AD ADT7468 Dbcoolâ ¢ remote thermal controller and voltage monitor Datasheet

dBCool™ Remote Thermal
Controller and Voltage Monitor
ADT7468
FEATURES
GENERAL DESCRIPTION
Monitors up to 5 voltages
Controls and monitors up to 4 fans
High and low frequency fan drive signal
1 on-chip and 2 remote temperature sensors
Series resistance cancellation on the remote channel
Extended temperature measurement range, up to 191°C
Dynamic TMIN control mode optimizes system acoustics
intelligently
Automatic fan speed control mode controls system
cooling based on measured temperature
Enhanced acoustic mode dramatically reduces user
perception of changing fan speeds
Thermal protection feature via THERM output
Monitors performance impact of Intel® Pentium™ 4
processor
Thermal control circuit via THERM input
2-wire, 3-wire, and 4-wire fan speed measurement
Limit comparison of all monitored values
Meets SMBus 2.0 electrical specifications
(fully SMBus 1.1 compliant)
The ADT7468 dBCOOLTM controller is a thermal monitor and
multiple PWM fan controller for noise-sensitive or powersensitive applications requiring active system cooling. The
ADT7468 can drive a fan using either a low or high frequency
drive signal, monitor the temperature of up to two remote
sensor diodes plus its own internal temperature, and measure
and control the speed of up to four fans, so that they operate at
the lowest possible speed for minimum acoustic noise.
The automatic fan speed control loop optimizes fan speed for a
given temperature. A unique dynamic TMIN control mode
enables the system thermals/acoustics to be intelligently
managed. The effectiveness of the system’s thermal solution can
be monitored using the THERM input. The ADT7468 also
provides critical thermal protection to the system using the
bidirectional THERM pin as an output to prevent system or
component overheating.
FUNCTIONAL BLOCK DIAGRAM
SCL
SDA SMBALERT
VID5
VID4
ACOUSTIC
ENHANCEMENT
CONTROL
VID3
VID2
SERIAL BUS
INTERFACE
VID1
VID0
PWM1
PWM2
PWM3
PWM REGISTERS
AND
CONTROLLERS
HF & LF
ACOUSTIC
ENHANCEMENT
CONTROL
TACH1
TACH2
AUTOMATIC
FAN SPEED
CONTROL
ADDRESS
POINTER
REGISTER
DYNAMIC
TMIN
CONTROL
PWM
CONFIGURATION
REGISTERS
FAN SPEED
COUNTER
TACH3
TACH4
INTERRUPT
MASKING
PERFORMANCE
MONITORING
THERMAL
PROTECTION
THERM
VCC
INTERRUPT
STATUS
REGISTERS
VCC TO ADT7468
ADT7468
D1+
10-BIT
ADC
SRC
D2–
INPUT
SIGNAL
CONDITIONING
AND
ANALOG
MULTIPLEXER
+5VIN
+12VIN
+2.5VIN
VCCP
BAND GAP
TEMP SENSOR
BAND GAP
REFERENCE
GND
LIMIT
COMPARATORS
VALUE AND
LIMIT
REGISTERS
04499-0-001
D1–
D2+
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
ADT7468
TABLE OF CONTENTS
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
Thermal Characteristics .............................................................. 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 8
Status Registers ........................................................................... 23
THERM Timer ........................................................................... 25
Fan Drive Using PWM Control ............................................... 28
Laying Out 2-Wire and 3-Wire Fans ....................................... 30
Operating from 3.3 V Standby.................................................. 34
Product Description....................................................................... 10
XNOR Tree Test Mode .............................................................. 35
Comparison between ADT7463 and ADT7468 ..................... 10
Power-On Default ...................................................................... 35
How to Set the Functionality of Pin 14 ................................... 11
Programming the Automatic Fan Speed Control Loop ............ 36
Recommended Implementation............................................... 11
Automatic Fan Control Overview............................................ 36
Serial Bus Interface..................................................................... 12
Step 1: Hardware Configuration.............................................. 37
Write Operations ........................................................................ 13
Recommended Implementation 1 ........................................... 38
Read Operations ......................................................................... 14
Recommended Implementation 2 ........................................... 39
SMBus Timeout .......................................................................... 14
Step 2: Configuring the MUX................................................... 40
Voltage Measurement Input...................................................... 14
Step 3: TMIN Settings for Thermal Calibration Channels....... 42
Analog-to-Digital Converter .................................................... 14
Step 4: PWMMIN for Each PWM (Fan) Output....................... 43
Input Circuitry............................................................................ 15
Step 5: PWMMAX for PWM (Fan) Outputs.............................. 43
Voltage Measurement Registers................................................ 15
Step 7: TTHERM for Temperature Channels ............................... 47
Voltage Limit Registers .............................................................. 15
Step 8: THYST for Temperature Channels .................................. 48
VID Code Monitoring ............................................................... 15
Dynamic TMIN Control Mode ................................................... 49
VID Code Input Threshold Voltage......................................... 15
Step 9: Operating Points for Temperature Channels ............. 51
VID Code Change Detect Function ........................................ 16
Step 10: High and Low Limits for Temperature Channels ... 52
Additional ADC Functions for Voltage Measurements ........ 16
Step 11: Monitoring THERM ................................................... 55
Temperature Measurement Method ........................................ 18
Enhancing System Acoustics .................................................... 56
Series Resistance Cancellation.................................................. 19
Step 12: Ramp Rate for Acoustic Enhancement..................... 58
Factors Affecting Diode Accuracy ........................................... 19
Register Tables ................................................................................ 60
Additional ADC Functions for Temperature Measurement. 21
Limits, Status Registers, and Interrupts ....................................... 22
Limit Values................................................................................. 22
ADT7468 Programming Block Diagram .................................... 79
Outline Dimensions ....................................................................... 80
Ordering Guide .......................................................................... 80
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 80
ADT7468
SPECIFICATIONS
TA = TMIN to TMAX, VCC = VMIN to VMAX, unless otherwise noted.
All voltages are measured with respect to GND, unless otherwise specified. Typicals are at TA = 25°C and represent most likely parametric
norm. Logic inputs accept input high voltages up to VMAX even when device is operating down to VMIN. Timing specifications are tested at
logic levels of VIL = 0.8 V for a falling edge and VIH = 2.0 V for a rising edge. SMBus timing specifications are guaranteed by design and are
not production tested.
Table 1.
Parameter
POWER SUPPLY
Supply Voltage
Supply Current, ICC
Min
Typ
Max
Unit
Test Conditions/Comments
3.0
3.3
5.5
3
20
V
mA
µA
Interface inactive, ADC active
Standby mode
±1.5
+2
+2
°C
°C
°C
°C
°C
°C
°C
°C
µA
µΑ
µΑ
0°C ≤ TA ≤ 70°C
−40°C ≤ TA ≤ +100°C
−40°C ≤ TA ≤ +120°C
%
%
LSB
%/V
ms
ms
ms
ms
ms
kΩ
kΩ
For 12 V and 5 V channels
For all other channels
8 bits
Averaging enabled
Averaging enabled
Averaging enabled
Averaging enabled
Averaging disabled
For VCC channel
For all other channels
%
%
%
0°C ≤ TA ≤ 70°C , 3.3 V
−40°C ≤ TA ≤ +120°C , 3.3 V
−40°C ≤ TA ≤ +120°C , 5.5 V
RPM
RPM
RPM
RPM
Fan count = 0xBFFF
Fan count = 0x3FFF
Fan count = 0x0438
Fan count = 0x021C
kHz
kHz
kHz
0°C ≤ TA ≤ 70°C, VCC = 3.3 V
−40°C ≤ TA ≤ +120°C, VCC = 3.3 V
−40°C ≤ TA ≤ +120°C, VCC = 5.5 V
TEMP-TO-DIGITAL CONVERTER
Local Sensor Accuracy
−3.5
−4
Resolution
Remote Diode Sensor Accuracy
0.25
±1.5
+2
+2
−3.5
−4.5
Resolution
Remote Sensor Source Current
0.25
6
36
96
ANALOG-TO-DIGITAL CONVERTER (INCLUDING MUX AND ATTENUATORS)
Total Unadjusted Error (TUE)
Differential Nonlinearity (DNL)
Power Supply Sensitivity
Conversion Time (Voltage Input)
Conversion Time (Local Temperature)
Conversion Time (Remote Temperature)
Total Monitoring Cycle Time
Total Monitoring Cycle Time
Input Resistance
40
80
±0.1
11
12
38
145
19
70
140
FAN RPM-TO-DIGITAL CONVERTER
Accuracy
100
200
±5
±7
±10
65,535
Full-Scale Count
Nominal Input RPM
Internal Clock Frequency
±2
±1.5
±1
109
329
5000
10000
85.5
83.7
81
90
90
90
94.5
96.3
99
Rev. 0 | Page 3 of 80
0°C ≤ TA ≤ 70°C; 0°C ≤ TD ≤ 120°C
−40°C ≤ TA ≤ +100°C; 0°C ≤ TD ≤ +120°C
−40°C ≤ TA ≤ +120°C; 0°C ≤ TD ≤ +120°C
First current
Second current
Third current
ADT7468
Parameter
Min
OPEN-DRAIN DIGITAL OUTPUTS, PWM1 TO PWM3, XTO
Current Sink, IOL
Output Low Voltage, VOL
High Level Output Current, IOH
OPEN-DRAIN SERIAL DATA BUS OUTPUT (SDA)
Output Low Voltage, VOL
High Level Output Current, IOH
SMBUS DIGITAL INPUTS (SCL, SDA)
Input High Voltage, VIH
Input Low Voltage, VIL
Hysteresis
DIGITAL INPUT LOGIC LEVELS (TACH INPUTS)
Input High Voltage, VIH
Typ
Max
Unit
Test Conditions/Comments
0.1
8.0
0.4
1.0
mA
V
µA
IOUT = −8.0 mA, VCC = +3.3 V
VOUT = VCC
0.1
0.4
1.0
V
µA
IOUT = −4.0 mA, VCC = +3.3 V
VOUT = VCC
0.4
V
V
mV
2.0
500
2.0
V
V
V
V
V p-p
5.5
0.8
Input Low Voltage, VIL
−0.3
Hysteresis
DIGITAL INPUT LOGIC LEVELS (THERM) ADTL+
Input High Voltage, VIH
Input Low Voltage, VIL
DIGITAL INPUT CURRENT
Input High Current, IIH
Input Low Current, IIL
Input Capacitance, CIN
SERIAL BUS TIMING
Clock Frequency, fSCLK
Glitch Immunity, tSW
Bus Free Time, tBUF
Start Setup Time, tSU;STA
Start Hold Time, tHD;STA
SCL Low Time, tLOW
SCL High Time, tHIGH
SCL, SDA Rise Time, tR
SCL, SDA Fall Time, tF
Data Setup Time, tSU;DAT
Data Hold Time, tHD;DAT
Detect Clock Low Timeout, tTIMEOUT
tLOW
0.5
0.75 × VCCP
Maximum input voltage
Minimum input voltage
V
V
0.4
−1
µA
µA
pF
1
5
VIN = VCC
VIN = 0
See Figure 2
10
400
50
4.7
4.7
4.0
4.7
4.0
50
1000
300
250
300
15
tR
kHz
ns
µs
µs
µs
µs
µs
ns
µs
ns
ns
ms
35
tF
Can be optionally disabled
tHD; STA
SCL
tHIGH
tHD; DAT
tSU; STA
tSU; STO
tSU; DAT
SDA
tBUF
P
S
S
Figure 2. Serial Bus Timing Diagram
Rev. 0 | Page 4 of 80
P
04499-0-002
tHD; STA
ADT7468
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Positive Supply Voltage (VCC)
Maximum Voltage on 12 VIN Pin
Voltage on Any Input or Output Pin
Input Current at Any Pin
Package Input Current
Maximum Junction Temperature (TJMAX)
Storage Temperature Range
Lead Temperature, Soldering
IR Reflow Peak Temperature
Lead Temperature (Soldering 10 s)
ESD Rating
Rating
5.5 V
20 V
−0.3 V to +6.5 V
±5 mA
±20 mA
150°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
24-lead QSOP package:
220°C
300°C
1000 V
θJA = 150°C/W
θJC = 39°C/W
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 80
ADT7468
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
SDA 1
24
PWM1/XTO
SCL 2
23
VCCP
GND 3
22
+2.5VIN
VCC 4
21
+12VIN/VID5
VID0 5
20
+5VIN/THERM
19
VID4
VID1 6
ADT7468
VID3 8
17
D1–
TACH3 9
16
D2+
PWM2/SMBALERT 10
15
D2–
11
14
TACH4/GPIO/THERM/SMBALERT
TACH2 12
13
PWM3
TACH1
04499-0-003
TOP VIEW
VID2 7 (NOT TO SCALE) 18 D1+
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin
No.
1
2
3
4
Mnemonic
SDA
SCL
GND
VCC
5
6
7
8
9
VID0
VID1
VID2
VID3
TACH3
10
PWM2
SMBALERT
11
TACH1
12
TACH2
13
PWM3
14
TACH4
GPIO
THERM
SMBALERT
15
16
17
D2–
D2+
D1–
Description
Digital I/O (Open Drain). SMBus bidirectional serial data. Requires pull-up resistor.
Digital Input (Open Drain). SMBus serial clock input. Requires pull-up resistor.
Ground Pin.
Power Supply. Can be powered by 3.3 V standby, if monitoring in low power states is required. VCC is also monitored
through this pin. The ADT7468 can also be powered from a 5 V supply. Setting Bit 7 of Configuration Register 1
(Reg. 0x40) rescales the VCC input attenuators to correctly measure a 5 V supply.
Digital Input (Open Drain). Voltage supply readouts from CPU. This value is read into the VID register (Reg. 0x43).
Digital Input (Open Drain). Voltage supply readouts from CPU. This value is read into the VID register (Reg. 0x43).
Digital Input (Open Drain). Voltage supply readouts from CPU. This value is read into the VID register (Reg. 0x43).
Digital Input (Open Drain). Voltage supply readouts from CPU. This value is read into the VID register (Reg. 0x43).
Digital Input (Open Drain). Fan tachometer input to measure speed of Fan 3. Can be reconfigured as an analog input
(AIN3) to measure the speed of 2-wire fans.
Digital Output (Open Drain). Requires 10 kΩ typical pull-up. Pulse width modulated output to control Fan 2 speed.
Can be configured as a high or low frequency drive.
Digital Output (Open Drain). This pin can be reconfigured as an SMBALERT interrupt output to signal out-of-limit
conditions.
Digital Input (Open Drain). Fan tachometer input to measure speed of Fan 1. Can be reconfigured as an analog input
(AIN1) to measure the speed of 2-wire fans.
Digital Input (Open Drain). Fan tachometer input to measure speed of Fan 2. Can be reconfigured as an analog input
(AIN2) to measure the speed of 2-wire fans.
Digital I/O (Open Drain). Pulse width modulated output to control speed of Fan 3 and Fan 4. Requires 10 kΩ typical
pull-up. Can be configured as a high or low frequency drive.
Digital Input (Open Drain). Fan tachometer input to measure speed of Fan 4. Can be reconfigured as an analog input
(AIN4) to measure the speed of 2-wire fans.
General Purpose Open Drain Digital I/O.
Alternatively, the pin can be reconfigured as a bidirectional THERM pin. Can be used to time and monitor assertions
on the THERM input. For example, this pin can be connected to the PROCHOT output of an Intel Pentium 4 processor
or to the output of a trip point temperature sensor. This pin can also be used as an output to signal overtemperature
conditions.
Digital Output (Open Drain). This pin can be reconfigured as an SMBALERT interrupt output to signal out-of-limit
conditions.
Cathode Connection to Second Thermal Diode.
Anode Connection to Second Thermal Diode.
Cathode Connection to First Thermal Diode.
Rev. 0 | Page 6 of 80
ADT7468
Pin
No.
18
19
20
Mnemonic
D1+
VID4
+5VIN
THERM
21
+12VIN
VID5
22
23
24
+2.5VIN
VCCP
PWM1
XTO
Description
Anode Connection to First Thermal Diode.
Digital Input (Open Drain). Voltage supply readouts from CPU. This value is read into the VID register (Reg. 0x43).
Analog Input. Monitors +5 V power supply.
Alternatively, this pin can be reconfigured as a bidirectional THERM pin. Can be used to time and monitor assertions
on the THERM input. For example, it can be connected to the PROCHOT output of an Intel Pentium 4 processor or to
the output of a trip point temperature sensor. This pin can also be used as an output to signal overtemperature
conditions.
Analog Input. Monitors +12 V power supply.
Digital Input (Open Drain). Voltage supply readouts from CPU. This value is read into the VID register (Reg. 0x43).
Supports VRM10 solutions.
Analog Input. Monitors +2.5 V supply, typically a chipset voltage.
Analog Input. Monitors processor core voltage (0 V to 3 V).
Digital Output (Open Drain). Pulse width modulated output to control Fan 1 speed. Requires 10 kΩ typical pull-up.
Also functions as the output from the XOR tree in XOR test mode.
Rev. 0 | Page 7 of 80
ADT7468
0
20
–10
15
TEMPERATURE ERROR (°C)
TEMPERATURE ERROR (°C)
TYPICAL PERFORMANCE CHARACTERISTICS
–20
–30
–40
100mV
10
40mV
5
0
–5
–50
–60
0
1
2.2
3.3
CAPACITANCE (nF)
4.7
10
100
1M
10M
FREQUENCY (kHz)
100M
1G
Figure 7. Remote Temperature Error vs. Common Mode Noise Frequency
0
6
–10
5
–20
4
TEMPERATURE ERROR (°C)
–30
–40
–50
–60
–70
–80
20mV
3
2
1
0
10mV
–1
–2
–3
–100
0
5
10
15
CAPACITANCE (nF)
20
25
04499-0-046
–90
–4
10
Figure 5. External Temperature Error vs. D+/D− Capacitance
100
1M
10M
FREQUENCY (kHz)
100M
04499-0-049
TEMPERATURE ERROR (°C)
Figure 4. Temperature Error vs. Capacitance between D+ and D−
–10
10
04499-0-048
04499-0-045
60mV
1G
Figure 8. Remote Temperature Error vs. Differential Mode Noise Frequency
60
1.40
1.35
20
1.30
0
1.25
D+ TO VCC
–20
1.20
–40
1.15
–60
1.10
–80
0
1
3.3
10
RESISTANCE (MΩ)
20
100
Figure 6. Remote Temperature Error vs. PCB Resistance
1.05
3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
POWER SUPPLY VOLTAGE (V)
Figure 9. Normal IDD vs. Power Supply
Rev. 0 | Page 8 of 80
04499-0-050
IDD (mA)
40
04499-0-047
TEMPERATURE ERROR (°C)
D+ TO GND
ADT7468
1.0
7
0.5
6
0
5
ERROR (°C)
–0.5
IDD (µA)
4
3
–1.0
–1.5
–2.0
–2.5
2
–3.0
1
–4.0
–40
Figure 10. Shutdown IDD vs. Power Supply
–20
0
20
40
60
TEMPERATURE (°C)
80
100
120
04499-0-091
04499-0-051
–3.5
0
3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
POWER SUPPLY VOLTAGE (V)
Figure 13. Internal Temperature Error vs. ADT7468 Temperature
0.5
15
0
–0.5
INT ERROR, 250mV
10
ERROR (°C)
5
0
–1.5
–2.0
–2.5
–5
–10
–1.0
–3.0
INT ERROR, 100mV
–3.5
–20
10
100
1M
10M
100M
POWER SUPPLY NOISE FREQUENCY (kHz)
1G
04499-0-052
–15
–4.0
–40
–20
0
20
40
60
TEMPERATURE (°C)
80
100
120
Figure 14. Remote Temperature Error vs. ADT7468 Temperature
Figure 11. Internal Temperature Error vs. Power Supply
20
EXT ERROR, 250mV
TEMPERATURE ERROR (°C)
15
10
5
0
EXT ERROR, 100mV
–5
–10
–20
10
100
1M
10M
100M
POWER SUPPLY NOISE FREQUENCY (kHz)
1G
04499-0-053
–15
Figure 12. Remote Temperature Error vs. Power Supply Noise Frequency
Rev. 0 | Page 9 of 80
04499-0-092
TEMPERATURE ERROR (°C)
1.0
20
ADT7468
PRODUCT DESCRIPTION
The ADT7468 is a complete thermal monitor and multiple fan
controller for any system requiring thermal monitoring and
cooling. The device communicates with the system via a serial
system management bus. The serial bus controller has a serial
data line for reading and writing addresses and data (Pin 1), and
an input line for the serial clock (Pin 2). All control and
programming functions for the ADT7468 are performed over
the serial bus. In addition, a pin can be reconfigured as an
SMBALERT output to signal out-of-limit conditions.
5.
The ADT7468 has an extended temperature measurement
range. The measurement range goes from–64°C to +191°C.
On the ADT7463, the measurement range is from −127°C
to +127°C. This means that the ADT7468 can measure
higher temperatures. The ADT7468 also includes the
ADT7463 temperature range; the temperature measurement range can be switched by setting Bit 0 of
Configuration Register 5.
6.
The ADT7468 maximum fan speed (% duty cycle) in the
automatic fan speed control loop can be programmed. The
maximum fan speed is 100% duty cycle on the ADT7463
and is not programmable.
7.
The offset register in the ADT7468 is programmable up to
±64°C with 0.50°C resolution. The offset register of the
ADT7463 is programmable up to ±32°C with 0.25°C
resolution.
8.
VCCP is monitored on Pin 23 of the ADT7468 and can be
used to set the threshold for THERM (PROCHOT) (2/3 of
VCCP). The threshold for THERM (PROCHOT) is set at
VIH = 1.7 V and VIL = 0.8 V on the ADT7463.
9.
On the ADT7463, Pin 22 can be reconfigured as SMBus
ALERT. This is not available on the ADT7468; instead,
SMBALERT can be enabled on Pin 14.
COMPARISON BETWEEN ADT7463 AND ADT7468
The ADT7468 is an upgrade to the ADT7463. The ADT7468
and ADT7463 are almost pin and register map compatible. The
ADT7468 and ADT7463 have the following differences:
1.
2.
3.
On the ADT7468, the PWM drive signals can be configured as either high frequency or low frequency drives. The
low frequency option is programmable between 10 Hz and
100 Hz. The high frequency option is 22.5 kHz. On the
ADT7463, only the low frequency option is available.
Once the VCC is powered up, monitoring of temperature
and fan speeds is enabled on the ADT7468 when VCCP is
powered up, or if VCCP is never powered up, when the first
SMBus transaction with the ADT7468 is completed. On the
ADT7463, the STRT bit in Configuration Register 1 must
be set to enable monitoring.
The fans are switched off by default on power-up on the
ADT7468. On the ADT7463, the fans run at full speed on
power-up.
Fail-safe cooling is provided on the ADT7468 in that, if the
measured temperature exceeds the THERM limit (100°C),
the fans run at full speed.
Fail-safe cooling is also provided 4.6 s after VCCP is powered
up. See Figure 48. The fans go to full speed, if the ADT7468
has not been addressed via the SMBus within 4.6 s of when
the VCCP is powered up. This protects the system in the
event that the SMBus fails. The ADT7468 can be programmed at any time, either before or after the 4.6 s has
elapsed, and it behaves as programmed. If VCCP is never
powered up, fail-safe cooling is effectively disabled. If VCCP
is disabled, writing to the ADT7468 at any time causes the
ADT7468 to operate normally.
4.
Series resistance cancellation (SRC) is provided on the
remote temperature channels on the ADT7468, but not on
the ADT7463. SRC automatically cancels linear offset
introduced by a series resistance between the thermal
diode and the sensor.
10. A GPIO can also be made available on Pin 14 on the
ADT7468. This is not available on the ADT7463. Set the
GPIO polarity and direction in Configuration Register 5.
The GPIO status bit is Bit 5 of Status Register 2 (shared
with TACH4 and THERM, because only one can be
enabled at a time).
11. The ADT7463 has three possible SMBus addresses, which
are selectable using the address select and address enable
pins. The ADT7468 has one SMBus address available at
Address 0x2E.
Due to the inclusion of extra functionality, the register map has
changed, including an additional configuration register:
Configuration Register 5 at Address 0x7C.
Configuration Register 5
Bit 0: If Bit 0 is set to 1, the ADT7468 is backward compatible
temperature-wise with the ADT7463. Measurements, TMIN
calibration circuit, fan control, etc., work in the range −127°C to
+127°C. Also, care should be taken in reprogramming the
temperature limits (TMIN, operating point, THERM limits) to
their desired twos complement value, because the power-on
default for them is at Offset 64. The extended temperature range
is −64°C to 191°C. The default is 1, which is in the −64°C to
+191°C temperature range.
Rev. 0 | Page 10 of 80
ADT7468
Bit 1= 0 is the high frequency (22.5 kHz) fan drive signal.
RECOMMENDED IMPLEMENTATION
Bit 1 = 1 switches the fan drive to low frequency PWM,
programmable between 10 Hz and 100 Hz, the same as the
ADT7463. The default = 0 = HF PWM.
Configuring the ADT7468 as in Figure 15 allows the system
designer to use the following features:
•
Two PWM outputs for fan control of up to three fans (the
front and rear chassis fans are connected in parallel).
Bit 3 sets the GPIO polarity: 0 = active low, 1 = active high.
•
Three TACH fan speed measurement inputs.
HOW TO SET THE FUNCTIONALITY OF PIN 14
•
VCC measured internally through Pin 3.
Pin 14 on the ADT7468 has four possible functions:
SMBALERT, THERM, GPIO, and TACH4. The user chooses the
required functionality by setting Bit 0 and Bit 1 of Configuration Register 4 at Address 0x7D.
•
CPU temperature measured using Remote 1 temperature
channel.
•
Ambient temperature measured through Remote 2
temperature channel.
•
Bidirectional THERM pin. This feature allows Intel
Pentium 4 PROCHOT monitoring and can function as an
overtemperature THERM output. It can alternatively be
programmed as an SMBALERT system interrupt output.
Bit 2 sets the direction for the GPIO: 0 = input, 1 = output.
Table 4. Pin 14 Settings
Bit 1
Function
TACH4
THERM
SMBALERT
GPIO
CPU FAN
ADT7468
FRONT
CHASSIS
FAN
TACH2
PWM1
TACH1
PWM3
REAR
CHASSIS
FAN
TACH3
5(VRM9)/6(VRM10)
VID[0:4]/VID[0:5]
D2+
D2–
THERM
PROCHOT
D1+
AMBIENT
TEMPERATURE
CPU
D1–
3.3VSB
5V
SDA
12V/VID5
ADP316x
VRM
CONTROLLER
VCOMP
SCL
CURRENT
VCORE
SMBALERT
GND
Figure 15. ADT7468 Configuration
Rev. 0 | Page 11 of 80
ICH
04499-0-004
Bit 0
00
01
10
11
ADT7468
SERIAL BUS INTERFACE
In the ADT7468, write operations contain either one or two
bytes, and read operations contain one byte and perform the
following functions. To write data to one of the device data
registers or read data from it, the address pointer register must
be set so that the correct data register is addressed, then data
can be written into that register or read from it. The first byte of
a write operation always contains an address that is stored in the
address pointer register. If data is to be written to the device,
then the write operation contains a second data byte that is
written to the register selected by the address pointer register.
On PCs and servers, control of the ADT7468 is carried out
using the serial system management bus (SMBus). The
ADT7468 is connected to this bus as a slave device, under the
control of a master controller, which is usually (but not
necessarily) the ICH.
The ADT7468 has a fixed 7-bit serial bus address of 0101110 or
0x2E. The read/write bit must be added to get the 8-bit address
(01011100 or 0x5C). Data is sent over the serial bus in
sequences of nine clock pulses: eight bits of data followed by an
acknowledge bit from the slave device. Transitions on the data
line must occur during the low period of the clock signal and
remain stable during the high period, because a low-to-high
transition when the clock is high might be interpreted as a stop
signal. The number of data bytes that can be transmitted over
the serial bus in a single read or write operation is limited only
by what the master and slave devices can handle.
This write operation is illustrated in Figure 16. The device
address is sent over the bus, and then R/W is set to 0. This is
followed by two data bytes. The first data byte is the address of
the internal data register to be written to, which is stored in the
address pointer register. The second data byte is the data to be
written to the internal data register.
When reading data from a register, there are two possibilities:
When all data bytes have been read or written, stop conditions
are established. In write mode, the master pulls the data line
high during the tenth clock pulse to assert a stop condition. In
read mode, the master device overrides the acknowledge bit by
pulling the data line high during the low period before the
ninth clock pulse. This is known as No Acknowledge. The
master then takes the data line low during the low period before
the tenth clock pulse, and then high during the tenth clock
pulse to assert a stop condition.
•
A read operation is then performed consisting of the serial
bus address, R/W bit set to 1, followed by the data byte read
from the data register. This is shown in Figure 18.
Any number of bytes of data can be transferred over the serial
bus in one operation, but it is not possible to mix read and write
in one operation, because the type of operation is determined at
the beginning and cannot subsequently be changed without
starting a new operation.
1
If the ADT7468’s address pointer register value is unknown
or not the desired value, it must first be set to the correct
value before data can be read from the desired data register.
This is done by performing a write to the ADT7468 as
before, but only the data byte containing the register
address is sent, because no data is written to the register.
This is shown in Figure 17.
•
9
If the address pointer register is known to be already at the
desired address, data can be read from the corresponding
data register without first writing to the address pointer
register, as shown in Figure 18.
9
1
SCL
0
1
0
1
1
1
0
START BY
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
D7
R/W
D6
ACK. BY
ADT7468
D5
D4
D3
D2
D1
D0
ACK. BY
ADT7468
FRAME 2
ADDRESS POINTER REGISTER BYTE
1
9
SCL (CONTINUED)
SDA (CONTINUED)
D7
D6
D5
D4
D3
D2
FRAME 3
DATA BYTE
D1
D0
ACK. BY
ADT7468
Figure 16. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register
Rev. 0 | Page 12 of 80
STOP BY
MASTER
04499-0-005
SDA
ADT7468
1
9
9
1
SCL
0
1
START BY
MASTER
0
1
1
1
0
D7
R/W
D6
ACK. BY
ADT7468
FRAME 1
SERIAL BUS ADDRESS BYTE
D4
D5
D2
D3
D1
D0
ACK. BY
ADT7468
FRAME 2
ADDRESS POINTER REGISTER BYTE
STOP BY
MASTER
04499-0-006
SDA
Figure 17. Writing to the Address Pointer Register Only
1
9
9
1
SCL
0
1
START BY
MASTER
0
1
1
1
0
R/W
D7
D6
ACK. BY
ADT7468
FRAME 1
SERIAL BUS ADDRESS BYTE
D5
D4
D2
D3
D1
FRAME 2
DATA BYTE FROM ADT7468
D0
NO ACK. BY STOP BY
MASTER
MASTER
04499-0-007
SDA
Figure 18. Reading Data from a Previously Selected Register
In addition to supporting the send byte and receive byte
protocols, the ADT7468 also supports the read byte protocol.
(see System Management Bus Specifications Rev. 2 for more
information. This document is available from Intel.)
If several read or write operations must be performed in
succession, the master can send a repeat start condition instead
of a stop condition to begin a new operation.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends a command code.
5.
The slave asserts ACK on SDA.
6.
The master asserts a stop condition on SDA and the
transaction ends.
For the ADT7468, the send byte protocol is used to write a
register address to RAM for a subsequent single byte read from
the same address. This operation is illustrated in Figure 19.
