AD AD7710ARZ-REEL7 Signal conditioning adc Datasheet

a
FEATURES
Charge Balancing ADC
24 Bits, No Missing Codes
ⴞ0.0015% Nonlinearity
2-Channel Programmable Gain Front End
Gains from 1 to 128
Differential Inputs
Low-Pass Filter with Programmable Filter Cutoffs
Ability to Read/Write Calibration Coefficients
Bidirectional Microcontroller Serial Interface
Internal/External Reference Option
Single- or Dual-Supply Operation
Low Power (25 mW Typ) with Power-Down Mode
(7 mW Typ)
Signal Conditioning ADC
AD7710
FUNCTIONAL BLOCK DIAGRAM
AVDD
DVDD
REF
REF
IN (–) IN (+)
REF OUT
2.5V REFERENCE
4.5␮A
CHARGE-BALANCING A/D
CONVERTER
AIN1(+)
AIN1(–)
M
U
X
AIN2(+)
AUTO-ZEROED
⌺-⌬
MODULATOR
PGA
DIGITAL
FILTER
SYNC
A = 1 – 128
AIN2(–)
AVDD
CLOCK
GENERATION
20␮A
APPLICATIONS
Weigh Scales
Thermocouples
Process Control
Smart Transmitters
Chromatography
VBIAS
AVDD
MCLK
IN
MCLK
OUT
SERIAL INTERFACE
CONTROL
REGISTER
IOUT
OUTPUT
REGISTER
AD7710
AGND DGND
VSS
RFS TFS MODE SDATA SCLK DRDY A0
GENERAL DESCRIPTION
The AD7710 is a complete analog front end for low frequency
measurement applications. The device accepts low level signals
directly from a strain gage or transducer and outputs a serial
digital word. It employs a sigma-delta conversion technique to
realize up to 24 bits of no missing codes performance. The input
signal is applied to a proprietary programmable gain front end
based around an analog modulator. The modulator output is
processed by an on-chip digital filter. The first notch of this
digital filter can be programmed via the on-chip control register,
allowing adjustment of the filter cutoff and settling time.
CMOS construction ensures low power dissipation, and a software programmable power-down mode reduces the standby
power consumption to only 7 mW typical. The part is available
in a 24-lead, 0.3 inch-wide, plastic and hermetic dual-in-line
package (DIP) as well as a 24-lead small outline (SOIC) package.
The part features two differential analog inputs and a differential reference input. Typically, one of the channels will be used
as the main channel with the second channel used as an auxiliary input to measure a second voltage periodically. It can be
operated from a single supply (by tying the VSS pin to AGND),
provided that the input signals on the analog inputs are more
positive than –30 mV. By taking the VSS pin negative, the part
can convert signals down to –VREF on its inputs. The AD7710
thus performs all signal conditioning and conversion for a singleor dual-channel system.
2. The AD7710 is ideal for microcontroller or DSP processor
applications with an on-chip control register that allows
control over filter cutoff, input gain, channel selection, signal
polarity, and calibration modes.
The AD7710 is ideal for use in smart, microcontroller based
systems. Input channel selection, gain settings, and signal polarity can be configured in software using the bidirectional serial
port. The AD7710 contains self-calibration, system calibration,
and background calibration options, and also allows the user to
read and write the on-chip calibration registers.
PRODUCT HIGHLIGHTS
1. The programmable gain front end allows the AD7710 to
accept input signals directly from a strain gage or transducer,
removing a considerable amount of signal conditioning.
3. The AD7710 allows the user to read and write the on-chip
calibration registers. This means that the microcontroller has
much greater control over the calibration procedure.
4. No missing codes ensures true, usable, 23-bit dynamic range
coupled with excellent ± 0.0015% accuracy. The effects of
temperature drift are eliminated by on-chip self-calibration,
which removes zero-scale and full-scale errors.
REV. G
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2004 Analog Devices, Inc. All rights reserved.
(AV = +5 V ⴞ 5%; DV = +5 V ⴞ 5%; V = 0 V or –5 V ⴞ 5%; REF IN(+) = +2.5 V;
AD7710–SPECIFICATIONS
REF IN(–) = AGND; MCLK IN = 10 MHz unless otherwise noted. All specifications T to T , unless otherwise noted.)
DD
DD
SS
MIN
Parameter
STATIC PERFORMANCE
No Missing Codes
Output Noise
Integral Nonlinearity @ +25°C
TMIN to TMAX
Positive Full-Scale Error2, 3
Full-Scale Drift5
Unipolar Offset Error2
Unipolar Offset Drift5
Bipolar Zero Error2
Bipolar Zero Drift5
Gain Drift
Bipolar Negative Full-Scale Error 2 @ 25°C
TMIN to TMAX
Bipolar Negative Full-Scale Drift 5
ANALOG INPUTS/REFERENCE INPUTS
Input Common-Mode Rejection (CMR)
Common-Mode Voltage Range 6
Normal-Mode 50 Hz Rejection 7
Normal-Mode 60 Hz Rejection 7
Common-Mode 50 Hz Rejection 7
Common-Mode 60 Hz Rejection 7
DC Input Leakage Current 7 @ 25°C
TMIN to TMAX
Sampling Capacitance7
Analog Inputs8
Input Voltage Range9
Input Sampling Rate, f S
Reference Inputs
REF IN(+) – REF IN(–) Voltage 11
Input Sampling Rate, f S
MAX
A, S Versions1 Unit
Conditions/Comments
24
22
18
15
12
Tables I and II
± 0.0015
± 0.003
See Note 4
1
0.3
See Note 4
0.5
0.25
See Note 4
0.5
0.25
2
± 0.003
± 0.006
1
0.3
µV/°C typ
µV/°C typ
Guaranteed by Design. For Filter Notches ≤ 60 Hz
For Filter Notch = 100 Hz
For Filter Notch = 250 Hz
For Filter Notch = 500 Hz
For Filter Notch = 1 kHz
Depends on Filter Cutoffs and Selected Gain
Filter Notches ≤ 60 Hz
Typically ± 0.0003%
Excluding Reference
Excluding Reference. For Gains of 1, 2
Excluding Reference. For Gains of 4, 8, 16, 32, 64, 128
µV/°C typ
µV/°C typ
For Gains of 1, 2
For Gains of 4, 8, 16, 32, 64, 128
µV/°C typ
µV/°C typ
ppm/°C typ
% of FSR max
% of FSR max
µV/°C typ
µV/°C typ
For Gains of 1, 2
For Gains of 4, 8, 16, 32, 64, 128
100
90
VSS to AVDD
100
100
150
150
10
1
20
dB min
dB min
V min to V max
dB min
dB min
dB min
dB min
pA max
nA max
pF max
0 to +VREF10
± VREF
See Table III
nom
nom
2.5 to 5
V min to V max For Specified Performance. Part Is Functional with
Lower VREF Voltages
Bits min
Bits min
Bits min
Bits min
Bits min
% of FSR max
% of FSR max
Excluding Reference
Typically ± 0.0006%
Excluding Reference. For Gains of 1, 2
Excluding Reference. For Gains of 4, 8, 16, 32, 64, 128
At DC and AVDD = 5 V
At DC and AVDD = 10 V
For Filter Notches of 10, 25, 50 Hz,
For Filter Notches of 10, 30, 60 Hz,
For Filter Notches of 10, 25, 50 Hz,
For Filter Notches of 10, 30, 60 Hz,
± 0.02 × fNOTCH
± 0.02 × fNOTCH
± 0.02 × fNOTCH
± 0.02 × fNOTCH
For Normal Operation. Depends on Gain Selected
Unipolar Input Range (B/U Bit of Control Register = 1)
Bipolar Input Range (B/U Bit of Control Register = 0)
fCLK IN/256
NOTES
1
Temperature ranges are as follows: A Version, –40°C to +85°C; S Version, –55°C to +125°C. See also Note 16.
2
Applies after calibration at the temperature of interest.
3
Positive full-scale error applies to both unipolar and bipolar input ranges.
4
These errors will be of the order of the output noise of the part as shown in Table I after system calibration. These errors will be 20 µV typical after self-calibration
or background calibration.
5
Recalibration at any temperature or use of the background calibration mode will remove these drift errors.
6
This common-mode voltage range is allowed, provided that the input voltage on AIN(+) and AIN(–) does not exceed AV DD + 30 mV and VSS – 30 mV.
7
These numbers are guaranteed by design and/or characterization.
8
The analog inputs present a very high impedance dynamic load that varies with clock frequency and input sample rate. The maximum recommended source
resistance depends on the selected gain (see Tables IV and V).
9
The analog input voltage range on the AIN1(+) and AIN2(+) inputs is given here with respect to the voltage on the AIN1(–) and AIN2(–) inputs. The absolute
voltage on the analog inputs should not go more positive than AV DD + 30 mV or go more negative than V SS – 30 mV.
10
VREF = REF IN(+) – REF IN(–).
11
The reference input voltage range may be restricted by the input voltage range requirement on the VBIAS input.
–2–
REV. G
AD7710
Parameter
REFERENCE OUTPUT
Output Voltage
Initial Tolerance @ 25°C
Drift
Output Noise
Line Regulation (AVDD)
Load Regulation
External Current
VBIAS INPUT12
Input Voltage Range
A, S Versions1
Unit
2.5
±1
20
30
1
1.5
1
V nom
% max
ppm/°C typ
µV typ
Peak-peak Noise 0.1 Hz to 10 Hz Bandwidth
mV/V max
mV/mA max Maximum Load Current 1 mA
mA max
AVDD – 0.85 × VREF
or AVDD – 3.5
V max
or AVDD – 2.1
VSS + 0.85 × VREF
or VSS + 3
V min
or VSS + 2.1
65 to 85
V min
dB typ
± 10
µΑ max
0.8
2.0
V max
V min
0.8
3.5
V max
V min
LOGIC OUTPUTS
VOL, Output Low Voltage
VOH, Output High Voltage
Floating State Leakage Current
Floating State Output Capacitance 13
0.4
DVDD – 1
± 10
9
V max
V min
µA max
pF typ
TRANSDUCER BURNOUT
Current
Initial Tolerance @ 25°C
Drift
4.5
± 10
0.1
µA nom
% typ
%/°C typ
COMPENSATION CURRENT
Output Current
Initial Tolerance @ 25°C
Drift
Line Regulation (AVDD)
Load Regulation
Output Compliance
20
±4
35
20
20
AVDD – 2
µA nom
µA max
ppm/°C typ
nA/V max
nA/V max
V max
(1.05 × VREF)/GAIN
–(1.05 × VREF)/GAIN
–(1.05 × VREF)/GAIN
0.8 × VREF/GAIN
(2.1 × VREF)/GAIN
V max
V max
V max
V min
V max
VBIAS Rejection
LOGIC INPUTS
Input Current
All Inputs Except MCLK IN
VINL, Input Low Voltage
VINH, Input High Voltage
MCLK IN Only
VINL, Input Low Voltage
VINH, Input High Voltage
SYSTEM CALIBRATION
Positive Full-Scale Calibration Limit l4
Negative Full-Scale Calibration Limit l4
Offset Calibration Limits 15
Input Span15
V max
Conditions/Comments
See VBIAS Input Section
Whichever Is Smaller: +5 V/–5 V or +10 V/0 V
Nominal AVDD/VSS
Whichever Is Smaller; +5 V/0 V Nominal AV DD/VSS
See VBIAS Input Section
Whichever Is Greater; +5 V/–5 V or +10 V/0 V
Nominal AVDD/VSS
Whichever Is Greater; +5 V/0 V Nominal AV DD/VSS
Increasing with Gain
ISINK = 1.6 mA
ISOURCE = 100 µA
AVDD = +5 V
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
GAIN Is the Selected PGA Gain (Between 1 and 128)
NOTES
12
The AD7710 is tested with the following V BIAS voltages. With AV DD = 5 V and VSS = 0 V, VBIAS = 2.5 V; with AV DD = 10 V and VSS = 0 V, VBIAS = 5 V; and with
AVDD = 5 V and VSS = –5 V, VBIAS = 0 V.
13
Guaranteed by design, not production tested.
14
After calibration, if the analog input exceeds positive full scale, the converter will output all 1s. If the analog input is less than negative full scale then the device will
output all 0s.
15
These calibration and span limits apply, provided the absolute voltage on the analog inputs does not exceed AVDD + 30 mV or go more negative than V SS – 30 mV.
The offset calibration limit applies to both the unipolar zero point and the bipolar zero point.
