AD AD767BD Microprocessor - compatible 12-bit d/a comverter Datasheet

AD767–SPECIFICATIONS (T = +258C, 615 volt power supplies, Unipolar Mode, unless otherwise noted.)
A
Model
AD767J/A/S1
Min
Typ
Max
DIGITAL INPUTS
Resolution
Logic Levels (TTL Compatible, TMIN–TMAX)3
VIH (Logic “1”)
+2.0
VIL (Logic “0”) J, K, A, B
0
0
VIL (Logic “0”) S
IIH (VIH = 5.5 V)
IIL (VIL = 0.8 V)
TRANSFER CHARACTERISTICS
ACCURACY
Linearity Error @ +25°C
TA = TMIN to TMAX
Differential Linearity Error @ +25°C
TA = TMIN to TMAX
Gain Error4
Unipolar Offset Error4
Bipolar Zero Error4
REFERENCE OUTPUT
External Current
TEMPERATURE RANGE
J/K
A/B
S
Operating
Storage (All Grades)
+5.5
+0.8
+0.7
10
5
+5.5
+0.8
+2.0
0
3
1
+2.0
0
3
1
10
5
12
Bits
+5.5
+0.8
V
V
V
µA
µA
10
5
±5
±1
± 15
±3
± 10
±5
±1
±5
± 30
±3
± 10
ppm of FSR/°C
ppm of FSR/°C
ppm of FSR/°C
3
2
1
4
3
3
2
1
4
3
3
2
1
4
3
µs
µs
µs
V/µs
10
10
± 2.5, ± 5, ± 10,
+5, +10
±5
0.05
10.10
5
5
10
10
9.90
0.1
± 12, ± 15
10.00
1.0
10.10
0.05
mA
Ω
mA
5
5
10
10
40
9.90
0.1
± 12, ± 15
616.5
9
18
400
V
40
10.00
1.0
611.4
± 2.5, ± 5, ± 10,
+5, +10
±5
0.05
40
0
–25
–55
–55
–65
LSB
LSB
LSB
LSB
% of FSR5
LSB
% of FSR
± 30
±3
± 10
±5
9.90
0.1
Units
±5
±1
±5
± 2.5, ± 5, ± 10,
+5, +10
POWER SUPPLY SENSITIVITY
VCC = +11.4 to +16.5 V dc
VEE = –11.4 to –16.5 V dc
POWER SUPPLY REQUIREMENTS
Rated Voltages
Range6
Supply Current
+11.4 to +16.5 V dc
–11.4 to –16.5 V dc
Total Power Consumption
3
1
12
10
ANALOG OUTPUT
Ranges6
Output Current
Output Impedance (dc)
Short-Circuit Current
12
AD767A2 Chips
Min
Typ
Max
± 1/2
61
± 1/8
61/2
± 1/2
61
± 1/2
61
± 1/4
61/2
± 1/2
61
± 1/2
61
± 1/4
61
± 1/2
61
Monotonicity Guaranteed Monotonicity Guaranteed Monotonicity Guaranteed
± 0.1
60.2
± 0.1
60.2
± 0.1
60.2
±1
62
±1
62
±1
62
± 0.05
60.1
± 0.05
60.1
± 0.05
60.1
DRIFT
Gain TA = 25°C to TMIN or TMAX
Unipolar Offset TA = 25°C to TMIN or TMAX
Bipolar Zero TA = 25°C to TMIN or TMAX
CONVERSION SPEED
Settling Time to ± 0.01% of FSR for
FSR change (2 kΩ||500 pF load)
with 10 kΩ Feedback
with 5 kΩ Feedback
For LSB Change
Slew Rate
Min
AD767K/B
Typ
Max
611.4
+70
+85
+125
+125
+125
0
–25
–55
–55
–65
10.10
V
mA
5
5
10
10
ppm of FS/%
ppm of FS/%
616.5
V
V
13
23
600
mA
mA
mW
± 12, ± 15
616.5
9
18
400
13
23
600
10.00
1.0
611.4
9
18
400
13
23
600
+70
+85
+125
+125
+125
–25
+85
–65
+125
°C
°C
°C
°C
°C
NOTES
1
AD767 “S” specifications shown for information only. Consult Analog Devices Military Databook or contact factory for a controlled specification sheet.
