AD AD7866BRU Dual 1 msps, 12-bit, 2-channel sar adc with serial interface Datasheet

Dual 1 MSPS, 12-Bit, 2-Channel
SAR ADC with Serial Interface
AD7866
FEATURES
Dual 12-Bit, 2-Channel ADC
Fast Throughput Rate: 1 MSPS
Specified for VDD of 2.7 V to 5.25 V
Low Power
11.4 mW Max at 1 MSPS with 3 V Supplies
24 mW Max at 1 MSPS with 5 V Supplies
Wide Input Bandwidth
70 dB SNR at 300 kHz Input Frequency
On-Board Reference 2.5 V
–40ⴗC to +125ⴗC Operation
Flexible Power/Throughput Rate Management
Simultaneous Conversion/Read
No Pipeline Delays
High Speed Serial Interface SPITM/QSPITM/
MICROWIRETM/DSP Compatible
Shutdown Mode: 1 ␮A Max
20-Lead TSSOP Package
GENERAL DESCRIPTION
The AD7866 is a dual 12-bit high speed, low power, successive
approximation ADC. The part operates from a single 2.7 V to
5.25 V power supply and features throughput rates up to 1 MSPS.
The device contains two ADCs, each preceded by a low noise,
wide bandwidth track-and-hold amplifier that can handle
input frequencies in excess of 10 MHz.
The conversion process and data acquisition are controlled
using standard control inputs, allowing easy interfacing to
microprocessors or DSPs. The input signal is sampled on the
falling edge of CS; conversion is also initiated at this point.
The conversion time is determined by the SCLK frequency.
There are no pipelined delays associated with the part.
The AD7866 uses advanced design techniques to achieve
very low power dissipation at high throughput rates. With 3 V
supplies and 1 MSPS throughput rate, the part consumes a
maximum of 3.8 mA. With 5 V supplies and 1 MSPS, the
current consumption is a maximum of 4.8 mA. The part also
offers flexible power/throughput rate management when
operating in sleep mode.
The analog input range for the part can be selected to be a 0 V
to VREF range or a 2 ⫻ VREF range with either straight binary or
twos complement output coding. The AD7866 has an on-chip
2.5 V reference that can be overdriven if an external reference
is preferred. Each on-board ADC can also be supplied with a
separate individual external reference.
FUNCTIONAL BLOCK DIAGRAM
DCAPA REF SELECT
VREF
2.5V
REF
VA1
VA2
MUX
DVDD
AD7866
BUF
T/H
AVDD
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
OUTPUT
DRIVERS
A0
RANGE
SCLK
CS
VDRIVE
CONTROL
LOGIC
VB1
VB2
MUX
T/H
DOUTA
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
OUTPUT
DRIVERS
DOUT B
BUF
AGND
AGND
DCAPB
DGND
PRODUCT HIGHLIGHTS
1. The AD7866 features two complete ADC functions, allowing
simultaneous sampling and conversion of two channels. Each
ADC has a 2-channel input multiplexer. The conversion result
of both channels is available simultaneously on separate data
lines, or may be taken on one data line if only one serial port
is available.
2. High Throughput with Low Power Consumption—The
AD7866 offers a 1 MSPS throughput rate with 11.4 mW
maximum power consumption when operating at 3 V.
3. Flexible Power/Throughput Rate Management—The conversion rate is determined by the serial clock, allowing the power
consumption to be reduced as the conversion time is reduced
through a SCLK frequency increase. Power efficiency can be
maximized at lower throughput rates if the part enters sleep
during conversions.
4. No Pipeline Delay—The part features two standard successive
approximation ADCs with accurate control of the sampling
instant via a CS input and once off conversion control.
The AD7866 is available in a 20-lead thin shrink small outline
(TSSOP) package.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
= T to T
on D
AD7866–SPECIFICATIONS (TExternal
A
MIN
MAX,
CAPA
Parameter
DYNAMIC PERFORMANCE
Signal to Noise + Distortion (SINAD) 2
Total Harmonic Distortion (THD) 2
Peak Harmonic or Spurious Noise (SFDR) 2
Intermodulation Distortion (IMD) 2
Second Order Terms
Third Order Terms
Channel-to-Channel Isolation
SAMPLE AND HOLD
Aperture Delay3
Aperture Jitter3
Aperture Delay Matching3
Full Power Bandwidth
DC ACCURACY
Resolution
Integral Nonlinearity
Differential Nonlinearity
0 V to VREF Input Range
Offset Error
Offset Error Match
Gain Error
Gain Error Match
2 VREF Input Range
Positive Gain Error
Zero Code Error
Zero Code Error Match
Negative Gain Error
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance
REFERENCE INPUT/OUTPUT
Reference Input Voltage
Reference Input Voltage Range 4
DC Leakage Current
Input Capacitance
Reference Output Voltage5
VREF Output Impedance6
Reference Temperature Coefficient
REF OUT Error (TMIN to TMAX)
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN3
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance 3
Output Coding
VDD = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, Reference = 2.5 V
and DCAPB, fSCLK = 20 MHz, unless otherwise noted.)
A Version1
B Version1
Unit
Test Conditions/Comments
68
–75
–76
68
–75
–76
dB min
dB max
dB max
fIN = 300 kHz Sine Wave, fS = 1 MSPS
fIN = 300 kHz Sine Wave, fS = 1 MSPS
fIN = 300 kHz Sine Wave, fS = 1 MSPS
–88
–88
–88
–88
–88
–88
dB typ
dB typ
dB typ
10
50
200
12
2
10
50
200
12
2
ns max
ps typ
ps max
MHz typ
MHz typ
12
± 1.5
–0.95/+1.25
12
±1
± 1.5
–0.95/+1.25
Bits
LSB max
LSB max
LSB max
±8
± 1.2
± 2.5
± 0.2
±8
± 1.2
± 2.5
± 0.2
LSB max
LSB typ
LSB max
LSB typ
± 2.5
±8
± 0.2
± 2.5
± 2.5
±8
± 0.2
± 2.5
LSB max
LSB max
LSB typ
LSB max
0 to VREF
0 to 2 VREF
± 500
1
30
10
0 to VREF
0 to 2 VREF
± 500
1
30
10
V
V
nA max
µA max
pF typ
pF typ
RANGE Pin Low upon CS Falling Edge
RANGE Pin High upon CS Falling Edge
TA = –40C to +85C
85C < TA ≤ 125C
When in Track
When in Hold
2.5
2/3
± 30
± 160
20
2.45/2.55
25
45
50
± 15
2.5
2/3
± 30
± 160
20
2.45/2.55
25
45
50
± 15
V
V min/V max
µA max
µA max
pF typ
V min/V max
Ω typ
Ω typ
ppm/°C typ
mV typ
± 1% for Specified Performance
REF SELECT Pin Tied High
VREF Pin
DCAPA, DCAPB Pins
0.7 VDRIVE
0.3 VDRIVE
±1
10
0.7 VDRIVE
0.3 VDRIVE
±1
10
V min
V max
µA max
pF max
VDRIVE – 0.2
VDRIVE – 0.2
0.4
0.4
±1
±1
10
10
Straight (Natural) Binary
Twos Complement
–2–
V min
V max
µA max
pF max
@ 3 dB
@ 0.1 dB
B Grade, 0 V to VREF Range Only; ±0.5 LSB typ
0 V to 2 VREF Range; ± 0.5 LSB typ
Guaranteed No Missed Codes to 12 Bits
Straight Binary Output Coding
–VREF to +VREF Biased about VREF with
Twos Complement Output Coding
VDD = 5 V
VDD = 3 V
Typically 15 nA, VIN = 0 V or VDRIVE
ISOURCE = 200 µA
ISINK = 200 µA
VDD = 2.7 V to 5.25 V
Selectable with Either Input Range
REV. A
AD7866
Parameter
A Version1
B Version1
Unit
Test Conditions/Comments
CONVERSION RATE
Conversion Time
Track/Hold Acquisition Time3
Throughput Rate
16
300
1
16
300
1
SCLK cycles
ns max
MSPS max
800 ns with SCLK = 20 MHz
2.7/5.25
2.7/5.25
2.7/5.25
2.7/5.25
V min/max
V min/max
3.1
3.1
mA max
2.8
2.8
mA max
4.8
4.8
mA max
3.8
3.8
mA max
Partial Power-Down Mode
1.6
1.6
mA max
Partial Power-Down Mode
560
560
µA max
Full Power-Down Mode
1
2
1
2
µA max
µA max
Digital I/Ps = 0 V or V DRIVE
VDD = 4.75 V to 5.25 V. Add 0.5 mA
Typical if Using Internal Reference.
VDD = 2.7 V to 3.6 V. Add 0.35 mA
Typical if Using Internal Reference.
VDD = 4.75 V to 5.25 V. Add 0.5 mA
Typical if Using Internal Reference.