1
WRITE OPERATIONS
The SMBus specification defines several protocols for different
types of read and write operations. The ones used in the
ADT7468 are discussed below. The following abbreviations are
used in the diagrams:
S – START
P – STOP
R – READ
W – WRITE
A – ACKNOWLEDGE
A – NO ACKNOWLEDGE
2
3
SLAVE
S
W A
ADDRESS
4
5 6
REGISTER
ADDRESS
A P
04499-0-008
It is possible to read a data byte from a data register without
first writing to the address pointer register, if the address
pointer register is already at the correct value. However, it is not
possible to write data to a register without writing to the address
pointer register, because the first data byte of a write is always
written to the address pointer register.
Figure 19. Setting a Register Address for Subsequent Read
If the master is required to read data from the register
immediately after setting up the address, it can assert a repeat
start condition immediately after the final ACK and carry out a
single byte read without asserting an intermediate stop
condition.
Write Byte
In this operation, the master device sends a command byte and
one data byte to the slave device, as follows:
The ADT7468 uses the following SMBus write protocols.
1.
The master device asserts a start condition on SDA.
Send Byte
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends a command code.
In this operation, the master device sends a single command
byte to a slave device as follows:
1.
The master device asserts a start condition on SDA.
Rev. 0 | Page 13 of 80
ADT7468
5.
The slave asserts ACK on SDA.
1.
SMBALERT is pulled low.
6.
The master sends a data byte.
2.
7.
The slave asserts ACK on SDA.
The master initiates a read operation and sends the alert
response address (ARA = 0001 100). This is a general call
address that must not be used as a specific device address.
8.
The master asserts a stop condition on SDA to end the
transaction.
3.
The device whose SMBALERT output is low responds to
the alert response address, and the master reads its device
address. The address of the device is now known and can
be interrogated in the usual way.
4.
If more than one device’s SMBALERT output is low, the
one with the lowest device address has priority in accordance with normal SMBus arbitration.
5.
Once the ADT7468 has responded to the alert response
address, the master must read the status registers and the
SMBALERT is cleared only if the error condition has gone
away.
This operation is illustrated in Figure 20.
2
3
SLAVE
S
W A
ADDRESS
4
5
SLAVE
ADDRESS
6
7 8
A DATA A P
04499-0-009
1
Figure 20. Single Byte Write to a Register
READ OPERATIONS
The ADT7468 uses the following SMBus read protocols.
Receive Byte
This operation is useful when repeatedly reading a single
register. The register address must have been set up previously.
In this operation, the master device receives a single byte from a
slave device as follows:
SMBUS TIMEOUT
1.
The master device asserts a start condition on SDA.
2.
The master sends the 7-bit slave address followed by the
read bit (high).
The ADT7468 includes an SMBus timeout feature. If there is no
SMBus activity for 35 ms, the ADT7468 assumes that the bus is
locked and releases the bus. This prevents the device from
locking or holding the SMBus expecting data. Some SMBus
controllers cannot handle the SMBus timeout feature, so it can
be disabled.
3.
The addressed slave device asserts ACK on SDA.
Configuration Register 1(Reg. 0x40)
4.
The master receives a data byte.
5.
The master asserts NO ACK on SDA.
6.
The master asserts a stop condition on SDA and the
transaction ends.
<6> TODIS = 0, SMBus timeout enabled (default).
<6> TODIS = 1, SMBus timeout disabled.
VOLTAGE MEASUREMENT INPUT
In the ADT7468, the receive byte protocol is used to read a
single byte of data from a register whose address has previously
been set by a send byte or write byte operation. This operation
is illustrated in Figure 21.
2
3
SLAVE
S
R A
ADDRESS
4
5
6
DATA A P
04499-0-010
1
Figure 21. Single Byte Read from a Register
The ADT7468 has four external voltage measurement channels.
It can also measure its own supply voltage, VCC. Pins 20 to 23
can measure 5 V, 12 V, and 2.5 V supplies, and the processor
core voltage VCCP (0 V to 3 V input). The VCC supply voltage
measurement is carried out through the VCC pin (Pin 4). Setting
Bit 7 of Configuration Register 1 (Reg. 0x40) allows a 5 V
supply to power the ADT7468 and be measured without
overranging the VCC measurement channel. The 2.5 V input can
be used to monitor a chipset supply voltage in computer
systems.
ANALOG-TO-DIGITAL CONVERTER
Alert Response Address
Alert response address (ARA) is a feature of SMBus devices that
allows an interrupting device to identify itself to the host when
multiple devices exist on the same bus.
The SMBALERT output can be used as either an interrupt
output or an SMBALERT. One or more outputs can be
connected to a common SMBALERT line connected to the
master. If a device’s SMBALERT line goes low, the following
procedure occurs:
All analog inputs are multiplexed into the on-chip, successiveapproximation, analog-to-digital converter. This has a resolution of 10 bits. The basic input range is 0 V to 2.25 V, but the
inputs have built-in attenuators to allow measurement of 2.5 V,
3.3 V, 5 V, 12 V, and the processor core voltage VCCP without any
external components. To allow for the tolerance of these supply
voltages, the ADC produces an output of 3/4 full scale (decimal
768 or 300 hex) for the nominal input voltage and so has
adequate headroom to cope with overvoltages.
Rev. 0 | Page 14 of 80
ADT7468
INPUT CIRCUITRY
Reg. 0x4C, 12 V Low Limit = 0x00 default
The internal structure for the analog inputs is shown in
Figure 22. The input circuit consists of an input protection
diode, an attenuator, plus a capacitor to form a first-order lowpass filter that gives input immunity to high frequency noise.
Reg. 0x4D, 12 V High Limit = 0xFF default
5VIN
3.3VIN
2.5VIN
VCCP
120kΩ
20kΩ
30pF
47kΩ
30pF
When the ADC is running, it samples and converts a voltage
input in 0.7 ms and averages 16 conversions to reduce noise; a
measurement takes nominally 11 ms.
93kΩ
VID CODE MONITORING
The ADT7468 has five dedicated voltage ID (VID code)
inputs. These are digital inputs that can be read back through
the VID register (Reg. 0x43) to determine the processor voltage
required or being used in the system. Five VID code inputs
support VRM9.x solutions. In addition, Pin 21 (12 V input) can
be reconfigured as a sixth VID input to satisfy future VRM
requirements.
68kΩ
71kΩ
30pF
94kΩ
30pF
MUX
45kΩ
17.5kΩ
52.5kΩ
VID Code Register (Reg. 0x43)
35pF
04499-0-011
12VIN
Table 5 shows the input ranges of the analog inputs and output
codes of the 10-bit ADC.
<0> = VID0, reflects logic state of Pin 5.
<1> = VID1, reflects logic state of Pin 6.
Figure 22. Structure of Analog Inputs
<2> = VID2, reflects logic state of Pin 7.
VOLTAGE MEASUREMENT REGISTERS
<3> = VID3, reflects logic state of Pin 8.
Reg. 0x20, 2.5 V Reading = 0x00 default
<4> = VID4, reflects logic state of Pin 19.
Reg. 0x21, VCCP Reading = 0x00 default
<5> = VID5, reconfigurable 12 V input. This bit reads 0 when
Pin 21 is configured as the 12 V input. This bit reflects the logic
state of Pin 21 when the pin is configured as VID5.
Reg. 0x22, VCC Reading = 0x00 default
Reg. 0x23, 5 V Reading = 0x00 default
VID CODE INPUT THRESHOLD VOLTAGE
Reg. 0x24, 12 V Reading = 0x00 default
VOLTAGE LIMIT REGISTERS
Associated with each voltage measurement channel is a high
and low limit register. Exceeding the programmed high or low
limit causes the appropriate status bit to be set. Exceeding either
limit can also generate SMBALERT interrupts.
Reg. 0x44, 2.5 V Low Limit = 0x00 default
The switching threshold for the VID code inputs is approximately 1 V. To enable future compatibility, it is possible to
reduce the VID code input threshold to 0.6 V. Bit 6 (THLD) of
the VID register (Reg. 0x43) controls the VID input threshold
voltage.
VID CODE REGISTER (Reg. 0x43)
<6> THLD = 0, VID switching threshold = 1 V,
VOL < 0.8 V, VIH > 1.7 V, VMAX = 3.3 V
Reg. 0x45, 2.5 V High Limit = 0xFF default
THLD = 1, VID switching threshold = 0.6 V,
VOL < 0.4 V, VIH > 0.8 V, VMAX = 3.3 V
Reg. 0x46, VCCP Low Limit = 0x00 default
Reconfiguring Pin 21 as VID5 Input
Reg. 0x47, VCCP High Limit = 0xFF default
Reg. 0x48, VCC Low Limit = 0x00 default
Reg. 0x49, VCC High Limit = 0xFF default
Reg. 0x4A, 5 V Low Limit = 0x00 default
Reg. 0x4B, 5 V High Limit = 0xFF default
Pin 21 can be reconfigured as a sixth VID code input (VID5)
for VRM10 compatible systems. Because the pin is configured
as VID5, it is not possible to monitor a 12 V supply.
Bit 7 of the VID register (Reg. 0x43) determines the function of
Pin 21. System or BIOS software can read the state of Bit 7 to
determine whether the system is designed to monitor 12 V or is
monitoring a sixth VID input.
Rev. 0 | Page 15 of 80
ADT7468
VID Code Register (Reg. 0x43)
<7> VIDSEL = 0, Pin 21 functions as a 12 V measurement
input. Software can read this bit to determine that there are five
VID inputs being monitored. Bit 5 of Register 0x43 (VID5)
always reads back 0. Bit 0 of Status Register 2 (Reg. 0x42)
reflects 12 V out-of-limit measurements.
VIDSEL = 1, Pin 21 functions as the sixth VID code input
(VID5). Software can read this bit to determine that there are
six VID inputs being monitored. Bit 5 of Register 0x43 reflects
the logic state of Pin 21. Bit 0 of Status Register 2 (Reg. 0x42)
reflects VID code changes.
instances where faster conversions are needed, setting Bit 4 of
Configuration Register 2 (Reg. 0x73) turns averaging off. This
effectively gives a reading 16 times faster (0.7 ms), but the
reading may be noisier.
Bypass Voltage Input Attenuator
Setting Bit 5 of Configuration Register 2 (Reg. 0x73) removes
the attenuation circuitry from the 2.5 V, VCCP, VCC, 5 V, and 12 V
inputs. This allows the user to directly connect external sensors
or rescale the analog voltage measurement inputs for other
applications. The input range of the ADC without the
attenuators is 0 V to 2.25 V.
Single-Channel ADC Conversion
VID CODE CHANGE DETECT FUNCTION
The ADT7468 has a VID code change detect function. When
Pin 21 is configured as the VID5 input, VID code changes can
be detected and reported back by the ADT7468. Bit 0 of Status
Register 2 (Reg. 0x42) is the 12 V/VC bit and denotes a VID
change when set. The VID code change bit is set when the logic
states on the VID inputs are different than they were 11 µs
previously. The change of VID code can be used to generate an
SMBALERT interrupt. If an SMBALERT interrupt is not
required, Bit 0 of Interrupt Mask Register 2 (Reg. 0x75), when
set, prevents SMBALERTs from occurring on VID code
changes.
Status Register 2 (Reg. 0x42)
<0> 12V/VC = 0, if Pin 21 is configured as VID5, then Logic 0
denotes no change in VID code within the last 11 µs.
<0> 12V/VC = 1, if Pin 21 is configured as VID5, then Logic 1
means that a change has occurred on the VID code inputs
within the last 11 µs. An SMBALERT is generated, if this
function is enabled.
Setting Bit 6 of Configuration Register 2 (Reg. 0x73) places the
ADT7468 into single-channel ADC conversion mode. In this
mode, the ADT7468 can be made to read a single voltage
channel only. If the internal ADT7468 clock is used, the selected
input is read every 0.7 ms. The appropriate ADC channel is
selected by writing to Bits <7:5> of the TACH1 minimum high
byte register (0x55).
Bits <7:5> Reg. 0x55
000
001
010
011
100
101
110
111
Channel Selected
2.5 V
VCCP
VCC
5V
12 V
Remote 1 Temperature
Local Temperature
Remote 2 Temperature
Configuration Register 2 (Reg. 0x73)
<4> = 1, averaging off.
<5> = 1, bypass input attenuators.
ADDITIONAL ADC FUNCTIONS FOR VOLTAGE
MEASUREMENTS
<6> = 1, single-channel convert mode.
A number of other functions are available on the ADT7468 to
offer the system designer increased flexibility.
TACH1 Minimum High Byte (Reg. 0x55)
<7:5> Selects ADC channel for single-channel convert mode.
Turn-Off Averaging
For each voltage measurement read from a value register,
16 readings have actually been made internally and the results
averaged before being placed into the value register. For
Rev. 0 | Page 16 of 80
ADT7468
Table 5. 10-Bit A/D Output Code vs. VIN
12 VIN
<0.0156
0.0156–0.0312
0.0312–0.0469
0.0469–0.0625
0.0625–0.0781
0.0781–0.0937
0.0937–0.1093
0.1093–0.1250
0.1250–0.1406
4.0000–4.0156
8.0000–8.0156
12.0000–12.0156
15.8281–15.8437
15.8437–15.8593
15.8593–15.8750
15.8750–15.8906
15.8906–15.9062
15.9062–15.9218
15.9218–15.9375
15.9375–15.9531
15.9531–15.9687
15.9687–15.9843
>15.9843
5 VIN
<0.0065
0.0065–0.0130
0.0130–0.0195
0.0195–0.0260
0.0260–0.0325
0.0325–0.0390
0.0390–0.0455
0.0455–0.0521
0.0521–0.0586
•
•
•
1.6675–1.6740
•
•
•
3.3300–3.3415
•
•
•
5.0025–5.0090
•
•
•
6.5983–6.6048
6.6048–6.6113
6.6113–6.6178
6.6178–6.6244
6.6244–6.6309
6.6309–6.6374
6.6374–6.4390
6.6439–6.6504
6.6504–6.6569
6.6569–6.6634
>6.6634
Input Voltage
VCC (3.3 VIN)1
<0.0042
0.0042–0.0085
0.0085–0.0128
0.0128–0.0171
0.0171–0.0214
0.0214–0.0257
0.0257–0.0300
0.0300–0.0343
0.0343–0.0386
2.5 VIN
<0.0032
0.0032–0.0065
0.0065–0.0097
0.0097–0.0130
0.0130–0.0162
0.0162–0.0195
0.0195–0.0227
0.0227–0.0260
0.0260–0.0292
VCCP
<0.00293
0.0293–0.0058
0.0058–0.0087
0.0087–0.0117
0.0117–0.0146
0.0146–0.0175
0.0175–0.0205
0.0205–0.0234
0.0234–0.0263
Decimal
0
1
2
3
4
5
6
7
8
A/D Output
Binary (10 Bits)
00000000 00
00000000 01
00000000 10
00000000 11
00000001 00
00000001 01
00000001 10
00000001 11
00000010 00
1.1000–1.1042
0.8325–0.8357
0.7500–0.7529
256 (1/4 scale)
01000000 00
2.2000–2.2042
1.6650–1.6682
1.5000–1.5029
512 (1/2 scale)
10000000 00
3.3000–3.3042
2.4975–2.5007
2.2500–2.2529
768 (3/4 scale)
11000000 00
4.3527–4.3570
4.3570–4.3613
4.3613–4.3656
4.3656–4.3699
4.3699–4.3742
4.3742–4.3785
4.3785–4.3828
4.3828–4.3871
4.3871–4.3914
4.3914–4.3957
>4.3957
3.2942–3.2974
3.2974–3.3007
3.3007–3.3039
3.3039–3.3072
3.3072–3.3104
3.3104–3.3137
3.3137–3.3169
3.3169–3.3202
3.3202–3.3234
3.3234–3.3267
>3.3267
2.9677–2.9707
2.9707–2.9736
2.9736–2.9765
2.9765–2.9794
2.9794–2.9824
2.9824–2.9853
2.9853–2.9882
2.9882–2.9912
2.9912–2.9941
2.9941–2.9970
>2.9970
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
11111101 01
11111101 10
11111101 11
11111110 00
11111110 01
11111110 10
11111110 11
11111111 00
11111111 01
11111111 10
11111111 11
1
The VCC output codes listed assume that VCC is 3.3 V. If VCC input is reconfigured for 5 V operation (by setting Bit 7 of Configuration Register 1), then the VCC output codes
are the same as for the 5 VIN column.
Rev. 0 | Page 17 of 80
ADT7468
This is given by
A simple method of measuring temperature is to exploit the
negative temperature coefficient of a diode, measuring the baseemitter voltage (VBE) of a transistor, operated at constant
current. Unfortunately, this technique requires calibration to
null out the effect of the absolute value of VBE, which varies
from device to device.
The technique used in the ADT7468 is to measure the change in
VBE when the device is operated at three different currents.
Previous devices have used only two operating currents, but the
use of a third current allows automatic cancellation of
resistances in series with the external temperature sensor.
Figure 24 shows the input signal conditioning used to measure
the output of an external temperature sensor. This figure shows
the external sensor as a substrate transistor, but it could equally
be a discrete transistor. If a discrete transistor is used, the
collector is not grounded and should be linked to the base. To
prevent ground noise from interfering with the measurement,
the more negative terminal of the sensor is not referenced to
ground, but is biased above ground by an internal diode at the
D− input. C1 can optionally be added as a noise filter
(recommended maximum value 1000 pF). However, a better
option in noisy environments is to add a filter, as described in
the Noise Filtering section.
Local Temperature Measurement
The ADT7468 contains an on-chip band gap temperature
sensor whose output is digitized by the on-chip 10-bit ADC.
The 8-bit MSB temperature data is stored in the local temperature register (Address 26h). Because both positive and negative
temperatures can be measured, the temperature data is stored in
Offset 64 format or twos complement format, as shown in
Table 6 and Table 7. Theoretically, the temperature sensor and
ADC can measure temperatures from −128°C to +127°C (or
−61°C to +191°C in the extended temperature range) with a
resolution of 0.25°C. However, this exceeds the operating
temperature range of the device, so local temperature
measurements outside the ADT7468 operating temperature
range are not possible.
Remote Temperature Measurement
The ADT7468 can measure the temperature of two remote
diode sensors or diode-connected transistors connected to Pins
17 and 18, or 15 and 16.
The forward voltage of a diode or diode-connected transistor
operated at a constant current exhibits a negative temperature
coefficient of about –2 mV/°C. Unfortunately, the absolute value
of VBE varies from device to device and individual calibration is
required to null this out, so the technique is unsuitable for mass
production. The technique used in the ADT7468 is to measure
the change in VBE when the device is operated at three different
currents.
∆V BE = KT / q × 1n( N )
where:
K is Boltzmann’s constant.
q is the charge on the carrier.
T is the absolute temperature in Kelvin.
N is the ratio of the two currents.
Figure 23 shows the input signal conditioning used to measure
the output of a remote temperature sensor. This figure shows
the external sensor as a substrate transistor, provided for
temperature monitoring on some microprocessors. It could also
be a discrete transistor such as a 2N3904/2N3906.
I
N2 × I N1 × I IBIAS
VDD
REMOTE
SENSING
TRANSISTOR
VOUT+
D+
TO ADC
D–
LPF
fC = 65kHz
VOUT–
04499-0-012
TEMPERATURE MEASUREMENT METHOD
Figure 23. Signal Conditioning for Remote Diode Temperature Sensors
If a discrete transistor is used, the collector is not grounded and
should be linked to the base. If a PNP transistor is used, the base
is connected to the D– input and the emitter to the D+ input. If
an NPN transistor is used, the emitter is connected to the D–
input and the base to the D+ input. Figure 25 and Figure 26
show how to connect the ADT7468 to an NPN or PNP
transistor for temperature measurement. To prevent ground
noise from interfering with the measurement, the more negative
terminal of the sensor is not referenced to ground, but is biased
above ground by an internal diode at the D– input.
To measure ∆VBE, the operating current through the sensor is
switched among three related currents. Shown in Figure 23,
N1 × I and N2 × I are different multiples of the current I. The
currents through the temperature diode are switched between
I and N1 × I, giving ∆VBE1, and then between I and N2 × I,
giving ∆VBE2. The temperature can then be calculated using
the two ∆VBE measurements. This method can also cancel the
effect of any series resistance on the temperature measurement.
The resulting ∆VBE waveforms are passed through a 65 kHz
low-pass filter to remove noise and then to a chopper-stabilized
amplifier. This amplifies and rectifies the waveform to produce
a dc voltage proportional to ∆VBE. The ADC digitizes this
voltage, and a temperature measurement is produced. To reduce
the effects of noise, digital filtering is performed by averaging
the results of 16 measurement cycles.
Rev. 0 | Page 18 of 80
ADT7468
The results of remote temperature measurements are stored in
10-bit, twos complement format, as illustrated in Table 6. The
extra resolution for the temperature measurements is held in
the Extended Resolution Register 2 (Reg. 0x77). This gives
temperature readings with a resolution of 0.25°C.
Noise Filtering
For temperature sensors operating in noisy environments,
previous practice was to place a capacitor across the D+ and D−
pins to help combat the effects of noise. However, large capacitances affect the accuracy of the temperature measurement,
leading to a recommended maximum capacitor value of 1000 pF.
This capacitor reduces the noise, but does not eliminate it, making
use the sensor difficult in a very noisy environment.
The ADT7468 has a major advantage over other devices for
eliminating the effects of noise on the external sensor. Using the
series resistance cancellation feature, a filter can be constructed
between the external temperature sensor and the part. The effect
of any filter resistance seen in series with the remote sensor is
automatically canceled from the temperature result.
FACTORS AFFECTING DIODE ACCURACY
Remote Sensing Diode
The ADT7468 is designed to work with either substrate
transistors built into processors or with discrete transistors.
Substrate transistors are generally PNP types with the collector
connected to the substrate. Discrete types can be either PNP or
NPN transistors connected as a diode (base-shorted to the
collector). If an NPN transistor is used, the collector and base
are connected to D+ and the emitter to D−. If a PNP transistor
is used, the collector and base are connected to D− and the
emitter is connected to D+.
To reduce the error due to variations in both substrate and
discrete transistors, a number of factors should be taken into
consideration:
•
The construction of a filter allows the ADT7468 and the remote
temperature sensor to operate in noisy environments. Figure 24
shows a low-pass R-C-R filter, with the following values :
∆T = (nf − 1.008) × (273.15 K + T)
R = 100 Ω, C = 1 nF.
To factor this in, the user can write the ∆T value to the
offset register. The ADT7468 then automatically adds it to
or subtracts it from the temperature measurement.
This filtering reduces both common-mode noise and
differential noise.
•
100Ω
1nF
100Ω
D–
04499-0-093
D+
REMOTE
TEMPERATURE
SENSOR
The ideality factor, nf, of the transistor is a measure of the
deviation of the thermal diode from ideal behavior. The
ADT7468 is trimmed for an nf value of 1.008. Use the
following equation to calculate the error introduced at a
temperature T (°C), when using a transistor whose nf does
not equal 1.008. See the processor data sheet for the nf
values.
Figure 24. Filter Between Remote Sensor and ADT7468
SERIES RESISTANCE CANCELLATION
Parasitic resistance to the ADT7468 D+ and D− inputs (seen in
series with the remote diode) is caused by a variety of factors,
including PCB track resistance and track length. This series
resistance appears as a temperature offset in the remote sensor’s
temperature measurement. This error typically causes a 0.5°C
offset per Ω of parasitic resistance in series with the remote
diode.
The ADT7468 automatically cancels out the effect of this series
resistance on the temperature reading, giving a more accurate
result, without the need for user characterization of this
resistance. The ADT7468 is designed to automatically cancel,
typically, up to 3 kΩ of resistance. By using an advanced
temperature measurement method, this is transparent to the
user. This feature allows resistances to be added to the sensor
path to produce a filter, allowing the part to be used in noisy
environments. See the Noise Filtering section for details.
Some CPU manufacturers specify the high and low current
levels of the substrate transistors. The high current level of
the ADT7468, IHIGH, is 96 µA and the low level current, ILOW,
is 6 µA. If the ADT7468 current levels do not match the
current levels specified by the CPU manufacturer, it might
be necessary to remove an offset. The CPUs data sheet
advises whether this offset needs to be removed and how to
calculate it. This offset can be programmed to the offset
register. It is important to note that, if more than one offset
must be considered, the algebraic sum of these offsets must
be programmed to the offset register.
If a discrete transistor is used with the ADT7468, the best
accuracy is obtained by choosing devices according to the
following criteria:
•
Base-emitter voltage greater than 0.25 V at 6 µA, at the
highest operating temperature.
•
Base-emitter voltage less than 0.95 V at 100 µA, at the
lowest operating temperature.
•
Base resistance less than 100 Ω.
•
Small variation in hFE (say 50 to 150) that indicates tight
control of VBE characteristics.
Rev. 0 | Page 19 of 80
ADT7468
Transistors, such as 2N3904, 2N3906, or equivalents in SOT-23
packages, are suitable devices to use.
Table 6. Temperature Data Format
Digital Output (10-Bit)1
1000 0000 00
1000 0011 00
1001 1100 00
1011 0101 00
1100 1110 00
1110 0111 00
1111 0110 00
0000 0000 00
0000 1010 01
0001 1001 10
0011 0010 11
0100 1011 00
0110 0100 00
0111 1101 00
0111 1111 00
Temperature
–128°C
–125°C
–100°C
–75°C
–50°C
–25°C
–10°C
0°C
10.25°C
25.5°C
50.75°C
75°C
100°C
125°C
127°C
1
Bold numbers denote 2 LSB of measurement in Extended Resolution
Register 2 (Reg. 0x77) with 0.25°C resolution.
Table 7. Extended Range, Temperature Data Format
Digital Output (10-Bit)1
0000 0000 00
0011 1111 00
0100 0000 00
0100 0001 00
0100 1010 00
0101 1001 00
0111 0010 00
1000 1001 00
1010 0100 00
1011 1101 00
1111 1111 00
Temperature
–64°C
–1°C
0°C
1°C
10°C
25°C
50°C
75°C
100°C
125°C
191°C
1
Bold numbers denote 2 LSB of measurement in Extended Resolution
Register 2 (Reg. 0x77) with 0.25°C resolution.
The ADT7468 has temperature offset registers at Addresses
0x70, 0x72 for the Remote 1 and Remote 2 temperature
channels. By doing a one-time calibration of the system, the
user can determine the offset caused by system board noise and
null it out using the offset registers. The offset registers
automatically add an Offset 64/twos complement 8-bit reading
to every temperature measurement. The LSBs add 0.5°C offset
to the temperature reading so the 8-bit register effectively allows
temperature offsets of up to ±64°C with a resolution of 0.5°C.
This ensures that the readings in the temperature measurement
registers are as accurate as possible.
Temperature Offset Registers
Reg. 0x70, Remote 1 Temperature Offset = 0x00 (0°C default)
Reg. 0x71, Local Temperature Offset = 0x00 (0°C default)
Reg. 0x72, Remote 2 Temperature Offset = 0x00 (0°C default)
ADT7463/ADT7468 Backwards Compatible Mode
By setting Bit 1 of Configuration Register 5 (0x7C), all temperature measurements are stored in the Zone Temp value registers
(0x25, 0x26, and 0x27) in twos complement in the range −64°C
to +127°C (the ADT7468 still makes calculations based on the
Offset 64 extended range and clamps the results, if necessary.)
The temperature limits must be reprogrammed in twos
complement. If a twos complement temperature below −63°C is
entered, the temperature is clamped to −63°C. In this mode, the
diode fault condition remains −128°C = 1000 0000, while in the
extended temperature range (−64°C to +191°C), the fault
condition is represented by −64°C = 0000 0000.
Temperature Measurement Registers
Reg. 0x26, Local Temperature
04499-0-013
D+
D–
As CPUs run faster, it is getting more difficult to avoid high
frequency clocks when routing the D+/D– traces around a
system board. Even when recommended layout guidelines are
followed, some temperature errors may still be attributable to
noise coupled onto the D+/D– lines. Constant high frequency
noise usually attenuates or increases temperature measurements
by a linear, constant value.
Reg. 0x25, Remote 1 Temperature
ADT7468
2N3904
NPN
Nulling Out Temperature Errors
Figure 25. Measuring Temperature Using an NPN Transistor
Reg. 0x27, Remote 2 Temperature
Reg. 0x77, Extended Resolution 2 = 0x00 default
<7:6> TDM2, Remote 2 temperature LSBs.
ADT7468
<5:4> LTMP, local temperature LSBs.
D+
D–
<3:2> TDM1, Remote 1 temperature LSBs.
04499-0-014
2N3906
PNP
Figure 26. Measuring Temperature Using a PNP Transistor
Rev. 0 | Page 20 of 80
ADT7468
Temperature Measurement Limit Registers
Table 9. Conversion Time with Averaging Enabled
Associated with each temperature measurement channel are
high and low limit registers. Exceeding the programmed high or
low limit causes the appropriate status bit to be set. Exceeding
either limit can also generate SMBALERT interrupts.
Channel
Voltage Channels
Remote Temperature
Local Temperature
Reg. 0x4E, Remote 1 Temperature Low Limit = 0x01 default
Single-Channel ADC Conversions
Reg. 0x4F, Remote 1 Temperature High Limit = 0x7F default
Setting Bit 6 of Configuration Register 2 (Reg. 0x73) places the
ADT7468 into single-channel ADC conversion mode. In this
mode, the ADT7468 can be made to read a single temperature
channel only. The appropriate ADC channel is selected by
writing to Bits <7:5> of the TACH1 minimum high byte register
(0x55).
Reg. 0x50, Local Temperature Low Limit = 0x01 default
Reg. 0x51, Local Temperature High Limit = 0x7F default
Reg. 0x52, Remote 2 Temperature Low Limit = 0x01 default
Reg. 0x53, Remote 2 Temperature High Limit = 0x7F default
Reading Temperature from the ADT7468
It is important to note that temperature can be read from the
ADT7468 as an 8-bit value (with 1°C resolution) or as a 10-bit
value (with 0.25°C resolution). If only 1°C resolution is
required, the temperature readings can be read back at any
time and in no particular order.
If the 10-bit measurement is required, this involves a 2-register
read for each measurement. The extended resolution register
(Reg. 0x77) should be read first. This causes all temperature
reading registers to be frozen until all temperature reading
registers have been read from. This prevents an MSB reading
from being updated while its two LSBs are being read and
vice versa.
ADDITIONAL ADC FUNCTIONS FOR
TEMPERATURE MEASUREMENT
A number of other functions are available on the ADT7468 to
offer the system designer increased flexibility.
Turn-Off Averaging
For each temperature measurement read from a value register,
16 readings have actually been made internally and the results
averaged before being placed into the value register. Sometimes
it is necessary to take a very fast measurement. Setting Bit 4 of
Configuration Register 2 (Reg. 0x73) turns averaging off.
Measurement Time
11 ms
39 ms
12 ms
Table 10. Channel Selection
Bits <7:5> Reg. 0x55
101
110
111
Channel Selected
Remote 1 temperature
Local temperature
Remote 2 temperature
Configuration Register 2 (Reg. 0x73)
<4> = 1, averaging off.
<6> = 1, single-channel convert mode.
TACH1 Minimum High Byte (Reg. 0x55)
<7:5> selects ADC channel for single-channel convert mode.
Overtemperature Events
Overtemperature events on any of the temperature channels can
be detected and dealt with automatically in automatic fan speed
control mode. Register 0x6A to Register 0x6C are the THERM
temperature limits. When a temperature exceeds its THERM
temperature limit, all PWM outputs run at the maximum PWM
duty cycle (Reg. 0x38, Reg. 0x39, and Reg. 0x3A). This
effectively runs the fans at the fastest allowed speed. The fans
stay running at this speed until the temperature drops below
THERM minus hysteresis. (This can be disabled by setting the
boost bit in Configuration Register 3, Bit 2, Reg. 0x78.) The
hysteresis value for that THERM temperature limit is the value
programmed into Reg. 0x6D and Reg. 0x6E (hysteresis
registers). The default hysteresis value is 4°C.