REV. G
–3–
AD7710–SPECIFICATIONS
Parameter
POWER REQUIREMENTS
Power Supply Voltages
AVDD Voltage16
DVDD Voltage17
AVDD-VSS Voltage
Power Supply Currents
AVDD Current
DVDD Current
VSS Current
Power Supply Rejection 18
Positive Supply (AVDD and DVDD)
Negative Supply (VSS)
Power Dissipation
Normal Mode
Standby (Power-Down) Mode
A, S Versionsl
Unit
Conditions/Comments
5 to 10
5
10.5
V nom
V nom
V max
± 5% for Specified Performance
± 5% for Specified Performance
For Specified Performance
4
4.5
1.5
mA max
mA max
mA max
See Note 19
90
dB typ
dB typ
45
52.5
15
mW max
mW max
mW max
VSS = –5 V
Rejection w.r.t. AGND; Assumes V BIAS Is Fixed
AVDD = DVDD = 5 V, VSS = 0 V; Typically 25 mW
AVDD = DVDD = 5 V, VSS = –5 V; Typically 30 mW
AVDD = DVDD = 5 V, VSS = 0 V or –5 V; Typically 7 mW
NOTES
16
The AD7710 is specified with a 10 MHz clock for AV DD voltages of +5 V ± 5%. It is specified with an 8 MHz clock for AV DD voltages greater than 5.25 V and less
than 10.5 V. Operating with AV DD voltages in the range 5.25 V to 10.5 V is only guaranteed over the 0°C to 70°C temperature range.
17
The ± 5% tolerance on the DV DD input is allowed provided that DV DD does not exceed AV DD by more than 0.3 V.
18
Measured at dc and applies in the selected passband. PSRR at 50 Hz will exceed 120 dB with filter notches of 10 Hz, 25 Hz, or 50 Hz. PSRR at 60 Hz will exceed
120 dB with filter notches of 10 Hz, 30 Hz or 60 Hz.
19
PSRR depends on gain: Gain of 1: 70 dB typ; Gain of 2: 75 dB typ; Gain of 4: 80 dB typ; Gains of 8 to 128: 85 dB typ. These numbers can be improved (to 95 dB
typ) by deriving the V BIAS voltage (via Zener diode or reference) from the AV DD supply.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS*
(TA = 25°C, unless otherwise noted.)
Digital Input Voltage to DGND . . . . . –0.3 V to AVDD + 0.3 V
Digital Output Voltage to DGND . . . . –0.3 V to DVDD + 0.3 V
Operating Temperature Range
Commercial (A Version) . . . . . . . . . . . . . . . –40°C to +85°C
Extended (S Version) . . . . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . . . 300°C
Power Dissipation (Any Package) to +75°C . . . . . . . . 450 mW
Derates Above +75°C . . . . . . . . . . . . . . . . . . . . . . . . 6 mW/°C
AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
AVDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
AVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +12 V
DVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
DVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
VSS to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –6 V
VSS to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –6 V
Analog Input Voltage to AGND
. . . . . . . . . . . . . . . . . . . . . . . . . VSS – 0.3 V to AVDD + 0.3 V
Reference Input Voltage to AGND
. . . . . . . . . . . . . . . . . . . . . . . . . VSS – 0.3 V to AVDD + 0.3 V
REF OUT to AGND . . . . . . . . . . . . . . . . . . . . –0.3 V to AVDD
*Stresses above those listed under Absolute Maximum Ratings may cause
permanent damage to the device. This is a stress rating only; functional operation
of the device at these or any other conditions above those listed in the operational
sections of the specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD7710 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. G
AD7710
3
1, 2 (DVDD = +5 V ⴞ 5%; AVDD = +5 V or +10 V ⴞ 5%; VSS = 0 V or –5 V ⴞ 10%; AGND = DGND =
TIMING CHARACTERISTICS
Parameter
0 V; fCLK IN =10 MHz; Input Logic 0 = 0 V, Logic 1 = DVDD, unless otherwise noted.)
Limit at TMIN, TMAX
(A, S Versions)
Unit
Conditions/Comments
400
10
8
0.4 × tCLK IN
0.4 × tCLK IN
50
50
1000
kHz min
MHz max
MHz max
ns min
ns min
ns max
ns max
ns min
Master Clock Frequency: Crystal Oscillator or Externally
Supplied for Specified Performance
AVDD = +5 V ± 5%
AVDD = +5.25 V to +10.5 V
Master Clock Input Low Time. tCLK IN = 1/fCLK IN
Master Clock Input High Time
Digital Output Rise Time. Typically 20 ns
Digital Output Fall Time. Typically 20 ns
SYNC Pulse Width
0
0
2 × tCLK IN
0
4 × tCLK IN + 20
4 × tCLK IN + 20
tCLK IN/2
tCLK IN/2 + 30
tCLK IN/2
3 × tCLK IN/2
50
0
4 × tCLK IN + 20
4 × tCLK IN
0
10
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns max
ns nom
ns nom
ns min
ns min
ns max
ns min
ns min
ns min
fCLK IN4, 5
tCLK IN LO
tCLK IN HI
tr6
tf 6
t1
Self-Clocking Mode
t2
t3
t4
t5
t6
t7 7
t8 7
t9
t10
t14
t15
t16
t17
t18
t19
DRDY to RFS Setup Time
DRDY to RFS Hold Time
A0 to RFS Setup Time
A0 to RFS Hold Time
RFS Low to SCLK Falling Edge
Data Access Time (RFS Low to Data Valid)
SCLK Falling Edge to Data Valid Delay
SCLK High Pulse Width
SCLK Low Pulse Width
A0 to TFS Setup Time
A0 to TFS Hold Time
TFS to SCLK Falling Edge Delay Time
TFS to SCLK Falling Edge Hold Time
Data Valid to SCLK Setup Time
Data Valid to SCLK Hold Time
NOTES
1
Guaranteed by design, not production tested. All input signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.
2
See Figures 10 to 13.
3
The AD7710 is specified with a 10 MHz clock for AV DD voltages of 5 V ± 5%. It is specified with an 8 MHz clock for AV DD voltages greater than 5.25 V and less
than 10.5 V.
4
CLK IN duty cycle range is 45% to 55%. CLK IN must be supplied whenever the AD7710 is not in STANDBY mode. If no clock is present in this case, the device
can draw higher current than specified and possibly become uncalibrated.
5
The AD7710 is production tested with f CLK IN at 10 MHz (8 MHz for AV DD > 5.25 V). It is guaranteed by characterization to operate at 400 kHz.
6
Specified using 10% and 90% points on waveform of interest.
7
These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross 0.8 V or 2.4 V.
ORDERING GUIDE
Model1
AD7710AN
AD7710AR
AD7710AR-REEL
AD7710AR-REEL7
AD7710ARZ3
AD7710ARZ-REEL3
AD7710ARZ-REEL73
AD7710AQ
AD7710SQ
EVAL-AD7710EB
Temperature
Range
Package
Options2
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–55°C to +125°C
N-24
R-24
R-24
R-24
R-24
R-24
R-24
Q-24
Q-24
Evaluation Board
NOTES
1
Contact your local sales office for military data sheet and availability.
2
N = PDIP; Q = CERDIP; R = SOIC.
3
Z = Pb-free part.
REV. G
–5–
AD7710
Parameter
External Clocking Mode
fSCLK
t20
t21
t22
t23
t247
t257
t26
t27
t28
t298
t30
t318
t32
t33
t34
t35
t36
Limit at TMIN, TMAX
(A, S Versions)
Unit
Conditions/Comments
fCLK IN/5
0
0
2 × tCLK IN
0
4 × tCLK IN
10
2 × tCLK IN + 20
2 × tCLK IN
2 × tCLK IN
tCLK IN + 10
10
tCLK IN + 10
10
5 × tCLK IN/2 + 50
0
0
4 × tCLK IN
2 × tCLK IN – SCLK High
30
MHz max
ns min
ns min
ns min
ns min
ns max
ns min
ns max
ns min
ns min
ns max
ns min
ns max
ns min
ns max
ns min
ns min
ns min
ns min
ns min
Serial Clock Input Frequency
DRDY to RFS Setup Time
DRDY to RFS Hold Time
A0 to RFS Setup Time
A0 to RFS Hold Time
Data Access Time (RFS Low to Data Valid)
SCLK Falling Edge to Data Valid Delay
SCLK High Pulse Width
SCLK Low Pulse Width
SCLK Falling Edge to DRDY High
SCLK to Data Valid Hold Time
RFS/TFS to SCLK Falling Edge Hold Time
RFS to Data Valid Hold Time
A0 to TFS Setup Time
A0 to TFS Hold Time
SCLK Falling Edge to TFS Hold Time
Data Valid to SCLK Setup Time
Data Valid to SCLK Hold Time
NOTES
8
These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then
extrapolated back to remove effects of charging or discharging the 100 pF capacitor. This means that the times quoted in the timing characteristics are the true bus
relinquish times of the part and, as such, are independent of external bus loading capacitances.
Specifications subject to change without notice.
PIN CONFIGURATION
DIP AND SOIC
1.6mA
TO OUTPUT
PIN
+2.1V
100pF
200␮A
Figure 1. Load Circuit for Access Time and
Bus Relinquish Time
SCLK
1
24 DGND
MCLK IN
2
23 DVDD
MCLK OUT
3
22 SDATA
A0
4
21 DRDY
SYNC
5
MODE
6
AIN1(+)
7
AIN1(–)
8
AIN2(+)
20 RFS
19 TFS
TOP VIEW
(Not to Scale) 18 AGND
17 IOUT
9
16 REF OUT
AIN2(–) 10
15 REF IN(+)
VSS 11
14 REF IN(–)
AVDD 12
–6–
AD7710
13 VBIAS
REV. G
AD7710
PIN FUNCTION DESCRIPTIONS
Pin Mnemonic
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Function
SCLK
Serial Clock. Logic input/output, depending on the status of the MODE pin. When MODE is high, the
device is in its self-clocking mode, and the SCLK pin provides a serial clock output. This SCLK becomes
active when RFS or TFS goes low, and it goes high impedance when either RFS or TFS returns high or when
the device has completed transmission of an output word. When MODE is low, the device is in its external
clocking mode, and the SCLK pin acts as an input. This input serial clock can be a continuous clock with all
data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous clock with the
information being transmitted to the AD7710 in smaller batches of data.
MCLK IN
Master Clock Signal for the Device. This can be provided in the form of a crystal or external clock. A crystal
can be tied across the MCLK IN and MCLK OUT pins. Alternatively, the MCLK IN pin can be driven with
a CMOS compatible clock and MCLK OUT left unconnected. The clock input frequency is nominally 10 MHz.
MCLK OUT When the master clock for the device is a crystal, the crystal is connected between MCLK IN and MCLK OUT.
A0
Address Input. With this input low, reading and writing to the device is to the control register. With this
input high, access is to either the data register or the calibration registers.
SYNC
Logic Input. Allows for synchronization of the digital filters when using a number of AD7710s. It resets
the nodes of the digital filter.
MODE
Logic Input. When this pin is high, the device is in its self-clocking mode; with this pin low, the device is in
its external clocking mode.
AIN1(+)
Analog Input Channel 1. Positive input of the programmable gain differential analog input. The AIN1(+)
input is connected to an output current source that can be used to check that an external transducer has
burned out or gone open circuit. This output current source can be turned on/off via the control register.
AIN1(–)
Analog Input Channel 1. Negative input of the programmable gain differential analog input.
AIN2(+)
Analog Input Channel 2. Positive input of the programmable gain differential analog input.
AIN2(–)
Analog Input Channel 2. Negative input of the programmable gain differential analog input.
Analog Negative Supply, 0 V to –5 V. Tied to AGND for single-supply operation. The input voltage on
VSS
AIN1 or AIN2 should not go > 30 mV negative w.r.t. VSS for correct operation of the device.
Analog Positive Supply Voltage, 5 V to 10 V.
AVDD
Input Bias Voltage. This input voltage should be set such that VBIAS + 0.85 × VREF < AVDD and VBIAS –
VBIAS
0.85 × VREF > VSS where VREF is REF IN(+) – REF IN(–). Ideally, this should be tied halfway between
AVDD and VSS. Thus with AVDD = 5 V and VSS = 0 V, it can be tied to REF OUT; with AVDD = 5 V
and VSS = –5 V, it can be tied to AGND; with AVDD = 10 V, it can be tied to 5 V.
REF IN(–)
Reference Input. The REF IN(–) can lie anywhere between AVDD and VSS provided REF IN(+) is greater
than REF IN(–).
REF IN(+)
Reference Input. The reference input is differential providing that REF IN(+) is greater than REF IN(–).
REF IN(+) can lie anywhere between AVDD and VSS.
REF OUT
Reference Output. The internal 2.5 V reference is provided at this pin. This is a single-ended output which
is referred to AGND. It is a buffered output which is capable of providing 1 mA to an external load.
Compensation Current Output. A 20 µA constant current is provided at this pin. This current can be used in
IOUT
association with an external thermistor to provide cold junction compensation in thermocouple applications.
This current can be turned on or off via the control register.
AGND
Ground Reference Point for Analog Circuitry.
REV. G
–7–
AD7710
Pin
Mnemonic
Function
19
TFS
20
RFS
21
DRDY
22
SDATA
23
24
DVDD
DGND
Transmit Frame Synchronization. Active low logic input used to write serial data to the device with serial data
expected after the falling edge of this pulse. In the self-clocking mode, the serial clock becomes active after
TFS goes low. In the external clocking mode, TFS must go low before the first bit of the data-word is written
to the part.