VDD = 2.7 V to 3.6 V. Add 0.5 mA
Typical if Using Internal Reference.
fS = 100 kSPS, fSCLK = 20 MHz
Add 0.2 mA Typ if Using Internal
Reference.
(Static) Add 100 µA Typical if Using
Internal Reference.
SCLK On or Off. TA = –40C to +85C
SCLK On or Off. 85C < TA ≤ 125C
24
11.4
2.8
1.68
5
3
24
11.4
2.8
1.68
5
3
mW max
mW max
mW max
mW max
µW max
µW max
VDD = 5 V
VDD = 3 V
VDD = 5 V. SCLK On or Off.
VDD = 3 V. SCLK On or Off.
VDD = 5 V. SCLK On or Off.
VDD = 3 V. SCLK On or Off.
POWER REQUIREMENTS
VDD
VDRIVE
IDD7
Normal Mode (Static)
Operational, fS = 1 MSPS
Power Dissipation7
Normal Mode (Operational)
Partial Power-Down (Static)
Full Power-Down (Static)
NOTES
1
Temperature ranges as follows: A, B Versions: –40°C to +125°C.
2
See Terminology section.
3
Sample tested @ 25°C to ensure compliance.
4
External reference range that may be applied at V REF, DCAPA, or DCAPB.
5
Relates to pins V REF, DCAPA, or DCAPB.
6
See Reference section for D CAPA, DCAPB output impedances.
7
See Power vs. Throughput Rate section.
Specifications subject to change without notice.
REV. A
–3–
See Serial Interface Section
AD7866
TIMING SPECIFICATIONS1 (V
Parameter
fSCLK
2
DD
= 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V; TA = TMIN to TMAX, unless otherwise noted.)
Limit at
TMIN, TMAX
Unit
10
kHz min
20
MHz max
Description
16 tSCLK
ns max
tSCLK = 1/fSCLK
800
ns max
fSCLK = 20 MHz
tQUIET
50
ns max
Minimum Time between End of Serial Read and Next Falling Edge of CS
tCONVERT
t2
10
ns min
CS to SCLK Setup Time
t3 3
25
ns max
Delay from CS until DOUTA and DOUTB Three-State Disabled
3
40
ns max
0.4 tSCLK
0.4 tSCLK
10
25
10
50
ns min
ns min
ns min
ns max
ns min
ns max
Data Access Time after SCLK Falling Edge. VDRIVE 3 V, CL = 50 pF;
VDRIVE < 3 V, CL = 25 pF
SCLK Low Pulsewidth
SCLK High Pulsewidth
SCLK to Data Valid Hold Time
CS Rising Edge to DOUTA, DOUTB, High Impedance
SCLK Falling Edge to DOUTA, DOUTB, High Impedance
SCLK Falling Edge to DOUTA, DOUTB, High Impedance
t4
t5
t6
t7
t8 4
t9 4
NOTES
1
Sample tested at 25°C to ensure compliance. All input signals are specified with t R = tF = 5 ns (10% to 90% of V DRIVE) and timed from a voltage level of 1.6 V.
2
Mark/Space ratio for the CLK input is 40/60 to 60/40.
3
Measured with the load circuit of Figure 1 and defined as the time required for the output to cross 0.8 V or 2.0 V.
4
t8, t9 are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times t8 and t9 quoted in the timing characteristics are the true
bus relinquish times of the part and are independent of the bus loading.
Specifications subject to change without notice.
200␮A
TO
OUTPUT
PIN
IOL
1.6V
CL
50pF
200␮A
IOH
Figure 1. Load Circuit for Digital Output Timing Specifications
–4–
REV. A
AD7866
ABSOLUTE MAXIMUM RATINGS 1
Storage Temperature Range . . . . . . . . . . . . –65C to +150C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150C
TSSOP Package, Power Dissipation . . . . . . . . . . . . . 450 mW
JA Thermal Impedance (TSSOP) . . . . . . . . . . . . . 143C/W
JC Thermal Impedance (TSSOP) . . . . . . . . . . . . . . 45C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 kV
(TA = 25oC, unless otherwise noted.)
AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
DVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
VDRIVE to DGND . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V
VDRIVE to AGND . . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V
AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
Analog Input Voltage to AGND . . . . . –0.3 V to AVDD + 0.3 V
Digital Input Voltage to DGND . . . . . . . . . . . . –0.3 V to +7 V
VREF to AGND . . . . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V
Digital Output Voltage to DGND . . . –0.3 V to VDRIVE + 0.3 V
Input Current to Any Pin Except Supplies2 . . . . . . . . . 10 mA
Operating Temperature Range
Commercial (A, B Versions) . . . . . . . . . . . . . –40C to +125C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Transient currents of up to 100 mA will not cause SCR latch up.
ORDERING GUIDE
Model
Temperature Range
Resolution
(Bits)
AD7866ARU
AD7866BRU
EVAL-AD7866CB1
EVAL-CONTROL BRD22
–40°C to +125°C
–40°C to +125°C
12
12
Package Description
Thin Shrink SOC (TSSOP)
Thin Shrink SOC (TSSOP)
Evaluation Board
Controller Board
Package
Option
RU-20
RU-20
NOTES
1
This can be used as a standalone evaluation board or in conjunction with the evaluation board controller for evaluation/demonstration purposes.
2
This evaluation board controller is a complete unit, allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB design ators.
To order a complete evaluation kit, the particular ADC evaluation board, e.g., EVAL-AD7866CB, the EVAL-CONTROL BRD2, and a 12 V transformer must be
ordered. See relevant Evaluation Board Technical note for more information.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7866 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. A
–5–
AD7866
PIN CONFIGURATION
REF SELECT 1
20 A0
DCAPB 2
19 CS
AGND 3
18 SCLK
17 VDRIVE
VB2 4
VB1 5
AD7866
16 DOUTB
TOP VIEW 15 D
OUTA
(Not to Scale)
VA1 7
14 DGND
VA2 6
AGND 8
13 DVDD
DCAPA 9
12 AVDD
VREF 10
11 RANGE
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Function
1
REF SELECT
Internal/External Reference Selection. Logic input. If this pin is tied to GND, the on-chip 2.5 V reference
is used as the reference source for both ADC A and ADC B. In addition, pins VREF, DCAPA, and DCAPB
must be tied to decoupling capacitors. If the REF SELECT pin is tied to a logic high, an external reference can be supplied to the AD7866 through the VREF pin, in which case decoupling capacitors are
required on DCAPA and DCAPB. However, if the VREF pin is tied to AGND while REF SELECT is tied to
a logic low, an individual external reference can be applied to both ADC A and ADC B through pins
DCAPA and DCAPB, respectively. See the Reference Configuration Options section.
2, 9
DCAPB, DCAPA
Decoupling capacitors are connected to these pins to decouple the reference buffer for each respective
ADC. The on-chip reference can be taken from these pins and applied externally to the rest of a system.
Depending on the polarity of the REF SELECT pin and the configuration of the VREF pin, these
pins can also be used to input a separate external reference to each ADC. The range of the external
reference is dependent on the analog input range selected. See the Reference Configuration
Options section.
3, 8
AGND
Analog Ground. Ground reference point for all analog circuitry on the AD7866. All analog input signals
and any external reference signal should be referred to this AGND voltage. Both of these pins should
connect to the AGND plane of a system. The AGND and DGND voltages ideally should be at the
same potential and must not be more than 0.3 V apart, even on a transient basis.
4, 5
VB2, VB1
Analog Inputs of ADC B. Single-ended analog input channels. The input range on each channel is 0 V
to VREF or a 2 VREF range depending on the polarity of the RANGE pin upon the falling edge of CS.
6, 7
VA2, VA1
Analog Inputs of ADC A. Single-ended analog input channels. The input range on each channel is 0 V
to VREF or a 2 VREF range depending on the polarity of the RANGE pin upon the falling edge of CS.
10
VREF
Reference Decoupling and External Reference Selection. This pin is connected to the internal reference
and requires a decoupling capacitor. The nominal reference voltage is 2.5 V, which appears at the pin;
however, if the internal reference is to be used externally in a system, it must be taken from either the
DCAPA or DCAPB pins. This pin is also used in conjunction with the REF SELECT pin when
applying an external reference to the AD7866. See the REF SELECT pin description.
–6–
REV. A
AD7866
PIN FUNCTION DESCRIPTIONS (continued)
Pin No.
Mnemonic
Function
11
RANGE
Analog Input Range and Output Coding Selection. Logic input. The polarity on this pin will
determine what input range the analog input channels on the AD7866 will have, and will also select
the type of output coding the ADC will use for the conversion result. On the falling edge of CS, the
polarity of this pin is checked to determine the analog input range of the next conversion. If this pin
is tied to a logic low, the analog input range is 0 V to VREF and the output coding from the part will
be straight binary (for the next conversion). If this pin is tied to a logic high when CS goes low, the
analog input range is 2 VREF and the output coding for the part will be twos complement. However, if after the falling edge of CS the logic level of the RANGE pin has changed upon the eighth
SCLK falling edge, the output coding will change to the other option without any change in the
analog input range. (See the Analog Input and ADC Transfer Function sections.)
