AD AD8321ARZ2 Gain programmable catv line driver Datasheet

a
APPLICATIONS
Gain Programmable Line Driver
HFC High Speed Data Modems
Interactive CATV Set-Top Boxes
CATV Plant Test Equipment
General Purpose IF Variable Gain Block
DESCRIPTION
The AD8321 is a low cost digitally controlled variable gain
amplifier optimized for coaxial line driving applications such as
cable modems that are designed to the DOCSIS* (upstream)
standard. An 8-bit serial word determines the desired output gain
over a 53.4 dB range, resulting in gain changes of 0.75 dB/LSB.
The AD8321 comprises a digitally controlled variable attenuator
of 0 dB to –53.4 dB, which is preceded by a low noise, fixed
gain buffer and followed by a low distortion high power ampli­
fier. The AD8321 accepts a differential or single-ended input
signal. The output is specified for driving a 75 W load, such as
coaxial cable, although the AD8321 is capable of driving other
loads. Performance of –53 dBc is achieved with an output level
up to 11 dBm at 42 MHz bandwidth using a 9 V supply.
A key performance and cost advantage of the AD8321 results
from the ability to maintain a constant 75 W output impedance
during power-up and power-down conditions. This eliminates
the need for external 75 W termination, resulting in twice the
effective output voltage when compared to a standard opera­
tional amplifier, thus eliminating the need for a transformer.
FUNCTIONAL BLOCK DIAGRAM
VCC
GND
PWR
AMP
AD8321
VOUT
VIN+
INV
REVERSE
AMP
ATTENUATOR CORE
VIN–
DATA LATCH
DATA SHIFT REGISTER
POWERDOWN/
SWITCH
INTER
DATA SHIFT REGISTER
DATEN CLK
PD
SDATA
The AD8321 is packaged in a low cost 20-lead SOIC, operates
from a single +9 V supply, and has an operational temperature
range of –40∞C to +85∞C.
–40
fO = 42MHz
VIN = 137mV p-p
(PIN = –15dBm)
(POUT = 11dBm @
MAX GAIN)
–50
DISTORTION – dBc
FEATURES
Linear in dB Gain Response Over >53 dB Range
Drives Low Distortion >11 dBm Signal into 75 � Load:
–53 dBc SFDR at 42 MHz
Very Low Output Noise Level
Maintains Constant 75 � Output Impedance
Power-Up and Power-Down Condition
No Line Transformer Required
Upper Bandwidth: 235 MHz (Min Gain)
9 V Single Supply Operation
Power-Down Functionality
Supports SPI Interface
Low Cost
Gain Programmable
CATV Line Driver
AD8321
–60
HD3
–70
HD2
–80
–90
0
8
16
24
32
40
48
GAIN CONTROL – Decimal
56
64
72
Figure 1. Harmonic Distortion vs. Gain Control
*Data-Over-Cable Service Interface Specifications
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/461-3113
© 2005 Analog Devices, Inc. All rights reserved.
(@ VCC = +9 V, TA = +25�C, VIN = 0.137 V p-p, single-ended input, RL = 75 �, RIN =
AD8321–SPECIFICATIONS 75 � unless otherwise noted)
Parameter
INPUT CHARACTERISTICS
Specified AC Voltage
Noise Figure
Input Resistance
Conditions
Min
Output = 11 dBm, Max Gain
Max Gain, f = 10 MHz
Single-Ended Input
Differential Input
52.4
25.25
–28.15
OUTPUT CHARACTERISTICS
Bandwidth (–3 dB)
Bandwidth Roll-Off
Bandwidth Peaking
Output Offset Voltage
Output Noise Spectral Density
All Gain Codes
f = 65 MHz
f = 65 MHz
All Gain Codes, Full Temperature Range
Max Gain, f = 10 MHz
Min Gain, f = 10 MHz
Output Noise Temperature Sensitivity 0 £ TA £ +70∞C, Min Gain
Power-Down Spectral Density
1 dB Compression Point
Max Gain, f = 10 MHz
Output Impedance
Power-Up and Power-Down
OVERALL PERFORMANCE
Worst Harmonic Distortion
Distortion Temperature Sensitivity
Gain Accuracy
Gain Temperature Sensitivity
Output Settling to 1 mV
Gain Change @ TDATEN = 1
Input Change
Signal Feedthrough
POWER CONTROL
Power-Down Settling Time to 1 mV
Power-Up Settling Time to 1 mV
Power-Up/Down Pedestal Offset
Power-Up/Down Glitch
POWER SUPPLY
Quiescent Current
Max
0.137
15
820
900
2.0
Input Capacitance
GAIN CONTROL INTERFACE
Gain Range
Maximum Gain
Minimum Gain
Gain Scaling Factor
Typ
60
53.4
26
–27.4
0.7526
120
0.8
0
± 30
60
20
0.02
1
19.5
75
Unit
V p-p
dB
W
W
pF
54.4
26.75
–26.4
90
dB
dB
dB
dB/LSB
MHz
dB
dB
mV
nV/÷Hz
nV/÷Hz
nV/÷Hz/∞C
nV/÷Hz
dBm
W
f = 42 MHz, POUT = 11 dBm, VCC = +9 V
f = 65 MHz, POUT = 11 dBm, VCC = +9 V
–40∞C £ TA £ +85∞C
f = 10 MHz, All Gain Codes
0 £ TA £ +70∞C
–53
–51
0.03
± 0.2
0.004
dBc
dBc
dBc/∞C
dB
dB/∞C
Min to Max Gain, VIN = 0 V
Max Gain, VIN = 0.15 V Step
Power Down, 65 MHz, Min Gain
VIN = 0.137 V p-p
60
30
–80
ns
ns
dBc
Max Gain, VIN = 0
Max Gain, VIN = 0
Max Gain, VIN = 0
Max Gain, VIN = 0
40
300
± 30
40
ns
ns
mV
mV p-p
Power-Up, VCC = +9 V
Power-Down, VCC = +9 V
82
45
90
52
97
60
mA
mA
Specifications subject to change without notice.
