AD ADG836 Cmos 1.65 v to 3.6 v dual spdt/2:1 mux Datasheet

0.5 Ω CMOS 1.65 V TO 3.6 V
Dual SPDT/2:1 MUX
ADG836
FEATURES
ADG836
0.5 Ω typical on resistance
0.8 Ω maximum on resistance at 125°C
1.65 V to 3.6 V operation
Automotive temperature range: –40°C to +125°C
High current carrying capability: 300 mA continuous
Rail-to-rail switching operation
Fast-switching times <20 ns
Typical power consumption (<0.1 µW)
S1A
D1
S1B
IN1
IN2
S2A
D2
APPLICATIONS
SWITCHES SHOWN FOR A LOGIC 1 INPUT
Cellular phones
PDAs
MP3 players
Power routing
Battery-powered systems
PCMCIA cards
Modems
Audio and video signal routing
Communication systems
04308-001
S2B
Figure 1.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADG836 is a low voltage CMOS device containing two
independently selectable single-pole, double-throw (SPDT)
switches. This device offers ultralow on resistance of less than
0.8 Ω over the full temperature range. The ADG836 is fully
specified for 3.3 V, 2.5 V, and 1.8 V supply operation.
1.
<0.8 Ω over full temperature range of –40°C to +125°C.
2.
Single 1.65 V to 3.6 V operation.
3.
Compatible with 1.8 V CMOS logic.
4.
High current handling capability (300 mA continuous
current at 3.3 V).
5.
Low THD + N (0.02% typ).
6.
3 mm × 3 mm LFCSP package and 10-lead MSOP package.
Each switch conducts equally well in both directions when on,
and has an input signal range that extends to the supplies. The
ADG836 exhibits break-before-make switching action.
The ADG836 is available in a 10-lead MSOP and a 3 mm × 3 mm
12-lead LFCSP.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
ADG836
TABLE OF CONTENTS
Specifications..................................................................................... 3
Typical Performance Characteristics ..............................................8
Absolute Maximum Ratings............................................................ 6
Test Circuits..................................................................................... 11
ESD Caution.................................................................................. 6
Outline Dimensions ....................................................................... 13
Pin Configurations ........................................................................... 7
Ordering Guide .......................................................................... 13
REVISION HISTORY
4/05—Rev. 0 to Rev. A
Updated Format..................................................................Universal
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 4
Changes to Table 3............................................................................ 5
Changes to Ordering Guide .......................................................... 13
Revision 0: Initial Version
Rev. A | Page 2 of 16
ADG836
SPECIFICATIONS
VDD = 2.7 V to 3.6 V, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match
Between Channels (∆RON)
On Resistance Flatness (RFLAT (ON))
LEAKAGE CURRENTS
Source Off Leakage IS (OFF)
+25°C
Temperature1
−40°C to +85°C −40°C to +125°C
0 V to VDD
0.5
0.65
0.04
0.75
0.8
0.075
0.08
0.15
0.16
0.1
Unit
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
±0.2
nA typ
Channel On Leakage ID, IS (ON)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
±0.2
nA typ
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS2
tON
4
tOFF
Break-Before-Make Time Delay
(tBBM)
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion (THD + N)
Insertion Loss
−3 dB Bandwidth
CS (OFF)
CD, CS (ON)
POWER REQUIREMENTS
IDD
2
VDD = 2.7 V, VS = 0 V to VDD, IS = 100 mA;
Figure 19
VDD = 2.7 V, VS = 0.65 V, IS = 100 mA
VDD = 2.7 V, VS = 0 V to VDD
IS = 100 mA
VDD = 3.6 V
VS = 0.6 V/3.3 V, VD = 3.3 V/0.6 V;
Figure 20
VS = VD = 0.6 V or 3.3 V; Figure 21
2
0.8
V min
V max
VIN = VINL or VINH
±0.1
µA typ
µA max
pF typ
40
−67
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
−90
dB typ
−67
dB typ
0.02
%
−0.05
57
25
75
dB typ
MHz typ
pF typ
pF typ
RL = 50 Ω, CL = 35 pF
VS = 1.5 V/0 V; Figure 22
RL = 50 Ω, CL = 35 pF
VS = 1.5 V; Figure 22
RL = 50 Ω, CL = 35 pF
VS1 = VS2 = 1.5 V; Figure 23
VS = 1.5 V, RS = 0 Ω, CL = 1 nF; Figure 24
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
Figure 25
S1A−S2A/S1B−S2B, RL = 50 Ω,
CL = 5 pF, f = 100 kHz; Figure 28
S1A−S1B/S2A−S2B, RL = 50 Ω,
CL = 5 pF, f = 100 kHz; Figure 27
RL = 32 Ω, f = 20 Hz to 20 kHz,
VS = 2 V p-p
RL = 50 Ω, CL = 5 pF; Figure 26
RL = 50 Ω, CL = 5 pF; Figure 26
0.003
µA typ
µA max
0.005
21
26
4
7
17
28
29
8
9
5
1
1
Test Conditions/Comments
4
Temperature range for Y version is −40°C to +125°C.
