Allegro A6595KA 8-bit serial-input, dmos power driver Datasheet

ADVANCE INFORMATION
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
(Subject to change without notice)
January 24, 2000
POWER
GROUND
1
LOGIC
SUPPLY
2
SERIAL
DATA IN
20
POWER
GROUND
19
LOGIC
GROUND
3
18
SERIAL
DATA OUT
OUT 0
4
17
OUT 7
OUT 1
5
16
OUT 6
OUT 2
6
15
OUT 5
OUT 3
7
14
OUT 4
REGISTER
CLEAR
8
CLR
CLK
13
CLOCK
OUTPUT
ENABLE
9
OE
ST
12
STROBE
POWER
GROUND
10
11
POWER
GROUND
LATCHES
REGISTER
LATCHES
REGISTER
VDD
Dwg. PP-029-13
Note that the A6595KA (DIP) and the A6595KLW (SOIC)
are electrically identical and share a common terminal
number assignment.
ABSOLUTE MAXIMUM RATINGS
at TA = 25°C
Output Voltage, VO ............................... 50 V
Output Drain Current,
Continuous, IO .......................... 250 mA*
Peak, IOM ................................. 750 mA*†
Peak, IOM ....................................... 2.0 A†
Single-Pulse Avalanche Energy,
EAS ................................................. 75 mJ
Logic Supply Voltage, VDD .................. 7.0 V
Input Voltage Range,
VI ................................... -0.3 V to +7.0 V
Package Power Dissipation,
PD ........................................... See Graph
Operating Temperature Range,
TA ................................. -40°C to +125°C
Storage Temperature Range,
TS ................................. -55°C to +150°C
* Each output, all outputs on.
† Pulse duration ≤ 100 µs, duty cycle ≤ 2%.
Caution: These CMOS devices have input static
protection (Class 3) but are still susceptible to damage if
exposed to extremely high static electrical charges.
Data Sheet
26185.120
6595
The A6595KA and A6595KLW combine an 8-bit CMOS shift
register and accompanying data latches, control circuitry, and DMOS
power driver outputs. Power driver applications include relays, solenoids, and other medium-current or high-voltage peripheral power
loads.
The serial-data input, CMOS shift register and latches allow direct
interfacing with microprocessor-based systems. Serial-data input rates
are over 5 MHz. Use with TTL may require appropriate pull-up
resistors to ensure an input logic high.
A CMOS serial-data output enables cascade connections in applications requiring additional drive lines. Similar devices with reduced
rDS(on) are available as the A6A595.
The A6595 DMOS open-drain outputs are capable of sinking up to
750 mA. All of the output drivers are disabled (the DMOS sink drivers
turned off) by the OUTPUT ENABLE input high.
The A6595KA is furnished in a 20-pin dual in-line plastic package.
The A6595KLW is furnished in a wide-body, small-outline plastic
package (SOIC) with gull-wing leads. Copper lead frames, reduced
supply current requirements, and low on-state resistance allow both
devices to sink 150 mA from all outputs continuously, to ambient
temperatures over 85°C.
FEATURES
■ 50 V Minimum Output Clamp Voltage
■ 250 mA Output Current (all outputs simultaneously)
■ 1.3 Ω Typical rDS(on)
■ Low Power Consumption
■ Replacements for TPIC6595N and TPIC6595DW
Always order by complete part number:
Part Number
Package
A6595KA
20-pin DIP
A6595KLW
20-lead SOIC
RθJA
55°C/W
70°C/W
RθJC
25°C/W
17°C/W
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
LOGIC SYMBOL
2.5
9
12
2.0
SU
FF
IX
1.5
SU
FF
IX
'A
', R
θJ
A =
'LW
', R
θJ
1.0
G3
C2
SRG8
8
13
R
3
1D
C1
2
4
55
°C
/W
5
6
A
=7
0°
C/
W
7
14
0.5
15
16
2
0
25
50
75
100
125
AMBIENT TEMPERATURE IN °C
17
150
18
Dwg. GS-004A
Dwg. FP-043
FUNCTIONAL BLOCK DIAGRAM
REGISTER
CLEAR
(ACTIVE LOW)
V DD
CLOCK
SERIAL
DATA IN
SERIAL-PARALLEL SHIFT REGISTER
STROBE
D-TYPE LATCHES
LOGIC
SUPPLY
SERIAL
DATA OUT
OUTPUT
ENABLE
(ACTIVE LOW)
LOGIC
GROUND
POWER
GROUND
POWER
GROUND
OUT 0
OUT N
Grounds (terminals 1, 10, 11, 19, and 20) must be connected together externally.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright © 2000, Allegro MicroSystems, Inc.