–2–
REV. A
AD8321
LOGIC INPUTS (TTL/CMOS Logic) (DATEN, CLK, SDATA, V
= +9 V; Full Temperature Range)
CC
Parameter
Min
Logic “1” Voltage
Logic “0” Voltage
Logic “1” Current (VINH = 5 V) CLK, SDATA, DATEN
Logic “0” Current (VINL = 0 V) CLK, SDATA, DATEN
Logic “1” Current (VINH = 5 V) PD
Logic “0” Current (VINL = 0 V) PD
2.1
0
0
–600
50
–250
TIMING REQUIREMENTS (Full Temperature Range, V
CC
Typ
Min
Clock Pulsewidth (TWH)
Clock Period (TC)
Setup Time SDATA vs. Clock (TDS)
Setup Time DATEN vs. Clock (TES)
Hold Time SDATA vs. Clock (TDH)
Hold Time DATEN vs. Clock (TEH)
Input Rise and Fall Times, SDATA, DATEN, Clock (TR, TF)
16.0
32.0
5.0
15.0
5.0
3.0
Typ
Specifications subject to change without notice.
TDS
VALID DATA WORD G1
MSB. . . .LSB
VALID DATA WORD G2
TC
TWH
CLK
TES
TEH
8 CLOCK CYCLES
DATEN
GAIN TRANSFER (G1)
GAIN TRANSFER (G2)
TOFF
PD
TGS
TON
ANALOG
OUTPUT
PEDESTAL
SIGNAL AMPLITUDE (p-p)
Figure 2. Serial Interface Timing
VALID DATA BIT
SDATA MSB
MSB-1
TDS
MSB-2
TDH
CLK
Figure 3. SDATA Timing
REV. A
Unit
5.0
0.8
20
–100
190
–30
V
V
nA
nA
mA
mA
= +9 V, TR = TF = 4 ns, fCLK = 8 MHz unless otherwise noted.)
Parameter
SDATA
Max
–3–
Max
Unit
10
ns
ns
ns
ns
ns
ns
ns
AD8321
ABSOLUTE MAXIMUM RATINGS*
PIN CONFIGURATION
Supply Voltage +VS
Pins 7, 8, 9, 17, 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . +11 V
Input Voltages
Pins 18, 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 V
Pins 1, 2, 3, 6 . . . . . . . . . . . . . . . . . . . . . . . –0.8 V to +5.5 V
Internal Power Dissipation
Small Outline (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.90 W
Operating Temperature Range . . . . . . . . . . . –40∞C to +85∞C
Storage Temperature Range . . . . . . . . . . . . –65∞C to +150∞C
Lead Temperature, Soldering 60 seconds . . . . . . . . . . +300∞C
SDATA 1
20
VCC
CLK 2
19
VIN–
DATEN 3
18
VIN+
GND 4
17
VCC
16
GND
BYP1 5
AD8321
TOP VIEW 15 GND
(Not to Scale)
14 BYP2
VCC 7
PD 6
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
VCC 8
13
GND
VCC 9
12
GND
VOUT 10
11
GND
ORDERING GUIDE
Model
Temperature Range
AD8321AR
AD8321AR-REEL
AD8321ARZ2
AD8321ARZ-REEL2
AD8321-EVAL
1
2
–40∞C to +85∞C
–40∞C to +85∞C
–40∞C to +85∞C
–40∞C to +85∞C
Package Description
20-Lead SOIC
20-Lead SOIC
20-Lead SOIC
20-Lead SOIC
Evaluation Board
�JA
Package Option
1
58∞C/W
58∞C/W1
58∞C/W1
58∞C/W1
R-20
R-20
R-20
R-20
Thermal Resistance measured on SEMI standard 4-layer board.
Z = Pb-free part.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8321 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
PIN FUNCTION DESCRIPTIONS
Pin
Function
Description
1
SDATA
Serial Data Input. This digital input allows for an 8-bit serial (gain) word to be loaded into the internal
register with the MSB (most significant bit) first.
2
CLK
Clock Input. The clock port controls the serial attenuator data transfer rate to the 8-bit master-slave
register. A Logic 0-to-1 transition latches the data bit and a 1-to-0 transfers the data bit to the slave.
This requires the input serial data word to be valid at or before this clock transition.
3
DATEN
Data Enable Low Input. This port controls the 8-bit parallel data latch and shift register. A Logic 0-to­
1 transition transfers the latched data to the attenuator core (updates the gain) and simultaneously
inhibits serial data transfer into the register. A 1-to-0 transition inhibits the data latch (holds the previ­
ous gain state) and simultaneously enables the register for serial data load.
4, 11, 12,
13, 15, 16
GND
Common External Ground Reference.
5
BYP1
VCC/2 Reference Pin. A dc output reference level that is equal to 1/2 of the supply voltage (VCC). This
port should be externally ac-decoupled (0.1 mF capacitor). For external use of this reference voltage,
buffering is required.
6
PD
Power-Down Low Logic Input. A Logic 0 powers down (shuts off) the power amplifier disabling the
output signal and enabling the reverse amplifier. A Logic 1 enables the output power amplifier and
disables the reverse amplifier.
7, 8, 9, 17, 20
VCC
Common Positive External Supply Voltage.
10
VOUT
Output Signal Port. DC-biased to approximately VCC/2.
14
BYP2
Internal Bypass. This pin must be externally ac-decoupled (0.1 mF capacitor).
18
VIN+
Noninverting Input. DC-biased to approximately VCC/2. For single-ended inverting operation, use
0.1 mF decoupling capacitor between VIN+ and ground.
19
VIN–
Inverting Input. DC-biased to approximately VCC/2. Should be ac-coupled with a 0.1 mF capacitor.
–4–
REV. A
Typical Performance Characteristics–AD8321
70
30
20
0.3
f = 10MHz
PD =1
71D
60
OUTPUT NOISE – nV/ Hz
0.6
10
0
GAIN – dB
f = 42MHz
–0.3
0
46D
–10
23D
–0.6
–20
f = 65MHz
–0.9
0
8
16 24 32 40 48 56
GAIN CONTROL – Decimal
64
Figure 4. Gain Error vs. Gain Control
10
1
60
–47
fO = 65MHz
VIN = 0.137V p-p
(PIN = –15dBm)
(POUT = 11dBm @
MAX GAIN)
–40
DISTORTION – dBc
MAX GAIN
(71D)
50
MIN GAIN
(00D)
10
1
10
FREQUENCY – MHz
–80
100
Figure 7. Output Referred Noise vs.