Receive Frame Synchronization. Active low logic input used to access serial data from the device. In the
self-clocking mode, the SCLK and SDATA lines both become active after RFS goes low. In the external
clocking mode, the SDATA line becomes active after RFS goes low.
Logic Output. A falling edge indicates that a new output word is available for transmission. The DRDY pin
will return high upon completion of transmission of a full output word. DRDY is also used to indicate when
the AD7710 has completed its on-chip calibration sequence.
Serial Data. Input/output with serial data being written to either the control register or the calibration registers, and serial data being accessed from the control register, calibration registers, or the data register.
During an output data read operation, serial data becomes active after RFS goes low (provided DRDY is low).
During a write operation, valid serial data is expected on the rising edges of SCLK when TFS is low. The
output data coding is natural binary for unipolar inputs and offset binary for bipolar inputs.
Digital Supply Voltage, 5 V. DVDD should not exceed AVDD by more than 0.3 V in normal operation.
Ground Reference Point for Digital Circuitry.
Terminology Integral Nonlinearity
Positive Full-Scale Overrange
This is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The
endpoints of the transfer function are zero scale (not to be confused with bipolar zero), a point 0.5 LSB below the first code
transition (000 . . . 000 to 000 . . . 001) and full scale, a point
0.5 LSB above the last code transition (111 . . . 110 to 111 . . .
111). The error is expressed as a percentage of full scale.
Positive full-scale overrange is the amount of overhead available
to handle input voltages on AIN(+) input greater than AIN(–) +
VREF/GAIN (for example, noise peaks or excess voltages due to
system gain errors in system calibration routines) without introducing errors due to overloading the analog modulator or to
overflowing the digital filter.
Positive Full-Scale Error
This is the amount of overhead available to handle voltages on
AIN(+) below AIN(–) –VREF/GAIN without overloading the
analog modulator or overflowing the digital filter. Note that the
analog input will accept negative voltage peaks even in the unipolar mode provided that AIN(+) is greater than AIN(–) and
greater than VSS – 30 mV.
Negative Full-Scale Overrange
Positive full-scale error is the deviation of the last code transition (111 . . . 110 to 111 . . . 111) from the ideal AIN(+) voltage
(AIN(–) + VREF/GAIN – 3/2 LSBs). It applies to both unipolar
and bipolar analog input ranges.
Unipolar Offset Error
Unipolar offset error is the deviation of the first code transition
from the ideal AIN(+) voltage (AIN(–) + 0.5 LSB) when operating in the unipolar mode.
Offset Calibration Range
In the system calibration modes, the AD7710 calibrates its offset
with respect to the analog input. The offset calibration range
specification defines the range of voltages that the AD7710 can
accept and still calibrate offset accurately.
Bipolar Zero Error
This is the deviation of the midscale transition (0111 . . . 111 to
1000 . . . 000) from the ideal AIN(+) voltage (AIN(–) – 0.5 LSB)
when operating in the bipolar mode.
Full-Scale Calibration Range
This is the range of voltages that the AD7710 can accept in the
system calibration mode and still calibrate full scale correctly.
Bipolar Negative Full-Scale Error
This is the deviation of the first code transition from the ideal
AIN(+) voltage (AIN(–) – VREF/GAIN + 0.5 LSB) when operating in the bipolar mode.
Input Span
In system calibration schemes, two voltages applied in sequence
to the AD7710’s analog input define the analog input range.
The input span specification defines the minimum and maximum input voltages from zero- to full-scale that the AD7710 can
accept and still calibrate gain accurately.
–8–
REV. G
AD7710
CONTROL REGISTER (24 BITS)
A write to the device with the A0 input low writes data to the control register. A read to the device with the A0 input low accesses the
contents of the control register. The control register is 24 bits wide; 24 bits of data must be written to the register or the data will not
be loaded. In other words, it is not possible to write just the first 12 bits of data into the control register. If more than 24 clock pulses
are provided before TFS returns high, then all clock pulses after the 24th clock pulse are ignored. Similarly, a read operation from the
control register should access 24 bits of data.
MSB
MD2
MD1
MD0
G2
G1
G0
CH
PD
WL
IO
BO
FS11
FS10
FS9
FS8
FS7
FS6
FS5
FS4
FS3
FS2
FS1
B/U
FS0
LSB
Operating Mode
MD2
MD1
MD0
Operating Mode
0
0
0
Normal Mode. This is the normal mode where a read to the device with A0 high accesses data from
the data register. This is the default condition of these bits after the internal power-on reset.
0
0
1
Activate Self-Calibration. This activates self-calibration on the channel selected by CH. This is a one-step
calibration sequence, and when complete, the part returns to normal mode (with MD2, MD1, MD0 of
the control register returning to 0, 0, 0). The DRDY output indicates when this self-calibration is complete.
For this calibration type, the zero-scale calibration is done internally on shorted (zeroed) inputs, and the
full-scale calibration is done internally on VREF.
0
1
0
Activate System Calibration. This activates system calibration on the channel selected by CH. This is a
two-step calibration sequence, with the zero-scale calibration done first on the selected input channel and
DRDY indicating when this zero-scale calibration is complete. The part returns to normal mode at the
end of this first step in the two-step sequence.
0
1
1
Activate System Calibration. This is the second step of the system calibration sequence with full-scale
calibration being performed on the selected input channel. Once again, DRDY indicates when the fullscale calibration is complete. When this calibration is complete, the part returns to normal mode.
1
0
0
Activate System Offset Calibration. This activates system offset calibration on the channel selected by
CH. This is a one-step calibration sequence and, when complete, the part returns to normal mode with
DRDY indicating when this system offset calibration is complete. For this calibration type, the zero-scale
calibration is done on the selected input channel, and the full-scale calibration is done internally on VREF.
1
0
1
Activate Background Calibration. This activates background calibration on the channel selected by CH. If
the background calibration mode is on, then the AD7710 provides continuous self-calibration of the
reference and shorted (zeroed) inputs. This calibration takes place as part of the conversion sequence,
extending the conversion time and reducing the word rate by a factor of 6. The major advantage of using
this mode is that the user does not have to recalibrate the device when there is a change in the ambient
temperature. In this mode, the shorted (zeroed) inputs and VREF, as well as the analog input voltage, are
continuously monitored and the calibration registers of the device are automatically updated.
1
1
0
Read/Write Zero-Scale Calibration Coefficients. A read to the device with A0 high accesses the contents
of the zero-scale calibration coefficients of the channel selected by CH. A write to the device with A0 high
writes data to the zero-scale calibration coefficients of the channel selected by CH. The word length for
reading and writing these coefficients is 24 bits, regardless of the status of the WL bit of the control
register. Therefore, 24 bits of data must be written to the calibration register, or the new data will not be
transferred to the calibration register.
1
1
1
Read/Write Full-Scale Calibration Coefficients. A read to the device with A0 high accesses the contents of
the full-scale calibration coefficients of the channel selected by CH. A write to the device with A0 high
writes data to the full-scale calibration coefficients of the channel selected by CH. The word length for
reading and writing these coefficients is 24 bits, regardless of the status of the WL bit of the control
register. Therefore, 24 bits of data must be written to the calibration register, or the new data will not be
transferred to the calibration register.
REV. G
–9–
AD7710
PGA GAIN
G2
G1
G0
Gain
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
4
8
16
32
64
128
(Default Condition after the Internal Power-On Reset)
CHANNEL SELECTION
CH
0
1
Channel
AIN1
AIN2
(Default Condition after the Internal Power-On Reset)
Power-Down
PD
0
1
Normal Operation
Power-Down
(Default Condition after the Internal Power-On Reset)
Word Length
WL
Output Word Length
0
1
16-Bit
24-Bit
(Default Condition after Internal Power-On Reset)
Output Compensation Current
IO
0
1
Off
On
(Default Condition after Internal Power-On Reset)
Burn-Out Current
BO
0
1
Off
On
(Default Condition after Internal Power-On Reset)
Bipolar/Unipolar Selection (Both Inputs)
B/U
0
1
Bipolar
Unipolar
(Default Condition after Internal Power-On Reset)
FILTER SELECTION (FS11–FS0)
The on-chip digital filter provides a sinc3 (or (sinx/x)3) filter
response. The 12 bits of data programmed into these bits determine the filter cutoff frequency, the position of the first notch of
the filter and the data rate for the part. In association with the
gain selection, it also determines the output noise (and therefore
the effective resolution) of the device.
The first notch of the filter occurs at a frequency determined by
the relationship: filter first notch frequency = (fCLK IN/512)/code
where code is the decimal equivalent of the code in bits FS0 to
FS11 and is in the range 19 to 2,000. With the nominal fCLK IN
of 10 MHz, this results in a first notch frequency range from
9.76 Hz to 1.028 kHz. To ensure correct operation of the
AD7710, the value of the code loaded to these bits must be
within this range. Failure to do this will result in unspecified
operation of the device.
Changing the filter notch frequency, as well as the selected gain,
impacts resolution. Tables I and II and Figure 2 show the effect
of the filter notch frequency and gain on the effective resolution
of the AD7710. The output data rate (or effective conversion
time) for the device is equal to the frequency selected for the
first notch of the filter. For example, if the first notch of the
filter is selected at 50 Hz, then a new word is available at a 50 Hz
rate or every 20 ms. If the first notch is at 1 kHz, a new word is
available every 1 ms.
The settling time of the filter to a full-scale step input change is
worst case 4 × 1/(output data rate). This settling time is to
100% of the final value. For example, with the first filter notch
at 50 Hz, the settling time of the filter to a full-scale step input
change is 80 ms max. If the first notch is at 1 kHz, the settling
time of the filter to a full-scale input step is 4 ms max. This
settling time can be reduced to 3 × l/(output data rate) by synchronizing the step input change to a reset of the digital filter. In
other words, if the step input takes place with SYNC low, the
settling time will be 3 × l/(output data rate). If a change of channels takes place, the settling time is 3 × l/(output data rate)
regardless of the SYNC input.
The –3 dB frequency is determined by the programmed first
notch frequency according to the relationship:
filter –3 dB frequency = 0.262 × first notch frequency.
–10–
REV. G
AD7710
Tables I and II show the output rms noise for some typical
notch and –3 dB frequencies. The numbers given are for the
bipolar input ranges with a VREF of 2.5 V. These numbers are
typical and are generated with an analog input voltage of 0 V.
The output noise from the part comes from two sources. First,
there is the electrical noise in the semiconductor devices used in
the implementation of the modulator (device noise). Second,
when the analog input signal is converted into the digital domain, quantization noise is added. The device noise is at a low
level and is largely independent of frequency. The quantization
noise starts at an even lower level but rises rapidly with increasing frequency to become the dominant noise source. Consequently, lower filter notch settings (below 60 Hz approximately)
tend to be device-noise dominated while higher notch settings
are dominated by quantization noise. Changing the filter notch
and cutoff frequency in the quantization noise dominated region
results in a more dramatic improvement in noise performance
than it does in the device noise dominated region as shown in
Table I. Furthermore, quantization noise is added after the PGA,
so effective resolution is independent of gain for the higher filter
notch frequencies. Meanwhile, device noise is added in the PGA
and, therefore, effective resolution suffers a little at high gains
for lower notch frequencies.
At the lower filter notch settings (below 60 Hz), the no missing
codes performance of the device is at the 24-bit level. At the
higher settings, more codes will be missed until at the 1 kHz
notch setting; no missing codes performance is guaranteed
only to the 12-bit level. However, because the effective resolution of the part is 10.5 bits for this filter notch setting, this
no missing codes performance should be more than adequate
for all applications.
The effective resolution of the device is defined as the ratio of
the output rms noise to the input full scale. This does not remain constant with increasing gain or with increasing bandwidth. Table II is the same as Table I except that the output is
expressed in terms of effective resolution (the magnitude of the
rms noise with respect to 2 × VREF/GAIN, the input full scale).
It is possible to do post filtering on the device to improve the
output data rate for a given –3 dB frequency and also to further
reduce the output noise (see the Digital Filtering section).
Table I. Output Noise vs. Gain and First Notch Frequency
First Notch of
Filter and O/P –3 dB
Data Rate1
Frequency
2
10 Hz
25 Hz2
30 Hz2
50 Hz2
60 Hz2
100 Hz3
250 Hz3
500 Hz3
1 kHz3
2.62 Hz
6.55 Hz
7.86 Hz
13.1 Hz
15.72 Hz
26.2 Hz
65.5 Hz
131 Hz
262 Hz
Typical Output RMS Noise (␮V)
Gain of 1 Gain of 2
Gain of 4
Gain of 8
Gain of 16
Gain of 32
Gain of 64
Gain of 128
1.0
1.8
2.5
4.33
5.28
13
130
0.6 × 103
3.1 × 103
0.48
0.63
0.84
1.2
1.33
3.7
25
140
0.7 × 103
0.33
0.5
0.57
0.64
0.87
1.8
12
70
0.29 × 103
0.25
0.44
0.46
0.54
0.63
1.1
7.5
35
180
0.25
0.41
0.43
0.46
0.62
0.9
4
25
120
0.25
0.38
0.4
0.46
0.6
0.65
2.7
15
70
0.25
0.38
0.4
0.46
0.56
0.65
1.7
8
40
0.78
1.1
1.31
2.06
2.36
6.4
75
0.26 × 103
1.6 × 103
NOTES
1
The default condition (after the internal power-on reset) for the first notch of filter is 60 Hz.