12
AVDD
Analog Supply Voltage, 2.7 V to 5.25 V. This is the only supply voltage for all analog circuitry on the
AD7866. The AVDD and DVDD voltages ideally should be at the same potential and must not be
more than 0.3 V apart even on a transient basis. This supply should be decoupled to AGND.
13
DVDD
Digital Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for all digital circuitry on the
AD7866. The DVDD and AVDD voltages should ideally be at the same potential and must not be
more than 0.3 V apart even on a transient basis. This supply should be decoupled to DGND.
14
DGND
Digital Ground. This is the ground reference point for all digital circuitry on the AD7866. The
DGND and AGND voltages ideally should be at the same potential and must not be more than 0.3 V
apart even on a transient basis.
15, 16
DOUTA, DOUTB
Serial Data Outputs. The data output is supplied to this pin as a serial data stream. The bits are
clocked out on the falling edge of the SCLK input. The data appears on both pins simultaneously
from the simultaneous conversions of both ADCs. The data stream consists of one leading zero
followed by three STATUS bits, followed by the 12 bits of conversion data. The data is provided
MSB first. If CS is held low for another 16 SCLK cycles after the conversion data has been output
on either DOUTA or DOUTB, the data from the other ADC follows on the DOUT pin. This allows data
from a simultaneous conversion on both ADCs to be gathered in serial format on either DOUTA or
DOUTB alone using only one serial port. See the Serial Interface section.
17
VDRIVE
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface
will operate. This pin should be decoupled to DGND.
18
SCLK
Serial Clock. Logic Input. A serial clock input provides the SCLK for accessing the data from the
AD7866. This clock is also used as the clock source for the conversion process.
19
CS
Chip Select. Active low logic input. This input provides the dual function of initiating conversions on
the AD7866 and frames the serial data transfer.
20
A0
Multiplexer Select. Logic input. This input is used to select the pair of channels to be converted
simultaneously, i.e., Channel 1 of both ADC A and ADC B, or Channel 2 of both ADC A and ADC B.
The logic state of this pin is checked upon the falling edge of CS, and the multiplexer is set up for
the next conversion. If it is low, the following conversion will be performed on Channel 1 of each ADC;
if it is high, the following conversion will be performed on Channel 2 of each ADC.
REV. A
–7–
AD7866
the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The
ratio is dependent on the number of quantization levels in the
digitization process; the more levels, the smaller the quantization noise. The theoretical signal-to-(noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point 1 LSB
below the first code transition, and full scale, a point 1 LSB above
the last code transition.
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Differential Nonlinearity
Thus, for a 12-bit converter, this is 74 dB.
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of harmonics to the fundamental. For the AD7866, it is defined as:
Offset Error
This applies to Straight Binary output coding. It is the deviation
of the first code transition (00 . . . 000) to (00 . . . 001) from the
ideal, i.e., AGND + 1 LSB.
THD (db) = 20 log
Offset Error Match
V22 +V32 +V42 + V52 + V62
V1
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
This is the difference in Offset Error between the two channels.
Gain Error
This applies to Straight Binary output coding. It is the deviation
of the last code transition (111 . . . 110) to (111 . . . 111) from
the ideal (i.e., VREF – 1 LSB) after the offset error has been
adjusted out.
Peak Harmonic or Spurious Noise
Peak harmonic, or spurious noise, is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum. But for ADCs
where the harmonics are buried in the noise floor, it will be a
noise peak.
Gain Error Match
This is the difference in Gain Error between the two channels.
Zero Code Error
This applies when using the twos complement output coding
option, in particular with the 2 VREF input range as –VREF to
+VREF biased about the VREF point. It is the deviation of the
midscale transition (all 1s to all 0s) from the ideal VIN voltage,
i.e., VREF – 1 LSB.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities will create distortion products
at sum and difference frequencies of mfa ± nfb where m, n = 0,
1, 2, 3, and so on. Intermodulation distortion terms are those for
which neither m nor n are equal to zero. For example, the second
order terms include (fa + fb) and (fa – fb), while the third order
terms include (2fa + fb), (2fa – fb), (fa + 2fb), and (fa – 2fb).
Zero Code Error Match
This refers to the difference in Zero Code Error between the
two channels.
Positive Gain Error
The AD7866 is tested using the CCIF standard where two
input frequencies near the top end of the input bandwidth are
used. In this case, the second order terms are usually distanced
in frequency from the original sine waves while the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified separately. The calculation of the intermodulation distortion is as
per the THD specification where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of the
sum of the fundamentals expressed in dB.
This applies when using the twos complement output coding
option, in particular with the 2 VREF input range as –VREF to
+VREF biased about the VREF point. It is the deviation of the last
code transition (011 . . . 110) to (011 . . . 111) from the ideal
(i.e., +V REF – 1 LSB) after the Zero Code Error has been
adjusted out.
Negative Gain Error
This applies when using the twos complement output coding
option, in particular with the 2 VREF input range as –VREF to
+VREF biased about the VREF point. It is the deviation of the first
code transition (100 . . . 000) to (100 . . . 001) from the ideal
(i.e., –V REF + 1 LSB) after the Zero Code Error has been
adjusted out.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between channels. It is measured by applying a full-scale
(2 VREF), 455 kHz sine wave signal to all unselected input
channels and determining how much that signal is attenuated in the
selected channel with a 10 kHz signal (0 V to VREF). The figure
given is the worst-case across all four channels for the AD7866.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns into track mode after the
end of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ± 1/2 LSB, after the end of conversion.
PSR (Power Supply Rejection)
See the Performance Curves section.
Signal-to-(Noise + Distortion) Ratio (SNDR)
This is the measured ratio of signal-to-(noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
–8–
REV. A
AD7866
Pf = power at frequency f in ADC output, and PfS = power at
frequency fS coupled onto the ADC AVDD supply. Here, a 100 mV
peak-to-peak sine wave is coupled onto the AVDD supply while the
digital supply is left unaltered. TPCs 3a and 3b show the PSRR
of the AD7866 when there is no decoupling on the supply, while
TPCs 4a and 4b show the PSRR with decoupling capacitors
of 10 µF and 0.1 µF on the supply.
PERFORMANCE CURVES
TPC 1 shows a typical FFT plot for the AD7866 at 1 MHz
sample rate and 300 kHz input frequency. TPC 2 shows the
signal-to-(noise + distortion) ratio performance versus input
frequency for various supply voltages while sampling at 1 MSPS
with an SCLK of 20 MHz.
TPCs 3a to 4b show the power supply rejection ratio versus
AVDD supply ripple frequency for the AD7866 under different
conditions. The power supply rejection ratio (PSRR) is defined
as the ratio of the power in the ADC output at full-scale frequency f, to the power of a 100 mV sine wave applied to the
ADC AVDD supply of frequency fS:
TPCs 5 and 6 show typical DNL and INL plots for the AD7866.
TPC 7 shows a graph of the total harmonic distortion versus
analog input frequency for various source impedances.
TPC 8 shows a graph of total harmonic distortion versus analog
input frequency for various supply voltages. See the Analog
Input section.
