NAIS ACV12012 Automotive low profile micro-iso/micro-280 relay Datasheet

cv.fm
1
y [ W
Q O O P N P Q
P P œ @ ˛ j œ @
ª R
Q Q “
CV
AUTOMOTIVE LOW PROFILE
MICRO-ISO/MICRO-280
RELAY
CV-RELAYS
FEATURES
Micro ISO 1c type
• Low profile:
22.5 mm(L)×15 mm(W)×15.7 mm(H)
.886 inch(L)×.591 inch(W)×.618 inch(H)
• Low temperature rise
Terminal temperature has been reduced
compared with using our conventional
product
• Low sound pressure level
Noise level has been reduced
approx.10dB compared with using our
conventional product.
Micro ISO 1a type
• Wide line-up
Micro ISO/Micro 280 terminal types and
resistor and diode inside type, PCB
terminal type (Micro 280 only).
• Plastic sealed type
Plastically sealed for automatic cleaning.
Micro 280 plug-in type Micro 280 PCB type
SPECIFICATIONS
Contact
Characteristics
Arrangement
Contact material
Initial contact resistance,
max. (By voltage drop 6 V
DC 1 A)
Initial contact voltage drop,
max.
Rating
Nominal
switching
capacity
Max. carrying
current
(14 V DC,
at 85°C 185°F)
Mechanical
(at 120 cpm)
Expected
life (min.
operation) Electrical
(at rated load)
1 Form A
1 Form C
Silver alloy
N.O.: 0.2 V
(at 20 A switching)
N.O.: 0.2 V
(at 20 A switching)
N.C.: 0.5 V
(at 10 A switching)
N.O.: 20 A 14 V DC
N.O.: 20 A 14 V DC
N.C.: 10 A 14 V DC
N.O.: 20 A
N.C.: 10 A
Min. 20MΩ
(at 500 V DC)
Initial
breakdown
voltage *3
Between open contacts
500 Vrms for 1min.
Between contacts and coil
500 Vrms for 1min.
Operate time *4
(at nominal voltage) (at 20°C 68°F)
Release time (without diode) *4
(at nominal voltage) (at 20°C 68°F)
Functional *5
Shock resistance
Destructive *6
Functional *7
Vibration resistance
Destructive *8
Min. 106
Min. 105*1
Remarks
*
*1
*2
*3
*4
*5
*6
*7
*8
15cpm
Initial insulation resistance *2
50mΩ
N.O.: 20 A
Max. operating speed
(at nominal switching capacity)
Specifications will vary with foreign standards certification ratings.
At nominal switching capacity, operating frequency: 2s ON, 2s OFF
Measurement at same location as “Initial breakdown voltage” section.
Detection current: 10mA
Excluding contact bounce time.
Half-wave pulse of sine wave: 11 ms; detection time: 10 µs
Half-wave pulse of sine wave: 6 ms
Detection time: 10 µs
Time of vibration for each direction;
X, Y, Z direction: 4 hours
Y
X
Conditions in case of
Ambient
operation, transport and
temp*10
9
storage *
(Not freezing and condensing
Humidity
at low temperature)
Unit weight
Max. 10ms
Max. 10ms
Min. 100 m/s2{10 G}
Min. 1,000 m/s2{100 G}
10 to 100 Hz,
Min.44.1 m/s2 {4.5 G}
10 to 500 Hz,
Min.44.1 m/s2 {4.5 G}
–40 to +85°C
–40 to +185°F
25 to 85% R.H.
Approx. 15.0g .53 oz
Z
*9 Refer to 5. Usage, transport and storage condition mentioned in NOTES
*10 Ambient temperature 125°C 257°F type is also available. Please contact us for
details.
TYPICAL APPLICATIONS
Automotive system
Condenser fan, Wiper, Defogger, Magnet clutch, Radiator fan,
Foglamp, Auto cruise control, Horn, Heater, Air Compressor
1
cv.fm
2
y [ W
Q O O P N P Q
P P œ @ ˛ j œ @
ª R
Q Q “
CV
ORDERING INFORMATION
Ex.