Dwg. FP-013-5
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
OUT
VDD
IN
Dwg. EP-063-3
Dwg. EP-010-15
DMOS POWER DRIVER OUTPUT
LOGIC INPUTS
VDD
RECOMMENDED OPERATING CONDITIONS
OUT
over operating temperature range
Logic Supply Voltage Range, VDD ............... 4.5 V to 5.5 V
High-Level Input Voltage, VIH ............................ ≥ 0.85VDD
Low-level input voltage, VIL ................................. ≤0.15VDD
Dwg. EP-063-2
SERIAL DATA OUT
TRUTH TABLE
Shift Register Contents
Data Clock
Input Input
I0
I1
I2
...
I6
H
H
R0 R1
…
R5 R6
R6
L
L
R0 R1
…
R5 R6
R6
R0 R1 R2
…
R6 R7
R7
X
X
…
X
X
X
P0 P1 P2
…
P6 P7
P7
X
X
L = Low Logic Level
I7
Serial
Data
Output Strobe
H = High Logic Level
www.allegromicro.com
—
X = Irrelevant
Latch Contents
I0
I1
...
I6
R0 R1 R2
…
R6 R7
P0 P1 P2
…
P6 P7
L
P0 P1 P2
…
P6 P7
X
…
X
H
H
…
H
X
I2
Output Contents
X
P = Present State
I7
Output
Enable
X
R = Previous State
I0
I1
H
I2
H
…
I6
I7
H
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
ELECTRICAL CHARACTERISTICS at TA = +25°C, VDD = 5 V, tir = tif ≤ 10 ns (unless otherwise
specified).
Limits
Characteristic
Symbol
Test Conditions
Output Breakdown
Voltage
V(BR)DSX
IDSX
Off-State Output
Current
Static Drain-Source
On-State Resistance
rDS(on)
Min.
Typ.
Max.
Units
IO = 1 mA
50
—
—
V
VO = 40 V
—
0.05
1.0
µA
VO = 40 V, TA = 125°C
—
0.15
5.0
µA
IO = 250 mA, VDD = 4.5 V
—
1.3
2.0
Ω
IO = 250 mA, VDD = 4.5 V, TA = 125°C
—
2.0
3.2
Ω
IO = 500 mA, VDD = 4.5 V (see note)
—
1.3
2.0
Ω
Nominal Output
Current
ION
VDS(on) = 0.5 V, TA = 85°C
—
250
—
mA
Logic Input Current
IIH
VI = VDD = 5.5 V
—
—
1.0
µA
IIL
VI = 0, VDD = 5.5 V
—
—
-1.0
µA
—
1.3
—
V
IOH = -20 µA, VDD = 4.5 V
4.4
4.49
—
V
IOH = -4 mA, VDD = 4.5 V
4.1
4.3
—
V
IOL = 20 µA, VDD = 4.5 V
—
0.002
0.1
V
IOL = 4 mA, VDD = 4.5 V
—
0.2
0.4
V
tPLH
IO = 250 mA, CL = 30 pF
—
650
—
ns
tPHL
IO = 250 mA, CL = 30 pF
—
150
—
ns
Output Rise Time
tr
IO = 250 mA, CL = 30 pF
—
7500
—
ns
Output Fall Time
tf
IO = 250 mA, CL = 30 pF
—
425
—
ns
IDD(OFF)
All inputs low
—
15
100
µA
IDD(ON)
VDD = 5.5 V, Outputs on
—
150
300
µA
IDD(fclk)
fclk = 5 MHz, CL = 30 pF, Outputs off
—
0.6
5.0
mA
Logic Input Hysteresis
SERIAL-DATA
Output Voltage
VI(hys)
VOH
VOL
Prop. Delay Time
Supply Current
Typical Data is at VDD = 5 V and is for design information only.
NOTE — Pulse test, duration ≤100 µs, duty cycle ≤2%.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
TIMING REQUIREMENTS and SPECIFICATIONS
(Logic Levels are VDD and Ground)
C
50%
CLOCK
A
SERIAL
DATA IN
B
DATA
50%
tp
SERIAL
DATA OUT
DATA
50%
D
E
STROBE
50%
OUTPUT
ENABLE
LOW = ALL OUTPUTS ENABLED
tp
HIGH = OUTPUT OFF
DATA
50%
OUT N
LOW = OUTPUT ON
Dwg. WP-029-2
HIGH = ALL OUTPUTS DISABLED
OUTPUT
ENABLE
50%
t PLH
t PHL
tf
tr
90%
OUT N
DATA
10%
Dwg. WP-030-2
A. Data Active Time Before Clock Pulse
(Data Set-Up Time), tsu(D) .......................................... 10 ns
B. Data Active Time After Clock Pulse
(Data Hold Time), th(D) .............................................. 10 ns
C. Clock Pulse Width, tw(CLK) ............................................. 20 ns
D. Time Between Clock Activation
and Strobe, tsu(ST) ....................................................... 50 ns
E. Strobe Pulse Width, tw(ST) .............................................. 50 ns
F. Output Enable Pulse Width, tw(OE) ................................ 4.5 µs
NOTE – Timing is representative of a 12.5 MHz clock.