PSRR (dB ) = 10 log ( Pf PfS )
Typical Performance Characteristics
0
–15
100mV p-p SINE WAVE ON AVDD
2.5V EXT REFERENCE ON VREF
TA = 25ⴗC
–10
fIN = 300kHz
–20
SNR = 70.31dB
THD = –85.47dB
SFDR = –86.64dB
–30
PSRR – dB
–35
SNR – dB
0
4098 POINT FFT
fSAMPLE = 1MSPS
–55
–40
–50
VDD = 2.7V
VDD = 5.25V
–60
–75
–70
–80
–95
VDD = 4.75V
–90
–115
0
50
100
150
200 250 300 350
FREQUENCY – kHz
400
450
–100
500
1k
TPC 1. Dynamic Performance
–61
VDD = 3.6V
0
100mV p-p SINE WAVE ON AVDD
2.5V EXT REFERENCE ON DCAPA, DCAPB
TA = 25ⴗC
–10
–63
–20
VDD = VDRIVE = 2.7V
–30
PSRR – dB
SINAD – dB
–65
VDD = VDRIVE = 3.6V
–69
–71
–73
1M
TPC 3a. PSRR vs. Supply Ripple Frequency,
without Supply Decoupling
TA = 25 C
–67
10k
100k
AVDD RIPPLE FREQUENCY – Hz
–40
–50
–60
VDD = 5.25V
VDD = 2.7V
–70
VDD = VDRIVE = 5.25V
VDD = VDRIVE = 4.75V
–80
–90
–75
10k
VDD = 4.75V
100k
1k
INPUT FREQUENCY – Hz
TPC 2. SINAD vs. Input Frequency
REV. A
VDD = 3.6V
–100
1M
10k
100k
AVDD RIPPLE FREQUENCY – Hz
1M
TPC 3b. PSRR vs. Supply Ripple Frequency,
without Supply Decoupling
–9–
AD7866
1.0
0
100mV p-p SINE WAVE ON AVDD
2.5V EXT REFERENCE ON VREF
TA = 25ⴗC
–10
0.6
–30
0.4
–40
0.2
INL – LSB
PSRR – dB
–20
0.8
–50
–60
0.0
–0.2
VDD = 2.7V
–0.4
–70
–0.6
–80
VDD = 3.6V
–90
–0.8
–1.0
–100
10k
100k
AVDD RIPPLE FREQUENCY – Hz
1k
0
1M
500
1500
2000 2500
ADC – Code
3000
3500
4000
TPC 6. DC INL Plot
TPC 4a. PSRR vs. Supply Ripple Frequency,
with Supply Decoupling
–60
0
–20
RIN = 100⍀
TA = 25ⴗC
VDD = 4.75V
100mV p-p SINE WAVE ON AVDD
2.5V EXT REFERENCE ON DCAPA, DCAPB
TA = 25ⴗC
–10
–65
RIN = 50⍀
–30
–70
–40
THD – dB
PSRR – dB
1000
–50
VDD = 2.7V
–60
RIN = 10⍀
–75
–80
–70
–80
–85
VDD = 3.6V
–90
VDD = 4.75V
–90
10k
–100
10k
100k
AVDD RIPPLE FREQUENCY – Hz
1k
1M
1000k
TPC 7. THD vs. Analog Input Frequency
for Various Source Impedances
TPC 4b. PSRR vs. Supply Ripple Frequency,
with Supply Decoupling
–70
1.0
–72
0.8
–74
0.6
TA = 25ⴗC
VDD = VDRIVE = 2.7V
VDD = VDRIVE = 3.6V
–76
THD – dB
0.4
DNL – LSB
100k
INPUT FREQUENCY – Hz
0.2
0
–0.2
–78
–80
–82
–84
–0.4
VDD = VDRIVE = 5.25V
–86
–0.6
–88
–0.8
VDD = VDRIVE = 4.75V
–90
10k
100k
INPUT FREQUENCY – Hz
–1.0
0
500
1000
1500 2000 2500
ADC – Code
3000
3500
4000
1000k
TPC 8. THD vs. Analog Input Frequency
for Various Supply Voltages
TPC 5. DC DNL Plot
–10–
REV. A
AD7866
CIRCUIT INFORMATION
CAPACITIVE
DAC
The AD7866 is a fast, micropower, dual 12-bit, single supply,
A/D converter that operates from a 2.7 V to 5.25 V supply.
When operated from either a 5 V supply or a 3 V supply, the
AD7866 is capable of throughput rates of 1 MSPS when provided
with a 20 MHz clock.
A
VIN
SW1
CONTROL
LOGIC
B
SW2
COMPARATOR
The AD7866 contains two on-chip track-and-hold amplifiers,
two successive approximation A/D converters, and a serial interface with two separate data output pins, and is housed in a
20-lead TSSOP package, which offers the user considerable
space-saving advantages over alternative solutions. The serial
clock input accesses data from the part but also provides the
clock source for each successive approximation ADC. The analog input range for the part can be selected to be a 0 V to VREF
input or a 2 VREF input with either straight binary or twos
complement output coding. The AD7866 has an on-chip 2.5 V
reference that can be overdriven if an external reference is preferred. In addition, each ADC can be supplied with an individual
separate external reference.
The AD7866 also features power-down options to allow power
saving between conversions. The power-down feature is implemented across the standard serial interface, as described in the
Modes of Operation section.
CONVERTER OPERATION
The AD7866 has two successive approximation analog-to-digital
converters, each based around a capacitive DAC. Figures 2 and
3 show simplified schematics of one of these ADCs. The ADC
is comprised of control logic, a SAR, and a capacitive DAC, all
of which are used to add and subtract fixed amounts of charge
from the sampling capacitor to bring the comparator back into a
balanced condition. Figure 2 shows the ADC during its acquisition
phase. SW2 is closed and SW1 is in position A, the comparator
is held in a balanced condition, and the sampling capacitor
acquires the signal on VA1, for example.
AGND
Figure 3. ADC Conversion Phase
ANALOG INPUT
Figure 4 shows an equivalent circuit of the analog input structure
of the AD7866. The two diodes, D1 and D2, provide ESD
protection for the analog inputs. Care must be taken to ensure
that the analog input signal never exceeds the supply rails by more
than 300 mV. This will cause these diodes to become forwardbiased and start conducting current into the substrate. 10 mA is
the maximum current these diodes can conduct without causing
irreversible damage to the part. The capacitor C1 in Figure 4 is
typically about 10 pF and can primarily be attributed to pin
capacitance. The resistor R1 is a lumped component made up
of the on resistance of a switch. This resistor is typically about
100 Ω. The capacitor C2 is the ADC sampling capacitor and
has a capacitance of 20 pF typically. For ac applications, removing
high frequency components from the analog input signal is
recommended by use of an RC low-pass filter on the relevant
analog input pin. In applications where harmonic distortion and
signal-to-noise ratio are critical, the analog input should be driven
from a low impedance source. Large source impedances will
significantly affect the ac performance of the ADC. This may
necessitate the use of an input buffer amplifier. The choice of the
op amp will be a function of the particular application.
VDD
D1
R1
C2
VIN
CAPACITIVE
DAC
C1
D2
A
VIN
SW1
CONTROL
LOGIC
B
CONVERT PHASE – SWITCH OPEN
TRACK PHASE – SWITCH CLOSED
SW2
COMPARATOR
Figure 4. Equivalent Analog Input Circuit
AGND
Figure 2. ADC Acquisition Phase
When the ADC starts a conversion (see Figure 3), SW2 will
open and SW1 will move to position B, causing the comparator
to become unbalanced. The Control Logic and the capacitive
DAC are used to add and subtract fixed amounts of charge
from the sampling capacitor to bring the comparator back into a
balanced condition. When the comparator is rebalanced, the
conversion is complete. The Control Logic generates the ADC
output code. Figures 10 and 11 show the ADC transfer functions.
REV. A
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance will depend on the amount of total harmonic
distortion (THD) that can be tolerated. The THD will increase
as the source impedance increases, and performance will degrade
(see TPC 7).
–11–
AD7866
Analog Input Ranges
The analog input range for the AD7866 can be selected to be 0 V
to VREF or 2 VREF with either straight binary or twos complement
output coding. The RANGE pin is used to select both the analog
input range and the output coding, as shown in Figures 5 to 8.
On the falling edge of CS, point A, the logic level of the RANGE
pin is checked to determine the analog input range of the next
conversion. If this pin is tied to a logic low, the analog input
range will be 0 V to VREF and the output coding from the part will
be straight binary (for the next conversion). If this pin is at a logic
high when CS goes low, the analog input range will be 2 VREF and
the output coding for the part will be twos complement. However, if after the falling edge of CS, the logic level of the
RANGE pin has changed upon the eighth falling SCLK edge,
point B, the output coding will change to the other option without
any change in the analog input range. So for the next conversion,
twos complement output coding could be selected with a 0 V to
VREF input range, for example, if the RANGE pin is low upon
the falling edge of CS and high upon the eighth falling SCLK
edge, as shown in Figure 7. Figures 5 to 8 show examples of
timing diagrams for selections of different analog input ranges
with various output coding formats. Table I summarizes the
required logic level of the RANGE pin for each selection. Note
that the analog input range selected must not exceed VDD. The
logic input A0 is used to select the pair of channels to be converted
simultaneously. The logic state of this pin is also checked upon
the falling edge of CS, and the multiplexers are set up for the
next conversion. If it is low, the following conversion will be
performed on Channel 1 of each ADC; if it is high, the following
conversion will be performed on Channel 2 of each ADC.
Handling Bipolar Input Signals
Figure 9 shows how useful the combination of the 2 VREF
input range and the twos complement output coding scheme is
for handling bipolar input signals. If the bipolar input signal
is biased about VREF and twos complement output coding is
selected, then VREF becomes the zero code point, –VREF is
negative full-scale, and +VREF becomes positive full-scale with a
dynamic range of 2 VREF.
Transfer Functions
The designed code transitions occur at successive integer LSB
values (i.e., 1 LSB, 2 LSB, and so on). The LSB size is VREF/4096.
The ideal transfer characteristic for the AD7866 when straight
binary coding is selected is shown in Figure 10, and the ideal
transfer characteristic for the AD7866 when twos complement
coding is selected is shown in Figure 11.
