AD ADV7195KS Multiformat progressive scan/hdtv encoder with three 11-bit dacs and 10-bit data input Datasheet

a
Multiformat Progressive Scan/HDTV
Encoder with Three 11-Bit DACs
and 10-Bit Data Input
ADV7195
FEATURES
INPUT FORMATS
YCrCb in 2 10-Bit (4:2:2) or 3 10-Bit (4:4:4) FormatCompliant to SMPTE-293M (525p), ITU-R.BT1358
(625p), SMPTE274M (1080i), SMPTE296M (720p)
and Any Other High-Definition Standard Using
Async Timing Mode
RGB in 3 10 Bit (4:4:4) Format
OUTPUT FORMATS
YPrPb Progressive Scan (EIA-770.1, EIA-770.2)
YPrPb HDTV (EIA-770.3)
RGB Levels Compliant to RS-170 and RS-343A
11-Bit + Sync (DAC A)
11-Bit DACs (DAC B, DAC C)
PROGRAMMABLE FEATURES
Internal Test Pattern Generator with Color Control
Y/C Delay ()
Gamma Correction
Individual DAC On/Off Control
54 MHz Output (2 Oversampling)
Sharpness Filter with Programmable Gain/Attenuation
Programmable Adaptive Filter Control
Undershoot Limiter
VBI Open Control
I2C® Filter
CGMS-A (525p)
2-Wire Serial MPU Interface
Single Supply 3.3 V Operation
52-MQFP Package
APPLICATIONS
Progressive Scan/HDTV Display Devices
MPEG at 81 MHz
Progressive Scan/HDTV Projection Systems
Digital Video Systems
High Resolution Color Graphics
Image Processing/Instrumentation
Digital Radio Modulation/Video Signal Reconstruction
GENERAL DESCRIPTION
The ADV7195 is a triple high-speed, digital-to-analog encoder
on a single monolithic chip. It consists of three high-speed video
D/A converters with TTL-compatible inputs.
FUNCTIONAL BLOCK DIAGRAM
SHARPNESS
FILTER CONTROL
AND
ADAPTIVE
FILTER CONTROL
ADV7195
CGMS
MACROVISION
Y0–Y9
Cr0–Cr9
Cb0–Cb9
CLKIN
HORIZONTAL
SYNC
VERTICAL
SYNC
BLANKING
RESET
TEST PATTERN
GENERATOR
AND
DELAY
AND
GAMMA
CORRECTION
CHROMA
4:2:2
TO
4:4:4
(SSAF)
LUMA
SSAF
2 INTERPOLATION
CHROMA
4:2:2
TO
4:4:4
(SSAF)
11-BIT+
SYNC
DAC
DAC A (Y)
11-BIT
DAC
DAC B
11-BIT
DAC
DAC C
SYNC
GENERATOR
TIMING
GENERATOR
I2C MPU
PORT
DAC CONTROL
BLOCK
VREF
RESET
COMP
The ADV7195 has three separate 10-bit-wide input ports that
accept data in 4:4:4 10-bit YCrCb or RGB or 4:2:2 10-bit YCrCb.
This data is accepted in progressive scan format at 27 MHz or
HDTV format at 74.25 MHz or 74.1758 MHz. For any other
high-definition standard but SMPTE293M, ITU-R BT.1358,
SMPTE274M or SMPTE296M the Async Timing Mode can
be used to input data to the ADV7195. For all standards, external horizontal, vertical, and blanking signals or EAV/SAV codes
control the insertion of appropriate synchronization signals into
the digital data stream and therefore the output signals.
The ADV7195 outputs analog YPrPb progressive scan format
complying to EIA-770.1, EIA-770.2; YPrPb HDTV complying
to EIA-770.3; RGB complying to RS-170/RS-343A.
The ADV7195 requires a single 3.3 V power supply, an
optional external 1.235 V reference and a 27 MHz clock in
Progressive Scan Mode or a 74.25 MHz (or 74.1758 MHz)
clock in HDTV mode.
In Progressive Scan Mode, a sharpness filter with programmable
gain allows high-frequency enhancement on the luminance signal.
Programmable Adaptive Filter Control, which may be used,
allows removal of ringing on the incoming Y data. The ADV7195
supports CGMS-A data control generation.
The ADV7195 is packaged in a 52-lead MQFP package.
I2C is a registered trademark of Philips Corporation.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
ADV7195
TABLE OF CONTENTS
MODE REGISTER 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR3 (MR37–MR30) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR3 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 18
HDTV Enable (MR30) . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reserved (MR31–MR32) . . . . . . . . . . . . . . . . . . . . . . . . . 18
DAC A Control (MR33) . . . . . . . . . . . . . . . . . . . . . . . . . 18
DAC B Control (MR34) . . . . . . . . . . . . . . . . . . . . . . . . . 18
DAC C Control (MR35) . . . . . . . . . . . . . . . . . . . . . . . . . 18
Interpolation (MR36) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reserved (MR37) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MODE REGISTER 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR4 (MR47–MR40) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR4 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 18
Timing Reset (MR40) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MODE REGISTER 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR5 (MR57–MR50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MR5 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reserved (MR50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RGB Mode (MR51) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sync on PrPb (MR52) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Color Output Swap (MR53) . . . . . . . . . . . . . . . . . . . . . . 19
Gamma Curve (MR54) . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Gamma Correction (MR55) . . . . . . . . . . . . . . . . . . . . . . 19
Adaptive Mode Control (MR56) . . . . . . . . . . . . . . . . . . . 19
Adaptive Filter Control (MR57) . . . . . . . . . . . . . . . . . . . 19
COLOR Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CY (CY7–CY0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
COLOR CR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CCR (CCR7–CCR0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
COLOR CB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CCB (CCB7–CCB0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MODE REGISTER 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MR6 (MR67–MR60) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MR6 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 20
MR67–MR60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
CGMS DATA REGISTERS 2–0 . . . . . . . . . . . . . . . . . . . . 20
CGMS2 (CGMS27–CGMS20) . . . . . . . . . . . . . . . . . . . . 20
CGMS1 (CGMS17–CGMS10) . . . . . . . . . . . . . . . . . . . . 20
CGMS0 (CGMS07–CGMS00) . . . . . . . . . . . . . . . . . . . . 20
FILTER GAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FG (FG7–FG0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FG BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Filter Gain A (FG3–FG0) . . . . . . . . . . . . . . . . . . . . . . . . 21
Filter Gain B (FG4–FG7) . . . . . . . . . . . . . . . . . . . . . . . . 21
GAMMA CORRECTION REGISTERS 0–13
(GAMMA CORRECTION 0–13) . . . . . . . . . . . . . . . . . . 21
SHARPNESS FILTER CONTROL AND
ADAPTIVE FILTER CONTROL . . . . . . . . . . . . . . . . . 22
SHARPNESS FILTER MODE . . . . . . . . . . . . . . . . . . . . . 22
ADAPTIVE FILTER MODE . . . . . . . . . . . . . . . . . . . . . . . 22
ADAPTIVE FILTER GAIN 1 . . . . . . . . . . . . . . . . . . . . . . 23
AFG1 (AFG1)7–0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ADAPTIVE FILTER GAIN 2 . . . . . . . . . . . . . . . . . . . . . . 23
AFG2 (AFG2)7–0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ADAPTIVE FILTER GAIN 3 . . . . . . . . . . . . . . . . . . . . . . 23
AFG3 (AFG3)7–0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . 1
3.3 V SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 V DYNAMIC–SPECIFICATIONS . . . . . . . . . . . . . . . . . . 4
3.3 V TIMING–SPECIFICATIONS . . . . . . . . . . . . . . . . . . 5
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 8
ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . 9
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . 10
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Analog Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Undershoot Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
I2C Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Internal Test Pattern Generator . . . . . . . . . . . . . . . . . . . . 10
Y/CrCb Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Gamma Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
54 MHz Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PROGRAMMABLE SHARPNESS FILTER . . . . . . . . . . . 10
PROGRAMMABLE ADAPTIVE FILTER CONTROL . . 11
INPUT/OUTPUT CONFIGURATION . . . . . . . . . . . . . . 11
MPU PORT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 11
REGISTER ACCESSES . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
REGISTER PROGRAMMING . . . . . . . . . . . . . . . . . . . . . 13
Subaddress Register (SR7–SR0) . . . . . . . . . . . . . . . . . . . 13
Register Select (SR6–SR0) . . . . . . . . . . . . . . . . . . . . . . . . 13
PROGRESSIVE SCAN MODE . . . . . . . . . . . . . . . . . . 14
MODE REGISTER 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MR0 (MR07–MR00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MR0 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 14
Output Standard Selection (MR00–MR01) . . . . . . . . . . . 14
Input Control Signals (MR02–MR03) . . . . . . . . . . . . . . . 14
Input Standard (MR04) . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reserved (MR05) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DV Polarity (MR06) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reserved (MR07) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MODE REGISTER 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MR1 (MR17–MR10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MR1 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 16
Pixel Data Enable (MR10) . . . . . . . . . . . . . . . . . . . . . . . . 16
Input Format (MR11) . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Test Pattern Enable (MR12) . . . . . . . . . . . . . . . . . . . . . . 16
Test Pattern Hatch/Frame (MR13) . . . . . . . . . . . . . . . . . 16
VBI Open (MR14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Undershoot Limiter (MR15–MR16) . . . . . . . . . . . . . . . . 16
Sharpness Filter (MR17) . . . . . . . . . . . . . . . . . . . . . . . . . 16
MODE REGISTER 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MR1 (MR27–MR20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MR2 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 17
Y Delay (MR20–MR22) . . . . . . . . . . . . . . . . . . . . . . . . . 17
Color Delay (MR23–MR25) . . . . . . . . . . . . . . . . . . . . . . 17
CGMS Enable (MR26) . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CGMS CRC (MR27) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
–2–
REV. A
ADV7195
ADAPTIVE FILTER THRESHOLD A . . . . . . . . . . . . . . . 23
AFTA AFTA7–0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ADAPTIVE FILTER THRESHOLD B . . . . . . . . . . . . . . . 23
AFTB AFTB7–0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ADAPTIVE FILTER THRESHOLD C . . . . . . . . . . . . . . . 23
AFTC AFTC7–0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SHARPNESS FILTER AND ADAPTIVE FILTER
APPLICATIONS EXAMPLES . . . . . . . . . . . . . . . . . . . . 24
Sharpness Filter Application . . . . . . . . . . . . . . . . . . . . . . 24
Adaptive Filter Control Application . . . . . . . . . . . . . . . . . 25
HDTV MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MODE REGISTER 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MR0 (MR07–MR00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MR0 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 26
Output Standard Selection (MR00-MR01) . . . . . . . . . . . 26
Input Control Signals (MR02–MR03) . . . . . . . . . . . . . . . 26
Reserved (MR04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Input Standard (MR05) . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DV Polarity (MR06) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Reserved (MR07) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MODE REGISTER 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MR1 (MR17–MR10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MR1 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 27
Pixel Data Enable (MR10) . . . . . . . . . . . . . . . . . . . . . . . . 27
Input Format (MR11) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Test Pattern Enable (MR12) . . . . . . . . . . . . . . . . . . . . . . 27
Test Pattern Hatch/Frame (MR13) . . . . . . . . . . . . . . . . . 27
VBI Open (MR14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Reserved (MR15–MR17) . . . . . . . . . . . . . . . . . . . . . . . . . 27
MODE REGISTER 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MR1 (MR27–MR20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MR2 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 28
Y Delay (MR20–MR22) . . . . . . . . . . . . . . . . . . . . . . . . . 28
REV. A
Color Delay (MR23–MR25) . . . . . . . . . . . . . . . . . . . . . . 28
Reserved (MR26–MR27) . . . . . . . . . . . . . . . . . . . . . . . . . 28
MODE REGISTER 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MR3 (MR37–MR30) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MR3 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 28
HDTV Enable (MR30) . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Reserved (MR31–MR32) . . . . . . . . . . . . . . . . . . . . . . . . . 28
DAC A Control (MR33) . . . . . . . . . . . . . . . . . . . . . . . . . 28
DAC B Control (MR34) . . . . . . . . . . . . . . . . . . . . . . . . . 28
DAC C Control (MR35) . . . . . . . . . . . . . . . . . . . . . . . . . 28
Reserved (MR36–MR37) . . . . . . . . . . . . . . . . . . . . . . . . . 28
MODE REGISTER 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MR4 (MR47–MR40) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MR4 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 29
Timing Reset (MR40) . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Reserved (MR41–MR47) . . . . . . . . . . . . . . . . . . . . . . . . . 29
MODE REGISTER 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MR5 (MR57–MR50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MR5 BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 29
Reserved (MR50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
RGB Mode (MR51) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Sync on PrPb (MR52) . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Color Output Swap (MR53) . . . . . . . . . . . . . . . . . . . . . . 29
Reserved (MR54–MR57) . . . . . . . . . . . . . . . . . . . . . . . . . 29
DAC TERMINATION AND LAYOUT
CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PC BOARD LAYOUT CONSIDERATIONS . . . . . . . . . . 30
Supply Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Digital Signal Interconnect . . . . . . . . . . . . . . . . . . . . . . . . 31
Analog Signal Interconnect . . . . . . . . . . . . . . . . . . . . . . . 31
Video Output Buffer and Optional Output Filter . . . . . . . 31
OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 36
–3–
ADV7195–SPECIFICATIONS
3.3 V SPECIFICATIONS
(VAA = 3.15 V to 3.45 V, VREF = 1.235 V, RSET = 2470 , RLOAD = 300 . All specifications TMIN to TMAX [0C
to 70C] unless otherwise noted, TJMAX = 110C.)
