TI ACT16373QEP 16-bit d-type transparent latch with 3-state output Datasheet

SN74ACT16373Q-EP
16-BIT D-TYPE TRANSPARENT LATCH
WITH 3-STATE OUTPUTS
SCAS678B – MAY 2002 – REVISED JULY 2002
D
D
D
D
D
D
D
D
D
D
DL PACKAGE
(TOP VIEW)
Controlled Baseline
– One Assembly/Test Site, One Fabrication
Site
Extended Temperature Performance of
–40°C to 125°C
Enhanced Diminishing Manufacturing
Sources (DMS) Support
Enhanced Product Change Notification
Qualification Pedigree†
Member of the Texas Instruments
Widebus Family
Inputs Are TTL-Voltage Compatible
3-State Bus Driving True Outputs
Full Parallel Access for Loading
Distributed VCC and GND Pins Minimize
High-Speed Switching Noise
1OE
1Q1
1Q2
GND
1Q3
1Q4
VCC
1Q5
1Q6
GND
1Q7
1Q8
2Q1
2Q2
GND
2Q3
2Q4
VCC
2Q5
2Q6
GND
2Q7
2Q8
2OE
† Component qualification in accordance with JEDEC and industry
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, highly
accelerated stress test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life.
description
The SN74ACT16373Q-EP is a 16-bit D-type
transparent latch with 3-state outputs, designed
specifically for driving highly capacitive or
relatively low-impedance loads. It is particularly
suitable for implementing buffer registers, I/O
ports, bidirectional bus drivers, and working
registers.
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
1LE
1D1
1D2
GND
1D3
1D4
VCC
1D5
1D6
GND
1D7
1D8
2D1
2D2
GND
2D3
2D4
VCC
2D5
2D6
GND
2D7
2D8
2LE
This device can be used as two 8-bit latches or one 16-bit latch. The Q outputs of the latches follow the data
(D) inputs if the latch-enable (LE) input is taken high. When LE is taken low, the Q outputs are latched at the
levels set up at the D inputs.
A buffered output-enable (OE) input can be used to place the outputs in either a normal logic state (high or low
logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the
bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines
in a bus-organized system, without need for interface or pullup components.
OE does not affect the internal operations of the latches. Old data can be retained or new data can be entered
while the outputs are in the high-impedance state.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN74ACT16373Q-EP
16-BIT D-TYPE TRANSPARENT LATCH
WITH 3-STATE OUTPUTS
SCAS678B – MAY 2002 – REVISED JULY 2002
ORDERING INFORMATION
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
–40°C to 125°C
SSOP – DL
Tape and reel
SN74ACT16373QDLREP
ACT16373QEP
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
FUNCTION TABLE
(each section)
INPUTS
OE
LE
D
OUTPUT
Q
L
H
H
H
L
H
L
L
L
L
X
Q0
H
X
X
Z
logic diagram (positive logic)
1OE
1LE
1
2OE
48
2LE
C1
1D1
47
2
1D
24
25
C1
1Q1
2D1
36
1D
13
2Q1
To Seven Other Channels
To Seven Other Channels
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±24 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±24 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±260 mA
Maximum power dissipation at TA = 55°C (in still air) (see Note 2): DL package . . . . . . . . . . . . . . . . . . . 1.2 W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT16373Q-EP
16-BIT D-TYPE TRANSPARENT LATCH
WITH 3-STATE OUTPUTS
SCAS678B – MAY 2002 – REVISED JULY 2002
recommended operating conditions (see Note 3)
MIN
MAX
4.5
5.5
VCC
VIH
Supply voltage (see Note 4)
VIL
VI
Low-level input voltage
Input voltage
0
VO
IOH
Output voltage
0
IOL
Dt/Dv
Low-level output current
High-level input voltage
2
V
V
High-level output current
Input transition rise or fall rate
UNIT
0
0.8
V
VCC
VCC
V
–16
mA
V
16
mA
10
ns/V
TA
Operating free-air temperature
–40
125
°C
NOTES: 3. Unused inputs should be tied to VCC through a pullup resistor of approximately 5 kW or greater to prevent them from floating. Refer
to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4. All VCC and GND pins must be connected to the proper-voltage power supply.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
50 mA
IOH = –50
VOH
VOL
II
IOZ
ICC
DICC‡
Ci
IOH = –16
16 mA
MIN
TA = 25°C
TYP
MAX
MIN
4.5 V
4.4
4.4
5.5 V
5.4
5.4
4.5 V
3.94
3.7
5.5 V
4.94
4.7
MAX
V
IOH = –24 mA†
5.5 V
IOL = 50 mA
4.5 V
0.1
0.1
5.5 V
0.1
0.1
4.5 V
0.36
0.5
5.5 V
0.36
0.5
IOL = 16 mA
IOL = 24 mA{
VI = VCC or GND
VO = VCC or GND
VI = VCC or GND,
One input at 3.4 V,
3.85
5.5 V
IO = 0
Other inputs at GND or VCC
VI = VCC or GND
VI = VCC or GND
UNIT
V
0.5
5.5 V
±0.1
±1
5.5 V
±0.5
±10
5.5 V
8
160
mA
mA
mA
5.5 V
0.9
1
mA
5V
4.5
pF
Co
5V
12
† Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms.