Table I. Analog Input and Output Coding Selection
Range Level
@ Point A1
Range Level
@ Point B2
Input Range3
Output Coding3
Low
Low
0 V to VREF
Straight Binary
High
High
VREF ± VREF
Twos Complement
Low
High
VREF /2 ± VREF /2
Twos Complement
High
Low
0 V to 2 VREF
Straight Binary
NOTES
1
Point A = Falling edge of CS.
2
Point B = Eighth falling edge of SCLK.
3
Selected for next conversion.
A
B
CS
0V TO V
REF
INPUT RANGE
1
8
16
1
16
SCLK
RANGE
DOUTA
STRAIGHT BINARY
DOUTB
Figure 5. Selecting 0 V to VREF Input Range with Straight Binary Output Coding
A
B
CS
V
REF
ⴞV
REF
INPUT RANGE
1
8
16
1
16
SCLK
RANGE
DOUTA
TWOS COMPLEMENT
DOUTB
Figure 6. Selecting VREF ± VREF Input Range with Twos Complement Output Coding
–12–
REV. A
AD7866
A
B
CS
V
/2 ⴞ V
REF
/2
REF
INPUT RANGE
1
8
16
1
16
SCLK
RANGE
DOUTA
TWOS COMPLEMENT
DOUTB
Figure 7. Selecting VREF/2 ± VREF/2 Input Range with Twos Complement Output Coding
A
B
CS
0V TO 2 ⴛ V
REF
INPUT RANGE
1
8
16
1
16
SCLK
RANGE
DOUTA
STRAIGHT BINARY
DOUTB
Figure 8. Selecting 0 V to 2 VREF Input Range with Straight Binary Output Coding
VREF
VDD
100nF
VDD
REF SELECT
VREF
R4
470nF
V
DCAPA
VDRIVE
DSP/␮P
DCAPB
470nF
AD7866
R3
VIN
R2
0V
TWOS
COMPLEMENT
DOUT
V
R1
+VREF
(= 2 ⴛ VREF)
VREF
R1 = R2 = R3 = R4
–VREF
011
111
000
000
100
000
(= 0V)
Figure 9. Handling Bipolar Signals with the AD7866
1LSB = 2 ⴛ VREF/4096
011...111
011...110
ADC CODE
ADC CODE
111...111
111...110
111...000
1LSB = VREF/4096
011...111
100...010
100...001
100...000
000...010
000...001
000...000
0V
1LSB
ANALOG INPUT
–VREF + 1LSB
+VREF – 1LSB
VREF – 1LSB
ANALOG INPUT
VREF – 1LSB
Figure 10. Straight Binary Transfer
Characteristic with 0 V to VREF Input Range
REV. A
000...001
000...000
111...111
Figure 11. Twos Complement Transfer
Characteristic with VREF ± VREF Input Range
–13–
AD7866
Digital Inputs
The digital inputs applied to the AD7866 are not limited by the
maximum ratings that limit the analog inputs. Instead, the digital
inputs applied can go to 7 V and are not restricted by the VDD +
0.3 V limit as on the analog inputs. See maximum ratings.
470nF
DCAPA
AD7866
470nF
Another advantage of SCLK, RANGE, REF SELECT, A0, and
CS not being restricted by the VDD + 0.3 V limit is that power
supply sequencing issues are avoided. If one of these digital inputs
is applied before VDD, there is no risk of latch-up, as there
would be on the analog inputs if a signal greater than 0.3 V were
applied prior to VDD.
100nF
DCAPB
VREF
Figure 12. Relevant Connections when Using an
Internal Reference
DCAPA
VDRIVE
VREF
The AD7866 also has the VDRIVE feature, which controls the
voltage at which the serial interface operates. VDRIVE allows the
ADC to easily interface to both 3 V and 5 V processors. For
example, if the AD7866 was operated with a VDD of 5 V, the
VDRIVE pin could be powered from a 3 V supply, allowing a large
dynamic range with low voltage digital processors. For example,
the AD7866 could be used with the 2 VREF input range, with a
VDD of 5 V while still being able to interface to 3 V digital parts.
VREF REF SELECT
Figure 13. Relevant Connections when Applying
an External Reference at DCAP A and/or DCAP B
REFERENCE CONFIGURATION OPTIONS
470nF
The AD7866 has various reference configuration options. The
REF SELECT pin allows the choice of using an internal 2.5 V
reference or applying an external reference, or even an individual
external reference for each on-chip ADC if desired. If the REF
SELECT pin is tied to AGND, then the on-chip 2.5 V reference
is used as the reference source for both ADC A and ADC B. In
addition, pins VREF, DCAPA, and DCAPB must be tied to decoupling
capacitors (100 nF, 470 nF, and 470 nF recommended,
respectively). If the REF SELECT pin is tied to a logic high, an
external reference can be supplied to the AD7866 through the
VREF pin to overdrive the on-chip reference, in which case
decoupling capacitors are required on DCAPA and DCAPB again.
However, if the VREF pin is tied to AGND while REF SELECT
is tied to a logic low, an individual external reference can be
applied to both ADC A and ADC B through pins DCAPA and
DCAPB, respectively. Table II summarizes these reference options.
AD7866
DCAPB
470nF
VREF
DCAPA
AD7866
DCAPB
VREF
VDRIVE
REF SELECT
Figure 14. Relevant Connections when Applying
an External Reference at VREF
For specified performance, the last configuration was used with
the same reference voltage applied to both DCAPA and DCAPB.
The connections for the relevant reference pins are shown in the
typical connection diagrams. If the internal reference is being
used, the VREF pin should have a 100 nF capacitor connected to
AGND very close to the VREF pin. These connections are shown
in Figure 12.
Figure 13 shows the connections required when an external
reference is applied to DCAPA and DCAPB. In this example, the
same reference voltage is applied at each pin; however, a different
voltage may be applied at each of these pins for each on-chip
ADC. An external reference applied at these pins may have a
range from 2 V to 3 V, but for specified performance it must be
within ± 1% of 2.5 V. Figure 14 shows the third option, which is
to overdrive the internal reference through the VREF pin. This is
possible due to the series resistance from the VREF pin to the
internal reference. This external reference can have a range from
2 V to 3 V; but again, to get as close as possible to the specified
performance, a 2.5 V reference is desirable. DCAPA and DCAPB
decouple each on-chip reference buffer, as shown in Figure 15.
Table II. Reference Selection
Reference Option
REF SELECT
VREF1
DCAP A and DCAPB2
Internal
Externally through VREF
Externally through
DCAP A and/or DCAPB
Low
High
Decoupling Capacitor
External Reference
Decoupling Capacitor
Decoupling Capacitor
Low
AGND
External Reference A and/or
Reference B
NOTES
1
Recommended value of decoupling capacitor = 100 nF.
2
Recommended value of decoupling capacitor = 470 nF.
–14–
REV. A
AD7866
EXT REF
100nF
Normal Mode
EXT REF
VREF
DCAPA
This mode is intended for fastest throughput rate performance
since the user does not have to worry about any power-up times
with the AD7866 remaining fully powered all the time. Figure 16
shows the general diagram of the operation of the AD7866 in
this mode.
470nF
ADC A
2.5V
REF
BUF A
The conversion is initiated on the falling edge of CS, as described
in the Serial Interface section. To ensure that the part remains
fully powered up at all times, CS must remain low until at least
10 SCLK falling edges have elapsed after the falling edge of CS.
If CS is brought high any time after the 10th SCLK falling edge,
but before the 16th SCLK falling edge, the part will remain
powered up but the conversion will be terminated and DOUTA
and DOUTB will go back into three-state. Sixteen serial clock
cycles are required to complete the conversion and access the
conversion result. The DOUT line will not return to three-state
after 16 SCLK cycles have elapsed, but instead when CS is
brought high again. If CS is left low for another 16 SCLK cycles,
the result from the other ADC on board will also be accessed on
the same DOUT line, as shown in Figure 22 (see also the Serial
Interface section). The STATUS bits provided prior to each
conversion result will identify which ADC the following result
will be from. Once 32 SCLK cycles have elapsed, the DOUT line
will return to three-state on the 32nd SCLK falling edge. If CS is
brought high prior to this, the DOUT line will return to three-state
at that point. Thus, CS may idle low after 32 SCLK cycles, until
it is brought high again sometime prior to the next conversion
(effectively idling CS low), if so desired, since the bus will still
return to three-state upon completion of the dual result read.
ADC B
BUF B
DCAPB
470nF
EXT REF
Figure 15. Reference Circuit
If the on-chip 2.5 V reference is being used, and is to be applied
externally to the rest of the system, it may be taken from either
the VREF pin or one of the DCAPA or DCAPB pins. If it is taken
from the VREF pin, it must be buffered before being applied
elsewhere as it will not be capable of sourcing more than a few
microamps. If the reference voltage is taken from either the
DCAPA pin or DCAPB pin, a buffer is not strictly necessary. Either
pin is capable of sourcing current in the region of 100 µA; however, the larger the source current requirement, the greater the
voltage drop seen at the pin. The output impedance of each of
these pins is typically 50 Ω. In addition, this point represents
the actual voltage applied to the ADC internally so any voltage
drop due to the current load or disturbance due to a dynamic
load will directly affect the ADC conversion. For this reason, if a
large current source is necessary or a dynamic load is present, it
is recommended to use a buffer on the output to drive a device.