Parameter
Min
STATIC PERFORMANCE
Resolution (Each DAC)
Integral Nonlinearity1
Differential Nonlinearity1
Typ
11
1.5
0.9
DIGITAL OUTPUTS
Output Low Voltage, VOL
Output High Voltage, VOH
Three-State Leakage Current
Three-State Output Capacitance
Max
Unit
2.0
Bits
LSB
LSB
0.4
V
V
µA
pF
2.4
10
4
DIGITAL AND CONTROL INPUTS
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current, IIN
Input Capacitance, CIN
2
V
V
µA
pF
0.8
0
4
0.65
4.25
2.83
4.25
2.66
1.4
1.4
100
7
4.56
3.11
4.56
2.93
mA
mA
mA
mA
%
V
kΩ
pF
1.235
1.359
V
25
51
40
35
60
mA
mA
mA
IAA3, 4
11
15
mA
IPLL
6.0
12
mA
Power Supply Rejection Ratio
0.01
ANALOG OUTPUTS
Full-Scale Output Current
3.92
2.54
3.92
2.39
Output Current Range
DAC-to-DAC Matching
Output Compliance Range, VOC
Output Impedance, ROUT
Output Capacitance, COUT
0
VOLTAGE REFERENCE (External)
Reference Range, VREF
1.112
POWER REQUIREMENTS
IDD2
Test Conditions
ISINK = 3.2 mA
ISOURCE = 400 µA
VIN = 0.4 V
VIN = 0.0 V or VDD
DAC A
DAC B, DAC C
DAC A
DAC B, DAC C
1× Interpolation
2× Interpolation
HDTV Mode
(With fCLK = 7425 MHz)
1× Interpolation,
2× Interpolation, and
HDTV Mode
1× Interpolation,
2× Interpolation, and
HDTV Mode
%/%
NOTES
1
Guaranteed by characterization.
2
IDD or the circuit current is the continuous current required to drive the digital core without I PLL.
3
IAA is the total current required to supply all DACs, including the V REF circuitry.
4
All DACs On.
Specifications subject to change without notice.
3 V DYNAMIC–SPECIFICATIONS
Parameter
Luma Bandwidth
Chroma Bandwidth
Signal-to-Noise Ratio
Chroma/Luma Delay Inequality
Min
(VAA = 3.15 V to 3.45 V, VREF = 1.235 V, RSET = 2470 , RLOAD = 300 . All specifications
TMIN to TMAX [0C to 70C] unless otherwise noted.)
Typ
13.5
6.75
64
0
Max
Unit
MHz
MHz
dB Luma Ramp Unweighted
ns
Specifications subject to change without notice.
–4–
REV. A
ADV7195
3.3 V TIMING–SPECIFICATIONS
Parameter
Min
(VAA = 3.15 V to 3.45 V, VREF = 1.235 V, RSET = 2470 , RLOAD = 300 . All specifications
TMIN to TMAX [0C to 70C] unless otherwise noted.)
Typ
Max
Unit
400
kHz
µs
µs
µs
µs
ns
ns
ns
µs
ns
Conditions
1
MPU PORT
SCLOCK Frequency
SCLOCK High Pulsewidth, t1
SCLOCK Low Pulsewidth, t 2
Hold Time (Start Condition), t 3
Setup Time (Start Condition), t 4
Data Setup Time, t5
SDATA, SCLOCK Rise Time, t 6
SDATA, SCLOCK Fall Time, t7
Setup Time (Stop Condition), t 8
RESET Low Time
0
0.6
1.3
0.6
0.6
100
300
300
0.6
100
ANALOG OUTPUTS
Analog Output Delay, t62
Analog Output Skew
CLOCK CONTROL AND PIXEL PORT 3
fCLK
Clock High Time, t9
Clock Low Time, t10
Data Setup Time, t11
Data Hold Time, t 12
Control Setup Time, t 11
Control Hold Time, t 12
Pipeline Delay
Pipeline Delay
5.0
5.0
2.0
4.5
7.0
4.0
16
29
10
0.5
ns
ns
27
74.25
81
21.5
22.0
3.4
3.2
3.4
3.2
MHz
MHz
MHz
ns
ns
ns
ns
ns
ns
Clock Cycles
Clock Cycles
After this Period the 1st Clock Is Generated
Relevant for Repeated Start Condition
Progressive Scan Mode
HDTV Mode
ASYNC Timing Mode and 1× Interpolation
For 4:4:4 Pixel Input Format at 1× Oversampling
For 4:4:4 or 4:2:2 Pixel Input Format at
2× Oversampling
NOTES
1
Guaranteed by characterization.
2
Output delay measured from 50% point of rising edge of CLOCK to the 50% point of DAC output full-scale transition.
3
Data: Cb/Cr(9–0), Cr(9–0), Y(9–0); Control: HSYNC/SYNC, VSYNC/TSYNC, DV.
Specifications subject to change without notice.
REV. A
–5–
ADV7195
CLOCK
t9
PIXEL INPUT
DATA
t10
R0
R1
R2
G0
G1
G2
B0
B1
B2
Rxxx
Rxxx
G3
Gxxx
Gxxx
B3
Bxxx
Bxxx
t12
t9 - CLOCK HIGH TIME
t10 - CLOCK LOW TIME
t11 - DATA SETUP TIME
t12 - DATA HOLD TIME
t11
Figure 1. 4:4:4 RGB Input Data Format Timing Diagram
CLOCK
t9
PIXEL INPUT
DATA
t10
Y0
Y1
Y2
Cb0
Cr0
Cb1
Cr1
Yxxx
Yxxx
Cbxxx
Crxxx
t12
t9 - CLOCK HIGH TIME
t10 - CLOCK LOW TIME
t11 - DATA SETUP TIME
t12 - DATA HOLD TIME
t11
Figure 2. 4:2:2 Input Data Format Timing Diagram
CLOCK
t9
PIXEL INPUT
DATA
t10
Y0
Y1
Y2
Cb0
Cb1
Cb2
Cr0
Cr1
Cr2
Yxxx
Yxxx
Cb3
Cbxxx
Cbxxx
Cr3
Crxxx
Crxxx
t12
t9 - CLOCK HIGH TIME
t10 - CLOCK LOW TIME
t11 - DATA SETUP TIME
t12 - DATA HOLD TIME
t11
Figure 3. 4:4:4 YCrCb Input Data Format Timing Diagram
–6–
REV. A
ADV7195
HSYNC
VSYNC
A
DV
PIXEL
DATA
Y
Y
Y
Y
Cr
Cr
Cr
Cr
Cb
Cb
Cb
Cb
B
AMIN = 16 CLK CYCLES (525P)
BMIN = 122 CLK CYCLES (525P)
AMIN = 12 CLK CYCLES (625P)
BMIN = 132 CLK CYCLES (625P)
AMIN = 44 CLK CYCLES (1080I)
BMIN = 236 CLK CYCLES (1080I)
AMIN = 70 CLK CYCLES (720P)
BMIN = 300 CLK CYCLES (720P)
Figure 4. Input Timing Diagram
t5
t3
t3
SDA
t6
t1
SCL
t2
t7
t4
Figure 5. MPU Port Timing Diagram
REV. A
–7–
t8
ADV7195
ABSOLUTE MAXIMUM RATINGS 1
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Analog Output Short Circuit to any Power Supply or Common can be of an
indefinite duration.
VAA to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage on Any Digital Pin . . . . GND – 0.5 V to VAA + 0.5 V
Ambient Operating Temperature (TA) . . . . . –40°C to +85°C
Storage Temperature (TS) . . . . . . . . . . . . . –65°C to +150°C
Infrared Reflow Soldering (20 sec) . . . . . . . . . . . . . . . 225°C
Vapor Phase Soldering (1 minute) . . . . . . . . . . . . . . . . 220°C
IOUT to GND2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to VAA
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
ADV7195KS
0°C to 70°C
Plastic Quad Flatpack
S-52
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADV7195 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
RESET
Cb/Cr[9]
ALSB
Cb/Cr[8]
Cb/Cr[7]
Cb/Cr[5]
Cb/Cr[6]
Cb/Cr[3]
Cb/Cr[4]
Cb/Cr[2]
Cb/Cr[1]
GND
Cb/Cr[0]
PIN CONFIGURATION
52 51 50 49 48 47 46 45 44 43 42 41 40
VDD 1
Y[0] 2
Y[1] 3
39 VREF
38 RSET
PIN 1
IDENTIFIER
37 COMP
Y[2] 4
Y[3] 5
36 DAC B
Y[4] 6
Y[5] 7
35 VAA
34 DAC A/Y OUTPUT
ADV7195
33 AGND
TOP VIEW
(Not to Scale)
Y[6] 8
Y[7] 9
32 DAC C
31 SDA
Y[8] 10
Y[9] 11
30 SCL
29 HSYNC/SYNC
28 VSYNC/TSYNC
VDD 12
GND 13
27 DV
–8–
AGND
VAA
CLKIN
Cr[8]
Cr[9]
Cr[6]
Cr[7]
Cr[5]
Cr[4]
Cr[3]
Cr[2]
Cr[0]
Cr[1]
14 15 16 17 18 19 20 21 22 23 24 25 26
REV. A
ADV7195
PIN FUNCTION DESCRIPTIONS
Pin
Mnemonic
Input/Output
Function
1, 12
2–11
VDD
Y0–Y9
P
I
13, 52
14–23
GND
Cr0–Cr9
G
I
24, 35
25
VAA
CLKIN
P
I
26, 33
27
28
G
I
I
30
31
32
34
36
37
38
AGND
DV
VSYNC/
TSYNC
HSYNC/
SYNC
SCL
SDA
DAC C
DAC A
DAC B
COMP
RSET
Digital Power Supply
10-Bit Progressive Scan/HDTV Input Port for Y Data. Input for G data when
RGB data is input.
Digital Ground
10-Bit Progressive Scan/HDTV Input Port for Color Data in 4:4:4 Input Mode.
In 4:2:2 mode this input port is not used. Input port for R data when RGB
data is input.
Analog Power Supply
Pixel Clock Input. Requires a 27 MHz reference clock for standard operation in
Progressive Scan Mode or a 74.25 MHz (74.1758 MHz) reference clock in
HDTV mode.
Analog Ground
Video Blanking Control Signal Input
VSYNC, Vertical Sync Control Signal Input or TSYNC Input Control Signal in
Async Timing Mode
HSYNC, Horizontal Sync Control Signal Input or SYNC Input Control Signal in
39
VREF
I/O
40
RESET
I
41
ALSB
I
42–51
Cb/Cr9–0
I
29
REV. A
I
Async Timing Mode
I
I/O
O
O
O
O
I
MPU Port Serial Interface Clock Input
MPU Port Serial Data Input/Output
Color Component Analog Output of Input Data on Cb/Cr9–0 Input Pins
Y Analog Output
Color Component Analog Output of Input Data on Cr9–Cr0 Input Pins
Compensation Pin for DACs. Connect 0.1 µF Capacitor from COMP pin to VAA.
