AIMTEC AM10TW-IZ 10 watt | dc-dc converter Datasheet

Series AM10TW-IZ
10 Watt | DC-DC Converter
FEATURES:









Short Circuit & OVP Protection
24 Pin DIP Package
Wide 4:1 input range
Power modules for PCB mounting
No minimum load
Operating temperature -40oC to + 75oC
Regulated output
Low ripple and noise
Input/output Isolation voltage 1500VDC
Models
Single output
Model
Input
Voltage (V)
Output
Voltage
(V)
Output Current
max (mA)
Capacitive
Load, max(uf)
Ripple & Noise
max, (% mV p-p)
Efficiency
(%)
AM10TW-2403SIZ
AM10TW-2405SIZ
AM10TW-2412SIZ
AM10TW-2415SIZ
AM10TW-4803SIZ
AM10TW-4805SIZ
AM10TW-4812SIZ
AM10TW-4815SIZ
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
3.3
5
12
15
3.3
5
12
15
2000
2000
830
660
2000
2000
830
660
4200
3200
600
390
4200
3200
600
390
80
80
120
150
80
80
120
150
71
75
78
78
73
83
81
81
Model
Input
Voltage (V)
Output
Voltage
(V)
Output Current
max (mA)
Capacitive
Load, max(uf)
Ripple & Noise
max, (%)
Efficiency
(%)
AM10TW-2405DIZ
AM10TW-2412DIZ
AM10TW-2415DIZ
AM10TW-4805DIZ
AM10TW-4812DIZ
AM10TW-4815DIZ
9-36
9-36
9-36
18-75
18-75
18-75
±5
±12
±15
±5
±12
±15
±1800
±300
±200
±1800
±300
±200
80
120
150
80
120
150
75
79
80
77
80
80
Models
Dual output
±1000
±410
±330
±1000
±410
±330
Input Specifications
Parameters
Nominal
Typical
24
48
9-36
18-75
24 Vin
48 Vin

Voltage range
Filter
Maximum
Units
VDC
Capacitor
Absolute Maximum Rating
Permissible absolute maximum duration
Transient Voltage Deviation
50
100
100
5
VDC
ms
VDC
Isolation Specifications
Parameters
Tested I/O voltage
Resistance
Capacitance
Conditions
Typical
60 sec
Rated
Units
1500
VDC
MOhm
pF
Maximum
Units
> 1000
470
Output Specifications
Parameters
Conditions
Typical
Voltage accuracy
Short Circuit protection
Short Circuit restart
www.aimtec.com
F 051e R12.A
±2
%
Continuous
Auto recovery
Tel: +1 514 620 2722
1 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM10TW-IZ
10 Watt | DC-DC Converter
Output Specifications (continued)
Parameters
Over voltage protection
Over load protection
Line voltage regulation
Load voltage regulation (Single)
Load voltage regulation (Dual)
Temperature coefficient
Conditions
Typical
Zener diode clamp
Auto recovery
HL-LL
0 – 100% full load
0 – 100% full load
>110%
Over 110% full load
±0.5
±0.5
±2
±0.05
80 mV p-p
1% Vout p-p
3.3 & 5V models
12 & 15V models
Ripple & Noise
Maximum
Units
VDC
%
%
%
%/oC
mV
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Switching frequency
100% load
300
KHz
o
Operating temperature
Derating above +50 oC
-40 to +75
C
o
Storage temperature
-55 to +115
C
o
Case Temperature
+95
C
Cooling
Free air convection
Humidity
95
%
Case material
Nickel coated cooper
Weight
18
g
Dimensions (L x W x H)
Tolerance ±0.02 inch, ±0.5mm
1.25 x 0.80 x 0.40 inches
31.80 x 20.30 x 10.20 mm
MTBF
> 700 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC)
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Safety Specifications
Standards
Safety
UL (pending)
EN 55022, class A
EN 55024
Pin Out Specifications
Dimensions
Dual
-V Input
-V Input
N.C.
Omitted
N.C.
+V Output
Omitted
-V Output
+V Input
+V Input
-V Input
-V Input
Common
Omitted
-V Output
+ V Output
Omitted
Common
+V Input
+V Input
2
20.30
(0.80)
Single
2
3
9
10
11
14
15
16
22
23
22.80
(0.90)
0.50
(0.02)
3
9
11
Bottom View
23 22
2.50
(0.10)
16
14
5.00
(0.20)
Printed Face
3.80
(0.15)
10.20
(0.40)
Pin
31.80
(1.25)
15.20
(0.60)
Agency approvals
www.aimtec.com
F 051e R12.A
Tel: +1 514 620 2722
2 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM10TW-IZ
10 Watt | DC-DC Converter
Output Power %
Derating
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R12.A
Tel: +1 514 620 2722
3 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Similar pages