A
CV
1
2
0
12
Product name
Contact arrangement
Mounting classification
Type classification
Coil voltage, V DC
CV
1: 1 Form C
3: 1 Form A
1: Micro ISO plug-in type
2: Micro 280 plug-in type
3: Micro 280 PC board type
0: Standard type
1: With diode inside
2: With resistor inside
12: 12
Note: Standard packing; Carton (Tube): 50 pcs.; Case: 200 pcs.
TYPES
1. Micro ISO terminal type
Coil voltage (DC)
Contact arrangement
Mounting classification
1 Form A
12 V
Plug-in terminal
1 Form C
Type classification
Standard type
With diode inside type
With resistor inside type
Standard type
With diode inside type
With resistor inside type
Part No.
ACV31012
ACV31112
ACV31212
ACV11012
ACV11112
ACV11212
Type classification
Standard type
With diode inside type
With resistor inside type
Standard type
With diode inside type
With resistor inside type
Standard type
With diode inside type
With resistor inside type
Standard type
With diode inside type
With resistor inside type
Part No.
ACV32012
ACV32112
ACV32212
ACV33012
ACV33112
ACV33212
ACV12012
ACV12112
ACV12212
ACV13012
ACV13112
ACV13212
2. Micro 280 terminal type
Coil voltage (DC)
Contact arrangement
Mounting classification
Plug-in terminal
1 Form A
PC board terminal
12 V
Plug-in terminal
1 Form C
PC board terminal
COIL DATA (at 20°C 68°F)
Nominal voltage,
V DC
12
Pick-up voltage,
* V DC (max.)
(Initial)
7.0
Drop-out voltage,
Coil resistance,
Nominal operating current,
V DC (min.)
Ω(±10%)
mA (±10%)
(Initial)
180
67
0.6
142.3 (with resistor)
100 (with resistor)
Nominal operating
power, W
0.8
1.0 (with resistor)
Usable voltage
range, V DC
10 to 16
* Other pick-up voltage types are also available. Please contact us for details.
DIMENSIONS
mm inch
1. Micro ISO terminal type
Schematic (Bottom view)
1 Form A
15.7
.618
1 Form C
2
2
5
3
5
4
11
.433
4.8
.189
0.8
.031
22.5
.886
6
8
.236 .315
9
.354
Sealed by epoxy resin
*A
6.3
.248
15
.591
1
Including diode type,
including resistor type also available
0.8
.031
3.25
.128
Dimension:
Max. 1mm .039 inch:
1 to 3mm .039 to .118 inch:
Min. 3mm .118 inch:
Tolerance
±0.1 ±.004
±0.2 ±.008
±0.3 ±.012
* Dimensions (thickness and width) of terminal specified in this catalog is measured before pre-soldering.
Intervals between terminals is measured at A surface level.
2
1
3
3
y [ W
Q O O P N P Q
P P œ @ ˛ j œ @
ª R
Q Q “
CV
2. Micro 280 terminal type
1). Plug-in type
mm inch
Schematic (Bottom view)
1 Form A
15.7
.618
11
.433
2.8
.110
22.5
.886
16.2
.638
7.8
.307
87 87a
86
Dimension:
Max. 1mm .039 inch:
1 to 3mm .039 to .118 inch:
Min. 3mm .118 inch:
85
30
1 Form C
87
85
87
86
30
86
87A
85
30
Including diode type,
including resistor type also available
0.8
.031
15
.591
*A
Sealed by epoxy resin
Tolerance
±0.1 ±.004
±0.2 ±.008
±0.3 ±.012
* Dimensions (thickness and width) of terminal specified in this catalog is measured before pre-soldering.
Intervals between terminals is measured at A surface level.
2). PC board type
Schematic (Bottom view)
1 Form A
16.7 1
.657 .039
3.5
.138
*A
1
.039
22.5
.886
2.8
.110
0.8
.031
15
.591
1 Form C
87
85
87
86
30
86
87A
85
30
Including diode type,
including resistor type also available
16.2
.638
7.8
.307
87 87a
86
Dimension:
Max. 1mm .039 inch:
1 to 3mm .039 to .118 inch:
Min. 3mm .118 inch:
85
30
Sealed by epoxy resin
Tolerance
±0.1 ±.004
±0.2 ±.008
±0.3 ±.012
* Dimensions (thickness and width) of terminal specified in this catalog is measured before pre-soldering.