A 2470 Ω resistor for input ranges 64–940 and 64–960 (output standards EIA770.1–EIA-770.3) must be connected from this pin to ground and is used to
control the amplitudes of the DAC outputs. For input ranges 0–1023 (output
standards RS-170, RS-343A) the RSET value must be 2820 Ω.
Optional External Voltage Reference Input for DACs or Voltage Reference Output (1.235 V)
This input resets the on-chip timing generator and sets the ADV7195 into Default
Register setting. Reset is an active low signal.
TTL Address Input. This signal sets up the LSB of the MPU address. When this
pin is tied high, the I2C filter is activated, which reduces noise on the I2C Interface.
When this pin is tied low, the input bandwidth on the I2C interface is increased.
10-Bit Progressive scan/HDTV input port for color data. In 4:2:2 mode the
multiplexed CrCb data must be input on these pins. Input port for B data when
RGB is input.
–9–
ADV7195
FUNCTIONAL DESCRIPTION
Digital Inputs
Control Signals
The digital inputs of the ADV7195 are TTL-compatible. 30-bit
YCrCb or RGB pixel data in 4:4:4 format or 20-bit YCrCb
pixel data in 4:2:2 format is latched into the device on the rising
edge of each clock cycle at 27 MHz in Progressive Scan Mode or
74.25 MHz or 74.1785 MHz in HDTV mode. It is also possible
to input 3 × bit RGB data in 4:4:4 format to the ADV7195. It
is recommended to input data in 4:2:2 mode to make use of the
chroma SSAFs on the ADV7195. As can be seen in Figures 6 and
7, this filter has 0 dB passband response and prevents signal components being loaded back into the frequency band. In 4:4:4 input
mode, the video data is already interpolated by the external
input device and the chroma SSAFs of the ADV7195 are bypassed.
ATTEN 10dB
RL –10.0dBm
VAVG
1
10dB/
MKR
0dB
3.18MHz
The ADV7195 accepts sync control signals accompanied by
valid 4:2:2 or 4:4:4 data. These external horizontal, vertical, and
blanking pulses (or EAV/SAV codes) control the insertion of
appropriate sync information into the output signals.
Analog Outputs
The analog Y signal is output on the 11-bit + Sync DAC A,
the color component analog signals on the 11-bit DAC B and
DAC C conforming to EIA-770.1 or EIA-770.2 standards in PS
mode or EIA-770.3 in HDTV mode. RSET has a value of 2470 Ω
(EIA-770.1, EIA-770.2, EIA-770.3), RLOAD has a value of 300 Ω.
For RGB outputs conforming to RS-170/RS-343A output standards RSET must have a value of 2820 Ω.
Undershoot Limiter
A limiter can be applied to the Y data before it is applied to the
DACs. Available limit values are –1.5 IRE, –6 IRE, –11 IRE below
blanking. This functionality is available in Progressive Scan
Mode only.
I2C Filter
A selectable internal I2C filter allows significant noise reductions
on the I2C interface. In setting ALSB high, the input bandwidth
on the I2C lines is reduced and pulses of less than 50 ns are not
passed to the I2C controller. Setting ALSB low allows greater
input bandwidth on the I2C lines.
Internal Test Pattern Generator
START 100kHz
RBW 10kHz
STOP
VBW 300Hz
20.00MHz
SWP 17.0SEC
Figure 6. ADV7195 SSAF Response to a 2.5 MHz Chroma
Sweep Using 4:2:2 Input Mode
ATTEN 10dB
RL –10.0dBm
VAVG
4
10dB/
MKR
–3.00dB
3.12MHz
The ADV7195 can generate a crosshatch pattern (white lines
against a black background). Additionally, the ADV7195 can
output a uniform color pattern. The color of the lines or uniform field/frame can be programmed by the user.
Y/CrCb Delay
The Y output and the color component outputs can be delayed
wrt the falling edge of the horizontal sync signal by up to four
clock cycles.
Gamma Correction
Gamma correction may be performed on the luma data. The
user has the choice to use either of two different gamma curves,
A or B. At any one time one of these curves is operational if
gamma correction is enabled. Gamma correction allows the
mapping of the luma data to a user-defined function.
54 MHz Operation
In Progressive Scan mode, it is possible to operate the three
output DACs at 54 MHz or 27 MHz. The ADV7195 is supplied with a 27 MHz clock synced with the incoming data. If
required, a second stage interpolation filter interpolates the data
to 54 MHz before it is applied to the three output DACs.
START 100kHz
RBW 10kHz
STOP
VBW
300Hz
20.00MHz
SWP
17.0SEC
Figure 7. Conventional Filter Response to a 2.5 MHz
Chroma Sweep Using 4:4:4 Input Mode
The second stage interpolation filter is controlled by MR36. After
applying a Reset, it is recommended to toggle this bit. Before
toggling this bit, 3Ehex must be written to Address 09hex.
PROGRAMMABLE SHARPNESS FILTER
Sharpness Filter Mode is applicable to the Y data only in
Progressive Scan Mode.
The desired frequency response can be chosen by the user in
programming the correct value via the I2C. The variation of
frequency responses can be seen in the figures on the following pages.
–10–
REV. A
ADV7195
PROGRAMMABLE ADAPTIVE FILTER CONTROL
10
If the Adaptive Filter Mode is enabled (Progressive Scan Mode
only), it is possible to compensate for large edge transitions on
the incoming Y data. Sensitivity and attenuation are all programmable over the I2C. For further information refer to
Sharpness Filter Control and Adaptive Filter Control section.
0
–10
–20
–30
INPUT/OUTPUT CONFIGURATION
–40
Table I shows possible input/output configurations when using
the ADV7195.
–50
Table I.
–60
Input Format
–70
Output
YCrCb Progressive Scan
4:2:2
4:4:4
YCrCb HDTV
4:2:2
4:4:4
RGB Progressive Scan
4:4:4
RGB HDTV
4:4:4
Async Timing Mode
All Inputs
–80
5
0
2×
1× or 2×
10
15
20
30
25
Figure 10. Interpolation Filter–CrCb Channels/Cr 4:4:4
Input Data
1×
1×
MPU PORT DESCRIPTION
The ADV7195 support a 2-wire serial (I2C-compatible) microprocessor bus driving multiple peripherals. Two inputs, Serial
Data (SDA) and Serial Clock (SCL) carry information between
any device connected to the bus. Each slave device is recognized
by a unique address. The ADV7195 has four possible slave
addresses for both read and write operations. These are unique
addresses for each device and are illustrated in Figure 11. The
LSB sets either a read or write operation. Logic Level “1” corresponds to a read operation while Logic Level “0” corresponds to
a write operation. A1 is set by setting the ALSB pin of the
ADV7195 to Logic Level “0” or Logic Level “1.” When ALSB is
set to “0,” there is greater input bandwidth on the I2C lines,
which allows high-speed data transfers on this bus. When ALSB
is set to “1,” there is reduced input bandwidth on the I2C
lines, which means that pulses of less than 50 ns will not pass
into the I2C internal controller. This mode is recommended
for noisy systems.
2×
1×
1×
10
0
–10
–20
–30
–40
–50
–60
1
1
0
1
0
1
A1
X
–70
–80
0
5
10
15
20
25
ADDRESS
CONTROL
SETUP BY
ALSB
30
Figure 8. 2× Interpolation Filter 4-Channel
READ/WRITE
CONTROL
0
WRITE
1
READ
10
Figure 11. Slave Address
0
–10
–20
–30
–40
–50
–60
–70
–80
0
5
10
15
20
25
30
Figure 9. Interpolation Filter–CrCb Channels/Cr 4:2:2
Input Data
REV. A
To control the various devices on the bus the following protocol
must be followed. First the master initiates a data transfer by
establishing a Start condition, defined by a high-to-low transition on SDA while SCL remains high. This indicates that an
address/data stream will follow. All peripherals respond to the
Start condition and shift the next eight bits (7-bit address + R/W
bit). The bits are transferred from MSB down to LSB. The
peripheral that recognizes the transmitted address responds by
pulling the data line low during the ninth clock pulse. This is
known as an acknowledge bit. All other devices withdraw from
the bus at this point and maintain an idle condition. The idle
condition is where the device monitors the SDA and SCL lines
waiting for the Start condition and the correct transmitted
address. The R/W bit determines the direction of the data.
–11–
ADV7195
in autoincrement mode, the user exceeds the highest subaddress,
the following action will be taken:
A Logic “0” on the LSB of the first byte means that the master
will write information to the peripheral. A Logic “1” on the LSB
of the first byte means that the master will read information
from the peripheral.
1. In Read Mode, the highest subaddress register contents
will continue to be output until the master device issues a
no-acknowledge. This indicates the end of a read. A noacknowledge condition is where the SDA line is not pulled
low on the ninth pulse.
The ADV7195 acts as a standard slave device on the bus. The
data on the SDA pin is 8 bits long supporting the 7-bit addresses
plus the R/W bit. It interprets the first byte as the device address
and the second byte as the starting subaddress. The subaddresses
autoincrement, allowing data to be written to or read from the
starting subaddress. A data transfer is always terminated by a
Stop condition. The user can also access any unique subaddress
register on a one-by-one basis without having to update all the
registers.
2. In Write Mode, the data for the invalid byte will not be
loaded into any subaddress register, a no-acknowledge will
be issued by the ADV7195 and the part will return to the idle
condition.
SDATA
Stop and Start conditions can be detected at any stage during
the data transfer. If these conditions are asserted out of sequence
with normal read and write operations, they cause an immediate
jump to the idle condition. During a given SCL high period the
user should issue only one Start condition, one Stop condition
or a single Stop condition followed by a single Start condition. If
an invalid subaddress is issued by the user, the ADV7195 will
not issue an acknowledge and will return to the idle condition. If
WRITE
SEQUENCE
S
SLAVE ADDR A(S)
SUB ADDR
S
SLAVE ADDR A(S)
S = START BIT
P = STOP BIT
S
1 7
8
9
1 7
8
9
1 7
START ADDR R/W ACK SUBADDRESS ACK
DATA
8
9
P
ACK
STOP
Figure 12. Bus Data Transfer
Figure 12 illustrates an example of data transfer for a read sequence
and the Start and Stop conditions.
Figure 13 shows bus write and read sequences.
DATA
A(S)
DATA
A(S) P
LSB = 1
LSB = 0
READ
SEQUENCE
A(S)
SCLOCK
SUB ADDR
A(S) S SLAVE ADDR
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
A(S)
DATA
A(M)
DATA
A(M) P
A(S) = NO ACKNOWLEDGE BY SLAVE
A(M) = NO ACKNOWLEDGE BY MASTER
Figure 13. Write and Read Sequence
–12–
REV. A
ADV7195
REGISTER ACCESSES
Subaddress Register (SR7–SR0)
The MPU can write to or read from all of the registers of the
ADV7195 except the Subaddress Registers, which are write-only
registers. The Subaddress Register determines which register the
next read or write operation accesses.
The Communications Register is an 8-bit write-only register.
After the part has been accessed over the bus and a read/
write operation is selected, the subaddress is set up. The Subaddress Register determines to/from which register the
operation takes place.
All communications with the part through the bus begin with an
access to the Subaddress Register. A read/write operation is
performed from/to the target address which then increments to
the next address until a Stop command on the bus is performed.
Figure 14 shows the various operations under the control of the
Subaddress Register. “0” should always be written to SR7.
Register Select (SR6–SR0)
These bits are set up to point to the required starting address.
REGISTER PROGRAMMING
The following section describes the functionality of each register. All registers can be read from as well as written to unless
otherwise stated.