Frequency
0
8
16 24 32 40 48 56
GAIN CONTROL – Decimal
64
72
0
PIN = –14dBm
(POUT = 12dBm @
MAX GAIN)
–53
PIN = –15dBm
(POUT = 11dBm @
MAX GAIN)
–20
–40
–56
–60
PIN = –17dBm
(POUT = 9dBm @
MAX GAIN)
–59
5
15
25
35
45
55
FUNDAMENTAL FREQUENCY – MHz
5
15
25
35
45
55
FUNDAMENTAL FREQUENCY – MHz
65
Figure 9. Second Order Harmonic
Distortion vs. Frequency for Various
Input Levels
POUT = 11dBm
MAX GAIN
29
28
27
26
25
24
23
65
Figure 10. Third Order Harmonic
Distortion vs. Frequency for Various
Input Levels
REV. A
PIN = –15dBm
(POUT = 11dBm @
MAX GAIN)
30
POUT = 11dBm
MAX GAIN
POUT – dBm
DISTORTION – dBc
–50
PIN = –14dBm
(POUT = 12dBm @
MAX GAIN)
PIN = –13dBm
(POUT = 13dBm @
MAX GAIN)
–59
20
PIN = –13dBm
(POUT = 13dBm @
MAX GAIN)
72
PIN = –17dBm
(POUT = 9dBm @
MAX GAIN)
Figure 8. Harmonic Distortion vs.
Gain Control
–47
64
–56
HD2
–70
20
16 24 32 40 48 56
GAIN CONTROL – Decimal
–53
HD3
–60
30
8
–50
–50
40
0
Figure 6. Output Referred Noise vs.
Gain Control
–30
PD = 1
OUTPUT NOISE – nV/ Hz
1000
10
100
FREQUENCY – MHz
Figure 5. AC Response
70
30
00D
–40
0.1
72
40
DISTORTION – dBc
–1.2
50
20
–30
3RD ORDER INTERCEPT – dBm
GAIN ERROR – dB
f = 10MHz
–80
41.0
41.4
41.8
42.2
42.6
FREQUENCY – MHz
43.0
Figure 11. Two-Tone Intermodulation Distortion
–5–
22
5
15
35
45
25
FREQUENCY – MHz
55
65
Figure 12. Third Order Intercept vs.
Frequency
AD8321
34
5mV
30
15mV
MIN GAIN
VIN = 0V p-p
MAX GAIN
POUT = 11dBm
VOUT
CL = 10pF
MAX GAIN
VIN = 0V p-p
VOUT
GAIN – dB
CL = 0pF
26
CL = 20pF
22
CL = 50pF
PD
PD
18
5V
75ns
5V
75ns
14
1
10
FREQUENCY – MHz
100
Figure 13. AC Response for Various
Capacitor Loads
Figure 14. Power Up/Power Down
Glitch
Figure 15. Power Up/Power Down
Glitch
0
7.5mV
0.75V
PD = 0
MAX GAIN
VIN = 0V p-p – 0.137V p-p
VIN = 0V p-p
MAX GAIN
tr(CLK) = 3ns
CLK
FEEDTHROUGH – dB
–20
VOUT
VOUT
MAX GAIN
–40
–60
VIN
–80
DATEN
5V
150ns
Figure 16. Clock Feedthrough
1.5V
MIN GAIN
–100
0.1
200mV
1
10
100
FREQUENCY – MHz
30ns
1000
Figure 17. Input Signal Feedthrough
vs. Frequency
Figure 18. Output Settling Time Due
to Input Change
90
100
85
90
MAX GAIN
PD =1
80
80
PD = 0
+ICC – mA
IMPEDANCE – �
VOUT
75
PD = 1
70
70
60
65
50
PD = 0
VIN
0.5V
30ns
60
1
Figure 19. Overload Recovery
10
FREQUENCY – MHz
100
Figure 20. Output Impedance vs.
Frequency
–6–
40
–50
–25
50
0
25
TEMPERATURE – �C
75
100
Figure 21. Supply Current vs.
Temperature
REV. A
AD8321
OPERATIONAL DESCRIPTION
The gain transfer function is as follows:
The AD8321 is a digitally controlled variable gain power ampli­
fier that is optimized for driving a 75 W cable. As a multifunc­
tional bipolar device on a single silicon die, it incorporates all the
analog features necessary to accommodate reverse path (upstream)
high speed (5 MHz to 65 MHz) cable data modem requirements.
The AD8321 has an overall gain range of approximately 53 dB
and is capable of greater than 100 MHz operation at output
signal levels exceeding 12 dBm. Overall, when considering
the device’s wide gain range, low distortion, wide bandwidth
and variable load drive, the device can be used in many variable
gain block applications.
AV = 26 dB – ((71 – CODE) ¥ 0.7526 dB) for CODE £ 71
AV = 26 dB for 71 £ CODE £ 127
AV = 26 dB + ((199 – CODE) ¥ 0.7526 dB) for 128 £
CODE £ 199
AV = 26 dB for 199 £ CODE £ 255
where CODE is the decimal equivalent of the 8-bit word loaded in
the AD8321’s data latch (see Figure 23).
30
20
VCC
GND
AD8321
VOUT
VIN+
INV
VIN–
GAIN – dB
10
PWR
AMP
ATTENUATOR CORE
REVERSE
AMP
0
–10
–20
DATA LATCH
DATA SHIFT REGISTER
DATA SHIFT REGISTER
POWERDOWN/
SWITCH
INTER
–30
PD
0
32
64
96
128
160
GAIN CODE – Decimal
192
224
256
Figure 23. Linear-In dB Gain vs. Gain Control
DATEN CLK
The AD8321 is composed of four analog functions in the
power-up or forward mode. The input amplifier (preamp) which
can be used single-endedly or differentially and provides a maxi­
mum of 12 dB of attenuation. If the input is used in the differ­
ential configuration, it is imperative that the input signals are
180 degrees out of phase and of equal amplitudes. This will
ensure the proper gain accuracy and harmonic performance.
