AD AD841SE/883B Wideband, unity-gain stable, fast settling op amp Datasheet

a
FEATURES
AC PERFORMANCE
Unity-Gain Bandwidth: 40 MHz
Fast Settling: 110 ns to 0.01%
Slew Rate: 300 V/ms
Full Power Bandwidth: 4.7 MHz for 20 V p-p into a
500 V Load
Wideband, Unity-Gain Stable,
Fast Settling Op Amp
AD841
CONNECTION DIAGRAMS
Plastic DIP (N) Package
TO-8 (H) Package
and
Cerdip (Q) Package
DC PERFORMANCE
Input Offset Voltage: 1 mV max
Input Voltage Noise: 13 nV/√Hz typ
Open-Loop Gain: 45 V/mV into a 1 kV Load
Output Current: 50 mA min
Supply Current: 12 mA max
APPLICATIONS
High Speed Signal Conditioning
Video and Pulse Amplifiers
Data Acquisition Systems
Line Drivers
Active Filters
Available in 14-Pin Plastic DIP Hermetic Cerdip, 12-Pin
TO-8 Metal Can and 20-Pin LCC Packages
Chips and MIL-STD-883B Parts Available
LCC (E) Package
PRODUCT DESCRIPTION
The AD841 is a member of the Analog Devices family of wide
bandwidth operational amplifiers. This high speed/high precision
family includes, among others, the AD840, which is stable at a
gain of 10 or greater, and the AD842, which is stable at a gain of
two or greater and has 100 mA minimum output current drive.
These devices are fabricated using Analog Devices’ junction isolated complementary bipolar (CB) process. This process permits
a combination of dc precision and wideband ac performance
previously unobtainable in a monolithic op amp. In addition to
its 40 MHz unity-gain bandwidth product, the AD841 offers extremely fast settling characteristics, typically settling to within
0.01% of final value in 110 ns for a 10 volt step.
Unlike many high frequency amplifiers, the AD841 requires no
external compensation. It remains stable over its full operating
temperature range. It also offers a low quiescent current of
12 mA maximum, a minimum output current drive capability of
50 mA, a low input voltage noise of 13 nV/√Hz and low input
offset voltage of 1 mV maximum.
The 300 V/µs slew rate of the AD841, along with its 40 MHz
gain bandwidth, ensures excellent performance in video and
pulse amplifier applications. This amplifier is well suited for use
in high frequency signal conditioning circuits and wide bandwidth active filters. The extremely rapid settling time of the
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
AD841 makes it the preferred choice for data acquisition
applications which require 12-bit accuracy. The AD841 is
also appropriate for other applications such as high speed
DAC and ADC buffer amplifiers and other wide bandwidth
circuitry.
APPLICATION HIGHLIGHTS
1. The high slew rate and fast settling time of the AD841
make it ideal for DAC and ADC buffers, and all types
of video instrumentation circuitry.
2. The AD841 is a precision amplifier. It offers accuracy to
0.01% or better and wide bandwidth performance previously available only in hybrids.
3. The AD841’s thermally balanced layout and the speed
of the CB process allow the AD841 to settle to 0.01% in
110 ns without the long “tails” that occur with other
fast op amps.
4. Laser wafer trimming reduces the input offset voltage to
1 mV max on the K grade, thus eliminating the need for
external offset nulling in many applications. Offset null
pins are provided for additional versatility.
