AD AD7394 3 v, dual, serial input 12-/10-bit dac Datasheet

a
APPLICATIONS
Automotive Output Span Voltage
Portable Communications
Digitally Controlled Calibration
PC Peripherals
GENERAL DESCRIPTION
The AD7394/AD7395 family of dual, 12-/10-bit, voltage output
digital-to-analog converters is designed to operate from a single
+3 V supply. Built using a CBCMOS process, this monolithic
DAC offers the user low cost and ease of use in single-supply
+3 V systems. Operation is guaranteed over the supply voltage
range of +2.7 V to +5.5 V making this device ideal for battery
operated applications.
The full-scale output voltage is determined by the applied external reference input voltage, VREF. The rail-to-rail VREF input
to VOUT outputs allows for a full-scale voltage set equal to the
positive supply VDD or any value in between.
A doubled-buffered serial data interface offers high speed,
microcontroller compatible inputs using serial-data-in (SDI),
clock (CLK) and load strobe (LDA + LDB) pins. A chip-select
(CS) pin simplifies connection of multiple DAC packages by
enabling the clock input when active low. Additionally, an RS
input sets the output to zero scale or to 1/2 scale based on the
logic level applied to the MSB pin. The power shutdown pin,
SHDN, reduces power dissipation to nanoamp current levels.
All digital inputs contain Schmitt-triggered logic levels to minimize power dissipation and prevent false triggering on the clock
input.
Both parts are offered in the same pinout to allow users to select
the amount of resolution appropriate for their application without circuit card redesign.
FUNCTIONAL BLOCK DIAGRAM
VDD VREF
CS
OP
AMP A
R
E
D G
A I
C S
T
A E
R
EN
CLK
DAC A
VOUTA
D
SDI
(DATA)
S
H
I
F
T
R
E
G
I
S
T
E
R
P R
12
AD7394/AD7395
LDA
R
E
D G
A I
C S
T
B E
R
LDB
P R
D
DGND
MSB
OP
AMP B
DAC B
RS
VOUTB
SHDN
AGND
The AD7394/AD7395 is specified over the extended industrial
(–40°C to +85°C) temperature range. Packages available include plastic DIP and low profile 1.75 mm height SO-14 surface
mount packages. The AD7395ARU is available for ultracompact
applications in a thin 1.1 mm TSSOP-14 package. For automotive
applications the AD7395AR is specified for operation over the
(–40°C to +125°C) temperature range.
1
VDD = 3V
VREF = 2.5V
0.8
0.6
0.4
DNL – LSB
FEATURES
Micropower: 100 mA/DAC
0.1 mA Typical Power Shutdown
Single-Supply +2.7 V to +5.5 V Operation
Compact 1.1 mm Height TSSOP-14 Package
AD7394/12-Bit Resolution
AD7395/10-Bit Resolution
Serial Interface with Schmitt Trigger Inputs
+3 V, Dual, Serial Input
12-/10-Bit DACs
AD7394/AD7395
0.2
0
–0.2
–0.4
–0.6
TA = –558C, +258C, +858C
SUPERIMPOSED
–0.8
–1
0
500
1000
1500
2000 2500
CODE – Decimal
3000
3500
4000
Figure 1. Differential Nonlinearity Error vs. Code
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1998
AD7394/AD7395–SPECIFICATIONS
AD7394 12-BIT RAIL-TO-RAIL VOLTAGE OUT DAC
ELECTRICAL CHARACTERISTICS (@ V = 2.5 V, –408C < T < +858C, unless otherwise noted)
REF IN
A
Parameter
Symbol
Conditions
3 V 6 10%
5 V 6 10%
Units
STATIC PERFORMANCE
Resolution1
Relative Accuracy2
Relative Accuracy2
Differential Nonlinearity2
Differential Nonlinearity2
Zero-Scale Error
Full-Scale Voltage Error
Full-Scale Voltage Error
Full-Scale Tempco3
N
INL
INL
DNL
DNL
VZSE
VFSE
VFSE
TCVFS
TA = +25°C
TA = –40°C, +85°C
TA = +25°C, Monotonic
Monotonic
Data = 000H
TA = +25°C, +85°C, Data = FFFH
TA = –40°C, Data = FFFH
12
± 1.5
± 2.0
± 0.9
±1
4.0
±8
± 20
–30
12
± 1.5
± 2.0
± 0.9
±1
4.0
±8
± 20
–30
Bits
LSB max
LSB max
LSB max
LSB max
mV max
mV max
mV max
ppm/°C typ
REFERENCE INPUT
VREF IN Range
Input Resistance
Input Capacitance3
VREF
RREF
CREF
0/VDD
2.5
5
0/VDD
2.5
5
V min/max
MΩ typ4
pF typ
ANALOG OUTPUT
Output Current (Source)
Output Current (Sink)
Capacitive Load3
IOUT
IOUT
CL
1
3
100
1
3
100
mA typ
mA typ
pF typ
LOGIC INPUTS
Logic Input Low Voltage
Logic Input High Voltage
Input Leakage Current