SDATA
Figure 22. Functional Block Diagram
The digitally programmable gain is controlled by the three-wire
“SPI” compatible inputs. These inputs are called SDATA
(serial data input port), DATEN (data enable low input port)
and CLK (clock input port). See Pin Function Descriptions
and Functional Block diagram. The AD8321 is programmed by
an 8-bit “attenuator” word. When a standard 8-bit word is
used, the first data bit MSB will be shifted out of the 7-bit shift
register during the eighth rising CLK edge. The lower seven
bits will then be loaded into the AD8321’s digital decode sec­
tion when the DATEN input is taken high.
The preamp stage drives a vernier stage that provides the fine
tune gain adjustment. The 0.7526 dB step resolution is imple­
mented in this stage. After the vernier stage, a DAC provides the
bulk of the AD8321’s attenuation (six bits or 36 dB). The signals
in the preamp and vernier gain blocks are differential to improve
the PSRR and linearity. A single-ended current is fed from the
DAC into the output stage, which amplifies this current to the
appropriate level necessary to drive a 75 W load. The output
stage utilizes negative feedback to implement a 75 W output
impedance. This eliminates the need for an external 75 W match­
ing resistor needed in typical video (or video filter) termination
requirements.
The gain of the AD8321 is linear in steps of 0.7526 dB. The
gain transfer function starts at –27.43 dB (at decimal code 0)
and increases 0.7526 dB/LSB. The gain increases up to decimal
code 71. At this point the gain is at its maximum level of 26 dB.
If a decimal word between 71 and 127 is entered, the gain is no
longer incremented and stays at 26 dB. Since the MSB of an 8-bit
word is a “don’t care” bit, at decimal code 128, the AD8321’s
gain returns to its minimum value. The gain vs. gain control
relationship repeats itself as shown in Figure 23 for the upper
127 codes.
REV. A
–7–
AD8321
The attenuation setting in the AD8321 is determined by the
8-bit word in the data latch. The SDATA load sequence is
initiated by a falling edge on DATEN. The gain control data
(SDATA) is serially loaded (MSB first) into the 7-bit shift register
at each rising edge of the clock. See Figure 24. While DATEN
is low, the data latch holds the previous data word allowing the
attenuation level to remain unchanged. After eight clock cycles
the new data word is fully loaded and DATEN is switched high.
This enables the data latch and the loaded register data is passed to
the attenuator with the updated gain value. Also at this DATEN
transition, the internal clock is disabled, thus inhibiting new
serial input data.
APPLICATIONS
General Application
The AD8321 is primarily intended for use as the return path
(also called upstream path) Power Amplifier (PA) or line driver
in cable modem applications. Upstream data is modulated in
either QPSK or QAM format. This is done either in DSP or by
a dedicated QPSK/QAM modulator such as the AD9853 or
other modem/modulator chip. The amplifier receives its input
signal either from the dedicated QPSK/QAM modulator or from
a DAC. In both cases, the signal must be low-pass filtered
before being applied to the line driving amplifier. Because the
distance to the central office varies from cable modem sub­
scriber to subscriber, resulting in various line losses, signals from
various subscribers will require attenuation while others may
require gain. As a result, the AD8321 line driver is required to
vary its output applying attenuation or gain as needed so that all
signals arriving at the central office are of the same amplitude.
The power amplifier has two basic modes of operation. A for­
ward mode (or power-up mode) and a reverse mode (or powerdown) mode. In the power-up mode (PD = 1), the power
amplifier stage is enabled and the AD8321 has a maximum gain
of 20 V/V or 26 dB (into 75 W). With a total attenuation of
53.43 dB in the DAC, vernier and preamp, the AD8321’s total
gain range is 26 dB to –27.43 dB. In both the forward or reverse
mode the single-ended output signal maintains a dc level of
VCC/2. This dc output level provides for optimum large signal
linearity.
DOCSIS (Data Over Cable Service Interface Specifications)
requires a cable modem output signal ranging in power from a
minimum of 8 dBmV to a maximum of 58 dBmV. In cable
modem applications where DOCSIS compliance is desired, the
AD8321 amplifier must be used in conjunction with a 75 W
matching attenuator connected between the AD8321 output
and the low-pass input port of the diplexer. See the schematic in
Figure 28. The matching attenuator is used to achieve DOCSIScompliant noise levels at the lower end of the AD8321 output
power range. The insertion loss of a diplexer is typically less
than 1 dB. As a result of these combined losses, the PA line
driver must be capable of delivering sufficient power into a 75 W
load while maintaining reasonable distortion performance at the
output of the modem. (See sections containing “DOCSIS” for
further information. All references to DOCSIS pertain to
SP-RFI-I04-980724 entitled Radio Frequency Interface
Specification.)
In the power-down mode (PD = 0), the power amplifier is
turned off and a “reverse” amplifier (the inner triangle in Figure
22) is enabled. During this 1-to-0 transition, the output power
is disabled. This assures that S11 and S22 remain approximately
equal to zero thus minimizing line reflections. In the time domain,
as PD switches states, a transitional glitch and pedestal offset
results (See Figures 14 and 15). These anomalies have been
minimized by temperature compensated internal circuitry and
laser trimming. The powered down supply current drops to 52 mA
versus 90 mA in the power-up mode.
TDS
SDATA
VALID DATA WORD G1
MSB. . . .LSB
TC
VALID DATA WORD G2
TWH
CLK
TES
DATEN
TEH
8 CLOCK CYCLES
GAIN TRANSFER (G1)
GAIN TRANSFER (G2)
TOFF
PD
TGS
TON
ANALOG
OUTPUT
SIGNAL AMPLITUDE (p-p)
PEDESTAL
Figure 24. Serial Interface Timing
–8–
REV. A
AD8321
Basic Connection
Input Bias, Impedance and Termination
Figure 25 shows the basic schematic for operating the AD8321
in single-ended inverting mode. To operate in inverting mode,
connect the input signal through an ac coupling capacitor to
VIN–; VIN+ should be decoupled to ground with a 0.1 mF
capacitor. Because the amplifier operates from a single supply,
and the differential input pins are biased to approximately
VCC/2, the differential inputs must be ac-coupled using 0.1 mF
capacitors. For operation in the noninverting mode, the VIN–
pin should be decoupled to ground via a 0.1 mF capacitor, with
the input signal being fed to the AD8321 through the (ac-coupled)
VIN+ pin. Inverting mode should be chosen if the AD8321 is
being used as a drop-in replacement for the AD8320 (the
AD8321 predecessor). Balanced differential inputs to the
AD8321 may also be applied at an amplitude that is one-half
the specified single-ended input amplitude. See the Differential
Inputs section for more on this mode of operation.