2
For these filter notch frequencies, the output rms noise is primarily dominated by device noise, and, as a result, is independent of the value of the reference voltage.
Therefore, increasing the reference voltage will give an increase in the effective resolution of the device (that is, the ratio of the rms noise to the input full scale is
increased because the output rms noise remains constant as the input full scale increases).
3
For these filter notch frequencies, the output rms noise is dominated by quantization noise, and, as a result, is proportional to the value of the reference voltage.
Table II. Effective Resolution vs. Gain and First Notch Frequency
Effective Resolution* (Bits)
First Notch of
Filter and O/P –3 dB
Data Rate
Frequency Gain of 1
Gain of 2 Gain of 4
Gain of 8
Gain of 16
Gain of 32
Gain of 64
Gain of 128
10 Hz
25 Hz
30 Hz
50 Hz
60 Hz
100 Hz
250 Hz
500 Hz
1 kHz
21.5
21
21
20
20
18.5
15
13
10.5
21
20
20
19.5
19.5
18.5
15.5
13
11
20.5
19.5
19.5
19
19
18
15.5
13
11
19.5
18.5
18.5
18.5
18
17.5
15.5
12.5
10.5
18.5
17.5
17.5
17.5
17
17
15
12.5
10
17.5
16.5
16.5
16.5
16
16
14.5
12.5
10
2.62 Hz
6.55 Hz
7.86 Hz
13.1 Hz
15.72 Hz
26.2 Hz
65.5 Hz
131 Hz
262 Hz
22.5
21.5
21
20
20
18.5
15
13
10.5
21.5
21
20.5
20
20
18.5
15.5
13
11
NOTE
*Effective resolution is defined as the magnitude of the output rms noise with respect to the input full scale (i.e., 2 × VREF/GAIN). The above table applies for a V REF
of 2.5 V and resolution numbers are rounded to the nearest 0.5 LSB.
REV. G
–11–
AD7710
Figure 2 show information similar to that outlined in Table I. In this plot, however, the output rms noise is shown for the full range
of available cutoffs frequencies. The numbers given in these plots are typical values at 25°C.
1k
10k
GAIN OF 1
GAIN OF 2
GAIN OF 16
GAIN OF 4
100
GAIN OF 8
OUTPUT NOISE – ␮V
OUTPUT NOISE – ␮V
1k
100
10
GAIN OF 64
GAIN OF 128
10
1
1
0.1
10
GAIN OF 32
0.1
10
NOTCH FREQUENCY – Hz
100
1k
NOTCH FREQUENCY – Hz
Figure 2a. Output Noise vs. Gain and Notch
Frequency (Gains of 1 to 8)
Figure 2b. Output Noise vs. Gain and Notch
Frequency (Gains of 16 to 128)
100
1k
10k
CIRCUIT DESCRIPTION
The AD7710 is a sigma-delta A/D converter with on-chip digital
filtering for measuring wide dynamic range, low frequency signals in applications such as weigh scale, industrial control, or
process control. It contains a sigma-delta (or charge-balancing)
ADC, a calibration microcontroller with on-chip static RAM, a
clock oscillator, a digital filter, and a bidirectional serial communications port.
10k
The basic connection diagram for the part is shown in Figure 3.
This figure shows the AD7710 in the external clocking mode
with both the AVDD and DVDD pins being driven from the analog 5 V supply. Some applications have separate supplies for
both AVDD and DVDD, and in some cases, the analog supply
exceeds the 5 V digital supply (see the Power Supplies and
Grounding section).
The part contains two programmable gain differential analog
input channels. The gain range is from 1 to 128 allowing the
part to accept unipolar signals of 0 mV to 20 mV and 0 V to
2.5 V, or bipolar signals in the range of ± 20 mV to ± 2.5 V when
the reference input voltage equals 2.5 V. The input signal to the
selected analog input channel is continuously sampled at a rate
determined by the frequency of the master clock, MCLK IN,
and the selected gain (see Table III). A charge-balancing A/D
converter (sigma-delta modulator) converts the sampled signal
into a digital pulse train whose duty cycle contains the digital
information. The programmable gain function on the analog
input is also incorporated in this sigma-delta modulator with the
input sampling frequency being modified to give the higher
gains. A sinc3 digital low-pass filter processes the output of the
sigma-delta modulator and updates the output register at a rate
determined by the first notch frequency of the filter. The output
data can be read from the serial port randomly or periodically at
any rate up to the output register update rate. The first notch of
this digital filter (and therefore its –3 dB frequency) can be
programmed via an on-chip control register. The programmable
range for this first notch frequency is 9.76 Hz to 1.028 kHz,
giving a programmable range for the –3 dB frequency of 2.58 Hz
to 269 Hz.
–12–
ANALOG
+5V SUPPLY
10␮F
0.1␮F
0.1␮F
AVDD
DVDD
DRDY
DIFFERENTIAL
ANALOG INPUT
DIFFERENTIAL
ANALOG INPUT
AIN1(+)
AIN1(–)
AIN2(+)
AIN2(–)
AD7710
IOUT
ANALOG
GROUND
AGND
DIGITAL
GROUND
DGND
VSS
REF OUT
REF IN(+)
DATA
READY
TFS
TRANSMIT
(WRITE)
RFS
RECEIVE
(READ)
SDATA
SERIAL
DATA
SCLK
SERIAL
CLOCK
A0
ADDRESS
INPUT
MODE
SYNC
+5V
MCLK OUT
VBIAS
REF IN(–)
MCLK IN
Figure 3. Basic Connection Diagram
REV. G
AD7710
The AD7710 provides a number of calibration options that can
be programmed via the on-chip control register. A calibration
cycle may be initiated at any time by writing to this control
register. The part can perform self-calibration using the on-chip
calibration microcontroller and SRAM to store calibration
parameters. Other system components may also be included in
the calibration loop to remove offset and gain errors in the input
channel, using the system calibration mode. Another option is a
background calibration mode where the part continuously performs self-calibration and updates the calibration coefficients.
Once the part is in this mode, the user does not have to issue
periodic calibration commands to the device or to recalibrate
when there is a change in the ambient temperature or power
supply voltage.
The AD7710 gives the user access to the on-chip calibration
registers, allowing the microprocessor to read the device calibration coefficients and also to write its own calibration coefficients
to the part from prestored values in E2PROM. This gives the
microprocessor much greater control over the AD7710’s calibration procedure. It also means that the user can verify that the
calibration is correct by comparing the coefficients after calibration with prestored values in E2PROM.
The AD7710 samples the input signal at a frequency of 39 kHz or
greater (see Table III). As a result, the quantization noise is
spread over a much wider frequency than that of the band of
interest. The noise in the band of interest is reduced still further
by analog filtering in the modulator loop, which shapes the
quantization noise spectrum to move most of the noise energy to
frequencies outside the bandwidth of interest. The noise performance is thus improved from this 1-bit level to the performance
outlined in Tables I and II and in Figures 2a and 2b.
The output of the comparator provides the digital input for the
1-bit DAC, so that the system functions as a negative feedback
loop that tries to minimize the difference signal. The digital data
that represents the analog input voltage is contained in the duty
cycle of the pulse train appearing at the output of the comparator. It can be retrieved as a parallel binary data-word using a
digital filter.
Sigma-delta ADCs are generally described by the order of the
analog low-pass filter. A simple example of a first-order sigmadelta ADC is shown in Figure 5. This contains only a first-order
low-pass filter or integrator. It also illustrates the derivation of
the alternative name for these devices, charge-balancing ADCs.
DIFFERENTIAL
AMPLIFIER
The AD7710 can be operated in single-supply systems if the analog
input voltage does not go more negative than –30 mV. For larger
bipolar signals, a VSS of –5 V is required by the part. For battery
operation, the AD7710 also offers a programmable standby
mode that reduces idle power consumption to typically 7 mW.
INTEGRATOR
COMPARATOR
VIN
+FS
THEORY OF OPERATION
DAC
The general block diagram of a sigma-delta ADC is shown in
Figure 4. It contains the following elements:
–FS
• A sample-hold amplifier.
Figure 5. Basic Charge-Balancing ADC
• A differential amplifier or subtracter.
• An analog low-pass filter.
• A 1-bit A/D converter (comparator).
• A 1-bit DAC.
• A digital low-pass filter.
COMPARATOR
S/H AMP
ANALOG
LOW-PASS
FILTER
DIGITAL
FILTER
DAC
DIGITAL DATA
Figure 4. General Sigma-Delta ADC
In operation, the analog signal sample is fed to the subtracter,
along with the output of the 1-bit DAC. The filtered difference
signal is fed to the comparator, which samples the difference
signal at a frequency many times that of the analog signal sampling frequency (oversampling).
The device consists of a differential amplifier (whose output is
the difference between the analog input and the output of a
1-bit DAC), an integrator and a comparator. The term charge
balancing comes from the fact that this system is a negative
feedback loop that tries to keep the net charge on the integrator
capacitor at zero, by balancing charge injected by the input
voltage with charge injected by the 1-bit DAC. When the analog
input is zero, the only contribution to the integrator output
comes from the 1-bit DAC. For the net charge on the integrator
capacitor to be zero, the DAC output must spend half its time at
+FS and half its time at –FS. Assuming ideal components, the
duty cycle of the comparator will be 50%.
When a positive analog input is applied, the output of the 1-bit
DAC must spend a larger proportion of the time at +FS, so the
duty cycle of the comparator increases. When a negative input
voltage is applied, the duty cycle decreases.
The AD7710 uses a second-order sigma-delta modulator and a
digital filter that provides a rolling average of the sampled output. After power-up, or if there is a step change in the input
voltage, there is a settling time that must elapse before valid
data is obtained.
Oversampling is fundamental to the operation of sigma-delta
ADCs. Using the quantization noise formula for an ADC,
SNR = (6.02 × number of bits + 1.76) dB,
a 1-bit ADC or comparator yields an SNR of 7.78 dB.
REV. G
–13–
AD7710
0
Input Sample Rate
The modulator sample frequency for the device remains at
fCLK IN/512 (19.5 kHz @ fCLK IN = 10 MHz) regardless of the
selected gain. However, gains greater than ×1 are achieved by a
combination of multiple input samples per modulator cycle and
scaling the ratio of reference capacitor to input capacitor. As a
result of the multiple sampling, the input sample rate of the device
varies with the selected gain (see Table III). The effective input
impedance is 1/C × fS where C is the input sampling capacitance
and fS is the input sample rate.
–20
–40
–60
GAIN – dB
–80
–100
–120
–140
–160
–180
–200
Table III. Input Sampling Frequency vs. Gain
–220
–240
Gain
Input Sampling Frequency (fS)
1
2
4
8
16
32
64
128
fCLK IN/256 (39 kHz @ fCLK IN = 10 MHz)
2 × fCLK IN/256 (78 kHz @ fCLK IN = 10 MHz)
4 × fCLK IN/256 (156 kHz @ fCLK IN = 10 MHz)
8 × fCLK IN/256 (312 kHz @ fCLK IN = 10 MHz)
8 × fCLK IN/256 (312 kHz @ fCLK IN = 10 MHz)
8 × fCLK IN/256 (312 kHz @ fCLK IN = 10 MHz)
8 × fCLK IN/256 (312 kHz @ fCLK IN = 10 MHz)
8 × fCLK IN/256 (312 kHz @ fCLK IN = 10 MHz)
DIGITAL FILTERING
The AD7710 digital filter behaves like a similar analog filter,
with a few minor differences.
First, because digital filtering occurs after the A-to-D conversion
process, it can remove noise injected during the conversion
process. Analog filtering cannot do this.
On the other hand, analog filtering can remove noise superimposed on the analog signal before it reaches the ADC. Digital
filtering cannot do this, and noise peaks riding on signals near
full scale have the potential to saturate the analog modulator
and digital filter, even though the average value of the signal is
within limits. To alleviate this problem, the AD7710 has overrange headroom built into the sigma-delta modulator and digital
filter, which allows overrange excursions of 5% above the analog
input range. If noise signals are larger than this, consideration
should be given to analog input filtering, or to reducing the
input channel voltage so that its full scale is half that of the
analog input channel full scale. This will provide an overrange
capability greater than 100% at the expense of reducing the
dynamic range by 1 bit (50%).
Filter Characteristics
The cutoff frequency of the digital filter is determined by the
value loaded to bits FS0 to FS11 in the control register. At the
maximum clock frequency of 10 MHz, the minimum cutoff
frequency of the filter is 2.58 Hz while the maximum programmable cutoff frequency is 269 Hz.
Figure 6 shows the filter frequency response for a cutoff frequency of 2.62 Hz, which corresponds to a first filter notch
frequency of 10 Hz. This is a (sinx/x)3 response (also called
sinc3) that provides >100 dB of 50 Hz and 60 Hz rejection.