Table 8. Conversion Time with Averaging Disabled
Measurement Time
0.7 ms
7 ms
7 ms
1.3 ms
THERM LIMIT
HYSTERESIS (°C)
TEMPERATURE
FANS
100%
Figure 27. THERM Temperature Limit Operation
Rev. 0 | Page 21 of 80
04499-0-015
Channel
Voltage Channels
Remote Temperature 1
Remote Temperature 2
Local Temperature
ADT7468
LIMITS, STATUS REGISTERS, AND INTERRUPTS
LIMIT VALUES
THERM Limit Register
Associated with each measurement channel on the ADT7468
are high and low limits. These can form the basis of system
status monitoring; a status bit can be set for any out-of-limit
condition and detected by polling the device. Alternatively,
SMBALERT interrupts can be generated to flag a processor or
microcontroller of out-of-limit conditions.
8-Bit Limits
The following is a list of 8-bit limits on the ADT7468.
Reg. 0x7A, THERM Limit = 0x00 default
16-Bit Limits
The fan TACH measurements are 16-bit results. The fan TACH
limits are also 16 bits, consisting of a high byte and low byte.
Because fans running under speed or stalled are normally the
only conditions of interest, only high limits exist for fan TACHs.
Because the fan TACH period is actually being measured,
exceeding the limit indicates a slow or stalled fan.
Voltage Limit Registers
Fan Limit Registers
Reg. 0x44, 2.5 V Low Limit = 0x00 default
Reg. 0x54, TACH1 Minimum Low Byte = 0x00 default
Reg. 0x45, 2.5 V High Limit = 0xFF default
Reg. 0x55, TACH1 Minimum High Byte = 0x00 default
Reg. 0x46, VCCP Low Limit = 0x00 default
Reg. 0x56, TACH2 Minimum Low Byte = 0x00 default
Reg. 0x47, VCCP High Limit = 0xFF default
Reg. 0x57, TACH2 Minimum High Byte = 0x00 default
Reg. 0x48, VCC Low Limit = 0x00 default
Reg. 0x58, TACH3 Minimum Low Byte = 0x00 default
Reg. 0x49, VCC High Limit = 0xFF default
Reg. 0x59, TACH3 Minimum High Byte = 0x00 default
Reg. 0x4A, 5 V Low Limit = 0x00 default
Reg. 0x5A, TACH4 Minimum Low Byte = 0x00 default
Reg. 0x4B, 5 V High Limit = 0xFF default
Reg. 0x5B, TACH4 Minimum High Byte = 0x00 default
Out-of-Limit Comparisons
Reg. 0x4C, 12 V Low Limit = 0x00 default
Once all limits have been programmed, the ADT7468 can be
enabled for monitoring. The ADT7468 measures all voltage and
temperature measurements in round-robin format and sets the
appropriate status bit for out-of-limit conditions. TACH
measurements are not part of this round-robin cycle. Comparisons are done differently depending on whether the measured
value is being compared to a high or low limit.
Reg. 0x4D, 12 V High Limit = 0xFF default
Reg. 0x46, VCCP Low Limit = 0x00 default
Reg. 0x47, VCCP High Limit = 0xFF default
Reg. 0x48, VCC Low Limit = 0x00 default
Reg. 0x49, VCC High Limit = 0xFF default
High Limit: > Comparison Performed
Temperature Limit Registers
Low Limit: ≤ Comparison Performed
Reg. 0x4E, Remote 1 Temperature Low Limit = 0x01 default
Reg. 0x4F, Remote 1 Temperature High Limit = 0x7F default
Reg. 0x6A, Remote 1 THERM Limit = 0x64 default
Voltage and temperature channels use a window comparator for
error detecting and, therefore, have high and low limits. Fan
speed measurements use only a low limit. This fan limit is
needed only in manual fan control mode.
Analog Monitoring Cycle Time
Reg. 0x50, Local Temperature Low Limit = 0x01 default
Reg. 0x51, Local Temperature High Limit = 0x7F default
Reg. 0x6B, Local THERM Limit = 0x64 default
Reg. 0x52, Remote 2 Temperature Low Limit = 0x01 default
Reg. 0x53, Remote 2 Temperature High Limit = 0x7F default
The analog monitoring cycle begins when a 1 is written to the
start bit (Bit 0) of Configuration Register 1 (Reg. 0x40). By
default, the ADT7463 powers up with this bit set. The ADC
measures each analog input in turn and, as each measurement is
completed, the result is automatically stored in the appropriate
value register. This round-robin monitoring cycle continues
unless disabled by writing a 0 to Bit 0 of Configuration
Register 1.
Reg. 0x6C, Remote 2 THERM Limit = 0x64 default
Rev. 0 | Page 22 of 80
ADT7468
As the ADC is normally left to free-run in this manner, the time
taken to monitor all the analog inputs is normally not of
interest, because the most recently measured value of any input
can be read out at any time.
For applications where the monitoring cycle time is important,
it can easily be calculated.
Four dedicated supply voltage inputs
•
Supply voltage (VCC pin)
•
Local temperature
•
Two remote temperatures
Bit 7 (OOL) = 1, denotes a bit in Status Register 2 is set and
Status Register 2 should be read.
Bit 6 (R2T) = 1, Remote 2 temperature high or low limit has
been exceeded.
Bit 5 (LT) = 1, local temperature high or low limit has been
exceeded.
The total number of channels measured is
•
Status Register 1 (Reg. 0x41)
Bit 4 (R1T) = 1, Remote 1 temperature high or low limit has
been exceeded.
Bit 3 (5 V) = 1, 5 V high or low limit has been exceeded.
Bit 2 (VCC) = 1, VCC high or low limit has been exceeded.
As mentioned previously, the ADC performs round-robin
conversions and takes 11 ms for each voltage measurement,
12 ms for a local temperature reading, and 39 ms for each
remote temperature reading. The total monitoring cycle time
for averaged voltage and temperature monitoring is, therefore,
nominally
(5 × 11) + 12 + (2 × 39) = 145 ms
Bit 1 (VCCP) = 1, VCCP high or low limit has been exceeded.
Bit 0 (2.5 V) = 1, 2.5 V high or low limit has been exceeded.
Status Register 2 (Reg. 0x42)
Bit 7 (D2) = 1, indicates an open or short on D2+/D2– inputs.
Bit 6 (D1) = 1, indicates an open or short on D1+/D1– inputs.
Bit 5 (F4P) = 1, indicates Fan 4 has dropped below minimum
speed. Alternatively, indicates that the THERM limit has been
exceeded, if the THERM function is used.
Fan TACH measurements are made in parallel and are not
synchronized with the analog measurements in any way.
STATUS REGISTERS
The results of limit comparisons are stored in Status Registers 1
and 2. The status register bit for each channel reflects the status
of the last measurement and limit comparison on that channel.
If a measurement is within limits, the corresponding status
register bit is cleared to 0. If the measurement is out-of-limits,
the corresponding status register bit is set to 1.
The state of the various measurement channels can be polled by
reading the status registers over the serial bus. In Bit 7 (OOL) of
Status Register 1 (Reg. 0x41), 1 means that an out-of-limit event
has been flagged in Status Register 2. This means that the user
also needs to read Status Register 2. Alternatively, Pin 10 or Pin
14 can be configured as an SMBALERT output. This hard
interrupt automatically notifies the system supervisor of an outof-limit condition. Reading the status registers clears the
appropriate status bit as long as the error condition that caused
the interrupt has cleared. Status register bits are “sticky.”
Whenever a status bit is set, indicating an out-of-limit
condition, it remains set even if the event that caused it has
gone away (until read). The only way to clear the status bit is to
read the status register after the event has gone away. Interrupt
status mask registers (Reg. 0x74, and Reg. 0x75) allow individual
interrupt sources to be masked from causing an SMBALERT.
However, if one of these masked interrupt sources goes out-oflimit, its associated status bit is set in the interrupt status
registers.
Bit 4 (FAN3) = 1, indicates Fan 3 has dropped below minimum
speed.
Bit 3 (FAN2) = 1, indicates Fan 2 has dropped below minimum
speed.
Bit 2 (FAN1) = 1, indicates Fan 1 has dropped below minimum
speed.
Bit 1 (OVT) = 1, indicates a THERM overtemperature limit has
been exceeded.
Bit 0 (12V/VC) = 1, indicates a 12 V high or low limit has been
exceeded. If the VID code change function is used, this bit
indicates a change in VID code on the VID0 to VID5 inputs.
SMBALERT Interrupt Behavior
The ADT7468 can be polled for status, or an SMBALERT
interrupt can be generated for out-of-limit conditions. It is
important to note how the SMBALERT output and status bits
behave when writing interrupt handler software.
Rev. 0 | Page 23 of 80
ADT7468
HIGH LIMIT
HIGH LIMIT
TEMPERATURE
TEMPERATURE
CLEARED ON READ
(TEMP BELOW LIMIT)
“STICKY”
STATUS BIT
CLEARED ON READ
(TEMP BELOW LIMIT)
“STICKY”
STATUS BIT
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
SMBALERT
INTERRUPT
MASK BIT SET
INTERRUPT MASK BIT
CLEARED
(SMBALERT REARMED)
Figure 28. SMBALERT and Status Bit Behavior
Figure 28 shows how the SMBALERT output and “sticky” status
bits behave. Once a limit is exceeded, the corresponding status
bit is set to 1. The status bit remains set until the error condition
subsides and the status register is read. The status bits are
referred to as “sticky,” because they remain set until read by
software. This ensures that an out-of-limit event cannot be
missed, if software is polling the device periodically. Note that
the SMBALERT output remains low for the entire duration that
a reading is out-of-limit and until the status register has been
read. This has implications on how software handles the
interrupt.
04499-0-023
04499-0-022
SMBALERT
Figure 29. How Masking the Interrupt Source Affects SMBALERT Output
Interrupt Mask Register 1 (Reg. 0x74)
Bit 7 (OOL) = 1, masks SMBALERT for any alert condition
flagged in Status Register 2.
Bit 6 (R2T) = 1, masks SMBALERT for Remote 2 temperature.
Bit 5 (LT) = 1, masks SMBALERT for local temperature.
Bit 4 (R1T) = 1, masks SMBALERT for Remote 1 temperature.
Handling SMBALERT Interrupts
Bit 3 (5 V) = 1, masks SMBALERT for 5 V channel.
To prevent the system from being tied up servicing interrupts, it
is recommend to handle the SMBALERT interrupt as follows:
Bit 2 (VCC) = 1, masks SMBALERT for VCC channel.
Bit 0 (VCCP) = 1, masks SMBALERT for VCCP channel.
1.
Detect the SMBALERT assertion.
2.
Enter the interrupt handler.
3.
Read the status registers to identify the interrupt source.
4.
Mask the interrupt source by setting the appropriate mask
bit in the interrupt mask registers (Reg. 0x74 and
Reg. 0x75).
Interrupt Mask Register 2 (Reg. 0x75)
Bit 7 (D2) = 1, masks SMBALERT for Diode 2 errors.
Bit 6 (D1) = 1, masks SMBALERT for Diode 1 errors.
Bit 5 (FAN4) = 1, masks SMBALERT for Fan 4 failure.
5.
Take the appropriate action for a given interrupt source.
If the TACH4 pin is being used as the THERM input, this bit
masks SMBALERT for a THERM event.
6.
Exit the interrupt handler.
Bit 4 (FAN3) = 1, masks SMBALERT for Fan 3.
7.
Periodically poll the status registers. If the interrupt status
bit has cleared, reset the corresponding interrupt mask bit
to 0. This causes the SMBALERT output and status bits to
behave as shown in Figure 29.
Bit 3 (FAN2) = 1, masks SMBALERT for Fan 2.
Masking Interrupt Sources
Interrupt Mask Registers 1 and 2 are located at Addresses 0x74
and 0x75. These allow individual interrupt sources to be
masked out to prevent SMBALERT interrupts. Note that
masking an interrupt source prevents only the SMBALERT
output from being asserted; the appropriate status bit is set
normally.
Bit 2 (FAN1) = 1, masks SMBALERT for Fan 1.
Bit 1 (OVT) = 1, masks SMBALERT for overtemperature
(exceeding THERM temperature limits).
Bit 0 (12V/VC) = 1, masks SMBALERT for 12 V channel or for
a VID code change, depending on the function used.
Rev. 0 | Page 24 of 80
ADT7468
Enabling the SMBALERT Interrupt Output
The SMBALERT interrupt function is disabled by default.
Pin 10 or Pin 14 can be reconfigured as an SMBALERT output
to signal out-of-limit conditions.
Table 11. Configuring Pin 10 as SMBALERT Output
Register
Configuration Register 3
(Reg. 0x78)
below TMIN or if the duty cycle in manual mode is set to 0x00,
then pulling the THERM low externally has no effect. See
Figure 30 for more information.
TMIN
Bit Setting
<0> Pin 10 = ALERT
<1> Pin 10 = PWM2
THERM
Assigning THERM Functionality to a Pin
THERM ASSERTED TO LOW AS AN INPUT:
FANS DO NOT GO TO 100%, BECAUSE
TEMPERATURE IS BELOW TMIN
THERM ASSERTED TO LOW AS AN INPUT:
FANS DO NOT GO TO 100%, BECAUSE
TEMPERATURE IS ABOVE TMIN AND FANS
ARE ALREADY RUNNING
If THERM is enabled (Bit 1, Configuration Register 3 at
Address 0x78):
•
Pin 20 becomes THERM.
•
If Pin 14 is configured as THERM (Bit 0 and Bit 1 of
Configuration Register 4 at Address 0x7D), then THERM
is enabled on this pin.
Figure 30. Asserting THERM Low as an Input
in Automatic Fan Speed Control Mode
•
Pin 20 becomes a 5 V measurement input.
•
If Pin 14 is configured as THERM, then THERM is
disabled on this Pin.
The timer is started on the assertion of the ADT7468’s THERM
input and stopped when THERM is unasserted. The timer
counts THERM times cumulatively, that is, the timer resumes
counting on the next THERM assertion. The THERM timer
continues to accumulate THERM assertion times until the
timer is read (it is cleared on read) or until it reaches full scale.
If the counter reaches full scale, it stops at that reading until
cleared.
Table 12. Configuring Pin 14
Bit 1
0
1
0
1
THERM TIMER
The ADT7468 has an internal timer to measure THERM
assertion time. For example, the THERM input can be
connected to the PROCHOT output of a Pentium 4 CPU to
measure system performance. The THERM input can also be
connected to the output of a trip point temperature sensor.
If THERM is not enabled:
Bit 0
0
0
1
1
04499-0-024
Pin 14 on the ADT7468 has four possible functions:
SMBALERT, THERM, GPIO, and TACH4. The user chooses the
required functionality by setting Bit 0 and Bit 1 of Configuration Register 4 at Address 0x7D.
Function
TACH4
THERM
SMBALERT
GPIO
THERM as an Input
When THERM is configured as an input, the user can time
assertions on the THERM pin. This can be useful for connecting to the PROCHOT output of a CPU to gauge system
performance.
The user can also set up the ADT7468 so that, when the
THERM pin is driven low externally, the fans run at 100%. The
fans run at 100% for the duration of the time that the THERM
pin is pulled low. This is done by setting the BOOST bit (Bit 2)
in Configuration Register 3 (Address = 0x78) to 1. This works
only if the fan is already running, for example, in manual mode
when the current duty cycle is above 0x00, or in automatic
mode when the temperature is above TMIN. If the temperature is
The 8-bit THERM timer register (Reg. 0x79) is designed such
that Bit 0 is set to 1 on the first THERM assertion. Once the
cumulative THERM assertion time has exceeded 45.52 ms, Bit 1
of the THERM timer is set and Bit 0 now becomes the LSB of
the timer with a resolution of 22.76 ms (see Figure 31).
When using the THERM timer, be aware of the following.
After a THERM timer read (Reg. 0x79):
1.
The contents of the timer are cleared on read.
2.
The F4P bit (Bit 5) of Status Register 2 needs to be cleared
(assuming that the THERM timer limit has been
exceeded).
Rev. 0 | Page 25 of 80
ADT7468
THERM
If the THERM timer is read during a THERM assertion, then
the following happens:
THERM
TIMER
(REG. 0x79)
1.
The contents of the timer are cleared.
2.
Bit 0 of the THERM timer is set to 1 (because a THERM
assertion is occurring).
3.
The THERM timer increments from zero.
4.
If the THERM timer limit (Reg. 0x7A) = 0x00, then the
F4P bit is set.
THERM ASSERTED
≤ 22.76ms
THERM
ACCUMULATE THERM LOW
ASSERTION TIMES
THERM
TIMER
(REG. 0x79)
Generating SMBALERT Interrupts from THERM Timer Events
The ADT7468 can generate SMBALERTs when a programmable THERM timer limit has been exceeded. This allows the
system designer to ignore brief, infrequent THERM assertions,
while capturing longer THERM timer events. Register 0x7A is
the THERM timer limit register. This 8-bit register allows a
limit from 0 s (first THERM assertion) to 5.825 s to be set
before an SMBALERT is generated. The THERM timer value is
compared with the contents of the THERM timer limit register.
If the THERM timer value exceeds the THERM timer limit
value, then the F4P bit (Bit 5) of Status Register 2 is set and an
SMBALERT is generated. Note that the F4P bit (Bit 5) of Mask
Register 2 (Reg. 0x75) masks out SMBALERTs, if this bit is set
to 1; although the F4P bit of Interrupt Status Register 2 still is
set, if the THERM timer limit is exceeded.
0 0 0 0 0 0 1 0
7 6 5 4 3 2 1 0
THERM ASSERTED
≥ 45.52ms
THERM
THERM
TIMER
(REG. 0x79)
0 0 0 0 0 1 0 1
7 6 5 4 3 2 1 0 THERM ASSERTED ≥ 113.8ms
(91.04ms + 22.76ms)
Figure 31.Understanding the THERM Timer
Figure 32 is a functional block diagram of the THERM timer,
limit, and associated circuitry. Writing a value of 0x00 to the
THERM timer limit register (Reg. 0x7A) causes SMBALERT to
be generated on the first THERM assertion. A THERM timer
limit value of 0x01 generates an SMBALERT, once cumulative
THERM assertions exceed 45.52 ms.
2.914s
1.457s
728.32ms
364.16ms
182.08ms
91.04ms
45.52ms
22.76ms
2.914s
1.457s
728.32ms
364.16ms THERM TIMER
(REG. 0x79)
182.08ms
91.04ms
45.52ms
22.76ms
0 1 2 3 4 5 6 7
04499-0-025
ACCUMULATE THERM LOW
ASSERTION TIMES
7 6 5 4 3 2 1 0
THERM
THERM TIMER CLEARED ON READ
COMPARATOR
IN
OUT
F4P BIT (BIT 5)
STATUS REGISTER 2
SMBALERT
LATCH
RESET
CLEARED
ON READ
1 = MASK
F4P BIT (BIT 5)
MASK REGISTER 2
(REG. 0x75)
Figure 32. Functional Block Diagram of THERM Monitoring Circuitry
Rev. 0 | Page 26 of 80
04499-0-026
THERM LIMIT
(REG. 0x7A)
0 0 0 0 0 0 0 1
7 6 5 4 3 2 1 0
ADT7468
Configuring the Relevant THERM Behavior
Configure the desired pin as the THERM timer input.
Setting Bit 1 (THERM timer enable) of Configuration
Register 3 (Reg. 0x78) enables the THERM timer
monitoring functionality. This is disabled on Pins 14 and
20 by default.
Setting Bits 0 and 1 (PIN14FUNC) of Configuration
Register 4 (Reg. 0x7D) enables THERM timer output
functionality on Pin 20 (Bit 1 of Configuration Register 3,
THERM, must also be set). Pin 14 can also be used as
TACH4.
2.
Select the desired fan behavior for THERM timer events.
Assuming that the fans are running, setting Bit 2 (BOOST
bit) of Configuration Register 3 (Reg. 0x78) causes all fans
to run at 100% duty cycle whenever THERM is asserted.
This allows fail-safe system cooling. If this bit is 0, the fans
run at their current settings and are not affected by
THERM events. If the fans are not already running when
THERM is asserted, the fans do not run to full speed.
3.
Select whether THERM timer events should generate
SMBALERT interrupts.
Bit 5 (F4P) of Mask Register 2 (Reg. 0x75), when set, masks
out SMBALERTs when the THERM timer limit value is
exceeded. This bit should be cleared, if SMBALERTs based
on THERM events are required.
4.
Select a suitable THERM limit value.
In addition to monitoring THERM as an input, the ADT7468
can optionally drive THERM low as an output. In cases where
PROCHOT is bidirectional, THERM can be used to throttle the
processor by asserting PROCHOT. The user can preprogram
system-critical thermal limits. If the temperature exceeds a
thermal limit by 0.25°C, THERM asserts low. If the temperature
is still above the thermal limit on the next monitoring cycle,
THERM stays low. THERM remains asserted low until the
temperature is equal to or below the thermal limit. Because the
temperature for that channel is measured only once for every
monitoring cycle, after THERM asserts it is guaranteed to
remain low for at least one monitoring cycle.
The THERM pin can be configured to assert low, if the
Remote 1, local, or Remote 2 THERM temperature limits are
exceeded by 0.25°C. The THERM temperature limit registers
are at Registers 0x6A, 0x6B, and 0x6C, respectively. Setting Bit 3
of Registers 0x5F, 0x60, and 0x61 enables the THERM output
feature for the Remote 1, local, and Remote 2 temperature
channels, respectively. Figure 33 shows how the THERM pin
asserts low as an output in the event of a critical
overtemperature.
THERM LIMIT
+0.25°C
THERM LIMIT
This value determines whether an SMBALERT is generated
on the first THERM assertion, or only if a cumulative
THERM assertion time limit is exceeded. A value of 0x00
causes an SMBALERT to be generated on the first THERM
assertion.
5.
Configuring the THERM Pin as an Output
TEMP
THERM
Select a THERM monitoring time.
This value specifies how often OS or BIOS level software
checks the THERM timer. For example, BIOS could read
the THERM timer once an hour to determine the cumulative THERM assertion time. If, for example, the total
THERM assertion time is <22.76 ms in Hour 1, >182.08 ms
in Hour 2, and >5.825 s in Hour 3, this can indicate that
system performance is degrading significantly, because
THERM is asserting more frequently on an hourly basis.
ADT7468
MONITORING
CYCLE
04499-0-027
1.
can be calculated for a fixed THERM timer limit time. For
example, if it takes one week for a THERM timer limit of
2.914 s to be exceeded and the next time it takes only 1
hour, then this is an indication of a serious degradation in
system performance.
Figure 33. Asserting THERM as an Output, Based on Tripping THERM Limits
An alternative method of disabling THERM is to program the
THERM temperature limit to –64°C or less in Offset 64 mode,
or −128°C or less in twos complement mode; that is, for
THERM temperature limit values less than –63°C or –128°C,
respectively, THERM is disabled.
Alternatively, OS or BIOS level software can timestamp
when the system is powered on. If an SMBALERT is
generated due to the THERM timer limit being exceeded,
another timestamp can be taken. The difference in time
Rev. 0 | Page 27 of 80
ADT7468
The ADT7468 uses pulse-width modulation (PWM) to control
fan speed. This relies on varying the duty cycle (or on/off ratio)
of a square wave applied to the fan to vary the fan speed. The
external circuitry required to drive a fan using PWM control is
extremely simple. For 4-wire fans, the PWM drive might need
only a pull-up resistor. In many cases, the 4-wire fan PWM
input has a built-in pull-up resistor.
The ADT7468 PWM frequency can be set to a selection of low
frequencies or a single high PWM frequency. The low frequency
options are usually used for 2-wire and 3-wire fans, while the
high frequency option is usually used with 4-wire fans.
For 2-wire or 3-wire fans, a single N-channel MOSFET is the
only drive device required. The specifications of the MOSFET
depend on the maximum current required by the fan being
driven and the input capacitance of the FET. Because a 10 kΩ
(or greater) resistor must be used as a PWM pull-up, an FET
with large input capacitance can cause the PWM output to
become distorted and adversely affect the fan control range.
This is a requirement only when using high frequency PWM
mode.
Typical notebook fans draw a nominal 170 mA, and so SOT
devices can be used where board space is a concern. In desktops,
fans can typically draw 250 mA to 300 mA each. If you drive
several fans in parallel from a single PWM output or drive
larger server fans, the MOSFET must handle the higher current
requirements. The only other stipulation is that the MOSFET
should have a gate voltage drive, VGS < 3.3 V, for direct
interfacing to the PWM_OUT pin. VGS can be greater than
3.3 V as long as the pull-up on the gate is tied to 5 V. The
MOSFET should also have a low on resistance to ensure that
there is not significant voltage drop across the FET, which
would reduce the voltage applied across the fan and, therefore,
the maximum operating speed of the fan.
Figure 34 uses a 10 kΩ pull-up resistor for the TACH signal.
This assumes that the TACH signal is an open-collector from
the fan. In all cases, the TACH signal from the fan must be kept
below 5 V maximum to prevent damaging the ADT7468. If in
doubt as to whether the fan used has an open-collector or
totem-pole TACH output, use one of the input signal
conditioning circuits shown in the Fan Speed Measurement
section.
Figure 35 shows a fan drive circuit using an NPN transistor
such as a general-purpose MMBT2222. While these devices are
inexpensive, they tend to have much lower current handling
capabilities and higher on resistance than MOSFETs. When
choosing a transistor, care should be taken to ensure that it
meets the fan’s current requirements. Ensure that the base
resistor is chosen such that the transistor is saturated when the
fan is powered on.
Because 4-wire fans are powered continuously, the fan speed is
not switched on or off as with previous PWM driven/powered
fans. This enables it to perform better than 3-wire fans,
especially for high frequency applications.
12V
12V
10kΩ
10kΩ
TACH
TACH
4.7kΩ
3.3V
12V
FAN
1N4148
ADT7468
665Ω
Q1
MMBT2222
PWM
04499-0-029
FAN DRIVE USING PWM CONTROL
Figure 35. Driving a 3-Wire Fan Using an NPN Transistor
Figure 36 shows a typical drive circuit for 4-wire fans.
12V 12V
Figure 34 shows how to drive a 3-wire fan using PWM control.
12V, 4-WIRE FAN
12V
10kΩ
TACH/AIN
10kΩ
TACH/AIN
10kΩ
12V
FAN
4.7kΩ
3.3V
1N4148
TACH
TACH
PWM
ADT7468
4.7kΩ
3.3V
2kΩ
ADT7468
PWM
Q1
NDT3055L
04499-0-028
10kΩ
PWM
VCC
10kΩ
Figure 36. Driving a 4-Wire Fan
Figure 34. Driving a 3-Wire Fan Using an N-Channel MOSFET
Rev. 0 | Page 28 of 80
04499-0-041
12V
ADT7468
Driving Two Fans from PWM3
Driving up to Three Fans from PWM3
The ADT7468 has four TACH inputs available for fan speed
measurement, but only three PWM drive outputs. If a fourth fan
is being used in the system, it should be driven from the PWM3
output in parallel with the third fan. Figure 37 shows how to
drive two fans in parallel using low cost NPN transistors.
Figure 38 shows the equivalent circuit using a MOSFET.
TACH measurements for fans are synchronized to particular
PWM channels; for example, TACH1 is synchronized to
PWM1. TACH3 and TACH4 are both synchronized to PWM3,
so PWM3 can drive two fans. Alternatively, PWM3 can be programmed to synchronize TACH2, TACH3, and TACH4 to the
PWM3 output. This allows PWM3 to drive two or three fans. In
this case, the drive circuitry looks the same, as shown in
Figure 37 and Figure 38. The SYNC bit in Register 0x62 enables
this function.
Because the MOSFET can handle up to 3.5 A, it is simply a
matter of connecting another fan directly in parallel with the
first. Care should be taken in designing drive circuits with
transistors and FETs to ensure that the PWM pins are not
required to source current and that they sink less than the
5 mA maximum current specified on the data sheet.
Synchronization is not required in high frequency mode when
used with 4-wire fans.
<4> (SYNC) Enhance Acoustics Register 1 (Reg. 0x62)
SYNC = 1, synchronizes TACH2, TACH3, and TACH4 to
PWM3.
12V
3.3V
3.3V
1N4148
ADT7468
TACH3
1kΩ
PWM3
TACH4
Q1
MMBT3904
2.2kΩ
10Ω
Q2
MMBT2222
04499-0-030
10Ω
Q3
MMBT2222
Figure 37. Interfacing Two Fans in Parallel to the PWM3 Output Using Low Cost NPN Transistors
3.3V
10kΩ
TYPICAL
TACH4
+V
3.3V
ADT7468
+V
10kΩ
TYPICAL
TACH3
3.3V
TACH
5V OR
12V FAN
1N4148
TACH
5V OR
12V FAN
PWM3
Q1
NDT3055L
04499-0-031
10kΩ
TYPICAL
Figure 38. Interfacing Two Fans in Parallel to the PWM3 Output Using a Single N-Channel MOSFET
Rev. 0 | Page 29 of 80
ADT7468
Driving 2-Wire Fans
The ADT7468 can support 2-wire fans only when low frequency PWM mode is selected in Configuration Register 5,
Bit 2. If this bit is not set to 1, the ADT7468 cannot measure the
speed of 2-wire fans.
Figure 39 shows how a 2-wire fan can be connected to the
ADT7468. This circuit allows the speed of a 2-wire fan to be
measured, even though the fan has no dedicated TACH signal.
A series resistor, RSENSE, in the fan circuit converts the fan
commutation pulses into a voltage, which is ac-coupled into the
ADT7468 through the 0.01 µF capacitor. On-chip signal
conditioning allows accurate monitoring of fan speed. The
value of RSENSE chosen depends upon the programmed input
threshold and the current drawn by the fan. For fans drawing
approximately 200 mA, a 2 Ω RSENSE value is suitable when the
threshold is programmed as 40 mV.
For fans that draw more current, such as larger desktop or
server fans, RSENSE can be reduced for the same programmed
threshold. The smaller the threshold programmed the better,
because more voltage is developed across the fan and the fan
spins faster. Note that when the voltage spikes (either negative
going or positive going) are more than 40 mV in amplitude, the
fan speed can be reliably determined.
LAYING OUT 2-WIRE AND 3-WIRE FANS
Figure 41 shows how to lay out a common circuit arrangement
for 2-wire and 3-wire fans. Some components are not populated,
depending on whether a 2-wire or 3-wire fan is used.
12V OR 5V
R1
1N4148
3.3V OR 5V
R2
R5
+V
PWM
ADT7468
3.3V
TACH
1N4148
5V OR
12V FAN
R3
10kΩ
TYPICAL
Q1
NDT3055L
PWM
R4
FOR 3-WIRE FANS:
POPULATE R1, R2, R3
R4 = 0W
C1 = UNPOPULATED
FOR 2-WIRE FANS:
POPULATE R4, C1
R1, R2, R3 UNPOPULATED
Figure 41. Planning for 2-Wire or 3-Wire Fans on a PCB
0.01µF
RSENSE
2Ω
TYPICAL
TACH Inputs
04499-0-032
TACH
Q1
MMBT2222
04499-0-042
C1
Pins 9, 11, 12, and 14 (when configured as TACH inputs) are
open-drain TACH inputs intended for fan speed measurement.
Figure 39. Driving a 2-Wire Fan
Figure 40 shows a typical plot of the sensing waveform at the
TACH/AIN pin.
