Kingbright APTB1612ESGC-F01 1.6x1.25mm bi-color smd chip led lamp Datasheet

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP
Part Number: APTB1612ESGC-F01
High Efficiency Red
Super Bright Green
Features
Descriptions
 1.6mmx1.25mm SMT LED, 0.65mm thickness.
 The High Efficiency Red source color devices are made
 Bi-color,low power consumption.
with Gallium Arsenide Phosphide on Gallium Phosphide
Orange Light Emitting Diode.
 Wide viewing angle.
 Ideal for backlight and indicator.
 The Super Bright Green source color devices are made
with Gallium Phosphide Green Light Emitting Diode.
 Package : 2000pcs / reel.
 Moisture sensitivity level : level 3.
 RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAF1097
REV NO: V.9A
DATE: JAN/08/2015
PAGE: 1 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203002009
Selection Guide
Part No.
Dice
Iv (mcd) [2]
@ 20mA
Lens Type
Viewing
Angle [1]
Min.
Typ.
8
15
*3
*7
5
12
*5
*12
2θ1/2
High Efficiency Red (GaAsP/GaP)
APTB1612ESGC-F01
120°
Water Clear
Super Bright Green (GaP)
Notes:
1.θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2.Luminous intensity/ luminous Flux: +/-15%.
*Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
High Efficiency Red
Super Bright Green
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
627
565
nm
IF=20mA
High Efficiency Red
Super Bright Green
617
568
nm
IF=20mA
Spectral Line Half-width
High Efficiency Red
Super Bright Green
45
30
nm
IF=20mA
C
Capacitance
High Efficiency Red
Super Bright Green
15
15
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
High Efficiency Red
Super Bright Green
2
2.2
2.5
2.5
V
IF=20mA
IR
Reverse Current
High Efficiency Red
Super Bright Green
10
10
uA
VR = 5V
Notes:
1.Wavelength: +/-1nm.
2.Forward Voltage: +/-0.1V.
3.Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
High Efficiency Red
Super Bright Green
Units
Power dissipation
75
62.5
mW
DC Forward Current
30
25
mA
Peak Forward Current [1]
160
140
mA
Reverse Voltage
5
V
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAF1097
REV NO: V.9A
DATE: JAN/08/2015
PAGE: 2 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203002009
APTB1612ESGC-F01
High Efficiency Red
SPEC NO: DSAF1097
REV NO: V.9A
DATE: JAN/08/2015
PAGE: 3 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203002009
Super Bright Green
SPEC NO: DSAF1097
REV NO: V.9A
DATE: JAN/08/2015
PAGE: 4 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203002009
APTB1612ESGC-F01
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAF1097
REV NO: V.9A
DATE: JAN/08/2015
PAGE: 5 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203002009
PACKING & LABEL SPECIFICATIONS
APTB1612ESGC-F01
Terms and conditions for the usage of this document
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAF1097
REV NO: V.9A
DATE: JAN/08/2015
PAGE: 6 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203002009
Similar pages