‡ This is the increase in supply current for each input that is at one of the specified TTL-voltage levels rather than 0 V to VCC.
pF
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
TA = 25°C
MIN
MAX
MIN
MAX
UNIT
tw
tsu
Pulse duration, LE high
4
4
ns
Setup time, data before LE↓
1
1
ns
th
Hold time, data after LE↓
5
5
ns
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN74ACT16373Q-EP
16-BIT D-TYPE TRANSPARENT LATCH
WITH 3-STATE OUTPUTS
SCAS678B – MAY 2002 – REVISED JULY 2002
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
D
Q
tPLH
tPHL
LE
Q
tPZH
tPZL
OE
Q
tPHZ
tPLZ
OE
Q
MIN
TA = 25°C
TYP
MAX
MIN
MAX
3.8
7.9
9.4
3.8
11.8
3.1
8.2
9.7
3.1
13
4.6
9.3
10.8
4.6
13.7
4.5
9.1
10.5
4.5
13
3.1
8
9.5
3.1
13
3.8
9.4
11.1
3.8
15.1
5.3
8.6
9.9
5.3
11
4.3
7.4
8.7
4.3
9.8
UNIT
ns
ns
ns
ns
operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
Cpd
d
4
Power dissipation capacitance per latch
POST OFFICE BOX 655303
TEST CONDITIONS
Outputs enabled
Outputs disabled
• DALLAS, TEXAS 75265
CL = 50 pF,
pF
f = 1 MHz
TYP
43
4.5
UNIT
pF
SN74ACT16373Q-EP
16-BIT D-TYPE TRANSPARENT LATCH
WITH 3-STATE OUTPUTS
SCAS678B – MAY 2002 – REVISED JULY 2002
PARAMETER MEASUREMENT INFORMATION
2 × VCC
S1
500 Ω
From Output
Under Test
Open
GND
500 Ω
CL = 50 pF
(see Note A)
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
GND
LOAD CIRCUIT
3V
1.5 V
Timing Input
0V
tw
tsu
3V
1.5 V
Input
th
1.5 V
3V
1.5 V
1.5 V
Data Input
0V
0V
VOLTAGE WAVEFORMS
VOLTAGE WAVEFORMS
Output
Control
(low-level
enabling)
3V
Input
1.5 V
1.5 V
0V
In-Phase
Output
50% VCC
50% VCC
tPLZ
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
VOH
50% VCC
VOL
50% VCC
Output
Waveform 2
S1 at GND
(see Note B)
VOLTAGE WAVEFORMS
≈VCC
20% VCC
VOL
tPHZ
tPZH
tPLH
tPHL
Out-of-Phase
Output
VOH
50% VCC
VOL
1.5 V
0V
tPZL
tPHL
tPLH
3V
1.5 V
50% VCC
80% VCC
VOH
≈0 V
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 3 ns, tf = 3 ns.
D. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
PACKAGE OPTION ADDENDUM
www.ti.com
7-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN74ACT16373QDLREP
ACTIVE
SSOP
DL
48
1000
None
Call TI
Level-1-235C-UNLIM
V62/03602-01XE
ACTIVE
SSOP
DL
48
1000
None
Call TI
Level-1-235C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated
Similar pages