Input Capacitance3
VIL
VIH
IIL
CIL
0.5
VDD–0.6
10
10
0.8
4.0
10
10
V max
V min
µA max
pF max
INTERFACE TIMING3, 5
Clock Width High
Clock Width Low
Load Pulsewidth
Data Setup
Data Hold
Clear Pulsewidth
Load Setup
Load Hold
tCH
tCL
tLDW
tDS
tDH
tCLRW
tLD1
tLD2
50
50
30
10
30
15
30
40
30
30
20
10
15
15
15
20
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
AC CHARACTERISTICS
Output Slew Rate
Settling Time6
DAC Glitch
Digital Feedthrough
Feedthrough
SR
tS
Q
Q
VOUT/VREF
0.05
70
65
15
0.05
60
65
15
V/µs typ
µs typ
nV/s typ
nV/s typ
VREF = 1.5 VDC +1 V p-p,
Data = 000H, f = 100 kHz
–63
–63
dB typ
DNL < ± 1 LSB
SHDN = 0, VIL = 0 V, No Load
VIL = 0 V, No Load
VIL = 0 V, No Load
∆VDD = ± 5%
2.7/5.5
0.1/1.5
125/200
600
0.006
2.7/5.5
0.1/1.5
125/200
1000
0.006
V min/max
µA typ/max
µA typ/max
µW max
%/% max
SUPPLY CHARACTERISTICS
Power Supply Range
Shutdown Supply Current
Positive Supply Current
Power Dissipation
Power Supply Sensitivity
VDD RANGE
IDD_SD
IDD
PDISS
PSS
Data = 800H, ∆VOUT = 5 LSB
Data = 800H, ∆VOUT = 5 LSB
No Oscillation
Data = 000H to FFFH to 000H
To ± 0.1% of Full Scale
Code 7FFH to 800H to 7FFH
NOTES
1
One LSB = V REF/4096 V for the 12-bit AD7394.
2
The first two codes (000 H, 001H) are excluded from the linearity error measurement.
3
These parameters are guaranteed by design and not subject to production testing.
4
Typicals represent average readings measured at +25°C.
5
All input control signals are specified with t R = tF = 2 ns (10% to 90% of +3 V) and timed from a voltage level of 1.6 V.
6
The settling time specification does not apply for negative going transitions within the last three LSBs of ground.
Specifications subject to change without notice.
–2–
REV. 0
AD7394/AD7395
AD7395 10-BIT RAIL-TO-RAIL VOLTAGE OUT DAC
ELECTRICAL CHARACTERISTICS (@ V = 2.5 V, –408C < T < +858C/+1258C, unless otherwise noted)
REF IN
Parameter
Symbol
STATIC PERFORMANCE
Resolution1
Relative Accuracy2
Relative Accuracy2
Differential Nonlinearity2
Zero-Scale Error
Full-Scale Voltage Error
N
INL
INL
DNL
VZSE
VFSE
Full-Scale Voltage Error
Full-Scale Tempco3
VFSE
TCVFS
A
Conditions
TA = +25°C
TA = –40°C, +85°C, +125°C
Monotonic
Data = 000H
TA = +25°C, +85°C, +125°C
Data = FFFH
TA = –40°C, Data = FFFH
3 V 6 10%
5 V 6 10%
Units
10
± 1.5
± 2.0
±1
9.0
10
± 1.5
± 2.0
±1
9.0
Bits
LSB max
LSB max
LSB max
mV max
± 42
± 48
–35
± 42
± 48
–35
mV max
mV max
ppm/°C typ
0/VDD
2.5
5
0/VDD
2.5
5
V min/max
MΩ typ4
pF typ
1
3
100
1
3
100
mA typ
mA typ
pF typ
REFERENCE INPUT
VREF IN Range
Input Resistance
Input Capacitance3
VREF
RREF
CREF
ANALOG OUTPUT
Output Current (Source)
Output Current (Sink)
Capacitive Load3
IOUT
IOUT
CL
LOGIC INPUTS
Logic Input Low Voltage
Logic Input High Voltage
Input Leakage Current
Input Capacitance3
VIL
VIH
IIL
CIL
0.5
VDD–0.6
10
10
0.8
4.0
10
10
V max
V min
µA max
pF max
INTERFACE TIMING3, 5
Clock Width High
Clock Width Low
Load Pulsewidth
Data Setup
Data Hold
Clear Pulsewidth
Load Setup
Load Hold
tCH
tCL
tLDW
tDS
tDH
tCLRW
tLD1
tLD2
50
50
30
10
30
15
30
40
30
30
20
10
15
15
15
20
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
AC CHARACTERISTICS
Output Slew Rate
Settling Time6
DAC Glitch
Digital Feedthrough
Feedthrough
SR
tS
Q
Q
VOUT/VREF
0.05
70
65
15
0.05
60
65
15
V/µs typ
µs typ
nV/s typ
nV/s typ
VREF = 1.5 VDC +1 V p-p,
Data = 000H, f = 100 kHz
–63
–63
dB typ
DNL < ± 1 LSB
SHDN = 0, VIL = 0 V, No Load
VIL = 0 V, No Load
VIL = 0 V, No Load
∆VDD = ± 5%
2.7/5.5
0.1/1.5
125/200
600
0.006
2.7/5.5
0.1/1.5
125/200
1000
0.006
V min/max
µA typ/max
µA typ/max
µW max
%/% max
SUPPLY CHARACTERISTICS
Power Supply Range
Shutdown Supply Current
Positive Supply Current
Power Dissipation
Power Supply Sensitivity
VDD RANGE
IDD_SD
IDD
PDISS
PSS
Data = 200H, ∆VOUT = 5 LSB
Data = 200H, ∆VOUT = 5 LSB
No Oscillation
Data = 000H to 3FFH to 000H
To ± 0.1% of Full Scale
Code 7FFH to 800H to 7FFH
NOTES
1
One LSB = VREF/4096 V for the 10-bit AD7395.