Programming a different cutoff frequency via FS0–FS11 does
not alter the profile of the filter response, but changes the frequency of the notches as outlined in the Control Register section.
0
10
20
30
40
50
FREQUENCY – Hz
60
70
Figure 6. Frequency Response of AD7710 Filter
Since the AD7710 contains this on-chip, low-pass filtering,
there is a settling time associated with step function inputs, and
data from the output will be invalid after a step change until the
settling time has elapsed. The settling time depends upon the
notch frequency chosen for the filter. The output data rate
equates to this filter notch frequency and the settling time of the
filter to a full-scale step input that is four times the output data
period. In applications using both input channels, the settling
time of the filter must be allowed to elapse before data from the
second channel is accessed.
Post Filtering
The on-chip modulator provides samples at a 19.5 kHz output
rate. The on-chip digital filter decimates these samples to provide data at an output rate that corresponds to the programmed
first notch frequency of the filter. Because the output data rate
exceeds the Nyquist criterion, the output rate for a given bandwidth will satisfy most application requirements. However,
there may be some applications that require a higher data rate
for a given bandwidth and noise performance. Applications that
need a higher data rate will require some post filtering following
the digital filter of the AD7710.
For example, if the required bandwidth is 7.86 Hz but the
required update rate is 100 Hz, the data can be taken from the
AD7710 at the 100 Hz rate, giving a –3 dB bandwidth of 26.2 Hz.
Post filtering can be applied to this to reduce the bandwidth and
output noise to the 7.86 Hz bandwidth level, while maintaining
an output rate of 100 Hz.
Post filtering can also to reduce the output noise from the device
for bandwidths below 2.62 Hz. At a gain of 128, the output rms
noise is 250 nV. This is essentially device noise or white noise, and
because the input is chopped, the noise has a flat frequency
response. By reducing the bandwidth below 2.62 Hz, the noise in
the resultant pass band can be reduced. A reduction in bandwidth
by a factor of 2 results in a √2 reduction in the output rms noise.
This additional filtering will result in a longer settling time.
–14–
REV. G
AD7710
Antialias Considerations
The digital filter does not provide any rejection at integer multiples of the modulator sample frequency (n × 19.5 kHz, where
n = 1, 2, 3 . . . ). This means that there are frequency bands
± f3 dB wide (f3 dB is cutoff frequency selected by FS0 to FS11),
where noise passes unattenuated to the output. However, due to
the AD7710’s high oversampling ratio, these bands occupy only
a small fraction of the spectrum, and most broadband noise is
filtered. In any case, because of the high oversampling ratio a
simple RC, single-pole filter is generally sufficient to attenuate
the signals in these bands on the analog input and thus provide
adequate antialiasing filtering.
If passive components are placed in front of the AD7710, ensure
that the source impedance is low enough to keep from introducing gain errors in the system. The dc input impedance for
the AD7710 is over 1 GΩ. The input appears as a dynamic
load that varies with the clock frequency and with the selected
gain (see Figure 7). The input sample rate, as shown in Table III,
determines the time allowed for the analog input capacitor CIN
to be charged. External impedances result in a longer charge
time for this capacitor, which may result in gain errors being
introduced on the analog inputs. Table IV shows the allowable
external resistance/capacitance values that do not introduce gain
error to the 16-bit level, while Table V shows the allowable
external resistance/capacitance values that do not introduce gain
error to the 20-bit level. Both inputs of the differential input
channels look into similar input circuitry.
AD7710
RINT
7k⍀ TYP
HIGH
IMPEDANCE
>1G⍀
AIN
CINT
ANALOG INPUT FUNCTIONS
Analog Input Ranges
Both analog inputs are differential, programmable gain input
channels that can handle either unipolar or bipolar input signals.
The common-mode range of these inputs is from VSS to AVDD,
provided that the absolute value of the analog input voltage lies
between VSS –30 mV and AVDD +30 mV.
The dc input leakage current is 10 pA maximum at 25°C
(± 1 nA over temperature). This results in a dc offset voltage
developed across the source impedance. However, this dc offset
effect can be compensated for by a combination of the differential input capability of the part and its system calibration mode.
Burnout Current
The AIN1(+) input of the AD7710 contains a 4.5 µA current
source that can be turned on/off via the control register. This
current source can be used in checking that a transducer has not
burned out or gone open circuit before attempting to take measurements on that channel. If the current is turned on and
allowed to flow into the transducer and a measurement of the
input voltage on the AIN1 input is taken, it can indicate that the
transducer has burned out or gone open circuit. For normal
operation, this burnout current is turned off by writing a 0 to
the BO bit in the control register.
Output Compensation Current
The AD7710 also contains a feature that allows the user to
implement cold junction compensation in thermocouple applications. This can be achieved using the output compensation
current from the IOUT pin of the device. Once again, this current
can be turned on/off via the control register. Writing a 1 to the
IO bit of the control register enables this compensation current.
11.5pF TYP
VBIAS
SWITCHING FREQUENCY DEPENDS ON
fCLKIN AND SELECTED GAIN
Figure 7. Analog Input Impedance
Table IV. External Series Resistance That Do Not Introduce
16-Bit Gain Error
External Capacitance (pF)
Gain
0
50
100
500
1000
5000
1
2
4
8–128
184 kΩ
88.6 kΩ
41.4 kΩ
17.6 kΩ
45.3 kΩ
22.1 kΩ
10.6 kΩ
4.8 kΩ
27.1 kΩ
13.2 kΩ
6.3 kΩ
2.9 kΩ
7.3 kΩ
3.6 kΩ
1.7 kΩ
790 Ω
4.1 kΩ
2.0 kΩ
970 Ω
440 Ω
1.1 kΩ
560 Ω
270 Ω
120 Ω
Table V. External Series Resistance That Do Not Introduce
20-Bit Gain Error
External Capacitance (pF)
Gain
0
50
100
500
1000
5000
1
2
4
8–128
145 kΩ
70.5 kΩ
31.8 kΩ
13.4 kΩ
34.5 kΩ
16.9 kΩ
8.0 kΩ
3.6 kΩ
20.4 kΩ
10 kΩ
4.8 kΩ
2.2 kΩ
5.2 kΩ
2.5 kΩ
1.2 kΩ
550 Ω
2.8 kΩ
1.4 kΩ
670 Ω
300 Ω
700 Ω
350 Ω
170 Ω
80 Ω
REV. G
The numbers in Tables IV and V assume a full-scale change on
the analog input. In any case, an error introduced due to longer
charging times is a gain error that can be removed using the
system calibration capabilities of the AD7710, provided that the
resultant span is within the span limits of the system calibration
techniques.
The compensation current provides a 20 µA constant current
source that can be used in association with a thermistor or a
diode to provide cold junction compensation. A common
method of generating cold junction compensation is to use a
temperature dependent current flowing through a fixed resistor
to provide a voltage that is equal to the voltage developed across
the cold junction at any temperature in the expected ambient
range. In this case, the temperature coefficient of the compensation current is so low compared with the temperature coefficient
of the thermistor that it can be considered constant with temperature. The temperature variation is then provided by the
variation of the thermistor’s resistance with temperature.
Normally, the cold junction compensation will be implemented
by applying the compensation voltage to the second input channel of the AD7710. Periodic conversion of this channel gives the
user a voltage that corresponds to the cold junction compensation voltage. This can be used to implement cold junction compensation in software with the result from the thermocouple
input being adjusted according to the result in the compensation
channel. Alternatively, the voltage can be subtracted from the
input voltage in an analog fashion, thereby using only one channel of the AD7710.
–15–
AD7710
Bipolar/Unipolar Inputs
The two analog inputs on the AD7710 can accept either unipolar or bipolar input voltage ranges. Bipolar or unipolar options
are chosen by programming the B/U bit of the control register.
This programs both channels for either type of operation.
Programming the part for either unipolar or bipolar operation
does not change any of the input signal conditioning; it simply changes the data output coding, using binary for unipolar
inputs and offset binary for bipolar inputs.
The input channels are differential and, as a result, the voltage
to which the unipolar and bipolar signals are referenced is the
voltage on the AIN(–) input. For example, if AIN(–) is 1.25 V
and the AD7710 is configured for unipolar operation with a
gain of 1 and a VREF of 2.5 V, the input voltage range on the
AIN(+) input is 1.25 V to 3.75 V. If AIN(–) is 1.25 V and
the AD7710 is configured for bipolar mode with a gain of 1
and a VREF of 2.5 V, the analog input range on the AIN(+)
input is –1.25 V to +3.75 V.
outlined in Tables I and II assumes a clean reference. If the
reference noise in the bandwidth of interest is excessive, it can
degrade the performance of the AD7710. Using the on-chip
reference as the reference source for the part (that is, connecting
REF OUT to REF IN) results in degraded output noise performance from the AD7710 for portions of the noise table that are
dominated by the device noise. The on-chip reference noise
effect is eliminated in ratiometric applications where the reference is used to provide the excitation voltage for the analog
front end. The connection scheme, shown in Figure 8, is recommended when using the on-chip reference. Recommended reference voltage sources for the AD7710 include the AD580 and
AD680 2.5 V references.
REF OUT
AD7710
REF IN (+)
REF IN (–)
REFERENCE INPUT/OUTPUT
The AD7710 contains a temperature compensated 2.5 V reference which has an initial tolerance of ± 1%. This reference voltage is provided at the REF OUT pin, and it can be used as the
reference voltage for the part by connecting the REF OUT pin
to the REF IN(+) pin. This REF OUT pin is a single-ended
output, referenced to AGND, which is capable of providing up
to 1 mA to an external load. In applications where REF OUT is
connected to REF IN(+), REF IN(–) should be tied to AGND
to provide the nominal 2.5 V reference for the AD7710.
The reference inputs of the AD7710, REF IN(+) and REF IN(–)
provide a differential reference input capability. The commonmode range for these differential inputs is from VSS to AVDD.
The nominal differential voltage, VREF (REF IN(+) – REF IN(–)),
is 2.5 V for specified operation, but the reference voltage can go
to 5 V with no degradation in performance if the absolute value
of REF IN(+) and REF IN(–) does not exceed its AVDD and
VSS limits, and the VBIAS input voltage range limits are obeyed.
The part is also functional with VREF voltage down to 1 V but
with degraded performance because the output noise will, in
terms of LSB size, be larger. REF IN(+) must always be greater
than REF IN(–) for correct operation of the AD7710.
Both reference inputs provide a high impedance, dynamic load
similar to the analog inputs. The maximum dc input leakage current is 10 pA (±1 nA over temperature), and source resistance may
result in gain errors on the part. The reference inputs look like the
analog input (see Figure 7). In this case, RINT is 5 kΩ typ and CINT
varies with gain. The input sample rate is fCLK IN/256 and does not
vary with gain. For gains of 1 to 8, CINT is 20 pF; for a gain of 16,
it is 10 pF; for a gain of 32, it is 5 pF; for a gain of 64, it is 2.5 pF;
and for a gain of 128, it is 1.25 pF.
The digital filter of the AD7710 removes noise from the reference
input just as it does with the analog input, and the same limitations apply regarding lack of noise rejection at integer multiples
of the sampling frequency. The output noise performance
Figure 8. REF OUT/REF IN Connection
VBIAS Input
The VBIAS input determines at what voltage the internal analog
circuitry is biased. It essentially provides the return path for
analog currents flowing in the modulator and, as such, it should
be driven from a low impedance point to minimize errors.
For maximum internal headroom, the VBIAS voltage should be
set halfway between AVDD and VSS. The difference between
AVDD and (VBIAS + 0.85 × VREF) determines the amount of
headroom the circuit has at the upper end, while the difference
between VSS and (VBIAS – 0.85 × VREF) determines the amount
of headroom the circuit has at the lower end. When choosing a
VBIAS voltage, ensure that it stays within prescribed limits. For
single 5 V operation, the selected VBIAS voltage must ensure that
VBIAS ± 0.85 × VREF does not exceed AVDD or VSS or that the
VBIAS voltage itself is greater than VSS + 2.1 V and less than
AVDD – 2.1 V. For single 10 V operation or dual ± 5 V operation, the selected VBIAS voltage must ensure that VBIAS ± 0.85 ×
VREF does not exceed AVDD or VSS, or that the VBIAS voltage
itself is greater than VSS + 3 V or less than AVDD –3 V. For
example, with AVDD = 4.75 V, VSS = 0 V, and VREF = 2.5 V, the
allowable range for the VBIAS voltage is 2.125 V to 2.625 V.
With AVDD = 9.5 V, VSS = 0 V, and VREF = 5 V, the range for
VBIAS is 4.25 V to 5.25 V. With AVDD = +4.75 V, VSS = –4.75 V,
and VREF = +2.5 V, the VBIAS range is –2.625 V to +2.625 V.
The VBIAS voltage does have an effect on the AVDD power supply
rejection performance of the AD7710. If the VBIAS voltage tracks
the AVDD supply, it improves the power supply rejection from
the AVDD supply line from 80 dB to 95 dB. Using an external
Zener diode, connected between the AVDD line and VBIAS, as the
source for the VBIAS voltage gives the improvement in AVDD
power supply rejection performance.