5. The AD841 is an enhanced replacement for the
HA2541.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD841–SPECIFICATIONS (@ +258C and 615 V dc, unless otherwise noted)
Model
Conditions
Min
2
AD841J
Typ
Max
0.8
INPUT OFFSET VOLTAGE
TMIN–TMAX
Offset Drift
Input Offset Current
0.1
TMIN–TMAX
VCM = ± 10 V
TMIN–TMAX
610
86
80
OPEN-LOOP GAIN
VO = ± 10 V
RLOAD ≥ 500 Ω
TMIN–TMAX
25
12
RLOAD ≥ 500 Ω
TMIN–TMAX
VOUT = ± 10 V
± 10
50
OUTPUT RESISTANCE
FREQUENCY RESPONSE
Unity Gain Bandwidth
Full Power Bandwidth3
Rise Time4
Overshoot4
Slew Rate4
Settling Time – 10 V Step
0.1
200
2
f = 1 kHz
10 Hz to 10 MHz
Current
3.5
8
10
0.4
0.5
AD841S1
Typ
0.5
1.0
3.3
Max
Units
2.0
5.5
mV
mV
µV/°C
8
12
0.4
0.6
µA
µA
µA
µA
35
3.5
5
6
0.2
0.3
0.1
Differential Mode
INPUT VOLTAGE NOISE
Wideband Noise
OUTPUT CHARACTERISTICS
Voltage
Min
35
3.5
TMIN–TMAX
INPUT VOLTAGE RANGE
Common Mode
Common-Mode Rejection
0.5
2.0
5.0
35
INPUT BIAS CURRENT
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
AD841K
Min Typ Max
200
2
610
103
100
12
100
15
47
610
86
80
12
109
15
47
45
45
25
20
25
12
± 10
50
200
2
kΩ
pF
12
110
V
dB
dB
15
47
nV/√Hz
µV rms
45
V/mV
V/mV
± 10
50
V
mA
Open Loop
5
5
5
Ω
VOUT = 90 mV p-p
VO = 20 V p-p
RLOAD ≥ 500 Ω
AV = –1
AV = –1
AV = –1
AV = –1
to 0.1%
to 0.01%
40
40
40
MHz
4.7
10
10
300
MHz
ns
%
V/µs
3.1
200
4.7
10
10
300
3.1
200
4.7
10
10
300
3.1
200
90
110
00
110
90
110
ns
ns
OVERDRIVE RECOVERY
–Overdrive
+Overdrive
200
700
200
700
200
700
ns
ns
DIFFERENTIAL GAIN
Differential Phase
f = 4.4 MHz
f = 4.4 MHz
0.03
0.022
0.03
0.022
0.03
0.022
%
Degree
POWER SUPPLY
Rated Performance
Operating Range
Quiescent Current
Power Supply Rejection Ratio
±5
± 15
11
TMIN–TMAX
VS = ± 5 V to ± 18 V
TMIN–TMAX
86
80
± 18
12
14
100
TEMPERATURE RANGE
Rated Performance5
0
PACKAGE OPTIONS
LCC (E-20A)
Cerdip (Q-14)
Plastic (N-14)
TO-8 (H-12)
Chips
AD841JQ
AD841JN
AD841JH
AD841J CHIPS
±5
11
90
86
+75
± 15
± 18
12
14
100
0
±5
11
86
80
+75
AD841KQ
AD841KN
AD841KH
± 15
–55
± 18
12
16
100
+125
V
V
mA
mA
dB
dB
°C
AD841SE, AD841SE/883B
AD841SQ, AD841SQ/883B
AD841SH, AD841SH/883B
AD841S CHIPS
NOTES
1
Standard Military Drawing Available: 5962-89641012A – (SE/883B); 5962-8964101CA – (SQ/883B).
2
Input offset voltage specifications are guaranteed after 5 minutes at T A = +25°C.
3
Full power bandwidth = Slew Rate/2 π VPEAK.
3
Refer to Figure 19.
4
“S” grade TMIN–TMAX specifications are tested with automatic test equipment at T A = –55°C and TA = +125°C.
All min and max specifications are guaranteed. Specifications shown in boldface are tested on all production units.
Specifications subject to change without notice.
–2–
REV. B
AD841
NOTES
1
Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions above those indicated in
the operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2
Maximum internal power dissipation is specified so that T J does not exceed
+175°C at an ambient temperature of +25°C.
Thermal Characteristics:
θJC
θJA
θSA
Cerdip Package 35°C/W 110°C/W 38°C/W Recommended Heat Sink:
TO-8 Package 30°C/W 100°C/W 37°C/W Aavid Engineering© #602B
Plastic Package 30°C/W 100°C/W
LCC Package
35°C/W 150°C/W
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Internal Power Dissipation2
TO-8 (H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 W
Plastic (N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 W
Cerdip (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 W
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± Vs
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . ± 6 V
Storage Temperature Range
Q, H, E . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +125°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +175°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
METALIZATION PHOTOGRAPH
Contact factory for latest dimensions.