2
The first two codes (000 H, 001H) are excluded from the linearity error measurement.
3
These parameters are guaranteed by design and not subject to production testing.
4
Typicals represent average readings measured at +25°C.
5
All input control signals are specified with t R = tF = 2 ns (10% to 90% of +3 V) and timed from a voltage level of 1.6 V.
6
The settling time specification does not apply for negative going transitions within the last three LSBs of ground.
Specifications subject to change without notice.
REV. 0
–3–
AD7394/AD7395
SDI
D11 D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CLK
tCSH
tCSS
CS
tLD2
tLD1
LDA,B
tDS
tDH
SDI
tCL
CLK
tCH
tLDW
LDA,B
tCLRW
RS
VOUT
tS
FS
ZS
tS
61 LSB
ERROR BAND
Figure 2. Timing Diagram
SHDN
tSDR
IDD
Figure 3. Timing Diagram
Table I. Control Logic Truth Table
CS CLK
RS
MSB
SHDN
LDA/B
Serial Shift Register Function
DAC Register Function
H
L
L
L
L
L
↑+
H
X
L
H
↑+
↑+
H
L
X
H
H
H
H
H
H
H
H
X
X
X
X
X
X
X
X
H
H
H
H
H
H
H
H
H
H
H
H
L
L
H
↓–
No Effect
No Effect
No Effect
Shift-Register-Data Advanced One Bit
Shift-Register-Data Advanced One Bit
No Effect
No Effect
No Effect
H
X
X
X
X
X
X
X
X
X
X
X
H
L
↑+
L
↑+
X
X
H
H
L
L
X
H
H
H
H
H
L
L
X
H
X
H
X
No Effect
No Effect
No Effect
No Effect
No Effect
No Effect
Latched
Latched
Latched
Latched
Transparent
Transparent
Latched
Updated with Current Shift Register
Contents
Transparent
Loaded with 800H
Latched with 800H
Loaded with All Zeros
Latched All Zeros
No Affect
NOTES
1. ↑+ positive logic transition; ↓– negative logic transition; X Don’t Care
2. Do not clock in serial data while level sensitive inputs LDA or LDB are logic LOW.
–4–
REV. 0
AD7394/AD7395
Table II. AD7394 Serial Input Register Data Format, Data Is Loaded in MSB-First Format
MSB
AD7394
LSB
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Table III. AD7395 Serial Input Register Data Format, Data Is Loaded in MSB-First Format
MSB
AD7395
LSB
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
AD7395AR and AD7395AN Only . . . . . . –40°C to +125°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature
␣ ␣ N-14 (Soldering, 10 sec) . . . . . . . . . . . . . . . . . . . . . . +300°C
␣ ␣ R-14 (Vapor Phase, 60 sec) . . . . . . . . . . . . . . . . . . . . +215°C
␣ ␣ RU-14 (Infrared, 15 sec) . . . . . . . . . . . . . . . . . . . . . . +224°C
ABSOLUTE MAXIMUM RATINGS*
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +7 V
VREF to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD
Logic Inputs to GND . . . . . . . . . . . . . . . . . . . . . –0.3 V, +8 V
VOUT to GND . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V
IOUT Short Circuit to GND . . . . . . . . . . . . . . . . . . . . . 50 mA
Package Power Dissipation . . . . . . . . . . . . . (TJ max – TA)/θJA
Thermal Resistance θJA
14-Lead Plastic DIP Package (N-14) . . . . . . . . . . 103°C/W
14-Lead SOIC Package (R-14) . . . . . . . . . . . . . . . 158°C/W
14-Lead Thin Shrink Surface Mount (RU-14) . . . 180°C/W
Maximum Junction Temperature (TJ max) . . . . . . . . . . 150°C
*Stresses above those listed under Absolute Maximum Ratings may cause
permanent damage to the device. This is a stress rating only; functional operation
of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ORDERING GUIDE
Model
Res
(LSB)
Temperature
Range
Package
Description
Package
Options
AD7394AN
AD7394AR
AD7395AN
AD7395AR
AD7395ARU
12
12
10
10
10
–40°C to +85°C
–40°C to +85°C
–40°C to +125°C
–40°C to +125°C
–40°C to +85°C
14-Lead P-DIP
14-Lead SOIC
14-Lead P-DIP
14-Lead SOIC
14-Lead Thin Shrink Small Outline Package (TSSOP)
N-14
R-14
N-14
R-14
RU-14
The AD7394/AD7395 contains 709 transistors. The die size measures 70 mil × 99 mil.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD7394/AD7395 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper
ESD precautions are recommended to avoid performance degradation or loss of functionality.