2
AD767A Chips specifications are tested at +25°C and, when in boldface, at +85°C. They are typical at –25°C.
3
The digital input specifications are 100% tested at +25°C, and guaranteed but not tested over the full temperature range.
4
Adjustable to zero.
5
FSR means “Full-Scale Range” and is 20 V for ± 10 V range and 10 V for the ± 5 V range.
6
A minimum power supply of ± 12.5 V is required for a ± 10 V full-scale output and ± 11.4 V is required for all other voltage ranges.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical test (except per Notes 1 and 2). Results from those tests are used to calculate
outgoing quality levels. All min and max specifications are guaranteed, although only those shown in boldface are tested on all production units.
–2–
REV. A
AD767
Ref Out, VOUT (Pins 6, 9) . . . Indefinite short to power ground
Momentary Short to VCC
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 mW
ABSOLUTE MAXIMUM RATINGS*
VCC to Power Ground . . . . . . . . . . . . . . . . . . . . .0 V to +18 V
VEE to Power Ground . . . . . . . . . . . . . . . . . . . . . 0 V to –18 V
Digital Inputs (Pins 11, 13–24)
to Power Ground . . . . . . . . . . . . . . . . . . . . –1.0 V to +7.0 V
Ref In to Reference Ground . . . . . . . . . . . . . . . . . . . . . . ± 12 V
Bipolar Offset to Reference Ground . . . . . . . . . . . . . . . . ± 12 V
10 V Span R to Reference Ground . . . . . . . . . . . . . . . . . ± 12 V
20 V Span R to Reference Ground . . . . . . . . . . . . . . . . . ± 24 V
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in
the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
TIMING SPECIFICATIONS
(All Models, TA = 25°C, VCC = +12 V or +15 V,
VEE = –12 V or –15 V)
Symbol
Parameter
Min Typ Max
tDS
Data Valid to End of CS
(–25°C to +85°C)
(–55°C to +125°C)
40
60
90
–
–
–
–
–
–
ns
ns
ns
tDH
Data Hold Tiıne
(–25°C to +85°C)
(–55°C to +125°C)
10
10
20
–
–
–
–
–
–
ns
ns
ns
tCS
CS Pulse Width
(–25°C to +85°C)
(–55°C to +125°C)
40
60
90
–
–
–
–
–
–
ns
ns
ns
tSETT
Output Voltage Settling Time* –
2
4
µs
*tSETT is measured referenced to the leading edge of t CS. If tCS > tDS, then
tSETT is measured referenced to the beginning of Data Valid.
PIN CONFIGURATION
DIP
PLCC
ORDERING GUIDE
Model1
Package
Linearity
Temperature Error Max
Range 8C
TMIN–TMAX
Gain T.C.
Max
ppm/8C
AD767JN
AD767JP
AD767KN
AD767KP
AD767AD
AD767BD
AD767SD/
883B
AD767A
Chips
Plastic DIP
PLCC
Plastic DIP
PLCC
Ceramic DIP
Ceramic DIP
0 to +70
0 to +70
0 to +70
0 to +70
–25 to +85
–25 to +85
± 1 LSB
± 1 LSB
± 1/2 LSB
± 1/2 LSB
± 1 LSB
± 1/2 LSB
30
30
15
15
30
15
Ceramic DIP
–55 to +125
Note 2
Note 2
N/A
–25 to +85
± 1 LSB
30
NOTES
1
D = Ceramic DIP; N = Plastic DIP; P = Plastic Leaded Chip Carrier.
2
For details on grade and package offerings screened in accordance with MIL-STD-883, refer to
the Analog Devices Military Products Databook or current AD767/883B data sheet.