Guaranteed by design, not subject to production test.
Rev. A | Page 3 of 16
VDD = 3.6 V
Digital inputs = 0 V or 3.6 V
ADG836
VDD = 2.5 V ± 0.2 V, GND = 0 V, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (∆RON)
On Resistance Flatness (RFLAT (ON))
LEAKAGE CURRENTS
Source Off Leakage IS (OFF)
Channel On Leakage ID, IS (ON)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS2
tON
Temperature1
+25°C −40°C to +85°C −40°C to +125°C Unit
0 V to VDD
0.65
0.72
0.04
0.8
0.88
0.08
0.085
0.23
0.24
0.16
±0.2
±0.2
nA typ
nA typ
1.7
0.7
V min
V max
±0.1
µA typ
µA max
pF typ
0.005
4
23
29
tOFF
5
7
Break-before-Make Time Delay (tBBM) 17
30
31
8
9
5
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
30
−67
−90
−67
Total Harmonic Distortion (THD + N)
Insertion Loss
–3 dB Bandwidth
CS (OFF)
CD, CS (ON)
POWER REQUIREMENTS
IDD
0.022
−0.06
57
25
75
0.003
1
1
2
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
4
Temperature range for Y version is −40°C to +125°C.
Guaranteed by design, not subject to production test.
Rev. A | Page 4 of 16
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
Test Conditions/Comments
VDD = 2.3 V, VS = 0 V to VDD, IS = 100 mA;
Figure 19
VDD = 2.3 V, VS = 0.7 V, IS = 100 mA
VDD = 2.3 V, VS = 0 V to VDD, IS = 100 mA
VDD = 2.7 V
VS = 0.6 V/2.4 V, VD = 2.4 V/0.6 V; Figure 20
VS = VD = 0.6 V or 2.4 V; Figure 21
VIN = VINL or VINH
RL = 50 Ω, CL = 35 pF
VS = 1.5 V/0 V; Figure 22
RL = 50 Ω, CL = 35 pF
VS = 1.5 V; Figure 22
RL = 50 Ω, CL = 35 pF
VS1 = VS2 = 1.5 V; Figure 23
VS = 1.25 V, RS = 0 Ω, CL = 1 nF; Figure 24
RL = 50 Ω, CL = 5 pF, f = 100 kHz; Figure 25
S1A−S2A/S1B−S2B,
RL = 50 Ω, CL = 5 pF, f = 100 kHz; Figure 28
dB typ
S1A−S1B/S2A−S2B,
RL = 50 Ω, CL = 5 pF, f = 100 kHz; Figure 27
%
RL = 32 Ω, f = 20 Hz to 20 kHz, VS = 1.5 V p-p
dB typ
RL = 50 Ω, CL = 5 pF; Figure 26
MHz typ RL = 50 Ω, CL = 5 pF; Figure 26
pF typ
pF typ
VDD = 2.7 V
µA typ
Digital inputs = 0 V or 2.7 V
µA max
ADG836
VDD = 1.65 V ± 1.95 V, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (∆RON)
LEAKAGE CURRENTS
Source Off Leakage IS (OFF)
Channel On Leakage ID, IS (ON)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS2
tON
+25°C
Temperature1
−40°C to +85°C −40°C to +125°C
0 V to VDD
1
1.4
2
2.2
4
2.2
4