REV. 0
–5–
WARNING!
ESD SENSITIVE DEVICE
AD7394/AD7395
PIN FUNCTION DESCRIPTIONS
Pin
No.
Name
Function
1
2
3
4
5
6
7
8
AGND
VOUTA
VREF
DGND
CS
CLK
SDI
LDA
9
RS
10
LDB
11
MSB
12
SHDN
13
14
VDD
VOUTB
Analog Ground.
DAC A Voltage Output.
DAC Reference voltage input terminal. Establishes DAC full-scale output voltage. Pin can be tied to VDD pin.
Digital Ground. Should be tied to analog GND.
Chip Select, active low input. Disables shift register loading when high. Does not effect LDA or LDB operation.
Clock input, positive edge clocks data into shift register, MSB data bit first.
Serial Data Input, input data loads directly into the shift register.
Load DAC register strobe, level sensitive active low. Transfers shift register data to DAC A register. Asynchronous active low input. See Control Logic Truth Table for operation.
Resets DAC register to zero condition or half-scale, depending on MSB pin logic level. Asynchronous active
low input.
Load DAC register strobe, level-sensitive active low. Transfers shift register data to DAC B register. Asynchronous active low input. See Control Logic Truth Table for operation.
Digital Input: Logic High presets DAC registers to half-scale 800H (sets MSB bit to one) when the RS pin is
strobed; Logic Low clears all DAC registers to zero (000H) when the RS pin is strobed.
Active low shutdown control input. Does not affect register contents as long as power is present on VDD. New
data can be loaded into the shift register and DAC register during shutdown. When device is powered up the
most recent data loaded into the DAC register will control the DAC output.
Positive power supply input. Specified range of operation +2.7 V to +5.5 V
DAC B Voltage Output.
PIN CONFIGURATIONS
14 VOUTB
AGND 1
VOUTA 2
VREF 3
13 VDD
AD7394
AD7395
12 SHDN
TOP VIEW 11 MSB
CS 5 (Not to Scale) 10 LDB
DGND 4
CLK 6
9
RS
SDI 7
8
LDA
–6–
REV. 0
Typical Performance Characteristics– AD7394/AD7395
1.5
50
25
VDD = 3V
VREF = 2.5V
TA = –558C
1
FREQUENCY
INL – LSB
0.5
0
40
FREQEUENCY
20
15
10
–0.5
AD7395
SS = 200 UNITS
TA = +258C
VDD = 2.7V
VREF = 2.5V
AD7394
SS = 200 UNITS
TA = +258C
VDD = 2.7V
VREF = 2.5V
30
20
TA = +258C, +858C
0
0
500 1000 1500 2000 2500 3000 3500 4000
CODE – Decimal
Figure 4. AD7394 Integral Nonlinearity Error vs. Code
35
AD7395
30
Figure 5. Total Unadjusted Error
Histogram
30
AD7394
25
TA = +258C
0.5
20
VDD = 5.0V
TA = +258C
CODE = 768H
INL – LSB
0.4
15
15
0.3
0.2
FULL SCALE ERROR
210
30
32
34
36
TEMPCO – ppm/8C
38
10
0 0.5
1
1.5
2 2.5 3 3.5
VREF – Volts
4
4.5
5
Figure 8. Integral Nonlinearity Error
vs. VREF
1.5
2 2.5 3 3.5
VREF – Volts
4
4.5
5
5
AD7394
4.5
135
IDD – mA
4
1
AD7394
VDD = 3V
130
6
0 0.5
Figure 9. Full-Scale Error vs. VREF
140
VDD = 5V
VREF = 2.5V
TA = +258C
8
215
0
40
LOGIC THRESHOLD – V
28
Figure 7. Full-Scale Output Tempco
Histogram
OUTPUT NOISE DENSITY – mV/ Hz
5
25
0.1
5
TOTAL UNADJUSTED
FULL SCALE ERROR
10
0
10
26
5
10
15
0
TOTAL UNAJUSTED ERROR – LSB
AD7394
20
0
–5
Figure 6. Total Unadjusted Error
Histogram
0.6
SS = 200,
VDD = 2.7V
VREF = 2.5V
TA = +858C TO –408C
25
FREQUENCY
0
0
1
23
22
21
TOTAL UNADJUSTED ERROR – LSB
FSE – LSB
–1.5
10
5
–1
VIN 3V TO 0V
125
VIN 0V TO 3V
120
115
110
4
VLOGIC FROM LOW TO HIGH
3.5
3
2.5
2
2
1.5
105
0
1
10
100
1k
10k
FREQUENCY – Hz
Figure 10. AD7394 Output Noise
Density vs. Frequency
REV. 0
100k
1
100
0
0.5
1
1.5
2
VIN – Volts
2.5
3
Figure 11. Supply Current vs. Logic
Input Voltage
–7–
VLOGIC FROM HIGH TO LOW