REV. A
–3–
AD767
THE AD767 OFFERS TRUE 12-BIT PERFORMANCE
OVER THE FULL TEMPERATURE RANGE
LINEARITY ERROR: Analog Devices defines linearity error as
the maximum deviation of the actual, adjusted DAC output
from the ideal analog output (a straight line drawn from 0 to
F.S. – 1 LSB) for any bit combination. This is also referred to as
relative accuracy. The AD767 is laser trimmed to typically
maintain linearity errors at less than ± 1/8 LSB for the K and B
versions and ± 1/2 LSB for the J, A and S versions. Linearity
over temperature is also held to ± 1/2 LSB (K/B) or ± 1 LSB
(J/A/S).
Gain and offset drift are minimized in the AD767 because of the
thermal tracking of the scaling resistors with other device
components. Connections for various output voltage ranges are
shown in Table I.
MONOTONICITY: A DAC is said to be monotonic if the
output either increases or remains constant for increasing digital
inputs such that the output will always be a nondecreasing
function of input. All versions of the AD767 are monotonic over
their full operating temperature range.
DIFFERENTIAL NONLINEARITY: Monotonic behavior
requires that the differential linearity error be less than 1 LSB
both at +25°C as well as over the temperature range of interest.
Differential nonlinearity is the measure of the variation in analog
value, normalized to full scale, associated with a 1 LSB change
in digital input code. For example, for a 10 volt full-scale
output, a change of 1 LSB in digital input code should result in
a 2.44 mV change in the analog output (1 LSB = 10 V 3
1/4096 = 2.44 mV). If in actual use, however, a 1 LSB change
in the input code results in a change of only 0.61 mV (1/4 LSB)
in analog output, the differential nonlinearity error would be
–1.83 mV, or –3/4 LSB.
Figure 1. Output Amplifier Voltage Range Scaling Circuit
UNIPOLAR CONFIGURATION (Figure 2)
This configuration will provide a unipolar 0 to +10 volt output
range. In this mode, the bipolar offset terminal, Pin 4, should be
grounded if not used for trimming.
STEP I … ZERO ADJUST
Turn all bits OFF and adjust zero trimmer R1, until the output
reads 0.000 volts (1 LSB = 2.44 mV). In most cases this trim is
not needed, and Pin 4 should be connected to Pin 5.
STEP II … GAIN ADJUST
Turn all bits ON and adjust 100 Ω gain trimmer R2 until the
output is 9.9976 volts. (Full scale is adjusted to 1 LSB less than
nominal full scale of 10.000 volts.)
GAIN ERROR: DAC gain error is a measure of the difference
between an ideal DAC and the actual device’s output span. All
grades of the AD767 have a maximum gain error of 0.2% FS.
However, if this is not sufficient, the error can easily be adjusted
to zero (see Figures 2 and 3).
UNIPOLAR OFFSET ERROR: Unipolar offset error is a
combination of the offset errors of the voltage-mode DAC and
the output amplifier and is measured when the AD767 is
configured for unipolar outputs. It is present for all codes and is
measured with all “0s” in the DAC latches. This is easily
adjustable to zero when required.
BIPOLAR ZERO ERROR: Bipolar zero errors result from
errors produced by the DAC and output amplifier when the
AD767 is configured for bipolar output. Again, as with unipolar
offset and gain errors, this is easily adjusted to zero when
required.
Figure 2. 0 to +10 V Unipolar Voltage Output
ANALOG CIRCUIT CONNECTIONS
Internal scaling resistors provided in the AD767 may be connected
to produce bipolar output voltage ranges of ± 10, ± 5 or ±2.5 V
or unipolar output voltage ranges of 0 to +5 V or 0 to +10 V.