Once a data transfer is complete and DOUTA and DOUTB have
returned to three-state, another conversion can be initiated after
the quiet time, tQUIET, has elapsed by bringing CS low again.
Examples of suitable external reference devices that may be applied at pins VREF, DCAPA, or DCAPB are the AD780, REF192,
REF43, and AD1582.
Partial Power-Down Mode
MODES OF OPERATION
The mode of operation of the AD7866 is selected by controlling
the (logic) state of the CS signal during a conversion. There
are three possible modes of operation: normal mode, partial
power-down mode, and full power-down mode. The point at
which CS is pulled high after the conversion has been initiated
will determine which power-down mode, if any, the device will
enter. Similarly, if already in a power-down mode, CS can
control whether the device will return to normal operation or
remain in power-down. These modes of operation are designed
to provide flexible power management options. These options
can be chosen to optimize the power dissipation/throughput
rate ratio for differing application requirements.
This mode is intended for use in applications where slower
throughput rates are required. Either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and the ADC is then powered
down for a relatively long duration between these bursts of several
conversions. When the AD7866 is in partial power-down, all
analog circuitry is powered down except for the on-chip reference
and reference buffer.
To enter partial power-down, the conversion process must be
interrupted by bringing CS high anywhere after the second
falling edge of SCLK and before the tenth falling edge of SCLK
as shown in Figure 17. Once CS has been brought high in this
window of SCLKs, the part will enter partial power-down, the
conversion that was initiated by the falling edge of CS will be
CS
1
10
SCLK
DOUTA
DOUTB
STATUS BITS AND CONVERSION RESULT
Figure 16. Normal Mode Operation
REV. A
–15–
16
AD7866
terminated, and DOUTA and DOUTB will go back into threestate. If CS is brought high before the second SCLK falling
edge, the part will remain in normal mode and will not power
down. This will avoid accidental power-down due to glitches on
the CS line.
To exit this mode of operation and power up the AD7866 again,
a dummy conversion is performed. On the falling edge of CS,
the device will begin to power up, and will continue to power up
as long as CS is held low until after the falling edge of the tenth
SCLK. In the case of an external reference, the device will be
fully powered up once 16 SCLKs have elapsed, and valid data
will result from the next conversion, as shown in Figure 18. If
CS is brought high before the second falling edge of SCLK, the
AD7866 will again go into partial power-down. This avoids
accidental power-up due to glitches on the CS line; although the
device may begin to power up on the falling edge of CS, it will
power down again on the rising edge of CS. If the AD7866 is
already in partial power-down mode and CS is brought high
between the second and tenth falling edges of SCLK, the device
will enter full power-down mode. For more information on the
power-up times associated with partial power-down in various
configurations, see the Power-Up Times section.
Full Power-Down Mode
This mode is intended for use in applications where throughput
rates slower than those in the partial power-down mode are required,
as power-up from a full power-down takes substantially longer
than that from partial power-down. This mode is more suited to
applications where a series of conversions performed at a relatively high throughput rate would be followed by a long period
of inactivity and thus power-down. When the AD7866 is in full
power-down, all analog circuitry is powered down. Full powerdown is entered in a similar way as partial power-down, except
the timing sequence shown in Figure 17 must be executed twice.
The conversion process must be interrupted in a similar fashion
by bringing CS high anywhere after the second falling edge of
SCLK and before the tenth falling edge of SCLK. The device
will enter partial power-down at this point. To reach full
power-down, the next conversion cycle must be interrupted in
the same way, as shown in Figure 19. Once CS has been
brought high in this window of SCLKs, the part will power
down completely.
Note that it is not necessary to complete the 16 SCLKs once
CS has been brought high to enter a power-down mode.
To exit full power-down and power the AD7866 up again, a
dummy conversion is performed, as when powering up from
partial power-down. On the falling edge of CS, the device will
begin to power up and will continue to power up as long as CS
is held low until after the falling edge of the tenth SCLK. The
power-up time required must elapse before a conversion can be
initiated, as shown in Figure 20. See the Power-Up Times section for the power-up times associated with the AD7866.
POWER-UP TIMES
The AD7866 has two power-down modes, partial power-down
and full power-down, which are described in detail in the Modes
of Operation section. This section deals with the power-up time
required when coming out of either of these modes. It should be
noted that the power-up times quoted apply with the recommended
capacitors on the VREF, DCAPA, and DCAPB pins in place.
To power up from full power-down, approximately 4 ms should
be allowed from the falling edge of CS, shown in Figure 20 as
tPOWER UP. Powering up from partial power-down requires much
less time. If the internal reference is being used, the power-up
time is typically 4 µs; but if an external reference is being used,
the power-up time is typically 1 µs. This means that with any
frequency of SCLK up to 20 MHz, one dummy cycle will always
be sufficient to allow the device to power up from partial powerdown when using an external reference (see Figure 18). Once
the dummy cycle is complete, the ADC will be fully powered up
and the input signal will be acquired properly. A dummy cycle
may well be sufficient to power up the part when using an internal
reference also, provided the SCLK is slow enough to allow the
required power-up time to elapse before a valid conversion is
requested. In addition, it should be ensured that the quiet time,
tQUIET, has still been allowed from the point where the bus goes
back into three-state after the dummy conversion to the next
falling edge of CS. Alternatively, instead of slowing the SCLK to
make the dummy cycle long enough, the CS high time could
just be extended to include the required power-up time (as in
Figure 20) when powering up from full power-down.
Different power-up time is needed when coming out of partial
power-down for two cases where an internal or external reference is being used, primarily because of the on-chip reference
buffers. They power down in partial power-down mode and must
be powered up again if the internal reference is being used,
but they do not need to be powered up again if an external
reference is being used. The time needed to power up these
buffers is not just their own power-up time but also the time
required to charge up the decoupling capacitors present on pins
VREF, DCAPA, and DCAPB.
It should also be noted that during power-up from partial
power-down, the track-and-hold, which was in hold mode while
the part was powered down, returns to track mode after the first
SCLK edge the part receives after the falling edge of CS. This is
shown as point A in Figure 18.
When power supplies are first applied to the AD7866, the ADC
may power up in either of the power-down modes or the normal
mode. Because of this, it is best to allow a dummy cycle to elapse
to ensure that the part is fully powered up before attempting a
valid conversion. Likewise, if the part is to be kept in the partial
power-down mode immediately after the supplies are applied,
two dummy cycles must be initiated. The first dummy cycle must
hold CS low until after the tenth SCLK falling edge (see Figure 16);
in the second cycle, CS must be brought high before the tenth
SCLK edge but after the second SCLK falling edge (see Figure 17).
Alternatively, if the part is to be placed in full power-down
mode when the supplies have been applied, three dummy cycles
must be initiated. The first dummy cycle must hold CS low
until after the tenth SCLK falling edge (see Figure 16); the second and third dummy cycles place the part in full power-down
(see Figure 19). See also the Modes of Operation section.
Once supplies are applied to the AD7866, enough time must be
allowed for any external reference to power up and charge any
reference capacitor to its final value, or enough time must be
allowed for the internal reference buffer to charge the various
reference buffer decoupling capacitors to their final values.
–16–
REV. A
AD7866
Then, to place the AD7866 in normal mode, a dummy cycle
(1 µs to 4 µs approximately) should be initiated. If the first valid
conversion is performed directly after the dummy conversion,
care must be taken to ensure that adequate acquisition time has
been allowed. As mentioned earlier, when powering up from the
power-down mode, the part will return to track upon the first
SCLK edge applied after the falling edge of CS. However when
the ADC initially powers up after supplies are applied, the
track-and-hold will already be in track. This means that (assuming
one has the facility to monitor the ADC supply current and thus
determine which mode the AD7866 is in) if the ADC powers up
in the desired mode of operation and thus a dummy cycle is not
required to change mode, then neither is a dummy cycle required
to place the track-and-hold into track. If no current monitoring
facility is available, the relevant dummy cycle(s) should be
performed to ensure the part is in the required mode.