Signal conditioning in the ADT7468 accommodates the slow
rise and fall times typical of fan tachometer outputs. The
maximum input signal range is 0 V to 5 V, even when VCC is less
than 5 V. In the event that these inputs are supplied from fan
outputs that exceed 0 V to 5 V, either resistive attenuation of the
fan signal or diode clamping must be included to keep inputs
within an acceptable range.
Figure 42 to Figure 45 show circuits for most common fan
TACH outputs.
If the fan TACH output has a resistive pull-up to VCC, it can be
connected directly to the fan input, as shown in Figure 42.
VCC
12V
TACH
OUTPUT
TACH
FAN SPEED
COUNTER
04499-0-033
ADT7468
Figure 40. Fan Speed Sensing Waveform at TACH/AIN Pin
Rev. 0 | Page 30 of 80
Figure 42. Fan with TACH Pull-Up to VCC
04499-0-034
PULL-UP
4.7kΩ
TYPICAL
ADT7468
If the fan output has a resistive pull-up to 12 V (or other voltage
greater than 5 V) then the fan output can be clamped with a
Zener diode, as shown in Figure 43. The Zener diode voltage
should be chosen so that it is greater than VIH of the TACH
input but less than 5 V, allowing for the voltage tolerance of the
Zener. A value of between 3 V and 5 V is suitable.
VCC
PULL-UP
4.7kΩ
TYPICAL
TACH
OUTPUT
TACH
ZD1*
FAN SPEED
COUNTER
ADT7468
04499-0-035
12V
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 × VCC
Fan Speed Measurement
The fan counter does not count the fan TACH output pulses
directly, because the fan speed could be less than 1,000 RPM
and it would take several seconds to accumulate a reasonably
large and accurate count. Instead, the period of the fan
revolution is measured by gating an on-chip 90 kHz oscillator
into the input of a 16-bit counter for N periods of the fan TACH
output (Figure 46), so the accumulated count is actually
proportional to the fan tachometer period and inversely
proportional to the fan speed.
N, the number of pulses counted, is determined by the settings
of Register 0x7B (TACH pulses per revolution register). This
register contains two bits for each fan, allowing one, two
(default), three, or four TACH pulses to be counted.
Figure 43. Fan with TACH Pull-Up to Voltage > 5 V, for example, 12 V)
Clamped with Zener Diode
CLOCK
If the fan has a strong pull-up (less than 1 kΩ) to 12 V or a
totem-pole output, then a series resistor can be added to limit
the Zener current, as shown in Figure 44.
PWM
VCC
5V OR 12V
FAN
TACH
TACH
OUTPUT
2
TACH
ZD1
ZENER*
04499-0-038
R1
10kΩ
3
FAN SPEED
COUNTER
4
ADT7468
04499-0-036
PULL-UP TYP
<1kΩ OR
TOTEM POLE
1
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 × VCC
Figure 44. Fan with Strong TACH Pull-Up to > VCC or Totem-Pole Output,
Clamped with Zener and Resistor
Figure 46. Fan Speed Measurement
Fan Speed Measurement Registers
The fan tachometer readings are 16-bit values consisting of a
2-byte read from the ADT7468.
Alternatively, a resistive attenuator can be used, as shown in
Figure 45. R1 and R2 should be chosen such that
Reg. 0x28, TACH1 Low Byte = 0x00 default
2 V < VPULL-UP × R2/(RPULL-UP + R1 + R2) < 5 V
The fan inputs have an input resistance of nominally 160 kΩ to
ground, which should be taken into account when calculating
resistor values.
Reg. 0x29, TACH1 High Byte = 0x00 default
Reg. 0x2A, TACH2 Low Byte = 0x00 default
Reg. 0x2B, TACH2 High Byte = 0x00 default
With a pull-up voltage of 12 V and pull-up resistor less than
1 kΩ, suitable values for R1 and R2 would be 100 kΩ and 47 kΩ,
respectively. This gives a high input voltage of 3.83 V.
Reg. 0x2C, TACH3 Low Byte = 0x00 default
Reg. 0x2D, TACH3 High Byte = 0x00 default
VCC
12V
Reg. 0x2E, TACH4 Low Byte = 0x00 default
Reg. 0x2F, TACH4 High Byte = 0x00 default
<1kΩ
TACH
R2*
FAN SPEED
COUNTER
ADT7468
04499-0-037
R1*
TACH
OUTPUT
*SEE TEXT
Figure 45. Fan with Strong TACH Pull-Up to > VCC or Totem-Pole Output,
Attenuated with R1/R2
Reading Fan Speed from the ADT7468
The measurement of fan speeds involves a 2-register read for
each measurement. The low byte should be read first. This
causes the high byte to be frozen until both high and low byte
registers have been read, preventing erroneous TACH readings.
The fan tachometer reading registers report back the number of
Rev. 0 | Page 31 of 80
ADT7468
11.11 µs period clocks (90 kHz oscillator) gated to the fan speed
counter, from the rising edge of the first fan TACH pulse to the
rising edge of the third fan TACH pulse (assuming two pulses
per revolution are being counted). Because the device is
essentially measuring the fan TACH period, the higher the
count value, the slower the fan is actually running. A 16-bit fan
tachometer reading of 0xFFFF indicates either that the fan has
stalled or is running very slowly (<100 RPM).
Calculating Fan Speed
Assuming a fan with a two pulses per revolution (and two
pulses per revolution being measured), fan speed is calculated
by
Fan Speed (RPM) = (90,000 × 60)/Fan TACH Reading
where Fan TACH Reading is the 16-bit fan tachometer reading.
Example:
High Limit: > Comparison Performed
TACH1 High Byte (Reg. 0x29) = 0x17
Because the actual fan TACH period is being measured, falling
below a fan TACH limit by 1 sets the appropriate status bit and
can be used to generate an SMBALERT.
TACH1 Low Byte (Reg. 0x28) = 0xFF
What is Fan 1 speed in RPM?
Fan TACH Limit Registers
Fan 1 TACH Reading = 0x17FF = 6143 (decimal)
The fan TACH limit registers are 16-bit values consisting of two
bytes.
RPM = (f × 60)/Fan 1 TACH Reading
Reg. 0x54, TACH1 Minimum Low Byte = 0xFF default
RPM = (90000 × 60)/6143
Reg. 0x55, TACH1 Minimum High Byte = 0xFF default
Fan Speed = 879 RPM
Reg. 0x56, TACH2 Minimum Low Byte = 0xFF default
Fan Pulses per Revolution
Reg. 0x57, TACH2 Minimum High Byte = 0xFF default
Different fan models can output either 1, 2, 3, or 4 TACH pulses
per revolution. Once the number of fan TACH pulses has been
determined, it can be programmed into the fan pulses per
revolution register (Reg. 0x7B) for each fan. Alternatively, this
register can be used to determine the number or pulses per
revolution output by a given fan. By plotting fan speed measurements at 100% speed with different pulses per revolution
setting, the smoothest graph with the lowest ripple determines
the correct pulses per revolution value.
Reg. 0x58, TACH3 Minimum Low Byte = 0xFF default
Reg. 0x59, TACH3 Minimum High Byte = 0xFF default
Reg. 0x5A, TACH4 Minimum Low Byte = 0xFF default
Reg. 0x5B, TACH4 Minimum High Byte = 0xFF default
Fan Speed Measurement Rate
The fan TACH readings are normally updated once every
second.
Fan Pulses per Revolution Register
The FAST bit (Bit 3) of Configuration Register 3 (Reg. 0x78),
when set, updates the fan TACH readings every 250 ms.
<3:2> Fan 2 default = 2 pulses per revolution.
<1:0> Fan 1 default = 2 pulses per revolution.
<5:4> Fan 3 default = 2 pulses per revolution.
If any of the fans are not being driven by a PWM channel but
are powered directly from 5 V or 12 V, their associated dc bit in
Configuration Register 3 should be set. This allows TACH
readings to be taken on a continuous basis for fans connected
directly to a dc source. For optimal results, the associated dc bit
should always be set when using 4-wire fans.
<7:6> Fan 4 default = 2 pulses per revolution.
00 = 1 pulse per revolution.
01 = 2 pulses per revolution.
10 = 3 pulses per revolution.
11 = 4 pulses per revolution.
Rev. 0 | Page 32 of 80
ADT7468
2-Wire Fan Speed Measurements (Low Frequency Mode
Only)
The ADT7468 is capable of measuring the speed of 2-wire fans,
that is, fans without TACH outputs. To do this, the fan must be
interfaced as shown in the Driving 2-Wire Fans section. In this
case, the TACH inputs should be reprogrammed as analog
inputs, AIN.
Using Configuration Register 4 (0x40) Bit 5 (FSPDIS), this
functionality can be changed (see the Disabling Fan Startup
Timeout section).
PWM1 Configuration (Reg. 0x5C)
<2:0> SPIN, startup timeout for PWM1.
000 = No startup timeout
Configuration Register 2 (Reg. 0x73)
001 = 100 ms
Bit 3 (AIN4) = 1, Pin 14 is reconfigured to measure the speed
of a 2-wire fan using an external sensing resistor and coupling
capacitor.
010 = 250 ms default
Bit 2 (AIN3) = 1, Pin 9 is reconfigured to measure the speed of
a 2-wire fan using an external sensing resistor and coupling
capacitor.
101 = 1 s
Bit 1 (AIN2) = 1, Pin 12 is reconfigured to measure the speed
of a 2-wire fan using an external sensing resistor and coupling
capacitor.
011 = 400 ms
100 = 667 ms
110 = 2 s
111 = 4 s
PWM2 Configuration (Reg. 0x5D)
<2:0> SPIN, startup timeout for PWM2.
000 = No startup timeout
Bit 0 (AIN1) = 1, Pin 11 is reconfigured to measure the speed
of a 2-wire fan using an external sensing resistor and coupling
capacitor.
001 = 100 ms
010 = 250 ms default
AIN Switching Threshold
011 = 400 ms
Having configured the TACH inputs as AIN inputs for 2-wire
measurements, a user can select the sensing threshold for the
AIN signal.
100 = 667 ms
Configuration Register 4 (Reg. 0x7D)
110 = 2 s
101 = 1 s
111 = 4 s
PWM3 Configuration (Reg. 0x5E)
<3:2> AINL, input threshold for 2-wire fan speed
measurements.
<2:0> SPIN, start-up timeout for PWM3.
00 = ±20 mV
01 = ±40 mV
000 = No startup timeout
10 = ±80 mV
001 = 100 ms
11 = ±130 mV
Fan Spin-Up
010 = 250 ms default
The ADT7468 has a unique fan spin-up function. It spins the
fan at 100% PWM duty cycle until two TACH pulses are
detected on the TACH input. Once two TACH pulses have been
detected, the PWM duty cycle goes to the expected running
value, for example, 33%. The advantage is that fans have
different spin-up characteristics and take different times to
overcome inertia. The ADT7468 runs the fans just fast enough
to overcome inertia and is quieter on spin-up than fans
programmed to spin up for a given spin-up time.
100 = 667 ms
011 = 400 ms
Fan Startup Timeout
To prevent the generation of false interrupts as a fan spins up
(because it is below running speed), the ADT7468 includes a
fan startup timeout function. During this time, the ADT7468
looks for two TACH pulses. If two TACH pulses are not
detected, then an interrupt is generated.
101 = 1 s
110 = 2 s
111 = 4 s
Disabling Fan Startup Timeout
Although fan startup makes fan spin-ups much quieter than
fixed-time spin-ups, the option exists to use fixed spin-up times.
Setting Bit 5 (FSPDIS) to 1 in Configuration Register 1
(Reg. 0x40) disables the spin-up for two TACH pulses. Instead,
the fan spins up for the fixed time as selected in Reg. 0x5C to
Reg. 0x5E.
Rev. 0 | Page 33 of 80
ADT7468
PWM Logic State
In manual fan speed control mode, the ADT7468 allows the
duty cycle of any PWM output to be manually adjusted. This
can be useful, if the user wants to change fan speed in software
or adjust PWM duty cycle output for test purposes. Bits <7:5>
of Reg. 0x5C to Reg. 0x5E (PWM Configuration) control the
behavior of each PWM output.
The PWM outputs can be programmed high for 100% duty
cycle (noninverted) or low for 100% duty cycle (inverted).
PWM1 Configuration (Reg. 0x5C)
<4> INV.
0 = Logic high for 100% PWM duty cycle.
1 = Logic low for 100% PWM duty cycle.
PWM Configuration Register (Reg. 0x5C to Reg. 0x5E)
PWM2 Configuration (Reg. 0x5D)
<7:5> BHVR.
<4> INV.
0 = Logic high for 100% PWM duty cycle.
1 = Logic low for 100% PWM duty cycle.
111 = manual mode
Once under manual control, each PWM output can be manually
updated by writing to Reg. 0x30 to Reg. 0x32 (PWMx current
duty cycle registers).
PWM3 Configuration (Reg. 0x5E)
<4> INV.
0 = Logic high for 100% PWM duty cycle.
1 = Logic low for 100% PWM duty cycle.
Programming the PWM Current Duty Cycle Registers
Low Frequency Mode PWM Drive Frequency
The PWM drive frequency can be adjusted for the application.
Register 0x5F to Register 0x61 configure the PWM frequency
for PWM1 to PWM3, respectively. In high frequency mode, the
PWM drive frequency is always 22.5 kHz and cannot be
changed.
The PWM current duty cycle registers are 8-bit registers that
allow the PWM duty cycle for each output to be set anywhere
from 0% to 100% in steps of 0.39%. The value to be programmed into the PWMMIN register is given by
Value (decimal) = PWMMIN/0.39
Example 1: For a PWM duty cycle of 50%,
Value (decimal) = 50/0.39 = 128 (decimal)
Value = 128 (decimal) or 0x80 (hex)
PWM1 Frequency Registers (Reg. 0x5F to Reg. 0x61)
<2:0> FREQ.
000 = 11.0 Hz
Example 2: For a PWM duty cycle of 33%,
001 = 14.7 Hz
Value (decimal) = 33/0.39 = 85 (decimal)
Value = 85 (decimal) or 0x54 (hex)
010 = 22.1 Hz
011 = 29.4 Hz
PWM Duty Cycle Registers
100 = 35.3 Hz default
Reg. 0x30 PWM1 Duty Cycle = 0x00 (0% default)
101 = 44.1 Hz
Reg. 0x31 PWM2 Duty Cycle = 0x00 (0% default)
110 = 58.8 Hz
Reg. 0x32 PWM3 Duty Cycle = 0x00 (0% default)
111 = 88.2 Hz
Fan Speed Control
The ADT7468 controls fan speed using two modes: automatic
and manual.
In automatic fan speed control mode, fan speed is automatically
varied with temperature and without CPU intervention, once
initial parameters are set up. The advantage is that, if the system
hangs, the user is guaranteed that the system is protected from
overheating. The automatic fan speed control incorporates a
feature called dynamic TMIN calibration. This feature reduces the
design effort required to program the automatic fan speed
control loop. See the Programming the Automatic Fan Speed
Control Loop section.
By reading the PWMx current duty cycle registers, the user can
keep track of the current duty cycle on each PWM output, even
when the fans are running in automatic fan speed control mode
or acoustic enhancement mode. See the Programming the
Automatic Fan Speed Control Loop section for details.
OPERATING FROM 3.3 V STANDBY
The ADT7468 has been specifically designed to operate from a
3.3 V STBY supply. In computers that support S3 and S5 states,
the core voltage of the processor is lowered in these states. If
using the dynamic TMIN mode, lowering the core voltage of the
processor changes the CPU temperature and changes the
dynamics of the system under dynamic TMIN control. Likewise,
when monitoring THERM, the THERM timer should be
disabled during these states.
Rev. 0 | Page 34 of 80
ADT7468
Dynamic TMIN Control Register 1 (Reg. 0x36)
<1> VCCPLO = 1
POWER-ON DEFAULT
When the ADT7468 is powered up, it polls the VCCP input.
When the power is supplied from 3.3 V STBY and the VCCP
voltage drops below the VCCP low limit, the following occurs:
If VCCP stays below 0.75 V (the system CPU power rail is not
powered up), then the ADT7468 assumes the functionality of
the default registers after the ADT7468 is addressed via any
valid SMBus transaction.
1.
Status Bit 1 (VCCP) in Status Register 1 is set.
2.
SMBALERT is generated, if enabled.
3.
THERM monitoring is disabled. The THERM timer should
hold its value prior to the S3 or S5 state.
4.
Dynamic TMIN control is disabled. This prevents TMIN from
being adjusted due to an S3 or S5 state.
5.
The ADT7468 is prevented from entering the shutdown
state.
Once the core voltage, VCCP, goes above the VCCP low limit,
everything is re-enabled and the system resumes normal
operation.
XNOR TREE TEST MODE
The ADT7468 includes an XNOR tree test mode. This mode is
useful for in-circuit test equipment at board-level testing. By
applying stimulus to the pins included in the XNOR tree, it is
possible to detect opens or shorts on the system board.
The XNOR tree test is invoked by setting Bit 0 (XEN) of the
XNOR tree test enable register (Reg. 0x6F).
If VCCP goes high (the system processor power rail is powered
up), then a fail-safe timer begins to count down. If the ADT7468
is not addressed by any valid SMBus transaction before the failsafe timeout (4.6 s) lapses, then the ADT7468 drives the fans to
full speed. If the ADT7468 is addressed by a valid SMBus
transaction after this point, the fans stop, and the ADT7468
assumes its default settings and begins normal operation.
If VCCP goes high (the system processor power rail is powered
up), then a fail-safe timer begins to count down. If the ADT7468
has been addressed by a valid SMBus transaction before the failsafe timeout (4.6 s) lapsed, then the ADT7468 operates normally, assuming the functionality of all the default registers. See
the flow chart in Figure 48.
ADT7468 IS POWERED UP
HAS THE ADT7468 BEEN
ACCESSED BY A VALID
SMBUS TRANSACTION?
Y
N
Figure 47 shows the signals that are exercised in the XNOR tree
test mode.
IS VCCP ABOVE 0.75V?
CHECK VCCP
N
Y
VID0
START FAIL-SAFE TIMER
VID1
HAS THE ADT7468 BEEN
ACCESSED BY A VALID
SMBUS TRANSACTION?
VID2
Y
N
VID3
FAIL-SAFE TIMER ELAPSES
AFTER THE FAIL-SAFE TIMEOUT
VID4
HAS THE ADT7468 BEEN
ACCESSED BY A VALID
SMBUS TRANSACTION?
TACH1
RUN THE FANS TO FULL SPEED
N
Y
TACH2
HAS THE ADT7468 BEEN
ACCESSED BY A VALID
SMBUS TRANSACTION?
TACH3
N
START UP THE
ADT7468 NORMALLY
TACH4
Figure 48. Power-On Flow Chart
PWM1/XTO
04499-0-040
PWM2
PWM3
SWITCH OFF FANS
Figure 47. XNOR Tree Test
Rev. 0 | Page 35 of 80
04499-0-043
Y
ADT7468
PROGRAMMING THE AUTOMATIC FAN SPEED CONTROL LOOP
Note: To more efficiently understand the automatic fan speed
control loop, it is strongly recommended to use the ADT7468
evaluation board and software while reading this section.
This section provides the system designer with an understanding of the automatic fan control loop, and provides step-by-step
guidance on effectively evaluating and selecting critical system
parameters. To optimize the system characteristics, the designer
needs to give some thought to system configuration, including
the number of fans, where they are located, and what temperatures are being measured in the particular system.
The mechanical or thermal engineer who is tasked with the
system thermal characterization should also be involved at the
beginning of the process.
AUTOMATIC FAN CONTROL OVERVIEW
The ADT7468 can automatically control the speed of fans based
upon the measured temperature. This is done independently of
CPU intervention once initial parameters are set up.
The ADT7468 has a local temperature sensor and two remote
temperature channels that can be connected to a CPU on-chip
thermal diode (available on Intel Pentium class and other
CPUs). These three temperature channels can be used as the
basis for automatic fan speed control to drive fans using pulsewidth modulation (PWM).
current consumption. The automatic fan speed control mode is
very flexible owing to the number of programmable parameters,
including TMIN and TRANGE. The TMIN and TRANGE values for a
temperature channel and, therefore, for a given fan are critical,
because they define the thermal characteristics of the system.
The thermal validation of the system is one of the most
important steps in the design process, so these values should be
selected carefully.
Figure 49 gives a top-level overview of the automatic fan control
circuitry on the ADT7468. From a systems-level perspective, up
to three system temperatures can be monitored and used to
control three PWM outputs. The three PWM outputs can be
used to control up to four fans. The ADT7468 allows the speed
of four fans to be monitored. Each temperature channel has a
thermal calibration block, allowing the designer to individually
configure the thermal characteristics of each temperature
channel. For example, one can decide to run the CPU fan when
CPU temperature increases above 60°C and a chassis fan when
the local temperature increases above 45°C. At this stage, the
designer has not assigned these thermal calibration settings to a
particular fan drive (PWM) channel. The right side of Figure 49
shows controls that are fan-specific. The designer has individual
control over parameters such as minimum PWM duty cycle, fan
speed failure thresholds, and even ramp control of the PWM
outputs. Automatic fan control, then, ultimately allows graceful
fan speed changes that are less perceptible to the system user.
Automatic fan speed control reduces acoustic noise by
optimizing fan speed according to accurately measured
temperature. Reducing fan speed can also decrease system
PWM
MIN
100%
PWM
CONFIG
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
REMOTE 1
TEMP
TMIN
TRANGE
THERMAL CALIBRATION
TMIN
PWM
MIN
100%
TRANGE
THERMAL CALIBRATION
REMOTE 2
TEMP
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM1
0%
MUX
LOCAL
TEMP
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
0%
Figure 49. Automatic Fan Control Block Diagram
Rev. 0 | Page 36 of 80
TACH1
PWM
CONFIG
PWM
GENERATOR
PWM2
TACH2
PWM
CONFIG
PWM
GENERATOR
PWM3
TACH3
04499-0-054
THERMAL CALIBRATION
ADT7468
STEP 1: HARDWARE CONFIGURATION
During system design, the motherboard sensing and control
capabilities should be addressed early in the design stages.
Decisions about how these capabilities are used should involve
the system thermal/mechanical engineer. Ask the following
questions:
How many fans will be supported in system, three or four?
This influences the choice of whether to use the TACH4
pin or to reconfigure it for the THERM function.
3.
Is the CPU fan to be controlled using the ADT7468 or will
it run at full speed 100% of the time?
If run at 100%, this frees up a PWM output, but the system
is louder.
What ADT7468 functionality will be used?
•
PWM2 or SMBALERT?
•
TACH4 fan speed measurement or overtemperature
THERM function?
4.
•
5 V voltage monitoring or overtemperature THERM
function?
•
12 V voltage monitoring or VID5 input?
Where will the ADT7468 be physically located in the
system?
This influences the assignment of the temperature
measurement channels to particular system thermal zones.
For example, locating the ADT7468 close to the VRM
controller circuitry allows the VRM temperature to be
monitored using the local temperature channel.
The ADT7468 offers multifunctional pins that can be
reconfigured to suit different system requirements and
physical layouts. These multifunction pins are software
programmable.
THERMAL CALIBRATION
PWM
CONFIG
PWM
MIN
100%
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 1 =
AMBIENT TEMP
TRANGE
THERMAL CALIBRATION
PWM
MIN
100%
LOCAL =
VRM TEMP
TRANGE
THERMAL CALIBRATION
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM1
0%
MUX
TMIN
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
0%
REMOTE 2 =
CPU TEMP
TACH1
PWM
CONFIG
PWM
GENERATOR
CPU FAN SINK
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
PWM3
TACH3
REAR CHASSIS
Figure 50. Hardware Configuration Example
Rev. 0 | Page 37 of 80
04499-0-055
1.
2.
ADT7468
RECOMMENDED IMPLEMENTATION 1
7.
5 V measurement input.
Configuring the ADT7468 as in Figure 51 provides the system
designer with the following features:
8.
VRM temperature using local temperature sensor.
9.
CPU temperature measured using the Remote 1
temperature channel.
1.
Six VID inputs (VID0 to VID5) for VRM10 support.
2.
Two PWM outputs for fan control of up to three fans. (The
front and rear chassis fans are connected in parallel.)
10. Ambient temperature measured through the Remote 2
temperature channel.
3.
Three TACH fan speed measurement inputs.
4.
VCC measured internally through Pin 4.
11. If not using VID5, this pin can be reconfigured as the 12 V
monitoring input.
5.
CPU core voltage measurement (VCORE).
6.
2.5 V measurement input used to monitor CPU current
(connected to VCOMP output of ADP316x VRM controller).
This is used to determine CPU power consumption.
FRONT
CHASSIS
FAN
12. Bidirectional THERM pin allows the monitoring of
PROCHOT output from an Intel P4 processor, for example,
or can be used as an overtemperature THERM output.
13. SMBALERT system interrupt output.
TACH2
PWM1
TACH1
CPU FAN
PWM3
REAR
CHASSIS
FAN
5(VRM9)/6(VRM10)
VID[0:4]/VID[0.5]
TACH3
D2+
D2–
THERM
PROCHOT
CPU
AMBIENT
TEMPERATURE
D1+
D1–
ADT7468
3.3VSB
5V
12V/VID5
SDA
SCL
VCOMP
SMBALERT
CURRENT
VCORE
GND
Figure 51. Recommended Implementation 1
Rev. 0 | Page 38 of 80
ICH
04499-0-056
ADP316x
VRM
CONTROLLER
ADT7468
RECOMMENDED IMPLEMENTATION 2
7.
5 V measurement input.
Configuring the ADT7468 as in Figure 52 provides the system
designer with the following features:
8.
VRM temperature using local temperature sensor.
9.
CPU temperature measured using the Remote 1
temperature channel.
1.
Six VID inputs (VID0 to VID5) for VRM10 support.
2.
Three PWM outputs for fan control of up to three fans.
(All three fans can be individually controlled.)
10. Ambient temperature measured through the Remote 2
temperature channel.
3.
Three TACH fan speed measurement inputs.
4.
VCC measured internally through Pin 4.
11. If not using VID5, this pin can be reconfigured as the 12 V
monitoring input.
5.
CPU core voltage measurement (VCORE).
6.
2.5 V measurement input used to monitor CPU current
(connected to VCOMP output of ADP316x VRM controller).
This is used to determine CPU power consumption.
FRONT
CHASSIS
FAN
12. Bidirectional THERM pin allows the monitoring of
PROCHOT output from an Intel P4 processor, for example,
or can be used as an overtemperature THERM output.
TACH2
PWM1
TACH1
CPU FAN
PWM3
REAR
CHASSIS
FAN
5(VRM9)/6(VRM10)
VID[0:4]/VID[0.5]
TACH3
D2+
D2–
THERM
PROCHOT
AMBIENT
TEMPERATURE
CPU
D1+
D1–
ADT7468
3.3VSB
5V
12V/VID5
SDA
SCL
VCOMP
CURRENT
ICH
VCORE
GND
Figure 52. Recommended Implementation 2
Rev. 0 | Page 39 of 80
04499-0-057
ADP316x
VRM
CONTROLLER
ADT7468
101 = Fastest speed calculated by local and Remote 2
temperature controls PWMx
STEP 2: CONFIGURING THE MUX
After the system hardware configuration is determined, the fans
can be assigned to particular temperature channels. Not only
can fans be assigned to individual channels, but the behavior of
the fans is also configurable. For example, fans can be run under
automatic fan control, can be run manually (under software
control), or can be run at the fastest speed calculated by
multiple temperature channels. The MUX is the bridge between
temperature measurement channels and the three PWM
outputs.
110 = Fastest speed calculated by all three temperature
channels controls PWMx
The Fastest Speed Calculated options pertain to controlling one
PWM output based on multiple temperature channels. The
thermal characteristics of the three temperature zones can be
set to drive a single fan. An example would be the fan turning
on when Remote 1 temperature exceeds 60°C or if the local
temperature exceeds 45°C.
Bits <7:5> (BHVR) of Registers 0x5C, 0x5D, and 0x5E (PWM
configuration registers) control the behavior of the fans
connected to the PWM1, PWM2, and PWM3 outputs. The
values selected for these bits determine how the MUX connects
a temperature measurement channel to a PWM output.
Other MUX Options
<7:5> (BHVR), Registers 0x5C, 0x5D, 0x5E.
011 = PWMx runs full speed
100 = PWMx disabled (default)
Automatic Fan Control MUX Options
<7:5> (BHVR), Registers 0x5C, 0x5D, 0x5E.
111 = manual mode. PWMx is runner under software
control. In this mode, PWM duty cycle registers
(Registers 0x30 to 0x32) are writable and control the PWM
outputs.
000 = Remote 1 temperature controls PWMx
001 = local temperature controls PWMx
010 = Remote 2 temperature controls PWMx
MUX
PWM
CONFIG
PWM
MIN
100%
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 1 =
AMBIENT TEMP
TRANGE
THERMAL CALIBRATION
PWM
MIN
100%
LOCAL =
VRM TEMP
TRANGE
THERMAL CALIBRATION
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM1
0%
MUX
TMIN
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
0%
REMOTE 2 =
CPU TEMP
TACH1
PWM
CONFIG
PWM
GENERATOR
CPU FAN SINK
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
PWM3
TACH3
REAR CHASSIS
Figure 53. Assigning Temperature Channels to Fan Channels
Rev. 0 | Page 40 of 80
04499-0-058
THERMAL CALIBRATION
ADT7468
MUX Configuration Example
Example MUX Settings
This is an example of how to configure the MUX in a system
using the ADT7468 to control three fans. The CPU fan sink is
controlled by PWM1, the front chassis fan is controlled by
PWM2, and the rear chassis fan is controlled by PWM3. The
MUX is configured for the following fan control behavior:
<7:5> (BHVR), PWM1 Configuration Register 0x5C.
PWM1 (CPU fan sink) is controlled by the fastest speed
calculated by the local (VRM temperature) and Remote 2
(processor) temperature. In this case, the CPU fan sink is
also being used to cool the VRM.
•
PWM2 (front chassis fan) is controlled by the Remote 1
temperature (ambient).
•
PWM3 (rear chassis fan) is controlled by the Remote 1
temperature (ambient).
THERMAL CALIBRATION
<7:5> (BHVR), PWM2 Configuration Register 0x5D.
000 = Remote 1 temperature controls PWM2
<7:5> (BHVR), PWM3 Configuration Register 0x5E.
000 = Remote 1 temperature controls PWM3
These settings configure the MUX, as shown in Figure 54.
PWM
CONFIG
PWM
MIN
100%
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 2 =
CPU TEMP
TRANGE
THERMAL CALIBRATION
MUX
100%
LOCAL =
VRM TEMP
TRANGE
THERMAL CALIBRATION
TMIN
PWM
MIN
0%
PWM
MIN
100%
TRANGE
PWM1
0%
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
0%
TACH1
PWM
CONFIG
PWM
GENERATOR
CPU FAN SINK
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
PWM3
TACH3
REMOTE 1 =
AMBIENT TEMP
REAR CHASSIS
Figure 54. MUX Configuration Example
Rev. 0 | Page 41 of 80
04499-0-059
•
101 = Fastest speed calculated by local and Remote 2
temperature controls PWM1
ADT7468
STEP 3: TMIN SETTINGS FOR THERMAL
CALIBRATION CHANNELS
TMIN Registers
TMIN is the temperature at which the fans start to turn on under
automatic fan control. The speed at which the fan runs at TMIN is
programmed later. The TMIN values chosen are temperature
channel specific, for example, 25°C for ambient channel, 30°C
for VRM temperature, and 40°C for processor temperature.