Table I. Output Voltage Range Connections
Output
Range
Digital
Input Codes
Connect
Pin 9 to
Connect
Pin 1 to
Connect
Pin 2 to
Connect
Pin 4 to
± 10 V
±5 V
± 2.5 V
0 to +10 V
0 to +5 V
Offset Binary
Offset Binary
Offset Binary
Straight Binary
Straight Binary
1
1 and 2
2
1 and 2
2
9
2 and 9
3
2 and 9
3
NC
1 and 9
9
1 and 9
9
6 (through 50 Ω fixed or 100 Ω trim resistor)
6 (through 50 Ω fixed or 100 Ω trim resistor)
6 (through 50 Ω fixed or 100 Ω trim resistor)
5 (or optional trim – See Figure 2)
5 (or optional trim – See Figure 2)
–4–
REV. A
AD767
The AD767 reference output should be buffered with an
external op amp if it is required to supply more than 0.1 mA
output current. The reference is typically trimmed to ± 0.2%,
then tested and guaranteed to ± 1.0% max error. The
temperature coefficient is comparable to that of the full-scale
TC for a particular grade.
BIPOLAR CONFIGURATION (Figure 3)
This configuration will provide a bipolar output voltage from
–5.000 to +4.9976 volts, with positive full scale occurring with
all bits ON (all 1s).
STEP I … OFFSET ADJUST
Turn OFF all bits. Adjust 100 Ω trimmer R1 to give –5.000
volts output.
If an external reference is used (10.000 V, for example),
additional trim range must be provided, since the internal
reference has a tolerance of ± 1%, and the AD767 full-scale and
bipolar offset are both trimmed with the internal reference. The
gain and offset trim resistors give about ± 0.25% adjustment
range, which is sufficient for the AD767 when used with the
internal reference.
STEP II … GAIN ADJUST
Turn ON all bits. Adjust 100 Ω gain trimmer R2 to give a
reading of +4.9976 volts.
STEP III … BIPOLAR ZERO ADJUST (Optional)
In applications where an accurate zero output is required, set
the MSB ON, all other bits OFF, and readjust R1 for zero volts
output.
It is also possible to use external references other than 10 volts.
The recommended range of reference voltage is from +8 to
+10.5 volts, which allows both 8.192 V and 10.24 V ranges to
be used. The AD767 is optimized for fixed-reference applications.
If the reference voltage is expected to vary over a wide range in
a particular application, a CMOS multiplying DAC is a better
choice.
Reduced values of reference voltage will also permit the ± 12 volt
± 5% power supply requirement to be relaxed to ± 12 volts
± 10%.
It is not recommended that the AD767 be used with external
feedback resistors to modify the scale factor. The internal
resistors are trimmed to ratio-match and temperature-track the
other resistors on the chip, even though their absolute tolerances
are ±20%, and absolute temperature coefficients are approximately
–50 ppm/°C. If external resistors are used, a wide trim range
(± 20%) will be needed and temperature drift will be increased
to reflect the mismatch between the temperature coefficients of
the internal and external resistors.
Figure 3. ± 5 V Bipolar Voltage Output
INTERNAL/EXTERNAL REFERENCE USE
The AD767 has an internal low-noise buried Zener diode
reference which is trimmed for absolute accuracy and temperature coefficient. This reference is buffered and optimized for use
in a high-speed DAC and will give long-term stability equal or
superior to the best discrete Zener reference diodes. The performance of the AD767 is specified with the internal reference
driving the DAC since all trimming and testing (especially for
full-scale error and bipolar offset) is done in this configuration.
Small resistors may be added to the feedback resistors in order
to accomplish small modifications in the scaling. For example, if
a 10.24 V full scale is desired, a 140 Ω 1% low-TC metal-film
resistor can be added in series with the internal (nominal) 5k
feedback resistor, and the gain trim potentiometer (between
Pins 6 and 7) should be increased to 200 Ω. In the bipolar
mode, increase the value of the bipolar offset trim potentiometer
also to 200 Ω.
The internal reference has sufficient buffering to drive external
circuitry in addition to the reference currents required for the
DAC (typically 0.5 mA to Ref In and 1.0 mA to Bipolar Offset).
A minimum of 0.1 mA is available for driving external loads.