CS
1
2
10
16
SCLK
THREE-STATE
DOUTA
DOUTB
Figure 17. Entering Partial Power-Down Mode
THE PART MAY BE FULLY
POWERED UP; SEE POWER-UP
TIMES SECTION
THE PART BEGINS
TO POWER UP
CS
10
1
16
1
16
SCLK
A
DOUTA
INVALID DATA
DOUTB
VALID DATA
Figure 18. Exiting Partial Power-Down Mode
THE PART BEGINS
TO POWER UP
THE PART ENTERS
PARTIAL POWER-DOWN
THE PART ENTERS
FULL POWER-DOWN
CS
1
10
2
16
1
10
2
16
SCLK
THREE-STATE
DOUTA
THREE-STATE
INVALID DATA
DOUTB
INVALID DATA
Figure 19. Entering Full Power-Down Mode
THE PART IS
FULLY POWERED UP
THE PART BEGINS
TO POWER UP
tPOWER UP
CS
1
10
16
1
16
SCLK
DOUTA
DOUTB
INVALID DATA
VALID DATA
Figure 20. Exiting Full Power-Down Mode
REV. A
–17–
AD7866
can be said to dissipate 24 mW for 2 µs during each conversion
cycle. For the remainder of the conversion cycle, 8 µs, the part
remains in partial power-down mode. The AD7866 can be said to
dissipate 2.8 mW for the remaining 8 µs of the conversion cycle.
If the throughput rate is 100 kSPS, the cycle time is 10 µs and the
average power dissipated during each cycle is (2/10) (24 mW) +
(8/10) (2.8 mW) = 7.04 mW. If VDD = 3 V, SCLK = 20 MHz,
and the device is again in partial power-down mode between
conversions, the power dissipated during normal operation is
11.4 mW. The AD7866 can be said to dissipate 11.4 mW for 2 µs
during each conversion cycle and 1.68 mW for the remaining 8 µs
when the part is in partial power-down. With a throughput rate of
100 kSPS, the average power dissipated during each conversion
cycle is (2/10) (11.4 mW) + (8/10) (1.68 mW) = 3.624 mW.
Figure 21 shows the maximum power versus throughput rate
when using the partial power-down mode between conversions
with both 5 V and 3 V supplies for the AD7866.
POWER VS. THROUGHPUT RATE
When the AD7866 is in partial power-down mode and not
converting, the average power consumption of the ADC decreases
at lower throughput rates. Figure 21 shows that as the throughput rate is reduced, the part remains in its partial power-down
state longer, and the average power consumption over time
drops accordingly.
100
VDD = 5V
SCLK = 20MHz
POWER – mW
10
VDD = 3V
SCLK = 20MHz
1
0.1
SERIAL INTERFACE
Figure 22 shows the detailed timing diagram for serial interfacing
to the AD7866. The serial clock provides the conversion clock
and controls the transfer of information from the AD7866
during conversion.
0.01
50
0
100
150
200
250
300
350
THROUGHPUT – kSPS
The CS signal initiates the data transfer and conversion process.
The falling edge of CS puts the track-and-hold into hold mode
and takes the bus out of three-state; the analog input is sampled
at this point. The conversion is also initiated at this point and
requires 16 SCLK cycles to complete. Once 13 SCLK falling
edges have elapsed, the track-and-hold will go back into track
on the next SCLK rising edge, as shown in Figure 22 at point
B. On the rising edge of CS, the conversion will be terminated
and DOUTA and DOUTB will go back into three-state. If CS is
not brought high but is instead held low for a further 16 SCLK
cycles on DOUTA, the data from conversion B will be output on
Figure 21. Power vs. Throughput for Partial Power-Down
For example, if the AD7866 is operated in a continuous sampling
mode with a throughput rate of 100 kSPS and an SCLK of
20 MHz (VDD = 5 V), and the device is placed in partial powerdown mode between conversions, the power consumption is
calculated as follows. The maximum power dissipation during
normal operation is 24 mW (VDD = 5 V). If the power-up time
allowed from partial power-down is one dummy cycle, i.e., 1 µs,
(assuming use of an external reference) and the remaining
conversion time is another cycle, i.e., 1 µs, then the AD7866
CS
t6
t2
1
SCLK
2
3
4
DOUTB
THREESTATE
0
13
RANGE
A0
A/B
14
15
t5
t7
t4
t3
DOUTA
B
5
16
t8
t QUIET
DB11
DB2
DB10
DB1
DB0
THREESTATE
1 LEADING ZERO
3 STATUS BITS
Figure 22. Serial Interface Timing Diagram
CS
t6
t2
2
1
SCLK
3
4
5
14
15
32
17
16
t5
t3
DOUTA
THREESTATE
0
RANGE
t4
A0/ A0
1 LEADING ZERO
3 STATUS BITS
ZERO
DB11A
t9
t7
DB1A
DB0A
ZERO
RANGE
A0/ A0
ONE
DB11B
DB1B
DB0B
THREESTATE
1 LEADING ZERO
3 STATUS BITS
Figure 23. Reading Data from Both ADCs on One DOUT Line
–18–
REV. A
AD7866
Table III. STATUS Bit Description
Bit
Bit Name
Comment
15
14
ZERO
RANGE
Leading Zero. This bit will always be a zero output.
The polarity of this bit reflects the analog input range that has been selected with the RANGE pin.
If it is a 0, it means that in the previous transfer upon the falling edge of the CS, the range pin was
at a logic low, providing an analog input range from 0 V to VREF for this conversion. If it is a 1, it
means that in the previous transfer upon the falling edge of CS, the RANGE pin was at a logic high,
resulting in an analog input range of 2 VREF selected for this conversion. See Analog Input section.
13
A0
12
A/B
This bit indicates on which channel the conversion is being performed, Channel 1 or Channel 2 of
the ADC in question. If this bit is a 0, the conversion result will be from Channel 1 of the ADC;
if it is a 1, the result will be from Channel 2 of the ADC in question.
This bit indicates from which ADC the conversion result comes. If this bit is a 0, the result is from ADC A;
if it is a 1, the result is from ADC B. This is especially useful if only one serial port is available for
use and one DOUT line is used, as shown in Figure 23.
DOUTA. Likewise, if CS is held low for a further 16 SCLK cycles
on DOUTB, the data from conversion A will be output on DOUTB.
This is illustrated in Figure 23 where the case for DOUTA is shown.
Note that in this case, the DOUT line in use will go back into
three-state on the 32nd SCLK rising edge or the rising edge of CS,
whichever occurs first.
The SPORT0 control register should be set up as follows:
Sixteen serial clock cycles are required to perform the conversion
process and to access data from one conversion on either data
line of the AD7866. CS going low provides the leading zero to
be read in by the microcontroller or DSP. The remaining data is
then clocked out by subsequent SCLK falling edges, beginning
with the first of three data STATUS bits. Thus the first falling
clock edge on the serial clock has the leading zero provided and
also clocks out the first of three STATUS bits. The final bit in
the data transfer is valid on the sixteenth falling edge, having
being clocked out on the previous (fifteenth) falling edge. In
applications with a slower SCLK, it is possible to read in data on
each SCLK rising edge, i.e., the first rising edge of SCLK after
the CS falling edge would have the leading zero provided and
the fifteenth rising SCLK edge would have DB0 provided. The
three STATUS bits that follow the leading zero provide information with respect to the conversion result that follows them
on the DOUT line in use. Table III shows how these identification bits can be interpreted.
MICROPROCESSOR INTERFACING
The serial interface on the AD7866 allows the parts to be directly
connected to a range of many different microprocessors. This
section explains how to interface the AD7866 with some of the
more common microcontroller and DSP serial interface protocols.
AD7866 to ADSP-218x
The ADSP-218x family of DSPs is directly interfaced to the
AD7866 without any glue logic required. The VDRIVE pin of the
AD7866 takes the same supply voltage as that of the ADSP-218x.
This allows the ADC to operate at a higher supply voltage than
the serial interface, i.e., ADSP-218x, if necessary. This example
shows both DOUT A and DOUT B of the AD7866 connected to
both serial ports of the ADSP-218x.
REV. A
TFSW = RFSW = 1, Alternate Framing
INVRFS = INVTFS = 1, Active Low Frame Signal
DTYPE = 00, Right Justify Data
SLEN = 1111, 16-Bit Data-Words
ISCLK = 1, Internal Serial Clock
TFSR = RFSR = 1, Frame Every Word
IRFS = 0
ITFS = 1
The SPORT1 control register should be set up as follows:
TFSW = RFSW = 1, Alternate Framing
INVRFS = INVTFS = 1, Active Low Frame Signal
DTYPE = 00, Right Justify Data
SLEN = 1111, 16-Bit Data-Words
ISCLK = 0, External Serial Clock
TFSR = RFSR = 1, Frame Every Word
IRFS = 0
ITFS = 1
To implement the power-down modes on the AD7866, SLEN
should be set to 1001 to issue an 8-bit SCLK burst. The
connection diagram is shown in Figure 24. The ADSP-218x has
the TFS0 and RFS0 of the SPORT0 and the RFS1 of SPORT1
tied together, with TFS0 set as an output and both RFS0 and RFS1
set as inputs. The DSP operates in alternate framing mode and
the SPORT control register is set up as described. The frame
synchronization signal generated on the TFS is tied to CS and,
as with all signal processing applications, equidistant sampling is
necessary. However, in this example, the timer interrupt is used to
control the sampling rate of the ADC and under certain conditions,
equidistant sampling may not be achieved.