0.1
Ω typ
±0.2
nA typ
±0.2
nA typ
VDD = 1.95 V
VS = 0.6 V/1.65 V, VD = 1.65 V/0.6 V;
Figure 20
VS = VD = 0.6 V or 1.65 V; Figure 21
µA typ
µA max
pF typ
VIN = VINL or VINH
±0.1
RL = 50 Ω, CL = 35 pF
VS = 1.5 V/0 V; Figure 22
RL = 50 Ω, CL = 35 pF
VS = 1.5 V; Figure 22
RL = 50 Ω, CL = 35 pF
VS1 = VS2 = 1 V; Figure 23
VS = 1 V, RS = 0 V, CL = 1 nF; Figure 24
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
Figure 25
S1A−S2A/S1B−S2B;
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
Figure 28
S1A−S1B/S2A−S2B;
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
Figure 27
RL = 32 Ω, f = 20 Hz to 20 kHz,
VS = 1.2 V p-p
RL = 50 Ω, CL = 5 pF; Figure 26
RL = 50 Ω, CL = 5 pF; Figure 26
0.005
4
Break-Before-Make Time Delay (tBBM)
Charge Injection
Off Isolation
20
−67
Channel-to-Channel Crosstalk
−90
dB typ
−67
dB typ
Total Harmonic Distortion, THD
0.14
%
Insertion Loss
–3 dB Bandwidth
−0.08
57
dB typ
MHz
typ
pF typ
pF typ
38
39
10
11
25
75
0.003
1.0
VDD = 1.8 V, VS = 0 V to VDD, IS = 100 mA;
Figure 19
VDD = 1.65 V, VS = 0 V to VDD,
IS = 100 mA; Figure 19
VDD = 1.65 V, VS = 0.7 V, IS = 100 mA
V min
V max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
CS (OFF)
CD, CS (ON)
POWER REQUIREMENTS
IDD
Test Conditions/Comments
0.65 VDD
0.35 VDD
5
2
V
Ω typ
Ω max
Ω max
28
37
7
9
21
tOFF
1
Unit
4
Temperature range for Y version is −40°C to +125°C.
Guaranteed by design, not subject to production test.
Rev. A | Page 5 of 16
µA typ
µA max
VDD = 1.95 V
Digital inputs = 0 V or 1.95 V
ADG836
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter
VDD to GND
Analog Inputs1
Digital Inputs1
Peak Current, S or D
3.3 V Operation
2.5 V Operation
1.8 V Operation
Continuous Current, S or D
3.3 V Operation
2.5 V Operation
1.8 V Operation
Operating Temperature Range
Automotive (Y Version)
Storage Temperature Range
Junction Temperature
MSOP Package
θJA Thermal Impedance
θJC Thermal Impedance
LFCSP Package
θJA Thermal Impedance (3-Layer
Board)
IR Reflow, Peak Temperature <20 sec
1
Rating
−0.3 V to +4.6 V
−0.3 V to VDD + 0.3 V
−0.3 V to 4.6 V or 10 mA,
whichever occurs first
500 mA
460 mA
420 mA (pulsed at 1ms,
10% duty cycle max)
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating may be applied at any one
time.