On the input side, the VIN+ and VIN– have a dc bias level
equal to (VCC/2) – 0.2 V. The input signal must therefore be
ac-coupled before being applied to either input pin. The input
impedance, when operated in single-ended mode is roughly
820 W (900 W in differential mode). An external shunt resis­
tance (R1) to ground of 82.5 W is required to create a singleended input impedance of close to 75 W. If single-ended 50 W
termination is required, a 53.6 W shunt resistor may be used.
Differential input operation may be achieved by using a shunt
resistor of 41 W to ground on each of the inputs, or 82.6 W
across the inputs resulting in a differential input impedance of
approximately 75 W. Note: to avoid dc loading of either the
VIN+ or VIN– pin, the ac-coupling capacitor must be placed
between the input pin(s) and the shunt resistor(s). Refer to the
Differential Inputs section for more details on this mode of
operation.
Power Supply and Decoupling
Output Bias, Impedance and Termination
The AD8321 should be powered with a good quality (i.e., low
noise) single supply of 9 V. Although the AD8321 circuit will
function at voltages lower than 9 V, optimum performance will
not be achieved at lower supply settings. Careful attention must
be paid to decoupling the power supply pins. A 10 mF capacitor
located in near proximity to the AD8321 is required to provide
good decoupling for lower frequency signals. In addition, and
more importantly, five 0.1 mF decoupling capacitors should be
located close to each of the five power supply pins (7, 8, 9, 17,
and 20). A 0.1 mF capacitor must also be connected to the pins
labeled BYP1 and BYP2 (Pins 5 and 14) to provide decoupling
to internal nodes of the device. All six ground pins should be
connected to a common low impedance ground plane.
On the output side, the VOUT pin is also dc-biased to VCC/2 or
midway between the supply voltage and ground. The output
signal must therefore be ac-coupled before being applied to the
load. The dc-bias voltage is available on the BYP1 and BYP2
pins (Pins 5 and 14 respectively) and can be used in dc-biasing
schemes. These nodes must be decoupled to ground using a
0.1 mF capacitor as shown in Figure 25. If the BYP1 and/or
BYP2 voltages are used externally, they should be buffered.
External back termination resistors are not required when using
the AD8321. The output impedance of the AD8321 is 75 W and
is maintained dynamically. This on chip back termination is
maintained regardless of whether the amplifier is in forward
transmit mode or reverse powered down mode. If the output
signal is being evaluated on 50 W test equipment such as a
spectrum analyzer, a 75 W to 50 W adapter (commonly called
a minimum loss pad) should be used to maintain a properly
matched circuit.
VCC
+9V
C7
0.1�F
C6
10�F
C2
0.1�F
C1
0.1�F
INPUT
C8
0.1�F
VCC
C9
0.1�F
VCC
VIN+
C10
0.1�F
VCC
C11
0.1�F
VCC
VCC
C4
C5
0.1�F 0.1�F
BYP1 BYP2
VOUT
AD8321
Ce
0.1�F
TO
DIPLEXER
RIN = 75�
ATTENUATOR
CORE
VIN–
R1
82.5�
DATA LATCH
POWER­
DOWN/
SWITCH
INTER
DATA SHIFT
REGISTER
CLK
SDATA
GND GND GND GND GND
DATEN
DATEN
CLK
SDATA
PD
Figure 25. Basic Connection for Single-Ended Inverting Operation
REV. A
–9–
AD8321
Varying the Gain and SPI Programming
The gain of the AD8321 can be varied over a range of 53 dB from
approximately –27 dB to +26 dB, in increments of approximately
0.7526 dB per LSB. Programming the gain of the AD8321 is
accomplished using conventional Serial Peripheral Interface or
SPI protocol. Three digital lines, DATEN, CLK and SDATA,
are used to stream eight bits of data into the serial shift register
of the AD8321. Changing the state of the DATEN port from
Logic 1-to-0 starts the load sequence by activating the CLK
line. No changes in output signal are realized during this transi­
tion. Subsequently, any data applied to SDATA is clocked into
the serial shift register Most Significant Bit (MSB) first and on
the rising edge of each CLK pulse. The AD8321 may be pro­
grammed to deliver maximum gain (+26 dB) at decimal code
71. As a result, only the last seven bits of a typical 8-bit SPI
word effect the gain resulting in the gain response depicted in
Figure 22. Since the SPI codes from 0 through 71 appear digi­
tally identical to codes 128 through 199 for all bits except the
MSB, the AD8321 repeats the gain vs. decimal code response
twice in the 256 available codes (see Operational Description for
gain equations and Figure 23 for Gain Response). The MSB of
a typical SPI word (i.e., the first data bit presented to the SDATA
line after the DATEN transition from Logic 1 to 0 and prior to
the rising edge of the first clock pulse) is disregarded or ignored.
Data enters the serial shift register through the SDATA port
on the rising edge of the next seven CLK pulses. Returning the
DATEN line to Logic 1 latches the content of the shift register
into the attenuator core resulting in a well controlled change in
output signal level. The timing diagram for AD8321’s serial
interface is shown in Figure 24.
Gain Dependence on Load Impedance
The AD8321 has a dynamic output impedance of 75 W. This
dynamic output impedance is trimmed to provide a maximum
gain of +26 dB when loaded with 75 W. Operating the AD8321
at load impedances other than 75 W will only change the gain of
the AD8321 while the specified gain range of 53 dB is unchanged.