2
3
4
5
VDD – Volts
6
7
Figure 12. Logic Threshold vs. Supply Voltage
AD7394/AD7395
20
80
1800
TA = +258C
AD7394
1600
D
1000
C
800
B
600
50
40
VDD = 3.0V, 65%
30
20
400
A
16
12
10
6
4
2
0
0
0
10k
100k
1M
CLOCK FREQUENCY – Hz
10M
1
10
100
1k
FREQUENCY – Hz
10
0
10k
Figure 14. AD7394 Power Supply
Rejection vs. Frequency
9
8
1.257
VOUT – Volts
VDD = 5V
7
6
VDD = 3V
5
4
2
3
4
5 6
7
D VOUT – LSB
8
9
10
0
25
VDD = +5V
VREF = 2.5V
TA = +258C
CODE = 800H TO 7FFH
5mV/DIV
1.252
1.247
210
VDD = 5V
CODE = FFFH
215
220
225
230
235
3
2
1
Figure 15. AD7394 IOUT Sink Current
vs. ∆VOUT
1.262
VREF = 2.5V
CODE = 800H
VDD = 3V
8
10
1k
VDD = 5V
14
200
Figure 13. Supply Current vs. Clock
Frequency
CURRENT SOURCING – mA
CURRENT SINKING – mA
VDD = 5.0V, 65%
GAIN – dB
IDD – mA
1200
60
PSRR – dB
1400
VREF = 2.5V
CODE = 800H
18
70
A: IDD = 2.7V, CODE = 555H
B: IDD = 2.7V, CODE = 3FFH
C: VDD = 5.5V, CODE = 155H
D: VDD = 5.5V, CODE = 3FFH
240
1.242
245
1
0
210 29 28 27 26 25 24 23 22 21
D VOUT – LSB
250
1.237
0
Figure 16. AD7394 IOUT Source Current vs. ∆VOUT
TIME – 2ms/DIV
Figure 17. Midscale Transition
Performance
100
10k
1k
FREQUENCY – Hz
100k
Figure 18. AD7395 Reference Multiplying Bandwidth
1.4
NOMINAL CHANGE IN VOUT – mV
AD7394
1.2
1
CODE = FFFH
0.8
0.6
CODE = 000H
0.4
0.2
0
0
200
300
400
500
100
HOURS OF OPERATION – 1508C
600
Figure 19. Long-Term Drift Accelerated by Burn-In
–8–
REV. 0
AD7394/AD7395
OPERATION
AMPLIFIER SECTION
The AD7394 and AD7395 are a set of pin compatible, dual,
12-bit/10-bit digital-to-analog converters. These single-supply
operation devices consume less than 200 microamps of current
while operating from power supplies in the +2.7 V to +5.5 V
range, making them ideal for battery operated applications.
They contain a voltage-switched, 12-bit/10-bit, laser trimmed
digital-to-analog converter, rail-to-rail output op amps, two
DAC registers and a serial input shift register. The external
reference input has constant input resistance independent of the
digital code setting of the DAC. In addition, the reference input
can be tied to the same supply voltage as VDD, resulting in a
maximum output voltage span of 0 to VDD. The serial interface
consists of a serial data input (SDI), clock (CLK) and chip
select pin (CS) and two load DAC Register pins (LDA and
LDB). A reset (RS) pin is available to reset the DAC register to
zero scale or midscale, depending on the digital level applied to
the MSB pin. This function is useful for power-on reset or
system failure recovery to a known state. Additional power
savings are accomplished by activating the SHDN pin resulting
in a 1.5 µA maximum consumption sleep mode.
The internal DAC’s output is buffered by a low power consumption precision amplifier. The op amp has a 60 µs typical
settling time to 0.1% of full scale. There are slight differences in
settling time for negative slewing signals versus positive. Also,
negative transition settling time to within the last 6 LSBs of zero
volts has an extended settling time. The rail-to-rail output stage
of this amplifier has been designed to provide precision performance while operating near either power supply. Figure 20
shows an equivalent output schematic of the rail-to-rail-amplifier with its N-channel pull-down FETs that will pull an output
load directly to GND. The output sourcing current is provided
by a P-channel pull-up device that can source current to GND
terminated loads.