–16–
REV. G
AD7710
USING THE AD7710
SYSTEM DESIGN CONSIDERATIONS
Accuracy
The AD7710 operates differently from successive approximation ADCs or integrating ADCs. Because it samples the signal
continuously, like a tracking ADC, there is no need for a start
convert command. The output register is updated at a rate
determined by the first notch of the filter, and the output can be
read at any time, either synchronously or asynchronously.
Clocking
The AD7710 requires a master clock input, which may be an
external TTL/CMOS compatible clock signal applied to the
MCLK IN pin with the MCLK OUT pin left unconnected.
Alternatively, a crystal of the correct frequency can be connected
between MCLK IN and MCLK OUT, in which case the clock
circuit will function as a crystal-controlled oscillator. For lower
clock frequencies, a ceramic resonator may be used instead of
the crystal. For these lower frequency oscillators, external
capacitors may be required on either the ceramic resonator or
on the crystal.
The input sampling frequency, the modulator sampling frequency, the –3 dB frequency, the output update rate, and the
calibration time are all directly related to the master clock frequency fCLK IN. Reducing the master clock frequency by a factor
of 2 will halve the above frequencies and update rate and will
double the calibration time.
The current drawn from the DVDD power supply is also directly
related to fCLK IN. Reducing fCLK IN by a factor of 2 will halve the
DVDD current but will not affect the current drawn from the
AVDD power supply.
System Synchronization
If multiple AD7710s are operated from a common master clock,
they can be synchronized to update their output registers simultaneously. A falling edge on the SYNC input resets the filter and
places the AD7710 into a consistent, known state. A common
signal to the AD7710s’ SYNC inputs will synchronize their
operation. This would typically be done after each AD7710 has
performed its own calibration or has had calibration coefficients
loaded to it.
The SYNC input can also be used to reset the digital filter in
systems where the turn-on time of the digital power supply
(DVDD) is very long. In such cases, the AD7710 will start operating internally before the DVDD line has reached its minimum
operating level, 4.75 V. With a low DVDD voltage, the
AD7710’s internal digital filter logic does not operate correctly.
Thus, the AD7710 may have clocked itself into an incorrect
operating condition by the time that DVDD has reached its correct level. The digital filter will be reset upon issue of a calibration command (whether it is self-calibration, system calibration,
or background calibration) to the AD7710. This ensures correct
operation of the AD7710. In systems where the power-on
default conditions of the AD7710 are acceptable, and no calibration is performed after power-on, issuing a SYNC pulse to
the AD7710 will reset the AD7710’s digital filter logic. An R, C
on the SYNC line, with R, C time constant longer than the
DVDD power-on time, will perform the SYNC function.
REV. G
Sigma-delta ADCs, like VFCs and other integrating ADCs, do
not contain any source of nonmonotonicity and inherently offer
no missing codes performance. The AD7710 achieves excellent
linearity by the use of high quality, on-chip silicon dioxide
capacitors, which have a very low capacitance/voltage coefficient.
The device also achieves low input drift through the use of chopper
stabilized techniques in its input stage. To ensure excellent performance over time and temperature, the AD7710 uses digital
calibration techniques that minimize offset and gain error.
Autocalibration
Autocalibration on the AD7710 removes offset and gain errors
from the device. A calibration routine should be initiated on the
device whenever there is a change in the ambient operating
temperature or supply voltage. It should also be initiated if there
is a change in the selected gain, filter notch, or bipolar/unipolar
input range. However, if the AD7710 is in its background calibration mode, these changes are all automatically taken care of
(after the settling time of the filter has been allowed for).
The AD7710 offers self-calibration, system calibration, and
background calibration facilities. For calibration to occur on the
selected channel, the on-chip microcontroller must record the
modulator output for two different input conditions. These are
zero-scale and full-scale points. With these readings, the microcontroller can calculate the gain slope for the input to output
transfer function of the converter. Internally, the part works
with a resolution of 33 bits to determine its conversion result of
either 16 bits or 24 bits.
The AD7710 also provides the facility to write to the on-chip
calibration registers, and, in this manner, the span and offset for
the part can be adjusted by the user. The offset calibration register contains a value that is subtracted from all conversion
results, while the full-scale calibration register contains a value
that is multiplied by all conversion results. The offset calibration
coefficient is subtracted from the result prior to the multiplication by the full-scale coefficient. In the first three modes outlined here, the DRDY line indicates that calibration is complete
by going low. If DRDY is low before (or goes low during) the
calibration command, it may take up to one modulator cycle
before DRDY goes high to indicate that calibration is in
progress. Therefore, DRDY should be ignored for up to one
modulator cycle after the last bit of the calibration command is
written to the control register.
Self-Calibration
In the self-calibration mode with a unipolar input range, the
zero-scale point used in determining the calibration coefficients
is with both inputs shorted (that is, AIN(+) = AIN(–) = VBIAS)
and the full-scale point is VREF. The zero-scale coefficient is
determined by converting an internal shorted inputs node. The
full-scale coefficient is determined from the span between this
shorted inputs conversion and a conversion on an internal VREF
node. The self-calibration mode is invoked by writing the appropriate values (0, 0, 1) to the MD2, MD1, and MD0 bits of the
control register. In this calibration mode, the shorted inputs
node is switched in to the modulator first and a conversion is
–17–
AD7710
performed; the VREF node is then switched in and another conversion is performed. When the calibration sequence is complete, the
calibration coefficients updated, and the filter resettled to the analog input voltage, the DRDY output goes low. The self-calibration
procedure takes into account the selected gain on the PGA.
System calibration can also be used to remove any errors from
an antialiasing filter on the analog input. A simple R, C antialiasing filter on the front end may introduce a gain error on the
analog input voltage but the system calibration can be used to
remove this error.
For bipolar input ranges in the self-calibrating mode, the
sequence is very similar to that just outlined. In this case, the
two points that the AD7710 calibrates are midscale (bipolar
zero) and positive full scale.
System Offset Calibration
System Calibration
System calibration allows the AD7710 to compensate for
system gain and offset errors as well as its own internal errors.
System calibration performs the same slope factor calculations
as self-calibration but uses voltage values presented by the system to the AIN inputs for the zero- and full-scale points. System
calibration is a two-step process. The zero-scale point must be
presented to the converter first. It must be applied to the converter before the calibration step is initiated and remain stable
until the step is complete. System calibration is initiated by
writing the appropriate values (0, 1, 0) to the MD2, MD1,
MD0 bits of the control register. The DRDY output from the
device will signal when the step is complete by going low. After
the zero-scale point is calibrated, the full-scale point is applied,
and the second step of the calibration process is initiated by
again writing the appropriate values (0, 1, 1) to MD2, MD1,
MD0. Again the full-scale voltage must be set up before the
calibration is initiated, and it must remain stable throughout the
calibration step. DRDY goes low at the end of this second step
to indicate that the system calibration is complete. In the unipolar mode, the system calibration is performed between the
two endpoints of the transfer function; in the bipolar mode, it is
performed between midscale and positive full scale.
This two-step system calibration mode offers another feature.
After the sequence has been completed, additional offset or gain
calibrations can be performed by themselves to adjust the zero
reference point or the system gain. This is achieved by performing the first step of the system calibration sequence (by writing
0, 1, 0 to MD2, MD1, MD0). This will adjust the zero-scale or
offset point but will not change the slope factor from that set
during a full system calibration sequence.
System offset calibration is a variation of both the system calibration and self-calibration. In this case, the zero-scale point
for the system is presented to the AIN input of the converter.
System offset calibration is initiated by writing 1, 0, 0 to MD2,
MD1, MD0. The system zero-scale coefficient is determined by
converting the voltage applied to the AIN input, while the fullscale coefficient is determined from the span between this AIN
conversion and a conversion on VREF. The zero-scale point
should be applied to the AIN input for the duration of the calibration sequence. This is a one-step calibration sequence with
DRDY going low when the sequence is completed. In unipolar
mode, the system offset calibration is performed between the
two endpoints of the transfer function; in bipolar mode, it is
performed between midscale and positive full scale.
Background Calibration
The AD7710 also offers a background calibration mode where
the part interleaves its calibration procedure with its normal
conversion sequence. In background calibration mode, the same
voltages are used as the calibration points that are used in the
self-calibration mode, that is, shorted inputs and VREF. The
background calibration mode is invoked by writing 1, 0, 1 to
MD2, MD1, MD0 of the control register. When invoked, the
background calibration mode reduces the output data rate of the
AD7710 by a factor of 6 while the –3 dB bandwidth remains
unchanged. The advantage is that the part is continually performing calibration and automatically updating its calibration
coefficients. As a result, the effects of temperature drift, supply sensitivity, and time drift on zero- and full-scale errors are
automatically removed. When the background calibration mode
is turned on, the part will remain in this mode until bits MD2,
MD1, and MD0 of the control register are changed. With background calibration mode on, the first result from the AD7710
will be incorrect because the full-scale calibration will not have
been performed. For a step change on the input, the second
output update will have settled to 100% of the final value.
Table VI summarizes the calibration modes and the calibration
points associated with them. It also gives the duration from
when the calibration is invoked to when valid data is available to
the user.
Table VI. Calibration Truth Table
Cal Type
MD2, MD1, MD0
Zero-Scale Cal
Full-Scale Cal
Sequence
Duration
Self-Cal
System Cal
System Cal
System Offset Cal
Background Cal
0, 0, 1
0, 1, 0
0, 1, 1
1, 0, 0
1, 0, 1
Shorted Inputs
AIN
VREF
One Step
Two Steps
Two Steps
One Step
One Step
9 × 1/Output Rate
4 × 1/Output Rate
4 × 1/Output Rate
9 × 1/Output Rate
6 × 1/Output Rate
AIN
Shorted Inputs
–18–
AIN
VREF
VREF
REV. G
AD7710
The analog and digital supplies to the AD7710 are independent
and separately pinned out to minimize coupling between the
analog and digital sections of the device. The digital filter will
provide rejection of broadband noise on the power supplies,
except at integer multiples of the modulator sampling frequency.
The digital supply (DVDD) must not exceed the analog positive
supply (AVDD) by more than 0.3 V in normal operation. If separate analog and digital supplies are used, the recommended
decoupling scheme is shown in Figure 9. In systems where
AVDD = 5 V and DVDD = 5 V, it is recommended that AVDD
and DVDD are driven from the same 5 V supply, although
each supply should be decoupled separately as shown in Figure 9. It is preferable that the common supply is the system’s
analog 5 V supply.
Span and Offset Limits
Whenever a system calibration mode is used, there are limits on
the amount of offset and span that can be accommodated. The
range of input span in both the unipolar and bipolar modes has
a minimum value of 0.8 × VREF/GAIN and a maximum value of
2.1 × VREF/GAIN.
The amount of offset that can be accommodated depends on
whether the unipolar or bipolar mode is being used. This offset
range is limited by the requirement that the positive full-scale
calibration limit is ≤ 1.05 × VREF/GAIN. Therefore, the offset
range plus the span range cannot exceed 1.05 × VREF/GAIN. If
the span is at its minimum (0.8 × VREF/GAIN), the maximum
the offset can be is (0.25 × VREF/GAIN).
In bipolar mode, the system offset calibration range is again
restricted by the span range. The span range of the converter in
bipolar mode is equidistant around the voltage used for the
zero-scale point, thus the offset range plus half the span range
cannot exceed (1.05 × VREF/GAIN). If the span is set to 2 × VREF/
GAIN, the offset span cannot move more than ± (0.05 × VREF/
GAIN) before the endpoints of the transfer function exceed the
input overrange limits ± (1.05 × VREF/GAIN). If the span range
is set to the minimum ± (0.4 × VREF/GAIN), the maximum
allowable offset range is ± (0.65 × VREF/GAIN).
It is also important that power is applied to the AD7710 before
signals at REF IN, AIN, or the logic input pins in order to avoid
excessive current. If separate supplies are used for the AD7710
and the system digital circuitry, then the AD7710 should be
powered up first. If it is not possible to guarantee this, then
current limiting resistors should be placed in series with the
logic inputs.
DIGITAL +5V
SUPPLY
ANALOG
SUPPLY
10␮F
POWER-UP AND CALIBRATION
0.1␮F
On power-up, the AD7710 performs an internal reset, which
sets the contents of the control register to a known state. However, to ensure correct calibration for the device, a calibration
routine should be performed after power-up.
AVDD
DVDD
AD7710
The power dissipation and temperature drift of the AD7710
are low and no warm-up time is required before the initial
calibration is performed. However, if an external reference is
being used, this reference must have stabilized before calibration
is initiated.
Figure 9. Recommended Decoupling Scheme
DIGITAL INTERFACE
The AD7710’s serial communications port provides a flexible
arrangement to allow easy interfacing to industry-standard
microprocessors, microcontrollers, and digital signal processors.