Varying the load impedance will result in 6 dB of additional gain
when RLOAD approaches infinity. The relationship between
RLOAD and gain is depicted in Figure 26 and is described by the
following equation:
Gain (dB) = [20 log ((2 ¥ RLOAD)/(RLOAD +75))]+(26–(0.7526 ¥
(71-Code)))
35
30
GAIN – dB
25
20
Between Burst On/Off Transients, Asynchronous PowerDown and DOCSIS
A 42% reduction in consumed power may be achieved asynchro­
nously by applying Logic 0 to PD Pin 6 activating the on-chip
“reverse amplifier.” The supply current is then reduced to
approximately 52 mA and the modem can no longer transmit in
the upstream direction. The on-chip reverse amplifier is designed
to reduce “between burst noise” and maintain a 75 W source
impedance to the low pass port of the modem’s diplexer while
minimizing power consumption. Changing the logic level applied
to the PD pin will result in a Burst On/Off Transient at the
output of the AD8321. The transient results from switching
between the forward transmit amplifier and the powered down
(reverse) amplifier. Although the resulting transient meets the
DOCSIS transient amplitude requirements at maximum gain, it
is the lower gain range (i.e., 8 dBmV to 31 dBmV) where the
AD8321 may exceed the 7 mV maximum. The diplexer may
further reduce the glitch amplitude. An external RF switch, such
as Alpha Industries AS128-73 GaAs 2 Watt High Linearity
SPDT RF switch, may be used to further reduce the spurious
emissions, improve the isolation between the cable plant and the
upstream line driver and switch in a 75 W back termination
required to maintain proper line termination to the LP port of
the diplexer (see Figure 28).
Noise and DOCSIS
One of the most difficult issues facing designers of DOCSIS
compliant modems is maintaining a quiet output from the PA
during times when no information is being transmitted upstream.
In addition, maintaining proper signal-to-noise ratios serves to
ensure the quality of transmitted data. This is extremely critical
when the output signal of the modem is set to the minimum
DOCSIS specified output level or 8 dBmV. The AD8321 output
noise spectral density at minimum gain (or 8 dBmV) is 20 nV/÷Hz
measured at 10 MHz. Considering the “Spurious Emissions
in 5 MHz to 42 MHz” of Table 4–8 in DOCSIS, the calculated
noise power in dBmV for 160 KSYM/SEC is:
Ê
Ê
ˆˆ
2
Á 20 log Á Ê 20 nV / Hz ˆ ¥ 160E + 3 ˜ ˜ + 60 or - 41.5 dBmV
¯
Á Ë
˜˜
Á
¯¯
Ë
Ë
Comparing the computed noise power to the signal at 8 dBmV
yields –49.5 dBc or 3.5 dB higher than the required –53 dBc in
DOCSIS Table 4–8. An attenuator designed to match the
AD8321 75 W source to the 75 W load may be required. Refer­
ring to the schematic of Figure 28 and the evaluation board
silkscreen of Figure 31, the matching attenuator is comprised of
the three resistors referred to as Rc, Rd and Re. Select the at­
tenuation level from Table I such that noise floor is reduced to
levels specified in DOCSIS.
15
Table I.
10
5
0
0
100
200
300
400
RLOAD – �
500
Rc (�)
Rd (�)
Re (�)
Attenuation (dB)
1304
654.3
432
331.5
8.65
17.42
26.1
35.75
1304
654.3
432
331.5
–1
–2
–3
–4
Figure 26. Maximum Gain vs. RLOAD
–10–
REV. A
AD8321
Distortion and DOCSIS
Overshoot on PC Printer Ports
Care must be taken when selecting attenuation levels specified
in Table I as the output signal from the AD8321 must compen­
sate for the losses resulting from any added attenuation as well
as the insertion losses associated with the diplexer. An increase
in input signal becomes apparent at the upper end of the gain
range and will be needed to achieve the 58 dBmV at the modem
output. The insertion losses of the diplexer may vary, depend­
ing on the quality of the diplexer and whether the frequency of
operation is in near proximity to the cut-off frequency of the
low-pass filter. Figures 9 and 10 show the expected second
and third harmonic distortion performance vs. fundamental
frequency at various input power levels. These graphs indicate
the worst harmonic levels exhibited over the entire output range
of the AD8321 (i.e., –27 dB to +26 dB). Figures 9 and 10 are
useful when it is necessary to determine inband harmonic levels
(5 MHz to 42 MHz or 5 MHz to 65 MHz). Harmonics that
are higher in frequency, as compared to the cutoff frequency of
the low-pass filter of the diplexer, will be further suppressed by
the stop band attenuation level of the LP filter in the diplexer.
Designers must balance the need to improve noise performance
by adding attenuation with the resulting need for increased
signal amplitude while maintaining DOCSIS specified dis­
tortion performance.
The data lines on some PC parallel printer ports have excessive
overshoot. Overshoot presented to the CLK pin (TP7 on the
evaluation board) may cause communications problems. The
evaluation board layout was designed to accommodate a series
resistor and shunt capacitor (R6 and C12) if required to filter or
condition the CLK data.
Evaluation Board Features and Operation
The AD8321 evaluation board (p/n AD8321-EVAL) and com­
panion software program written in Microsoft Visual Basic are
available through Analog Devices, Inc. and can be used to
control the AD8321 Variable Gain Upstream Power Amplifier
via the parallel port of a PC. This evaluation package provides a
convenient way to program the gain/attenuation of the AD8321
without the addition of any external glue logic. AD8321-EVAL
has been developed to facilitate the use of the AD8321 in an
application targeted at DOCSIS compliance. A low cost Alpha
Industries AS128-73 GaAs 2 Watt High Linearity SPDT RF
switch (referred to as SWb) is included on the evaluation board
(see Figure 28) along with accommodations for a user specified
75 W matching attenuator (See Table I for a table of resistor
values of attenuators ranging from –1 dB to –4 dB). The
AD8321 DATEN, CLK and SDATA digital lines are pro­
grammed according to the gain setting and mode of operation
selected using the Windows® interface of the control software
(see Figure 30). The serial interface of the AD8321 is ad­
dressed through the parallel port of a PC using four or more
bits (plus ground). Two additional bits from the parallel port
are used to control the RF switch(s). This software programs
the AD8321 gain or attenuation, incorporates asynchronous
control of the power-down feature (PD Pin 6) as well as asyn­
chronous control of the Alpha Industries RF switch(es) AS128­
73.* A standard printer cable is used to feed the necessary data
to the AD8321-EVAL board. These features allow the designer
to fully develop and evaluate the upstream signal path begin­
ning at the input to the PA.