VDD
P-CH
VOUT
N-CH
D/A CONVERTER SECTION
The voltage switched R-2R DAC generates an output voltage
dependent on the external reference voltage connected to the
REF pin according to the following equation:
V OUT
V REF × D
=
2N
AGND
Figure 20. Equivalent Analog Output Circuit
The rail-to-rail output stage provides more than ± 1 mA of output current. The N-channel output pull-down MOSFET shown
in Figure 20 has a 35 Ω ON resistance, which sets the sink current capability near ground. In addition to resistive load driving
capability, the amplifier has also been carefully designed and
characterized for up to 100 pF capacitive load driving capability.
(1)
where D is the decimal data word loaded into the DAC register
and N is the number of bits of DAC resolution. In the case of
the 10-bit AD7395 using a 2.5 V reference, Equation 1 simplifies to:
V OUT =
2.5 × D
1024
REFERENCE INPUT
(2)
The reference input terminal has a constant input resistance
independent of digital code which results in reduced glitches on
the external reference voltage source. The high 2.5 MΩ input
resistance minimizes power dissipation within the AD7394/
AD7395 D/A converters. The VREF input accepts input voltages
ranging from ground to the positive supply voltage VDD. One of
the simplest applications, which saves an external reference
voltage source, is connection of the VREF terminal to the positive
VDD supply. This connection results in a rail-to-rail voltage
output span maximizing the programmed range. The reference
input will accept ac signals as long as they are kept within the
supply voltage range, 0 < VREF < VDD. The reference bandwidth
and integral nonlinearity error performance are plotted in the
Typical Performance Characteristics section (see Figures 8 and
18). The ratiometric reference feature makes the AD7394/AD7395
an ideal companion to ratiometric analog-to-digital converters
such as the AD7896.
Using Equation 2 the nominal midscale voltage at VOUT is
1.25 V for D = 512; full-scale voltage is 2.497 V. The LSB step
size is = 2.5 × 1/1024 = 0.0024 V.
For the 12-bit AD7394 operating from a 5.0 V reference Equation 1 becomes:
V OUT =
5.0 × D
4096
(3)
Using Equation 3 the AD7394 provides a nominal midscale
voltage of 2.50 V for D = 2048, and a full-scale output of
4.998 V. The LSB step size is = 5.0 × 1/4096 = 0.0012 V.
REV. 0
–9–
AD7394/AD7395
POWER SUPPLY
logic transitions when a standard CMOS logic interface or opto
isolators are used. The logic inputs SDI, CLK, CS, LDA, LDB,
RS, SHDN all contain the Schmitt trigger circuits.
The very low power consumption of the AD7394/AD7395 is a
direct result of a circuit design optimizing the use of a CBCMOS
process. By using the low power characteristics of CMOS for
the logic, and the low noise, tight matching of the complementary bipolar transistors, excellent analog accuracy is achieved.
One advantage of the rail-to-rail output amplifiers used in the
AD7394/AD7395 is the wide range of usable supply voltage.
The part is fully specified and tested for operation from +2.7 V
to +5.5 V.
CS
EN
CLK
DAC A REGISTER
SDI
D
P
R
SHIFT
REGISTER
POWER SUPPLY BYPASSING AND GROUNDING
DAC B REGISTER
Local supply bypassing consisting of a 10 µF tantalum electrolytic in parallel with a 0.1 µF ceramic capacitor is recommended
in all applications (Figure 21).
Q
D
P
R
+2.7V TO +5.5V
*
C
REF
CS
VDD
AD7394
OR
AD7395
LDA, B
CLK
0.1mF
LDA LDB
10mF
Figure 23. Equivalent Digital Interface Logic
DIGITAL INTERFACE
VOUTA
VOUTB
SDI
RS
DGND
RS MSB
AGND
*OPTIONAL EXTERNAL
REFERENCE BYPASS
Figure 21. Recommended Supply Bypassing for the
AD7394/AD7395
INPUT LOGIC LEVELS
All digital inputs are protected with a Zener-type ESD protection structure (Figure 22) that allows logic input voltages to
exceed the VDD supply voltage. This feature can be useful if the
user is driving one or more of the digital inputs with a 5 V CMOS
logic input-voltage level while operating the AD7394/AD7395
on a +3 V power supply. If this mode of interface is used, make
sure that the VOL of the 5 V CMOS meets the VIL input requirement of the AD7394/AD7395 operating at 3 V. See Figure
12 for a graph of digital logic input threshold versus operating
VDD supply voltage.