The timer and other registers are loaded with a value that will
provide an interrupt at the required sample interval. When an
interrupt is received, a value is transmitted with TFS/DT (ADC
control word). The TFS is used to control the RFS and therefore the reading of data. The frequency of the serial clock is set
in the SCLKDIV register. When the instruction to transmit with
TFS is given (i.e., AX0 = TX0), the state of the SCLK is
checked. The DSP will wait until the SCLK has gone high, low,
and high before transmission will start. If the timer and SCLK
values are chosen such that the instruction to transmit occurs on
or near the rising edge of SCLK, the data may be transmitted or
it may wait until the next clock edge.
–19–
AD7866
For example, if the ADSP-2189 had a 20 MHz crystal such that it
had a master clock frequency of 40 MHz, then the master cycle
time would be 25 ns. If the SCLKDIV register is loaded with the
value 3, an SCLK of 5 MHz is obtained and eight master clock
periods will elapse for every 1 SCLK period. Depending on the
throughput rate selected, if the timer register were loaded with the
value, 803, (803 + 1 = 804), for example, 100.5 SCLKs would
occur between interrupts and subsequently between transmit
instructions. This situation would result in nonequidistant
sampling as the transmit instruction is occurring on an SCLK
edge. If the number of SCLKs between interrupts were a whole
integer figure of N, equidistant sampling would be implemented
by the DSP.
ADSP-218x*
AD7866*
SCLK
SCLK0
SCLK1
CS
TFS0
RFS0
RSF1
DOUTA
DR0
DOUTB
DR1
VDD
Figure 24. Interfacing the AD7866 to the ADSP-218x
AD7866*
TMS320C541*
SCLK
AD7866 to DSP-563xx
The connection diagram in Figure 26 shows how the AD7866
can be connected to the ESSI (synchronous serial interface) of
the DSP-563xx family of DSPs from Motorola. Each ESSI
(there are two on-board) is operated in synchronous mode
(bit SYN = 1 in CRB register) with internally generated word
length frame sync for both Tx and Rx (bits FSL1 = 0 and FSL0 = 0
in CRB). Normal operation of the ESSI is selected by making
MOD = 0 in the CRB. Set the word length to 16 by setting bits
WL1 = 1 and WL0 = 0 in CRA. To implement the power-down
modes on the AD7866, the word length can be changed to eight
bits by setting bits WL1 = 0 and WL0 = 0 in CRA. The FSP bit
in the CRB should be set to 1 to make the frame sync negative.
It should be noted that for signal processing applications, it is
imperative that the frame synchronization signal from the
DSP-563xx provide equidistant sampling.
In the example shown in Figure 26, the serial clock is taken from
the ESSI0, so the SCK0 pin must be set as an output, SCKD = 1,
while the SCK1 pin is set up as an input, SCKD = 0. The frame
sync signal is taken from SC02 on ESSI0, so SCD2 = 1, while
on ESSI1, SCD2 = 0, so SC12 is configured as an input. The
VDRIVE pin of the AD7866 takes the same supply voltage as that
of the DSP-563xx. This allows the ADC to operate at a higher
voltage than the serial interface, i.e., DSP-563xx, if necessary.
VDRIVE
*ADDITIONAL PINS OMITTED
FOR CLARITY
The connection diagram is shown in Figure 25. It should be noted
that for signal processing applications, it is imperative that the
frame synchronization signal from the TMS320C541 will provide
equidistant sampling. The VDRIVE pin of the AD7866 takes the
same supply voltage as that of the TMS320C541. This allows the
ADC to operate at a higher voltage than the serial interface, i.e.,
TMS320C541, if necessary.
CLKX0
AD7866*
CLKR0
CLKX1
DSP-563xx*
SCLK
CLKR1
SCK0
SCK1
DOUTA
DR0
DOUTB
DR1
DOUTA
SRD0
FSX0
DOUTB
SRD1
CS
SC02
CS
VDRIVE
FSR0
FSR1
SC12
*ADDITIONAL PINS OMITTED
FOR CLARITY
VDRIVE
VDD
Figure 25. Interfacing the AD7866 to the TMS320C541
*ADDITIONAL PINS OMITTED
FOR CLARITY
AD7866 to TMS320C541
The serial interface on the TMS320C541 uses a continuous serial
clock and frame synchronization signals to synchronize the data
transfer operations with peripheral devices like the AD7866. The
CS input allows easy interfacing between the TMS320C541 and
the AD7866 with no glue logic required. The serial ports of
the TMS320C541 are set up to operate in burst mode with internal
CLKX (Tx serial clock on serial port 0) and FSX0 (Tx frame sync
from serial port 0). The serial port control (SPC) registers must have
the following setup:
SPC0: FO = 0, FSM = 1, MCM = 1 and TxM = 1
SPC1: FO = 0, FSM = 1, MCM = 0 and TxM = 0
The format bit, FO, may be set to 1 to set the word length to
eight bits, in order to implement the power-down modes on the AD7866.
VDD
Figure 26. Interfacing to the DSP-563xx
APPLICATION HINTS
Grounding and Layout
The analog and digital supplies to the AD7866 are independent
and separately pinned out to minimize coupling between the analog
and digital sections of the device. The AD7866 has very good
immunity to noise on the power supplies as can be shown by the
PSRR vs. Supply Ripple Frequency plots, TPC 3a to TPC 4b.
However, care should be taken with regard to grounding and
layout.
The printed circuit board that houses the AD7866 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can be easily separated. A minimum
–20–
REV. A
AD7866
etch technique is generally best for ground planes because it gives
the best shielding. Both AGND pins of the AD7866 should be
sunk in the AGND plane. Digital and analog ground planes
should be joined at only one place. If the AD7866 is in a system
where multiple devices require an AGND to DGND connection, the connection should still be made at one point only,
a star ground point that should be established as close as
possible to the AD7866.
Avoid running digital lines under the device since these will
couple noise onto the die. The analog ground plane should be
allowed to run under the AD7866 to avoid noise coupling.
The power supply lines to the AD7866 should use the largest
trace possible to provide low impedance paths and to reduce the
effects of glitches on the power supply line. Fast switching signals
like clocks should be shielded with digital ground to avoid
radiating noise to other sections of the board, and clock signals
should never be run near the analog inputs. Avoid crossover of
digital and analog signals. Traces on opposite sides of the board
should run at right angles to each other. This will reduce the
effects of feedthrough through the board. A microstrip technique
is by far the best but is not always possible with a double-sided
board. For this technique, the component side of the board is
dedicated to ground planes while signals are placed on the
solder side.
Good decoupling is also important. All analog supplies should be
decoupled with 10 µF tantalum in parallel with 0.1 µF capacitors
to AGND. All digital supplies should have at least a 0.1 µF disk
ceramic capacitor to DGND. VDRIVE should have a 0.1 µF ceramic
capacitor to DGND. To achieve the best results from these
decoupling components, place them as close as possible to the
device, ideally right up against it. The 0.1 µF capacitors should
REV. A
be common ceramic or surface-mount types, which have low
Effective Series Resistance (ESR) and Effective Series Inductance
(ESI), and provide a low impedance path to ground at high
frequencies for handling transient currents due to internal logic
switching. Figure 27 shows the recommended supply decoupling
scheme. For information on the decoupling requirements of each
reference configuration, see the Reference Configuration
Options section.
10␮F
AVDD
DVDD
AGND
AGND
DGND
0.1␮F
0.1␮F
10␮F
VDRIVE
AD7866
0.1␮F
Figure 27. Recommended Supply Decoupling Scheme
Evaluating the AD7866 Performance
The recommended layout for the AD7866 is outlined in the
evaluation board for the AD7866. The evaluation board package
includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from the PC via the
eval-controller board. The eval-controller board can be used in
conjunction with the AD7866 evaluation board, as well as many
other Analog Devices evaluation boards ending in the CB designator, to demonstrate/evaluate the ac and dc performance of the
AD7866.
The software allows the user to perform ac (fast Fourier transform)
and dc (histogram of codes) tests on the AD7866.
–21–
AD7866
OUTLINE DIMENSIONS
20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
6.60
6.50
6.40
20
11
4.50
4.40
4.30
1
6.40 BSC
10
PIN 1
0.65
BSC
0.15
0.05
0.30
COPLANARITY 0.19
0.10
1.20
MAX
0.20
0.09
SEATING
PLANE
8ⴗ
0ⴗ
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153AC
–22–
REV. A
AD7866
Revision History
Location
Page
2/03—Data Sheet changed from REV. 0 to REV. A.
Addition to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Addition to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Added text to Analog Input Ranges section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Changes to Figure 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Changes to POWER VS. THROUGHPUT RATE section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Replaced Figure 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
REV. A
–23–
–24–
PRINTED IN U.S.A.
C02672–0–2/03(A)
Similar pages