Higher speeds are attainable.
www.allegromicro.com
Serial data present at the input is transferred to the shift
register on the rising edge of the CLOCK input pulse. On
succeeding CLOCK pulses, the registers shift data information
towards the SERIAL DATA OUTPUT.
Information present at any register is transferred to the
respective latch on the rising edge of the STROBE input pulse
(serial-to-parallel conversion).
When the OUTPUT ENABLE input is high, the output
source drivers are disabled (OFF). The information stored in the
latches is not affected by the OUTPUT ENABLE input. With
the OUTPUT ENABLE input low, the outputs are controlled by
the state of their respective latches.
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
TEST CIRCUITS
+15 V
0.11 Ω
INPUT
100 mH
tav
IAS = 1.0 A
IO
DUT
OUT
VO
V(BR)DSX
VO(ON)
Dwg. EP-066-1
EAS = IAS x V(BR)DSX x tAV/2
Single-Pulse Avalanche Energy Test Circuit
and Waveforms
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
TERMINAL DESCRIPTIONS
Terminal No.
Terminal Name
Function
1
POWER GROUND
2
LOGIC SUPPLY
3
SERIAL DATA IN
4-7
OUT0-3
Current-sinking, open-drain DMOS output terminals.
8
CLEAR
When (active) low, the registers are cleared (set low).
9
OUTPUT ENABLE
When (active) low, the output drivers are enabled; when high, all output
drivers are turned OFF (blanked).
10
POWER GROUND
Reference terminal for output voltage measurements (OUT0-3).
11
POWER GROUND
Reference terminal for output voltage measurements (OUT0-7).
12
STROBE
Data strobe input terminal; shift register data is latched on rising edge.
13
CLOCK
Clock input terminal for data shift on rising edge.
14-17
OUT4-7
Current-sinking, open-drain DMOS output terminals.
18
SERIAL DATA OUT
19
LOGIC GROUND
Reference terminal for input voltage measurements.
20
POWER GROUND
Reference terminal for output voltage measurements (OUT4-7).
Reference terminal for output voltage measurements (OUT0-3).
(VDD) The logic supply voltage (typically 5 V).
Serial-data input to the shift-register.
CMOS serial-data output to the following shift register.
NOTE — Grounds (terminals 1, 10, 11, 19, and 20) must be connected together externally.
www.allegromicro.com
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
A6595KA
Dimensions in Inches
(controlling dimensions)
20
0.014
0.008
11
0.430
MAX
0.280
0.240
0.300
BSC
1
0.070
0.045
0.100
1.060
0.980
10
0.005
BSC
MIN
0.210
MAX
0.150
0.115
0.015
MIN
0.022
0.014
Dwg. MA-001-20 in
Dimensions in Millimeters
(for reference only)
0.355
0.204
11
20
10.92
MAX
7.11
6.10
7.62
BSC
1
1.77
1.15
2.54
26.92
24.89
BSC
10
0.13
MIN
5.33
MAX
3.81
2.93
0.39
MIN
0.558
0.356
Dwg. MA-001-20 mm
NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown.
2. Lead spacing tolerance is non-cumulative
3. Lead thickness is measured at seating plane or below.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
A6595KLW
Dimensions in Inches
(for reference only)
20
11
0.0125
0.0091
0.419
0.394
0.2992
0.2914
0.050
0.016
0.020
0.013
1
2
0.050
3
0° TO 8°
BSC
0.5118
0.4961
0.0926
0.1043
0.0040 MIN.
Dwg. MA-008-20 in
Dimensions in Millimeters
(controlling dimensions)
20
11
0.32
0.23
10.65
10.00
7.60
7.40
1.27
0.40
0.51
0.33
1
2
1.27
3
13.00
12.60
BSC
0° TO 8°
2.65
2.35
0.10 MIN.
NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown.
2. Lead spacing tolerance is non-cumulative.
www.allegromicro.com
Dwg. MA-008-20 mm
6595
8-BIT SERIAL-INPUT,
DMOS POWER DRIVER
The products described here are manufactured under one or more
U.S. patents or U.S. patents pending.
Allegro MicroSystems, Inc. reserves the right to make, from time to
time, such departures from the detail specifications as may be
required to permit improvements in the performance, reliability, or
manufacturability of its products. Before placing an order, the user is
cautioned to verify that the information being relied upon is current.
Allegro products are not authorized for use as critical components
in life-support devices or systems without express written approval.
The information included herein is believed to be accurate and
reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of
third parties which may result from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Similar pages