VDD
LOGIC
IN
GND
Figure 22. Equivalent Digital Input ESD Protection
In order to minimize power dissipation from input logic levels
that are near the VIH and VIL logic input voltage specifications,
a Schmitt trigger design was used that minimizes the inputbuffer current consumption compared to traditional CMOS
input stages. Figure 11 is a plot of incremental input voltage
versus supply current showing that negligible current consumption takes place when logic levels are in their quiescent state.
The normal crossover current still occurs during logic transitions. A secondary advantage of this Schmitt trigger is the prevention of false triggers that would occur with slow moving
The AD7394/AD7395 has a serial data input. A functional
block diagram of the digital section is shown in Figure 23, while
Table I contains the truth table for the logic control inputs.
Three pins control the serial data input register loading. Two
additional pins determine which DAC will receive the data
loaded into the input shift register. Data at the SDI is clocked
into the shift register on the rising edge of the CLK. Data is
entered in the MSB-first format. The active low chip select (CS)
pin enables loading of data into the shift register from the SDI
pin. Twelve clock pulses are required to load the 12-bit AD7390
DAC shift register. If additional bits are clocked into the shift
register, for example, when a microcontroller sends two 8-bit
bytes, the MSBs are ignored (Table IV). The lowest resolution
AD7395 is also loaded MSB-first with 10 bits of data. Again, if
additional bits are clocked into the shift register only the last 10
bits clocked in are used. When CS returns to logic high, shiftregister loading is disabled. The load pins LDA and LDB control the flow of data from the shift register to the DAC register.
After a new value is clocked into the serial-input register, it will
be transferred to the DAC register associated with its LDA or
LDB logic control line. Note, if the user wants to load both
DAC registers with the current contents of the shift register,
both control lines LDA and LDB should be strobed together.
The LDA and LDB pins are level-sensitive and should be returned to logic high prior to any new data being sent to the
input shift register to avoid changing the DAC register values.
See Truth Table for complete set of conditions.
RESET (RS) PIN
Forcing the asynchronous RS pin low will set the DAC register
to all zeros, or midscale, depending on the logic level applied to
the MSB pin. When the MSB pin is set to logic high, both DAC
registers will be reset to midscale (i.e., the DAC Register’s MSB
bit will be set to Logic 1 followed by all zeros). The reset function is useful for setting the DAC outputs to zero at power-up or
after a power supply interruption. Test systems and motor
controllers are two of many applications that benefit from
powering up to a known state. The external reset pulse can be
–10–
REV. 0
AD7394/AD7395
Table IV. Typical Microcontroller Interface Formats
MSB
BYTE 1
B15
X
X
B14
X
X
B13
X
X
B12
X
X
B11
D11
X
B10
D10
X
B9
D9
D9
LSB
MSB
B8
D8
D8
B7
D7
D7
BYTE 0
B6
D6
D6
B5
D5
D5
B4
D4
D4
B3
D3
D3
LSB
B2
D2
D2
B1
D1
D1
B0
D0
D0
D11–D0: 12-bit AD7394 DAC data; D9–D0: 10-bit AD7395 DAC data; X = Don’t Care; The MSB of byte 1 is the first bit that is loaded into the SDI input.
generated by the microprocessor’s power-on RESET signal, by
an output from the microprocessor, or by an external resistor
and capacitor. RESET has a Schmitt trigger input which results
in a clean reset function when using external resistor/capacitor
generated pulses. See the Control-Logic Truth Table I.
POWER SHUTDOWN (SHDN)
Maximum power savings can be achieved by using the power
shutdown control function. This hardware activated feature is
controlled by the active low input SHDN pin. This pin has a
Schmitt trigger input which helps to desensitize it to slowly
changing inputs. By placing a logic low on this pin the internal
consumption of the device is reduced to nano amp levels, guaranteed to 1.5 µA maximum over the operating temperature
range. When the AD7394/AD7395 has been programmed into
the power shutdown state, the present DAC register data is
maintained as long as VDD remains greater than 2.7 V. Once a
wake-up command SHDN = 1 is given, the DAC voltage outputs will return to their previous values. It typically takes
80 microseconds for the output voltage to fully stabilize. In the
shutdown state the DAC output amplifier exhibits an opencircuit with a nominal output resistance of 500 kΩ to ground. If
the power shutdown feature is not needed, then the user should
tie the SHDN pin to the VDD voltage thereby disabling this
function.
UNIPOLAR OUTPUT OPERATION
This is the basic mode of operation for the AD7394. As shown
in Figure 24, the AD7394 has been designed to drive loads as
low as 5 kΩ in parallel with 100 pF. The code table for this
operation is shown in Table V.
+2.7V TO +5.5V
Table V. Unipolar Code Table
Hexadecimal
Number
in DAC Register
Decimal
Number
in DAC Register
Output
Voltage (V)
[VREF = 2.5 V]
FFF
801
800
7FF
000
4095
2049
2048
2047
0
2.4994
1.2506
1.2500
1.2494
0
The circuit can be configured with an external reference plus
power supply, or powered from a single dedicated regulator or
reference depending on the application performance requirements.