Reg. 0x68, Local Temperature TMIN = 0x9A (90°C)
Reg. 0x67, Remote 1 Temperature TMIN = 0x9A (90°C)
TMIN is an 8-bit value, either twos complement or Offset 64, that
can be programmed in 1°C increments. There is a TMIN register
associated with each temperature measurement channel:
Remote 1 Local, and Remote 2 Temp. Once the TMIN value is
exceeded, the fan turns on and runs at the minimum PWM
duty cycle. The fan turns off once the temperature has dropped
below TMIN – THYST.
To overcome fan inertia, the fan is spun up until two valid
TACH rising edges are counted. See the Fan Startup Timeout
section for more details. In some cases, primarily for psychoacoustic reasons, it is desirable that the fan never switch off
below TMIN. Bits <7:5> of Enhanced Acoustics Register 1 (Reg.
0x62), when set, keep the fans running at the PWM minimum
duty cycle, if the temperature should fall below TMIN.
Reg. 0x69, Remote 2 Temperature TMIN = 0x9A (90°C)
Enhance Acoustics Register 1 (Reg. 0x62)
Bit 7 (MIN3) = 0, PWM3 is off (0% PWM duty cycle) when
temperature is below TMIN – THYST.
Bit 7 (MIN3) = 1, PWM3 runs at PWM3 minimum duty cycle
below TMIN – THYST.
Bit 6 (MIN2) = 0, PWM2 is off (0% PWM duty cycle) when
temperature is below TMIN – THYST.
Bit 6 (MIN2) = 1, PWM2 runs at PWM2 minimum duty cycle
below TMIN – THYST.
Bit 5 (MIN1) = 0, PWM1 is off (0% PWM duty cycle) when
temperature is below TMIN – THYST.
Bit 5 (MIN1) = 1, PWM1 runs at PWM1 minimum duty cycle
below TMIN – THYST.
PWM DUTYCYCLE
100%
0%
TMIN
PWM
CONFIG
PWM
MIN
100%
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 2 =
CPU TEMP
TRANGE
THERMAL CALIBRATION
PWM
MIN
100%
LOCAL =
VRM TEMP
TRANGE
THERMAL CALIBRATION
TMIN
PWM
MIN
0%
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
100%
TRANGE
PWM1
0%
MUX
TMIN
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
TACH1
PWM
CONFIG
PWM
GENERATOR
CPU FAN SINK
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
PWM3
TACH3
REMOTE 1 =
AMBIENT TEMP
REAR CHASSIS
Figure 55. Understanding the TMIN Parameter
Rev. 0 | Page 42 of 80
04499-0-060
THERMAL CALIBRATION
ADT7468
STEP 4: PWMMIN FOR EACH PWM (FAN) OUTPUT
Programming the PWMMIN Registers
PWMMIN is the minimum PWM duty cycle at which each fan in
the system runs. It is also the start speed for each fan under
automatic fan control once the temperature rises above TMIN.
For maximum system acoustic benefit, PWMMIN should be as
low as possible. Depending on the fan used, the PWMMIN setting
is usually in the 20% to 33% duty cycle range. This value can be
found through fan validation.
The PWMMIN registers are 8-bit registers that allow the
minimum PWM duty cycle for each output to be configured
anywhere from 0% to 100%. This allows the minimum PWM
duty cycle to be set in steps of 0.39%.
The value to be programmed into the PWMMIN register is given
by
Value (decimal) = PWMMIN/0.39
PWM DUTY CYCLE
100%
Example 1: For a minimum PWM duty cycle of 50%,
Value (decimal) = 50/0.39 = 128 (decimal)
Value = 128 (decimal) or 80 (hex)
Example 2: For a minimum PWM duty cycle of 33%,
PWMMIN
Value (decimal) = 33/0.39 = 85 (decimal)
Value = 85 (decimal)l or 54 (hex)
TMIN
TEMPERATURE
04499-0-061
0%
PWMMIN Registers
Figure 56. PWMMIN Determines Minimum PWM Duty Cycle
More than one PWM output can be controlled from a single
temperature measurement channel. For example, Remote 1
temperature can control PWM1 and PWM2 outputs. If two
different fans are used on PWM1 and PWM2, then the fan
characteristics can be set up differently. As a result, Fan 1 driven
by PWM1 can have a different PWMMIN value than that of Fan 2
connected to PWM2. Figure 57 illustrates this as PWM1MIN
(front fan) is turned on at a minimum duty cycle of 20%, while
PWM2MIN (rear fan) turns on at a minimum of 40% duty cycle.
Note, however, that both fans turn on at exactly the same
temperature, defined by TMIN.
Note on Fan Speed and PWM Duty Cycle
The PWM duty cycle does not directly correlate to fan speed in
RPM. Running a fan at 33% PWM duty cycle does not equate to
running the fan at 33% speed. Driving a fan at 33% PWM duty
cycle actually runs the fan at closer to 50% of its full speed. This
is because fan speed in %RPM generally relates to the square
root of PWM duty cycle. Given a PWM square wave as the
drive signal, fan speed in RPM approximates to
% fanspeed = PWM duty cycle × 10
STEP 5: PWMMAX FOR PWM (FAN) OUTPUTS
100%
PWM DUTY CYCLE
Reg. 0x64, PWM1 Minimum Duty Cycle = 0x80 (50% default)
Reg. 0x65 PWM2 Minimum Duty Cycle = 0x80 (50% default)
Reg. 0x66, PWM3 Minimum Duty Cycle = 0x80 (50% default)
PWMMAX is the maximum duty cycle that each fan in the system
runs at under the automatic fan speed control loop. For
maximum system acoustic benefit, PWMMAX should be as low as
possible, but should be capable of maintaining the processor
temperature limit at an acceptable level. If the THERM
temperature limit is exceeded, the fans are still boosted to 100%
for fail-safe cooling.
M2
PW
M1
PW
PWM2MIN
PWM1MIN
TMIN
TEMPERATURE
04499-0-062
0%
Figure 57. Operating Two Different Fans from a Single Temperature Channel
There is a PWMMAX limit for each fan channel. The default value
of this register is 0xFF and so has no effect unless it is
programmed.
Rev. 0 | Page 43 of 80
ADT7468
STEP 6: TRANGE FOR TEMPERATURE CHANNELS
TRANGE is the range of temperature over which automatic fan
control occurs once the programmed TMIN temperature has
been exceeded. TRANGE is a temperature slope, not an arbitrary
value, that is, a TRANGE of 40°C holds true only for PWMMIN =
33%. If PWMMIN is increased or decreased, the effective TRANGE
changes.
PWMMAX
PWMMIN
0%
100%
PWM DUTY CYCLE
Figure 58. PWMMAX Determines Maximum PWM Duty Cycle below the THERM
Temperature Limit
Programming the PWMMAX Registers
The PWMMAX registers are 8-bit registers that allow the
maximum PWM duty cycle for each output to be configured
anywhere from 0% to 100%. This allows the maximum PWM
duty cycle to be set in steps of 0.39%.
The value to be programmed into the PWMMAX register is given
by
Value (decimal) = PWMMAX/0.39
Example 1: For a maximum PWM duty cycle of 50%,
Value (decimal) – 50/0.39 = 128 (decimal)
Value = 128 (decimal) or 80 (hex)
0%
TMIN
The TRANGE or fan control slope is determined by the following
procedure:
1.
Determine the maximum operating temperature for that
channel (for example, 70°C).
2.
Determine experimentally the fan speed (PWM duty cycle
value) that does not exceed the temperature at the worstcase operating points. (For example, 70°C is reached when
the fans are running at 50% PWM duty cycle.)
3.
Determine the slope of the required control loop to meet
these requirements.
4.
Using the ADT7468 evaluation software, you can
graphically program and visualize this functionality. Ask
your local Analog Devices representative for details.
Value (decimal) = 75/0.39 = 85 (decimal)
PWMMAX Registers
Reg. 0x38, PWM1 Maximum Duty Cycle = 0xFF
(100% default)
TEMPERATURE
Figure 59. TRANGE Parameter Affects Cooling Slope
Example 2: For a minimum PWM duty cycle of 75%,
Value = 192 (decimal) or C0 (hex)
PWMMIN
04499-0-064
TEMPERATURE
04499-0-063
TMIN
TRANGE
Reg. 0x39, PWM2 Maximum Duty Cycle = 0xFF
(100% default)
Reg. 0x3A, PWM3 Maximum Duty Cycle = 0xFF
(100% default)
See the Note on Fan Speed and PWM Duty Cycle on Page 43.
PWM DUTY CYCLE
100%
50%
33%
0%
30°C
40°C
TMIN
Figure 60. Adjusting PWMMIN Affects TRANGE
Rev. 0 | Page 44 of 80
04499-0-065
PWM DUTY CYCLE
100%
ADT7468
TRANGE is implemented as a slope, which means that as PWMMIN
is changed, TRANGE changes, but the actual slope remains the
same. The higher the PWMMIN value, the smaller the effective
TRANGE, that is, the fan reaches full speed (100%) at a lower
temperature.
Example: Calculate TMAX, given that TMIN = 30°C, TRANGE = 40°C,
and PWMMIN = 33% duty cycle = 85 (decimal).
TMAX = TMIN + (Max DC − Min DC) × TRANGE /170
TMAX = 30°C + (100% − 33%) × 40°C/170
TMAX = 30°C + (255 − 85) × 40°C/170
TMAX = 70°C (effective TRANGE = 40°C)
PWM DUTY CYCLE
100%
Example: Calculate TMAX, given that TMIN = 30°C, TRANGE = 40°C,
and PWMMIN = 50% duty cycle = 128 (decimal).
TMAX = TMIN + (Max DC − Min DC) × TRANGE /170
TMAX = 30°C + (100% − 50%) × 40°C/170
TMAX = 30°C + (255 − 128) × 40°C/170
TMAX = 60°C (effective TRANGE = 30°C)
50%
33%
25%
10%
0%
Selecting a TRANGE Slope
30°C
TMIN
The TRANGE value can be selected for each temperature channel:
Remote 1, local, and Remote 2 temperature. Bits <7:4> (TRANGE)
of Registers 0x5F to 0x61 define the TRANGE value for each
temperature channel.
04499-0-066
40°C
45°C
54°C
Figure 61. Increasing PWMMIN Changes Effective TRANGE
Table 13. Selecting a TRANGE Value
For a given TRANGE value, the temperature at which the fan runs
at full speed for different PWMMIN values can be easily
calculated:
TMAX = TMIN + (Max DC − Min DC) × TRANGE /170
where:
TMAX is the temperature at which the fan runs full speed.
TMIN is the temperature at which the fan turns on.
Max DC is the maximum duty cycle (100%) = 255 decimal.
Min DC is equal to PWMMIN.
TRANGE is the duty PWM duty cycle vs. temperature slope.
Example: Calculate T, given that TMIN = 30°C, TRANGE = 40°C,
and PWMMIN = 10% duty cycle = 26 (decimal).
TMAX = TMIN + (Max DC − Min DC) × TRANGE /170
TMAX = 30°C + (100% − 10%) × 40°C/170
TMAX = 30°C + (255 − 26) × 40°C/170
TMAX = 84°C (effective TRANGE = 54°C)
Bits <7:4>1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
1
TRANGE (°C)
2
2.5
3.33
4
5
6.67
8
10
13.33
16
20
26.67
32 (default)
40
53.33
80
Register 0x5F configures Remote 1 TRANGE.
Register 0x60 configures Local TRANGE.
Register 0x61 configures Remote 2 TRANGE.
Example: Calculate TMAX, given that TMIN = 30°C, TRANGE = 40°C,
and PWMMIN = 25% duty cycle = 64 (decimal).
Summary of TRANGE Function
TMAX = TMIN + (Max DC − Min DC) × TRANGE /170
TMAX = 30°C + (100% − 25%) × 40°C/170
TMAX = 30°C + (255 − 64) × 40°C/170
TMAX = 75°C (effective TRANGE = 45°C)
When using the automatic fan control function, the temperature
at which the fan reaches full speed can be calculated by
TMAX = TMIN + TRANGE
Equation 1 holds true only when PWMMIN is equal to 33%
PWM duty cycle.
Rev. 0 | Page 45 of 80
(1)
ADT7468
(2)
where:
(Max DC − Min DC) × TRANGE/170 is the effective TRANGE value.
2°C
2.5°C
90
3.33°C
4°C
80
5°C
70
6.67°C
8°C
60
10°C
50
13.3°C
16°C
40
20°C
30
26.6°C
32°C
20
See the Note on Fan Speed and PWM Duty Cycle.
Figure 62 shows PWM duty cycle versus temperature for each
TRANGE setting. The lower graph shows how each TRANGE setting
affects fan speed versus temperature. As can be seen from the
graph, the effect on fan speed is nonlinear.
100
8°C
10°C
13.3°C
16°C
40
20°C
30
100
120
3.33°C
4°C
5°C
6.67°C
8°C
10°C
50
13.3°C
16°C
40
20°C
30
53.3°C
40
60
80
TEMPERATURE ABOVE TMIN
2.5°C
60
0
0
80°C
80°C
2°C
70
40°C
20
120
26.6°C
32°C
40°C
10
32°C
10
100
20
26.6°C
20
53.3°C
20
40
60
80
TEMPERATURE ABOVE TMIN
100
120
80°C
Figure 63. TRANGE and % Fan Speed Slopes with PWMMIN = 20%
100
2°C
Example: Determining TRANGE for Each Temperature Channel
2.5°C
90
The following example shows how the different TMIN and TRANGE
settings can be applied to three different thermal zones. In this
example, the following TRANGE values apply:
3.33°C
80
FAN SPEED (% OF MAX)
FAN SPEED (% OF MAX)
6.67°C
4°C
5°C
70
6.67°C
8°C
60
TRANGE = 80°C for ambient temperature
TRANGE = 53.3°C for CPU temperature
TRANGE = 40°C for VRM temperature
10°C
50
13.3°C
16°C
40
20°C
30
26.6°C
32°C
20
40°C
10
53.3°C
20
40
60
80
TEMPERATURE ABOVE TMIN
100
120
80°C
04499-0-067
PWM DUTY CYCLE (%)
5°C
50
40
60
80
TEMPERATURE ABOVE TMIN
80
4°C
60
20
90
3.33°C
70
53.3°C
100
2.5°C
80
0
0
0
0
2°C
90
0
0
40°C
10
04499-0-068
TMAX = TMIN + (Max DC − Min DC) × TRANGE/170
100
PWM DUTY CYCLE (%)
Increasing or decreasing PWMMIN changes the effective TRANGE,
although the fan control still follows the same PWM duty cycle
to temperature slope. The effective TRANGE for different PWMMIN
values can be calculated using Equation 2:
Figure 62. TRANGE vs. Actual Fan Speed Profile
The graphs in Figure 62 assume that the fan starts from 0%
PWM duty cycle. Clearly, the minimum PWM duty cycle,
PWMMIN, needs to be factored in to see how the loop actually
performs in the system. Figure 63 shows how TRANGE is affected
when the PWMMIN value is set to 20%. It can be seen that the fan
actually runs at about 45% fan speed when the temperature
exceeds TMIN.
This example uses the MUX configuration described in Step 2,
with the ADT7468 connected as shown in Figure 54. Both CPU
temperature and VRM temperature drive the CPU fan
connected to PWM1. Ambient temperature drives the front
chassis fan and rear chassis fan connected to PWM2 and
PWM3. The front chassis fan is configured to run at PWMMIN =
20%. The rear chassis fan is configured to run at PWMMIN =
30%. The CPU fan is configured to run at PWMMIN = 10%.
Note on 4-Wire Fans
The control range for 4-wire fans is much wider than that of
2-wire or 3-wire fans. In many cases, 4-wire fans can start with a
PWM drive of as little as 20%.
Rev. 0 | Page 46 of 80
ADT7468
100
The fans remain running at 100% until the temperature drops
below TTHERM minus hysteresis, where hysteresis is the number
90
PWM DUTY CYCLE (%)
80
programmed into the Hysteresis Registers 0x6D and 0x6E. The
default hysteresis value is 4°C.
70
60
The TTHERM limit should be considered the maximum worst-case
50
operating temperature of the system. Because exceeding any
TTHERM limit runs all fans at 100%, it has very negative acoustic
40
30
effects. Ultimately, this limit should be set up as a fail-safe, and
one should ensure that it is not exceeded under normal system
operating conditions.
20
10
0
0
10
20
30
40
50
60
70
80
90
Note that the TTHERM limits are nonmaskable and affect the fan
100
TEMPERATURE ABOVE TMIN
speed no matter how automatic fan control settings are
configured. This allows some flexibility, because a TRANGE value
can be selected based on its slope, while a hard limit (such as
70°C), can be programmed as TMAX (the temperature at which
the fan reaches full speed) by setting TTHERM to that limit (for
100
90
FAN SPEED (% MAX RPM)
80
70
example, 70°C).
60
THERM Registers
50
Reg. 0x6A, Remote 1 THERM limit = 0xA4 (100°C default)
40
30
Reg. 0x6B, Local THERM limit = 0xA4 (100°C default)
20
Reg. 0x6C, Remote 2 THERM limit = 0xA4 (100°C default)
10
10
20
30
40
50
60
70
80
90
100
TEMPERATURE ABOVE TMIN
Hysteresis Registers
04499-0-069
0
0
Reg. 0x6D, Remote 1, Local Hysteresis Register
<7:4>, Remote 1 temperature hysteresis (4°C default).
Figure 64. TRANGE and % Fan Speed Slopes for VRM, Ambient, and
CPU Temperature Channels
<3:0>, Local temperature hysteresis (4°C default).
STEP 7: TTHERM FOR TEMPERATURE CHANNELS
Reg. 0x6E, Remote 2 Temperature Hysteresis Register
TTHERM is the absolute maximum temperature allowed on a
temperature channel. Above this temperature, a component
such as the CPU or VRM might be operating beyond its safe
operating limit. When the temperature measured exceeds
TTHERM, all fans are driven at 100% PWM duty cycle (full speed)
to provide critical system cooling.
<7:4>, Remote 2 temperature hysteresis (4°C default).
Because each hysteresis setting is four bits, hysteresis values are
programmable from 1°C to 15°C. It is not recommended that
hysteresis values ever be programmed to 0°C, because this
disables hysteresis. In effect, this would cause the fans to cycle
between normal speed and 100% speed, creating unsettling
acoustic noise.
Rev. 0 | Page 47 of 80
ADT7468
TRANGE
PWM DUTYCYCLE
100%
0%
TMIN
T THERM
PWM
CONFIG
PWM
MIN
100%
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 2 =
CPU TEMP
TRANGE
THERMAL CALIBRATION
TMIN
PWM
MIN
100%
TRANGE
THERMAL CALIBRATION
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM1
0%
MUX
LOCAL =
VRM TEMP
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACH1
PWM
CONFIG
PWM
GENERATOR
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
TACHOMETER 3
AND 4
MEASUREMENT
0%
CPU FAN SINK
PWM3
TACH3
REMOTE 1 =
AMBIENT TEMP
REAR CHASSIS
04499-0-070
THERMAL CALIBRATION
Figure 65. How TTHERM Relates to Automatic Fan Control
Hysteresis Registers
STEP 8: THYST FOR TEMPERATURE CHANNELS
THYST is the amount of extra cooling a fan provides after the
temperature measured has dropped back below TMIN before the
fan turns off. The premise for temperature hysteresis (THYST) is
that, without it, the fan would merely chatter or cycle on and off
regularly whenever temperature is hovering at about the TMIN
setting.
The THYST value chosen determines the amount of time needed
for the system to cool down or heat up as the fan is turning on
and off. Values of hysteresis are programmable in the range 1°C
to 15°C. Larger values of THYST prevent the fans from chattering
on and off. The THYST default value is set at 4°C.
The THYST setting applies not only to the temperature hysteresis
for fan on/off, but the same setting is used for the TTHERM
Reg. 0x6D, Remote 1, Local Hysteresis Register
<7:4>, Remote 1 temperature hysteresis (4°C default).
<3:0>, local temperature hysteresis (4°C default).
Reg. 0x6E, Remote 2 Temp Hysteresis Register
<7:4>, Remote 2 temperature hysteresis (4°C default).
In some applications, it is required that fans not turn off below
TMIN, but remain running at PWMMIN. Bits <7:5> of Enhanced
Acoustics Register 1 (Reg. 0x62) allow the fans to be turned off
or to be kept spinning below TMIN. If the fans are always on, the
THYST value has no effect on the fan when the temperature drops
below TMIN.
hysteresis value, described in Step 6. Therefore, programming
Registers 0x6D and 0x6E sets the hysteresis for both fan on/off
and the THERM function.
Rev. 0 | Page 48 of 80
ADT7468
TRANGE
PWM DUTYCYCLE
100%
0%
T THERM
THERMAL CALIBRATION
PWM
CONFIG
PWM
MIN
100%
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 2 =
CPU TEMP
TRANGE
THERMAL CALIBRATION
TMIN
PWM
MIN
100%
TRANGE
THERMAL CALIBRATION
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM1
0%
MUX
LOCAL =
VRM TEMP
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
0%
TACH1
PWM
CONFIG
PWM
GENERATOR
CPU FAN SINK
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
PWM3
TACH3
REMOTE 1 =
AMBIENT TEMP
REAR CHASSIS
04499-0-071
TMIN
Figure 66. The THYST Value Applies to Fan On/Off Hysteresis and THERM Hysteresis
Enhance Acoustics Register 1 (Reg. 0x62)
DYNAMIC TMIN CONTROL MODE
Bit 7 (MIN3) = 0, PWM3 is off (0% PWM duty cycle) when
temperature is below TMIN − THYST.
Bit 7 (MIN3) = 1, PWM3 runs at PWM3 minimum duty cycle
below TMIN − THYST.
Bit 6 (MIN2) = 0, PWM2 is off (0% PWM duty cycle) when
temperature is below TMIN − THYST.
Bit 6 (MIN2) = 1, PWM2 runs at PWM2 minimum duty cycle
below TMIN − THYST.
Bit 5 (MIN1) = 0, PWM1 is off (0% PWM duty cycle) when
temperature is below TMIN − THYST.
Bit 5 (MIN1) = 1, PWM1 runs at PWM1 minimum duty cycle
below TMIN − THYST.
In addition to the automatic fan speed control mode described
in the Automatic Fan Control Overview section, the ADT7468
has a mode that extends the basic automatic fan speed control
loop. Dynamic TMIN control allows the ADT7468 to intelligently
adapt the system’s cooling solution for best system performance
or lowest possible system acoustics, depending on user or
design requirements. Use of dynamic TMIN control alleviates the
need to design for worst-case conditions and significantly
reduces system design and validation time.
Designing for Worst-Case Conditions
System design must always allow for worst-case conditions. In
PC design, the worst-case conditions include, but are not
limited to the following:
Rev. 0 | Page 49 of 80
ADT7468
Worst-Case Altitude
A computer can be operated at different altitudes. The
altitude affects the relative air density, which alters the
effectiveness of the fan cooling solution. For example,
comparing 40°C air temperature at 10,000 ft. to 20°C air
temperature at sea level, relative air density is increased by
40%. This means that the fan can spin 40% slower and
make less noise at sea level than at 10,000 ft. while keeping
the system at the same temperature at both locations.
•
Worst-Case Fan
Due to manufacturing tolerances, fan speeds in RPM are
normally quoted with a tolerance of ±20%. The designer
needs to assume that the fan RPM can be 20% below
tolerance. This translates to reduced system airflow and
elevated system temperature. Note that fans 20% out of
tolerance can negatively impact system acoustics, because
they run faster and generate more noise.
•
Worst-Case Chassis Airflow
The same motherboard can be used in a number of
different chassis configurations. The design of the chassis
and the physical location of fans and components
determine the system thermal characteristics. Moreover, for
a given chassis, the addition of add-in cards, cables, or
other system configuration options can alter the system
airflow and reduce the effectiveness of the system cooling
solution. The cooling solution can also be inadvertently
altered by the end user. (For example, placing a computer
against a wall can block the air ducts and reduce system
airflow.)
VENTS
FAN
FAN
I/O CARDS
GOOD CPU AIRFLOW
FAN
POWER
SUPPLY
CPU
VENTS
POWER
SUPPLY
POOR CPU
AIRFLOW
DRIVE
BAYS
CPU
DRIVE
BAYS
VENTS
GOOD VENTING =
GOOD AIR EXCHANGE
POOR VENTING =
POOR AIR EXCHANGE
04499-0-072
I/O CARDS
Figure 67. Chassis Airflow Issues
•
Worst-Case Processor Power Consumption
This data sheet maximum does not necessarily reflect the
true processor power consumption. Designing for worstcase CPU power consumption can result in a processor
becoming overcooled (generating excess system noise).
•
Worst-Case Peripheral Power Consumption
The tendency is to design to data sheet maximums for
peripheral components (again overcooling the system).
•
Worst-Case Assembly
Every system manufactured is unique because of
manufacturing variations. Heat sinks may be loose fitting
or slightly misaligned. Too much or too little thermal
grease might be used, or variations in application pressure
for thermal interface material could affect the efficiency of
the thermal solution. Accounting for manufacturing
variations in every system is difficult; therefore, the system
must be designed for the worst case.
TA
θSA
HEAT
SINK
TS
θCA
θTIMS
THERMAL
INTERFACE
MATERIAL
TTIM
θCTIM
INTEGRATED
HEAT
SPREADER
TC
θCS
θJA
θTIMC
PROCESSOR
θJTIM
SUBSTRATE
EPOXY
THERMAL INTERFACE MATERIAL
TTIM
TJ
04499-0-073
•
Figure 68. Thermal Model
Although a design usually accounts for worst-case conditions in
all these cases, the actual system is almost never operated at
worst-case conditions. The alternative to designing for the worst
case is to use the dynamic TMIN control function.
Dynamic TMIN Control Overview
Dynamic TMIN control mode builds upon the basic automatic
fan control loop by adjusting the TMIN value based on system
performance and measured temperature. This is important,
because, instead of designing for the worst case, the system
thermals can be defined as operating zones. ADT7468 can selfadjust its fan control loop to maintain either an operating zone
temperature or a system target temperature. For example, one
can specify that the ambient temperature in a system should be
maintained at 50°C. If the temperature is below 50°C, the fans
might not need to run or might run very slowly. If the
temperature is higher than 50°C, the fans need to throttle up.
The challenge presented by any thermal design is finding the
right settings to suit the system’s fan control solution. This can
involve designing for the worst case, followed by weeks of
system thermal characterization, and finally fan acoustic
optimization (for psycho-acoustic reasons). Getting the most
benefit from the automatic fan control mode involves characterizing the system to find the best TMIN and TRANGE settings for the
control loop, and the best PWMMIN value for the quietest fan
speed setting. Using the ADT7468’s dynamic TMIN control mode,
however, shortens the characterization time and alleviates
tweaking the control loop settings, because the device can selfadjust during system operation.
Dynamic TMIN control mode is operated by specifying the
operating zone temperatures required for the system. Associated
with this control mode are three operating point registers, one
Rev. 0 | Page 50 of 80
ADT7468
for each temperature channel. This allows the system thermal
solution to be broken down into distinct thermal zones. For
example, CPU operating temperature is 70°C, VRM operating
temperature is 80°C, and ambient operating temperature is
50°C. The ADT7468 dynamically alters the control solution to
maintain each zone temperature as closely as possible to its
target operating point.
Operating Point Registers
Reg. 0x33, Remote 1 Operating Point = 0xA4 (100°C default)
Reg. 0x34, Local Operating Point = 0xA4 (100°C default)
Reg. 0x35, Remote 2 Operating Point = 0xA4 (100°C default)
TEMPERATURE
TLOW
TMIN OPERATING THIGH T THERM TRANGE
POINT
04499-0-074
PWM DUTY CYCLE
Figure 69 shows an overview of the parameters that affect the
operation of the dynamic TMIN control loop.
Table 14 provides a brief description of each parameter.
TMIN
Operating
point
TTHERM
TRANGE
STEP 9: OPERATING POINTS FOR TEMPERATURE
CHANNELS
The operating point for each temperature channel is the optimal
temperature for that thermal zone. The hotter each zone is
allowed to be, the quieter the system, because the fans are not
required to run as fast. The ADT7468 increases or decreases fan
speeds as necessary to maintain the operating point
temperature, allowing for system-to-system variation and
removing the need for worst-case design. If a sensible operating
point value is chosen, any TMIN value can be selected in the
system characterization. If the TMIN value is too low, the fans run
sooner than required, and the temperature is below the operating point. In response, the ADT7468 increases TMIN to keep the
fans off longer and to allow the temperature zone to get closer
to the operating point. Likewise, too high a TMIN value causes
the operating point to be exceeded, and in turn, the ADT7468
reduces TMIN to turn the fans on sooner to cool the system.
Programming Operating Point Registers
Operating Point Registers
Table 14. TMIN Control Loop Parameters
THIGH
Because the dynamic TMIN control mode is a basic extension of
the automatic fan control mode, program the automatic fan
control mode parameters first, as described in Step 1 to Step 8,
then proceed with dynamic TMIN control mode programming.
There are three operating point registers, one for each
temperature channel. These 8-bit registers allow the operating
point temperatures to be programmed with 1°C resolution.
Figure 69. Dynamic TMIN Control Loop
Parameter
TLOW
Dynamic TMIN Control Programming
Description
If the temperature drops below the TLOW limit, an
error flag is set in a status register and an
SMBALERT interrupt can be generated.
If the temperature exceeds the THIGH limit, an
error flag is set in a status register and an
SMBALERT interrupt can be generated.
The temperature at which the fan turns on
under automatic fan speed control.
The target temperature for a particular
temperature zone. The ADT7468 attempts to
maintain system temperature at about the
operating point by adjusting the TMIN parameter
of the control loop.
If the temperature exceeds this critical limit, the
fans can be run at 100% for maximum cooling.
Programs the PWM duty cycle vs. temperature
control slope.
Reg. 0x33, Remote 1 Operating Point = 0xA4 (100°C default)
Reg. 0x34, Local Operating Point = 0xA4 (100°C default)
Reg. 0x35, Remote 2 Operating Point = 0xA4 (100°C default)
Rev. 0 | Page 51 of 80
ADT7468
OPERATING
POINT
TMIN
REMOTE 2 =
CPU TEMP
TRANGE
THERMAL CALIBRATION
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
PWM
MIN
100%
LOCAL =
VRM TEMP
TRANGE
THERMAL CALIBRATION
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM
GENERATOR
PWM1
0%
MUX
TMIN
PWM
CONFIG
PWM
MIN
100%
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACH1
PWM
CONFIG
PWM
GENERATOR
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
TACHOMETER 3
AND 4
MEASUREMENT
0%
CPU FAN SINK
PWM3
TACH3
REMOTE 1 =
AMBIENT TEMP
REAR CHASSIS
04499-0-075
THERMAL CALIBRATION
Figure 70. Operating Point Value Dynamically Adjusts Automatic Fan Control Settings
STEP 10: HIGH AND LOW LIMITS FOR
TEMPERATURE CHANNELS
How Dynamic TMIN Control Works
The low limit defines the temperature at which the TMIN value
starts to be increased, if temperature falls below this value. This
has the net effect of reducing the fan speed, allowing the system
to get hotter. An interrupt can be generated when the temperature drops below the low limit.
1.
Set the target temperature for the temperature zone, which
could be, for example, the Remote 1 thermal diode. This
value is programmed to the Remote 1 operating
temperature register.
2.
As the temperature in that zone (Remote 1 temperature)
rises toward and exceeds the operating point temperature,
TMIN is reduced and the fan speed increases.
3.
As the temperature drops below the operating point
temperature, TMIN is increased and the fan speed is reduced.