SR7
SR6
SR5
SR4
SR3
SR2
SR1
SR0
ADV7195 SUBADDRESS REGISTER
SR7
ZERO SHOULD
BE WRITTEN
HERE
ADDRESS
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
27h
SR6 SR5 SR4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
SR3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
SR2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
SR1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
SR0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
MODE REGISTER 0
MODE REGISTER 1
MODE REGISTER 2
MODE REGISTER 3
MODE REGISTER 4
MODE REGISTER 5
COLOR Y
COLOR CR
COLOR CB
MODE REGISTER 6
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
FILTER GAIN
CGMS DATA REGISTER 0
CGMS DATA REGISTER 1
CGMS DATA REGISTER 2
GAMMA CORRECTION REGISTER 0
GAMMA CORRECTION REGISTER 1
GAMMA CORRECTION REGISTER 2
GAMMA CORRECTION REGISTER 3
GAMMA CORRECTION REGISTER 4
GAMMA CORRECTION REGISTER 5
GAMMA CORRECTION REGISTER 6
GAMMA CORRECTION REGISTER 7
GAMMA CORRECTION REGISTER 8
GAMMA CORRECTION REGISTER 9
GAMMA CORRECTION REGISTER 10
GAMMA CORRECTION REGISTER 11
GAMMA CORRECTION REGISTER 12
GAMMA CORRECTION REGISTER 13
ADAPTIVE FILTER GAIN 1
ADAPTIVE FILTER GAIN 2
ADAPTIVE FILTER GAIN 3
ADAPTIVE FILTER THRESHOLD A
ADAPTIVE FILTER THRESHOLD B
ADAPTIVE FILTER THRESHOLD C
Figure 14. Subaddress Registers in Progressive Scan Mode
SR7
SR7
ZERO SHOULD
BE WRITTEN
HERE
SR6
SR5
SR4
SR3
SR2
SR1
ADV7195 SUBADDRESS REGISTER
ADDRESS
00h
01h
02h
03h
04h
05h
06h
07h
08h
SR6 SR5 SR4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SR3
0
0
0
0
0
0
0
0
1
SR2
0
0
0
0
1
1
1
1
0
SR1
0
0
1
1
0
0
1
1
0
SR0
0
1
0
1
0
1
0
1
0
MODE REGISTER 0
MODE REGISTER 1
MODE REGISTER 2
MODE REGISTER 3
MODE REGISTER 4
MODE REGISTER 5
COLOR Y
COLOR CR
COLOR CB
Figure 15. Subaddress Registers in HDTV Mode
REV. A
SR0
–13–
ADV7195
PROGRESSIVE SCAN MODE
Input Control Signals (MR02–MR03)
MODE REGISTER 0
MR0 (MR07–MR00)
(Address (SR4–SR0) = 00H)
These control bits are used to select whether data is input with
external horizontal, vertical and blanking sync signals or if the
data is input with embedded EAV/SAV codes.
Figure 16 shows the various operations under the control of
Mode Register 0.
An Asynchronous timing mode is also available using TSYNC,
SYNC and DV as input control signals. These control signals
have to be programmed by the user.
MR0 BIT DESCRIPTION
Output Standard Selection (MR00–MR01)
These bits are used to select the output levels for the ADV7195.
If EIA-770.2 (MR01–00 = “00”) is selected, the output levels
will be: 0 mV for blanking level, 700 mV for peak white for the Y
channel, ± 350 mV for Pr, Pb outputs and –300 mV for Sync.
Sync insertion on the Pr, Pb channels is optional.
If EIA-770.1 (MR01–00 = “01”) is selected, the output levels
will be: 0 mV for blanking level, 714 mV for peak white for the Y
channel, ± 350 mV for Pr, Pb outputs and –286 mV for Sync.
Optional sync insertion on the Pr, Pb channels is not possible.
If Full I/P Range (MR01–00 = “10”) is selected, the output
levels will be: 0 mV for blanking level, 700 mV for peak white for
the Y channel, ± 350 mV for Pr, Pb outputs and –300 mV for
Sync. Sync insertion on the Pr, Pb channels is optional. This
mode is used for RS-170, RS-343A standard output compatibility. Refer to Figures 61 to 64 for output level plots.
MR07
MR06
MR05
MR04
MR07
MR05
ZERO MUST
BE WRITTEN
TO THIS BIT
ZERO MUST
BE WRITTEN
TO THIS BIT
INPUT
STANDARD
Figure 17 shows an example of how to program the ADV7195
to accept a different high definition standard but SMPTE293M,
SMPTE274M, SMPTE296M or ITU-R.BT1358 standard.
Input Standard (MR04)
Select between 525p progressive scan input or 625p progressive
scan input.
Reserved (MR05)
A “0” must be written to this bit.
DV Polarity (MR06)
This control bit allows the user to select the polarity of the DV
input control signal to be either active high or active low. This is
in order to facilitate interfacing from I to P Converters which
use an active low blanking signal output.
Reserved (MR07)
A “0” must be written to this bit.
MR03
MR04
0
525P
1
625P
MR02
MR01
MR00
INPUT CONTROL SIGNALS
MR03 MR02
0
0
1
1
0
1
0
1
HSYNC/VSYNC/DV
EAV/SAV
TSYNC/SYNC/DV
RESERVED
DV POLARITY
MR06
0
ACTIVE HIGH
1
ACTIVE LOW
OUTPUT STANDARD SELECTION
MR01 MR00
0
0
1
1
0
1
0
1
EIA-770.2
EIA-770.1
FULL I/P RANGE
RESERVED
Figure 16. Mode Register 0
–14–
REV. A
ADV7195
Table II must be followed when programming the control signals in Async Timing Mode.
Table II. Truth Table
SYNC
TSYNC
DV
1 –> 0
0
0 or 1
0
0 –> 1
0 or 1
0 –> 1
0 or 1
0
1
1
0 or 1
0 or 1
0 –> 1
1 –> 0
50% Point of Falling Edge of
Tri-Level Horizontal Sync
Signal, A
25% Point of Rising Edge of
Tri-Level Horizontal Sync
Signal, B
50% Point of Falling Edge of
Tri-Level Horizontal Sync
Signal, C
50% Start of Active Video, D
50% End of Active Video, E
CLK
SYNC
PROGRAMMABLE
INPUT TIMING
TSYNC
DV
SET MR06 = 1
HORIZONTAL SYNC
81
66
66
A
B
ACTIVE VIDEO
243
ANALOG
OUTPUT
1920
C
D
E
Figure 17. Async Timing Mode—Programming Input Control Signals for SMPTE295M Compatibility
525
VIDEO
OUTPUT
1
12
13
HSYNC
VSYNC
DV
Figure 18. DV Input Control Signal in Relation to Video Output Signal
REV. A
–15–
42
43
ADV7195
MODE REGISTER 1
MR1 (MR17–MR10)
(Address (SR4–SR0) = 01H)
VBI Open (MR14)
Figure 20 shows the various operations under the control of
Mode Register 1.
For this purpose Lines 13 to 42 of each frame can be used for
VBI when SMPTE293M standard is used, or Lines 6 to 43
when ITU-R.BT1358 standard is used.
This bit enables or disables the facility of VBI data insertion
during the Vertical Blanking Interval.
MR1 BIT DESCRIPTION
Pixel Data Enable (MR10)
Undershoot Limiter (MR15–MR16)
When this bit is set to “0,” the pixel data input to the ADV7195
is blanked such that a black screen is output from the DACs.
When this bit is set to “1,” pixel data is accepted at the input
pins and the ADV7195 outputs the standard set in “Output
Standard Selection” (MR01–00). This bit also must be set to
“1” to enable output of the test pattern signals.
This control limits the Y signal to a programmable level
in the active video region.
Available limit levels are –1.5 IRE, –6 IRE, –11 IRE.
Note that this facility is only available when Interpolation is
enabled (MR36 = “1”).
Input Format (MR11)
Sharpness Filter (MR17)
It is possible to input data in 4:2:2 format or at 4:4:4 format at
27 MHz.
This control bit enables or disables the Sharpness Filter Mode.
This bit must be set to “1” for any values programmed into the
Filter Gain Register to take effect. It must also be set to “1” when
Adaptive Filter mode is used.
Test Pattern Enable (MR12)
Enables or disables the internal test pattern generator.
Refer to Sharpness Filter Control and Adaptive Filter
Control section.
Test Pattern Hatch/Frame (MR13)
If this bit is set to “0,” a crosshatch test pattern is output from
the ADV7195 (for example, in SMPTE293M, 11 horizontal
and 11 vertical white lines, four pixels wide are displayed against
a black background). The crosshatch test pattern can be used to
test monitor convergence. If this bit is set to “1,” a uniform
colored frame/field test pattern is output from the ADV7195.
100 IRE
0 IRE
–6 IRE
The color of the lines or the frame/field is by default white but
can be programmed to be any color using the Color Y, Color
Cr, Color Cb registers.
MR17
MR16
MR15
–40 IRE
Figure 19. Undershoot Limiter, Programmed to –6 IRE
MR14
MR13
MR12
MR11
MR10
SHARPNESS
FILTER
VBI OPEN
TEST PATTERN
ENABLE
PIXEL DATA
ENABLE
MR17
0
DISABLE
1
ENABLE
MR14
0
DISABLE
1
ENABLE
MR12
0
DISABLE
1
ENABLE
MR10
0
DISABLE
1
ENABLE
UNDERSHOOT
LIMITER
MR16 MR15
0
0
0
1
1
0
1
1
DISABLE
–11 IRE
–6 IRE
–1.5 IRE
TEST PATTERN
HATCH/FRAME
MR13
0
HATCH
1
FIELD/FRAME
INPUT FORMAT
MR11
0
1
4:4:4 Y Cr Cb
4:2:2 Y Cr Cb
Figure 20. Mode Register 1
–16–
REV. A
ADV7195
MODE REGISTER 2
MR1 (MR27–MR20)
(Address (SR4–SR0) = 02H)
The CGMS data bits are programmed into the CGMS Data
Registers 0–2. For more information refer to CGMS Data
Registers section.
Figure 22 shows the various operations under the control of
Mode Register 2.
CGMS CRC (MR27)
This bit enables the automatic Cyclic Redundancy Check when
CGMS is enabled.
MR2 BIT DESCRIPTION
Y Delay (MR20–MR22)
This control bit delays the Y signal with respect to the falling
edge of the horizontal sync signal by up to four pixel clock
cycles. Figure 21 demonstrates this facility.
NO DELAY
Y OUTPUT
Y DELAY
MAX DELAY
Color Delay (MR23–MR25)
This control allows delay of the color signals with respect to the
falling edge of the horizontal sync signal by up to four pixel
clock cycles. Figure 21 demonstrates this facility.
NO DELAY
CGMS Enable (MR26)
MR27
MR26
CGMS ENABLE
MR26
0
DISABLE
1
ENABLE
CGMS CRC
MR25
MR24
MAX
DELAY
Figure 21. Y and Color Delay
MR23
MR22
COLOR DELAY
MR25 MR24 MR23
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
0 PCLK
1 PCLK
2 PCLK
3 PCLK
4 PCLK
MR27
0
DISABLE
1
ENABLE
Figure 22. Mode Register 2
REV. A
–17–
PrPb OUTPUT
PrPb DELAY
When this bit is set to “1,” CGMS data is inserted on Line
41 in 525p mode. The CGMS conforms to CGMS-A EIA-J
CPR1204-1, Transfer Method of Video ID information using
vertical blanking interval (525p System), March 1998 and
IEC61880, 1998, video systems (525/60)—video and accompanied
data using the vertical blanking interval—analog interface.
MR21
MR20
Y DELAY
MR22 MR21 MR20
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
0 PCLK
1 PCLK
2 PCLK
3 PCLK
4 PCLK
ADV7195
MODE REGISTER 3
MR3 (MR37–MR30)
(Address (SR4–SR0) = 03H)
MODE REGISTER 4
MR4 (MR47–MR40)
(Address (SR4–SR0) = 04H)
Figure 23 shows the various operations under the control of
Mode Register 3.
Figure 24 shows the various operations under the control of
Mode Register 4.
MR4 BIT DESCRIPTION
Timing Reset (MR40)
MR3 BIT DESCRIPTION
HDTV Enable (MR30)
When this bit is set to “1,” the ADV7195 reverts to HDTV mode
(refer to HDTV mode section). When set to “0” the ADV7195
is set up in Progressive Scan Mode (PS Mode).
Reserved (MR31–MR32)
A “0” must be written to these bits.
Toggling MR40 from low to high and low again resets the internal horizontal and vertical timing counters.
MODE REGISTER 5
MR5 (MR57–MR50)
(Address (SR4-SR0) = 05H)
Figure 25 shows the various operations under the control of
Mode Register 5.
DAC A Control (MR33)
Setting this bit to “1” enables DAC A, otherwise this DAC is
powered down.
MR5 BIT DESCRIPTION
Reserved (MR50)
DAC B Control (MR34)
Setting this bit to “1” enables DAC B, otherwise this DAC is
powered down.
This bit is reserved for the revision code.
RGB Mode (MR51)
DAC C Control (MR35)
Setting this bit to “1” enables DAC C, otherwise this DAC is
powered down.