BIPOLAR OUTPUT OPERATION
Although the AD7395 has been designed for single-supply operation, the output can easily be configured for bipolar operation. A typical circuit is shown in Figure 25. This circuit uses a
clean regulated +5 V supply for power, which also provides the
circuit’s reference voltage. Since the AD7395 output span swings
from ground to very near +5 V, it is necessary to choose an
external amplifier with a common-mode input voltage range that
extends to its positive supply rail. The micropower consumption
OP196 has been designed just for this purpose and results in
only 50 microamps of maximum current consumption. Connection of the equally valued 470 kΩ resistors results in a differential amplifier mode of operation with a voltage gain of two,
which produces a circuit output span of ten volts, that is, –5 V to
+5 V. As the DAC is programmed from zero code 000H to midscale 200H to full-scale 3FFH, the circuit output voltage VO is
set at –5 V, 0 V and +5 V (–1 LSB). The output voltage VO is
coded in offset binary according to Equation 4.
R
0.1mF
0.01mF
 D  
V OUT = 
 –1 × 5
 512  
10mF
VDD
VREF
VOUTA
DAC A
75kV
100pF
75kV
100pF
EXT
REF
mC
5
VOUTB
DAC B
DIGITAL
DGND
AGND
DIGITAL INTERFACE
CIRCUITRY OMITTED
FOR CLARITY.
Figure 24. AD7394 Unipolar Output Operation
REV. 0
(4)
where D is the decimal code loaded in the AD7395 DAC register. Note that the LSB step size is 10/1024 = 10 mV. This circuit has been optimized for micropower consumption including
the 470 kΩ gain setting resistors, which should have low temperature coefficients to maintain accuracy and matching (preferably the same resistor material, such as metal film). If better
stability is required, the power supply could be substituted with
a precision reference voltage such as the low dropout REF195,
which can easily supply the circuit’s 262 microamps of current,
and still provide additional power for the load connected to
VOUT. The micropower REF195 is guaranteed to source 10 mA
–11–
AD7394/AD7395
ISY < 262mA
+5V
470kV
< 50mA
VO
AD7395
3FF
201
200
1FF
000
1023
513
512
511
0
4.9902
0.0097
0.0000
–0.0097
–5.0000
+5V
VDD
BIPOLAR
OUTPUT
SWING
OP196
C
Hexadecimal Number Decimal Number Analog Output
in DAC Register
in DAC Register Voltage (V)
470kV
200mA
REF
Table VI. Bipolar Code Table
C3323–8–4/98
output drive current, but consumes only 50 microamps internally. If higher resolution is required, the AD7394 can be used
with the addition of two more bits of data inserted into the
software coding, which would result in a 2.5 mV LSB step size.
Table VI shows examples of nominal output voltages, VO, provided by the Bipolar Operation circuit application.
VOUTA
–5V
GND
25V
ONLY ONE CHANNEL SHOWN.
DIGITAL INTERFACE CIRCUITRY
OMITTED FOR CLARITY.
Figure 25. Bipolar Output Operation
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Plastic DIP Package
(N-14)
Thin Surface Mount TSSOP Package
(RU-14)
0.795 (20.19)
0.725 (18.42)
0.201 (5.10)
0.193 (4.90)
14
8
1
7
PIN 1
0.280 (7.11)
0.240 (6.10)
0.060 (1.52)
0.015 (0.38)
0.210 (5.33)
MAX
14
0.325 (8.25)
0.300 (7.62) 0.195 (4.95)
0.115 (2.93)
0.177 (4.50)
0.169 (4.30)
0.256 (6.50)
0.246 (6.25)
1
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558)
0.014 (0.356)
0.015 (0.381)
0.008 (0.204)
0.100 0.070 (1.77) SEATING
(2.54) 0.045 (1.15) PLANE
BSC
8
7
PIN 1
0.006 (0.15)
0.002 (0.05)
SOIC Package
(R-14)
SEATING
PLANE
0.0433
(1.10)
MAX
0.0256
(0.65)
BSC
0.0118 (0.30)
0.0075 (0.19)
0.0079 (0.20)
0.0035 (0.090)
88
08
0.028 (0.70)
0.020 (0.50)
0.1574 (4.00)
0.1497 (3.80)
14
8
1
7
PIN 1
0.0098 (0.25)
0.0040 (0.10)
0.0500
SEATING (1.27)
PLANE BSC
PRINTED IN U.S.A.
0.3444 (8.75)
0.3367 (8.55)
0.2440 (6.20)
0.2284 (5.80)
0.0688 (1.75)
0.0532 (1.35)
0.0192 (0.49)
0.0138 (0.35)
0.0099 (0.25)
0.0075 (0.19)
0.0196 (0.50)
3 458
0.0099 (0.25)
88
08
0.0500 (1.27)
0.0160 (0.41)
–12–
REV. 0
Similar pages