Table 5. Truth Table
Logic
0
1
300 mA
275 mA
250 mA
Switch A
Off
On
−40°C to +125°C
−65°C to +150°C
150°C
206°C/W
44°C/W
61.1°C/W
235°C
Overvoltages at IN, S, or D are clamped by internal diodes. Current should be
limited to the maximum ratings given.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 6 of 16
Switch B
On
Off
ADG836
IN1 1
11 N1
10 D1
12 NC
PIN CONFIGURATIONS
10 D1
ADG836
9
S1B
GND 3
TOP VIEW
(Not to Scale)
8
VDD
S1A 1
7
S2B
GND 2
ADG836
8 VDD
6
D2
S2A 3
TOP VIEW
(Not to Scale)
7 S2B
Figure 2. 10-Lead MSOP (RM-10)
04308-003
9 S1B
D2 6
NC = NO CONNECT
NC 4
IN2 5
PIN 1
INDICATOR
IN2 5
S2A 4
04308-002
S1A 2
Figure 3. 12-Lead LFCSP (CP-12)
Table 6. Terminology
VDD
IDD
GND
S
D
IN
VD (VS)
RON
RFLAT (ON)
∆RON
IS (OFF)
ID (OFF)
ID, IS (ON)
VINL
VINH
IINL (IINH)
CS (OFF)
CD (OFF)
CD, CS (ON)
CIN
tON
tOFF
tBBM
Charge Injection
Off Isolation
Crosstalk
−3 dB Bandwidth
On Response
Insertion Loss
THD + N
Most positive power supply potential.
Positive supply current.
Ground (0 V) reference.
Source terminal. May be an input or output.
Drain terminal. May be an input or output.
Logic control input.
Analog voltage on terminals D, S.
Ohmic resistance between D and S.
Flatness is defined as the difference between the maximum and minimum value of on resistance as measured over the
specified analog signal range.
On resistance match between any two channels.
Source leakage current with the switch off.
Drain leakage current with the switch off.
Channel leakage current with the switch on.
Maximum input voltage for Logic 0.
Minimum input voltage for Logic 1.
Input current of the digital input.
Off switch source capacitance. Measured with reference to ground.
Off switch drain capacitance. Measured with reference to ground.
On switch capacitance. Measured with reference to ground.
Digital input capacitance.
Delay time between the 50% and the 90% points of the digital input and switch on condition.
Delay time between the 50% and the 90% points of the digital input and switch off condition.
On or off time measured between the 80% points of both switches when switching from one to another.
A measure of the glitch impulse transferred from the digital input to the analog output during on-off switching.
A measure of unwanted signal coupling through an off switch.
A measure of unwanted signal, which is coupled through from one channel to another, as a result of parasitic
capacitance.
The frequency at which the output is attenuated by 3 dB.
The frequency response of the on switch.
The loss due to the on resistance of the switch.
The ratio of the harmonics amplitude plus noise of a signal to the fundamental.
Rev. A | Page 7 of 16
ADG836
TYPICAL PERFORMANCE CHARACTERISTICS
0.60
1.2
TA = 25°C
VDD = 3.3V
0.55
VDD = 3V
1.0
VDD = 2.7V
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
0.50
0.45
0.40
VDD = 3.3V
VDD = 3.6V
0.35
0.8
+125°C
+85°C
0.6
0.4
+25°C
0.30
–40°C
0.20
0
0.5
1.0
1.5
2.0
VD, VS (V)
