx33 DS. 5. Updated block diagram to match item 1 1. Updated electrical tables to new standard format for 9DB devices. 2. Cleaned up front page text. Released to final 1. Changed PWD to Default in SMBus tables. Changed pull down indicator from '**' to ' v '. 6 1, 3-6 10,11 Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 408-284-6578 [email protected] Corporate Headquarters Asia Pacific and Japan Europe Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) IDT Singapore Pte. Ltd. 1 Kallang Sector #07-01/06 KolamAyer Industrial Park Singapore 349276 Phone: 65-6-744-3356 Fax: 65-6-744-1764 IDT Europe Limited 321 Kingston Road Leatherhead, Surrey KT22 7TU England Phone: 44-1372-363339 Fax: 44-1372-378851 © 2010 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT, ICS, and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA 14