When RGB mode is enabled (MR51 = “1”) the ADV7195
accepts unsigned binary RGB data at its input port. This control
is also available in Async Timing Mode.
Interpolation (MR36)
Sync on PrPb (MR52)
This bit enables the second stage interpolation filters. When this
bit is enabled (MR36 = “1”), data is sent at 54 MHz to the DAC
output stage. After Reset it is recommended to toggle this bit.
Before toggling this bit, 3Ehex must be written to address 09hex
to guarantee correct operation.
By default, the color component output signals Pr, Pb do not
contain any horizontal sync pulses. They can be inserted when
MR52 = “1.” This facility is only available when Output Standard Selection has been set to EIA-770.2 (MR01–00 = “00”) or
Full Input Range (MR01–00 = “10”).
Reserved (MR37)
This control is not available in RGB mode.
A “0” must be written to this bit.
MR37
MR36
MR35
MR34
MR33
MR32
MR31
MR37
DAC B CONTROL
MR32
ZERO MUST BE
WRITTEN TO
THIS BIT
MR34
0
POWER-DOWN
1
NORMAL
ZERO MUST BE
WRITTEN TO
THIS BIT
INTERPOLATION
MR36
0
DISABLE
1
ENABLE
MR30
HDTV ENABLE
MR30
0
DISABLE
1
ENABLE
DAC C CONTROL
DAC A CONTROL
MR31
MR35
0
POWER-DOWN
1
NORMAL
MR33
0
POWER-DOWN
1
NORMAL
ZERO MUST BE
WRITTEN TO
THIS BIT
Figure 23. Mode Register 3
MR47
MR46
MR45
MR44
MR43
MR42
MR47 – MR41
MR41
MR40
TIMING RESET
ZERO MUST BE
WRITTEN TO
THESE BITS
MR40
Figure 24. Mode Register 4
–18–
REV. A
ADV7195
MR57
MR56
MR55
MR54
ADAPTIVE MODE
CONTROL
MR57
0
MODE A
1
MODE B
MR52
COLOR OUTPUT
SWAP
MR53
MR56
0
MODE A
1
MODE B
ADAPTIVE FILTER
CONTROL
MR53
0
1
GAMMA
CORRECTION
MR55
0
DISABLE
1
ENABLE
RGB MODE
SYNC ON PrPb
MR52
0
DISABLE
1
ENABLE
MR54
0
CURVE A
1
CURVE B
MR50
MR51
0
DISABLE
1
ENABLE
DAC B = Pr
DAC C = Pr
GAMMA CURVE
MR51
MR50
RESERVED FOR
REVISION CODE
Figure 25. Mode Register 5
Color Output Swap (MR53)
Adaptive Filter Control (MR57)
By default, DAC B is configured as the Pr output and DAC
C as the Pb output. In setting this bit to “1” the DAC outputs can be swapped around so that DAC B outputs Pb and
DAC C outputs Pr. Table III demonstrates this in more detail.
This control is also available in RGB mode.
This bit enables the Adaptive Filter Control when set to “1.”
Sharpness Filter must be enabled as well (MR17 = “1”). The
Adaptive Filter Controls is explained in more detail under
Sharpness Filter Control and Adaptive Filter Control section.
Table III. Relationship Between Color Input Pixel Port, MR53
and DAC B, DAC C Outputs
COLOR Y
CY (CY7–CY0)
(Address (SR4–SR0) = 06H)
In 4:4:4 Input Mode
Color Data
Input on Pins
Cr9–0
Cb/Cr9–0
Cr9-0
Cb/Cr9–0
CY7
MR53
CY6
0
0
1
1
DAC B
DAC C
DAC C
DAC B
Color Data
Input on Pins
MR53
Analog Output
Signal
Cr9–0
Cb/Cr9–0
Cb/Cr9–0
0 or 1
0
1
Not Operational
DAC C (Pb)
DAC C (Pr)
In 4:2:2 Input Mode
This bit selects which of the two programmable gamma curves
is to be used. When setting MR54 to “0,” the gamma correction
curve selected is Curve A. Otherwise Curve B is selected. Each
curve will have to be programmed by the user as explained in
the Gamma Correction Registers section.
Adaptive Mode Control (MR56)
For this control to be effective, Adaptive Filter Control must be
enabled (MR57 = “1”) as well as the Sharpness Filter (MR17 =
“1”). For filter plots, refer to Sharpness Filter Control and
Adaptive Filter Control section.
CY3
CY2
CY1
CY0
CCR1
CCR0
CCB1
CCB0
CY7 – CY0
Figure 26. Color Y Register
COLOR CR
CCR (CCR7–CCR0)
(Address (SR4–SR0) = 07H)
CCR7
CCR6
CCR5
CCR4
CCR3
CCR2
CCR7 – CCR0
COLOR CR VALUE
Figure 27. Color Cr Register
COLOR CB
CCB (CCB7–CCB0)
(Address (SR4–SR0) = 08H)
CCB7
Gamma Correction (MR55)
To enable Gamma Correction, and therefore activate the gamma
curve programmed by the user, this bit must be set to “1.” Otherwise the programmable Gamma Correction facility is bypassed.
Programming of the gamma correction curves is explained in
the Gamma Correction Registers section.
CY4
COLOR Y VALUE
Gamma Curve (MR54)
REV. A
CY5
Analog Output
Signal
CCB6
CCB5
CCB4
CCB3
CCB2
CCB7 – CCB0
COLOR CB VALUE
Figure 28. Color Cb Register
These three 8-bit-wide registers are used to program the output
color of the internal test pattern generator, be it the lines of the
crosshatch pattern or the uniform field test pattern and are
available in PS mode and HDTV mode.
The standard used for the values for Y and the color difference
signals to obtain white, black and the saturated primary and
complementary colors conforms to the ITU-R BT 601-4 standard.
–19–
ADV7195
CGMS DATA REGISTERS 2–0
CGMS2 (CGMS27–CGMS20)
(Address (SR4–SR0) = 13H)
Table IV shows sample color values to be programmed into the
color registers when Output Standard Selection is set to
EIA-770.2 (MR01–00 = “00”).
This 8-bit-wide register contains the last four CGMS data bits,
(C16–C19) of the CGMS data stream.
Table IV. Sample Color Values for EIA-770.2 Output
Standard Selection
CGMS27 CGMS26 CGMS25 CGMS24 CGMS23 CGMS22 CGMS21 CGMS20
Sample
Color
Color Y
Value
Color Cr
Value
Color Cb
Value
White
Black
Red
Green
Blue
Yellow
Cyan
Magenta
235 (EB)
16 (10)
81 (51)
145 (91)
41 (29)
210 (D2)
170 (AA)
106 (6A)
128 (80)
128 (80)
240 (F0)
34 (22)
110 (6E)
146 (92)
16 (10)
222 (DE)
128 (80)
128 (80)
90 (5A)
54 (36)
240 (F0)
16 (10)
166 (A6)
202 (CA)
CGMS27 – CGMS24
CGMS23 – CGMS20
ZERO MUST BE
WRITTEN TO
THESE BITS
CGMS2
Figure 30. CGMS2 Data Register
CGMS1 (CGMS17–CGMS10)
(Address (SR4–SR0) = 12H)
This 8-bit-wide register contains C8–C15 of the CGMS
data stream.
MODE REGISTER 6
MR6 (MR67–MR60)
(ADDRESS (SR4–SR0) = 09H)
CGMS17 CGMS16 CGMS15 CGMS14 CGMS13 CGMS12 CGMS11 CGMS10
Figure 29 shows the various operations under the control of
Mode Register 6.
CGMS17 – CGMS10
CGMS1
MR6 BIT DESCRIPTION
MR67–MR60
Figure 31. CGMS1 Data Register
The value 3EHex must be written to this register before the PLL is
reset (reset MR36) to guarantee correct operation of the ADV7195.
MR67
MR66
MR65
MR64
MR63
MR62
MR61
This 8-bit-wide register contains the first eight CGMS data bits,
(C0–C7) of the CGMS data stream.
MR60
MR67
MR64
MR62
MR60
ZERO MUST BE
WRITTEN TO
THIS BIT
ONE MUST BE
WRITTEN TO
THIS BIT
ONE MUST BE
WRITTEN TO
THIS BIT
ZERO MUST BE
WRITTEN TO
THIS BIT
MR65
MR66
ONE MUST BE
WRITTEN TO
THIS BIT
ZERO MUST BE
WRITTEN TO
THIS BIT
CGMS0 (CGMS07–CGMS00)
(Address (SR4-SR0) = 11H)
MR63
MR61
ONE MUST BE
WRITTEN TO
THIS BIT
ZERO MUST BE
WRITTEN TO
THIS BIT
CGMS07 CGMS06 CGMS05 CGMS04 CGMS03 CGMS02 CGMS01 CGMS00
CGMS07 – CGMS00
CGMS0
Figure 32. CGMS0 Data Register
Figure 29. Mode Register 6
CRC SEQUENCE
+700mV
REF
70 10%
BIT1
C0
0mV
–300mV
BIT3
C1
BIT2
C2
BIT5
C3
C4
BIT4
BIT7
C5
BIT6
C6
BIT9
C7
C8
BIT8
BIT11
BIT15
BIT17
BIT19
C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19
BIT10
21.2s 0.22s
22T
5.8s 0.15s
6T
BIT13
BIT12
BIT14
BIT16
BIT18
BIT20
T = 1/(fH 33) = 963ns
fH = HORIZONTAL SCAN FREQUENCY
T 30ns
Figure 33. CGMS Waveform
–20–
REV. A
ADV7195
The response of the curve is programmed at seven predefined
locations. In changing the values at these locations the gamma
curve can be modified. Between these points linear interpolation is used to generate intermediate values. Considering the
curve to have a total length of 256 points, the seven locations
are at: 32, 64, 96, 128, 160, 192, 224.
FILTER GAIN
FG (FG7–FG0)
(Address (SR4–SR0) = 10H)
Figure 34 shows the various operations under the control of the
Filter Gain register.
FG7
FG6
FG5
FG4
FG3
FG2
FG1
FG7–FG4
FG3–FG0
FILTER GAIN B
FILTER GAIN A
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
FG0
Locations 0, 16, 240, and 255 are fixed and cannot be changed.
For the length of 16 to 240 the gamma correction curve has to
be calculated as below:
y = xγ
0
1
2
3
4
5
6
7
–8
–7
–6
–5
–4
–3
–2
–1
where
y = gamma corrected output.
x = linear input signal.
γ = gamma power factor.
To program the gamma correction registers, the seven values
for y have to be calculated using the following formula:
yn = [x(n–16)/(240 – 16)]γ × (240–16) + 16
where
x(n–16) = Value for x along x-axis at points:
n
= 32, 64, 96, 128, 160, 192, or 224.
= Value for y along the y-axis, which has to be written
yn
into the gamma correction register.
Figure 34. Filter Gain Register
FG BIT DESCRIPTION
Filter Gain A (FG3–FG0)
Example:
y32 = [(16/224)0.5 × 2 24] + 16 = 76*
y64 = [(48/224)0.5 × 224] + 16 =120*
y96 = [(80/224)0.5 × 224] + 16 = 150*
y128 = [(112/224)0.5 × 224] + 16 = 174*
These bits are used to program the gain A value, which varies
from response –8 to response +7 and are applied to Filter A.
Filter Gain B (FG4–FG7)
These bits are used to program the gain B value, which varies
from response –8 to response +7, and are applied to Filter B.
*Rounded to the nearest integer.
The above will result in a gamma curve shown on the next
page, assuming a ramp signal as an input.
Refer to Sharpness Filter Control and Adaptive Filter Control
section for more detail.
GAMMA CORRECTION REGISTERS 0–13
(GAMMA CORRECTION 0–13)
(Address (SR5–SR0) = 14H–21H)
300
GAMMA CORRECTION BLOCK OUTPUT
TO A RAMP INPUT
The Gamma Correction Registers are 14 8-bit-wide registers.
They are used to program the gamma correction Curves A and B.
Generally, gamma correction is applied to compensate for the
nonlinear relationship between signal input and brightness
level output (as perceived on the CRT). It can also be applied
wherever nonlinear processing is used.