2.5
3.0
04308-007
0.2
04449-0-004
0.25
0
0
3.5
1.0
1.5
2.0
2.5
3.0
VD, VS (V)
Figure 4. On Resistance vs. VD (VS) VDD = 2.7 to 3.6 V
Figure 7. On Resistance vs. VD (VS) for Different Temperature, 3.3 V
0.8
1.2
TA = 25°C
VDD = 2.5V
0.7
1.0
VDD = 2.3V
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
0.5
0.6
0.5
VDD = 2.5V
VDD = 2.7V
0.4
+125°C
0.8
+85°C
0.6
+25°C
0.4
–40°C
0.2
0
0.5
1.0
1.5
0
2.5
2.0
04308-008
0.2
04308-005
0.3
0
0.5
1.0
Figure 5. On Resistance vs. VD (VS) VDD = 2.5 V to 0.2 V
1.4
TA = 25°C
2.5
–40°C
VDD = 1.8V
1.6
2.0
Figure 8. On Resistance vs. VD (VS) for Different Temperature, 2.5 V
1.8
1.2
VDD = 1.65V
+25°C
+125°C
ON RESISTANCE (Ω)
1.4
1.2
VDD = 1.8V
1.0
0.8
0.6
1.0
0.8
0.7
+85°C
0.5
VDD = 1.95V
0.2
0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
04308-009
0.4
04308-006
ON RESISTANCE (Ω)
1.5
VD, VS (V)
VD, VS (V)
0
0
2.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
VD, VS (V)
VD, VS (V)
Figure 6. On Resistance vs. VD (VS) VDD = 1.8 ± 3.6
Figure 9. On Resistance vs. VD (VS) for Different Temperature, 1.8 V
Rev. A | Page 8 of 16
ADG836
80
90
VDD = 3.3V
ID, IS (ON)
70
40
60
20
QINJ (pC)
0
50
40
VCC = 3.3V
–20
VCC = 2.5V
30
IS (OFF)
–40
20
04308-010
–60
–80
0
20
40
60
80
100
VCC = 1.8V
04308-013
CURRENT (nA)
TA = 25°C
80
60
10
0
120
0
0.5
1.0
1.5
TEMPERATURE (°C)
2.0
2.5
3.0
3.5
VS (V)
Figure 10. Leakage Current vs. Temperature, 3.3 V
Figure 13. Charge Injection vs. Source Voltage
60
35
VDD = 2.5V
50
30
40
25
VDD = 2.5V
ID, IS (ON)
TIME (ns)
20
10
0
–10
40
60
80
100
VDD = 2.5V
VDD = 1.8V
5
04308-011
–40
20
15
tOFF
–30
0
VDD = 3V
10
IS (OFF)
–20
20
0
–40
120
04308-014
30
CURRENT (nA)
VDD = 1.8V
tON
VDD = 3V
–20
0
TEMPERATURE (°C)
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 11. Leakage Current vs. Temperature, 2.5 V
Figure 14. ton/toff Times vs. Temperature
50
1
VDD = 1.8V
0
40
–1
–2
ATTENUATION (dB)
IS, ID (ON)
20
10
0
0
20
40
60
80
100
–4
–5
TA = 25°C
VCC = 3.3V/2.5V/1.8V
–6
–7
–8
–9
–11
04308-015
–10
–20
–3
–10
IS (OFF)
04308-012
CURRENT (nA)
30
–12
–13
0.01
120
TEMPERATURE (°C)
0.1
1
10
FREQUENCY (MHz)
Figure 15. Bandwidth
Figure 12. Leakage Current vs. Temperature, 1.8 V
Rev. A | Page 9 of 16
100
1000
ADG836
0
–10
VDD = 2.5V
TA = 25°C
S1A–D1
32V LOAD
0.08
1.5V p-p
TA = 25°C
VCC = 3.3V/2.5V/1.8V
–30
THD + N (%)
ATTENUATION (dB)
–20
0.10
–40
–50
0.06
0.04
–60
04308-016
–80
0.01
0.1
1
10
100
0
20
1000
Figure 16. Off Isolation vs. Frequency
S1A–S1B
–20
ATTENUATION (dB)
TA = 25°C
VCC = 3.3V/2.5V/1.8V
–40
S1A–S2A
–50
–60
–70
04308-017
–80
–90
0.1
1
10
100
200
500
1k
2k
5k
Figure 18. Total Harmonic Distortion + Noise
–10
–100
0.01
50
FREQUENCY (Hz)
FREQUENCY (MHz)
–30
04308-018
0.02
–70
100
1000
FREQUENCY (MHz)
Figure 17. Crosstalk vs. Frequency
Rev. A | Page 10 of 16
10k
20k
ADG836
TEST CIRCUITS
IDS
ID (ON)
ID (OFF)
S
A
D
S
NC
A
D
A
RON = V1/IDS
Figure 19. On Resistance
Figure 20. Off Leakage
Figure 21. On Leakage
VDD
0.1µF
VDD
S1B