Dimensions shown in inches and (mm).
REV. B
–3–
AD841–Typical Characteristics
(at +258C and VS = 615 V, unless otherwise noted)
Figure 1. Input Common-Mode
Range vs. Supply Voltage
Figure 2. Output Voltage Swing
vs. Supply Voltage
Figure 3. Output Voltage Swing
vs. Load Resistance
Figure 4. Quiescent Current vs.
Supply Voltage
Figure 5. Input Bias Current vs.
Temperature
Figure 6. Output Impedance vs.
Frequency
Figure 7. Quiescent Current vs.
Temperature
Figure 8. Short-Circuit Current
Limit vs. Temperature
Figure 9. Gain Bandwidth Product
vs. Temperature
–4–
REV. B
AD841
Figure 10. Open-Loop Gain and
Phase Margin vs. Frequency
Figure 13. Common-Mode
Rejection vs. Frequency
Figure 16. Harmonic Distortion vs.
Frequency
REV. B
Figure 11. Open-Loop Gain vs.
Supply Voltage
Figure 14. Large Signal Frequency
Response
Figure 17. Slew Rate vs.
Temperature
–5–
Figure 12. Power Supply Rejection
vs. Frequency
Figure 15. Output Swing and
Error vs. Settling Time
Figure 18. Input Voltage Noise
Spectral Density
AD841
Figure 19a. Inverting Amplifier
Configuration (DIP Pinout)
Figure 20a. Unity-Gain Buffer Amplifier
Configuration (DIP Pinout)
OFFSET NULLING
The input offset voltage of the AD841 is very low for a high
speed op amp, but if additional nulling is required, the circuit
shown in Figure 21 can be used.
Figure 19b. Inverter Large Signal
Pulse Response
Figure 20b. Buffer Large Signal
Pulse Response
Figure 19c. Inverter Small Signal
Pulse Response
Figure 20c. Buffer Small Signal
Pulse Response
INPUT CONSIDERATIONS
An input resistor (RIN in Figure 20) is recommended in circuits
where the input to the AD841 will be subjected to transient or
continuous overload voltages exceeding the ± 6 V maximum differential limit. This resistor provides protection for the input
transistors by limiting the maximum current that can be forced
into the input.
For high performance circuits it is recommended that a resistor
(RB in Figures 19 and 20) be used to reduce bias current errors
by matching the impedance at each input. The output voltage
error caused by the offset current is more than an order of magnitude less than the error present if the bias current error is not
removed.
AD841 SETTLING TIME
Figures 22 and 24 show the settling performance of the AD841
in the test circuit shown in Figure 23.
Figure 21. Offset Nulling (DIP Pinout)
Settling time is defined as:
The interval of time from the application of an ideal step
function input until the closed-loop amplifier output has
entered and remains within a specified error band.
This definition encompasses the major components which comprise settling time. They include (1) propagation delay through
the amplifier; (2) slewing time to approach the final output
value; (3) the time of recovery from the overload associated with
slewing and (4) linear settling to within the specified error band.
–6–
REV. B
Applying the AD841
Figure 24. AD841 Settling Demonstrating No Settling
Tails
Figure 22. AD841 0.01% Settling Time
Expressed in these terms, the measurement of settling time is obviously a challenge and needs to be done accurately to assure the
user that the amplifier is worth consideration for the application.
GROUNDING AND BYPASSING
In designing practical circuits with the AD841, the user must
remember that whenever high frequencies are involved, some
special precautions are in order. Circuits must be built with
short interconnect leads. Large ground planes should be used
whenever possible to provide a low resistance, low inductance
circuit path, as well as minimizing the effects of high frequency
coupling. Sockets should be avoided because the increased
interlead capacitance can degrade bandwidth.
Feedback resistors should be of low enough value to assure that
the time constant formed with the circuit capacitances will not
limit the amplifier performance. Resistor values of less than
5 kΩ are recommended. If a larger resistor must be used, a
small (<10 pF) feedback capacitor in parallel with the feedback
resistor, RF, may be used to compensate for these stray capacitances and optimize the dynamic performance of the amplifier
in the particular application.