The basic premise is as follows:
The high limit defines the temperature at which the TMIN value
starts to be reduced, if temperature increases above this value.
This has the net effect of increasing fan speed to cool down the
system. An interrupt can be generated when the temperature
rises above the high limit.
Programming High and Low Limits
There are six limit registers; a high limit and low limit are
associated with each temperature channel. These 8-bit registers
allow the high and low limit temperatures to be programmed
with 1°C resolution.
Temperature Limit Registers
Reg. 0x4E, Remote 1 Temperature Low Limit = 0x01
Reg. 0x4F, Remote 1 Temperature High Limit = 0x7F
Reg. 0x50, Local Temperature Low Limit = 0x01
Reg. 0x51, Local Temperature High Limit = 0x7F
However, the loop operation is not as simple as described in
these steps. A number of conditions govern the situations in
which TMIN can increase or decrease.
Short Cycle and Long Cycle
The ADT7468 implements two loops: a short cycle and a long
cycle. The short cycle takes place every n monitoring cycles. The
long cycle takes place every 2n monitoring cycles. The value of
n is programmable for each temperature channel. The bits are
located at the following register locations:
Remote 1 = CYR1 = Bits <2:0> of Calibration Control
Register 2 (Address = 0x37).
Reg. 0x52, Remote 2 Temperature Low Limit = 0x01
Reg. 0x53, Remote 2 Temperature High Limit = 0x7F
Rev. 0 | Page 52 of 80
ADT7468
WAIT 2n
MONITORING
CYCLES
Remote 2 = CYR2 = Bits <7:6> of Calibration Control Register
2 and Bit 0 of Calibration Control Register 1 (Address = 0x36).
CURRENT
TEMPERATURE
MEASUREMENT
T1(n)
Table 15. Cycle Bit Assignments
OPERATING
POINT
TEMPERATURE
OP1
Short Cycle
8 cycles
16 cycles
32 cycles
64 cycles
128 cycles
256 cycles
512 cycles
1024 cycles
(1 s)
(2 s)
(4 s)
(8 s)
(16 s)
(32 s)
(64 s)
(128 s)
Long Cycle
16 cycles
32 cycles
64 cycles
128 cycles
256 cycles
512 cycles
1024 cycles
2048 cycles
(2 s)
(4 s)
(8 s)
(16 s)
(32 s)
(64 s)
(128 s)
(256 s)
NO
PREVIOUS
TEMPERATURE
MEASUREMENT
T1 (n – 1)
HIGH TEMP
LIMIT
OPERATING
POINT
ACTUAL
TEMP
LOW TEMP
LIMIT
Figure 73. Temperature between Operating Point and Low Temperature Limit
NO
Because neither the operating point minus the hysteresis
temperature nor the low temperature limit has been exceeded,
the TMIN value is not adjusted, and the fan runs at a speed
determined by the fixed TMIN and TRANGE values defined in the
automatic fan speed control mode.
DO NOTHING
DO NOTHING
(SYSTEM IS
COOLING OF
FOR CONSTANT)
YES
Example: Operating Point Exceeded—TMIN Reduced
When the measured temperature is below the operating point
temperature minus the hysteresis, TMIN remains the same.
NO
DECREASE TMIN BY 1°C
04499-0-077
IS T1(n) – T1(n – 1) = 0.5 – 0.75°C
IS T1(n) – T1(n – 1) = 1.0 – 1.75°C
IS T1(n) – T1(n – 1) > 2.0°C
DECREASE TMIN BY 2°C
DECREASE TMIN BY 4°C
Figure 71. Short Cycle Steps
Figure 72 shows the steps taken during the long cycle.
The following examples illustrate some of the circumstances
that might cause TMIN to increase, decrease, or stay the same.
Example: Normal Operation—No TMIN Adjustment
1.
2.
HYSTERESIS
TMIN
YES
IS T1(n) – T1(n – 1)
≤ 0.25°C
DO NOT
CHANGE
Figure 72. Long Cycle Steps
WAIT n
MONITORING
CYCLES
IS T1(n) >
(OP1 – HYS)
INCREASE
TMIN BY 1°C
THERM LIMIT
Figure 71 shows the steps taken during the short cycle.
OPERATING
POINT
TEMPERATURE
OP1
DECREASE TMIN
BY 1°C
NO
IS T1(n) < LOW TEMP LIMIT
AND
TMIN < HIGH TEMP LIMIT YES
AND
TMIN < OP1
AND
T1(n) > TMIN
Care should be taken when choosing the cycle time. A long
cycle time means that TMIN is updated less often. If your system
has very fast temperature transients, the dynamic TMIN control
loop will always be lagging. If you choose a cycle time that is too
fast, the full benefit of changing TMIN might not be realized and
needs to change again on the next cycle; in effect, it is overshooting. It is necessary to carry out some calibration to identify
the most suitable response time.
CURRENT
TEMPERATURE
MEASUREMENT
T1(n)
YES
04499-0-079
Code
000
001
010
011
100
101
110
111
IS T1(n) > OP1
04499-0-078
Local = CYL = Bits <5:3> of Calibration Control Register 2
(Address = 0x37).
If measured temperature never exceeds the programmed
operating point minus the hysteresis temperature, then
TMIN is not adjusted, that is, remains at its current setting.
If measured temperature never drops below the low
temperature limit, then TMIN is not adjusted.
Once the temperature exceeds the operating temperature minus
the hysteresis (OP − Hyst), TMIN starts to decrease. This occurs
during the short cycle (see Figure 71). The rate at which TMIN
decreases depends on the programmed value of n. It also
depends on how much the temperature has increased between
this monitoring cycle and the last monitoring cycle, that is, if
the temperature has increased by 1°C, then TMIN is reduced by
2°C. Decreasing TMIN has the effect of increasing the fan speed,
thus providing more cooling to the system.
If the temperature is slowly increasing only in the range
(OP − Hyst), that is, ≤0.25°C per short monitoring cycle, then
TMIN does not decrease. This allows small changes in
temperature in the desired operating zone without changing
TMIN. The long cycle makes no change to TMIN in the
Rev. 0 | Page 53 of 80
ADT7468
temperature range (OP − Hyst), because the temperature has
not exceeded the operating temperature.
Once the temperature exceeds the operating temperature, the
long cycle causes TMIN to be reduced by 1°C every long cycle
while the temperature remains above the operating temperature.
This takes place in addition to the decrease in TMIN that would
occur due to the short cycle. In Figure 74, because the temperature is increasing at a rate ≤0.25°C per short cycle, no reduction
in TMIN takes place during the short cycle.
Once the temperature has fallen below the operating
temperature, TMIN stays the same. Even when the temperature
starts to increase slowly, TMIN stays the same, because the
temperature increases at a rate ≤0.25°C per cycle.
conditions and the reasons they need to be true.
TMIN can increase, if
•
The measured temperature has fallen below the low
temperature limit. This means the user must choose the
low limit carefully. It should not be so low that the
temperature never falls below it, because TMIN would never
increase and the fans would run faster than necessary.
•
TMIN is below the high temperature limit. TMIN is never
allowed to increase above the high temperature limit. As a
result, the high limit should be sensibly chosen, because it
determines how high TMIN can go.
•
TMIN is below the operating point temperature. TMIN should
never be allowed to increase above the operating point
temperature, because the fans would not switch on until
the temperature rose above the operating point.
•
The temperature is above TMIN. The dynamic TMIN control
is turned off below TMIN.
Example: Increase TMIN Cycle
When the temperature drops below the low temperature limit,
TMIN can increase in the long cycle. Increasing TMIN has the
effect of running the fan slower and, therefore, quieter. The long
cycle diagram in Figure 74 shows the conditions that need to be
true for TMIN to increase. Here is a quick summary of those
THERM
LIMIT
HIGH TEMP
LIMIT
OPERATING
POINT
HYSTERESIS
ACTUAL
TEMP
NO CHANGE IN TMIN HERE
DUE TO ANY CYCLE, BECAUSE
T1(n) – T1 (n – 1) ≤ 0.25°C
AND T1(n) < OP = > TMIN
STAYS THE SAME
TMIN
DECREASE HERE DUE TO
SHORT CYCLE ONLY
T1(n) – T1 (n – 1) = 0.5°C
OR 0.75°C = > TMIN
DECREASES BY 1°C
EVERY SHORT CYCLE
DECREASE HERE DUE TO
LONG CYCLE ONLY
T1(n) – T1 (n – 1) ≤ 0.25°C
AND T1(n) > OP = > TMIN
DECREASES BY 1°C
EVERY LONG CYCLE
Figure 74. Effect of Exceeding Operating Point Minus Hysteresis Temperature
Rev. 0 | Page 54 of 80
04499-0-080
LOW TEMP
LIMIT
ADT7468
Figure 75 shows how TMIN increases when the current temperature is above TMIN and below the low temperature limit, and
TMIN is below the high temperature limit and below the
operating point. Once the temperature rises above the low
temperature limit, TMIN stays the same.
THERM
LIMIT
HIGH TEMP
LIMIT
LOW TEMP
LIMIT
HYSTERESIS
TMIN
Bits <4:2> of dynamic TMIN control Register 1 (Reg. 0x36)
enable/disable THERM monitoring to program the operating
point.
Dynamic TMIN Control Register 1 (0x36)
Figure 75. Increasing TMIN for Quieter Operation
Example: Preventing TMIN from Reaching Full Scale
Because TMIN is dynamically adjusted, it is undesirable for TMIN
to reach full scale (127°C), because the fan would never switch
on. As a result, TMIN is allowed to vary only within a specified
range:
1.
The lowest possible value for TMIN is –127°C (twos
complement mode) or −64°C (Offset 64 mode).
2.
TMIN cannot exceed the high temperature limit.
3.
If the temperature is below TMIN, the fan is switched off or
is running at minimum speed, and dynamic TMIN control is
disabled.
<3> PHTL = 1, copies the local current temperature to the local
temperature operating point register, if THERM is asserted. The
operating point contains the temperature at which THERM is
asserted. This allows the system to run as quietly as possible
without affecting system performance.
<4> PHTR1 = 1, copies the Remote 1 current temperature to
the Remote 1 operating point register, if THERM is asserted.
The operating point contains the temperature at which THERM
is asserted. This allows the system to run as quietly as possible
without affecting system performance.
ACTUAL
TEMP
HIGH TEMP
LIMIT
TMIN
PHTR2 = 0, ignores any THERM assertions. The Remote 2
operating point register reflects its programmed value.
HYSTERESIS
TMIN PREVENTED
FROM INCREASING
04499-0-082
LOW TEMP
LIMIT
<2> PHTR2 = 1, copies the Remote 2 current temperature to
the Remote 2 operating point register, if THERM is asserted.
The operating point contains the temperature at which THERM
is asserted. This allows the system to run as quietly as possible
without affecting system performance.
PHTL = 0, ignores any THERM assertions. The local
temperature operating point register reflects its programmed
value.
THERM
LIMIT
OPERATING
POINT
The operating point for the processor can be determined by
allowing the current temperature to be copied to the operating
point register when the PROCHOT output pulls the THERM
input low on the ADT7468. This gives the maximum
temperature at which the Pentium 4 can run before clock
modulation occurs.
Enabling the THERM Trip Point as the Operating Point
ACTUAL
TEMP
04499-0-081
OPERATING
POINT
The optimal operating point for the processor is determined by
monitoring the thermal monitor in the Intel Pentium 4 processor. To do this, the PROCHOT output of the Pentium 4 is
connected to the THERM input of the ADT7468.
PHTR1 = 0, ignores any THERM assertions. The Remote 1
operating point register reflects its programmed value.
Figure 76. TMIN Adjustments Limited by the High Temperature Limit
Enabling Dynamic TMIN Control Mode
STEP 11: MONITORING THERM
Using the operating point limit ensures that the dynamic TMIN
control mode is operating in the best possible acoustic position
while ensuring that the temperature never exceeds the maximum operating temperature. Using the operating point limit
allows TMIN to be independent of system-level issues because of
its self-corrective nature. In PC design, the operating point for
the chassis is usually the worst-case internal chassis
temperature.
Bits <7:5> of dynamic TMIN control Register 1 (Reg. 0x36)
enable/disable dynamic TMIN control on the temperature
channels.
Dynamic TMIN Control Register 1 (0x36)
<5> R2T = 1, enables dynamic TMIN control on the Remote 2
temperature channel. The chosen TMIN value is dynamically
adjusted based on the current temperature, operating point, and
high and low limits for this zone.
Rev. 0 | Page 55 of 80
ADT7468
R2T = 0, disables dynamic TMIN control. The TMIN value chosen
is not adjusted and the channel behaves as described in the
Automatic Fan Control Overview section.
<6> LT = 1, enables dynamic TMIN control on the local
temperature channel. The chosen TMIN value is dynamically
adjusted based on the current temperature, operating point, and
high and low limits for this zone.
LT = 0, disables dynamic TMIN control. The TMIN value chosen is
not adjusted and the channel behaves as described in the
Automatic Fan Control Overview section.
<7> R1T = 1, enables dynamic TMIN control on the Remote 1
temperature channel. The chosen TMIN value is dynamically
adjusted based on the current temperature, operating point, and
high and low limits for this zone.
R1T = 0, disables dynamic TMIN control. The TMIN value chosen
is not adjusted and the channel behaves as described in the
Automatic Fan Control Overview section.
ENHANCING SYSTEM ACOUSTICS
Automatic fan speed control mode reacts instantaneously to
changes in temperature, that is, the PWM duty cycle responds
immediately to temperature change. Any impulses in
temperature can cause an impulse in fan noise. For psychoacoustic reasons, the ADT7468 can prevent the PWM output
from reacting instantaneously to temperature changes.
Enhanced acoustic mode controls the maximum change in
PWM duty cycle at a given time. The objective is to prevent the
fan from cycling up and down, annoying the user.
Acoustic Enhancement Mode Overview
Figure 77 gives a top-level overview of the automatic fan control
circuitry on the ADT7468 and shows where acoustic
enhancement fits in. Acoustic enhancement is intended as a
postdesign tweak made by a system or mechanical engineer
evaluating best settings for the system. Having determined the
optimal settings for the thermal solution, the engineer can
adjust the system acoustics. The goal is to implement a system
that is acoustically pleasing without causing user annoyance due
to fan cycling. It is important to realize that although a system
might pass an acoustic noise requirement specification (for
example, 36 dB), if the fan is annoying, it fails the consumer test.
ACOUSTIC
ENHANCEMENT
PWM
MIN
100%
PWM
CONFIG
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TMIN
REMOTE 2 =
CPU TEMP
TRANGE
THERMAL CALIBRATION
PWM
MIN
100%
LOCAL =
VRM TEMP
TRANGE
THERMAL CALIBRATION
TMIN
TACHOMETER 1
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
0%
PWM
MIN
100%
TRANGE
PWM1
0%
MUX
TMIN
PWM
GENERATOR
TACHOMETER 2
MEASUREMENT
RAMP
CONTROL
(ACOUSTIC
ENHANCEMENT)
TACHOMETER 3
AND 4
MEASUREMENT
0%
TACH1
PWM
CONFIG
PWM
GENERATOR
CPU FAN SINK
PWM2
TACH2
PWM
CONFIG
FRONT CHASSIS
PWM
GENERATOR
PWM3
TACH3
REMOTE 1 =
AMBIENT TEMP
REAR CHASSIS
Figure 77. Acoustic Enhancement Smoothes Fan Speed Variations under Automatic Fan Speed Control
Rev. 0 | Page 56 of 80
04499-0-083
THERMAL CALIBRATION
ADT7468
The temperature-centric approach involves smoothing transient
temperatures as they are measured by a temperature source (for
example, Remote 1 temperature). The temperature values used
to calculate the PWM duty cycle values are smoothed, reducing
fan speed variation. However, this approach causes an inherent
delay in updating fan speed and causes the thermal characteristics of the system to change. It also causes the system fans to
stay on longer than necessary, because the fan’s reaction is
merely delayed. The user has no control over noise from
different fans driven by the same temperature source. Consider,
for example, a system in which control of a CPU cooler fan (on
PWM1) and a chassis fan (on PWM2) use Remote 1 temperature. Because the Remote 1 temperature is smoothed, both fans
are updated at exactly the same rate. If the chassis fan is much
louder than the CPU fan, there is no way to improve its
acoustics without changing the thermal solution of the CPU
cooling fan.
The fan-centric approach to system acoustic enhancement
controls the PWM duty cycle, driving the fan at a fixed rate (for
example, 6%). Each time the PWM duty cycle is updated, it is
incremented by a fixed 6%. As a result, the fan ramps smoothly
to its newly calculated speed. If the temperature starts to drop,
the PWM duty cycle immediately decreases by 6% at every
update. Therefore, the fan ramps smoothly up or down without
inherent system delay. Consider, for example, controlling the
same CPU cooler fan (on PWM1) and chassis fan (on PWM2)
using Remote 1 temperature. The TMIN and TRANGE settings have
already been defined in automatic fan speed control mode, that
is, thermal characterization of the control loop has been
optimized. Now the chassis fan is noisier than the CPU cooling
fan. Using the fan-centric approach, PWM2 can be placed into
acoustic enhancement mode independently of PWM1. The
acoustics of the chassis fan can, therefore, be adjusted without
affecting the acoustic behavior of the CPU cooling fan, even
though both fans are controlled by Remote 1 temperature. The
fan-centric approach is how acoustic enhancement works on
the ADT7468.
Enabling Acoustic Enhancement for Each PWM Output
Enhance Acoustics Register 1 (Reg. 0x62)
<3> = 1, enables acoustic enhancement on PWM1 output.
Enhance Acoustics Register 2 (Reg. 0x63)
<7> = 1, enables acoustic enhancement on PWM2 output.
<3> = 1, enables acoustic enhancement on PWM3 output.
Effect of Ramp Rate on Enhanced Acoustics Mode
The PWM signal driving the fan has a period, T, given by the
PWM drive frequency, f, because T = 1/f. For a given PWM
PWM_OUT
33% DUTY
CYCLE
85
TIME SLOTS
170
TIME SLOTS
04499-0-084
There are two different approaches to implementing system
acoustic enhancement: temperature-centric and fan-centric.
period, T, the PWM period is subdivided into 255 equal time
slots. One time slot corresponds to the smallest possible
increment in the PWM duty cycle. A PWM signal of 33% duty
cycle is, therefore, high for 1/3 × 255 time slots and low for 2/3
× 255 time slots. Therefore, a 33% PWM duty cycle corresponds
to a signal that is high for 85 time slots and low for 170 time
slots.
PWM OUTPUT
(ONE PERIOD)
= 255 TIME SLOTS
Figure 78. 33% PWM Duty Cycle Represented in Time Slots
The ramp rates in the enhanced acoustics mode are selectable
from the values 1, 2, 3, 5, 8, 12, 24, and 48. The ramp rates are
discrete time slots. For example, if the ramp rate is 8, then eight
time slots are added to the PWM high duty cycle each time the
PWM duty cycle needs to be increased. If the PWM duty cycle
value needs to be decreased, it is decreased by eight time slots.
Figure 79 shows how the enhanced acoustics mode algorithm
operates.
READ
TEMPERATURE
CALCULATE
NEW PWM
DUTY CYCLE
IS NEW PWM
VALUE >
PREVIOUS
VALUE?
NO
DECREMENT
PREVIOUS
PWM VALUE
BY RAMP RATE
YES
INCREMENT
PREVIOUS
PWM VALUE
BY RAMP RATE
04499-0-085
Approaches to System Acoustic Enhancement
Figure 79. Enhanced Acoustics Algorithm
The enhanced acoustics mode algorithm calculates a new PWM
duty cycle based on the temperature measured. If the new
PWM duty cycle value is greater than the previous PWM value,
then the previous PWM duty cycle value is incremented by
either 1, 2, 3, 5, 8, 12, 24, or 48 time slots, depending on the
settings of the enhance acoustics registers. If the new PWM
duty cycle value is less than the previous PWM value, then the
previous PWM duty cycle is decremented by 1, 2, 3, 5, 8, 12, 24,
or 48 time slots. Each time the PWM duty cycle is incremented
or decremented, its value is stored as the previous PWM duty
cycle for the next comparison.
A ramp rate of 1 corresponds to one time slot, which is 1/255 of
the PWM period. In enhanced acoustics mode, incrementing or
decrementing by 1 changes the PWM output by 1/255 × 100%.
Rev. 0 | Page 57 of 80
ADT7468
STEP 12: RAMP RATE FOR ACOUSTIC
ENHANCEMENT
The optimal ramp rate for acoustic enhancement can be found
through system characterization after the thermal optimization
has been finished. The effect of each ramp rate should be
logged, if possible, to determine the best setting for a given
solution.
temperature reading is available every 115 ms. With these
settings, it takes approximately 0.76 s to go from 33% duty cycle
to 100% duty cycle (full speed). Even though the temperature
increases very rapidly, the fan ramps up to full speed gradually.
140
120
RTEMP (°C)
120
100
100
Enhanced Acoustics Register 1 (Reg. 0x62)
80
<2:0> ACOU, selects the ramp rate for PWM1.
80
000 = 1 time slot = 35 s
001 = 2 time slots = 17.6 s
010 = 3 time slots = 11.8 s
011 = 5 time slots = 7 s
100 = 8 time slots = 4.4 s
101 = 12 time slots =3 s
110 = 24 time slots = 1.6 s
111 = 48 time slots = 0.8 s
Enhance Acoustics Register 2 (Reg. 0x63)
60
60
PWM CYCLE (%)
40
40
0
0
0
0.76
TIME (s)
04499-0-086
20
20
Figure 80. Enhanced Acoustics Mode with Ramp Rate = 48
Figure 81 shows how changing the ramp rate from 48 to 8
affects the control loop. The overall response of the fan is
slower. Because the ramp rate is reduced, it takes longer for the
fan to achieve full running speed. In this case, it takes
approximately 4.4 s for the fan to reach full speed.
<2:0> ACOU3, selects the ramp rate for PWM3.
000 = 1 time slot = 35 s
001 = 2 time slots = 17.6 s
010 = 3 time slots = 11.8 s
011 = 5 time slots = 7 s
100 = 8 time slots = 4.4 s
101 = 12 time slots = 3 s
110 = 24 time slots = 1.6 s
111 = 48 time slots = 0.8 s
120
140
RTEMP (°C)
120
100
100
80
PWM DUTY CYCLE (%)
80
60
60
40
40
20
000 = 1 time slot = 35 s
001 = 2 time slots = 17.6 s
010 = 3 time slots = 11.8 s
011 = 5 time slots = 7 s
100 = 8 time slots = 4.4 s
101 = 12 time slots = 3 s
110 = 24 time slots = 1.6 s
111 = 48 time slots = 0.8 s
20
0
0
4.4
TIME (s)
0
04499-0-087
<6:4> ACOU2, selects the ramp rate for PWM2.
Figure 81. Enhanced Acoustics Mode with Ramp Rate = 8
Figure 82 shows the PWM output response for a ramp rate of 2.
In this instance, the fan took about 17.6 s to reach full running
speed.
140
120
RTEMP (°C)
120
100
100
80
80
PWM DUTY CYCLE (%)
40
40
20
20
Figure 80 shows remote temperature plotted against PWM duty
cycle for enhanced acoustics mode. The ramp rate is set to 48,
which corresponds to the fastest ramp rate. Assume that a new
60
60
0
0
TIME (s)
17.6
0
Figure 82. Enhanced Acoustics Mode with Ramp Rate = 2
Rev. 0 | Page 58 of 80
04499-0-088
Another way to view the ramp rates is to measure the time it
takes for the PWM output to ramp up from 0% to 100% duty
cycle for an instantaneous change in temperature. This can be
tested by putting the ADT7468 into manual mode and changing
the PWM output from 0% to 100% PWM duty cycle. The PWM
output takes 35 s to reach 100%, when a ramp rate of 1 time slot
is selected.
ADT7468
Figure 83 shows how the control loop reacts to temperature
with the slowest ramp rate. The ramp rate is set to 1, while all
other control parameters remain the same. With the slowest
ramp rate selected, it takes 35 s for the fan to reach full speed.
PWM1 Configuration Register (Reg. 0x5C)
<3> SLOW, 1 slows the ramp rate for PWM1 by 4.
PWM2 Configuration Register (Reg. 0x5D)
<3> SLOW, 1 slows the ramp rate for PWM2 by 4.
140
120
PWM3 Configuration Register (Reg. 0x5E)
RTEMP (°C)
120
100
<3> SLOW, 1 slows the ramp rate for PWM3 by 4.
100
The following sections list the ramp-up times when the SLOW
bit is set for each PWM output.
80
80
60
PWM DUTY CYCLE (%)
60
Enhanced Acoustics Register 1 (Reg. 0x62)
40
<2:0> ACOU, selects the ramp rate for PWM1.
40
20
0
04499-0-089
20
0
0
35
TIME (s)
Figure 83. Enhanced Acoustics Mode with Ramp Rate = 1
As Figure 80 to Figure 83 show, the rate at which the fan reacts
to temperature change is dependent on the ramp rate selected in
the enhanced acoustics registers. The higher the ramp rate, the
faster the fan reaches the newly calculated fan speed.
Figure 84 shows the behavior of the PWM output as temperature varies. As the temperature increases, the fan speed ramps
up. Small drops in temperature do not affect the ramp-up
function, because the newly calculated fan speed is still higher
than the previous PWM value. Enhanced acoustics mode allows
the PWM output to be made less sensitive to temperature
variations. This is dependent on the ramp rate selected and
programmed into the enhanced acoustics registers.
000 = 140 s
001 = 70.4 s
010 = 47.2 s
011 = 28 s
100 = 17.6 s
101 = 12 s
110 = 6.4 s
111 = 3.2 s
Enhance Acoustics Register 2 (Reg. 0x63)
<2:0> ACOU3, selects the ramp rate for PWM3.
000 = 140 s
001 = 70.4 s
010 = 47.2 s
011 = 28 s
100 = 17.6 s
101 = 12 s
110 = 6.4 s
111 = 3.2 s
90
80
70
PWM DUTY CYCLE (%)
<6:4> ACOU2, selects the ramp rate for PWM2.
60
000 = 140 s
001 = 70.4 s
010 = 47.2 s
011 = 28 s
100 = 17.6 s
101 = 12 s
110 = 6.4 s
111 = 3.2 s
50
RTEMP (°C)
40
30
04499-0-090
20
10
0
Figure 84. How Fan Reacts to Temperature Variation
in Enhanced Acoustics Mode
Slower Ramp Rates
The ADT7468 can be programmed for much longer ramp times
by slowing the ramp rates. Each ramp rate can be slowed by a
factor of 4.
Rev. 0 | Page 59 of 80
ADT7468
REGISTER TABLES
Table 16. ADT7468 Registers
Address
0x20
0x21
0x22
0x23
0x24
0x25
R/W
R
R
R
R
R
R
0x26
0x27
R
R
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x30
R
R
R
R
R
R
R
R
R/W
0x31
R/W
0x32
R/W
0x33
R/W
0x34
R/W
0x35
R/W
0x36
R/W
0x37
R/W
0x38
R/W
0x39
R/W
0x3A
R/W
0x3D
0x3E
R
R
0x3F
0x40
R
R/W
Description
2.5 V measurement
VCCP measurement
VCC measurement
5 V measurement
12 V measurement
Remote 1
Temperature
Local Temperature
Remote 2
Temperature
TACH1 Low Byte
TACH1 High Byte
TACH2 Low Byte
TACH2 High Byte
TACH3 Low Byte
TACH3 High Byte
TACH4 Low Byte
TACH4 High Byte
PWM1 Current Duty
Cycle
PWM2 Current Duty
Cycle
PWM3 Current Duty
Cycle
Remote 1
Operating Point
Local Temp
Operating Point
Remote 2
Operating Point
Dynamic TMIN
Control Reg. 1
Dynamic TMIN
Control Reg. 2
Max PWM 1 Duty
Cycle
Max PWM 2 Duty
Cycle
Max PWM 3 Duty
Cycle
Device ID Register
Company ID
Number
Revision Number
Configuration 1
Bit 7
9
9
9
9
9
9
Bit 6
8
8
8
8
8
8
Bit 5
7
7
7
7
7
7
Bit 4
6
6
6
6
6
6
Bit 3
5
5
5
5
5
5
Bit 2
4
4
4
4
4
4
Bit 1
3
3
3
3
3
3
Bit 0
2
2
2
2
2
2
Default
0x00
0x00
0x00
0x00
0x00
0x01
0x41
R
Interrupt Status 1
0x42
R
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
0x01
0x01
7
15
7
15
7
15
7
15
7
6
14
6
14
6
14
6
14
6
5
13
5
13
5
13
5
13
5
4
12
4
12
4
12
4
12
4
3
11
3
11
3
11
3
11
3
2
10
2
10
2
10
2
10
2
1
9
1
9
1
9
1
9
1
0
8
0
8
0
8
0
8
0
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
7
6
5
4
3
2
1
0
0x00
7
6
5
4
3
2
1
0
0x00
7
6
5
4
3
2
1
0
0xA4
Yes
7
6
5
4
3
2
1
0
0xA4
Yes
7
6
5
4
3
2
1
0
0xA4
Yes
R2T
LT
R1T
PHTR2
PHTL
PHTR1
VCCPLO
CYR2
0x00
Yes
CYR2
CYR2
CYL
CYL
CYL
CYR1
CYR1
CYR1
0x00
Yes
7
6
5
4
3
2
1
0
0xFF
Yes
7
6
5
4
3
2
1
0
0xFF
Yes
7
6
5
4
3
2
1
0
0xFF
Yes
7
7
6
6
5
5
4
4
3
3
2
2
1
1
0
0
0x68
0x41
VER
VCC =
5V
OOL
VER
TODIS
VER
FSPDIS
VER
VxI
STP
FSPD
STP
RDY
STP
LOCK
STP
STRT
0x70
0x01
R2T
LT
R1T
VCC
VCCP
2.5 V
0x00
Interrupt Status 2
D2
FAULT
D1
FAULT
FAN4/
THERM
FAN3
5 V/THERM
Timer Limit
FAN2
FAN1
12 V/VC
0x00
VID Config
2.5 V Low Limit
2.5 V High Limit
VCCP Low Limit
VCCP High Limit
VCC Low Limit
VCC High Limit
5 V Low Limit
VIDSEL
7
7
7
7
7
7
7
THLD
6
6
6
6
6
6
6
VID 5
5
5
5
5
5
5
5
VID 4
4
4
4
4
4
4
4
VID 3
3
3
3
3
3
3
3
VID 2
2
2
2
2
2
2
2
THERM
Temp
Limit
VID 1
1
1
1
1
1
1
1
VID 0
0
0
0
0
0
0
0
0x00
0x00
0xFF
0x00
0xFF
0x00
0xFF
0x00
Rev. 0 | Page 60 of 80
Lockable?