Figure 4. Using the AD767 with the AD588 High Precision Reference
REV. A
–5–
AD767
USING THE AD767 WITH THE AD588 HIGH PRECISION
VOLTAGE REFERENCE
The AD767 is specified for gain drift from 15 ppm/°C to
30 ppm/°C (depending on grade) using its internal 10 volt
reference. Since the internal reference contributes the majority
of this drift, an external high-precision voltage reference will
greatly improve performance over temperature. As shown in
Figure 4, the 10 volt output from the AD588 is used as the
reference. With a 1.5 ppm/°C output voltage drift the AD588
contributes less than 1/2 LSB gain drift when used with the
AD767 over the industrial temperature range. Using this
combination may result in apparent increases in full-scale error
due to the differences between the internal reference by which
the device is laser trimmed and the external reference with
which the device is actually applied. The AD767 internal
reference is specified to be 10 volts ± 100 mV whereas the
AD588 is specified as 10 volts ± 1 mV. This may result in up to
101 mV of apparent full-scale error beyond the ± 25 mV
specified AD767 gain error. The 500 Ω potentiometer in series
with the reference input allows adequate trim range to null this
error.
Figure 5a. Large Scale Settling
Figures 5b and 5c show the settling time for the transition from
all bits on to all bits off. Note that the settling time to ± 1/2 LSB
for the 10 V step is improved from 2.4 microseconds to 1.6
microseconds by the addition of the 20 pF capacitor.
GROUNDING RULES
The AD767 brings out separate analog and power grounds to
allow optimum connections for low noise and high-speed
performance. These grounds should be tied together at one
point, usually the device power ground. The separate ground
returns are provided to minimize current flow in low-level signal
paths.
The analog ground at Pin 5 is the ground point for the output
amplifier and is thus the “high quality” ground for the AD767;
it should be connected directly to the analog reference point of
the system. The power ground at Pin 12 can be connected to
the most convenient ground point; analog power return is
preferred. If power ground contains high frequency noise
beyond 200 mV, this noise may feed through the converter, thus
some caution will be required in applying these grounds.
Figure 5b. Fine-Scale Settling, CF = 0 pF
It is also important to apply decoupling capacitors properly on
the power supplies for the AD767. The correct method for
decoupling is to connect a capacitor from each power supply pin
of the AD767 to the analog ground pin of the AD767. Any load
driven by the output amplifier should also be referred to the
analog ground pin.
OPTIMIZING SETTLING TIME
The dynamic performance of the AD767’s output amplifier can
be optimized by adding a small (20 pF) capacitor across the
feedback resistor. Figure 5 shows the improvement in both
large-signal and small-signal settling for the 10 V range. In
Figure 5a, the top trace shows the data inputs (DB11–DB0 tied
together), the second trace shows the CS pulse, and the lower
two traces show the analog outputs for CF = 0 and 20 pF
respectively.
Figure 5c. Fine-Scale Settling, CF = 20 pF
Figures 5d and 5e show the settling time for the transition from
all bits off to all bits on. The improvement in settling time
gained by adding CC = 20 pF is similar.
Figure 5d. Fine-Scale Settling, CF = 0 pF
–6–
REV. A
AD767
Figure 5e. Fine-Scale Settling, CF = 20 pF
Figure 6. 68000 – AD767 Interface
DIGITAL INPUT CONSIDERATIONS
8086 – AD767 INTERFACE
The threshold of the digital input circuitry is set at 1.4 volts and
does not change with supply voltage. Thus the AD767 digital
interface may be driven with any of the popular types of 5 volt
logic.
Interfacing the AD767 to the 8086 16-bit microprocessor
requires a minimal amount of external components. A 10 MHz
8086, for example, generates a 165 ns low write pulse which
may be gated with a decoded address to provide CS for the
AD767. As WR returns high valid data is latched into the DAC.
See Figure 7.
A good engineering practice is to connect unused inputs to
power ground to improve noise immunity. Unconnected data
and control inputs will float to logic 0 if left open.
The low digital input current of the AD767 eliminates the need
for buffer/drivers required by many monolithic converters using
bipolar technology. A single low-power Schottky gate, for
example, will drive several AD767s when connected to a
common bus.