S1A
VS
VOUT
D
RL
50Ω
IN
50%
VIN
CL
35pF
50%
90%
90%
GND
tON
tOFF
04308-022
VOUT
Figure 22. Switching Times, tON, tOFF
VDD
0.1µF
50%
VDD
S1B
S1A
VS
VIN
VOUT
VOUT
D
80%
CL
35pF
RL
IN
80%
tBBM
tBBM
04308-023
50Ω
50%
0V
GND
Figure 23. Break-Before-Make Time Delay, tBBM
VDD
SW ON
S1B
NC
D
VS
SW OFF
VIN
S1A
VOUT
1nF
IN
VOUT
∆VOUT
QINJ = CL × ∆VOUT
GND
Figure 24. Charge Injection
Rev. A | Page 11 of 16
04308-024
VS
D
04308-019
S
VD
04308-020
VD
VS
04308-021
IS (OFF)
V1
ADG836
VDD
VDD
0.1µF
0.1µF
NETWORK
ANALYZER
S1B
S1A
50Ω
VS
RL
50Ω
VOUT
50Ω
OFF ISOLATION = 20 LOG
RL
50Ω
VS
04308-025
GND
D
S1B
D
RL
50Ω
VDD
S1A
VOUT
50Ω
GND
VOUT
VS
CHANNEL-TO-CHANNEL CROSSTALK = 20 LOG
VOUT
VS
Figure 27. Channel-to-Channel Crosstalk (S1A–S1B)
Figure 25. Off Isolation
VDD
0.1µF
NETWORK
ANALYZER
VOUT
NETWORK
ANALYZER
VDD
50Ω
S1B
50Ω
S1A
S2A
D2
NC
S2B
VS
RL
50Ω
GND
INSERTION LOSS = 20 LOG
VOUT
VOUT WITH SWITCH
50Ω
VS
S1A
D1
S1B
CHANNEL-TO-CHANNEL CROSSTALK = 20 LOG
NC
VOUT
VS
VOUT WITHOUT SWITCH
Figure 28. Channel-to-Channel Crosstalk (S1A–S2A)
Figure 26. Bandwidth
Rev. A | Page 12 of 16
50Ω
04308-028
D
04308-026
NC
NETWORK
ANALYZER
04308-027
VDD
ADG836
OUTLINE DIMENSIONS
3.00 BSC
10
6
4.90 BSC
3.00 BSC
1
5
PIN 1
0.50 BSC
0.95
0.85
0.75
1.10 MAX
0.15
0.00
0.27
0.17
SEATING
PLANE
0.80
0.60
0.40
8°
0°
0.23
0.08
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-BA
Figure 29. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
3.00
BSC SQ
0.60 MAX
0.45
PIN 1
INDICATOR
0.75
0.55
0.35
9
2.75
BSC SQ
TOP
VIEW
10 11 12
8
12 MAX
1.00
0.85
0.80
SEATING
PLANE
*1.45
1
1.30 SQ
1.15
2
7
6
EXPOSED PAD
(BOTTOM VIEW)
PIN 1
INDICATOR
5
4
3
0.25 MIN
0.50
BSC
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.20 REF
0.30
0.23
0.18
COPLANARITY
0.08
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-1
EXCEPT FOR EXPOSED PAD DIMENSION.
Figure 30. 12-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
3 x 3 mm Body, Very Thin Quad
(CP-12-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADG836YRM
ADG836YRM-REEL
ADG836YRM-REEL7
ADG836YRMZ2
ADG836YRMZ-REEL2
ADG836YRMZ-REEL72
ADG836YCP-REEL
ADG836YCP-REEL7
1
2
Temperature Range
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Package Description
Mini Small Outline Package (MSOP)
Mini Small Outline Package (MSOP)
Mini Small Outline Package (MSOP)
Mini Small Outline Package (MSOP)
Mini Small Outline Package (MSOP)
Mini Small Outline Package (MSOP)
Lead Frame Chip Scale Package (LFCSP_VQ)
Lead Frame Chip Scale Package (LFCSP_VQ)
Branding on this package is limited to three characters due to space constraints.
Z = Pb-free part.
Rev. A | Page 13 of 16
Package Option
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
CP-12-1
CP-12-1
Branding1
S9A
S9A
S9A
S05
S05
S05
S9A
S9A
ADG836
NOTES
Rev. A | Page 14 of 16
ADG836
NOTES
Rev. A | Page 15 of 16
ADG836
NOTES
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C04308-0-4/05(A)
Rev. A | Page 16 of 16
Similar pages