Gamma correction uses the function:
SignalOUT = (Signal IN )γ
GAMMA-CORRECTED AMPLITUDE
0
1
2
3
4
5
6
7
–8
–7
–6
–5
–4
–3
–2
–1
250
SIGNAL OUTPUT
200
0.5
150
100
SIGNAL INPUT
50
where γ = gamma power factor.
0
Gamma correction is performed on the luma data only.
The user has the choice of two different curves, Curve A or
Curve B. At any one time only one of these curves can be used.
REV. A
0
50
100
150
LOCATION
200
250
Figure 35. Signal Input (Ramp) and Signal Output for
Gamma 0.5
–21–
ADV7195
INPUT SIGNAL: STEP
300
250
SHARPNESS AND ADAPTIVE FILTER CONTROL MODE
SIGNAL OUTPUTS
1.5
200
7
0.3
0.5
150
UT
NP
LI
A
1.5
GN
SI
100
6
5
1.3
4
3
2
1.8
50
0
1.4
1.2
MAGNITUDE
GAMMA-CORRECTED AMPLITUDE
GAMMA CORRECTION BLOCK OUTPUT
TO A RAMP INPUT FOR VARIOUS GAMMA VALUES
1.1
1
0
1.0
–1
0.9
–2
–3
0
50
100
150
LOCATION
200
250
Figure 36. Signal Input (Ramp) and Selectable Gamma
Output Curves
0.8
–4
0.7
–5
0.6
–6
–7
0.5
The gamma curves shown in Figure 36 are examples only, any
user-defined curve is acceptable in the range of 16–240.
SHARPNESS FILTER CONTROL AND ADAPTIVE
FILTER CONTROL
–8
0
2
4
6
8
FREQUENCY – MHz
10
12
1.5
7
1.4
Three Filter modes are available on the ADV7195: one Sharpness
Filter mode and two Adaptive Filter modes.
14
6
5
1.3
MAGNITUDE
SHARPNESS FILTER MODE
To enhance or attenuate the Y signal in the frequency ranges
shown in Figure 37, the following register settings must be used:
Sharpness Filter must be enabled (MR17 = “1”) and Adaptive
Filter Control must be disabled (MR57 = “0”).
4
1.2
3
1.1
1
2
0
–1
1.0
–2
0.9
–3
0.8
To select one of the 256 individual responses, the according
gain values for each filter, which range from –8 to +7, must be
programmed into the Filter Gain register.
–4
–5
0.7
–6
0.6
–7
–8
0.5
0
2
4
6
8
FREQUENCY – MHz
10
12
14
0
2
4
6
8
FREQUENCY – MHz
10
12
14
ADAPTIVE FILTER MODE
The derivative of the incoming signal is compared to the three
programmable threshold values: Adaptive Filter Threshold
A, B, C.
The edges can then be attenuated with the settings in Adaptive
Filter Gain 1, 2, 3 registers and Filter Gain register.
According to the settings of the Adaptive Mode control (MR56),
two Adaptive Filter Modes are available:
1. Mode A: is used when Adaptive Filter Mode (MR56) is set
to “0.” In this case, Filter B (LPF) will be used in the adaptive filter block. Also, only the programmed values for
Gain B in the Filter Gain, Adaptive Filter Gain 1, 2, 3 are
applied when needed. The Gain A values are fixed and cannot be changed.
1.6
MAGNITUDE RESPONSE – Linear Scale
The Adaptive Filter Threshold A, B, C registers, the Adaptive
Filter Gain 1, 2, 3 registers, and the Filter Gain register are used
in Adaptive Filter mode. To activate the Adaptive Filter control,
Sharpness Filter must be enabled (MR17 = “1”) and Adaptive
Filter Control must be enabled (MR57 = “1”).
1.5
1.4
1.3
1.2
1.1
1.0
FREQUENCY RESPONSE IN SHARPNESS FILTER MODE
WITH KA = 3 and KB = 7
Figure 37. Frequency Response in Sharpness Filter Mode
2. Mode B: is used when Adaptive Filter Mode (MR56) is set
to “1.” In this mode a cascade of Filter A and Filter B is used.
Both settings for Gain A and Gain B in the Filter Gain,
Adaptive Filter Gain 1, 2, 3 become active when needed.
–22–
REV. A
ADV7195
ADAPTIVE FILTER GAIN 1
AFG1 (AFG1)7–0
(Address (SR5-SR0) = 22H)
AFG37
This 8-bit-wide register is used to program the gain applied to
signals that lie above Adaptive Filter Threshold A but are smaller
than Adaptive Filter Threshold B.
AFG17
AFG16
AFG15
AFG14
AFG13
AFG12
AFG11
AFG17–AFG14
AFG13–AFG10
GAIN B
GAIN A
AFG10
AFG35
AFG34
AFG33
AFG32
AFG31
AFG37–AFG34
AFG33–AFG30
GAIN B
GAIN A
AFG30
Figure 40. Adaptive Filter Gain 3 Register
Gain A and Gain B values vary from –8 to +7.
Settings for (AFG1)3–0 have no effect unless Adaptive Mode
Control is set to Mode B (MR56 = “1”).
AFG36
ADAPTIVE FILTER THRESHOLD A
AFTA AFTA7–0
(Address (SR5–SR0) = 25H)
This 8-bit-wide register is used to program the threshold value
for small edges. The recommended programmable threshold
range is from 16–235, although any value in the range of 0–255
can be used.
AFTA7
Figure 38. Adaptive Filter Gain 1 Register
AFTA6
AFTA5
AFTA4
AFTA3
AFTA2
AFTA1
AFTA0
AFTA7–AFTA0
ADAPTIVE FILTER GAIN 2
AFG2 (AFG2)7–0
(Address (SR5–SR0) = 23H)
ADAPTIVE FILTER
THRESHOLD A
This 8-bit-wide register is used to program the gain applied to
signals that lie above Adaptive Filter Threshold B but are smaller
than Adaptive Filter Threshold C.
Gain A and Gain B values vary from –8 to +7.
Settings for (AFG2)3–0 have no effect unless Adaptive Mode
Control is set to Mode B (MR56 = “1”).
AFG27
AFG26
AFG25
AFG24
AFG23
AFG22
AFG21
AFG27–AFG24
AFG23–AFG20
GAIN B
GAIN A
AFG20
Figure 41. Adaptive Filter Threshold A Register
ADAPTIVE FILTER THRESHOLD B
AFTB AFTB7–0
(Address (SR5–SR0) = 26H)
This 8-bit-wide register is used to program the threshold value
for medium edges and has priority over Adaptive Threshold A.
The recommended programmable threshold range is from
16–235, although any value in the range of 0–255 can be used.
AFTB7
AFTB6
AFTB5
AFTB4
This 8-bit-wide register is used to program the gain applied to
signals that lie above Adaptive Filter Threshold C.
Gain A and Gain B values vary from –8 to +7.
Settings for (AFG3)3–0 have no effect unless Adaptive Mode
Control is set to Mode B (MR56 = “1”).
AFTB1
AFTB0
AFTB7–AFTB0
Figure 42. Adaptive Filter Threshold B Register
ADAPTIVE FILTER THRESHOLD C
AFTC AFTC7–0
(Address (SR5–SR0) = 27H)
This 8-bit-wide register is used to program the threshold value
for large edges and has priority over Adaptive Threshold A and
B. The recommended programmable threshold range is from
16–235, although any value in the range of 0–255 can be used.
The gain applied to signals that lie below Adaptive Threshold A
is programmed in the Filter Gain register.
AFTC7
At any one time only one of the following registers is active: AFG1,
AFG2, AFG3, FG. The gain values can be preprogrammed and
become active whenever the threshold conditions for the according register are met. To program the Adaptive Filter Gain registers
the same register settings are used as for the Filter Gain register.
REV. A
AFTB2
ADAPTIVE FILTER
THRESHOLD B
Figure 39. Adaptive Filter Gain 2 Register
ADAPTIVE FILTER GAIN 3
AFG3 (AFG3)7–0
(Address (SR5–SR0) = 24H)
AFTB3
AFTC6
AFTC5
AFTC4
AFTC3
AFTC2
AFTC1
AFTC7–AFTC0
ADAPTIVE FILTER
THRESHOLD C
Figure 43. Adaptive Filter Threshold C
–23–
AFTC0
ADV7195
SHARPNESS FILTER AND ADAPTIVE FILTER
APPLICATION EXAMPLES
Sharpness Filter Application
The sharpness filter can be used to enhance or attenuate the Y
video output signal.
The following register settings were used to achieve the results
shown in Figure 44a and Figure 44b.
Input data was generated by an external signal source.
Table V.
Address
Register Setting
00hex
01hex
02hex
03hex
04hex
05hex
09hex
10hex
10hex
10hex
10hex
10hex
10hex
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Filter Gain
Filter Gain
Filter Gain
Filter Gain
Filter Gain
Filter Gain
TEK RUN
40hex
81hex
00hex
78hex
00hex
00hex
3Ehex
00hex (a)
08hex (b)
04hex (c)
40hex (d)
80hex (e)
22hex (f)
The effect of the sharpness filter can also be seen when using
the internally generated crosshatch pattern.
Table VI.
Address
00hex
01hex
02hex
03hex
04hex
05hex
09hex
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
TEK RUN
TRIG’D
T
Register Setting
00hex
85hex
00hex
38hex
00hex
00hex
3Ehex
TRIG’D
T
T
T
(D)
(A)
1
R2
(E)
(B)
R1
R4
(F)
(C)
R2
1
CH1 500mV
REF4
500mV
CH1 500mV
M 4.00s
CH1
ALL FIELDS
4.00s T
9.99976ms
REF2
500mV
M 4.00s
CH1
ALL FIELDS
9.99976ms
4.00s T
(b)
(a)
Figure 44. Sharpness Filter Control with Different Gain Settings for Filter Gain
–24–
REV. A
ADV7195
In toggling MR17 (Sharpness Filter Enable/Disable) and setting
the Filter Gain register value to 99hex it can be seen that the
line contours of the crosshatch pattern change their sharpness.
Figure 46 shows the output signal when changing the Adaptive
Filter Mode to Mode B (MR56 = “1”).
TEK RUN
Adaptive Filter Control Application
Figure 45 shows a typical signal to be processed by the Adaptive
Filter Control block.
TEK RUN
TRIG’D
T
T
TRIG’D
T
T
4
M 100ns
CH4
CH4 100mV
ALL FIELDS
12.8222ms
T
4
Figure 46. Output Signal from Adaptive Filter Control
M 100ns
CH4
CH4 100mV
ALL FIELDS
12.8222ms
T
Figure 45. Input Signal to Adaptive Filter Control
The Adaptive Filter Control can also be demonstrated using
the internally generated crosshatch test pattern and toggling
the Adaptive Filter Control Bit (MR57) using the following
register settings:
The following register settings were used to obtain the results
shown in Figure 47, i.e., to remove the ringing on the Y signal.
Input data was generated by an external signal source.
Address
Table VII.
Address
00hex
01hex
02hex
03hex
04hex
05hex
09hex
10hex
22hex
23hex
24hex
25hex
26hex
27hex
Register Setting
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Filter Gain
Adaptive Filter Gain 1
Adaptive Filter Gain 2
Adaptive Filter Gain 3
Adaptive Filter Threshold A
Adaptive Filter Threshold B
Adaptive Filter Threshold C
40hex
81hex
00hex
78hex
00hex
80hex
3Ehex
00hex
AChex
9Ahex
88hex
28hex
3Fhex
64hex
TEK RUN
Table VIII.
A00hex
01hex
02hex
03hex
04hex
05hex
06hex
07hex
08hex
09hex
10hex
22hex
23hex
24hex
25hex
26hex
27hex
Register Setting
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Color Y
Color Cr
Color Cb
Mode Register 6
Filter Gain
Adaptive Filter Gain 1
Adaptive Filter Gain 2
Adaptive Filter Gain 3
Adaptive Filter Threshold A
Adaptive Filter Threshold B
Adaptive Filter Threshold C
TRIG’D
T
T
4
M 100ns
CH4
CH4 100mV
ALL FIELDS
12.8222ms
T
Figure 47. Output Signal from Adaptive Filter Control
REV. A
–25–
40hex
85hex
00hex
78hex
00hex
80hex
6Chex
52hex
52hex
3Ehex
00hex
AChex
9Ahex
88hex
28hex
3Fhex
64hex
ADV7195
Figure 49 shows an example of how to program the ADV7195
to accept a different high definition standard but SMPTE293M,
SMPTE274M, SMPTE296M or ITU-R.BT1358 standard.