A serial read to the AD7710 can access data from the output
register, the control register, or from the calibration registers. A
serial write to the AD7710 can write data to the control register
or the calibration registers.
Drift Considerations
The AD7710 uses chopper stabilization techniques to minimize
input offset drift. Charge injection in the analog switches and dc
leakage currents at the sampling node are the primary sources of
offset voltage drift in the converter. The dc input leakage current is
essentially independent of the selected gain. Gain drift within the
converter depends primarily upon the temperature tracking of the
internal capacitors. It is not affected by leakage currents.
Measurement errors due to offset drift or gain drift can be eliminated at any time by recalibrating the converter or by operating
the part in the background calibration mode. Using the system
calibration mode can also minimize offset and gain errors in the
signal conditioning circuitry. Integral and differential linearity
errors are not significantly affected by temperature changes.
POWER SUPPLIES AND GROUNDING
Because the analog inputs and reference input are differential,
most of the voltages in the analog modulator are common-mode
voltages. VBIAS provides the return path for most of the analog
currents flowing in the analog modulator. As a result, the VBIAS
input should be driven from a low impedance to minimize errors
due to charging/discharging impedances on this line. When the
internal reference is used as the reference source for the part,
AGND is the ground return for this reference voltage.
REV. G
0.1␮F
Two different modes of operation are available, optimized for
different types of interfaces where the AD7710 can act either as
master in the system (it provides the serial clock) or as slave (an
external serial clock can be provided to the AD7710). These
two modes, labeled self-clocking mode and external clocking
mode, are discussed in detail in the following sections.
Self-Clocking Mode
The AD7710 is configured for its self-clocking mode by tying
the MODE pin high. In this mode, the AD7710 provides the
serial clock signal used for the transfer of data to and from the
AD7710. This self-clocking mode can be used with processors
that allow an external device to clock their serial port including
most digital signal processors and microcontrollers such as the
68HC11 and 68HC05. It also allows easy interfacing to serialparallel conversion circuits in systems with parallel data communication, allowing interfacing to 74XX299 universal shift
registers without any additional decoding. In the case of shift
registers, the serial clock line should have a pull-down resistor
instead of the pull-up resistor shown in Figure 10 and Figure 11.
–19–
AD7710
Read Operation
Data can be read from either the output register, the control
register, or the calibration registers. A0 determines whether the
data read accesses data from the control register or from the
output/calibration registers. This A0 signal must remain valid
for the duration of the serial read operation. With A0 high, data is
accessed from either the output register or from the calibration
registers. With A0 low, data is accessed from the control register.
The function of the DRDY line is dependent only on the output
update rate of the device and the reading of the output data
register. DRDY goes low when a new data-word is available in
the output data register. It is reset high when the last bit of data
(either 16th bit or 24th bit) is read from the output register. If
data is not read from the output register, the DRDY line will
remain low. The output register will continue to be updated at
the output update rate, but DRDY will not indicate this. A read
from the device in this circumstance will access the most recent
word in the output register. If a new data-word becomes available to the output register while data is being read from the
output register, DRDY will not indicate this and the new dataword will be lost to the user. DRDY is not affected by reading
from the control register or the calibration registers.
Data can be accessed from the output data register only when
DRDY is low. If RFS goes low with DRDY high, no data transfer will take place. DRDY does not have any effect on reading
data from the control register or from the calibration registers.
Figure 10 shows a timing diagram for reading from the AD7710
in the self-clocking mode. This read operation shows a read
from the AD7710’s output data register. A read from the control
register or calibration registers is similar, but, in these cases, the
DRDY line is not related to the read function. Depending on
the output update rate, it can go low at any stage in the control/
calibration register read cycle without affecting the read and its
status should be ignored. A read operation from either the control or calibration registers must always read 24 bits of data
from the respective register.
Figure 10 shows a read operation from the AD7710. For the
timing diagram shown, it is assumed that there is a pull-up
resistor on the SCLK output. With DRDY low, the RFS input
is brought low. RFS going low enables the serial clock of the
AD7710 and also places the MSB of the word on the serial data
line. All subsequent data bits are clocked out on a high to low
transition of the serial clock and are valid prior to the following
rising edge of this clock. The final active falling edge of SCLK
clocks out the LSB and this LSB is valid prior to the final active
rising edge of SCLK. Coincident with the next falling edge of
SCLK, DRDY is reset high. DRDY going high turns off the
SCLK and the SDATA outputs. This means that the data hold
time for the LSB is slightly shorter than for all other bits.
DRDY (O)
t3
t2
A0 (I)
t5
t4
RFS (I)
t6
t9
SCLK (O)
t7
t8
t 10
THREE-STATE
SDATA (O)
MSB
LSB
Figure 10. Self-Clocking Mode, Output Data Read Operation
–20–
REV. G
AD7710
Write Operation
Read Operation
Data can be written to either the control register or calibration
registers. In either case, the write operation is not affected by
the DRDY line and does not have any effect on the status of
DRDY. A write operation to the control registers or calibration
register must always write 24 bits.
As with self-clocking mode, data can be read from either the
output register, the control register, or the calibration registers.
A0 determines whether the data read accesses data from the
control register or from the output/calibration registers. This A0
signal must remain valid for the duration of the serial read
operation. With A0 high, data is accessed from either the output
register or from the calibration registers. With A0 low, data is
accessed from the control register.
Figure 11 shows a write operation to the AD7710. A0 determines
whether a write operation transfers data to the control register or to
the calibration registers. This A0 signal must remain valid for the
duration of the serial write operation. The falling edge of TFS
enables the internally generated SCLK output. The serial data
to be loaded to the AD7710 must be valid on the rising edge of
this SCLK signal. Data is clocked into the AD7710 on the rising
edge of the SCLK signal with the MSB transferred first. On the
last active high time of SCLK, the LSB is loaded to the AD7710.
Subsequent to the next falling edge of SCLK, the SCLK output is
turned off. (The timing diagram in Figure 11 assumes a pull-up
resistor on the SCLK line.)
External Clocking Mode
The AD7710 is configured for external clocking mode by
tying the MODE pin low. In this mode, SCLK of the AD7710
is configured as an input, and an external serial clock must be
provided to this SCLK pin. This external clocking mode is
designed for direct interface to systems that provide a serial
clock output that is synchronized to the serial data output,
including microcontrollers such as the 80C51, 87C51, 68HC11,
68HC05, and most digital signal processors.
The function of the DRDY line is dependent only on the output
update rate of the device and the reading of the output data
register. DRDY goes low when a new data-word is available in
the output data register. It is reset high when the last bit of data
(either 16th bit or 24th bit) is read from the output register. If
data is not read from the output register, the DRDY line will
remain low. The output register will continue to be updated at
the output update rate, but DRDY will not indicate this. A read
from the device in this circumstance will access the most recent
word in the output register. If a new data-word becomes available to the output register while data is being read from the
output register, DRDY will not indicate this and the new dataword will be lost to the user. DRDY is not affected by reading
from the control register or the calibration register.
Data can be accessed from the output data register only when
DRDY is low. If RFS goes low while DRDY is high, no data
transfer will take place. DRDY does not have any effect on reading
data from the control register or from the calibration registers.
A0 (I)
t15
t14
TFS (I)
t17
t16
t9
SCLK (O)
t18
t10
t19
SDATA (I)
MSB
LSB
Figure 11. Self-Clocking Mode, Control/Calibration Register Write Operation
REV. G
–21–
AD7710
resets the DRDY line high. This rising edge of DRDY turns off
the serial data output.
Figures 12a and 12b show timing diagrams for reading from the
AD7710 in external clocking mode. In Figure 12a, all the data is
read from the AD7710 in one read operation. In Figure 12b, the
data is read from the AD7710 over a number of read operations.
Both read operations show a read from the AD7710’s output
data register. A read from the control register or calibration
registers is similar, but, in these cases, the DRDY line is not
related to the read function. Depending on the output update
rate, it can go low at any stage in the control/calibration register
read cycle without affecting the read, and its status should be
ignored. A read operation from either the control or calibration
registers must always read 24 bits of data.
Figure 12b shows a timing diagram for a read operation where
RFS returns high during the transmission of the word and
returns low again to access the rest of the data-word. Timing
parameters and functions are very similar to that outlined for
Figure 12a, but Figure 12b has a number of additional times to
show timing relationships when RFS returns high in the middle
of transferring a word.
RFS should return high during a low time of SCLK. On the
rising edge of RFS, the SDATA output is turned off. DRDY
remains low and will remain low until all bits of the data-word
are read from the AD7710, regardless of the number of times
RFS changes state during the read operation. Depending on the
time between the falling edge of SCLK and the rising edge of
RFS, the next bit (BIT N+1) may appear on the data bus before
RFS goes high. When RFS returns low again, it activates the
SDATA output. When the entire word is transmitted, the
DRDY line will go high, turning off the SDATA output as
shown in Figure 12a.
Figure 12a shows a read operation from the AD7710 where
RFS remains low for the duration of the data-word transmission. With DRDY low, the RFS input is brought low. The input
SCLK signal should be low between read and write operations.
RFS going low places the MSB of the word to be read on the
serial data line. All subsequent data bits are clocked out on a
high to low transition of the serial clock and are valid prior to
the following rising edge of this clock. The penultimate falling
edge of SCLK clocks out the LSB and the final falling edge
DRDY (O)
t 21
t 20
A0 (I)
t 23
t 22
RFS (I)
t 26
t 28
SCLK (I)
SDATA (O)
t 27
t 25
t 24
t 29
MSB
LSB
THREE-STATE
Figure 12a. External Clocking Mode, Output Data Read Operation
DRDY (O)
t20
A0 (I)
t 22
RFS (I)
t 26
t 30
SCLK (I)
t 27
t 24
t 31
t25
SDATA (O)
t 24
t25
THREE-STATE
MSB
BIT N
BIT N+1
Figure 12b. External Clocking Mode, Output Data Read Operation (RFS Returns High during Read Operation)
–22–
REV. G
AD7710
with the MSB transferred first. On the last active high time of
SCLK, the LSB is loaded to the AD7710.
Write Operation
Data can be written to either the control register or calibration
registers. In either case, the write operation is not affected by
the DRDY line and does not have any effect on the status of
DRDY. A write operation to the control register or the calibration register must always write 24 bits.
Figure 13b shows a timing diagram for a write operation to the
AD7710 with TFS returning high during the operation and
returning low again to write the rest of the data-word. Timing
parameters and functions are very similar to those outlined for
Figure 13a, but Figure 13b has a number of additional times to
show timing relationships when TFS returns high in the middle
of transferring a word.
Figure 13a shows a write operation to the AD7710 with TFS
remaining low for the duration of the operation. A0 determines
whether a write operation transfers data to the control register
or to the calibration registers. This A0 signal must remain valid
for the duration of the serial write operation. As before, the
serial clock line should be low between read and write operations. The serial data to be loaded to the AD7710 must be valid
on the high level of the externally applied SCLK signal. Data is
clocked into the AD7710 on the high level of this SCLK signal
Data to be loaded to the AD7710 must be valid prior to the
rising edge of the SCLK signal. TFS should return high during
the low time of SCLK. After TFS returns low again, the next bit
of the data-word to be loaded to the AD7710 is clocked in on
next high level of the SCLK input. On the last active high time
of the SCLK input, the LSB is loaded to the AD7710.
A0 (I)
t 33
t 32
TFS (I)
t 26
t 34
SCLK (I)
t36
t35
SDATA (I)
t 27
MSB
LSB
Figure 13a. External Clocking Mode, Control/Calibration Register Write Operation
A0 (I)
t 32
TFS (I)
t 26
t 30
SCLK (I)
t35
SDATA (I)
MSB
t 27
t35
t36
t36
BIT N
BIT N+1
Figure 13b. External Clocking Mode, Control/Calibration Register Write Operation
(TFS Returns High during Write Operation)
REV. G
–23–
AD7710
SIMPLIFYING THE EXTERNAL CLOCKING MODE
INTERFACE
START
In many applications, the user may not need to write to the on-chip
calibration registers. In this case, the serial interface to the AD7710
in external clocking mode can be simplified by connecting the TFS
line to the A0 input of the AD7710 (see Figure 14). This means
that any write to the device will load data to the control register
(because A0 is low while TFS is low), and any read to the device will access data from the output data register or from the
calibration registers (because A0 is high while RFS is low). Note
that in this arrangement the user does not have the capability of
reading from the control register.
CONFIGURE AND
INITIALIZE ␮C/␮P
SERIAL PORT
BRING
RFS, TFS HIGH
POLL DRDY
RFS
FOUR
INTERFACE
LINES
SDATA
SCLK
AD7710
DRDY
LOW?
TFS
A0
NO
YES
BRING
RFS LOW
Figure 14. Simplified Interface with TFS Connected to A0
Another method of simplifying the interface is to generate the
TFS signal from an inverted RFS signal. However, generating
the signals the opposite way around (RFS from an inverted
TFS) will cause writing errors.