Between Burst Transient Reduction
In order to reduce the amplitude of the “Burst On/Off Tran­
sient” glitch at the output of the AD8321, when switching from
forward transmit mode to reverse powered down mode, position
the SWb switch in Figure 28 to position “a” before changing the
logic applied to PD Pin 6 of the AD8321 from Logic 1-to-0
(and also 0-to-1). Use the “Enable Output Switch” feature in
the evaluation board control software (see Figure 31) to select
the appropriate position of the AS128-73 switch. A check in this
box enables the switch to pass upstream data to the output of the
evaluation board. The AS128-73 produces a glitch of approxi­
mately 5 mV p-p regardless of the AD8321 gain setting. The
AD8321-EVAL board comes with resistors and capacitors
installed on the logic lines controlling the RF switch (R8, R9,
C16, C17). These values were selected to reduce the glitch
amplitude to DOCSIS acceptable levels and may be modified
if required. The SPDT function of the AS128-73 RF switch
accommodates the need to maintain proper termination when
the diplexer is disconnected from the output of the AD8321.
The AD8321-EVAL board accommodates the needed back
termination (refer to the Cb and Rb of the evaluation circuit).
Differential Inputs
When evaluating the AD8321 in differential input mode, termi­
nation resistor(s) should be selected and applied such that the
combined resistance of the termination resistor(s) and the input
impedance of the AD8321 results in a match between the signal
source impedance and the input impedance of the AD8321. The
evaluation board is designed to accommodate Mini-Circuits T1­
6T-KK81 1:1 transformer for the purposes of converting a
single-ended (i.e., ground referenced) input signal to differen­
tial inputs. The following paragraphs identify three options for
providing differential input signals to the AD8321 evaluation
board. Option 1 uses a transformer to produce a truly differen­
tial input signal. The termination resistor(s) specified in Option
1 and 2 may also be used without the transformer if a differen­
tial signal source is available. Option 2 uses a transformer andproduces ground referenced input signals that are separated in
phase by 180∞. Option 3 relies on differential signals provided
by the user and does not employ a transformer for single-to­
differential conversion.
Differential Input Option 1: Install the Mini-Circuits T1-6T­
KK81 1:1 transformer in the T1 location of the evaluation
board. Jumpers J1, J2 and J3 should be applied pointing in the
direction of the transformer. A differential input termination
resistor of 82.5 W can be used in the R3 position. This value
should be used when the single-ended input signal has a source
impedance of 75 W. In this configuration, the input signal must
be applied to the VIN+/DIFF IN port of the evaluation board.
An open circuit is required in R1, R2 and J4 positions resulting
in a 75 W differential input termination to the AD8321. If a
50 W single-ended input source is applied to the VIN+/DIFF IN
port, the R3 value should be 53.6 W.
Windows is a registered trademark of Microsoft Corporation.
*Alpha Industries @ www.alphaind.com
REV. A
–11–
AD8321
Differential Input Option 2: Install the Mini-Circuits T1-6T­
KK81 1:1 transformer in the T1 location of the evaluation
board. Jumpers J1, J2 and J3 should be applied pointing in the
direction of the transformer. Apply an open circuit in the R3
position while J4 is applied connecting the center-tap of the
secondary to ground. A 41 W resistor should be used between
each input and ground at R1 and R2. This option will also
result in a 75 W differential input termination to the AD8321.
If a 50 W single-ended input source is applied to the VIN+/
DIFF IN port, the R1 and R2 values should be 26.7 W.
Differential Input Option 3: A differential input may be
applied to both VIN– and VIN+ inputs of the evaluation board.
In this example, no transformer is employed. Jumpers J1, J2 and
J3 are installed in line with the input signals. Select the differen­
tial input termination configuration of either Option 1 or Option 2.
Apply Option 1 resistor value to R3 for a true differential input
or apply Option 2 values to R1 and R2 to produce ground refer­
enced inputs that are separated in phase by 180∞. If the differen­
tial input signal source impedance is anything other than 75 W
or 50 W, calculate the appropriate value according to the equa­
tions below:
For Option 1 Configurations:
Desired Input Impedance = R3�900
For Option 2 and 3 (R1 = R2 = R):
Desired Input Impedance = 2 ¥ (R�450)
DIFF IN
R3
T1
AD8321
OPTION 1 DIFFERENTIAL INPUT TERMINATION
R2
DIFF IN
AD8321
T1
R1
OPTION 2 DIFFERENTIAL INPUT TERMINATION
Controlling the Evaluation Board from a PC
The AD8321-EVAL package comes with the circuit described
by Figure 28 and includes a –2 dB attenuator (reference Rc, Rd
and Re) and the control software allowing the user to program
the gain/attenuation of the AD8321 via a standard printer cable
connected to the parallel port of a PC.
Install Software
To install the “CABDRIVE” software that controls the AD8321­
EVAL evaluation circuit, close all Windows applications and
select the “SETUP” file located on Disk 1 of the AD8321­
EVAL software. Follow the on screen instructions (see Figure
29) and insert Disk 2 when prompted to do so. Enter the path
of the directory into which the control software will be installed.
Select the button in the upper left corner to begin the installa­
tion of “CABDRIVE” software into the specified directory.
Running the Software
To invoke the control software, select the “AD8321” icon from
the directory containing the installed software. After invoking
the control software, choose the appropriate printer port from
the display portrayed in Figure 30.
Controlling the Gain/Attenuation of AD8321
The AD8321 control panel has four different functions. The
slide bar controls the gain/attenuation of the AD8321. Adjust
the slider to the gain/attenuation displayed in units of dB. The
additional displays show the selection in units of Volts (output)/
Volts (input), and the corresponding control codes in decimal,
binary and hexadecimal. (See Figure 31.)
“POWER UP” and “POWER DOWN”
The buttons marked “Power Up” and “Power Down” select the
mode of operation of the AD8321. The “Power Up” button
puts the AD8321 in forward transmit mode feeding the condi­
tioned signal to the VOUT port on the evaluation board. Con­
versely, the “Power Down” button selects the reverse mode
where the forward signal transmission is disabled and the low
noise reverse amplifier actively maintains a 75 W back termina­
tion. These features may be selected asynchronously (at any
time). (See the section on Between Burst Transient Reduction
for more specific details.)
Enable Output Switch
R2
VIN+
AD8321
VIN–
R1
OPTION 3 DIFFERENTIAL INPUT TERMINATION
Figure 27. Differential Input Termination Options
An Alpha Industries AS128-73 GaAs 2W Hi Linearity switch is
installed on a standard AD8321-EVAL circuit and is controlled
by the check box on the control panel portrayed in Figure 31.