Yes
ADT7468
Address
0x4B
0x4C
0x4D
0x4E
R/W
R/W
R/W
R/W
R/W
0x4F
R/W
0x50
R/W
0x51
R/W
0x52
R/W
0x53
R/W
0x54
R/W
0x55
R/W
0x56
R/W
0x57
R/W
0x58
R/W
0x59
R/W
0x5A
R/W
0x5B
R/W
0x5C
R/W
0x5D
R/W
0x5E
R/W
0x5F
R/W
0x60
R/W
0x61
R/W
0x62
R/W
0x63
R/W
0x64
R/W
0x65
R/W
0x66
R/W
0x67
0x68
0x69
0x6A
R/W
R/W
R/W
R/W
0x6B
R/W
Description
5 V High Limit
12 V Low Limit
12 V High Limit
Remote 1 Temp
Low Limit
Remote 1 Temp
High Limit
Local Temp Low
Limit
Local Temp High
Limit
Remote 2 Temp
Low Limit
Remote 2 Temp
High Limit
TACH1 Minimum
Low Byte
TACH1 Minimum
High Byte
TACH2 Minimum
Low Byte
TACH2 Minimum
High Byte
TACH3 Minimum
Low Byte
TACH3 Minimum
High Byte
TACH4 Minimum
Low Byte
TACH4 Minimum
High Byte
PWM1
Configuration
Register
PWM2
Configuration
Register
PWM3
Configuration
Register
Remote 1
TRANGE/PWM 1
Frequency
Local TRANGE/PWM 2
Frequency
Remote 2
TRANGE/PWM3
Frequency
Enhance Acoustics
Reg. 1
Enhance Acoustics
Reg. 2
PWM1 Min Duty
Cycle
PWM2 Min Duty
Cycle
PWM3 Min Duty
Cycle
Remote 1 Temp TMIN
Local Temp TMIN
Remote 2 Temp TMIN
Remote 1 THERM
Temp Limit
Local THERM Temp
Limit
Bit 7
7
7
7
7
Bit 6
6
6
6
6
Bit 5
5
5
5
5
Bit 4
4
4
4
4
Bit 3
3
3
3
3
Bit 2
2
2
2
2
Bit 1
1
1
1
1
Bit 0
0
0
0
0
Default
0xFF
0x00
0xFF
0x01
7
6
5
4
3
2
1
0
0x7F
7
6
5
4
3
2
1
0
0x01
7
6
5
4
3
2
1
0
0x7F
7
6
5
4
3
2
1
0
0x01
7
6
5
4
3
2
1
0
0x7F
7
6
5
4
3
2
1
0
0xFF
15
14
13
12
11
10
9
8
0xFF
7
6
5
4
3
2
1
0
0xFF
15
14
13
12
11
10
9
8
0xFF
7
6
5
4
3
2
1
0
0xFF
15
14
13
12
11
10
9
8
0xFF
7
6
5
4
3
2
1
0
0xFF
15
14
13
12
11
10
9
8
0xFF
BHVR
BHVR
BHVR
INV
SLOW
SPIN
SPIN
SPIN
0x82
Yes
BHVR
BHVR
BHVR
INV
SLOW
SPIN
SPIN
SPIN
0x82
Yes
BHVR
BHVR
BHVR
INV
SLOW
SPIN
SPIN
SPIN
0x82
Yes
RANGE
RANGE
RANGE
RANGE
THRM
FREQ
FREQ
FREQ
0XC4
Yes
RANGE
RANGE
RANGE
RANGE
THRM
FREQ
FREQ
FREQ
0XC4
Yes
RANGE
RANGE
RANGE
RANGE
THRM
FREQ
FREQ
FREQ
0XC4
Yes
MIN3
MIN2
MIN1
SYNC
EN1
ACOU
ACOU
ACOU
0X00
Yes
EN2
ACOU2
ACOU2
ACOU2
EN3
ACOU3
ACOU3
ACOU3
0X00
Yes
7
6
5
4
3
2
1
0
0X80
Yes
7
6
5
4
3
2
1
0
0X80
Yes
7
6
5
4
3
2
1
0
0X80
Yes
7
7
7
7
6
6
6
6
5
5
5
5
4
4
4
4
3
3
3
3
2
2
2
2
1
1
1
1
0
0
0
0
0X9A
0X9A
0X9A
0XA4
Yes
Yes
Yes
Yes
7
6
5
4
3
2
1
0
0XA4
Yes
Rev. 0 | Page 61 of 80
Lockable?
ADT7468
Address
0x6C
R/W
R/W
0x6D
R/W
0x6E
R/W
0x6F
R/W
0x70
R/W
0x71
R/W
0x72
R/W
0x73
R/W
0x74
R/W
0x75
R/W
0x76
R/W
0x77
R/W
0x78
R/W
0x79
R
0x7A
R/W
0x7B
R/W
0x7C
R/W
0x7D
R/W
0x7E
0x7F
R
R
Description
Remote 2 THERM
Temp Limit
Remote 1 and Local
Temp/TMIN
Hysteresis
Remote 2
Temp/TMIN
Hysteresis
XNOR Tree Test
Enable
Remote 1
Temperature Offset
Local Temperature
Offset
Remote 2
Temperature Offset
Configuration
Register 2
Interrupt Mask 1
Register
Interrupt Mask 2
Register
Extended
Resolution 1
Extended
Resolution 2
Configuration
Register 3
THERM Timer Status
Register
THERM Timer Limit
Register
TACH Pulses per
Revolution
Configuration
Register 5
Configuration
Register 4
Test Register 1
Test Register 2
Bit 7
7
Bit 6
6
Bit 5
5
Bit 4
4
Bit 3
3
Bit 2
2
Bit 1
1
Bit 0
0
Default
0XA4
Lockable?
Yes
HYSR1
HYSR1
HYSR1
HYSR1
HYSL
HYSL
HYSL
HYSL
0X44
Yes
HYSR2
HYSR2
HYSR2
HYRS
RES
RES
RES
RES
0X40
Yes
RES
RES
RES
RES
RES
RES
RES
XEN
0X00
Yes
7
6
5
4
3
2
1
0
0X00
Yes
7
6
5
4
3
2
1
0
0X00
Yes
7
6
5
4
3
2
1
0
0X00
Yes
SHDN
CONV
ATTN
AVG
AIN4
AIN3
AIN2
AIN1
0X00
Yes
OOL
R2T
LT
RIT
5V
VCC
VCCP
2.5 V
0X00
D2
D1
F4P
FAN3
FAN2
FAN1
OVT
12 V / VC
0X00
5V
5V
VCC
VCC
VCCP
VCCP
2.5 V
2.5 V
0X00
TDM2
TDM2
LTMP
LTMP
TDM1
TDM1
12 V
12 V
0X00
DC4
DC3
DC2
DC1
FAST
BOOST
THERM
0X00
TMR
TMR
TMR
TMR
TMR
TMR
TMR
ALERT
Enable
ASRT/TMRO
0X00
LIMT
LIMT
LIMT
LIMT
LIMT
LIMT
LIMT
LIMT
0X00
FAN4
FAN4
FAN3
FAN3
FAN2
FAN2
FAN1
FAN1
0X55
RES
RES
RES
RES
GPIOP
GPIOD
LF/HF
0X00
Yes
BpAtt
12 V
BpAtt
5V
BpAtt
VCCP
TWOS
COMPL
Pin 14 Func
0X00
Yes
0X00
0X00
Yes
Yes
AINL
AINL
BpAtt
2.5 V
DO NOT WRITE TO THESE REGISTERS
DO NOT WRITE TO THESE REGISTERS
Pin 14
Func
Yes
Table 17. Voltage Reading Registers (Power-On Default = 0x00)1
Register Address
0x20
0x21
0x22
0x23
0x24
R/W
Read-only
Read-only
Read-only
Read-only
Read-only
Description
Reflects the voltage measurement at the 2.5 V input on Pin 22 (8 MSBs of reading).
Reflects the voltage measurement2 at the VCCP input on Pin 23 (8 MSBs of reading).
Reflects the voltage measurement3 at the VCC input on Pin 4 (8 MSBs of reading).
Reflects the voltage measurement at the 5 V input on Pin 20 (8 MSBs of reading.
Reflects the voltage measurement at the 12 V input on Pin 21 (8 MSBs of reading).
1
If the extended resolution bits of these readings are also being read, the extended resolution registers (Reg. 0x76, 0x77) must be read first. Once the extended
resolution registers have been read, the associated MSB reading registers are frozen until read. Both the extended resolution registers and the MSB registers are frozen.
2
If VCCPLow (Bit 1 of the Dynamic TMIN Control Register 1, 0x36) is set, VCCP can control the sleep state of the ADT7468.
3
VCC (Pin 4) is the supply voltage for the ADT7468.
Rev. 0 | Page 62 of 80
ADT7468
Table 18. Temperature Reading Registers (Power-On Default = 0x01)1, 2, 3
Register Address
0x25
0x26
0x27
R/W
Read-only
Read-only
Read-only
Description
Remote 1 temperature reading3, 4 (8 MSB of reading).
Local temperature reading (8 MSB of reading).
Remote 2 temperature reading3, 4 (8 MSB of reading).
1
If the extended resolution bits of these readings are also being read, the extended resolution registers (Reg. 0x76, 0x77) must be read first. Once the extended
resolution registers have been read, all associated MSB reading registers are frozen until read. Both the extended resolution registers and the MSB registers are frozen.
2
These temperature readings can be in twos complement or Offset 64 format; this interpretation is determined by Bit 0 of Configuration Register 5 (0x7C).
3
In twos complement mode, a temperature reading of −128°C (0x80) indicates a diode fault (open or short) on that channel.
4
In Offset 64 mode, a temperature reading of −64°C (0x00) indicates a diode fault (open or short) on that channel.
Table 19. Fan Tachometer Reading Registers (Power-On Default = 0x00)1
Register Address
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
R/W
Read-only
Read-only
Read-only
Read-only
Read-only
Read-only
Read-only
Read-only
Description
TACH1 low byte.
TACH1 high byte.
TACH2 low byte.
TACH2 high byte.
TACH3 low byte.
TACH3 high byte.
TACH4 low byte.
TACH4 high byte.
1
These registers count the number of 11.11 µs periods (based on an internal 90 kHz clock) that occur between a number of consecutive fan TACH pulses (default = 2).
The number of TACH pulses used to count can be changed using the fan pulses per revolution register (Reg. 0x7B). This allows the fan speed to be accurately measured.
Because a valid fan tachometer reading requires that two bytes are read, the low byte must be read first. Both the low and high bytes are then frozen until read. At
power-on, these registers contain 0x0000 until such time as the first valid fan TACH measurement is read into these registers. This prevents false interrupts from
occurring while the fans are spinning up. A count of 0xFFFF indicates that a fan is one of the following:
•
Stalled or blocked (object jamming the fan).
•
Failed (internal circuitry destroyed).
•
Not populated. (The ADT7468 expects to see a fan connected to each TACH. If a fan is not connected to that TACH, its TACH minimum high and low bytes should
be set to 0xFFFF.)
•
Alternate function, for example, TACH4 reconfigured as THERM pin.
•
2-wire instead of 3-wire fan.
Table 20. Current PWM Duty Cycle Registers (Power-On Default = 0x00)1
Register Address
0x30
0x31
0x32
R/W
Read/write
Read/write
Read/write
Description
PWM1 current duty cycle (0% to 100% duty cycle = 0x00 to 0xFF).
PWM2 current duty cycle (0% to 100% duty cycle = 0x00 to 0xFF).
PWM3 current duty cycle (0% to 100% duty cycle = 0x00 to 0xFF).
1
These registers reflect the PWM duty cycle driving each fan at any given time. When in automatic fan speed control mode, the ADT7468 reports the PWM duty cycles
back through these registers. The PWM duty cycle values vary according to temperature in automatic fan speed control mode. During fan startup, these registers report
back 0x00. In software mode, the PWM duty cycle outputs can be set to any duty cycle value by writing to these registers.
Table 21. Operating Point Registers (Power-On Default = 0x64)1, 2, 3
Register Address
0x33
0x34
0x35
R/W3
Read/write
Read/write
Read/write
Description
Remote 1 operating point register (default = 100°C).
Local temperature operating point register (default = 100°C).
Remote 2 operating point register (default = 100°C).
1
These registers set the target operating point for each temperature channel when the dynamic TMIN control feature is enabled.
The fans being controlled are adjusted to maintain temperature about an operating point.
3
These registers become read-only when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to these registers fail.
2
Rev. 0 | Page 63 of 80
ADT7468
Table 22. Register 0x36—Dynamic TMIN Control Register 1 (Power-On Default = 0x00)1
Bit
<0>
Name
CYR2
R/W
Read/write
<1>
VCCPLO
Read/write
<2>
PHTR1
Read/write
<3>
PHTL
Read/write
<4>
PHTR2
Read/write
<5>
R1T
Read/write
<6>
LT
Read/write
<7>
R2T
Read/write
1
Description
MSB of 3-bit remote 2 cycle value. The other two bits of the code reside in Dynamic TMIN Control Register 2
(Reg. 0x37). These three bits define the delay time between making subsequent TMIN adjustments in the
control loop, in terms of the number of monitoring cycles. The system has associated thermal time constants
that need to be found to optimize the response of fans and the control loop.
VCCPLO = 1. When the power is supplied from 3.3 V STANDBY and the core voltage (VCCP) drops below its VCCP
low limit value (Reg. 0x46), the following occurs:
• Status Bit 1 in Status Register 1 is set.
• SMBALERT is generated, if enabled.
• PROCHOT monitoring is disabled.
• Dynamic TMIN control is disabled.
• The device is prevented from entering shutdown.
• Everything is re-enabled once VCCP increases above the VCCP low limit.
PHTR1 = 1 copies the Remote 1 current temperature to the Remote 1 operating point register, if THERM is
asserted. The operating point contains the temperature at which THERM is asserted, which allows the system
to run as quietly as possible without affecting system performance.
PHTR1 = 0 ignores any THERM assertions on the THERM pin. The Remote 1 operating point register reflects
its programmed value.
PHTL = 1 copies the local channel’s current temperature to the local operating point register, if THERM is
asserted. The operating point contains the temperature at which THERM is asserted, which allows the system
to run as quietly as possible without affecting system performance.
PHTL = 0 ignores any THERM assertions on the THERM pin. The local operating temperature point register
reflects its programmed value.
PHTR2 = 1 copies the Remote 2 current temperature to the Remote 2 operating point register, if THERM is
asserted. The operating point contains the temperature at which THERM is asserted. This allows the system to
run as quietly as possible without affecting system performance.
PHTR2 = 0 ignores any THERM assertions on the THERM pin. The Remote 2 operating point register reflects
its programmed value.
R1T = 1 enables dynamic TMIN control on the Remote 1 temperature channel. The chosen TMIN value is
dynamically adjusted based on the current temperature, operating point, and high and low limits for this
zone.
R1T = 0 disables dynamic TMIN control. The TMIN value chosen is not adjusted, and the channel behaves as
described in the Fan Speed Control section.
LT=1 enables dynamic TMIN control on the local temperature channel. The chosen TMIN value is dynamically
adjusted based on the current temperature, operating point, and high and low limits for this zone.
LT = 0 disables dynamic TMIN control. The TMIN value chosen is not adjusted, and the channel behaves as
described in the Fan Speed Control section.
R2T = 1 enables dynamic TMIN control on the Remote 2 temperature channel. The chosen TMIN value is
dynamically adjusted based on the current temperature, operating point, and high and low limits for this
zone.
R2T = 0 disables dynamic TMIN control. The TMIN value chosen is not adjusted, and the channel behaves as
described in the Fan Speed Control section.
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to this register fail.
Rev. 0 | Page 64 of 80
ADT7468
Table 23. Register 0x37—Dynamic TMIN Control Register 2 (Power-On Default = 0x00)1
Bit
<2:0>
<5:3>
<7:6>
Name
CYR1
R/W
Read/write
CYL
Bits
000
001
010
011
100
101
110
111
Read/write
CYR2
Bits
000
001
010
011
100
101
110
111
Read/write
Bits
000
001
010
011
100
101
110
111
Description
3-Bit Remote 1 Cycle Value. These three bits define the delay time between making subsequent TMIN
adjustments in the control loop for the Remote 1 channel, in terms of number of monitoring cycles. The
system has associated thermal time constants that need to be found to optimize the response of fans and
the control loop.
Decrease Cycle
Increase Cycle
8 cycles (1 s)
16 cycles (2 s)
16 cycles (2 s)
32 cycles (4 s)
32 cycles (4 s)
64 cycles (8 s)
64 cycles (8 s)
128 cycles (16 s)
128 cycles (16 s)
256 cycles (32 s)
256 cycles (32 s)
512 cycles (64 s)
512 cycles (64 s)
1024 cycles (128 s)
1024 cycles (128 s)
2048 cycles (256 s)
3-bit local temperature cycle value. These three bits define the delay time between making subsequent TMIN
adjustments in the control loop for the local temperature channel, in terms of number of monitoring cycles.
The system has associated thermal time constants that need to be found to optimize the response of fans
and the control loop.
Decrease Cycle
Increase Cycle
8 cycles (1 s)
16 cycles (2 s)
16 cycles (2 s)
32 cycles (4 s)
32 cycles (4 s)
64 cycles (8 s)
64 cycles (8 s)
128 cycles (16 s)
128 cycles (16 s)
256 cycles (32 s)
256 cycles (32 s)
512 cycles (64 s)
512 cycles (64 s)
1024 cycles (128 s)
1024 cycles (128 s)
2048 cycles (256 s)
2 LSBs of 3-bit Remote 2 cycle value. The MSB of the 3-bit code resides in Dynamic TMIN Control Register 1
(Reg. 0x36). These three bits define the delay time between making subsequent TMIN adjustments in the
control loop for the Remote 2 channel, in terms of number of monitoring cycles. The system has associated
thermal time constants that need to be found to optimize the response of fans and the control loop.
Decrease Cycle
8 cycles (1 s)
16 cycles (2 s)
32 cycles (4 s)
64 cycles (8 s)
128 cycles (16 s)
256 cycles (32 s s)
512 cycles (64 s)
1024 cycles (128 s)
Increase Cycle
16 cycles (2 s)
32 cycles (4 s)
64 cycles (8 s)
128 cycles (16 s)
256 cycles (32 s)
512 cycles (64 s)
1024 cycles (128 s)
2048 cycles (256 s)
1
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to this register fail.
Table 24. Maximim PWM Duty Cycle (Power-On Default = 0xFF)1, 2
Register Address
0x38
0x39
0x3A
1
2
R/W2
Read/write
Read/write
Read/write
Description
Maximum duty cycle for PWM1 output, default = 100% (0xFF.)
Maximum duty cycle for PWM2 output, default = 100% (0xFF).
Maximum duty cycle for PWM3 output, default = 100% (0xFF).
These registers set the maximum PWM duty cycle of the PWM output .
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to this register fail.
Rev. 0 | Page 65 of 80
ADT7468
Table 25. Register 0x40—Configuration Register 1 (Power-On Default = 0x01)
Bit
<0>
Name
STRT
R/W
Read/write
<1>
LOCK
Write once
<2>
RDY
Read-only
<3>
<4>
FSPD
VxI
Read/write
Read/write
<5>
FSPDIS
Read/write
<6>
TODIS
Read/write
<7>
VCC
Read/write
Description
Logic 1 enables monitoring and PWM control outputs based on the limit settings programmed.
Logic 0 disables monitoring and PWM control based on the default power-up limit settings.
Note that the limit values programmed are preserved even if a Logic 0 is written to this bit and the
default settings are enabled. This bit becomes read-only and cannot be changed once Bit 1 (LOCK bit)
has been written. All limit registers should be programmed by BIOS before setting this bit to 1.
(Lockable.)
Logic 1 locks all limit values to their current settings. Once this bit is set, all lockable registers become
read-only and cannot be modified until the ADT7468 is powered down and powered up again. This
prevents rogue programs such as viruses from modifying critical system limit settings. (Lockable.)
This bit is set to 1 by the ADT7468 to indicate only that the device is fully powered-up and ready to begin
system monitoring.
When set to 1, this bit runs all fans at full speed. Power-on default = 0. This bit never gets locked.
BIOS should set this bit to a 1 when the ADT7468 is configured to measure current from an ADI ADOPT™
VRM controller and to measure the CPU’s core voltage. This bit allows monitoring software to display
CPU watts usage. (Lockable.)
Logic 1 disables fan spin-up for two TACH pulses. Instead, the PWM outputs go high for the entire fan
spin-up timeout selected.
When this bit is set to 1, the SMBus timeout feature is enabled. This allows the ADT7468 to be used with
SMBus controllers that cannot handle SMBus timeouts. (Lockable.)
When this bit is set to 1, the ADT7468 rescales its VCC pin to measure 5 V supply. If this bit is 0, the
ADT7468 measures VCC as a 3.3 V supply. (Lockable.)
Table 26. Register 0x41—Interrupt Status Register 1 (Power-On Default = 0x00)
Bit
<0>
Name
2.5 V
R/W
Read-only
<1>
VCCP
Read-only
<2>
VCC
Read-only
<3>
Read-only
<4>
5 V/
THERM
timer
R1T
Read-only
<5>
LT
Read-only
<6>
R2T
Read-only
<7>
OOL
Read-only
Description
2.5 V = 1 indicates that the 2.5 V high or low limit has been exceeded. This bit is cleared on a read of the
status register only if the error condition has subsided.
VCCP = 1 indicates that the VCCP high or low limit has been exceeded. This bit is cleared on a read of the
status register only if the error condition has subsided.
VCC = 1 indicates that the VCC high or low limit has been exceeded. This bit is cleared on a read of the
status register only if the error condition has subsided.
A one indicates the 5 V high or low limit has been exceeded. This bit is cleared on a read of the status
register only if the error condition has subsided. If Pin 20 is configured as THERM, this bit is asserted when
the Timer Limit has been exceeded.
R1T = 1 indicates that the Remote 1 low or high temperature has been exceeded. This bit is cleared on a
read of the status register only if the error condition has subsided.
LT =1 indicates that the local low or high temperature has been exceeded. This bit is cleared on a read of
the status register only if the error condition has subsided.
R2T = 1 indicates that the Remote 2 low or high temperature has been exceeded. This bit is cleared on a
read of the status register only if the error condition has subsided.
OOL = 1 indicates that an out-of-limit event has been latched in Status Register 2. This bit is a logical OR
of all status bits in Status Register 2. Software can test this bit in isolation to determine whether any of
the voltage, temperature, or fan speed readings represented by Status Register 2 are out-of-limit, which
saves the need to read Status Register 2 during every interrupt or polling cycle.
Rev. 0 | Page 66 of 80
ADT7468
Table 27. Register 0x42—Interrupt Status Register 2 (Power-On Default = 0x00)
Bit
<0>
Name
12V/VC
R/W
Read-only
<1>
OVT
Read-only
<2>
FAN1
Read-only
<3>
FAN2
Read-only
<4>
FAN3
Read-only
<5>
F4P
Read-only
Read/write
Read-only
<6>
<7>
D1
D2
Read-only
Read-only
Description
A one indicates that the 12 V high or low limit has been exceeded. This bit is cleared on a read of the status
register only if the error condition has subsided. If Pin 21 is configured as VID5, this bit is the VID change bit.
This bit is set when the levels on VID0 to VID5 are different than they were 11 µs previously. This pin can be
used to generate an SMBALERT whenever the VID code changes.
OVT = 1 indicates that one of the THERM overtemperature limits has been exceeded. This bit is cleared on a
read of the status register when the temperature drops below THERM − THYST.
FAN1 = 1 indicates that Fan 1 has dropped below minimum speed or has stalled. This bit is not set when the
PWM 1 output is off.
FAN2 = 1 indicates that Fan 2 has dropped below minimum speed or has stalled. This bit is not set when the
PWM 2 output is off.
FAN3 = 1 indicates that Fan 3 has dropped below minimum speed or has stalled. This bit is not set when the
PWM 3 output is off.
When Pin 14 is programmed as a TACH4 input, F4P = 1 indicates that Fan 4 has dropped below minimum
speed or has stalled. This bit is not set when the PWM3 output is off.
When Pin 14 is programmed as a GPIO output, writing to this bit determines the logic output of the GPIO.
If Pin 14 is configured as the THERM timer input for THERM monitoring, then this bit is set when the THERM
assertion time exceeds the limit programmed in the THERM limit register (Reg. 0x7A).
D1 = 1 indicates either an open or short circuit on the Thermal Diode 1 inputs.
D2 = 1 indicates either an open or short circuit on the Thermal Diode 2 inputs.
Table 28. Register 43H—VID Register (Power-On Default = 0x00 )
Bit
<4:0>
Name
VID[4:0]
R/W
Read-only
<5>
VID5
Read-only
<6>
THLD
Read/write
<7>
VIDSEL
Read/write
Description
The VID[4:0] inputs from the CPU indicate the expected processor core voltage. On power-up, these bits
reflect the state of the VID pins, even if monitoring is not enabled.
Reads VID5 from the CPU when Bit 7 = 1. If Bit 7 = 0, then the VID5 bit always reads back 0 (power-on
default).
Selects the input switching threshold for the VID inputs.
THLD = 0 selects a threshold of 1 V (VOL < 0.8 V, VIH > 1.7 V).
THLD = 1 lowers the switching threshold to 0.6 V (VOL < 0.4 V, VIH > 0.8 V).
VIDSEL = 0 configures Pin 21 as the 12 V measurement input (default).
Table 29. Voltage Limit Registers1
Register Address
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
R/W
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Description2
2.5 V.
2.5 V.
VCCP low limit.
VCCP high limit.
VCC low limit.
VCC high limit.
5 V low limit.
5 V high limit.
12 V low limit.
12 V high limit.
1
Power-On Default
0x00
0xFF
0x00
0xFF
0x00
0xFF
0x00
0xFF
0x00
0xFF
Setting the Configuration Register 1 lock bit has no effect on these registers.
High Limits: An interrupt is generated when a value exceeds its high limit (> comparison). Low Limits: An interrupt is generated when a value is equal to or below its
low limit (≤ comparison).
2
Rev. 0 | Page 67 of 80
ADT7468
Table 30. Temperature Limit Registers1
Register Address
0x4E
0x4F
0x50
0x51
0x52
0x53
R/W
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Description2
Remote 1 temperature low limit.
Remote 1 temperature high limit.
Local temperature low limit.
Local temperature high limit.
Remote 2 temperature low limit.
Remote 2 temperature high limit.
Power-On Default
0x81
0x7F
0x81
0x7F
0x81
0x7F
1
Exceeding any of these temperature limits by 1°C causes the appropriate status bit to be set in the interrupt status register. Setting the Configuration Register 1 lock bit
has no effect on these registers.
2
High Limits: An interrupt is generated when a value exceeds its high limit (> comparison). Low Limits: An interrupt is generated when a value is equal to or below its
low limit (≤ comparison).
Table 31. Fan Tachometer Limit Registers1
Register Address
0x54
R/W
Read/write
0x55
Read/write
0x56
0x57
0x58
0x59
0x5A
0x5B
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Description
TACH1 minimum low byte.
TACH1 minimum high byte/Single channel ADC
channel select.
TACH2 minimum low byte.
TACH2 minimum high byte.
TACH3 minimum low byte.
TACH3 minimum high byte.
TACH4 minimum low byte.
TACH4 minimum high byte.
Power-On Default
0xFF
0xFF
0xFF
0xFF
0xFF
0xFF
0xFF
0xFF
1
Exceeding any of the TACH limit registers by 1 indicates that the fan is running too slowly or has stalled. The appropriate status bit is set in Interrupt Status Register 2 to
indicate the fan failure. Setting the Configuration Register 1 lock bit has no effect on these registers.
Table 32. Register 0x55—TACH 1 Minimum High Byte (Power-On Default = 0xFF)
Bits
<4:0>
Name
Reserved
R/W
Read-only
<7:5>
SCADC
Read/write
Description
These bits are reserved when Bit 6 of Config 2 Register (0x73) is set (single-channel ADC mode).
Otherwise, these bits represent Bits <4:0> of the TACH1 minimum high byte.
When Bit 6 of Config 2 Register (0x73) is set (single channel ADC mode), these bits are used to select the
only channel from which the ADC makes measurements. Otherwise, these bits represent Bits <7:5> of
the TACH1 minimum high byte.
Rev. 0 | Page 68 of 80
ADT7468
Table 33. PWM Configuration Registers
Register Address
0x5C
0x5D
0x5E
Bit
<2:0>
Name
SPIN
R/W1
Read/write
Read/write
Read/write
R/W
Read/write
<3>
<4>
SLOW
INV
Read/write
Read/write
<7:5>
BHVR
Read/write
1
Description
Power-On Default
PWM1 configuration.
0x82
PWM2 configuration.
0x82
PWM3 configuration.
0x82
Description
These bits control the startup timeout for PWMx. The PWM output stays high until
two valid TACH rising edges are seen from the fan. If there is not a valid TACH signal
during the fan TACH measurement directly after the fan startup timeout period, then
the TACH measurement reads 0xFFFF and Status Register 2 reflects the fan fault. If the
TACH minimum high and low bytes contain 0xFFFF or 0x0000, then the Status
Register 2 bit is not set, even if the fan has not started.
000 = No startup timeout
001 = 100 ms
010 = 250 ms (default)
011 = 400 ms
100 = 667 ms
101 = 1 s
110 = 2 s
111 = 4 s
SLOW = 1 makes the ramp rates for acoustic enhancement four times longer.
This bit inverts the PWM output. The default is 0, which corresponds to a logic high
output for 100% duty cycle. Setting this bit to 1 inverts the PWM output, so 100%
duty cycle corresponds to a logic low output.
These bits assign each fan to a particular temperature sensor for localized cooling.
000 = Remote 1 temperature controls PWMx (automatic fan control mode).
001 = local temperature controls PWMx (automatic fan control mode).
010 = Remote 2 temperature controls PWMx (automatic fan control mode).
011 = PWMx runs full speed.
100 = PWMx disabled (default).
101 = fastest speed calculated by local and Remote 2 temperature controls PWMx.
110 = fastest speed calculated by all three temperature channel controls PWMx.
111 = manual mode. PWM duty cycle registers (Reg. 0x30 to Reg. 0x32) become
writable.
These registers become read-only when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to these registers fail.
Rev. 0 | Page 69 of 80
ADT7468
Table 34. TEMP TRANGE/PWM Frequency Registers
Register Address
0x5F
0x60
0x61
Bit
Name
<2:0>
FREQ
R/W1
Read/write
Read/write
Read/write
R/W
Read/write
<3>
THRM
Read/write
<7:4>
RANGE
Read/write
Description
Power-On Default
Remote 1 TRANGE/PWM1 frequency.
0xC4
Local temperature TRANGE/PWM2 frequency.
0xC4
Remote 2 TRANGE/PWM3 frequency.
0xC4
Description
These bits control the PWMx frequency.
000 = 11.0 Hz
001 = 14.7 Hz
010 = 22.1 Hz
011 = 29.4 Hz
100 = 35.3 Hz (default)
101 = 44.1 Hz
110 = 58.8 Hz
111 = 88.2 Hz
THRM = 1 causes the THERM pin (Pin 14/20) to assert low as an output when this
temperature channel’s THERM limit has been exceeded by 0.25°C. The THERM pin
remains asserted until the temperature is equal to or below the THERM limit. The
minimum time that THERM asserts is one monitoring cycle. This allows clock
modulation of devices that incorporate this feature.
THRM = 0 makes the THERM pin act as an input only, for example, for Pentium 4
PROCHOT monitoring, when Pin 14/20 is configured as THERM.
These bits determine the PWM duty cycle vs. the temperature slope for automatic fan
control.
0000 = 2°C
0001 = 2.5°C
0010 = 3.33°C
0011 = 4°C
0100 = 5°C
0101 = 6.67°C
0110 = 8°C
0111 = 10°C
1000 = 13.33°C
1001 = 16°C
1010 = 20°C
1011 = 26.67°C
1100 = 32°C (Default)
1101 = 40°C
1110 = 53.33°C
1111 = 80°C
1
These registers become read-only when the Configuration Register 1 lock bit is set. Any further attempts to write to these registers have no effect.