INPUT CODING
The AD767 uses positive-true binary input coding. Logic “1” is
represented by an input voltage greater than 2.0 V, and logic
“0” is defined as an input voltage less than 0.8 V.
Unipolar coding is straight binary, where all zeroes (000H) on
the data inputs yields a zero analog output and all ones (FFFH)
yields an analog output 1 LSB below full scale.
Figure 7. 8086 – AD767 Interface
TMS32010 – AD767 INTERFACE
The high-speed digital interface of the AD767 facilitates its use
with the TMS32010 microprocessor at speeds up to 20 MHz.
In the three multiplexed LSBs of the address bus, PA2 – PA0
are decoded as a port address and OR’ed with the low write
enable to generate CS for the DAC. A simple OUT xx,y
instruction will output the data word stored in memory location
xx to any one of eight port locations y.
Bipolar coding is offset binary, where an input code of 000H
yields a minus full-scale output, an input of FFFH yields an
output 1 LSB below positive full scale, and zero occurs for an
input code with only the MSB on (800H).
The AD767 can be used with twos complement input coding if
an inverter is used on the MSB (DB11).
MICROPROCESSOR INTERFACE
The AD767, with its 40 ns minimum CS pulse width, may be
easily interfaced to any of today’s high-speed microprocessors.
The 12-bit single buffered input register will accept 12-bit
parallel data from processors such as the 68000, 8086, TMS320
series, and the Analog Devices ADSP-2100. Several illustrative
examples follow.
68000 – AD767 INTERFACE
Figure 6 illustrates the AD767 interface to a 68000 microprocessor. An active low decoded address is OR’ed with the
processor’s R/W signal to provide CS and latch data into the
AD767. Later in the bus cycle the processor issues the upper
(UDS) and lower (LDS) data strobes which are gated with the
decoded address to provide DTACK and terminate the bus
cycle. As shown, this interface will support a 12.5 MHz 68000
system.
REV. A
Figure 8. TMS32010 – AD767 Interface
TMS32020 – AD767 INTERFACE
Interfacing the AD767 to the TMS32020 microprocessor is
easily achieved by using the TMS32020 I/O port capability. The
IS signal distinguishes the I/O address space from the local
program/data memory space and is used to enable a 74LS138
decoder. The decoded port address is then gated with the R/W
and STRB signals to provide the AD767 CS.
–7–
C1068a–10–4/88
AD767
Figure 11. TMS320C25 – AD767 Interface
Figure 9. TMS32020 – AD767 Interface
ADSP-2100 – AD767 INTERFACE
OUTLINE DIMENSIONS
The ADSP-2100 single chip DSP processor may be interfaced
to the AD767 as shown in Figure 10. With a clock frequency of
32 MHz, and instruction execution in a single 125 ns cycle, the
processor will support the AD767 interface with a single wait
state.
Dimensions shown in inches and (mm).
24-Pin Ceramic (Suffix D)
24-Pin Plastic (Suffix N)
Figure 10. ADSP-2100 – AD767 Interface
The LOW decoded address is also gated with the Q output of a
D flip-flop to hold DMACK (Data Memory Acknowledge)
LOW. This forces the processor into a wait state and extends
the AD767 CS by 1 clock cycle. The rising edge of CLKOUT
latches Q HIGH bringing DMACK HIGH. The cycle is now
complete.
PRINTED IN U.S.A.
At the beginning of the data memory access cycle the processor
provides a 14-bit address on the DMA bus. The DMS signal is
then asserted enabling a LOW address decode. Valid data is
now placed on the data bus and DMWR is issued. DMWR is
OR’ed with the LOW address decode to generate the AD767
CS.
28-Pin PLCC (Suffix P)
TMS320C25 – AD767 INTERFACE
Figure 11 illustrates the AD767 interface to a TMS320C25
digital signal processor. Due to the high-speed capability of the
processor (40 MHz), a single wait state is required and is easily
generated using MSC. A 20 MHz TMS320C25 however, does
not require wait states and should be interfaced using the circuit
shown in Figure 9.
–8–
REV. A
Similar pages