Power supply leads should be bypassed to ground as close as
possible to the amplifier pins. A 2.2 µF capacitor in parallel
with a 0.1 µF ceramic disk capacitor is recommended.
Figure 23. Settling Time Test Circuit
Measurement of the AD841’s 0.01% settling in 110 ns was accomplished by amplifying the error signal from a false summing
junction with a very high speed proprietary hybrid error amplifier specially designed to enable testing of small settling errors.
The device under test was driving a 500 Ω load. The input to
the error amp is clamped in order to avoid possible problems associated with the overdrive recovery of the oscilloscope input
amplifier. The error amp gains the error from the false summing
junction by 10, and it contains a gain vernier to fine trim the
gain.
CAPACITIVE LOAD DRIVING ABILITY
Like all wideband amplifiers, the AD841 is sensitive to capacitive loading. The AD841 is designed to drive capacitive loads of
up to 20 pF without degradation of its rated performance. Capacitive loads of greater than 20 pF will decrease the dynamic
performance of the part although instability should not occur
unless the load exceeds 100 pF (for a unity-gain follower). A
resistor in series with the output can be used to decouple larger
capacitive loads.
Figure 24 shows the “long term” stability of the settling characteristics of the AD841 output after a 10 V step. There is no evidence of settling tails after the initial transient recovery time.
The use of a junction isolated process, together with careful layout, avoids these problems by minimizing the effects of transistor isolation capacitance discharge and thermally induced shifts
in circuit operating points. These problems do not occur even
under high output current conditions.
REV. B
Figure 25 shows a typical configuration for driving a large capacitive load. The 51 Ω output resistor effectively isolates the
high frequency feedback from the load and stabilizes the circuit.
Low frequency feedback is returned to the amplifier summing
junction via the low pass filter formed by the 51 Ω resistor and
the load capacitance, CL.
–7–
C1242–15–11/88
AD841
Figure 27. Overdrive Recovery
Figure 25. Circuit for Driving a Large Capacitive Load
USING A HEAT SINK
The AD841 draws less quiescent power than most precision
high speed amplifiers and is specified for operation without a
heat sink. However, when driving low impedance loads, the current to the load can be 4 to 5 times the quiescent current. This
will create a noticeable temperature rise. Improved performance
can be achieved by using a small heat sink such as the Aavid
Engineering #602B.
Figure 28. Overdrive Recovery Test Circuit
TERMINATED LINE DRIVER
The AD841 functions very well as a high speed line driver of either terminated or unterminated cables. Figure 26 shows the
AD841 driving a doubly terminated cable in a follower configuration. The AD841 maintains a typical slew rate of 300 V/µs,
which means it can drive a ± 10 V, 4.7 MHz signal or a ± 3 V,
15.9 MHz signal.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
14-Pin Plastic (N) Package
14-Pin Cerdip (Q) Package
The termination resistor, RT, (when equal to the characteristic
impedance of the cable) minimizes reflections from the far end
of the cable. A back-termination resistor (RBT, also equal to the
characteristic impedance of the cable) may be placed between
the AD841 output and the cable in order to damp any stray signals caused by a mismatch between RT and the cable’s characteristic impedance. This will result in a “cleaner” signal, but
since 1/2 the output voltage will be dropped across RBT, the op
amp must supply double the output signal required if there is no
back termination. Therefore the full power bandwidth is cut in
half.
12-Lead Metal Can Package
(TO-8 Style)
E-20A
20-Terminal Leadless
Ceramic Chip Carrier
Figure 26. Line Driver Configuration
OVERDRIVE RECOVERY
Figure 27 shows the overdrive recovery capability of the AD841.
Typical recovery time is 200 ns from negative overdrive and
700 ns from positive overdrive.
–8–
REV. B
PRINTED IN U.S.A.
If termination is not used, cables appear as capacitive loads. If
this capacitive load is large, it should be decoupled from the
AD841 by a resistor in series with the output (see above:
Driving a Capacitive Load).
Similar pages