This feature is intended to remove the output of the AD8321
from the VOUT port prior to using the “Power Up” and
“Power Down” feature described above. This application circuit
may be used to reduce any transients created between bursts to
DOCSIS compliant levels. (See the section on Between Burst
Transient Reduction for more specific details.)
–12–
REV. A
AD8321
TP1
C1
0.1�F
J3
VIN–
R1
82.5�
TP4
VCC
P1–5
P1–6
P1–2
SDATA
TP6
CLK
TP7
C10
C12
1000pF
DATEN TP8
20
2
19
3
18
4
C4
P1–3
1
R6
TP9
PD
C7
C8
VCT
C9
C14
10�F
C15
0.1�F
C2
0.1�F
C11
17
5
16
6
15
7
14
8
13
9
12
10
11
NOTE:
BYPASS CAPACITORS C4, C5, C7,
C8, C9, C10 AND C11 ARE 0.1�F.
C5
TPd
Jb
TPc
TP5
AD8321
TPa
Cc
0.1�F
Rd
Rc
GND
Cd
0.1�F
TP12
AS128-73
SWb
V1
b
Re
TP13
VCC
C10
0.1�F
P1–8
P1–7
V1
R8
1k�
V2
R9
1k�
TPe
Cb
0.1�F
C6
10�F
Vct
Rf
10k�
Ce
0.1�F
TO
DIPLEXER
V2
Rb
75�
C16
1000pF
C17
1000pF
Figure 28. AD8321-EVAL Schematic of Single-Ended Inverting Input, Upstream PA Driver Solution Using AD8321,
Matching Attenuator and Alpha Industries AS128-73 RF Switch
REV. A
–13–
AD8321
EVALUATION BOARD FEATURES AND OPERATION
Figure 29. Evaluation Board Software Installation
Figure 30. Evaluation Board Control Software
–14–
REV. A
AD8321
Figure 31. Screen Display of Windows-Based Control Software
REV. A
–15–
AD8321
Figure 32. Evaluation Board Silkscreen (Component Side)
–16–
REV. A
AD8321
Figure 33. Evaluation Board Layout (Component Side)
Figure 34. Evaluation Board Layout (Solder Side)
REV. A
–17–
AD8321
EVALUATION BOARD BILL OF MATERIALS
AD8321 Evaluation Board Rev. B SINGLE- ENDED INVERTING INPUT March 17, 1999
Qty.
2
14
3
1
3
2
1
2
1
1
1
2
1
6
2
3
1
2
2
5
2
1
4
1
1
4
4
2
2
2
2
Description
Vendor
Ref Desc.
10 mF 16 V. 1350 size tantalum chip capacitor
0.1 mF 50 V. 1206 size ceramic chip capacitor
1,000 pF 50 V. 1206 size ceramic chip capacitor
82.5 W 1% 1/8 W. 1206 size chip resistor
0 W 5% 1/8 W. 1206 size chip resistor
1.00 kW 1% 1/8 W. 1206 size chip resistor
75.0 W 1% 1/8 W. 1206 size chip resistor
649 W 1% 1/8 W. 1206 size chip resistor
10.0 kW 1% 1/8 W. 1206 size chip resistor
17.4 W 1% 1/8 W. 1206 size chip resistor
Alpha # AS 128-73 GaAs Hi Linearity switch
Pink Test Point
Blue Test Point [Vct]
Grey Test Point [Bus lines]
Yellow Test Point [INPUTS]
Orange Test Point [OUTPUTS]
Red Test Point [DUT VCC]
Black Test Point [GND]
2 pin .1 inch ctr. shunt Berg # 65474 - 001
2 pin .1 inch ctr. male Header Berg # 69157 - 102
75 W right-angle BNC Telegartner # J01003A1949
Conn. 36 pin Centronics Right Angle
5-way Metal Binding Post
AD8321 AR
AD8321 REV. B Evaluation PC board
#4 - 40 ¥ 1/4 inch ss panhead machine screw
#4 - 40 ¥ 3/4 inch long aluminum round stand-off
# 2 - 56 ¥ 3/8 inch ss panhead machine screw
# 2 steel flat washer
# 2 steel internal tooth lockwasher
# 2 ss hex. machine nut
ADS# 4-7-6
ADS# 4-5-18
ADS# 4-5-20
D -K # P 82.5 FCT-ND
ADS# 3-18- 88
ADS# 3-18-11
ADS# 3-18-145
D -K # P 649 FCT-ND
ADS# 3-18-119
D -K # P17.4 FCT-ND
Alpha # AS 128-73
ADS# 12-18-63
ADS# 12-18-62
ADS# 12-18-64
ADS# 12-18-32
ADS# 12-18-60
ADS# 12-18-43
ADS# 12-18-44
ADS# 11-2-38
ADS# 11-2-37
Comp. Mktg. Services
ADS# 12-3-50
ADS# 12-7-7
ADS# AD8321AR
E.M.C.
ADS# 30-1-1
ADS# 30-16-3
ADS# 30-1-17
ADS# 30-6-6
ADS# 30-5-2
ADS# 30-7-6
C6 & C14
C1–C5, C7–C11, Cb–e
C12, C16 & C17
R1
R2 & R6, Ca
R8 & 9
Rb
Rc & Re
Rf
Rd
SWb
TPc & TPd
TP14
TP6–TP9, TP12 & TP13
TP1 & TP2
TPa, TPb & TPe
TP4
TP5 & TP15
J3 & Jb
J3, Ja, Jb, Jc, Jd
INPUTS, OUTPUT
P1
DUT VCC, GND, Vct
D.U.T.
Evaluation PC board
(p1 hardware)
(p1 hardware)
(p1 hardware)
(p1 hardware)
Optional Components J1, J2, J4, R3, Ra, SWa, T1, +VIN+
–18–
REV. A
AD8321
OUTLINE DIMENSIONS
20-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(R-20)
Dimensions shown in millimeters and (inches)
Revision History
Location
Page
6/05—Data Sheet Changed from REV. 0 to REV. A.
Changes to ORDERING GUIDE ....................................................................................................................................................4
Updated OUTLINE DIMENSIONS.............................................................................................................................................19
REV. A
–19–
–20–
C01013–0–6/05(A)
Similar pages