HDTV MODE
MODE REGISTER 0
MR0 (MR07–MR00)
(Address (SR4–SR0) = 00H)
Reserved (MR04)
Figure 50 shows the various operations under the control of
Mode Register 0.
A “0” must be written to this bit.
Input Standard (MR05)
MR0 BIT DESCRIPTION
Output Standard Selection (MR00-MR01)
Select between 1080i or 720p input.
These bits are used to select the output levels from the ADV7195.
This control bit allows to select the polarity of the DV input
control signal to be either active high or active low.
DV Polarity (MR06)
If EIA-770.3 (MR01–00 = “00”) is selected, the output levels will
be: 0 mV for blanking level, 700 mV for peak white (Y channel),
± 350 mV for Pr, Pb outputs and –300 mV for tri-level sync.
If Full Input Range (MR01–00 = “10”) is selected, the output
levels will be 700 mV for peak white for the Y channel, ±350 mV
for Pr, Pb outputs and –300 mV for Sync. This mode is used for
RS-170, RS-343A standard output compatibility.
Sync insertion on the Pr, Pb channels is optional. For output
levels, refer to the Appendix.
Input Control Signals (MR02–MR03)
These control bits are used to select whether data is input with
external horizontal, vertical and blanking sync signals or if the
data is input with embedded EAV/SAV codes. An Asynchronous timing mode is also available using TSYNC, SYNC and
DV as input control signals. These timing control signals have
to be programmed by the user.
Reserved (MR07)
A “0” must be written to this bit.
Table IX. Truth Table
SYNC
TSYNC
DV
1 –> 0
0
0 or 1
0
0 –> 1
0 or 1
0 –> 1
0 or 1
0
1
1
0 or 1
0 or 1
0 –> 1
1 –> 0
50% Point of Falling Edge of
Tri-Level Horizontal Sync
Signal, A
25% Point of Rising Edge of
Tri-Level Horizontal Sync
Signal, B
50% Point of Falling Edge of
Tri-Level Horizontal Sync
Signal, C
50% Start of Active Video, D
50% End of Active Video, E
CLK
SYNC
PROGRAMMABLE
INPUT TIMING
TSYNC
DV
SET MR06 = 1
ACTIVE VIDEO
HORIZONTAL SYNC
ANALOG
OUTPUT
81
66
A
66
B
243
1920
C
D
E
Figure 48. Async Timing Mode—Programming Input Control Signals for SMPTE295M Compatibility
525
VIDEO
OUTPUT
1
12
13
42
43
HSYNC
VSYNC
DV
Figure 49. DV Input Control Signal in Relation to Video Output Signal
–26–
REV. A
ADV7195
MODE REGISTER 1
MR1 (MR17–MR10)
(Address (SR4-SR0) = 01H)
Test Pattern Hatch/Frame (MR13)
If this bit is set to “0,” a crosshatch test pattern is output from
the ADV7195. The crosshatch test pattern can be used to test
monitor convergence.
Figure 51 shows the various operations under the control of
Mode Register 1.
If this bit is set to “1,” a uniform colored frame/field test pattern
is output from the ADV7195.
MR1 BIT DESCRIPTION
Pixel Data Enable (MR10)
The color of the lines or the frame/field is white by default but
can be programmed to be any color using the Color Y, Color
Cr, Color Cb registers.
When this bit is set to “0,” the pixel data input to the ADV7195
is blanked such that a black screen is output from the DACs.
When this bit is set to “1,” pixel data is accepted at the input
pins and the ADV7195 outputs to the standard set in “Output
Standard Selection” (MR01–00). This bit also must be set to
“1” to enable output of the test pattern signals.
VBI Open (MR14)
This bit enables or disables the facility of VBI data insertion
during the Vertical Blanking Interval.
For this purpose Lines 7–20 in 1080i and Lines 6–25 in 720p
can be used for VBI data insertion.
Input Format (MR11)
It is possible to input data in 4:2:2 format or in 4:4:4
HDTV format.
Reserved (MR15–MR17)
A “0” must be written to these bits.
Test Pattern Enable (MR12)
Enables or disables the internal test pattern generator.
MR07
MR06
MR07
MR05
MR04
INPUT
STANDARD
ZERO MUST
BE WRITTEN
TO THIS BIT
MR05
0
1
1080I
720P
MR03
MR04
MR02
MR01
MR00
INPUT CONTROL SIGNALS
ZERO MUST
BE WRITTEN
TO THIS BIT
MR03 MR02
0
0
1
1
HSYNC/VSYNC/DV
EAV/SAV
TSYNC/SYNC/DV
RESERVED
0
1
0
1
DV POLARITY
OUTPUT STANDARD SELECTION
MR06
0
ACTIVE HIGH
1
ACTIVE LOW
MR01 MR00
0
0
1
1
0
1
0
1
EIA770.3
RESERVED
FULL I/P RANGE
RESERVED
Figure 50. Mode Register 0
MR17
MR16
MR17–MR15
ZERO MUST
BE WRITTEN
TO THIS BIT
MR15
MR14
MR13
MR12
MR10
VBI OPEN
TEST PATTERN
ENABLE
PIXEL DATA
ENABLE
MR14
0
DISABLE
1
ENABLE
MR12
0
DISABLE
1
ENABLE
MR10
0
DISABLE
1
ENABLE
TEST PATTERN
HATCH/FRAME
MR13
0
HATCH
1
FIELD/FRAME
Figure 51. Mode Register 1
REV. A
MR11
–27–
INPUT FORMAT
MR11
0
4:4:4 Y CR CB
1
4:2:2 Y CR CB
ADV7195
MODE REGISTER 2
MR1 (MR27–MR20)
(Address (SR4–SR0) = 02H)
MODE REGISTER 3
MR3 (MR37–MR30)
(Address (SR4-SR0) = 03H)
Figure 53 shows the various operations under the control of
Mode Register 2.
Figure 54 shows the various operations under the control of
Mode Register 3.
MR2 BIT DESCRIPTION
Y Delay (MR20–MR22)
MR3 BIT DESCRIPTION
HDTV Enable (MR30)
With these bits it is possible to delay the Y signal with respect to
the falling edge of the horizontal sync signal by up to four pixel
clock cycles. Figure 52 demonstrates this facility.
When this bit is set to “1,” the ADV7195 reverts to HDTV
mode. When set to “0” the ADV7195 reverts to Progressive
Scan Mode (PS mode).
Color Delay (MR23–MR25)
Reserved (MR31–MR32)
With these bits it is possible to delay the color signals with
respect to the falling edge of the horizontal sync signal by up to
four pixel clock cycles. Figure 52 demonstrates this facility.
A “0” must be written to these bits.
DAC A Control (MR33)
Setting this bit to “1” enables DAC A, otherwise this DAC is
powered down.
Reserved (MR26–MR27)
A “0” must be written to these bits.
DAC B Control (MR34)
Setting this bit to “1” enables DAC B, otherwise this DAC is
powered down.
NO DELAY
Y OUTPUT
Y DELAY
DAC C Control (MR35)
Setting this bit to “1” enables DAC C, otherwise this DAC is
powered down.
MAX DELAY
NO DELAY
Reserved (MR36–MR37)
A “0” must be written to these bits.
PrPb OUTPUT
PrPb DELAY
MAX
DELAY
Figure 52. Y and Color Delay
MR27
MR26
MR27–MR26
A ZERO MUST
BE WRITTEN
TO THESE BITS
MR25
MR24
MR23
MR22
COLOR DELAY
MR25 MR24 MR23
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
MR21
MR20
Y DELAY
MR22 MR21 MR20
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
0 PCLK
1 PCLK
2 PCLK
3 PCLK
4 PCLK
0 PCLK
1 PCLK
2 PCLK
3 PCLK
4 PCLK
Figure 53. Mode Register 2
MR37
MR37–MR36
ZERO MUST BE
WRITTEN TO
THESE BITS
MR36
MR35
MR34
MR33
DAC B CONTROL
MR34
0
POWER-DOWN
1
NORMAL
MR32
MR32–MR31
ZERO MUST BE
WRITTEN TO
THESE BITS
DAC C CONTROL
DAC A CONTROL
MR35
0
POWER-DOWN
1
NORMAL
MR33
0
POWER-DOWN
1
NORMAL
MR31
MR30
HDTV ENABLE
MR30
0
DISABLE
1
ENABLE
Figure 54. Mode Register 3
–28–
REV. A
ADV7195
MODE REGISTER 4
MR4 (MR47–MR40)
(Address (SR4–SR0) = 04H)
Color Output Swap (MR53)
By default DAC B is configured as the Pr output and DAC C as
the Pb output. In setting this bit to “1,” the DAC outputs can
be swapped around so that DAC B outputs Pb and DAC C outputs Pr. Table X demonstrates this in more detail.
Figure 55 shows the various operations under the control of
Mode Register 4.
MR4 BIT DESCRIPTION
Timing Reset (MR40)
Reserved (MR54–MR57)
A “0” must be written to these bits.
Toggling MR40 from low to high and low again resets the internal horizontal and vertical timing counters.
Table X. Relationship Between Input Pixel Port, MR53
and DAC B, DAC C Outputs
Reserved (MR41–MR47)
A “0” must be written to these bits.
In 4:4:4 Input Mode
MODE REGISTER 5
MR5 (MR57–MR50)
(Address (SR4–SR0) = 05H)
Color Data
Input on Pins
MR53
Analog Output
Signal
Cr9–0
Cb/Cr9–0
Cr9–0
Cb/Cr9–0
0
0
1
1
DAC B
DAC C
DAC C
DAC B
Color Data
Input on Pins
MR53
Analog Output
Signal
Cr9–0
Cb/Cr9–0
Cb/Cr9–0
0 or 1
0
1
Not Operational
DAC C (Pb)
DAC C (Pr)
Figure 56 shows the various operations under the control of
Mode Register 5.
MR5 BIT DESCRIPTION
Reserved (MR50)
In 4:2:2 Input Mode
This bit is reserved for the revision code.
RGB Mode (MR51)
When RGB mode is enabled (MR51 = “1”), the ADV7195
accepts unsigned binary RGB data at its input port. This control
is also available in Async Timing Mode.
Sync on PrPb (MR52)
By default the color component output signals Pr, Pb do not contain any horizontal sync pulses. If required, they can be inserted
when MR52 = “1.” This control is not available in RGB Mode.
MR47
MR46
MR45
MR44
MR43
MR42
MR41
MR47–MR41
MR40
TIMING RESET
ZERO MUST BE
WRITTEN TO
THESE BITS
MR40
Figure 55. Mode Register 4
MR57
MR56
MR55
MR57–MR54
ZERO MUST
BE WRITTEN
TO THESE BITS
MR54
MR53
COLOR OUTPUT SWAP
MR53
0
1
DAC B = PR
DAC C = R
MR52
MR51
MR50
SYNC ON PrPb
MR52
0
DISABLE
1
ENABLE
MR50
RESERVED FOR
REVISION CODE
RGB MODE
MR51
0
DISABLE
1
ENABLE
Figure 56. Mode Register 5
REV. A
–29–
ADV7195
DAC TERMINATION AND LAYOUT CONSIDERATIONS
Voltage Reference
PC BOARD LAYOUT CONSIDERATIONS
The ADV7195 is optimally designed for lowest noise performance, both radiated and conducted noise. To complement the
excellent noise performance of the ADV7195, it is imperative
that great care be given to the PC board layout.
The ADV7195 contains an onboard voltage reference. The VREF
pin is normally terminated to VAA through a 0.1 µF capacitor when
the internal VREF is used. Alternatively, the ADV7195 can be
used with an external VREF (AD589).
The layout should be optimized for lowest noise on the ADV7195
power and ground lines. This can be achieved by shielding the
digital inputs and providing good decoupling. The lead length
between groups of VAA and AGND, and VDD and DGND pins,
should be kept as short as possible to minimize inductive ringing.
Resistor RSET is connected between the RSET pin and AGND
and is used to control the full-scale output current and therefore the DAC voltage output levels. For full-scale output, RSET
must have a value of 2470 Ω; RLOAD has a value of 300 Ω.
When an input range of 0–1023 is selected, the value of RSET
must be 2820 Ω.
It is recommended that a four-layer printed circuit board be
used. With power and ground planes separating the layer of the
signal carrying traces of the components and solder-side layer.