ⴛ3
READ
SERIAL BUFFER
MICROCOMPUTER/MICROPROCESSOR INTERFACING
The AD7710’s flexible serial interface allows for easy interface
to most microcomputers and microprocessors. Figure 15 shows
a flowchart for a typical programming sequence for reading data
from the AD7710 to a microcomputer, while Figure 16 shows a
flowchart for writing data to the AD7710. Figures 17, 18, and
19 show some typical interface circuits.
Figure 15 shows continuous read operations from the AD7710
output register, where the DRDY line is continuously polled.
Depending on the microprocessor configuration, the DRDY line
may come to an interrupt input, in which case the DRDY will
automatically generate an interrupt without being polled. Reading the serial buffer could be anything from one read operation
up to three read operations (where 24 bits of data are read into
an 8-bit serial register). A read operation to the control/calibration registers is similar, but, in this case, the status of DRDY
can be ignored. The A0 line is brought low when the RFS line
is brought low during a read register.
The flowchart also shows the bits being reversed after they have
been read in from the serial port. This depends on whether the
microprocessor expects the MSB of the word first or the LSB of
the word first. The AD7710 outputs the MSB first.
BRING
RFS HIGH
REVERSE
ORDER OF BITS
Figure 15. Flowchart for Continuous Read Operations
to the AD7710
Figure 16 also shows the option of the bits being reversed before
being written to the serial buffer. This depends on whether the
first bit transmitted by the microprocessor is the MSB or the
LSB. The AD7710 expects the MSB as the first bit in the data
stream. In cases where the data is being read or being written in
bytes and the data has to be reversed, the bits have to be reversed
for every byte.
Figure 16 shows a single 24-bit write operation to the AD7710
control or calibration registers. This shows data being transferred from data memory to the accumulator before being written to the serial buffer. Some microprocessor systems allow data
to be written directly to the serial buffer from data memory.
Writing data to the serial buffer from the accumulator generally
consists of either two or three write operations, depending on
the size of the serial buffer.
–24–
REV. G
AD7710
Table VII shows some typical 8XC51 code used for a single 24-bit
read from the output register of the AD7710. Table VIII shows
some typical code for a single write operation to the control register
of the AD7710. The 8XC51 outputs the LSB first in a write
operation, while the AD7710 expects the MSB first so the data to
be transmitted has to be rearranged before being written to the
output serial register. Similarly, the AD7710 outputs the MSB first
during a read operation, while the 8XC51 expects the LSB first.
Therefore, the data that is read into the serial buffer needs to be
rearranged before the correct data-word from the AD7710 is
available in the accumulator.
START
CONFIGURE AND
INITIALIZE ␮C/␮P
SERIAL PORT
BRING
RFS, TFS, AND A0
HIGH
LOAD DATA FROM
ADDRESS TO
ACCUMULATOR
Table VII. 8XC51 Code for Reading from the AD7710
MOV SCON,#00010001B; Configure 8051 for MODE 0
REVERSE
ORDER OF
BITS
MOV IE,#00010000B;
SETB 90H;
SETB 91H;
SETB 93H;
MOV R1,#003H;
BRING
TFS AND A0 LOW
MOV R0,#030H;
ⴛ3
WRITE DATA FROM
ACCUMULATOR TO
SERIAL BUFFER
BRING
TFS AND A0 HIGH
END
Figure 16. Flowchart for Single Write Operation
to the AD7710
AD7710 to 8XC51 Interface
Figure 17 shows an interface between the AD7710 and the 8XC51
microcontroller. The AD7710 is configured for external clocking mode, while the 8XC51 is configured in its Mode 0 serial
interface mode. The DRDY line from the AD7710 is connected
to the Port P1.2 input of the 8XC51, so the DRDY line is polled
by the 8XC51. The DRDY line can be connected to the INT1
input of the 8XC51 if an interrupt driven system is preferred.
DVDD
SYNC
P1.0
8XC51
RFS
P1.1
TFS
P1.2
DRDY
P1.3
A0
P3.0
SDATA
P3.1
AD7710
SCLK
MOV R6,#004H;
WAIT:
NOP;
MOV A,P1;
Read Port 1
ANL A,R6;
Mask Out All Bits Except DRDY
JZ READ;
If Zero Read
SJMP WAIT;
Otherwise Keep Polling
READ:
CLR 90H;
Bring RFS Low
CLR 98H;
Clear Receive Flag
POLL:
JB 98H, READ1
Tests Receive Interrupt Flag
SJMP POLL
READ 1:
MOV A,SBUF;
Read Buffer
RLC A;
Rearrange Data
MOV B.0,C;
Reverse Order of Bits
RLC A; MOV B.1,C; RLC A; MOV B.2,C;
RLC A; MOV B.3,C; RLC A; MOV B.4,C;
RLC A; MOV B.5,C; RLC A; MOV B.6,C;
RLC A; MOV B.7,C;
MOV A,B;
MOV @R0,A;
Write Data to Memory
INC R0;
Increment Memory Location
DEC R1
Decrement Byte Counter
MOV A,R1
JZ END
Jump if Zero
JMP WAIT
Fetch Next Byte
END:
SETB 90H
Bring RFS High
FIN:
SJMP FIN
MODE
Figure 17. AD7710 to 8XC51 Interface
REV. G
Disable All Interrupts
Set P1.0, Used as RFS
Set P1.1, Used as TFS
Set P1.3, Used as A0
Sets Number of Bytes to Be Read in
a Read Operation
Start Address for Where Bytes Will
Be Loaded
Use P1.2 as DRDY
–25–
AD7710
Table VIII. 8XC51 Code for Writing to the AD7710
MOV SCON,#00000000B;
MOV IE,#10010000B;
MOV IP,#00010000B;
SETB 91H;
SETB 90H;
MOV R1,#003H;
MOV R0,#030H;
MOV A,#00H;
MOV SBUF,A;
WAIT:
JMP WAIT;
INT ROUTINE:
NOP;
MOV A,R1;
JZ FIN;
DEC R1;
MOV A,@R;
INC R0;
RLC A;
AD7710 to 68HC11 Interface
Configure 8051 for MODE 0
Operation and Enable Serial Reception
Enable Transmit Interrupt
Prioritize the Transmit Interrupt
Bring TFS High
Bring TFS High
Sets Number of Bytes to Be Written
in a Write Operation
Start Address in RAM for Bytes
Clear Accumulator
Initialize the Serial Port
Wait for Interrupt
Interrupt Subroutine
Load R1 to Accumulator
If Zero Jump to FIN
Decrement R1 Byte Counter
Move Byte into the Accumulator
Increment Address
Rearrange Data from LSB First
to MSB First
MOV B.0,C; RLC A; MOV B.1,C; RLC A;
MOV B.2,C; RLC A; MOV B.3,C; RLC A;
MOV B.4,C; RLC A; MOV B.5,C; RLC A;
MOV B.6,C; RLC A: MOV B.7,C; MOV A,B;
CLR 93H;
Bring A0 Low
CLR 91H;
Bring TFS Low
MOV SBUF,A;
Write to Serial Port
RETI;
Return from Subroutine
FIN:
SETB 91H;
Set TFS High
SETB 93H;
Set A0 High
RETI;
Return from Interrupt Subroutine
Figure 18 shows an interface between the AD7710 and the
68HC11 microcontroller. The AD7710 is configured for its
external clocking mode, while the SPI port is used on the 68HC11
in single-chip mode. The DRDY line from the AD7710 is connected to the Port PC2 input of the 68HC11, so the DRDY line
is polled by the 68HC11. The DRDY line can be connected to
the IRQ input of the 68HC11 if an interrupt driven system is
preferred. The 68HC11 MOSI and MISO lines should be
configured for wire-OR operation. Depending on the interface
configuration, it may be necessary to provide bidirectional buffers between the 68HC11 MOSI and MISO lines.
The 68HC11 is configured in master mode with its CPOL bit
set to a Logic 0 and its CPHA bit set to a logic 1. With a 10-MHz
master clock on the AD7710, the interface operates with all four
serial clock rates of the 68HC11.
DVDD
SS
PC0
68HC11
DVDD
SYNC
RFS
PC1
TFS
PC2
DRDY
PC3
A0
SCK
SCLK
MISO
SDATA
MOSI
MODE
AD7710
Figure 18. AD7710 to 68HC11 Interface
–26–
REV. G
AD7710
reference voltage for the AD7710 generated across a resistor
that is placed in series with the bridge network. In this case, the
value of the reference resistor is determined by the required
reference voltage divided by the value of the excitation current.
APPLICATIONS
Figure 19 shows a strain gage interfaced directly to one of the
analog input channels of the AD7710. The differential inputs to
the AD7710 are connected directly to the bridge network of the
strain gage. In the diagram shown, the on-chip reference of the
AD7710 provides the voltage for the bridge network and also
provides the reference voltage for the AD7710. An alternative
scheme, outlined in Figure 20, shows the analog positive supply
voltage powering the bridge network and the AD7710, with the
The on-chip PGA allows the AD7710 to handle an analog input
voltage range as low as 20 mV full scale. The differential inputs
of the part allow this analog input range to have an absolute
value anywhere between VSS and AVDD.
ANALOG
5V SUPPLY
REF
OUT
ACTIVE
GAGE
REF
IN(–)
REF
IN(+)
AVDD
DVDD
2.5V
REFERENCE
R
CHARGE-BALANCING A/D
CONVERTER
AIN1(+)
DUMMY
GAGE
VBIAS
AUTO-ZEROED
Σ-∆
MODULATOR
PGA
R
AIN1(–)
M
U
X
AIN2(+)
SYNC
DIGITAL
FILTER
A = 1 – 128
MCLK
IN
CLOCK
GENERATION
AIN2(–)
MCLK
OUT
SERIAL INTERFACE
CONTROL
REGISTER
OUTPUT
REGISTER
AD7710
AGND
DGND
RFS TFS MODE SDATA SCLK DRDY A0
VSS
Figure 19. Strain-Gage Application with the AD7710
DIGITAL
5V SUPPLY
ANALOG SUPPLY
EXCITATION
CURRENT
R=
VREF
AVDD
DVDD
REF
OUT
VBIAS
REF IN(+)
IEXCITATION
ACTIVE
GAGE
2.5V
REFERENCE
REF IN(–)
CHARGE-BALANCING A/D
CONVERTER
R
AIN1(+)
DUMMY
GAGE
R
AIN1(–)
AUTO-ZEROED
Σ-∆
MODULATOR
PGA
M
U
X
DIGITAL
FILTER
SYNC
A = 1 – 128
AIN2(+)
CLOCK
GENERATION
AIN2(–)
MCLK
IN
MCLK
OUT
SERIAL INTERFACE
CONTROL
REGISTER
AD7710
AGND
DGND
VSS
OUTPUT
REGISTER
RFS TFS MODE SDATA SCLK DRDY A0
Figure 20. Alternate Scheme for Generating AD7710 Reference Voltage
REV. G
–27–
AD7710
OUTLINE DIMENSIONS
24-Lead Plastic Dual In-Line Package [PDIP]
(N-24)
Dimensions shown in inches and (millimeters)
1.185 (30.01)
1.165 (29.59)
1.145 (29.08)
0.295 (7.49)
0.285 (7.24)
0.275 (6.99)
24
13
1
12
0.180
(4.57)
MAX
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.015 (0.38) MIN
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.100
(2.54)
BSC
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.060 (1.52) SEATING
0.050 (1.27) PLANE
0.045 (1.14)
0.015 (0.38)
0.010 (0.25)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MO-095AG
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
24-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-24)
Dimensions shown in inches and (millimeters)
0.098 (2.49)
MAX
0.005 (0.13)
MIN
24
13
0.310 (7.87)
0.220 (5.59)
PIN 1
1
0.200 (5.08)
MAX
12
0.060 (1.52)
0.015 (0.38)
1.280 (32.51) MAX
0.320 (8.13)
0.290 (7.37)
0.150 (3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.100
(2.54)
BSC
0.070 (1.78) SEATING
PLANE
0.030 (0.76)
15
0
0.015 (0.38)
0.008 (0.20)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
–28–
REV. G
AD7710
OUTLINE DIMENSIONS
24-Lead Standard Small Outline Package [SOIC]
Wide Body
(R-24)
Dimensions shown in millimeters and (inches)
15.60 (0.6142)
15.20 (0.5984)
24
13
7.60 (0.2992)
7.40 (0.2913)
1
12
2.65 (0.1043)
2.35 (0.0925)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
ⴛ 45ⴗ
0.25 (0.0098)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
1.27 (0.0500)
BSC
0.51 (0.0201)
0.31 (0.0122)
8ⴗ
0ⴗ
SEATING
0.33
(0.0130)
PLANE
0.20 (0.0079)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013AD
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
REV. G
–29–
AD7710
Revision History
Location
Page
3/04—Data Sheet changed from REV. F to REV. G.
Changes to SPECIFICATIONS Note 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Deleted AD7710 to ADSP-2105 Interface section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Deleted Figure 19 and renumbered subsequent figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changes to AD7710 to 68HC11 Interface section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
–30–
REV. G
3/26/04 5:00 AM_MB
–31–
–32–
C01168-0-3/04(G)
Similar pages