Rev. 0 | Page 70 of 80
ADT7468
Table 35. Register 0x62—Enhanced Acoustics Register 1 (Power-On Default = 0x00)
Bit
<2:0>
Name
ACOU
R/W1
Read/write
<3>
<4>
EN1
SYNC
Read/write
Read/write
<5>
MIN1
Read/write
<6>
MIN2
Read/write
<7>
MIN3
Read/write
Description
These bits select the ramp rate applied to the PWM1 output. Instead of PWM1 jumping instantaneously to
its newly calculated speed, PWM1 ramps gracefully at the rate determined by these bits. This feature
enhances the acoustics of the fan being driven by the PWM1 output.
Time Slot Increase
Time for 33% to 100%
000 = 1
35 s
001 = 2
17.6 s
010 = 3
11.8 s
011 = 4
7s
100 = 8
4.4 s
101 = 12
3s
110 = 24
1.6 s
111 = 48
0.8 s
When this bit is 1, acoustic enhancement is enabled on PWM1 output.
SYNC = 1 synchronizes fan speed measurements on TACH2, TACH3, and TACH4 to PWM3. This allows up to
three fans to be driven from PWM3 output and their speeds to be measured.
SYNC = 0 synchronizes only TACH3 and TACH4 to PWM3 output.
When the ADT7468 is in automatic fan control mode, this bit defines whether PWM1 is off (0% duty cycle) or
at PWM1 minimum duty cycle when the controlling temperature is below its TMIN – hysteresis value.
0 = 0% duty cycle below TMIN – hysteresis.
1 = PWM1 minimum duty cycle below TMIN – hysteresis.
When the ADT7468 is in automatic fan speed control mode, this bit defines whether PWM2 is off (0% duty
cycle) or at PWM2 minimum duty cycle when the controlling temperature is below its TMIN – hysteresis value.
0 = 0% duty cycle below TMIN – hysteresis.
1 = PWM 2 minimum duty cycle below TMIN – hysteresis.
When the ADT7468 is in automatic fan speed control mode, this bit defines whether PWM3 is off (0% duty
cycle) or at PWM3 minimum duty cycle when the controlling temperature is below its TMIN – hysteresis value.
0 = 0% duty cycle below TMIN – hysteresis.
1 = PWM3 minimum duty cycle below TMIN – hysteresis.
1
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Rev. 0 | Page 71 of 80
ADT7468
Table 36. Register 0x63 – Enhanced Acoustics Register 2 (Power-On Default = 0x00)
Bit
<2:0>
Name
ACOU3
R/W1
Read/write
<3>
<6:4>
EN3
ACOU2
Read/write
Read/write
<7>
EN2
Read/write
1
Description
These bits select the ramp rate applied to the PWM3 output. Instead of PWM3 jumping instantaneously to
its newly calculated speed, PWM3 ramps gracefully at the rate determined by these bits. This effect
enhances the acoustics of the fan being driven by the PWM3 output.
Time Slot Increase
Time for 33% to 100%
000 = 1
35 s
001 = 2
17.6 s
010 = 3
11.8 s
011 = 5
7s
100 = 8
4.4 s
101 = 12
3s
110 = 24
1.6 s
111 = 48
0.8 s
When this bit is 1, acoustic enhancement is enabled on PWM3 output.
These bits select the ramp rate applied to the PWM2 output. Instead of PWM2 jumping instantaneously to
its newly calculated speed, PWM2 ramps gracefully at the rate determined by these bits. This effect
enhances the acoustics of the fans being driven by the PWM2 output.
Time Slot Increase
Time for 33% to 100%
000 = 1
35 s
001 = 2
17.6 s
010 = 3
11.8 s
011 = 5
7s
100 = 8
4.4 s
101 = 12
3s
110 = 24
1.6 s
When this bit is 1, acoustic enhancement is enabled on PWM2 output.
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Table 37. PWM Minimum Duty Cycle Registers
Register Address
0x64
0x65
0x66
Bit
Name
<7:0>
PWM duty cycle
R/W1
Read/write
Read/write
Read/write
R/W1
Read/write
Description
PWM1 minimum duty cycle.
PWM2 minimum duty cycle.
PWM3 minimum duty cycle.
Description
These bits define the PWMMIN duty cycle for PWMx.
0x00 = 0% duty cycle (fan off ).
0x40 = 25% duty cycle.
0x80 = 50% duty cycle.
0xFF = 100% duty cycle (fan full speed).
Power-On Default
0x80 (50% duty cycle)
0x80 (50% duty cycle)
0x80 (50% duty cycle)
1
These registers become read-only when the ADT7468 is in automatic fan control mode.
Table 38. TMIN Registers1
Register Address
0x67
0x68
0x69
R/W2
Read/write
Read/write
Read/write
Description
Remote 1 temperature TMIN.
Local temperatue TMIN.
Remote 2 temperature TMIN.
Power-On Default
0x5A (90°C)
0x5A (90°C)
0x5A (90°C)
1
These are the TMIN registers for each temperature channel. When the temperature measured exceeds TMIN, the appropriate fan runs at minimum speed and increases
with temperature according to TRANGE.
2
These registers become read-only when the Configuration Register 1 lock bit is set. Any further attempts to write to these registers have no effect.
Rev. 0 | Page 72 of 80
ADT7468
Table 39. THERM Limit Registers1
Register Address
0x6A
0x6B
0x6C
R/W2
Read/write
Read/write
Read/write
Description
Remote 1 THERM limit.
Local THERM limit.
Remote 2 THERM limit.
Power-On Default
0x64 (100°C)
0x64 (100°C)
0x64 (100°C)
If any temperature measured exceeds its THERM limit, all PWM outputs drive their fans at 100% duty cycle. This is a fail-safe mechanism incorporated to cool the
system in the event of a critical overtemperature. It also ensures some level of cooling in the event that software or hardware locks up. If set to 0x80, this feature is
disabled. The PWM output remains at 100% until the temperature drops below THERM limit – hysteresis. If the THERM pin is programmed as an output, then exceeding
these limits by 0.25°C can cause the THERM pin to assert low as an output.
2
These registers become read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to these registers have no effect.
1
Table 40. Temperature/TMIN Hysteresis Registers1
Register Address
0x6D
<3:0>
R/W2
Read/write
HYSL
<7:4>
HYSR1
0x6E
<7:4>
Read/write
HYSR2
Description
Remote 1 and local temperature hysteresis.
Local temperature hyseresis. 0°C to 15°C of
hysteresis can be applied to the local temperature
AFC and dynamic TMIN control loops.
Remote 1 temperature hyseresis. 0°C to 15°C of
hysteresis can be applied to the Remote 1
temperature AFC and dynamic TMIN control loops.
Remote 2 temperature hysteresis.
Local temperature hyseresis. 0°C to 15°C of
hysteresis can be applied to the local temperature
AFC and dynamic TMIN control loops.
Power-On Default
0x44
0x40
1
Each 4-bit value controls the amount of temperature hysteresis applied to a particular temperature channel. Once the temperature for that channel falls below its TMIN
value, the fan remains running at PWMMIN duty cycle until the temperature = TMIN – hysteresis. Up to 15°C of hysteresis can be assigned to any temperature channel. The
hysteresis value chosen also applies to that temperature channel, if its THERM limit is exceeded. The PWM output being controlled goes to 100%, if the THERM limit is
exceeded and remains at 100% until the temperature drops below THERM – hysteresis. For acoustic reasons, it is recommended that the hysteresis value not be
programmed less than 4°C. Setting the hysteresis value lower than 4°C causes the fan to switch on and off regularly when the temperature is close to TMIN.
2
These registers become read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to these registers have no effect.
Table 41. XNOR Tree Test Enable
Register Address
0x6F
<0>
R/W1
Read/write
XEN
<7:1>
Reserved
1
Description
XNOR tree test enable register.
If the XEN bit is set to 1, the device enters the XNOR
tree test mode. Clearing the bit removes the device
from the XNOR tree test mode.
Unused. Do not write to these bits.
Power-On Default
0x00
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Table 42. Remote 1 Temperature Offset
Register Address
0x70
<7:0>
1
R/W1
Read/write
Read/write
Description
Remote 1 temperature offset.
Allows a twos complement offset value to be
automatically added to or subtracted from the
Remote 1 temperature reading. This is to
compensate for any inherent system offsets such as
PCB trace resistance. LSB value = 0.5°C.
Power-On Default
0x00
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Rev. 0 | Page 73 of 80
ADT7468
Table 43. Local Temperature Offset
Register Address
0x71
<7:0>
1
R/W1
Read/write
Read/write
Description
Local temperature offset.
Allows a twos complement offset value to be
automatically added to or subtracted from the local
temperature reading. LSB value = 0.5°C.
Power-On Default
0x00
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Table 44. Remote 2 Temperature Offset
Register Address
0x72
<7:0>
1
R/W1
Read/write
Read/write
Description
Remote 2 temperature offset.
Allows a twos complement offset value to be
automatically added to or subtracted from the
Remote 2 temperature reading. This is to
compensate for any inherent system offsets such as
PCB trace resistance. LSB value = 0.5°C.
Power-On Default
0x00
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Table 45. Register 0x73—Configuration Register 2 (Power-On Default = 0x00)
Bit
0
Name
AIN1
R/W1
Read/write
1
AIN2
Read/write
2
AIN3
Read/write
3
AIN4
Read/write
4
AVG
Read/write
5
ATTN
Read/write
6
CONV
Read/write
7
SHDN
Read/write
1
Description
AIN1 = 0, speed of 3-wire fans measured using the TACH output from the fan.
AIN1 = 1, Pin 6 is reconfigured to measure the speed of 2-wire fans using an
external sensing resistor and coupling capacitor. AIN voltage threshold is set via
Configuration Register 4 (Reg. 0x7D). Only relevant in low frequency mode.
AIN2 = 0, speed of 3-wire fans measured using the TACH output from the fan.
AIN2 = 1, Pin 7 is reconfigured to measure the speed of 2-wire fans using an
external sensing resistor and coupling capacitor. AIN voltage threshold is set via
Configuration Register 4 (Reg. 0x7D). Only relevant in low frequency mode.
AIN3 = 0, speed of 3-wire fans measured using the TACH output from the fan.
AIN3 = 1, Pin 4 is reconfigured to measure the speed of 2-wire fans using an
external sensing resistor and coupling capacitor. AIN voltage threshold is set via
Configuration Register 4 (Reg. 0x7D). Only relevant in low frequency mode.
AIN4 = 0, speed of 3-wire fans measured using the TACH output from the fan.
AIN4 = 1, Pin 9 is reconfigured to measure the speed of 2-wire fans using an
external sensing resistor and coupling capacitor. AIN voltage threshold is set via
Configuration Register 4 (Reg. 0x7D). Only relevant in low frequency mode.
AVG = 1, averaging on the temperature and voltage measurements is turned off.
This allows measurements on each channel to be made much faster.
ATTN = 1, the ADT7468 removes the attenuators from the 2.5 V, VCCP, 5 V, and 12 V
inputs. These inputs can be used for other functions such as connecting up
external sensors. It is possible to remove attenuators from individual channels
using Bits <7:4> of Configuration Register 4 (0x7D).
CONV = 1, the ADT7468 is put into a single-channel ADC conversion mode. In this
mode, the ADT7468 can be made to read continuously from one input only, for
example, Remote 1 temperature. The appropriate ADC channel is selected by
writing to Bits <7:5> of TACH1 minimum high byte register (0x55).
Bits <7:5> Reg. 0x55
000
2.5 V
001
VCCP
010
VCC (3.3 V)
011
5V
100
12 V
101
Remote 1 temperature
110
Local temperature
111
Remote 2 temperature
SHDN = 1, ADT7468 goes into shutdown mode. All PWM outputs assert low (or
high depending on state of INV bit) to switch off all fans. The PWM current duty
cycle registers read 0x00 to indicate that the fans are not being driven.
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Rev. 0 | Page 74 of 80
ADT7468
Table 46. Register 0x74—Interrupt Mask Register 1 (Power-On Default <7:0> = 0x00)
Bit
0
1
2
3
4
5
6
7
Name
2.5V
VCCP
VCC
5V
RIT
LT
R2T
OOL
R/W
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Description
2.5 V = 1, masks SMBALERT for out-of-limit conditions on the 2.5 V channel.
VCCP = 1, masks SMBALERT for out-of-limit conditions on the VCCP channel.
VCC = 1, masks SMBALERT for out-of-limit conditions on the VCC channel.
5 V = 1, masks SMBALERT for out-of-limit conditions on the 5 V channel.
RIT = 1, masks SMBALERT for out-of-limit conditions on the Remote 1 temperature channel.
LT = 1, masks SMBALERT for out-of-limit conditions on the local temperature channel.
R2T = 1, masks SMBALERT for out-of-limit conditions on the Remote 2 temperature channel.
OOL = 1, masks SMBALERT for any out-of-limit condition in Status Register 2.
Table 47. Register 0x75—Interrupt Mask Register 2 (Power-On Default <7:0> = 0x00)
Bit
Name
R/W
0
12V/VC
Read/write
1
OVT
Read only
2
3
4
5
FAN1
FAN2
FAN3
F4P
Read/write
Read/write
Read/write
Read/write
6
7
D1
D2
Read/write
Read/write
Description
When Pin 21 is configured as a 12 V input, 12V/VC = 1 masks SMBALERT for out-of-limit conditions
on the 12 V channel. When Pin 21 is programmed as VID5, this bit masks an SMBALERT, if the VID5
VID code bit changes.
OVT = 1, masks SMBALERT for overtemperature THERM conditions.
FAN1 = 1, masks SMBALERT for a Fan 1 fault.
FAN2 = 1, masks SMBALERT for a Fan 2 fault.
FAN3 = 1, masks SMBALERT for a Fan 3 fault.
If Pin 14 is configured as TACH 4, F4P = 1 masks SMBALERT for a Fan 4 fault.
If Pin 14 is configured as THERM, F4P = 1 masks SMBALERT for an exceeded THERM timer limit.
If Pin 14 is configured as GPIO, F4P = 1 masks SMBALERT when GPIO is an input and GPIO is
asserted.
D1 = 1 masks SMBALERT for a diode open or short on a Remote 1 channel.
D2 = 1 masks SMBALERT for a diode open or short on a Remote 2 channel.
Table 48. Register 0x76—Extended Resolution Register 11
Bit
<1:0>
<3:2>
<5:4>
<7:6>
1
Name
2.5V
VCCP
VCC
5V
R/W
Read-only
Read-only
Read-only
Read-only
Description
2.5 V LSBs. Holds the 2 LSBs of the 10-bit 2.5 V measurement.
VCCP LSBs. Holds the 2 LSBs of the 10-bit VCCP measurement.
VCC LSBs. Holds the 2 LSBs of the 10-bit VCC measurement.
5 V LSBs. Holds the 2 LSBs of the 10-bit 5 V measurement.
If this register is read, this register and the registers holding the MSB of each reading are frozen until read.
Table 49. Register 0x77—Extended Resolution Register 21
Bit
<1:0>
<3:2>
<5:4>
<7:6>
1
Name
12V
TDM1
LTMP
TDM2
R/W
Read-only
Read-only
Read-only
Read-only
Description
12 V LSBs. Holds the 2 LSBs of the 10-bit 12 V measurement.
Remote 1 temperature LSBs. Holds the 2 LSBs of the 10-bit Remote 1 temperature measurement.
Local temperature LSBs. Holds the 2 LSBs of the 10-bit local temperature measurement.
Remote 2 temperature LSBs. Holds the 2 LSBs of the 10-bit Remote 2 temperature measurement.
If this register is read, this register and the registers holding the MSB of each reading are frozen until read.
Rev. 0 | Page 75 of 80
ADT7468
Table 50. Register 0x78—Configuration Register 3 (Power-On Default = 0x00)
Bit
<0>
Name
ALERT
R/W1
Read/write
<1>
THERM
Read/write
<2>
BOOST
Read/write
<3>
FAST
Read/write
<4>
DC1
Read/write
<5>
DC2
Read/write
<6>
DC3
Read/write
<7>
DC4
Read/write
1
Description
ALERT = 1, Pin 10 (PWM2/SMBALERT) is configured as an SMBALERT interrupt output to indicate
out-of-limit error conditions.
ALERT = 0, Pin 10 (PWM2/SMBALERT) is configured as the PWM2 output.
THERM Enable = 1 enables THERM functionality on Pin 20 and Pin 14, if Pin 14 is configured as
THERM, determined by Bits 0 and 1 (PIN14FUNC) of Configuration Register 4. When THERM is
asserted, if the fans are running and the boost bit is set, the fans run at full speed. Alternatively,
THERM can be programmed so that a timer is triggered to time how long THERM has been asserted.
When THERM is an input and BOOST = 1, assertion of THERM causes all fans to run at the maximum
programmed duty cycle for fail-safe cooling.
FAST = 1, enables fast TACH measurements on all channels. This increases the TACH measurement
rate from once per second to once every 250 ms (4 ×).
DC1 = 1, enables TACH measurements to be continuously made on TACH1. Fans must be driven by
dc. Setting this bit prevents pulse stretching, because it is not required for dc-driven motors.
DC2 = 1, enables TACH measurements to be continuously made on TACH2. Fans must be driven by
dc. Setting this bit prevents pulse stretching, because it is not required for dc-driven motors.
DC3 = 1, enables TACH measurements to be continuously made on TACH3. Setting this bit prevents
pulse stretching, because it is not required for dc-driven motors.
DC4 = 1, enables TACH measurements to be continuously made on TACH4. Setting this bit prevents
pulse stretching, because it is not required for dc-driven motors.
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Table 51. Register 0x79—THERM Timer Status Register (Power-On Default = 0x00)
Bit
<7:1>
Name
TMR
R/W
Read-only
<0>
ASRT/
TMR0
Read-only
Description
Times how long THERM input is asserted. These seven bits read zero until the THERM assertion time
exceeds 45.52 ms.
This bit is set high on the assertion of the THERM input and is cleared on read. If the THERM
assertion time exceeds 45.52 ms, this bit is set and becomes the LSB of the 8-bit TMR reading. This
allows THERM assertion times from 45.52 ms to 5.82 s to be reported back with a resolution of
22.76 ms.
Table 52. Register 0x7A—THERM Timer Limit Register (Power-On Default = 0x00)
Bit
<7:0>
Name
LIMT
R/W
Read/write
Description
Sets maximum THERM assertion length allowed before an interrupt is generated. This is an 8-bit
limit with a resolution of 22.76 ms allowing THERM assertion limits of 45.52 ms to 5.82 s to be
programmed. If the THERM assertion time exceeds this limit, Bit 5 (F4P) of Interrupt Status Register
2 (Reg. 0x42) is set. If the limit value is 0x00, then an interrupt is generated immediately on the
assertion of the THERM input.
Rev. 0 | Page 76 of 80
ADT7468
Table 53. Register 0x7B—TACH Pulses per Revolution Register (Power-On Default = 0x55)
Bit
<1:0>
Name
FAN1
R/W
Read/write
<3:2>
FAN2
Read/write
<5:4>
FAN3
Read/write
<7:6>
FAN4
Read/write
Description
Sets number of pulses to be counted when measuring Fan 1 speed. Can be used to determine fan
pulses per revolution for unknown fan type.
Pulses Counted
00 = 1
01 = 2 (default)
10 = 3
11 = 4
Sets number of pulses to be counted when measuring Fan 2 speed. Can be used to determine fan
pulses per revolution for unknown fan type.
Pulses Counted
00 = 1
01 = 2 (default)
10 = 3
11 = 4
Sets number of pulses to be counted when measuring Fan 3 speed. Can be used to determine fan
pulses per revolution for unknown fan type.
Pulses Counted
00 = 1
01 = 2 (default)
10 = 3
11 = 4
Sets number of pulses to be counted when measuring Fan 4 speed. Can be used to determine fan
pulses per revolution for unknown fan type.
Pulses Counted
00 = 1
01 = 2 (default)
10 = 3
11 = 4
Table 54. Register 0x7C—Configuration Register 5 (Power-On Default = 0x00)
Bit
<0>
Name
2sC
<1>
<2>
HF/LF
GPIOD
<3>
GPIOP
<4:7>
RES
R/W1
Read/write
Description
2sC = 1, sets the temperature range to twos complement temperature range.
2sC = 0, changes the temperature range to Offset 64. When this bit is changed, the ADT7468 interprets
all relevant temperature register values as defined by this bit.
Sets the PWM drive frequency to high frequency mode (0) or low frequency mode (1).
GPIO direction. When GPIO function is enabled, this determines whether the GPIO is an input (0) or an
output (1).
GPIO polarity. When the GPIO function is enabled and is programmed as an output, this bit
determines whether the GPIO is active low (0) or high (1).
Unused.
1
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Rev. 0 | Page 77 of 80
ADT7468
Table 55. Register 0x7D—Configuration Register 4 (Power-On Default = 0x00)
Bit
<1:0>
Name
PIN14FUNC
R/W1
Read/write
<3:2>
AINL
Read/write
<4>
BpAtt2.5V
<5>
BpAttVCCP
<6>
BpAtt5V
<7>
BpAtt12V
1
Description
These bits set the functionality of Pin 14:
00 = TACH4 (default)
01 = Bidirectional THERM
10 = SMBALERT
11 = GPIO
These two bits define the input threshold for 2-wire fan speed measurements (low frequency mode
only):
00 = ±20 mV
01 = ±40 mV
10 = ±80 mV
11 = ±130 mV
Bypass 2.5 V attenuator. When set, the measurement scale for this channel changes from 0 V (0x00) to
2.2965 V (0xFF).
Bypass VCCP attenuator. When set, the measurement scale for this channel changes from 0 V (0x00) to
2.2965 V (0xFF).
Bypass 5 V attenuator. When set, the measurement scale for this channel changes from 0 V (0x00) to
2.2965 V (0xFF).
Bypass 12 V attenuator. When set, the measurement scale for this channel changes from 0 V (0x00) to
2.2965 V (0xFF).
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Any further attempts to write to this register have no effect.
Table 56. Register 0x7E—Manufacturer’s Test Register 1 (Power-On Default = 0x00)
Bit
<7:0>
Name
Reserved
R/W
Read-only
Description
Manufacturer’s test register. These bits are reserved for manufacturer’s test purposes and should not
be written to under normal operation.
Table 57. Register 0x7F—Manufacturer’s Test Register 2 (Power-On Default = 0x00)
Bit
<7:0>
Name
Reserved
R/W
Read-only
Description
Manufacturer’s test register. These bits are reserved for manufacturer’s test purposes and should not
be written to under normal operation.
Rev. 0 | Page 78 of 80
Figure 85.
Rev. 0 | Page 79 of 80
ALLOW SELECTED
PWM TO TURN OFF
WHEN TEMP IS BELOW
TMIN–HYST
SYNC FAN SPEED
MEASUREMENTS
ENABLE
SELECTED PWM
RAMP-UP SPEED
SELECTED PWM
RAMP-UP SPEED
TEMPERATURE HYSTERESIS
(THYST)
(0x6D, 0x6E)
04498-0-044
16°C
88.2Hz
80°C
53.33°C
40°C
32°C
26.67°C
20°C
10°C
13.33°C
35.3Hz
58.8Hz
8°C
29.4Hz
44.1Hz
5°C
6.67°C
22.1Hz
4°C
14.7Hz
THERM AS
OVERTEMP
OUTPUT
THERM AS
(TIMER) INPUT
667ms
1s
2s
4s
1 PULSE PER REV
2 PULSE PER REV
3 PULSE PER REV
4 PULSE PER REV
XNOR Test
(0x6F)
THERM TEMP
LIMITS
(0x6A, 0x6B, 0x6C)
AVERAGE TEMP
AND VOLTAGE
MEASUREMENTS
(SEE CONFIGURATION 2,
0x73)
VCCP HIGH LIMIT
(0x47)
VCCP LOW LIMIT
(0x46)
VCCP LOW
(SLEEP)
CYXX
TMIN ADJUSTMENT
CYCLE TIME
ENABLE DYNAMIC TMIN
CONTROL ON INDIVIDUAL
CHANNEL
FASTEST SPEED CALCULATED BY ALL
3 TEMPERATURE CHANNEL CONTROLS
THERM
GENERAL
INTERRUPT
FANS
VOLTAGES
TEMPERATURE
2048 CYCLES (256s)
1024 CYCLES (128s)
512 CYCLES (64s)
256 CYCLES (32s)
128 CYCLES (16s)
64 CYCLES (8s)
32 CYCLES (4s)
16 CYCLES (2s)
DECREASE
CYCLE TIME
1024 CYCLES (128s)
512 CYCLES (64s)
256 CYCLES (32s)
128 CYCLES (16s)
64 CYCLES (8s)
32 CYCLES (4s)
16 CYCLES (2s)
8 CYCLES (1s)
BYPASS VCCP
ATTENUATOR
TMIN
THYST
COOLING
TRANGE = SLOPE
THYST
MIN PWM
0% DUTY CYCLE
TWOS COMPLEMENT
OFFSET 64
F4P
DRIVE PWM
OUTPUTS
HIGH/LOW
T THERM
HEATING
AUTOMATIC FAN CONTROL
TEMPERATURE
GPIO POLARITY
GPIO DIRECTION
FAN DRIVE
HIGH/LOW
FREQUENCY
MODE
100% DUTY CYCLE
MAX PWM
±130mV
±80mV
±20mV
±40mV
INPUT THRESHOLD
FOR 2-WIRE FANS
(AINL)
GPIO
SMBALERT
THERM
TACH 4
SMBALERT
MASK INTERRUPT?
(0x74,0x75)
TEMPERATURE
RANGE
CONFIGURATION 5
(0X7C)
(ONLY USED WHEN FANS ARE
POWERED BY DC AND NOT PWM)
SMBALERT
PWM 2
SET PIN 14/20
FUNCTIONALITY
THERM
INTERRUPTS
ON STATUS
REGISTER 2
SHUTDOWN
SINGLE CHANNEL
ADC MODE
RESCALE VCCP
INPUT (5V/3.3V)
AVERAGE TEMP
AND VOLTAGE
MEASUREMENTS
MEASURE
FROM 2- OR 3WIRE FANS
INTERRUPT STATUS
(0x41, 0x42)
HARDWARE INTERRUPTS
FAN FAULT
DIODE FAULT.
FOR REMOTE
CHANNELS ONLY
TEMPERATURE
MEASURED IS
OUT OF LIMITS
THERM TIMER
LIMIT HAS BEEN
EXCEEDED
ENABLE CONTINUOUS
FAN SPEED
MEASUREMENT
CONFIGURE
PIN 10
FAST TACH
MEASUREMENTS
CONFIGURATION 4
(0x7D)
RESCALE VCC
(5V/3.3V)
RUN FANS AT
FULLSPEED
READY
LOCK
SETTINGS
TEMPERATURE
MEASUREMENT
HIGH LIMIT
LOW LIMIT
(0X4E-0X53)
TEMPERATURE
OFFSET
(0x70-0x72)
SOFTWARE INTERRUPTS
TEMPERATURE
MEASUREMENT
(0X25, 0X26,0X27)
START
MONITORING
CONFIGURATION 1
(0X40)
THERM BOOST (FAN MUST BE RUNNING)
ENABLE THERM
MANUAL MODE. PWM DUTY CYCLE
REGISTERS (0x30-0x32) BECOME WRITABLE
CHANGE
CYCLE TIME
INCREASE
CYCLE TIME
MEASUREMENT LSBs
(0X77)
IF THESE REGISTERS ARE USED,
ALL TEMPERATURE MEASUREMENT
MSB REGISTERS ARE FROZEN
UNTIL ALL TEMPERATURE
MEASUREMENT MSB REGISTERS
ARE READ.
FASTEST SPEED CALCULATED
BY LOCAL AND REMOTE 2 TEMP
CONTROLS SELECTED PWM DRIVE
SELECTED PWM DRIVE
DISABLED (DEFAULT)
SELECTED PWM DRIVE
RUNS FULL SPEED
REMOTE 2 TEMP CONTROLS
SELECTED PWM DRIVE (AFC MODE)
LOCAL TEMP CONTROLS SELECTED
PWM DRIVE (AFC MODE)
VCC HIGH LIMIT
(0x49)
VCC LOW LIMIT
(0x48)
MEASUREMENT MSBs
(0x25-0x27)
VCC MEASUREMENT
(0x22)
REMOTE 1 TEMP CONTROLS
SELECTED PWM DRIVE (AFC MODE)
CONFIGURATION 3
(0x78)
PHTXX
CURRENT TEMPERATURE OF SELECTED
CHANNEL IS COPIED TO RELEVANT OPERATING
POINT REGISTER ON ASSERTION OF THERM
VCCP MEASUREMENT
(0x47)
THERM TIMER
STATUS (0x79)
THERM TIMER
LIMIT (0x7A)
DYNAMIC TMIN
CONTROL
(0x36, 0x37)
PWMMIN DUTY CYCLE
(AUTOMATIC MODE ONLY)
(0X64-0X66)
PWM DUTY CYCLE
(MANUAL MODE ONLY)
(0x30-0x32)
MAX FAN SPEED
(MAX PWM DUTY CYCLE)
(0x38-0x3A)
ADT7467/ADT7468 PROGRAMMING BLOCK DIAGRAM
PWM
FREQUENCY
2.5°C
3.33°C
11.0Hz
2°C
THERM IS
INPUT/OUTPUT
AUTOMATIC FAN
CONTROL
0.8s (33%-100%)
1.6s (33%-100%)
3s (33%-100%)
400ms
100ms
NO TIMEOUT
4.4s (33%-100%)
FAN SPINUP
TIMEOUT
FAN BEHAVIOR
SLOW IMPROVED
ACOUSTIC RAMP-UP
INVERT PWM
OUTPUT
250ms (DEFAULT)
FAN TACH
PULSES PER REV
(0x7B)
PWM CONFIGURATION
(0x5C-0x5E)
FANTACH 16-BIT
MINIMUM LIMIT
(0X54-0X5B)
7s (33%-100%)
18s (33%-100%)
17.6s (33%-100%)
35s (33%-100%)
TRANGE
TEMP TRANGE,PWM
FREQ,THERMENABLE
(0x5F, 0x60, 0x61)
OPERATING
POINT
(0x33-0x35)
FAN 16-BIT MEASUREMENT
(0x28-0x2F)
LOW BYTE MUST BE READ FIRST.
WHEN THE LOW BYTE IS READ,
REGISTERS ARE LOCKED UNTIL THE
ASSOCIATED HIGH BYTE IS READ.
TMIN. MIN TEMP THAT CAUSES
SELECTED FANS TO RUN
(0x67-0x69)
ENHANCE
ACOUSTICS
(0x62,0x63)
LOCAL TEMP
REMOTE TEMP2
REMOTE TEMP1
VCC
PWM DUTY CYCLE/RELATIVE FAN SPEED
VCCP
CONFIGURATION 2
(0X73)
ADT7468
ADT7468 PROGRAMMING BLOCK DIAGRAM
ADT7468
OUTLINE DIMENSIONS
0.341
BSC
24
13
0.154
BSC
1
0.236
BSC
12
PIN 1
0.069
0.053
0.065
0.049
0.010
0.004
0.025
BSC
COPLANARITY
0.004
0.012
0.008
SEATING
PLANE
0.010
0.006
8°
0°
0.050
0.016
COMPLIANT TO JEDEC STANDARDS MO-137AE
Figure 86. 24-Lead Shrink Small Outline Package [QSOP]
(RQ-24)
Dimensions shown in inches
ORDERING GUIDE
Model
ADT7468ARQ
ADT7468ARQ-REEL
ADT7468ARQ-REEL7
Temperature Range
–40°C to +120°C
–40°C to +120°C
–40°C to +120°C
Package Description
24-Lead QSOP
24-Lead QSOP
24-Lead QSOP
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04499–0–4/04(0)
Rev. 0 | Page 80 of 80
Package Option
RQ-24
RQ-24
RQ-24
Similar pages