Placement of components should be considered to separate
noisy circuits such as crystal clocks, high-speed logic circuitry,
and analog circuitry.
The ADV7195 has three analog outputs, corresponding to Y,
Pr, Pb video signals. The DACs must be used with external
buffer circuits in order to provide sufficient current to drive an
output device. Suitable op amps are the AD8009, AD8002,
AD8001, or AD8057. To calculate the output full-scale current
and voltage, the following equations should be used:
There should be a separate analog ground plane (AGND) and
a separate digital ground plane (GND).
VOUT = IOUT × RLOAD
Power planes should encompass a digital power plane (VDD)
and an analog power plane (VAA). The analog power plane
should contain the DACs and all associated circuitry, and the
VREF circuitry.
IOUT = [VREF × k]/RSET
k = 5.66, for I/P Ranges 64–940, 64–960, O/P Standards
EIA-770.1–3
The digital power plane should contain all logic circuitry. The
analog and digital power planes should be individually connected to the common power plane at one single point through
a suitable filtering device such as a ferrite bead.
k = 6.46, FCI Input Ranges 0–1023, Output Standard
RS-170/343A
VREF = 1.235 V
POWER SUPPLY DECOUPLING
FOR EACH POWER SUPPLY GROUP
VAA
10nF
0.1F
VAA
VAA
10nF
0.1F
0.1F
24, 35
COMP
VAA
1, 12
VDD
DAC A
Cb/Cr0–Cb/Cr9
Y OUTPUT
300
Cr0–Cr9
Pr (V) OUTPUT
DAC B
300
Y0–Y9
UNUSED
INPUTS
SHOULD BE
GROUNDED
ADV7195
Pb (U) OUTPUT
DAC C
HSYNC/SYNC
300
VAA
VSYNC/TSYNC
VAA
100
DV
5k
VAA
5k
SCL
100
4.7k
MPU BUS
SDA
RESET
4.7F
6.3V
VREF
27MHz, 74.25MHz OR
74.1758MHz CLOCK
RSET
CLKIN
VAA
ALSB
AGND
GND
26, 33
2.47k OR
2.82k
13, 52
4.7k
Figure 57. Circuit Layout
–30–
REV. A
ADV7195
DAC output traces on a PCB should be treated as transmission
lines. It is recommended that the DACs be placed as close as
possible to the output connector, with the analog output traces
being as short as possible (less than 3 inches). The DAC termination resistors should be placed as close as possible to the
DAC outputs and should overlay the PCB’s ground plane. As
well as minimizing reflections, short analog output traces will
reduce noise pickup due to neighboring digital circuitry.
Due to the high clock rates used, long clock lines to the ADV7195
should be avoided to minimize noise pickup. Any active pull-up
termination resistors for the digital inputs should be connected
to the digital power plane and not the analog power plane.
Supply Decoupling
For optimum performance, the analog outputs should be source
and load terminated, as shown in Figure 58. The termination
resistors should be as close as possible to the ADV7195 to minimize reflections.
Analog Signal Interconnect
The ADV7195 should be located as close as possible to the
output connectors, thus minimizing noise pickup and reflections due to impedance mismatch.
Noise on the analog power plane can be further reduced by the
use of decoupling capacitors.
Optimum performance is achieved by the use of 0.1 µF ceramic
capacitors. Each of group of VAA or VDD pins should be individually decoupled to ground. This should be done by placing
the capacitors as close as possible to the device with the capacitor leads as short as possible, thus minimizing lead inductance.
Any unused inputs should be tied to ground.
Video Output Buffer and Optional Output Filter
Output buffering is necessary in order to drive output devices,
such as progressive scan or HDTV monitors.
Digital Signal Interconnect
Analog Devices produces a range of suitable op amps for this
application. Suitable op amps would be the AD8009, AD8002,
AD8001, or AD8057. More information on line driver buffering
circuits is given in the relevant op amp data sheets.
The digital signal lines should be isolated as much as possible
from the analog outputs and other analog circuitry. Digital signal
lines should not overlay the analog power plane.
+5V
0.1F
DAC A
10F
LPF
75 COAX
AD8057
75
75
0.1F
ADV7195
10F
–5V
+5V
0.1F
DAC B
PROGRESSIVE
SCAN
MONITOR
10F
LPF
75 COAX
AD8057
75
75
0.1F
10F
+5V
+5V
0.1F
DAC C
10F
LPF
75 COAX
AD8057
75
0.1F
75
10F
–5V
Figure 58. Output Buffer and Optional Filter
REV. A
–31–
ADV7195
An optional analog reconstruction LPF might be required as an
antialias filter if the ADV7195 is connected to a device that
requires this filtering.
REGISTER SETTINGS
Table XI. Register Settings on Power-Up
The Eval ADV7195/ADV7196/ADV7197 EB evaluation board
uses the ML6426 Microlinear IC, which provides buffering and
low-pass filtering for HDTV applications.
Address
The Eval ADV7195/ADV7196/ADV7197 EB Rev. B and Rev. C
evaluation board uses the AD8057 as a buffer and a sixth order
filter as a LPF.
6.8H
600R
10H
6.8pF
22pF
2.2H
18pF
600R
AD8057
Figure 59. Example/Cr Output Filter:
PS Mode/2× Oversampling
498
63n
0
MAGNITUDE (dB)
–5
GROUP DELAY (SEC)
–15
198
36n
–20
97.6
27n
PHASE (DEG)
–25
0
18n
–30
–102
9n
–202
2
3
4
5
6 7 8 9 10
00hex
00hex
00hex
38hex
00hex
00hex
A0hex
80hex
80hex
00hex
00hex
AChex
9Ahex
88hex
28 hex
3Fhex
64 hex
Table XII. Internal Colorbars (Hatch), Progressive Scan Mode
298
45n
1
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Color Y
Color Cr
Color Cb
Mode Register 6
Filter Gain
Adaptive Filter Gain 1
Adaptive Filter Gain 2
Adaptive Filter Gain 3
Adaptive Filter Threshold A
Adaptive Filter Threshold B
Adaptive Filter Threshold C
398
54n
–10
–35
00hex
01hex
02hex
03hex
04hex
05hex
06hex
07hex
08hex
09hex
10hex
22hex
23hex
24hex
25hex
26hex
27hex
Register Setting
2
3
FREQUENCY – MHz
4 0n
Address
00hex
01hex
02hex
03hex
04hex
05hex
06hex
07hex
08hex
09hex
Figure 60. Frequency Response|C1 Filter
Circuit in above Figure
Register Setting
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Color Y
Color Cr
Color Cb
Mode Register 6
00hex
05hex
00hex
38hex
00hex
00hex
xxhex
xxhex
xxhex
3Ehex
Table XIII. Internal Colorbars (Field), HDTV Mode
Address
00hex
01hex
02hex
03hex
04hex
05hex
06hex
07hex
08hex
–32–
Register Setting
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Color Y
Color Cr
Color Cb
00hex
0Dhex
00hex
39hex
00hex
00hex
xxhex
xxhex
xxhex
REV. A
ADV7195
INPUT CODE
EIA-770.2, STANDARD FOR Y
OUTPUT VOLTAGE
INPUT CODE
940
EIA-770.3, STANDARD FOR Y
OUTPUT VOLTAGE
700mV
700mV
940
ACTIVE VIDEO
ACTIVE VIDEO
300mV
0mV
64
0mV
64
–300mV
–300mV
EIA-770.3, STANDARD FOR Pr/Pb
EIA-770.2, STANDARD FOR Pr/Pb
OUTPUT VOLTAGE
960
350mV
300mV
350mV
960
OUTPUT VOLTAGE
ACTIVE VIDEO
0mV
512
ACTIVE VIDEO
0mV
512
–300mV
–350mV
64
–300mV
–350mV
64
Figure 61. EIA-770.2 Standard Output Signals (525p)
INPUT CODE
EIA-770.1, STANDARD FOR Y
Figure 63. EIA-770.3 Standard Output Signals (1080i, 720p)
OUTPUT VOLTAGE
INPUT CODE
782mV
940
714mV
Y-OUTPUT LEVELS
FOR FULL I/P SELECTION
OUTPUT VOLTAGE
700mV
1023
ACTIVE VIDEO
ACTIVE VIDEO
64
0mV
0mV
64
–300mV
–286mV
EIA-770.1, STANDARD Pr/Br
PrPb-OUTPUT LEVELS
FOR FULL I/P SELECTION
1023
960
OUTPUT VOLTAGE
OUTPUT VOLTAGE
700mV
350mV
ACTIVE VIDEO
ACTIVE VIDEO
512
0mV
64
–300mV
–300mV
64
–350mV
Figure 64. Output Levels for Full I/P Selection
Figure 62. EIA-770.1 Standard Output Signals (525p)
REV. A
0mV
–33–
ADV7195
SMPTE293M
ANALOG
WAVEFORM
OHDATUM
ANCILLARY DATA
(OPTIONAL)
EAV CODE
F 0 0 F
F 0 0 V
H
INPUT PIXELS
F 0 0 F
F 0 0 V
H
719
C
C
b Y r
C
Y r Y
4 CLOCK
4 CLOCK
SAMPLE
NUMBER
DIGITAL
ACTIVE LINE
SAV
CODE
723 736
799
857
854
0
719
DIGITAL HORIZONTAL BLANKING
FVH = FVH AND PARITY BITS
SAV = LINE 43–525 = 200H
SAV = LINE 1–42 = 2AC
EAV = LINE 43–525 = 274H
EAV = LINE 1–42 = 2D8
Figure 65. EAV/SAV Input Data Timing Diagram—SMPTE293M
OHDATUM
SMPTE274M
ANALOG
WAVEFORM
4T
EAV
CODE
INPUT PIXELS
272T
ANCILLARY DATA
(OPTIONAL) OR BLANKING CODE
F 0 0 F
F 0 0 V
H
2112
2116 2156
DIGITAL
ACTIVE LINE
C
F 0 0 F C
F 0 0 V b Y r
H
4 CLOCK
SAMPLE
NUMBER
1920T
4T
SAV
CODE
C
r Y
4 CLOCK
0
2199
44
188
192
2111
FVH = FVH AND PARITY BITS
SAV/EAV = LINE 1–562: F = 0
SAV/EAV = LINE 563–1125: F = 1
SAV/EAV = LINE 1–20; 561–583; 1124–1125: V = 1
SAV/EAV = LINE 21–560; 584–1123: V = 0
Figure 66. EAV/SAV Input Data Timing Diagram—SMPTE274M
–34–
REV. A
ADV7195
ACTIVE VIDEO
522
523
ACTIVE VIDEO
VERTICAL BLANK
524
525
1
5
2
6
7
8
9
13
12
10
11
42
42
43
44
Figure 67. SMPTE293M (525p)
ACTIVE VIDEO
ACTIVE VIDEO
VERTICAL BLANK
622
623
624
625
2
1
4
5
6
7
8
9
10
11
12
43
13
44
45
Figure 68. ITU-R.BT1358 (625p)
DISPLAY
VERTICAL BLANKING INTERVAL
747
748
749
1
750
2
3
4
5
6
7
8
25
26
27
744
745
Figure 69. SMPTE296M (720p)
DISPLAY
FIELD 1
VERTICAL BLANKING INTERVAL
1124
1125
1
2
3
4
5
6
7
8
20
21
22
560
DISPLAY
FIELD 2
VERTICAL BLANKING INTERVAL
561
562
563
564
565
566
567
568
569
Figure 70. SMPT274M (1080i)
REV. A
–35–
570
583
584
585
1123
ADV7195
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.557 (14.15)
0.537 (13.65)
0.398 (10.11)
0.390 (9.91)
0.094 (2.39)
0.084 (2.13)
0.037 (0.95)
0.026 (0.65)
C00232–0–5/02(A)
52-Lead Plastic Quad Flatpack
(S-52)
52
1
40
39
PIN 1
0.398 (10.11)
0.390 (9.91)
0.557 (14.15)
0.537 (13.65)
SEATING
PLANE
TOP VIEW
(PINS DOWN)
0.012 (0.30)
0.006 (0.15)
0.008 (0.20)
0.006 (0.15)
13
14
0.0256
(0.65)
BSC
0.014 (0.35)
0.010 (0.25)
PRINTED IN U.S.A.
0.082 (2.09)
0.078 (1.97)
27
26
–36–
REV. A
Similar pages