Intervals between terminals is measured at A surface level.
REFERENCE DATA
2-(1). Electrical life test (Motor load)
Tested sample: ACV11212
Quantity: n = 3
Load: Inrush 30A, Steady 14A, 13.5V DC
Ambient temperature: Room temperature
Operating frequency: ON 12s, OFF 14s
180
10
Pick-up and drop-out voltage, V
1. Coil temperature rise
Point measured: Inside the coil
Contact carrying current: 20A
Coil applied voltage: 13.5V
Temperature rise, °C
150
20A
Circuit:
120
Tested sample
90
60
M
30
0
M
Contact welding: 0 times
Miscontact: 0 times
8
6
Pick-up voltage
Max.
X
Min.
Drop-out voltage
Max.
X
Min.
4
2
13.5 V DC
0
55
65
75
85
Ambient temperature, °C
0
10
No. of operations, × 104
2-(2). Electrical life (Motor load)
Tested sample: ACV31212
Quantity: n = 3
Load: Inrush 65A, Steady 14A, 14V DC
Operating frequency: ON 2s, OFF 6s
Ambient temperature: Room temperature
Circuit:
Tested sample
14 V DC
M
Motor
120W
10
Pick-up and drop-out voltage, V
cv.fm
Contact welding: 0 times
Miscontact: 0 times
8
Pick-up voltage
Max.
X
Min.
6
4
Drop-out voltage
Max.
X
Min.
2
0
0
10
No. of operations, × 104
3
cv.fm
4
y [ W
Q O O P N P Q
P P œ @ ˛ j œ @
ª R
Q Q “
CV
2-(3). Electrical life (Lamp load)
Circuit:
Tested sample
10
Pick-up and drop-out voltage, V
Tested sample: ACV31212
Quantity: n = 5
Load: 120W, Inrush 80A, Steady 10A, 14V DC
Operating frequency: ON 2s, OFF 13s
Ambient temperature: Room temperature
Contact welding: 0 times
Miscontact: 0 times
8
Pick-up voltage
Max.
X
Min.
6
4
Drop-out voltage
Max.
X
Min.
2
120W
0
0
10
No. of operations, × 104
NOTES
12/1/2001
4
5. Usage, transport and storage
conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +85°C –40 to +185°F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
Humidity, %R.H.
,,,,,,,
,
,
,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
,,,,,,,,,,,,
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be rectangular.
If it includes ripple, the ripple factor should
be less than 5%. However, check it with
the actual circuit since the characteristics
may be slightly different.
2. Voltage applied to coil
To ensure reliable operation, please apply
nominal voltage to the coil. Beware of the
fact that pick-up voltage and drop-out
voltage vary depending on the ambient
temperature and conditions.
3. Operating life
Operating life varies depending on the
type and load of the coil drive circuit, as
well as factors like the operating
frequency, operating phase and ambient
atmosphere, so please check with actual
equipment.
4.Soldering
We recommend the following soldering
conditions.
1) Automatic soldering
* Preheating: 100°C 212°F, within 2 mins
(PC board solder surface)
* Soldering: 260°C 500°F, within 5 s
2) Hand soldering
* Iron tip temperature: 280 to 300°C 536
to 571°F
* Soldering iron: 30 to 60W
* Soldering time: Within 5 s
85
Tolerance range
(Avoid freezing when (Avoid
used at temperatures condensation when
lower than 0°C 32°F) used at temperatures
higher than 0°C 32°F)
5
–40
–40
0
+32
Temperature, °C °F
3) Freezing
Condensation or other moisture may
freeze on the relay when the
temperatures are lower than 0°C 32°F.
This causes problems such as sticking of
movable parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
6. Others
1) If in error the relay has been dropped,
the appearance and characteristics
should be checked before use without fail.
2) Please do not use the coating material
of organic system which contains solvents
such as xylene and toluene for this
product.
+85
+185
(3) Atmospheric pressure: 86 to 106 kPa
2) Condensation
Condensation forms when there is a
sudden change in temperature under high
temperature and high humidity conditions.
Condensation will cause deterioration of
the relay insulation.
All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog
Similar pages